The steady-state, coupled heat and mass transfer from a fluid flow to a sphere accompanied by an exothermal catalytic chemical reaction on the surface of the sphere is analysed taking into consideration the effect of thermal radiation. The flow past the sphere is considered steady, laminar and incompressible. The radiative transfer is modeled by P₀ and P₁ approximations. The mathematical model equations were discretized by the finite difference method. The discrete equations were solved by the defect correction – multigrid method. The influence of thermal radiation on the sphere surface temperature, concentration and reaction rate was analysed for three parameter sets of the dimensionless reaction parameters. The numerical results show that only for very small values of the Prater number the effect of thermal radiation on the surface reaction is not significant.

The sand-dust horizontal flux is an important parameter for the study on aeolian sand transport, as well as an important foundation. In this study, a field experiment was developed to measure the data of aeolian transport and microclimate during different dust events with an auto sand sampler, a piezoelectric saltation sensor (H11-Sensit) and a 10 m high meteorological tower in Ta Zhong, the hinterland of the Taklimakan Desert from July to August in 2010. Then, the sampling efficiency of auto sand sampler and horizontal dust flux of near surface were analyzed based on observed data. The results were as follows: sand collector skip turnover increased with the increase of the intensity of dust weather frequency increases, the power function relationship y=2.115 x0.9841, R2 = 0.9206, flip frequency per minute increased from 0.2794 times to 1.3041 times, change is obvious; With the strength of the weather, time to flip the average sediment is shrinking. Sandstorm weather, skip to flip a volume of 3.7160 g, grade I flying sand weather flip a volume of 4.0275 g, the amount of class II flying sand weather turns over a 5. 0035g.The horizontal dust flux of different dust events that calculated with the equation Q=256M; the maximum of one dust event was about 190.335 kg, and the minimum was 1.2 kg. Overall, the sand transportation rate increased with wind speed. However, the changes of sand transportation rate did not quite fit in with wind speed during some dust events, and in this case the corresponding surface temperature was significantly higher. The experimental data obtained can provide theoretical basis for regional sand control and enacting effective engineering measures.

Ocean temperatures are increasing. Little work has been done to examine the effects that these changes will have on fishery production. The study at hand seeks to incorporate the influence of climate change into established bioeconomic fishery models. Stock biomass is approximated to be a function of sea surface temperature. Following a feasible generalized least squares regression using data from the Western and Central Pacific, the interaction between fishery effort and temperature is found to be statistically significant. From this model, various functional forms relating effort, catch, and temperature are specified. In particular, a function that returns an effort requirement given a target catch level and temperature forecast is generated.The importance of these tools for fishery management is explored through application to Western and Central Pacific tuna fisheries. Recommendations for extensions into future research are made and the foundation for a model of efficient effort allocation across time and the entirety of a management area, given changing temperatures, is specified.

Taking a typical forest underlying surface as the research area, this study employed the unmanned aerial vehicle (UAV) photogrammetry to explore more accurate canopy parameters including tree height and canopy radius, which were used to improve the Noah-MP land surface model conducted in Dinghushan Forest Ecosystem Research Station (CN-Din). While the canopy radius was fitted as a Burr distribution, the canopy height of CN-Din forest followed a Weibull distribution. The replacement of the parameters by these observed UAV would result in the Noah-MP model. It was found that the influence on the simulation of the energy fluxes could not be negligible, and the main influence of these canopy parameters was on the latent heat flux which could decrease up to -11% in the midday while increase up to 15% in the nighttime. Additionally, this work indicated that the description of the canopy characteristics for the land surface model should be improved to accurately deliver the heterogeneity for the underlying surface.

In this study, the optimal condition for the extraction of antioxidants from the fruit Buah Mahkota Dewa (Phaleria macrocarpa) was determined by using Response Surface Methodology (RSM). The optimization was applied using central composite design (CCD) to investigate the three independent variables, namely extraction temperature (^oC), extraction time (minutes) and extraction solvent to-feed ratio (%v/v) on the responses of free radical scavenging activity (DPPH), ferric ion reducing power assay (FRAP), total phenolic content (TPC) and total flavonoid content (TFC).The optimal conditions for the antioxidants extraction were found to be extraction temperature (64^oC), extraction time (66 minutes) and solvent to-feed ratio (75 %v/v) with the highest percentage yield of DPPH, FRAP, TPC and TFC were 86.85%, 7.47%, 292.86 mg/g and 3.22 mg/g respectively. Moreover, the data were subjected to response surface methodology (RSM) and the results showed that the polynomial equations for all models were significant, did not show lack of fit, and presented adjusted determination coefficients (R²) above 99%, proving the yield of phenolic, flavonoid and antioxidants activities obtained experimentally were close to the predicted values and the suitability of the model employed in RSM to optimize the extraction conditions. Hence, in this study, the fruit from P.macrocarpa could be considered to have the strong antioxidant ability and can be used in various cosmeceutical or medicinal applications.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

In this paper, a swarm trajectory planning method is proposed for multiple autonomous surface vehicles (ASVs) in an unknown and obstacle-rich environment. Specifically, based on the point cloud information of the surrounding environment obtained from local sensors, a kinodynamic path searching method is used to generate a series of waypoints in the discretized control space at first. Next, after fitting B-spline curves to the obtained waypoints, a nonlinear optimization problem is formulated to optimize the B-spline curves based on gradient-based local planning. Finally, a numerical optimization method is used to solve the optimization problems in real-time to obtain collision-free, smooth and dynamically feasible trajectories relying on a shared network. Simulation results demonstrate the effectiveness and efficiency of the proposed swarm trajectory planning method for a network of ASVs.

Cardiovascular diseases continuing to be a major contributor to illness and death on a global scale and the implementation of stents has given rise to a revolutionary transformation in the field of interventional cardiology. The thrombotic and restenosis complications associated with stent implantation pose ongoing challenges. In recent years, bioactive coatings have emerged as a promising strategy to enhance stent hemocompatibility and reduce thrombogenicity. This review article provides an overview of the surface engineering techniques employed to improve the hemocompatibility of stents and reduce thrombus formation. It explores the mechanisms underlying thrombosis and discusses the factors influencing platelet activation and fibrin formation on stent surfaces. Various bioactive coatings, including anticoagulant agents, antiplatelet agents, and surface modifications, are discussed in detail, highlighting their potential in reducing thrombogenicity. Evaluation methods for assessing hemocompatibility and thrombogenicity are also reviewed, ranging from in vitro assays to animal models. Recent advances in the field, such as nanotechnology-based coatings and bioactive coatings with controlled drug release systems, are highlighted. Surface engineering of bioactive coatings holds great promise for enhancing the long-term outcomes of stent implantation by enhancing hemocompatibility and reducing thrombogenicity. Future research directions and potential clinical applications are discussed, underscoring the need for continued advancements in this field.

Recently, polyetheretherketone (PEEK) has shown promising dental applications; although surface treatment is essential for dental applications owing to its poor surface energy and wettability, no consensus on an effective treatment method has been achieved. In this study, we attempt to carboxylate PEEK sample surfaces via Friedel–Crafts acylation using succinic anhydride and AlBr3. The possibility of further chemical modifications using carboxyl groups is examined. The samples are subjected to dehydration–condensation reactions with 1H,1H-pentadecafluorooctylamine and N,N'-dicyclohexylcarbodiimide. The sample surface properties at each reaction stage are evaluated. An absorption band in the 3300–3500 cm-1 wavenumber region is observed. Additionally, peak suggestive of COOH is observed in the sample spectra. Secondary modification diminished the absorption band in 3300–3500 cm-1 and a clear F1s signal is observed. Thus, Friedel–Crafts acylation with succinic anhydride produces carboxyl groups on the PEEK sample surfaces. Further chemical modification of the carboxyl groups by dehydration-condensation reactions is also possible. Thus, a series of reactions can be employed to impart desired chemical structures to PEEK surfaces.

The performance and lifespan of cutting tools are significantly influenced by their surface quality. The present report highlights recent advances in enhancing the surface characteristics of tungsten carbide and high-speed steel cutting tools using a novel micro-machining technique for polishing and edge-honing. Notably, the main aim is to reduce the surface roughness while maintaining the hardness of the materials at an optimal level. By conducting a thorough analysis, of surfaces obtained with different techniques. It was that micro-machining method effectively decreased the surface roughness of the cutting tools, most effectively of the techniques investigated. Significantly, the surface roughness is reduced from an initial measurement of 400 nm to an impressive value of 60 nm. No significant change in hardness was observed, which guarantees the maintenance of the mechanical properties of the cutting tools. This analysis enhances the comprehension of surface enhancement methodologies for cutting tools through the presentation of these findings. The observed decrease in surface roughness, along with the consistent hardness, exhibits potential for improving tool performance. These enhancements possess the capacity to optimise manufacturing processes, increase tool reliability, and minimise waste generation.

In order to solve the problem of many constraints and complex navigation environment in the path planning of unmanned surface vehicle(USV), an improved Sparrow search algorithm com-bining Cubic chaotic map and Gaussian random walk strategy was proposed to plan it. Firstly, in the population initialization stage, Cubic chaotic map was used to replace the random generation method of the traditional sparrow search algorithm to optimize the uneven initial distribution of the population and improve the global search ability of the population. Secondly, in the late it-eration of the algorithm, the standard deviation of fitness is introduced to determine whether the population is trapped in the local optimum. If true, the Gaussian random walk strategy is used to perturb the optimal individual and assist the algorithm to escape the local optimum. Thirdly, the chosen water environment is modeled, and the navigation information of the original inland electronic navigation chart(ENC) is preprocessed, gridized, and the obstacle swelling is processed. Finally, the path planning experiments of USV are carried out in inland ENC grid environment. The experimental results show that, compared with the traditional sparrow search algorithm, the average fitness value of the path planned by improved sparrow search algorithm is reduced by 14.8%, and the variance is reduced by 49.9%. The path planned by the algorithm is of good quality and high stability, and combined with ENC, it can provide a reliable path for USV.

Abstract: For the problem of small target of printed circuit board surface defects and low detection accuracy, the printed circuit board surface defect detection network DCR-YOLO is designed to meet the premise of real-time detection speed and effectively improve the detection accuracy. Firstly, the backbone feature extraction network DCR-backbone, consisting of two CR residual blocks and one common residual block, is used for small target defect extraction on printed circuit boards. Secondly, the SDDT-FPN feature fusion module is responsible for the fusion of high level features to low level features, while enhancing feature fusion for the feature fusion layer where the small target prediction head YOLO Head-P3 is located to further enhance the low level feature representation. the PCR module enhances the feature fusion mechanism between the backbone feature extraction network and the SDDT-FPN feature fusion module at different scales of feature layers. the C5ECA module is responsible for adaptive adjustment of feature weights and adaptive attention to the requirements of small target defect information, further enhancing the adaptive feature extraction capability of the feature fusion module. Finally, three YOLO-Heads are responsible for predicting small target defects for different scales. Experiments show that the DCR-YOLO network model detection Map reaches 98.58%, the model size is 7.73MB, which meets the lightweight requirement, and the detection speed reaches 103.15fps, which meets the application requirements for real-time detection of small target defects.

With the dramatic increase in the number of mobile users and wireless devices accessing the network, the performance of the fifth generation (5G) wireless communication systems has been severely challenged. Reconfigurable intelligent surfaces (RIS), one of the potential technologies for the sixth generation (6G), has received a lot of attention. Since it is easier to deploy, consumes less power, and is inexpensive. RIS is an electromagnetic metamaterial that serves to reconfigure the wireless environment by adjusting the phase, amplitude and frequency of the wireless signal. To maximize channel transmission efficiency and improve the reliability of communication systems, the acquisition of channel state information (CSI) is essential. Therefore, an effective channel estimation method guarantees the achievement of excellent RIS performance. This paper conducts a comprehensive investigation of the existing channel estimation methods of RIS, analysis and comparison of channel model building and CSI acquisition schemes in different frequency bands, in addition to a comprehensive description of generic channel estimation methods, with a focus on the application of deep learning. Finally, we conclude the paper and provide an outlook in the future development of RIS channel estimation.

The Land Surface Temperature (LST) is an essential indicator for analyzing the Surface Urban Heat Island (SUHI). A factor contributing to its occurrence is the reflections of the different materials in urban and rural areas, which significantly affect the energy balance near the surface. Therefore, recent studies have increasingly used the Local Climate Zones (LCZ) classification system to discriminate those urban areas. Therefore, our study aims to do a systematic review using the PRISMA method of LCZ classification applied to understand the LST and the SUHI phenomenon. At first, it was found in the scientific literature 10,403 articles which, after passing through filtering stages, resulted in 51 that were further analyzed. Our results showed that these articles were very recent, beginning in 2016. However, presenting an increasing trend. China was the country with more studies. Landsat and TERRA/AQUA sensors appeared in 82% of the studies. The method that appears the most to LCZ definitions is from the World Urban Database. Finally, considering the current climatic changes, this systematic review can help new studies on SUHI identification through LCZ in different world areas using remote sensing data to estimate the LST.

Impervious surface area (ISA) is a crucial indicator for quantitative urban studies. It is also important for land use land cover classification, groundwater recharge, sustainable development, urban heat island effects, and more. Spectral ISA mapping suffers from mixed pixel problems, especially with bare soil. This study aims to develop an ISA index for spatiotemporal urban mapping from common multispectral bands by reducing soil signature better than in previous studies. This study proposed a global impervious surface area index (GISAI) enhancing ISA mapping accuracy using a temporal parameter of the remote sensing (RS) dataset. Bare soil spectral reflectance shows more fluctuation than urban ISA. Therefore, the study uses minimum composites of earlier urban indices to compile minimum soil signature. It is later improved by removing water, increasing the contrast between bare soil and urban ISA and reducing bright bare soil area. This study maps the ISA of all 12 megacities using the annual RS image collection from 2021. GISAI reduced the bare soil signature and achieved an overall accuracy of 87.29%, F1-score of 0.84, and Kappa coefficient of 0.75. However, it has some limitations with grey bare soil and barren hilly areas. By limiting bare soil signature, GISAI broadens the scope of inter-urban studies globally and lengthens potential urban time-series analysis using common multispectral bands.

The extremely controversial conclusions about the function of human interferon-gamma (hIFNγ) C-terminus as well as the lack of a consistent model explaining its role in the receptor binding prompted us to scrutinize the interaction of hIFNγ with its extracellular receptor hIFNGR1 in different scenarios by means of molecular dynamics simulations. We find that the two molecules alone fail to form a stable complex but the presence of heparan-sulfate-like oligosaccharides largely facilitates the process by both demobilizing the highly flexible C-termini of the cytokine and assisting in the proper positioning of its globule between the receptor subunits. An antiproliferative-activity essay on cells depleted from surface sulfation confirms qualitatively the simulation-based multistage complex-formation model. Our results reveal the key role of HS and its proteoglycans in all processes involving hIFNγ signalling.

The video images captured at long range usually have low contrast floating objects of interest on a sea surface. A comparative experimental study of the statistical characteristics of reflections from floating objects and from the agitated sea surface showed the difference in the correlation and spectral characteristics of these reflections. The functioning of the recently proposed modified matched subspace detector (MMSD) is based on the separation of the observed data spectrum on two subspaces: relatively low and relatively high frequencies. In the literature the MMSD performance has been evaluated in generally and moreover using only a sea model (additive Gaussian background clutter). This paper extends the performance evaluating methodology for low contrast object detection and moreover using only the real sea dataset. This methodology assumes an object of low contrast if the mean and variance of the object and the surrounding background are the same. The paper assumes that the energy spectrum of the object and the sea are different. The paper investigates a scenario in which an artificially created model of a floating object with specified statistical parameters is placed on the surface of a real sea image. The paper compares the efficiency of the classical Matched Subspace Detector (MSD) and MMSD for detecting low-contrast objects on the sea surface. The article analyzes the dependence of the detection probability at a fixed false alarm probability on the difference between the statistical means and variances of a floating object and the surrounding sea.

This paper investigates the path following control problem for a unmanned surface vehicle (USV) in the presence of unknown disturbances and system uncertainties. The simulation study combines two different types of sliding mode surface based control approaches due to its precise tracking and robustness against disturbances and uncertainty. Firstly, an adaptive linear sliding mode surface algorithm is applied, to keep the yaw error within the desired boundaries and then an adaptive integral non-linear sliding mode surface is explored to keep an account of the sliding mode condition. Additionally, a method to reconfigure the input parameters in order to keep settling time, yaw rate restriction and desired precision within boundary conditions is presented. The main strengths of proposed approach is simplicity, robustness with respect to external disturbances and high adaptability to static and dynamics reference courses without the need of parameter reconfiguration.

Water-soluble nonionic surfactant, pentaethylene glycol monododecyl ether, C12E5, spontaneously blooms to the surface of spin-cast hydrophobic polyiso-prenes, generating hydrophilic surfaces. This system represents a simple model for hydrophilic chemical modification of rubbery polymers yet demonstrates surprisingly rich, complex and unexpected behaviour. The ver-tical depth profiles were quantified using neutron reflectometry (NR) and deuterated surfactant, and the surface properties were characterized using con-tact angle analysis and atomic force microscopy (AFM). Despite the low surface tension of the toluene solvent used in film preparation and the low surface en-ergy of the PI matrix, NR depth profiles revealed clear evidence of surfactant segregation. This surface layer was typically thicker than a monolayer, but incomplete, yet was remarkably stable with respect to dissolution, even when exposed to hundreds of thousands of times the volume of water required to dissolve all the surfactant on the surface. Despite the apparent resistance to removal from the surface, water exposure does alter the subsequent wettabil-ity of the surface, with a hydrophilic-to-hydrophobic transition occurring after rinsing. Complementary AFM images of these C12E5 / cis-PI films showed unexpected strand-like features on the surface of the film, which we attribute to a non-uniform lateral distribution of some of the surfactant. This surface structure becomes more evident after rinsing, and it appears that there are two distinct populations of surfactant on the PI film surface. We conclude that some of the bloomed surfactant exists as layers, which are relatively inert with respect to rinsing or surface modification, and some is laterally inhomogene-ous. This latter population is primarily responsible for surface wetting be-havior, but is not detected by specular NR.

Irrigation is a useful crop enhancement procedure up to the point where free surface water appears. Thereafter, water can begin to flow into waterways, leaching nutrients and giving rise to environmental damage, as well as being a waste of a precious resource. The current work addresses the problem of measuring free water on the surface of agricultural soils by a real-time acoustic remote sensing method. Directional acoustic transmitter and receiver arrays are used to define a ‘footprint’ on the ground from which changes in reflectance are sensed. These arrays are mounted on a moving irrigator. Chirp signals are used to provide along-path resolution and to ensure robustness against unwanted acoustic background noise from farm machinery and the irrigator. Field measurements have been conducted above a well-defined ‘quadrat’ with controlled and measured water content, and also with the instrument mounted on an operational irrigator. A structured light camera mounted above the footprint is used to validate surface water fraction. It is found that the areal fraction of free water on the soil surface can be reliably estimated from changes in the amplitude of the reflected sound waves. The mechanism giving rise to the observed acoustic reflectivity changes is discussed and a model is developed which agrees with normalized intensity observations with a coefficient of determination R2 between 0.65 and 0.83. The rms error between model predictions and observations is comparable to the rms variation of the measurements, indicating that there is insignificant error due to the choice of model.

Solar Insolation is the major contributor of earth’s radiation and energy budget. The insolation reaching the surface is a prime input for eco-physiological processes such as evapotranspiration and photosynthesis. Therefore, it is as critical component to assess bio-energy and bio-fuel resources. It is also a crucial input to crop simulation model for yield forecasting and its further applications in solar energy solutions. Although ground observations are better for accuracy purpose, they have challenges of maintenance, regular calibration and upkeeping etc. This call for the continuous spatio-temporal satellite based observations barring the acceptable accuracy. In case of INSAT3D/3DR, Bhattacharya et al. (2015) have derived the surface insolation product which is being used widely. We propose a method of improvement in this product. It is envisaged that a correction applied with the help of ground truth estimates may enhance the utilization of insolation products derived from INSAT3D/3DR datasets. In the present study, surface insolation product derived from INSAT 3D/3DR data at an interval of 30 minutes each (collectively 15 minutes interval) with 4 km spatial resolution was used for duration from May-2017 to Apr-2019 over Nagpur. Ground truth observations for same duration were carried out with CNR4, which were used to correct the INSAT 3D/3DR surface insolation product using the statistical best-fit method. Corrected INSAT 3D/3DR products are found correlating with the ground values well with differences of approximately < 1 W/m2. Best-fit parameters evolved in the present study uses only 2 years of simultaneous ground and satellite data which can be further improved by multi-year data base. We propose better utilization of INSAT 3D/3DR based surface insolation products in the assessment of solar resource mapping over Nagpur (and possibly other regions, such as Bhandara) with the help of best-fit parameters as assessed in the present study.

Unmanned surface vehicles have the advantages of maneuverability, concealment, wide activity area and low cost of use. Therefore, they have broad application prospects. This makes unmanned surface vehicles a research hotspot at home and abroad, and the sensing technology is the basis for the unmanned surface vehicles to perform tasks. The perception technology based on optical vision has the advantages of convenient application, relatively low cost, easy data acquisition and large amount of information, and has been widely studied by scholars at home and abroad. This paper mainly discusses the research of optical vision in unmanned surface vehicles from five aspects: Firstly, the water surface image preprocessing based on unmanned surface vehicles, mainly including water surface image stabilization research and defogging enhancement research; two water boundary detection; It is the use of light vision target detection; the fourth is the surface target tracking method. Finally, the light vision research of unmanned surface vehicles is summarized and forecasted.

An all-weather land surface temperature (LST) product derived at the Satellite Application Facility on Land Surface Analysis (LSA-SAF) is presented. The product is based on clear-sky LST retrieved from MSG/SEVIRI infrared (IR) measurements, complemented by LST estimated with a land surface energy balance (EB) model to fill gaps caused by clouds. The EB model solves the surface energy balance mostly using products derived at LSA-SAF. The new product is compared with in situ observations made at 3 dedicated validation stations, and with a Microwave (MW) based LST product derived from AMSR-E measurements. The validation against in-situ LST indicates an accuracy of the new product between -0.8 K and 1.1 K and a precision between 1.0 K and 1.4 K, generally showing a better performance than the MW product. The EB model shows some limitations concerning the representation of the LST diurnal cycle. Comparisons with MW LST generally show higher LST of the new product over desert areas, and lower LST over tropical regions. Several other imagers provide suitable measurements for implementing the proposed methodology, which offers the potential to obtain a global, nearly gap-free LST product.

On January 8, 2005, a surface melt event began on the interior portion of Ross Ice Shelf. While many surface melt events on Ross Ice Shelf are caused by the advection of warm air onto the shelf from the Ross Sea, surface winds during this event were directed offshore and the spatial pattern of surface melt was inconsistent with the Southern Ocean serving as a heat source. Rather, due to the interior location of the surface melt coupled with prevailing wind direction and surface temperature data it is thought that adiabatic warming of Föhn winds is the driving cause of this melt event. Passive Microwave (SSM/I) imagery was used to determine surface melt occurrence and the event’s extent. Spatial patterns of surface melt were then compared to NCEP/NCAR reanalysis output for several synoptic weather variables including surface temperatures, sea level pressure and surface vector winds. Synoptic-scale weather conditions were consistent with those that would produce downsloping wind (föhn) conditions in the interior of the Ross Ice Shelf where the anomalous surface melt was located.

In this paper, sea surface wind speed (SSWS) retrieval from Gaofen-3 (GF-3) quad-polarization stripmap (QPS) data in vertical-vertical (VV), horizontal-horizontal (HH) and vertical-horizontal (VH) polarizations is investigated in detail based on 3,170 scenes acquired from October 2016 to May 2018. The radiometric calibration factor of the VV polarization data is examined first. This calibration factor generally meets the requirement of SSWS retrieval accuracy with an absolute bias of less than 0.5 m/s but shows highly dispersed characteristics. These results lead to SSWS retrievals with a small bias of 0.18 m/s but a rather high root mean square error (RMSE) of 2.36 m/s compared with the ERA-Interim reanalysis model data. Two refitted polarization ratio (PR) models for the QPS HH polarization data are presented. Based on a combination of the incidence angle- and azimuth angle-dependent PR model and CMOD5.N, the SSWS derived from the QPS HH data shows a bias of 0.07 m/s and an RMSE of 2.26 m/s relative to the ERA-Interim reanalysis model wind speed. A linear function relating SSWS and the normalized radar cross section (NRCS) of QPS VH data is derived. The SSWS data retrieved from the QPS VH data show good agreement with the WindSat SSWS data, with a bias of 0.1 m/s and an RMSE of 2.02 m/s. We also apply the linear function to the GF-3 Wide ScanSAR data acquired for the typhoon SOULIK, which surprisingly yields a very good agreement with the model results. A comparison of SSWS retrievals among three different polarization datasets is also presented. The current study and our previous work demonstrate that the general accuracy of the SSWS retrieval based on GF-3 QPS data has an absolute bias of less than 0.3 m/s and an RMSE of 2.0 ±0.2 m/s relative to various datasets. Further improvement will depend on dedicated radiometric calibration efforts.

As the energy efficiency demands for future buildings become increasingly stringent, preliminary assessments of energy consumption are mandatory. These are possible only through numerical simulations, whose reliability crucially depends on boundary conditions. We therefore investigate their role in numerical estimates for the usage of geothermal energy, performing annual simulations of transient heat transfer for a building employing a geothermal heat pump plant and energy piles. Starting from actual measurements, we solve the heat equations in 2D and 3D using COMSOL Multiphysics and IDA-ICE, and discover a negligible impact of the multiregional ground surface boundary conditions. Moreover, we verify that the thermal mass of the soil medium induces a small vertical temperature gradient on the piles surface. We also find a roughly constant temperature on each horizontal cross-section, with nearly identical values if the average temperature is integrated over the full plane or evaluated at one single point. Calculating the yearly heating need for an entire building we then show that the chosen upper boundary condition affects the energy balance dramatically. Using directly the pipes’ outlet temperature induces a 54% overestimation of the heat flux, while the exact ground surface temperature above the piles reduces the error to 0.03%.

Sea ice surface roughness affects ice-atmosphere interactions, serves as an indicator of ice age, shows patterns of ice convergence and divergence, affects the spatial extent of summer melt ponds, and ice albedo. We have developed a method for mapping sea ice surface roughness using angular reflectance data from the Multi-angle Imaging SpectroRadiometer (MISR) and lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). Using an empirical data modeling approach, we derived estimates of Arctic sea ice roughness ranging from centimeters to decimeters meters within the MISR 275-m pixel size. Using independent ATM data for validation, we find that histograms of lidar and multi-angular roughness values are nearly identical for areas with roughness <20 cm but that for rougher regions, the MISR-derived roughness has a narrower range of values than the ATM data. The algorithm is able to accurately identify areas that transition between smooth and rough ice. Because of its coarser spatial scale, MISR-derived roughness data have a variance of about half that ATM roughness data.

Regarding number of vehicles, forest roads are characterized by low traffic intensity, but on the other hand great values of ground pressure between wheels of timber truck units and forest road surface occur, often with pressures values above 80 kN which additionally causes damage of the upper and lower forest road layer. There are currently several methods for assessing condition of a forest road surface which are mainly used for assessing state of public roads, but can be used in forestry as well. Assessing condition of forest road surface was done by measuring vibrations with a specially developed software for Android OS installed on a Huawei MediaPad 7 Lite. Software measured vibrations in all three axes, coordinates of device, speed of the vehicle and time. Aim of this research was to determine accuracy of collected data so that this method can be used for scientific and practical purposes. Research was carried out on the segment of a forest road during driving a vehicle equipped with a measuring device. Tests were performed in both driving direction of the forest road segment with different measuring frequencies, tyre inflation pressures and driving speeds. Values of vibrations were classified and translated on a map of forest road together with devices’ measured coordinates. Vibration values were compared with places of recorded forest road surface damages. Research results show no significant difference in vibration values between 1 Hz and 10 Hz of measurement frequencies. Based on the analysis of collected data and obtained results, it is clear that it is possible to assess the condition of a forest road surface by measuring vibrations. The greatest values of vibrations were recorded on the most damaged parts of the forest road. Vibrations do not depend on tyre inflation pressure, but ranges of vibrations are decreasing with decreasing driving speed. Accuracy of collected data depends on GPS signal quality, so it is recommended that each segment of forest road is recorded twice so that location of damages on forest road can be confirmed with certainty.

In the field of nasal delivery, one of the most fascinating applications is the delivery of drugs directly to the central nervous system bypassing the blood brain barrier. This approach would provide a series of benefits, such as dose lowering and direct targeting of potent drugs, ultimately reducing their systemic side effects. Recently, clinical trials have explored the nasal administration of insulin for the treatment of Alzheimer’s disease, with promising results. The use of nanomedicines could provide further options for making nose-to-brain delivery reality. In particular, apart from the selection of devices able to deposit the formulation in the upper part of the nose, surface modification of these nanomedicines appears the key strategy to optimize the delivery of drugs from the nasal cavity to the brain. In this review, nanomedicines delivery approaches based on surface electrostatic charges, mucoadhesive polymers, as well as chemical moieties targeting nasal epithelium, will be discussed and critically evaluated for nose-to-brain delivery.

Sputtered reactive multilayers applied as a heat source in electronic joining processes are an emerging technology. Their use promises low-stress assembly of components while improving the thermal contact and reducing the thermal resistance. Nanostructured surface modifications can significantly enhance adhesion and reliability of joints between different materials. This work examines reactive multilayer of nickel and aluminum, directly sputtered on nanostructured black silicon surfaces and compares their phase transformation with reference samples deposited on pristine silicon surface. The investigation of the quenched self-propagating reaction reveals a clear influence of the nanostructured surface on the prolongation of the phase transition. Rapid thermal annealing tests result in the formation of Al_1.1Ni_0.9 phase. The nanostructured interface seems to hinder the full transformation of the parent material. The surface modification improves the adhesion of the formed alloy on silicon surfaces and can possibly increase the reliability of joints based on reactive aluminum/nickel multilayer. The use of black silicon, a nanostructured surface modification, is thus a promising approach to realize reliable multi-material joints in complex systems.

We apply principles of Gibbs phase plane chemistry to and across the entire ocean-atmospheric interface. Surface tension increments support a two dimensional, tangential pressure well known to determine rates of bulk gas, bubble, salt, spray and momentum transfer plus both sensible and latent heat fluxes. Hence it is worth asking whether tension mapping follows from current understanding of two dimensional composition. A history is provided dating back centuries and demonstrating that detrital organic macromolecules are central; subtle surfactant functional variation creates a microforcing field which dissipates turbulent energy at the sub-meter scale. Since we have just distributed major biopolymeric classes emitted as primary organic aerosol, further climate links can be established by considering full planar thermochemistry. Organic microlayer behaviors are reviewed with attention to confined, analog phase transitions among two dimensional “solid, liquid, (and) gaseous” states serving as elasticity indicators. We also discuss surfactant properties of general marine dissolved organic carbon, demonstrating that only proteins and lipids are capable of occupying significant local micro-area. The literature often suggests albumin and stearic acid as best proxies, and so we distribute their concentrations through multilevel global ecodynamic simulations. Consensus distributions are obtained in order to control adsorptive equilibria. Working from conservation of planar free energy, a parametric equation of state is devised relating excess coverage to the surface pressure-modulus. Constant settings for the proxy pair are drawn from laboratory study, and they successfully reproduce frequencies for surfactant solid-to-gas occurrence in ambient compression experiments. Functionally resolved organic measurements are rare and so we group them into super-ecological province tables showing that our bulk concentration estimates are reasonable. Outputs are then fed into a coverage-tension-elasticity code. Resulting contours traverse the critical range for piston velocity, bubble-spray and damping effects on either a regional or seasonal basis. There is also a possibility for widespread microlayer crystallization in polar seas. The concepts are a direct extension of our organic aerosol work, and the two approaches could be inserted into Earth System Models in tandem. Uncertainties in the logic are enumerated and include kinetic and thermochemical factors at multiple scales. But the problems are reducible through molecular modeling coupled to renewed laboratory and field study. Connections to marine colloids-gels, microlayer iron chelation, and linings of the ice channel network are discussed additionally.

A new method, the sessile drop accelerometry (SDACC) for the study and measurement of the interfacial energies of solid-liquid-gas systems, is tested and discussed in this study. The laboratory instrument and technique –a combination of a drop shape analyzer with high-speed camera and a laboratory drop tower- and the evaluation algorithms, were designed to calculate the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on the thermodynamic equilibrium of the system interfaces and not on the balance of bi-dimensional tensions on the solid-liquid-gas contour line. A comparison of the mathematical model that supports the method with the widely accepted Young`s equation is discussed in this study.

A radial basis function network (RBFN) method is proposed to reconstruct daily Sea surface temperatures (SSTs) with limited SST samples. For the purpose of evaluating the SSTs using this method, non-biased SST samples in the Pacific Ocean (10°N–30°N, 115°E–135°E) are selected when the tropical storm Hagibis arrived in June 2014, and these SST samples are obtained from the OISST products according to the distribution of AVHRR L2p SST and in-situ SST data. Furthermore, an improved nearest neighbor cluster (INNC) algorithm is designed to search the optimal hidden knots for RBFNs from both the SST samples and the background fields. Then the reconstructed SSTs from the RBFN method are compared with the results from the optimum interpolation (OI) method. The statistical results show that the RBFN method has a better performance of reconstructing SST than the OI method in the study, and the average RMSE is 0.48°C for the RBFN method, which is quite smaller than the value of 0.69°C for the OI method. Additionally, the RBFN methods with different basis functions and clustering algorithms are tested, and we discover that the INNC algorithm with multi-quadric function is quite suitable for the RBFN method to reconstruct SSTs when the SST samples are sparsely distributed.

This research paper presents a comprehensive study on the gasification of wheat straw pellets in a 10-kW fixed bed gasifier through a combination of Computational Fluid Dynamics (CFD) simulation and experimental validation. The developed 2D CFD model in ANSYS meshing simulates the gasification process in ANSYS Fluent software. The investigation evaluates key parameters such as equivalence ratio, higher heating value, and temperature distribution within the gasifier to enhance syngas production efficiency. The simulated results exhibit a noteworthy agreement with experimental data obtained from gasification. The impact of the equivalence ratio on gas production and lower heating value (LHV) is systematically explored, revealing that an equivalence ratio of 0.35 is optimal for syngas production. The resulting producer gas composition at this optimum condition includes CO (~27.67%), CH4 (~3.29%), CO2 (~11.09%), H2 (~11.09%), and N2 (~51%). The study further investigates the positive influence of reactor temperature on increasing syngas quantity while considering the uneven shape of the reactor and various thermal reactions affecting temperature, static pressure, velocity, and density. The findings contribute valuable insights to improve the efficiency of fixed-bed gasifiers, offering essential information on performance parameters for sustainable and optimized syngas production.

Catalyst with high catalytic activity and good stability are desirable in the electrocatalytic oxidation of glucose. Herein, Pt concave nanocubes with high-index facets (HIFs) supported by carbon black (Pt CNC/CB) are prepared through a hydrothermal method. The experimental results demonstrate that the peak current densities in different potential regions on the Pt CNC/CB anode are 0.22, 0.20, and 0.60 mA cm−2, respectively. The glucose oxidation reaction shows superior performances in basic and neutral conditions than in acid conditions. Better stability is achieved by Pt CNC/CB than Pt concave nanocubes (Pt CNCs). Abundant surface defects with low-coordinated atom numbers, such as the steps, kinks, and edges, are served as active sites in the electrocatalytic oxidation of glucose. With the addition of carbon black, the catalytic activity can be improved by facilitating the full exposure of the active surface defects on the HIFs of Pt CNCs. Moreover, to address the aggregation of Pt CNCs, caused by the high surface energy of HIFs, the introduction of carbon material is an effective way to preserve the HIFs, and thus enhance the stability of the catalyst. Hence, the prepared Pt CNC/CB electrocatalyst has great potential to be applied in the electrooxidation of glucose.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

Polyphosphate (polyP) accumulating organisms (PAOs) are the key agent to perform enhanced biological phosphorus removal (EBPR) activity, and intracellular polyP plays a key role in this process. Potential associations between EBPR performance and the polyP structure have been suggested, but are yet to be extensively investigated, mainly due to the lack of established methods for polyP characterization in the EBPR system. In this study, we explored and demonstrated that single-cell Raman spectroscopy (SCRS) can be employed for characterizing intracellular polyPs of PAOs in complex environmental samples such as EBPR systems. The results, for the first time, revealed distinct distribution patterns of polyP length (as Raman peak position) in PAOs in lab-scale EBPR reactors that were dominated with different PAO types, as well as among different full-scale EBPR systems with varying configurations. Furthermore, SCRS revealed distinctive polyP composition/features among PAO phenotypic sub-groups, which are likely associated with phylogenetic and/or phenotypic diversity in EBPR communities, highlighting the possible resolving power of SCRS at the microdiversity level. To validate the observed polyP length variations via SCRS, we also performed and compared bulk polyP length characteristics in EBPR biomass using conventional polyacrylamide gel electrophoresis (PAGE) and solution ³¹P nuclear magnetic resonance (³¹P-NMR) methods. The results are consistent with the SCRS findings and confirmed the variations in the polyP lengths among different EBPR systems. Compared to conventional methods, SCRS exhibited advantages as compared to conventional methods, including the ability to characterize in situ the intracellular polyPs at subcellular resolution in a label-free and non-destructive way, and the capability to capture subtle and detailed biochemical fingerprints of cells for phenotypic classification. SCRS also has recognized limitations in comparison with ³¹P-NMR and PAGE, such as the inability to quantitatively detect the average polyP chain length and its distribution. The results provided initial evidence for the potential of SCRS-enabled polyP characterization as an alternative and complementary microbial community phenotyping method to facilitate the phenotype-function (performance) relationship deduction in EBPR systems.

Nanofluids are a novel class of heat transfer fluid that plays a vital role in industries. In mathematical investigations, these fluids are modeled in terms of traditional integer-order partial differential equations (PDEs). It is recognized that traditional PDEs cannot decode the complex behavior of physical flow parameters and memory effects. Therefore, this article intends to study the mixed convection heat transfer in nanofluid over an inclined vertical plate via fractional derivatives approach. The problem in hand is modeled in connection with Atangana-Baleanu fractional derivatives without singular and local kernel having strong memory. The human blood is considered as base fluid dispersing carbon nanotube (CNTs) (single-wall carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes(MWCNTs )) into it to form blood-CNTs nanofluid. The nanofluids are considered to flow in a saturated porous medium under the influence of an applied magnetic field. The exact analytical expressions for velocity and temperature profiles are acquired using the Laplace transform technique and plotted in various graphs. The empirical results indicate that the memory effect decreases with increasing fractional parameters in the case of both temperature and velocity profiles. Moreover, the temperature profile is higher for blood-SWCNTs by reason of higher thermal conductivity whereas, this trend is opposite in case of velocity profile due densities difference.

Present work investigates, in photon energy domains of specific interest for medical imaging, the effect of the escape of X-ray fluorescence from the scintillator materials on the energy resolution of scintillation detector itself. Monolithic as well as pixelated crystals differently sized are considered, in the case of the NaI because it is the gold standard in the field. The volumetric ratio is introduced, as a figure of merit, taking into account, alongside the surface-to-volume ratio, the geometric shape, the elemental composition and also the mean-free-path for the given scintillator and energy. The inter-crystal XRF escape is finally suggested to be considered among the effects producing image blurring in segmented scintillatros due to the spread of events between the primary pixel and the first neighbors ones.

Background: This study introduces a novel dexamethasone (DEX) mixed micellar system (DEX-MM) using Soluplus® and Pluronic F-127 (PF127) to enhance ocular drug delivery. The enhancement of ocular application properties was achieved by creating a chitosan-coated DEX-MM (DEX-CMM), which promotes better adherence to the ocular surface, thereby improving drug absorption; Methods: Using the solvent evaporation method, a formulation was developed with a Soluplus® to drug ratio of 1:10, enhanced with 0.25% PF127. After dispersing in water, 1% chitosan (CS) was added. The stability and integrity of DEX within the micelles were verified using attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR) and differential scanning calorimetry (DSC). Additionally, in vitro and ex vivo drug release studies were con-ducted; Results: DEX-CMM (F6) demonstrated a particle size of 151.9±1 nm and a polydispersity index (PDI) of 0.168±0.003, suggesting uniformity and high electrostatic stability with a zeta po-tential of +35.96±2.13 mV. The non-Fickian drug release mechanism indicated prolonged drug retention. Comparative analyses showed DEX-CMM outperforming a standard DEX suspension in drug release and ocular tissue permeation, with flux measurements significantly higher than the DEX suspension; Conclusion: The study confirmed the efficacy of DEX-CMM in enhancing drug delivery to ocular tissues, evidenced by improved permeability. Safety evaluations using the HET-CAM test demonstrated that DEX-CMM was non-irritant, supporting its potential for effective ocular drug delivery.

The integration of supply chain data analytics with marketing strategies has become increasingly critical for organizations seeking to enhance customer insights and competitive advantage in today's dynamic business environment. This qualitative research explores the intersection of these two disciplines, focusing on implementation strategies, benefits, challenges, and future directions. Through semi-structured interviews with industry experts and stakeholders, key themes emerged, highlighting the importance of cross-functional collaboration, technological integration, and robust data governance in achieving effective integration. The study identifies significant benefits, including enhanced customer insights, improved operational efficiencies, and competitive advantage through personalized marketing strategies and optimized supply chain management. However, challenges such as data silos, technological complexities, and regulatory compliance issues pose barriers that require strategic solutions and organizational commitment. Future directions point towards the continued evolution of predictive analytics, AI-driven solutions, and sustainability integration, shaping the future landscape of supply chain management and marketing. Proactive engagement with regulatory frameworks and ethical considerations will be crucial in navigating these challenges and building trust with consumers. Ultimately, this research contributes to a deeper understanding of how organizations can leverage data analytics to drive strategic decision-making, enhance customer relationships, and achieve sustainable growth in an increasingly data-driven economy.

Three types of double perovskite La1-xPrxBa0.5Sr0.5Co1.5Fe0.5O5+δ(x=1,0.3,0) are prepared using the EDTA-citrate method and identified as solid oxide fuel cell (SOFC) cathodes. The microstructures, as well as electrochemical performances of La1-xPrxBa0.5Sr0.5Co1.5Fe0.5O5+δ (LPBSCF) and La2NiO4-impregnated LPBSCF (LN-LPBSCF) cathodes, are investigated in detail. An optimum impregnation amount of LN-LPBSCF (LN loading of 0.64 mg/cm2) electrode exhibits relatively lower electrode polarization resistance (Rp) and better stable performance as compared to that of pure LPBSCF electrode in symmetrical SOFCs. The maximum power density of LN-LPBSCF single cells is 800 mW/cm2 at 800 °C and demonstrates good stability for 100 h in short-term testing.

Laser-induced fluorescence spectroscopy (LIFS) is actively used for remote sensing of atmospheric aerosols and currently is one of the most sensitive and selective techniques for determining small concentrations of substances inside particles. The use of high-power femtosecond laser sources for LIFS-based remote sensing of aerosol contributes to the development of new-generation fluorescence atmospheric lidars since it makes it possible overcoming the energy threshold for the nonlinear-optical effects of multiphoton absorption in particles and receiving the emission signal at long distances in the atmosphere. Our study is aimed to the development and experimental demonstration the technique of nonlinear laser-induced fluorescence spectroscopy (NLIFS) based on the remote excitation of aerosol fluorescent emission stimulated by a spatially-structured high-power femtosecond laser pulse. Importantly, for the first time to our knowledge, we demonstrate the advances of using stochastically-structured plasma-free intense light channels (postfilaments) specially formed by propagation of femtosecond laser radiation through a turbulent air layer for improving NLIFS efficiency. A multiple increase in the received signal of two-photon-excited fluorescence of polydisperse dyed aqueous aerosol by the structured postfilaments is reported.

Many ailments can be diagnosed while they are asymptomatic, meaning that the patient has no signs or symptoms of a progressing disease. If caught in their initial stage of formation, these maladies can be effectively treated, leading to successful outcomes; curative therapies can halt illnesses from advancing, thus improving the quality of life, and long-term survival of the patient. Still cutting-edge upgrades in precision technologies are necessary for early, reliable, affordable, and rapid disease detection, but also are vital for the well-being of people and the future of global public health. The emerging role and utility of non-invasive and repeatable diagnostic test approaches for detection of health conditions has been liquid biopsies based on genomic biomarkers. As such, biological fluids permit any measurable molecular indicator or signature (e.g., proteins), to provide valuable information on individual’s wellness and/or disease. Among the bodily secretions used for non-invasive diagnostics is sputum, a complex viscous gel-like biopolymeric network, that has gained growing recognition as a rich source of biomarkers of airway infections, pulmonary diseases, and serves as a determinant to reveal other illnesses. As per the World Health Organization, the burden of respiratory conditions is exacerbated by factors, ranging from considerable subjection to air pollution and occupational contaminants, to tobacco smoking and second-hand smoke, in addition to poor socio-economic status. Due to the likely increase of these determinants, respiratory tract ailments are on the rise, affecting the health of many individuals, in addition to putting stress on healthcare facilities and services worldwide. We therefore highlight the need to use expectorated or induced sputum specimens as a routine sample source for testing valuable protein biomarkers to diagnose these chronic maladies, to predict inflammation and disease progression, as well as monitor the effectiveness of treatments. Further, we discuss the urgency for fast and reliable point-of-care methods to detect and quantify crucial protein biomarkers in sputum specimens, and limitations faced when dealing with their complex matrices.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

Up to 50% of patients with high-risk myeloid malignancies die of relapse after allogeneic stem cell transplantation. Current sequential conditioning regimens like the FLAMSA protocol combine intensive induction therapy with TBI or alkylators. Venetoclax has synergistic effects to chemotherapy. In a retrospective survey among German transplant centers, we identified 61 patients with myeloid malignancies that had received FLAMSA based sequential conditioning with Venetoclax between 2018 and 2022 as an individualized treatment approach. Sixty patients (98%) had active disease at transplant and 74% had genetic high-risk features. Patients received allografts from matched unrelated, matched related or mismatched donors. Tumor lysis syndrome occurred in two patients but no significant non-hematologic toxicity related to Venetoclax was observed. At day +30, 55 patients (90%) were in complete remission. Acute GvHD II°-IV° occurred in 17 (28%) and moderate/severe chronic GvHD in 7 patients (12%). Event-free survival and overall survival were 64% and 80% at 1 year as well as 57% and 75% at 2 years, respectively. The combination of sequential FLAMSA-RIC with Venetoclax appears to be safe and highly effective. To further validate these insights and enhance the idea of smart conditioning, a controlled prospective clinical trial has been initiated in 07/2023.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

Keywords: Artificial Neural Network (ANN), Support Vector Machine (SVM), Support Vector Regression (SVR), Lightweight Gradient Boosting Machines (Light GBM), Machine Learning, Solar Irradiance (SI), Solar forecasting

We report a diode pumped solid state (DPSS) laser used for intracavity pump-enhanced difference frequency generation (DFG) to create a 3.5 micron laser. Using a 50 mm-long periodically poled lithium niobate (PPLN) crystal inside the cavity of an Nd:YVO4 solid state laser at 1064 nm with 4.5 W pump power at 808 nm, and a 310 mW C-band signal at 1529 nm, up to 31 mW of mid-infrared output power at 3499 nm is obtained. The cavity requires no active stabilization and/or locking, and the entire cavity is &lt;8 cm in length. The obtained output power corresponds to a black box efficiency of 2.20 %W-1, which is the highest value reported to date for continuous wave DFG based on a bulk nonlinear optical crystal with no active stabilization. Potential future applications in free space optical communication are discussed as well.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

This paper introduces a novel algorithm for solving the point-to-point shortest path problem in a static regular 8-neighbor connectivity (G8) grid. This algorithm can be seen as a generalization of Hadlock algorithm to G8 grids, and is shown to be theoretically equivalent to the relaxed A* (RA*) algorithm in terms of the provided solution's path length, but with substantial time and memory savings, due to a completely different computation strategy, based on defining a set of lookup matrices. Through an experimental study on grid maps of various types and sizes (1290 runs on 43 maps), it is proven to be 2.25 times faster than RA* and 17 times faster than the original A*, in average. Moreover, it is more memory-efficient, since it does not need to store a G score matrix.

Abstract: The marketing of Sugar-Sweetened Beverages (SSBs) within grocers is an obesogenic factor that negatively impacts children’s nutritional behavior, specifically regarding people from racial and ethnic minority groups. We aimed to develop and employ a methodology that more precisely assesses the availability, price, and promotion of SSBs to young immigrant children within independently owned grocery stores. A case comparison design was used to explore the differences in the grocery store landscape of SSB marketing by conducting an enhanced Nutrition Environment Measures Survey-SSB (NEMS-SSB) within 30 grocery stores in the Hispanic and Latino enclaves in Southwest Detroit, in the Arab and Chaldean enclaves in North-central Detroit, and in Warren, Hamtramck, and Dearborn, in comparison with 48 grocers in Metro Detroit. Organic, plant-based, and unsweetened toddler and infant beverages, as well as questions about marketing, were added to the original NEMS-S to capture the promotion tactics used in marketing SSBs. NEMS-SSB scores revealed in the immigrant enclaves there was a significantly higher availability of SSBs in grocery stores (−2.38), and they had lower prices than those in the comparison group (−0.52). Availability of unsweetened and organic beverages was zero in 97% of all participating grocery stores. Signage featuring cartoon characters was the most frequent in-store SSB marketing tactic. Widespread SSB marketing towards toddlers within the grocery stores in immigrant enclaves could be linked with the higher childhood obesity prevalence among this population. Our findings can assist local and national organizations in developing and implementing healthy eating interventions. This study can be repeated in other states to provide comparable results.

To improve the monitoring of the electrical power grid it is necessary to evaluate the influence of contamination in relation to leakage current and its progression to a disruptive discharge. In this paper, insulators were tested in a saline chamber to simulate the increase of salt contamination on their surface, and to evaluate the supportability of these components. From the time series forecasting of the leakage current, it is possible to evaluate the development of the fault before a flashover occurs. Choosing which method to use is always a difficult task since some models may have higher computational effort. In this paper, for a complete evaluation, the long short-term memory (LSTM), group method of data handling (GMDH), adaptive neuro-fuzzy inference system (ANFIS), bootstrap aggregation (bagging), sequential learning (boosting), random subspace, and stacked generalization (stacking) ensemble learning models are analyzed. A review and comparison of these well-established methods for time series forecasting is performed. From the results of the best structure of the model, the hyperparameters are evaluated and the Wavelet transform is used to obtain an enhanced model.

We experimentally demonstrate enhanced self-phase modulation (SPM) in silicon nitride (Si₃N₄) waveguides integrated with 2D graphene oxide (GO) films. GO films are integrated onto Si₃N₄ waveguides using a solution-based, transfer-free coating method that enables precise control of the film thickness. Detailed SPM measurements are carried out using both picosecond and femtosecond optical pulses. Owing to the high Kerr nonlinearity of GO, the hybrid waveguides show significantly improved spectral broadening compared to the uncoated waveguide, achieving a broadening factor of up to ~3.4 for a device with 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of up to 18.4 and a Kerr coefficient (n₂) of GO that is about 5 orders of magnitude higher than Si₃N₄. Finally, we provide a theoretical analysis for the influence of GO film length, coating position, and its saturable absorption on the SPM performance. These results verify the effectiveness of on-chip integrating 2D GO films to enhance the nonlinear optical performance of Si₃N₄ devices.

Wireless Sensor Networks (WSNs) continue to provide essential services for various applications such as surveillance, data gathering, and data transmission from the hazardous environments to safer destinations. This has been enhanced by the energy-efficient routing protocols that are mostly designed for such purposes. Gateway-based Energy-Aware Multi-hop Routing protocol (MGEAR) is one of the homogenous routing schemes that was recently designed to more efficiently reduce the energy consumption of distant nodes. However, it has been found that the protocol has a high energy consumption rate, lower stability period, less data transmission to the Base station (BS). In this paper, an enhanced Heterogeneous Gateway-based Energy-Aware multi-hop routing protocol ( HMGEAR) is proposed. The proposed routing scheme is based on the introduction of heterogeneous nodes in the existing scheme, selection of the head based on the residual energy, introduction of multi-hop communication strategy in all the regions of the network, and implementation of energy hole elimination technique. Results show that the proposed routing scheme outperforms two existing ones.

To understand the enhanced protection mechanism of CoCrNiAlY-YSZ-LaMgAl11O19 dou-ble-layer ceramic coating with aluminum plating, a finite element simulation method was used to simulate the distribution of thermal stress in the coating in all directions. The results show that in the air exposure of the un-aluminized coating, high temperature causes a large radial thermal stress on the surface of the LaMgAl11O19 (LMA) layer, and it increases with the increase in temperature, which is the main reason for the initiation of axial cracks. After arc aluminum plating, the aluminum plating layer effectively inhibited the volume shrinkage of the coating through good adhesion to the coating and internal diffusion, the thermal stress of the coating was considerably reduced, and the CoCrNiAlY-YSZ-LMA coating had an effective enhancement and protection effect; however, there was still a certain amount of shear thermal stress inside the LMA layer, the top of the crack, and the bottom of the crack. This thermal stress caused the initi-ation of radial microcracks in the LMA layer, which also becomes a risk point for the failure of the aluminum coating.

The colossal depths of the deep neural network sometimes suffer from ineffective backpropagation of the gradients through all its depths. Whereas, The strong performance of shallower multilayer neural structures prove their ability to increase the gradient signals in the early stages of training which easily gets backpropagated for global loss corrections. Shallow neural structures are always a good starting point for encouraging the sturdy feature characteristics of the input. In this research, a shallow, deep neural structure called PrimeNet is proposed. PrimeNet is aimed to dynamically identify and encourage the quality visual indicators from the input to be used by the subsequent deep network layers and increase the gradient signals in the lower stages of the training pipeline. In addition to this, the layerwise training is performed with the help of locally generated errors which means the gradient is not backpropagated to previous layers, and the hidden layer weights are updated during the forward pass, making this structure a backpropagation free variant. PrimeNet has obtained state-of-the-art results on various image datasets, attaining the dual objective of (1) compact dynamic deep neural structure, which (2) eliminates the problem of backwards-locking. The PrimeNet unit is proposed as an alternative to traditional convolution and dense blocks for faster and memory-efficient training, outperforming previously reported results aimed at adaptive methods for parallel and multilayer deep neural systems.

In this study, a natural-based gelling agent comprised of blended flax seed gum (FSG), konjac glucomannan (KG), and agar gel (AG) was developed for application to control the textural properties of foods. The compound gels, including FSG, KG, and AG, were investigated to determine their physicochemical properties, including minimum gelling concentration, water binding capacity, water soluble index, and swelling power. In addition, we analyzed the rheological properties of the compound gel through texture analysis, frequency sweep, and creep and recovery. The microstructure of the compound gel was identified and compared with the viscoelastic properties of the gel. Overall, these results showed that the F4K6 (4:6:2 of FSG:KG:AG) could serve as an excellent gelling agent, which endowed food gel with the promoted elastic properties, water capacity, and rigid surface morphology. This work suggests that novel gelling agents, including FSG, KGM, and AG, successfully prepared food gels with improved physicochemical properties.

We report enhanced nonlinear optics in complementary metal-oxide-semiconductor (CMOS) compatible photonic platforms through the use of layered two-dimensional (2D) graphene oxide (GO) films. We integrate GO films with silicon-on-insulator nanowires (SOI), high index doped silica glass (Hydex) and silicon nitride (SiN) waveguides and ring resonators, to demonstrate an enhanced optical nonlinearity including Kerr nonlinearity and four-wave mixing (FWM). The GO films are integrated using a large-area, transfer-free, layer-by-layer method while the film placement and size are controlled by photolithography. In SOI nanowires we observe a dramatic enhancement in both the Kerr nonlinearity and nonlinear figure of merit (FOM) due to the highly nonlinear GO films. Self-phase modulation (SPM) measurements show significant spectral broadening enhancement for SOI nanowires coated with patterned films of GO. The dependence of GO’s Kerr nonlinearity on layer number and pulse energy shows trends of the layered GO films from 2D to quasi bulk-like behavior. The nonlinear parameter of GO coated SOI nanowires is increased 16 folds, with the nonlinear FOM increasing over 20 times to FOM > 5. We also observe an improved FWM efficiency in SiN waveguides integrated with 2D layered GO films. FWM measurements for samples with different numbers of GO layers and at different pump powers are performed, achieving up to ≈7.3 dB conversion efficiency (CE) enhancement for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. These results reveal the strong potential of GO films to improve the nonlinear optics of silicon, Hydex and SiN photonic devices.

BiVO4 powder was synthesized by a simple hydrothermal method. The nanobelts with well dispersed and uniform morphology were synthesized by controlling the temperature. The structure of BiVO4 powder was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The diameter of the nanobelts was about 50 nm. The structure and composition of the nanobelts were studied by X-ray diffraction (XRD), photoluminescence (PL) and X-ray photoelectron spectroscopy (XPS). The absorption intensity of BiVO4 powder in UV-Vis region was compared by UV–vis diffuse reflectance spectroscopy. As a photocatalyst, BiVO4 nanobelts have good photocatalytic ability under visible light irradiation, which is very useful for the treatment of environmental wastewater. The synthesized nanobelts photocatalyst can be reused without destroying its structure. The reusability and chemical stability of photocatalysts are of great significance for practical application.

A simple, effective and environmental-friendly method was adopted for enhancing the photocatalytic activity of g-C3N4 in the reduction of aqueous Cr(Ⅵ) under visible-light irradiation. The enhancement was achieved via treatment of g-C3N4 in organic solvent with addition of NaOH particles by ultrasonic process for two hours. The results demonstrated that the treated g-C3N4 exhibited much higher photocatalytic activity than pristine g-C3N4 in the reduction of Cr(VI) . Under visible light irradiation for 120 min, the reduced ratios of Cr(VI) with the initial concentration of 50 mg/L in the presence of the treated g-C3N4and pristine g-C3N4 were 100% and 37.1%, respectively. With the addition of fulvic acid, Cr(VI) was efficiently removed at 40 min. Based on the characterization results of the structures and other physiochemical properties of the treated g-C3N4 and pristine g-C3N4 by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and UV Vis diffuse reflectance, the possible reasons responsible for the enhanced photocatalytic activity of the treated g-C3N4 were proposed. The yield and mechanism of different exfoliation methods were compared by semi-quantitative method.

Dengue virus (DENV), the causative agent of dengue fever (DF), is one of the most important mosquito-borne viruses that can infect humans. Although much effort has been made on prevention and control of dengue, there are currently no anti-viral drugs or worldwide approved vaccines yet. In this study, we immunized six-week-old Balb/c mice with DNA vaccine candidates E and NS1-2a of DENV serotype 2 or the combination of them (E+NS1-2a) via an electroporation (EP)-assisted intramuscular gene delivery system and evaluated the immune response and protection. The highest specific antibody titres and cytokine levels secreted by splenocytes as well as the highest survival rate were observed in the E+NS1-2a group, followed by E group and NS1-2a group. Our data suggested that the combination of E and NS1-2a delivered by EP may be a superior preventive strategy against DENV.

Potassium-oxygen batteries (KOBs) are a promising energy storage technology with high theoretical en-ergy density, low overpotential and long cycle life. Cathode microstructure plays a significant role in the electrochemical performance of KOB. In this article, hierarchical porosity was introduced to commer-cially available carbon paper cathodes by the thermal pretreatment in air at different pretreatment times. This pretreatment modifies the properties, such as, surface area, defects, oxygen functional groups etc. and it has been found to enhance the discharge capacity and it result in reduction of dis-charge overpotentials.

The article presents a new method called slide roller burnishing (SRB) for cold working of cylindrical surfaces on machine tools, implemented with a novel multi-functional device. The machined material was chromium–nickel austenitic stainless steel. The deforming element is a toroidal roller whose axis crosses that of the workpiece. As a result, a relative sliding velocity occurs in the contact zone between the roller and the machined surface. The sliding velocity vector is set using the burnishing device. The theoretical background of SRB is presented. When the two axes are parallel, the well-known roller burnishing (RB) method is implemented. Thus, RB is a special case of SRB. Both processes are realized using the multi-functional burnishing device. The RB process was studied experimentally and optimized according to three criteria, based on the relationship between the surface integrity and operating behavio of the respective component, to achieve three processes: smoothing, hardening and mixed burnishing. Using the optimal RB parameters obtained, the dependence of the results of SRB on the crossing angle was investigated and optimized. A comparative analysis was performed between the optimized RB and SRB processes (respectively for their three variants: smoothing, hardening and mixed) based on geometrical and physical–mechanical characteristics of the surface integrity. The main advantage of the SRB is that it provides smaller height roughness parameters and a higher surface microhardness than RB.

Machining titanium alloy (Ti6Al4V) used in orthopedic implants by conventional metal cutting processes is challenging due to excessive cutting forces, low surface integrity and tool wear. To overcome these difficulties and for ensuring high-quality products, various industries employ wire electrical discharge machining (WEDM) for precise machining of intricate shapes in titanium alloy. The objective is to make WEDM machining parameters as efficient as possible for machining the bio-compatible alloy Ti6Al4V using box-behnken design (BBD) and Non-dominated Sorting Genetic Algorithm II (NSGA II). A quadratic mathematical model is created to represent the productivity and the quality factor (MRR and surface roughness) in terms of varying input parameters, such as pulse active (Ton) time, pulse inactive (Toff) time, peak amplitude (A) current and applied servo (V) voltage. The established regression models and related prediction plots provide a reliable approach for predicting how the process variables affect the two responses viz MRR and SR. The effects of four process variables on both the responses were examined, and the findings revealed that the pulse duration and voltage has a major influence on the rate at which material is removed (MRR) whereas pulse duration influence quality (SR).  The trade-off between MRR and SR, when significant process factors are included emphasizes the need for a reliable multi-objective optimization method. The intelligent metaheuristic optimization method named non-dominated sorting genetic algorithm II (NSGA II) is utilized to provide pareto optimum solutions in order to achieve high material removal rate (MRR) and low surface roughness (SR).

Powdery mildew disease, caused by Sphaerotheca fusca, is a major disease affecting cucumbers cultivated in greenhouses. This study was conducted to find defense genes induced by DL-3-amino-butyric acid (BABA) and powdery mildew in cucumber. The 2000 and 5000 mg/L BABA treated cucumber exhibited disease severity of 25% and 5%, respectively, whereas the water treated cucumber leaves were severely infected, with a disease severity of 90%. BABA did not effect spore germination of the powdery mildew pathogen,. showing BABA is not antifungal agent against the pathogen. In quantitative real-time PCR analysis, BABA treated cucumber upregulated transcriptional level of the defense genes CsPAL, CsPR3,CsPR1, CsLOX1, CsLOX23, Cs LecRK6.1, CsWRKY20, and Cupi4 in cucumber to maximum levels at 48 h, whereas CsLecRK6.1 reached maximum expression after 24 h and futher salicylic acid (SA) levels were significantly increased in BABA-treated cucumber plants. In addition, the infected cucumber with powdery mildew enhanced the expression levels from1.6 to 47.3 fold of the defense genes PAL, PR3, PR1, Lox1, Lox 23, LecRK6.1, WRKY20, and Cupi4 compared to heathy cucumber. The results suggests the BABA induced defense response is associated with SA signal pathway-dependent systemic acquired resistance (SAR) in cucumber, which is involved in plant resistance mechanisms.

Gabapentin (GBP) was originally developed as a potential agonist for Gamma-Amino-Butyric-Acid (GABA) receptors, aiming to inhibit the activation of pain-signaling neurons. Contrary to initial expectations, it does not bind to GABA receptors. Instead, it exhibits several distinct pharmacological activities, including: (1) binding to the alpha-2-delta protein subunit of voltage-gated calcium channels in the central nervous system, thereby blocking the excitatory influx of calcium; (2) reducing the expression and phosphorylation of CaMKII via modulation of ERK1/2 phosphorylation; (3) inhibiting glutamate release and interfering with the activation of NMDA receptors; (4) enhancing GABA synthesis; (5) increasing cell-surface expression of δGABA_A receptors, contributing to its antinociceptive, anticonvulsant, and anxiolytic-like effects. Additionally, GBP displays (6) inhibition of NF-kB activation and subsequent production of inflammatory cytokines, and (7) stimulation of the purinergic adenosine A1 receptor, which supports its anti-inflammatory and wound-healing properties. Initially approved for treating seizures and postherpetic neuralgia, GBP is now broadly used for various conditions, including psychiatric disorders, acute and chronic neuropathic pain, and sleep disturbances. Recently, as an eye drop formulation, it has also been explored as a therapeutic option for ocular surface discomfort in conditions such as dry eye, neurotrophic keratitis, corneal ulcers, and neuropathic ocular pain. This review aims to summarize the evidence supporting the molecular effects of GBP, with a special emphasis on its applications in ocular surface diseases.

Friction stir welding (FSW) is a solid state welding process for joining metallic alloys and dissimilar metals. It has emerged as an alternative technology for welding high strength alloys that are difficult to join with conventional techniques. FSW is used to produce products with better mechanical properties. Now a days aluminum alloys have been widely used in several industrial applications such as aerospace, marine, automobile and commercial applications due to their light weight structure, better mechanical properties and high corrosion resistance.In this work, three welding parameters such as spindle speed, welding speed and plunge depth were considered for friction stir welding. FSW was carried out between dissimilar aluminum alloy plates (AA6061 and AA 8011) to produce butt joint.A Box-Behnken design with three factors and three levels was chosen to minimize the number of experimental conditions .The tensile strength and hardness of the welded regions were evaluated. The optimum level settings and the major parameters that influence the joint strength were obtained by Box-Behnken design.

Three-dimensional flexible piezoresistive porous sensors have been used in health diagnosis and wearable devices. By utilizing 3D printed sacrificial mold casting with highly conductive polymer composites, porous sensors with high conductivity and complex structures were achieved. Traditional conductive polymer composites are usually heated using external heat sources, which are time and energy consuming. However, in this study, conductive porous sensors with triply periodic minimal surface (TPMS) structures were manufactured using self-resistance electric heating by utilizing the conductive nature of the polymers. The porous structures were designed based on Diamond (D), Gyroid (G), and I-WP (I) unit cells of the TPMS. The use of self-resistance electric heating has improved the compression performance and piezoresistive response of the structures. Among these structures, the D-based structure exhibited the maximum response strain (61 %), with a corresponding resistance response value of 0.97, which increased by 10.26 % compared to that of the structures heated by using the external heat sources. This study offers a new perspective on designing and optimizing porous materials with specific functionalities, particularly in the realm of flexible and portable piezoresistive sensors.

In permafrost regions, ground surface deformations induced by freezing and thawing threaten the integrity of the built environment. Mapping the frost susceptibility of the ground at a high spatial resolution is of practical importance for the construction and planning sectors. We processed Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) data from thawing seasons 2015 to 2019, acquired over the area of Ilulissat, West Greenland. We used a least-squares inversion scheme to retrieve the average seasonal displacement (S) and long-term deformation rate (R). We secondly investigated two different methods to extrapolate active layer thickness (ALT) measurements, based on their statistical relationship with remotely-sensed surface characteristics. A Generalized Linear Model (GLM) was first implemented, but the model was not able to fit the data and represent the ALT spatial variability over the entire study domain. ALT were alternatively averaged per vegetation class, using a land cover map derived by supervised classification of Sentinel-2 images. We finally estimated the active layer ice content and used it as a proxy to map the frost susceptibility of the ground at the community scale. Fine-grained sedimentary basins in Ilulissat were typically frost susceptible and subject to average seasonal downward displacements of 3 to 8 cm. Areas following a subsiding trend of up to 2.6 cm/yr were likely affected by permafrost degradation and melting of ground ice below the permafrost table. Our approach enabled us to identify frost-susceptible areas subject to severe seasonal deformations, and/or long-term subsidence induced by degrading permafrost. Used in combination with traditional site investigations, InSAR maps provide valuable information for risk management and community planning in the Arctic.

The topography and chemical composition modification of the titanium (Ti) implants play a decisive role in improving biocompatibility and bioactivity, accelerating osseointegration, and, thus, determining clinical success. In spite of the development of surface modification strategies, bacterial contamination is a common cause of failure. The use of systemic antibiotic therapy does not guarantee action at the contaminated site. In this work, we proposed a surface treatment for Ti implant that aim to improve its osseointegration and reduce bacterial colonization in surgery site due to local release of antibiotic. The Ti disks were hydrothermally treated with 3M NaOH solution to form a nanostructured layer of titanate on the Ti surface. Metronidazole was impregnated on these nanostructured surfaces to allow its local release. The samples were coated with poly(vinyl alcohol) - PVA films with different thickness to evaluate a possible control of drug release. Gamma irradiation was used to crosslink the polymer chains leading to a hydrogel layer formation and to sterilize the samples. The samples were characterized by XRD, SEM, FTIR, contact angle measurements, “in vitro” bioactivity, and drug release analysis. The alkaline hydrothermal treatment successfully produced intertwined, web-like nanostructures on the Ti surface, providing wettability and bioactivity to Ti samples (Ti+TTNT samples). Metronidazole was successfully loaded and released from Ti+TTNT samples coated or not with PVA. Although the polymeric film acted as a physical barrier to drug delivery, all groups reached the minimum inhibitory concentration for anaerobic bacteria. Thus, the surface modification method presented is a potential approach to improve the osseointegration of the Ti implant and to associate local drug delivery to dental implants, preventing early infections and bone failure.

Study of gross alpha (GA) and gross beta (GB) activity in road and surface deposited sediments were performed in various geographical areas in three Russian cities. To perform radiation measurements, new methods were applied which allow dealing with low mass and low volume dust size (2-100μm) samples obtained after the size fractionation procedure. The 2-10 μm fraction size has the highest gross beta activity concentration (GB)– 1.32Bq/g in Nizhny Novgorod (NN) and Rostov-On-Don (RND) while the 50-100 μm fraction size in Ekaterinburg. This is maybe associated with the subsistence of radionuclides that conveyed through natural processes and anthropogenic applications. The highest gross alpha activity concentration (GA) in fraction sizes was found in Rostov-on-Don city within the 50-100 μm– 0.22Bq/g. The fraction size 50-100 μmhas a higher gross alpha activity concentration than 2-10 and 10-50 μmfraction sizes due to natural partitioning of the main minerals constituting the urban surface deposited sediment (USDS). The geochemical processes that occur during the formation and transportation of USDS are reflected in the observed dependencies.Developed experimental methods of radiation measurements allowed to the extent the methodological base of urban geochemical studies.

rdinary people and political leaders must know the sources of greenhouse gas emissions and their effect on global climate change before they have ability to make decisions to reduce emissions and increase sinks of these gases. These people must, however, understand where greenhouse gas emissions are formed and how reductions can be made: they must understand where carbon dioxide sinks are and how to preserve or increase these sinks. North Savo is the example used in this work to describe the present emissions and sinks. There are proposals on what should and could be done to reduce greenhouse gas emissions caused by traffic, heating, forests and agriculture. There are possibilities of reducing emissions of greenhouse gases in traffic and heating in spite of the fact that the province has a low population density with long distances between homes and workplaces and schools, and a cold climate. We believe that research will also find solutions for reducing greenhouse gases and protecting waters, which are used for recreational purposes and for raw water of drinking water in many places. Luckily forests cover large areas of North Savo and their growth is an important carbon dioxide sink. In addition, forest soils serve as a valuable storage of carbon. Besides carbon dioxide emissions, emissions of nitrous oxide and methane must also be considered since they are more potent greenhouse gases than carbon dioxide and land use can thus influence these gas emissions.

Streptococcus mutans is well known for having virulence factors associated with its cariogenic role, such as glucosyltransferases, which have been used as targets for the virtual screening of molecules with inhibitory capacity. The Antigen I/II of S. mutans is involved in the adhesion to the surface of the tooth and the bacterial co-aggregation in the biofilm formation, despite that, this protein has not been used as a target in a virtual strategy search for inhibitors. In this study we identified in silico and evaluated in vitro molecules with adhesion inhibitory potential on S. mutans Ag I/II. A virtual screening of 883,551 molecules was conducted, cytotoxicity analysis on fibroblast cells, S. mutans adhesion studies, scanning electron microscopy analysis for bacterial integrity, and molecular dynamics simulation were also performed. We have found three molecules (ZI-187, ZI-939, ZI-906) that were not cytotoxic and inhibited the adhesion of S. mutans to polystyrene microplates. Molecular dynamic simulation by 300 nanoseconds showed stability of the interaction between ZI-187 and Ag I/II (PDB: 3IPK). This work provides three new molecules that targets Ag I/II and have the capacity to inhibit in vitro the S. mutans adhesion on polystyrene microplates and provides a new computational line for the search and selection of safe inhibitory molecules against different pathogens.

Air pollution has become the world’s single biggest environmental health risk of the past decade, causing about 7 million yearly deaths worldwide. One of the dominant air pollutants is fine particulate matter (PM2.5), a product of combustion. Exposure to PM2.5 has been associated with decreased lung function, impaired immunity, and exacerbations of lung disease. Accumulating evidence suggests that many of the adverse health effects of PM2.5 exposure are associated with lung inflammation and oxidative stress. While the physical structure and surface chemistry of PM2.5 are surrogate measures of particle oxidative potential, little is known about their contributions to negative health effects. In this study, we used functionalized carbon black particles as surrogates for atmospherically aged combustion formed soot to assess the effects of PM2.5 surface chemistry in lung cells. We exposed the BEAS-2B lung epithelial cell line to different soot at a range of concentrations, and assessed cell viability, inflammation, and oxidative stress. Our results indicate that exposure to soot with varying particle surface composition results in differential cell viability rates, expression of pro-inflammatory and oxidative stress genes, and protein carbonylation. We conclude that particle surface chemistry, specifically oxygen content, in soot modulates lung cell inflammatory and oxidative stress responses.

Rapid and extensive urbanization has adversely impacted humans and ecological entities in the recent decades through a decrease in surface permeability and the emergence of urban heat islands (UHI). While detailed and continuous assessments of surface permeability and UHI are crucial for urban planning and management of landuse zones, they have mostly involved time consuming and expensive field studies, and single sensor derived large scale aerial and satellite imageries. We demonstrated the advantage of fusing imageries from multiple sensors for landuse and landcover (LULC) change assessments as well as for assessing surface permeability and UHI emergence in Tirunelveli, Tamilnadu, India. Cartosat-2 and Landsat-7 ETM+ imageries from 2007 and 2017 were fused and classified using a Rotation Forest (RF), while surface permeability and temperature were quantified using Soil-Adjusted Vegetation Index (SAVI) and Land Surface Temperature (LST) index, respectively. Fused images exhibited higher classification accuracies than non-fused images, i.e. overall kappa coefficient values 0.83 and 0.75, respectively. We observed an overall increase of 20 km2 (45%) in the coverage of urban (dry, real estate plots and built-up) areas, while a decrease of 27 km2 (37%) for vegetated (cropland and forest) areas in Tirunelveli between 2007 and 2017. The SAVI values indicated an extensive decrease in surface permeability for Tirunelveli overall (0.4) and also for almost all LULC zones. The LST values exhibited an associated overall increase (1.30C) of surface temperature in Tirunelveli with the highest increase (2.40C) for urban built-up areas between 2007 and 2017. The SAVI-LST combined metric depicted the Southeastern built-up areas in Tirunelveli as a potential UHI hotspot, while a caution for the Western riparian zone for UHI emergence in 2017. Our results provide important metrics for surface permeability and UHI monitoring, and inform urban and zonal planning authorities about the advantages of satellite image fusion.

The aim of this study is to investigate, by means of experimental measurements and full-wave simulations, the dominant factors for the very high-resolution (VHR) radar image speckles from exponential correlated rough surfaces. A Ka-band radar system was used to collect the return signal from such a surface sample fabricated by 3D printing, and that signal was further processed into images at different resolution scales, where the image samples were obtained by horizontally turning around the surface sample. To cross-validate the results and to further discuss the VHR speckle properties, full wave simulations by full 3D Finite Difference Time Domain (FDTD) method were conducted with 1600 realizations for the speckle analysis. At the considered very high resolution, speckle statistics show divergence from the fully developed Rayleigh distribution. The factors that impact on the high-resolution speckle properties from exponential correlated rough surface, are analyzed in views of the equivalent number of scatterers theory and scattering scales, respectively. From the data results and extended discussions, it is evident that both of the above factors matter for VHR speckle of backscattering, from the exponential correlated rough surface as a good representative for the ground surface.

Impervious surface mapping with high-resolution remote sensing imagery has attracted increasing interest as it can provide detailed information for urban structure and distribution. Previous studies have suggested that the combination of LiDAR data and high-resolution imagery for impervious surface mapping performs better than using only high-resolution imagery. However, due to the high cost of the acquisition of LiDAR data, it is difficult to obtain the multi-sensor remote sensing data acquired at the same acquisition time for impervious surface mapping. Consequently, real landscape changes between multi-sensor remote sensing data at different acquisition times would lead to the error of misclassification in impervious surface mapping. This issue has mostly been neglected in previous works. Furthermore, the observation differences generated from multi-sensor data, including the problems of misregistration, missing data in LiDAR data, and shadow in high-resolution images would also challenge the final mapping result in the fusion of LiDAR data and high-resolution images. In order to conquer these problems, we propose an improved impervious surface mapping method incorporating both LiDAR data and high-resolution imagery at different acquisition times in consideration of real landscape changes and observation differences. In the proposed method, a multi-sensor change detection by supervised multivariate alteration detection is employed to obtain changed areas and misregistration areas. The no-data areas in the LiDAR data and the shadow areas in the high-resolution imagery are extracted by independent classification yielded by its corresponding single sensor data. Finally, an object-based post-classification fusion is proposed to take advantage of independent classification results with single-sensor data and the joint classification result with stacked multi-sensor data. Experiments covering the study site in Buffalo, NY, USA demonstrate that our method can accurately detect landscape changes and obviously improve the performance of impervious surface mapping.

Co-delivery of antigens and adjuvants to the same antigen presenting cells (APCs) can significantly improve the efficacy and safety profiles of vaccines. Here, we report amine-grafted silica nanoparticles (A-SNPs) as a tunable vaccine co-delivery platform for TLR7/8 agonists along with the recombinant influenza antigen hemagglutinin H7 (H7) to APCs. A-SNPs of two different sizes (50 and 200 nm) were prepared and coated with INI-4001 at different coating densities, followed by co-adsorption of H7. Both INI-4001 and H7 showed &gt; 90% adsorption to the tested A-SNP formulations. TNF-α and IFN-α cytokine release by human peripheral blood mononuclear cells as well as TNF-α, IL-6, and IL-12 release by mouse bone marrow-derived dendritic cells revealed that the potency of the INI-4001-adsorbed A-SNPs (INI-4001/A-SNP) formulations can be improved relative to aqueous formulation control. This improved potency was dependent on particle size and ligand coating density. In addition, slow-release profiles of INI-4001 were measured from INI-4001/A-SNP formulations in plasma with 30-50% INI-4001 released after 7 days. In vivo murine immunization studies demonstrated significantly improved H7-specific humoral and Th1/Th17-polarized T cell immune responses with no observed adverse reactions. Low-density 50 nm INI-4001/A-SNP elicited significantly higher IFN-γ and IL-17 induction over that of the H7 antigen only group and INI-4001 aqueous formulation controls. In summary, this work introduces an effective and biocompatible SNP-based co-delivery platform that enhances the immunogenicity of TLR7/8 agonist-adjuvanted subunit influenza vaccines.

Recently, significant progress has been made in developing computer-aided diagnosis (CAD) systems for identifying glaucoma abnormalities using fundus images. Despite their drawbacks, methods for extracting features such as wavelets and their variations, along with classifier like support vector machines (SVM), are frequently employed in such systems. This paper introduces a practical and enhanced system for detecting glaucoma in fundus images. This system adresses the chanallages encountered by other existing models in recent litrature. Initially, we have employed contrast limited adaputive histogram equalization (CLAHE) to enhanced the visualization of input fundus inmages. Then, the discrete ripplet-II transform (DR2T) employing a degree of 2 for feature extraction. Subsequently, a golden jackal optimization algorithm (GJO) employed to select the optimal features to reduce the dimension of the extracted feature vector. During the classification stage the least square support vector machine (LS-SVM) with three kernels called as linear, polynomial and radial basis function(RBF), for classifying of fundus images as glaucoma or healthy. The proposed method is validated with the current state-of-the-art models on two standard datasets, namely, G1020 and ORIGA. The results obtained from our experimental result demonstrate that our best suggested approach DR2T+GJO+LS-SVM-RBF obtains better classification accuracy 93.38% and 97.31% for G1020 and ORIGA dataset with less number of features. It establishes a more concise network structure when contrasted with traditional classifiers.

The present work describes the synthesis, characterization and photomineralization activity of synthesized Ce1-xZnxO2-x solid solution catalysts allowing the degradation of Diclofenac as a model of anti-inflammatory medicines in water. Oxygen deficient photocatalysts Ce1-xZnxO2-x (CeZnx), produced with mixing ZnO and CeO2 have been characterized for their crystallographic parameters, specific surface area and morphology. Photomineralization activity determinations using TOC analysis have shown efficient diclofenac photooxidation under sunlight. Moreover, results indicate that coexistence of Zn2+, Ce4+ and oxygen vacancies rate in CeZnx solid solution are key factors for strong drug mineralization. Finally, CeZn0.1 which is one of the photocatalysts synthesized in the present work represents a cheap and efficient reagent for organic matter photomineralization in wastewater.

The flavin derivatives 10‐methyl‐isoalloxazine (MIA) and 6-fluoro-10-methyl-isoalloxazine (6F-MIA) were encapsulated in two alternative metal-organic frameworks, (MOFs) MIL53(Al) and MOF5, using a post-synthetic, diffusion-based incorporation into microcrystalline MIL-53 powders and an in-situ approach during the MOF-5 synthesis. The flavin@MOF composites were analyzed by powder X-ray diffractometry (PXRD), N2-sorption studies and time-resolved fluorescence spectroscopy and microscopy. The maximum amount of flavin dye incorporation is 3.9 wt% for MIA@MIL-53(Al) and 1.5 wt% for 6F-MIA@MIL-53(Al), 0.85 wt% for MIA@MOF-5 and 27.6 wt% for 6F-MIA@MOF-5. The emission wavelengths of all flavin@MOF composites mostly correspond to the wavelengths of the flavins in solution. Time-resolved spectroscopy showed that the fluorescence lifetime of flavin@MOF of 2-4.7 ns also corresponds to those in solution but is significantly prolonged compared to the solid flavin dyes with less than 1 ns, thereby confirming the concept of "solid solutions" for dye@MOF composites. The fluorescence quantum yield (ΦF) of the flavin@MOF composites is about half of the solution but is significantly higher compared to the solid flavin dyes. Both the fluorescence lifetime and quantum yield of flavin@MOF decrease with the flavin loading in MIL-53. Theoretical calculations using plane-wave and QM/MM methods are in good correspondence with the experimental results and explain the electronic structures as well as the photoluminescence/photophysical properties of crystalline MIA and the flavin@MOF composites. In the solids flavins π-stacking interactions of the molecules lead to a charge transfer state with low oscillator strength resulting in aggregation-caused quenching (ACQ) with low lifetimes and quantum yields. In the MOF pores the flavin molecules are separated and the computed MIA@MOF structures do not find π-stacking interactions to the pore walls but only weak van-der-Waals contacts which reasons the enhanced fluorescence lifetime and quantum yield of the flavins in the composites compared to their neat solid state. The flexible MOF MIL-53(Al) was optimized essentially to the experimental large-pore form in the guest-free state with QuantumEspresso (QE) and with MIA molecules in the pores the structure contracted to close to the experimental narrow-pore form which was also confirmed by PXRD. In summary, the incorporation of flavins in MOFs yields solid-state materials with enhanced rigidity, stabilized conformation and reduced aggregations of the flavins, leading to increased fluorescence lifetime and quantum yield as controllable photo-luminescent and photo-physical properties.

The thermoelectric generator (TEG) stands out in many energy harvesters due to its simple structure, small size, etc. However, previous studies rarely probe into the influence of TEG internal resistances on extracting maximum power from TEG, and tracking efficiency is limited. By analyzing the relationship between the tracking efficiency and the TEG internal resistances, a time exponential rate perturbation and observation (P&amp;O) technology is proposed to achieve maximum power point tracking (MPPT) for a wide resistance range of TEG. Using the time exponential rate P&amp;O, the MPPT circuit observes the power change by comparing PMOS on-time and perturbs the power by adjusting NMOS on-time exponentially. The MPPT circuit is implemented in a 110nm CMOS process. The tracking efficiency keeps a high level from 98.9 to 99.5%. The applicable range of the TEG resistance is from 1 to 12Ω, which is enhanced at least 2.2 times.

Autophagy, an alternative cell death mechanism, is also termed programmed cell death type II. Autophagy in cancer treatment needs to be regulated. In our study, autophagy inhibition by desipramine or the autophagy inhibitor chloroquine (CQ) enhanced tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) receptor-2 [death receptor (DR5)] expression and subsequently TRAIL-induced apoptosis in TRAIL-resistant A549 lung cancer cells. Genetic inhibition of DR5 substantially reduced desipramine-enhanced TRAIL-mediated apoptosis, proving that DR5 was required to increase TRAIL sensitivity in TRAIL-resistant cancer cells. Desipramine treatment upregulated p62 expression and promoted conversion of light chain 3 (LC3)-I to its lipid-conjugated form, LC3-II, indicating that autophagy inhibition occurred at the final stages of autophagic flux. Transmission electron microscopy analysis showed the presence of condensed autophagosomes, which resulted from the late stages of autophagy inhibition by desipramine. TRAIL, in combination with desipramine or CQ, augmented the expression of apoptosis-related proteins cleaved caspase-8 and cleaved caspase-3. Our results contributed to the understanding of the mechanism underlying the synergistic anti-cancer effect of desipramine and TRAIL and presented a novel mechanism of DR5 upregulation. These findings demonstrated that autophagic flux inhibition by desipramine potentiated TRAIL-induced apoptosis, suggesting that appropriate regulation of autophagy is required for sensitizing TRAIL-resistant cancer cells to TRAIL-mediated apoptosis.

This paper addresses the capability to alter the hydrophilic wettability characteristics of poly(vinyl alcohol) (PVA) polymer films doped with glycerol. Films of PVA and glycerol-choline chloride (GCC) blends have been prepared using the solution casting method with different glycerol dopants ranging from 0% to 10% (wt %). The results show that as the GCC dopant content increases from 0% to 10%, the wettability increases, thus increasing the surface energy of the solid film. The wettability changes are observed by identifying the contact angle of 10 µL deionized water droplet which altered from 55^o to 28^o as dopant content changed from 0% to 10% per PVA solution weight. The results show that the roughness of film surfaces increases as the content of dopant (GCC) increases in the film indicating that roughness has a strong influence on the wettability of the casted films.

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.

Surface–subsurface soil-rock modeling is crucial for infrastructure design and groundwater yield optimization, especially in the complex crystalline basement terrains of Penang Island, Malaysia. This study conducted large-scale characterization of soil-rock profiles using ERT, SRT, rock quality designation, and soil penetration test (SPT N-values) data, optimized through regression modeling. The approach effectively identified soil-rock structures and their suitability to prevent structural failures and enhance groundwater productivity. Correlations between borehole lithologic logs and velocity–resistivity models revealed distinct soil compositions across the study area. The results highlighted thick, saturated, and loose silty to sandy bodies in the eastern to northern sections, contrasting with sandy compositions and penetrative fractures in the southern part. The study also found good correlations between rock mass quality and N-values for different soil types. Depths of intra-bedrock weathered/fractured units varied between 12 and >35 m. This has significant implications for determining optimal foundation depths in the study area. Groundwater productivity was associated with intra-bedrock planes of weakness at depths exceeding 40 m. Overall, this study developed empirical relations between geophysical and geotechnical parameters for wet tropical granitic terrains, filling critical gaps in understanding subsurface characteristics.

Under the extreme shortage of water resources in the Yellow River Basin, it is of great signifi-cance to analyze the spatial distribution relationship between rural settlement and water re-sources for the coordinated development of human and water resources in the Yellow River Ba-sin. However, the water allocation scheme depended on statistical data in the previous work, not on rural settlements in space. Furthermore, previous researches seldom focus on the evaluation of surface water resources accessibility according to the spatial distribution characteristics of ru-ral settlements and water resources, especially, in the Yellow River Basin and using rural set-tlement as unit. Therefore, a quantitative evaluation model of surface water resources accessibil-ity is constructed by using the GIS network analysis method, taking rural settlement as the re-search unit, based on three dimensions of topography, distance, and surface water resources, at the Yellow River basin scale. The results show that: (1) The surface runoff of rural settlement in the Yellow River basin is mostly less than 0.05 km/m2, reaching 99.83%. In other words, the Yel-low River Basin is extremely short of water resources. The surface water resources accessibility is affected by distance, topography, and surface water resources. The evaluation results show that the range of surface water resources accessibility is 0.13~0.88, with an average value of 0.47 and a standard deviation of 0.05. The High surface water resources accessibility value in the Yel-low River Basin is in the east and west, and the low value is mainly distributed in the middle. (2) The range from low to high of surface water resources accessibility in 12 catchments is Sanmen-xia station, Lanzhou station, Shizuishan station, Longmen station, Tongguan station, Toudaoguai station, Xiaolangdi station, Huayuankou station, Lijin station, Gaocun station, Ai Shan station and Tangnaihai station. (3) The value of surface water resources accessibility at the city scale is higher in the east of 10 cities and in the west of 1 city. However, it is lower in the west of 9 cities. And the values of the other cities are at a medium level. The correlation coefficient with primary industry GDP and surface water resources accessibility is 0.271 (N=56, Sig=0.043, in 0.05 level, the correlation is significant), which verifies the rationality of surface water resources accessibility model to some extent.

In addition to changes in the amount of rain, changes in land use upstream are considered a factor that directly affects the maximum runoff flow in a basin, especially in areas that have experienced floods and flash floods. This research article presents the application of the SWAT model to assess runoff in areas that have experienced flash floods, in order to analyze the proportion of land use change to the maximum runoff. Study areas that had experienced flash floods were in 3 basins in Thailand (Lam Saphung Basin, Phrom River Basin, and Chern River Basin Part 1 which is a subbasin of the Nam Chi River Basin). This study analyzed two main factors that influence runoff in the river basin: Changes in rainfall and changes in land use by considering 2 simulation situations.: (1) Changes in land use affecting runoff assessed by considering land use maps in 2006, 2008, 2010, 2015, 2017, 2019, and 2021 when using rainfall data only in the year 2021 for all cases, and (2) Changes in the amount of rainfall influencing runoff by considering the rainfall record in 2006, 2008, 2010, 2015, 2017, 2019, and 2021 when using the land use data only in the year 2021 for all cases. The results of the study found that the SWAT model can be effectively applied to estimate annual runoff in areas that have experienced flash floods under 8 parameters with R2 values of 0.74, 0.82 and 0.74 for the Lam Saphung River Basin and the Phrom River Basin and the Chern River Basin Part 1 respectively. In addition, it was found that the proportion of land use changes that involved changes from forest areas to residential areas was the greatest from 2008 to 2010 in the Phrom River Basin and Chern River Basin Part 1. This resulted in an increase in the maximum runoff amount of 77.78% and 46.87%, respectively. When land use was constant, it was found that the rainfall in 2010, which was the highest, also had the greatest impact on the runoff in all 3 areas.

Advanced methods of treatment are needed to fight the threats of virus-transmitted deseases and pandemics. Often they are based on an improved biophysical understanding of virus replication strategies and processes in their host cells. For instance, an essential component of the replication of the Hepatitis C virus (HCV) proceeds under the influence of non-structural HCV proteins (NSPs) that are anchored to the endoplasmatic reticulum (ER), such as the NS5a protein. The diffusion of NSPs has been studied by in-vitro fluorescence recovery after photobleaching (FRAP) experiments. The diffusive evolution of the concentration field of NSPs on the ER can be described by means of surface partial differential equations (sufPDE). Knodel et al, Viruses 2018, 10, 28 estimated the diffusion coefficient of the NS5a protein by minimizing the discrepancy of an extended set of sufPDE simulations and experimental FRAP time series data. Here, we provide a scaling analysis of the sufPDEs that describe the diffusive evolution of the concentration field of NSPs on the ER. This analysis provides an estimate of the diffusion coefficient that is based only on the ratio of the membrane surface area in the FRAP region and its contour length. The quality of this estimate is explored by comparison to numerical solutions of the sufPDE for a flat geometry and for ten different 3D embedded 2D ER grids that are derived from fluorescence z-stack data of the ER. Finally, we apply the new data analysis to the experimental FRAP time-series data analyzed in our previous paper, and we discuss the opportunities of the new approach.

Cirrus thinning, as one kind of geoengineering approach, not only cools our planet but also enhances the amount of sunlight reaching Earth's surface (brightening effect). This study delves into the brightening effect induced by cirrus thinning with a flexible seeding method. The thinning of only cirrus clouds results in a considerable globally averaged cooling effect (−2.46 W m−2), along with a notable globally averaged brightening effect (2.19 W m−2). Cirrus thinning also results in substantial reductions in the cloud radiative effects of the lower mixed-phase and liquid clouds. While these reductions counteract the cooling effect from cirrus clouds, they enhance the brightening effect from cirrus clouds. Consequently, the brightening effect caused by cirrus seeding (4.69 W m−2) is considerably more potent than its cooling effect (−1.21 W m−2). Furthermore, due to the more pronounced changes from the mixed-phase and liquid clouds at low- and mid-latitudes, the cooling effect is primarily concentrated at high latitudes. In contrast, the brightening effect is significantly stronger over most low- and mid-latitude regions. Overall, cirrus thinning could lead to a notable brightening effect, which can be leveraged to offset the dimming effect (the opposite of brightening effect) of other geoengineering approaches.

Despite much published literature on the impacts of agriculture on water quality, knowledge gaps persist regarding which farming systems are of most concern for these relationships, which could help water resource planners better target water management efforts. This study addresses these subjects, seeking to understand how this relationship varies across different farming systems. We used data on water quality status in watersheds of an agricultural region in southern Portugal and crossed it with a map of farming systems for the same region provided by a previous study. By overlaying both data layers, we characterized the areal shares of the farming systems in the watersheds and inspected how these shares relate with water quality status through logistic regression. Results support that the impact of agriculture on water quality is mostly related with specific farming systems. We believe this type of information can be of high interest for agricultural planners and policymakers interested in meeting water quality standards, and we conclude by suggesting innovative policy options based on payments to farmers operating selected farming systems, as a cost-effective way to reconcile agricultural and environmental policy objectives.

The optical reflection characteristics of asphalt pavement are an important influencing factor in road lighting design, and the macro and micro textures of asphalt pavement significantly affect its reflection characteristics. To investigate the impact of texture parameters on the retroreflection coefficient of asphalt pavement, this study obtained the macroscopic and microscopic texture properties of rutting board specimens and on-site asphalt pavement using a pavement texture tester. The macro- and microtexture parameters, such as macroscopic texture distribution density (D1), microscopic texture distribution density (D2), profile height root-mean-square (Rq), profile slope root-mean-square (Δq), skewness Rsk and kurtosis Rku, were measured, and the corresponding retroreflection coefficient RL was measured using a retro-reflectometer. In the laboratory ex-periments, rutting specimens of AC-13, SMA-13, and OGFC-13 asphalt mixtures were formed. The changes in texture parameters and retroreflection coefficient of different rutting specimens before and after crushing were studied, and a factor influence model between macro- and microtexture parameters and RL was established. And the correlation models of texture index and RL of asphalt pavement are further established. The results showed that in the single factor model, the param-eters can be used to characterize RL with high prediction accuracy, whereas for the on-site meas-urements, the three parameters of Δq, Rsk, and Rku can characterize the RL well. The nonlinear model established on the basis of the B-P neural network algorithm improves its prediction ac-curacy. This research can provide ideas for optimizing the reflection characteristics of asphalt pavement and further provide a decision-making basis for road lighting design.

The motion of Unmanned Surface Vehicles (USVs) is frequently disturbed by the ocean wind, wave and current. A poorly designed controller will lead to failures and even safety problems during actual navigation. In order to obtain satisfied control performance of the motion for the USVs, a Model Predictive Control (MPC) based on improved Nonlinear Disturbance Observer (NDO) is proposed. Firstly, the USV model is approximately linearized and MPC is designed for the multivariable system with constraints. In order to compensate the influence of disturbances, an improved NDO is designed, with which the calculation time for the MPC saved a lot. Finally, comparison experiments are conducted between the MPC with NDO and the MPC with improved NDO, and the results show that they have similar performance to the USVs. However, the proposed method has less parameter to be tuned and it is much more time-saving compared to the MPC with traditional NDO.

This paper presents a new method of process parameters optimization, adequate for 3D printing of PLA (Polylactic Acid) components. The authors developed a new Hybrid Manufacturing Equipment (HME), suitable for producing complex parts made from a biodegradable thermoplastic polymer, for environmental sustainability. Our new HME equipment is producing PLA parts by both additive and subtractive techniques, with the aim of obtaining accurate PLA components with a good surface quality. A design of experiments has been applied for optimization purposes. The following manufacturing parameters were analyzed: rotation of the spindle, cutting depth, feed rate, layer thickness, nozzle speed, and surface roughness. Linear regression models and neural network models were developed to improve and predict the surface roughness of the manufactured parts. A new test part was designed and manufactured from PLA, to validate the new mathematical models, which can now be applied for producing complex parts made from polymer materials.

Shaped surfaces are increasingly used in the field of mould making for casting or injection moulding, where future products include shapes with different curvatures. These are surfaces that form convex curves, concave curves, or a combination thereof. Given these machined surfaces, it is important to know the impact of the finishing strategies on these surfaces. This paper deals with the comparison of finishing milling strategies in the production of shaped surfaces and the analysis of different methods for the evaluation of surface topography, surface roughness and the evaluation of deviations. The material used for the experiments was AlCu4Mg aluminium alloy, and Constant Z, Spiral and Spiral circle strategies were chosen for the finishing strategies. The evaluation of surface topography and surface roughness was carried out at three different sample heights with respect to the tool contact with the machined surface. The results showed changes in the toolpaths due to the variation of the effective diameter of the tool cutter to the machined surface as well as the choice of strategy. To produce specimens with corresponding shapes in terms of topography, the Constant Z strategy was the most suitable, in which uniform toolpaths were obtained over the whole height of the sample.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

Surface waves generated by Extra-Tropical Cyclones (ETCs) can significantly affect shipping, fishing, offshore oil and gas production and other marine activities. This paper presents results of satellite-data-based investigation of wind waves generated by two North Atlantic ETCs. These ETCs were fast-moving systems, inhibiting resonance (synchronism) between the group velocity of the generated waves and the ETC translation velocity. For these cases, the wave generation begins when the front-boundary of the storm appears at a given ocean location point. Since developing waves are slow, they move backward relative to the storm, grow in time, and then leave the ETC stormy area through the rear sector. Multi-satellite observations confirm such a paradigm, and reveal that the storm regions is filled up with young developing wind waves which are most developed in the rear-right sector. As observed, the energy of these waves was growing in time during the ETC life span. It is demonstrated that the extended-fetch concept (inherent for Tropical Cyclones) does not apply for ETC. Instead, by analogy, the concept of extended-duration wave growth concept is more relevant. Satellite observations well confirm the validity of duration-laws for waves generated by ETCs, and demonstrate that extended-fetch regime for observing waves can only asymptotically be achieved, - at time intervals exceeding the lifespan of considered ETCs.

In this study we present a hybrid approach of ACO with fuzzy logic and clustering methods to solve multi-objective path planning problems in case of swarm USVs. This study aims to enhance the performance of ACO algorithm by integrating fuzzy logic in order to cope with the multiple contradicting objectives and generate quality solutions by in parallel identifying the mission areas of each USV to reach the desired targets. The objectives that are taken into account are the minimization of traveled distance and energy consumption, and the maximization of path smoothness. A comparative evaluation is conducted among ACO and fuzzy inference systems, Mamdani (ACO-M) and Takagi–Sugeno–Kang (ACO-TSK). The results showed that depending on the needs of the application, each methodology can contribute respectively. ACO-M generates better paths but ACO-TSK presents higher computation efficiency.

Fringe projection profilometry(FPP) has been extensively applied in various fields for its superior fast speed, high accuracy and high data density. However, measuring some objects with high reflective surfaces or high dynamic range surfaces remains challenging for FPP. Some multiple exposure image fusion methods have been proposed and successfully improved the measurement performance for these kinds of objects. Normally, these methods have a relatively fixed sequence of exposure settings determined by artificial experience or trial and error experiments, which may decrease the efficiency of the entire measurement process and may have less robustness to various environmental lighting conditions and object reflective properties. In this paper, a novel self-adaptive multiple exposure image fusion method is proposed with two main aspects of improvement on adaptively optimizing the initial exposure and the exposure sequence. By introducing the theory of information entropy, combined with the analysis of the characterization of fringe image entropy, an adaptive initial exposure searching method is first proposed. Then, an exposure sequence generation method based on dichotomy is further described. On the base of these two improvements, a novel self-adaptive multiple exposure image fusion method for FPP as well as its detailed procedures are given. Experimental results validate the performance of the proposed self-adaptivity multiple exposure image fusion method by measuring the objects with different surface reflectivity and in different ambient lighting conditions.