Particle deposition on the surface of the drying chamber poses the main drawback in the spray drying process, which reduces the product recovery and affects the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber was investigated in this study. The hydrophobic Polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless-steel substrates, which were used to mimick the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X1, %) and the treatment duration (X2, hr) on the contact angle of the substrate (°), which reflected the hydrophobicity of the surface. A three-dimensional (3D) response surface was constructed to examine the influence of the PDMS concentration and treatment duration on the contact angle readings, which serve as an indicator of the surface's hydrophobic characteristic. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 4.94 hr, while the PDMS coating for the stainless-steel substrate achieved an optimum contact angle of 98.31° with PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 1 hr. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH3, CH2, and CH3 functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and uniform nanostructure on the surface of PDMS-treated substrates, which indicated the reduction of wettability and the potential effect on unwanted biofouling on the spray drying chamber.

The spray drying process causes the buildup of an unspecified and unique pattern of wall deposits on the wall. The powder recovery of fruit juice by spray dryer is associated with stickiness problems because of the nature of food which contains low molecular weight sugars and organic acids, which have a low glass transition temperature (T_g). The surface properties of oxygen plasma treated-PTFE substrate were evaluated by using the different parameters of Plasma Enhanced Chemical Vapour Deposition (PECVD) prior to spray drying analysis. In this study, the fabrication method of nearly perfect superhydrophobic surfaces through plasma treatment with oxygen gas was generated and utilized. The plasma-treated PTFE were deposited from a fixed flow rate of oxygen gas with 30 cm³/min by varying the deposition time from 1 to 15 minutes to induce the hydrophobic surface of the PTFE substrate. The characterization techniques used to determine the morphology and chemical bonding of the substrate are field emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR), respectively. The hydrophobicity of the glass samples was determined by the water droplet contact angle. Sample prepared at radio frequency (RF) power of 90W for 15 minutes duration of treatment time showed porous and spongy like microstructure which correlates with the best performance of a good contact angle which creates the superhydrophobicity regime (171^o). Surface morphology analysis using scanning electron microscopy (SEM) showed changes in its roughness in the surface-treated glass substrate. The success of this method produced a huge potential for solving most of the food processing issues which relate to biofouling (e.g., powder stickiness) that would otherwise struggle to improve high productivity and recovery.

Having experienced large-scale disasters between 2004 and 2006, the fatalities due to large-scale disasters in 2018 were still high. In contrast, disaster risk management (DRM) and CDR in Japan have been continuously improved. Thus, there is a need to develop CDR for supporting DRM in Indonesia by learning from the Japanese experience, particularly in a disaster-prone area without large-scale disaster experience. This research was a pilot project on the development of CDR in Indonesia. The case study was a geological hazard-prone Lembang Fault area. People’s perception was collected using structured interviews, while demographic and local economic data was acquired from official statistical publications. Satellite imageries were utilized to acquire natural and built environment and land use/land cover and their changes between 2019 and 2021. Although the degrees of social capital, risk knowledge including indigenous knowledge and past disaster experience were high, government interventions on DRM and land administration are required to develop CDR in Lembang Fault area. Organized community development is expected rather than to solely involve NGOs. Moreover, strategies to develop economic resilience are needed to allow the community to bounce back from future disaster. Finally, a detail baseline data should be collected to develop DRM strategy and CDR.

Personalized surgery is not just a new trend but rather a patient-specific approach to therapy that makes it possible to adopt a targeted approach for a specific patient and closely mirrors the approach of personalized medicine. However, the application of tailored surgery in the context of cardiovascular replacement surgery was not systematically reviewed. The ability to customize a device is highly dependent on the collection of radiological image data for precise prosthesis modelling. These facts are essential to "tailor-made" device design for precise prosthesis implantation. According to this study, computed tomography (CT) was the most prominent imaging modality; however, transoesophageal echocardiography and echocardiography were also found to be helpful. Additionally, a dynamic finite element simulation is also an attractive alternative to the finite element analysis for an in-silico experiment. Nonetheless, there is a paucity of relevant publications and sporadic evidence. More clinical studies have been warranted, notwithstanding that the derived data and results from the insight into the use of therapeutic interventions may be of multiple directives in clinical practices and beyond. This study may help the integration of personalized devices for better comprehending predicted clinical outcomes, thus leading towards enhanced performance gains.

Topographic mapping using stereo plotting is not effective because it takes much time and labor-intensive. Thus, this research was conducted to find the effective way to extract building footprint for mapping acceleration. Building extraction method in this process comprises four steps: ground / non-ground filtering, building classification, segmentation, and building extraction. Non-ground points from filtering process were classified as building with the algorithm based on multi-scale local dimensionality to separate points at the maximum separability plane. Segmentation using segment growing was used to separate each building, so edge detection could be conducted for each segment to create boundary of each building. Lastly, building extraction was conducted through three steps: edge points detection, building delineation, and building regularization. With 10 samples and step 0.5, classification resulted quality and miss factor of 0.597 and 0.524, respectively. The quality was improved by segmentation process to 0.604, while miss factor was getting worse to 0.561. Meanwhile, on average shape index value from extracted building had 0.02 difference and the number of errors was 30% for line segment comparison. Regarding positional accuracy using centroid accuracy assessment, this method could produce RMSE of 1.169 meters.

The rapid development of transportation infrastructure in Malaysia had changed the mobility landscape of the country. While it would be a welcome advancement for many, older adults might find it difficult to keep up with their transportation uses and remain active. This study reviewed published articles on the travel behavior of older adults and its associated transportation determinants to explore how sustainable the transportation system is for this vulnerable cohort. Four databases were searched: PubMed, Scopus, ProQuest, and EBSCOhost. Inclusion criteria were older respondents, living in a community in Malaysia, addressing any travel behavior characteristics and written in English language. Review paper, letters, book citations, comments, editorials, and experimental and animal studies were excluded from this study. All in all, this review included seven studies extending from the year 2007 to 2020. The result showed that transportation use of older adults had shifted from relying on public transports to driving their own vehicle to move around. According to the finding of this study, besides personal and health factors, transport use of older adults was affected mainly by cost, public transport availability, road traffic and safety, the complexity of the transportation system, distance to public transit, availability of parking space, road condition and signage. It is concluded that an effective strategy to improve the transportation system is lauded to prevent unmet travel needs among the older adults in Malaysia.