Graphene quality for use in biosensors was assessed in fabricated chips by a set of methods that includes atomic force microscopy (AFM), Raman spectroscopy, and low-frequency noise. It is shown that local areas of residues on the graphene surface, which arisen due to the interaction of graphene with a photoresist at the initial stage of chips development, leads to a spread of chips resistance (R) within 1-10 kΩ and to an increase in the root mean square (RMS) roughness up to 10 times that can significantly impair reproducibility of graphene parameters in biosensors chips. It was observed that the control of the photoresist residues after photolithography (PLG) by AFM and subsequent additional cleaning allow reducing the spread of R values in chips to 1–1.6 kΩ and obtaining RMS roughness similar to the roughness in pristine graphene before PLG. Monitoring of the spectral density of low-frequency voltage fluctuation (SU), which provides integral information about the defect system and quality of the material, makes it possible to identify chips with low graphene quality and with inhomogeneously distributed compressive stresses areas by the type of frequency dependence SU (f).

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

Non-canonical NF-kB signalling plays important roles in development and function of the immune system but also is deregulated in a number of inflammatory diseases. Although, NF-kB and HIF crosstalk has been documented, this has only been described following canonical NF-kB stimulation, involving RelA/p50 and the HIF-1 dimer. Here we report that the non-canonical inducer TNFSF14/LIGHT leads to HIF induction and activation in cancer cells. We demonstrate that only HIF-2a is induced at the transcriptional level following non-canonical NF-kB activation, via a mechanism dependent on the p52 subunit. Furthermore, we demonstrate that p52 can bind to the HIF-2a gene in cells. These results indicate that non-canonical NF-kB can lead to HIF signalling implicating HIF-2a as one of the downstream effectors of this pathway in cells.

Efficient use of the operating room (OR) is crucial for any hospital. One of the major inefficiencies in the OR is surgical cases not starting or finishing on time as scheduled. When a case is delayed, it affects all subsequent cases in that OR. This study uses discrete choice analysis to determine the significant factors, including team familiarity, that influence OR case on-time start and finish. A case is considered on-time if the documented procedure start and finish times are no more than 10 minutes after the scheduled start and finish times. The analysis uses surgical case data from a large tertiary referral hospital and academic center in Greenville, South Carolina. The case data includes all surgical cases (15,091) performed during regular workdays in 2013. Two binary logit models are developed: one for case on-time start and one for case on-time finish. Results indicate that higher team familiarity between surgeon and anesthesiologist, surgeon and circulating nurse, surgeon and scrub nurse, and surgeon and CRNA improve the likelihood of an OR case on-time start and on-time finish. This finding indicates that the OR scheduling staff in the study hospital make a concerted effort to schedule the surgical teams with members who have worked well together in the past.

Along with the familiar Rossby–Haurwitz waves, two-dimensional flows on the surface of a rotating sphere in the regime of zonostrophic turbulence harbour another class of waves known as zonons. Zonons are wave packets produced by energetic large-scale Rossby–Haurwitz wave modes `enslaving’ other wave modes. They propagate westward with the phase speed of the enslaving modes. Zonons can be visualized as enslaving modes’ `ringing’ in the enslaved ones with the frequencies of the former, the property that renders zonons non-dispersive. Zonons reside in high-shear regions confined between the opposing zonal jets yet they are mainly attached to westward jets and sustained by the ensuing barotropic instability. They exchange energy with the mean flow while preserving their identity in a fully turbulent environment, a feature characteristic of solitary waves. The goal of this study is to deepen our understanding of zonons’ physics using direct numerical simulations, a weakly non-linear theory, and asymptotic analysis, and ascertain that zonons are indeed isomorphic to solitary waves in the Korteweg - de Vries framework. Having this isomorphism established, the analysis is extended to eddies detected in the atmospheres of Jupiter and Saturn based upon the observed mean zonal velocity profiles and earlier findings that circulations on both planets obey the regime of zonostrophic macroturbulence. Not only the analysis confirms that many eddies and eddy trains on both giant planets indeed possess properties of zonons, but the theory also correctly predicts latitudinal bands that confine zonal trajectories of the eddies.

Wobbling motion as an exotic collective mode in nuclei without axial symmetry, was intensively discussed during the last few years. The observation of the newly proposed transverse wobbling, first reported in $^{135}$Pr and soon after in nuclei from other mass regions, was considered as a significant discovery in low-spin nuclear structure. However, both the reported experimental results and the proposed theoretical models were lively questioned in a series of works devoted to the investigation of the low-spin wobbling mode in the same nucleus. The electromagnetic properties of the $\Delta I=1$ transitions connecting the one- to zero-phonon and the two- to one-phonon wobbling bands in $^{135}$Pr were recently remeasured, demonstrating their predominant $M1$ magnetic character which is in contradiction with the wobbling motion interpretation. These new experimental observables being well reproduced by both quasiparticle-plus-triaxial-rotor model and interacting boson-fermion model calculations, are against the previously proposed wobbling characteristics of the low-spin bands in $^{135}$Pr. On the other hand, we obtained conclusive experimental evidence for the theoretically suggested transverse wobbling bands at medium spin in $^{136}$Nd. The comparison of the experimental data with calculations utilizing the triaxial projected shell model and a new developed particle-rotor model with frozen orthogonal geometry of the active nucleons, supports the description in terms of transverse wobbling of medium-spin bands in triaxial even-even nuclei.

Background: This is a propensity matched, single centre study of limited versus extended resections for Type A acute aortic dissections (AAAD). Methods: Retrospective data for 440 patients with acute Type A aortic dissection repairs (Limited Resection, LR-215, Extended Resection, ER-225). 109 pairs were propensity matched to LR versus ER. Multivariate analysis was performed for inpatient death, long term survival and composite of inpatient death/TIA/stroke. Kaplan Meier survival curves were compared at 1, 3, 5, 10 and 15 years using the log-rank test. Results: Mean age was 66.9±13 years and mean follow up was 5.3±4.7 years. 48.9% had LR. In-hospital mortality was 10% (LR;6% vs ER;13.8%, p<0.01). ER, NYHA class, salvage surgery and additional procedures were predictors of increased mortality in unmatched data. Propensity matched data showed no difference in TIA/stroke rates, LOS, in-patient mortality or composite outcomes. LR had better survival (LR; 77.1% vs ER; 51.4%, p<0.001). ER (OR; 1.97, 95%CI; 1.27, 3.08, p=0.003) was a significant predictor of worse long term survival. At 15 years, aortic re-operation was 17% and freedom from re-operation and death was 42%. Conclusions: Type A aortic dissection repair has high mortality and morbidity although results have improved over two decades. ER was predictor of worse perioperative results and long term survival.

In this study we analyzed the concentration of lipoprotein(a) [Lp(a)], PCSK9-Lp(a) complexes and the circulating monocyte subsets in coronary atherosclerosis. 257 patients with coronary atherosclerosis (CA) and 68 patients without stenotic atherosclerosis in the coronary, carotid and lower extremity arteries (control group) were enrolled. Monocyte subpopulations (classical CD14++CD16-, intermediate CD14++CD16+, non-classical CD14+CD16+) were analyzed by direct immunofluorescence and flow cytometry. Lp(a) and PCSK9-Lp(a) complexes in serum were detected by ELISA. The concentration of Lp(a) was higher in CA group compared to controls (23.0 (9.1;73.3) mg/dL versus 10.7 (4.7;25.0) mg/dL, p&lt;0.05). No correlations between the level of Lp(a) and the concentration of PCSK9-Lp(a) complexes, nor between the level of Lp(a) or PCSK9 and the total number of monocytes were observed in both groups. A slight positive correlation between the concentration of PCSK9-Lp(a) complexes and the absolute level of monocytes was obtained (r=0.20, p=0.002) in patients with atherosclerosis predominantly due to intermediate monocyte subsets (r=0.33, p=0.04). According to regression analysis both PCSK9-Lp(a) complex concentration and BMI were related to the absolute number of blood monocytes in patients with atherosclerosis. Further studies are required to determine the pathogenetic contribution of PCSK9-Lp(a) complexes to the development of atherosclerosis.

Real time condition monitoring and precision health assessment system is a mandatory need for effective maintenance program in industrial sector. Rapid advancement in the information technology and other engineering technologies have invited more proactive attention from research and development in industrial sectors and particularly in condition monitoring of machines and related Industrial processes. In this work, drill bit condition monitoring techniques have been developed based on wavelet analysis and artificial neural networks (ANN) for automatic drill bit fault detection and classification. An experimental work has been conducted to capture the vibration signals for analysis. In this experiment, the CNC drill machine is used with high carbon steel drill bit and mild steel material as work piece. The cutting condition parameters are kept constant and the wear level is varied from 0.2 to 0.6 mm. The Data Acquisition system (DAQ) with Lab VIEW software is used to capture the vibration signals for drill bit with different wear conditions using accelerometer. The captured vibrations data are analyzed using continuous wavelet transform (CWT) with Morlet wavelet and Daubechies wavelet as a prime function. In general, the CWT coefficient is used to generate the inputs features to ANN for automatic tool condition classification, with two outputs (0, 1) for healthy and (1, 0) for faulty. The outcome of ANN showed 98% of accuracy in the wear prediction and this results show the effectiveness of the combed WT and ANN for automatic classification of tool wear conditions with high success rate.

The required processes and steps for making bread include technological and innovative concepts. The current trend is the use of less toxic compounds and green processes. Besides lactic acid bacteria and yeast, other microorganisms with special properties, such as enzymes, new aroma and flavor, exopolysaccharides, and vitamins, among other compounds with beneficial properties, could be added to bread manufacture, improving bread quality and health effects for the consumers. Freeze drying, new encapsulation methods, cryoprotectants, spray drying, fluidized bed drying, and vacuum drying are used for probiotics and microorganism cultures that will be used as starters or biological additives in the fermentation. The same development is observed in the preservation methods, and studies with plant extracts and essential oils have been proposed and introduced, replacing chemical agents, such as propionate, within the clean-label bread formulations concept. Baking science is a growing research line incorporating innovative methods and biological additives.

In recent years, solid state terahertz (THz) modulators have obtained rapid progress with the widespread use of two-dimensional (2D) materials in the field of THz; however, challenges remain in preparing flexible THz modulators. In this study, flexible ferromagnetic nematic materials were prepared by doping thermotropic nematic liquid crystals 5CB into magnetic fluids, and the influence of hydrogen bonding in water was reduced by a self-made cyclic olefin copolymer (COC) microfluidic chip. THz modulation characteristics of magnetic fluid and ferromagnetic nematic liquid crystal (FNLC) under the induction of external magnetic field were compared using a THz time domain spectroscopy system. Under the action of a 91 mT magnetic field, the magnetic fluid has a maximum modulation depth (MD) of 54%. Under the same magnetic field, the maximum MD of the ferromagnetic nematic liquid crystal materials increase to 78% because of the rearrangement of Fe3O4 nanoparticles induced by the topological defect of the liquid crystal. We demonstrate that the magneto-optical effect is significantly enhanced in the ferromagnetic nematic liquid crystal hybrid system. This strategy of doping thermotropic nematic liquid crystals to enhance the magneto-optical effect has great potential for THz filtering, modulation, and sensing applications.

Leptospirosis is a zoonotic disease of global importance. The current killed vaccine provides serovar-specific protection without sterilizing immunity. Several surface antigens, including Leptospira immunoglobulin-like proteins (LigA and LigB), have been identified as subunit vaccine candidates; however, they require potent adjuvants. Bacterial Lipopolysaccharide (LPS), including lipid A, is a well-known immunostimulatory agent, and the formulation of Monophosphoryl Lipid A (MPLA) in Alum is a clinical adjuvant. Being less endotoxic, we tested the adjuvant activity of lipid A purified from L. interrogans serovar Pomona (PLA) for its ability to activate innate and enhance antigen-specific adaptive immune response. PLA-induced activation of macrophages similar to levels induced by MPLA, albeit at a much higher dose, indicating that it is less stimulatory than MPLA. Mice immunized with a Variable portion of LigA (LAV) formulated in Alum and PLA (LAV-Alum-PLA) induced significantly higher levels of LAV-specific humoral and cellular immune response than Alum but similar to levels induced by Alum-MPLA. The adjuvant activity of PLA seems to be quite similar to MPLA and primarily mediated through enhanced recruitment, activation, and uptake of antigens by innate immune cells. Moreover, like MPLA, the PLA formulation was able to generate a long-term memory response. Most importantly, PLA demonstrated better potency than MPLA formulation and generated sterilizing immunity against challenge in a hamster model of leptospirosis. Altogether, our study has provided important insight into the adjuvant activity of Leptospira lipid A and has opened avenues for the development of LPS-based vaccines against this dreadful zoonosis.

We propose a novel moving median estimator specifically designed for online detection of threshold crossings in multi-channel signals, such as extracellular neural recordings. This estimator offers two key advantages: a reduced sensitivity to outliers and the elimination of memory requirements for storing arrival times. Furthermore, its design facilitates parallel implementation on FPGAs, making it ideal for real-time processing of multi-channel recordings.

The article attempts to place the research within the broader context of urban living labs (ULLs) and highlights the significance of understanding success criteria by gathering data from key stakeholders associated with Basaksehir Living Lab, Bodrum Living Lab and Mezopotamya Living Lab via the in-depth interview method. However, there is a literature gap in terms of a comprehensive understanding of the success criteria specific to ULLs, which hinders the effective utilization of ULLs as platforms for addressing urban challenges. The conclusions drawn from the article emphasize the need for further examination of these labs' openness, user empowerment, and transferability criteria. Nevertheless, the article contributes to understanding the success criteria of ULLs and provides insights for future research and practice.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

In machining, there is a constant effort to achieve the expected roughness of the machined surface while maintaining the life of the cutting tool during its operation. The methods used for extending machinability characteristics can be applied due to cooling and lubrication. One of the latest, but not new, targeted cooling techniques have become cryogenic treatment, which uses substances that exhibit extremely low-temperature values of about 123 K. This is a very environmentally friendly technique compared to the current standardized cooling and lubricating fluids. The main task of such cooling is to change the properties of the workpiece so that it exhibits the properties of a brittle material. Bringing the workpiece structure in this way can result in easier material separation through the chip. In the article, the obtained test results can approximate the behavior of various materials during cryogenic cooling.

Electric torque wrenches play a crucial role in the assembly of high-strength bolts. This study focuses on three assembly processes for high-strength bolts and introduces a statistical analysis method to assess the quality of the bolt assembly. To enhance the performance, a novel, fully digital, Internet of Things (IoT) electric torque wrench is designed, incorporating a smart meter chip. This wrench achieves integration between the current sensor control method and the torque sensor control method using a simplified hardware circuit, ensuring high precision and stability. Additionally, this study employs the AC voltage self-stabilization method and Savitzky–Golay filtering method to enhance the accuracy and robustness of the wrench. Simulation experiments using Simulink and Matlab validate the effectiveness of these two methods. Furthermore, a cloud platform is utilized to enable rapid IoT access for the wrench, facilitating seamless connectivity and data transmission.

This study investigated novel quantitative traits loci (QTLs) associated with the control of grain shape and size as well as grain weight in rice. We employed a joint strategy multiple GAPIT (Genome Association and Prediction Integrated Tool) models [(Bayesian-information and Linkage-disequilibrium Iteratively Nested Keyway (BLINK)), Fixed and random model Circulating Probability Uniform (FarmCPU), Settlement of MLM Under Progressive Exclusive Relationship (SUPER), and General Linear Model (GLM)]–High Density SNP Chip DNA Markers (60,461) to conduct a Genome-Wide Association Study (GWAS). GWAS was performed using genotype and grain-related phenotypes of 143 recombinant inbred lines (RILs). Data show that parental lines (Ilpum and Tung Tin Wan Hein 1, TTWH1, Oryza sativa L., ssp. japonica and indica, respectively) exhibited divergent phenotypes for all analyzed grain traits), which was reflected in their derived population. GWAS results revealed the association between seven SNP Chip makers and quantitative trait loci (QTLs) for grain length, co-detected by all GAPIT models on (Chr) 1–3, 5, 7, and 11), were qGL1-1BFSG (AX-95918134, Chr1: 3820526 bp) explains 65.2%–72.5% of the phenotypic variance explained (PVE). In addition, qGW1-1BFSG (AX-273945773, Chr1: 5623288 bp) for grain width explains 15.5%–18.9% of PVE. Furthermore, BLINK or FarmCPU identified three QTLs for grain thickness independently, and explain 74.9% (qGT1Blink, AX-279261704, Chr1: 18023142 bp) and 54.9% (qGT2-1Farm, AX-154787777, Chr2: AX-154787777 bp) of the observed PVE. For t length-to-width ratio, the qLWR2BFSG (AX-274833045, Chr2: 10000097 bp) explains nearly 15.2%–32% of PVE for LWR. Likewise, the major QTL for thousand-grain weight (TGW) was detected on Chr6 (qTGW6BFSG, AX-115737727, 28484619 bp) and explains 32.8%–54% of PVE. The qTGW6BFSG QTL coincides with qGW6-1Blink for grain width and explained 32.8%–54% of PVE. Putative Candidate genes pooled from major QTLs for each grain traits have interesting annotated functions that require functional studies to elucidate their function in the control of grain size, shape, or weight in rice. Genome selection analysis proposed makers useful for downstream marker-assisted selection based on genetic merit of RILs.

In Escherichia coli, DNA replication termination is orchestrated by two clusters of Ter sites forming a DNA replication fork trap when bound by Tus proteins. The formation of a ‘locked’ Tus-Ter complex is essential for halting incoming DNA replication forks. However, the absence of replication fork arrest at some Ter sites raised questions about their significance. In this study, we examined the genome-wide distribution of Tus and found that only the six innermost Ter sites (TerA-E and G) were significantly bound by Tus. We also found that a single ectopic insertion of TerB in its non-permissive orientation could not be achieved, advocating against a need for ‘back-up’ Ter sites. Finally, examination of the genomes of a variety of Enterobacterales revealed a new replication fork trap architecture mostly found outside the Enterobacteriaceae family. Taken together, our data enabled the delineation of a narrow ancestral Tus-dependent DNA replication fork trap consisting of only two Ter sites.

Plant life-long organogenesis involves sequential, time and tissue specific expression of developmental genes. This requires activities of Polycomb Group (PcG) and trithorax Group complexes, respectively responsible for repressive Histone 3 trimethylation at lysine 27 (H3K27me3) and activation-related H3K4me3. However, the genome-wide dynamics in histone modifications that occur during developmental processes have remained elusive. Here, we report the distributions of H3K27me3 and H3K4me3 along with transcriptional changes, in a developmental series including Arabidopsis leaf and three stages of flower development. We found that chromatin mark levels are highly dynamic over the time series on nearly half of all Arabidopsis genes. Moreover, during early flower morphogenesis, changes in H3K4me3 prime over changes in H3K27me3 and quantitatively correlate with transcription changes, while H3K27me3 changes occur after prolonged expression changes. Notably, early activation of PcG target genes is dominated by increases in H3K4me3 while H3K27me3 remains present at the locus. Our results reveal H3K4me3 as greater predictor over H3K27me3 for transcription dynamics, unveil unexpected chromatin mechanisms at gene activation and underline the relevance of tissue-specific temporal epigenomics.

The objective of the this study was to reduce the benzo[a]pyrene-induced hepatotoxicity method in herbal medicine products and to give proof that neferine, daidzein, genistein possess antihepa-totoxic effects. B[a]P which classified as a group 1 carcinogen and metabolized to B[a]P-7,8-dihydrodiol-9,10-epoxide (BPDE) causes mutagenic DNA addition products. The reduc-tion of BPDE-DNA adduct formation by B[a]P-7,8-dihydrodiol-9,10-epoxide (BPDE) was derived by benzo[a]pyrene (B[a]P). In HepG2 cells, B[a]P exhibited toxicity and substance treatment of the cells with B[a]P with neferine in lotus and daidzein, genistein in soybean reduced the BPDE-DNA ad-ducts level. The level of B[a]P-metabolites in the substance treatment of the cells was presented that BPDE levels were reduced by neferine in lotus and daidzein, genisten in soybean. These results suggest that neferine in lotus and daidzein, genistein in soybean prevent B[a]P-induced hepato-toxicity for BPDE-DNA adduct formation.

In this paper we investigate analytic automorphisms of complex topological vector spaces and their applications to linear and nonlinear transitive operators. We constructed some examples of polynomial automorphisms which show that a natural analogue of the Jacobian Conjecture for infinite dimensional spaces is not true. Also, we prove that any separable Fréchet space supports a transitive analytic operator which is not a polynomial. We found some connections of analytic automorphisms and algebraic bases of symmetric polynomials and applications to hypercyclisity of composition operators.

Despite the development of biorefinery processes, so far this area does not take into account the possibility of coupling the “conventional” composting process with the production of biochemicals. However, net carbon monoxide (CO) production has been observed during bio-waste composting. So far, O2 concentration and temperature have been identified as main variables influencing CO formation. This study aimed to investigate the CO net production during bio-waste composting under controlled laboratory conditions, depending on different aeration rates and temperatures. A series of composting processes were carried out in conditions ranging from ~psychrophilic to thermophilic (T=35, 45, 55, and 65°C) and an aeration rate of 2.7, 3.4, 4.8, and 7.8 L‧h-1. The highest concentrations of CO in each thermal variant was achieved with oxygen deficit (aeration rate 2.7 L‧h-1); additionally, CO levels increased with temperature, reaching ~300 ppm at 65°C. Production of CO in mesophilic and thermophilic conditions draws attention to the biological CO formation by microorganisms capable of producing the CODH enzyme. Further research on the CO production efficiency in these thermal ranges is necessary with the characterization of the microbial community and analysis of the ability of the identified bacteria to produce the CODH enzyme and convert CO from CO2.

Federated learning (FL) has emerged as a crucial technology in today’s data-centric technological environment, enabling decentralized machine learning and safeguarding user privacy. This study introduces “Federated Operations (FedOps) Mobile,” a novel FL framework optimized for the dynamic and heterogeneous ecosystem of mobile devices. FedOps Mobile enhances traditional FL approaches for mobile devices by integrating real-time operational control and advanced on-device training capabilities using TensorFlow Lite and CoreML, addressing critical challenges in scalability, efficiency, and system heterogeneity. Our approach utilizes a wide range of devices, facilitated by intelligent client-selection mechanisms. This mechanism evaluates the capabilities and readiness of multiple devices per client to ensure fair and efficient network participation. The framework also utilizes remote device control for seamless task management and sustained engagement, enabling continuous learning without compromising the user experience. We conducted extensive experiments to validate the framework’s performance, focusing on three core aspects: operational efficiency, model personalization, and resource optimization in multi-device environments. The results demonstrate that the proposed method is effective for efficient client selection, energy consumption, and model optimization.

This research paper contributes to the literature of deterrence theory in general, and in particular with respect to white-collar crime, offering valuable inside by using a unique data set of fraud and violation of trust incidents for Paraguay. Descriptive evidence show a clear and continuous misallocation of funds and human capital, and therefore providing less efficient services for the public. Regression analysis suggests that clearance rate exerts a highly significant effect in deterring fraud but results are not clear for violation of trust incidents. Despite the limitations of available data, results confirm deterrence theory in Paraguay. However, to more than two-thirds of victims, not even the attempt was made to seek justice. As a side-result, it seems that a soft on crime strategy, induced from the former German penal code, has led to an increasing share of pre-trial diversion and therefore enhancing white-collar crimes like fraud and violation of trust due to impunity.

Biometric based access control system acts as a weapon against the challenges for reliable authentication mechanism. Although there are many advantages of biometric system, still it is vulnerable to attacks, which decline its security. This leads to propose a new approach to address these open issues and challenges for biometric data security. Smart card have been already used in past with various degree of success to store biometric credentials. Match-on-card biometric framework locks the biometric data inside the microcontroller of the smart card, which leads to minimal risks if card is lost or stolen. It is fast and accurate, balancing security and convenience by never exchanging user data outside the system of smart card and performs fingerprint enrollment as well as matching within a tamperproof environment of smart card.

Molecules sourced from marine environments hold immense promise for the development of novel therapeutic drugs, owing to their distinctive chemical compositions and valuable medicinal attributes. Notably, Talarolide A and Talaropeptides A-D have gained recent attention as potential candidates for pharmaceutical applications. This study aims to explore the chemical reactivity of Talarolide A and Talaropeptides A-D through the application of molecular modeling and computational chemistry techniques, specifically employing Conceptual Density Functional Theory (CDFT). By investigating their chemical behaviors, the study seeks to contribute to the understanding of the potential pharmacological uses of these marine-derived compounds. The investigation involves the utilization of molecular modeling and computational chemistry tools, with a specific focus on Conceptual DFT. These techniques are applied to examine the chemical reactivity of Talarolide A and Talaropeptides A-D, shedding light on their potential for interacting with various biological targets. The research reveals insights into the chemical reactivity of Talarolide A and Talaropeptides A-D, uncovering active reaction sites and potential biological targets. Talarolide A demonstrates robust anti-inflammatory properties and antitumor activity against diverse cancer cell lines, while Talaropeptide A displays antimicrobial efficacy against both bacteria and fungi. The study underscores the significance of comprehending the chemical reactivity of natural marine products for advancing pharmaceutical development. By employing computational tools such as Conceptual DFT, this research uncovers crucial information about the active sites and potential targets of Talarolide A and Talaropeptides A-D. The findings contribute to the broader understanding of marine-derived peptides and their prospects as pharmaceutical agents, though further investigations are necessary to fully elucidate their pharmacological attributes.

Several biomedical products, like scaffolds, implants, prostheses, and orthoses, require materials having superior physicochemical and biological properties. Polyethylene terephthalate glycol (PETG) is being increasingly used for various biomedical applications. There are a few studies on PETG-based composites, however, natural fibers like silk short fibers reinfored PETG composites have not been attempted. Being a cost-effective widely available material, PETG-Silk combination can be potential biocomposite for several biomedical applications. Here, we report a novel short silk fiber reinforced PETG composite prepared by a wet-mixing route, ensuring homogenous dispersion of the filler. Different ratios (2-10%) of short silk fibers were used to prepare composites with varied compositions. The mechanical, physicochemical, and biological properties of the prepared composites were analyzed. Thermogravimetric analysis showed that such composites are thermally stable up to 390 °C and can be used for thermal extrusion-based manufacturing. The tensile modulus of the samples increased with fiber content; however, the failure strain reduced with fiber content. Furthermore, upon annealing, the tensile modulus increased but, the failure strain of the composites decreased, XRD study revealed that heat treatment has altered the crystalline nature of the composites. Finally, we evaluated the cytocompatibility of the prepared composites to assess their suitability for various biomedical applications.

Gene regulation is vital for cellular function and homeostasis, involving diverse mechanisms controlling specific gene products and contributing to tissue-specific gene expression. Dysregulation leads to diseases, emphasizing the need for understanding these mechanisms. Non-coding regions, notably enhancers and super-enhancers (SEs), act as crucial gene regulators, orchestrating transcriptional activity via transcription factors (TFs). SEs, with high activity, are pivotal in cell identity and disease progression. Current computational approaches focus on individual regulators like TFs and miRNAs, neglecting SE interactions. We emphasize incorporating SEs into models to enhance understanding. Experimental studies have recently linked miRNAs and TFs to SEs. Chromatin immunoprecipitation followed by sequencing (ChIP-Seq) provides valuable SE information. In this review, we categorize computational methods leveraging TF and miRNA data into three areas and explore challenges integrating enhancers/SEs. These include unraveling indirect regulatory networks, identifying network motifs, and enriching pathway identification by dissecting gene regulators, including SEs. We hypothesize that addressing these challenges will enhance our understanding of gene regulation, aiding in identifying therapeutic targets and disease biomarkers. We believe that understanding the role of ChIP-Seq data in predicting the effect of miRNA on gene regulation is crucial to construct statistical/computational model that would tackle these challenges.

The experiments described in this research article were designed to test the effect of rare variants into genomic prediction in dairy cattle. Common polymorphisms are able to explain only a small proportion of the underlying genetic variation of complex phenotypes. Variants representing functional mutations with large effects on complex phenotypes are expected to be rare due to natural (humans) or artificial (livestock) selection pressure. Therefore, it is important to check whether the use of rare variants could increase the accuracy of ranking of animals by providing the tool for more precise differentiation among the bulls with high additive genetic merit. The goal of our study was to verify whether including rare variants in a genomic selection model allows for a more accurate description of the additive genetic background of traits under selection in dairy cattle. We used the linear mixed model for comparison SNP estimates for Holstein-Friesian cattle of the two data sets – a set containing only single nucleotide polymorphisms defined by minor allele frequency ≥ 0.01, which is routinely used in the Polish genomic evaluation system (46,216 SNPs), and a set containing SNPs selected based only on the call rate (54,378 SNPs). Based on the SNP estimates we also calculated DGV and GEBV and compared them between both data sets. In all the analyses we used production, fertility, conformation and udder health traits. We also assessed the time required for the two most computationally demanding components of genomic selection: preparing genotype data, and estimation of SNP effects between those two data sets. The results of our study indicated that the analysis including rare variants resulted in changes in the individual ranking of the top 100 male and female candidates, but had no effect on the outcome of the quality of EBV prediction as expressed by the Interbull validation test.

Smart, reliable, and connected multi-modal mobility has been a long-standing goal of transit services. This paper focuses on the smart, seamless, and multi-modal mobility service in the context of “Mobility as a Service” (MaaS). Intelligent mobility is the smarter, greener, and more efficient movement of passengers around the world. Increasingly, mobility is approached as a service. This study first conducts an extensive literature review on mobility behavior and demand pattern of MaaS end-users. It then extends the mechanism of supply chain, MaaS, synergy (i.e., vertical cooperation synergy, horizontal competition synergy), and coopetition to develop the multi-tier closed-loop intelligent mobility service supply chain network. This paper explains the intelligent mobility service supply chain network from following perspectives: (i) mobility service taxonomy of MaaS; (ii) aims of intelligent mobility service supply chain network; (iii) urban rail transit (URT)-centered alternatives for integrated multimodal journey planning, i.e. access + URT + egress, and both access and egress can be served by Mobility-On-Demand (MOD) transport; (iv) node member imperatives. From a synthesis of insights from the ‘during’ journey, this study puts forward the synergetic design of intelligent mobility service supply chain network, including: (i) multi-tier closed-loop structure; (ii) key nodes identification for the physical multimodal transport network in the supply chain; (iii) hybrid synergy mechanisms among the partners, i.e., synergy principle, temporal splitting approach for coopetition synergy; (iv) index systems and evaluation methods for synergy measurement. This study also contributes to the integrated multimodal journey planning. In concluding, the paper highlights the important implications of the proposed intelligent mobility service supply chain network for MaaS bundle design and adverse effects reduction, resulting from 1 + 1 > 2 synergy effects.

This study presents a transversal investigation, that we performed at Fundeni hospital, into the therapeutic benefits and efficacy of Emicizumab, a non-factor therapy, in the context of hemophilia A. Ten patients diagnosed with hemophilia A were closely monitored, using clinical and laboratory resources, during the course of Emicizumab treatment, with an average of 12.8 months. Among these patients, six exhibited anti-factor VIII inhibitors, changing the medical approach and adding complexity to their clinical profiles. A comprehensive approach was adopted to assess the coagulation status of patients under Emicizumab therapy. The study employed several key coagulation monitoring tools, of which including thrombin generation time (TGT) and thrombelastography (TEG). These methodologies proved highly valuable results in evaluating the patients' coagulation profiles during the treatment regimen. Additionally, traditionally coagulation assays were utilized to gain a comprehensive understanding of the overall coagulation dynamics. Noteworthy, impressive outcomes emerged from the study. During prophylaxis with Emicizumab all patients had experienced a reduced number of bleeding events. Moreover, a subset of these patients underwent major surgical procedures (orthopedic joint replacements) with successful outcomes. These findings underscore the potential of Emicizumab therapy as an effective option for hemophilia A patients, including those that presented a prompt production of anti-factor VIII inhibitors. As for the outcomes, this transversal study sheds some light on the positive impact of Emicizumab therapy in addressing the coagulation challenges posed by hemophilia A. The utilization of global coagulation assays, such as thrombin generation time, thrombelastography and combined with traditional coagulation assays, used as monitoring tools highlights their significance once more in evaluating the therapeutic response. This research contributes by providing physicians with valuable insights to the field, offering a potential avenue for improved patients’ care and treatment strategies that translate in enhanced quality of life for hemophilia A patients undergoing Emicizumab therapy.

The purpose of this study is to explore the effect of Environment, Social, and Governance (ESG) scores on Return on Assets (ROA), Risk-Adjusted Return on Capital (RAROC), and Tobin's Q on firm performance. This study used 37 non-financial companies listed on the IDX between 2018 and 2022 in Indonesia companies. Linear and nonlinear panel data regression methods were used on the ESG score and its pillars, resulting in eight different models. The study found a U-shaped impact of ESG scores and social and environmental pillars on ROA. There is a positive linear relationship between ESG scores and the environmental and governance pillars with RAROC, while the social pillar shows an inverted U-shaped effect. However, ESG and its environmental and social pillars have a negative linear relationship with Tobin's Q. The findings suggest the need to manage ESG initiatives strategically, aligning them with financial objectives and awareness of how ESG factors relate to profitability.

This article systematically studied the A-optimal designs of a high-order mixture central polynomial model, which is an advancement of the research results for the A-optimal design of the most recent third-order mixture central polynomial model and a more accurate response surface model. This article is based on the simplex center design, obtaining measurement values at various design points, and verifying them through the A-optimal equivalence theorem. We also compare the A-efficiency of designs through examples, which can be applied to the A-optimal precise design of the fourth-order mixture model.

Traumatic brain injury (TBI) is a major leading cause of death and disability. While previous studies regarding focal pathologies following TBI have been done, there is a lack of information concerning the role of analgesics and their influences on injury pathology. Buprenorphine (Bup), an opioid analgesic, is a commonly used analgesic in experimental TBI models. Our previous studies investigated the acute effects of Buprenorphine-sustained release-Lab (Bup-SR-Lab) on diffuse neuronal/glial pathology, neuroinflammation, cell damage, and systemic physiology. The current study investigated the longer-term chronic outcomes of Bup-SR-Lab treatment at 4 weeks following TBI utilizing a central fluid percussion injury (cFPI) model in adult male rats. Histological assessments of physiological changes, neuronal damage, cortical and thalamic cytokine expression, microglial and astrocyte morphological changes, and myelin alterations were done, as we had done in our acute study. In the current study the Whisker Nuisance Task (WNT) was also performed pre- and 4w post-injury to assess changes in somatosensory sensitivity following saline or Bup-SR-Lab treatment. Bup-SR-Lab treatment had no impact on overall physiology or neuronal damage at 4w post-injury regardless of region or injury, nor did it have any significant effects on somatosensory sensitivity. However, greater IL-4 cytokine expression with Bup-SR-Lab treatment was observed compared to saline treated animals. Microglia and astrocytes also demonstrated region-specific morphological alterations associated with Bup-SR-Lab treatment, in which cortical microglia and thalamic astrocytes were particularly vulnerable to Bup-mediated changes. There were discernable injury-specific and region-specific differences regarding myelin integrity and changes in specific myelin basic protein (MBP) isoform expression following Bup-SR-Lab treatment. This study indicates that use of Bup-SR-Lab could impact TBI-induced glial alterations in a region-specific manor 4w following diffuse brain injury.

Achieving global goals on sustainable nutrition, health, and wellbeing will depend on delivering enhanced diets to humankind. This will require, among others, instantaneous access to information on food quality at key points within agri-food systems. Although stationary methods are usually used to quantify grain quality (wet-lab chemistry, benchtop NIR spectrometer); these do not suit many required user-cases, such as stakeholders in decentralized agri-food-chains that are typical for emerging economies. Therefore, we explored new technologies and models that might aid these particular user-cases. For this purpose, we generated the NIR spectra of 328 grain samples from multiple cereals (finger millet, foxtail millet, maize, pearl millet, sorghum) with a standard benchtop NIR Spectrometer (DS2500, FOSS) and a novel mobile NIR-based sensor (HL-EVT5, Hone). We explored a range of classical deterministic and novel machine learning (ML)-driven models to build calibrations out of the NIR spectra. We were able to build relevant calibrations out of both types of spectra. At the same time, ML-based methods enhanced the prediction capacity of calibration models compared to classical deterministic methods. We also documented that the prediction of grain protein content based on NIR spectra generated by a mobile sensor (HL-EVT5, Hone) was highly relevant for quantitative protein predictions (R2 = 0.91, RMSE = 0.97, RPD = 3.48). Thus, the findings of this study lay the foundations on which to expand the utilization of NIR spectroscopy applications for agricultural research and development.

This research aimed to discover how to create a customer experience that includes FEEL, SENSE, THINK, ACT, and RELATE to increase satisfaction with the Subscription Video on Demand (SVoD) application. A descriptive quantitative method was used, and the sample was 423 respondents in Indonesia who had used the application for at least 1 month. Furthermore, this research used probability sampling using a technique for random sampling. Based on the data available, experience accounted for 0.509, or 50.9%, of the application satisfaction. With a beta value of 0.295, the FEEL variable was the only one in this study to significantly and positively affect customer satisfaction; the other variables, SENSE, THINK, ACT, and RELATE, had no discernible effects. It is anticipated that the theoretical foundation provided by this research will be beneficial to the entertainment industry, particularly the SVoD application sector. This includes the product and service development division that focuses on customer inner feelings and emotions.

Worldwide, among older adults, infection is the leading mortality cause; chronic nutritional deficits confer significant mortality risk and increase healthcare costs. The association of the Global Leadership Initiative on Malnutrition (GLIM)-defined malnutrition with infection-related mortality, especially with renal dysfunction in older patients, remains unevaluated. In older patients hospitalized with infection, stratified by renal function, we investigated the association of malnutrition severity with mortality. This single-center, retrospective cohort study of 1220 participants (age ≥65 years) admitted to Aichi Medical University from 2019 to 2020 used a multivariate Cox proportional hazards model to determine the association of GLIM-defined nutritional status (no, moderate, or severe malnutrition) with all-cause mortality. Compared to no malnutrition, moderate and severe malnutrition conferred significantly higher mortality (adjusted hazard ratio [confidence interval ]: 1.00 [reference], 1.76 [1.28-2.42], and 2.44 [1.78-3.33], respectively), with the highest all-cause mortality in malnutrition with a low estimated glomerular filtration rate (eGFR &lt;30 mL/min/1.73m2; 7.35 [4.57-11.8]) compared to no malnutrition and normal eGFR (≥60 mL/min/1.73m2). GLIM-defined malnutrition confers higher all-cause mortality risk in older adults with infection, especially those with renal dysfunction. This information enables the identification of high-risk older patients with infection and targeted clinical management of those with malnutrition, renal dysfunction, and infection.

Oncological changes in the prostate are a common cause of death among elderly men. Malignant cells are difficult to identify at early stages, which are asymptomatic. The patient often seeks medical assistance when the disease has already progressed, and the treatment is less effective. Early diagnosis of prostate cancer (PC) is thus one of the priority tasks of modern urology and healthcare in general. The aim of this study is the detection of microRNAs (miRNAs), which are known to be associated with PC. The detection of the target miRNAs in human plasma samples has been performed with a nanoribbon biosensor system, which was based on "silicon-on-insulator" structures (SOI-NR biosensor). In order to provide biospecific detection of the target miRNAs, the surface of individual nanoribbons has been modified with DNA oligonucleotide probes (oDNA probes), whose nucleotide sequences were complementary to those of the target miRNAs. The high detection sensitivity has been demonstrated with the use of model oDNAs, which are complementary to nanoribbon-immobilized oDNA probes, in buffer solutions. The sensitivity threshold was 1.1 × 10^-17 M. The successful detection of target miRNAs, isolated from real plasma samples of PC patients, has also been demonstrated. We believe that the development of highly sensitive nanotechnology-based biosensors for PC markers is a step towards personalized medicine.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

This paper aims to describe the geometrical structure and explicit expressions of family of finitely parametrized probability densities over smooth manifold $M$. The geometry of family of probability densities on $M$ are inherited from probability densities on Euclidean spaces $\left\{U_\alpha \right\}$ via bundle morphisms, induced by an orientation-preserving diffeomorphisms $\rho_\alpha:U_\alpha \rightarrow M$. Current literature inherits densities on $M$ from tangent spaces via Riemannian exponential map $\exp: T_x M \rightarrow M$; densities on $M$ are defined locally on region where the exponential map is a diffeomorphism. We generalize this approach with an arbitrary orientation-preserving bundle morphism; we show that the dualistic geometry of family of densities on $U_\alpha$ can be inherited to family of densities on $M$. Furthermore, we provide explicit expressions for parametrized probability densities on $\rho_\alpha(U_\alpha) \subset M$. Finally, using the component densities on $\rho_\alpha(U_\alpha)$, we construct parametrized mixture densities on totally bounded subsets of $M$. We provide a description of inherited mixture product dualistic geometry of the family of mixture densities.

In this paper, I investigate Hyers-Ulam-Rassias stabilities of the general quintic functional equation and the general sextic functional equation.

Polymerase chain reaction (PCR) technique is one of the molecular methods in amplifying DNA for the detection of malaria. However, the limitations of PCR especially when used for routine clinical practice can hamper its sensitivity and specificity. With that, this study focuses on designing a microfluidic device that will mimic the function of a conventional genus-specific PCR based on 18S rRNA gene to detect malaria parasites (Plasmodium falciparum) at low grade parasitemia. The design was drawn and simulated using ANSYS 14.5 Computational Fluid Dynamics (CFD). The simulation shows that adding loops to the design increases its relative deviation but to a minimal extent as compared to having only a straight path design, which indicates that looping is acceptable in designing a microfluidic device to minimize chip length. Also, increasing the cross-sectional area of the fluid path decreases the efficiency of the design, thus, the design with a relatively smaller cross-sectional area is favored. And lastly, among the three materials utilized, the chip made of polypropylene is the most efficient with a relative deviation of 0.94 as compared to polycarbonate and polydimethylsiloxane which have relative deviations of 2.78 and 1.92, respectively.

The market for microfluidic chips is experiencing significant growth; however, their development is hindered by a complex design process and low efficiency. Enhancing microfluidic chips’ design quality and efficiency has emerged as an integral approach to foster their advancement. Currently, the existing structural design schemes lack careful consideration regarding the impact of chip area, microchannel length, and the number of intersections on chip design. This inadequacy leads to redundant chip structures resulting from the separation of layout and wiring design. This study proposes a structural optimization method for microfluidic chips to address these issues utilizing a simulated annealing algorithm. The simulated annealing algorithm generates an initial solution in advance using the fast sequence pair algorithm. Subsequently, an improved simulated annealing algorithm is employed to obtain the optimal solution for the device layout. During the wiring stage, an advanced wiring method is used to designate the high wiring area, thereby increasing the success rate of microfluidic chip wiring. Furthermore, the connection between layout and routing is reinforced through an improved layout adjustment method, which reduces the length of microchannels and the number of intersections. Finally, the effectiveness of the structural optimization approach is validated through six sets of test cases, successfully achieving the objective of enhancing the design quality of microfluidic chips.

The motivation for investigating the issues presented in this article stemmed from a need to understand better the relationship in long-established physics formulas and extract the information they provided using conventional methods. Based on the definition of magnetic flux quantization, which is based on a combination of fundamental physical constants, the Planck constant, and the particle’s elementary charge, this work explores the results that arise when this equation is combined with the equation of the Bohr-level electrostatic force acting on the electron, which leads to a new mathematical relationship between the combined expressions. The new relationship yields novel theoretical findings related to the known universal constants. Following this insight, the formalism developed in this paper indicates that the mass of the electron and other subatomic particles is associated with the magnitude of the square of the magnetic flux quantum, which makes up the particle. This conclusion is not as strange as it may seem, as the square of the magnetic flux quantum appears in the context of magnetic energy in a current loop and, according to Einstein’s special theory of relativity, energy is equivalent to mass. Another aspect described at the end of this paper demonstrates the connection between the square of the magnetic flux quantum through the Bohr radius and the significance of the wave function in the atom. The theoretical results are in full accordance with experimental results published by NIST CODATA 2018 that I’ve used, which validates the existence of the relationship.

The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

In the field of robotics education, introductory courses would ideally utilize heavy industrial arms for hands-on learning. This would provide students with valuable experience in joint programming, which involves direct control of each joint motor in the arm to accomplish desired path planning and differential movements. This practice requires consideration of the physical dynamics of the arm. However, the use of heavy industrial arms has several drawbacks. They are large and expensive, require specialized maintenance, can pose safety risks, and they typically do not allow for direct control of the joint motors. One solution is to use a small, lightweight, toy-like arm. While these are cost-effective and provide direct access to the joint motors without posing safety risks, their lightweight construction means they exhibit minimal dynamic behavior, which limits their educational value. Another solution involves a robotic arm simulator that uses a virtual arm. However, a virtual arm doesn't offer the same level of hands-on engagement and excitement as a physical arm. We propose a hybrid solution that combines a small physical arm with a virtual arm. This approach provides students with the experience of working with an industrial arm, but without the associated difficulties. We demonstrate how this approach successfully improved the completion rate of joint programming assignments, offering a promising solution for practical robotics education.

(1) Background: The purpose of this study is to evaluate the full arch scan accuracy (precision and trueness) of nine digital intra-oral scanners and four lab scanners. Previous studies have compared the accuracy of some intra-oral scanners, but as this is a field of quickly developing technologies, a more up-to-date study was needed to assess the capabilities of currently available models.; (2) Methods: The present in vitro study compared nine different intraoral scanners (Omnicam 4.6; Omnicam 5.1; Primescan; CS 3600; Trios 3; Trios 4; Runyes; i500 and DL206) as well as four lab light scanners (Einscan SE; 300e; E2 and Ineos X5) to investigate the accuracy of each scanner by examining the overall trueness and precision. Ten aligned and cut scans from each of the intra-oral and lab scanners in the in vitro study were brought into CloudCompare. A comparison was made with the master STL using the CloudCompare 3D analysis best-fit algorithm. The results were recorded along with individual standard deviation and a colorimetric map of the deviation across the surface of the STL mesh; a comparison was made to the master STL, quantified at specific points. ; (3) Results: In the present study, the Primescan had the best overall trueness (17.3 ± 4.9). Followed by (in order of increasing deviation) the Trios 4 (20.8 ± 6.2), i500 (25.2 ± 7.3), CS3600 (26.9 ± 15.9), Trios 3 (27.7 ± 6.8), Runyes (47.2 ± 5.4), Omnicam 5.1 (55.1 ± 9.5), Omnicam 4.6 (57.5 ± 3.2) and Launca DL206 (58.5 ± 22.0). Regarding the lab light scanners, the Ineos X5 had the best overall trueness with (0.0 ± 1.9). Followed by (in order of increasing deviation) the 3Shape E2 (3.6 ± 2.2), Up3D 300E (12.8 ± 2.7), and Einscan SE (14.9 ± 9.5); (4) Conclusions: This study confirms that all current generations of intra-oral digital scanners can capture a reliable, reproducible full arch scan in dentate patients. Out of the intra-oral scanners tested, no scanner produced results significantly similar in trueness to the Ineos X5. However, the Primescan was the only one to be statistically of a similar level of trueness to the 3Shape E2 lab scanner. All scanners in the study had mean trueness of under 60-micron deviation. While this study can compare the scanning accuracy of this sample in a dentate arch, the scanning of a fully edentulous arch is more challenging. The accuracy of these scanners in edentulous cases should be examined in further studies.

Surfactant proteins A and D (SP-A and SP-D) belong to the collectin subfamily of C-type oligomeric lectins. They are pattern-recognition molecules (PRM), able to recognise pathogen- or dan-ger-associated molecular patterns (PAMP, DAMP) in the presence of Ca2+ cations. That property enables opsonisation or agglutination of non-self or altered/abnormal self-cells, and contributes to their clearance. Like other collectins, SP-A and SP-D are characterised by the presence of four distinct domains: a cysteine-rich domain (at N-terminus), a collagen-like region, an α-helical neck domain and a globular carbohydrate-recognition domain (CRD) (at C-terminus). Pulmonary sur-factant is a lipoprotein complex, preventing alveolar collapse by reducing surface tension at the air-liquid interface. SP-A and SP-D, produced by type II alveolar epithelial cells, and Clara cells, are not only pattern-recognition molecules but also contribute to the surfactant structure and homeo-stasis. Moreover, they are expressed in a variety of extrapulmonary sites where they are involved in local immunity. The term “cancer” includes a variety of diseases: tumours start from uncontrolled growth of abnormal cells in any tissue which may further spread to other sites of the body. Many cancers are incurable, difficult to diagnose and often fatal. This short review summarises anti- and pro-tumourigenic associations of SP-A and SP-D as well as perspectives of their usefulness in cancer diagnosis and therapy.

An efficient approach to the previously unknown furo[2',3':2,3]pyrrolo[2,1-a]isoquinoline deriv-atives from readily available 1-R-1-ethynyl-2-vinylisoquinolines is described. The reaction fea-tures a simple procedure, occurs in hexaflouroisopropanol and does not require elevated tem-peratures. It has been found that the addition of glacial acetic acid significantly increases the yields of the target spirolactone products. Using trifluoroethanol instead of hexaflouroisopro-panol results into formation of pyrido[2,1-a]isoquinolines.

Here we report a comparative study of the pyhtochemical profile and a biological activity of the two onion extracts, namely A. cepa L. and A. × cornutum (Clementi ex Visiani 1842). Identification of flavonoids and anthocyanins and their individual quantities were determined by high performance liquid chromatography (HPLC). The potency of both extracts to scavenge free radicals was determined by DPPH (2,2'-diphenyl-1-picrylhydrazyl) radical-scavenging activity and oxygen radical absorbance capacity (ORAC) methods. DNA protective role was further tested by single-cell gel electrophoresis (COMET) assay and by Fenton’s reagent causing double strand brakes on pUC19 plasmid. In the presence of both extracts, a significant decrease in the DNA damage was observed, which indicates a protective role of A. cepa and A. × cornutum on the DNA strand brakes. Additionally, cytotoxicity was tested on glioblastoma and breast cancer cell lines. The results showed that both extracts had antiproliferative effect, but the most prominent decrease in cellular growth was observed with glioblastoma cells

In recent times, the adoption of cloud computing by small and medium-sized 9 enterprises (SMEs) has become a crucial issue. These businesses face substantial difficulties in 10 accessing reliable and affordable IT infrastructure due to economic constraints and technological 11 restrictions. Hybrid cloud computing solutions which incorporate Infrastructure as a Service 12 (IaaS), Platform as a Service (PaaS), and Software as a Service (SaaS) offer a feasible approach to 13overcoming these challenges. This study proposes a systematic literature review of cloud 14 computing's impact on SME performance emphasizing cost-efficiency, reliability, and 15 competitive advantages, using the 2020 Preferred Reporting Items for Systematic Reviews and 16 Meta-Analyses (PRISMA) framework. The inclusion criteria are bounded by (1) publication date 17 between 2014 and 2024, (2) English-language publications, (3) research focused on cloud 18 computing for SMEs, and (4) studies with a clear analytical framework for evaluating SME 19 performance. Following this process, 90 eligible research studies were included. The average 20 total cost for cloud services varies significantly, with operational costs reflecting the scalability 21 of the services and the specific needs of SMEs. This analysis offers valuable guidance for SMEs 22 and stakeholders in optimizing cloud-based strategies for enhanced performance.

Background:Patients with chronic kidney disease (CKD), especially those undergoing dialysis, encounter complex nutritional challenges. Key dietary factors such as protein and fluid intake, potassium and sodium levels, and co-morbidities significantly influence dietary planning for CKD patients. A standardized approach to dietary recommendations for CKD patients is ineffective due to the diverse needs of individual patients. Social media platforms have become a popular source of dietary information, often advocating low-carb, high-protein diets, and other combinations purported to be universally beneficial. However, these generalized online dietary recommendations lack the individualized approach necessary for CKD patients. Unlike these social media-driven suggestions, established medical guidelines offer a more nuanced view of CKD dietary needs. This study investigates the discrepancies between these sources and their potential impact on patient health. Objective:The primary goal of this study is to identify and analyze the flaws in the dietary recommendation system for CKD patients that might adversely affect their health. By critically evaluating the content of YouTube videos, we aim to compare the dietary advice provided by social media influencers and content creators with established medical guidelines. Our approach combines qualitative and quantitative methods to thoroughly assess the accuracy and reliability of online dietary advice available to CKD patients. Method:We conducted four YouTube searches using keywords related to "diet plan" and "chronic kidney disease (CKD)." From each search, the first 30 videos were selected based on relevance, resulting in an initial pool of 120 videos. A stepwise screening process was used to filter out the most relevant and accessible content, ultimately narrowing the sample to 30 videos for in-depth analysis. The videos were evaluated using two scoring systems: the Journal of the American Medical Association (JAMA) score and the Global Quality Scale (GQS) score, which assess video quality. To ensure impartiality, three independent scorers conducted the evaluations. Additionally, two six-point scorecards were used to evaluate the inclusion and accuracy of information on various foods and eating behaviors affecting CKD risk, with higher scores indicating more comprehensive coverage. Data on video characteristics, such as view count, number of likes, and video age, were also collected to provide context and further insight into their reach and influence. Results:The study included 30 videos, with 60% (18 out of 30) posted by or featuring nephrology health professionals. Scorer 1 reported a mean JAMA score of 2.3 (SD 0.61) out of 4 points and a mean GQS score of 2.5 (SD 0.64) out of 5 points. Scorer 2 found a mean JAMA score of 2.5 (SD 0.62) and a mean GQS score of 2.8 (SD 0.73). Scorer 3 reported a mean JAMA score of 2.6 (SD 0.55) and a mean GQS score of 2.8 (SD 0.69). The dietary six-point scorecards revealed a mean score of 3.6 (SD 0.85) for the presence of information and 2.8 (SD 0.88) for the accuracy of the information. Conclusion:The videos analyzed in this study related to diet plans for CKD patients demonstrated generally low scores, indicating a lack of comprehensive and accurate information. Many videos provided incomplete or partial information, which could mislead viewers and potentially cause harm due to incomplete knowledge. This study highlights the need for careful scrutiny of online content, particularly on platforms like YouTube, due to the potential for contradictory information and its harmful consequences. The findings emphasize the necessity for greater accuracy and vigilance in disseminating health-related information to ensure the safety and well-being of CKD patients.

The Standard Model is not a complete description of reality; it omits the existence of dark matter, dark energy, and an explanation as to why no CP violation has been observed. However, some of these phenomena could be explained through a new force mediated by a new boson. If such a boson were massless it would result in a power law potential and if massive the interaction would be Yukawa-like. A previous experiment employing a micro-mechanical oscillator and a spherical test mass interactions was successful in placing the best limits on a mass-mass Yukawa-like interaction, but the data was never analyzed in the context of a power law. Here that data is analyzed considering a power law for powers n = 1-5 where n is the number of boson exchanges. The results show that the limits obtained through power law analysis of this data are not better than the currently accepted limits. A discussion of an experiment design capable of producing better limits on power law extensions to the Standard Model is presented, and suggests micro mechanical oscillators based experiment remains capable of improving the limits by at least one order of magnitude.

Spiking neural networks (SNNs) promise to perform tasks currently done by classical artificial neural networks (ANNs) faster, in smaller footprints and using less energy. Neuromorphic processors are set out to revolutionize computing at a large scale, but the move to edge-computing applications calls for finely-tuned custom implementations to keep pushing towards more efficient systems. To that end, we have examined the architectural design space for executing spiking neuron models on FPGA platforms, focusing on achieving ultra-low area and power consumption. This work presents an efficient clock-driven spiking neuron architecture used for the implementation of both fully-connected cores and 2D convolutional cores, which rely on deep pipelines for synaptic processing and distributed memory for weight and neuron states. With them, we have developed an accelerator for an SNN version of the LeNet-5 network trained on the MNIST dataset. At around 5.5 slices/neuron and only 348 mW, it is able to use 33% less area and 4 times as less power per neuron as current state-of-the-art implementations while keeping low simulation step times.

This paper sheds light on how crisis management affects post-disaster re-covery. Based on the study of the management of a major environmental disaster, hurricane IRMA, we consider how post-disaster recovery is impacted by crisis management strategies. The perspectives of local stakeholders from the islands of St Martin and St Barthélémy will be shared. We analyze how territories exposed to the same natural phenomena have different outcomes and consider some of the possible reasons. This study reveals underlying risk drivers, to address governance reorganization with a view to better managing socio-economic recovery.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

Drug resistance has become an extremely serious problem worldwide. Antibiotic resistance genes (ARGs) entering the environment with wastewaters promote replenishment of the resistome of natural microbioms. Distribution of several clinically significant ARGs in wastewaters of Rostov-on-Don (Southern Russia), lower reaches of the Don River and natural waters of the neighboring region was investigated. Metagenomic DNA samples isolated from 250 ml of wastewaters or natural waters and 200 mg of surface sediments were used for the study. Identification of the ARGs was carried out with end-point detection PCR. Presence of NDM, OXA-48, CTX-M, VanA, VanB, ErmB, and TetM/TetO genes was detected in urban wastewaters. Samples of wastewater treatment plant (WWTP) sewage were enriched with ARGs in contrast to non-treated wastewaters from the sewage collector. NDM, VanA, ErmB, TetM/TetO genes were found only in wastewaters and were absent in samples of natural waters and surface sediments. Only OXA-48, VanB and CTXM genes were found in natural waters and surface sediments. The described ARGs are quite typical for urban and hospital wastewaters. The target ARGs were detected in the samples connected to the anthropogenous sources of pollution such as Rostov municipal WWTP or livestock enterprise effluents.

We report magnetic silver nanoshells (M AgNSs) that have both magnetic and SERS properties for SERS-based detection. The M AgNSs are composed of hundreds of Fe3O4 nanoparticles for rapid accumulation and bumpy silver shell for sensitive SERS detection by near-infrared laser excitation. The intensity of the SERS signal from the M AgNSs was strong enough to provide single particle-level detection. We obtained much stronger SERS signal intensity from the aggregated M AgNSs than from the non-aggregated AgNSs. 4-Fluorothiophenol was detected at concentrations as low as 1 nM, which corresponds to 0.16 ppb. The limit of detection for tetramethylthiuram disulfide was 10 μM, which corresponds to 3 ppm. The M AgNSs can be used to detect trace amounts of organic molecules using a portable Raman system.

Background: Artificial intelligence can help improve the quality of healthcare by analyzing vast amounts of data and providing more effective and personalized treatment plans. Researchers are working on developing AI-powered solutions that can help improve the outcomes of patients. Objective: To explore the potential of AI in improving healthcare outcomes and patient experience. Results: The study suggests that AI can improve healthcare efficiency and patient outcomes but cannot fully replace human healthcare professionals. AI can assist healthcare professionals in their work, leading to better resource utilization and improved patient care. However, there is still a need for human healthcare professionals to oversee AI systems and provide empathy and personalized care to patients. Conclusion: While there is immense potential for AI in healthcare, it is not yet feasible to replace human healthcare workers. Instead, it should be viewed as a tool that can help improve the efficiency and effectiveness of human healthcare.

Time-series analysis is a widely used technique across various fields and industries, as it helps in understanding, predicting, and forecasting the behavior of data points over time. These fields include but are not limited to finance, economics, healthcare, transportation, etc. In the case of this paper, we have focused on finance. Predicting future values of financial time series offers several benefits. Accurate forecasts can help investors make better decisions about their investments. To predict future values, deep learning algorithms are commonly used since it is an effective method with complex data. In this study, we conduct a study that investigates the use of different data pre-processing techniques on deep learning algorithms in predicting the time series values. To conduct this experimental study, we utilize an open source software, which using long short-term memory technique as the representative deep learning technique, published in github software code repository platform. With this study, we investigate the effects of autoencoder and discrete wavelet transform data pre-processing techniques in time-series prediction. We discuss the details of the experimental study and report our results. The results show that time series prediction (using backtesting methodology) without any data pre-processing leads to 12.6% for mean absolute percentage error. The results also show that, time series prediction with the data preprocessing techniques (Wavelet Transform and Stacked Autoencoder) lead to 3.4%

The consequences of manipulations in structure and amino acid composition of native cyclolinopeptide A (CLA) from linen seeds and its linear precursor on their biological activities and mechanisms of action are reviewed. The modifications included truncation of the peptide chain, replacement of amino acid residues with proteinogenic or non-proteinogenic ones, modifications of peptide bond, and others. The studies revealed changes in the immunosuppressive potency of these analogs investigated in a number of in vitro and in vivo experimental models, predominantly in rodents, as well as differences in their postulated mechanism of action. The modified peptides were compared with cyclosporine A and parent CLA. Some of the synthesized and investigated peptides show potential therapeutic usefulness.

Optimizing input parameters not only improves production efficiency and processing quality but also plays a crucial role in the development of green manufacturing engineering practices. The aim of the present study is to conduct a comparative evaluation at cutting performance and machinability process during the turning of AISI 4340 steel under different cooling conditions. The study analyses cutting operations during turning using dry, minimum quantity lubrication (MQL), and nano-MQL. As control parameters in the experiments, three different cooling types, cutting speed (100, 150, 200 m/min), and feed rate (0.1, 0.15, 0.20 mm/rev) levels were applied. The experiment results present that the optimal output values are found as Vb=0.15 mm, Ra=0.81µm, 88.1 dB for sound intensity, and I=4.18 A for current. Moreover, variance analysis (ANOVA) was performed to determine the effects of input parameters on response values. Under dry, MQL, and nano-MQL processing conditions, parameters affecting tool wear, surface roughness, current by the motor shaft, and sound level were examined in detail, along with the chip morphology. The responses obtained were optimized according to the Taguchi S/N method. As a result of optimization, it was concluded that the optimum values for cutting conditions (A3B1C1) were nano-MQL cooling and V=100 m/min, f=0.1 mm/rev cutting. Last but not least, it was observed that there was a 13% improvement in tool wear, 7% in current, 9% in surface roughness, and 8% in sound intensity compared to the standard conditions. In conclusion, it was determined that nano-MQL and the lowest level of cutting and feed rate values provided the optimum results.

Post-translational modifications (PTMs) of histone residues shape the landscape of gene expression by modulating the dynamic process of RNAPII transcription. The contribution of particular histone modifications to the definition of distinct RNAPII transcription stages remains poorly characterized in plants. Chromatin Immuno-precipitation combined with next-generation sequencing (ChIP-seq) resolves the genomic distribution of histone modifications. Here, we review histone PTM ChIP-seq data in Arabidopsis thaliana and find support for a Genomic Positioning System (GPS) that guides RNAPII transcription. We review the roles of histone PTM “readers”, “writers” and “erasers”, with a focus on the regulation of gene expression and biological functions in plants. The distinct functions of RNAPII transcription during the plant transcription cycle may in part rely on the characteristic histone PTMs profiles that distinguish transcription stages.

Background: Antibiotic resistance is an overwhelming serious difficulty globally. This necessitates the exploration of novel sources of antibiotics to overcome this challenge. Aim of the study: Bacterial Myxopyronin A production from various soil environments Egypt; as well as testing its antimicrobial activity in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Different soil environments in Egypt were screened for the growth of bacterial isolates producing Myxopyronin A as an antimicrobial agent. Purification of Myxopyronin A was performed via reversed-phase HPLC. Paper disc diffusion assay, as well as broth dilution technique, were exploited to assess the invitro antimicrobial and minimum inhibitory concentration( MIC) of the test antibiotic. Furthermore, in vivo antimicrobial spectrum, adverse drug reactions, and pharmacokinetics were detected during animal model testing stages and human randomized clinical trials phases 1/2. Results: From the culture supernatant of the Myxobacterium Myxococcus fulvus 124B02 which was the predominant soil bacterial isolate grown on the Casein yeast peptone plate, Myxopyronin A was produced. The test antibiotic blocked the growth of many Gram +ve bacteria with MICs less than 100 mcg/ ml; whereas it inhibited the growth of a few Gram -ve bacteria such as Escherichia coli at MICs greater than 100 mcg/ ml. On the other hand, Eukaryotic cells such as fungal and human cells were not affected. Prokaryotic DNA-dependant-RNA polymerase( RNLP) was noticed to be inhibited via the test antibiotic suggesting its bactericidal action. Cmax was 7-8 mcg/ ml at Tmax 2 hours when 600 mg dose was orally administered in randomized human clinical trials phases 1/2; as well as T1/2 reached 2.5 hours following first-order kinetics of elimination. The duration of its action was nearly 12 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and cholestatic jaundice in less than 5 % of experimental candidates. Conclusion: The present study was promising due to the production of the bactericidal antibiotic Myxopyronin A from Myxococcus fulvus 124B02 isolated from different soil environments in Egypt.

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

Background: Antibiotic resistance is an overwhelming serious difficulty globally. This necessitates the exploration of novel sources of antibiotics to overcome this challenge. Aim of the study: Bacterial Myxopyronin A production from various soil environments Egypt; as well as testing its antimicrobial activity in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Different soil environments in Egypt were screened for the growth of bacterial isolates producing Myxopyronin A as an antimicrobial agent. Purification of Myxopyronin A was performed via reversed-phase HPLC. Paper disc diffusion assay, as well as the Broth dilution technique, were exploited to assess the invitro antimicrobial and minimum inhibitory concentration( MIC) of the test antibiotic. Furthermore, in vivo antimicrobial spectrum, adverse drug reactions, and pharmacokinetics were detected during animal model testing stages and human randomized clinical trials phases 1/2. Results: From the culture supernatant of the Myxobacterium Myxococcus fulvus 124B02 which was the predominant soil bacterial isolate grown on the Casein yeast peptone plate, Myxopyronin A was produced. The test antibiotic blocked the growth of many Gram +ve bacteria with MICs less than 100 mcg/ ml. In contrast, it inhibited the growth of a few Gram -ve bacteria such as Escherichia coli at MICs greater than 100 mcg/ ml. On the other hand, Eukaryotic cells such as fungal and human cells were not affected. Prokaryotic DNA-dependant-RNA polymerase( RNLP) was noticed to be inhibited via the test antibiotic suggesting its bactericidal action. The maximum concentration was 7-8 mcg/ ml at a maximum time of 2 hours when 600 mg dose was orally administered in randomized human clinical trials phases 1/2, and T1/2 reached 2.5 hours following first-order kinetics of elimination. The duration of its action was nearly 12 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and cholestatic jaundice in less than 5 % of experimental candidates. Conclusion: The present study was promising due to the bactericidal antibiotic Myxopyronin A production from Myxococcus fulvus 124B02 isolated from different soil environments in Egypt.

The objective of this study was to detail the monomer composition of resin-based dental materials sold in the market in 2023 and to evaluate the proportion of BPA derivatives in relation with their applications. A search on manufacturers’ websites was performed to reference resin-based dental materials currently on the market. Their monomer composition was determined from material safety data sheets and completed with a search on PubMed database. Among the 543 material compositions exploitable, 382 (70.3%) contained BPA derivatives. Among them, 56.2% contained BisGMA, 28% BisEMA, the most frequently reported. A total of 59 monomers of which 6 BPA-derivatives were found. 309 materials (56.9%) contained UDMA and 292 (53.8%) TEGDMA. Less than one third of materials identified contained no BPA derivatives. These proportions vary a lot depending on their applications with materials dedicated to dental care of young populations containing the highest proportions of BPA-derivatives monomers. The long-term effects on human health of the different monomers identified including BPA-derivatives monomers is a source of concern. For children and pregnant or lactating women arises the question to take a precautionary principle and avoid the use of resin-based dental materials likely to release BPA by opting for alternative materials.

Charles Darwin’s theory of evolution, his note as regards descent with modification, added greatly to the knowledge that we already possess of how species have survived down the ages. It is evident that this does not provide the necessary knowledge about the origin of the life on earth. However, it provides remarkable evidence about how life has survived. Looking fundamentally at the cellular construct of organisms, we arrive at the fact that cells, both unicellular and multicellular, have organelles that enable them communicate with one another. This ability for living organisms, down to the lowest - cellular life - to communicate is what I refer to as Biological interaction. It is necessary that we articulate more about this concept and see how this all comes to bear as regards Homeostasis. In reference to the latter, it is to be made known that every living organism is also intrinsically aimed towards a projected linear motion in its time riddled existence. This is to say that every living organism operates on an foundational process, amongst others, known as Homeostasis. We understand this term to mean balance that the living system strives to maintain. However etymologically speaking it means staying the same. How has this homeostatic process added to the fostering of life via biological interaction? How is biological interaction fundamental to the theory of evolution?

Introduction: Indonesia consists of a plural society with different ethnic, religious, racial, skin color, and other cultures. The difference must be understood by everyone, especially the younger generation in the digital age. If the younger generation does not have a sufficient understanding of multicultural education values, it will impact the moral crisis of the Indonesian nation. This research emphasizes the importance of multicultural education to the younger generation to understand the differences (pluralism) in society and respect them. Method: The method uses a qualitative method with the literature review method by collecting data on ten journals published in 2019, 2020, 2021. Results: The rise of socio-cultural conflicts in Indonesia is why applying multicultural values to the younger generation. Multiculturalism is needed to establish morals and sensitivity for a young person in the face of various social problems and symptoms at a growing age. Conclusion: Multicultural education is vital to the younger generation considering Indonesia has diverse nations and cultures. The efforts that can make to improve the morale of the nation's children, namely by learning citizenship education and religious education and utilizing information technology to spread things related to the values of multicultural education to the broader community

A challenging problem in the aquaculture industry is bacterial disease outbreaks which results in the global reduction of fish supply and foodborne outbreaks. Biofilms in marine pathogens protect against antimicrobial treatment and host immune defence. Zeolites are minerals of volcanic origin made from crystalline aluminosilicates which are useful in agriculture and in environmental management. In this study, silver ion-exchanged zeolite A of four concentrations; 0.25M (AgZ1), 0.50M (AgZ2), 1.00M (AgZ3)and 1.50M (AgZ4) were investigated for biofilm inhibition and antimicrobial properties against two predominant marine pathogens V. campbelli and V. parahemolyticus by employing the Minimum Inhibitory Concentration(MIC), Crystal Violet Biofilm Quantification assays as well as Scanning Electron Microscopy. In the first instance, all zeolite samples AgZ1-AgZ4 showed antimicrobial activity for both pathogens. For V. campbellii AgZ4 exhibited the highest MIC at 125.00 µg/ml while for V. parahaemolyticus the highest MIC was observed for AgZ3 at 62.50 µg/ml. At sublethal concentration, biofilm inhibition of V. campbelli and V. parahemolyticus by AgZ4 were observed at 60.2% and 77.3% inhibition respectively. Scanning electron microscopy exhibited profound structural alteration of the biofilm matrix by AgZ4. This is the first known study that highlights the potential application of ion-exchanged Zeolite A against marine pathogens and their biofilms.

Nitroxyl radical catalysts oxidize alcohols under an applied electric potential. It is possible to quantify the alcohol concentration from the resulting oxidation current. In this work, we evaluated the catalytic activity of nitroxyl radicals (or their corresponding hydroxylamines), including 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) as representative nitroxyl radicals, acetoamido-TEMPO, which shows higher oxidation potential than TEMPO owing to the acetoamido group, AZADO, Nor-AZADO, and NNO as less-hindered bicyclic nitroxyl radicals, and NHPI as an N,N-diacyl-type hydroxylamine, in acetonitrile solution. TEMPO, AZADO and NNO were also evaluated for their ability to oxidize alcohols in organic solvents, and their reactivity was compared with the electrochemical response. The most active NNO was used for electrochemical detection of cyclosporin A, a drug with a hydroxyl group.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

(1) Background: This manuscript introduces the "Lines and Dots" (LAD) technique, a novel method for administering Botulinum Toxin Type A (BoNT-A) in treating horizontal forehead lines. This technique emphasizes precision in targeting nerve endplates, considering individual anatomical variations, and optimizing treatment efficacy. (2) Methods: The LAD technique focus on using the frontalis muscle contraction dynamics to identify the specific distribution of the supraorbital and supratrochlear nerves It involves creating a grid of predetermined lines and points on the forehead that align with nerve paths and motor endplate zones. (3) Results: By targeting injections along these precise lines and points, the LAD technique ensures more effective utilization of BoNT-A. This approach not only enhances the toxin's effect but also allows for a reduction in the overall dosage. The strategic placement of injections results in a more natural, symmetrical, and sustained therapeutic effect, ensuring an improved aesthetic outcome. (4) Conclusions: The LAD technique represents a significant advancement in the realm of cosmetic injectables. It offers a tailored, patient-specific approach, maximizing the effectiveness of BoNT-A injections for treating forehead lines while minimizing risks and enhancing patient satisfaction. This method underscores the importance of a deep anatomical understanding and precision in cosmetic procedures.

This study examines the factors influencing consumer adoption of on-demand social media platforms characterized by ephemeral content. As these platforms rapidly gain popularity, understanding adoption drivers is crucial for researchers and practitioners. The study develops and tests a comprehensive model integrating traditional technology acceptance factors with platform-specific constructs. Using partial least squares structural equation modelling on data from 180 social media users in Kerala, India, the research reveals that convenience is the strongest predictor of adoption intention, followed by perceived usefulness, interpersonal influence, and enjoyment. Surprisingly, factors like perceived ease of use, social influence, and platform-specific features such as ephemerality and visual focus did not significantly impact adoption directly. Age showed a marginal negative effect, while gender had no significant impact. The findings challenge some prevailing assumptions about on-demand social media adoption and highlight the need for refined models specific to this context. The study contributes to technology adoption literature by demonstrating the primacy of convenience in driving the adoption of these platforms. It also offers practical insights for developers and marketers, suggesting that prioritizing convenience and perceived usefulness in design and marketing may be more effective than emphasizing specific features. Future research directions are proposed to address limitations and further explore this evolving digital landscape.

The article presents a methodology for modeling the impact of factors of both on-farm activity and environmental factors on the resulting indicators of an international company. The dataset includes the company's profit, revenue, valuation, share price, and market share from 2012 through 2022. This empirical period is optimal for such a type of modeling. Modeling the impact of carbon emissions factors on the resulting indicators is considered based on complex systems theory. Endogenous model variables include indicators of the development of the international company. Predefined model variables reflect the influence of both the external environment and internal factors on the development indicators of an international company. An approach of picture fuzzy rough sets based on time series of endogenous and exogenous variables can provide an opportunity to analyze and consider the consequences of feedback changes in the systems of which they are a part. Based on the results of the analysis of the model construction, it is concluded that picture fuzzy rough sets can be an excellent way to model interdependent social processes.

Isothermal Nucleic Acid Amplification based-Lateral Flow Testing (INAA-LFT) has emerged as a robust technique for on-site pathogen detection, providing a visible indication of pathogen nucleic acid amplification that rivals or even surpasses the sensitivity of real-time quantitative PCR. The isothermal nature of INAA-LFT ensures consistent conditions for nucleic acid amplification, establishing it as a crucial technology for rapid on-site pathogen detection. However, despite its considerable promise, the widespread application of isothermal INAA amplification-based lateral flow testing faces several challenges. This review provides an overview of the INAA-LFT procedure, highlighting its advancements in detecting plant viruses. Moreover, the review underscores the imperative to address existing limitations and emphasizes ongoing research efforts dedicated to enhancing the applicability and performance of this technology in the realm of rapid on-site testing.

Recent literature has seen a rapid expansion in the reference to front-end forensics as an indication of the untapped value of forensic science. While some of these contributions have centered on development of forensic intelligence from a single area of investigation, others call for a more fundamental change in the relationship between crime laboratories and policing, particularly relating early laboratory analysis with big datasets to provide leads to investigators. We highlight several recently implemented tactical strategies of crime laboratories that contribute to the body of forensic intelligence. Beyond the scientific gains from these tactical applications, the corresponding details on associated efficiencies, costs, time savings, and quality improvements offer insights towards patterns of success for the community of crime laboratories. Further details expand an interpretation of what constitutes success with an eye on the contributions of the crime laboratory towards public health, safety, and protection of the innocent in addition to societal gains from conviction of the guilty. The economic interpretation of the value provided by the forensic laboratory assists in the cost-benefit review of strategic and tactical decisions and supports the justification for laboratory public funding with measures of the return on investment from public support of the forensic laboratory

The short-lived positron-emitter carbon-11 (t1/2 = 20.4 min; b+, 99.8%) is prominent for labeling tracers for use in biomedical research with positron emission tomography (PET). Carbon-11 is produced for this purpose with a cyclotron, nowadays almost exclusively by the 14N(p,a)11C nuclear reaction, either on nitrogen containing a low concentration of oxygen (0.1–0.5%) or hydrogen (~ 5%) to produce [11C]carbon dioxide or [11C]methane, respectively. These primary radioactive products can be produced in high yields and with high molar activities. However, only [11C]carbon dioxide has some utility for directly labeling PET tracers. Primary products are required to be converted rapidly and efficiently into secondary labeling synthons to provide versatile radiochemistry for labeling diverse tracer chemotypes at molecular positions of choice. This review surveys known gas phase transformations of carbon-11 and summarizes the important roles that many of these transformations now play for producing a broad range of labeling synthons in carbon-11 chemistry.

The mechanical effects of membrane compositional inhomogeneities are analyzed in a process analogous of neck formation in cellular membranes. We cast on the Canham-Helfrich model of fluid membranes with both the spontaneous curvature and the surface tension being non-homogeneous functions along the cell membrane. The inhomogeneous distribution is determined by the equilibrium mechanical equations and the boundary conditions as considered in the axisymmetric setting compatible with the necking process. To establish the role played by mechanical inhomogeneity, we focus on the catenoid, a surface of zero mean curvature. Analytic solutions are shown to exist for the spontaneous curvature and the constrictive forces in terms of the border-radii. Our theoretical analysis shows that the inhomogeneous distribution of spontaneous curvature in a mosaic-like neck constrictional forces potentially contributing to the membrane scission under minimized work in living cells.

The way Norway is spearheading electrification in the transport sector is of global interest, and details of its policies and emission impacts represent a reference. We used the NERVE model, a bottom-up high-resolution traffic emission model, to calculate all exhaust emissions in Norway (2009-2020). This allows us to evaluate the co-benefit of policies to target climate change mitigation and air quality. We have analyzed local municipal data with regards to traffic growth, road network influences, vehicle composition, emissions and energy consumption. Light vehicle CO2 emissions per kilometre have been reduced by 22% since 2009, mainly driven by an increaseing bio-fuel mixing and BEV share. BEVs are mostly located in and around the main cities, areas with young vehicle fleets, and strong local incentives. Beneficiaries of all BEVs incentives have been a subset of the population with strong economic indicators. The incentivized growth in the share of diesel-fuelled passenger vehicle has been turned, and together with Euro6 emission standards, light vehicle NOx emissions have been halved since peaking in 2014. BEV represent an investment in emission reductions in years to come and current sales set up for an accelerated decline in emissions despite growth in traffic.

Introduction: In general, everyone believes that the smallest preterm infants should achieve normal intrauterine growth rates, but many thinks that this is not possible with current nutrition guidelines. There is resistance to giving enough nutrition for fear of "toxicity". The difference in weight Z-score between birth and a corrected gestational age (CGA) at discharge is assess in postnatal growth in our unit. Material and methods: An observational study was done between January 2018 and December 2020 where all cases that had ≤ 29 weeks of GA at birth and survived to 36 weeks corrected GA or that were discharged home. An aggressive nutrition protocol including parenteral as well as enteral nutrition was followed. Patients and their weight trajectory was plotted on the Fenton 2013 growth curve. The patients who had had a smaller WZP difference were also plotted. Results: A total of 32 cases were found. The median change in Z-score between birth and discharge of the whole group was -0.52 (IQR 0.53). Six of 32 (19%) had a more than one WZP, all of whom had severe pathologies. The median decline in Z score for this group with poor growth was 1.24 (IQR 0.22). There were 26 cases with a < 1 WZP (81%) and a median Z score fall of 0.39 (IQR 0.55). No important complications secondary to the ingested volumes or parenteral nutrition were reported. Conclusion: The group of cases with a > 1 WZP drop had severe pathologies. All the other cases had adequate growth parallel to normal weight growth charts and a few cases had some catch-up growth. The study showed that it is possible for many preterm infants to achieve normal intrauterine growth rates if they are given enough nutrition, but bigger multicenter studies are needed to confirm these findings.

Saiga (Saiga tatarica) was extirpated in China. Since Mid-1980s, attempts have been made for revival the species in the country, however, only a breeding herd of Saiga was successfully established at Wuwei, Gansu, China. The reintroduced Saiga population experienced a bumpy growth. Then, the population collapsed following the catastrophe die-off in the Saiga ranging countries in Central Asia, then population started to rebound when 6 new lams were born in 2019. After reviewing the population trend and conservation breeding of Saiga in China, we concluded that to establish a migratory species that needs vast range size like Saiga on central Asia steppe, an international collaboration is needed for introducing new genes. We recommend China to ratify the CMS in order to facilitate international conservation efforts to restoring the species in its former range.

Manufacturing of grinding wheels is continuously adapting to new industrial requirements. New abrasives and new wheel configurations, together with wheel wear control allow for grinding process optimization. However, the wear behavior of the new abrasive materials is not usually studied from a scientific point of view due to the difficulty to control and monitor all the variables affecting the tribochemical wear mechanisms. In this work an original design of pin on disk tribometer is developed in a CNC grinding machine. An Alumina grinding wheel with special characteristics is employed and two types of abrasive are compared: White Fused Alumina (WFA) and Sol-Gel Alumina (SG). The implemented tribometer reaches sliding speeds of between 20 and 30 m/s and real contact pressures up to 190 MPa. The results show that the wear behavior of the abrasive grains is strongly influenced by their crystallographic structure and the tribometer appears to be a very good tool for characterizing the wear mechanisms of grinding wheels, depending on the abrasive grains.

This article presents and discusses analytical data on the scientific publication record from 1910 to 2020 on two topics: "climate" and "climate change/global warming/climate emergency". The goal is to visualize how the publication record on these two topics has evolved over time, from different classification perspectives (year, country, source and organization). Three hypotheses are tested using data collected from Web of Science and various graphical representations of the data. It is found that research output related to the Earth’s contemporary changing climate overtook that of general climate research in 2011, and the publication ratio has been expanding in the last decade. There are significant differences in the publication countries and sources between the two topics, and conversely less significant differences in terms of organizations publishing these works. Differentiation factors that affect the level of research output and engagement on the climate challenge include: island versus landlocked nations, specialized versus general scientific journals, academic versus institutional organizations. The future of the publication records is discussed, such as the emergence of new terms to refer to the climate challenge, such as “climate emergency”.

This study focused on the characterization of lactic acid bacteria (LAB) in a renowned traditional Italian cheese, Pecorino di Farindola, to select an autochthonous culture and investigate its po-tential for the improvement of safety and functional properties. Two hundred and six LAB isolated throughout production and maturation from nine cheese lots of three farms were identified by 16S rRNA gene sequencing and tested for the presence of genes encoding virulence factors, vancomycin resistance (for enterococci), biogenic amines (BAs) and bacteriocin production, for antimicrobial activity, and for the capacity to survive in the gastro-intestinal tract (GIT) based on tolerance to low pH and bile salts and adhesion to CaCo-2 cells. A Lacticaseibacillus paracasei isolate was used in cheese making and determined a decline of spiked Listeria monocytogenes and Escherichia coli O157 faster than in control cheese. The autochthonous bacterial groups were numerically unaffected, apart from lactobacilli that were recovered in higher numbers in the cheese with added L. paracasei. Based on Repetitive Extragenic Palyndrome (Rep) PCR profiles, the added strain possibly dominated until day 88 in cheese. Results encourage further trials with autochthonous cultures to efficiently inhibit hazardous bacteria and enrich a functional microbiota in Pecorino di Farindola and similar cheeses.

The açaí (Euterpe oleracea Mart.) is a native fruit of the Amazon that is well-known due to its commercial value. Its production chain is centered in the state of Pará, largely supplied by extractivism. The processing of açaí fruits in nature generates huge amount of solid waste, which can pose serious risks to the environment if not used and managed properly. Due to a small number of systhematic studies on the effect of chemical activation by pyrolysis of açaí seeds and fibers, and with the aim of providing a basis for future applications of the waste generated by processing of açaí fruits, the present work proposes a study of the pyrolysis of açaí seeds and fibers and the physicochemical and compositional characterization of the aqueous phase products. In this way, açaí seeds were collected from a local artisan processing facility in the city of Belém, PA. The seeds were dried at 105°C until constant weight, and subsequently, the fibers were separated from the seeds in a rotating drum. The seeds and fibers were impregnated with NaOH solutions at 0.5M, 1.0M, and 2.0M, and then pyrolyzed at a laboratory scale at 450 °C and 1 atm. The liquid products from pyrolysis were characterized through acidity index analysis, Fourier-transform infrared spectroscopy, and gas chromatography. The increase in the concentration of the impregnating agent resulted in an increase in bio-oil yield from both the seeds and fibers, rising from 3.3% (raw seeds) to 6.6% (seeds impregnated with 2M NaOH) and from 1.2% (raw fibers) to 3.7% (fibers impregnated with 2M NaOH). The yield in the aqueous phase after biomass pyrolysis showed an inverse behavior to the bio-oil yield, decreasing from 33.7% (raw fibers) to 21.2% (fibers impregnated with 2M NaOH) and from 41% (raw seeds) to 37.5% (seeds impregnated with 2.0M NaOH). High acidity levels were found in the aqueous phase samples and bio-oils derived from the seeds and fibers, which decreased as the concentration of the impregnating agent increased. The increase in the concentration of the impregnating agent (NaOH) influenced the chemical composition of the obtained liquid products, leading to a decrease in oxygenated compounds and an increase in nitrogenous compounds in both experimental matrices, which was also evidenced by the reduction in acidity.

Gastric cancer is a challenging public health concern worldwide and remains a leading cause of cancer-related mortality. The primary risk factor implicated in gastric cancer development is infection with Helicobacter pylori. H. pylori induces chronic inflammation affecting the gastric epithelium, which can lead to DNA damage and promotion of precancerous lesions. Disease manifestations associated with H. pylori are attributed to virulence factors with multiple activities and its capacity to subvert host immunity. One of the most significant H. pylori virulence determinants is the cagPAI gene cluster, which encodes a type IV secretion system and the CagA toxin. This secretion system allows H. pylori to inject the CagA oncoprotein into host cells, causing multiple cellular perturbations. Despite the high prevalence of H. pylori infection, only a small percentage of affected individuals develop significant clinical outcomes, while most remain asymptomatic. Therefore, understanding how H. pylori triggers carcinogenesis and its immune evasion mechanisms is critical in preventing gastric cancer and miti-gating the burden of this life-threatening disease. This review aims to provide an overview of our current under-standing of H. pylori infection, its association with gastric cancer and other gastric diseases, and how it subverts the host immune system to establish persistent infection.

The nutrient absorption and utilization efficiency in the roots of seedlings are beneficial for increasing crop yield. Creating marker assisted selection for wheat root traits can assist wheat breeders in choosing robust roots to maximize nutrient uptake. Exploring and identifying the effect of different nitrogen applications on RSA is of great significance for breeding nitrogen efficient wheat varieties. In this study, A total of 243 wheat varieties native to the Yellow and Huai Valley regions of China were utilized for genome-wide association studies (GWAS). Furthermore, a recombinant inbred line (RIL) population of 123 lines derived from the cross between Avocet and Chilero was utilized for linkage examination and confirmation of the hereditary loci distinguished by GWAS. Five RSA traits include the relative number of root tips (RNRT); relative total root length (RTRL); relative total root surface area (RTRS); relative total root volume (RTRV) and relative average root diameter (RARD) where evaluated under two N conditions—normal N (NN) supply and low N (LN)—to characterize the NUE of each accession. GWAS and linkage analysis were performed by integrating data from the wheat 660k single nucleotide polymorphism (SNP) chip and diversity arrays technology (DArT) to identify genetic loci associated with RSA. The results showed that based on the ratio of RSA related traits under two N supply conditions, a total of 598 SNP markers, which are significantly associated with RSA related traits, were detected at 160 genetic loci by GWAS. A total of 10 QTL loci related to RSA were dis-covered and identified by linkage mapping. In which, three significant RSA related Quantitative Trait Locus (QTL) were identified, namely qRtrl-3D, qRnrt-3D, and qRtrl-7D. The study has the potential to enhance the effectiveness of selecting root traits in wheat breeding programs, offering valuable insights into the genetic underpinnings of nitro-gen use efficiency (NUE) in wheat. This could lead to the creation of NUE wheat varieties by implementing focused breeding strategies.

Neuromorphic computing, a brain inspired non-Von Neumann computing system, addresses the challenges posed by the Moore’s law memory wall phenomenon. It has the capability to increasingly enhance performance while maintaining power efficiency. Neuromorphic chip architecture requirements vary depending on the application and optimizing it for large-scale applications remains to be a challenge. Neuromorphic chips are programmed using spiking neural networks which provide them with important properties such as parallelism, asynchronism, and on-device learning. Widely used spiking neuron models include the Hodgkin-Huxley Model, Izhikevich model, integrate-and-fire model and spike response model. Hardware implementation platforms of the chip follow three approaches: analog, digital, or a combination of both. Each platform can be implemented using various memory topologies which interconnects with the learning mechanism. Current neuromorphic computing systems typically use the unsupervised learning spike timing-dependent plasticity algorithms. However, algorithms such as voltage-dependent synaptic plasticity have the potential to enhance performance. This review summarizes the potential neuromorphic chip architecture specifications and highlights which applications they are suitable for.

KThe promising possibility of organic photodetector (OPD) is emerging in the field of sensing applications for its tunable absorption range, flexibility, and large-scale fabrication abilities. In this work, we fabricated bulk heterojunction OPD with a device structure of glass/ITO/PEDOT:PSS/ P3HT:PC61BM/Al by spin coating process and characterized the dark and photocurrent at different applied bias conditions for red, green, and blue incident LED light. OPD photocurrent density exhibited up to 2.5–3 orders higher magnitude compared to the dark current density at -1 V bias while it increased up to 3–4 orders at zero bias conditions for red, green, and blue lights showing an increasing trend higher voltage applied in the negative direction. Different OPD inner periphery shapes, OPD to LED distance, and OPD area were also considered to bring the variation in OPD dark and photocurrent, which can affect the on/off ratio of the OPD–LED hybrid system and is a critical phenomenon for any sensing application.

Large language models (LLMs) have shown impressive performance and versatility. However, their billions of parameters and high computational costs hinder the development of personalized and privacy-preserving AI assistants operating locally on user devices. In this work, we explored the potential of pruning LLMs to create lightweight models suitable for user devices, using the moderate-sized Llama-2 7B model as an example. By adopting a simple yet effective pruning method, we found that up to 60% of the weights in the Llama-2 7B model could be pruned without significantly impairing its language modeling capabilities. Furthermore, despite occasional factual inaccuracies, the pruned model at the sparsity limit generated fluent and helpful answers to daily queries, demonstrating its feasibility of on-device AI assistants. These inaccuracies might originate from forgetting or hallucination due to pruning. We proposed a simple protocol to distinguish between the two mechanisms, as well as future directions to improve the pruned models for local AI assistants.

A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

With the increase in technological advancements, architects and engineers over the past couple of decades have been trying to achieve high efficiency within construction projects. Their goals also include reducing global warming effects from construction and building new construction faster for the growing population in urban cities. This requires using a construction method that is less harmful to the environment and faster than other traditional methods. Modular construction, also known as modular construction, is the method that has the potential to make this happen. This review paper discusses what modular construction is and how it is different from the traditional on-site construction. Environmental impacts of using modular construction and what leads to it being more efficient and faster than on-site construction. The study doesn’t suggest that modular construction is the solution to all the problems being faced in the construction industry today, but it is a potential solution that if used in the right situation and correct manner, can have a huge positive impact on the construction industry.

(1) Background: Since the pandemic, adolescent girls have increasingly faced mental health challenges. We examined prevalence trends and associated risk factors for depression among adolescent girls. 2) Methods: Data for girls aged 12 to 17 years (N=4346) from the 2021 cross-sectional National Survey on Drug Use and Health were analyzed. Factors associated with depression were examined using multiple regression analysis. (3) Results: Rates of severe depression were significantly higher (p&lt;.001) in older girls (adjusted odds ratio [AOR]: 1.63, 1.61, those who did not have authoritative parents (AOR: 3.40), and those with negative school experiences (AOR: 4.03). Black and Asian/Native Hawaiian or other Pacific Islanders were less likely to report severe depression than white girls. As previously reported, non-White girls were significantly less likely to receive treatment for depression (p&lt;.05). Parents’ characteristics and school experiences had no effect on the likelihood of receiving mental health treatment. (4) Conclusion: Depression has become increasingly common among American adolescent girls, who are now three times as likely as adolescent boys to have had recent experiences with depression. Our results show that family structure, parenting style, and negative school experiences significantly contribute to the rate of depression and that treatment disparities exist with regard to race and ethnicity.

This proposed research explores a novel approach to image classification by deploying a complex-valued neural network (CVNN) on a field-programmable gate array (FPGA), specifically for classifying 2D images transformed into polar form. The aim of this research is to address the limitations of existing neural network models in terms of energy and resource efficiency, by exploring the potential of FPGA-based hardware acceleration in conjunction with advanced neural network architectures like CVNNs. The methodological innovation of this research lies in the Cartesian to polar transformation of 2D images, effectively reducing the input data volume required for neural network processing. Subsequent efforts focused on constructing a CVNN model optimized for FPGA implementation, emphasizing the enhancement of computational efficiency and overall performance. The experimental findings provide empirical evidence supporting the efficacy of the image classification system developed in this study. One of the developed models, CVNN_128, achieves an accuracy of 88.3% with an inference time of just 1.6ms and a power consumption of 4.66mW for the classification of the MNIST test dataset consists of 10,000 frames. While there is a slight concession in accuracy compared to recent FPGA implementations that achieve 94.43%, our model significantly excels in classification speed and power efficiency—surpassing existing models by more than a factor of 100. In conclusion, the paper demonstrates the substantial advantages of FPGA-implementation of CVNNs for image classification tasks, particularly in scenarios where speed, resource, and power consumption are critical. The study’s reproducible results and corresponding code are available on GitHub at the following link: https://github.com/mahmad2005/CVNNonFPGA

Influence of reaction time on silver nanoparticles-catalyzed oxidation of 3,3’,5,5’-tetramethylbenzidine (TMB) was evaluated via probing the oxidation process by recording the UV-Visible absorbance of the resulting colored products of TMB oxidation by hydrogen peroxide in the presence of silver nanoparticles as peroxides mimics. The time curve of the oxidation process was constructed, revealed that the concentration of the oxidation product was increased by increasing the reaction time and then levled off because the nanozyme active nodes were saturated after a certain reaction time and consequently the steady-state condition can be observed. The maximal activity of the silver nanozymes was achieved after a very short reaction time as short as 3.0 min and after this time, the color intensity of the oxidation products remained constant, revealing saturation of active nodes of nanoparticles with nanozyme-substrate.

Keywords: Kenaf; liquid cultivation; solid cultivation; in vitro propagation, life on land