The main target of this study was to evaluate the impact of future climate change on the available surface water resources in the Dhidhessa Sub-basin, Abbay Basin, Ethiopia. For the prediction, high-resolution Regional Climate Models (RCMs) from multiple climate models with data from Representative Concentration Pathways (RCPs) prepared by the CCAFS were used. The predictions of future discharge (stream flow) were based on climate scenarios data of baseline period of 1991 to 2020 and for the future with two time windows, 2044 (2030–2059) and 2084 (2070–2099), on a monthly time step after bias correction was conducted to both precipitation and temperature in the future climate under each RCP scenario. After sensitivity analysis, calibration (1994–2011), and validation (2012–2020) of the model for the Dhidhessa Sub-basin with the SUFI-2 program in the SWAT-CUP model, the SWAT model was used to determine water balance and stream flow from the SWAT model system. The SWAT model performed well in predicting stream flow in the Dhidhessa Sub-basins, with a coefficient of determination (R2) ranging from 0.8 to 0.94 and a Nash Sutcliffe value (NSE) ranging from 0.76 to 0.89. The percent decrease in mean annual stream flow from 2044 and 2084 were 10 %, in 2044, and 6.3% in 2084 respectively. The seasonal result under short-term 2044 of stream flow present change significantly decreased in spring, winter, and autumn with 20.2%, 67.4%, and 67.4% respectively. While summer season increased by 43.1%, under short-term 204. In long-term 2084 percent change declined except summer seasons, with 14.7%, 58.1%, and 3.3%, change in spring, winter, and autumn, respectively, and summer, with 51.1% increased and With RCP4.5 (1.64%) and RCP8.5 (2.1%) changed. In the future Dhidhessa stream flow increases and decreases from the baseline era. The decreasing stream flow in 2044 and 2084 will negatively affect agricultural production. This study revealed that any effect on this river resulting in a drop in flow will have a direct impact on ongoing water resource development and socio-economic development of the area.

Tomatoes, one of the most appreciated vegetables consumed, are crops well adapted for cultivation in arid and semi-arid conditions, the success of large yields is guaranteed by covering water consumption through irrigation. Solar Pumps - SP are driven by Photovoltaic Panels - PV (SPAPV), eliminating the dependence on electricity or diesel; they are environmentally friendly because they generate carbon-free electricity and the cost of operation and maintenance is lower. In order to preserve the water administered by drip to the tomato crop grown in solariums, mulching is used. In Husasău de Tinca, in the Crișurilor Plain, cultivation of tomato varieties without mulching (WM) and with mulching with black foil (MBF) were studied. To answer the question "How effective are water conservation measures in terms of energy independence?", two variants of SPAPVs, direct pumping (ADP) and storage tank (AST) were simulated. Considering the conditions in the solariums, tomato crops do not benefit from the contribution of precipitation, therefore it is proposed to determine the water consumption of tomatoes (ETRo), using the temperatures inside the solarium. In 2016, the average temperatures during the vegetation period were observed with an insurance of over 20 %, the irrigation norms were 6945.7 m3 ha-1, for the WM variant and 6594.0 m3 ha-1 for the MBF variant, respectively. Specific Investment (SI) is 214,795 Euro ha-1 in case of ADP and respectively 202,990 Euro ha-1 in case of ATS. The payback period (IPT) is between 2.68 years and 2.53 years for the ADP variant and between 1.63 years and 1.54 years for the ATS variant, respectively. The indications for water use and irrigation water use show that in the MBF variant the water administered by localized irrigation is better utilized than in the WM variant. In the conditions of Crișurilor Plain, the best solution for the distribution of water in solariums, with the help of SPAPVs is the mulching system of tomatoes grown in solariums (MBF) and the arrangement of the drip irrigation system with a water storage tank (ATS).

The research was conducted in the Kırklareli stream, which flows southwest through the city of the same name toward the village of Kavaklı. The aim of the study is to evaluate water analysis results and assess the potential that the European Union drinking water standard for lead can be achieved in the Kırklareli stream by reliance on the low solubility of lead phosphate minerals. The present study used Visual MINTEQ 3.1 for all water chemistry simulations. The European Union drinking water standard for lead, which is 10 μg L⁻¹, is exceeded at least once and as many as three times at seven of the ten sites during the 2018 sampling season. Although the database solubility of hydroxypyromorphite is exceeded in most samples, it appears this may be the result of major ion substitutions in the hydroxypromorphite that forms in the Kırklareli stream which increases the effective solubility of lead in the stream.

A new method is proposed to increase rejection in microfiltration by applying membrane oscillation using a new type of microfiltration membranes with slotted pores. The oscillations applied to the membrane surface result in reducing membrane fouling and increasing separation efficiency. An exact mathematical solution of the flow in the surrounding solution outside the oscillating membrane is developed. The oscillation results in appearance of the lift velocity, which moves oil particles away from the membrane. The latter results in both reducing membrane fouling and increasing oil droplets rejection. This developed model was supported by the experimental results for oil water separation in produced water treatment. It was proven that oil droplet concentration reduced notably in the permeate due to the membrane oscillation and that applied shear rate caused by the membrane oscillation is also reduce pore blockage. New generation of microfiltration membranes with slotted pores was used in the experiments.

The monitoring of surface-water quality followed by water-quality modeling and analysis is essential for generating effective strategies in water-resource management. However, worldwide, particularly in developing countries, water-quality studies are limited due to the lack of a complete and reliable dataset of surface-water-quality variables. In this context, several statistical and machine-learning models were assessed for imputing water-quality data at six monitoring stations located in the Santa Lucía Chico river (Uruguay), a mixed lotic and lentic river system. The challenge of this study is represented by the high percentage of missing data (between 50% and 70%) and the high temporal and spatial variability that characterizes the water-quality variables. The competing algorithms implemented belonged to both univariate and multivariate imputation methods (inverse distance weighting (IDW), Random Forest Regressor (RFR), Ridge (R), Bayesian Ridge (BR), AdaBoost (AB), Hubber Regressor (HR), Support Vector Regressor (SVR), and K-nearest neighbors Regressor (KNNR)). According to the results, more than 76% of the imputation outcomes are considered satisfactory (NSE > 0.45). The imputation performance shows better results at the monitoring stations located inside the reservoir than the ones positioned along the mainstream. IDW was the most chosen model for data imputation.

Human leptospirosis cannot be investigated without studying zoonotic and environmental as-pects of the disease. The objectives of this study are to explore the abundance of Leptospira in dif-ferent climate zones of Sri Lanka and to describe the presence of Leptospira in same water source at different time points. First, water and soil samples were collected from whole-island, secondly, water sampling continued only in dry-zone, finally serial sampling of water from ten open wells was performed at five different time points. Quantitative PCR for water and metagenomic se-quencing for soil were used to detect Leptospira. In first component, 2 out of 12 water sites were positive and both are situated in wet-zone. Very small quantities of Genus Leptospira was detect-ed by metagenomic analysis of soil. Only 5 out of 26 samples were positive in the second compo-nent. Six, five, four, five, six wells were positive respectively in serial measurements of third component. All wells were positive at least one measurement while only one well was positive in all measurements. Closer to tank and higher distance from main road were significant risk fac-tors associated with well positivity. Presence of Leptospira seems not consistent indicating ran-dom abundance of Leptospira in natural environment.

Long-term dewatering of groundwater is a necessary operation for mining safety in open-pit coal mines, while extensive dewatering might cause ecological problems due to dramatical changes of moisture movement in the soil, especially in ecological-fragile areas. This paper presents a quantitative methodology to evaluate the impact of the coal mining operation on moisture movement in the vadose zone by taking the Baorixile open-pit coal mine as an example. A long-term in-situ experiments（from 2004 to 2018), laboratory analysis and numerical modelling were conducted to analyse the mechanisms and relationship among the dropping groundwater level, the vadose-zone moistures, and the ecological responses in the grassland area. The experiment data and modelling results suggest that groundwater level dropping during open-pit mining operation has limited influence on the vadose zone, exhibiting a variation of capillary water zone within a depth of 3 m while the vadose zone and soil water zone were at least 16 m deep. The critical evaporation depth of ground water is 8 m. The long-term influence radius of groundwater dewatering is about 2.72 km during the Baorixile mining operation, and the groundwater level change mainly influences the lower part of the intermediate vadose zone and the capillary water zone below 16 m, with little influence on the moisture contents in the soil water zone where the roots of shallow vegetation grow. The results from this study provide useful insight for sustainable development of coal mining in ecological-fragile areas.

Water deficit caused by drought is a significant threat to crop growth and production. Nitric oxide (NO), a water- and lipid-soluble free radical, plays an important role in cytoprotection. Apart from a few studies supporting the role of NO in drought responses, little is known about this pivotal molecular amendment in the regulation of abiotic stress signaling. In this review, we highlight the knowledge gaps in NO roles under drought stress and the technical challenges underlying NO detection and measurements, and we provide recommendations regarding potential avenues for future investigation. The modulation of NO production to alleviate abiotic stress disturbances in higher plants highlights the potential of genetic manipulation to influence NO metabolism as a tool with which plant fitness can be improved under adverse growth conditions.

Different types of pockmarks, including single pockmarks, circular pockmarks, elongated pockmarks, chain-type pockmarks and compound pockmarks, were identified in coastal areas around Fujian, China. The sediments associated with pockmarks were mainly silty clay to clay, with a small quantity of silt with fine sand. The sulfate content in the pore water in the sedimentary layers associated with pockmarks decreased with depth from the surface, whereas the free methane content increased with depth. The interaction between sulfate and methane is well known, but differences in the sulfate-methane transitional zone (SMTZ) were observed in different areas with different hydrologic characteristics. The sedimentary SMTZ of the offshore Zhe-min mud wedge was shallow, at 50–70 cm below the seafloor. The sedimentary SMTZ was moderately deep (90–115 cm) in the central bay area and deep (180–200 cm) in the sandy area offshore. This variability in SMTZ depth reflects different amounts of free methane gas in the underlying formations, with a shallower SMTZ indicating a higher free methane content. The free methane had δ13C values of -26.47‰ to -8.20‰ and a biogenic-hybrid genetic type. The flux of sedimentary gas from the pockmark surfaces, calculated according to Fick’s formula, was 2.89 to 18.85 l/m2·a. The shape, size and scale of the pockmarks are directly related to the substrate type and the gas production of the underlying strata and thus vary with the sedimentary environment and development stage. Therefore, different types of pockmarks, in various phases of development, are associated with different sedimentary and dynamical conditions. A single circular pockmark forms by strong methane flux. As the intensity of methane flux weakens, the pockmark becomes elongated in the direction of the water flow because of long-term erosion induced by regular hydrodynamic forces. Finally, under weak intensity of methane flux and the influence of complex hydrodynamic conditions, pockmarks merge to form large-scale, compound pockmarks.

Irrigation is a useful crop enhancement procedure up to the point where free surface water appears. Thereafter, water can begin to flow into waterways, leaching nutrients and giving rise to environmental damage, as well as being a waste of a precious resource. The current work addresses the problem of measuring free water on the surface of agricultural soils by a real-time acoustic remote sensing method. Directional acoustic transmitter and receiver arrays are used to define a ‘footprint’ on the ground from which changes in reflectance are sensed. These arrays are mounted on a moving irrigator. Chirp signals are used to provide along-path resolution and to ensure robustness against unwanted acoustic background noise from farm machinery and the irrigator. Field measurements have been conducted above a well-defined ‘quadrat’ with controlled and measured water content, and also with the instrument mounted on an operational irrigator. A structured light camera mounted above the footprint is used to validate surface water fraction. It is found that the areal fraction of free water on the soil surface can be reliably estimated from changes in the amplitude of the reflected sound waves. The mechanism giving rise to the observed acoustic reflectivity changes is discussed and a model is developed which agrees with normalized intensity observations with a coefficient of determination R2 between 0.65 and 0.83. The rms error between model predictions and observations is comparable to the rms variation of the measurements, indicating that there is insignificant error due to the choice of model.

Escherichia coli or E. coli is a member of the fecal coliform group and is a more specific indicator of fecal contamination than other fecal coliform species, its presence indicate possibly presence of harmful bacteria which will cause diseases and it also suggests the extent as well as the nature of the contaminants. E. coli bacteria able to survive in water for 4 – 12 weeks and at present, it appears as an indicator to provide the accurate bacterial contamination of fecal matter in drinking water, because of the availability of simple, affordable, fast, sensitive and exact detection techniques. According to the laboratory experiment based techniques, 24 - 48 hours are required for the bacterial concentration to be reported. So, there is a necessity for continuous monitoring. Techniques for detection of many pathogenic bacterial strains are not yet available, sometimes days to weeks are required to get the results. To overcome the difficulties, expensive and time-consuming techniques are required to detect, count and identify the presence of specific bacterial strain. Public health relies on online monitoring of water quality that depends majorly on examination of fecal indicator bacteria, thus protection of health requires fecal pollution indicator so that it is not required to analyze drinking water to overcome the problems associated with waterborne diseases. This paper will brief the classification, sources, survival of E. coli bacteria and its correlation with basic water quality parameters in water sources.```

The Cape Restionaceae species, an endemic of the Fynbos Biome, is threatened by urbanization, alien plant invasion, agricultural expansion, and groundwater extraction. This is further worsened by the semi-arid conditions and hydrological variability factors, which influences species niche dynamics. Therefore, it is important to assess and monitor the Restionaceae species for preservation of their endemism and richness. This study models the hydrological niche and distribution changes of Restionaceae species at the New Years Peak (NYP) at microclimate level for biodiversity conservation. MaxEnt modelling and GIS analytical approaches were applied at various stages in niche modelling process as follows: (i) microclimatic input raster layers’ generation, (ii) ecological modelling and hydrological niche manipulation, and (iii) spatial distributional change mapping. The hydrological niches of the Restionaceae were effectively examined under the recent climate and compared with RCP2.6 and RCP8.5 future climate scenarios as the microscale environmental inputs. The results showed that most of the studied Restionaceae species positioned themselves along a hydrological gradient. Each species tolerated a range of hydrological conditions, which formed their hydrological niche. Changing climate would cause both positive and negative species range shifts. The study assists in plant species conservation and future climate change impact analysis on endangered plant species.

We have developed IrO_x/M-SnO₂ (M = Nb, Ta, and Sb) anode catalysts, IrO_x nanoparticles uniformly dispersed on M-SnO₂ supports with fused-aggregate structures, which make it possible to evolve oxygen efficiently, even with a reduced amount of noble metal (Ir) in proton exchange membrane water electrolysis. Polarization properties of IrO_x/M-SnO₂ catalysts for the oxygen evolution reaction (OER) were examined at 80 °C in both 0.1 M HClO₄ solution (half cell) and a single cell with a Nafion^® membrane (thickness = 50 μm). While all catalysts exhibited similar OER activities in the half cell, the cell potential (E_cell) of the single cell was found to decrease with the increasing apparent conductivities (σ_{app, catalyst}) of these catalysts: an E_cell of 1.61 V (voltage efficiency of 92%) at 1 A cm^-2 was achieved in a single cell by the use of an IrO_x/Sb-SnO₂ anode (highest σ_{app, catalyst}) with a low Ir-metal loading of 0.11 mg_Ir cm^-2 and Pt supported on graphitized carbon black (Pt/GCB) as the cathode, with 0.35 mg_Pt cm⁻². In addition to the reduction of the ohmic loss in the anode catalyst layer, the increased electronic conductivity contributed to decreasing the OER overpotential due to the effective utilization of the IrO_x nanocatalysts on the M-SnO₂ supports, which is an essential factor in improving the performance with low noble metal loadings.

A waterbody detection technique is an essential part of digital elevation model (DEM) generation to delineate land-water boundaries and set flattened elevations. This paper describes the technical methodology for improving the initial tile-based waterbody data that are created during production of the ASTER GDEM, because without improvement such tile-based waterbody data are not suitable for incorporating into the new ASTER GDEM Version 3. Waterbodies are classified into three categories: sea, lake, and river. For sea-waterbodies, the effect of sea ice is removed to better delineate sea shorelines in high latitude areas, because sea ice prevents accurate delineation of sea shorelines. For lake-waterbodies, the major part of the processing is to set the unique elevation value for each lake using a mosaic image that covers the entire lake area. Rivers present a unique challenge, because their elevations gradually step down from upstream to downstream. Initially, visual inspection is required to separate rivers from lakes. A stepwise elevation assignment, with a step of one meter, is carried out by manual or automated methods, depending on the situation. The ASTER GWBD product consists of a global set of 1º latitude-by-1º longitude tiles containing water body attribute and elevation data files in geographic latitude and longitude coordinates and with one arc second posting. Each tile contains 3601-by-3601 data points. All improved waterbody elevation data are incorporated into the ASTER GDEM to reflect the improved results.

The two-dimensional, laterally-averaged mechanistic eutrophication model CE-QUAL-W2 version 3.72 was used to predict chlorophyll-a concentrations across two different time periods in the Neuse River Estuary, North Carolina. Chlorophyll calibration was performed for two time periods simultaneously by performing by a full-factorial experiment that tested seven algal kinetic growth parameters over three levels for a single algal group. A cluster of up to six computers each running between two and ten instances of the program was used to complete and manage the data for 2187 runs for each time period. A set of six criteria were used to determine which runs performed acceptably, yielding a group of 27 cases that met all of the criteria. Calibration performance of the set of cases outperformed a previously calibrated model using three algal groups that met only four of the six selection criteria. Calibration performed this way allowed for a more rational specification of model calibration performance and provided uncertainty estimates of model predictions, albeit at the cost of a considerable increase in computational requirements that necessitated the use of a computer cluster.

Irrigation scheduling is used by growers to determine the right amount and timing of water application. In most parts of Mozambique, 90% of the total yearly precipitation occurs from November to March. The El Niño Southern Oscillation (ENSO) phenomenon influences the climate in Mozambique and affects the water demand for crop production. The objectives of this work were to quantify the effects of ENSO phenomenon on tomato crop water requirements, and to create the AgroClimate irrigation tool (http://mz.agroclimate.org/) to assist farmers in improving irrigation management. This study was based on daily grid-based climate information from 1983 to 2016 from the Climate Forecast System Reanalysis. Daily crop evapotranspiration was calculated by Hargreaves equation and crop coefficients. This tool is available online and considers different planting dates, ENSO phases, and crop growing season lengths. Irrigation needs varied from less than 250 mm per growing cycle during winter to 550 mm during spring. Both El Niño and La Niña influenced the irrigation scheduling, especially from November to March. El Niño periods were related with increased water demand due to drier and warmer conditions while the opposite was observed for La Niña. The ENSO information might be used to understand climate variability and improve tomato irrigation scheduling in Mozambique.

Infrared spectroscopy is an effective method for the determination of compositions and concentrations of liquids, with advantages of fast response, no-sampling, flexible in use and is able for on-line monitoring. However, for trace substances in drinking water, such as nitrates and heavy metals, infrared spectroscopy is not sensitive enough for the quantitative and qualitative measurement. In this study, we improved the sensitivity of infrared spectroscopy for nitrite determination by developing an ion-exchange-enhanced diffuse reflectance spectroscopy, which consist of an accessory based on ion-exchange resin for enrichment and a FTIR spectrometer for measurement. Using this method, the limit of detection for nitrate is 1.7 mg/L, which is enough for drinking water sensing. We also verified the quantitative measurement ability of the method. Furthermore, the limit of detection and quantitative measuring range could be adjusted by changing the mass of resin and adsorption time. This study demonstrated the method can be used to detect trace nitrites in drinking water, can be applied in the field, and is sensitive, rapid, and inexpensive with a wide dynamic range.

Water resources, especially safe, potable water, are limited for many Haitians. In areas where shallow groundwater is available, many household water needs such as laundry, bathing, and cooking are supplied by hand-dug wells. In order to better understand the water quality and prevalence of these household wells, 35 hand-dug wells were surveyed and sampled near the Hôpital Albert Schweitzer (HAS) in Deschapelles, Haiti. Water samples were collected and tested for fecal coliform and E. coli using the IDEXX Colilert-18 method. Of the samples collected, 89 percent were determined unsafe to use as a drinking water source based on the World Health Organization standard of 1.0 colony-forming unit (cfu) Escherichia Coli (E. coli) per 100 mL. 66 percent of the wells exceeded recreational/body contact standards for the state of Michigan (130 cfu/100 mL). Some of these wells were deemed suitable for conversion to a new well type called In-Situ Filtration (ISF) wells. ISF wells are installed with an internal sand filter pack, PVC casing, pump, and cap which seals the well from surface contamination and provides additional water treatment as water is pumped. Previous ISF installations have reduced E. coli to safe drinking water levels within 90 days.

The development of a novel and simple inhibition biosensor array for detection of water pollutants based on immobilized bacteria is the main goal of this work. A series of electrochemical measurements (i.e. cyclic voltammograms) were carried out on screen-printed gold electrodes with three types of bacteria, namely Escherichia coli, Shewanella oneidensis, and Methylococcus capsulatus, immobilized via poly L-lysine. For comparison purposes, similar measurements were carried out on bacteria samples in solutions,; also optical measurements (fluorescence microscopy, optical density, and flow cytometry) were performed on the same bacteria in both liquid and immobilized forms. The study of the effect of heavy metal ions (lead), pesticides (atrazine) and petrochemicals (hexane) on DC electrochemical characteristics of immobilized bacteria revealed a possibility of pattern recognition of the above inhibition agents in aquatic environment.

Revitalization of open water bodies into recreational areas are becoming widely popular in many parts of Sri Lanka. Understanding community perception and expectation on recreational development have important policy and cost-effectiveness implications. This paper explores the public perspectives on development, conservation and value of the open water recreational development at Diyatha Uyana and surrounding area. Contingent Valuation Method has been applied to estimate peoples’ Willingness To Pay for recreational spaces in the selected area. A total of 300 residents from different socioeconomic backgrounds were selected randomly for the study. Enjoying peace and relaxation, taking children to play and breath clean air were mentioned as most important aspects of open water body areas. More frequent visits occur to enjoy peace and relaxation, breath clean air and enjoy the natural landscape. Almost all the participants were agreed upon conserving open water body areas in urban settings. Willingness to pay was significantly associated with income and occupation status. It yielded a monthly average payment of Rs.446.93 per household for another five years’ time. The limited budget was the main reason for not willing to pay. This paper is significant as there is no contingent valuation method study has been carried on water body development in Sri Lanka.

This review deals with the adaptive mechanisms that plants can implement to cope with the challenge of salt stress. Plants tolerant to NaCl implement a series of adaptations to acclimate to salinity, including morphological, physiological and biochemical changes. These changes include increases in the root/canopy ratio and in the chlorophyll content in addition to changes in the leaf anatomy that ultimately lead to preventing leaf ion toxicity, thus maintaining the water status in order to limit water loss and protect the photosynthesis process. Furthermore, we deal with the effect of salt stress on photosynthesis and chlorophyll fluorescence and some of the mechanisms thought to protect the photosynthetic machinery, including the xanthophyll cycle, photorespiration pathway and water-water cycle. Finally, we also provide an updated discussion on salt-induced oxidative stress at the subcellular level and its effect on the antioxidant machinery in both salt-tolerant and salt-sensitive plants. The aim is to extend our understanding of how salinity may affect the physiological characteristics of plants.

Today, the style of light construction materials used in building is one of the most important factors in reducing building's dead load and better performance of the structures in the earthquake. One of the ways to reduce the structure weight is to use lightweight blocks instead of using traditional materials. The main purpose of this research is to compare density, compressive strength and water absorption volume of non-load-bearing lightweight blocks made of natural and artificial lightweight aggregates. Scoria lightweight aggregates of Sanandaj, Ghorveh mine, pumice in Tabriz, Bostanabad mine, and Leca in Leca enterprise have been used to make the samples. Given the importance of the materials used, grading of coarse-grained materials has been conducted based on the standard of 7657 and grading of fine materials have been conducted based on the standard of 302.The experiments' results show that Scoria blocks due to hard texture, and high mechanical resistance of their lightweight aggregates, have had higher compressive strength, and density and lower water absorption volume compared to pumice and Lika lightweight aggregate blocks. Pumice blocks despite having desirable compressive strength and lower density compared to the two other blocks have higher water absorption volume, and do not meet the standard conditions. This same factor causes it faces with less interest. Among these Lika blocks with density of 1151.94 (kg per cubic meter) below 2000 kilograms per cubic meter of Iran density standard of 7782 (28-day compressive strength of 2.57 MPa), higher than 2.5 MPa of Iran compressive strength standard of 7782 (and water absorption volume of 282.92 kg per cubic meter) below 288 kilograms per cubic meter of Iran water absorption volume standard of 7782 (as a non-load-bearing lightweight block) have been diagnosed desirable.

The increasing rate of adoption of innovative technological achievements along with the penetration of the Next Generation Internet (NGI) technologies and Artificial Intelligence (AI) in the water sector, are leading to a shift to a Water-Smart Society. New challenges have emerged in terms of data interoperability, sharing, and trustworthiness due to the rapidly increasing volume of heterogeneous data generated by multiple technologies. Hence, there is a need for efficient harmonisation and smart modeling of the data to foster advanced AI analytical processes which will lead to efficient water data management. The main objective of this work is to propose two Smart Data Models focusing on the modeling of the Satellite Imaginary data and the Flood Risk Assessment processes. The utilisation of those models reinforces the fusion and homogenisation of diverse information and data facilitating the adoption of AI technologies for flood mapping and monitoring. Furthermore, a holistic framework has been developed and evaluated via qualitative and quantitative performance indicators revealing the efficacy of the proposed models concerning the usage of the models in real cases. The framework is based on the well-known and compatible technologies on NGSI-LD standards which are customised and applicable easily to support the water data management processes effectively.

All empirical water column correction methods have consistently been reported to require existing depth sounding data for the purpose of calibrating a simple depth retrieval model; they yield poor results over very bright or very dark bottoms. In contrast, we set out to (i) use only the relative radiance data in the image along with published data, and several new assumptions, (ii) in order to specify and operate the simplified radiative transfer equation (RTE), (iii) for the purpose of retrieving both the satellite derived bathymetry (SDB) and the water column corrected spectral reflectance over shallow seabeds. Sea truth regressions show that SDB depths retrieved by the method only need tide correction. Therefore it shall be demonstrated that, under such new assumptions, there is no need (i) for formal atmospheric correction, (ii) nor for conversion of relative radiance into calibrated reflectance , (iii) nor for existing depth sounding data, to specify the simplified RTE and produce both SDB and spectral water column corrected radiance ready for bottom typing. Moreover, the use of the panchromatic band for that purpose is introduced. Altogether, we named this process the Self-Calibrated Supervised Spectral Shallow-sea Modeler (4SM). This approach requires a trained practitioner, though, to produce its results within hours of downloading the raw image. The ideal raw image should be a “near-nadir” view, exhibit homogeneous atmosphere and water column, include some coverage of optically deep waters and bare land, and lend itself to quality removal of haze, atmospheric adjacency effect, and sun/sky glint.

Dietary restrictions or reductions such as fasting for weight loss, are often difficult to adhere to in the long term due to increased appetite and food cravings. Recently, gastrointestinal delivery of bitter hops extract has been shown to be effective at reducing appetite in men. Our aim was to determine the effect of bitter hops on appetite and cravings in women, using a day-long, water-only fast. Thirty adult women were recruited and required to fast for 24 h from 1800 h to 1800 h on three occasions and given an ad libitum meal to break each fast. Treatments of either a placebo or one of two doses (high dose; HD: 250 mg or low dose; LD: 125 mg) of a bitter hops-based appetite suppressant (Amarasate®) were given twice per day at 16 and 20 h into the fast. Treatment with both the HD and LD treatment groups exhibited a significant (p < 0.05) reduction in appetite and cravings for food. Two participants reported loose stools and one reported heart-burn while on the HD treatment, and one participant reported loose stools while on the LD treatment. These data suggest that appetite suppressant co-therapy may be useful in reducing hunger during fasting in women and shows that gastrointestinal delivery of bitter compounds may also be an effective method of reducing cravings for food.

The boreal Hemisphere has been experiencing increasing extreme hot and dry conditions over the past few decades, consistent with anthropogenic climate change expectations. The continental extension of the phenomenon calls for tools and techniques capable of monitoring the global to regional scales. In this context, the satellite is the only system that can satisfy the need for global coverage. The main objective we have addressed in the present paper is the capability of infrared satellite observations helping to monitor the vegetation stress due to increasing drought and heatwaves in summer. We have designed and implemented a new water deficit index (wdi) that exploits satellite observations in the infrared to retrieve humidity, air temperature, and surface temperature simultaneously. These three parameters are combined to provide the water deficit index. The index has been developed based on the Infrared Atmospheric Sounder Interferometer or IASI, which covers the infrared spectral range 645 to 2760 cm-1 with a sampling of 0.25 cm-1. The index has been used to study the 2017 heatwave, which hit Continental Europe from May to October. In particular, we have examined Southern Italy, where Mediterranean forests suffer from climate change. We have computed the index's time series and show that it can be used to indicate the atmospheric background conditions associated with meteorological drought. We have also found a good agreement with soil moisture, which suggests that the persistence of anomalously high water deficit index was an essential driver of the rapid development and evolution of the exceptionally severe 2017 droughts.

Clausius’ virial theorem set a basis for relating kinetic energy in a body of independent material particles to its potential energy, pointing to their complementary role with respect to the second law of maximum entropy. In action mechanics, expressing the entropy of ideal gases as a capacity factor for sensible heat or enthalpy plus the configurational work to sustain the relative translational, rotational and vibrational action yields algorithms for estimating chemical reaction rates and positions of equilibrium. All properties of state including entropy, work potential as Helmholtz and Gibbs energies and activated transition state reaction rates can be estimated, using easily accessible molecular properties, such as atomic weights, bond lengths, moments of inertia and vibrational frequencies. Understanding how Clausius’ virial theorem balances the internal kinetic energy with field potential energy justifies partitioning between thermal and statistical properties of entropy, yielding a more complete view of the evolutionary nature of the second law of thermodynamics. The ease of performing these operations is illustrated by three important chemical gas phase reactions, the reversible dissociation of the hydrogen molecules, lysis of water to hydrogen and oxygen and the reversible formation of ammonia from nitrogen and hydrogen. Employing the ergal also introduced by Clausius to define the reversible internal work to overcome molecular interactions plus the configurational internal work of negative Gibbs energy as a function of volume or pressure may provide a practical guide for managing risk in industrial processes and climate change at the global scale.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

Considering Cu(tda) chelate is a receptor for adenine and related 6-aminopurines, now we report the synthesis, molecular and crystal structures, thermal stability, spectral properties and DFT calculations on the [Cu(tda)(9heade)(H2O)]•2H2O (1). N7 is found to be the preferred donor atom of 9heade, that can favor the cooperation of a Cu-N7(9heade) bond and an (9heade)N6-H•••O(tda) interligand interaction. But unprecedentedly, the Cu(tda)-9heade molecular recognition in 1 is essentially featured the Cu-N1(9heade), without any N6-H•••O(carboxyl tda) interligand interaction. Nevertheless, being N1 the most basic donor for N9-substituted adenines, this Cu-N1 bond is now assisted by an O2-water mediated interaction (N6-H•••O2 and O2•••Cu weak contact). Also in the crystal packing, the O-H(ol) of 9heade interacts with its own adenine moiety by an O3-water mediated interaction (O(ol)-H•••O3 plus O3-H36•••π(adenine moiety). In turn these water-mediated interactions seems to be responsible to serious alterations on the physical properties of crystalline or grounded samples. Density functional theory calculations were used to evaluate the interactions energetically. Moreover, the quantum theory of atoms-in-molecules (QTAIM) in combination with the noncovalent interaction plot (NCIPlot) were used to analyze the interactions and rationalize the existence and relative importance of hydrogen bonding, chalcogen bonding and π-stacking interactions.

The water resources carrying capacity (WRCC) system comprises multiple complex and nonlinear interactions related to society, economy, water resources and the water environment. A full understanding of its internal mechanism is conducive to the further improvement of the regional WRCC. This article focuses on the temporal and spatial variability of WRCC to explore a method of dynamic successive assessment. Firstly, the Pressure-State-Response (PSR)framework is used to develop a systematic and causal indicator system. Then, The Variable Fuzzy Pattern Recognition (VFPR) model and an analytic hierarchy process-entropy (AHP-E) model are combined to successively and dynamically assess WRCC. The proposed method is applied to the dynamic successive assessment of WRCC in Hebei Province, and it is obtained that the poor water resources carrying capacity in Hebei Province is mainly due to the basic attribute of the decision of the water resources shortage, but Hebei Province actively adopts a variety of measures to save water and pressurize mining, which makes the province's water resources carrying capacity have a tendency to become better gradually. At the same time, the system dynamics model (SD) of water resources carrying capacity based on the analysis of the model structure was established. Moreover, three scenarios were designed, including existing continuation, high-efficiency water-saving, cross-regional water transfer and coordinated development, each scenario divided into high and low-speed economic development and population growth schemes, then total 6 schemes between 2023 and 2030 were simulated and predicted respectively. The results indicate that if the current development model is adopted, the water resource carrying capacity will continue to maintain low levels. It was concluded that the high-speed development of economy and population, the efficient water conservation and inter-basin transfer scenario (scenario 2 with high-speed) is the best choice for sustainable development of water resources and social economy in Hebei.

Tsunami is a type of infrequent geohazards with devastating consequences, which makes accurate computer simulations of tsunami waves particularly desirable for hazard assessment and mitigation purposes. The evolution of a typical tsunami involves the generation, propagation and inundation phases. In this survey, we briefly describe the most common types of tsunamigenic sources and give a detailed review of some most widely used mathematical models for describing tsunami propagation. We emphasize the approximations adopted in each mathematical model and point out their most important advantages and disadvantages. Tsunami propagation modeling is computationally demanding, involving a wide span of spatial and temporal scales. While some of the approximate models are sufficiently accurate for describing wave behaviors at certain scales, they might not be applicable at other scales. Effective and efficient tsunami propagation simulations will likely depend upon the proper coupling of different models for different scales.

Plug and abandonment (P&amp;A) operations demand valuable time and resources with operational procedures and materials to establish the well barrier element. This study proposes the use of a water-based fluid as a liquid well barrier element for temporary abandonment, based on esti-mates of its lifespan and survival probability on downhole conditions acquired through acceler-ated life tests. For that, the water-based formulation was tested and exposed to 95, 110, 140 and 150°C, for time intervals ranging from 1 to 10 days. After temperature exposure, the fluid prop-erties were verified and failure was detected by accounting for any deterioration in rheological parameters and/or a substantial increase in filtrate volume. Statistical analysis of failure data was performed in R software using Weibull Model, and fluid average lifespan and survival probability were estimated for P&amp;A temperatures. The results obtained demonstrates that the degradation of the fluid only was observed for 140 and 150°C and is mostly related to the CMC deterioration. The reliability metrics shows that until 80°C the fluid is a promising alternative for temporary abandonment, with no need of monitoring. For higher downhole temperatures, theses metrics should be considered to define the maximum time of operation and requirements for monitoring management in the operation design.

Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.

Water recycling and reuse are corner stones in the water management that may be compromised by the presence of pollutants. Among them, pharmaceuticals can overcome the standard water treatments and require sophisticated approaches to remove them. Sorption is an economically affordable alternative limited by the need of sorbents that exhibit sorption coefficient (Kd) higher than 500 L/kg to be useful in wastewater treatment plants (WWTPs). We report that th cross-linking of dextrin (Dx) with divinyl sulfone (DVS) in presence of 1 mmol or 5 mmol of ibuprofen (IBU) yields the insoluble polymers pDx1 and pDx5 with improved affinity for IBU, Kd higher than 600 L/kg for ciprofloxacin (CIP) and ofloxacin and an outstanding Kd higher than 4000 L/kg for erythromycin (ERY), when assayed against a cocktail of 6 drugs. The characterization of the polymers by XRPD, TGA and SEM reveals that both pDx1 and pDx5 share similar features, with an ERY Kd of 13 x 103 for pDx1 and 6.4 x 103 for pDx5. The facts that new affinities and improvements in Kd can be achieved by cross-linking Dx in presence of other molecules that promote a pre-organization, broaden the applications of DVS cross-linked polysaccharide as sustainable and eco-friendly sorbents.

The geographical location of Yunnan province is at the upstream area of water vapor transportation from the Bay of Bengal and the South China Sea to inland China. Understanding the spatiotemporal variations of water vapor over this region holds significant importance. We utilized the GNSS data collected from 12 stations situated in Yunnan, which are part of Crustal Movement Observation Network of China, to retrieve hourly precipitable water vapor (PWV) from 2011 to 2022. The retrieved PWV at Station KMIN were evaluated by the nearby radiosonde data, and the result shows that the mean bias and RMS of the differences between the two datasets are 0.08 and 1.78 mm respectively. Average PWV values at these stations are in the range of 11.77 to 33.53 mm, which decrease from the southwest to the north of Yunnan and are negatively correlated with the station heights and latitudes. Differences between average PWV in wet season and dry season range from 12 to 27 mm. These differences tend to increase as the average PWV increases. The yearly rates of PWV variations, averaging 0.18 mm/year, are all positive for the stations, indicating a year-by-year increase in water vapor. Amplitudes of the PWV annual cycles are 9.75-20.94 mm. The spatial variation of these amplitudes is similar to that of average PWV over the region. Generally, monthly average PWV values increase from January to July and decrease from July to December, and the growth rate is less than the decline rate. Average diurnal PWV variations show unimodal PWV distributions over the course of the day at the stations except Station YNRL, where bimodal PWV distribution was observed.

Eutrophication is a major environmental issue with many negative consequences, such as hypoxia and harmful cyanotoxins production. Monitoring coastal eutrophication is a crucial, especially for island countries like the Republic of Cyprus, which are economically dependent on the touristic sector. Additionally, the open-sea aquaculture industry in Cyprus has been exhibiting an increase in the last decades and environmental monitoring to identify possible signs of eutrophication is mandatory according to the legislation. Therefore, in this modelling study, two different types of Artificial Neural Networks (ANNs) are developed based on in situ-data collected from stations located in the coastal waters of Cyprus. Theses ANNs aim to model the eutrophication phenomenon based on two different data-driven modelling procedures. Firstly, the self-organizing map (SOM) ANN examines several water quality parameters (specifically water temperature, salinity, nitrogen species, ortho-phosphates, dissolved oxygen and electrical conductivity) interactions with the Chlorophyll-a parameter. The SOM model enables us to visualize the monitored parameters relationships and to comprehend complex biological mechanisms related to Chlorophyll-a production. A second feed-forward ANN model is also developed for predicting the Chlorophyll-a levels. Based on this ANN model, several scenarios associated to the eutrophication-related water quality parameters can be extracted. The combination of these two ANNs models is considered a holistic modelling approximation for the identification of eutrophication scenarios, since it enables not only the prediction of the Chlorophyll-a parameter levels, but also the “capturing” of hidden biological mechanisms associated with algal production.

RCH is known rapidly enhance cold tolerance of insects. Trehalose has been demonstrated to be one of the cryoprotectant in L. oryzophilus, an important invasive pest of rice in China. Trehalose synthesis mainly occurs through the TPS/TPP pathway in insects. In this study, LoTPS gene was cloned and characterized for the first time. Its expression and trehalose content changes elicited by RCH were investigated. Our results revealed that RCH not only increased the survival rate of adults but also upregulated the gene expression level of LoTPS and increased trehalose content under low temperature. We hypothesized upregulated LoTPS promoted trehalose synthesis and accumulation to protect adults from low-temperature damage. To further verify the function of LoTPS gene, we employed RNAi technology. Our findings showed that RCH efficiency disappeared and failed to increase the survival rate when the adults were fed dsRNA of LoTPS. Additionally, inhibiting LoTPS gene expression resulted in no significant difference in trehalose content between RCH and non-RCH treatments. Furthermore, the expression patterns of TRET and TRE were also affected. Collectively, these results indicate the critical role of LoTPS in L. oryzophilus cold resistance after RCH induction. LoTPS can enhance the survival ability by regulating trehalose metabolism. These findings contribute to further understanding of the role of TPS in insect cold resistance and invasiveness of L. oryzophilus. Moreover, RNAi of the LoTPS opens up possibilities for novel control strategies against L. oryzophilus in the future.

We report the use of four-layer graphene (4LG) as a highly reliable transparent conductive electrode (TCE) for polymer-dispersed liquid crystal (PDLC)-based smart window devices. The adhesion between 4LG and the substrate was successfully improved through a water-induced interface-cleaning (WIIC) process. We compared the performance of a device with a WIIC-processed 4LG electrode with that of devices with a conventional Indium tin oxide (ITO) electrode and a 4LG electrode without a WIIC. With the application of the WIIC process, the PDLC smart window with a 4LG electrode exhibited reduced turn-on voltage and haze compared to 4LG without the WIIC process and characteristics comparable to those of the ITO electrode. Based on our observations, we conclude that 4LG with WIIC is a promising TCE for flexible smart windows.

Femtosecond laser-induced fluorescence (FLIF) and femtosecond laser-induced optical breakdown spectroscopy (FIBS) are important tools for remote diagnostics of atmospheric aerosols using LiDAR techniques. They are based on light emission excitation in disperse medium via the multiphoton nonlinear processes in aerosol particles induced by high-power optical pulses. To date, the main challenge restraining the large-scale application of the FLIF and FIBS in atmospheric studies is the lack of valued theory of the stimulated light emission in liquid microparticles with sufficiently broad range of sizes. In this paper, we fill this gap and present the theoretical model of dye water droplets emission under high-intense laser exposure that adequately simulates the processes of multiphoton excited fluorescence and optical breakdown plasma emission in microparticles and gives quantitative estimates of the angular and power characteristics of the nonlinear emission. The model is based on the numerical solution to the inhomogeneous Helmholtz equations for the stimulating (primary) and nonlinear (secondary) waves provided by the random nature of molecule emission in particles. We show that droplet fluorescence stimulated by the multiphoton absorption generally becomes more intensive with increasing particle size. Moreover, far-field plasma emission from liquid particles demonstrates larger angular diversity when changing droplet radius in comparison with the multiphoton excited fluorescence, which is mainly due to the excitation of the internal optical field resonances in spherical particles.

Steam Generator Level Control System (SGLCS) is one of the key instrumentations and control subsystems to ensure the safe operation of nuclear power plants. It is highly recommended to perform reliability analysis for SGLCS for making better maintenance strategy. SGLCS is a digital control system with complex redundant configuration and failure\self-diagnosis\repair action, traditional fault tree is not applicable due to its static property, Markov model is not a good choice too because of heavy burden of creating state transition graph for even medium-size system. Boolean Logic Driven Markov Process (BDMP) can describe complex failure-repair state transition via ‘trigger link’ and three kinds of leaf nodes, as well as keep compact and easy-read struct like fault tree. So BDMP is adopted to analysis reliability of SGLCS. Graphical BDMP modeling environment KB3 and Monte Carlo simulator YAMS is used for BDMP modeling and quantitative analysis respectively, and unavailability of SGLCS is obtained. The contribution of three parts of SGLCS to the unavailability of the system is also evaluated, and it is found that the water supply flow control part contributes the most to the failure of SGLCS.

The Mediterranean is one of the regions of the world where human-induced climate warming is expected to have large impacts on water and environmental resources. To predict shifts in the current climate system, more regional climate records, including seasonal-to-century scale variability spanning longer than the instrumental periods, are needed. To help fill this gap, we provide a reconstruction of autumn precipitation variations for the Central Pyrenees range since 1500 Common Era (CE) using the varved sediments of Lake Montcortès. To assess the suitability of the calcite sublayer width of the sediments of this lake as a proxy for precipitation anomalies, we performed an analysis and smoothing of the temporal structure of the width series, calibration of the new series with the available instrumental climate records, calculation of a transfer function and testing and comparison of the reconstructed series against available empirical data.The prediction model was statistically robust and showed that the climatic signal was captured in the calcite sublayers. The reconstruction provides the first estimations of regional autumn precipitation shifts in the Central Pyrenees at annual resolution, since 1500 CE. Pronounced interdecadal shifts in precipitation were noticeable; no increasing nor decreasing linear trends or periods of extreme precipitation events were identified. The reconstructed precipitation anomalies suggest a decrease in rainfall during the coldest phase within the coldest period of the Little Ice Age and also during the 20^th century, probably associated to current Global Warming. Correlations between autumn precipitation and the North Atlantic Oscillation, Western Mediterranean Oscillation and Southern Oscillation indices were weak to moderate. A potential relationship with the Atlantic Multidecadal Oscillation pattern is suggested. The reconstructed autumn precipitation trends are coherent with other palaeohydrological reconstructions in similar Mediterranean settings, and consistent at a regional level.

The water quality of the river is becoming deteriorated due to human interference. It is essential to understand the relationship between human activities and land-use types to assess the water quality of a region. GIS has the latest tool for analyzing the spatial correlation. Land use land cover and change detection is the best illustration to show the human interactions on land features. The study assessed water quality index of upper Ganga River near Haridwar, Uttarakhand and spatially correlated them with changing land use to reach a logical conclusion. At the upper course of Ganga along 78 Km long from Kaudiyala to Bhogpur, water samples were collected from five stations. For water quality index the physicochemical parameters like pH, EC, DO, TDS, CaCO3-, CaCO3, Cl¯, Ca++, Mg++, Na+, K+, F-, Fe2+ were considered. The result of the spatial analysis was evaluated through error estimation and spatial correlation. The root mean square error between spatial land use and water quality index of selected sampling sites was estimated as 0.1443. The spatial correlation between land-use change and site-wise differences in water quality index has also shown a high positive correlation with R² = 0.8455. The degree of positive correlation and root mean square error has strongly indicated that the water quality of the river at the upper course of Ganga is highly impacted through human activities.

Population growth and increasing global demand for freshwater have raised a serious challenge for the depleting sources of freshwater in the 21st century. Desalination technologies can be a reliable technique for providing freshwater. Capacitive deionization is one of the innovative desalination methods that has received increasing interest. Flow-electrode capacitive deionization (FCDI) (a new architecture of capacitive deionization) is one of the efficient, cost-effective, and environmentally-friendly desalination methods for freshwater production. In this experimental research, the performance of an FCDI system was investigated and the influence of important parameters such as flow rate of flow-electrodes, electrolyte salt concentration of flow-electrodes, and initial feed water concentration will be assessed on the efficiency of desalination operation. In this study, the flow-electrodes operated in short-circuited closed-cycle operation (SCC) mode, and also the feed water operated similarly to the flow-electrodes in closed-cycle. Moreover, in all the experiments, the salt adsorption capacity (SAC) and salt removal efficiency (SRE) was calculated. Herein, by optimizing the above mentioned parameters, the salt removal efficiency of 83% and a SAC value of 29.12 mg/g dry carbon were achieved in 5 hours.

Bioethanol has many environmental and practical benefits as a transportation fuel. It is one of the best alternatives to replace fossil fuels due to its liquid nature which is similar to petrol and diesel fuels traditionally used in transportation. In addition, bioethanol production technology has the capacity for negative carbon emissions which is vital for solving the current global warming dilemma. However, conventional bioethanol production takes place based on an inland site and relies on freshwater and edible crops (or land suitable for edible crop production) for production, which has led to the food vs fuel debate. Establishing a coastal marine biorefinery (CMB) system for bioethanol production that is based on coastal sites and relies on marine resources (seawater, marine biomass and marine yeast) could be the ultimate solution. In this paper, we aim to evaluate the environmental impact of using seawater for bioethanol production at coastal locations as a step towards the evaluation of a CMB system. Hence, a life cycle assessment for bioethanol production was conducted using the proposed scenario named Coastal-Seawater and compared to the conventional scenario, named Inland-Freshwater (IF). The impact of each scenario in relation to climate change, water depletion, land use and fossil depletion was studied for comparison. The coastal-seawater scenario demonstrated an improvement upon the conventional scenario in all the selected impact categories. In particular, the use of seawater in the process had a significant effect on water depletion showing an impact reduction of 31.2%. Furthermore, reductions are demonstrated in natural land transformation, climate change and fossil depletion of 5.5%, 3.5% and 4.2% respectively. This indicates the positive impact of using seawater and coastal locations for bioethanol production and encourages research to investigate the CMB system.

The Urban Eco-Sustainable Index for Upscaling Water Security at Catchment Level in Langat River, Malaysia has developed by using the Modified Watershed Sustainability Index or MicroWSI (MWSI), which was based on the Participation, Design and Management Components. The study has successfully applied spatial and social dimensions on ecohydrology of the selected Langat River reach for stormwater management, natural ecosystems health and quality of life. The planning and public participation aspects of the study have evaluated the surrounding neighborhood area of Langat. The conceptual design of rehabilitation works implementation related to Urban Stormwater Management Manual for Malaysia (MSMA) Stormwater Management Ecohydrology (SME) within the study area has been developed with four components of MSMA-SME to be implemented in the study area i.e Bioretention System, Porous Pavement System, Constructed Wetland and Slope Protection Works. These components were proposed to be applied in the development of Langat Riverfront Community Park (LRCP) which has taken into account the components of Design, Management and Participation of Community and Stakeholders in Langat River Basin, Malaysia. This study analyzed the MWSI for the Upscaling of MSMA Ecohydrology at Catchment Level of Langat River and has found the medium level of sustainability for the level of participation, proposed design, and management. Thus, there is a need to increase the level of readiness in the community and stakeholder participation in the Langat River towards sustainability of river conservation and rehabilitation programmes in this basin.

Highly-resolved data on water balance components (like runoff or storage) are crucial to improve water management, e.g., in drought or flood situations. Because regional observations of these components cannot be acquired adequately, applying water balance models is a feasible solution. We developed an innovative approach using the physically-based lumped-parameter water balance model BROOK90 (R version) integrated into a sensor network platform to derive daily water budget components for catchments in the Free State of Saxony. The model is not calibrated but rather uses available information on soil, land use and precipitation only. We applied the hydro response units (HRUs) approach for 6175 small and medium-sized catchments. For the evaluation, model output was cross-evaluated in ten selected head catchments in a low mountain range in Saxony. The mean values of Kling-Gupta efficiency (KGE) for the period 2005-2019 to these catchments are 0.63 and 0.75 for daily and monthly discharge simulations, respectively. The simulated evapotranspiration and soil wetness are in good agreement with the SMAP_L4_GPH product in April 2015-2018. The study can be enhanced by using different data platforms as well as available information on study sites.

Liquefaction risk assessment is critical for the safety and economics of structures. As the soil strata of Ramsar area in north Iran is mostly composed of poorly graded clean sand and the ground water table is found at shallow depths, it is highly susceptible to liquefaction. In this study, a series of isotropic and anisotropic consolidated undrained triaxial tests are performed on reconstituted specimens of Ramsar sand to identify the liquefaction potential of the area. The specimens are consolidated isotropically to simulate the level ground condition, and anisotropically to simulate the soil condition on a slope and/ or under a structure. The various states of soil behavior are studied by preparing specimens at different initial relative densities and applying different levels of effective stress. The critical state soil mechanics approach for identifying the liquefaction susceptibility is adopted and the observed phenomena are further explained in relation to the micro-mechanical behavior. As only four among the 27 conducted tests did not exhibit liquefactive behavior, Ramsar sand can be qualified as strongly susceptible to liquefaction. Furthermore, it is observed that the pore pressure ratio is a good indication of the liquefaction susceptibility

In this article, we report the generation of alternating current by application of constant and ramping DC voltages across oil-water interfaces. The work reported here can be broadly divided into two parts depending on the shapes of oil-water interfaces i.e. flattened and curved. In the first part, an alternating current of ~100 nA (amplitude)was generated by applying a constant DC voltage of -3V& above across a free standing and flattened oil-water interface.In another part, an alternating current of ~150 nA (amplitude) was generated by applying a ramping up DC voltage starting from -5V to 5V, then again ramping back down to -5V for the free standing and curved interface. The suggested qualitative mechanism that engenders such a phenomenon includes the oil-water interface acting like a membrane. This membrane oscillates due to the electrophoretic movement of ions present in aqueous phase by application of a DC voltage across the interface.This electrophoretic movement of ions across oil-water interfaces causes the Faraday instabilities leading to oscillations of the said interface.This method could also be used to study the stress levels in the interfacial films between two immiscible liquids. It explores more-than-Moore’s paradigm by finding a substitute to a conventional alternator/inverter that generates alternating current upon applying DC voltage input. This work would be of substantial interest to researchers exploring alternatives to conventional AC generators that can be used in liquid environments and in the design of novel integrated circuits that could be used for unconventional computing applications.

Easy to use satellite-based water quality visualizations are needed for monitoring and understanding coastal and inland waters, but to date, no publicly accessible real-time global visualization system was in place. Here we introduce the Ulyssys Water Quality Viewer (UWQV), a Sentinel Hub EO Browser Custom script designed for qualitative views of aquatic chlorophyll and suspended sediment concentrations. The viewer avoids unmixing of the chlorophyll and suspended sediment spectral signal by visualizing these parameters together, with high concentrations of suspended sediment obscuring chlorophyll if present. Cloud masking uses the Hollstein and Braaten algorithms (existing EO Browser custom script code), additionally water surfaces are masked using the Normalized Differential Water Index. Chlorophyll is estimated using reflectance line height-based indicators such as fluorescence line height and maximum chlorophyll index. Suspended sediment is visualized based on single-band reflectances at 620 or 700 nm. Data sources are Sentinel-2 and Sentinel-3 images, allowing either 20 m spatial resolution or up to daily imaging. This visualization system is easy to operate and interpret, and combined with the data service capacity of the Sentinel Hub, it is expected that UWQV will contribute to monitoring of remote water bodies and to our overall understanding of physical limnology and aquatic ecology.

In this study, effluent water was produced through Submerged Membrane Bio-Reactor (SMBR) process, which is a simple system and decomposes organic matter contained in wastewater with biological treatment process and performs solid-liquid separation, Especially, ozone oxidation treatment process is applied to effluent water containing fluorescent whitening agent, which is a trace pollutant which is not removed by biological treatment, and influences the quality of reused water. The concentration of COD in the SMBR was 449.3 mg/ℓ-COD, and the concentration of permeate water was 100.3 mg/ℓ-COD. The removal efficiency was about 70.1%. The amount of ozone re- quired for the removal of the fluorescent whitening agent in the permeated water in SMBR was 6.67 g-O3/min, and the amount of ozone required to remove COD relative to the permeate water was calculated to remove 0.997 mg-COD for 1 mg of O3.

The exposure of people to opportunistic premise plumbing pathogens (OPPPs) such as Legionella, Mycobacterium and Pseudomonas in aerosolised water has been linked to opportunistic infections. Water mist systems (WMS) that are used to cool public places by flash evaporation of tiny water aerosols are gaining prominence in hot climatic regions of Australia. Their potential to be colonised by OPPPs has not been adequately studied. The public health impact of OPPPs is significant, as Legionella caused 63% of waterborne disease case hospitalisations in the United States associated with drinking water systems during 2013–2014, and the incidence of Mycobacterium avium over the same period was 647 cases per 100,000. As WMS are part of premise plumbing, they have structural characteristics that can promote biofilm formation, as well as the presence of free-living amoebae (FLA), low residual disinfection levels, elevated water temperatures and oligotrophic conditions, all of which can promote OPPP inhabitancy. This review highlights the potential public health risks of using WMS as a cooling intervention in public places and advocates for their regulation in places of public assembly and entertainment.

Original and improved version of the Hardy Cross iterative method with related modifications are today widely used for calculation of fluid flow through conduits in loops-like distribution networks of pipes with known node fluid consumptions. Fluid in these networks is usually natural gas for distribution in the municipalities, water in waterworks or hot water in district heating system, air in the case of ventilation systems in buildings or mines, etc. Since, the resistances in these networks depend of flow, problem is not linear like in electrical circuits, and iterative procedure must be used. In both version of the Hardy Cross method, in original and in the improved one, initial results of calculation in iteration procedure is not flow, but rather the correction of flow. Unfortunately, these corrections should be added to or subtracted from a flow calculated in previous iteration according to complicate algebraic rules. After the here presented node-loop method, final results in each of the iterations is flow directly rather than flow correction. In that way complex algebraic scheme for sign of flow correction is avoided, while the final results still remain unchanged. Numbers of required iterations for the same results are comparable with the improved Hardy Cross method.

Increasing salt intake has substantial negative impacts on health and well-being. This review article focusses on the effect of salinity intrusion (SI) on the water quality and community health of coastal Bangladesh and to find out the effectiveness of interventions for reducing the negative effects of salinity. Saline water is a noteworthy reason for hypertension or high blood pressure in the coastal areas. Health status of women especially the pregnant women are vulnerable because of drinking water sodium (DWS) prompting to pre-eclampsia, high blood pressure and hypertension as well as infant mortality. Several interventions such as rainwater harvesting and Pond sand filter (PSF) system as well as managed aquifer recharge (MAR) usage and the integration of mixed sources were reviewed on the content of drinking water sodium (DWS). Although rainwater has the positive impact of low or no sodium intake on human health, it still possesses negative impacts from not having vital minerals. Despite what might be expected, in MAR a steady increment in sodium concentration through the span of the dry season was observed. It is, subsequently, important to increase awareness about drinking water sodium (DWS) intake by providing and adopting correct technological interventions.

Object. Flooding in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous. In an average year floods on the rivers of Volyn region take place from one to three times which extend beyond the limits of the floodplain. The floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Methodology. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. Based on the statistical data of the Volyn Regional Center for Hydrometeorology during the 7 year period 2011-2017 about water levels of the river Styr. We conducted mathematical modeling of fluctuations of water levels within the territory of Lutsk, based on creating a partial Fourier series for discrete values of middle-ten-day water levels values. The post hydrological measurements of Styr river water levels in the territory of Lutsk located on the Shevchenko Street comply with an altitude 172.87 meters. Based on the data of short-term flood forecasting in February and March, and relief data from the Department of Architecture and Urban Development of Volyn State Administration, we conducted visualization of the results using geographic information system QGIS. Results. The results of mathematical processing were the basis for geoinformation simulation of flooded areas using remote sensing data that are publicly available. Use of statistical and geospatial data in this article has great potential for further application in modeling the processes of natural and technogenic origin. Scientific novelty. The mathematical model of short-term forecasting of water levels during the flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed. Practical significance. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The spring flood in February-March 2018, with the maximum water level 5.33 m, corresponds to an absolute mark of 178.20 m, which is forecasted in this article.

This paper proposes an Integrated Fire Management (IFM) framework that can be used to support communities and resource managers in finding effective and efficient approaches to prevent damaging fires, as well as maintain desirable fire regimes in Kenya. Designing and implementing an IFM approach in Kenya calls for a systematic understanding of the various uses of fire and the underlying perceptions and traditional ecological knowledge of the local people. The here proposed IFM framework allows an evaluation of the risks posed by fires, while balancing them with their beneficial ecological and economic effects, and thus developing effective fire management approaches. A case study of the proposed IFM framework was conducted in Gathiuru Forest that is part of the larger Mt. Kenya Forest Ecosystem. Focus group discussions were held with key resource persons, primary and secondary data on socio-economic activities were studied, fire and weather records were analyzed and the current fire management plans were consulted. Questionnaires were used to assess how the IFM is implemented in the Gathiuru Forest Station. The results show that the proposed IFM framework is scalable and can be applied in places with fire-dependent ecosystems as well as in places with fire-sensitive ecosystems in Kenya. The effectiveness is dependent on the active participation, formulation and implementation of the IFM activities by the main stakeholder groups (Kenya Forest Service (KFS), Kenya Wildlife Service (KWS), and the Community Forest Associations (CFA)). The proposed IFM framework helps in implementing cost-effective approaches to prevent damaging fires and maintain desirable fire regimes in Kenya.

Floods in Ukraine is a common natural phenomenon that repeats periodically and in some cases it becomes disastrous signs. In an average year in the rivers of Volyn passes from one to three floods with going beyond the limits of the floodplain. Floodplain of Styr river is located in the historical center of Lutsk city, that`s why issues of research and forecasting of floods are very important for a given city. Using modern technologies of geodesy and remote sensing allows to quickly determine and predict the floodplain area of settlements. The research results of water level changes on the Styr River and flood zones within the limits of Lutsk is proposed. The mathematical model of short-term forecasting of water level in flood period on the river Styr with implementation of geoinformation modeling of flooded areas using remote sensing data is proposed.

The greater Wellington region, New Zealand, is highly vulnerable to large earthquakes because it is cut by active faults. Bulk water supply pipelines cross the Wellington Fault at several different locations, and there is considerable concern about severe disruption of the provision of reticulated water supplies to households and businesses in the aftermath of a large earthquake. A number of policy initiatives have been launched encouraging householders to install rainwater tanks to increase post-disaster resilience. However, little attention has been paid to potential health hazards associated with consumption of these supplies. To assess health hazards for householders in emergency situations, six 200-litre emergency water tanks were installed at properties across the Wellington region, with five tanks being allowed to fill with roof-collected rainwater and one tank being filled with municipal tapwater as a control. Such tanks are predominantly set aside for water storage, and once filled, feature limited drawdown and recharge. Sampling from these tanks was carried out fortnightly for one year, and samples analysed for E. coli, pH, conductivity, a range of major and trace elements, and organic compounds, enabling an assessment of the evolution of water chemistry in water storage tanks over time. Key findings were that the overall rate of E.coli detections in the rain-fed tanks was 17.7%, which is low in relation to other studies. We propose that low incidences of E.coli may be due to biocidal effects of high zinc concentrations in tanks, originating from unpainted galvanised steel roof cladding. Lead concentrations were high compared to other studies, with 69% of rain-fed tank samples exceeding the World Health Organisation’s health-based guideline of 0.01 mg/L. Further work is required to determine risks of short-term consumption of this water in emergency situations.

This study examines the DCMA concerning the future risk of the water security status. We considered three risk factors: population growth, economic growth, and natural water supply demand differences. In the risk analysis part, we consulted with experts from several sectors including academia, Non-Governmental Organization (NGOs), and industry, to predict that the probability of future water stresses in high, medium, and low scenarios are 0.73, 0.24, and 0.03, respectively. In the decision analysis part, we adopted two Multiple Criteria Decision Analysis (MCDA) approaches that include Multiple Attribute Value Theory (MAVT) and Analytic Hierarchy Process (AHP) methods to evaluate the best alternative decision to alleviate future water stresses in the DCMA. The sensitivity analysis demonstrates the best option closely connects to the weighting scheme of the criteria considered in the framework. This study provides a valuable risk and decision analysis framework to analyze the water security status associated with the future water supply and demand gap decrease caused by three risk factors: population growth, climate change, and natural water supply.

The poor solvent crystallization of carbapenem CS-023 has been performed at 25 °C. The following results have been obtained: 1) A solvate crystal Form A (5/2 Ethanol·1/2 H2O) is recovered from 80 v/v% ethanol solution, 2) Form A transforms to Form H (4H2O) by the solid-phase transition through the solvate-free polymorph, Form A-2, and Form A also transformed to Form C (1Ethanol·3H2O) by the solvent-mediated transformation. In the present study, we found that Form C also transforms to Form H by the solid-phase transition through the solvate-free polymorph, Form C-2. The three polymorphs, Form A, H, and C, were composed of the helical-chain structures, respectively. However, there was an incomprehensible affair in the solid phase transition among the three polymorphs. Namely, Form A comprised a left-handed helix.On the other hand, Form C and Form H’s helix chains were in a left- and right-handed helix complex. The solid-phase transition of Form A into Form H suggested the switch of helicity in the solid. We attempted to explain the helicity change in the solid phase transition. As a result, it was suggested that the over-absorption of water of Form A-2 at high humidity plays a vital role in the helicity change.

Two pilot scale desalination system employing carbon modified nano-sized, zero valent metals (n-ZVM) were maufactured and tested to determine (1) the degree to which high salt water (20 to 130 mS) could be desalinated and (2) if this degree of desalination could be maintained throughout an extended treatment period. Two pilot systems were tested (referred to as Generation 1 and Generation 2) consisting of parallel lines of 4 individual reactors in series, a settling tank and an activated carbon cell at the end of each reactor line. The system capacity was 300 gal in Generation 1 and 600 gal in Generation 2 total with a total hydraulic residence time of 6 hours per reactor line (one hour per cell/tank). A slurry of n-ZVM was introduced in the first reactor on each line to yield approximately 5 to 45 grams of nano-metal per 100 L of influent salt water. The n-ZVM slurry was made from mixing tea extract with metal salts (eg ferrous sulfate, ferric chloride) to produce the carbon modified metal slurry. Initial runs focused on dosing required to achieve maximum salt removal at each of three influent salt contents, 28 mS, 44 mS and 123 mS. Once dosing was set, continuous runs (14 days, 23 days and 9 days) were carried out to (1) examine the ability of the pilot to maintain the removal efficiency over an extended period, (2) to determine the weaknesses inherent in the pilot systems, and (3) to begin to develop CAPEX and OPEX estimates for the pilot and pre-design full scale mobile desalination unit (MDU) system. Results demonstrated that maximum removal occurred with 10 g/100L of salt for the 30 mS salt solution,16 g/100 L of salt for the 40 mS influent water and 40 g/100 L for the 130 mS influent. Salt removal (expressed as Na and Cl removed) approached 78% for the 30 mS influent and 41 mS influent respectively while removal for the highest salt influent (130 mS) approached 81 %. Addition of greater amounts of carbon modified slurry than those described resulted in a pH less than 6 which inhibits continued salt removal and would require addition of calcium or magnesium oxides/hydroxides or bicarbonate solutions at the influent side to achieve greater salt removal and of course greater cost per gallon. Continuous operation over the extended time-period showed no significant decrease in salt removal with typical day to day variation of no more than 10% suggesting that this approach to desalination could rapidly provide usable water from saline aquifers, seawater or even produced water. Treatment of saline waters at 30 mS or less yields effluent water in the range necessary for irrigation use of many crops while treatment of seawater or produced water levels of salt (40 mS or higher) yields effluent in the range of 8 to 10 mS a range ideal for RO influent that would prevent the production of large volumes of brine. Pilot testing continues with seawater extracted from Puget Sound, Seattle WA and higher levels of salt to better represent produced water.

In the seasonally frozen regions, during the grouting of prestressed bridge ducts in low-temperature environments, incompletely cured grout materials undergo volumetric changes due to the freeze-thaw cycling, resulting in structural cracks along the prestressing ducts of the bridge, thereby diminishing the bridge's operational lifespan. To investigate the frost heaving characteristics of grout materials under freeze-thaw cycles and propose potential enhancements, this study was devised to conduct frost heaving stress tests on grout materials. Through this research, we gained insights into how various additives affect the frost heaving stress characteristics of grout materials under freeze-thaw cycles. Incorporating analyses of free water content, setting time, compressive strength, as well as macroscopic examinations such as XRD and SEM, this study delves into the mechanisms for enhancing frost heaving characteristics of grout materials. Furthermore, it proposes a research approach that utilizes multiple admixtures to improve the frost heaving properties of grout materials. Through frost heaving stress tests and other macroscopic experiments, the study investigates the influence of these combined admixtures on frost heaving stress in grout materials and elucidates the underlying improvement mechanisms. The results indicate that reducing the water-cement ratio, incorporating calcium formate, sulfoaluminate cement, air-entraining agents, and carbamide all have a positive impact on mitigating frost heaving stress in grout materials. However, the improvement mechanisms differ, and employing a single measure alone is insufficient to effectively reduce frost heaving stress while meeting performance criteria such as compressive strength, setting time, and flowability. Free water content emerges as a crucial indicator determining the magnitude of frost heaving stress in grout materials, with 11.5% of free water content representing the critical threshold for frost heaving in grout materials. Utilizing composite admixtures can simultaneously decrease free water content, lower the freezing point of free water, and alleviate frost heaving deformation, resulting in more efficient reduction of frost heaving stress. When the admixture content reaches 9.9%, frost heaving stress is eliminated, and the comprehensive performance parameters including compressive strength, setting time, and flowability meet the specified requirements.

Physical processes play important roles in controlling eutrophication and oligotrophication. In stratified lakes, internal waves can cause vertical transport of heat and nutrients without breaking the stratification, through boundary mixing events. Such is the case in tropical Valle de Bravo (VB) lake, where strong diurnal winds drive internal waves, boundary mixing and hypolimnetic warming during stratification periods. We monitored VB during 18 years (2001-2018) when important water-level fluctuations (WLF) occurred, affecting mixing and nutrient flux. Mean hypolimnetic temperature increase (0.06–1.04°C month-1) occurred in all the stratifications monitored. We analyzed temperature distributions and modeled the hypolimnion heat budget to assess vertical mixing between layers (26,618–140,526 m-3h-1), vertical diffusivity coefficient KZ (6.2x10-7–3.3x10-6 m2s-1) and vertical nutrient entrainment to epilimnion on monthly scale. Stability also varied as a function of WLF. Nutrient flux to the epilimnion ranged 0.36–5.99 mg m-2d-1 for soluble reactive phosphorus (SRP) and 5.8–97.1 mg m-2d-1 for dissolved inorganic nitrogen (DIN). During low water-level years, vertical nutrient fluxes increase and can account for up to &gt;40% of the total external nutrients load to the lake. Vertical mixing changes related to WLF affect nutrient recycling, their flux to sediments, ecosystemic metabolic balance and planktonic composition of VB.

Forecasting streamflow accurately is essential to achieve an efficient integrated water resources management strategy and provide consistent support to water decision-makers. We present a simple, low-cost and robust approach for forecasting monthly and yearly streamflow during the hydrological year in course, applicable to headwater catchments. It combines the use of regression analysis techniques, the two-parameter Gamma continuous cumulative probability distribution function and the Monte Carlo method. It is based on a probabilistic comparison of the progression of the current hydrological year with the historic observed series. The methodology has been successfully applied to two headwater reservoirs within the Guadalquivir River Basin in southern Spain. The root-mean-square error and correlation coefficient were used to measure the accuracy of the model and the results showed good levels of reliability. The outputs are the probabilistic monthly and yearly streamflow and 80% confidence interval. Further reductions in prediction errors may be achieved from increasing the number of observed years. These risk-based predictions are of great value, especially, before the intensive irrigation campaign starts (usually in April), when Water Authorities are to take responsible management decisions about the best allocation of the available water volume between the different water users and environmental needs.

Many studies have demonstrated hydrogen's therapeutic and preventive effects on various diseases. Its selective antioxidant properties against hydroxyl radicals, which are responsible for the indirect effects of ionizing radiation, may make it worthy of attention as a new radio-protector. We recently developed new hydrogen water that is more stable and has higher antioxidant activity by using ultra-fine bubbles. In this study, female C57BL/6J mice given ad libitum access to ultra-fine bubble hydrogen water (UBHW) were subjected to whole-body irradiation (WBI) with X-rays, and the radio-protective effect of UBHW was evaluated. Sub-lethal WBI resulted in a 30-day survival rate of 100% in UBHW-fed mice, compared with 37% in control mice. In the case of lethal WBI, while the control mice died out in about 3 weeks, the 30-day survival rate improved to 40% by UBHW due to the high scavenging activity of hydroxy radicals. Twenty-six serum proteins involved in inflammatory and immune responses were significantly identified in UBHW-fed mice by proteomics, and UBHW may enhance and regulate these functions, resulting in reduced damage in mice exposed to WBI. We conclude that UBHW has good potential in radio-protection, with evidence that warrants further research efforts in this field.

Climate change is significantly reshaping global and regional climates, with profound impacts on local microclimates and agricultural productivity. This study investigates the effects of climate change on regional microclimates and examines how these shifts influence agricultural output, focusing on case studies from vulnerable regions. Utilizing secondary climate data from international agencies, this research applies statistical techniques, including time series analysis, correlation analysis, and extreme value theory, to assess changes in temperature, precipitation, and other environmental factors. The study employs spatial analysis to explore the geographic variability in these effects, and regression models to quantify the relationship between climatic changes and crop yields. Preliminary results indicate a marked shift in microclimate patterns, with significant consequences for farming practices, particularly in regions reliant on climate-sensitive crops. The findings underscore the need for adaptive strategies in agricultural sectors to mitigate the risks posed by climate change. This research provides valuable insights for policymakers and farmers, emphasizing the importance of localized climate data in developing sustainable agricultural frameworks.

Throughout the world, salinity is a major environmental issue that limits agricultural productivity, particularly in arid and semi-arid regions. In addition, climate change is the most important reason for the salinization of agricultural soils in the world, so it is now essential to find solutions to increase salinity tolerance in plants. This study investigated the potential of arbuscular mycorrhizal fungi (AMF) inoculation to enhance the growth and yield performances of flax under different salinity levels by conducting a pot experiment. The experiment was laid out in a two-factor completely randomized design including AMF inoculation (AMF+: with and AMF-: without inoculation) and irrigation water salinity (0, 50, 100, and 150 mM NaCl). According to the results, it is evident that salt stress caused negative physiological effects, including limited growth, reduced photosynthesis, and decreased nitrogen (N) and phosphorus (P) content in shoots and roots of flax plants. Moreover, mycorrhizal association improved the salt tolerance of the plants by increasing chlorophyll content, enhancing N and P shoot and root contents, and consequently yield parameters, such as seed, and stem fiber yield, particularly at moderate salt concentrations (50 and 100 mM NaCl). As a result of using AMF, flax plants grown under salt stress exhibited tolerance, suggesting that AMF could be applied in saline environments to maintain ecological stability.

The study on the sustainable utilization capacity of water resources is of great significance for the realization of sustainable water resources management and development in the water-scarce regions of Northwest China. It provides insights into the potential for sustainable utilization of these resources. To evaluate the sustainable utilization capacity of the Huangshui Basin, a comprehensive evaluation index system was constructed based on three aspects: climate factors, water resources systems, and socio-economic factors. The evaluation was conducted using two methods: the fuzzy comprehensive evaluation model and the ELECTRE III evaluation method. The results indicate that the Huangshui Basin's water resources, as a whole, exhibit a medium sustainable utilization capacity. Climatic factors and socio-economic characteristics are the main factors affecting the sustainable utilization of water resources in the Huangshui Basin. Based on the results, measures such as strengthening the introduction of external water resources, enhancing water resources management, and implementing comprehensive remediation efforts in the basin can improve the level of sustainable use of water resources. The research results can provide a reference for decision-making regarding the evaluation of sustainable utilization capacity of water resources in water-scarce areas and the optimization of water resources management in the Huangshui Basin.

Seasonal precipitation variance significantly alters soil water content, potentially inducing water stress and affecting plant transpiration in semiarid deserts. This study explored the effects of environmental variables and hydraulic conductance on whole-tree transpiration (ET) in Mongolian pines (Pinus sylvestris var. mongolica) across different forest stages in the semiarid deserts of northern China. We measured ET using sap flow in mature (MMP), half-mature (HMP), and young (YMP) Mongolian pine plantations. Measurements included soil-leaf water potential difference (ΔΨ), atmospheric conditions, and soil moisture contents on sunny days, both in dry and wet periods. Seasonally variable rainfall distinctly affected soil moisture, correlating ET with photosynthetically active radiation (PAR) and vapor pressure deficit (VPD). Notable nocturnal sap flow occurred during the growing season. During the dry periods, both stomatal and hydraulic conductance influenced ET, whereas during the wet periods, stomatal conductance primarily regulated it. Discrepancies between predicted and measured ET were noticed: compared to the predicted ET, measured ET was lower during dry periods while higher during wet periods. Hydraulic conductance (KT) increased with tree height (H) and ΔΨ, although tall trees exhibited lower KT rates, suggesting that hydraulic compensation had occurred. This compensation, observed between 11:00 and 13:00, aligned with increased hydraulic resistance during dry periods. Decreasing hydraulic conductance intensified leaf water stress in dry periods, especially during the time when PAR and VPD were heightened, potentially increasing stomatal sensitivity to drought, promoting water conservation and plant survival. A linear relationship between predawn and midday leaf water potentials was noticed, indicating extreme anisohydric behavior across forest stages during both dry and wet periods. Although both stomatal and hydraulic conductance influenced ET during the dry period, MMP and YMP were more susceptible to drought conditions. Understanding these dynamics could help evaluate semiarid desert ecological functions for water conservation amidst uneven seasonal precipitation in Northern China.

Heavy metals represent a class of chemical elements that includes metalloids, bases and transition metals, lanthanides and actinides. They are distinguished for their toxicity in small concentrations and for their negative effects on the environment and human health. They are present in various samples, mainly in water, industrial waste and food. The determination of heavy metals is carried out mainly by analytical methods, using spectroscopy, spectrometry and electroanalysis, while studies are being carried out for the development of new and faster methodologies and techniques for their analysis, with particular emphasis on voltammetry. This review deals with the determination of heavy metals mainly in environmental samples (water) using voltammetry. In particular, the methods of their determination are evaluated in terms of sensitivity, selectivity and applicability.

The recent green manufacturing demands have boosted the development of new biodegradable lubricants to replace petroleum-based lubricants. In this regard, water-based lubricants have been at the forefront of recent research for a wide range of industrial applications, including metalworking fluids (MWFs). In this work, we present an experimental investigation on the performance of novel green MWFs based on aqueous nopal mucilage solutions. For this, fully biodegradable solutions with different mucilage concentrations were evaluated in terms of rheological, tribological, thermal stability and turning (minimum quantity lubrication) performance, and compared to a commercial semisynthetic oil-based MWF (Cimstar 60). Mucilage solutions exhibited viscoelastic shear-thinning behavior, which was enhanced along with mucilage concentration. The solution with the highest mucilage content studied resulted in the lowest wear, friction and temperature in comparison to the other solutions and neat water in extreme pressure four-ball tests, and a similar level of lubricity as compared to the commercial MWF in cutting tests. This performance is associated to the enhanced viscosity and elasticity of the solution, as well as to the contents of lipids with fatty acids in the mucilage. Overall, the present results reveal the relevance of the viscoelastic behavior of the lubricant, elasticity in particular, in lubrication processes, and points to nopal mucilage as an effective green additive to produce innocuous MWFs.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

A unique method for synthesizing a surface modifier for metallic hydrogen permeable mem-branes based on non-classic bimetallic pentagonally structured Pd-Pt nanoparticles has been de-veloped. It was found that nanoparticles had unique hollow structure. This significantly reduces the cost of their production due to economical use of metal. According to the results of electro-chemical studies, synthesized bimetallic Pd-Pt/Pd-Ag modifier showed excellent catalytic activi-ty (up to 60.72 mA cm–2), long-term stability and resistance to COads poisoning in alkaline oxida-tion reaction of methanol. The membrane with pentagonally structured Pd-Pt/Pd-Ag modifier showed the highest hydrogen permeation flux density up to 27.3 mmol s–1 m–2. Obtained hy-drogen flux density were 2 times higher than that for membranes with classic Pdblack/Pd-Ag modifier and an order of magnitude higher than that for unmodified membrane. Since the rate of transcrystalline hydrogen transfer through a membrane increased, while the speed of transfer through defects remained unchanged, a one and a half times rise in selectivity of the developed Pd-Pt/Pd-Ag membranes was recorded and it amounted to 3514. Achieved results are due to both the synergistic effect of the combination of Pd and Pt metals in the modifier composition and the large number of available catalytically active centers, which are present as a result of non-classic morphology with high-index facets. The specific faceting, defect structure and unusual properties provide great opportunities for the application of nanoparticles in the areas of membrane reac-tors, electrocatalysis, petrochemical and hydrogen industries.

The global rising demand for exploiting limited shared groundwater resources, coupled with significant water deficit, especially in arid and semi-arid regions, has led to escalating conflicts among stakeholders. As such, using Bankruptcy Theory methods can be an appropriate response to the reallocation of resources. This study introduces a novel approach to weighted Bankruptcy, where the relative importance of stakeholders is determined by their contributions to sustainable development, and the impact of their claims on the shared groundwater resources is considered. The framework is implemented in a two-level bankruptcy process including the plains and their beneficiaries (agriculture, drinking and industry). The proposed two-level weighted bankruptcy process applies to the Neyshabour-Ataiyeh-Sabzevar plains in Iran. The process is implemented for two scenarios including the Baseline scenario related to the present status of demands and the Future scenario associated with the estimated demands for the year 2041. To compare the weighted proposed method with the other weighted methods such as Proportional (WPRO), Constrained Equal Awards (WCEA), Pinile (WPIN), Talmud (WTAL), Constrained Equal Losses (WCEL), Modified Constrained Equal Losses (MWCEL), two categories including the deficit-based and resource-based approaches are considered. According to the stability analysis using the Bankruptcy Allocation Stability Index (BASI) method, among the deficit-based methods, the novel approach is chosen as the preferred method for the beneficiaries’ reallocation like the Sabzevar’s beneficiaries. Accordingly, it allocates 86.95%, 10.86% and 2.17% of the shared resource to the agricultural, drinking, and industrial demands, respectively. Among the resource-based methods, the WPIN method is selected for reallocation between the stakeholders and their beneficiaries in each level and scenario of reallocation. The novel approach offers a promising solution to the water resource reallocation problem, ensuring a more equitable and sustainable management of shared groundwater resources.

The analysis of water inflow is a key issue in the construction of subsea tunnels. However, present research on the water inflow of subsea tunnels is predominantly focused on single-bore tunnels. Given the current practices in engineering, it is common to see a parallel configuration of three bores. In such cases, the proximity of tunnels to one another might result in alterations to the water inflow due to the interplay of seepage fields. This paper begins by conducting a numerical simulation to assess the water inflow characteristics of a three-bore parallel subsea tunnel. The study then investigates the impact of many factors, including the permeability coefficient of the surrounding rock, the depth of the seawater, the depth of the tunnel, the spacing between tunnels, and the relative size of the tunnels, on the water inflow phenomenon. Furthermore, based on the principles of the analytic hierarchy process and fuzzy mathematics, a comprehensive assessment framework is developed to evaluate the water inflow of three-bore parallel subsea tunnels. Ultimately, this grade of water inflow is used in practical engineering. The results show that there is mutual influence between the three parallel tunnels, and the predicted water inflow will be too large if the single tunnel model is adopted. The interaction between tunnels should be considered in the water inflow grade evaluation system of the three-hole parallel submarine tunnel. Engineering cases show that using a single-hole tunnel model without considering the interaction between tunnels will lead to higher water inflow grades. The research results of this paper can provide guidance for the waterproofing and drainage design of three parallel subsea tunnels and the stability analysis of surrounding rocks.

Women are at higher risk of cognitive impairment and Alzheimer’s disease (AD) after menopause when the estrous cycle becomes irregular and begins to taper off. Numerous studies have shown that estrogen deficiency, especially estradiol (E2), has been shown to play a key role in this phenomenon. Recently, a novel polymeric drug, hyaluronic acid-17β-Estradiol conjugate (HA-E2), has been developed which has the ability to cross the blood-brain barrier (BBB), facilitate a longer E2 release profile and lower risk of estrogen supplement related side effects. In this study, we used an ovariohysterectomy (OHE) rat model of postmenopausal cognitive deficits and explore whether HA-E2 treatment can improve the cholinergic septo-hippocampal innervation system, synaptic transmission in the hippocampal pyramidal neuron and cognitive impairment. Our results show that OHE rats after HA-E2 administration have increased expression of choline acetyltransferase (ChAT) in the medial septal nucleus (MS nucleus) and the hippocampus, increased spine density in hippocampal pyramidal neurons, and improved spatial learning and memory. Therefore, HA-E2 has great potential as a new novel class of drugs for estrogen-deficiency-induced cognitive impairment and AD.

Data-driven models (DDMs) are extensively used in environmental modeling but face challenges due to limited training data and potential results not adhering to physical laws. To address this challenge, this study developed a process-guided deep learning (PGDL) model, integrating a long short-term memory (LSTM) neural network and a process-based model (PBM), CE-QUAL-W2 (W2), to predict water temperature in a stratified reservoir. The PGDL included an energy constraint term from W2's thermal energy equilibrium into the cost function of the LSTM, besides the mean square error term. In PGDL, parameters were optimized by penalizing deviations from the energy law, ensuring adherence to physical constraints. Compared to LSTM, PGDL demonstrated enhanced satisfaction with the energy balance and superior performance in water temperature prediction. Even with less field data for training, PGDL outperformed both LSTM and calibrated W2 after pre-training with data generated using the uncalibrated W2. Therefore, integration of DDM with a PBM ensured physical consistency in water temperature prediction for complex stratified reservoirs with limited data. Moreover, pre-training the PGDL with PBM proved highly effective in mitigating bias and variance due to insufficient field measurement data.

Sudden water pollution accident is a tough environmental challenge to solve due to its uncertainty, unpredictability and destructiveness. Therein, the dangerous goods transportation accidents on the cross-tributary bridges are increasing worldwide with the acceleration of industrialization and urbanization, posing threats to the water ecological environment and human health. To prevent and control the risk, this study evaluated the risk of sudden water pollution accidents associated with dangerous goods transportation on the cross-tributary bridges by using the expert judgment fuzzy language method and Bayesian network model. Baiyangdian lake as the largest freshwater shallow lake in North China was chosen as a study case. Different accident scenarios were simulated to put forward risk prevention and control measures. The results showed that the primary risk factors were divided into five categories: personnel factors, vehicle factors, tank factors, weather factors, and road environment factors. The probability of dangerous goods transportation accidents was a possible event (P=0.115), with a high risk level. Furthermore, the Baiyangdian lake would suffer from serious environmental pollution and water quality degradation without prevention and control measures by simulating the oil leakage accident. Therefore, emergency prevention and control measures are expected to be formulated and implemented before and after the occurrence of the sudden water pollution accidents. This study provides useful insights into risk prevention and control strategies for sudden water pollution accidents, and the framework can be made applicable to other rivers facing similar risk challenges worldwide.

The development of knowledge graphs for water resources as a tool for studying sustainable regional development is a relevant task, as the increasing deterioration of water bodies affects the ecology, economy of the country, as well as the health of the population living near water bodies. Solving this problem requires the development of water resource monitoring methods based on semantic data analysis is required to detect and track sources of pollution and provide recommendations to support decision-making. This research proposes a method of semantic analysis for modeling knowledge graphs and constructing rules that enable the integration of data from heterogeneous sources, semantic compatibility, support for reasoning and inference, facilitate queries and search, and represent knowledge in the field of water resource monitoring. As a result, an ontology based on the SWRL language is created, which enables the expression of complex relationships and derivation of new knowledge, SSN for interaction between the ontology and sensor data, and Time Ontology, which models and analyzes information related to temporal aspects.After populating the ontology and establishing logical connections, SPARQL queries are implemented to retrieve new knowledge about water resources.

Reservoir in the Central Structural Zone of the Xihu Sag is the Huagang Formation, dominated by natural gas reservoirs, and the reservoir in the Western Slope Zone is the Pinghu Formation, dominated by light oil and wet gas. In this paper, the Gas Drive Water Displacement- Magnetic Resonance Imaging (GWD-MRI) experiments are used to simulate the charging characteristics of the sandstone migration layer. The centrifugal- Magnetic Resonance (Cen-NMR) experiments simulate the short-term fast trap charging process, and the Semi-Permeable Baffle (SPB) charging experiment simulates the slow trap accumulation process. Studies have shown that there is a start-up pressure for the migration layer charging, and the start-up pressure of the core with a permeability of 0.3mD is about 0.6MPa. Experimental simulations have confirmed that there is a front zone with changed water saturation, with a width of about 1-1.5cm. The migration layer charging mainly has two actions, drive effect and carry effect. The drive effect reduces the water saturation to 70%-80%, and the carry effect can still reduce the water saturation by 5%-10%. The water saturation of rapid charging is mainly affected by the petro-physical. The porosity is high, the water saturation is low. The water saturation decreased significantly with the increase of centrifugal force when the centrifugal force is smaller. If the centrifugal force is greater than 0.8 MPa, the water saturation decreases slowly. The water saturation of the trap slowly charging is basically maintained at 40%-50%, which matches the water saturation of the airtight coring from 40%-55%, the petro-physical do not affect the final water saturation.

The threat posed by climate change, the progressive erosion of natural resources, the polluting effects related to private motorization, energy waste, excessive consumption of agricultural and natural soils and their progressive waterproofing and reduction in vegetation cover, with the subsequent environmental degradation, have highlighted the need for a sustainable management of natural resources, in terms of an equitable and ethical development, to build inclusive communities able to adapt to the negative effects of emergency phenomena, through new capacities of economic, cultural and social resilience. This contribution presents the results of the activities conducted in the RivEr/Generation_LAB, a project organized by three CIVIS members (Sapienza University of Rome, Universitè libre de Bruxelles, Universidad Autonoma de Madrid) as a part of the CIVIS Project "RivEr/Generation_LAB. Linking resilience with inclusiveness in the urban built environment of Rome, Brussels, and Madrid", financed into the Hub4 Cities, Territories &amp; Mobilities’ Call for proposals 2021. The project proposes a methodology of intervention in the Flaminio district, in particular on the 'Olympic Village' and its relationship with the Tiber River, in line with the Sustainable Development Goals, the Millennium Ecosystem Assessment and the New European Bauhaus, to establish new relationships between cities and the natural environment, favouring sustainable and inclusive public spaces.

Archie model is the basis of calculating oil saturation, but there are some limitations when using this model to calculate oil saturation in water-flooded layer. The main reason is that the main parameters, such as rock resistivity and formation water resistivity, are constantly changing dynamic parameters in the underground with the influence of injected water. Considering that water-flooded layers changes with injection waters, influence factors of rock resistivity and formation water resistivity of primary parameters are analyzed. Considering the dynamic data of water cut is the most reactive underground fluid characteristics of real information, combined with dynamic and static, and the “double ratio” model of later development by the same sedimentary layer is established, which realizes the inversion of rock resistivity and formation water resistivity, then modified Archie model relating to water-flooded layers of the same sedimentary explaining formation. The explanation of actual data indicates that the “double ratio” model well considers the dynamic variation of production data, which makes the inversion of the flooded rock resistivity relatively accurate, besides, the modified Archie model can accurately calculate the oil saturation of water-flooded layers with a reasonable result, which offers scientific basis for the predicting of remaining oil distribution rules.

The presented results of simulations take into account the optical parameters of the selected sea region (from literature data on the southern Baltic Sea) and two optically extreme types of crude oil (from historical data) which exist in the form of a highly diluted oil-in-water emulsion (10 ppm). The spectral index was analyzed based on the results of modelling the radiance reflectance distribution for almost an entire hemisphere of the sky (zenith angle from 0 to 80o). The spectral index was selected and is universal for all optically different types of oil (wavelengths 650 and 412 nm). The possibility of detecting pollution in the conditions of the wavy sea surface (as a result of wind of up to 10 m/s) was studied. It has been also shown that if the viewing direction is close to a direction perpendicular to the sea surface, observations aimed at determining the spectral index are less effective than observation under the zenith angle of incidence of sunlight for all azimuths excluding the direction of sunlight specular reflection.

In this paper, we present a method for detecting and quantifying pathogens in water samples. The method proposes a portable dark field imaging and analysis system for quantifying E. coli concentrations in water after being labeled with magnetic particles. The system utilizes the tracking of moving micro/nano objects close to or below the optical resolution limit confined in small sample volumes (~ 10 µl). In particular, the system analyzes the effect of volumetric changes due to bacteria conjugation to magnetic microparticles (MP) on their Brownian motion while being suspended in liquid buffer solution. The method allows for a simple inexpensive implementation and the possibility to be used as point-of-need testing system. Indeed, a work-ing prototype is demonstrated with the capacity of quantifying E. coli colony forming units (CFU) at a range of 1x10³ - 6x10³ CFU/mL.

Wave breaking is one of the most important yet poorly understood water wave phenomena. It is via wave breaking that waves dissipate most of their energy and the occurrence of wave breaking directly influences several environmental processes, from ocean-atmosphere gas exchanges to beach morphodynamics. Large breaking waves also represent a major threat for navigation and for the survivability of offshore structures. This paper provides a systematic search for intermediate to deep water breaking waves with particular focus on the elusive occurrence of plunging breakers. Using modern remote sensing and deep learning techniques, we identify and track the evolution of over four thousand unique wave breaking events using video data collected from La Jument lighthouse during ten North Atlantic winter storms. Out of all identified breaking waves (Nb=4683), ≈22% were dominant breaking waves, that is, waves that have speeds within [0.77cp, 1.43cp], where cp is the peak wave speed. Correlations between the occurrence rate of dominant breaking waves (that is, waves per area and time per peak wave period) and wave steepness and wave age were observed. As expected, the number of identified plunging waves was small and six waves of all detected breaking waves, or 0.13%, could undoubtedly be considered as plunging waves. Two waves were also identified as unusually large, or rogue waves. Although afflicted by several technical issues, the data presented here provides a good indication that the probability of occurrence of plunging waves should be better incorporated into the design of offshore structures, particularly the ones that aim to harvest energy in offshore environments.

In this work, we propose simple and robust technique for the retrieval of underlying surface spectral albedo using spaceborne observations. It can be used to process both multispectral moderate resolution satellite data and also multi - zone high spatial resolution data. The technique can work automatically for different types of land surfaces without using huge databases accumulated in advance. The new cloud discrimination and retrieval of the water vapor content in atmosphere procedures are presented. The key point of the proposed atmospheric correction technique is the suggested single-wavelength method for determining the atmospheric aerosol optical thickness without reference to a specific type of underlying surface spectrum. The retrievals of spectral albedo for various land surfaces with developed technique, performed using computer simulation and experimental data, have demonstrated a high retrieval accuracy.

In the Lower Yarmouk Gorge the chemical composition of regional, fresh to brackish, mostly thermal groundwater reveal a zonation in respect to salinization and geochemical evolution, which is seemingly controlled by the Lower Yarmouk fault (LYF) but does not strictly follow the morphological Yarmouk Gorge. South of LYF the artesian Mukeihbeh well field produces in its central segment groundwaters of almost pure basaltic-rock type with low contribution (<0.3 vol-%) of Tertiary brine, hosted in deep Cretaceous and Jurassic formations. Further distal, the contribution of limestone water increases originating from the Ajloun Mts. North of the LYF, the Mezar wells, the springs of Hammat Gader and Ain Himma produce dominantly limestone water, which contains 0.14-3 vol-% of the Tertiary brine and possess hence variable salinity. The total dissolved equivalents of solutes gained by water/rock interaction (WRI) and mixing with brine, TDE(WRI+brine), amounts to 10-70 % in the region comprising the Mukheibeh field, Ain Himma and Mezar 3 well, to 55-70 % in the springs of Hammat Gader, and to 80-90 % in wells Mezar 1 and 2. The type of salinization indicates that the Lower Yarmouk fault seemingly acts as the divide between the Ajloun and the Golan Heigths dominated groundwater.

Undoubtedly the Wageningen B-screw Series is the most widely used systematic propeller series. It is very popular to preselect propeller dimensions during the preliminary design stage before performing a more thorough optimization, but in the smaller end of the market it is often used to merely select the final propeller. Over time the originally measured data sets were faired and scaled to a uniform Reynolds number of 2·10⁶ to increase the reliability of the series. With the advent of the computer, polynomials for the thrust and torque values were calculated based on the available data sets. The measured data are typically presented in the well-known open-water curves of thrust and torque coefficients K_T and K_Q versus the advance coefficient J. Changing the presentation from these diagrams to efficiency maps reveals some unsuspected and surprising behaviours, such as multiple optima when optimizing for efficiency or even no optimum at all for certain conditions. These artefacts get more pronounced at higher pitch to diameter ratios and low blade numbers. The present work builds upon the paper presented by the author at the AMT’17 and smp’19 conferences and now includes the extended efficiency maps, as suggested by Danckwardt, for all propellers of the Wageningen B-screw Series.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Decision tables have been used for many years in data processing and business applications to simulate complex rule sets. Several computer languages have been developed based on rule systems and they are easily programmed in several current languages. Land management and river-reservoir models simulate complex land management operations and reservoir management in highly regulated river systems. Decision tables are a precise yet compact way to model the rule sets and corresponding actions found in these models. In this study, we discuss the suitability of decision tables to simulate management in the river basin scale Soil and Water Assessment Tool (SWAT+) model. Decision tables are developed to simulate automated irrigation and reservoir releases. A simple auto irrigation application of decision tables was developed using plant water stress as a condition for irrigating corn in Texas. Sensitivity of the water stress trigger and irrigation application amounts were shown on soil moisture and corn yields. In addition, the Grapevine Reservoir near Dallas, Texas was used to illustrate the use of decision tables to simulate reservoir releases. The releases were conditioned on reservoir volumes and flood season. The release rules as implemented by the decision table realistically simulated flood releases as evidenced by a daily NSE (Nash-Sutcliffe Efficiency) of 0.52 and a percent bias of -1.1%. Using decision tables to simulate management in land, river and reservoir models was shown to have several advantages over current approaches including: 1) mature technology with considerable literature and applications, 2) ability to accurately represent complex, real world decision making, 3) code that is efficient, modular and easy to maintain, and 4) tables that are easy to maintain, support, and modify.

In common model testing practise, the measured values of the self propulsion test are split into the characteristics of the hull, the propeller and into the interaction factors. These coefficients are scaled separately to the respective full scale values and subsequently reassembled to give the power prediction. The accuracy of this power prediction depends {\em inter alia} on the accuracy of the measured values and the scaling procedure. An inherent problem of this approach is, that it is virtually impossible to verify each single step, because of the complex nature of the underlying problem. In recent years the scaling of the open-water characteristics of propeller model tests attracted a renewed interest, fuelled by competitive tests, which became the norm due to requests of the customer. This paper will show the influence of different scaling procedures on the predicted power. The prediction is compared to the measured trials data and the quality of the prediction will be judged. The procedures examined are the standard ITTC~1978 procedure plus derivatives of it: the Meyne, the strip method and the βᵢ-method.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

Dietary assessment methods recognized as appropriate for the general population are usually applied in a similar manner to athletes, despite knowledge that sport-specific factors can complicate assessment and impact accuracy in unique ways. As dietary assessment methods are used extensively within the field of sports nutrition, there is concern the validity of methodologies have not undergone more rigorous evaluation in this unique population sub-group. The purpose was to systematically review studies comparing two or more methods of dietary assessment, including dietary intake measured against biomarkers or reference measures of energy expenditure, in athletes. Six electronic databases were searched for English-language, full-text articles published from January 1980 until June 2016. The search strategy combined the following keywords: diet, nutrition assessment, athlete and validity; where the following outcomes are reported but not limited to: energy intake, macro and/or micronutrient intake, food intake, nutritional adequacy, diet quality, or nutritional status. Meta-analysis was performed on studies with sufficient methodological similarity, with between-group standardized mean differences (or effect size) and 95 % confidence intervals (CI) calculated. Of the 1624 studies identified, 18 were eligible for inclusion. Studies comparing self-reported energy intake (EI) to energy expenditure assessed via doubly labelled water were grouped for comparison (n=11) and demonstrated mean EI was under-estimated by 19 % (- 2793 ± 1134 kJ/d). Meta-analysis revealed a large pooled effect size of - 1.006 (95% CI: -1.3 to -0.7; p<0.001). The remaining studies (n=7) compared a new dietary tool or instrument to a reference method(s) (e.g. food record, 24-h dietary recall, biomarker) as part of a validation study. This systematic review revealed there are limited robust studies evaluating dietary assessment methods in athletes. Existing literature demonstrates substantial variability between methods, with under and misreporting of intake frequently observed. There is a clear need for careful validation of dietary assessment methods, including emerging technical innovations, among athlete populations.

The two-stage direct thermal contact (2sDTC) process is a rapid dewatering approach for fluid fine tailings (FFT) that is integrated into an oil sands bitumen extraction plant to reduce tailings pond storage and freshwater usage. In the first stage, combustion gas directly contacts atomized FFT, vaporizing water and yielding dry solids and steam-rich hot gas. The second stage involves pond effluent water directly contacting the steam-rich hot gas, recovering heat and condensing moisture. Case studies confirm the technical feasibility of the integration. Benefits include producing a dry discharge, reducing tailings water discharge and conserving an equivalent to 0.2 barrels of freshwater per barrel of oil produced. Most importantly, these benefits incur no additional energy cost to the plant as the integration eliminates the energy penalty and CO2 emissions associated with FFT dewatering. Further capacity enhancement can be achieved by using centrifuge-concentrated FFT. The study reveals that FFT concentrated to ~50 wt% solids could still maintain its pump-ability and be accommodated by the 2sDTC process, leading to an integration which could dewater more FFT annually and conserve more freshwater ( 0.58 barrels per barrel of oil produced), with the sole energy requirement being the power to drive the centrifuge machinery.

This review explores the transformative role of artificial intelligence (AI) in the entire winemaking process, from viticulture to bottling, with a particular focus on enhancing food safety and traceability. It discusses AI’s applications in optimizing grape cultivation, fermentation, bottling, and quality control, while emphasizing its critical role in managing microbiological risks such as mycotoxins. The review aims to show how AI technologies not only refine operational efficiencies but also raise safety standards and ensure traceability from vineyard to consumer. Challenges in AI implementation and future directions for integrating more advanced AI solutions into the winemaking industry will also be discussed, providing a comprehensive overview of AI's potential to revolutionize traditional practices.

Irritable bowel syndrome (IBS) is one of the most common gastrointestinal diseases in humans. It is characterized by visceral pain and/or discomfort, hypersensitivity and abnormal motor responses along with change in gut habits. Although the etio-pathogenesis of IBS is only partially understood, a main role has been attributed to psychosocial stress of different origin. Animals models such as neonatal maternal separation, water avoidance stress and wrap restraint stress have been developed as psychosocial stressors in the attempt to reproduce the IBS symptomatology and identify the cellular mechanisms responsible for the disease. The study of these models has led to the production of drugs potentially useful for IBS treatment. This review intends to give an overview on the results obtained with the animal models; to emphasize the role of the enteric nervous system in IBS appearance and evolution and as a possible target of drug therapies.

To understand the physiological basis of tolerance to combined stresses to low phosphorus (P) and drought in mungbean (Vigna radiata (L.) R. Wilczek), a core set of 100 accessions were evaluated in hydroponics at sufficient (250 μM) and low (3 μM) P, and exposed to drought (dehydration) stress. The principal component analysis and ranking of accessions based on relative values revealed that IC280489, EC397142, IC76415, IC333090, IC507340 and IC121316 performed superior while IC119005, IC73401, IC488526 and IC325853 performed poorly in all treatments. Selected accessions were evaluated in soil under control (sufficient P, irrigated), low P (without P, irrigated), drought (sufficient P, withholding irrigation) and combined stress (low P, withholding irrigation). Under combined stress, a significant reduction in gas exchange traits (photosynthesis, stomatal conductance, transpiration, instantaneous water use efficiency), P uptake in seed and shoot was observed under combined stress as compared to individual stresses. Among accessions, IC488526 was most sensitive while IC333090 and IC507340 exhibited tolerance to individual or combined stress. The water balance and low P adaptation traits like membrane stability index, relative water content, specific leaf weight, organic acid exudation, biomass, grain yield and P uptake can be used as physiological markers to evaluate for agronomic performance. Accessions with considerable resilience to low P and drought stress can be either used as ‘donors’ in Vigna breeding program or cultivated in areas with limited P and water availability or both.

It is estimated that 3 billion tons of concrete are used globally each year. Cement is a critical component of concrete, and its production accounts for nearly 5-7% of global carbon dioxide (CO2) emissions. Producing one ton of concrete (OPC) releases approximately one ton of CO2. These CO2 emissions contribute to the greenhouse effect, leading to global warming, polar ice cap melting, sea level rise, coastal city flooding, land desertification, decreased agricultural productivity, ecosystem damage, and adverse effects on human health. This situation is concerning, and there is an urgent need to minimize CO2 emissions from the cement industry. This paper focuses on incorporating various materials into concrete to increase its strength and reduce emissions of CO2 and other harmful substances, thereby mitigating the impacts of the greenhouse effect and achieving the great vision of carbon neutrality. The study theoretically analyzes the issues of coconut shell disposal in Southeast Asia and waste tire disposal in Europe and the United States. This paper uses Abaqus to model and analyze various green concretes and compares the data with that of ordinary concrete.

Earth Observation (EO) techniques have significantly evolved over time, covering a wide range of applications in different domains. The scope of this study is to review the research conducted on EO in the Eastern Mediterranean, Middle East, and North Africa (EMMENA) region and to identify the main knowledge gaps. We searched through the Web of Science database for papers published between 2018 and 2022 for EO studies in the EMMENA. We categorized the papers in the following thematic areas: Atmosphere, Water, Agriculture, Land, Disaster Risk Reduction (DRR), Cultural Heritage, Energy, Marine Safety and Security (MSS) and Big Earth Data (BED); 6647 papers were found with the highest number of publications in the thematic areas of BED (27%) and Land (22%). Most of the EMMENA countries are surrounded by sea, yet there was a very small number of studies on MSS (0.9% of total number of papers). This study detected a gap in fundamental research in the BED thematic area. Other future needs identified by this study are the limited availability of very high resolution and near real time remote sensing data, the lack of harmonized methodologies and the need for further development of models, algorithms, early warning systems and services.

Vibrio vulnificus (Vv) is a bacterial pathogen native to warm and brackish water ecosystems that can cause fatal septicemia (Vv-vibriosis) in humans and various farmed fish species. From a One Health perspective, controlling Vv-vibriosis outbreaks on farms is essential not only for animal but also for human health, as it reduces the risk of Vv transmission to humans. Electrolyzed water (EW) is a sustainable control method, exhibiting transient disinfectant properties due to the formation of hypochlorous acid (HOCl). We hypothesized that EW could effectively reduce Vv populations in aquaculture facilities, preventing outbreak emergence. To test this hypothesis, survival assays in EW were conducted under varying conditions of salinity, pH, and free available chlorine (FAC). The results indicated that an intermediate concentration of FAC had a significant bactericidal effect on Vv populations regardless of the condition and tested strain. Consequently, the strategic use of EW could serve as an eco-friendly preventive and control measure against Vv-vibriosis by significantly decreasing the bacterial load in farm water.

Cold-water coral (CWC) reefs represent vulnerable marine ecosystems (VMEs) of critical ecological importance. This study presents a novel approach for the automated detection and segmentation of key CWC species, Desmophyllum pertusum and Madrepora oculata, in underwater imagery using the YOLOv8l-seg deep learning model. The model was applied to images collected at two Natura 2000 sites in the Cantabrian Sea: the Avilés Canyon System (ACS) and El Cachucho Seamount (CSM). Results demonstrate the model's high accuracy in identifying and delineating individual coral colonies. Significant variability in coral cover was observed between and within the study areas, highlighting the patchy nature of CWC habitats. Three distinct coral community groups were identified based on percentage coverage composition and abundance, with the highest coral cover group being located exclusively in the La Gaviera canyon head within the ACS. This research demonstrated the potential of deep learning models for efficient and accurate monitoring of VMEs, facilitating the acquisition of high-resolution data essential for understanding CWC distribution, abundance, and community structure, and contributing to the development of effective conservation strategies.