As the most commonly used hydrogel material in contact lenses, the amount of water in a lens affects its optical properties and comfort for the wearer. Therefore, an important challenge is to determine the safety and efficacy of contact lenses by accurately and non-destructively measuring the water content in real time. In this study, we demonstrate the accurate detection of water content in hydrogel contact lenses using a high-precision ATR format in a portable terahertz time-domain spectroscopy system. The technique can resolve small variations in the dielectric constant in solution, which is difficult to achieve with traditional transmission and reflection measurement modes. Information is obtained from the interaction between the sample and the swift waves propagating along the prism surface. The swift waves can excite longitudinal modes that are not directly accessible by conventional techniques. It is worth noting that the reference wave can be measured by removing the sample without disturbing the optical path. We also enhance the plasma effect at the interface with the hydrogel by using PVDF dielectric films of different polarities. We observed that the water content and refractive index changes in the ATR mode show different response patterns for nonpoled PVDF and poled PVDF membranes. This suggests that reflection and relative phase can be accurately evaluated in the THz-ATR technique, resulting in an accurate method for determining complex dielectric constants in the reflection geometry. This will allow accurate measurement of both surface and in vivo water content in hydrogels in the future and is a potential technical route for application in bioaqueous tissue measurements.

Desktop fused filament fabrication (FFF) 3D printers have been growing in popularity among hobbyist and professional users as a prototyping and low-volume manufacturing tool. One issue these printers face is the inability to determine when a defect has occurred rendering the print unusable. Several techniques have been proposed to detect such defects but many of these approaches are tailored to one specific fault (e.g., filament runout/jam), use expensive hardware such as laser distance sensors, and/or use machine vision algorithms which are sensitive to ambient conditions, and hence can be unreliable. This paper proposes a versatile, reliable, and low-cost system, named MTouch, to detect millimeter-scale defects that tend to make prints unusable. At the core of MTouch is an actuated contact probe designed using a low-power solenoid, magnet, and hall effect sensor. This sensor is used to check for the presence, or absence, of the printed object at specific locations. The MTouch probe demonstrated 100% reliability, which was significantly higher than the 74% reliability achieved using a commercially available contact probe (the BLTouch). Additionally, an algorithm was developed to automatically detect common print failures such as layer shifting, bed separation, and filament runout using the MTouch probe. The algorithm was implemented on a Raspberry Pi mini-computer via an Octoprint plug-in. In head-to-head testing against a commercially available print defect detection system (The Spaghetti Detective), the MTouch was able to detect faults 44% faster on average while only increasing the print time by 8.49%. In addition, MTouch was able to detect faults The Spaghetti Detective was unable to identify such as layer shifting and filament runout/jam.

Plate fin-tube heat exchangers are widely used in air conditioning and refrigeration systems and other industry fields. Various errors made in the manufacturing process can result in the formation of an air gap between the tube and fin. Several numerical simulations were carried out for a symmetric section of plate fin-tube heat exchanger to study the influence of air gap on heat transfer under periodic flow conditions. Different locations and sizes of an air gap spanning 1/2 circumference of the tube were considered for the range of airflow velocities. Velocity and temperature fields for cases with air gap were compared with ideal thermal contact cases. Blocking of heat flow by the gap leads to the reduction of heat transfer rate. Fin discontinuity in the front of the tube causes the smallest reduction of the heat transfer rate in comparison to the ideal tube-fin contact, especially for thin slits. The rear gap position is the worst in the smallest gap range. Therefore, reversing the flow direction can lead to up to a 15% heat transfer increase, if mainly the rear gaps are present. The introduction of a thin slit in the front of the tube leads to convective heat transfer enhancement, which should be further investigated.

We analyzed the characteristics of the Severe Acute Respiratory Syndrome Coronavirus-2 (SARS-CoV-2) infected children during lock-down period in Catalonia (Spain), and their transmission role within the households. Among 295 traced household contacts of 89 pediatric patients, children were classified as final index cases in only 3.4% of the traced homes.

To improve water injection effect, microemulsions (MEs) were used to wet coal seam compared with water and sodium dodecyl sulfate solution (SDS). Wetting effects were characterized by contact angle, X-ray diffraction, Fourier infrared spectroscopy. The results showed that the microemulsion has better spreadability on coal surface and has stronger wettability for coals of different ranks and different particle sizes than traditional wetting agents. The W/O type microemulsion is more affinity to coal than the O/W type and the bicontinuous type.Oxygen and hydrogen contents contributed to wetting. Different wetting agents have the greatest impact on the oxygen-containing functional group absorption zone of coal, but have little impact on the change of clay mineral composition.As the content of quartz increased, the content of montmorillonite was decreased, and the hydrophilicity of coal was increased. This research proposes new ideas for solving coal dust problems and reducing coal mine disasters.

Modelling water vapour flow, heat transfer and porosity in porous adsorbent is somewhat challenging simulation problem. Primary macroscopic water vapour flow models, such as Darcy's law, fail to predict the pressure drop entirely correctly for the reason that many of flow parameters not considered because of the simplifications that remain made for the multi-scale structure of the porous adsorbents. For one to develop a good physical understanding of such water vapour flows and the accuracy of existing 3D simulation models, there is a need for some accurate 3D geometry to be studied. This present work describes two-phase water vapour flow and adsorption/ desorption performed on porous adsorbent by a Dynamic vapour sorption (DVS). The CFD simulation results are associated with experiments results. It is decided that for such complex porous adsorbent CFD simulation problems the use of COMSOL Multiphysics and SolidWorks flow simulation will be utilised.

This research explores the predictive capabilities of autonomous driving systems by integrating human factor considerations within the context of safety-critical events. Recognizing the significance of human behaviors in influencing driving dynamics, the study employs advanced modeling techniques to enhance the accuracy of predictions in scenarios that demand heightened safety measures. Traditional rule-based systems and monotonic logic often fall short in addressing the complexities of safety-critical events. To overcome these limitations, the research proposes the application of non-monotonic logic, allowing for flexible and adaptive reasoning that accommodates exceptions and context-specific information.The study emphasizes the importance of incorporating individual differences among drivers, such as risk-taking tendencies, reaction times, decision-making processes, and driving styles. By considering these human factors, the research aims to develop realistic and accurate autonomous driving models that capture the nuances of real-world driving scenarios, especially in safety-critical situations. The predictive model takes into account both internal and external factors, enabling the autonomous system to anticipate and respond effectively to unforeseen events.The primary goal is to provide autonomous vehicles with the capability to make plausible inferences, handle conflicting data, and adapt their behavior in real-time during safety-critical events. The proposed model integrates personalized cognitive agents for each driver, incorporating their unique preferences, characteristics, and needs. This personalized approach aims to optimize the safety and efficiency of autonomous driving, contributing to the ongoing evolution of intelligent transportation systems.In conclusion, this research contributes to advancing the field of autonomous driving by introducing a predictive model that leverages human factor considerations to enhance safety in safety-critical events. The incorporation of non-monotonic logic and individualized cognitive agents signifies a comprehensive approach to address the challenges associated with predicting autonomous driving behavior, paving the way for safer and more reliable autonomous vehicles in dynamic and unpredictable environments.

In the present study, a mathematical model of non-steady partial differential equation from the process of oxygen mass transport in the human pulmonary circulation is proposed. Mathematical modelling of this kind of problems lead to a non-steady partial differential equation and for its numerical simulation, we have used finite differences. The aim of the process is the exact numerical analysis of the study, wherein consistency, stability and convergence is proposed. The necessity of doing the process is that, we would like to increase the order of numerical solution to a higher order scheme. An increment in the order of numerical solution makes the numerical simulation more accurate, also makes the numerical simulation being more complicated. In addition, the process of numerical analysis of the study in this order of solution needs more research work.

Except for a few species, the outer shape of vertebrates normally is characterized by bilateral symmetry. The inner organs, on the other hand, normally are arranged in bilaterally asymmetric patterns, which are of special importance for the normal function of the cardiovascular system of lung-breathing vertebrates. Deviations from the normal organ asymmetry can occur in the form of mirror imagery of the normal arrangement (situs inversus), or in the form of arrangements that have the tendency for development of bilateral symmetry, either in a pattern of bilateral left-sideness (left isomerism) or bilateral right-sidedness (right isomerism). The latter two forms of visceral situs anomalies are called “heterotaxy syndromes”. During the past 30 years, remarkable progress has been made in uncovering of the genetic etiology of heterotaxy syndromes. However, the pathogenetic mechanisms causing the spectrum of cardiovascular defects found in these syndromes remain poorly understood. In the present report, a spontaneous case of left cardiac isomerism found in a HH-stage 23 chick embryo is described. The observations made in this case suggest that hearts with left cardiac isomerism may have the tendency for development of a non-compaction cardiomyopathy caused by defective development of the proepicardium.

Cycloid drives are generally used in precision machinery requiring high reduction ratios, such as robot joint (RV) reducers, in which the contact load and stress property of the internal meshing pairs greatly affect the dynamic transmission performance of the reducers. Therefore, in this study, Isogeometric Analysis (IGA) was employed to explore the multi-tooth contact problem of the cycloid pinwheel drive. Based on the NURBS curved surface generation method, the NURBS tooth profile of the cycloid gear was reconstructed. In addition, the NURBS surface of the cycloid gear - pin tooth - output pin was generated via the element splicing method. A geometrical analysis model of cycloid pinwheel drive was established to solve the contact force of the meshing pair under different input angles, and compared with the finite element method in terms of convergence, resultant accuracy, and solving timeliness. The results show that the Isogeometric analysis has higher accuracy and efficiency than the finite element method in calculating the contact stress and contact force. This method can improve the contact simulation accuracy of the cycloid drive and provides a reference for the design evaluation of RV reducer.

The aim of this study was to evaluate the biomechanical changes of the cornea after wearing soft contact lenses (CLs) in healthy myopic patients measured with the Corvis ST® analyzer. This prospective, cross-sectional, single-center study was performed in twenty-two Caucasian patients aged between 19 and 24 years (20.64 ± 1.21 years) range). Five device-specific biomechanical parameters, central corneal thickness and intraocular pressure were measured prior to fitting and one month after CLs wear. Differences between the means of the DA Ratio and the standard deviation of the DA Ratio pre- and post-CLs wear were found to be significant (p value=0.002 in both cases). Significant differences were found between pre- and post-CLs wear values in CCT (p value=0.013). For all other biomechanical measures, no significant differences were observed before and after treatment. A significant association was found between changes in bIOP and classification according to changes in Int. Radius (p value = 0.047) and SSI (p value = 0.026) standard deviations. The corneal biomechanical indices provided by CST demonstrate that fitting of soft CLs is a safe optical compensation method for the stability of corneal stiffness. No significant differences were found pre- and post-CLs wear in the assessment of bIOP.

Despite their anti-icing ability, hydrophobic coatings have the disadvantages of easy falling off and poor wear resistance, resulting in insufficient durability of ice/snow melting. To improve the surface stability and durability of superhydrophobic coatings, nanoparticle/epoxy coatings were prepared with three types of nanoparticles, two types of dispersion methods, three types of application methods and two types of introduction methods of epoxy resin. Water contact angles, ice adhesion force and icing rate of asphalt concrete coated with hydrophobic coatings were tested. The molecular structures of coatings were analyzed by Fourier transform infrared spectroscopy. The surface morphology of hydrophobic coatings was observed using Scanning electron microscopy. Results indicated that nano-ZnO, TiO2 and SiO2 particles can be modified into hydrophobicity by stearic acid. The hydrophobic coating could improve the hydrophobicity of concrete, reduce the adhesion strength of ice and asphalt concrete and delay the beginning icing time. Moreover, The dosages of stearic acid, nanoparticle and epoxy resin need to be in a certain range to ensure the best hydrophobicity and durability of coatings.

(1) Background: Formation of biofilms on food-contact surfaces by Shiga-toxigenic Escherichia coli (STEC) can pose a significant challenge to the food industry, making conventional control-methods insufficient. Targeted use of bacteriophages to disrupt these biofilms could reduce this problem. Previously isolated and characterized bacteriophages (n=52) were evaluated against STEC biofilms in-vitro and on food-contact surfaces. (2) Methods: Phage-treatments (9 logs PFU/ml), in phosphate-buffered-saline, were used individually or as cocktails. Biofilms of STEC (O157, O26, O45, O103, O111, O121, and O145) were formed in 96-well micro-titer plates (7 logs CFU/ml; 24 h) or on stainless-steel (SS) and high-density-polyethylene (HDPE) coupons (9 logs CFU/cm2; 7 h), followed by phage-treatment. Biofilm-disruption was measured in-vitro at 0, 3, and 6 h as a change in optical-density (A595). Coupons were treated with STEC-serotype-specific phage-cocktails or a 21-phage cocktail (3 phages/serotype) for 0, 3, 6 and 16 h and surviving STEC populations enumerated. (3) Results: Of the 52 pages, 77% showed STEC-biofilm disruption in-vitro. Serotype-specific phage-treatments reduced pathogen population within the biofilms by 1.9-4.1 and 2.3-5.6 logs CFU/cm2, while the 21-pahge cocktail reduced it by 4.0 and 4.8 logs CFU/cm2 on SS and HDPE, respectively. (4) Conclusions: Bacteriophages can be used to reduce STEC and their biofilms.

The modeling of tilting-pad journal and thrust bearings presents a level of complexity beyond that of bearings of fixed-arc geometry, particularly with regard to dynamic influences. With tilting-pad bearings, the theory surrounding the fluid film must be complemented with representative modeling of the pad dynamics. What has been recognized in recent decades has been the significance of the pad support, in particular the flexibility of the pivot region of the pad. The typical model for including the stiffness of the pivot has been based on Hertzian contact theory. Some researchers have been noting that the Hertzian theory does not permit sufficient flexibility in the pivot region. It is suggested that the contact mechanics at the pivot would be better represented as a pairing of rough surfaces. The modeling used here is based on a statistical asperity micro-contact theory for rough-surface line contact that has been extended to include contact stiffness. This model has been applied to the determination of the effective dynamic properties of tilting-pad bearings. The results show that pivot stiffness can be as low as one-third the stiffness determined by Hertzian theory. Comparison to published experimental results confirms the significance of the rough-surface modeling, particularly for the line contacts associated with rocker-back tilting pads.

Between October 2021 and April 2022, 317 outbreaks caused by highly pathogenic avian influen-za (HPAI) H5N1 viruses were notified in poultry farms in the northeastern Italian Regions. The complete genomes of 214 strains were used to estimate the genetic network based on the virus similarity. An exponential random graph model (ERGM) was used to assess the effect of at-risk contacts, same owners, in-bound/out-bound risk windows overlap, genetic differences, geograph-ic distances, same species and poultry company, on the probability of observing a link within the genetic network, which can be interpreted as the potential propagation of the epidemic via lateral spread or a common source of infection. The variables same poultry company (Est.=0.548, C.I.=[0.179;0.918]) and risk windows overlap (Est.=0.339, C.I.=[0.309;0.368]) were associated with a higher probability of link formation, while the genetic differences (Est.=-0.563, C.I.=[-0.640;-0.486]) and geographic distances (Est.=-0.058, C.I.=[-0.078;-0.038]) indicated a re-duced probability. The integration of epidemiological data with genomic analyses allows moni-toring the epidemic evolution and helps explain the dynamics of lateral spreads suggesting the potential diffusion routes. The 2021-2022 epidemic stresses the need to further strengthen the bi-osecurity measures, and to encourage the reorganisation of the poultry production sector to mini-mize the impact of future epidemics.

Particle deposition on the surface of the drying chamber poses the main drawback in the spray drying process, which reduces the product recovery and affects the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber was investigated in this study. The hydrophobic Polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless-steel substrates, which were used to mimick the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X1, %) and the treatment duration (X2, hr) on the contact angle of the substrate (°), which reflected the hydrophobicity of the surface. A three-dimensional (3D) response surface was constructed to examine the influence of the PDMS concentration and treatment duration on the contact angle readings, which serve as an indicator of the surface's hydrophobic characteristic. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 4.94 hr, while the PDMS coating for the stainless-steel substrate achieved an optimum contact angle of 98.31° with PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 1 hr. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH3, CH2, and CH3 functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and uniform nanostructure on the surface of PDMS-treated substrates, which indicated the reduction of wettability and the potential effect on unwanted biofouling on the spray drying chamber.

Contact tracing is one of the oldest social network health interventions used to reduce the diffusion of various infectious diseases. However, some infectious diseases like COVID-19 amass at such a great scope that traditional methods of conducting contact tracing (e.g., face-to-face interviews) remain difficult to implement, pointing the need to develop reliable and valid survey approaches. The purpose of this research is to test the effectiveness of three different egocentric survey methods for extracting contact tracing data: (1) a baseline approach, (2) a retrieval cue approach, and (3) a context-based approach. A sample of 397 college students were randomized into one of each condition and were prompted to anonymously provide contacts and populated places visited from the past four days. After controlling for various demographic, social identity, psychological, and physiological variables, participants in the context-based condition were significantly more likely recall more contacts (medium effect size) and places (large effect size) than the other two conditions. Theoretically, the research supports suggestions by field theory that assume network recall can be significantly improved by activating relevant activity foci. Practically, the research contributes to developing innovative social network data collection methods for contract tracing survey instruments.

The widely spread CoronaVirus Disease (COVID)- 19 is one of the worst infectious disease outbreaks in history and has become an emergency of primary international concern. As the pandemic evolves, academic communities have been actively involved in various capacities, including accurate epidemic estimation, fast clinical diagnosis, policy effectiveness evaluation and development of contract tracing technologies. There are more than 23,000 academic papers on the COVID-19 outbreak, and this number is doubling every 20 days while the pandemic is still on-going [1]. The literature, however, at its early stage, lacks a comprehensive survey from a data analytics perspective. In this paper, we review the latest models for analyzing COVID19 related data, conduct post-publication model evaluations and cross-model comparisons, and collect data sources from different projects.

This work attempted to fabricate superhydrophobic fabric via simple immersion technique. Textile fabrics were coated with silica nanoparticles prepared from tetraethoxysilane (TEOS) to obtain sufficient roughness with hydrophobic surface chemistry. Then the coated fabrics were treated with polydimethylsiloxane (PDMS) and aminopropyltriethoxysilane (APTES) to reduce the surface energy. The effects of PDMS concentration on the surface morphology and superhydrophobicity of as-prepared fabric were investigated. The morphology and the composition of superhydrophobic fabric was characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDS) and Fourier transform infrared (FTIR) spectroscopy. The results revealed the formation of spherical silica nanoparticles with average particle size of 250 nm throughout the fabric surface. The possible interactions between silica nanoparticles and APTES, as well as the fabrics were elucidated. Investigating the hydrophobicity of fabrics via water contact angle (WCA) measurement showed that the treated fabric exhibits excellent water repellency with a water contact angle as high as 151° and a very low water sliding angle. It also found that the treated fabric maintained most of its hydrophobicity against repeated washing. The comfort properties of the obtained superhydrophobic fabrics in term of air permeability and bending length did not reveal any significant changes.

True contact between solids with randomly rough surfaces tends to occur at a large number of microscopic contact patches. So far, two scaling regimes have been identified for the number density n(A) of contact-patch sizes A in elastic, non-adhesive, self-affine contacts. At small A, n(A) is approximately constant, while n(A) decreases as a power law at large A. Using Green’s function molecular dynamics, we identify a characteristic (maximum) contact area Ac above which a superexponential decay of n(A) becomes apparent if the contact pressure is below the pressure p_cp at which contact percolates. We also find that A_c increases with load relatively slowly far away from contact percolation. Results for A_c can be estimated from the stress autocorrelation function G_σσ (r) with the following argument: the radius of characteristic contact patches, r_c, cannot be so large that G_σσ (r_c) is much less than p_c². Our findings provide a possible mechanism for the breakdown of the proportionality between friction and wear with load at large contact pressures and/or for surfaces with a large roll-off wavelength.

Platelets have long been associated with sustaining the balance between hemostasis and thrombosis. Platelets, however, are also involved in a wide range of biological activities, including inflammation, immunology, wound healing, cancer biology, and angiogenesis. Platelets' diverse roles are mediated by the expression of various adhesive and immune receptors and the secretion of a diverse array of bioactive proteins, ions stored in granules, and several lipid mediators. Platelets also release pro-inflammatory and anti-inflammatory, and angiogenic factors and shed microparticles into the bloodstream. The challenge for therapeutic intervention in non-hemostatic disease is identifying the factors that primarily inhibit specific targets implicated in platelets' complicated contribution to inflammation or tumor growth while leaving their hemostatic function intact. In addition, blood platelets are involved in infection and innate and adaptive immunity by mediating complicated vascular homeostasis via specialized receptors and granule release, RNA transfer, and mitochondrial secretion. Anti-platelet drugs/bioactive compounds are developed based on their platelet anti-aggregatory properties; however, very little information is available on their effects on non-hemostatic function. Therefore, a better understanding of the impact of the anti-platelet bioactive on the platelets' diverse roles and mechanisms may help develop new strategies and prevent CVD and other diseases. In this review, a comprehensive overview of platelet multifunctional roles in CVD and other diseases and dietary factors' modulatory effects are described.

This paper presents a new method to model the nonlinear behaviour of masonry double curvature structures, possibly reinforced by composite materials, by means of conventional elasto-plastic analyses. It is meant to be used in professional design, especially for assessment and retrofitting purposes, therefore based on the exploitation of the simplest nonlinear Finite Elements available in a commercial software, namely trusses with elasto-fragile and elasto-ductile behaviour (Cutoff Bars). The numerical static nonlinear analyses are carried out by considering elastic hexahedral elements for bricks and lumping nonlinearities on joints. These have been assumed in turn elastic-brittle and elastic-plastic by using 1D elements, respectively Point Contacts, under No-Tension Material hypothesis, and Cutoff Bars, assigning small tensile resistance to the material. The reinforcement, realised with FRP hooping strips, has been successfully modelled in a similar fashion, i.e. by applying perfectly bonded elastic-plastic Cutoff Bars at the extrados of the dome, where the debonding is accounted for in a conventional way limiting the tensile strength according to Italian Standards indications. The procedure is validated against benchmark models with the same geometry, using experimental data and more refined structural model results for comparison.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

Cell mechanics is a biophysical indicator of cell state, such as cancer metastasis, leukocyte activation, and cell cycle progression. Atomic force microscopy (AFM) is a widely used technique to measure cell mechanics, where the Young modulus of a cell is usually derived from the Hertz contact model. However, the Hertz model assumes that the cell is an elastic, isotropic, and homogeneous material and that the indentation is small compared to the cell size. These assumptions neglect the effects of the cytoskeleton, cell size and shape, and cell environment on cell deformation. In this study, we investigated the influence of cell size on the estimated Young’s modulus using liposomes as cell models. Liposomes were prepared with different sizes and filled with phosphate buffered saline (PBS) or hyaluronic acid (HA) to mimic the cytoplasm. AFM was used to obtain the force indentation curves and fit them to the Hertz model. We found that the larger the liposome, the lower the estimated Young’s modulus for both PBS-filled and HA-filled liposomes. This suggests that the Young modulus obtained from the Hertz model is not only a property of the cell material, but also depends on the cell dimensions. Therefore, when comparing or interpreting cell mechanics using the Hertz model, it is essential to account for cell size.

Private Set Intersection (PSI) is a cryptographic method in secure multi-party computation that allows entities to identify common elements in their datasets without revealing their private data. Traditional approaches assume similar-sized datasets and equal computational power, overlooking practical imbalances. In real-world applications, dataset sizes and computational capacities often vary, particularly in the Internet of Things and mobile scenarios where device limitations restrict computational types. Traditional PSI protocols are inefficient here, as computational and communication complexities correlate with the size of larger datasets. Thus, adapting PSI protocols to these imbalances is crucial. This paper explores unbalanced PSI scenarios where one party (the receiver) has a relatively small dataset and limited computational power, while the other party (the sender) has a large amount of data and strong computational capabilities. It introduces three innovative solutions for unbalanced PSI: unbalanced PSI protocol based on Cuckoo filters, unbalanced PSI protocol based on single cloud assistance, and unbalanced PSI protocol based on dual cloud assistance, each addressing the shortcomings of the previous solution. These protocols primarily optimize database computational load, storage capacity, protocol execution time, and security. Depending on performance and security needs, different protocols can be employed for applications such as private contact discovery.

In voice analysis, the electroglottographic (EGG) signal has long been recognized as a useful complement to the acoustic signal, if only when the vocal folds are actually contacting, such that this signal has an appreciable amplitude. However, phonation can occur also without vocal fold contacting, as in breathy voice, in which case the EGG amplitude is low, but not zero. It is of great interest to identify the transition from non-contacting to contacting, because this will substantially change the nature of the vocal fold oscillations; yet that transition is not in itself audible. The magnitude of the normalized peak derivative of the EGG signal is a convenient indicator of contacting, but no current EGG hardware has a sufficient signal-to-noise ratio of the derivative. The textbook techniques of spectral thresholding and static notch filtering are straightforward to implement, can run in real time, and can mitigate several noise problems in EGG hardware.

Solid tumors universally possess the ability to evade contact inhibition of proliferation (CIP), a mechanism halting cell proliferation when cell-cell contacts occur. Merlin, an ERM-like protein, crucially regulates CIP and is frequently deactivated in various cancers, indicating its signifi-cance as a tumor suppressor in cancer biology. Despite extensive investigations into Merlin's role in cancer, its lack of intrinsic catalytic activity and frequent conformation changes has made it notoriously challenging to study. To address this challenge, we harnessed innovative luciferase technologies to create and validate a split-luciferase biosensor system. This system enables precise quantification of Merlin's conformation and activity both in vitro and within living cells. This biosensor significantly enhances the study of Merlin's molecular functions, serving as a potent tool to explore its contributions to CIP and tumorigenesis.

The application of dry lubrication in rolling contacts is challenging due to wear. In previous studies graphene platelets applied as dry lubricants on the surfaces of angular contact ball bearings demonstrated superior properties. These specific bearings, experiencing both rolling and spinning motion, create more severe conditions for dry lubricants. The applied graphene platelets have a thickness of few graphene layers in the nm range and a diameter in the µm range. Such platelets can be produced by mechanical exfoliation from graphite. To delve deeper into the lubrication effects, investigations were carried out using a milli tribometer. In the tests, a fixed steel ball is sliding against an oscillating counterpart under defined load. During the measurements, the applied load and tangential forces on the ball are recorded to calculate the friction. In our case, a steel ball with a diameter of 6 mm was used against graphene-based films on flat bearing surfaces (axial bearing washer). Comparative investigations included nano graphite particles and fullerene as dry lubricants, in addition to graphene platelets of various staple thicknesses. To increase the adhesion of the films to the surfaces, a pre-rolling process was implemented. Afterwards, the friction on the compressed films was measured. The results indicate that the pre-rolling process effectively reduces the friction of the system. After testing, the surfaces underwent analysis using laser scanning microscopy to assess the formed films, wear, and material transfer. It has been demonstrated that the pre-rolling process leads to the formation of a very thin compacted film with surface protective properties. On the ball as counterpart, the graphene platelets generate a transfer film on the contacting surface.

Overuse and misuse of antibiotics can pose the risks of spreading mutant strains that show antimicrobial resistance (AMR), with negative impact on management of bacterial infections and economic implications on healthcare systems. Research and development of natural antibacterial agents could be a priority in the next years to improve number of effective antibacterial molecules and to reduce AMR phenomenon and its development. The present study identified the most effective concentration and contact time of Thymus vulgaris L. essential oil (TEO) to obtain bactericidal effect in vitro against different Gram + and Gram – bacterial strains. Six clinically isolated (wild types) bacterial strains, (Citrobacter freundii, Enterococcus feciorum, Proteus mirabilis, Acinetobacter cioffi, Pasteurella putrefaciens, Klebsiella pneumoniae) and two ATCC (Staphylococcus aureus and Streptococcus mutans) were tested after 1min, 3min and 5min of contact with TEO. Preliminary results on S. aureus after 24h incubation revealed a TEO concentration of 9.28mg/mL (w/v) that completely inhibited bacteria growth keeping cell viability. Total suppression of bacterial growth at all tested contact times was observed for all tested bacterial strains and the results were confirmed after 48h incubation. Bacterial growth suppression was confirmed even with presence of organic component. These preliminary results showed in vitro antimicrobial efficacy of TEO against different Gram+ and Gram- bacterial strains. Future studies are necessary to confirm the reproducibility of these results even on other strains and to define exactly the molecular mechanisms of EOs, in order to consider TEO as a valid alternative of classic antibiotic therapies and subsequently to reduce the occurrence of AMR.

In previous studies regarding the osseointegration of zirconia (ZrO2) implants, a lack of consistency was observed in the surface topographies of the ZrO2 and Ti samples because of the difficult processability of ZrO2 surfaces. To resolve this problem, we used the molecular precursor method (wet process), which is a surface-modifying technique that can easily change the surface chemistry without changing the surface topography. A roughened Ti surface was prepared using sandblasting (large-grit) and acid treatment. We were able to create ZrO2-coated Ti implants with the same topography as that of roughened Ti substrates using the molecular precursor method, which solution contained a Zr complex. The uniform presence of tetragonal Zr was confirmed, and the apparent zeta potential of the surface of the ZrO2-coated Ti implant was higher than that of Ti. In animal experiments, ZrO2-coated Ti implants showed an equivalent or higher bone-to-implant contact ratio compared to that of the non-coated implants inserted into the femur bone defects of the rats. ZrO2 with the same surface topography as that of roughened Ti exhibits a promotion of osteogenesis equivalent to or better than that of Ti in the early stages of bone formation.

This paper proposes a contact force controller for a constrained flexible manipulator in three-dimensional motion. This controller used the conversion formula obtained empirically and experimental results showed the effectiveness of the proposed contact force controller. First, the manipulator was operated with the tip of the second link restrained, then, time response of the root strain, joint angles and contact force were used to derive the relational between the three quantities. The effectiveness of the relational expression was verified by conducting a target contact force tracking experiment by inputting the angle from the relational expression. The contact force control using the strain feedback method was proposed with the strain amount estimated from the target contact force as the target value, and its effectiveness was verified by experiments. From the results obtained, controller using the strain feedback method was designed for the purpose of controlling the contact force at the tip of a flexible manipulator with two links and three degrees of freedom that performs three-dimensional spatial motion, and its effectiveness was shown by comparison with the contact force feedback method.

Contact tracing has become an indispensable tool of various extensive measures to control the spread of COVID-19 pandemic due to novel coronavirus. This essential tool helps to identify, isolate and quarantine the contacted persons of a COVID-19 patient. However, the existing contact tracing applications developed by various countries, health organizations to trace down the contacts after identifying a COVID-19 patient suffers from several security and privacy concerns. In this work, we have identified those security and privacy issues of several leading contact tracing applications and proposed a blockchain-based framework to overcome the major security and privacy challenges imposed by the applications. We have discussed the security and privacy measures that are achieved by the proposed framework to show the effectiveness against the security and privacy issues raised by the existing mobile contact tracing applications.

The purpose of this work was analysing the compaction of a cohesive material using different DEM simulators to determine the equivalent contact models and identify how some parameters of the simulations affect the compaction results (maximum force and compacts appearance) and computational costs. For that purpose, three cohesion contact models were tested (‘linear cohesion’ in EDEM; ‘SJKR’ and ‘SJKR2’ in LIGGGHTS). The influence of the particle size distribution (PSD) on the results was also investigated. Further assessments were performed on the effect of selecting different timesteps, using distinct conversion tolerances for exporting the 3D models to STL files and moving the punch with different speeds. Consequently, it was possible to determine that a timestep equal to a 10% Rayleigh timestep, a conversion tolerance of 0.01 mm and a punch speed of 0.2 m/s are adequate for simulating the compaction process using the contact models in this work. In addition, the results determined that the maximum force was influenced by the PSD because of the rearrangement of the particles. The PSD was also related to the computational cost because of the number of simulated particles and their sizes. Finally, an equivalence was found between the linear cohesion and SJKR2 contact models

This paper is referred to a top frontline research in life science, showing that in spite of the large variation of the physiological architecture and behavioral forms of the living systems, the fundamental structure of their informational system is basically the same, allowing the body growth/development by micro to macro-structuration processes, maintaining the same informational configuration and functions like the basic unit of life – the eukaryotic cell. Starting and based on the determination of the special/specific info-operability in living structures and the role of information in structuration and their functionality, there are discussed the informational functions of the eukaryotic/prokaryotic cells, the simplest units of life and is elaborated and presented the Informational Model of the Living Structures, showing that these structures operate on the basis of two main informational systems: one of them defined as the Programmed Informational System, composed by three components, assuring respectively the info-generation, maintenance and the proliferation/reproduction, and another one defined as the Operative Informational System, necessary for the continuous communication with the environment for adaptation, consisting in four main components referred to memory, decision, sentience and info-connection/info-selection. The revealed properties are compared with the Informational System of the Human Body, as a prototype of a living system on the top of the evolutionary scale, showing/demonstrating the compatibility of structuration and functions on the entire scale, from prokaryotic/eukaryotic unit cells to multicellular organisms – plants, animals and human, by means of a continuous adaptation process, which always follows the same line of micro to macro-structuration process based on the same Info-organization and functionality. These models are new and revolutionary in the information and life sciences

: Cybersecurity has become a critical area in the digital field in recent years. The expansion of networks has revolutionised the way network structures are organised and managed. However, with increased connectivity and the growing complexity of modern networks, the threat of cyber-attacks has become more intense. As technology continues to advance, it brings both opportunities and challenges. One of the major challenges is the need to secure networks and sensitive data from various malicious activities. Traditional networks have evolved to include Software Defined Network (SDN), which offers a more flexible and programmable framework. Researchers should focus on detecting attacks in SDN because SDN networks are becoming more popular and attractive targets for clients due to their programmability and dynamic nature. The centralised controller, known as the backbone of an SDN, becomes a single point of failure and a potential target for attackers if not properly secured. Researchers need to emphasise the detection of attacks in SDN in order to mitigate these risks. By understanding the potential vulnerabilities and attack methods specific to SDN, researchers can develop effective detection approaches and propose countermeasures. This methodology helps protect the network from potential threats and minimises the impact of successful attacks. Therefore, this survey paper provides a review of Intrusion Detection Systems (IDSs) in Software-Defined Networks (SDN) to provide a thorough understanding of SDN security issues.

The establishment of a well characterized non-human primate model of Zika virus (ZIKV) infection is critical for the development of medical interventions. In this study, challenging Indian rhesus macaques (IRMs) with ZIKV strains of the Asian lineage resulted in dose dependent peak viral loads between days 2 and 5 post infection; and a robust immune response which protected the animals from homologous and heterologous re-challenge. In contrast, viremia in IRMs challenged with an African lineage strain was below the assays lower limit of quantitation and the immune response was insufficient to protect from re-challenge. These results corroborate previous observations but are contrary to reports using other African strains obviating the need for additional studies to elucidate the variables contributing to the disparities. Nonetheless, the utility of an Asian lineage ZIKV IRM model for countermeasures development was verified by vaccinating animals with a formalin inactivated reference vaccine and demonstrating sterilizing immunity against a subsequent subcutaneous challenge.

Cultural practices and development level can influence a population’s household structures and mixing patterns. Within some populations households can be organized across multiple dwellings. This likely affects the spread of infectious disease spreads through these communities, however, current demographic data collection tools do not record these data. Methods: Between June–October 2018, the Contact And Mobility Patterns in remote Aboriginal Australian communities (CAMP-remote) pilot study recruited Aboriginal mothers with infants in a remote northern Australian community to complete a monthly iPad-based contact survey. Results: Thirteen mother-infant pairs (participants) completed 69 study visits between recruitment and the end of May 2019. Participants reported they and their other children slept in 28 dwellings during the study. The median dwelling occupancy, defined as people sleeping in the same dwelling on the previous night, was nine (range: 3.5–25). Participants who completed at least three responses (n=8) slept in a median of three dwellings (range: 2–9). Each month a median of 28% (range: 0%–63%) of the participants travelled out of the community. Including these data in disease transmission models amplified estimates of infectious disease spread in the study community, compared to models parameterized using census data. Conclusions: The lack of data on mixing patterns in populations where households can be organized across dwellings may negatively impact the accuracy of infectious disease models for these communities and the efficacy of public health actions they inform.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

Guided by the Conceptual Model of Implementation Research, we explored the acceptability, appropriateness, and feasibility of: 1) automated screening approaches utilizing existing health data to identify those who require subsequent diagnostic evaluation for familial hypercholesterolemia (FH) and 2) family communication methods including chatbots and direct contact to communicate information about inherited risk for FH. Focus groups were conducted with 22 individuals with FH (2 groups) and 20 clinicians (3 groups). These were recorded, transcribed, and analyzed using deductive (coded to implementation outcomes) and inductive (themes based on focus group discussions) methods. All stakeholders described these initiatives as: 1) acceptable and appropriate to identify individuals with FH and communicate risk with at-risk relatives; and 2) feasible to implement in current practice. Stakeholders cited current initiatives, outside of FH (e.g., pneumonia protocols, colon cancer and breast cancer screenings), that gave them confidence for successful implementation. Stakeholders described perceived obstacles, such as nonfamiliarity with FH, that could hinder implementation and potential solutions to improve systematic uptake of these initiatives. Automated health data screening, chatbots, and direct contact approaches may be useful for patients and clinicians to improve FH diagnosis and cascade screening.

Arthropod-borne viruses belonging to the flavivirus genus possess an enormous relevance in public health. Neotropical non-human primates (NPs) have been proposed to be infected more frequently with flaviviruses due to their arboreal and diurnal habits, their genetic similarity to humans and their relative closeness to humans. However, the only known flavivirus in America that is maintained by sylvatic cycles involving NPs is Yellow Fever virus (YFV), and the NPs role as potential hosts of flaviviruses is still unknown. Here, we examined flavivirus exposure in 86 free range and captive NPs of Costa Rica to evaluate their involvement in flavivirus transmission cycles and their potential as flavivirus hosts. We used a highly-specific micro plaque reduction neutralization test (micro-PRNT) to determine the presence of antibodies against YFV, Dengue virus 1-4 (DENV), Zika virus, West Nile Virus (WNV) and Saint Louis Encephalitis virus (SLEV). We found evidence of seropositive NPs to DENV-1 8.2% (homotypic –3/86, heterotypic – 4/86), SLEV 15.1% (homotypic – 10/86, heterotypic – 2/86), WNV 2.3% (homotypic – 2/86) and 8.1% (7/86) undetermined Flavivirus species. No antibodies against YFV or ZIKV were found. This work provides compelling serological evidence of exposure in NPs of flaviviruses associated with urban cycles, i.e. DENV, and confirms decades of circulation of SLEV in the same environments. Also, the range of years of sampling and the socioeconomic region was statistically significant for the presence of Dengue and Flavivirus undetermined seropositive individuals, respectively. Both the years and socioeconomic regions with greater seroprevalence coincide with the years and socioeconomic regions with high numbers of Dengue human cases for the country. Our work suggests bidirectional? circulation of different flaviviruses between humans and wildlife with public health importance and underscores the necessity of further surveillance for flaviviruses in the humans/wildlife interface in Central America.

Microarray gene expression-based detection and classification of medical conditions have been prominent in research studies over the past few decades. However, extracting relevant data from the high-volume microarray gene expression with inherent nonlinearity and inseparable noise components raises significant challenges during data classification and disease detection. So, this paper proposes a two-level strategy involving feature extraction and selection methods before the classification step. The feature extraction step utilizes Short Term Fourier Transform (STFT), and the feature selection step employs Particle Swarm Optimization (PSO) and Harmonic Search (HS) metaheuristic methods. The classifiers employed are Non-Linear Regression, Gaussian Mixture Model, Softmax Discriminant, Naive Bayes, SVM (Linear), SVM (Polynomial), and SVM (RBF). The two-level extracted relevant features are compared with raw data classification results, including Convolutional Neural Network (CNN) Methodology. Among the methods, STFT with PSO feature selection and SVM (RBF) classifier produced the highest accuracy of 94.47%.

Reporting on CSR activities has become the essence of reporting for modern business entities. In this regard, particular attention is paid to public interest companies. Therefore, the following paper aims to answer the question of whether there are differences in the linguistic structure of the studied CSR reports in three selected industry indices on the Warsaw Stock Exchange (WSE) in Poland, i.e. WIG-energy index, WIG-fuel index, WIG-mining index and their relationship with the performance of selected companies. The study was conducted on a purposely selected sample of companies between 2013 and 2018. A total of 138 CSR reports and 138 annual separate financial statements prepared in accordance with international balance sheet law were collected. The study was carried out based on a panel regression model. It was found that CSR reports contained similar average percentages of parts of speech such as nouns and adjectives. When linking the economic performance of companies, expressed with selected indices, to the information on the implementation of CSR concepts, it was revealed that the results are more likely to describe business performance when it is satisfactory.

Background and objectives: The initiation of apoptotic death in cancer cells is the aim of many chemotherapeutic strategies. As many anticancer agents have been discovered in natural plant sources, the search for novel phytochemicals displaying anticancer activities continues at a tremendous rate. This study was conducted to evaluate the effect of extractable polyphenols (EPP); non-extractable polyphenols (NEPP); nobiletin (NOB); tectorigenin (TEC) and persicogenin (PERS) from Barhi date palm kernels (BDPK) extracts on the induction of apoptosis in human lung cancer A549 and colon cancer HT29 cell lines. Materials and Methods: The anticancer activities were determined using MTT and trypan blue exclusion assays. Flow cytometry analysis was performed to study the cell viability, cell cycle arrest and apoptosis. The underlying mechanism of apoptosis induced by crude extracts and the purified compounds was investigated using caspase-3, -8 and -9 assays and the mitochondrial membrane potential assay. Results: The findings indicate that both BDPK extracts and the purified compounds do exert induced cell death on A549 and HT29 cells. The results observed from MTT- assay and trypan blue exclusion indicate that the cytotoxic effects of both plant extracts and the three isolated flavonoids are dose-dependent with higher cell death after 72 hours treatment. Treatment of human lung and colon cancer cells with EPP, NEPP, NOB, TEC and PERSI induced late stages of apoptosis as there was evidence of the DNA degradation and high percentage of the cells population was situated at sub-G1 phase, indicating a high population of apoptotic cells. Conclusions: Study of the apoptotic mechanism demonstrated that EPP and NEPP exhibited dependent mitochondrial signalling pathway as seen with caspase-9 and induced receptor-mediated (extrinsic) apoptotic pathway as seen with caspase-8. Therefore, our results suggest that BDPK extracts and the three isolated flavonoids could be a good candidate for developing anticancer agents.

Despite great technical capabilities, the theory of non-contact temperature measurement is usually not fully applicable to the use of measuring instruments in practice. While black body calibrations are in practice well established and easy to accomplish, this calibration protocol is never fully applicable to measurements of real objects under real conditions. Currently, the best approximation to real world radiation thermometry is grey body radiation thermometry, which is supported by most measuring instruments to date. Nevertheless, the metrological requirements necessitate traceability, therefore real body radiation thermometry is required for temperature measurements of real bodies. This article documents the current state of temperature calculation algorithms for radiation-thermometers and the creation of a traceable model for radiation thermometry of real bodies that uses a digital twin model of the system of measurement to compensate for the loss of data, caused by spectral integration, which occurs when thermal radiation is absorbed on the active surface of the sensor. To solve this problem, a hybrid model with variable scalar inputs is proposed, in which the scalar input parameters are calculated to correspond to the system of measurement. The method for calculating the effective parameters is proposed and verified with the theoretical model of non-contact thermometry. The sum of effective instrumental parameters is presented for different temperatures to show that the rule of radiation thermometry of grey bodies, according to which the sum of instrumental emissivity and instrumental reflectivity equals to 1, does not hold in radiation thermometry for real bodies. Using the derived models of radiation thermometry, the uncertainty of radiation thermometry due to the uncertainty of spectral emissivity is analysed by simulated measurements along the temperature ranges of various radiation thermometers, enabling traceable non-contact temperature measurements with known measurement uncertainty under any known conditions.

The distribution of oil and gas phases around ball-raceway local regions is an important basis and foundation for determining whether a bearing is sufficiently lubricated. To obtain the oil phase distribution law in the inner raceway-ball contact local region (IBCR) and outer raceway-ball contact local region (OBCR) of the under-race lubrication ball bearing, the numerical simulation method is used. The effects of bearing rotation speed, oil flow rate, oil viscosity and oil density on these two regions are studied. The results indicate that the oil phase exhibited significant periodic changes in both time and space. Compared with that in the IBCR, the oil phase distribution in the OBCR is more uniform. Increasing the bearing rotation speed and reducing the oil flow rate made the IBCR and OBCR more uniform. Changing the oil viscosity only alters the distribution pattern of the OBCR. The oil density may not affect the fluid flow state or the oil phase distribution in the bearing.

Jump rope is a widely-applied basic training in various sports, yet it is understudied biomechanically. This study investigates the impact of cycle-tempo-induced motor control changes in elite jump rope athletes, addressing the biomechanical gap of cyclic skill control. The hypothesis posited two accelerations per jump cycle—one in front of and one behind the body—and anticipated that increased cycle frequency would alter the distribution of acceleration time within a cycle. Using 3D motion analysis, kinematic parameters were obtained and analyzed. The results confirmed the presence of two distinct accelerations per cycle. As tempo increased, the percentage of rear acceleration time increased while front acceleration time decreased, along with peak velocities increasing significantly (p<0.01). Rope trajectory analysis indicated a consistent movement pattern across tempos, primarily in the sagittal plane. Variations in skill control showed shorter contact phases and reduced vertical range of motion for the center of gravity and feet at higher tempos (p<0.05), along with significant reductions in joint range of motion for the lower limbs (p<0.01). These findings enhance the understanding of motor control adaptations to different tempos and have practical implications for developing coaching programs aimed at optimizing performance, stability, and efficiency in jump rope training.

This study was aimed to assess visual performance and overall satisfaction of extended depth of focus (EDOF) contact lenses (CLs) in a presbyopic population. We prospectively investigated visual acuity at all distances (0.3, 0.4, 0.5, 0.7, 1, and 5 m), higher-order aberrations (HOAs), contrast sensitivity function, and, overall satisfaction score, before and during EDOF CL wear. Binocular visual acuity at 0.3, 0.5, 0.7, 1, 2, 3, and 5 m when wearing EDOF CLs was 0.01 ± 0.14, -0.08 ± 0.02, -0.08 ± 0.02, -0.08 ± 0.00, -0.08 ± 0.00, -0.08 ± 0.02, and -0.07 ± 0.02, respectively. We found a significant improvement at near to intermediate distances (0.3, and 0.5 m), but no significant change at intermediate to far distances (0.7, 1, 2, 3, and 5 m) between before and during CL wear. The area under the log contrast sensitivity function was not significantly changed neither under photopic nor mesopic conditions (p=0.099, and p=0.689). Ocular third-order aberrations, fourth-order aberrations or total HOAs for a 4-mm pupil significantly increased. The overall satisfaction score significantly improved by wearing EDOF CLs. EDOF CLs significantly improved visual acuity at near to intermediate dis-tances, while maintaining far vision, and the effect of contrast sensitivity was minimal, suggesting its viability of presbyopic correction in such candidates.

Current methods for the hardening step of functional coatings over different materials imply the use of high temperatures, high energy consumption or long periods of time, which have repercussions on the speed and cost of the product. We report here a simple and low cost methodology for the functionalization of low cost stainless steel, which is modular, depending of the functionality pursued: a levelling layer for smooth the surface of the material, an “easy to clean” property, or both of them. The research is based on sol-gel coatings cured under UV light without requiring high thermal hardening processes making it applicable to plastics and other sensible materials and possessing high chemical and thermal stability. The film ensures lower processing costs, and higher rates of hardening if the adequate medium-pressure lamps are employed. This formulation is also well defined for scaling up the process, so it is possible to perform a continuous coating in large areas by employing mild processing conditions (low temperature, atmospheric pressure). In addition, the sol gel solution was fully characterized and studied in order to guarantee a long service life before deposition, with a focus on industrial applications in the domestic sector.

Fungal keratitis (FK) is a serious ocular infection that often poses significant diagnostic and therapeutic dilemmas. This study aimed to examine the causes, clinical characteristics, outcomes, and prognostic factors of FK in the UK. All culture-positive and culture-negative presumed FK (with complete data) that presented to Queen’s Medical Centre, Nottingham, and Queen Victoria Hospital, East Grinstead, between 2011 and 2020 were included. A total of 117 patients (n=117 eyes) with FK were included in this study. The mean age was 59.0±19.6 years (range, 4-92 years) and 51.3% patients were female. Fifty-three fungal isolates were identified from 52 (44.4%) culture-positive cases, with Candida spp. (33, 62.3%), Fusarium spp. (9, 17.0%), and Aspergillus spp. (5, 9.4%) being the most common organisms. Ocular surface disease (60, 51.3%), prior corneal surgery (44, 37.6%), and systemic immunosuppression (42, 35.9%) were the three most common risk factors. Hospitalisation for intensive treatment was required for 95 (81.2%) patients, with a duration of 18.9±16.3 days. Sixty-six (56.4%) patients required additional surgical interventions for eradicating the infection. Emergency therapeutic/tectonic keratoplasty was performed in 29 (24.8%) cases, though 13 (44.8%) of them failed at final follow-up. The final corrected-distance-visual-acuity (CDVA) was 1.67±1.08 logMAR. Multivariable logistic regression analyses demonstrated increased age, large infiltrate size (>3mm), and poor presenting CDVA (<1.0 logMAR) as significant negative predictive factors for poor visual outcome (CDVA of <1.0 logMAR) and poor corneal healing (>60 days of healing time or occurrence of corneal perforation requiring emergency keratoplasty; all p<0.05). In conclusion, FK represents a difficult-to-treat ocular infection that often results in poor visual outcome, with a high need for surgical interventions. Innovative treatment strategies are urgently required to tackle this unmet need.

Predator-prey interactions present heightened opportunities for pathogen spillover, as predators are exposed to novel parasites through consumption of prey harboring potentially infectious agents. Epizootics with high morbidity and mortality have been recorded following prey-to-predator spillover events with significant conservation implications, particularly for sensitive species. However, relatively few virulent infections following prey consumption are reported, given the very large number of exposures that presumably occur. Further, many transmitted agents are infectious but clinically silent and thus go unrecognized. Mechanisms that determine outcome of predator exposure to prey-based pathogens therefore represent an important, understudied component of disease dynamics that should be considered in modeling approaches and empirical research to better understand disease risk and emergence, particularly in vulnerable or threatened species.

This communication reports an improvement of the quality of the electrical data obtained from the application of electrical resistivity tomography method on archaeological studies. The electrical contact between ground and electrode enhances significantly by using carbomer-based gel during the electrical resistivity tomography measurements. Not only does the gel promote the conservation of the building surface under investigation, but it also virtually eliminates the necessity of conventional spike electrodes, which in many archaeological studies are inadequate or not permitted. Results evidenced an enhancement in the quality of the electrical data obtained in the order of thousands of units compared with those without using the carbomer-based gel. The potential and capabilities of this affordable gel make it appropriate to be applied to other geoelectrical studies beyond archaeological investigations. Moreover, it might solve corrosion issues on conventional spike electrodes, and electrical multicore cables usually provoked for added saltwater attempting to improve the electrical contact.

This study aimed to evaluate the hazards posed by foodborne bacteria of the Listeria genus by analyzing prevalence, diversity and virulence of Listeria spp. in food and food manufacturing plants. Seventy five isolates obtained from the routine analysis of 653 samples by three diagnostic laboratories in Northern Italy were genotipically differentiated by Repetitive Extragenic Palindrome (rep) PCR with the GTG5 primer, identified by sequencing the 16S rRNA gene and examined by specific PCR tests for the presence of L. monocytogenes virulence determinants occasionally found to occur in other species of the genus. The identity of the amplification products was confirmed by sequencing. Fifty seven isolates were identified as L. innocua, 12 as L. monocytogenes, 5 as L. welshimeri and one as L. seeligeri. All L. monocytogenes isolates belonged to the serotype 1/2a and were predicted to be virulent for the presence of the inlJ internalin gene. Potentially virulent strains of L. innocua, L. seeligeri and L. welshimeri, carrying the L. monocytogenes inlA gene and/or hly gene, were identified, and most isolates were found to possess the toxin-antitoxin system mazEF for efficient adaptation to heat shock. Results indicated the need to reinforce food contamination prevention measures against all Listeria species by efficiently defining their environmental distribution.

In the world industry plant, solid and solid metals are always in contact even their motions not independent. Modeling of rolling die contact with slab primarily needs to describe the Tribology of contact phenomena. Consideration of continuum theory of rolling contact how a contact region is formed between rolling die and slab, and how the tangential force is distributed over the contact area with coefficient of friction is important. The central concern of numerical model is used in this work to indicate a set of equations, derived from the contact principle, that transfer the physical event into the mathematical equations including the laws of nature, such as newton’s laws, boundary conditions, state of stresses and their derivatives at particular time and locations. In this paper the elasticity stress behavior of rolling die contact with slab for number of cyclic loads is modeled. The model is including new proposed constitutive equations for discontinuity of the velocity, pressure distribution in rolling contact from the enter side to exit side of the neutral point. To verify the model, finite element simulation and experimental data from the literature are considered. The results show good agreement with finite element simulation and experimental data.

The function of the endoplasmic reticulum (ER) can be impaired by the alternation of the extra- and intracellular environment such as disruption of calcium homeostasis, expression of mutated proteins and oxidative stress. In response to disruptions to ER homeostasis, eukaryotic cells activate canonical branches of signal transduction cascades, collectively termed the unfolded protein response (UPR). The UPR attempts to recover the protein folding capacity and avoid irreversible cellular damage. Additionally, the UPR has been shown to play unique physiological roles in the regulation of diverse cellular events, including cell differentiation and development and lipid biosynthesis. Recent studies have indicated that these important cellular events are also regulated by contact and communication among organelles. These reports suggest strong involvement among the UPR, organelle communication and regulation of cellular homeostasis. However, the precise mechanisms for the formation of contact sites and the regulation of its dynamics by UPR remain unresolved. In this review, we summarized the current understanding of how the UPR regulates morphological changes to the ER and the formation of contact sites between the ER and other organelles. We also review how UPR-dependent connections between the ER and other organelles affect cellular and physiological functions.

The function of the endoplasmic reticulum (ER) can be impaired by the alternation of the extra- and intracellular environment such as disruption of calcium homeostasis, expression of mutated proteins and oxidative stress. In response to disruptions to ER homeostasis, eukaryotic cells activate canonical branches of signal transduction cascades, collectively termed the unfolded protein response (UPR). The UPR attempts to recover the protein folding capacity and avoid irreversible cellular damage. Additionally, the UPR has been shown to play unique physiological roles in the regulation of diverse cellular events, including cell differentiation and development and lipid biosynthesis. Recent studies have indicated that these important cellular events are also regulated by contact and communication among organelles. These reports suggest strong involvement among the UPR, organelle communication and regulation of cellular homeostasis. However, the precise mechanisms for the formation of contact sites and the regulation of its dynamics by UPR remain unresolved. In this review, we summarized the current understanding of how the UPR regulates morphological changes to the ER and the formation of contact sites between the ER and other organelles. We also review how UPR-dependent connections between the ER and other organelles affect cellular and physiological functions.

Abstract Due to the relatively low efficiency of thermoelectric (TE) generators, they have mostly been used in niche applications where the unique properties of TE generators outweigh their lack of efficiency, or conditions where it is more reasonable to base the optimal design on maximum generated power rather than maximum efficiency. The aim of this work is to investigate how the different fundamental transport properties (Seebeck coefficient, thermal conductivity and electrical resistivity) in materials with equal figure of merit (ZT) impact TE module design and maximum power output. Further, we discuss and review the strategies to enhance material properties and the latest studies on the TE module performance. It is shown, that by increasing the power factor by a factor of 15 and decreasing the thermal conductivity by 13.33 in order to maintain ZT=1, power output is increased by 45%. This effect is stronger in lower module fill factor and thermal resistance of the heat source and heat sink.

Pain is a major problem in sick newborn infants, especially for those needing intensive care. Pharmacological pain relief is the most commonly used but may be ineffective, have side effects, including long-term neurodevelopmental sequelae. The effectiveness and safety of alternative analgesic methods are ambiguous. The objective is to review the effectiveness and safety of non-pharmacological methods of pain relief in newborn infants and to identify those that are the most effective. PubMed and Google Scholar were searched using the terms: ‘infant’, ‘premature’, ‘pain’, ‘acupuncture’, ‘skin to skin contact’, ‘sucrose’ ‘massage’, ‘musical therapy’ and ‘breastfeeding’. We included 24 studies assessing different methods of non-pharmacological analgesic techniques. Most resulted in some degree of analgesia but many were ineffective and some were even detrimental. Sucrose, for example, was often ineffective but more effective than music therapy, massage, breast milk (for extremely premature infants) or non-invasive electrical stimulation acupuncture. There were also conflicting results for acupuncture, skin to skin care and musical therapy. Most non-pharmacological methods of analgesia provide some modicum of relief for preterm infants but none are completely effective and there is no clearly superior method. Study is also required to assess potential long-term consequences of any of these methods.

Brake wear particles, as the major component of non-exhaust particulate matter, are known to have different emissions, depending on the type of brake assembly and the specifications of the vehicle. In this study, brake wear and wear particle mass emissions were measured under realistic vehicle driving and full friction braking conditions using current commercial genuine brake assemblies. Although there were no significant differences in either PM₁₀ or PM_2.5 emissions between the different cooling air flow rates, brake wear decreased and ultrafine particle (PM_0.12) emissions increased with increasing cooling air flow rate. Particle mass measurements were collected on filter media, allowing chemical composition analysis to identify the source of brake wear particle mass emissions. The iron concentration in the brake wear particles indicated that the main contribution was derived from disc wear. Using a systematic approach that measured brake wear and wear particle emissions, this study was able to characterize correlations with elemental compositions in brake friction materials, adding to our understanding of the mechanical phenomena of brake wear and wear particle emissions.

In a single-center, retrospective study, 22 cases were enrolled and divided into two groups: those who underwent surgical wide excision (group A) and those who did not (group B). The study included 13 cases in group A and 9 cases in group B. In group A, 6 cases solely underwent surgical wide excision, while 7 cases received additional treatments like radiotherapy or chemotherapy. Conversely, in group B, 4 cases received chemotherapy, 4 cases received radiotherapy, and 1 case was managed through observation alone. The mean follow-up time was 60.15 months in group A and 43.44 months in group B, with no significant difference observed. In group A, 9 cases resulted in mortality, whereas 6 cases died within the follow-up period in group B. Lesion-free intervals post-operation were observed predominantly in group A, while 7 cases in group B never experienced freedom from skin lesions. Kaplan-Meier survival curve analysis demonstrated a significant difference between the survival curves of the two groups (P = 0.046). Among non-HIV Kaposi’s sarcoma patients, surgical wide excision appears to have a role in treatment. Patients in group A exhibit a more favorable outcome in the survival curve analysis.

Non-melanoma skin cancers (NMSCs) are the leading cause of skin cancer-related morbidity and mortality. Effective strategies are needed to control NMSC occurrence and progression. Non-toxic, plant-derived extracts have been shown to exert multiple anti-cancer effects. Graviola (Annona muricata), a tropical fruit-bearing plant, has been used in traditional medicine against multiple human diseases including cancer. The current study investigated the effects of graviola leaf and stem extract (GLSE) and its solvent-extracted fractions on two human NMSC cell lines, UW-BCC1 and A431. GLSE was found to: i) dose-dependently suppress UW-BCC1 and A431 cell growth, motility, wound closure, and clonogenicity; ii) induce G₀/G₁ cell cycle arrest by downregulating cyclin/cdk factors while upregulating cdk inhibitors, and (iv) induce apoptosis as evidenced by cleavage of caspases-3, -8 and PARP. Further, GLSE suppressed levels of activated hedgehog (Hh) pathway components Smo, Gli 1/2, and Shh while inducing SuFu. GLSE also decreased the expression of pro-apoptotic protein Bax while decreasing the expression of the anti-apoptotic protein Bcl-2. We determined that these activities were concentrated in an acetogenin/alkaloid-rich dichloromethane subfraction of GLSE. Our data identify graviola extracts and their constituents as promising sources for new chemopreventive and therapeutic agent(s) to be further developed for the control of NMSCs

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

Infectious disease like COVID-19 will have a great impact on human society. An effective prevention and control measure is to quickly isolate the source and reduce the population’s exposure to the infection. Therefore, it is very important to quickly trace and identify the virus carrier and its close contacts in order to effectively suppressing transmission. This article provides a method, system and storage medium for locating the source of infection based on big data. We adopt the method of combining Bluetooth and GPS positioning to track the action trajectory of each individual. The method stores the close contact and location information locally and update on the cloud platform for an appropriate period of time. The method and system can provide personal risk levels and regional risk levels through related algorithms. When entering a high-risk area or if the personal risk level within the Bluetooth interconnection range is greater than the set threshold, an alarm function is provided. We can also generate reports on the spread of the epidemic over a period of time. As a result, the system can quickly locate the source of infection and close contacts, providing a reference for quick and highly efficient epidemic prevention and control.

Being one of the most critical phases of a flight, landing deserves specific attention, especially when the aircraft is subject to external disturbances such as wind. A notable concern associated with touchdown events, especially when crosswind is present is tire wear. This work is aimed first at developing a nonlinear flight simulator able to handle the entire landing maneuver in non-null wind conditions, considering the airborne phase, ground run, and the transition between them. Then, the simulator is included in an optimal process to define the landing technique associated with the minimum tire wear. The methodology is tested in a simulation environment with a realistic model of a reference aircraft, showing that a significant reduction of tire wear can be obtained by optimizing the sideslip angle at touchdown and the lateral-directional controls after the airplane touches the runway with both legs of the main landing gear.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

Almost half of the confirmed COVID-19 cases detected so far in the United Kingdom are part of a large cluster of 13 British nationals who tested positive for SARS-CoV-2 in the UK, Spain, and France. Transmissions among this cluster occurred at a ski resort in France, and originated from a single infected traveller returning from a conference in Singapore where he acquired the virus. At least 21 individuals were exposed to the virus, tested, and quarantined, with 13 of those testing positive between the period of 6th Feb and 15th Feb. Here, all publicly available information about the primarily UK/France cluster is consolidated, providing a complete and accessible summary of the cases and their connections. Notable in this cluster are the number of individuals infected, the apparent absence of any severe illness among those infected, and a case of a `delayed positive' test during isolation after initially testing negative, at least 7 days after last possible contact.

Polluted rivers are a primary problem in Changhua County, Taiwan, due to rapid and massive developments in agriculture and industry. In this study, samples consisted of water influent from the Yangzi-Cuo River, Ci-Tong Jiao, Changhua County. Ecology technology, a combination of gravel contact oxidation and surface flow constructed wetlands, was employed to enhance the water quality. Ecology technology is a useful and ordinary process that focuses on original treatment of pollution through chemical, physical, and biological procedures based on the mediums of soil, plant, water, and microorganisms from pure environments. Moreover, this study aimed to minimize the river pollution index (RPI) of the Yangzi-Cuo River by using combinations of gravel contact oxidation and surface flow constructed wetlands. The inflow volume of the water samples in situ was found to be 1534–2261 cubic meters per day (CMD). The pollution in the water sample mostly involved suspended solid (SS), ammoniacal nitrogen (NH₃–N), total phosphorus (TP), total nitrogen (TN), and biochemical oxygen demand (BOD), and the values of the above indexes were found to be 10.0–26.7 mg/L, 0.9–14.0 mg/L, 1.2–14.1 mg/L, 11.1–18.2 mg/L, and 0.5–3.6 mg/L, respectively. Efficiencies of pollution elimination in SS, NH₃–N, TP, TN, and BOD were found to be 24.2–93.1%, 58.3–86.2%, 5.2–85.0%, 59.4–77.2%, and 46.3–76.4%, correspondingly, after purification treatment via ecology technology. Thus, ecology technology is a valid means of purification treatment for polluted rivers.

The utilisation of non-Saccharomyces yeasts in co-inoculation and non-thermal technologies for must sterilisation is becoming increasingly prevalent due to its notable utility and potential. This approach optimises the fermentation process, facilitates the production of wines with distinctive characteristics and enhances their stability. Two trials were conducted concurrently, designated as A and B. The same red must was utilized in both trials, with one undergoing UHPH treatment and the other serving as the control. The non-Saccharomyces yeasts were identical in both trials. In Trial A, different percentages of initial inoculum were employed with respect to the total volume of must to be fermented, with the objective of evaluating the influence and competitiveness between yeasts. Trial B was designed to investigate the impact of two nutrients that provide vitamins, energy and protection from oxidative stress on the development of these yeasts and their metabolic expression. A microbiological analysis was conducted, along with oenological parameter measurements, acidification assessments, volatile compound analyses, and spectrophotometric evaluations. It was observed in both trials that the prevalence of Lachancea thermotolerans (Lt) was longer than that of Metschnikowia pulcherrima (Mp), and that the use of quercetin + thiamine had a positive effect on yeast growth. Furthermore, the combination of Lt and Mp yeasts demonstrated remarkable synergy, resulting in the production of a substantial quantity of lactic acid (&gt;5 g/L). With regard to aroma compounds, the UHPH must exhibited a nearly twofold increase in ethyl lactate. Additionally, the TPI was observed to be 8-10% higher in wines derived from UHPH musts, indicating that this technology may potentially safeguard against oxidation.

The idea of CUAD (contact unmodified antisense DNA) biotechnology and the use of oligonucleotide insecticides (briefly, olinscides, or DNA insecticides) was proposed on lepidopterans and gradually disseminated on hemipteran pests. As the next-generation platform for creation of insecticides, it has a number of unique characteristics (short unmodified antisense DNA as contact insecticide, insect rRNAs as target, DNA containment as mechanism of action) that distinguish it from existing classes of chemical insecticides. Oligonucleotide insecticides possess low carbon footprint, high safety for non-target organisms, rapid biodegradability, avoidance of target-site resistance, ensuring prosperity for agricultural countries that will implement this innovation. As the next-generation class of insecticides olinscides create opportunities that have never existed before in crop protection. Using flexible CUAD platform, any farmer, botanical garden or pest control company is capable of creating its own unique arsenal of insecticides, well-tailored for a particular population of insect pest. Most technological innovations start out very expensive and don't work well, but eventually start working well and become very cheap. CUAD biotechnology has come a long way for 16 years and is very close to the point to be implemented on a large scale against certain groups of pests. In this article we provide basic knowledge of use of oligonucleotide pesticides and list pests (mainly from suborder Sternorrhyncha, Hemiptera) which were successfully controlled by us recently.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

At the highest level of endurance sports, the differences in finishing times are small, so equipment is constantly being constantly improved to enhance the athletes' performance. For instance, one dominant resistive force in connection with cross-country skiing is the friction between the skis and snow and since the 1930s, research designed to understand and reduce this friction has been ongoing. The mechanisms involved in ski-snow friction include compaction, micro-ploughing, adhesion, viscosity, and water-bridging. Of these, adhesive and viscous friction have been most studied, while much less is presently known about compaction, micro-ploughing, and water-bridging. At the macro-scale, the ski-camber profile plays a key role in determining whether, with respect to friction, a particular cross-country ski is suitable for use under a given set of conditions. Through its influence on where ski-snow contact occurs, this ski-camber profile has a profound impact on adhesive and viscous friction, micro-ploughing, the formation of water bridges, and the rate of compaction. Different contact zones with different apparent areas of contact and pressure have been found to be most suitable for different conditions. In addition, the micro-scale texture of the ski base is also an important determinant of ski-snow friction. Topographical measurements of this texture can be achieved with white-light interferometer and recent characterisation has focused on the mechanical properties of contact. In numerous tribological studies the interactions between features at different scales are modelled. In most tribological systems, features on several scales influence friction and ski-snow contact is certainly no exception. Accordingly, the current investigation was designed to evaluate the multi-scale properties of different combinations of two skis with two different base textures. The real area of contact and the average interfacial separation and total average reciprocal interfacial separation between the ski and snow were taken into consideration. We found that different macro- and micro-scale properties of the ski favour different mechanisms of friction. Both the profile of the ski camber and texture of the base play decisive roles in determining viscous friction. At the same time, the texture of the ski base exerts a greater impact on the average real contact pressure, real contact area and minimal average interfacial separation between the ski and snow than does the ski-camber profile.

In order to realize the performance degradation trend prediction accurately, a prediction method based on multi-domain features and temporal convolutional network (TCN) is proposed. Firstly, construct a high-dimensional feature set in the multi-domain of vibration signals, and use comprehensive evaluation indicators to preliminarily screen performance degradation indexes with good sensitivity and strong trend. Secondly, the kernel principal component analysis (KPCA) method is adopted to eliminate redundant information between multi-domain features, and construct a health index (HI) based on convolutional auto-encoder (CAE) network. Thirdly, a TCN-based performance degradation trend prediction model is constructed, and direct multi-step prediction is used to predict the performance degradation trend of the monitored object. On this basis, the validity of the proposed method is verified using the bearing public data, and it is successfully applied to performance degradation trend prediction of rolling contact fatigue specimen. The results show that the feature set can be reduced from 14 dimensions to 4 dimensions by using KPCA, while 98.33% of the information of the original feature set is retained. Furthermore, the method of constructing HI based on CAE network is effective. The change process of the HI constructed truly reflects the performance degradation process of the rolling contact fatigue specimen. Compared with the two commonly used HI construction methods, auto-encoding (AE) network and gaussian mixture model (GMM), this method has obvious advantages. At the same time, the prediction model based on TCN can accurately predict the performance degradation of the rolling contact fatigue specimen with the root mean square error 0.0146 and the mean absolute error 0.0105, which has better performance and higher prediction accuracy than the prediction model based on the long short-term memory (LSTM) network and the gated recurrent unit (GRU). This method has general significance and may be extended to the performance degradation prediction of other mechanical equipment/parts.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

Should our planet be visited by an extraterrestrial civilization, the prevailing assumption would undoubtedly be that the extraterrestrial civilization is Type I i.e. its capacity for interstellar travel results from its technological development. This assumption is dangerous for it unnecessarily leads to the Extraterrestrial Tandem Hypothesis (ETH): the belief than an extraterrestrial civilization technologically capable of interstellar travel must also be technologically compatible with the inexorably rapid annihilation of life on Earth. Such a state of things would compromise the planet’s capacity to stage a confident defense should the extraterrestrials prove belligerent. The presumption of Type I extraterrestrials (on the premise of the capacity for interstellar travel alone) is unfounded as extraterrestrials may be Type II i.e. capable of interstellar travel by virtue of natural intrinsic or extrinsic factors. This paper advances, most importantly, that the fundamental policy of first contact should be the employment of various strategies toward the evaluation of the technological capacity of visiting extraterrestrials. This evaluation must be particularly devoted to the detection of Type II extraterrestrials masquerading as Type I (using concealment and Wizard of Oz strategies). Integral to this detection are the concepts of the precedence relation and The Extraterrestrial Exclusion Principle (EEP). A precedence relation is a qualitative relation expressing the relative difficulty of producing a technological action. The Extraterrestrial Exclusion Principle states that a Type I extraterrestrial life form is excluded from certain actions. Such actions are lower in precedence than interstellar travel and may be described as in violation of the EEP or EEP forbidden. EEP actions reveal extraterrestrials to be Type II. As an example, the value of the Hawking Warning is subjected to EEP analysis. Furthermore, a hypothetical conundrum in linguistics termed the Kryptonian Linguistic Paradox (KLP) is discussed as a case of an EEP forbidden act. Finally, the paper explores the limitations of the stated fundamental policy of first contact.

In order to reduce the large damage caused by train derailment, protective facilities of various shapes and conditions can be installed on railroad tracks. These protective facilities are referred to as derailment containment provisions (DCPs) and three different types are used worldwide. However, there are no clear standards for DCPs design such as installation location, size, and design load, and performance verification of DCPs installed in the actual railway field is not sufficiently performed. In this paper, the functionality of DCPs is analyzed through the full-scale derailment test. In order to propose a method for estimating the collision load acting on the DCP type I after derailment, the experimental results and simulation results are compared. The function of DCP type I according to the change of the vehicle's center of gravity is identified through comparative analysis of the post derailment behavior.

In cross-country skiing the time difference between a race winner and the person coming second is typically very small. Since much of the energy is spent on overcoming resistive forces, a relatively small reduction of these can have a significant impact on the results. The resistive forces come partly from the friction in the tribological interface, between the ski and the snow, and as with many tribological applications the characterisation of its origin, plays an important role in determining the frictional properties. Also in cross-country ski friction, there are several scales impacting the frictional performance, with the major contributors being the ski-camber profile and ski-base structure. Macro-scale measurements of the ski's camber profile under load, are often used to determine how adequate the ski is for a specific condition. The characteristic properties usually obtained are, the force required to collapse the ski to a certain camber height, the topography of the kick-wax zone, and by simple means a determined lengths of the frictional interface, i.e., the apparent contact length. To this date, there are some mathematical models, but there is no robust way of determining the macro-scale contact properties between a cross-country ski and a counter surface using simulations. In the present paper an Artificial neural networks (ANN) is trained to predict the ski-camber profile for various loads placed at different positions, and a well established deterministic approach is used to simulate the contact between the ANN-predicted ski-camber profile and a linearly elastic body with a flat surface, representing the snow. The results suggest that this method is feasible for the determination of the apparent contact characteristics of different skis. Moreover, we show that the apparent contact area does not linearly depend on the load, and that the elastic properties of the counter surface also has a large impact on the apparent contact area and the average apparent contact pressure.

Skin involvement is an overlooked aspect in the management of paediatric patients with type 1 diabetes. A comprehensive search of published literature using the PubMed database was carried out using the following key terms: “children”, “pediatric/paediatric patients”, “skin”, “skin disorders”, “type 1 diabetes”. Dermatological side effects are frequently observed among diabetic children and adolescents. Insulin-induced lipodystrophies and allergic contact dermatitis caused by insulin pumps or glycaemic sensors are the most common skin reactions in these patients. Furthermore, several diabetes-associated skin diseases such as necrobiosis lipoidica, granuloma annulare, vitiligo, and bullosis diabeticorum may already be present in paediatric age. Paediatric diabetes specialists should pay attention to their patients’ skin so as to recognize these disorders, identify the potential causes, and choose the most suitable treatment. Finally, the evaluation of skin concentrations of advanced glycation end-products using non-invasive diagnostic techniques may be used to assess the risk of chronic complications of diabetes as early as adolescence.

For the treatment of cancer and other diseases, therapeutic targeting of non-coding RNAs (ncRNAs) such as microRNAs (miRNAs) and long non-coding RNAs (lncRNAs) is an attractive approach. RNA-based therapeutics have been extensively researched over the past decade, with antisense oligonucleotides and small interfering RNAs being the most commonly used. Some of these have even gained FDA approval. However, the results of trials have been mixed, with some studies reporting strong effects while others have shown limited effectiveness or toxicity. Alternative treatments, such as antimiRNAs, are currently in clinical trials. There is growing interest in the use of lncRNA-based therapies. This Perspective discusses the main challenges of ncRNA therapeutics, including specificity, delivery and tolerability. It also highlights emerging approaches that aim to improve their success.

The iron roughneck is an automated equipment utilized for the connection and removal of drilling tools. This paper presents the design of an integrated iron roughneck, providing a detailed introduction to its clamp body structure, along with an analysis of its structural characteristics and performance requirements. The study delves into the integration mode and working characteristics of the clamping mechanism and spin buckle mechanism for the integrated upper clamp body structure of the iron roughneck. Additionally, this paper conducts an in-depth theoretical study on the spin buckle mechanism. Firstly, it analyzes the actual working condition of the spin buckle roller from two perspectives: contact theory and rolling friction theory, determining the structural form of the spin buckle roller. Secondly, it investigates the relative displacement between the spin buckle mechanism and the drilling tool, proposing a design method for the floating device mounted on the spin buckle roller and establishing the kinematic equation of the spin buckle roller under the influence of the floating device. Furthermore, the kinematic equations of the spin buckle roller under the influence of the floating device are established. Finally, a dynamics simulation experiment is performed to simulate the working process of the spin buckle mechanism under actual working conditions, analyzing the dynamics and kinematics of the spin buckle mechanism and obtaining the relevant parameter curves of the spin buckle mechanism and drilling tools. Through data comparison and analysis, the correctness of the theoretical analysis results and the rationality of the performance and structure of the spin buckle mechanism are verified.

Rotational jumps are crucial techniques in sports competitions. Estimating ground reaction forces (GRFs), one of the components constituting jumps, through a biomechanical model-based approach enables analysis even in environments where force plates or machine learning training data cannot be utilized. In this study, rotational jump movements involving twists on land were measured using inertial measurement units (IMUs) and estimated GRFs and body loads using a 3D forward dynamics model. Our estimation method, based on forward dynamics and optimization calculations, generated and optimized body movements using cost functions defined by motion measurements and internal body loads. To reduce the influence of the dynamic acceleration in the optimization calculation, the 3D orientation using sensor fusion composed of acceleration and angular velocity data obtained from IMUs and an extended Kalman filter was estimated. As a result, by generating movements based on the cost function, it was possible to calculate biomechanically valid GRFs while following the measured movements even if not all joints are covered by IMUs. This estimation method allows for 3D motion analysis independent of measurement conditions or training data.

We consider a stationary inclusion in a real Hilbert space X, governed by a set of constraints K, a nonlinear operator A and an element f∈X. Under appropriate assumptions on the data the inclusion has a unique solution, denoted by u. We state and prove a covergence criterion, i.e., we provide necessary and sufficient conditions on a sequence {un}⊂X which guarantee its convergence to the solution u. We then present several applications which provide the continuous dependence of the solution with respect to the data K, A and f, on one hand, and the convergence of an associate penalty problem, on the other hand. We use these abstract results in the study of a frictional contact problem with elastic materials which, in a weak formulation, leads to a stationary inclusion for the deformation field. Finally, we apply the abstract penalty method in the anlysis of two nonlinear elastic constitutive laws.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

To address the problem of limited fault diagnosis accuracy in oil-immersed on-load tap changers (OLTC), this paper introduces a novel fault diagnosis method that combines the analysis of mechanical vibration signals and high-frequency current signals. The proposed approach aims to enhance the accuracy of fault diagnosis. To begin, an experimental platform is constructed to simulate the OLTC contact. Mechanical vibration signals and high-frequency current signals are collected from the testing platform under various operating states. These signals are then subjected to wavelet packet transform for denoising, followed by correlation analysis to capture the relationship between signals in different states. Based on these preliminary steps, the features of the signals are extracted and analyzed using ensemble empirical mode decomposition and the Hilbert-Huang transform. Subsequently, a support vector machine (SVM) is employed to analyze both the mechanical vibration signal and high-frequency current signal, enabling the classification of the OLTC contact state. The results demonstrate that the combination of characteristic analysis of mechanical vibration signals and high-frequency current signals provides a more comprehensive reflection of the actual OLTC contact state under different conditions. Through the SVM classification, the error between the predicted values and real values of the two types of signals remains below 10%, validating the efficiency and feasibility of the proposed method for fault diagnosis of OLTC contacts. These research findings serve as a reliable foundation for the diagnosis of operational states of on-site oil-immersed on-load tap changers, offering valuable insights for practical applications.

Different contact materials along with optimization of the deposition techniques expand the possibilities to obtain high performance room temperature CdTe-based X/γ-ray detectors. The heterostructures with ohmic (MoOx) and Schottky (MoOx, TiOx, TiN, and In) contacts, created by DC reactive magnetron sputtering and vacuum thermal evaporation, as well as In/CdTe/Au diodes with a p-n junction, formed by laser-induced doping, were developed and investigated. Depending on the pre-treatment of the surface of semi-insulating p-CdTe crystals, deposition of a MoOx film formed an ohmic or Schottky contact. Based on the calculations and IV characteristics of the fabricated Mo-MoOx/р-CdTe/MoOx-Mo, In/CdTe/MoOx-Mo, Ti-TiOx/р-CdTe/MoOx-Mo, and Ti-TiN/р-CdTe/MoOx-Mo Schottky-diode detectors, the current transport processes were described in the models of the carrier generation-recombination within the space-charge region (SCR) at low bias voltages, and space-charge limited current at higher voltages, respectively. The energies of generation–recombination centers, density of trapping centers, and carrier lifetimes were determined. A sharp increase in the reverse current in the Mo-MoOx/р-CdTe/MoOx-Mo, Ti-TiOx/р-CdTe/MoOx-Mo, and Ti-TiN/р-CdTe/MoOx-Mo heterostructures at high bias was discussed in frames of the Poole–Frenkel emission model. Nanosecond laser irradiation of the In electrode, pre-deposited on the p-CdTe crystals, resulted in an increase in the voltage range, corresponding to the carrier generation-recombination in the SCR, in the IV characteristics of the In/CdTe/Au diodes. Such In/CdTe/Au p-n junction diodes demonstrated high energy resolutions (7%@59.5 keV, 4%@122 keV, and 1.6%@662 keV).

In this paper we analyse spatial variation in Japanese dialectal lexicon by assembling a set of methodologies using theories in variationist linguistics and GIScience, and tools used in historical GIS. Based on historical dialect atlas data, we calculate a linguistic distance matrix across survey localities. The linguistic variation expressed through this distance is contrasted with several measurements, based on spatial distance, utilised to estimate language contact potential across Japan, historically and at present. Further, administrative boundaries are tested for their separation effect. Measuring aggregate association within linguistic variation can contrast previous notions of dialect area formation by detecting continua. Depending on local geographies in spatial subsets, great circle distance, travel distance and travel times explain a similar proportion of the variance in linguistic distance despite the limitations of the latter two. While they explain the majority, two further measurements estimating contact have lower explanatory power: least cost paths modelling contact before the industrial revolution, based on DEM and seafaring, and a linguistic influence index based on settlement hierarchy. Historical domain boundaries and present day prefecture boundaries are found to have a statistically significant effect on dialectal variation. However, the interplay of boundaries and distance is yet to be identified. We claim that a similar methodology can address spatial variation in other digital humanities, given a similar spatial and attribute granularity.

The creation of hydrophobic, antifreeze and self-cleaning coatings is currently being pursued by many industrial sectors. The potential applications include the production of liquid and gas separators and filters, new materials, optical and microelectronic devices, and textiles and clothing. These coatings will also have wide application in the construction and automobile industries, shipping, and energy and agricultural sectors. The article proposes a simple approach to the creation of superhydrophobic and antifreeze coatings, by applying powder from multi-walled carbon nanotubes (MW-CNTs) to the sample surface. This method enables combination of the necessary factors: low surface energy, micro–nano-roughness and hierarchical multi-scale. The authors investigated the dependence of the wetting angle of such a surface on the time, type and degree of functionalization. The electrophysical properties of modified MW-CNTs were studied over wide frequency and temperature ranges. This method of obtaining hydrophobic coatings differs from currently available methods in that it is simpler to prepare, is of lower cost and has less environmental impact. The proposed approach can be used to create superhydrophobic coatings that have the additional function of removing static charge and therefore reducing surface heating, and which can be used in the field of energetics for protection against the freezing of wind turbine blades and aircraft surfaces.

Non-compliant (NC) structures are often encountered in building construction in developing countries. This is a condition whereby erected buildings do not follow regulatory standards, especially in the provision of reinforcements. Therefore, under an earthquake load, the structures do not have sufficient resistance against such load. The structural elements of the building, which often have NC conditions, are the beam-column joints because they do not contain adequate shear reinforcements due to installation difficulty. This study aims to determine the structural performance of the reinforced concrete (RC) frame, which has a reinforcement deficiency in the beam-column joints. Numerical simulation was conducted on the Kakaletsis structure model by modifying the reinforcement details at the joints to represent the NC conditions. The non-linear modeling and analysis of the structural model were carried out using ATENA software. The analysis showed that the reduction in shear reinforcements in the NC model joint caused a decrease in load-carrying capacity by about 26.04%. A shift was also observed in the collapse pattern, i.e., from the beam to the end of the column, causing global failure and reducing the undamaged but increasing more severely damaged condition. This showed that the NC structure, due to the non-conformance of reinforcement, significantly reduced the structure's performance.

An exhaustive list of thirteen instances of reports confirming experimentally the relativistic Doppler relation, are examined. For those involving longitudinal Doppler, the non-relativistic relation is seen to be confirmed, within the reported experimental accuracies, to the same degree as the standard relativistic relation. Higher values of the speed of the emitter would be required to examine further the claimed confirmations. For those reports involving saturation spectroscopy, there is much confusion over the appropriate Doppler relation to be used, together with some serious analytical flaws. For the two cases that involve transverse Doppler, there are seen to be either serious faults in the theoretical part, or intrusion from the first order effect. Therefore, the reported conclusions - that the results for the experiments confirm the relativistic SR relation - cannot be justified by any of the experimental works.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{F}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We show that the public, secret and channel keys become indistinguishable to the eavesdropper under matrix multiplication. Remarkably, for achieving a 512-bit security level, the public key is 1024 bits and the private key is 768 bits, making them the smallest keys among post-quantum key exchange algorithms. Also, we discuss how to achieve key authentication, interdomain certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{Z}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We claim that the unique eavesdropper's opportunity to get the secret/private key is by means of an exhaustive search which is equivalent to the unsorted database search problem. Furthermore, we show that the secret/private keys become indistinguishable to the eavesdropper. Remarkably, to achieve a 512-bit security level, the keys (public/private) are of the same size when matrix multiplication is done over a reduced 8-bit size modulo. Also, we discuss how to achieve key certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

This article develops duality principles and numerical results for a large class of non-convex variational models. The main results are based on fundamental tools of convex analysis, duality theory and calculus of variations. More specifically the approach is established for a class of non-convex functionals similar as those found in some models in phase transition. Finally, in some sections we present concerning numerical examples and the respective softwares.

Let $\mathbb{K}$ be a non-Archimedean (complete) valued field satisfying \begin{align*} \left|\sum_{j=1}^{n}\lambda_j^2\right|=\max_{1\leq j \leq n}|\lambda_j|^2, \quad \forall \lambda_j \in \mathbb{K}, 1\leq j \leq n, \forall n \in \mathbb{N}. \end{align*} For $d\in \mathbb{N}$, let $\mathbb{K}^d$ be the standard $d$-dimensional non-Archimedean Hilbert space. Let $m \in \mathbb{N}$ and $\text{Sym}^m(\mathbb{K}^d)$ be the non-Archimedean Hilbert space of symmetric m-tensors. We prove the following result. If $\{\tau_j\}_{j=1}^n$ is a collection in $\mathbb{K}^d$ satisfying $\langle \tau_j, \tau_j\rangle =1$ for all $1\leq j \leq n$ and the operator $\text{Sym}^m(\mathbb{K}^d)\ni x \mapsto \sum_{j=1}^n\langle x, \tau_j^{\otimes m}\rangle \tau_j^{\otimes m} \in \text{Sym}^m(\mathbb{K}^d)$ is diagonalizable, then \begin{align}\label{WELCHNONABSTRACT} \max_{1\leq j,k \leq n, j \neq k}\{|n|, |\langle \tau_j, \tau_k\rangle|^{2m} \}\geq \frac{|n|^2}{\left|{d+m-1 \choose m}\right| }. \end{align} We call Inequality (\ref{WELCHNONABSTRACT}) as the non-Archimedean version of Welch bounds obtained by Welch [\textit{IEEE Transactions on Information Theory, 1974}]. We formulate non-Archimedean Zauner conjecture.

Nonionizing millimeter-waves (MMW) interact with cells in a variety of ways. Here the inhibited cell division effect was investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm2 safety standards. Irradiation using a power density of about 1.0 mW/cm2 , SAR over 5-6 hours on 50 cells/μl samples of Saccharomyces cerevisiae model organism resulted in 62% growth rate reduction compared to the control (sham). The effect was specific for 85-105 GHz range, and was energy and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deleted cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause permanent genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm2) and compared to that of a compact waveguide (17.17 mW/cm2) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. We have shown that non-thermal MMW radiation has potential for future use in treatment of yeast related diseases and other targeted biomedical outcomes.

Nonionizing millimeter-waves (MMW) are reported to interact with cells in a variety of ways. Possible mechanisms of the inhibited cell division effect were investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm² safety standards. ~1.0 mW/cm² exposure over 5-6 hours treatment on 50 cells/μl samples of Saccharomyces cerevisiae model organism, resulted in 62% growth rate reduction compared to control (sham). The effect was specific for 85-105 GHz range and energy dose and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deletion cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm²) and compared to that of a compact waveguide (17.17 mW/cm²) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. Combinations of MMW mediated Structure Resonant Energy Transfer (SRET), membrane modulations eliciting signaling effects, and energetic resonance with biomolecules were indicated to be responsible for the observations reported. Our results provide novel mechanistic insights enabling innovative applications of nonionizing radiation procedures for eliciting targeted biomedical outcomes.

Addressing non-unions involves stabilizing the affected area through osteosynthesis and improving bone biology using bone grafts. However, there is no consensus on the optimal treatment method. This study aims to compare outcomes of non-union revision using conventional treatment methods (metal hardware ± graft) versus osteosynthesis with the human, allogeneic cortical bone screw (Shark Screw®). Thirty-four patients underwent conventional treatment, while 28 cases received Shark Screws®. Patient demographics, bone healing, time to bone healing, and complications were assessed. Results revealed a healing rate of 96.4% for the Shark Screw® group, compared to 82.3% for the conventionally treated group. The Shark Screw® group exhibited a tendency for faster bone healing (9.4±3.2 vs. 12.9±8.5 weeks, p=0.05061). Hardware irritations led to six metal removals in the conventional group versus two in the Shark Screw® group. The Shark Screw® emerges as a promising option for personalized non-union treatment in the foot, ankle, and select lower leg cases, facilitating effective osteosynthesis and grafting within a single construct, promoting high union rates, low complications, and a rapid healing process.

Total ankle replacement (TAR) implants are an effective option to restore the range of motion of the ankle joint for arthritic patients. An effective tool for analyzing these implants’ mechanical performance and longevity in-silico is finite element analysis (FEA). ABAQUS FEA was used to statically analyze the von Mises stress and contact pressure on the articulating surface of the bearing component in two newly installed fixed-bearing total ankle replacement implants (the Wright Medical INBONE II and the Exactech Vantage). This ultra-high molecular weight polyethylene (UHMWPE) bearing commonly fails and is the cause for surgeon revisions. Six different FEA models for various gait percentages during stance (10%-60%) were created. They varied in magnitude of the compressive load and the ankle dorsiflexion/plantarflexion angle. The results indicated that the von Mises stress and contact pressure distributions increased as compressive load increased, and the largest magnitudes occurred at high dorsiflexion angles (15-30°). High magnitudes occurred in regions where the thickness of the bearing was the least. Additionally, high contact pressures were examined in areas near the talar component's edge or at the bearing's edges. To the author’s knowledge, this is the first study available to the research community that analyzes the Vantage implant with FEA. This study lays an essential foundation for future researchers in presenting a thorough literature review of TAR and methods for a simple FEA model setup. This study provides valuable information that can be beneficial to medical company designers and orthopedic surgeons in understanding the stress response and contact pressure of TAR implants during use.

Predicting ground reaction forces (GRFs) and ground reaction moments (GRMs) through a biomechanical model-based approach offers advantages for biomechanical analysis, particularly in situations where the application of a statistical model is limited by insufficient training data. However, the current prediction method is unsuitable for clinical applications due to its long computational time. The present study developed a new optical motion capture (OMC)-based method to predict GRFs, GRMs, and joint torques. The proposed approach performed the estimation process by distributing external forces, as determined by the equation of motion, between the left and right feet based on foot deformations, thereby predicting the GRFs and GRMs without relying on machine learning or optimization techniques. We investigated the prediction accuracy during walking by comparing a conventional analysis using a force plate with the OMC results. The comparison revealed excellent or strong correlations between the prediction and measurement for all GRFs, GRMs, and lower limb joint torques. The proposed method, which provides practical estimation with low computational cost, facilitates efficient biomechanical analysis and rapid feedback of analysis results, thereby increasing its applicability for kinetics estimation in clinical settings.

A small but growing body of literature suggests that outdoor experiences during childhood affect environment-related behaviors in adulthood. However, research on the magnitude of the effect (effect size) of outdoor experience on learners’ behaviors remains scarce. In this study, we explore the extent to which outdoor experiences associate with environmentally responsible behaviors. Our sample consisted of 143 ninth- and tenth-grade students living on a Greek island. The data were collected using a properly adjusted environmental literacy instrument. Two different methodological pathways, i.e., a quasi-experimental approach and correlation analysis, were used to analyse the data. A tentative variable representing the frequency and intensity of students’ experiential contact with nature was found to be the strongest available predictor of their self-reported pro-environmental behaviors. The findings of this study support the significance of outdoor, experiential learning during childhood in shaping individuals’ environmental behaviors.

Four leather substrates from different animals were treated by dispersions containing hydrophilic composite silica-hyperbranched poly(ethylene imine) xerogels. Antimicrobial activity was introduced by incorporating silver nanoparticles and /or benzalkonium chloride. The gel precursor solutions were also infused before gelation to titanium oxide powders typically employed for induction of self-cleaning properties. The dispersions from these biomimetically premade xerogels integrate environmentally friendly materials with short coating times. Scanning electron microscopy (SEM) provided information on the powder distribution onto the leathers. Substrate and coating composition were estimated by infrared spectroscopy (IR) and ener-gy-dispersive X-ray spectroscopy (EDS). Surface hydrophilicity and water permeability were assessed by water-contact angle experiments. The diffusion of the leather's initial components and xerogel additives into the water were measured by Ultraviolet-Visible (UV-Vis) spectroscopy. Protection against GRAM- bacteria was tested for Escherichia coli, Pseudomonas aeruginosa, and Klebsiella Pneumoniae against GRAM+ bacteria for Staphylococcus aureus, and Enterococcus faecalis and against fungi for Candida albicans. Antibiofilm capacity experiments were performed against Staphylococcus aureus, Klebsiella Pneumoniae, Enterococcus faecalis, and Candida albicans. The application of xerogel dispersions proved an adequate and economically feasible alternative to the direct gel formation into the substrate’s pores for the preparation of leathers intended for medical uses

Artificial groundwater recharge is commonly used for drinking water supply. The resulting water quality is highly dependent on the raw water quality. In many cases, pre-treatment is required. Pre-treatment improves the drinking water quality, although how and to what extent it affects the subsequent pond water quality and infiltration process, is still unknown. We evaluated two treatment systems by applying different pre-treatment methods for raw water from a eutrophic and temperate lake. An artificial recharge pond was divided into two parts, where one received raw water, only filtered through a micro-screen with 500 µm pores (control treatment), while the other part received pre-treated lake water using chemical flocculation with polyaluminium chloride (PACl) combined with sand filtration, i.e. continuous contact filtration (contact filter treatment). Water quality such as cyanobacterial biomass, microcystin-LR as well as organic matter and nutrients were measured in both treatment processes. We found cyanobacterial biomass and microcystin-LR level after the contact filter treatment was significantly different from the control treatment and also significantly different in the pond water. In addition, with contact filter treatment, total phosphorus (TP) and organic matter removal were significantly improved in the end water, TP was reduced by 96 % (< 20 µg/L) and the total organic carbon (TOC) was reduced by 66 % instead of 55 % (TOC content around 2.1 mg/L instead of 3.0 mg/L). This full-scale onsite experiment demonstrated effective pre-treatment would benefit a more stable water quality system, with less variance and lower cyanotoxin risk. In a broader drinking water management perspective, the presented method is promising to reduce cyanotoxin risk, as well as TP and TOC, which are all predicted to increase with global warming and extreme weather.