The widespread use of renewable energy sources has considerably expanded distributed generation. An unbalanced load on distribution cables may also result from the recent increase in novel appliances and electric vehicles, the reverse power flow may create short-term overloads. These transient overloads increase the temperature for a short time beyond the limit, which causes degradation. However, the temperature distribution on the cable is not even. Therefore, the cable components are not degraded evenly and similarly. This publication describes the change in electrical properties of low-voltage cables caused by short-term cyclic artificial ageing to track the impact of these brief temperature rises. This study examines how cable structure affects the dielectric characteristics of cable specimens. Four cable samples, each measuring 50 cm in length (SZAMKAM 0.6/1 kV 16 mm2× 4 manufactured by Prysmian MKM Kft, Hungary) put through an accelerated ageing test in a temperature-controlled oven after changing their structures by removing their layers. Three rounds, each of six hours, accelerated thermal ageing were applied. After each round of ageing, the dielectric parameter tanδ and capacitance were measured by Dirana Dielectric Response Analyzer in the laboratory at room temperature 24±0.5∘C. Furthermore, the polarization and depolarization currents were also studied. The results show that changing the cable structure impacts the dielectric parameters, especially the effect of belting layer is significant. From point of view of aging the PVC belting layer protects the diffusion of plasticizers of inner structure.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

Ferrocene and its derivatives have ecologically effective antidetane properties. In this regard, ferrocene reacts with cyclic ketones and ferrosenylcarbinols are synthesized. It should be noted that ferrocene enters into electrophilic reactions and the process takes place in an acidic environment. In addition, the yield of the new product was small compared to the reactions of ferrocene with non-cyclic ketones. This is due to the spatial structures of molecules. The elemental analysis of obtained compounds was carried out; the structures were researched by cyclic voltammograms and Chronoamperometric.

The paper presents a new conception of quasi-distributed sensor for simultaneous measurement of several physical fields and the results of an experimental study of this sensor. A distinctive feature of the sensor defined by the sensitive RC elements connected in the original tree-like structure. The proposed is the structure of the sensor and measurement system as well as corresponding measurement algorithm. The high accuracy demonstrated by the sensor’s prototype gives possibility to effective use the proposed sensors in many technical and scientific applications.

Rajshahi, blessed by the geographical advantage provided by the river Padma, is a beautiful and one of the cleanest cities in Bangladesh. It presents a spectacular image and stunning sight to its residents. But Rapid urbanization created immense pressure on the infrastructures and cityscape by rescinding most of the natural assets and scenic beauty it possessed historically. The growing pressure of population influx accompanied by unplanned urbanization threatens the survival of its waterbodies, wetlands, and greeneries, which many other contemporary cities strive to achieve with hard-hearted planning measures. Moreover, the city suffers from inadequate provision of quality outdoor recreational facilities. Yet because of the verdant resources, it still can set an example of becoming green and fluid landscape. There are scopes to connect the city people to the urban landscape and blue-green infrastructures by applying proper planning and urban design techniques. For example, it can explore the potential and scope of a water-based transportation system to create outdoor recreation space for city dwellers as well as a transport mode in the city. This SECTION discusses the prospects and potential of enhancing recreational aspects of Circular Inland Waterways. It also analyzes the benefits of a network of waterways well-connected and integrated with the existing conventional transportation system to reduce pressure on land transport and promote a sustainable system. This research was conducted in two phases each involving a distinct approach. The first one was a macroscopic approach to probe the potential of the water transport system in Rajshahi city. The required data on traffic volume, traffic growth rate, roads and existing waterbodies were collected, and GIS and Remote Sensing tools were used to find the scope of waterway transport around Rajshahi City. In the second approach, a detailed design was proposed for a potential circular waterway network in the city. Results indicate that there is a huge prospect for introducing a circular waterway transport system around Rajshahi city to create a place of fluid landscape and minimize the pressure on the existing land transportation system.

Cultural practices and development level can influence a population’s household structures and mixing patterns. Within some populations households can be organized across multiple dwellings. This likely affects the spread of infectious disease spreads through these communities, however, current demographic data collection tools do not record these data. Methods: Between June–October 2018, the Contact And Mobility Patterns in remote Aboriginal Australian communities (CAMP-remote) pilot study recruited Aboriginal mothers with infants in a remote northern Australian community to complete a monthly iPad-based contact survey. Results: Thirteen mother-infant pairs (participants) completed 69 study visits between recruitment and the end of May 2019. Participants reported they and their other children slept in 28 dwellings during the study. The median dwelling occupancy, defined as people sleeping in the same dwelling on the previous night, was nine (range: 3.5–25). Participants who completed at least three responses (n=8) slept in a median of three dwellings (range: 2–9). Each month a median of 28% (range: 0%–63%) of the participants travelled out of the community. Including these data in disease transmission models amplified estimates of infectious disease spread in the study community, compared to models parameterized using census data. Conclusions: The lack of data on mixing patterns in populations where households can be organized across dwellings may negatively impact the accuracy of infectious disease models for these communities and the efficacy of public health actions they inform.

This work presents the first evidence that dissolved globular proteins change the arrangement of hydrogen bonds in water, with different proteins showing quantitatively different effects. Using ATR-FTIR (Attenuated Total Reflection – Fourier Transform Infrared) spectroscopic analysis of OH-stretch bands, we obtain quantitative estimates of the relative amounts of the previously reported four subpopulations of water structures coexisting in a variety of aqueous solutions. Where solvatochromic dyes can measure the properties of solutions of non-ionic polymers, the results correlate well with ATR-FTIR measurements. In protein solutions to which solvatochromic dye probes cannot be applied, NMR (Nuclear Magnetic Resonance) spectroscopy was used for the first time to estimate the hydrogen bond donor acidity of water. We found strong correlations between the solvent acidity and arrangement of hydrogen bonds in aqueous solutions for several globular proteins. Even quite similar proteins are found to change water properties in dramatically different ways.

The agro-biodiversity present in agro-ecosystems is fundamental in guaranteeing sustainability and resilience. However, there are very few proposals for evaluating it and, even less, ones that include indicators to analyze the influence of the structural and spatial configuration of a landscape in order to favor agro-biodiversity connectivity to productive systems, management and conservation practices, and the producer (farmer)’s perceptions, awareness and ability to favor it on his farm. The Main Agro-ecological Structure MAS is redefined as an environmental agro-biodiversity index. New indicators are established for a total of 10 criteria and 29 indicators of systems that describe the agro-biodiversity of agro-ecosystems. Methodologies for its evaluation are also described, and the possibility of adapting certain indicators according to the ecological and cultural contexts where the farms are located is discussed.

Chirality depends on particular symmetries. For crystal structures it describes the absence of mirror planes and inversion centers, and in addition to translations, only rotations are allowed as symmetry elements. However, chiral space groups have additional restrictions on the allowed screw rotations as a symmetry element, because they always appear in enantiomorphous pairs. This study classifies and distinguishes the chiral structures and space groups. The chirality is quantified using Hausdorff distances and continuous chirality measures and selected crystal structures are reported. The chirality is discussed for bulk solids and their surfaces. Moreover, the band structure, and thus, the density of states, is found to be affected by the same crystal parameters as the chirality. However, it is independent of handedness. The Berry curvature, as a topological measure of the electronic structure, depends on the handedness, but is not a proof for the chirality because it responds on the inversion of a structure. For molecules, optical circular dichroism is one of the most important measures for the chirality. Thus, it is proposed in this study that the circular dichroism in the angular distribution of photoelectrons in high symmetry configurations can be used to distinguish the handedness of chiral solids and their surfaces.

Given the documented wave-induced damage of elevated coastal decks during extreme natural hazards (e.g. hurricanes) in the last two decades, it is of utmost significance to decipher the wave-structure-interaction of complex deck geometries and quantify the associated loads. Therefore, this study focuses on the assessment of solitary wave impact on open-girder decks that allow the air to escape from the sides. To this end, an arbitrary Lagrangian-Eulerian (ALE) numerical method with a multi-phase compressible formulation is used for the development of three-dimensional hydrodynamic models, which are validated against a large-scale experimental dataset of a coastal deck. Using the validated model as a baseline, a parametric investigation of different deck geometries with a varying number of girders Ng and three different widths, was conducted. The results reveal that the Ng of a superstructure has a complex role and that for small wave heights the horizontal and uplift forces increase with the Ng, while for large waves the opposite happens. If the Ng is small the wave particles accelerate after the initial impact on the offshore girder leading to a more violent slamming on the onshore part of the deck and larger pressures and forces, however, if Ng is large then unsynchronized eddies are formed in each chamber, which dissipate energy and apply out-of-phase pressures that result in multiple but weaker impacts on the deck. The decomposition of the total loads into slamming and quasi-static components, reveals surprisingly consistent trends for all the simulated waves, which facilitates the development of predictive load equations. These new equations, which are a function of Ng and are limited by the ratio of the wavelength to the deck width, provide more accurate predictions than existing empirical methods, and are expected to be useful to both engineers and researchers working towards the development of resilient coastal infrastructure.

We report the results of the characterization of local Monte Carlo (MC) dynamics of an equilibrium bond fluctuation model polymer matrix (BFM), in time interval typical for MC simulations of non-linear optical phenomena in host-guest systems. The study contributes to the physical picture of the dynamical aspects of quasi-binary mosaic states characterized previously in the static regime. The polymer dynamics was studied at three temperatures (below, above and close to the glass transition), using time-dependent generalization of the static parameters which characterize local free volume and local mobility of the matrix. Those parameters play the central role in the kinetic MC model of host-guest systems. The analysis was done in terms of the probability distributions of instantaneous and time-averaged local parameters. The main result is the characterization of time scales characteristic of various local structural processes. Slowing down effects close to the glass transition are clearly marked. The approach yields an elegant geometric criterion for the glass transition temperature. A simplified quantitative physical picture of the dynamics of guest molecules dispersed in BFM matrix at low temperatures offers a starting point for stochastic modeling of host-guest systems.

Based on panel data of 31 provincial-level administrative units (excluding Hong Kong, Macao and Taiwan) in China from 2015 to 2019, using fixed effect model and mediation effect model, this paper makes an empirical analysis on the interaction among digital economy, industrial structure upgrade and high-quality economic development. The results show that, from the overall effect, the digital economy can significantly promote the high-quality development of the economy, and there are regular regional differences, and the relationship between the promotion intensity and the development level of the digital economy is proportional. From the mediation effect, in the relationship between digital economy and high-quality economic development, the upgrade of industrial structure has played a significant part of the mediation effect, the proportion of mediation effect is 25.17% . In addition, the mediation effect of industrial structure upgrade has obvious regional difference, the western area is the strongest, the eastern area is the second, the central area is the weakest. Based on the above research,the concrete policy suggestions are given to promote the development of digital economy and upgrade the level of industrial structure to promote the high-quality development of economy.

It has been more than a year since the first case of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) was found. This coronavirus has infected more than 110 million people worldwide by the end of February, 2021, and several virulent as well as more spreadable mutant forms of SARS-CoV-2 have emerged subsequently. In the latter group, three variants B.1.1.7, B.1.351, and P1 lineages, have been reported. Using computer simulation, the present paper investigates the structural differences between the wild type SARS-CoV-2 spike protein and its Asn501Tyr (N501Y) mutant variant. Time-based structural changes between the receptor binding domains of these two species are also examined. The N501Y mutation is common to all the three aforesaid mutant variants.

A solid structure, such as a road, building wall or envelop, used as a solar collector is considered an effective and new way to use renewable energy. This paper focused on the temperature characteristics of four structures exposed to sunshine: asphalt, red brick, composite cement and concrete road slab. Furthermore, the collected heat based on a hydraulic system was investigated experimentally. For the four structure slabs, their temperature differences are due to solar radiation absorption varied greatly by the material’s heat absorptance and color. Through the test, asphalt slab attained the highest temperature and had the weakest reflection among the structures. Compared with the others, the temperature of the asphalt slab was greater by 8.1%, 14.9% and 16.4% than the brick, composite cement and concrete, respectively. The reflection intensity growth ratio was defined and indicates the growth potential for absorbing radiation in the solid slab surface. From the experiments, it was concluded that a suitable selection of road materials can greatly improve the thermal absorption, conduction and penetration into the solid slab. The collected heat capability was approximately 250 W/m2 to 350 W/m2 in the natural summer condition. A black coating or a surface modification can collect more heat, reaching greater than 250 W/m2. The solar collecting heat efficiency with a surface configuration of the road slab can reach above 30% in the summer time.

Since the launch of Protein Data Bank (PDB) in 1971, Cartesian coordinate system (CCS) has been the default approach to specify atomic positions in biomolecular experimental structures with X, Y and Z. In 2020, a local spherical coordinate system (LSCS) approach was proposed as an alternative to CCS, i.e., ρ, θ and φ. Recently, the continued application of deep learning technology in protein structure prediction (PSP) saw a leap forward in the accuracy of PSP, as evidenced by AlphaFold of Google’s DeepMind. However, there still is room for the improvement of the performances of PSP algorithms to date. Given that geometrically, CCS and LSCS are like the two sides of a coin, this short article puts forward a hypothesis that the time is now ripe to end the half-a-century burial of ρ, θ and φ in PDB, and use them as LSCS features for the design of novel PSP algorithms in future.

Oligonucleotide conjugates with boron clusters have found applications in different fields of molecular biology, biotechnology, and biomedicine as potential agents for boron neutron capture therapy, siRNA components, and antisense agents. Particularly, closo-dodecaborate anion represents a high-boron containing residue with remarkable chemical stability and low toxicity, suitable for the engineering of different constructs for biomedicine and molecular biology. In the present work, we synthesized novel oligonucleotide conjugates of closo-dodecaborate attached to the 5'-, 3'-, or both terminal positions of DNA, RNA, 2'-O-Me RNA, and 2'-F-Py RNA oligomers. For their synthesis, we employed click reaction with the azido derivative of closo-dodecaborate. The key physicochemical characteristics of the conjugates have been investigated using high-performance liquid chromatography, gel electrophoresis, UV thermal melting, and circular dichroism spectroscopy. Incorporation of closo-dodecaborate residues at the 3'-end of all oligomers stabilized their complementary complexes, while analogous 5'-modification decreased duplex stability. Two boron clusters attached to the opposite ends of the oligomer only slightly influence the stability of complementary complexes of RNA oligonucleotide and its 2'-O-methyl and 2'-fluoro analogs. On the contrary, the same modification of DNA oligonucleotides significantly destabilized DNA/DNA duplex but gave a strong stabilization of the duplex with RNA target. According to CD spectroscopy results, two terminal closo-dodecaborate residues cause a prominent structural rearrangement of complementary complexes with a substantial shift from B-form to the A-form of the double helix. The revealed changes of key characteristics of oligonucleotides caused by incorporation of terminal boron clusters, such as the increase of hydrophobicity, change of duplex stability, and prominent structural changes for DNA conjugates, should be taken into account for the development of antisense oligonucleotides, siRNAs, or aptamers bearing boron clusters. These features may also be used for engineering of developing NA constructs with pre-defined properties.

In this study, we report a detailed experimental and theoretical investigation of three glycols, namely ethane-1,2-diol, 2-methoxyethan-1-ol and 1,2-dimethoxy ethane. For the first time, the X-Ray spectra of the latter two liquids was measured at room temperature, and they were compared with the newly measured spectrum of ethane-1,2-diol. The experimental diffraction patterns were interpreted very satisfactorily with molecular dynamics calculations, and suggest that in liquid ethane-1,2-diol most molecules are found in gauche conformation, with intramolecular hydrogen bond between the two hydroxyl groups. Intramolecular H-bonds are established in the mono-alkylated diol, but the interaction is weaker. The EDXD study also evidences strong intermolecular hydrogen-bond interactions, with short O···O correlations in both systems, while longer methyl-methyl interactions are found in 1,2-dimethoxy ethane. X-Ray studies are complemented by micro Raman investigations at room temperature and at 80°C, that confirm the conformational analysis predicted by X-Ray experiments and simulations.

The aim of this research was to test recent developments in the use of Remotely Piloted Aircraft Systems or Unmanned Aerial Vehicles (UAV) to map pasture biomass yield and nutrient status, across a selected range of field sites throughout the rangelands of Queensland. Improved pasture management begins with an understanding of the state of the resource base, UAV based methods can potentially achieve this at improved spatial and temporal scales. This study developed predictive models of both pasture yield and pasture nutrient status. An automated pasture height surface modelling technique was developed, tested and used along with field site measurements of pasture yields, to predict further estimates across each field site. Both prior knowledge and automated predictive modelling techniques were employed to predict pasture yield and nutrition. Pasture height surface modelling was assessed against field measurements using a rising plate meter, results reported correlation coefficients (R2) ranging from 0.2 to 0.4 for both woodland and grassland field sites. Accuracy of the predictive modelling was determined from further field measurements of pasture yield and on average indicated an error of 0.8 t ha-1 in grasslands and 1.3 t ha-1 in mixed woodlands across both modelling approaches. Correlation analyses between measures of pasture quality, acid detergent fibre and crude protein (ADF, CP), and spectral reflectance data indicated the visible red (651 nm) and red-edge (759 nm) regions were highly correlated (ADF R2 = 0.9 and CP R2 = 0.5 mean values). These findings agreed with previous studies linking specific absorption features with grass chemical composition. These results conclude that the practical application of such techniques, to efficiently and accurately map pasture yield and quality, is possible at the field site scale, however further research is needed, in particular further field sampling of both yield and nutrient elements across such a diverse landscape, with the potential to scale up to a satellite platform for broader scale monitoring.

Whether there is any inclination between structures and functions of antimicrobial peptides (AMPs) is a mystery yet to be unraveled. AMPs have various structures associated with many different antimicrobial functions, including antibacterial, anticancer, antifungal, antiparasitic and antiviral activities. However, none has yet reported any antimicrobial functional tendency within a specific category of protein/peptide structures nor any structural tendency of a specific antimicrobial function with respect to AMPs. Here we examine the relationships between structures categorized by three structural classification methods (CATH, SCOP and TM) and seven antimicrobial functions with respect to AMPs using an enrichment analysis. The results show that antifungal activities of AMPs were tightly related to two-layer sandwich structure of CATH, knottin fold of SCOP, and the first structural cluster of TM. The associations with knottin and TM cluster 1 even sustained through the AMPs with a low sequence identity. Besides, another significant mutual enrichment was observed between the third cluster of TM and anti-gram-positive-bacterial/anti-gram-negative-bacterial activities. The findings of the structure-function inclination further our understanding of AMPs and could help us design or discover new therapeutic potential AMPs.

Automatic control to any of robot manipulators, some kind of issues are being observed. A numerical method for solution generation to the inverse kinematics problem of redundant robotic manipulators is presented to obtain the smoothest algorithm as possible, leading to a robust iterative method. After the primary objective of the reachability of end-effectors to the target point is achieved, the aim is set to resolve the redundant degrees of freedom of redundant manipulator. This method is numerically stable since it converges to the correct answer with virtually any initial approximation, and it is not sensitive to the singular configurations of the manipulator. In addition, this technique is computationally effective and able to apply for serial manipulators with any DOF applications. A planar 3R-DOF serial link redundant manipulator is considered as exemplar problem for solving. Also, the continuum approach for resolving more complex structure with variable DoF is illustrated here and their brief applicability to support surgeries and adaptive use of artificial linkage moments is also calculated.

Late blight caused by the oomycete pathogen Phytophthora infestans is a devastating disease of potato and tomato worldwide, including Israel. The population structure of this pathogen was monitored in potato and tomato fields in Israel during a 36-year period of 1983-2019. Isolates of the pathogen were tested for sensitivity to phenylamide fungicides, mating type, race structure, and genotype. The phenotypic and genotypic structure of the population from potato have changed greatly from one year to another, from one season to the next, within a season and within a single field. Major changes also occurred in the population collected from tomato crops. The mechanisms driving these multiple changes and the heterogeneous nature of the population in Israel are shown to derive from multiple migration events of the pathogen via seed tubers from Europe and from fitness-driven selection processes.

As of today, there is not any direct report yet of the degree to which missing residues exist for experimentally determined membrane protein (MP) structures, which constitute more than half of current drug targets. With a chain- and position-specific visualisation and a statistical analysis of all MP structures inside PDB (as of September 25, 2019), this article argues that the experimentally uncharted territories (EUTs, i.e., consisting of missing residues) within PDB are pluggable and should be plugged with an experimental data-driven hybrid approach, and calls for continued development of MP structural determination with less and less EUTs, in light of MPs' crucial role in biological and biomedical research, both fundamental and pharmaceutical.

The study was conducted in north wollo, south wollo and orimiya zone, in Eastern Amhara with an aim to assess the resource potential of Acacia seyal in the selected sites. The data from the selected sites were collected using point center quarter method. A total of 90 quadrates from nine study areas with plot size 50m*50m, (22.5ha) were systematically located along each transect, 100 m apart, and was spatially captured with the aid of GPS. At every sampling point, four quadrants (90 degrees) were created, using the transect line and a line perpendicular to it. Species composition Acacia seyal structure and its regeneration status, at points along transects were taken to analyze diversity and target species structure of the sites. The highest and least density of Acacia seyal ha^-1 were attained by Mehale mecharie (148) and Alene sefer (52). The highest shannon weiner diversity and species richness was observed in Alene sefer(Kemessie). Acacia seyal structure in all study sites showed an inverted J shape except lastie gerdao (Gubalafeto). Therefore, Acacia seyal deserves immediate conservation and appropriate management measures in order to get sustainable product and services from the species. Based on the results, awareness creation on the values and management of Acacia seyal, study on the management options of Acacia seyal for firewood, fuel wood, charcoal production and also investigation of gum production techniques of Acacia seyal for the sustainable use of the resource are recommended.

In this paper we review a proposal to represent the geometric degrees of freedom of the gravitational field as a branched covering space, and introduce a new application of this in which the branch loci are 1- or 2-knots. This allows one to construct arbitrary smooth, closed 3- and 4-manifolds with enough geometric and topological information to write down a partition function and calculate statistical quantities in the thermodynamic limit. Further, we find clear evidence for a dimensional reduction of the spacetime geometry from four to two. As an example, we choose a family of smooth 4-manifolds presented in this way, and calculate the entropy of the system.

This article attempts to formulate a mathematical model for a potential explanation regarding the unavoidable impact of a rigid body's peculiar shape on the seamless flow over it. The solid body completely immersed in a Newtonian fluid and respectively has a relative open circuit flow on it will typically experience various observable phenomena like flow separation, flow transition, down-wash, stalling at the higher angle of attack, stalling velocity and how cambered airfoil can typically generate lift at a zero incidence angle. This article respectively represents an understanding of the laminar flow over a rigid body's external surface with due respect to its distinctive shape and size. This working paper formulates a more realistic and simplified mathematical model for open circuit laminar flow over a body, based on the historical data of aerodynamics and theoretical mechanics. This is intended to properly estimate forces on the continuous surface of the body in a laminar flow, to properly explain, understand and predict mentioned phenomena. Most of all the mechanism of streamline formation and its deformation with due regards to flow, shape and size of the body in an open-circuit laminar are formulated mathematically to enhance better design theory which can reduce experimentation while designing a streamlined body.

Unsteady flow is the most common and complicated form of fluid motion in nature. This paper takes the beaches of key waterways in the middle and lower reaches of the Yangtze River as the research object, analyzes the water surface distribution and average flow velocity distribution near the beach, and analyzes the differences. The relationship between the flow pattern of the steep slope and the water flow pattern of the entire survey area and the steep slope of the beach and its nearby water flow structure. The water flow near the beach is divided into four major blocks: the swelling water area, the falling water area, the backwater area and the maximum flow rate area. The water flow structure characteristics and the cause of each block are analyzed.

Impact load was applied to hardened cement paste (HCP) specimens using a gas gun to investigate microscopic changes in the specimens and develop a better response model of concrete subjected to impact load. Plasma emission was observed at the moment of impact at 420 m/s and the colour of the portion near the impact point turned brighter. This brighter portion was analysed, and it was observed that the pore structure was coarser compared to the other portion; however, the results of thermogravimetry and X-ray diffraction analysis were similar. A possible reason is that the generated heat was instantaneous and the rate of the temperature increase in the HCP decreased due to evaporation of water in the HCP. These results indicate that during impact at a few hundred m/s, porosity increase due to heat effect is more dominant than porosity decrease due to mechanical compaction.

By means of density functional theory (DFT) calculations, we have investigated the effect of hydrostatic pressure on the structural, electronic and elastic properties of the barium-doped silicon clathrate Ba8Si46 in the type-VIII structure (α phase). Physical properties are calculated under different conditions of pressure (0 GPa to 45 GPa) using the GGA-PBE functional, those calculations have been performed using the Cambridge serial total energy package CASTEP code within the Materials Studio package. Electronic properties have shown that the type-VIII Ba8Si46 has metal-like properties with a fundamental bandgap of 1 eV. Under pressure the fundamental bandgap increases slightly and the positions of the valence band maximum VBM and the conduction band minimum CBM remain unchanged. We found that the compound is mechanically stable under the pressure range, but this needs to be confirmed experimentally through synthesis, a comparison with the type-I and the guest-free counterparts has exhibited promising features for the type-VIII Ba8Si46.

In 2015, Romania was the first country in Europe that achieved EU targets regarding the share of renewables in the generation mix, far ahead of the 2020 deadline. Starting with the energy structure in Romania, the paper: (1) analyses the evolution of the main indicators in the renewable energy sector, (2) discloses the perspectives of renewable energy in Romania synthesizing the main trends of development in the field and (3) analyses the challenges facing with the development of renewable energy in Romania. Based on analyzing the exploratory data, the paper makes a preliminary prediction of the development of the sector for the future decades and proposes targeted countermeasures and suggestions. Romania still has unexploited potential concerning renewable energy sources. Because Romania registered a continuous economic growth, the demand for electricity is steadily growing, and this trend is expected to continue. Also, Romania could introduce a support mechanism for developing the potential of unexploited potential. The results of the present study may be useful for further research regarding public policies for the development of renewable energy. Also, it can represent a useful analysis in order to identify the future trends of renewable energy in Romania.

In this paper, ground tire rubber (GTR) was mechano-chemically modified with road bitumen 160/220 and subsequently treated using a microwave radiation. The combined impact of bitumen 160/220 content and microwave treatment on short-term devulcanization of GTR were studied by thermal camera, wavelength dispersive X-ray fluorescence spectrometry (WD-XRF), static headspace and gas chromatography-mass spectrometry (SHS-GC-MS), thermogravimetric analysis combined with Fourier transform infrared spectroscopy (TGA-FTIR), oscillating disc rheometer and static mechanical properties measurements. The obtained results showed that bitumen plasticizer prevent oxidation of GTR during microwave treatment and simultaneously improves processing and thermal stability of obtained reclaimed rubber.

Quantitative structure-activity relationship (QSAR) model is adopted to study the relationship between the chemical and physical properties of various substances and the structure. Through QSAR studies, the internal relationship between the invisible structure and the activity can be obtained. In this paper, a novel chaos-enhanced accelerate particle swarm algorithm (CAPSO) is proposed, which is used to molecular descriptors screening and optimization of the weights of back propagation artificial neural network (BP ANN). Then, the QSAR model based on CAPSO and BP ANN is put forward, hereinafter referred to as CAPSO BP ANN model. The prediction experiment showed that the CAPSO algorithm is a reliable method for screening molecular descriptors and the five molecular descriptors obtained by CAPSO algorithm could well characterize the molecular structure of each compound in pKa prediction. The experimental results also showed the CAPSO BP ANN model has a good performance in predicting the pKa values of various compounds, the absolute mean relative error, root mean square error, and square correlation coefficient are respectively 0.5364, 0.0632, and 0.9438, indicating the higher prediction accuracy and correlation. The proposed hybrid intelligent model can be applied in all kinds of engineering design, prediction of physical and chemical properties and intelligent calculation.

By reinterpreting the calibration of structural models, a reassessment of the importance of the input variables is undertaken. The analysis shows that volatility is the key parameter to any calibration exercise by several orders of magnitude. In order to maximize the sensitivity to volatility, a simple formulation of Merton’s model is proposed that employs deep out-of-the-money option implied volatilities. The methodology also eliminates the use of historic data to specify the default barrier thereby leading to a full risk neutral calibration. Subsequently, a new technique for identifying and hedging capital structure arbitrage opportunities is illustrated. The approach seeks to hedge the volatility risk, or vega, as opposed to the exposure from the underlying equity itself, or delta. The results question the efficacy of the common arbitrage strategy of only executing the delta hedge.

Over 2.2 billion people across the globe face significant barriers to accessing essential ophthalmic care, with elderly, rural, and refugee populations being disproportionately affected. These obsta-cles deepen existing disparities in eye care. 3D printing is a novel technology that has the potential to transform the field and improve access through alleviating many patient-specific barriers. This article delves into the evolution of 3D printing within ophthalmology, highlighting its current ap-plications and future potential. It explores various 3D printing techniques and biomaterials, dis-cussing their effectiveness in creating advanced solutions such as bioengineered corneas, ocular prosthetics, and innovative treatments for dry eye syndrome. Additionally, 3D printing has rev-olutionized drug delivery systems for conditions like glaucoma, retinal diseases, and for ocular brachytherapy. Despite its promise, the integration of 3D printing into clinical practice presents challenges, which the article addresses alongside strategies for overcoming them. By mapping out the technological advancements and challenges, this review offers a roadmap for enhancing global eye care accessibility and improving patient outcomes on a global scale.

The ACEtabular rim eXtension (ACE-X) implant is a custom-made 3-dimensional-printed titanium device designed for the treatment of canine hip dysplasia. Thirty-four dogs (61 hips) underwent ACE-X implantation, and assessments were conducted using computed tomography, force plate analysis, Ortolani’s test, and Helsinki Chronic Pain Index (HCPI) questionnaires at five intervals: pre-operative day, surgery day, 1.5-month, 3-month, and 12-month follow-up. Statistically significant increases in femoral head coverage with negative Ortolani subluxation test were observed immediately after surgery and persisted throughout the study. Osteoarthritis (OA) scores remained stable, but osteophyte size significantly increased between the surgery day and the 12-month follow-up, especially in hips with a baseline OA score of 2 compared to those with a score of 1. Force plate data showed no significant changes during the study. The HCPI demonstrated a significant decrease in pain score from pre-operative value to 6-week follow-up and gradually decreased over time. Major complications were identified in 6 hips (9.8%) of 4 dogs. In conclusion, the ACE-X implant effectively increased femoral head coverage, eliminated subluxation, and provided long-term pain relief with minimal complications, benefiting over 90% of the study population. The study supports the ACE-X implant as a secure and valuable treatment for canine hip dysplasia.

Due to the manufacturing process of Additive Manufacturing (AM) Parts the mechanical properties cannot be predicted. The scope of the present work is to propose a predictive tool for the mechanical properties of AM parts through the use of Adaptive Neuro-Fuzzy Inference System (ANFIS). The Adaptive Neuro-Fuzzy Inference System (ANFIS) combines neural networks with fuzzy logic to generate a mapping between the inputs and the output. Real data experiments from different AM technologies and materials compose the initial dataset so a detailed investigation is conducted to gain knowledge of how different parameters affect the UTS, the elongation and the Young modulus of each experiment. Experimental data were also use to train, check and verify the methodology. The method is tested for FFF technology, PLA material and 3 point bending stress, with interesting results.

This study aims to demonstrate the possibility of incorporating a natural antioxidant biomolecule, into polymeric porous scaffolds. To this end, Poly-L-Lactic Acid (PLLA) scaffolds were produced using the Thermally Induced Phase Separation (TIPS) technique and additivated with different amounts of Rosmarinic Acid (RA). The scaffolds, with a diameter of 4 mm and a thickness of 2 mm, were characterized with a multi-analytical approach. Specifically, Scanning Electron Mi-croscopy analyses demonstrated the presence of an interconnected porous network, character-ized by a layer of RA at the level of the pore’s surfaces. Moreover, the presence of RA biomole-cules increased the hydrophilic nature of the sample, as evidenced by the decrease in contact angle with water from 128° to 76°. This approach is cost-effective, and it could be customized with different biomolecules, offering the possibility of producing porous polymeric structures con-taining antioxidant molecules. These scaffolds meet the requirements of tissue engineering and could be offered a potential solution to reduce inflammation associated with scaffold implantation thus improving tissue regeneration.

The pharmaceutical industry usually utilizes either hydrophobic or hydrophilic substances extracted from raw plant materials for preparing a final product, However, the plant material waste still contain substances with an opposite solubility. The aim of this study was to enhance the comprehensive usability of plant materials by developing a new non-wasting extraction method for eucalypt leaves and by investigating the phytochemical and pharmacological properties of eucalypt extracts and their 3D-printed dosage forms. The present extraction method enabled to prepare both hydrophobic soft extracts and hydrophilic (aqueous) dry extracts. We identified total 28 terpenes in the hydrophobic soft extract. In the hydrophilic dry extract, total 57 substances were identified, and 26 of them were successfully isolated. The eucalypt extracts studied showed a significant antimicrobial activity against Staphylococcus aureus, Pseudomonas aeruginosa, Bacillus subtilis, Candida albicans, Corynebacterium diphtheriae gravis, and Corynebacterium diphtheriae mitis. The anti-inflammatory activity of the dry extract was studied with a formalin oedema model in mice. The maximum anti-exudative effect of the dry extract was 61.5% at a dose of 20 mg/kg. The composite gels of polyethylene oxide and eucalypt extract were developed, and the key process parameters for semi-solid extrusion (SSE) 3D printing of such gels were verified. The SSE 3D-printed preparations of novel synergistically acting eucalypt extracts could have uses in antimicrobial and anti-inflammatory medicinal applications.

The first paper of this two-part series paper discussed the development of a novel lightweight 3D wood dowel-reinforced glass epoxy hybrid composite material (3DdrFRP) and its manufacturing procedures. It also experimentally compared the performance of scaled utility poles made from conventional 2D E-glass epoxy and 3DdrFRP materials. In the second part, we developed robust finite element (FE) models in LS-DYNA, calibrated them based on experimental results, and used them to simulate the performance of equivalent 2D and 3D poles, proving the integrity of the numerical model. Additionally, we developed a simplified analytical calculation method for engi-neers to determine the stiffness of 3D-DrFRP poles accurately and quickly.

The most modern technique utilized to create intricate and complexly manufactured parts for a variety of applications is called additive manufacturing (AM). Fused deposition modeling (FDM) has received the greatest attention in the development and manufacturing sectors. The main objective of this study was to investigate how printing factors affected the mechanical characteristics of printed samples. Samples were produced using an FDM 3D printer in compliance with ASTM D638 using a variety of input settings, including orientation, layer thickness, speed, and infill pattern. On the printed samples, tensile tests and morphological analysis using a scanning electron microscope (SEM) were done. The findings of this study demonstrate that factors including layer thickness, printing speed, and orientation significantly affect the tensile strength of ABS printed samples. Discovering the process settings that could lead to superior mechanical and physical characteristics would undoubtedly assist designers and manufacturers worldwide as the FDM 3D printer becomes more and more crucial in manufacturing engineering parts.

The expression of the Fasciola hepatica Carboxylesterase type B (CestB) gene is induced in response to the anthelmintic triclabendazole (TCBZ), resulting in a significant increase in enzymatic specific activity. Furthermore, the amino acid sequence of CestB exhibits variations that could lead to substantial amino acid substitutions at the ligand-binding site. These substitutions have the potential to affect the interaction between the ligand and the protein, as well as the catalytic properties of the enzyme. The objective of this study was to identify new CestB polymorphisms in TCBZ-resistant parasites using 3D modeling against the metabolically oxidized form of the anthelmintic TCBZSOX. Our aim was to observe the formation of TCBZSOX-specific binding pockets that could potentially explain the resistance to anthelmintic agents. We identified a CestB polymorphism in a TCBZ-resistant strain of parasites exhibiting three radical amino acid substitutions at positions 147, 215, and 243, resulting in the formation of a TCBZSOX-affinity pocket capable of binding the anthelmintic drug. Additionally, our 3D modeling analysis revealed that these amino acid substitutions also had an impact on the configuration of the CestB catalytic site, affecting the enzyme's interaction with chromogenic carboxylic ester substrates and altering its catalytic properties; however, the identified TCBZSOX-binding pocket was located far from the enzyme's catalytic site, making the enzymatic hydrolysis of TCBZSOX theoretically impossible. Nonetheless, the increased affinity for the anthelmintic may explain a drug-sequestration type of anthelmintic resistance and lays the foundation for the development of a molecular diagnostic tool for identifying anthelmintic resistance in F. hepatica.

This comprehensive review explores the advancements in Orthognathic and Oral Maxillofacial Surgery, focusing on the integration of 3D Printing and Virtual Surgical Planning (VSP). Traditional surgical methods, while effective, come with inherent risks and complications, and can lead to variability in outcomes due to the reliance on the surgeon's skill and experience. The shift towards patient-centric care necessitates personalized surgical methods, which can be achieved through advanced technology. The amalgamation of 3D printing and VSP revolutionizes surgical planning and implementation by providing tactile 3D models for visualization and planning, and accurately designed surgical guides for execution. This convergence of digital planning and physical modeling facilitates a more predictable, personalized, and precise surgical process. However, the adoption of these technologies presents challenges, including the need for extensive software training and the steep learning curve associated with computer-aided design programs. Despite these challenges, the integration of 3D printing and VSP paves the way for advanced patient care in orthognathic and oral maxillofacial surgery.

In the present work, a comparative evaluation of an MBBR unit performance was carried out for the following cases: when adding 3D-printed biocarriers fabricated with 13X and bentonite, when using K1 commercial biocarriers and when not adding biocarriers at all. For the evaluation of the MBBR efficiency, various physicochemical parameters were measured, while static light scattering and optical microscopy observations were additionally used. Finally, biofilm extracted from the biocarriers was evaluated. The findings suggest that there is an optimal biodegradation of the organic load in all MBBR units. The nitrification and denitrification process were improved at the 3D MBBR as compared to the control MBBR and MBBR K1. The dry mass of the biofilm in the 3D-printed biocarriers was two orders of magnitude larger than the one in the K1 biocarriers. What is more, in the K1 biocarriers the mass of the biofilm varied in relation to time, due to the fact that it could not be kept inside the holes, something that was not observed to happen with the 3D-printed biocarriers. Finally, it was observed, mostly in the 3D MBBR and less in the K1 MBBR, that the growth of nitrifying bacteria and heterotrophs inside the units increased the biomass production in the form of SMP, which in turn favored the adhesion of biomass on the surface of biocarriers.

The first years of an infant’s life represent a sensitive period for neurodevelopment and see the emergence of nascent forms of executive function (EF), which are required to support complex cognition. Few tests exist for measuring EF during infancy, and the available tests require painstaking manual coding of infant behaviour. In modern clinical and research practice, human coders collect data on EF performance by manually labelling video recordings of infant behaviour during toy or social interaction. Besides being extremely time-consuming, video annotation is known to be rater-dependent and subjective. To address these issues, starting from existing cognitive flexibility research protocols, we developed instrumented toys as a new task instrumentation and data collection tool suitable for infant use. A commercially available device comprising a Barometer and Inertial Measurement Unit (IMU) embedded in a 3D-printed lattice structure was used to detect when and how the infant interacts with the toy. The data collected using the instrumented toys provides a rich dataset describing the sequence of toy interaction and individual toy interaction patterns, from which EF-relevant aspects of infant cognition may be inferred. Such a tool potentially provides an objective, reliable, and scalable method of collecting early developmental data in socially interactive contexts.

Phase imaging of biochemical samples has been demonstrated for the first time at the Infrared Microspectroscopy (IRM) beamline of the Australian Synchrotron using the usually discarded Near-IR (NIR) region of the synchrotron-IR beam. The synchrotron-IR beam at the Australian Synchrotron IRM beamline has a unique fork shaped intensity distribution as a result of the gold coated extraction mirror shape, which includes a central slit for rejection of the intense X-ray beam. The resulting beam configuration makes any imaging task challenging. For intensity imaging, the fork shaped beam is usually tightly focused to a point on the sample plane followed by a pixel-by-pixel scanning approach to record the image. In this study, a pinhole was aligned with one of the lobes of the fork shaped beam and the Airy diffraction pattern was used to illuminate biochemical samples. The diffracted light from the samples was captured using a NIR sensitive lensless camera. A rapid phase-retrieval algorithm was applied to the recorded intensity distributions to reconstruct the phase information corresponding to different planes. The preliminary results are promising to develop multimodal imaging capabilities at the IRM beamline of the Australian Synchrotron.

Based on the historical research on the shape of armor in Ming Dynasty, this paper explores the shape characteristics of general armor in Ming Dynasty in China through field research on the general stone statue of Ming Xiaoling Mausoleum in Nanjing. Through Ming Xiaoling Mausoleum general stone carving 3D animation technology restoration project, virtual material heritage practice is carried out. Through the modeling of the general stone statue in Ming Xiaoling Mausoleum by MAYA and Zbrush, UE4 realizes the construction of scenes and the output of interactive effects, so as to explore a mode of application engine animation that can preserve and propagate general stone carving in Ming Xiaoling Mausoleum.

This article presents, for the first time, the kinetics and the general conversion features of a 3-component system, BT(BC)/iodonium/Amine, based on proposed mechanism of Liu et al, for both free radical polymerization (FRP) of acrylates and the free radical promoted cationic polymerization (CP) of epoxides using the new multi-functional initiator of benzophenone–triphenylamine (BT). The additives, iodonium and EDB, have the dual function of (i) regeneration BT and (ii) produce of extra radicals for improved FRP and CP. Analytic formulas are developed to explore the new features including: (i) the conversion efficacy (CE) of FRP is an increasing function of the light intensity, the effective absorption coefficient, and the concentration sum of each of the components, BT, Iod, amine, for transient state. However, CE at steady-state is independent to the light intensity; (ii) the trifunctional hybrid structures of BT3 leads to larger light absorption than other types of BT; it also provides more active sites for the H-abstraction in the presence of EDB, leading to high CE; (iii) the efficacy of FRP is an increasing function of the amine (EDB) concentration, in contrast to that of CP having an opposite dependence; (iv) the consumption rate of BT3 in the BT3/ Iod/EDB system is slower than that of the BT3/Iod system due to photoredox catalytic cycle, and the larger initiator regeneration (RGE)
in the three-component system. A comprehensive model is also proposed that the CE (for both FRP and CP) is governed by (N_jK_jbI), whereas more complex formulas are developed; where Kj is an effective rate constant proportional to the electron transfer quantum yield, and the combined effects of other coupling rate constants; b is an effective absorption coefficient given by the light absorption and excited state quantum yield.

This study explores the potential to reach a circular economy for post-consumer recycled polyethylene terephthalate (rPET) packaging and bottles by using it as a distributed recycling for additive manufacturing (DRAM) feedstock. Specifically, rPET is processed using only an open source toolchain with fused particle fabrication (FPF) or fused granular fabrication (FGF) processing. In this study, first the impact of granulation, sifting and heating (and their combination) is quantified on the shape and size distribution of the rPET flakes. Then feeding studies were performed to see if they could be printed through an external feeder or needed to be direct printed with a hopper using two Gigabot X machines, one with extended part cooling and one without. Print settings were optimized based on thermal characterization and for the latter which was shown to print rPET directly from shredded water bottles mechanical testing is performed. The results showed that geometry was important for extended feeding tubes and direct printed using a hopper. Further there is a wide disparity in the physical properties of rPET from water bottles depending on source and the history of the material. Future work is needed to enable water bottles to be used as a widespread DRAM feedstock.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

The tumor organoid (tumoroid) model in three-dimensional (3D) culture systems has been developed to reflect more closely the in vivo tumors than 2D-cultured tumor cells. Notably, extracellular vesicles (EVs) are efficiently collectible from the culture supernatant of gel-free tumoroids. Matrix metalloproteinase (MMP) 3 is a multi-functional factor playing crucial roles in tumor progression. However, roles of MMP3 within tumor growth and EVs have not unveiled. Here, we investigated the protumorigenic roles of MMP3 on integrities of tumoroids and EVs. We generated MMP3-knockout (KO) cells using the CRISPR/Cas9 system from rapidly metastatic LuM1 tumor cells. Moreover, we established fluorescent cell lines with palmitoylation signal-fused fluorescent proteins (tdTomato and enhanced GFP). Then we confirmed the exchange of EVs between cellular populations and tumoroids. LuM1-tumoroids released large EVs (300-1000 nm) and small EVs (50-200 nm) while the knockout of MMP3 resulted in the additional release of broken EVs from tumoroids. The loss of MMP3 leads to a significant reduction in tumoroid size and to the development of the necrotic area within tumoroids. MMP3 and CD9 (a category-1 EV marker tetraspanin protein) were significantly down-regulated in MMP3-KO cells and their EV fraction. These weakened phenotypes by MMP3 KO were markedly rescued by the addition of MMP3-rich EVs or conditioned medium (CM) collected from LuM1-tumoroids, which caused a dramatic rise in the expression of MMP3, CD9, and Ki-67 (a marker of proliferating cells) in the MMP3-null/CD9-low tumoroids. Notably, MMP3 enriched in tumoroids-derived EVs and CM deeply penetrated into recipient MMP3-KO tumoroids, resulting in a remarkable enlargement of solid tumoroids, while MMP3-null EVs did not. These data demonstrate that EVs can mediate molecular transfer of MMP3 resulting in increasing the proliferation and CD9+ tumorigenesis, indicating crucial roles of MMP3 in tumor progression.

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

Radio-fluorogenic (RFG) gels become permanently fluorescent when exposed to high-energy radiation with the intensity of the emission proportional to the local dose of radiation absorbed. An apparatus is described, FluoroTome 1, that is capable of taking a series of tomographic images (thin slices) of the fluorescence of such an irradiated RFG gel on-site and within minutes of radiation exposure. These images can then be compiled to construct a 3D movie of the dose distribution within the gel. The historical development via a laboratory-bench prototype to a readily transportable, user-friendly apparatus is described. Instrumental details and performance tests are presented.

This article proposes the use of a multi-scale and multi-sensor approach to collect and modelling 3D data concerning wide and complex areas in order to obtain a variety of metric information in the same 3D archive, based on a single coordinate system. The employment of these 3D georeferenced products is multifaceted and the fusion or integration among different sensors data, scales and resolutions is promising and could be useful for the generation of a model that could be defined as hybrid. The correct geometry, accuracy, radiometry and weight of the data models are hereby evaluated comparing integrated processes and results from Terrestrial Laser Scanner (TLS), Mobile Mapping System (MMS), Unmanned Aerial Vehicle (UAV), terrestrial photogrammetry, using Total Station (TS) and Global Navigation Satellite System (GNSS) as topographic survey. The entire analysis underlines the potentiality of the integration and fusion of different solutions and is a crucial part of the “Torino 1911” project whose main purpose is mapping and virtually reconstructing the 1911 Great Exhibition settled in the Valentino Park in Turin (Italy).

Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

In this article, we introduce a new approach to human movement by defining the movement as a static object or a super object in one two-dimensional image. This method can allow researchers to label and describe the total movement as an object isolated from a reference video. This ap-proach allows us to perform various tasks, including finding similar movements in a video, measuring, and comparing movements, generating new similar movements, and defining chore-ography by controlling specific parameters in the human body skeleton. As a result of the pre-sented approach, we can eliminate the need to label images manually, disregard the problem of finding the beginning and the end of a movement, overcome synchronization issues between movements, and perform any deep learning network-based operation that processes super objects in images in general. As part of this article, we will demonstrate two application use cases: one il-lustrates how to verify and score a requested movement. In contrast, the other illustrates how to generate similar movements in the human skeleton space by addressing the challenge of supply-ing sufficient training data for deep learning applications (DL). A Variational Auto Encoder (VAE) simulator and an EfficientNet-B7 classifier architecture embedded within a Siamese twin neural network are presented in this paper in order to demonstrate two use cases. These use cases demonstrated the versatility of our innovative concept in measuring, categorizing, inferring hu-man behavior, and generating gestures for other researchers.

This study investigates the process of multi-walled carbon nanotube (MWCNT) coatings to enhance the lamp heating temperature for solar thermal absorption applications. The primary focus is studying the effects of self-organized honeycomb structures of CNTs formed on silicon substrates on different cell area ratios (CAR). The drop-casting process developed honeycomb-structured MWCNT-coated absorbers with varying CAR values ranging from ~ 60% to 17%. The optical properties were investigated within the visible (400-800 nm) and near-infrared (934-1651nm) wavelength ranges. Although fully coated MWCNT absorbers showed the lowest reflectance, honeycomb structures with a ~ 17% CAR achieved high-temperature absorption. These structures maintained 8.4% reflectance at 550 nm while dramatically increasing infrared reflection to 80.5% at 1321 nm. The performance of solar thermal was assessed throughout a range of irradiance intensities, from 0.04 W/cm² to 0.39 W/cm². The honeycomb structure with a ~17% CAR value consistently performed better than other structures by reaching the highest absorption temperatures (ranging from 52.5°C to 285.5°C) across all measured intensities. A direct correlation was observed between the reflection ratio (visible: 550 nm / infrared: 1321 nm) and temperature absorption efficiency, where lower reflection ratios were associated with higher temperature absorption. This study highlights the significant potential for the large-scale production of cost-effective solar thermal absorbers through the application of optimized honeycomb-structured absorbers coated with MWCNTs. These contributions enhance solar energy efficiency for applications in water heating and purification, thereby promoting sustainable development.

Rhizosphere microorganisms can utilize nutrient resources in the rhizosphere efficiently, while rhizosphere growth-promoting bacteria play a crucial role in regulating soil fertility and promoting plant health. In this study, we employed a combination of isolation, purification, identification of dominant microorganisms, and high-throughput sequencing technology to analyze the main microbial groups and diversity in the rhizosphere soil of Helichrysum arenarium（L.）Moench. in Altay, Xinjiang，China. By isolating bacterial strains from the rhizosphere soil using a dilution coating method, we successfully obtained 43 strains. Subsequently, selective medium was utilized to screen for growth-promoting characteristics among these isolated strains from the rhizosphere soil of H. arenarium（L.）Moench.. The results obtained through high-throughput amplification sequencing revealed that the rhizosphere soil harbored diverse bacterial communities belonging to 35 phyla, 93 orders, 215 families, 324 genera and 231 species associated with H. arenarium（L.）Moench., as well as fungal communities consisting of 14 phyla ,47 orders ,96 families ,204 genera and 571 species. Among these bacterial communities identified, eight phyla exhibited relative abundances exceeding 1%, with Actinobacteriota being most predominant at an abundance rate of 41.30%. Additionally,five bacterial genera were found to have relative abundances exceeding 1% ,with Arenimicrobium_luteum being most abundant at 6.11% . Furthermore,four fungal phyla displayed relative abundances surpassing1 % ,with Ascomycota accounting for 67.21% of total fungal community composition.Finally,four fungal genera demonstrated relative abundances higher than 1% ,with Knufia representing 3.80% of total fungal community composition.The analysis on culturable bacteria's promotion activity within the rhizospheric soil indicated that two strains,S16and S29, exhibited the highest solubility index for inorganic phosphorus. However, it lacked the ability to dissolve organophosphorus and potassium. On the other hand, strains S7 and S10, which were screened, demonstrated nitrogen-fixing capabilities. Nine strains with excellent iron-bearing capacity were identified, with strain S16 exhibiting the highest D/d value and strongest iron-bearing capacity among them. Our findings revealed that 43 rhizosphere soil bacteria belonged to three genera. The ten growth-promoting bacteria were identified as Kocuria rosea, Priestia megaterium, Bacillus mobilis, B. bataviensis, B. mycoides (two strains), B. paramobilis, and Alcaligenes faecalis. This study provides a particular research basis for the influence of H. arenarium（L.）Moench. rhizosphere microorganisms on soil nutrient release and depicts a solution for improving the yield and quality cultivation of H. arenarium（L.）Moench. by isolating, screening, and identifying rhizosphere soil growth-promoting bacteria, including screening strains with growth-promoting functions and analyzing the population structure of rhizosphere and habitat soil in combination with high-throughput sequencing technology.

This study primarily investigates the effect of fly ash (FA) content on the mechanical properties and hydration performance of alkali-activated ground granulated blast furnace slag cements (AAGC), and compares the related properties with ordinary Portland cement (OPC). Additionally, the study examined the hydration products, thermal analysis, MIP, SEM, chemically bound water, and pH values of AAGC. The compressive strength of AAGC showed a retrogression phenomenon from 3 to 28 days, with the 14-day and 28-day compressive strengths of AAGC being higher than those of OPC. The AAGC with 20% FA content exhibits the highest 28-day compressive strength (75 MPa). The hydration heat release rate curved of OPC and AAGC can be divided into the initial induction period, induction period, acceleration period, deceleration period and steady period. As FA content increases, the 28-day pore volume of AAGC increased while pH values and chemically bound water decrease. SEM images of AAGC with low FA content showed more microcracks.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

In this article we have constructed a basic methodology from which important perspectives for both the Collatz conjecture and Beal's conjecture can be derived. We falsified the conjecture we previously developed on Beal's conjecture and made the falsified conjecture usable for Collatz conjecture. In this regard, we have clearly expressed the numbers that can reach 1 in the Collatz conjecture. Then, using this, we created a limit for the numbers that should be considered for the Collatz conjecture. Thanks to the analysis of this limit, we have clearly expressed the recursive Collatz function in an equation. Using this structure, we wrote a function that indicates how many times the Collatz function repeats certain numbers to reach 1.

Porous hierarchical structure has been widely used in engineering for its high specific strength and stiffness, improved corrosion-resistance and multifunctionality. The design of multi-scale topology optimization for such structures has been a hot topic during the past two decades. In this paper, a new hybrid MMC-density topology optimization method of cellular structures with quasi-periodic microstructures is proposed. The so-called ‘quasi-periodic’ means the microstructures in different macro points have similar topology but with different parameters. The key idea is to describe the microstructural topology using MMC and describe the micro layout using the variable density. Sensitivities of the structural compliance with respect to the two types of design variables are derived and gradient optimization method is applied to update the design variables. The presented numerical examples show that the quasi-periodic cellular structures have better performance than single-scale structures and periodic cellular structures. Numerical examples demonstrate the effectiveness of the proposed approach.

Healthcare leaders are faced with many financial challenges in the contemporary environment, leading to many bankruptcies in recent years. What is not well understood are the specific conditions that lead to organizational economic failure. Ideally, hospital leaders could examine the literature for guidance to predict bankruptcy before it occurs. However, existing regression methods have proven inadequate, especially when the finance variables follow a nonnormal frequency pattern. Furthermore, the regression approach encounters difficulties due to multicollinearity and nonnormality issues. Therefore, an alternate stochastic approach for predicting the probability of hospital bankruptcy is warranted. This new method includes computing and interpreting the correlations between the hospital’s revenue and expenses for bivariate lognormal data, calculating the risk of bankruptcy due to the mismatch between revenues and expenses, determining the likelihood of a hospital’s expense exceeding the state’s median expense level, and evaluating a hospital’s financial memory level. Ultimately in our research, we demonstrate a novel approach to anticipate hospital bankruptcy, which can be particularly useful for health policy analysts and hospital leaders in making informed financial decisions and proactively managing risks to ensure the sustainability and stability of their institutions.

The superfamily of Acid proteases has two catalytic aspartates for proteolysis of their peptide substrates. Here, we show a minimal structural scaffold, the Structural Catalytic Core (SCC), which packs all conserved substructure elements around the catalytic machinery, and which can be found in all enzymes of the Acid proteases superfamily. The SCC is a dimer of several structural blocks, such as the DD-link, the D-loop and the G-loop, around two catalytic aspartates in each protease subunit or within an individual chain. The dimer of two D-loop/DD-link substructures makes a DD-zone, and the dimer of two D-loop/G-loop substructures makes a psi-loop. These structural markers are useful for protein comparison, structure identification, protein family separation and protein engineering.

Although promoting healthy eating is a policy objective, the controllability of dietary habits remains uncertain. The personal dietary patterns reflect many factors, of which some are relatively controllable for individual, and others are not. In this article, assuming that some sort of information about controllability of dietary habits is contained in the observed pattern of food consumptions, we focused on dietary pattern on its own. We introduced a statistical descriptive model for data on food frequency questionnaire, estimated strength of pairwise linkage between foodstuffs, and grouped foodstuffs by applying community detection to the networks of the estimated inter-food linkages. Those linkages represent co-movement of pairs of foods consumption. Furthermore, we demonstrated an analysis on the relationship between health of mind and dietary habits considering the aspect of controllability of dietary habits. Using an observational study in Japan, we obtained the following results: 115 foodstuffs were divided into 3 groups for both of genders, but the compositions were different by gender; in the analysis of mental health, some stress response items were associated with the dependence on some of those food groupings. As the grouping of foodstuffs based on our estimation depicted the internal structure of dietary habit that a healthy eating policy should regard as constraint, it follows that we should design the policy along the line with that grouping.

In this study, a new diphosphate compound, Ag0.2Na0.6FeP2O7, was synthesized using a solid-state reaction method and extensively studied using various techniques. The compound's structure was confirmed through X-ray diffraction analysis, revealing a single-phase monoclinic structure with the P21/C space group. The electrical behavior of the compound was investigated, and its conductivity followed Jonscher's universal law. The correlated barrier hopping (CBH) model explained the temperature-dependent ac conductivity and parameter "s" well. The study also explored the contribution of single-polaron and bipolaron hopping to the a.c. conductivity and discussed the ionic conductivity in relation to the structural characteristics of the sample. Overall, this investigation significantly enhances our comprehension of the distinctive electrical properties of Ag0.2Na0.6FeP2O7 and its potential practical applications.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

RAMOSA1 (RA1) is a Cys2-His2-type (C2H2) zinc finger transcription factor that controls plant meristem fate and identity and has played an important role in maize domestication. Despite its importance, the origin of RA1 is unknown and the evolution in plants is partially understood. In this paper, we present a well resolved phylogeny based on 73 amino acid sequences from 48 embryophyte species. The recovered tree topology indicates that, during grass evolution, RA1 arose from two consecutive SUPERMAN duplications resulting in three distinct grass sequence lineages: RA1-like A, RA1-like B, and RA1; however, most of these copies have unknown functions. Our findings indicate that RA1 and RA1-like play roles in the nucleus despite lacking a traditional nuclear localization signal. Here we report that copies diversified their coding region and, with it, their protein structure, suggesting different patterns of DNA binding and protein-protein interaction. In addition, each of the retained copies diversified regulatory elements along their promoter regions, indicating differences in their upstream regulation. Taken together, we propose that the RA1 and RA1-like gene families in grasses may have undergone subfunctionalization and neofunctionalization enabled by gene duplication.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

Abstract Introduction: Poor structural quality of health facilities for tuberculosis (TB) diagnosis and treatment contributes to unfavorable health outcomes among TB patients. Improving the quality of healthcare services helps to avert TB-related morbidity. Despite these facts, the level of structural quality of health facilitieSs to deliver TB services is not in line with what the national TB and leprosy program (NTLP) recommends. Hence, the present study was conducted to assess the structural quality of health facilities to deliver quality TB services to TB patients among public health facilities in the Sidama region.Objectives: To determine the quality of the structural domain of TB services at public health facilities in the Sidama region of southern Ethiopia.Methods: An institution-based cross-sectional study was conducted from June to July 2023 among randomly selected public health facilities in the Sidama region. We included 40 randomly selected public health facilities that delivered TB services in the study area. Data was collected by experienced data collectors using facility audits, clinical observation checklists, structured questionnaires, and in-depth interviews. An Open Kit Mobile (ODK) application was used to collect data and exported to SPSS version 26. All statistical analysis was done using SPSS version 26.Results: The overall mean quality score for the structural dimension was 50.25 among the 40 health facilities audited in the study area.Conclusion: The quality of TB services regarding structural dimensions was poor in the study area. Therefore, any strategies must give careful attention to increasing the comprehensive structural dimension of quality TB services.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

Research on titanium oxo complexes (TOCs) are usually focused on their structure and photocatalytic properties. Findings from these investigations spurred our interest in exploring also their potential biological activities. In this study, we focused on the synthesis and structure of a compound with the general formula [Ti8O2(OiPr)20(man)4] (1), which was isolated from the reaction mixture of titanium(IV) isopropoxide with mandelic acid (Hman) in a molar ratio of 4:1. The structure (1) was determined using single-crystal X-ray diffraction, while spectroscopic studies provided insights into its physicochemical properties. To assess the potential practical applications of (1), its microcrystals were incorporated into a polymethyl methacrylate (PMMA) matrix, yielding composite materials of the type PMMA + (1) (2 wt.%, 5 wt.%, 10 wt.%, and 20 wt.%). The next stage of our research involved the antimicrobial activity evaluation of the obtained materials. Investigations carried out demonstrated antimicrobial activity of pure (1) and its composites (PMMA + (1)) against both Gram-positive and Gram-negative strains. Furthermore, MTT tests conducted on the L929 murine fibroblast cell line confirmed the lack of cytotoxicity of these composites. Our study identified (1) as a promising antimicrobial agent, also for producing composite coatings.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Because data on the fungal gut community structure of African children are scarce, we aimed to describe by reanalysing rRNA ITS1 and ITS2metabarcoding data from a study designed to assess the influence of microbiota in malaria susceptibility in Malian children from the Dogon country. More specifically, we aimed to establish the core gut mycobiome and compare the gut fungal community structure of breastfed children, aged 0-2 years, with other age groups. Briefly, DNA was extracted from 296 children’s stool samples. Both rRNA ITS1 and ITS2 genomic barcodes were amplified and subjected to Illumina MiSeq sequencing. The ITS2 barcode generated 1,975,320 reads and 532 operational taxonomic units (OTUs), while the ITS1 barcode generated 647,816 reads and 532 OTUs. The alpha diversity was significantly higher by using the ITS1 compared to the ITS2 barcode (p

The dimethylaminophenyl-substituted silver phthalocyanine [dmaphPcAg] can be used as a UV-vis photoinitiator for in situ preparation of a silver/polymer nanocomposite. To verify early steps of the supposed mechanism of radical polymerization, we performed quantum chemical calculations of m[dmaphPcAg]q complexes with charges q = +1 to -2 in the two lowest spin states m, of a free ligand and its dehydrogenated/deprotonated products m[dmaphPcHn]q, n = 2 to 0, q= 0, -1 or -2, in the lowest spin states m. The calculated electronic structures and electron transitions of all the optimized structures in CHCl3 solutions are compared with experimental EPR and UV-vis spectra, respectively. The unstable 3[dmaphPcAg]+ species deduced only from previous EPR spin trap experiments was identified. In addition to 2[dmaphPcAg]0, our results suggest the coexistence of both reaction intermediates 1[dmaphPcAg]- and 3[dmaphPcAg]- in reaction solutions. Silver nanoparticle formation is a weak point of the supposed reaction mechanism from the energetic, stereochemistry, and electronic structure points of view.

A survey of the trends in metal-ligand coordination and hydrogen bonding has been carried out on complexes of singly deprotonated cyanuric acid CY− and alkaline earth metals, synthesised from aqueous solution and characterised by X-ray crystallography. Involvement of cyanurate in the metal coordination increases from Mg through Ca and Sr to Ba relative to coordination by water, in parallel with the increasing ionic radius and coordination number. The incidence of bridging of metal centres by both water and cyanurate also increases in this series. The Mg complex contains hexaaqua-coordinated cations, uncoordinated CY− anions, and additional water molecules. Ca and Sr complexes feature polymeric chains of coordinated metal ions, the Ca complex with uncoordinated anions and the Sr complex with all potential ligands coordinated. The Ba complex has a two-dimensional coordination network. Extensive hydrogen bonding plays a key role in generating a three-dimensional network in all four structures. The competition between cyanurate and water for coordination to the alkaline earth metal cations, and that between coordination and hydrogen bonding propensities of the cyanurate anion, appear to be finely balanced, with the structural outcomes depending on the relative sizes and degrees of hardness of the four cations of the group.

This study aimed to increase the energy independence of buildings by utilizing solar energy to produce renewable energy. The subject of this study was a shading structure installed in an outdoor space to provide solar energy. Solar panels were applied to the shaded structures to generate energy actively. The solar panels were designed to be moved according to the optimal tilt angle each month to produce the optimal renewable energy. The architectural design of the shading structure and the energy simulation of the solar panels were conducted using a parametric design. The results of the energy simulation showed the generation of 31,570 kWh· year−1 of renewable energy. This amount of energy is 10% higher than that produced by fixed solar panels. Thus, the moving solar panel system developed in this study not only increases the energy independence of buildings, but also has the advantage of higher renewable energy production compared with fixed solar panels. Additionally, various types of shading structures can be designed depending on the combination of solar panel modules; in particular, moving solar panels have the potential to facilitate ecofriendly designs when applied to the exterior of buildings.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

The expedited development of drugs targeting gene products associated with insulin resistance holds the potential to enhance our comprehension of type 2 diabetes mellitus (T2DM). The virtual screening based on a three-dimensional (3D) protein structure has been expected as potential technique to accelerate a development of molecular target drugs. Among the targets implicated in insulin resistance, genetic characterization and protein function of Grb14 have been clarified without contradiction. The Grb14 gene displays notable variations in T2DM, and its gene product known to inhibit the function of the insulin receptor (IR) by directly binding to the tyrosine kinase domain. In the present study, a virtual screening, based on 3D structure of IR tyrosine kinase domain (IRβ) in complex with part of Grb14, was conducted to find compounds that can disrupt the complex formation between Grb14 and IRβ. First, ten compounds were selected from 154,118 compounds via hierarchical in silico structure-based drug screening, composed of grid docking-based and genetic algorithm-based programs. The experimental validations suggested that the one compound can affect blood glucose level. The molecular dynamics simulations and co-immunoprecipitation analysis showed that the compound did not completely suppress the protein–protein interaction between Grb14 and IR, though competitively bound to IR with the tyrosine kinase pseudosubstrate region in Grb14.

Public funding of land consolidation projects is an instrument of the Common Agricultural Policy of the European Union (CAP). The execution of systematic land consolidation programmes focused on optimising the spatial structure of agricultural areas presents a possibility to improve agricultural production conditions and maximise the efficiency of agriculture on a local, regional, national and international level. However, due to limited access to financial resources, it is necessary to delimit the priority areas for land consolidation. A contemporary practice based on the assessment of the social support percentage of potential land consolidation projects in individual villages does not represent a real necessity for action. This problem leads to ineffective utilisation of financial resources and reduces the efficiency of the implemented programmes. We proposed a new algorithm for assessing real needs for land consolidation based on a detailed multi-faceted analysis of the spatial structure of agricultural areas. The research method involved factors describing the spatial structure defectiveness of farms as well as those determining land quality in correspondence to investment’s profitability. Another factor verifying the potential economic rationale of land consolidation was transaction prices mostly reflecting the agricultural value of the land. The analysis showed that land consolidation in areas with defective spatial structure and a relatively high market value should be a priority. This approach will contribute to maximising profits by increasing the productivity of areas featuring the highest agricultural suitability.

A mathematical model that comprehensively captures the real behavior of riverbed deformation, encompassing all pertinent effects, is developed. The underwater slope reformation process, with the generatrix aligned along the flow velocity in the model, is considered. A numerical model is introduced to calculate the flow involving a deformable bottom, and the model's validation is established through rigorous analysis of experimental findings. The research firmly confirms the suitability of the proposed mathematical and numerical model for describing deformations in uneven and unsteady river flows, including the movement of dredging slots and channel quarries. The model's minimal equation count and reliance on empirical constants demonstrate the model's efficiency. The model's predictions align strongly with experimental data, although optimal values of empirical coefficients vary slightly across different experiments. Hence, there is a call for further investigation to derive more universally applicable closure relationships for the model. The importance of validating the model with reliable field data and its potential extension to accommodate hydraulically diverse soils is emphasized. Such an extension is feasible due to the concentration transfer equation, enabling independent calculations for particle fractions of varying sizes as long as the total particle concentration in the stream remains within reasonable limits. This dedicated research contributes significantly to understanding riverbed deformations and advancing accurate modeling and management of riverine environments.

Keywords: friction stir processing; additive manufacturing; wire; titanium alloy; material transfer; microstructure; microhardness

In the research we consider a structure-fluid interaction of oscillating piezodevice and acoustic liquid. Such problem requires finding resonance or anti-resonance frequencies of the solid structure to use them in the latter frequency-response analyses step. After finite element discretization of the issue, we need to solve a generalized eigenvalue problem (GEP). The most efficient numerical method for solving the partial GEP is the shift-and-invert Lanczos method. Each step of this algorithm requires solving a large scale system of linear algebraic equations (SLAEs) with special properties. Various ways of ordering grid nodes lead to coefficient matrices with different structure. Several methods are compared in terms of efficiency. The results of the numerical experiments are presented.

With the rapid development of Earth observation and information technology, people are increasingly able to access geospatial models. Geospatial models, based on principles of geography, utilize mathematical, statistical, as well as computer science methods to interpret and predict geographic phenomena. These models can be applied in the fields such as urban planning, environmental protection, traffic management to help decision-makers solve geography-related problems. However, integrating different geospatial models to collaboratively solve complex geographic problems still faces significant obstacles due to heterogeneity in model structure, dependencies, and running modes. In this study, we propose a containerized service-based integration framework for heterogeneous geospatial models (GeoCSIF). GeoCSIF consists of three main components: (1) Model encapsulation. It breaks down complicated geospatial models into independently manageable model units, and builds as unified service packages with a templated constraint method. (2) Model orchestration. It achieves an optimal combination of large-scale models with complex dependencies using a prioritization-based orchestration method. (3) Model publication. It incorporates heuristics into the model scheduling process, which can provide adaptive deployment for different model runs. Finally, a prototype system was developed to validate the effectiveness and progressiveness of GeoCSIF by the integrating process of heterogeneous flood disaster models.

As the general acceptance of fiber-reinforced polymer (FRP) in the concrete construction industry continues to rise, it is increasingly imperative that the crack width of FRP reinforced concrete members of pavement and girder be predicted with good accuracy due to strengthening of RC pavement, slabs or beams structures using FRP is known to control crack width. However, no specific provisions are provided by most international design codes for predicting crack width in FRP reinforced concrete flexure members. In this paper, five formulas for predicting the crack width for FRP reinforced structures are derived from three common computational theories which including statistical method, comprehensive theory, and bond-slip theory. The formula of statistical method is simplest, but the parameters depend on much sample data. The comprehensive and slippage theory based on semi-empirical statistical crack spacing are obtained through the calculation of non-uniformity coefficient of strain. The comprehensive and slippage theory based on semi-empirical axial force balance are obtained through the calculation of tensile reinforcement factor. The comparative analysis of performance of five formulas is carried out. The results indicate that the formula from comprehensive theory based on semi-empirical statistical crack spacing is recommended for predicting the crack width of FRP reinforced concrete flexural structure.

The transferability of structure-property relationships for laser-pretreated metal adhesive joints to laser-pretreated metal – carbon fiber reinforced plastic (CFRP) bonds is investigated. Single-lap shear tests were performed on hybrid AW 6082-T6 – CFRP specimens pretreated with the same pulsed laser surface parameter sets on the metal surface as previously tested AW 6082-T6 – E320 metal adhesive joints. The fracture surfaces were characterized to determine the type of failure and elucidate differences and commonalities in the link between surface structures and single-lap shear strengths. Digital image analyses of the hybrid specimens fractured surfaces were used to quantify remaining CFRP fragments on the metallic joint side. The results indicate that high surface enlargements and the presence of undercut structures leads to single-lap shear strengths exceeding 40 MPa and 35 MPa for unaged and aged hybrid specimens respectively. While for the metal-polymer joints the trend from high strength to weakly bonded specimens was largely continuous with the degree of surface structuring, hybrid metal – CFRP joints exhibit a drastic drop in joint performance after aging if the laser-generated surface structures are less pronounced with low surface enlargements and crater depths. Surface features and hydrothermal aging determine whether the specimens fail cohesively or adhesively.

Graphene is a two-dimensional carbon atom with a hexagonal honeycomb-like structure in which the sp2 hybridization occurs. GO sheets are highly oxidized and have oxygen-containing groups. Properties of electronics, mechanicals, magnetics, and optics, Oxidized Methods for Brodies, Staudenmaier, Hofmann, Hummers, Improved Hummers, and Tour's Methods Reduction of Graphene oxide methods Chemical Reduction using sodium borohydride, 2,4-dinitrophenylhydrazine, Hydrazine hydrate, Thermal Reduction, Hydrothermal Reduction, Exfoliation Reduction, Catalytic Reduction, and the green synthesis route for reduction, The reduction of graphene oxide has a wide range of applications, including its use in energy storage devices for Solar cells, Supercapacitors, LIG-based sensors, River Water sensors, Battery, hydrovoltaic generators, OLED Screen, and Graphene Shielding. This review will determine the future of a few applications.

A full potential all-electron density functional method within generalized gradient approximation is used to investigate the electronic, elastic and transport properties of cubic copper sulphide and copper selenide. The electronic structure suggests metallic behavior with a zero energy band gap for both materials. Elastic property calculations suggest a stiff material with the bulk to shear modulus ratio of 0.35 and 0.44 for Cu2S and Cu2Se respectively. The transport properties were estimated using the Boltzmann transport approach. Seebeck coefficient, electrical conductivity, thermal conductivity, and power factor all suggest a potential p-type conductivity for Cu2S and n-type conductivity for Cu2Se.

SiOx films, frequently derived from amino silane precursors, have found several applications with high added value. Although frequently used, the deposition of coatings from Tris(dimethyl amino)silane (TDMAS) has been reported to demand considerable amounts of energy, mainly due to the difficulty of oxidizing such compound. As it is well known, Plasma-enhanced atomic layer deposition (PEALD) is able to improve the oxidation efficiency even under low process temperatures. Owing to that, PEALD can be considered as a very promising technique for the deposition of SiOx coatings. In this work, it has been investigated the deposition of silicon oxide films using TDMAS at 150°C. It has been evaluated the effect of the plasma oxidation time (6 to 18 s) and of the atmosphere composition (pure O2 or O2+Ar) on the chemical structure, elemental composition and chemical bonding state of the films. Increasing the plasma oxidation time in pure O2 resulted in larger proportion of retained C (Si-CH3) whereas N was preserved in the structure (Si-N). on the other hand, the formation of SiOx films from TDMAS is favored in shorter oxidation times in O2 + Ar plasmas.

This research delves into the impact of complex low-speed wake flow structures on the aerodynamic characteristics of objects downstream. It employs the proper orthogonal decomposition (POD) method and the domain precursor simulation method to compare traditional methods and validate this approach. The study generates several flow structures of parallel dual-cylinder wakes with different scales and spacing. The variations in the aerodynamic coefficient of three downstream objects at various times passing through wakes of varying scales are appropriately compared and analyzed. The study establishes that the wake with a cylinder spacing of G=1.5 has a more compact and concentrated modal structure than that with a cylinder spacing of G=0.35. Smaller objects are more responsive to the wake flow structure with a spacing of G=1.5, whereas larger objects respond more to the flow structure with a spacing of G=0.35. The achieved results also reveal that the aerodynamic force coefficients of objects passing through the wakefield at different times are closely related to the temporal characteristics of the wake flow structure with different scales.

A new Pd(II) complex of the previously reported ligand N,N′-bis[(2,2′-dihydroxybiphen-3-yl)methyl]-N,N′-dimethylethylenediamine (L) was obtained from a DMF/H2O mixture. It differs from a Pd(II) complex of L previously obtained by sole DMF. The roles in the solid state assembly of solvent molecules and molecular conformation (driven by specific transition metal ions) were studied by comparing six complexes of L containing different metal centers (Ni(II), Cd(II), Cu(II), Pd(II)). Hirshfeld surface analysis, 2D fingerprint plots and energy frameworks calculations were used to investigate the intermolecular interactions within the crystal packing of the six complexes. As suggested by interaction energies, Pd(II) and Ni(II) complexes arrange to form ribbons, while Cd(II) and Cu(II) complexes form 3D networks. Interactions between complexes and solvent molecules in the previous Pd(II) complex are replaced by complex-complex interactions in the new Pd(II) complex, while BuOH and MeOH are interchangeable in the interactions within the crystal packing of the two Ni(II) complexes. Finally, solvent molecules are not involved in the crystal packing of the Cu(II) complex. The present study suggested that the solid state assembly of these systems is mainly driven by the molecular conformation, that depends in turn by the metal ion involved, while the solvent only plays a minor role.

Using the World Bank Global Findex Database for 91 countries in 2014, 2017, and 2021, we examine whether fintech levels influence bank performance and whether fintech’s interaction with GDP per capita causes differential effects on bank performance globally. Since fintech levels were already very high for rich countries when the World Bank started providing fintech development statistics in 2014, we estimate AbFintech by regressing fintech levels on GDP per capita by year. AbFintech is the difference between the fintech level and its fitted values. Then, using multiple regression analyses, we investigate the impact of AbFintech on bank performance worldwide, focusing on the differential effects of AbFintech and GDP levels on bank performance. We find AbFintech significantly increases bank performance, primarily in less developed countries. Specifically, AbFintech increases banks’ ROA in the least developed countries and net interest margin in the 75th percentile countries. Also, AbFintech decreases the cost-to-income ratio in the 75th percentile countries, while it increases the ratio in the most developed countries. AbFintech does not affect the ratio of noninterest income to total income, regardless of the level of economic development.

Species diversity has been shown to be influenced by environmental factors, but the mechanism underlying their relationship remains unclear across spatial scales. Based on field investigation data collected from 3,077 sample plots in temperate forest ecosystems, we compared tree species richness, evenness and dominance at 10 km × 10 km, 30 km × 30 km and 90 km × 90 km spatial scales. Then, we detected the scale dependence of changes in tree species composition on climate, topography and forest structure using variation partitioning and quantified their contribution to tree diversity with gradient boosted models (GBMs) and fitted their relationships. The magnitude of tree richness, evenness and dominance significantly increased with spatial scale. Ecological factors jointly accounted for 24.3%, 26.5% and 38.5% of the variation in tree species composition at the three spatial scales, respectively. Annual mean temperature had a strong impact on tree richness, evenness and dominance and peaked at an intermediate scale. Tree evenness and dominance increased with the variation of temperature but had upper and lower limits. Tree richness obviously increased with annual precipitation on multiple scales and decreased with annual sunshine duration at large spatial scale. Tree richness, evenness and dominance obviously increased with the variation elevation and diameter at breast height at large scales and small scales, respectively. Tree dominance decreased with tree height in a hump at small scale. The dependence of tree diversity on ecological factors increased with spatial scales. Furthermore, different factors exert various controls on tree diversity at different spatial scales, representing a comprehensive mechanism regulating tree diversity.

The crystal structure of quintinite, Mg4Al2(OH)12(CO3)·3H2O, from Jacupiranga alkaline complex (Cajati, São Paulo, Brazil) has been refined for two samples (91002 and C7029) using single-crystal X-ray diffraction data. The mineral crystallizes in the P-3c1 space group, a = 5.246/5.298, c = 15.110/15.199 Å for the samples 91002/C7029. The crystal structure consists of octahedral sheets with Mg and Al ordering according to the 3 × 3 superstructure. The Mg and Al atoms are coordinated by six hydroxylated oxygen atoms each with the average <Mg–O> and <Al–O> bond distances being in the ranges 2.022–2.053 Å and 1.974–1.978 Å, respectively. The interlayer structures are identical (in contradiction to the previous assumptions) and compose from disordered (CO3)2- groups and (H2O)0 molecules. The samples from Jacupiranga can be identified as quintinite-2T that is the second find of the polytype after the Kovdor alkaline complex (Kola peninsula, Russia). The powder X-ray diffraction pattern of quintinite-2T contains weak superstructure reflection at 4.57 Å (010) indicative of Mg and Al ordering. An important crystal-chemical criterion of quintinite is the interlayer distance (d00n-value) of ~ 7.56 Å, which is steady for natural specimens from various findings worldwide.

Abstract: Arranged patterns obtained by ultrafast laser processing on the surface of Ti/Cu/Ti/Si and Ti/Zr/Ti/Si thin film systems are reported. Two differently designed multilayer thin films, Ti/Cu/Ti/Si and Ti/Zr/Ti/Si, were deposited on silicon by the ion sputtering method. The bioactive surfaces on these systems involve the formation of laser-induced periodic surface structures (LIPSS) in each of the laser-written lines of mesh patterns on 5x5 mm areas. The formation of nano- and micro-patterns with an ultra-thin oxide film on the surfaces was used to observe the effects of morphology and proliferation of the MRC-5 cell culture line. To determine whether Ti-based thin films have a toxic effect on living cells, an MTT assay was performed. The relative cytotoxic effect as a percentage of surviving cells showed that there was no difference in cell number between the Ti-based thin films and the control cells. There was also no difference in the viability of the MRC-5 cells, except for the Ti/Cu/Ti/Si system, where there was a slight 10% decrease in cell viability.

Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

Most developing countries with petroleum resources are constrained in the ability to refine their oil and gas resources. This virtually results in the involvement of the International Oil Company (IOC) by the National Oil Company (NOC) of a particular nation to enter into an agreement to achieve the production of oil based on an agreed framework. However, in cur-rent development, there is little focus on the contractual agreement, particularly on the pro-duction sharing agreement by the IOC in the exploration of petroleum resources of developing countries. The primary objective of this paper is to critically explore the contract structure of production sharing agreement by the IOC in the exploration and development of petroleum resources in developing countries. Content analysis was used as the methodology of the study after examining several literatures. The findings indicate that the contract structure of the production sharing agreement (PSA) between NOC and IOC plays a significant role in the cost and risk of exploration and development of oil. In addition, it is noted that the joint committee of the NOC and IOC plays a paramount role in monitoring the operations of PSA between the NOC and IOC. Hence, from the gross oil production, the NOC gets its share as profit while IOC gets its share income tax. As an instrument of contract structure in the oil and gas sector, PSA needs further entrenchment between IOC and NOC to avoid likely issues that can emanate between the two parties in the face of current developments.

Apis cerana and Apis mellifera, are very important honey species for agriculture in Asian countries. In recent decades, A. cerana populations have sharply declined in all Asian countries as a result of Sacbrood Virus infection and have now recovered to their original size. It can change the genetic structure of local populations of A. cerana. We used the nuclear gene Vitellogenin VG to assess the genetic structure of local populations of A. cerana and the signature of adaptive selection. We performed a population genetic analysis of the honey bees A. cerana from South Korea in comparison with A. cerana samples from Russia, Japan, Nepal, and China. The sequences of the gene VG of a closely related honey bee species, A. mellifera, from India and Poland were used as outgroup samples. A comparative analysis of northern and southern A. cerana populations was performed. The signatures of positive adaptive selection were found in the local population of A. cerana. We performed the Tajima's neutrality D test for A. cerana populations from different local populations based on the gene VG exon sequences. All A. cerana populations showed signs of population size expansion following the possible recent decline in population sizes. The local populations of A. c. koreana were subdivided according to their geographical distribution into southern, northern, and central Korean clusters. The gene VG exon sequences can be used as informative markers for monitoring the changes in genetic structure and adaptation to the environment processes in A. cerana populations.

The bimodal grain-size distribution 0.9KNbO₃-0.1BaTiO₃ ceramics, with a typical perovskite structure in tetragonal phase at room temperature, were successfully prepared by an induced abnormal grain growth (IAGG) method at a relatively low sintering temperature. In this bimodal grain-sized distribution structure, the extra-large grains (about 10‒50 μm) were evolved from the micron-sized filler powders and the fine grains (about 0.05‒0.35 μm) were derived from the sol precursor matrix. The 0.9KNbO₃-0.1BaTiO₃ ceramics exhibit relaxor-like behavior with the diffused phase transition near room temperature, and confirmed by the existence of the polar nanodomain regions (PNRs) using the HRTEM images. The large room-temperature electrocaloric (EC) effect was found, characterized by an adiabatic temperature drop of 1.5 K, an isothermal entropy change of 2.48 J kg^-1 K^-1, and high EC strengths of ïDT/DEï = 1.50×10^-6 KmV^-1 and DS/DE = 2.48×10^-6 Jmkg^-1K^-1V^-1directly measured under E = 1.0 MV/m. These excellent ECEs demonstrate that this simple IAGG method is highly appreciated for synthesizing high-performance EC materials for efficient cooling devices.

In this paper a new monolithic Eulerian formulation in the framework of non-classical continuum is presented for the analysis of fluid-strucutre interaction problems. In this respect, Cosserat continuum theory taking into account the micro-rotational degrees of freedom of the particles is considered. Continuum description of the model and variational formulation of the governing flow dynamics for non-classical -fluid-structure interaction nCFSI is presented. The model is analyzed by computing a well known benchmark problem by Hecht and Pironneau [16]. The algorithmic description is presented and implemented using FreeFEM++. Code is validated with the benchmark solution of Turek and Hron [38] in case of flow around a flag attached with cylinder. New microstructral behavior of the solution is studied and numerical simulations and results are shown in the form of figures. Some interesting feature of the flow is observed and microstructural characteristics are discussed.

This study aims to evaluate the land surface temperature (LST) and the thermal characteristics of the Urban Canopy Layer (UCL) of the urban canyon in Avenida Rio Branco in the Central Business District (CBD) of Rio de Janeiro during summer. In order to conduct this evaluation, two methods were employed: 1) TIRS Landsat-8 sensor for data selection and processing (latest generation, 2011-2020); ; 2) field survey using nine sampling points — seven along two mobile transects, one fixed point, and one vertical measurement point, which required the use of a RPA (Remotely Piloted Aircraft). Three categories of analysis were established for the field survey based on the prevailing synoptic situations: stability, instability, and post-instability. The CBD is characterized by extensive areas with surface heat islands, in which temperatures were higher than 38.9°C; the areas with milder LSTs were Campo do Santana, Avenida Rio Branco, and one of the Mixed-Use Zones (Praça Mauá). With respect to Rio Branco Avenue, the LST niches of lowest elevation were derived through building shadowing; however, the orbital data diverged from the observation data of the ten field-study days. In situ data revealed that the characteristics urban morphology of Avenida Rio Branco is susceptible to the formation of heat islands, presenting heat islands of very strong magnitude (over 6.1°C) in atmospheric stability, strong magnitude (4.1-6.0°C) in atmospheric instability, and moderate magnitude (2.1°C-4.0°C) in post-atmospheric instability. Despite the synoptic situation, thermal cores were concentrated at 1 pm. The intersection between Avenida Rio Branco, Rua do Ouvidor, and Praça Mauá stored most of the solar energy received during the day due to the greater sky obstruction caused by the verticalization. Finally, vertical analysis demonstrated the formation of a thermal inversion on the night of the highest mean air temperature (29.5°C), probably, due to the roughness and number of buildings in the urban canyon.

A new method is proposed to increase rejection in microfiltration by applying membrane oscillation using a new type of microfiltration membranes with slotted pores. The oscillations applied to the membrane surface result in reducing membrane fouling and increasing separation efficiency. An exact mathematical solution of the flow in the surrounding solution outside the oscillating membrane is developed. The oscillation results in appearance of the lift velocity, which moves oil particles away from the membrane. The latter results in both reducing membrane fouling and increasing oil droplets rejection. This developed model was supported by the experimental results for oil water separation in produced water treatment. It was proven that oil droplet concentration reduced notably in the permeate due to the membrane oscillation and that applied shear rate caused by the membrane oscillation is also reduce pore blockage. New generation of microfiltration membranes with slotted pores was used in the experiments.