This paper shows the development of a numerical analysis model, which enables the calculation of the cargo transport capacity of a vehicle that circulates through a vacuum tube at high speed, whose effectiveness in transport is analyzed. The simulated transportation system is based on vehicles moving in vacuum tubes at high speed, a concept commonly known as Hyperloop, but assuming the vehicles for cargo containers. For the specific vehicle proposed, which does not include a compressor and levitates on magnets, the system formed by the vehicle and the vacuum tube has been conceptually developed, establishing the corresponding mathematical relationships that define its behavior. To properly model the performance of this transport system, it has been necessary to establish the relationships between the design variables and the associated constraints, such as the Kantrowitz limit, aerodynamics, transport, energy consumption, etc. Once the model was built and validated, it was used to analyze the effects of the variation of the number of containers, the operating speed and the tube length, considering the total and specific consumption of energy. Once the most efficient configuration was found regarding energy consumption and transport effectiveness, the complete system was calculated. The results obtained constitute a first approximation for the pre-design of this transport system and the built model allows different alternatives to be compared according to the design variables.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

This study aims to develop a performance evaluation system that can facilitate performance evaluation at region, hospital, and department levels to enable better cost management for sustainable development. A multi-level system of performance evaluation informs a hierarchical assessment of cost management from regions to hospitals to departments using diagnosis-related group (DRGs). Various metrics are developed employing the variances between targets and actuals where targets are determined from two perspectives: benchmarking using external regional prices and change management using internal data. Targets for the latter are statistically based and specifically incorporate variability. The model is applied to two hospitals, twenty departments, nine DRGs and 1071 inpatients. The analyses indicate that the approach can provide a practical evaluation tool that allows for particular characteristics at multiple levels. The system provides macro-micro and external-internal perspectives in performance, enabling high-level variances to be decomposed thereby identifying sources of performance variability and financial impact.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

High Vacuum Flat Plate Collectors (HVFPCs) are the only type of Flat Plate Thermal Collectors capable of producing thermal energy for middle-temperature applications (until 180 °C). As the trend of research plans to develop new Selective Solar Absorbers to extend the range of HVFPC application until 250 °C, it is necessary to correctly evaluate the collector efficiency up to such temperature to predict the energy production accurately. We propose an efficiency model for these collectors based on the selective absorber optical properties. The proposed efficiency model explicitly includes the radiative heat exchange with the ambient, which is the main source of thermal losses for evacuated collectors at high temperatures. It also decouples the radiative losses that depend on the optical properties of the absorber adopted from the other thermal losses due to HVFPC architecture. The model has been validated by applying it to MT-Power HVFPC manufactured by TVP-Solar, and it has been used to predict the efficiency and energy production of HVFPC equipped with new, optimized selective solar absorbers developed in recent years.

To determine promethazine (PMZ) and its metabolites promethazine sulfoxide (PMZSO) and monodesmethyl-promethazine (Nor1PMZ) in swine muscle, fat, kidney, and liver, a sample preparation and high-performance liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis method were established and validated. The sample was extracted with 0.1% formic acid-acetonitrile, and the extract was purified with acetonitrile-saturated n-hexane. After concentration by rotary evaporation, the extract was re-dissolved in 0.1% formic acid-water and acetonitrile (80:20, v/v). The HPLC-MS/MS column used was a Waters Symmetry C18 (100 mm × 2.1 mm i.d., 3.5 μm), with 0.1% formic acid-water and acetonitrile as the mobile phase, and the target compounds were determined by positive ion scan and multiple reaction monitoring. PMZ and Nor1PMZ were quantified with deuterated promethazine (PMZ-d6) as the internal standard, while PMZSO was quantified by external standard method. The limits of detection (LOD) and limits of quantification (LOQ) of PMZ and PMZSO in muscle, liver, and kidney spiked samples were 0.05 μg/kg and 0.1 μg/kg, respectively, while those of Nor1PMZ were 0.1 μg/kg and 0.5 μg/kg, respectively. The LOD and LOQ of analytes in fat spiked sample were 0.05 μg/kg and 0.1 μg/kg, respectively. The sensitivity of this method reaches or exceeds its presented in previous reports. The analytes PMZ and PMZSO showed good linearity within the range of 0.1 μg/kg to 50 μg/kg, while Nor1PMZ showed good linearity within the range of 0.5 μg/kg to 50 μg/kg, with correlation coefficients (r) greater than 0.99. The recoveries of the target compounds in the sam-ples were between 81.73% and 107.17%, and the precision ranged from 1.78% to 10.47%. This study developed for the first time an HPLC-MS/MS method for the determination of PMZ and its metabolites PMZSO and Nor1PMZ in four swine edible tissues, comprehensively covered target tissues of monitoring object, which is applicable for monitoring veterinary drug residues in ani-mal-derived foods and ensuring food safety.

Lipophilicity can be measured with different methods, such as Shake-Flask or liquid chromatography. HPLC presents the advantage of overcoming solubility issues and therefore extending the range of lipophilicity to high values. A specific HPLC method, called ELogD, had been developed 20 years ago on a C₁₆-amide stationary phase, enhancing hydrophobic and hydrogen bond interactions to mimic octanol-water partition. The emergence of novel stationary phases added to the need for a less complex mobile phase has led to the development of a new HPLC assay called alphaLogD, applicable to neutral and basic compounds at pH 7.4, that combines superficially porous particles, a high number of equilibriums between solutes and stationary phase, and results in a lower number of isocratic methods to determine the logk’_w at a higher throughput. Statistical studies have been run to successfully evaluate the alphaLogD method compared to the Shake-Flask method and to allow this lipophilicity measurement into the so-called Beyond-Rule-of-5-molecules space.

Predictive simulation of concurrent debris flow using only pre-disaster information has proven to be difficult as a result of problems in predicting the location of debris-flow initiation (i.e., slope failure). However, because catchment topography has concave characteristics, with all channels in a catchment joining each other as they flow downstream, it is possible to predict damage to downstream area using relatively inaccurate initiation points. Based on this, this paper presents methodologies employing debris-flow initiation points generated randomly using statistical slope failure prediction. A many-case simulation across numerous initiation points was performed to quantify the effect of slope-failure location in terms of deviations in the predicted water level and terrain deformation. It was found that the relative standard deviation diminished as the points approached the downstream area, indicating a location-based predictability effect.

As time progresses and technology improves, biological data sets are continuously increasing in size. New methods and new implementations of existing methods are needed to keep pace with this increase. In this paper, we present a high performance computing(HPC)-capable implementation of Iterative Random Forest (iRF). This new implementation enables the explainable-AI eQTL analysis of SNP sets with over a million SNPs. Using this implementation we also present a new method, iRF Leave One Out Prediction (iRF-LOOP), for the creation of Predictive Expression Networks on the order of 40,000 genes or more. We compare the new implementation of iRF with the previous R version and analyze its time to completion on two of the world's fastest supercomputers Summit and Titan. We also show iRF-LOOP's ability to capture biologically significant results when creating Predictive Expression Networks. This new implementation of iRF will enable the analysis of biological data sets at scales that were previously not possible.

In the case of long-stator linear drive, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signals transmitted from maglev vehicle can’t meet the need of the real-time propulsion control in the on-ground inverter power substations. In this paper the design of the propulsion inverter control system with a position estimator for driving long-stator synchronous motor in high speed maglev train is proposed. The experiments have been carried out at the 150m long guideway in O-song test track. To investigate the performance of the position estimator, the propulsion control system with and without the position estimator are compared. The result confirms that the proposed strategy can meet the dynamic property need of propulsion inverter control system for driving long-stator linear synchronous motors

Developing high performance HVAC system using natural refrigerants including carbon dioxide (CO₂) has been important in respect of environmental preservation and associated technologies. Thus studies to optimize the HVAC (heating ventilation air conditioner) system using natural refrigerants through clarifying the cycle performance characteristics are necessary. The CO₂ heat pump system using air and water sources was consisted to examine its performance characteristics, and by varying conditions of several factors that affect or characterize the system performance like the amount of refrigerant charge, EEV (electronic expansion valve) opening, and internal heat exchanger under cooling mode. The performance characteristics of CO₂ heat pump system were tested by using an air enthalpy calorimeter. In the case of the CO₂ heat pump system without internal heat exchanger, the opening of #3 EEV and #4 EEV was 60% and refrigerant charge amount was 5,600g. However, in the case of that with internal heat exchanger, the best performance was obtained when the opening of #2 EEV is 20%. From the present studies, it was observed that the performance variation and operational characteristics of the CO₂ heat pump system were affected by design factors like refrigerant charge amount, EEV opening, and internal heat exchanger and thereby, the configuration on an optimal operation conditions of the system was enabled.

Solid spent nuclear fuel from nuclear power plants has 3.4% fission products (80-160amu), contributing to over 99.8% radioactivity. On the other hand, liquid high-level radioactive waste (HLRW) from spent fuel reprocessing has 98.9% bulk elements (0-60amu) with 0.1% radioactivity. A separation mechanism on the mass categories as groups presents unique opportunities in managing HLRW for the long term with a considerable cost reduction. This paper proposes a thermal plasma-based separation system incorporating atmospheric pressure plasma torches for HLRW mass separation into low-resolution mass groups. Several engineering issues, such as waste preparation, waste injection into the plasma and waste collecting after mass separation, need to be addressed. Using COMSOL Multiphysics simulation, the generic system can be studied using noble gas mass separation and further analyze the mass filter capabilities. This paper provides the history of plasma-based mass separation. Functional modelling of a thermal plasma mass separation system is proposed under atmospheric pressure. Finally, aspects of mass separation simulation using noble gas Argon and Helium inside the plasma mass separation system were studied in COMSOL Multiphysics.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

Background: Primary central nervous system lymphomas (PCNSLs) are sensitive to chemotherapy. Standard treatment is high-dose methotrexate (MTX)-based chemotherapy. There are no reports of successful treatment of acute uric acid nephropathy with rasburicase after MTX administration in PCNSL. Case presentation: A 54-year-old man with a history of gout presented with character change and memory loss. MRI showed a large, enhancing mass spanning the bilateral frontal lobes and right temporal lobe. After endoscopic biopsy, MTX, procarbazine and vincristine (MPV) regimen was initiated for treatment of PCNSL. After initiation of chemotherapy, the patient suffered from a gout attack and blood examination revealed acute renal failure (ARF) and hyperuricemia. The considered causes of ARF included MTX toxicity and acute urid acid nephropathy. Since a good response to chemotherapy was observed, the latter was assumed. After improvement of renal function, MTX was resumed, initiating rasburicase for control of hyperuricemia. A complete response was obtained after induction chemotherapy. Hyperuricemia was controlled with rasburicase and renal function was preserved. Conclusions: Acute uric acid nephropathy should be considered when ARF occurs after initiation of MTX in PCNSL. For newly diagnosed PCNSL patients with large tumors or hyperuricemia, upfront usage of rasburicase should be considered to prevent it.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Lattice and code cryptography can replace existing schemes such as Elliptic Curve Cryptography because of their resistance to quantum computers. In support of public key infrastructures, the distribution, validation and storage of the cryptographic keys is then more complex to handle longer keys. This paper describes practical ways to generate keys from physical unclonable functions, for both lattice and code based cryptography. Handshakes between client devices containing the PUFs and a server are used to select sets of addressable positions in the PUFs, from which streams of bits called seeds are generated on demand. The public and private cryptographic key pairs are computed from these seeds together with additional streams of random numbers. The method allows the server to independently validate the public key generated by the PUF, and act as a certificate authority in the network. Technologies such as High performance computing, and graphic processing units can further enhance security by preventing attackers to make this independent validation when only equipped with less powerful computers.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

The morphology of virgin reactor powder (RP) of high-density polyethylene HDPE with MW = 160,000 g/mol was investigated with the help of DSC, SEM, SAXS and WAXS methods. The morphological SEM analysis showed, that the main morphological units of RP are macro- and micro-shish kebab structures with significantly different geometric dimensions, as well as individual lamellae of folded chain crystals. Quantitative analysis of an asymmetric SAXS reflection made it possible to reveal the presence of several periodic morphoses in the RP with long periods from 20 nm to 60 nm and to correlate them with the observed powder morphology. According to the DSC crystallinity data, the thickness of the lamellae in each long period was estimated. Their surface energy was calculated in the framework of the Gibbs-Thompson theory. The presence of regular and irregular folds on the surface of the different shish-kebab lamellae is discussed. The percentage of identified morphoses in the RP was calculated. It has been suggested that the specific structure of HDPE RP is due to the peculiarity of polymer crystallization during suspension synthesis in a quasi-stationary regime, in which local overheating and inhomogeneous distribution of shear stresses in a chemical reactor are possible.

Intercropping systems can flexibly use resources such as sunlight, heat, water, and nutrients in time and space, improve crop yield and land utilization rates, effectively reduce continuous cropping obstacles and the occurrence of diseases and insect pests, and control the growth of weeds. Thus, intercropping is a safe and efficient ecological planting mode. The legume–cereal intercropping system is the most common planting combination. Legume crops fix nitrogen from the atmosphere through their symbiotic nitrogen fixation abilities, and the fixed nitrogen can be transferred to and utilized by cereal crops in various ways. The symbiotic nitrogen fixation efficiency of legume crops was improved by reducing the inhibition of soil nitrogen on nitrogenase activity through competitive absorption of soil nitrogen. However, the effects of nitrogen transformation and distribution in intercropping systems, and microbial community structure characteristics on nitrogen transfer need to be further explored. In this review, ⅰ) we present the transformation and distribution of nitrogen in the legume–cereal intercropping system; ⅱ) we describe the soil microbial community characteristics in intercropping systems; and ⅲ) we discuss the advantages of using modern biological molecular techniques to study soil microorganisms. We conclude that intercropping can increase the diversity of soil microorganisms, and the interaction between different plants has an important impact on the diversity and composition of the bacterial and fungal communities. The extensive application of modern biological molecular techniques in soil microbial research and the great contribution of intercropping systems to sustainable agriculture are particularly emphasized in this review.

Warming of the climate system is unequivocal, and many of the observed changes are unprecedented over five decades to millennia. Globally the atmosphere and ocean is increasingly getting warmer, the amount of ice on the earth is decreasing over the oceans, and the sea level has risen. According to Intergovernmental Panel on Climate Change, the total increasing temperature globally averaged combined land and surface between the average of the 1850-1900 period and the 2003 to 2012 period is 0.78 °C (0.72 to 0.85). But should we prepare for such the relatively small change? The importance is not the mean of the warming but the considerable likelihood of climate change that could trigger extreme natural hazards. The impact and the risk of climate change associated with railway infrastructure have not been fully addressed in the literature due to the difference in local environmental parameters. On the other hand, the current railway network in Malaysia, over the last decade, has been significantly affected by severe weather conditions such as rainfall, lightning, wind and very high temperatures. Our research findings point out the extremes that can lead to asset system failure, degraded operation and ultimately, delays to train services. During the period of flood, the embankment of the track can be swept away and bridge can be demolished, while during drought, the embankment of the track can suffer from soil desiccation and embankment deterioration, high temperature increases the risk of track buckling and high winds can result in vegetation or foreign object incursion on to the infrastructure as well as additional quasi-static burden exerted. This review is of significant importance for planning and design of the newly proposed high speed rail link between Malaysia and Singapore.

Currently, most middleware application developers have two choices when designing or implementing API services: They can either stick with REST or explore the emerging GraphQL technology. Although REST is widely considered the standard method for API development, GraphQL is believed to overcome the main drawbacks of REST, especially data fetching issues. Yet, doubts remain as there are no experimental studies with convincing results to evaluate the performance of the two services. In this paper, we propose a research methodology to evaluate the performance of REST and GraphQL API services, which includes two main contributions. The first contribution is that the performance evaluation of the two services is conducted in the real operation of a massive and intensively accessible management information system. The second contribution is the fair and independent performance evaluation results obtained for both API services. The performance evaluation was studied using basic measures of QoS, including response time, throughput, CPU load, and memory usage. The results show that REST is still faster in response time and throughput, while GraphQL is very efficient in resource utilization, i.e., CPU load and memory utilization. Therefore, GraphQL is the right choice when data requirements change frequently and resource utilization is the most important consideration. REST is used when some data is frequently accessed called by multiple requests.

Abstract：Objective: To compare the effects of fermentation on the chemical composition of Gastrodia Tuder Halimasch Powder, and to provide a basis for the processing, processing and clinical application of this medicinal material. Methods: UHPLC-Q-Orbitrap HRMS was used to identify compound structure by comparing excimer ions, characteristic fragment ions and reference substances, and referring to relevant literature and database search. The main differential components were screened by orthogonal partial least squares-discriminant analysis (OPLS-DA), and the differential components were quantitatively studied by high performance liquid chromatography, and the differences in the types and contents of chemical components before and after fermentation were compared. Results: A total of 77 compounds were identified or preliminarily derived after fermentation, including 21 terpenes, 18 organic acids, 9 flavonoids, 7 nucleosides, 6 amides, 4 amino acids, 2 pyrrolidone derivatives, 2 sterols, 2 alkaloids and 6 others.Through high performance liquid chromatography, it was found that the content of daidzein genistein and ergosterol was significantly increased after fermentation, and a new component ergosterol was produced. Compared with Gastrodia Tuder Halimasch Powder before fermentation, the content of genistin and other components was significantly reduced, and there may be a process of genistin conversion to genistein.Conclusion: The fermentation process will have a certain influence on the types and contents of the chemical components of Gastrodia Tuder Halimasch Powder, and ergosterol, genistein and .daidzein may be the main pharmacodynamic components, which can provide a useful reference for the clinical rational application, quality control and mechanism of action of Gastrodia Tuder Halimasch Powder.

Banking sector is generally taken out of sample while the sustainability performance, and the financial performance are compared with each other. The core aim of this study is to analyze the effect of the declarations made in the cope of sustainability reports on the financial performance in the banking sector. Seven banks were included in the study which were placed at least one time in BIST Sustainability Index in between 2010-2017 years. Environment, human resources, product liability and community involvement were determined as sustainability criteria and return on assets, return on equity and net interest margin were determined as financial performance criteria. Non-Parametric Statistic Tests and Panel Data Analysis were used for analysis and types, and the sizes of banks were selected as dummy variables. As a result, it is found that the declarations of sustainability reports have a significant effect only on return on assets and have no significant effect on return on equity and net interest margin. And also, when we analyzed the relationship of sustainability criteria and return on assets, we found that the declarations about environment and human resources have negative effects on return on assets.

Promoting the use of solar energy resources has always faced the challenges of instability and supply-demand mismatch. The key to solving these issues is to efficiently store and utilize solar energy resources using high-performance heat storage devices. This study designed a high-performance shell-and-tube phase change thermal storage device and established a numerical model using ANSYS software to summarize the device's dynamic melting law. To verify the accuracy of the numerical simulation, a performance testing platform for the phase change thermal storage device was built to investigate the impact of factors such as inlet water temperature, inlet water flow rate, type of heat storage, and initial temperature of the device, and to reveal the change law of the device's performance. The results show that the inlet water temperature has the most significant impact on the device's heat storage and release performance. When the device's heat storage or release is used for heating, changing the inlet water flow rate has a weak and limited effect on the device's performance. However, when the device's heat release is used to provide domestic hot water, increasing the makeup water temperature and reducing the inlet water flow rate can significantly improve the device's effective heat release. Furthermore, based on the experimental validation of the model's correctness, this study further simulated and studied the impact of different factors on the device's heat storage process to optimize its structural design and provide technical references for the device's actual operation and installation. The results show that the placement of fins has a negligible effect on the performance of the heat storage device while reducing the fin spacing and increasing the fin thickness can significantly improve the melting efficiency of the phase change material (PCM). Additionally, the heat storage characteristics of the device are significantly better in the vertical installation mode than in the horizontal installation mode. This study provides theoretical guidance and technical references for the design and use of phase change thermal storage devices.

Sustainability experienced significant global momentum in recent decades. The emergence of the sustainability movement in the Financial Sector was prompted by the increasing global climate change resulting from environmental deterioration. Primarily associated with the Financial Sector, it has increasingly been recognised that Financial Institutions are significant contributors to global climate change, both via direct and indirect means. This has resulted in a heightened emphasis and demand from stakeholders for the implementation of Sustainability Principles on a worldwide scale. This study presents a methodology that utilises the various dimensions of Sustainable Finance through the concept of Triple Bottom Line to determine the factors influencing the Sustainability Performance of Financial Institutions. The suggested approach is grounded and supported by the current body of literature. The study presents a hypothesis to investigate the correlation between factors of Green Finance Practices and Sustainability Performance of Banking Sector. The suggested framework can be utilised by regulatory bodies and individual financial institution of a country to identify the elements that influence the Sustainability Performance of Banking Sector.

This paper aims to demonstrate how the detection of communities for epidemiological networks can be used to reduce the dimensionality of optimal control problems. A range of planted partition stochastic blockmodels are generated, where the underlying communities in the model vary in detectability. A high-performance computing workflow is then used to simulate and estimate reduced model dynamics for the networks, which in turn is used to find optimal control solutions.

This study examines the effect of a corporate citizenship-oriented high performance work system (CC-oriented HPWS) and the interactive influence of CC-oriented HPWS and person-organization fit (PO fit) on creativity at the individual level. Our analysis of field data collected from 303 employees in two branch companies with a two-phase collection method provides empirical support for our theoretical model. The results indicate that high performance work system (HPWS) reflecting corporate citizenship (CC) correlates positively with individual creativity. In addition, the moderating effect of PO fit is significant in the relationship between CC-oriented HPWS and creativity at the individual level. On this basis, this paper discusses the theoretical and practical implications of these findings for future research.

Objective: Lipids are secreted into milk as bilayer-coated structures: milk lipid globules (MLGs). Adipophilin (ADRP) and perilipin 3 (TIP47) are associated with MLGs in human breast milk; however, the role of these proteins in milk lipid secretion is not fully understood. The aim of the study was to investigate levels of ADRP, TIP47 and total lipid content in human breast milk, their mutual correlations and dynamics during lactation. Research Methods & Procedures: Milk samples from 22 healthy lactating women (Caucasian, Central European) were collected at five time points during lactation (1–3, 12–14, 29–30, 88–90 and 178–180 days postpartum). Mass spectrometry-based method was used for quantification of ADRP and TIP47 in the samples. The gravimetric method was used to determine milk total lipid content. Results: We observed distinctive trends in ADRP, TIP47 levels and lipid content in human breast milk during the first 6 months of lactation. We also found a significant association between lipid content and ADRP, lipid content and TIP47, and ADRP and TIP47 concentrations in breast milk at all sampling points. Moreover, we derived an equation for estimating the mean lipid content of milk based on ADRP concentration in human breast milk. Conclusions: A mass spectrometry-based method was developed for quantifying ADRP and TIP47 in human breast milk. Strong mutual correlations were found between ADRP, TIP47 and total lipid content in human breast milk.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

We are introducing a highly efficient 48-channel ultrasound beamforming system ideal for ultrasound endoscopy applications. The system includes a transmitter and a receiver, which allow for low-area, high-resolution imaging acquisition. The transmitter uses a charge redistribution HV (high voltage) scheme to generate three-level pulses that actuate the transducer, implemented with the standard CMOS process for optimal cost and power savings. Meanwhile, the receiver features a sub-array structure and a delay generator that reduces area usage. To achieve high-resolution ultrasound imaging acquisition with low computational power, we developed the Shift Coherence Factor (SCF) algorithm, which is hardware-friendly. This approach delivers a lateral resolution over 20% better than the conventional delay and sum (DAS) algorithm, with a contrast ratio of over 30 dB. The system was implemented in a 180 nm standard CMOS process with an area of 24.98 mm2, power consumption of 8.23 mW per channel, achieving a delay resolution of 8.33 ns, and a low-area implementation of 0.52 mm2 per channel. The system offers high-quality imaging acquisition with minimal additional area and power consumption, which has great potential for 3D imaging or catheterized ultrasound systems.

Lithium batteries and an increasing focus on CO₂ reduction have become an integral part of daily life and business for many people. Boron and boron compounds have been widely studied together in the history and development of lithium batteries. With a broad examination of battery components and systems but a boron-centric approach to raw materials, this review seeks to summarize past and recent studies on the following: which boron compounds are studied in lithium battery, in which parts of lithium batteries, what improvements are offered for battery performance, and what improvement mechanisms can be explained. The uniqueness of boron and its extensive application beyond batteries contextualizes the interesting similarity with studies on batteries. The paper predominantly focuses on lithium-ion batteries (LIBs) but also mentions other lithium batteries. At the end, the article aims to predict prospective trends for future studies that may lead to the successful and extensive use of boron compounds on a commercial scale.

The comprehensive analysis of cross-country skiing races is a pivotal step in establishing effective training objectives and tactical strategies. This study aimed to establish a method for the classifi-cation of sub-techniques and analyzing skiing characteristics during cross-country skiing skating style timed races on snow using high-precision kinematic GNSS devices. The study involved at-taching GNSS devices to the heads of two athletes during skating style timed races on cross-country ski courses. These devices provided precise positional data and recorded vertical and hor-izontal head movements and ground over velocity (VOG). Sub-techniques were classified by de-fining waveform patterns for G2, G3, G4, and G6 based on these data. The validity of classifica-tion was verified by comparing GNSS data with video analysis, a process that yielded classifica-tion accuracies ranging from 94.0% to 99.3% for G2, G3, G4, and G6. Notably, G4 emerged as the fastest technique, with sub-technique selection varying among skiers and being influenced by skiing velocity and course inclination. The study's findings have practical implications for ath-letes and coaches, as they demonstrate that high-precision kinematic GNSS devices can accurate-ly classify sub-techniques and detect skiing characteristics during skate-style cross-country skiing races, thereby providing valuable insights for training and strategy development.

Early weaning of piglets caused excessive concentration of free radicals, which would oxidize and damage the intestinal tract of piglets, resulting in dyspepsia, low growth, diarrhea, microbiota disorders and intestinal infections. This research studied on effect of different levels of taurine in diets on intestinal oxidative damage in early weaned piglets. A total of 48 weaned piglets (6.71 ± 0.73 kg) of 28-day-old crossbred "Duroc × Landrace × Yorkshire" were assigned to 4 groups with 12 replicates per group and 1 pig per replicate: piglets were fed a basal diet with 0.0% (CON), 0.2% taurine (L-Tau), 0.3% taurine (M-Tau), or 0.4% taurine (H-Tau). The animal experiment lasted for 30 days. With the increase of dietary taurine dosage, the activity of antioxidant enzymes including superoxide dismutase（SOD）,glutathione peroxidase（GPX）,catalase（CAT） and peroxidase（POD） were up-regulated (Linear, P < 0.05), the mRNA abundance of antioxidant enzymes including SOD1, SOD2, GPX1 and heme oxygenase-1（HO-1）were up-regulated (P < 0.05), glutathione (GSH) concentrations was up-regulated (Linear, P < 0.05) , nitric oxide (NO), malondialdehyde (MDA) and oxidized glutathione (GSSG) concentrations were down-regulated (Linear, P < 0.05);The villus height (VH) and villus height/ crypt depth (VH/CD) of jejunum and ileum were increased (Linear, P < 0.05); The expression of tight junction proteins including zonula occludens protein 1(ZO-1), occludin (OCLN) and closure protein 1(CLDN-1) in the jejunum mucosa were up-regulated (Linear, P < 0.05), the mRNA abundance of ZO-1, OCLN and CLDN-1 were up-regulated (P < 0.05),and the D-lactose (D-LA) content in blood was down-regulated (Linear, P < 0.05); the colonization abundance of Firmicutes was increased (Linear, P < 0.05), while Proteobacteria and Spirochaetota was decreased (Linear, P < 0.05); The diarrhea index decreased (Linear, P < 0.05), while the feed conversion rate increased (Linear, P < 0.05). Collectively, supplementation of 0.3% and 0.4% taurine in feed can significantly alleviate intestinal oxidative damage by enhancing antioxidant capacity of piglets, and improve feed utilization of piglets after repairing intestinal damage.

Different external stimuli are perceived by multiple sensor histidine kinases and transmitted by phosphorylation via the phosphotransfer protein Ypd1p in the multistep phosphorelay system of the high osmolarity glycerol signaling pathway of filamentous fungi. How the signal propagation takes place is still not known in detail, since multiple sensor histidine kinase genes in most filamentous fungi are coded in the genome, whereas only one gene for Ypd1 exists. That raises the hypothesis that various Ypd1 isoforms are produced from a single gene sequence, perhaps by alternative splicing, facilitating a higher variability in signal transduction. We found that the mRNA of MoYPD1 in the rice blast fungus Magnaporthe oryzae is subjected to an increased structural variation and amplified putative isoforms on a cDNA level. We then generated mutant strains overexpressing these isoforms, purified the products and present here one previously unknown MoYpd1 isoform on a proteome level. Alternative splicing was found to be a valid molecular mechanism to increase the signal diversity in eukaryotic multistep phosphorelay systems.

This study assessed the relationship between body posture displacements and cardiopulmonary function test (CPET) and skill related physical fitness tests. One hundred male (60%) and female collegiate athletes (22.2 ± 4yrs) with a normal body mass index (BMI up to 24.9) were assessed via the PostureScreen Mobile app to quantify postural displacements as head, thorax and pelvis rotations and translations. CPET and physical performance tests including the agility T-test, the vertical jump test, the stork static balance test (SSBT) and the dynamic Y-balance test (YBT) were performed. Spearman correlation (r) and p-values are reported. Postural parameters were found to have moderate-to-high associations with CPET and the agility test, moderate correlations with the vertical jump test and the SSBT (head and pelvic postures only), and weak correlations with the YBT. As postural parameters were more asymmetric, both CPET and performance skills scores were worse. For examples: 1) a medium positive correlation was found between cranio-vertebral angle (CVA) and vertical jump test (r = 0.54; p-value < 0.001) and SSBT (r = 0.57; p-value < 0.001), while a strong negative correlation was found between CVA and agility test (r = -0.86; p-value < 0.001). 2) A strong positive correlation was found between CVA and oxygen uptake efficiency slope, load watts VO2 at VT, VO2 / kg, load watts at respiratory compensation point (RCP), (r = 0.65 and r = 0.71; p < 0.001). Conversely, a significant negative correlation was found between CVA and VE / VO2 at VT (r = -0.61; p < 0.001). Postural rotations and translations of the head, thorax and pelvis were statistically correlated with physical performance skills and CPET in young collegiate athletes. There were moderate-to-high associations with cardiopulmonary functions and agility tests, moderate correlations with the vertical jump test, and weak correlations with the YBT. Postural alignment may be important for optimal physical performance and optimal cardiopulmonary function. Further research is necessary to elucidate reasons for these correlations as found in our sample of young and healthy athletes.

Nitraria tangutorum Bobrov is a berry shrub with white flowers and red fruits, which grows in the deserts in the Tibetan Plateau, Mongolia, and western China. Its fruit N. tangutorum fruit (NTF) contains various bioactive compounds, with anti-fatigue, anti-inflammatory, and neuroprotective functions. However, the high saccharide content of NTF makes it unsuitable for diabetic patients. In this study, we fermented NTF to obtain N. tangutorum fermented juice (NTJ), and N. tangutorum fermented residue (NTR), which are suitable for diabetics to consume. We characterized the bioactive compounds in NTF, NTR, and NTJ, and found that fermentation increased the diversity of bioactive compounds, and greatly reduced sucrose, glucose, and fructose content while generating trehalose, which has the potential to manage blood glucose levels. Further, NTJ displays anti-diabetic potential due to various compounds anti-diabetic properties. This study provides a basis for further clinical research on NTJ's anti-diabetic function in humans.

The paper is dedicated to the topical problem of examining permafrost state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we propose and scientifically substantiate a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings and constructions.

System-of-systems (SoS) approach is often used for simulating disruptions to business and infrastructure system networks allowing for integration of several models into one simulation. However, the integration is frequently challenging as each system is designed individually with different characteristics, such as time granularity. Understanding the impact of time granularity on propagation of disruptions between businesses and infrastructure systems and finding the appropriate granularity for the SoS simulation remain as major challenges. To tackle these, we explore how time granularity, recovery time, and disruption size affect the propagation of disruptions between constituent systems of an SoS simulation. To address this issue, we developed a High Level Architecture (HLA) simulation of 3 networks and performed a series of simulation experiments. Our results revealed that time granularity and especially recovery time have huge impact on propagation of disruptions. Consequently, we developed a model for selecting an appropriate time granularity for an SoS simulation based on expected recovery time. Our simulation experiments show that time granularity should be less than 1.13 of expected recovery time. We identified some areas for future research centered around extending the experimental factors space.

Wildland fires are responsible for large socio-economic impacts. Fires affect the environment, damage structures, threaten lives, cause health issues, and involve large suppression costs. These impacts can be mitigated via accurate fire spread forecast to inform the incident management team. We show that a fire forecast system based on a numerical weather prediction (NWP) model coupled with a wildland fire behavior model can provide this forecast. This is illustrated with the Chimney Tops II wildland fire responsible for large socio-economic impacts. The system is run at high horizontal resolution (111 m) over the region affected by the fire to provide a fine representation of the terrain and fuel heterogeneities and explicitly resolve atmospheric turbulence. Our findings suggest that one can use the high spatial resolution winds, fire spread and smoke forecast to minimize the adverse impacts of wildland fires.

There is a paucity of data on the progression of track cycling sprinters, and the evolution of training and performance over a training cycle. Following prior research showing relationships between sprint cycling power and endurance cycling power, we compared these relations over a 3-month period. Our hypothesis is large improvements in power would come from training either for sprint power or sprint capacity, and this would be reflected in the data. A total of publicly available 25 datasets. These data were plotted against the line of best fit for 30-s and 2-min power to assess if training towards the line led to better 30-s power. We observe the best performances came from riders who start below the 30-s vs 2-min power line of best fit, with greater capacity and ability to ride fast over a sprint series, and progressing towards focusing on specific power in the final block leading into a competition. These results support the hypothesis of combined capacity and power training based on rider-specific relationship to the line of best fit between these measures versus a strictly maximal power training focus.

In this paper, it is defined that how the IPOs are affected by the underwriter reputation. What will happen to IPOs who are backed by reputed underwriter and who is not? And evaluate the IPOs short-run and long-run performance. Also try to explain the relationship between IPOs and underwriter. Also tried to compare some of the international return and Pakistani returns. Also determine the relation of the investor to the underwriter. There is a set of investors who have there own relationship with the underwriters how they will affect on the IPOs in the market.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

Biofuels have many environmental and practical benefits as a transportation fuel. They are among the best alternatives to fossil fuels due to their capacity for negative carbon emissions, which is vital for archiving the global ambition of a Net-Zero Economy. However, conventional biofuel production takes place on inland sites and relies on freshwater and edible crops (or land suitable for edible crop production), which has led to the food vs fuel debate. It also suffers technical and economical barriers due to the energy balance and the cost of production compared to fossil fuels. Establishing a coastal integrated marine biorefinery (CIMB) system for the simultaneous production of biofuels, high-value chemicals, and other co-products could be the ultimate solution. The proposed system is based on coastal sites and relies on marine resources including seawater, marine biomass (seaweed) and marine microorganisms (marine yeasts and marine microalgae). The system will not require the use of arable land and freshwater in any part of the production chain and will be linked to offshore renewable energy sources to increase its economic and environmental value. This article aims to introduce the CIMB system as a potential vehicle for addressing global warming and speeding the global effort on climate change mitigation as well as increasing global water, food and energy security. I hope this perspective may serve to draw attention into research funding for this approach.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

Background: More than 270 million participants and 128,893 professional players play soccer. Research only weakly supports the impact of diets and supplements on the performance and recovery of professional soccer players. Methods: We conducted a comprehensive search in Pub-Med, Scopus, Web of Science, and clinical trial registers. Inclusion criteria focused on professional or semi-professional soccer players, nutrition or diet interventions, performance improvement outcomes, and randomized clinical trial study types. We assessed quality using the Risk of Bias 2 (RoB 2) tool. We identified 16 eligible articles involving 310 participants. No nutritional intervention during the recovery period effectively improved recovery. However, several perfor-mance-based interventions showed positive effects, such as tart cherry supplementation, raw pistachio nut kernels, bicarbonate and mineral ingestion, creatine supplementation, betaine consumption, symbiotic supplements, and a high carbohydrate diet. These interventions influenced various aspects of soccer performance, including endurance, speed, agility, strength, power, explosiveness, and anaerobic capacity. Conclusions: Specific strategies, such as solutions with bicarbonate and minerals, high carbohydrate diets, and supplements like creatine, betaine, and tart cherry, can enhance the performance of professional soccer players. These targeted nutritional interventions may help optimize performance and provide the competitive edge required in professional soccer. We did not find any dietary interventions that could enhance recovery during recovery.

This paper reports a novel fabric phase sorptive extraction-high performance liquid chromatography-ultra violet detection (FPSE-HPLC-UV) method for the simultaneous extraction and analysis of four phenyltin derivatives that include triphenyltin hydroxide, triphenyltin acetate, triphenyltin chloride and tetraphenyltin in environmental water (agricultural waste water and municipal waste water) and canned food samples. The selected analytes were well resolved by Waters Nova pack C18 column (3.9 x 150 mm, 4 µm particle size) in isocratic elution mode within 15 minutes. The new microextraction media has been analytically evaluated using phenyltin derivatives as model compounds. The factors affecting the extraction efficiency of FPSE have been evaluated and the optimum extraction conditions were determined. Under these optimum conditions, the limits of detection (LODs) for sol-gel C18 coated fabric phase sorptive extraction (FPSE) media in combination with HPLC-UV for the analysis of the phenyltin derivatives were in the range of 10-100 ng/mL with high precision (low relative standard deviation) at 10 ng/mL concentration with good absolute recoveries. To the best of our knowledge, this is the first FPSE extraction procedure applied to environmental water and canned food samples for the simultaneous determination of phenyltin derivatives and could be readily adopted as a rapid and robust green analytical tool for routine environmental and food analytical laboratories.

Solar heating technology is a promising solution to promote China to achieve the “3060 double carbon” target as soon as possible. And seasonal thermal storage (STS) can effectively solve the mismatch problem of solar heating systems between the supply and demand of thermal energy. Due to the instability of solar radiation resources and heat demand, it is necessary to analyze the dynamic response characteristics of the system. Yet, related studies are still scarce. In this study, a solar heating system with a solar tower receiver and STS was introduced in north China. The dynamic performance of the system is analyzed with a dynamic simulated method in a typical day or typical operation modes, and the switch mechanism between multiple operation modes is also revealed. The impact of different heating strategies on system performance was analyzed. Results showed that the solar fraction of the system reached 89.4% in the third year, which was 3.6% higher than the first year. The quality-quantity heating operation strategies can be effective ways to improve the discharge efficiency of STS and the system performance without any heat pump. The electricity consumption of the pump on the heating side could be significantly reduced by 44.6% compared with the quality control.

The aim of this study is to propose and validate the state space mode decomposition technique for precise mode separation of non-classical damping systems and closely distributed modal systems. To assess the reliability and applicability of this technique, a 40-story building with a tuned mass damper is investigated, and acceleration responses measured by the building's health monitoring system are used for the verification of the technique. The mode separation results reveal that the separated modal power spectrum becomes distorted at neighboring natural frequency ranges when the performance index only considers the concentration of power spectral energy at the target natural frequency. However, by introducing an augmented performance index that includes a constraint condition to account for distortion, more accurate mode decomposition can be achieved.

This paper presents a method to detect and classify the high impedance fault that occur in the medium voltage distribution network using discrete wavelet transform (DWT) and adaptive neuro-fuzzy inference system (ANFIS). The network is designed using Matlab software and various faults such as high impedance, symmetrical and unsymmetrical fault have been applied to study the effectiveness of the proposed ANFIS classifier method. This is achieved by training the ANFIS classifier using the features (standard deviation values) extracted from the three phase fault current signal by DWT technique for various cases of fault with different values of fault resistance in the system. The success and discrimination rate obtained for identifying and classifying the high impedance fault from the proffered method is 100% whereas the values are 66.7% and 85% respectively for conventional fuzzy based approach. The results indicate that the proposed method is more efficient to identify and discriminate the high impedance fault accurately from other power system faults in the system.

Background: In regenerative dentistry the graft material influences the success. It should act as an osteoconductive scaffold, providing a mineral substrate during resorption and inducing the activity of osteoinductive cells capable of producing new bone, platelet growth factors, and cell differentiation factors inducing the differentiation of undifferentiated mesenchymal cells into. Given that dentin shares many biochemical characteristics with bone tissue, it has recently attracted considerable interest as a biomaterial for bone repair. The aim of this study is to compare two grinder types in order to determine the optimal method for producing dentinal particles using a mechanical grinder. Materials and methods: A sample of 40 natural human teeth without restorations, prostheses or root canal treatments was used and divided into two groups subjected to two different grinder speeds (high-speed and low-speed). The high-speed showed a greater dispersion (53.5+-9.89% of the tooth) due to the pulverisation (highly thin granules) of part of the tooth. The low-speed grinder does not pulverize the dentin and the percentage of tooth loss is 9.16+/-2.34%. Conclusion: The low-speed gringer allows to save a major part of the tooth and to have a maximum quantity of graft material but requires more time. Further studies must be promoted to optimise the grinding procedures.

Emotional intelligence may help nurses to cope with demanding work environments. Although it is well known that emotional intelligence is positively related to work performance literature on nurses is limited. The aim of our study was to examine the impact of emotional intelligence on work performance in a sample of nurses in Greece. We conducted a cross-sectional study in Greece. We collected data from a convenience sample of nurses during January 2024. We measured emotional intelligence with the Trait Emotional Intelligence Questionnaire-Short Form (TEIQue-SF), and work performance with the Individual Work Performance Questionnaire (IWPQ). We created multivariable linear regression models adjusted for sex, age, educational level, and work experience. We found that the four streams of emotional intelligence (i.e. well-being, self-control, emotionality, sociability) increases nurses’ work performance. In particular, we found a positive relationship between well-being and task performance and contextual performance. Similarly, there was a positive relationship between self-control and task performance. Additionally, sociability increased task performance and contextual performance. Moreover, emotionality and sociability reduced counterproductive work behavior. Our multivariable models identified a positive impact of emotional intelligence on nurses’ work performance. Nurses managers and healthcare organizations should adopt appropriate interventions to improve nurses’ emotional intelligence.

Pump-as-turbines (PAT) have been widely used during the last decade as one of the most interesting technologies in the field of energy recovery. A large number of studies and papers have been published in which the performance of the pumps in the turbine operating regime are analysed. Since horizontal single stage centrifugal norm pumps are most commonly used as PATs, their performances are analysed in this paper. Most of the research was related to individual pump aggregates or smaller groups and to obtaining their performance curves in turbine random mode. In this work, extensive experimental, numerical and theoretical investigations are conducted to obtain complete dimensionless performance characteristics of the single stage centrifugal norm pumps operating as turbines. The main goal of this research was to form a simple analytical expression that will, for this type of aggregate, map the pump operating characteristic to the appropriate turbine operating regime. By using the expressions obtained and presented in the work, engineers are enabled to make the appropriate choice of pump aggregate for operation in the turbine random mode for potential locations. This can allow us to quickly make selection of potential locations and to carry out appropriate techno-economic analyses and analyses of possible energy savings.

In recent years, with the increasing prominence of environmental and social issues, investors have been paying more attention to the ESG performance of enterprises, highlighting the importance of ESG factors in the financial field. This study is based on the theories of banking business models, stakeholder theory, risk management theory, and ESG investment theory. It uses the financial data and ESG scores of Chinese listed banks to deeply analyze the ESG factors and explore their impact on the liquidity risk of commercial banks. The research found that (1) good ESG performance can reduce the liquidity risk commercial banks face by improving bank value and financial performance. (2) ESG factors can also enhance the liquidity management level of commercial banks through standardization and sustainable business principles, thereby reducing the occurrence and impact of liquidity risk. Therefore, it is necessary to reduce the liquidity risk of banks and promote the sustainable development of commercial banks from four aspects: ESG performance and management, bank value, financial performance, and policy regulation.

The purpose of this study is to examine the match-related performance (scores and penalties) of the athletes in the Junior EJC (European Judo Championship) and U23 EJC categories before and immediately after the Covid-19 quarantine, according to gender and weight category groups. Our sample was based on the junior and U23, male and females, 2019-2020 Junior European Judo Championships and 2019-2020 U23 European Judo Championships. A total of 1431 matches in these tournaments were analyzed: male (n=812) and female (n=619). The main findings of this study showed that most matches in both the male and female categories resulted in ippon (2019-2020 average: 64,35% for Junior male, 70,55% for U23 male and 69,3% for Junior female, 64,4% for U23 female). No significant differences (p > 0.05) were observed between gender and age groups concerning the match scores. In the formation phase of the technique, considerations of high- and low-intensity actions, and analysis of the speed of athletes during matches in official competitions can help to better understand the dynamics of the variability of movements in judo matches. In addition, suggestions are presented to be applied to athletes in different age categories who are on the way to become Olympic athletes.

This study established a relationship between computerized accounting information systems (CAISs) and performance of SMS business enterprises in Burao, Somaliland. The main three objectives of this study were; (1) to assess the impact of computerized accounting information System on the performance of SMS business enterprises in Burao. (2) To measure the role of CAIS in the control system and management performance of SMS business enterprises in Burao. (3) To measure the impact of CAIS on the financial and operational performances in SMS business enterprises in Burao. The research approach of the study was quantitative research approach. The data used in this study was primary data obtained from the results of questionnaire survey on respondents. It was also utilized secondary data from the national documents, reports, different books, published materials and websites on the topic under the study. Using Slovene's formula, a sample size of 150 was used to collect data from respondents at SMS business enterprises in Burao through purposive sampling techniques. The data was analyzed through use of descriptive and inferential statistics. Reliability test and Validity test were also employed to test consistency of the measure and validity of data collected. The research findings indicated that there is a positive relationship between CAIS and the Performance of SMS business enterprises in Burao. This study recommended that SMS business should take advantage of the excellent benefits derivable from the adaption of well-designed CAIS because this will help to achieve a high and acceptable standard of quality in the performance of their business operations. The Management of SMS business enterprises (using CAIS) will benefit from this study understanding the impact of CAIS on their business practices. The academic generation and researchers will also benefit from the study in terms of literature review in matters of computerized accounting systems. In other terms, this will act as a point of reference for other future researchers.

This study presents a detailed comparative analysis of Molecular Docking data, focusing on the binding interactions of conventional ligands and natural compounds, Apigenin and Luteolin, with TP-53, pRb, and APOBEC. Utilizing advanced bioinformatics techniques, coupled with Ar-tificial Intelligence software and High-Performance Computing (HPC), we measured and con-trasted the binding energies of these interactions. Additionally, we investigated protein-protein interactions between HPV-16 oncoprotein E6 and tumor suppressors TP-53 and pRb. Our findings demonstrate that the natural compounds Apigenin and Luteolin exhibit significantly higher binding affinities to TP-53, pRb, and APOBEC compared to conventional pharmacological ligands. The binding energies for Apigenin and Luteolin were approximately -6.9 kcal/mol and -6.6 kcal/mol, respectively, indicating their strong potential as therapeutic agents in inhibiting the oncogenic functions of HPV-16. In contrast, conventional ligands showed lower binding affinities, with energies around -4.5 to -5.5 kcal/mol. The study further revealed that the protein-protein interactions between E6 and TP-53, and E6 and pRb, exhibited considerably higher binding en-ergies, approximately -976.7 kcal/mol, due to the multiple interaction sites and the complex nature of protein interfaces. A conversion formula was developed to translate these high-energy inter-actions to a comparable scale for non-protein-protein interactions, highlighting the superior binding potential of natural compounds, which, through the same conversion formula, was shown to be higher than that of interaction between E6 with TP-53 and E6 with pRb. These results underscore the therapeutic promise of Apigenin and Luteolin in preventing HPV-16-related on-cogenesis. By demonstrating their higher binding affinities to crucial tumor suppressors, this study supports the development of natural compound-based therapies. The findings also em-phasize the necessity for further experimental validation to explore these compounds' efficacy in clinical settings. This comprehensive analysis provides a robust framework for understanding the comparative binding interactions and lays the groundwork for innovative therapeutic strategies against HPV-16.

Infectivity assays are the key analytical technology for development of manufacturing processes for virus-based therapeutics. Here, we introduce a novel assay format that utilizes label-free bright field images to determine the kinetics of infection-dependent changes in cell morphology. In particular, cell rounding is directly proportional to the amount of infectious virus applied, enabling rapid determination of viral titers in relation to a standard curve. Our kinetic infectious virus titer (KIT) assay is stability-indicating and, due to its sensitive readout method, provides results within 24 hours post-infection. Compared to traditional infectivity assays, which depend on a single readout of an infection endpoint, cumulated analysis of kinetic data by a fit model results in precise results (CV < 20%) based on only three wells per sample. This approach allows for a high throughput with ~400 samples processed by a single operator per week. We demonstrate the applicability of the KIT assay for VSV-GP and NDV, but it can potentially be extended to a wide range of viruses that induce morphological changes upon infection. The versatility of this assay, combined with its independence from specific instruments or software, makes it a promising solution to overcome the analytical bottleneck in infectivity assays within the pharmaceutical industry and as a routine method in academic research.

In this age of global warming, academics and policymakers are increasingly concerned about firm environmental sustainability success. Therefore, this study aims to investigate whether Environmental, Social and Governance (ESG) performance impacts sustainability performance through the mediating effect of firm innovation. To this end, Structural Equation Modeling (SEM) was deployed to analyze data collected from the employees of manufacturing industries in an emerging economy like Bangladesh. The results revealed that ESG performance significantly enhances the innovation and sustainability performance of manufacturing industries, indicating that the higher the ESG performance of a firm, the greater its innovation and sustainability performance. Furthermore, the results confirmed that firm innovation performance fully mediates the relationship between ESG initiatives and sustainability performance. The findings of this study provide policymakers and industry authorities with valuable insight into the role of ESG and innovation performance in improving sustainability performance. Specifically, the study sheds knowledge on how firm ESG initiatives and innovation performance impact sustainability performance in the manufacturing sector of an emerging economy like Bangladesh.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Cool roofs are roofing systems designed to reflect significant solar radiation, reducing heat absorption and subsequent cooling energy demands in buildings. This paper provides a comprehensive review of cool roof technologies, covering performance standards, material options, energy-saving potential, and hygrothermal considerations. The review examines provisions in current codes and standards, which specify minimum requirements for solar reflectance, thermal emittance, and solar reflectance index (SRI) values. These criteria often vary based on factors like roof slope, climate zone, and building type. Different cool roof materials are explored, including reflective paints and coatings that can be applied to existing roofs as cost-effective solutions. Several studies demonstrated the energy performance benefits of cool roofs, showing significant reductions in cooling loads, indoor air temperatures, peak cooling demand, and overall cooling energy consumption compared to traditional roofs. However, hygrothermal performance must be evaluated, especially in cold climates, to optimize insulation levels and avoid moisture accumulation risks, as reduced heat absorption can alter moisture migration patterns within the building envelope. While cool roofs provide substantial energy savings in hot climates, further research is needed to validate modeling approaches against real-world studies, investigate the impact of seasonality and green spaces on cool roof efficacy and urban heat island mitigation, and explore energy savings potential, moisture control, and condensation risks in cold and humid environments.

Ice and snow on roads in winter endanger traffic safety. The existing methods of snow and ice removal have various drawbacks, which need further research. Aiming at solving limitations about high labor intensity, low efficiency, serious environmental pollution of traditional snow and ice removal methods, the anti-icing coating technology of high-voltage conductors is used for reference, and in view of the characteristics of asphalt pavement deicing, an ice-suppressing material that can effectively reduce the adhesion between snow, ice and pavement is successfully developed. As there is no perfect evaluation index and method for ice-suppressing materials at present, this paper further evaluates the performance of ice-suppressing materials from the aspects of deicing performance, durability, adhesion and the impact of ice-suppressing materials on pavement performance. The test results show that the ice-suppressing material can effectively reduce the adhesion between the ice layer and the specimen, making it easier to remove. The ice-suppression material has good slow-release performance, and the specimens still have good deicing performance after 7 cycles of tests.

In the current study, we assessed the effects of conventional and Ultra High Dose Rate (UHDR) irradiation on behavioral and cognitive performance one month following exposure and assessed whether these effects were associated with alterations in the number of immune cells in the hippocampus using flow cytometry. Conventional- and UHDR-irradiated mice showed impaired novel object recognition. During fear learning, conventional- and UHDR-irradiated mice moved less during the inter-stimulus-interval (ISI) and UHDR-irradiated mice also moved less during the baseline period (prior to the first tone). In irradiated mice, reduced activity levels were also seen in the home cage; conventional- and UHDR-irradiated mice moved less during the light period and UHDR-irradiated mice moved less during the dark period. Following behavioral and cognitive testing, infiltrating immune cells in the hippocampus were analyzed by flow cytometry. The percent Ly6G+ CD45+ cells in the hippocampus was lower in conventional- and UHDR-irradiated than sham-irradiated mice, suggesting that neutrophils might be particularly sensitive to radiation. The percent of Ly6G+ CD45+ cells in the hippocampus was positively correlated with the time spent exploring the novel object in the object recognition test, suggesting that the reduced percent Ly6G+ CD45+ cells in the hippocampus might mediate some of the detrimental radiation-induced cognitive effects.

The Inefficient water use, varying and low productivity in Kenya public irrigation schemes is a major concern. It is therefore necessary to periodically monitor and evaluate the performance of public irrigation schemes. The performance of public irrigation in western Kenya was assessed by combining benchmarking methodology and principal component analysis. The aim was to quantify and rank the performance of pumped public irrigation schemes in Kenya. Eleven benchmarking indicators were computed for the period from 2012 to 2016 and compared to global benchmark values. The indicators used fall under agricultural productivity, water supply and financial performance categories. The computed agricultural productivity was 36%–51% in Ahero, 23%–42% in West Kano and 26%–50% Bunyala irrigation scheme. Water supply performance in Ahero, West Kano and Bunyala irrigation schemes varied from 24% to 58%, 3% to 49% and 19% to 43% respectively. Financial performance varied from 46% to 54% in Ahero, 25% to 32% in West Kano and 54%–56% in Bunyala irrigation scheme. An average overall performance efficiency of 46%, 39% and 31% was obtained in Ahero, Bunyala and West Kano irrigation schemes respectively. The performance of the irrigation schemes is very poor and measures on improving performance are needed.

Background: Chronic exposure to severe hypoxia causes an increase in hematocrit (Hct) and hemoglobin concentration ([Hb]), which can lead to Excessive Erythrocytosis (EE), which could impact physical performance. This work aims to determine the differences in the six-minute walking test (6MWT) outputs between EE and healthy subjects residing at more than 5000 meters. Methods: A prospective, cross-sectional study was performed on 71 men (36 healthy and 25 suffering EE) living in La Rinconada, Peru (5100 m). Basal levels of [Hb] and Hct were obtained. All the subjects per-formed the 6MWT, and distance reached, vital signs, dyspnea, and fatigue (Borg scale) at the end of the test were recorded. Results: The average [Hb] and Hct levels in the control group were 18.7 ± 1.2 g/dL and 60.4 ± 7.1%, respectively, contrasting with EE subjects who showed 23.4 ± 1.6 g/dL and 73.6 ± 5.9% (p < 0.001). However, no statistically significant differences were observed in BMI or other anthropometric parameters. At the end of the 6MWT, the distance traveled, and vital constants were similar between both groups, except for arterial oxygen saturation which was consistently lower in subjects with EE along the test. Conclusion: EE does not significantly affect 6MWT performance at high altitudes nor the hemodynamic control during moderate aerobic exercise of subjects who live permanently in a severe hypoxic environment.

Recent media reports commented about a possible antidiabetics’ misuse issue related to molecules promoted as a weight-loss treatment in non-obese people. We evaluated here available pharmacovigilance misuse/abuse signals related to semaglutide, a glucagon-like peptide-1 (GLP-1) analogue, in comparison to other GLP-1 receptor agonists (albiglutide; dulaglutide; exenatide; liraglutide; lixisenatide; tirzepatide) and the phentermine-topiramate combination. To that aim, we analysed the Food and Drug Administration-FDA Adverse Events Reporting System (FAERS) dataset, performing a descriptive analysis of adverse event reports (AER) and calculating related pharmacovigilance measures, including the reporting odds ratio (ROR) and the proportional reporting ratio (PRR). During January 2018-December 2022, a total of 31,542 AER involving the selected molecules were submitted to FAERS; most involved dulaglutide (n=11,858; 37.6%) and semaglutide (n=8,249; 26.1%). In comparing semaglutide vs the remaining nolecules, the AER ‘drug abuse’, ‘drug withdrawal syndrome’, ‘prescription drug used without a prescription’ and ‘intentional product use issue’ respective PRR values were 4.05, 4.05, 3.60 and 1.80 (all<0.01). The same comparisons of semaglutide vs the phentermine-topiramate combination were not associated with any significant differences. To the best of our knowledge, this is the first study documenting the misusing/abusing potential of semaglutide in comparison with other GLP1 analogues and the phentermine-topiramate combination. Current findings will need to be confirmed by further empirical investigations to fully understand the safety profile of those molecules.

Recent media reports commented about a possible antidiabetics’ misuse issue related to molecules promoted as a weight-loss treatment in non-obese people. We here evaluated available pharmacovigilance misuse/abuse signals related to semaglutide, a glucagon-like peptide-1 (GLP-1) analogue, in comparison to other GLP-1 receptor agonists (albiglutide; dulaglutide; exenatide; liraglutide; lixisenatide; tirzepatide) and the phentermine-topiramate combination. To that aim, we analysed the Food and Drug Administration-FDA Adverse Events Reporting System (FAERS) dataset, performing a descriptive analysis of adverse event reports (AER) and calculating related pharmacovigilance measures, including the reporting odds ratio (ROR) and the proportional reporting ratio (PRR). During January 2018-December 2022, a total of 31,542 AER involving the selected molecules were submitted to FAERS; most involved dulaglutide (n=11,858; 37.6%) and semaglutide (n=8,249; 26.1%). In comparing semaglutide vs the remaining antidiabetics, the AER ‘drug abuse’, ‘drug withdrawal syndrome’, ‘prescription drug used without a prescription’ and ‘intentional product use issue’ respective PRR values were 4.05, 4.05, 3.60 and 1.80 (all<0.01). The same comparisons of semaglutide vs the phentermine-topiramate combination were not associated with any significant differences. To our best, this is the first study documenting the misusing/abusing potential of semaglutide in comparison with other novel antidiabetics and the phentermine-topiramate combination. Current findings will need to be confirmed by further empirical investigations to fully understand the safety profile of those molecules.

This study aimed to analyze the effect of a flow training program based on mindfulness applied to young and adult elite handball athletes. A quantitative, quasi-experimental, descriptive data analysis approach was carried out. The sample included 105 athletes (51 female and 54 male). The athletes were divided into two groups: i) experimental (n = 53) and ii) control (n = 52). The results of the repeated ANOVA indicated that the experimental group achieved significant improvements compared to the control group in decision making (n2p=.086), mental well-being (n2p=.045), dispositional flow state (n2p=.103), non-judgment (n2p=.040), refocusing (n2p=.052) and mindful trait in daily life (n2p=.058). In the linear regression test, the factor non-judgment was identified as a predictor of decision making (F(103)=7.99, p=.006) and the predictor for the mental well-being were dispositional flow state (F(102)=29.2, p

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

Banks have enormous potential in supporting the achievement of sustainable development goals (SDGs) in accordance with their function as financial intermediaries through sustainable lending. However, the average national financing growth for the sustainable business activity category over the past four years is still 12%. The aim of this research is to identify the conditions of sustainable lending at state-owned conventional banks and analyze the influence of the value chain, economic performance and ESG performance on sustainable lending. The research was conducted at state-owned commercial banks in Indonesia. The research utilized a Structural Equation Modeling (SEM). The SEM results of this study describe value chain, ESG performance (environmental, social and governance) and economic performance have direct and positive influences on sustainable lending, of which ESG performance has the biggest influence. As per individual aspect, social orientation gives the biggest contribution toward sustainable lending.

Risk management strategies protect the company as a whole as well as employees from unforeseen financial impacts. As in the case of personal finance, preparing for certain scenarios helps to face any difficulties that the company may encounter and allows it to get out of this impasse.For any project to be successful, the way the project executing agency will deal with potential risks must be determined so that it can identify, mitigate or avoid problems when it needs to do so. Successful project managers realize that risk management is important, because the achievement of project objectives depends on planning, preparation, results and evaluation that contribute to the achievement of strategic goals, especially the sustainable development of societies.Risk management strategies work to protect the company as a whole as well as employees from unexpected financial effects, and as is the case in personal finance, preparing for certain scenarios helps to face any difficulties that the company may face and allows it to get out of this impasse.To ensure the success of your project, determine how you will handle potential risks so that you can identify, mitigate or avoid problems when you need to do so. Successful project managers understand that risk management is important, because the achievement of project objectives depends on planning, preparation, results, and evaluation that contribute to the achievement of strategic objectives.

Covid-19 is a disease caused by SARS-CoV-2, which has spread worldwide since the beginning of 2020. Several pharmaceutical and non-pharmaceutical strategies were proposed to contain the virus dissemination, including vaccination and lockdowns. One of the consequences of the pandemic was the denial or delay of access to convenient health care services, but also potentially the increase of adverse events within those services, like the number of hospital infections. Therefore, the main question here is: What happened to the performance and sustainability of hospitals? The main goal of this work was to test if the Portuguese public hospitals' performance has been affected by the SARS-CoV-2 pandemic. We used the Benefit-of-Doubt method integrated with the Malmquist Index to analyze the performance evolution over time. Then, we employed a multiple regression model to test whether some pandemic-related variables could explain the performance results. We considered a database of 40 Portuguese public hospitals evaluated from January 2017 to May 2022. The period 2017 to 2019 corresponds to the baseline (pre-pandemic), against which the remaining period will be compared (during the pandemic). We also considered fourteen variables characterizing hospital quality, divided into three main performance definitions (efficiency and productivity; access; safety and care appropriateness). As potential explanatory variables, we consider seven dimensions, including vaccination rate and the need for intensive care for Covid-19 infected people. Results suggest that Covid-19 pandemic features help explain the drop on access after 2020, but not the evolution of safety and appropriateness of care, which surpris-ingly increased the whole time.

The paper deals with the design of a systematic procedure for implementing strategy changes into internal business processes for a project-oriented production type of organization. In the first part of the contribution, a summary of the theoretical starting points for the field of strategic management and change management is presented. In the second part, the contribution deals with the analysis of the current situation in the area of the impact of the change of strategy on the management of business processes. In the last part, the proposal of the procedure for implementing strategy changes into internal business processes and the verification results are presented. The proposed procedure includes steps where the selection and verification of key performance indicators at individual levels of management plus the quantification of the impact of the change in strategy on the processes takes place. The management can thus monitor and evaluate the chosen processes in accordance with the fulfilment of the chosen strategy of the company. The last chapter presents the verification of the proposal for the systematic introduction of changes into the processes.

This paper presents preliminary operational performance results of a pilot grid-connected photovoltaic (PV) system designed and installed on the rooftop of the Ministry of Petroleum, Energy and Mining headquarter in Nouakchott (latitude of 18.1°N and the longitude of 16.0°W), Mauritania. The aim is for the government to demonstrate the relevance of using solar energy and to encourage the uptake of solar PV technology for commercial and residential building applications in Mauritania.. In this study, the grid-connected PV system has a peak power of 48 kW and the performance monitoring was carried out during one year, with a system that allow to measure DC power, inverter and system conversion efficiency, energy generated by the PV arrays, solar radiation in the inclination plane of panels, ambient temperature and module temperature. During this period, the PV plant was found to supply 65,668 kWh to the grid. The final yield ranged from 3.91 to 5.09 kWh/kWp/day. The performance ratio was found to vary from 69.69% to 89.35% and the annual capacity factor was found to be 19%. Finally, performance parameters were compared with other PV plants installed in the same region of Northern Africa. The outcome of this work is deemed important in assisting accurate PV system design and decision-making.

This study investigated the impact of sustainability reporting on financial performance, with a focus on companies in the Turkish food, beverage and tobacco and textile, wearing apparel and leather sectors. The sustainability reports of 48 companies listed on the Istanbul Stock Exchange for 2022 were studied, and the quality of sustainability practices was determined by using a general index (Sustainability Reporting Disclosure Quality Index (SRDQI)) and three partial indices (Environmental Disclosure Quality Index, Social Disclosure Quality Index, and Corporate Governance Disclosure Quality Index (CGDQI)). To analyze the relationships between financial performance and sustainability practices two types of regression models were developed, based on which eight models were directly examined. The results indicate the complete absence of a statistically significant impact of SRDQI on all financial performance measures used. Among the partial indices, only CGDQI has a significant positive effect on the Assets Turnover Ratio. An analysis of the influence of control variables shows a multidirectional dependence of individual financial performance measures on the size of companies, their age, industry affiliation, as well as on the structure of capital used. Finally, this study provides directions for improving the institutional environment of sustainability reporting for Turkish companies.

Asphalt binder is a temperature sensitive material, whose performance is greatly affected by the climate change of the environment. Improper selection of asphalt will cause a lot of damage and affect the durability of the road. The establishment of asphalt pavement performance zoning in Xinjiang, a vast area with great temperature difference, will provide reference for the selection of asphalt suitability, the refinement of pavement design and the sustainable development of road engineering. In this study, 11 years of temperature data in Xinjiang region were collected and analyzed, and 98% reliability of pavement design temperature was used to draw a performance grading map of asphalt pavement in Xinjiang region based on ArcGIS platform. Finally, Xinjiang region was divided into 9 performance zones. At the same time, the performance grade (PG) of five kinds of asphalt binders in Karamay were explored. The result shows that there is little difference in continuous PG span between different matrix asphalt binders, the lower penetration grade, the better high temperature performance, the worse low temperature performance. After adding SBS modifier, the continuous PG span can be higher than the matrix asphalt in 20 ℃. All these provide the basis for reasonable selection of asphalt binders in different areas of Xinjiang.

Performance appraisal is a fundamental indicator in public accountability to achieve the good governance principles. Hence, this study aims to analyze the performance measurement that can improve performance on government agencies in South Sulawesi, Indonesia. The study was conducted in qualitative approach. The research found that non-integrated models of performance measurement in South Sulawesi are inefficient and ineffective. Inefficiency happens because it uses time and cost resources separately, while being ineffective is because both models focuses on each goal instead on performance goals and the process is not supported by the actual management.

Clustering is an important task in data mining that has become more challenging due to the ever-increasing size of available datasets. To cope with these big data scenarios, a high-performance clustering approach is required. Sparse grid clustering is a density-based clustering method that uses a sparse grid density estimation as its central building block. The underlying density estimation approach enables the detection of clusters with non-convex shapes and without a predetermined number of clusters. In this work, we introduce a new distributed and performance-portable variant of the sparse grid clustering algorithm that is suited for big data settings. Our compute kernels were implemented in OpenCL to enable portability across a wide range of architectures. For distributed environments, we added a manager-worker scheme that was implemented using MPI. In experiments on two supercomputers, Piz Daint and Hazel Hen, with up to 100 million data points in a 10-dimensional dataset, we show the performance and scalability of our approach. The dataset with 100 million data points was clustered in 1198s using 128 nodes of Piz Daint. This translates to an overall performance of 352TFLOPS. On the node-level, we provide results for two GPUs, Nvidia's Tesla P100 and the AMD FirePro W8100, and one processor-based platform that uses Intel Xeon E5-2680v3 processors. In these experiments, we achieved between 43% and 66% of the peak performance across all compute kernels and devices, demonstrating the performance portability of our approach.

Super-high (x400) magnification dermoscopy (D400) is a new non-invasive imaging technique that has been shown to add information for the differential diagnosis of melanocytic lesions in a pilot study. Our study aimed to confirm if D400 can add details for the discrimination of clinically atypical nevus and melanoma. This is a retrospective observational, multicentric study enrolling patients who received an x20 (D20) and x400 (D400) magnification dermoscopic examination of pigmented skin lesions. Dermoscopic images were retrospectively evaluated by three observers for the presence/absence of nine D20 and twenty D400 dermoscopic features defined in the previous pilot study. Univariate and multivariate analyses were carried out to find predictors of benign and malignant behaviors. At D20 atypical pigment network, blue-whitish veil, atypical vascular pattern, regression, and homogenous pattern were more frequent in melanoma than in nevi (p&lt;0.001). At D400 melanoma showed more frequently than benign lesions melanocytes with an irregular arrangement and irregular in shape and size (p&lt;0.001). Network with edged papillae was more frequent in benign lesions than melanomas (p&lt;0.001). Our study confirms that D400 can identify melanocytes with an irregular arrangement and irregular in shape and size in melanomas, adding information to the conventional D20 examination.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

In-situ injection of steam for heating of the subsurface is an efficient method for the recovery of oil and gas from oil shale where permeability typically evolves with temperature. We reported measurements on Jimusar oil shales(Xinjiang, China) at different temperatures to 600℃ and under recreated in situ triaxial stresses to obtain permeability evolution with temperature and stress. Permeability of tight oil shales evolves with temperature to a threshold temperature and peak temperature. The threshold temperature was subjected to triaxial stresses. For Jimusar oil shale, the threshold temperature ranges from 200℃ to 250℃ at ground stress of buried depth of 500m and from 350℃ to 400℃ at buried depth of 1000m. The peak temperature was almost not subjected to triaxial stress and the range is from 450℃ to 500℃ for all Jimusar samples. Pyrolysis plays an important role in permeability evolution and fundamentally changes permeability tendency and magnitude. At high temperature permeability exhibits a little reduction due to stress effect but still remains a high level due to pyrolysis. The above results show that oil shale mass can change from tight porous media into highly permeable media and oil & gas can easily flow through oil shale stratum.

The importance of this study may be defined by using the smart techniques to earned value indicators of residential buildings projects in Republic of Iraq, only one development intelligent forecasting model was presented to predict Schedule Performance Index (SPI), Cost Performance Index (CPI), and To Complete Cost Performance Indicator (TCPI) are defined as the dependent. The approach is principally influenced by the determining numerous factors which effect on the earned value management, that involves Iraqi historical data. In addition, six independent variables (F1: BAC, Budget at Completion., F2: AC, Actual Cost., F3, A%, Actual Percentage., F4: EV, Earned Value. F5: P%, Planning Percentage., and F6: PV, Planning Value) were arbitrarily designated and satisfactorily described for per construction project. It was found that ANN has the capability to envisage the dust storm with a great accuracy. The correlation coefficient (R) has been 90.00%, and typical accuracy percentage has been 89.00%.

High-strength wastewaters from a variety of sources, including the food industry, domestic septage and landfill leachate, are often hauled to municipal wastewater treatment plants (WWTPs) for co-treatment. Due to their high organic loadings, these wastewaters can cause process upsets in both the WWTP’s liquid and solids treatment trains and consume organic treatment capacity, leaving less capacity available to service customers in the catchment area. A novel pre-treatment method, the Waste Activated Sludge-High Rate (WASHR) process, is proposed to optimize the co-treatment of high-strength wastewaters. The WASHR process combines the contact stabilization and sequencing batch reactor processes. It utilizes waste activated sludge from the municipal WWTP as its biomass source, allowing rapid start-up. Bench scale treatment trials of winery wastewater confirm the WASHR process can reduce loadings on the downstream WWTP’s liquid treatment and solids treatment trains. A case study approach is used to confirm the economic viability and environmental sustainability of the WASHR process compared to direct co-treatment using life cycle cost analyses and greenhouse gas emissions estimates.

Background Although high-density lipoprotein has cardioprotective effects, the association between serum high-density lipoprotein cholesterol (HDL-C) and hypertension is poorly understood. Objective We investigated whether low and high concentrations of HDL-C are associated with hypertension using a large healthcare dataset. Methods In a community-based cross-sectional study of 1,493,152 Japanese people aged 40–74 years who underwent a health checkup, blood pressures and clinical parameters, including nine HDL-C concentrations (20–110 mg/dL or over) were investigated. Results A crude U-shaped relationship was observed between the nine HDL-C concentrations and blood pressure in males (n = 830,669), while a left-to-right inverted J-shaped relationship was observed in females(n = 662,483). An age-adjusted logistic regression analysis showed J-shaped relationships (left-to-right inversion in females) between HDL-C and odds ratios for hypertension (≥140/90 mmHg), with lower limits of 60–79 mg/dL in males and 90–99 mg/dL in females, which were unchanged after adjusting for smoking, habitual exercise, alcohol consumption, and pharmacotherapy for hypertension, dyslipidemia, and diabetes. However, further adjustment for body mass index and serum triglyceride concentration revealed latent positive linear associations between HDL-C and hypertension, although the association between extremely high HDL-C (≥100 mg/dL) and hypertension was attenuated in non-alcohol drinkers. Conclusion Both low and extremely high HDL-C concentrations are associated with hypertension. The former association may be dependent on excess fat mass, which is often concomitant with low HDL-C, whereas the latter association may be dependent on frequent alcohol consumption.

Background: Monitoring the mobility of players during wheelchair sports is essential to support coaches in their understanding of the activity and in their training programming. However, the amount of information available from the monitoring tools, combined with a general approach to processing and a poor presentation of the data to the coaches, is not effective and remains unused. Thus, this study aimed to propose a simple and efficient algorithm for identifying locomotor tasks (static, forward/backward propulsion, pivot/tight/wide rotation) during wheelchair movements based on wheelchair kinematic data. Methods: A total of 36 wheelchair tennis and badminton players participated, completing at least one of three proposed tests: the star test, the figure-of-eight test, and the forward-backward test. Locomotor tasks were identified using a five steps procedure including data reduction, symbolic approximation and pattern logical search. Results: Using this method, 99% of locomotor tasks were properly identified for the star test, 95% for the figure-of-eight test and 100% for the forward-backward test. Conclusion: This method appears to be a valuable tool for a simple and clear identification and representation of locomotor tasks over extended periods of time. Future research should aim at applying this method to multiple wheelchair court sports matches or daily life declination.

Surfing is a growing, high participation recreational and competitive activity. It is relatively unique being performed on, in, and through water with a range of temperatures. In other sports, warm-up and heat retention have proved useful at augmenting performance and ameliorating injury risk. Little work has been done examining this in surfing. The purpose of this work was to measure thermal profiles in surfers with and without warm-up and passive heat retention, and secondarily to assess any potential influence on free surfing. A repeated measures pre- and post- design was adopted whereby participants surfed in an artificial wave pool following an active warm-up combined with passive heat retention (experimental condition), and after no warm-up (control). Core body temperature was measured both occasions. Our results showed a clear advantage to body temperature for the experimental condition versus control. Both groups showed a warm-up effect in the water itself, presumably due to further activity (e.g. paddling) and wetsuit properties. Finally, performance trended to being superior following warm-up. We conclude, body warmth in surfers may be facilitated by an active warm-up and passive heat retention. In free surfing this is associated with a trend towards better performance; it may also reduce injury risk.

Background: Manoeuvres esbarrada and volta sobre patas are fundamental movements in equestrian activities, yet their kinematics remain largely unexplored. Objectives: This observational study aimed to kinematically describe the movements of esbarrada and volta sobre patas in Criollo breed horses. Methods: Kinematic analysis was conducted on 31 Criollo horses executing esbarrada and volta sobre patas manoeuvres. Results: The esbarrada maneuver covered a distance of 4.28 ± 0.99m in 1.15 ± 0.11s at a velocity of 3.77 ± 0.55m/s. Angular kinematic variables revealed specific joint angles during the maneuver. In volta sobre patas, significant differences were found in spin duration and thoracic limb suspension between the first and second spins. Conclusions: Volta sobre patas demonstrated prolonged spinning duration and increased thoracic limb suspension in the second spin. Additionally, static conformation did not correlate with limb protraction angles during esbarrada.

The main purpose of the study was to study the effects of a specific rowing ergometer training program on the athletic performance of young adolescents (n=56; 11.73 ± 1.4 years old) com-pared to a workout based on general strength training. Eight-week training program was im-plemented, with four sessions per week and two-hours per session. Sample was divided in two groups: a control group (CG) that performed circuit training with exercises aimed at building general strength and an experimental group (EG) who focused on specifically training on a rowing ergometer (rowing machine). The data obtained in a rowing meter test over the compe-tition distance were analyzed to obtain the average power attained (W) at the beginning of the training, at the middle (4 weeks), at the end of the training (8 weeks) and one year after the ex-perimentation. The results show that, although both forms of training improve the average W obtained in both categories, the EG subjects (+29.94W) obtained better averages in all phases of the study compared to the CG (+5.88W). Furthermore, this increase was greater in male rowers (+ 34.06W) than in female rowers (+24.54W). These results reveal that a specific rower rowing ergometer training program has a significant effect than a general strength program and these effects can even be observed a year after the intervention.

The medical sector is of the utmost importance in every country for well-known reasons such as their economic development, national security, quality of life, and so on. Many researchers were dedicated to this topic, however, in Romania there are limited studies on this subject. One reason is that most of the businesses in this sector are individual enterprises or small family businesses. In our research paper we deploy several analysis methods to see the financial sustainability of companies operating in the medical industry. By analyzing a sample of 23931 companies and we have concluded that their performance has increase in the peak of the pandemic and that the financial stability is high. Our results are in line with other similar studies that were conducted in other regions.

Non-compliant (NC) structures are often encountered in building construction in developing countries. This is a condition whereby erected buildings do not follow regulatory standards, especially in the provision of reinforcements. Therefore, under an earthquake load, the structures do not have sufficient resistance against such load. The structural elements of the building, which often have NC conditions, are the beam-column joints because they do not contain adequate shear reinforcements due to installation difficulty. This study aims to determine the structural performance of the reinforced concrete (RC) frame, which has a reinforcement deficiency in the beam-column joints. Numerical simulation was conducted on the Kakaletsis structure model by modifying the reinforcement details at the joints to represent the NC conditions. The non-linear modeling and analysis of the structural model were carried out using ATENA software. The analysis showed that the reduction in shear reinforcements in the NC model joint caused a decrease in load-carrying capacity by about 26.04%. A shift was also observed in the collapse pattern, i.e., from the beam to the end of the column, causing global failure and reducing the undamaged but increasing more severely damaged condition. This showed that the NC structure, due to the non-conformance of reinforcement, significantly reduced the structure's performance.

This study offers a concise summary of the research that has been done on alternative methods of HRM. A survey of 47 articles on the topic of creative human resource management uncovered three primary schools of thinking. At its core, innovation in HRM entails nothing more than that. One such topic worthy of investigation is the way human resource management approaches new situations. Third, research on inventiveness in the business world has given rise to the concept of "innovative HRM." Each of these three approaches, as well as the theoretical underpinnings of each, will be covered in this article. The note wraps up with a discussion of the significance of the findings for next research as well as clinical practice.

We are in the era where various processes need to be online. However, data from digital learning platforms are still underutilised in higher education, yet, they contain student learning patterns, whose awareness would contribute to educational development. This limits development of adaptive teaching and learning mechanisms. In this paper, a model for data exploitation to dynamically study students progress is proposed. Variables to determine current students progress are defined and are used to group students into different clusters. K-means clustering is performed on real data consisting of students from a South African tertiary institution. Cluster migration is analysed and the corresponding learning patterns are revealed.

The authors propose in this study to evaluate financial performance applications for stock prices of the Indonesian Stock Exchange in manufacturing companies. The method of research used here is a quantitative descriptive method. In that statement, Indonesian Stock Exchange manufacturing companies between 2016 and 2018 are the population use in this research, using the sampling technique Purpose Sampling. This research uses secondary data from 2016 to 2018, the financial reports of Indonesian Stock Exchange manufacturing companies. The Indonesian stock exchange web site has been provided with all data sources at https://www.idx.co.id, and searching for www.google.id. Our analysis shows that book value prices and the net profit margin affect stock prices. The value of financial performance at the Indonesian Stock Bourses manufacturing companies' cost amounts to 64.5 percent, while other factors not listed in this study account for 35.4 percent.

High average power narrow-linewidth tunable solid-state lasers in the wavelength region between 2 to 3 μm are attractive light sources for many applications. This paper reports a narrow-linewidth widely-tunable laser system based on the polycrystalline Cr2+:ZnSe elements pumped by the repetitively-pulsed 2.1 µm Ho3+:YAG laser operating at the tens of kilohertz pulse rate. An advanced procedure of ZnSe-element doping and surface improvement was applied to increase the laser-induced damage threshold, which resulted in an increase of the output power of the Cr2+:ZnSe laser system. The high-average-power laser system comprised double master-oscillators and power amplifiers: Ho3+:YAG and Cr2+:ZnSe laser oscillators, and Ho3+:YAG and Cr2+:ZnSe power amplifiers. The output wavelength was widely tuned within 2.3-2.7 µm by an acousto-optical tunable filter inside the Cr2+:ZnSe master oscillator cavity. The narrow-linewidth operation at the pulse repetition rate of 20-40 kHz in a high-quality beam with the average output power up to 9.7 W was demonstrated.

Corporate Sustainability has garnered increasing attention within the business community, as corporates communicate to influence its stakeholders for building sustainable relationships. There has been a surge in research exploring its connection to firm performance but, existing studies lack a cohesive and concentrated approach. This study employs scientometric and bibliometric methods to analyse scientific production which signals a scarcity of research from developing countries, indicating a need for greater investigation. Focussing on specific subfields of Corporate Sustainability and Firm Performance, we analyze and narrow down the scope of our study to a focussed sample. Employing use of structured methods and PRISMA Protocol, this scientifically rigorous study, points towards identification of research themes linking sustainability practices to firm performance for achieving business excellence. It goes beyond mapping of literature, thereby establishing linkages to Sustainable Development Goals (SDGs). Our analysis reveals clusters centered on Environmental Performance, Firm Performance, Corporate Sustainability Reporting, Corporate Social Performance and Green Supply Chain Management with significant citations related to various SDGs. We make use of time series analysis to determine the future trends of research in the field. This scientometric and bibliometric analysis study contributes to a more focused understanding of the linkages between corporate sustainability and firm performance, emphasizing the need for cohesive research approaches to address the complexities of sustainable business practices and their implications for financial performance and the economy.

This article investigated the Automatic Generation Control(AGC) of multi-area multi-source interconnected systems with hydropower plants, thermal power plants, and wind energy. Adaptive Neuro-fuzzy controller integrated with the cascaded proportional-integral-derivative with filter (PIDF-PIDF) is a new cascaded controller (ANF-PIDF-PIDF) that has been presented as a secondary controller for applied hybrid power systems. The recent Skill Optimization Algorithm (SOA) is employed to optimize PIDF- PIDF controller parameter gains and the Adaptive Neuro-Fuzzy controller's inputs and output scaling factors. SOA is used to update the controller parameters with integral square error (ISE) employed as the objective function. A 1% step load disturbance was considered simultaneously in all three areas. The controller's performance is evaluated and compared with and without considering the effects of wind energy sources and non-linearity for ANF-PIDF-PIDF, PIDF-PIDF, and PIDF and it was determined that the ANF-PIDF-PIDF was the most efficient. The dynamic system performance is also compared with parallel high voltage direct current (HVDC) tie-lines. The investigation clearly shows that incorporating HVDC tie-line with multi-area, multi-source provides better dynamic performance in maximum amplitude, oscillation, and settling time. Additionally, sensitivity analysis is done and the optimum controller gains does not need to be reset to uncertain values in system loading conditions. All simulation results were evaluated using MATLAB 2016b.

With the ever-increasing rate, obesity has become an epidemiological problem throughout the globe comprising about 39% of the world population as of now. Among several reasons, disruption of the gut microbial ecosystem might contribute to the pathogenesis of metabolic disorders, including obesity, metabolic syndrome, type 2 diabetes, and other associated comorbidities. Though the mechanisms related to dysbiosis are unclear, diet might play a modulating role where different dietary approaches manipulate microbial richness and abundance as well as stability. For instance, shifting of Firmicutes and Bacteroidetes ratio in the gut might have a role in association with the dietary approaches and ingestion duration. Along with altered gut microbial composition, microbial metabolites such as short-chain fatty acids (SCFA) after ingestion of non-digestible dietary starches may have an impact on host metabolism by regulating lipogenesis, gluconeogenesis, and inflammation with potential associations to health and obesity. The dietary approaches like carbohydrates, fibre, protein, and/or fat diet at various arrangements can make a shift in the composition of gut microbiota if introduced for a short period. However, the unique pattern of the gut microbes usually remains the same along with the longer period of habitual diet. Though the short-term dietary intervention or circadian rhythm influences a transient change in gut microbes, other than habitual diet, the understanding related to long-term dietary change-induced permanent alterations is minimum. Alternatively, the usage of prebiotics, probiotics as well as postbiotics could be beneficial to overcome dysbiosis. This review highlights the current knowledge and the interaction between the human intestinal microbiota and diet as a modifying factor, in obesity allowing the scientists to uncover novel targets and tools to use as customized therapy.

The salt marshes, lying at the land-sea temperate interface, furnish a plethora of ecosystems services such as biodiversity niche support, ocean-climate change regulation, ornithology recreo-tourism or plant gathering by hand. They undergo significant worldwide losses due to their conversion into crop fields and to their spatial compression between the rising sea-level and the armoring shoreline. Their monitoring however requires to use a suite of remote sensing sensors to embrace the regional scale while capturing the plant details. This research innovatively adopts a multiscale approach using a cascading spaceborne and airborne process, from the 10-m Sentinel-2, through the 3-m Dove, to the 0.03-m unmanned airborne vehicle (UAV) imageries. The high to very high temporal resolution of the Sentinel-2 and Dove enabled to cover twenties and tens of km2 over five and four years, respectively, in the form of normalized difference vegetation index (NDVI) classes, associated with microphytobenthos, low, medium and high salt marsh vegetation, including the opportunistic Elyma genus. The NDVI was then modelled at the UAV scale (a few km2) using a three-layered NN prediction, providing the final near-infrared (NIR), and the intermediate red, green and blue reflectance imageries, calibrated/validated/tested with the Dove reflectance imageries (R2NIR=0.98, R2red=0.88, R2green=0.84, and R2blue=0.90). The 100fold increase in pixel size allowed to detect the decimeter-scale objects of the tidal flats and salt marshes, to enlarge the NDVI class ranges, and hold great promise to model other spectral bands at the UAV scale for further deeply enhancing the salt marsh mapping.

Most of the municipalities in the Gulf region are facing performance related issues in their municipal solid waste management (MSWM) systems. They lack to possess a deliberate inter-municipality benchmarking processes. Instead of identifying the performance gaps for their key components (e.g., personnel productivity, operational reliability, etc.) and adopt proactive measures, the municipalities primarily rely on an efficient emergency response. A novel hierarchical modeling framework, based on deductive reasoning, is developed for performance assessment of MSWM systems. Fuzzy rule based modeling using Simulink-MATLAB was used for performance inferencing at different levels, i.e., component, sub-components, etc. The model is capable of handling the inherent uncertainties due to limited data and imprecise knowledge base. The model’s outcomes can exclusively assist the managers working at different levels of organizational hierarchy for effective decision-making. Performance of the key component, assists the senior management to assess the overall compliance level of performance objectives. Subsequently, operation management can hone in the sub-components to acquire useful information for intra-municipality performance management. While, individual indicators are useful for inter-municipality benchmarking. The model has been implemented on two municipalities operating in Qassim Region, Saudi Arabia. The results demonstrate the model’s pragmatism for continuous performance improvement of MSWM systems in the country and elsewhere.