An ethanol vapor sensor based on a microfiber with quantum-dots (QDs) gel coating is proposed and demonstrated. The QDs gel was made from UV glue as the gel matrix and the CdSe/ZnS QDs with a concentration of 1mg/mL. The drawing and coating process were conducted by using a simple and low-cost home-made system. The bending, ethanol sensing, temperature response and time response tests were carried out, alternatively. The experimental results show that the fabricated sensor has a high sensitivity of -3.3%/ppm, a really low temperature cross-sensitivity of 0.17 ppm/℃ and a fast response time of 1.1s. The robust structure with ease of fabrication and excellent sensing performance render it a promising platform for real ethanol sensing application.

Acoustic emission (AE) has proven to be a very useful technique for determining damage in ceramic matrix composites (CMCs). CMCs rely on various cracking mechanisms which enable non-linear stress-strain behavior with ultimate failure of the composite due to fiber failure. Since these damage mechanisms are all micro-fracture mechanisms, they emit stress waves ideal for AE monitoring. These are typically plate waves since for most specimens or applications one dimension is significantly smaller than the wavelength of the sound waves emitted. By utilizing the information of the sound waveforms captured on multiple channels from individual events, the location and identity of the sources can often be elucidated. The keys to the technique are the use of wide-band frequency sensors, digitization of the waveforms (modal AE), strategic placement of sensors to sort the data and acquire important contents of the waveforms pertinent for identification, and familiarity with the material as to the damage mechanisms occurring at prescribed points of the stress history. The AE information informs the damage progression in a unique way which adds to the understanding of the process of failure for these composites. The AE methodology was applied to composites tested in fatigue at different frequencies where identification of when and where AE occurred coupled with waveform analysis leads to source identification and failure progression.

In this paper, a geometric body-centered model to simulate the periodic structure of unidirectional fibrous composites is presented. To this end, three prescribed configurations are introduced to predict in a deterministic manner the arrangement of internal and neighboring fibers inside the matrix. Thus, three different representative volume elements (RVEs) are established. Furthermore, the concept of the interphase has been taken into account, stating that each individual fiber is encircled by a thin layer of variable thermomechanical properties. Next, these three unit cells are transformed in a unified manner to a coaxial multilayer cylinder model. This advanced model includes the influence of fiber contiguity in parallel with the interphase concept on the thermomechanical properties of the overall material. Then, by the use of this model, the authors propose explicit expressions to evaluate the longitudinal and transverse thermal conductivity of this type of composite. The theoretical predictions were compared with experimental results, as well as with theoretical values yielded by some reliable formulae derived from other workers, and a reasonable agreement was found.

Increasing numbers of researchers are interested in the importance of dietary fiber for the gut microbiota, microbiotal metabolite SCFA, energy metabolism and gut health of the host. However, studies have demonstrated that long-term and longitudinal observation may be needed to evaluate the effect of dietary fiber better, and few such works have been made in chickens. Therefore, we successively fed low-fiber, high--fiber and low-fiber diets to two breeds of chickens during different growth periods (1—8, 9—20 and 21—50 weeks), aiming to longitudinally observe the long-term effect of altered dietary fiber on the gut microbiota, SCFA and development of cecum of chickens with age. The results showed that the composition and function of the gut microbiota, SCFA and the development of the cecum were different during different periods, which was largly affected by dietary fiber. However, the causes of some effects were different during the different periods. For example, compared with that in low-fiber chickens at 8 weeks, dominant fiber-degradation bacteria such as Bacteroidetes, Alloprevotella and SCFA-producing bacteria such as Faecalibacterium increased due to a high-fiber diet at 20 weeks, while due to a high feed intake in 50 weeks. Moreover, the concentration of SCFA in 20 weeks was significantly higher than in 8 weeks and 50 weeks, but the causes of this difference were also distinct. It was proposed that a long-term observation was needed to evaluate the effect of dietary fiber better on chickens. The metabolite pathways of ATP-binding cassette (ABC) transporters encoded by Firmicutes were enriched in 8 weeks, while a two-component system and β–glucosidase encoded by Bacteroidetes were enriched in 20 and 50 weeks. The trend was the same in two breeds of chickens except for Alloprevotella. In addition, the total content of SCFA in the contents of cecum was also affected by the size of the cecum. Surprisingly, the length of the cecum shortened from 20—50 weeks, maybe due to reduced dietary fiber.

The potentiality of cv. Malbec grape pomace (GP) as a functional ingredient in the formulation of bakery foods (muffins, biscuits and cereal bars) was studied. The effect of GP addition on the phenolic compounds (PCs) composition, nutritional and sensory properties were evaluated. The addition of GP increased the content of dietary fiber, proteins, ash, total phenolic content (TPC), antioxidant activity (AA), anthocyanins and non-anthocyanins PCs while decreasing the carbohydrates content. The main PCs given by the GP to supplemented foods were (-)-gallocatechin, quercetin-3-O-glucoside, rutin, caffeic acid, syringic acid and (+)-catechin. For anthocyanins, the acylated derivatives were more stable to heat treatment (baking) in food processing which was evidenced by a higher proportion of these PCs compounds when compared to the same derivatives quantified in GP. In general, when the TPC or individual concentrations of PCs were analyzed in a nutritional or functional context, one portion of the supplemented foods showed levels high enough to satisfy the recommended dose per day of these bioactive compounds. Additionally, the foods were well received by consumers during the sensory evaluation and supplemented biscuits got the highest acceptability. This study demonstrated that GP could be a viable functional ingredient in bakery foods to give nutritionally enhanced properties like TPC, PCs, AA and dietary fiber in consumer’s diets.

Dietary fibers regulate intestinal barrier function; however, the precise mechanisms remain unclear. This study investigated the effects of psyllium fibers on antimicrobial protein expression, focusing on the type II immunity and tuft cell-group 2 innate lymphoid cell (ILC2) circuit in the small intestine of the mouse. Supplemental psyllium fiber upregulated antimicrobial proteins, such as small proline-rich protein 2A (SPRR2A) and resistin-like beta (RELMβ), in mouse small intestine, evidently affecting cecal microbiota composition. Psyllium fibers also increased the RNA and protein expression of molecules related to ILC2 and tuft cells, such as IL-13, IL-25, DCLK1, Gfi-1b, SH2 domain-containing protein 3C, and Spi-B. In addition, ILC2 inhibitor (disulfiram) and bitter taste receptor blocker administration reduced psyllium-induced SPRR2A and RELMβ expression. Collectively, psyllium supplementation upregulates antimicrobial proteins such as SPRR2A and RELMß via the type II immune response and tuft cell-ILC2 circuit in the mouse small intestine.

In the paper we show that the general relativity in recent Einstein-Palatini formulation is equivalent to a gauge field. We begin with a bit of information of the Einstein-Palatini formulation and derive Einstein field equations from it. In the next section, we consider general relativity with a positive cosmological constant in terms of the corrected curvature. We show that in terms of the corrected curvature general relativity takes the form typical for a gauge field. Finally, we give a geometrical interpretation of the corrected curvature.

Sporadic inclusion body myositis (sIBM) is the most common muscle disease of older people and is clinically characterized by slowly progressive asymmetrical muscle weakness, predominantly affecting quadriceps, deep finger flexors and foot extensors. At present there are no enduring treatments for this relentless disease that eventually leads to severe disability and wheelchair dependency. Although sIBM is considered a rare muscle disorder, its prevalence is certainly higher as the disease is often undiagnosed or misdiagnosed. The histopathogical phenotype of sIBM muscle biopsy includes muscle fiber degeneration and endomysial lymphocytic infiltrates that mainly consist of cytotoxic CD8+ T cells surrounding nonnecrotic muscle fibers expressing MHCI. Muscle fiber degeneration is characterized by vacuolization and accumulation of congophilic misfolded multi-protein aggregates, mainly in their non-vacuolated cytoplasm. Many players have been identified in sIBM pathogenesis including environmental factors, autoimmunity, abnormalities of protein transcription and processing, accumulation of several toxic proteins, impairment of autophagy and ubiquitin proteasome system, oxidative and nitrative stress, endoplasmic reticulum stress, myonuclear degeneration, and mitochondrial dysfunction. Aging has been also proposed as a contributor to the disease. However, the interplay between these processes and the primary event that leads to the coexistence of autoimmune and degenerative changes is still under debate. Here, we outline our current understanding of disease pathogenesis, focusing on degenerative mechanisms, and discuss the possible involvement of aging.

The performance of a normal-strength SHCC under impact loading was studied using the results obtained from a split Hopkinson tension bar (SHTB). The focus of the investigation is to explain the mechanisms behind the peculiar rate-dependent behavior of SHCC under tensile loading. With the help of frames obtained by high-speed cameras and the subsequent Digital Image Correlation (DIC) analysis, the stress-strain relation of the SHCC obtained in SHTB was analyzed. The investigation of the composite’s behavior was supported by constituent-level experiments on the non-reinforced matrix of the SHCC and on the fiber-matrix bond. In the case of the constituent matrix, the well-known apparent increase in the tensile strength of the cement-based matrix and its influence on the behavior of SHCC was studied. For this purpose, experiments on the SHCC specimens with different geometries were performed in the SHTB. The results obtained from these experiments and those obtained by DIC show that commonly used analytical models, in which the specimen is assumed elastic, cannot capture the effects of structural inertia on the results. Thus, an alternative novel method based on the results of DIC has been used to explain and quantify the contribution of structural inertia. The rate-dependent behavior of the fiber-matrix bond was studied by performing high-speed single fiber pullout tests in a miniaturized split Hopkinson tension bar. This novel experimental technique enabled explanation of the rate-dependent bridging action of the fibers in SHCC. Based on the results, the enhanced behavior of SHCC under impact loading is explained.

Due to the renewed variation in government and political systems inside and outside countries, and with the high tariffs at borders, the latter have become an outlet for terrorism and smugglers. Therefore, each country seeks to develop its own protection system, and the technologies used in these systems vary according to the severity and the importance of the installations to be protected, it is found that some of them are expensive and unnecessary, but other have good and variable levels of efficiency. Consequently, the idea of designing a surveillance system that can monitor and control access becomes indispensable. In the same context, this work is of crucial strategic and geopolitical importance. It combines pre-existing alarm and monitoring methods and revolutionary Internet of Things (IoT) application products, of which Wireless Sensor Networks (WSN) and Optical Fiber Sensors (OFS) are part of this application. This article presents the distribution of wireless radar nodes accompanying with a Bragg fiber sensor to identify each rolling intruder incoming the zone to be monitored, from the determination of its speed, weight and wheelbase distance.

This work presents results of property researches of fabricated samples of silica few-mode optical fiber (FMF) with induced chirality under twisting 10 and 66 revolutions per meter, core diameter 11 µm, typical “telecommunication” cladding diameter 125 µm and improved height of quasi-step refractive index profile. Proposed FMF supports 4 guided modes over “C”-band. We represent results of computed characteristics, as well as experimentally measured spectral responses of laser-excited optical signals, including researches and analysis of few-mode effects, occurring after fiber Bragg grating writing.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

The thermomechanical and viscoelastic properties of a glass fiber polyethylene terephthalate glycol (GF/PETG) continuous unidirectional (UD) tape were investigated using differential scanning calorimetry (DSC), thermo-mechanical analysis (TMA), and dynamic mechanical analysis (DMA). The study identified five operational conditions based on Army Regulation 70-38 Standard. The DSC results revealed a glass transition temperature of 78.0 ± 0.3°C, guiding the selection of temperatures for TMA and DMA tests. TMA provided the coefficient of thermal expansion in three principal directions, consistent with known values for PETG and GF materials. DMA tests, including strain sweep, temperature ramp, frequency sweep, creep, and stress relaxation, defined the linear viscoelastic region and temperature-dependent properties of the material. The frequency sweep indicated an increase in modulus with rising frequency, identifying several natural frequency modes. Creep and stress relaxation tests showed time-dependent behavior, with strain increasing under higher loads and stress decreasing over time for all tested input values. Viscoelastic models fitted to the data yielded R² values of 0.99, demonstrating good agreement. The study successfully measured thermo-mechanical and viscoelastic properties across various conditions, providing insights into how temperature influences the material's mechanical response under extreme conditions.

In this work, numerical and experimental implementation of a state observer applied to an Erbium-Doped Fiber Laser (EDFL) has been developed. The state observer is designed through the mathematical model of the EDFL to estimate the non-measurable variable; however, in numerical estimation, the state variables can be measurable given the mathematical model. Only the laser intensity variable was experimentally measured. The state observer estimated the population inversion through the obtained experimental laser intensity time series fitted with their numerical laser intensity using the mean square error (MSE) tool. A bifurcation diagram of the population inversion time series local maximum was built from the state observer. The state space of the experimental laser intensity versus observed population inversion was built.

Outlined is a proposal designed to culminate in the foundry fabrication of arrays of singly addressable quantum dot sources deterministically emitting single pairs of energy-time entangled photons at C-band wavelengths; each pair having negligible spin-orbit fine structure splitting; each pair being channeled into single mode pig-tail optical fibers. Entangled photons carry quantum state information among distributed quantum servers via I/O ports having two functions; the unconditionally secure distribution of decryption keys to decrypt publicly distributed, encrypted classical bit streams as input to generate corresponding qubit excitations, and to convert a stream of quantum nondemolition measurements of qubit states into a classical bit stream. Outlined are key steps necessary to fabricate arrays of on-demand quantum dot sources of entangled photon pairs, principal among are 1) foundry fabrication of arrays of isolated quantum dots, 2) generation of localized sub-surface shear strain in a semiconductor stack, 3) a cryogenic anvil cell, 4) channeling entangled photons into single mode optical fibers, 5) unconditionally secure decryption key distribution over the fiber network, 6) resonant excitation of a Josephson tunnel junction qubits from classical bits, and 7) conversion of a quantum nondemolition measurements of a qubit states into a classical bit.

This study introduces a Fiber Specklegram Sensor (FSS) design for temperature measurement utilizing a single-multi-single mode optical fiber configuration. FSS technology offers unique advantages for potential development into portable sensing systems. This investigation explores an FSS design compatible with miniaturization by optimizing the interrogation system based on the relationship between speckle grain size and filtering fiber area. Temperature variations are detected through fluctuations in optical power at the sensor output, offering a simple and reduced interrogation scheme. The performance of the FSS is assessed through post-calibration measurements compared to a commercial Fiber Bragg Grating (FBG) sensor, demonstrating comparable results. These findings pave the way for compact and portable fiber optic temperature sensing systems leveraging FSS advantages while maintaining compatibility with established fiber optic measurements.

This study aimed to use biomineralization technology to improve the bond strength of fiber-reinforced lightweight aggregate concrete (LWAC) after exposure to temperatures of 300 °C and 500 °C. The specimens of a control group (Group A) and two experimental groups (Group B and Group C) were prepared. These specimens healed themselves in different ways after exposure to high temperatures and pull-out tests. The self-healing method of Group A involved placing the specimen into an incubator. The self-healing method of Group B was the same as that of Group A. The self-healing method of Group C involved immersing the specimen in a mixed solution of urea and calcium acetate for two days, then taking it out and placing it in an incubator for two days. A cycle of four days was undertaken until the desired age was reached. After the specimens were healed to the planned age, the first and secondary pull-out tests and repair compound identification were carried out. After exposure to a temperature of 300 °C and self-healing for 90 days, compared with the specimens in Group A, the relative bond strength ratios of the secondary pull-out tests of the specimens in Group C increased by 20.3%. This indicates that biomineralization can effectively improve the bond strength of LWAC after high-temperature damage.

During carbonation process, the presence of water is an important parameter to accelerate this phenomenon. The carbon dioxide (CO₂) has been used as curing process production of fiber cement boards keeping the dimensional stability of cellulose fibers in cementitious matrix and promoting the CO₂ capture of environment. In addition, magnesium oxysulfate (MOS) cement has been used as another alternative binder to reduce the amount of CO₂ in the nature. The aim of this scientific paper is analysis the effect of rehydration method on the physical-mechanical properties of CO2-cured magnesium-based fiber cement boards. These boards were produced by Hatschek process simulation. The physical-mechanical performance and microstructural characteristics of MOS boards before and after carbonation were investigated by: water absorption (WA), apparent porosity (AP), and bulk density (BD); four-point bending test; X-ray diffraction (XRD); thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). According to the results, it was possible observe which the accelerated carbonation process resulted in improvements in the mechanical properties of the boards. The boards carbonated after 48 hours showed higher Modulus of Rupture values. The rehydration process of the composites before carbonation led to enhancements in the boards pre-cured for 48 and 72 hours, demonstrating that carbonation occurred more effectively after the supply of water through rehydration. The improvements in mechanical properties were associated with the formation of hydration products, which preferentially formed in the pores and voids of the fiber-cement. The presence of these carbonation products altered the physical properties of the materials, increasing the density of the boards and reducing the void volume. The decomposition of the formed carbonates was confirmed by thermogravimetric analysis, which indicated that the rehydration process favored the carbonation of the materials

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of their electrode materials. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to the advantages of high flexibility and bendability. However, it is still a big challenge to realize 1D flexible fiber lithium-ion batteries with excellent electro-chemical properties and good mechanical performance. In this work, a reduced graphene ox-ide-based printing ink is proposed to fabricate flexible Li4Ti5O12/graphene fiber electrodes through a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce graphene oxide in one step, which improved the conductivity of the fiber elec-trode. Furthermore, a 3D conductive network is constructed inside the fiber electrodes due to the high specific surface area of reduced graphene oxide, which enhances the electronic conductivity and ion mobility. The fiber electrode not only has good mechanical performance, but also has ex-cellent electrochemical properties. Equally important, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of fu-ture flexible electronic devices.

The calibration of length is related to the national economy and people's livelihood. The traditional calibration of length value was sent the uncalibrated instrument to the laboratory and the intrinsic error of the tested instrument was obtained in the laboratory. However, calibrating the instrument in the site produced additional error. In this article, a remote calibration method of length measurement based on optical fiber information transmission following with a proof of principle system was studied to reduce the additional error. The 1.0-level displacement guide rail was calibrated according to this method. The results showed that the relative error of guide rail displacement under different lengths was within 0.6%. The expanded uncertainties of 10 μm, 100 μm and 1 mm were analyzed respectively. The calibration results meet the actual standards of the guide rail. This optical method is a good candidate for remote calibration.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

In this paper, a sensitivity sensor of dual-core photonic crystal fiber (DC-PCF) filled with magnetic liquid is introduced and investigated by the finite element method (FEM). To regulate the energy coupling involving the two cores, the magnetic fluid is filled into the pore between the two cores. To adjust the coupling between the supermodes in the DC-PCF, the refractive index of the magnetic fluid-filled air hole may change due to the external magnetic field. This specifically created a magnetic fluid-filled DC-PCF, the magnetic fluid-filled hole is not used as the core for energy transmission, thus avoiding transmission loss. The dip wavelength and the magnetic field displayed an excellent linear connection between 80 and 260 Oe, depending on the numerical data. The detection sensitivity of the magnetic field reached 515.75 pm/Oe at a short fiber length of 482 m. The designed magnetic fluid-filled DC-PCF has high sensitivity and small volume and has great application prospects in medical and industrial field magnetic field detection.

The study presents the synthesis and characterization of dual-layer sulfonated polyphenylenesulfone (SPPSu) nanocomposite hollow fiber nanofiltration membranes incorporating titanium dioxide (TiO2) nanoparticles using the phase inversion technique. The newly developed membranes were systematically characterized using advanced tools and methods to evaluate their properties and performance. The study focused on investigating the effects of TiO2 addition in the SPPSu inner layer on pure water permeability, and salt rejection. The nanocomposite hollow fiber nanofiltration membranes exhibited a significant enhancement in pure water permeability, with a three-fold increase compared to the pristine membranes, achieving a flux of 5.4 L/m2h.bar. The addition of TiO2 also led to an improvement in the mechanical properties of the membranes, as evidenced by the increase in the expected tensile strength from 2.4 to 3.9 MPa. To evaluate the salt rejection performance, rejection tests were conducted using a laboratory-scale filtration setup in recycle mode. Aqueous solutions containing different divalent ions, specifically magnesium sulfate (Mg2SO4) and sodium sulfate (Na2SO4) at a concentration of 500 ppm, were used as the feed solution. The modified dual-layer hollow fiber nanocomposite membranes exhibited a maximal rejection of 95% for Mg2SO4, demonstrating their effective separation capabilities for divalent ions. The findings of this study highlight the successful synthesis and characterization of dual-layer SPPSu nanocomposite hollow fiber nanofiltration membranes incorporating TiO2 nanoparticles. The incorporation of TiO2 resulted in improved pure water flux, mechanical strength, and salt rejection performance. These enhanced properties make the developed nanocomposite membranes promising candidates for applications in nanofiltration processes, particularly for the selective separation of divalent ions from aqueous solutions.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

Guided ultrasonic waves are suitable for use in the context of structural health monitoring of thin-walled, plate-like structures. Hence, observing the wave propagation in the plates can provide an indication of whether damage has occurred in the structure. In this work, the wave propagation in fiber metal laminate consisting of thin steel foils and layers of carbon fiber-reinforced polymer is studied, focusing on the main propagation characteristics like dispersion diagrams and displacement fields. For this purpose, the dispersion diagrams derived from the analytical framework and numerical simulations are first determined and compared to each other. Next, the displacement fields are computed using the global matrix method for two excitation frequencies. The results derived from the analytical framework is used to validate numerically determined displacement fields based on a 2D and a 3D modeling approach. For both investigations the results of the analytical treatment and the numerical simulation show good agreement. Furthermore, the displacement field reveals the typical and well-known characteristics of the propagation of guided waves in thin-walled structures. Since the use of full 3D models involves a very high computational cost, this work also successfully investigates the possibility for model order reduction to decrease the computational time and costs of the simulation without the loss of accuracy.

With the ever-increasing rate, obesity has become an epidemiological problem throughout the globe comprising about 39% of the world population as of now. Among several reasons, disruption of the gut microbial ecosystem might contribute to the pathogenesis of metabolic disorders, including obesity, metabolic syndrome, type 2 diabetes, and other associated comorbidities. Though the mechanisms related to dysbiosis are unclear, diet might play a modulating role where different dietary approaches manipulate microbial richness and abundance as well as stability. For instance, shifting of Firmicutes and Bacteroidetes ratio in the gut might have a role in association with the dietary approaches and ingestion duration. Along with altered gut microbial composition, microbial metabolites such as short-chain fatty acids (SCFA) after ingestion of non-digestible dietary starches may have an impact on host metabolism by regulating lipogenesis, gluconeogenesis, and inflammation with potential associations to health and obesity. The dietary approaches like carbohydrates, fibre, protein, and/or fat diet at various arrangements can make a shift in the composition of gut microbiota if introduced for a short period. However, the unique pattern of the gut microbes usually remains the same along with the longer period of habitual diet. Though the short-term dietary intervention or circadian rhythm influences a transient change in gut microbes, other than habitual diet, the understanding related to long-term dietary change-induced permanent alterations is minimum. Alternatively, the usage of prebiotics, probiotics as well as postbiotics could be beneficial to overcome dysbiosis. This review highlights the current knowledge and the interaction between the human intestinal microbiota and diet as a modifying factor, in obesity allowing the scientists to uncover novel targets and tools to use as customized therapy.

We report world record high data transmission over standard optical fiber from a single optical source. We achieve a line rate of 44.2 Terabits per second (Tb/s) employing only the C-band at 1550nm, resulting in a spectral efficiency of 10.4 bits/s/Hz. We use a new and powerful class of micro-comb called soliton crystals that exhibit robust operation and stable generation as well as a high intrinsic efficiency that, together with an extremely low spacing of 48.9 GHz enables a very high coherent data modulation format of 64 QAM. We achieve error free transmission across 75 km of standard optical fiber in the lab and over a field trial with a metropolitan optical fiber network. This work demonstrates the ability of optical micro-combs to exceed other approaches in performance for the most demanding practical optical communications applications.

Azo dyes are the most widely used synthetic dyes in the printing and dyeing process. However, the discharge of untreated azo dyes poses potential threat for human health and aqueous ecosystem. Herein, we fabricated a novel heterogenous catalyst - activated carbon fiber-supported ferric alginate (FeAlg-ACF) . Together with peroxymonosulfate (PMS) and visible light, this photocatalytic oxidation system was used to remove an azo dye - azophloxine. The results indicated that the proposed catalytic oxidation system can remove 100% azophloxine within 24 min, while under the same system, the removal rate was only 92 % and 84 % when ferric alginate was replaced with ferric citrate and ferric oxalate respectively, which showed the superiority of activated carbon fiber-supported ferric alginate. The degradation of azophloxine is achieved by the active radicals (SO4•− and •OH) released from PMS and persistent free radicals from activated carbon fiber. After treating for 24 min, the total organic carbon of azophloxine solution (50 μmol/L) decreased from 1.82 mg/L to 79.3 μg/L and the nitrate concentration of ions increased from 0.3 mg/L to 8.6 mg/L. That is, up to 93.5% azophloxine molecules were completely degraded into inorganic compounds. Consequently, potential secondary contamination by intermediate organic products during catalytic degradation was prohibited. The azophloxine removal ratio was kept almost constant after seven cycles, indicating the recyclability and longevity of this system. Furthermore, the azophloxine removal was still promising at high concentrations of Cl-, HCO3-, CO32-. Therefore, our proposed system is potentially effective to remove dye pollutants from seawater. It provides a feasible method for the development of efficient and environmental friendly PMS activation technology combined with FeAlg-ACF, has significant academic and application value.

We experimentally demonstrate, for the first time, blind nonlinearity compensation using the Density-Based Spatial-Clustering of Applications with Noise (DBSCAN) algorithm for a 40-Gb/s 16-quadrature amplitude modulated being transmitted at 50 km of standard single-mode fiber. At high launched optical powers, DBSCAN offers up to 0.83- and 8.84-dB enhancement in Q-factor when compared to conventional K-means clustering and linear equalization, respectively.

Recently, the phase-sensitive OTDR (Φ-OTDR) based vibration sensor system has gained the focus of many researchers and some efforts have been undertaken to push further the limitations imposed on the performance of the Φ-OTDR sensor system. Then, progress in the different areas of its performance evaluation factors such as: improvement of the signal-to-noise ratio (SNR), spatial resolution (SR) in the sub-meter range, enlargement of the sensing range, frequency response bandwidth over the conventional limit and phase signal demodulation for quantitative measurement have been realized. This paper presents an overview of the recent progress in the Φ-OTDR based vibration sensing system in the different areas mentioned above.

In this paper, we investigate an animal-human cohabitation problem with the help of machine learning and fiber-wireless (FiWi) access networks integrating cloud and edge (fog) computing. We propose an early warning system which detects wild animals nearby road/rail with the help of wireless sensor networks and alerts passing vehicles of possible animal crossing. Additionally, we show that animals' detection at the earliest and the related processing, if possible, at sensors would reduce the energy consumption of edge devices and the end-to-end delay in notifying vehicles, as compared to the scenarios where raw sensed data needs to be transferred up the base stations or the cloud. At the same time, machine learning helps in classification of captured images at edge devices, and in predicting different time-varying traffic profiles-- distinguished by latency and bandwidth requirements-- at base stations, including animal appearance events at sensors, and allocating bandwidth in FiWi access networks accordingly. We compare three scenarios of processing data at sensor nodes, base stations and a hybrid case of processing sensed data at either sensors or at base stations, and showed that dynamic allocation of bandwidth in FiWi access networks and processing data at its origin leads to lowering the congestion of network traffic at base stations and reducing the average end-to-end delay.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

Fiber coupling efficiency is one of the key technical indicators of atmospheric laser communication, which directly affects the communication system BER. According to the optical fiber coupling efficiency model, the optical fiber coupling model under atmospheric slant link is established, and the relationship between wavelength, zenith angle, receiving aperture, altitude and coupling efficiency is studied through numerical simulation. Based on the principle of adaptive optics turbulence correction, the relationship between fiber coupling efficiency and adaptive optics order is established. A fast method for estimating the coupling efficiency based on Strehl ratio is proposed. According to the principle of laser communication system, the semi-physical simulation experimental system of atmospheric slant-range channel coupling efficiency is constructed, and the coupling efficiency test and analysis are completed.

In this study, divalent Yb2+-doped silica fiber was fabricated using rod-in-tube technology. The fiber core of Yb2+-doped silica glass was prepared by high-temperature melting technology under vacuum conditions. The spectroscopic properties of the Yb2+-doped glass and fiber were studied. The experiments indicate that divalent Yb2+-doped glass has a high quantum efficiency and superbroadband fluorescence in the visible region with an excitation wavelength of 405 nm. In additionally, the results suggest that Yb2+-doped fiber has a potential for application in visible fiber laser and fiber amplification.

The development of hybrid rockets offers excellent opportunities for the practical education of students at universities due to a high safety and a relatively low complexity of the rocket propulsion system. During the German educational program STERN, students of the Technische Universität Braunschweig obtain the possibility to design and launch a sounding rocket with a hybrid engine. The design of engine HYDRA 4X is presented and results of first engine tests are discussed. Results for measured regression rates are compared to results from literature. Furthermore, the impact of the lightweight casing material CFRP on the hybrid engine mass and flight apogee altitude is examined for rockets with different total impulse classes (10 to 50 kNs). It is shown that the benefit of a lightweight casing material on engine mass decreases with an increasing total impulse. However, a higher gain on apogee altitude, especially for bigger rockets with a comparable high total impulse is shown.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

The opened beams always confused the designers due to the guidelines missing. In this research, six hybrid reinforced beams reinforced with mixed steel and basalt fiber reinforced polymer (BFRP) bars had constant cross-sections of 150mm x 300mm and a clear span of 1800mm. Generally, five beams have symmetrical rectangular openings with dimensions of 150mm x 250mm located at a distance of 250mm (equivalent to the beam effective depth) from the beam support in addition to a solid beam that is served as a control reference. The studied parameters included the effect of using internal reinforcement (steel or BFRP bars) provided along the opening or by incorporating an external BFRP sheet around the opening corners. Also, the conduction of double enhancement with internal steel reinforcement bars further external strengthening BFRP sheet was investigated. The relevant results showed that the opened beam without enhancement lost almost 74.66% of the maximum load compared with the solid beam. Placing internal steel or BFRP bars around the openings increased the maximum load by 62.07% and 59.68%, respectively in comparison to the non-enhanced opened beams. Using an external BFRP sheet to strengthen the opening corners of the beam enhanced the maximum load by 76.39% compared with the non-enhanced opened beam. Therefore, if the beam double enhancement with an external BFRP sheet and internal steel reinforcement around the openings, the maximum load increased by 137.40% compared with the non-enhanced opened beam. Ultimately to further analyze the experimental results and confirm their findings, the study was extended to include the numerical analysis using three dimensional finite element modeling and the results correlated very well with the experimental ones.

In the past few decades, the use of agricultural waste has been increasing due to the increasing demand for sustainable materials. This paper aims to review the significance of agricultural waste as a type of wealth and its potential as an alternative material in the composite field. It was found that many agricultural wastes had been utilized in various production of ecological products. The review discusses the physical, mechanical, and chemical properties of the natural fibers made from agricultural waste and the use of Pineapple Leaf Fiber Reinforced Composite to manufacture UAVs (Unmanned Aerial Vehicles). The extracted waste fibers’ physical, mechanical, and chemical properties show that these agricultural wastes can produce better advanced composite materials suitable for structural applications. The use of pineapple leaf fiber in Unmanned Aerial Vehicles manufacturing has the potential to revolutionize this industry and contribute to a more sustainable future.

The sound and heat insulation are among the most important concerns in modern life and nonwoven composite structures are highly effective in noise reduction and heat insulation. In this study, three layered nonwoven composite structures composed of recycled polyester (r-Pet) based thermo bonded nonwoven outer layer and meltblown nonwovens from PP and PBT as inner layers were formed to provide heat and sound insulation. Fiber fineness and cross section of thermo bonded outer layer, fiber type (PP/PBT), areal weight (100/200g/m2) and process conditions (calendared/non-calendared) of meltblown inner layer have changed systematically and the influence of these parameters on thickness, bulk density, air permeability, sound absorption coefficient and thermal resistance of composite structures were analyzed statistically. Also; the results were compared with composite structures including electrospun nano fiber web inner layer and with structures without inner layer. It was determined that sound absorption coefficients ranging between 0.77-0.98 for moderate sound frequencies and 0.99-1 for higher sound frequencies were acquired with developed nonwoven composite structures. Besides, higher sound absorption coefficients were obtained as 0.71 and 0.74 for low sound frequencies such as 800 and 1000Hz, respectively. As a result of this study it can be concluded that developed nonwoven composite structures that provides better sound absorption coefficients and similar thermal conductivity values compared to previous studies and materials in the market can be used as insulation material in required areas.

This study aims to investigate the effect of banana stem fibers (BSFs) treatment with liquid smoke on changes in the micro-mechanics properties of BSFs, the tensile strength of single fibers, mor-phology, crystalline properties, and functional groups. The research used four model specimen variations, namely fiber without treatment and immersion in liquid smoke for 1, 2, and 3 hours. The BSFs with treatment was dried in an oven with a temperature of 40ºC for 30 minutes. Several tests were conducted, including a tensile test of single fiber capacity of 50N standard ASTM 3379-02, SEM observation, XRD, and FTIR test. The results showed that the highest increase in fiber strength was P2J, which was 264.21 MPa, and the lowest was TP fiber at 148.54 MPa. Fibers treatment with liquid smoke can form strong C-C elemental bonds caused by the H2O degradation process in BSFs, hence carbon atoms (C) are dense, and in conditions of excessive H2O degradation, the fiber strength will become brittle and the liquid smoke can increase the tensile strength of the fiber. The morphology of the fiber changed where the untreated fiber was covered with lignin, while the treated fiber had an elongated rectangular line pattern, porous, and the lignin was eroded. Crystalline properties in the X-ray diffractogram pattern differ between untreated and treated fibers. At an angle of 2ϴ, the lowest diffraction peak is around 160 in untreated wool, and the highest is 230 in treated fiber. The functional group of the fiber has changed where there is a difference in the wave crest between untreated and treatment fiber. The longer immersion time, the element of Carbon (C) will increase. In conclusion, treating BSFs with liquid smoke can change the physical, mechanical, and chemical properties, hence becoming a choice of composite reinforcement material in the future which is lightweight and environmentally friendly.

Rigid-hulled inflatable boats are extremely practical and popular nowadays. They offer a effective conciliation among usability and costs. Their stable and seaworthy behaviour is guaranteed by performing hydroplaning hulls coupled with unsinkable inflated tubes. At the same time, their design is often based on tradition and preconceptions. Rarely, the design assumptions are validated by the reality or, even, by deeper investigations. In this article, both numerical methods and experimental mechanics techniques are proposed as an essential way for supporting the designers in their decisive tasks. Three different situations are detailed where a numerical or an experimental approach shows its benefit inside the engineering design process: firstly permitting to investigate the behaviour of materials driving the fiberglass selection; then measuring the levels of stress and strain in the hull during sailing; finally, using all available information as a base for developing numerical models of the hull slamming in waves. Even if the discussion is focused on a rigid inflatable boat, large part of its considerations is relevant beyond this special case.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

This review aims to comprehensively synthesize the most recent research, collected from reputable databases, focusing specifically on transmission line. It examines advancements and challenges in data transmission. Fiber optics remains dominant, with new fiber designs and signal processing techniques like SDM improving capacity. Researchers are also addressing signal distortion and crosstalk. Beyond fiber optics, the review explores findings in coaxial cables and the promise of graphene for future high-speed transmission. Novel methods for mitigating crosstalk are presented. The findings highlight a trend towards more dependable, effective, and versatile transmission methods, with implications for various industries and electronic systems.

The current study presents a computational fluid dynamics model designed to simulate the isolation of 2D graphene components from their dispersion using a microfiltration hollow fiber membrane unit. The model utilizes Navier-Stokes and mass conservation equations to predict the flow and concentration behaviors in the system, and it employs the resistance-in-series approach to couple the fouling of the non-exfoliated graphites in the dispersion to the model. Specifically, the model accounts for the effects of the concentration polarization and cake formation of the fouling component, resulting in the increment of the transmembrane pressure (TMP) of the system. Additionally, we assumed the wettability of polymeric membrane’s inner wall enhances upon fouling by the flat layered structure material, leading to the reduction of the transmemrabe pressure. This approach demosntrates accurate reproduction of the exceptional experimental TMP behavior corresponding to the fouling of the graphite.

Turbidity is an important water quality parameter, especially for drinking water. The ability to actively monitor the turbidity level in Drinking Water Distribution Systems is of critical importance to the safety and wellbeing of the public. Traditional turbidity monitoring methods involve manual collection of water samples at set locations and times followed by laboratory analysis, which are labor intensive and time consuming. Fiber-optic measurement permits real-time, in-situ turbidity monitoring. But the current technology is based on plastic fibers, which suffer from high optical attenuation and hence are unsuitable for large-scale remote monitoring. In this paper, we report the demonstration of a fiber-optic turbidity sensor based on multi-mode glass fibers. The system uses a single fiber to both deliver laser light into the water sample and collect the back-scattered light for detection. A balanced-detection scheme is utilized to remove the common-mode noise to enhance the turbidity sensitivity. Highly linear turbidity responses are obtained and a turbidity resolution as low as 0.1 NTU is achieved. The test unit is also shown to have excellent reproducibility against repeated measurements and good stability against temperature changes. Turbidity measurement in real environmental matrices such as tap water and pond water is also reported with an assessment of the impact of flow rate. This work demonstrates the feasibility of future large scale distributed fiber-optic turbidity monitoring networks.

We present a novel method for online measurement of multi-point opening distances of midpalatal suture during rapid palatal expansion (RPE) using fiber optic Fabry-Perot (F-P) sensors. The sensor consists of an optical fiber with a cut flat end face and an optical reflector, which are implanted into the palatal base structure of an expander and is capable of measuring the precise distance between two optical reflective surfaces. As a demonstration, a 3D printed skull model containing the maxilla and zygomaticomaxillary complex (ZMC) was produced and a miniscrew-assisted rapid palatal expander (MARPE) with two guide rods was used to generate the midpalatal suture expansion. The reflected spectrums of the sensors were used to dynamically extract cavity length information for full process monitoring of expansion. The dynamic opening of the midpalatal suture during the gradual activation of the expander was measured, and a displacement resolution of 2.5 μm was demonstrated. The angle of expansion was derived and the results suggested that the midpalatal suture was opened with a slightly V type expansion of 0.03 rad at the first loading and subsequently expanded in parallel. This finding might be useful for understanding the mechanical mechanisms that lead to different types of expansion. The use of a fiber-optic sensor for mounting the rapid palatal expander facilitates biomechanical studies and experimental and clinical evaluation of the effects of RPE.

Rapeseed meal (RM) is an important agroindustrial by-product produced in large quantities by oil extraction from seeds. However, the efficient utilization of RM as animal feed is limited by its low metabolizable energy, poor palatability, and high levels of fiber and anti-nutritional components. Here, we investigate the potential of enriching RM with single-cell protein by fermentation with conventional and unconventional yeasts, to make a nutritionally improved feed component. The process of simultaneous saccharification and fermentation improved the parameters of the waste biomass, especially the protein content, the amount of crude fiber, and the degree of biotransformation of isoflavone compounds present in the waste material. Fermentation yielded the highest protein gain for the Saccharomyces cerevisiae Ethanol Red strain (ΔN=2.38%) at a biomass load of 12.5 g and for Scheffersomyces stipitis (ΔN=2.34%) at an enzyme dose of 0.125ml/10g DM. Crude fiber content (CF) was reduced by 2.55–7.18%. The SSF process resulted in the conversion of isoflavones to forms with fewer adverse effects and lower estrogenic activity.

In this paper, an all-fiber Mach-Zehnder interferometer (MZI) sensor for refractive index (RI) measuring is presented, which is based on Multimode–Single-mode–Multimode (MSM) fiber. The effects of both reducing the radius of the sensing part and the surface plasmon resonance (SPR) on its efficiency are investigated. Increasing the interaction of high-order modes with external media, caused by etching the cladding layer of the single-mode fiber part, significantly improves the sensitivity. Both wavelength and intensity interrogation approaches are employed to study the Multimode–etched Single-mode–Multimode (MESM) fiber sensor. The intensity and the wavelength sensitivities for the RI measurement in the range of 1.428-1.458 are obtained as -2308.92 %/RIU and 1313.14 nm/RIU, respectively. Finally, the MESM-SPR sensor is proposed and characterized. Results exhibit high performance in the RI range of 1.333 to 1.357, in which the sensitivity of 1433 nm/RIU is achieved. The advantages like low cost, high sensitivity, and simple fabrication methods make these sensors promising devices for chemical, food industry, and biosensing applications.

The bending performance of a basalt-polypropylene fiber-reinforced concrete (HBPFRC) was characterized by testing 24 400×100×100 mm3 prismatic specimens in a four-point bending test JSCE-SF4 configuration. The type and content of both fibers was varied in order to guarantee different target levels of post-cracking flexural performance. The results evidenced that mono-micro basalt fiber reinforced concrete (BFRC) allows the increase of the flexural strength (pre-cracking stage), while macro polypropylene fiber reinforced concrete can effectively improve both bearing capacity and ductility of the composite for a wide crack width range. Compared with the plain concrete specimens, flexural toughness and equivalent flexural strength of macro polypropylene fiber-reinforced concrete (PPFRC) and the hybrid fiber-reinforced concrete (HFRC) increased by 3.7~7.1 times and 10%~42.5%, respectively. From both technical and economic points of view, the optimal mass ratio of basalt fiber to polypropylene fiber resulted to be 1:2, with a total content of 6 kg/m3. This HFRC is seen as a suitable material to be used in sewerage pipes where cracking control (crack formation and crack width control) is of paramount importance to guarantee the durability and functionality of the pipeline as well as the ductility of the system in case of local failures.

This paper presents a numerical two-scale framework for the simulation of fiber reinforced concrete under impact loading. The numerical homogenization framework considers the full balance of linear momentum at the microscale. This allows for the study of microscopic inertia effects affecting the macroscale. After describing the ideas of the dynamic framework and the material models applied at the microscale, the experimental behavior of the fiber and the fiber-matrix bond under varying loading rates are discussed. To capture the most important features, a simplified matrix cracking and a strain rate sensitive fiber pullout model are utilized at the microscale. A split Hopkinson bar tension test is used as an example to present the capabilities of the framework to analyze different sources of dynamic behavior measured at the macroscale. The induced loading wave is studied and the influence of structural inertia on the measured signals within the simulation are verified. Further parameter studies allow the analysis of the macroscopic response resulting from the rate dependent fiber pullout as well as the direct study of the microscale inertia. Even though the material models and the microscale discretization used within this study are still simplified, the value of the numerical two-scale framework to study material behavior under impact loading is shown.

The distributed fiber optic strain measurement based on Rayleigh scattering has recently become increasingly popular in automotive or mechanical engineering for strain monitoring and in the construction industry, especially structural health monitoring. This technology enables the monitoring of strain along the entire fiber length. This article addresses integrating optical fibers of different coatings into the concrete matrix to measure the shrinkage deformations. However, previous studies do not give a clear statement about the strain transfer losses of fiber optic sensors in this application. In this context, three different coating types were investigated regarding their strain transfer. The fibers were integrated into fine-grained concrete prisms, and the shrinkage strain was compared with a precise dial gauge. The analysis shows a high correlation between the reference method and the fiber measurement, especially with the Ormocer coating. The used acrylate coating is also consistent in the middle area of the specimen but requires a certain strain introduction length to indicate the actual strain. The main result of this study is a recommendation for fiber coatings for shrinkage measurement in fine-grain concretes using the distributed fiber optic strain measurement. In addition, the advantages and disadvantages of the measurement method are presented.

Use of Machine Learning (ML) methodologies in optical communications has paved a new pathway. In this paper, firstly, we discuss the use of ML methodologies for reducing optical fiber nonlinearities, nonlinearity compensation, fault detection and optical performance monitoring. Then we present our recent work where we compare RL-SARSA and SVM based method with conventional method. The results show that RL-SARSA and SVM methods are successful candidates in mitigating the nonlinearities in proposed system as compared to conventional optical communication system.

Lightweight composite sandwich structures are laminated composite structures that are composed of thin stiff face sheets bonded to a thicker lightweight core in between. These structures have high potential to be used in marine, aerospace, defense and civil engineering applications due to their high strength to weight ratios and energy absorption capacity.In this study, composite sandwich structures were developed with carbon fiber reinforced polymer composite face sheets and aluminum honeycomb core materials with various thicknesses. Carbon fiber/epoxy composite face sheets were fabricated with lamination of [0/90]_s carbon fabrics by vacuum infusion technique. Al honeycomb layers were sandwiched together with the face sheets using a thermosetting adhesive. Mechanical tests were carried out to determine the mechanical behavior of face sheets, Al cores and the composite structure. Effect of core thickness on the mechanical properties of the sandwich was investigated.

Optical fiber sensors have become a widely-used tool to perform life-long monitoring of large structures. Different set-ups of sensors can be used to obtain information at different scopes. In this paper, the application of a portable Brillouin optical time domain analysis sensor applied to reinforced concrete beams is presented. The sensor is made up of a single-mode optical fiber applied to the structure that enables the measurement of tensile and compressive axial strain along the beams. The fiber is embedded into a concrete casting and fixed along the reinforcement bars so that a complete correlation can be obtained regarding strain and displacements in linear and non-linear flexural response. The use of four sensing fibers positioned along the beam's length at different vertical positions makes it possible to read the strain variation within the cross-section. In accordance with Bernoulli’s hypothesis, this allows curvature diagrams to be obtained across the structure. The measured curvature is used to set up the moment–curvature relationship, which highlights the possibility of the sensor monitoring structures continuously in space and time.

We study impact of geometry on leakage loss in negative curvature fibers made with As₂Se₃ chalcogenide and As₂Se₃ chalcogenide glasses for carbon dioxide (CO₂) laser transmission. The minimum leakage loss decreases when the core diameter increases both for fibers with six and for fibers with eight cladding tubes. The optimum gap corresponding to the minimum loss increases when the core diameter increases for negative curvature fibers with six cladding tubes. For negative curvature fibers with eight cladding tubes, the optimum gap is always less than 20 μm when the core diameter ranges from 300 μm to 500 μm. The influence of material loss on fiber loss is also studied. When material loss exceeds 10² dB/m, it dominates the fiber leakage loss for negative curvature fiber at a wavelength of 10.6 μm.

In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

Prestress loss evaluation in prestressed strand is essential for prestressed structures. However, the sensors installed outside the duct can only measure the total prestress loss. The sensors attached on strand inside the duct also have several problems, such as inadequate durability in an aggressive environment, vulnerable damage at tensioning and so on. This paper proposes a new installation method for long-gauge fiber Bragg grating (LFBG) sensor to prevent accidental damage. Then the itemized prestress losses were determined in each stage of the pre-tensioning and post-tensioning according to the LFBG measurements. We verified the applicability of the LFBG sensors for prestress monitoring and the accuracy of the proposed prestress loss calculation method during pre-tensioning and post-tensioning. In the pre-tensioning case, the calculated prestress losses had less deviation from the true losses than those obtained from foil-strain gauges, and the durability of the LFBG sensors was better than foil-strain gauges, whereas in post-tensioning case, the calculated prestress losses were close to those derived from theoretical predictions. Finally, we monitored prestress variation in the strand for 90 days. The itemized prestress losses at each stages of post-tensioning were obtained by the proposed calculation method to show the prospect of the LFBG sensors in practical evaluation.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

MATERIAL AND METHOD: This is an observational analytical cohort study carried out on a total of 160 patients, divided into 4 groups: healthy, with myopia, with primary open-angle glaucoma (POAG), and with POAG and myopia together. The study variables were Bruch's membrane opening area (BMO), the thickness of the RNFL and the RGC layer using the Glaucoma Premium program of the OCT Spectralis of Heidelberg. RESULTS: Regarding the analysis between age and the thickness of the RNFL, significant results were found in the healthy and glaucoma groups with myopia, for the rest of the groups, although there are no significant results, the correlation is negative, the older the younger is the thickness. Regarding intraocular pressure (IOP), significant results have been found in the nasal sector in the glaucoma group. In the glaucoma with myopia group, statistically significant results have been obtained when analyzing the thickness of the RNFL with refraction. In the analysis between the thickness of the RNFL and the RGC layer, significant results were obtained in the myopia and glaucoma groups; in the group of glaucoma with myopia, it occurs in the superior temporal sector. CONCLUSION: In the case of myopic patients with glaucoma, damage at the functional, both the thickness of the RNFL, the RCG and the BMO-MRW are greater than other groups. All these alterations can be evaluated and monitored with the OCT Spectralis thanks to the programs it includes, making this instrument one of the best for an early diagnosis of glaucoma and the damage produced in myopic patients.

The aim of this study was to develop a basic model to predict enteric methane emission from dairy cows and to update operational calculations for the national inventory in Norway. Basic models were developed using a database with 63 treatment means from 19 studies. The database included records for enteric CH4 production (MJ/day), dry matter intake (DMI), and dietary nutrient composition. The basic models were evaluated against an external database (n=36, from ten studies) along with other extant models. When evaluated by low root mean square prediction errors and high concordance correlation coefficients, the developed basic models that included DMI, dietary concentrations of fatty acids and neutral detergent fiber performed slightly better in predicting CH4 emissions than extant models. In order to propose country-specific values for the CH4 conversion factor Ym (% of gross energy intake partitioned into CH4) and thus to carry out the national inventory for Norway, the existing operational model was updated for the prediction of Ym over a wide range of feeding situations using energy corrected milk and dietary concentrate share as predictor variables. Input values of Ym were updated based on the results from the basic models. The predicted Ym ranged from 6.22 to 6.72%. In conclusion, the prediction of CH4 production from dairy cows was improved with the help of newly published data, which enabled an update of the operational model for calculating the national inventory of CH4 in Norway.

Erosion caused by the repeated impact of particles on a substance surface is a usual wear method resulting in gradual and continual loss of objects. It is a crucial problem in several modern industries because their surfaces are frequently subjected to destructive erosive situations. Polymers and their hybrid materials include several applications to be used as a coating in the form of powder for different applications. This review paper aims to provide extensive information on the erosion behavior of thermoset and thermoplastic neat resin and their hybrid materials composites. Focus is specifically paid to highlight the influence of properties of selected materials, impingnation parameters such as incident Angle of erodent, impact velocity of erodent, erodent nature, and the erosion mechanism. The review further extends the information about the erosion techniques and numerical simulation methods used for wear studies of surfaces. An investigation has been carried out for researchers to explore the selection of materials and methods in terms of conditions and parameters to meet the current and future needs and challenges for the protection of surfaces of the advanced industries. During review according to the findings achieved from the literature of the past fifty years, it has been noted that the thermoplastic nature of the composite is a key component to determine the anti-wear properties, the composites with lower glass transition, higher ductility, and greater crystallinity can provide better protection to erosion in advance surface applications.

The formation of a rigid tough interface based on a nacre-like structure in carbon fiber (CF) composites is a promising way to eliminate low delamination resistance. An effective method of coating CFs is electrophoretic deposition (EPD), which, in the case of dissimilar components like graphene oxide (GO) and polymeric glue, usually requires their chemical bonding/ strong interactions. In this work, we focus on chitin nanocrystals (ChNCs), leading to an excellent mechanical performance of artificial nacre, where favorable interactions and bonding with GO were controlled by degrees of deacetylation (5, 15 and 30 %). We have prepared coatings based on GO/ChNCs adducts with 95/5, 90/10,50/50 and 25/75 ratios using optimized EPD conditions (pH, concentration, voltage and time). The prepared materials were characterized using FTIR, TEM, XPS, SEM, DLS, and XRD. SEM evaluation indicates the formation of a homogeneous interlayer, which possesses a fair ability of chemical bonding with the epoxy matrix. Short beam testing of epoxy matrix composites indicates that coating does not decrease stiffness and its relatively low dependence on composition. Therefore, all coatings are promising for a detailed study of delamination resistance using laminate samples. Moreover, facile EPD from water solution/ suspension has a fair potential for industrial applications.

The incidence of celiac disease and gluten intolerance has been significantly rising globally. Gluten-free product consumption registered a sudden rise also among tolerant people, due to psychosocial factors. Biscuits are popular, low-cost bakery foods, consumed by nearly everyone worldwide. The removal of gluten from the baked product causes some undesirable traits and different textures and tastes. The main goal consists of creating a food product with the same taste and texture as a product with gluten. Moreover, gluten-free bakery products are usually low-grade sources of protein and poor in dietary fiber. Quinoa is a source of TDF and valuable protein. In this study, quinoa flour was used as the main constituent in the formulation of gluten-free c to improve their nutritional properties. Six different recipes with different percentages of quinoa flour have been realized. The formulations were compared, by rheological analysis, of each other and with a wheat flour control shortbread. The recipes with rheological features more similar to control shortbread were subjected to a discrimination analysis and the preferred was characterized from a chemical-physical and sensorial point of view. The experimental shortbreads constituted a good compromise to exploit the good nutritional composition of quinoa maintaining an acceptable sensory profile.

In the realm of power delivery to end-users, transformers are indispensable, with their malfunctions leading to substantial economic, safety, and environmental repercussions. The need for persistent surveillance is accentuated for in-situ oil-filled transformers, given the potential degradation of oil and the emergence of related ageing by-products. As the focus tilts towards online detection methodologies for transformer oil ageing, bypassing challenges associated with traditional offline methods such as sample contamination and misinterpretation, fiber optic sensors are gaining trac-tion due to their compact nature, cost-effectiveness, and resilience to electromagnetic disturbances typical in high-voltage environments. This work delves into the sensitivity analysis of intensi-ty-modulated plastic optical fiber sensors. The investigation encompasses key determinants such as the influence of optical source wavelengths, noise response dynamics, ramifications of varying sensing lengths, and repeatability assessments. Findings underscore that elongating the sensing length detrimentally affects both the linearity response and repeatability, largely attributed to the diminished resistance to external noise. Additionally, the choice of the optical source wavelength proved to be a critical variable in assessing sensor sensitivity.

The dispersion properties of surface plasmon polaritons during propagation on metal wires with a dielectric coating in the terahertz frequency range are investigated theoretically. An analytical expression is obtained for a pulsed electric field from the solution of Maxwell equations taking into account high-order dispersion terms. The effect of the dielectric coating on the distortion of the pulse shape is analyzed. Unlike uncoated wire, the propagation of a surface plasmon pulses along a coated wire is highly dispersive. It is shown that the coating leads to the appearance of a long-chirped signal with a propagation of only a few millimeters, i.e. when a terahertz pulse propagates along a coated wire, it acquires a long oscillatory tail, the frequency of which depends on time.

An experimental study was carried out to evaluate the ductility of reinforced concrete beams longitudinally reinforced with hybrid FRP-Steel bars. The specimens were fourteen reinforced concrete beams with and without hybrid reinforcement. The test variables were bars position, the ratio of longitudinal reinforcement, and the type of FRP bars. The beams were loaded up to failure using a four-point bending test. The performance of the tested beams was observed using the load-deflection curve obtained from the test. Numerical analysis using the fiber element model was used to examine the growth of neutral axis depth due to the effect of test variables. The neutral axis curves were then used to further estimate the neutral axis angle and neutral axis displacement index. The test results show that the position of the reinforcement greatly influences the flexural behavior of the beam with hybrid reinforcement. It was observed from the test that the flexural capacity of beams with hybrid reinforcement is 4% to 50% higher than that of the beams with conventional steel bars depending on bars position and the ratio of longitudinal reinforcement. The ductility decreases as the hybrid reinforcement ratio (Af/As) increases. This study also showed that a numerical model developed can predict the flexural behavior of beams with hybrid reinforcement with reasonable accuracy.

This paper reports the effect of silicon substrate orientation and aluminum nitride buffer layer deposited by molecular beam epitaxy on the growth of aluminum nitride thin films deposited by DC magnetron sputtering technique at low temperature. The structural analysis has revealed a strong (0001) fiber texture for both substrates Si (100) and (111) and a hetero-epitaxial growth on few nanometers AlN buffer layer grown by MBE on Si (111) substrate. SEM images and XRD characterization have shown an enhancement in AlN crystallinity thanks to AlN (MBE) buffer layer. Raman spectroscopy indicated that the AlN film was relaxed when it deposited on Si (111), in compression on Si (100) and under tension on AlN buffer layer grown by MBE/Si (111) substrates, respectively. The interface between Si (111) and AlN grown by MBE is abrupt and well defined; contrary to the interface between AlN deposited using PVD and AlN grown by MBE. Nevertheless, AlN hetero-epitaxial growth was obtained at low temperature (<250°C).

The epidermal cells on the surface of the cotton ovules undergo differentiation to produce fibers, which are single-celled hair-like protrusions resembling the plant trichomes. The initiation of these unicellular fibers from the cotton ovule surface is a complex and tightly regulated process. The initiation step is the cell fate-determining stage, which leads to the commitment of cells that eventually developed into fibers, thus becomes the most crucial phase in fiber development. The in-depth knowledge of molecular regulation is a prerequisite to get a clear view of the fiber initiation process's genetic and epigenetic control. The identification and functional validation of cotton fiber initiation-related genes, few fibreless mutants, transcription factors, microRNAs, epigenetic regulators, as well as the elucidation of the role of phytohormones as signaling molecules, has played a significant role in understanding the cotton fiber initiation process at the molecular level. This review focuses on the comprehensive information regarding the genetic and epigenetic regulation of cotton fiber initiation. Thus, the review will provide readers insight into mechanistic details that operate during cotton fiber initiation.

Flax fiber appears as a suitable feedstock in the endeavor of deploying a sustainable biobased economy. Its environmental performance as reinforcement in composite materials has been studied in previous Life Cycle Assessments (LCAs). However, these studies only present a coarse Life cycle Inventory (LCI) and often fail to detail all processes of the supply chain or to represent the co-products. This paper aims to bridge this gap and provide data for future LCAs on flax fiber production and transformation.The study focuses on the impacts of producing a bio-based reinforcement material (a fabric product for non-aesthetic purposes) with a system expansion perspective. The functional unit is defined as the production of 2400 m² flax-based technical textile per year, this corresponds to one hectare of cultivated land. The geographical scope considers that the production occurs in France and that some manufacturing process are outsourced in China. A Sensitivity Analysis was carried out to assess the influence of the electricity mix in the various countries involved in the manufacturing cycle.A detailed life cycle inventory for flax fiber production and transformation was built and the environmental performance of a flax technical textile was assessed as a cradle-to-gate LCA. The fate of co-products was documented and was shown to contribute to the reduction of the generated environmental impacts. Through a cradle-to-gate LCA, a broader understanding of the environmental performance of a flax-based technical textile was presented by including the valorization of co-products and a wider set of analyzed impact categories, going therefore beyond the existing state-of-the-art. Results show agricultural activities and electricity production to be the biggest contributors to the environmental impacts of flax technical textile; contributions due to land use changes were minor in comparison. Very specifically for this case study, a sensibility analysis showed the influence of an all-French production to be more efficient from an environmental point of view.

We present a distributed optical-fiber temperature sensor with enhanced sensitivity based on an Al-coated fiber using the Rayleigh backscattering spectra (RBS) shift in optical frequency-domain reflectometry (OFDR). The Al-coated sensing fiber with a higher thermal expansion coefficient compared to silica produces a strain-coupled shift in the RBS under an increase in temperature. This effect leads to an enhanced temperature sensitivity of the distributed measurement scheme. Our results revealed that the temperature sensitivity obtained using the Al-coated fiber in OFDR was ~56% higher relative to that of a single-mode fiber. Moreover, the minimum measurable temperature recorded was 1 °C with a spatial resolution of 5 cm.

The new climate law introduces a policy of sustainable construction, the assumption of which is the reduction of CO2 by the construction industry and the use of environmentally friendly materials, such as agricultural, mineral, and recycled waste, while limiting the consumption of natural resources. The article is a literature review that analyzes selected waste materials from various sectors of the economy that can be used as additives or partial substitutes for natural resources in the production of cement and in and cement building materials, the production of which reduces CO2 emissions, producing materials with high mechanical strength and environmentally friendly.

Hemoconcentration membranes used in cardiopulmonary bypass require a pore structure design with high pure water permeability, and which does not allow protein adsorption and useful protein loss. However, studies on hemoconcentration membranes have not been conducted yet. The purpose of this study was to analyze three-dimensional pore structures and protein fouling before and after blood contact with capillary membranes using the tortuous pore diffusion model and a scanning probe microscope system. We examined two commercially available capillary membranes of similar polymer composition that are successfully used in hemoconcentration clinically. Assuming the conditions of actual use in cardiopulmonary bypass, we perfused these membranes with bovine blood. Pure water permeability before and after bovine blood perfusion was measured using the dead-end filtration. The scanning probe microscopy system was used for analysis. High-resolution three-dimensional pore structures on the inner surface of the membranes were observed before blood contact. On the other hand, pore structures after blood contact could not be observed due to protein fouling. The pore diameters calculated by the tortuous pore diffusion model and scanning probe microscopy were mostly similar and could be validated reciprocally. Achievable pure water permeabilities showed no difference despite protein fouling, leading to low values of albumin SC. This is due to the mechanism that protein fouling occurs on the membrane surface, while there is little internal pore blocking. Therefore, controlling the fouling is essential for membranes in medical use. These characteristics of the hemoconcentration membranes examined in this study are suitable for clinical use.

The global textile sector, pivotal to economic development, significantly contributes to environmental degradation, prompting a shift towards sustainable raw material sources. Embracing circular economy principles, this industry is exploring the valorization of agricultural by-products. This study introduces an innovative approach to repurposing mango waste into valuable textile fibers, a byproduct of the fruit processing industry, predominantly generated during juice and jam production. The focus is on the lignocellulosic constituents of mango waste, specifically the peel, seed, and fibrous material, traditionally considered as refuse. Previous research has predominantly utilized mango peel in pectin extraction for food applications, whereas the potential of seed and fibrous content remains underexplored. This investigation endeavors to transform these fibrous by-products into high-value materials suitable for textile manufacturing. The process involved washing, drying, and comprehensive physicochemical characterization of mango fibers, emphasizing lignin quantification, revealing a composition of 12.2% lignin. An experimental design was employed to elucidate the impact of variables such as liquid-to-solid ratio, reaction duration, and sodium hydroxide concentration on lignin dissolution through alkaline hydrolysis. Optimal conditions—10% NaOH concentration, 30 mL/g liquid-to-solid ratio over six hours—achieved an 83% reduction in lignin content. The resulting fibers exhibited properties akin to conventional natural fibers, including a favorable aspect ratio indicative of their suitability for textile applications. A subsequent softening process using propylene glycol enhanced the fibers' spinability, producing a durable, textured fabric ideal for eco-conscious fashion applications, including bags, footwear, and accessories. This research demonstrates the feasibility of converting mango waste into a textile-worthy material and underscores the importance of waste revalorization in promoting sustainability within the circular economy framework.

This work describes a new transducer prototype for continuous monitoring both in the structural and geotechnical fields. The transducer is synthetically constituted by a wire of optical fiber embedded between two fiber tapes (fiberglass or carbon fiber) and glued by a matrix of polyester resin. The fiber optical wire ends have been connected to a control unit whose detection system is based on Brillouin optical time-domain frequency analysis. Three laboratory tests were carried out to evaluate the sensor's reliability and accuracy. In each experiment, the transducer was applied to a sample of inclinometer casing sets in different configurations and with different constraint conditions. The experimental data collected were compared with theoretical models and with data obtained from the use of different measuring instruments to perform validation and calibration of the transducer at the same time. Several diagrams allow comparing the transducer and highlighting its suitability for monitoring and maintenance of structures. The characteristic of the transducer suggests its use as a mixed system for reinforcing and monitoring, especially in lifetime maintenance of critical infrastructures such as transportation and service networks, and historical heritage.

The main objective of this this cross-sectional study was to analyze the influence of lifestyle fac-tors (diet, physical activity, sleep), which can affect the concentrations of fecal short-chain fatty acids (SCFAs) and SCFAs potential role in modulating cardiometabolic disease risk by interact-ing with biochemical and body composition parameters. The study comprised 77 healthy, non-obese individuals, aged 30-45 years who were assessed in the light of SCFAs concentration in stool, diet, physical activity level and sleep duration. Moreover, body composition measurement and patients’ biochemical parameters were included in the analysis. We have indicated a signifi-cant negative correlation between several SCFAs [especially acetic acid (AA), isobutyric acid (IBA), butyric acid (BA), isovaleric acid (IVA) and valeric acid (VA)] with BMI, VAT/SAT ratio (visceral to subcutaneous fat ratio) and percentage of fat mass in a group of females enrolled in the study as well as with waist circumference (WC) in case of both sexes included in the study. Moreover, the results of our study acknowledged the importance of a diet in shaping SCFAs pro-file - we noticed the significant negative associations between energy and fat intake and some SCFAs in males [IBA, IVA, VA, isocaproic acid (ICA)]. In terms of fiber intake, we noticed elevat-ed concentrations of vast majority of SCFAs and amount of SCFAs in total in case of both sexes included in the study. These strong correlations reflect the fact that diet shapes the composition of the gut microbiota and SCFAs (main microbial metabolites) are synthesized from dietary fiber. Furthermore, we noticed that in a group of women, the concentration of AA, propionic acid (PA) and ICA as well as the total concentration of SCFAs showed a significant positive association with their sleep duration. We concluded that SCFAs can have a potential role in modulating car-diometabolic disease risk by interacting with adiposity parameters and diet. In addition, this potential direct link between diet and SCFAs may at least partly contribute to sleep improvement.

Abstract: In recent years, the construction engineering sector has undergone a transformative shift towards the integration of machine learning (ML) techniques, particularly in predicting the properties of steel fiber-reinforced concrete (SFRC). Despite the theoretical sophistication of existing models, a persistent challenge remains – their opacity, lacking transparency and real-world relevance for practi-tioners. To address this gap and advance our current understanding, this study employs the extra gradient (XG) Boosting algorithm, crafting a comprehensive ap-proach. Grounded in a meticulously curated database drawn from 43 seminal pub-lications, encompassing 420 distinct records, this research focuses predominantly on three primary fiber types: crimped, hooked, and mil-cut. Complemented by hands-on experimentation involving 20 diverse SFRC mixtures, this empirical campaign is further illuminated through the strategic use of Partial Dependence Plots (PDPs), revealing intricate relationships between input parameters and con-sequent compressive strength. A pivotal revelation of this research lies in the identification of optimal SFRC formulations, offering tangible insights for real-world applications. The developed ML model stands out not only for its sophistication but also its tangible accuracy, evidenced by exemplary performance against inde-pendent datasets, boasting a commendable mean target-prediction ratio of 99%. To bridge the theory-practice gap, we introduce a user-friendly digital interface, thri-ughly designed to guide professionals in optimizing and accurately predicting the compressive strength of SFRC. This research thus contributes to the construction and civil engineering sectors by enhancing predictive capabilities and refining mix designs, fostering innovation, and addressing the evolving needs of the industry.

This paper examines the quantitative and qualitative situation of the current fixed and mobile Internet and its expected future. First, the number of users and penetration rate of the Internet, various types of services in different countries, the ranking of countries in terms of the mean and median download and upload Internet data speeds, Internet data volume, and number and location of data centers in the world are presented. The second task introduces and details twelve performance evaluation metrics for broadband Internet access. Third, different wired and wireless Internet technologies are introduced and compared based on data rate, coverage, type of infrastructure, and their advantages and disadvantages. Based on the technical and functional criteria, in the fourth work, two popular wired and wireless Internet platforms, one based on optical fiber and the other based on the 5G cellular network, are compared in the world in general and Australia in particular. Moreover, this paper has a look at Starlink as the latest satellite Internet candidate, especially for rural and remote areas. The fifth task outlines the latest technologies and emerging broadband Internet-based services and applications in the spotlight. Sixthly, it focuses on three problems in the future Internet in the world, namely the digital divide due to the different quality of the Internet and new Internet-based services and applications of emerging technologies, the impact of the Internet on social interactions, and hacking and insecurity on the Internet. Finally, some solutions to these problems are proposed.

This research is completed in development of researches devoted to relations between elastic modulus (MoE) and thermal expansivity (CTe) of different materials. This study experimentally confirmed the relation of MoE and CTe for thermosetting polymers and FRPs both under normal and heating temperatures. As the thermosetting polymers, the epoxy compositions were used and glass fiber and mineral additives for FRP. The experiment was based on dilatometric and elastic deformations’ testing. Also, the relaxation model of MoE/CTe was proposed, that is based on physical properties of polymers’ supramolecular structures. The comparative analyzing of MoE/CTes’ different models is done. The most accurate models are determined, and the relaxation model has demonstrated the high accuracy.

This study investigated the anatomical characteristics and pulp quality of tapped Styrax sumatrana wood to facilitate its further utilization. The transverse surface of the tapped S. sumatrana was light or greyish brown in the sapwood and reddish brown in the heartwood. The resin canals of the tapped wood were formed along the growth rings at the boundaries between the heartwood and sapwood. Furthermore, microscopic analyses revealed an irregular outline and rounded epithelial cells at the edges of the intercellular traumatic resin canal (TC). Approximately 8–16 epithelial cells surrounded the resin canals. The fibers in the tapped S. sumatrana were generally thin-walled, whereas those near the TC were thick-walled. Moreover, S. sumatrana were diffuse-porous and exhibited intermediately distinct or indistinct growth ring boundaries. The vessels were mainly in radial multiples and clusters of 3–5. In addition, they showed a diagonal-to-radial pattern arrangement and a few tangential bands. Deposits were observed in some vessels in the tapped part but were absent in the untapped part. The fiber length of the tapped S. sumatrana wood was classified as moderate to extensive and categorized as 2nd grade pulp quality. Finally, the cell walls were classified as thin to moderate.

The initiation of micro-cracks in concrete is primarily due to its brittleness, which causes severe impacts on the overall behavior of the concrete. However, incorporating fibers in concrete could significantly improve its mechanical properties. The current study demonstrates the influence of two types of fibers on the mechanical properties of concrete. Nylon Fiber Threads (NFT) and Nylon Fiber Strands (NFS) at a fiber content of 2.5 kg/m³ were incorporated in the concrete mix. Concrete with a compressive strength of 30 MPa and a water-cement ratio of 0.4 was produced to investigate the fresh and mechanical properties of conventional and nylon-fiber reinforced concrete (NFRC). The concrete prims and cylinders were tested for compressive, splitting, and flexural strength using ASTM standards (ASTM C-39, C-496, and D-790, respectively). It was found that NFT-reinforced samples achieved higher mechanical properties of concrete (13.05%) compared to NFS-reinforced samples. Test results showed that incorporation of nylon fibers (NF) in concrete decreased the compressive strength of cylindrical and cubical specimens by 0–10% and 5–15%, respectively. However, it increased the splitting tensile and flexural strengths by 0-15%, and 5-15% respectively. Furthermore, the incorporation of NF in concrete significantly improved the ductility and delayed the crack initiation in concrete.

Three carbon-chain extension genes associated with fatty acid synthesis in cotton, namely GhKAR, GhHAD, and GhENR, play important roles in oil accumulation in cotton seeds. In the present study, these three genes were cloned and characterized. The expression patterns of GhKAR, GhHAD and GhENR in the high seed oil content cultivars 10H1007, 10H1014, and 10H1041 differed somewhat compared with those of 2074B with low seed oil content at different stages of seed development. GhKAR showed all three cultivars showed higher transcript levels than that of 2074B at 10, 40 and 45 DPA. The expression pattern of GhHAD showed a lower transcript level than that of 2074B at both 10 and 30 DPA but higher transcript level than that of 2074B at 40 DPA. GhENR showed a lower transcript level than that of 2074B at both 15 and 30 DPA. The highest transcript levels of GhKAR and GhENR were detected at 15 DPA in 10H1007, 10H1014, and 10H1041 compared with 2074B. From 5 to 45 days post anthesis (DPA) cotton seed, the oil content accumulated continuously in the developing seed. Oil accumulation reached the peak at 40 DPA to 45 DPA and slightly decreased in mature seed. In addition, GhKAR and GhENR showed different expression patterns in fiber and ovule development processes, in which they showed high expression levels at 20 DPA during fiber elongation stage, but their expression level peaked at 15 DPA during ovule development processes. These two genes showed the lowest expression levels at the late seed maturation stage, while GhHAD showed peak at 10 DPA of fiber development. Compared to 2074B, the oil contents of GhKAR and GhENR overexpression lines increased 1.05~1.08 folds. These results indicated that GhHAD, GhENR and GhKAR were involved in both seed oil synthesis and fiber elongation with dual biological functions in cotton.

In kidney, epithelial barrier has diverse functions in body fluid and electrolyte homeostasis, and urine production. Maintaining epithelial integrity fundamentally builds up physiological functionality of the renal epithelial barrier (REB). Specially, the REB) states regularly in osmotic dynamics. The osmotic dynamics gives rise of osmotic pressure that is a physical force. Overloading of osmotic pressure can crack epithelial integrity and damage REB. How REB endures the osmotic pressure force yet remains enigmatic. LMO7 (LIM domain only 7) is a protein associated with cell-cell junctional complex and cortical F-actin. LMO7 upregulation was observed in cells cultured in hypertonic condition. In kidney, LMO7 predominantly distributes in epithelial cells in renal tubules. Hypertonic stimulation leads to assembly of LMO7 and F-actin in cortical stress fibers in renal epithelial cells. Hypertonic-isotonic alternation as pressure force pushing plasma membrane inward/outward was set as osmotic disturbance and was applied to test FAK signaling and LMO7 functioning in maintaining junctional integrity. Along with junctional integrity, LMO7 depleted cells resulted in loss of junctional integrity in the epithelial sheet cultured hypertonic medium or hypertonic-isotonic alternation. On the other hand, FAK inhibited by PF-573228 leads to failure in robust cortical F-actin assembly and association of LMO7 with cortical F-actin in epithelial cells responding upon hypertonic stress. Epithelial integrity in context of osmotic stress, LMO7 and FAK signaling both involves in assembling robust cortical F-actin and maintaining junctional integrity. The LMO7 elaborately manages FAK activation in renal epithelial cells, which was evidently demonstrated in NRK-52E cells who have excessive FAK activation and lost epithelial integrity when cells with LMO7 depletion exposed to hypertonic environment. Our data suggests that LOM7 manages FAK activation and is responsible for maintaining REB under osmotic disturbance.

This study presents of the microsphere-based fiber-optic sensor with the ZnO ALD coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100°C to 300°C, with a 10°C step. The interferometric signal is used to control whether the microstructure is intact. Spectrum shift of a reflected signal is used to conclude changes in measured parameter for the sensor with a 100 nm coating, while the reflected signal intensity is an indicator during measurements executed by a sensor with a 200 nm coating. With changing temperature, the peak position or intensity of a reflected signal also changes. The R2 coefficient of the presented sensors indicates a linear fit of over 0.99 to the obtained data. The sensitivity of the sensors, investigated in this study, equals 103.5 nW/°C and 0.019 nm/°C for ZnO thickness of 200 nm and 100 nm, respectively.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

The hydrodynamic behavior of the air-acetic acid system in a bubble column is studied using a differential pressure transmitter, double probe optical fiber probe, and the electrical resistance tomography (ERT) technique. The superficial gas velocity ranges from 0.016 to 0.094 m/s under ambient temperature and pressure. The influences of viscosity and surface tension on gas holdup, bubble rising velocity, and bubble chord distribution in the column are discussed with different mass fractions of an acetic acid solution. The results show that as the mass fraction of acetic acid increases, the surface tension of the liquid phase decreases, and the viscosity first increases and then decreases. This causes the gas holdup in the column to first increase and then decrease, and reaches the maximum value at an acetic acid mass fraction of 55% to 60%. The rising velocity of the bubbles in the column is high in the central region and has a low-value distribution near the wall. The bubble chord length distribution is concentrated, and the distribution of the bubble chord length in the column becomes narrow with any decrease in surface tension. Studying the hydrodynamic behavior of a bubble column with the air-acid system is of great significance considering the absence of data on air-organic acid systems.

One-dimensional shape memory polymer fibers (SMPFs) have obvious advantages in mechanical properties, dispersion properties and weavability. In this work, a method for fabricating semi-crystallization ethylene-vinyl acetate copolymer (EVA) fiber with two-way shape memory effect by melt spinning and ultraviolet (UV) curing was developed. Here, the effect of crosslink density on its performance was systematically analyzed by gel fraction measurement, tensile tests, DSC and TMA analysis. The results showed that the crosslink density and shape memory properties of EVA fiber could be facilely adjusted by controlling UV curing time. The resulting EVA fiber with cylindrical structure had a diameter of 247.13 ± 10.07 μm, and its mechanical strength and elongation at break were 64.46 MPa and 114.33%, respectively. The critical impact of the crosslink density and applied constant stress on the two-way shape memory effect were analyzed. Moreover, the single EVA fiber could lift more than 143 times its own weight and achieve 9% reversible actuation strain. The reversible actuation capability was significantly enhanced by a simple winding design of the single EVA fiber, which provided great potential applications in smart textiles, flexible actuators and artificial muscles.

In this paper, a novel pendulum-type accelerometer based on hetero-core fiber optics has been proposed for structural health monitoring targeting large-scale civil infrastructures. Vibration measurement is a non-destructive method for diagnosing the failure of structures by assessing natural frequencies and other vibration patterns. The hetero-core fiber optic sensor utilized in the proposed accelerometer can serve as a displacement sensor with robustness to temperature changes in addition to immunity to electromagnetic interference and chemical corrosions. Thus the hetero-core sensor inside the accelerometer measures applied acceleration by detecting the rotation of an internal pendulum. A series of experiments showed that the hetero-core fiber sensor linearly responded to the rotation angle of the pendulum ranging within ±5°, and furthermore the proposed accelerometer could reproduce the waveform of input vibration in a frequency band of several Hz order.

Fiber-metal laminates (FMLs) such as Kevlar reinforced aluminum laminate (ARALL), Carbon reinforced aluminum laminate (CARALL), and Glass reinforced aluminum laminate (GLARE) offer great potential for weight reduction applications in automobile and aerospace construction. In order to investigate the feasibility for utilizing such materials in the form of laminates, sheet hydro-bulging tests are studied under the condition of uniform blank holder force for three-layered aluminum and aluminum-composite laminates using orthogonal carbon and Kevlar as well as glass fiber in the middle. The experimental results validate the finite element results and they exhibited that the forming limit of glass fiber in the middle is the highest among the studied materials, while carbon fiber material performs the worst. Furthermore, the crack modes are different for the three kinds of fiber materials investigated in the research. This study provides fundamental guidance for the selection of multi-layer sheet materials in the future manufacturing field.

It is necessary to address the scarcity of crushed stones for pavement structural layers. So fly ash can be proved to be promising solution as more than 270 tonnes of fly ash is generated in India. Though, numerous research has been conducted for the use of fly ash intreated and untreated form, high volume of fine particles and brittleness of the stabilized fly ash pose a great problem for its use in subbase and base. Moreover, stiffness or modulus of stabilized fly ash is vital elastic parameter which is used for mechanistic pavement design. Hence, in this study an extensive experimental investigation is carried out to study its strength and stiffness properties such as compressive strength, indirect tensile strength and flexural strength, cyclic indirect tensile modulus and flexural modulus of fiber reinforced cement stabilized fly ash, stone dust, aggregate mixtures. The stone dust and aggregates have been added to enhance the gradation of the composite’s mixture. The study presents the effect of fiber on strength and stiffness properties. The experimental result reveals that addition of polypropylene (PP) fibers up to 0.25 wt.% enhances the compressive strength and any further addition of fiber results in decrease of the strength. However, indirect tensile strength and flexural strength increases with increase in fiber percentage up to 0.5 wt.%. Cement content is observed to be the dominant parameter for stabilized materials. Suitable relationships have been developed between strength and modulus parameters for stabilized mixtures. Based on the strength and stiffness study, 70% fly ash and 30% stone dust-aggregate and 60% fly ash and 40% stone dust-aggregate with 6% cement can be considered for the base layer. Based on the indirect tensile strength and flexural strength behavior, 0.35% is considered as the optimum fiber percentage.

How do sensor research and technologies grow over time? This paper applies the network analysis with a new computational approach to map the structure and evolution of sensor research and technologies over a 30-year time frame (1990-2020).The goal of this study is to analyze the evolution of sensor research for forecasting emerging scientific and technological trajectories. Results show that the scientific interaction within ecosystem (represented with networks) of sensor generates a co-evolution of scientific fields supporting the accelerated growth of different technological tra-jectories, such as: wireless sensors, fiber optic and optical sensors, gas sensors and biosensors. These results suggest main theoretical implications that explain the evolution of sensor research with critical aspects of innovation management to support R&D investments towards new technological trajectories having a high potential of growth.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

Surface-enhanced Raman spectroscopy (SERS) can boost the pristine Raman signal by ~ 108 times that could be exploited for producing innovative sensing devices with advanced properties. However, the inherent complexity of SERS systems restricts their further applications in rapid detection, especially in situ detection in narrow aera. Here, we construct an efficient and flexible SERS-based LOP sensor by integrating Ag/Au nanocap arrays obtained by Ag/Au coating polystyrene nanospheres on the optical fiber face. We obtain rich “hotspots” at the nanogaps between neighboring nanocaps and further achieve the excellent SERS performance with the assistance of laser induced thermophoresis on the metal film that can achieve high efficiency aggregation of detected molecules. We achieve a high Raman enhancement with a low detection limitation of 10-7 mol/L for the most efficient samples based on the above sensor. This sensor also exhibits good repeatability and stability under multiple detections, revealing the potential application in situ detection based on the reflexivity of optical fiber.

Upcycling recycled carbon fibers recovered from waste carbon composites can reduce the price of carbon fibers while improving disposal-related environmental problems. This study assessed and characterized recycled carbon fibers subjected to sizing treatment using N-(2-aminoethyl)-3-aminopropyltrimethoxysilane (APS) chemically coordinated with polyamide 6 (PA6) and polypropylene (PP) resins. Sizing treatment with 1 wt.% APS for 10 s yielded O=C-O on the surface of the carbon fiber, and the -SiOH in the APS underwent a dehydration-condensation reaction that converted O=C-O (lactone groups) into bonds of C-O (hydroxyl groups) and C=O (carbonyl groups). The effects of C-O and C=O on the interfacial bonding force increased to a maximum, resulting in an oxygen-to-carbon ratio (O/C) of 0.26. The polar/surface energy ratio showed the highest value of 32.29% at 10 s, and the interfacial bonding force showed the maximum value of 32 MPa at 10 s, which is about 15% better than that of commercial carbon fiber (PA6-based condition). In 10-s resizing treatments with 0.5 wt.% 3-methacryloxypropyltrimethoxysilane (MPS), C-O, C=O, and O=C-O underwent a dehydration-condensation reaction with -SiOH, which broke the bonds between carbon and oxygen and introduced a methacrylate group (H2C=C(CH3)CO2H), resulting in a significant increase in C-O and C=O, with an O/C of 0.51. The polar/surface free energy ratio was about 38% at 10 s, with the interfacial bonding force increasing to 27% compared to commercial carbon fiber (PP-based conditions). The MPS exhibited a superior interfacial shear strength improvement, two times higher than that of APS, with excellent coordination with PP resin and commercial carbon fiber, although the interfacial bonding strength of the PP resin was significantly lower.

With a view to sustainable development and circular economy, this work focused on the possibility to valorize a secondary waste stream of recycled carbon fiber (rCF) to produce a 3D printing usable material with PA6,6 polymer matrix. The reinforcing fibers implemented in the present research are the result of a double recovery action: starting with pyrolysis from which long fibers are obtained, used to produce non-woven fabrics and, subsequently, fiber agglomerate wastes obtained from this last process are ground in a ball mill. The effect of a different amount of reinforcement at 5% and 10% by weight on the mechanical properties of 3D printed thermoplastic composites was investigated. Although the recycled fraction was successfully integrated in the production of filaments for 3D printing and therefore in the production of specimens via Fused Deposition Modeling technique, the results showed that fibers did not improve the mechanical properties as expected, due to an unsuitable average size distribution and the presence of a predominant dusty fraction ascribed to the non-optimized ball milling process. PA6,6 + 10 wt.% rCF composites exhibited a tensile strength of 59.53 MPa and a tensile modulus of 2.24 GPa, which correspond to an improvement in mechanical behavior of 21 5 % and 5 21 % compared to the neat PA6,6 specimens, respectively. The printed composite specimens loaded with the lowest content of rCF provided the greatest improvement in strength (+ 9% over the neat sample). Then, a prediction of the “optimum” critical length of carbon fibers was proposed that could be used for future optimizations of the recycled fiber processing.

In this paper, possibilities for the bandwidth and wavelength utilization in future next-generation passive optical networks are presented and reasons for realizing and utilizing of extended dynamic wavelength and bandwidth algorithms for NG-PON2 networks are analyzed. Next, principles of the effective dynamic bandwidth allocation are introduced in details, focused on the importance of the decision criterion optimization. For achieving better bandwidth utilization of dedicated wavelengths, this paper is focused on the novel effective dynamic bandwidth allocation algorithm with adaptive allocation of wavelengths to ONU units and on the optimization of the decision criterion. For analyzing the novel extended DWBA algorithm utilizing for various wavelength allocation cases possible in NG-PON2 networks, a simulation program with the enhancement of the EDBA algorithm is realized. Finally, an optimization of the decision criterion defining a minimum bandwidth utilization of the actual wavelength is executed for NG-PON2 networks based on the hybrid TWDM technique.

Reconstruction of acoustic relaxation absorption curve is a powerful approach to ultrasonic gas sensing, but requires known of a series ultrasonic absorption at various frequencies around effective relaxation frequency. Ultrasonic transducer is a most widely deployed sensor for ultrasonic wave propagation measurement and works only at a fixed frequency or specific environment like water, so a large number of ultrasonic transducers operating at various frequencies are required to recover an acoustic absorption curve with a relative large bandwidth, which cannot suit for large-scale practical applications. This paper proposes a wideband ultrasonic sensor using a distributed Bragg reflector (DBR) fiber laser for gas concentration detection through acoustic relaxation absorption curve reconstruction. With a relative wide and flat frequency response, the DBR fiber laser sensor measures and restores a full acoustic relaxation absorption spectrum of CO2 using a decompression gas chamber between 0.1 and 1 atm to accommodate the main molecular relaxation processes, and interrogates with a non-equilibrium Mach-Zehnder (M-Z) interferometer to gain a sound pressure sensitivity of -45.4 dB. The measurement error of the acoustic relaxation absorption spectrum is less than 1.32%.

The interfacial interface between the fibers and the matrix plays a key role for epoxy matrix composites and short recycled randomly arranged fibres. This study used short recycled carbon fiber (RCF) as a filler. Plasma treatment was used for carbon fiber surface treatment. This treat-ment was performed using radio (RF) and microwave (MW) frequencies at the same pressure and atmosphere. Appropriate chemical modification of the fiber surfaces helps to improve the wettability of the carbon fibers and, at the same time, allows the necessary covalent bonds to form between the fibers and the epoxy matrix. The effect of the plasma treatment was analyzed and confirmed by XPS analysis, Raman microscopy, SEM, TEM and wettability measurements. Composite samples filled with recycled carbon fibers with low concentrations (1 wt%, 2.5 wt% and 5 wt%) and high concentrations (20 wt% and 30 wt%) were made from selected treated fi-bers. The mechanical properties (impact toughness, 3PB) were analyzed on these samples. It was found that the modulus of elasticity and bending stress increase with the increasing content of recycled carbon fibers. A more significant change in impact strength occurred in samples with low concentration.

The article analyzes existing materials and structures with quadratic-nonlinear optical properties that can be used to generate a difference frequency in the terahertz and sub-terahertz frequency ranges. The principle of constructing a nonlinear optical-radio converter, based on an optical focon (a focusing cone), is proposed. Based on the assumption that this focon can be implemented from the metal-organic framework (MOF), we propose a technique for modeling its parameters. The mathematical model of the process of propagation and nonlinear interaction of waves inside the focon is based on a simplification of the nonlinear wave equation. Within the framework of the developed model, the following parameters are approximately determined: the 3D gradient of the linear refractive index and the function determining the geometric profile of the focon, which provide a few-mode-based generation of the difference frequency.