Introduction: Pharmaceutical tablets are solid forms administrated orally and they constitute 80% of the market because of its best stability and ease of large-scale production, adherence and treatment. The Brazilian Legislation establishes that for a drug to be registered as a similar or generic drug is necessary to verify the pharmaceutical equivalence in relation to the reference drug, indicated by ANVISA, through quality control tests, ensuring that the drug is approved with satisfactory quality. Objective: to evaluate the reference, generic and similar glibenclamide tablets through quality control tests, comparing the results with each other and relate clinical impacts on the patient in the face of changes in the quality control of medicines. Methodology: tests of average weight, friability and disintegration were done, according to the Brazilian Pharmacopoeia VI Edition, in uncoated tablets of Glibenclamide 5mg Reference (Daonil), Generic (Glibenclamide) and Similar (Glionil), and the results obtained were compared with the that advocates the scientific literature. Results: Data referring to the average weight: Reference 0.1591g, Generic 0.1002g and Similar 0.0996g; For friability: Reference value 0.54%, Generic value 0.49% and Similar value 0.28%. The disintegration tests showed the following times: Reference 35 seconds, Generic 29 seconds and Similar 33 seconds. Conclusion: the tests to which the glibenclamide tablets were submitted showed results within the parameters established by the Brazilian Pharmacopoeia.

Introduction: The aim of this study was to prospectively evaluate parents’/guardians’ late recall of surgical procedures and risks of elective surgery after pre-operative interview with surgeons. Materials and Methods: All parents/guardians of patients <18 years of age undergoing elective procedures from January 15th to September 1st, 2022, were prospectively enrolled in the study. Before discharge, parents/guardians were asked to complete a questionnaire regarding the duration of the consent procedure, duration of the interview, quality of the informative handouts, and their ability to recall the type of disease, type of surgical procedure, and surgical risks. Answers were graded from 1 to 4. Results: One hundred and two questionnaires were returned. In all cases, informed consent was obtained between 24 and 72 hours prior to surgery. The following responses were collected: 98/102 (96%) parents/guardians reported that the duration of the consent process was adequate; 95/102 (93%) reported that the handouts were fully informative, and 7/102 (7%) reported that they were partially informative regarding explanation of the disease and surgical procedure; regarding complications, 93/102 (91%) perceived the handouts to be fully/partially informative, while 4/102 (4%) perceived the handouts to be poorly/non-informative, and 5/102 (5%) did not provide a response; 94/102 (92%) stated that they remembered the pathology, but only 87/94 (93%) recalled it correctly; 90/102 (88%) stated that they remembered the type of procedure, but only 76/90 (84%) recalled it correctly; and 53/102 (52%) stated that they remembered the surgical risks, but only 20/53 (38%) could recall more than one complication. Conclusions: Late recall of surgical complications by parents was poor despite the high perceived quality of the surgical risk handouts and medical interview.

This study provides a unique procedure for validating and reconstructing temperature and precipitation data. Although developed from data in Middle Italy, the validation method is intended to be universal, subject to appropriate calibration according to the climate zones analysed. This~research is an attempt to create shared applicative procedures that are most of the time only theorized or included in some software without a clear definition of the methods. The purpose is to detect most types of errors according to the procedures for data validation prescribed by the World Meteorological Organization, defining practical operations for each of the five types of data controls: gross error checking, internal consistency check, tolerance test, temporal consistency, and~spatial consistency. Temperature and~precipitation data over the period 1931--2014 were investigated. The~outcomes of this process have led to the removal of 375 records (0.02%) of temperature data from 40 weather stations and 1286 records (1.67%) of precipitation data from 118 weather stations, and 171 data points reconstructed. In conclusion, this work contributes to the development of standardized methodologies to validate climate data and provides an innovative procedure to reconstruct missing data in the absence of reliable reference time series.

The aim of this paper is to present a comprehensive overview of the main aims and scopes in screening of botanicals, a task which thin-layer chromatography (TLC) is on an everyday basis confronted with and engaged in. Stunning omnipresence of this modest analytical technique (both in its standard format (TLC) and the high-performance one (HPTLC), either hyphenated or not) for many analysts might at a first glance appear chaotic and random, with an auxiliary rather than leading role in research, and not capable of issuing meaningful final statements. Based on these reflections, our purpose is not to present a general review paper on TLC in screening of botanicals, but a blueprint rather (illustrated with a selection of practical examples), which highlights a sovereign and important role of TLC in accomplishing the following analytical tasks: (i) solving puzzles related to chemotaxonomy of plants, (ii) screening a wide spectrum of biological properties of plants, (iii) providing quality control of herbal medicines and alimentary and cosmetic products of biological origin, and (iv) tracing psychoactive plants under forensic surveillance.

Froth flotation, a widely used mineral beneficiation technique, generates substantial volumes of data, offering the opportunity to extract valuable insights from these data for production line analysis. The quality of flotation data is critical to designing accurate prediction models and process optimisation. Unfortunately, industrial flotation data are often compromised by quality issues such as outliers that can produce misleading or erroneous analytical results. A general approach is to preprocess the data by replacing or imputing outliers with data values that have no connection with the real state of the process. However, this does not resolve the effect of outliers, especially those that deviate from normal trends. Outliers often occur across multiple variables and their values may occur in normal observation ranges, making their detection challenging. An unresolved challenge in outlier detection is how far is far enough for an observation to be considered an outlier. Existing methods rely on domain experts’ knowledge which is difficult to apply when experts encounter large volumes of data with complex relationships. In this paper, we propose an approach to conduct outlier analysis on a flotation dataset. The approach uses a 2σ rule as the threshold to find quasi-outliers and multiple machine learning (ML) algorithms including k-Nearest Neighbour (kNN), Local Outlier Factor (LOF), and Isolation Forest (ISF) to identify true outliers. The approach then analyses the mutual coverage between quasi-outliers and outliers from the ML algorithms to identify the most effective outlier detection algorithm. We found that the outliers by kNN cover outliers of other methods. We use the experimental results to show that outliers affect model prediction accuracy and excluding outliers from training data can reduce the average prediction errors.

Glutathione (GSH) and melatonin (MLT) are two antioxidants that have been described as having a protective role against oxidative stress in several animal species, improving sperm quality and survival after cryopreservation. Since there is no knowledge on the simultaneous use of these two substances concerning its effects on ram semen cryopreservation, this study aimed to evaluate the effects of MLT, GSH, or their association, on in vitro parameters of ram semen after thawing. During eight weekly sessions, the semen from three Merino rams was pooled, divided into four aliquots, and diluted with an egg yolk-based semen extender without (control) and with antioxidants (MLT 1mM, GSH 5mM, and MLT 1mM + GSH 5mM). Diluted semen was evaluated before and after freezing process. Supplementation of fresh semen with GSH at 5 mM had a deleterious effect on total motility progressive (TPM), curvilinear velocity (VCL), straight-line velocity (VSL), average-path velocity (VAP), linearity (LIN), straightness (STR) and increased slow spermatozoon (%). MLT at 1 mM also has a negative effect on TPM, VSL, and STR in fresh semen. In thawed semen, 1 mM of melatonin increased the TPM regarding the group control. Also, the combination of both antioxidants attenuates the negative effect of GSH 5mM on TPM, VSL and BCF. These results indicate that 5mM GSH impairs or does not improve sperm kinetic parameters in fresh semen and suggest that melatonin when combined with GSH plays a protective role on these effects.

Background: Given the extensive translation of the Prolapse Quality of Life Questionnaire (P-QoL) into many languages, it is imperative to develop an Arabic version to facilitate study on Pelvic organ health within the Arabian culture. Objective: To investigate, cross culturally adapt and validate Arabic version of the P-QoL. Study Design: Cross-cultural adaptation and psychometric testing. Methods: A total of 90 participants were included in the study. This cross-sectional study went through two phases; during phase I, the P-QoL was translated and adapted from English into Arabic. The Arabic version was psychometrically validated during phase II using the test-retest reliability internal consistency with Cronbach’s alpha coefficient, convergent construct validity (CC) among the four study tools using Spearman’s coefficient (r) and discriminative validity using Mann-Whitney test to find differences between the means of the two samples. Results: A satisfactory level of semantic, conceptual, idiomatic, and content comparability was reached in the cross-cultural adaptation of the Arabic version of the P-QoL questionnaire. The internal consistency was high in terms of psychometric validation, with a Cronbach’s alpha coefficient of 0.971 for the P-QoL questionnaire. The test-retest results showed a high reliability with interclass correlation coefficient (ICC) of P-QoL = 0.987. The convergent construct validity was highly accepted (moderately strong), reflecting a positive correlation between the Arabic version of the P-QoL and the Australian Pelvic Floor Dysfunction Questionnaire (APFD) r = 0.68 (p &lt; 0.001). Similarly, a significant convergent validity of P-QoL Arabic version and Visual Analogue Scale (VAS) r = 0.47 (p &lt; 0.001) was found, as well as the correlation between the APFD and the VAS r = 0.46 (p &lt; 0.001). However, there were no significant correlation between the SF-12, the P-QoL, the APFD, and the VAS. Conclusion: Based on a significant correlation between the Arabic APFD and the VAS, the results reveal good reliability, internal consistency, and construct validity. It is recommended that Arabic-speaking females with pelvic organ prolapse use the Arabic version of the P-QoL. More research is needed to assess the responsiveness of the P-QoL.

Ukraine is an associate member of the European Union and in the coming years it is expected that all the data and services already used by European Union countries will become available for Ukraine. An important program, which is the basis for building European monitoring services for Smart Cities, is the Copernicus program. The two most important services of this program are Copernicus Land Monitoring Service (CLMS) and Copernicus Atmosphere Monitoring Service (CAMS). CLMS provides important information on Land Use in Europe. In the context of Smart Cities, the most valuable one is the Urban Atlas service, which is related to local CLMS services and provides a detailed digital city plan in vector form, which is segmented into small functional areas classified by the CORIN nomenclature. The Urban Atlas is a geospatial layer with high-resolution, which is built for all European cities with a population of more than 100,000 that combines high-resolution sat-ellite data, city segmentation by blocks and functional areas, important city infrastructure, etc. This product is used as a basis for city planning and obtaining analytics on the most important indicators of city development including air quality monitoring. For Ukraine, such geospatial products are not provided under the Copernicus program. It is important to start work on its development and implementation as early as possible, so that when the first city atlas appears, Ukraine will be ready to work with it together with the European community. This requires preparing the basis for na-tional research and training national stakeholders and users to use this product. To make this happen it’s necessary to have national geospatial product, which can be used as an analogue of the city atlas. In this article authors analyzed the existing methods of air quality assessment and assessment of the SDG indicator 11.6.2 achieving for European cities, based on which the indicator 11.6.2 for Ukraine for 5 years was evaluated for the first time. The obtained results are analyzed and the values of indicator 11.6.2 for Ukraine are compared with European countries.

Despite much published literature on the impacts of agriculture on water quality, knowledge gaps persist regarding which farming systems are of most concern for these relationships, which could help water resource planners better target water management efforts. This study addresses these subjects, seeking to understand how this relationship varies across different farming systems. We used data on water quality status in watersheds of an agricultural region in southern Portugal and crossed it with a map of farming systems for the same region provided by a previous study. By overlaying both data layers, we characterized the areal shares of the farming systems in the watersheds and inspected how these shares relate with water quality status through logistic regression. Results support that the impact of agriculture on water quality is mostly related with specific farming systems. We believe this type of information can be of high interest for agricultural planners and policymakers interested in meeting water quality standards, and we conclude by suggesting innovative policy options based on payments to farmers operating selected farming systems, as a cost-effective way to reconcile agricultural and environmental policy objectives.

Embryo quality evaluation during in vitro development is vital for the success of assisted reproductive technologies (ART). However, the subjective morphological assessment by embryologists may result in inconsistencies that affect the selection of the best embryo for transfer. To provide a more comprehensive evaluation of embryo quality, we performed the integration of embryo metabolomics with standardized morphokinetic classification. The culture medium of 55 embryos (from 21 couples undergoing ICSI) was collected at two timepoints (day 3 and 5). Samples were split into Good (n=29), Lagging (n=19) and Bad (n=10) according to embryo morphokinetic evaluation. Embryo metabolic performance was assessed by 1H-NMR, monitoring the variation of specific metabolites (pyruvate, lactate, alanine, glutamine, acetate, formate). Adjusted metabolite differentials were observed during the first three days of culture and found to be discriminative of embryo quality at the end of day 5. Pyruvate, alanine, glutamine, and acetate were major contributors to this discrimination. Good and Lagging embryos were found to export and accumulate pyruvate and glutamine in the 3 first days of culture, while Bad embryos consumed them. This suggests that Bad embryos have a less active metabolism than Good and Lagging embryos and these two metabolites as putative biomarkers for embryo quality. This study provides a more comprehensive evaluation of embryo quality and can lead to improvements in ART by enabling the selection of the best embryos. By combining morphological assessment and metabolomics, the selection of high-quality embryos with the potential to result in successful pregnancies may become more accurate and consistent.

Background: Fungi are ubiquitous microorganisms that are easily dispersed through the air. In healthcare environments, indoor air can favor the spread of healthcare-associated fungal infections, compromising mainly immunocompromised hospitalized individuals. Thus, this study aimed to evaluate the indoor air contamination in healthcare environments, investigating mainly the presence of potentially pathogenic yeasts. Methods: Indoor air samples were collected from twelve healthcare environments (hospital and medical clinics). After the growth, isolation, and purification of the yeast colonies, the isolates were identified by polymerase chain reaction using species-specific primers for yeasts of the genus Candida and sequencing of D1/D2 domains of the large ribosomal subunit (LSU rRNA). Results: Fourteen yeast species were identified, including emerging pathogens. Species of clinical importance such as Candida parapsilosis, Candida orthopsilosis, Candida glabrata, Rhodotorula mucilaginosa, and Trichosporon mucoides were present. C. Parapsilosis was the most prevalent species, followed by Rodothorula mucilaginosa. Conclusions: The present study shows that potentially fungal pathogens were present in air samples from healthcare environments, proving the role of indoor air in spreading infections. Thus, monitoring air quality in healthcare environments is a fundamental approach in developing infection control measures, especially those related to invasive fungal infections.

The present study investigates the relationship between the transmission of COVID-19 infections and climate indicators in Dhaka City, Bangladesh, using coronavirus infections data available from the Institute of Epidemiology, Disease Control and Research (IEDCR), Bangladesh. The Spearman-ranked correlation test was carried out to study the association of seven climate indicators, including humidity, air quality, minimum temperature, precipitation, maximum temperature, mean temperature and wind speed with the COVID-19 outbreak in Dhaka City, Bangladesh. The study found that, among the seven indicators, only three indicators (air quality, minimum temperature and average temperature) have a significant relationship with new COVID-19 cases. The results of this paper will give health regulators and policymakers valuable information to lessen the COVID-19 infection in Dhaka and other countries around the world.

In Wikipedia, articles about various topics can be created and edited independently in each language version. Therefore, quality of information about the same topic depends on language. Any interested user can improve an article and that improvement may depend on popularity of the article. The goal of this study is to show what topics are best represented in different language versions of Wikipedia using results of quality assessment for over 39 million articles in 55 languages. In this paper, we also analyze how popular are selected topics among readers and authors in various languages. We used two approaches to assign articles to various topics. First, we selected 27 main multilingual categories and analyzed all their connections with sub-categories based on information extracted from over 10 million categories in 55 language versions. To classify the articles to one of the 27 main categories we took into account over 400 million links from articles to over 10 million categories and over 26 million links between categories. In the second approach we used data from DBpedia and Wikidata. We also showed how the results of the study can be used to build local and global rankings of the Wikipedia content.

The study's objective was to investigate changes in the fatty acid composition of cow milk in general and in 80 Romanian Spotted cows' husbandry and feeding systems in particular (grazing – GC group vs. stabulation – SC group). The ultimate objective was to determine if the changes that happened in the milk also transferred to the finished product. Also, the influence of the raw milk quality produced by both systems was evaluated when yogurt was made from it. The milk was gathered in May, July, and September and used for both the yogurt-making process and the study, which lasted from May to October. As comparison to milk from SC, milk from grazed caws had larger percentages of fat and dry matter throughout the summer (GC) season. Moreover, pasture-based rations (MGC) contained more PUFA than MCS did. Data research revealed that not only do factors like milk origin and initial quality have a substantial impact on yogurt quality parameters, but also technologies like milk fermentation have a considerable impact on the fatty acid profile of yogurt. As comparison to cows kept permanently in stables, grazed cows (MGC) had fat with a lower concentration of saturated fatty acids and a higher proportion of rumenic, vaccenic, and oleic acids (MSC). When fresh milk is processed into yogurt and other dairy products, the fatty acid profiles alter, with saturated fatty acids predominating over unsaturated ones. The findings show that pasture-fed cows have a positive impact on milk quality, particularly in terms of fatty acid profile, as well as on yogurt's ultimate nutritional and dietary quality.

Celiac disease (CD) is an autoimmune disorder triggered by the ingestion of gluten and affects approximately 1% of the global population. Currently, the only treatment available is lifelong strict adherence to a gluten-free diet (GFD). Chronic diseases such as CD affect patients and their family members’ quality of life (QoL); particularly parents and caregivers who play an essential role in the child’s care and treatment. A higher level of psychological distress has been found in the parents of children with chronic ailments due to limited control over the child’s daily activities and the child’s illness. In this context, the validation of a specific questionnaire of QoL is a valuable tool to evaluate the difficulties faced by parents or caregivers of children with this chronic illness. A specific questionnaire for this population can elucidate the reasons for stress in their daily lives as well as the physical, mental, emotional, and social impact caused by CD. Therefore, this study aimed to develop and validate a specific questionnaire to evaluate the QoL of parents and caregivers of children and adolescents with CD. The study was developed in six steps: (i) development of the CD parent/caregiver QoL questionnaire (CDPC-QoL); (ii) subjective evaluation; (iii) validation of the questionnaire by the Delphi method; (iv) evaluation of the internal consistency and reproducibility of the CDPC-QoL; (v) application of the questionnaire to Brazilian CD parents or caregivers; and (vi) statistical analysis. Overall results showed that a higher family income resulted in a higher score of the worries domain. In addition, having another illness besides CD decreased the QoL (except in the worries domain). The other variables studied did not present a statistically significant impact on the QoL, which was shown to be low in all aspects. Knowledge of the QoL is important to help implement effective strategies to improve celiac patients’ quality of life and reduce their physical, emotional, and social burden.

Background: Alarming data indicates that low back pain (LBP) affected around 619 million people globally in 2020, that presenting significant health and economic burden. Importantly, the chronic LBP (cLBP) strongly impairs quality of life and leads to disability and premature retirement thus emphasizing the urgent need for providing deeper insight into the factors that affect treatment outcomes and offer thorough guidance for the assessment and management of this disease. Taking into consideration the rising prevalence of cLBP and knowledge gap referring to the overall health benefits of balneotherapy (BT), the aim of this study was to assess the effects of BT on functional status, quality of life and psychological symptoms in patients with cLBP. Methods: A total 210 patients were recruited and divided into two groups: patients receiving conventional pharmacological therapy (CT) and receiving BT. The effectiveness of the treatment was assessed on the basis of Visual Analog Scale for pain intensity, EuroQol (EQ-5D) for the patient’s self-rated health and Work Ability Index Questionnaire to evaluate functional ability. In order to provide deeper insight into the quality of life and also factors associated with the functional status and mental health affected by BT, we also used the Short Form Health Survey Questionnaire and Center of Epidemiologic Studies Depression Scale. Results: Our findings suggest that BT significantly contributed to reduction of pain, better functionality and disability perception status. Conclusions: Understanding the association between individual perceptions of functionality, emotional and social elements provides basis for providing comprehensive guidelines and recommendations for cLBP management.

The dynamic global automotive sector is characterized by an ever-evolving demand for high-quality vehicles and accessible prices. This research tackles the issue of scrap reduction in electric motor manufacturing for the automotive industry, specifically in a Chinese company, by employing the PDCA methodology. The paper delves into the company's background and current landscape, while pinpointing the problem: specific production lines segments experiencing hi-pot issues are the primary source of scrap. The overarching goal is to design and implement a strategy that, leveraging the PDCA approach, reduces scrap generated during the eight-months subassembly (armature) manufacturing process, from its current average of 2.92% to 0.7%, ultimately enabling the company to eliminate hi-pot defects.

The purpose of this study was to identify subgroups of quality of life (QOL) changes in breast cancer survivors (BCS) and to determine factors associated with subgroups of consistently low or deteriorated QOL. We enrolled 101 women recently diagnosed with breast cancer in South Korea and asked them to complete a questionnaire at baseline (within 1 month of diagnosis), 1 year later (Year 1), 2 years later (Year 2), and 3 years later (Year 3). We assessed QOL using the global QOL subscale from the EORTC QLQ-C30. We defined low QOL as a global QOL score 10 points below the mean score of the general population. Based on low QOL as defined in this study, we identified subgroups of QOL changes over 3 years. We identified four subgroups of QOL changes: improved (47.4%), stable (30%), continuously low (8.8%), and deteriorated (13.8%) and considered the last two categories (22.6%) as poor QOL. Logistic regression analyses demonstrated that significant determinants of poor QOL were insomnia at Year 1, fatigue and anxiety at Year 2, and fatigue, depression, and comorbidity at Year 3. In conclusion, persistent symptoms of insomnia, fatigue, anxiety, depression, and comorbidity are potential risk factors for poor QOL in BCS.

Suboptimal micronutrient intake in children remains a public health concern around the world. This study examined the relationship between a previously defined dietary carbohydrate quality index (CQI) and the risk of micronutrient intake inadequacy in a pediatric cohort of Spanish preschoolers. Children aged 4-5 years old were recruited at their medical center or at school, and information on sociodemographic, dietary, and life-style variables were collected through a self-administered online questionnaire. Dietary information was obtained from a validated 147-item semi-quantitative food frequency questionnaire. We calculated the CQI and categorized participants in quartiles according to their score. We assessed the intakes of 20 micronutrients and evaluated the probability of intake inadequacy using the Estimated Average Requirement cut-off point. Generalized estimating equations were used to adjust for potential confounders and account for the intra-cluster correlations between siblings. The adjusted proportions of children with inadequate intake of ≥3 micronutrients were 23%, 12%, 11% and 9% in the first, second, third and fourth quartiles of the CQI, respectively. Children in the highest quartile of CQI had 0.22-fold lower odds (95%CI 0.10-0.48) of having ≥3 inadequate micronutrient intakes than their peers in the lowest quartile. These findings reinforce the relevance of carbohydrate quality in children’s diets.

Chronic pain is a source of major alterations in quality of life. It represents significant costs for health systems, and reduces the competitiveness of the working population. Vulnerability can drive the incidence of chronic pain, through its influence on modifiable risk factors, and reduced utilization of health care systems. But vulnerability can also be the consequence of a chronic pain: illness can push people into precariousness. We analysed the factors associated with pain intensity among vulnerable persons with a chronic condition, in five European countries (N=1,364). Pain was, among the whole set of variables, the main predictor of sleep problems, fatigue, depression, self-perceived health, physical and mental quality of life. This is in line with other studies showing the major impact of pain on an individual’s health and life. Multivariable analyses, adjusting for the whole set of variables, showed that women had more intense pain, as well as participants with a lower education level. These results confirm the social component in the complex etiology of pain and clearly plaid in favor of integrated care, taking into account individual characteristics and environment.

The CARA program has been developed since 2008 by the French reference laboratory for air quality monitoring (LCSQA) and the regional monitoring networks to gain a better knowledge at the national level on the particulate matter (PM) chemistry and its diverse origins in urban environments. It results of strong collaborations with international-level academic partners, allowing to bring state-of-the-art, straightforward and robust results and methodologies within operational air quality stakeholders (and subsequently, decision makers). Here, we illustrate some of the main outputs obtained over the last decade thanks to this program, regarding methodological aspects (both in terms of measurement techniques and data treatment procedures) as well as acquired knowledge on the predominant PM sources. Offline and online methods are used following well-suited quality assurance and quality control procedures, notably including inter-laboratory comparison exercises. Source apportionment studies are conducted using various receptor modeling approaches. Overall, the results presented herewith underline the major influences of residential wood burning (during the cold period) and road transport emissions (exhaust and non-exhaust ones, all along the year), as well as substantial contributions of mineral dust and primary biogenic particles (mostly during the warm period). Long-range transport phenomena, e.g., advection of secondary inorganic aerosols from the European continental sector and of Saharan dust into the French West Indies, are also discussed in this paper. Finally, we briefly address the use of stable isotope measurements (δ15N) and of various organic molecular markers for a better understanding of the origins of ammonium and of the different organic aerosol fractions, respectively.

The consumption of dairy products and the dairy industry is one of the main global agro-food sectors for size, economic importance and level of technology. Microbiological quality of pasteurized milk or other milk products is dependent on microbiological quality of raw milk. A variety of microbiological count methods is available for monitoring the hygienic quality of raw milk. Among them, the pour plate method is the official essay for counting the number of colony forming units in milk samples according to ISO 4833-1:2013. The aim of the present study is the validation of the Micro Biological Survey (MBS) method, against the reference plate count method, for the assessment of the microbiological quality of raw milk. This comparative study, performed in collaboration with the “Istituto Zooprofilattico Sperimentale del Lazio e della Toscana M. Aleandri” (IZSLT), demonstrates the accuracy of this alternative method for the determination of total viable bacterial count in cow’s raw milk. The results obtained with the MBS method highlighting its potential as a valid tool for reliable microbiological analysis in dairy industries.

Rural areas are not only faced with the problems of rural depopulation but also with the problem of water supply and water quality which is a basic necessity of life. In light of this, this paper assesses the rural water supply situation and the bacteriological quality of different water sources in the Obokun Local Government Area of Osun State, Nigeria. The safety of the water sources for human consumption and possible occurrence of the water borne diseases in the study area were determined. The study employed descriptive and analytical methods of data analysis to achieve the objectives of the inquiry. Findings showed that the study area suffered from inadequate water supply and poor locations of the sources of water: The study also revealed that the microbiological quality of the water sources used was unsafe, poor and not acceptable for human consumption. In addition, many man- days-hours were wasted in search of water. It is therefore recommended that the government should make the rural water supply and the maintenance of water quality a priority in its policy formulation.

Background: Computed tomography examinations have produced high radiation doses to patients, especially the CT brain. This study aimed to optimize the radiation dose and image quality in adult CT brain protocol. Materials and Methods: Images were acquired by Catphan 700 phantom. Radiation doses were recorded as CTDIvol and dose length product (DLP). CT brain protocols were optimized by varying parameters such as kVp, mAs, signal-to-noise ratio (SNR) level, and Clearview iterative reconstruction (IR). Image quality were also evaluataion by The AutoQA Plus software. Results: CT Number accuracy and linearity had a robust positive correlation with the linear attenuation coefficient (µ) and showed more inaccurate CT numbers when using 80 kVp. MTF showed a higher value in 100 and 120 kVp protocols, while high contrast spatial resolution showed a higher value in 80 and 100 kVp protocols. Low contrast detectability and CNR tended to increase when using high mAs, SNR and Clearview IR protocol. Noise decreased when using a high radiation dose and a high percentage of Clearview IR. CTDIvol and DLP were increased with increasing kVp, mAs, and SNR levels, while the increasing percentage of Clearview did not affect the radiation dose. Conclusion: Optimized protocols, including radiation dose and image quality, should be evaluated to preserve diagnostic capability. The recommended parameter settings include kVp set between 100-120 kVp, mAs ranging from 200-300 mAs, SNR level within the range of 0.7-1.0, and an iterative reconstruction value of 30% Clearview to 60% or higher.

Over 3.0 billion people of the 7.75 billion globally suffer from malnutrition due to deficiencies in micronutrients, particularly iron, zinc, and vitamins (such as vitamin A, B complex, E, and folate, etc.). In response, there is growing consumer interest in foods that provide traditional nutrients and contain additional compounds beneficial to health and well-being. Wheat is the most important cereal crop in terms of both production and consumption, contributing about 30% of total cereal consumption worldwide. It provides a significant source of carbohydrates and gluten protein (around 12-14% protein), which supply substantial energy. Wheat grain is also rich in various nutrients, such as macro-elements like phosphorus (P), potassium (K), calcium (Ca), and magnesium (Mg); microelements like iron (Fe), zinc (Zn), manganese (Mn), and vitamins B complex: thiamin (B1), riboflavin (B2), niacin (B3), pantothenic acid (B5), pyridoxine (B6), biotin (B7), folate (B9), additionally soluble fiber and other trace minerals which are higher than in other major cereals. The inner bran coats, phosphates, and other mineral salts in wheat contribute to its beneficial effects on bowel movements. Despite its nutritional benefits, the quality of wheat's nutrients is a topic of ongoing discussion. Exploring ways to enhance the nutritional quality of wheat could provide valuable insights for scientists working to improve global nutrition status.

This scientific paper explores the increasingly widespread use of collaborative robots in the industrial environment, highlighting them as a solution to challenges related to the high costs of human labour and the associated management difficulties. The authors focus on the process of defining requirements for the implementation of collaborative robots, providing strategies based on mathematical management models. This approach translates into significant benefits for companies, such as cost reduction, quality improvement, and increased operational efficiency. Additionally, the paper proposes an innovative mathematical model for assessing total costs, budgeting, profitability, and electric power consumption associated with the operation of collaborative robots. This model allows for a comparison between the costs involved in using human labour and those associated with collaborative robots, providing critical information for technological investment decisions. The efficiency of this mathematical model is demonstrated through a practical application, where collaborative robots were integrated into a production environment, and costs and efficiency were evaluated compared to the use of human labour. This scientific paper provides a systematic and efficient approach to implementing collaborative robots in industrial processes, benefiting from strategies based on mathematical management models and an original mathematical model for evaluating performance and associated costs.

Recent technological advancements such as IoT and Big Data have granted industries extensive access to data, opening up new opportunities for integrating Artificial Intelligence (AI) across various applications to enhance production processes. We can cite two critical areas where AI can play a key role in industry such as product quality control and predictive maintenance. This paper presents a survey of AI applications in the domain of Industry 4.0, with a specific focus on product quality control and predictive maintenance. Experiments were conducted using two datasets, incorporating different machine learning and deep learning models from the literature. Furthermore, this paper provides an overview of the AI solution development approach for product quality control and predictive maintenance. This approach includes several key steps, such as data collection, data analysis, model development, model explanation, and model deployment.

Sleep is a fundamental human need: sleep disruption, in fact, causes an increase in the activity of the sympathetic nervous system and the hypothalamic-pituitary-adrenal axis, metabolic effects, changes in circadian rhythms and pro-inflammatory responses. Sci-entific literature is finally starting to pay attention to the central role of sleep-wake rhythm alterations for patients health. Oxaliplatin is used extensively for the treatment of gastrointestinal cancer and other malignancies, with increased frequency of use in recent years. This study aims to understand the effects of sleep-wake rhythm alterations on health and quality of life on cancer patients treated with oxaliplatin. Study has been conducted through the creation and distribution of questionnaires to patients to inves-tigate the potential alteration of the sleep-wake quality. Evaluating the influence of the collected variables on sleep quality, only liver and biliary tract and pancreas tumor lo-calization, in males, and previous difficulty sleeping, and anxiety, worries and stress, in females, resulted statistically significant. The results obtained may serve as foundation for designing awareness campaigns and updating of patients, healthcare personnel and caregivers, to improve health and quality of patients life.

Since the integration of electronic devices and intelligent electronic devices into the power grid, power quality (PQ) has consistently remained a significant concern for system operators and experts. Maintaining high standards of power quality is crucial to prevent malfunctions and faults in electric assets and in connected loads. Recently, PQ studies have shifted their focus to a specific frequency range, previously not considered problematic, the supraharmonic 2kHz–150kHz range. This range is not populated by the harmonic components of the 50-60 Hz mains fundamental, but a combination of intentional emissions, switching and non-linearity by-products and various types of resonances. This paper aims to provide a detailed analysis of the impact of SH on power network operation and assets, focusing on the most relevant documented negative effects, namely power loss and heating of grid elements, aging of dielectric materials, failure of medium voltage (MV) cable terminations, and interference to equipment and to power line communication (PLC) technology in particular. Under some shareable assumptions limits are derived and compared to existing ones for harmonic phenomena, providing a clear identification of the primary issues associated with supraharmonics and suggestions for the standardization process. Strictly related is the problem of grid monitoring and assessment of SH distortion, discussing the suitability of normative requirements for instrument transformers (ITs) with specific focus on their accuracy.

The intrinsic non-linearity and complexity of suspended sediment dynamics, which are impacted by the geographical variability of basin parameters and temporal climatic patterns, make it difficult to estimate suspended sediment concentration (SSC) accurately in hydrological processes. Deep neural networks (DNNs), a cutting-edge modeling method that can capture the innate non-linearity in hydrological systems, have emerged as a solution to this problem. Using primary data on discharge, SSC, and turbidity, the long short-term memory method of DNNs was employed in this study to simulate the discharge-suspended sediment connection for the Esopus Creek, NY, USA as the first objective. To develop effective modeling strategies, multiple scenarios of feature selection, including combinations of discharge, turbidity and SSC for preceding days, were considered. Secondly, the variations in SSC and discharge between the three USGS gages along Esopus Creek that were upper stream, lower stream, and downstream, adjacent to the pourpoint were analyzed. Statistical metrics and scenarios of feature importance were used to evaluate the effectiveness of the DNN-based models. The study shows that among 24 DNN approaches feature selection is crucial in simulating the daily SSC, and discharge and presenting novel research directions for utilizing machine learning algorithms in water quality.

The Florida Keys, a delicate archipelago of sub-tropical islands extending from the south-eastern tip of Florida, host the vast majority of the only coral barrier reef in the continental United States. Abiotic as well as microbial components of the surrounding waters are pivotal for the health of reef habitats, and thus could play an important role in understanding the development and transmission of coral diseases in Florida. In this study, we analyzed microbial community structure and abiotic factors in waters around the Florida Reef Tract. Both, bacterial and eukaryotic community structure were significantly linked with variations in temperature, dissolved oxygen and total organic carbon values. High abundances of copiotrophic bacteria as well as several potentially harmful microbes, including coral pathogens, fish parasites and taxa that have been previously associated with Red Tide and shellfish poisoning were present in our datasets and may have a pivotal impact on reef health in this ecosystem.

Background: The aim of the present work is the elaboration of a systematic review of existing research on physical fitness, self-efficacy for physical exercise, and quality of life in adulthood. Method: Using the PRISMA statement guidelines, and based on the findings in 396 articles, the final sample was composed of 31 articles, which were reviewed to show whether self-efficacy has previously been studied as a mediator in the relationship between physical fitness and quality of life in adulthood. Results: The results indicate that little research exists in relation to healthy, populations with the majority being people with pathology. Physical fitness should be considered as a fundamental aspect in determining the functional capacity of the person. Conclusions: We discuss the need to investigate the mediation of self-efficacy in relation to the value of physical activity on quality of life and well-being in the healthy adult population in adult life.

Filter Media (FM) sourced from recycled organic and mineral material offers a low cost and effective means of treating urban stormwater. Using recycled materials rather than from an increasingly scarce source of virgin materials (typically sandy loam soil) can ensure a sustainable long-term economy and environment. This paper presents results from the laboratory analysis and mathematical modeling to highlight the performance of recycled organic and mineral material in removing nutrients and metals from stormwater. Analysis included physical and chemical characterisation such as particle size distribution, saturated hydraulic conductivity (Ksat), bulk density, effective cation exchange capacity, and pollutant removal performance. Design mixes (DM), comprising a combination of organic and mineral materials, were characterised and used to develop/derive modelling design within the Model for Urban Stormwater Improvement Conceptualisation (MUSIC v6) [1]. Comparison is made to the Adoption Guidelines for Stormwater Biofiltration Systems - Summary Report [2] which were based on the Facility for Advancing Water Biofiltration (FAWB) guidelines to assist in the development of biofiltration systems, including the planning, design, construction and operation of those systems. An observed outcome from over two decades of biofiltration guideline development has been the exclusion of alternative biofilter materials due to claims of excessive leaching. Results from this study indicate that high nutrient and metal removal rates can be achieved over a range of hydraulic conductivities using design mixes of recycled organic and mineral materials that have a demonstrated equivalence to existing guideline specifications.

We aimed at analyzing Chlorophyll-a and CDOM dynamics from field measurements and at assessing the potential of multispectral satellite data for retrieving water-quality parameters in three small surface reservoirs in the Brazilian semiarid region. More specifically, this work comprises i) analysis of Chl-a and trophic dynamics; ii) characterization of CDOM; iii) estimation of Chl-a and CDOM from OLI/Landsat-8 and RapidEye imagery. The monitoring lasted 20 months within a multi-year drought, which contributed to water-quality deterioration. Chl-a and trophic state analysis showed a highly eutrophic status for the perennial reservoir during the entire study period, while the non-perennial reservoirs ranged from oligotrophic to eutrophic, with changes associated with the first events of the rainy season. CDOM characterization suggests that the perennial reservoir is mostly influenced by autochthonous sources, while allochthonous sources dominate the non-perennial ones. Spectral-group classification assigned the perennial as CDOM-moderate and highly eutrophic reservoir, whereas the non-perennial ones were assigned as CDOM-rich and oligotrophic-dystrophic reservoirs. The remote sensing initiative was partially successful: the Chl-a was best modelled using RapidEye for the perennial; whereas CDOM performed best with Landsat-8 for non-perennial reservoirs. This investigation showed high potential for retrieving water quality parameters in dry areas with small reservoirs.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

The purpose of the study is to empirically analyze the effect of quality of governance on tax revenue in South Africa. This is done by analyzing a time series dataset covering 1996 to 2020. The study used voice and accountability, regulatory quality, government effectiveness, control of corruption, political stability and rule of law as proxies of quality of governance. Multiple regression analysis was performed to test hypotheses. Based on the regression results, all quality of governance variables in South Africa have a negative effect on tax revenue except corruption control. The findings of this study also include policy recommendations. The government of South Africa must design and implement effective ways to combat poor governance, which results in a tax revenue shortfall.

Background: Gluten neuropathy (GN) is defined as an otherwise idiopathic peripheral neuropathy in the presence of serological evidence of gluten sensitivity (positive antigliadin and/or transglutaminase or endomysium antibodies). We aimed to compare the quality of life (QoL) of GN patients with control subjects and to investigate the effect of a gluten free diet (GFD) on the QoL. Methods: All consecutive patients with GN attending a specialist neuropathy clinic were invited to participate. Overall Neuropathy Limitations Scale (ONLS) was used to assess the severity of neuropathy. The SF-36 questionnaire was used to measure participants’ QoL. A strict GFD was defined as effectively been able to eliminate all circulating gluten sensitivity-related antibodies whilst on the diet. Results: Fifty-three patients with GN and 53 age and gender matched controls were recruited. Compared to controls, GN showed significantly worse scores in physical functioning, role limitations due to physical health, energy/fatigue and general health subdomains of SF-36. After having adjusted for age, gender and disease severity, being on a strict GFD correlated with better SF-36 scores on the pain domain of the SF-36 (beta 0.317, p=0.019) and the overall health change domain of the SF-36 (beta 0.306, p=0.017). Conclusion: In GN physical dysfunctioning is the major determinant of poor QoL compared to controls. Routine checking for elimination of gluten sensitivity-related antibodies that results from a strict GFD should be encouraged as such elimination ameliorates the overall pain and health scores, indicating better QoL.

Wikipedia is the most popular and the largest user-generated source of knowledge on the Web. Quality of the information in this encyclopedia is often questioned. Therefore, Wikipedians have developed an award system for high quality articles, which follows the specific style guidelines. Nevertheless, more than 1.2 million articles in Polish Wikipedia are unassessed. This paper considers over 100 linguistic features to determine the quality of Wikipedia articles in Polish language. We evaluate our models on 500,000 articles of Polish Wikipedia. Additionally, we discuss the importance of linguistic features for quality prediction.

Artificial Intelligence (AI) is fundamentally reshaping various industries by enhancing decision-making processes, optimizing operations, and unlocking new opportunities for innovation. This paper explores the applications of AI across four key sectors: healthcare, finance, manufacturing, and retail. Each section delves into the specific challenges faced by these industries, the AI technologies employed to address them, and the measurable impact on business outcomes and societal welfare. We also discuss the implications of AI integration, including ethical considerations, the future trajectory of AI development, and its potential to drive economic growth while posing challenges that need to be managed responsibly.

Serine is widely involved in antioxidant synthesis, immune response, and fat metabolism. However, it remains unclear whether dietary serine supplementation affects fat deposition in the skeletal muscles of pigs. Thus, we explored the effects of dietary serine supplementation on growth performance, meat quality, and composition of gut microbes and their metabolites in growing-finishing pigs. Forty-eight boars weighing approximately 20 kg were fed either a basal diet or a basal diet supplemented with 0.15% serine. The results showed that dietary serine increased the daily weight gain and improved the antioxidant ability of pigs, as indicated by the decreased malondialdehyde content and increased glutathione and superoxide dismutase content. Pigs supplemented with serine had better meat quality, as shown by the lower drip loss and higher IMF content. Furthermore, dietary serine increased the relative abundance of Streptococcus and Lactobacillus and decreased the relative abundance of Clostridium_sensu_stricto_1 and Terrisporobacter. Differential microbial metabolites were mostly enriched in metabolic pathways related to lipid synthesis, such as alpha-linolenic acid metabolism and steroid hormone biosynthesis. Correlation analysis showed that the altered metabolites were closely related to the intestinal microbiota. In conclusion, our results suggested that serine serves as a potential additive for improving meat quality in growing-finishing pigs.

The lengthy maturation period is the key cause of the reduced hot pepper market value. An experiment was performed to assess the effects of R/B/W light qualities on reducing the maturation period. The maturation period was shortened by 16 days under 4R:1B:5W compared to the control. The appearance of the first flower is a limiting factor affecting the maturation period. It exhibited a dark purple color and an abnormal petal under 4R:1B:5W compared to the control, which was associated with increased contents of flavonoids, total organic acids, and phenolics and decreased total amino acid and carbohydrate contents. Plant hormone, flavonoid, ABC transporters, key metabolites (such as amino acid, carbohydrate, organic acid) was associated with first flower development. Ethylene response factors (ERFs) mediated by light, especially ERF021, were identified as potential hub regulators during the development of the first flower due to their involvement in all the associated metabolic pathways.

This study presents a comprehensive assessment of indoor particulate matter (PM) concentrations, focusing on PM1, PM2.5, and PM10 in five Primary Health Centers (PHCs): Arakale, Federal College of Agriculture (FECA), Iju, Oba-Ile, and Owode within Akure Local Government Areas in Nigeria. The primary novelty of this research lies in its detailed exploration of the toxicity potential of these PM fractions, providing valuable insights into the local air quality and associated health risks. The study assesses the health implications by calculating the toxicity potential (TP), Relative Risk (RR), Excess Risk (ER), and Attributable Fractions (AF) for cardiopulmonary and lung cancer mortality. The results reveal varying RR values for all-cause mortality, with Arakale showing a slight elevation (RR: 1.061), indicating potential health risks. ER values for cardiopulmonary mortality range from 14.728±7.25 to 19.04±0.38, emphasizing the substantial excess risk associated with long-term PM2.5 exposure. The study also uncovers AF for cardiopulmonary mortality ranging between 11.03±0.31 to 19.22±0.04, underscoring the significant contribution of PM to cardiovascular and respiratory health risks. Similarly, AF for lung cancer mortality ranges from 10.03±0.012 to 17.13±0.10, highlighting the substantial association between PM2.5 exposure and lung cancer risk. These findings underscore the urgent need for targeted air quality management strategies and public health interventions in the studied locations to mitigate the heightened health risks associated with particulate matter pollution. The calculated RR, ER, and AF values offer crucial insights into the complex relationship between PM exposure and adverse health outcomes, providing a foundation for informed decision-making and future research endeavors.

Lack of water and salinity are common problems in many parts of the world. Therefore, some types of cacti can represent as promising crops. Therefore, the ability of cactus species to survive and adapt under natural stress conditions should be evaluated. In this study, it was aimed to evaluate the effect of salt stress on germination and emergence of pitaya seeds obtained from different fruit flesh colors, priming with plant growth regulators, namely salicylic acid (SA), oxalic acid (OA) and mepiquat chloride (MC). The experiment had a completely randomized design with a 2×4×3 factorial scheme corresponding to two pitaya cultivars (white and red fleshed), four NaCl concentrations (0, 2500, 5000 and 10000 ppm), and three PGRs (150 ppm/MC, SA, OC). The following variables were analyzed; germination percentage, mean germination time (MGT), germination stress tolerance ındex (GSTI), shoot length, seedling fresh weight and seedling dry weight ratio. According to the results, it was determined that the growing environment of the seed was important in salt stress resistance, while seeds matured in the environment with red fruit flesh were more tolerant to salt stress than white. Although Pitaya species are relatively salt tolerant, growth (about 30%) was significantly reduced above 2500 ppm and germination (about 45%) above 5000 ppm. MC was found promising as a priming agent in seeds obtained from fruits with white fruit flesh, and OA was found promising as a priming agent in seeds obtained from fruits with red fruit flesh in reducing NaCl-induced stress. Germination percentage stood out as the most important trait determining seed quality and was found to have positive effects on germination stress tolerance index (r: 0.63), seedling length (r: 0.74) and fresh seedling weight (r: 0.56). It is thought that the results obtained may contribute to pitaya cultivation and breeding.

Frontal incomes play an important role in human behavioral regulation and can be a determinant of eating behavior. The aim of this study was to analyse the frontal incomes in obese patients with and without Binge Eating Disorder (BED), compared to normoweight (NW) subjects and to analyse the effect of sex and binge disorder on quality of life, with age and BMI as covariates. A total of 114 participants comprised three different groups (obese with BED, obese without BED and NW) completed the Frontal Assessment Battery (FAB) and Impact of Weight on Quality of Life (IWQOL-lite). The results showed that obese patients, with and without BED, have poorer frontal functioning than NW persons. Obese patients with BED have lower performance in frontal income than obese patients without BED. Male participants have a higher perception of quality of life in all dimensions, with women showing lower values in self-esteem and sex life. Obese with BED show greater weaknesses in physical function. These results suggest that low frontal incomes and worse quality of life characterize obese patients, more evident in obese patients with BED.

Oceans cover about 70% of the Earth's surface, and about 95% remain unexplored for various reasons. Underwater wireless communication has been revolutionised with the help of Internet of Things networks. Recently, applications such as collecting marine data, marine monitoring, disaster prevention, historical exploration, oil and gas exploration, shipwreck exploration, maritime security, and monitoring of aquatic species and water pollution, and several applications have become possible. However, the problem of routing, information transfer, and resource preservation in the fluid underwater environment remains unsolved. In this research, we were looking for a solution to make routing more efficient, considering the various and practical criteria for the quality of service of the underwater IoT network. One of the outstanding features of this research is the possibility of dynamically weighing the parameters involved in routing and taking optimal and distributed decisions between network components. The proposed method has achieved acceptable results in terms of quality of service compared to recent methods.

Groundwater use for domestic and agricultural purposes is every day in rural communities. However, groundwater quality in those communities is still being determined due to the lack of water quality monitoring programs. The purpose of this study was to evaluate groundwater quality in rural communities using physiochemical parameters. Eight communities using communal boreholes were selected. Water samples were analysed for temperature, pH, electrical conductivity, total dissolved solids (TDS), ammonia, nitrate, and nitrite as Nitrogen. The pH means ranged from 6.6 to 8.1, whereas high TDS levels of 1390 mg/L and 1470 mg/L were observed in two boreholes. Three boreholes had higher electrical conductivity. Two boreholes had elevated nitrate levels of 15 and 21.5 mg/L. The high nitrate level correlates with the pH, EC, and TDS values. Our results suggest that high nitrate levels measured in communities’ boreholes pose ill health to the community, especially children, infants, and elders. Prenatal exposure to high nitrate has been found to have acute health effects in infants. Therefore, there is a need for further longitudinal studies on health risks among vulnerable groups in these communities.

The lordosis of the haemal part of the vertebral column is a frequent abnormality in reared fish. Haemal lordosis develops during the late larval and early juvenile period, mainly due to the high swimming activity of the fish in the rearing tanks. In the present study we examined whether haemal lordosis recovers during the growth of European sea bass. Furthermore, we aimed to develop simple morphometric indices (PrAn1 and PrAn2) that could link the severity of lordosis at the juvenile stage with fish morphological quality at harvesting. At 111 days post-hatching (dph, 53±4 mm standard length, SL), 600 seabass juveniles with lordotic (L, 200 fish) or normal (N, 400 fish) external morphology were selected and introduced in a common tank. At 150 dph (75±7 mm SL), 350 fish were randomly selected, pit-tagged and transferred in a sea cage for on-growing up to 502 dph (234±16 mm SL). The morphological examination of the fish at 150 and 502 dph revealed that the 60% (46 out of 77) of L juveniles turned into normal phenotype by the end of on-growing period. Interestingly, 56% of the fish with recovered external morphology (N-Rec) presented either a completely normal vertebral column (31%) or minor abnormalities of individual vertebrae (25%). Following the results of geometric morphometric analysis, the differences in the body shape between N-Rec and N fish were not significant (p&gt;0.05, canonical variate analysis). The examined morphometric indices were effective in discriminating the normal fish from the 58% (PrAn1) to 65% (PrAn2) of lordotic juveniles. Results are discussed with respect to the mechanism of lordosis recovery, as well as to their application for the quality control and cull out of the abnormal fish in the commercial hatcheries.

Additive manufacturing (AM) is a promising new technology that is having a very fast growth from home workshops to high-tech cutting-edge factories. As any manufacturing technique, adequate metrology services are needed to assure the quality of items manufactured by AM. One of the most widely used instruments to measure the characteristics of surfaces manufactured with AM is the confocal microscope. In this paper, authors present a whole calibration procedure for confocal microscopes designed to be implemented preferably in workshops or industrial environments rather than in research and development departments. Because of that, it is as simple as possible. The procedure is designed without forgetting any of the key aspects that need to be taken into account and based on classical reference material standards. These standards can be easily found in industrial dimensional laboratories and easily calibrated in accredited calibration laboratories.

Abstract: The contribution of breakfast to diet quality (DQ) can inform future dietary guidelines. This study examined breakfasts that were associated with highest-quality diets. Dietary data came from the first reported day of the National Health and Examination Survey (NHANES) 2011-2014 (n=14,488). DQ measures were the Nutrient Rich Foods Index (NRF9.3) and the USDA Healthy Eating Index 2015 (HEI 2015). Analyses of breakfast intakes were conducted by NRF9.3 tertiles and by age and socioeconomic groups. Four out of 5 NHANES participants ate breakfast. Breakfast provided 19-22% of dietary energy depending on age. Breakfast intakes of complex carbohydrates and total sugars were higher and intakes of protein and fats were lower relative to energy intakes. Breakfast provided more that 20% of daily intakes of B vitamins, vitamins A and D, folate, calcium, iron, potassium and magnesium. Eating breakfast was associated with higher NRF9.3d scores. Breakfasts associated with top tertile of NRF9.3d had more carbohydrates and less added sugars and fats. Such breakfasts had more fruit and juices, more whole grains, more milk and yogurt and less meat and eggs. Breakfast patterns that favored fruit, whole grains, and dairy were associated with healthiest diets.

The maternal death rate remains high in South Africa despite the availability of many existing strategies to improve the quality of service. A 30% increase in maternal mortality rate was reported between 2020-2021, with Limpopo ranking fourth highest out of nine provinces. Vhembe district remained number three with a high maternal death rate. This study explored strategies to reduce the maternal death rate and improve the provision of quality maternal healthcare services in selected hospitals of Vhembe district, Limpopo province. One hospital was purposively sampled from every four municipalities. A qualitative approach using phenomenological design was employed. Twenty-eight participants were sampled using a convenience sampling method. The semi-structured interview guide was used to collect data. An audio recorder was also used until data saturation. Data saturation was reached at the 20th participant, but the researcher continued until 28 sampled participants were interviewed. Interpretative phenomenological analysis was used following the analytical stages of interpretative data analysis. The study proposal was ethically cleared by the University of Venda Ethics Committee (FHS/22/PH/08/3108). Results indicate that despite implementing strategies to improve maternal healthcare services and reduce the maternal death rate, several factors, such as lack of material resources, shortage of staff, incompetent staff, and poor infection control, affect the quality of maternal health service in Vhembe district. Limpopo Department of Health and hospital management should ensure that hospitals have all necessary resources and support healthcare professionals through in-service training to ensure the functionality of existing strategies.

The representation of aerosols in climate-chemistry models is important for air quality and climate change research, but it can require significant computational resources. To overcome this, simpler modules such as modal aerosol modules with three lognormal modes (MAM3) can be used. In this study, the coupling of the Carbon Bond Mechanism, version Z (CBMZ), and MAM3 chemistry modules in WRF-CAM5 was improved by adding biomass-burning emissions to both gas- and particle-phase chemistry and incorporating a conversion mechanism between volatile organic compounds (VOCs) and secondary organic carbons (SOCs). The study conducted six simulations over the western U.S. and northeastern Pacific region and compared the model’s performance with observational benchmarks such as reanalysis, ground-based, and satellite data. The results showed that the model with enhanced chemistry capabilities had a 31% and 58% reduction in root-mean-square errors (RMSE) for black carbon (BC) and organic carbon (OC) surface concentrations, respectively. The earlier release of the WRF-CAM5 version had two deficiencies that were addressed in this study. This research highlights the importance of accurate aerosol representation in climate-chemistry models for improving accuracy and reducing errors in simulations.

This paper addresses the challenges of improving the accuracy of low-cost particulate matter sensors (LCPMS) under high humidity conditions. Such weather conditions often lead to the overestimation of particle counts due to hygroscopic particle growth, resulting in a potential public concern, although most of the detected particles consist of just water. The paper presents an innovative design for an indicative air-quality measuring station that integrates the particulate matter sensor with a preconditioning subsystem designed to mitigate the impact of humidity. The preconditioning subsystem works by heating the incoming air, effectively reducing the relative humidity and preventing the hygroscopic growth of particles before they reach the sensor. To validate the effectiveness of this approach, parallel measurements were conducted using both preconditioned and non-preconditioned sensors over a period of 19 weeks. The data was analyzed to compare the performance of the sensors in terms of accuracy for PM1, PM2.5, and PM10 particles. The results demonstrated a significant improvement in measurement accuracy for the preconditioned sensor, especially in environments with high relative humidity. When the conditions were too severe and both sensors started measuring incorrect values, the preconditioned sensor measured values were closer to the actual values. Also, the period of measuring incorrect values was shorter with the preconditioned sensor. The results suggest that the implementation of air preconditioning subsystems in LCPMS can provide a cost-effective solution to overcome humidity-related inaccuracies, thereby improving the overall quality of measured air pollution data.

Water quality assessment stands as a fundamental step in water resource management. In addition to substances and organisms present in the water, land use and land cover are two factors affecting also water quality. This study analyzed the correlation and influence between water quality and land use and land cover in the Miranda River Basin (MRB) and the natural wetlands in the Pantanal Biome. Using a watershed-wide approach, results suggested that water quality management policies can be considered in terms of sub-basins (smaller planning units). The Water Quality Index (WQI) was considered GOOD or EXCELLENT throughout the MRB. It was observed that the natural wetlands have the capacity to contribute to improve WQI, with reductions in thermotolerant coliforms and turbidity; however, high values were found for thermotolerant coliforms, a temporal increasing trend of biochemical oxygen demand (BOD), and a reduction in dissolved oxygen and total phosphorus. Conversely, it was found in these flooded areas a trend of decrease in dissolved oxygen and an increase in BOD concentrations. Natural wetlands play important hydrological and ecological roles in water quality, storing, removing, and cycling nutrients. They are highly relevant areas for defining watershed management and conservation strategies, environmental protection, and providing ecosystem services.

This paper evaluated the quality and suitability of surface water in the Vaalharts area, South Africa, for human consumption, drinking, and irrigation purposes. Water quality constituents include water pH, EC, TDS, HCO3-, Cl-, SO4, Mg, Ca, k, Na, NO3, F, Fe, PO4, As, Al, Mn, Cr, Cu, Zn, B, Cd, Hg, Pb, N, Sb, Se, and the biological parameter included E. coli along surface waters as well as canals and dams. Sodium Adsorption Ratio, Sodium Percentage, Permeability Index, Residual Sodium Carbonate, Kelley’s Ratio, Magnesium Hazard, and Potential salinity irrigation water parameters indicated that the majority of the water samples are suitable for irrigation. The water quality index values showed that the majority of the samples are unsuitable for drinking but suitable for irrigation and industrial uses. E. coli in the surface water samples in the study area show unsafe water quality with high and very high risk for human health. Based on the classifying criterion of the Heavy Metal Pollution Index and Heavy Metal Evaluation Index, all the water samples are above the critical limit, therefore, unsuitable for human consumption. The carcinogenic risk (CR) concentrations of As, Cr and Cd were above the target risk.

Abstract: Background: Recently, cardiorespiratory fitness (CRF) has been postulated as an adverse health outcome related to poor sleep quality. However, studies investigating the relationship between CRF with subjective sleep quality index are scarce. Thus, the current study aimed to investigate the association between CRF and Pittsburgh sleep quality index (PSQI) in apparently healthy people. The secondary aim was to investigate the association between reported physical activities (PA) and PSQI. Methods: 33 apparently healthy male participants volunteered to participate. CRF (VO2 peak) was measured via cardiopulmonary exercise testing on a treadmill. A short form of the International physical activity questionnaire (IPAQ) was used to measure PA, and PSQI was used for sleep quality index. Results: There was no correlation between CRF and PSQI total score or any component of the PSQI. Also, there was no correlation between IPAQ and PSQI total score. Categorical data analysis of the two questionnaires revealed that 45.5% of the participants reported low physical activity and poor sleep quality. Conclusions: There was no association between CRF, reported PA with subjective sleep quality index. The use of objective tools for assessing the quality and quantity of sleep should be recommended for future studies as it may clarify the association between CRF and sleep quality.

The study analyzed Ecuador's presence in the Web of Science (WoS) post-pandemic from a multivariate dynamic, highlighting a significant transformation in scientific communication towards open access (OA). The methodology integrated multivariate statistical techniques, using R and specialized tools, to process 9,085 relevant articles, 52% of the Ecuadorian publications in WoS between 2019 and 2021 were open access. This movement reflects a commitment to quality research and accessibility, showing an increase in publications and citations under OA. The research underscores the importance of establishing robust national OA policies in Ecuador to promote scientific collaboration and an equitable distribution of knowledge. Despite funding challenges and the lack of specific regulations, educational institutions in Ecuador have maintained a constant scientific output, adapting to the global environment and the demand for transparent information. The study concludes that there is an urgent need for a holistic approach to OA in the country, recognizing the progress made despite the difficulties.

Ethiopian Airlines is a leading airline in the world. Its supply chain management is one of the most critical aspects in achieving its sustainability objectives. The present study aims to assess the sustainability practices and strategies of Ethiopian Airways in its supply chain, identifying areas for improvement and recommending strategies for enhancing sustainability. The study concentrates on pertinent sustainability concerns within the aviation sector while examining antecedent research on the sustainability of Ethiopian Airlines’ supply chain management strategies. The findings of the study reveal that there are several areas in need of improvement, including the implementation of waste reduction measures, the establishment of a recycling program, and the reduction of single-use plastic usage. It is suggested that promoting responsible tourism embodying sustainable practices is imperative, particularly within the airline context.

This study aimed to analyse the variation of recreational water quality in Plettenberg Bay in an attempt to comprehend the effects of pollution on the environment, and more specifically the potential impacts on the quality of surface water used for recreational activities. Plettenberg Bay is a major destination for tourists in South Africa, with recreational water activities representing an important attraction. For this study, data were obtained from Bitou Municipality, the local au-thority in charge of the water monitoring program in Plettenberg Bay. The selected datasets contained water quality data collected by the Bitou Municipality waterworks department in three sampling sites in Plettenberg Bay. The samples were tested for six water quality parameters namely, Ammonia, Suspended Solids, Conductivity, Nitrates/Nitrites, pH, and E coli. Water quality trends appeared stabile over the five years, with only a few parameters showing variation in their concentration levels. It is recommended that the Bitou Municipality increase the sampling frequency to allow a clearer understanding of water quality variation and to minimise potential uncertainties.

Keywords:

Introduction: The majority of epidemiological reports focus on confirmed cases of COVID-19. In this study, we aim to assess the health and well-being of adults not infected with Covid-19 after two months of quarantine in Morocco. Materials and methods: Two months after the declaration of quarantine in Morocco following the Covid-19 epidemic, we carried out a descriptive cross-sectional study of 279 Moroccan citizens. We used the Short Form Health Survey (SF-12) as a determinant of quality of life, which is based on eight dimensions of health. The data were collected using an electronic questionnaire distributed online. The participants also indicated their socio-demographic data, their knowledge and practices regarding the Covid-19 pandemic and whether they had chronic health problems. Results: The quality of life of all participants was moderately disrupted during the Covid-19 pandemic with a mental health score (MCS) of 34.49 (± 6.44) and a physical health score (PCS) of 36.10 (± 5.82). Participants with chronic diseases scored lower with 29.28 (± 1.23) in mental health (MCS) and 32.51 (± 7.14) in physical health (PCS). The seriousness of COVID-19 has an impact on the quality of life and health well-being of people and this impact is more marked in people with chronic health problems. Conclusion: Our results confirm the need to pay attention to the health of people who have not been infected with the virus. Our results also point out that uninfected people with chronic illnesses may be more likely to have well-being problems due to quarantine restrictions.

Wagyu beef is gaining worldwide popularity, primarily due to the fineness of its marbling. Cur-rently, the evaluation of this marbling is performed visually by graders. This method has several issues: varying evaluation standards among graders, reduced accuracy due to long working hours and external factors causing fatigue, and fluctuations in grading standards due to the grader's mood at the time. This paper proposes the use of fractal analysis for the grading evaluation of beef marbling to achieve automatic grading without the inconsistencies caused by human factors. In the experiments, cross-sectional images of the parts used for visual judgment were taken, and fractal analysis was performed on these images to evaluate them using fractal dimensions. The results confirmed a correlation between the marbling evaluation and the fractal dimensions, demonstrating that quantitative evaluation can be achieved, moving away from qualitative visual assessments.

Plato defined a quality as “some degree of perfection” [49]. Studies on quality have unveiled the internal and external quality factors [17] that significantly impact product quality [4]. Internal factors are invisible to the end customer and are dependent on overall work organisation by the development team [17]. This work organisation is called “the process” [11],[33]. In this article, we will discuss how to address the drone-dedicated software development process to support system verification and ensure product quality by supporting quality characteristics and therefore increase software development awareness and control. We will discuss the process's influence on overall work activities and relationships between those activities by addressing the software development process utilised in the drone-dedicated GNSS-denied navigation system development project. The result was observable after three weeks of starting the software development. It was focused on better team awareness, faster task completion, lower number of development mistakes, and better and faster change response than we observed in other projects that didn’t follow the predefined process.

Brand trust holds significant importance in the Mongolian cashmere industry. This study examines the primary predictors of customer brand trust among Mongolian cashmere users. Our research includes a survey with 800 participants and 20 individual interviews conducted among both Mongolian cashmere users and non-users. We utilized an online platform to reach participants, employing convenience sampling. The study investigates the relationship between various factors and brand trust within the context of Mongolian cashmere brands. Through a combination of in-dividual interviews and statistical analysis, we test six hypotheses. The findings indicate that higher brand quality, a strong reputation, greater transparency, effective issue resolution, commitment to environmental and social responsibility, and pre-purchase research on such commitments positively impact brand trust. Key insights gleaned from the interviews emphasize the importance of quality, reputation, transparency, customer service, and environmental responsibility in shaping consumer trust. These results offer valuable implications for cashmere brands aiming to bolster consumer trust and foster loyalty.

Recently, there has been a trend towards healthy food. Consumers are looking for products that have health-promoting properties in addition to their taste. Actinidia fruit, apart from being tasty, contains valuable nutrients. They are high in vitamin C, polyphenols, and pectins and low in calories. These pro-health properties allow kiwiberry fruit to qualify in the group of so-called superfoods. All tested cultivars belong to two species of Actinidia, well tolerating conditions of moderate climate with negative temperatures in winter. The cultivars differed significantly in mineral content, color, firmness, weight and content of antioxidant substances. Summer pruning (lightening) increased the content of N, P, K, extract, and NO3 and resulted in darker fruit color. However, it slightly decreased the content of polyphenols. 'Sientiabrskaja' can be recommended for consumption as the cultivar richest in polyphenols and with the highest health-promoting values.

In the search for more efficient production systems, many changes have occurred in the strawberry production sector. Planting density is one of the management techniques that most interferes with the quality of fruits and production aspects. This study aimed to evaluate the effect of different planting densities on the photosynthetic characteristics, fruit quality, and production of the strawberry cultivar Pircinque. The study was conducted in the 2018/2019 and 2019/2020 harvests in Lages, Santa Catarina, Brazil. The treatments consisted of plant spacing of 5, 10, 15, 20, 25, and 30 cm. The experimental design was in randomized blocks, with four blocks and plots of 20 plants. Plant spacing interfered with fruit quality, photosynthetic efficiency, production, productivity, and economic return. Due to the fruits of 'Pircinque' with higher quality than other cultivars, the planting spacing between 5 and 15 cm allows meeting the fruit's main production and quality requirements. However, it is up to the producer to adapt the management if opting for higher planting densities, which allow greater economic viability of the business.

This manuscript explores sustainable agriculture's role in mitigating environmental challenges and meeting the nutritional needs of a growing global population. The objective is to assess the impact of different fertilizers on two distinct tomato-growing soils, each characterized by unique chemical and biological properties. The study compares four fertilizer treatments: Additionally, it evaluates the environmental implications of these fertilizers, focusing on their Carbon and Water Footprints. The findings indicate significant improvements in soil quality with SBO fertilizer. Both soils experienced a shift towards a near-neutral pH, increased organic matter content, and heightened microbial biomass. Enzyme activities were notably superior in SBO-treated soils. Life Cycle Assessment (LCA) results demonstrate that the SBO-based system is the most sustainable, with the lowest Carbon footprint. NPK exerts the highest environmental impact. The Water Footprint analysis aligns with these results, showing that SBO requires the least water for tomato production. In summary, this study underscores the significance of sustainable fertilization practices in improving soil quality and reducing environmental footprints in agriculture, offering potential benefits for food production and environmental conservation.

The aim of this study was to identify differentially expressed genes, biological processes and metabolic pathways related to adipogenesis and lipogenesis in calves receiving different diets during the cow-calf phase. Forty-eight uncastrated F1 Angus × Nellore males were randomly assigned to two treatments from 30 days of age to weaning: no creep feeding (G1) or creep feeding (G2). After weaning, the animals were feedlot finished for 180 days and fed a single diet containing 12.6% forage and 87.4% corn-based concentrate. Longissimus thoracis muscle samples were collected by biopsy at weaning for transcriptome analysis by RNA-Seq and at slaughter for the measurement of intramuscular fat content (IMF) and marbling score (MS). Animals of G2 had 17.2% and 14.0% higher IMF and MS, respectively (P &lt; 0.05). We identified 947 differentially expressed genes (log2 fold change 0.5; FDR 5%); of these, 504 were up-regulated and 443 were down-regulated in G2. Part of the genes up-regulated in G2 were related to PPAR signaling (PPARA, SLC27A1, FABP3, and DBI), unsaturated fatty acid synthesis (FADS1, FADS2, SCD, and SCD5), and fatty acid metabolism (FASN, FADS1, FADS2, SCD, and SCD5). Regarding biological processes, the genes up-regulated in G2 were related to cholesterol biosynthesis (EBP, CYP51A1, DHCR24, and LSS), unsaturated fatty acid biosynthesis (FADS2, SCD, SCD5, and FADS1), and insulin sensitivity (INSIG1 and LPIN2). Cow-calf supplementation positively affected energy metabolism and lipid biosynthesis, and thus favored the deposition of marbling fat during the postweaning period. Here it was shown, in an unprecedented way, by analyzing the transcriptome, genes, pathways and enriched processes due to the use of creep feeding.

Image fusion is a useful tool for producing a high-resolution multispectral image to be used for land use and land cover mapping. In this study, we use nine pansharpening algorithms namely Color Normalized (CN), Gram-Schmidt (GS), Hyperspherical Color Space (HCS), High Pass Filter (HPF), Nearest-Neighbor Diffusion (NND), Principal Component Analysis (PCA), Resolution Merge (RM), Stationary Wavelet Transform (SWT), and Wavelet Resolution Merge (WRM) to fusion Worldview-3 multispectral Bands and panchromatic band. In spectral and spatial fidelity, several image quality metrics are used to evaluate the performance of pansharpening algorithms. The SWT and PCA algorithms showed better results compared to other pansharpening algorithms while GS and CN algorithms showed the worst results for the original image fusion. The effect of fusion on each band was separately investigated and according to the calculations, we found that the CoastalBlue band and the Blue band showed the best result and the NIR-1 band and NIR-2 band show the worst result for the original image fusion. In the end, we conclude that the choice of fusion method depends on the requirement of remote sensing application.

Taste and smell function decline with age, with robust impairment in the very old. Much less is known about taste and smell function in young and middle old. We investigated taste and smell sensitivity via thresholds in a sub-sample of the NutriAct Family Study (NFS), the NFS Examinations cohort (NFSE; N=251, age M=62.5 years). We examined different aspects relating to taste and smell function: the degree to which taste and smell sensitivity relate to another and to taste and smell preferences, the role of gender and age, as well as effects on Quality of Life (QOL). Taste thresholds were highly correlated but no correlation was observed between taste and smell thresholds and between thresholds and preference. Women were more sensitive for both taste and smell than men. We found no effect of age on sensitivity and no effect of sensitivity on QoL. All null-findings were corroborated with Bayesian statistics providing evidence for the null hypotheses. Together our results indicate the independence of taste and smell despite their overlap during sensorial experiences. We found no evidence for age-related sensory decline, which could be due to our sample´s characteristics of non-clinical volunteers with good dental health and 93% non-smokers.

The article "Ensuring Quality Medicine is Not a Single Event but a Combined Effort of a Pharmaceutical Company" explores the multifaceted approach required to maintain high standards in pharmaceutical manufacturing. It emphasizes that quality assurance in medicine production is not an isolated event but a continuous, integrated process involving multiple departments and stages. The article highlights the roles of research and development, rigorous clinical trials, regulatory compliance, and robust manufacturing practices in ensuring the efficacy and safety of medicines. It also discusses the importance of quality control measures, such as stringent testing protocols and regular audits, to detect and mitigate potential issues early. The collaboration between different teams within a pharmaceutical company, including scientists, engineers, and quality assurance professionals, is crucial for sustaining quality throughout the product lifecycle. Moreover, the article addresses the necessity of adhering to global standards and guidelines, such as Good Manufacturing Practices (GMP), to ensure consistency and reliability in drug production. By fostering a culture of continuous improvement and vigilance, pharmaceutical companies can effectively safeguard public health and maintain trust in their products. This holistic approach underscores that delivering quality medicine is an ongoing commitment requiring coordinated efforts across the entire organization.

With an increased interest in applications that require a clean background image, such as video surveillance, object tracking, street view imaging and location-based services on web-based maps, multiple algorithms have been developed to reconstruct a background image from cluttered scenes. Traditionally, statistical measures and existing image quality techniques have been applied for evaluating the quality of the reconstructed background images. Though these quality assessment methods have been widely used in the past, their performance in evaluating the perceived quality of the reconstructed background image has not been verified. In this work, we discuss the shortcomings in existing metrics and propose a full reference Reconstructed Background image Quality Index (RBQI) that combines color and structural information at multiple scales using a probability summation model to predict the perceived quality in the reconstructed background image given a reference image. To compare the performance of the proposed quality index with existing image quality assessment measures, we construct two different datasets consisting of reconstructed background images and corresponding subjective scores. The quality assessment measures are evaluated by correlating their objective scores with human subjective ratings. The correlation results show that the proposed RBQI outperforms all the existing approaches. Additionally, the constructed datasets and the corresponding subjective scores provide a benchmark to evaluate the performance of future metrics that are developed to evaluate the perceived quality of reconstructed background images.

The agricultural sector faces challenges due to climate change and the growing global population. Alkaline stress could adversely impact plant growth and crop production. This stressor diminishes water quality essential for crop cultivation, consequently impairing plant growth and overall productivity. Gamma-aminobutyric acid (GABA), a non-protein amino acid, may exhibit multifaceted roles in plant responses to adverse environmental conditions. Optimization of crop production in controlled environmental agriculture under artificial light attracted much attention. In the present study, we investigated the effects of different light spectra and GABA concentrations on Lollo Rosso lettuce plants under alkaline stress. Seedlings were placed under different light spectra [red (R), blue (B), white (W), 3R:1B, and 2R:1B:1far-red (FR)] and treated by GABA (0 and 50 µmol). Alkaline conditions were instituted by applying NaHCO3 at a concentration of 40 mM. The experiment incorporated a control treatment without NaHCO3. In general, R light exposure caused the highest growth performance of lettuce plants. GABA augmented biomass production in control and alkaline-treated plants across all light spectra. Additionally, it increased the concentrations of photosynthetic and protective pigments under alkaline conditions. GABA also improved the photosynthetic performance under all light spectra. Non-photochemical quenching and pigmentation were enhanced by exposure to B light, especially in plants treated with GABA. Alkaline stress induced an increase in soluble carbohydrate content in the lettuce leaves. These findings highlight the support of GABA application in facilitating coping plants to alkaline stress.

The work focuses on the possibility of application of tunable magnetic devices in electrical power systems with adaptive features. The idea underlying this type of operation, which depends on interaction with magnetic fluxes in a quassi-linear range of magnetic core characteristics, is a new approach to the design of magnetic elements. The suitable examples of adaptive electrical power systems can be devices for improving the quality of electricity. When used in compensators of reactive power or both reactive and distortion power, tunable magnetic devices offer much wider possibilities for the compensation, compared to “standard“ solutions, involving compensators based on fixed inductors. Nevertheless, the application of the proposed device in electrical systems such as is only an example of its possible implementations in the area of electrical power. In this work the following issues are covered: exemplary solution of an adaptive ‘passive’ compensator, rules for the operation of tunable magnetic device, and results investigation of the laboratory model of an electrical system based on such device.

The greater Wellington region, New Zealand, is highly vulnerable to large earthquakes because it is cut by active faults. Bulk water supply pipelines cross the Wellington Fault at several different locations, and there is considerable concern about severe disruption of the provision of reticulated water supplies to households and businesses in the aftermath of a large earthquake. A number of policy initiatives have been launched encouraging householders to install rainwater tanks to increase post-disaster resilience. However, little attention has been paid to potential health hazards associated with consumption of these supplies. To assess health hazards for householders in emergency situations, six 200-litre emergency water tanks were installed at properties across the Wellington region, with five tanks being allowed to fill with roof-collected rainwater and one tank being filled with municipal tapwater as a control. Such tanks are predominantly set aside for water storage, and once filled, feature limited drawdown and recharge. Sampling from these tanks was carried out fortnightly for one year, and samples analysed for E. coli, pH, conductivity, a range of major and trace elements, and organic compounds, enabling an assessment of the evolution of water chemistry in water storage tanks over time. Key findings were that the overall rate of E.coli detections in the rain-fed tanks was 17.7%, which is low in relation to other studies. We propose that low incidences of E.coli may be due to biocidal effects of high zinc concentrations in tanks, originating from unpainted galvanised steel roof cladding. Lead concentrations were high compared to other studies, with 69% of rain-fed tank samples exceeding the World Health Organisation’s health-based guideline of 0.01 mg/L. Further work is required to determine risks of short-term consumption of this water in emergency situations.

Background: Since 2010, Burkina Faso has developed and initiated community-based management of childhood illnesses. Following the increased presence of community health workers and the adoption of free community health care, this study aims to assess community satisfaction with curative care administered by community health workers. Methodology: It was a descriptive and analytical cross-sectional study. Data were collected in the health districts of Boussé and Boussouma from 20 February to 30 March 2023 for quantitative data and from 12 to 30 January 2024 for qualitative data using a questionnaire (household survey) and an interview grid (focus groups). Analyses were conducted using SPSS IBM 25 and Nvivo 14. Results: Households benefit from oral curative care when using CHWs, but are not satisfied with the temporal accessibility of these community health workers. Temporal accessibility and awareness during care have a significant influence on household satisfaction. Conclusion: Curative care by community health workers is effective, but its use could be improved by addressing the unavailability of community health workers, inputs and better communication during care.

ABSTRACT Lubricants play a crucial role in reducing friction and wear between surfaces in relative motion. Engine oil, as a lubricant, is specifically designed to minimize friction and wear between the moving parts of different equipment and machinery. Engine oil blending serves the purpose of adjusting the variety of lubricants available to meet specific performance requirements. Through blending, it is possible to tailor the characteristics of the lubricating oil, such as viscosity, stability, and additive content, to optimize its effectiveness in reducing friction, protecting engine components, and enhancing overall equipment performance. By customizing lubricant formulations through blending, manufacturers can address the diverse lubrication needs of modern engines and machinery, ensuring smooth operation, longevity, and efficiency.To enhance the quality of the lubricant and achieve the desired high-performance multi-grade engine oil, a systematic approach was followed. The process began with testing the specific gravity of the oil using a hydrometer and thermometer to ensure accurate measurements. Subsequently, 5 liters of base oil were carefully measured and poured into a stainless steel reactor pot to serve as the blending vessel. Following this, 1 liter of paraffin oil (100N) was added to the base oil to introduce specific properties to the blend. To further optimize the formulation, 0.42 kg (7% of the total blend) of additives, including a selection of specific performance-enhancing compounds, was incorporated. These additives, such as Aspen, Tackifier, and other essential components like anti-wear, corrosion inhibitors, detergents, dispersants, and antioxidants, were meticulously measured and added to the mix. Through this precise blending process, the goal was to craft a high-quality multi-grade engine oil that meets the stringent performance requirements for various operating conditions and equipment types. After the melted Aspen and dissolved tackifier were added to the mixture, thorough stirring was carried out to ensure uniform distribution until a homogeneous blend was achieved. The mixture was then exposed to heat to facilitate the reaction between the base oil and additives, reaching a temperature of 70°C for optimal blending. Subsequently, 0.5 kg of viscosity index improver was introduced into the mixture and stirred continuously for a period of 5 minutes to ensure proper integration. Following this step, 5 grams of dye were carefully added to the mixture, and stirring was continued to evenly disperse the coloring agent throughout the blend. This meticulous process aimed to ensure that all components were effectively incorporated, facilitating the production of a high-quality, customized multi-grade engine oil with enhanced performance characteristics and optimal lubricating properties. After subjecting the mixture to a temperature of 70°C, the heat source was removed, allowing the product to gradually cool down to room temperature, which was estimated to be around 30°C. Following this cooling process, the product underwent a filtration step to remove any residual impurities present in the mixture. A sample of the purified product was then extracted for further analysis. Quality control tests were meticulously carried out on the sample to ensure that the product met the rigorous standards set by the Standard Organization of Nigeria (SON). The results obtained from the quality control tests were highly promising, indicating that the product indeed complied with the stringent specifications outlined by the regulatory body. This adherence to quality standards is essential in ensuring the product's reliability and performance in various applications. The successful outcome of the quality control test underscores the meticulous attention to detail and commitment to excellence in the production process. The rigorous quality control procedures implemented in the analysis of the product highlight the commitment to upholding high standards of quality and safety in the manufacturing process. By consistently meeting and exceeding industry regulations and standards, the product not only demonstrates its reliability but also reflects a dedication to customer satisfaction and product excellence. The adherence to the SON standards showcases a commitment to producing top-quality products that meet the needs and expectations of consumers and industry stakeholders alike.

Machine performance modeling and optimization have emerged as crucial steps for process enhancement and efficiency. This study explored machine learning to model and optimize the cassava grating chamber of cassava grater for the quality production of gari. This domain remains unexplored thus far. A total of 196 graters were studied. Key variables studied included tooth diameter (TD), tooth height (TH), inter-tooth spacing (ITS), drum speed (DS), clearance (C), and moisture content of cassava (MC). Geometric mean diameter (GMD) represented mash quality. Feature importance rankings emphasized TH (0.488784), C (0.243284), TD (0.112682), ITS (0.103547), DS (0.036261), and MC (0.015442) in determining particle size (GMD) of grated mash. Machine learning models efficiently interpreted these attributes, including gradient boost regressor, linear regression, neural network, and random forest. The gradient boost regressor was the best predictive model, achieving 95.34% accuracy, RMSE (0.3291), and MAE (0.2303). The study provides a GMD predictive equation and optimized parameters for specific gari size production, offering valuable insights for tailored machinery in the cassava grating activity.

Background: External beam radiation therapy requires a sophisticated and laborious planning procedure. To improve the efficiency and quality of the planning procedure, machine learning predictions of the dose distributions have been introduced to speed up the planning procedure and to serve as quality assurance. The most recent dose prediction models are based on deep learning U-Nets that give good approximations of the dose in 3D almost instantly. It is our purpose to train a 3D dose prediction for glioblastoma VMAT treatment and test its robustness and sensitivity for the purpose of quality assurance of automatic contouring. Methods: From a cohort of 125 glioblastoma (GBM) patients, VMAT plans were created according to a clinical protocol. The initial model was trained on a concatenated 3D U-Net. A total of 60 cases were used for training, 15 for validation and 20 for testing. The prediction model was tested for sensitivity to dose changes according to realistic contour variations. Additionally, the model was tested for robustness by exposing it to a worst-case test set containing out-of-distribution cases.Results: The initially trained prediction model had a dose score of 0.94 Gy and a mean DVH score for all structures of 1.95 Gy. In terms of sensitivity, the model was able to predict the dose changes that occurred due to the contour variations with a mean error of 1.38 Gy.Conclusions: We obtained a 3D VMAT dose prediction model for GBM with limited data, providing good sensitivity to realistic contour variations. We tested and improved the model's robustness, by targeted updating the training set, making it a useful technique for dose awareness in the contouring evaluation and quality assurance.

Space syntax can be potentially applied for the evaluation of quality of user flows particularly in solving problems of sustainable projects in spaces intended for users to move around. This study aims to analyze the concepts of pedestrian flows (open and closed) by space syntax based bibli-ographical approach on a global scale, demonstrating the capability of improvements in Sus-tainable Development Goals (SDGs) as applied to the architecture of sustainable flows. Scopus theoretical reference bases were used, which are directly related to the theme of space syntax in open and closed spaces. Frequency analyzes were carried out, applying the content analysis, to identify words with a degree of similarity, related to “space syntax: flow in urban environ-ments” and “space syntax in closed built systems”, in relations to the SDGs. The results show that pedestrian flows identified in the literature aid to understand the global production on space syntax in open and closed spaces, directed to user flows in the built environment, where many environments of flows in the built space analyzed become unsustainable because they do not present full flow efficiency. In our study on space syntax, the following central terms were identified: pedestrian movements (open urban systems) and space (closed built systems), which allows a better understanding of the flows, highlighting the importance of the urbanist architect on the functionality of user flows in sustainable architectural projects on a global scale. The most frequent categories for open environments were the terms space and form and for closed envi-ronments were space and flow.

Data-driven models based on artificial intelligence are efficiently used to solve complex problems. The quality of groundwater is of utmost importance, as it directly impacts human health and the environment. In major parts of the world groundwater is the main source of drinking water, it is essential to periodically monitor water quality. Conventional water quality monitoring techniques involve periodical collection of water samples and analysis in the laboratory. This process is expensive, time consuming and involves lot of manual labor. The aim of our study is to build an ant colony optimized neural network for predicting groundwater quality parameters. We have proposed artificial neural network comprising of six hidden layers. The approach was validated using our groundwater quality dataset of a hard rock region in the northern part of Karnataka, India. Groundwater samples were collected by us periodically from March 2014 to October 2020 from 50 wells in this region. These samples where analysed for measuring the pH, Electrical Conductivity, Na+, Ca+, Na+, K+, Mg2+, F-, Cl- and U+. The temporal dataset was split for training, testing and validation of our model. Metrics such as R2 (Coefficient of Determination), RMSE (Root Mean Squared Error), NSE (Nash–Sutcliffe efficiencies) and MAE (Mean Absolute Error) were used to evaluate the prediction error and model performance. These performance evaluation metrics indicated the efficiency of our model in predicting the temporal variation in groundwater quality parameters. The method proposed by us can be used for prediction and the temporal frequency of sample collection can be reduced to save time and cost. The results also confirm that the combination of artificial neural network with ACO is a promising tool to optimize weights while training the network, and hence will help in reasonable prediction of groundwater quality parameters.

Background: Exercise is an accepted intervention to improve the quality of life (QoL) of breast cancer patients. Exercise programs have been developed and all have shown satisfactory results in improving QoL. There is a lack of research comparing different prescription modalities. The aim of this study is to evaluate the effectiveness of physical exercise (in-person, home-based, prescription) on QoL in breast cancer patients actively undergoing treatment; Methods Quasi-experimental study with randomized assignment to three groups (in-person: guided and supervised in-person exercise program; home-based exercise: guided and supervised exercise program with streaming monitoring; recommendation: exercise recommendation). Quality of life was measured using the QLQ-C30 questionnaire. Baseline and 24-week analysis. Results: The total sample analyzed was n=80. QoL improved significantly at 24 weeks in the face-to-face and home-based exercise groups, but not in the advice group. Exercise in all modalities improved fatigue, nausea, vomiting, appetite, and constipation. QoL at 24 weeks depended on active chemotherapy, tumor type, and assigned exercise group (r2 = 0.503; p &lt; 0.001). Conclusions: QoL in breast cancer patients undergoing active treatment improves after a 24-week exercise program, especially in face-to-face and home-based exercise. Home-based exercise, streaming-based recommendation is a viable option for exercise recommendation.

Efforts to enhance carbon storage in forest ecosystems through policy and management decisions rely on accurate forest biomass assessments. However, most forest inventories consider tree mortality the only form of aboveground biomass loss, overlooking other important factors, such as wood decay in living trees. In this study, using linear mixed-effects models, we delve into the sustainability of mature and over-mature deciduous forests in Latvia by conducting a comprehensive analysis of stem rot severity, identifying species for which the impact of stem rot on their carbon stock reduction was most significant. The analysis focused on determining the proportion of discolored wood, decomposed wood, and hollow spaces within the stems of 190 living deciduous trees commonly found in hemiboreal forests. The study reveals a greater extent of stem rot and more extensive decay in Populus tremula trees than in Betula spp., Alnus glutinosa, and Alnus incana. It emphasizes the influence of tree species, age, and diameter at breast height on stem rot proportions. The stump rot area significantly predicts the amount of decomposed and discolored wood within the stem. The study provides valuable insights for sustainable forestry practices and highlights challenges in estimating stem rot severity, emphasizing the need for comprehensive diagnostic methods.

This qualitative study explores supplier selection criteria from the perspectives of procurement professionals across diverse industries. Supplier selection is crucial for organizational efficiency and performance, influenced by factors beyond traditional cost considerations. The research aims to uncover nuanced criteria such as quality assurance, supplier reliability, innovation capability, sustainability practices, strategic alignment, relational dynamics, and risk management strategies. These criteria reflect a shift towards holistic evaluation frameworks that integrate economic, social, and environmental dimensions in procurement decision-making. Methodologically, the study employed semi-structured interviews with 30 procurement professionals, ensuring depth and diversity in perspectives. Thematic analysis was used to identify recurring themes and patterns, illuminating the complexities and strategic importance of supplier selection processes. Findings highlight the strategic role of suppliers in driving innovation, enhancing supply chain resilience, and supporting organizational goals. Moreover, the study underscores the significance of sustainable sourcing practices, ethical considerations, and effective supplier relationships in fostering long-term partnerships and mitigating operational risks. Practical implications suggest that organizations should adopt integrated approaches to supplier selection, leveraging data-driven insights and technological advancements to optimize decision-making. By prioritizing strategic alignment, fostering collaborative partnerships, and implementing robust risk management strategies, organizations can navigate uncertainties, capitalize on market opportunities, and sustain competitive advantage.

The increasing availability of longitudinal data (repeated numerical observations of same units at different times) requires the development of flexible techniques to automatically detect common errors in such data. Besides obvious and easily identifiable cases, such as missing or out-of-range data, large longitudinal dataset often present problems not easily traceable by the techniques used for generic datasets. In particular, elusive and baffling problems are i) inversion of one or more values from one unit to another; ii) anomalous jumps in the series of values, iii) errors in the timing of the values due to a recalculation operated by the data providers to compensate previous errors. This work proposes a statistical-mathematical approach based on a system of indicators that is able to capture the complexity of the described problems by working at the formal level, regardless of the specific meaning of the data. The proposed approach identifies suspect erroneous data and is applicable in a variety of contexts. We implement this approach in a relevant database of European Higher Education institutions (ETER) by analyzing Total academic staff, that is one of the most important variables, used in empirical analysis as proxy of size and also considered by policy makers at European level.

In the process of image feature extraction, noise in the image will greatly affect the accuracy of edge detection. In this paper, the image is filtered to remove noise before edge detection by using the algorithm of wavelet transformation. Different wavelet functions are used to decompose image. Based on the experimental results, the best denoising wavelet function is selected. Canny algorithm is used to detect the edge of the denoised image, and the result of edge detection is evaluated according to the Pratt quality factor. It is proved that wavelet transform can improve the edge detection results.

Water, soil/sediment, and 36 fish samples were collected at three major sites along Flint Creek in 2015-2016 and analyzed for total organic carbon (TOC), dissolved organic carbon (DOC), total mercury (tHg), and other water quality indicators. This study was a follow-up to a 2012 study that revealed elevated tHg levels in fish, resulting in a public health advisory. This study revealed tHg concentrations in water below the detection limit (0.0002 ppm); while, tHG in soil/sediment ranged from < 0.0133 ppm to 0.0682 ppm dry weight. No temporal trends existed, but tHG tended to increase with TOC. Mercury levels in sediment were below the threshold effects level suggested as a preliminary screening level by the National Oceanic and Atmospheric Administration (acute = 1.4, chronic = 0.77 ppb). In summary, tHg levels were low; posing little risk to drinking water. Soil/sediment levels were generally higher and could pose risk to aquatic species.

Objective: This study aims to investigate the effects of acupuncture therapy on the quality of life, early recurrence rate, and heart rate variability in patients following radiofrequency ablation for atrial fibrillation, as well as to assess its safety. Methods: Seventy patients were enrolled in this study. Of these, 35 patients received acupuncture treatment post-radiofrequency ablation, forming the experimental group, while the remaining 35 patients received sham acupuncture treatment, constituting the control group. The acupuncture group targeted the Xinju (BL15), Neiguan (PC6), and Shenmen (HT07) points, whereas the sham acupuncture group received sham interventions at three non-meridian and non-acupoints. Both groups underwent acupuncture treatment twice weekly for a total of 24 consecutive sessions. After three months, the total scores on the Atrial Fibrillation Specific Quality of Life Scale (AFEQT)—including symptom scores, daily activity scores, treatment anxiety scores, atrial fibrillation control scores, and symptom improvement satisfaction scores—along with atrial fibrillation burden and satisfaction scores, were compared between the two patient groups. Additionally, the recurrence rate of atrial fibrillation, frequency of hospitalizations due to arrhythmia, and incidence of adverse events occurring three months post-catheter ablation were also assessed. No significant differences were observed in the general baseline characteristics between the two groups. Results: The total AFEQT scores—including symptom scores, daily activity scores, treatment anxiety scores, atrial fibrillation control scores, and symptom improvement satisfaction scores—were significantly higher in both groups post-treatment compared to pre-treatment. Notably, patients in the experimental group exhibited statistically significant improvements in daily activity scores, treatment anxiety scores, and symptom improvement satisfaction scores compared to those in the control group (P<0.05). There were no statistically significant differences between the two groups regarding other measured outcomes. Conclusion: Acupuncture-assisted treatment of atrial fibrillation can improve the clinical efficacy of drugs and catheter ablation, help maintain sinus rhythm, increase sinus rhythm conversion rate, reduce ventricular rate, and shorten conversion time, and is safe and reliable.

Recognizing the critical impact of environmental factors on individuals, this study explores the relationship between environmental indoor pollutants (PM1, PM2.5, PM10, and CO₂) and students' basic emotional responses based on Ekman’s categorization. Conducted in a secondary school in Spain, it integrates IoT and image processing technologies to monitor air quality and emotions in real-time. Participants included 76 secondary school students and three teachers, with data collected over two months. The results showed significant correlations between PM levels and negative emotions such as anger and disgust, while CO₂ levels were associated with both negative and positive emotions, including happiness. Regression models demonstrated that environmental variables significantly predict basic emotions, highlighting the influence of indoor air quality. These findings emphasize the need for proactive air quality management in educational settings to enhance learning environments and support students' emotional well-being.

Studies carried out have revealed that every day around three thousand and twelve people lose their lives in the world due to traffic accidents and poor air quality. Large cities, with their millions of inhabitants and vehicles, face many problems relating to vehicular traffic. In 2015 the speed limit was modified on several roads in the city of São Paulo-Brazil. However, in 2017 the speed limits were increased again, but not on all previous routes. This study analyzed the impact of this change on the number of accidents and pollutant concentrations, over a period of ten years, comparing the periods before and after the implementation of the measure, using real data collected and provided by the authorities of the city and the state transit and environmental companies, on more than forty routes and two nearby air quality stations. The results show a clear reduction in the number of accidents without victims on the roads of the city of São Paulo starting in 2010. However, the restrictive measures imposed by government officials may have contributed to the decrease in the number of accidents, but the number of fatalities has not changed much. Air pollution has not improved substantially with speed changes, as new speed increases have been linked to new episodes of congestion. The average number of fatalities due to accidents has been increasing since 2010 and accidents are becoming more serious. The application of a general linear statistical model (GLM) estimated the impact of the speed reduction policy in terms of the number of injuries avoided per month: 43.4 and 14.1 on other roads and on Pinheiros marginal, respectively. The results highlight the need for a constant data collection by the authorities in cities with high vehicle traffic. The important temporal time trend in terms of reduction of injuries but not in terms of fatalities and air quality, shows the need to apply joint public policies, not only speed reduction, but also the use of new technologies and raising drivers’ awareness of the problem.

Background: Quality of life (QoL) in IC/BPS patients is an evidence gap in guidelines, because studies are limited and outdated. Therefore, guidelines might not reflect the current situation accurately, and no possible improvements in QoL of these patients. Secondly, guidelines suggest multimodal approach in therapy, however unknown is how the efficacy of these therapies are perceived by the patient themselves. The aim of this study is to investigate the perception of IC/BPS patients on their QoL and to determine which treatments they received and how they evaluate the efficacy of these various (alternative) therapies.Methods: Quantitative retrospective database study in IC/BPS patients, compiled of existing patient survey data (n=217) from July 2021. Results: The QoL of patients is affected significantly by IC/BPS. This is evident from the substantial self-reported impact by patients, the various affected domains on EQ-5D 5L. The QoL was not negatively affected by delayed diagnosis, but there were differences between female and males. Secondly, there was the wide array of (alternative) treatments utilized, although some have doubtful results and high dropout rates. Conclusion: QoL is considerably impaired in IC/BPS patients. Coagulation therapy and intravesical GAG therapy were most appreciated treatments. The diverse responses and adherence to various treatments warrant a personalized approach (phenotype-oriented therapy). To achieve improvement in the QoL, it is important to incorporate the patient’s perspective in treatment guidelines.

This study seeks to measure the degree of agglomeration of educational quality in Colombia, based on the non-socialization of the population that exhibits low educational quality, with the population that exhibits high educational quality, and thus determine how such agglomeration affects the phenomenon of academic segregation. To this end, we perform a spatial analysis of the educational quality in Colombia and of variables that may influence to the phenomenon of educational agglomeration. The level of agglomeration in educational quality in Colombia is demonstrated by the calculation of the Moran’s Index, in which a result of 0.62 was obtained. High educational quality is concentrated in the Andean region, while low educational quality is agglomerated in the periphery of the country, in areas such as the Pacific region. A spatial regression model was carried out to measure the dependence of municipalities on their neighbors, and to determine the main socio-economic factors affecting the phenomenon of educational agglomeration in Colombia, finding that living conditions, unsatisfied basic needs and fiscal transparency have all an impact on the educational quality of the municipalities. It is also found that the number of homicides in the municipalities does not seem to have a significant relationship with education.

The objective of this paper is to assess the potential for potable water savings due to rainwater use in a precast concrete factory in southern Brazil. The economic feasibility and the rainwater quality were also assessed. The current water consumption, future water demand and rainwater demand in the factory were estimated. The future demand considered was two times higher than the current water consumption since there are plans to increase the production. Three scenarios were then simulated using the computer programme Netuno. The ideal rainwater tank capacity, the potential for potable water savings and the economic feasibility analysis for each scenario were estimated. Samples of rainwater were collected in the factory and tested for quality for manufacturing precast concrete. For a rainwater tank capacity equal to 25,000 litres, the potential for potable water savings for the first scenario was 55.4%, but the first scenario was considered economically unfeasible. For the same tank capacity, the second and third scenarios presented viable results regarding potable water savings and payback. As for the rainwater quality, it was proven to be adequate for manufacturing precast concrete. The main conclusion is that rainwater can be used to manufacture precast concrete in the factory studied herein.

This purpose of the study presented in this article is to comparing different service quality measurements between Kano and TRIZ that plays the critical roles in the catering industrial. Data collected from a DINESERV questionnaire comprises service-quality standards to increase customer satisfaction of mobile dining car. Finally, the TRIZ is standardized measure designed to improve the idealization of strategy for selecting the most appropriate service quality model. In addition, the preferences of more than one decision maker are internally aggregated into the TOPSIS procedure. All these things provide several important theoretical and practical implications for developing a successful mobile catering app.

The purposes of this study are to introduce the concept of Service Quality (SQ) in E-Supply Chain Management (E-SCM) and its impact on increasing Customer Satisfaction (CS) and provide insightful enhancements to the literature. In addition, the paper also examines the influence of SQ of E-SCM on CS in online shopping. After a comprehensive literature review, four key factors for measuring the E-Supply Chain (Process Control, Interaction with Supplier, Management Support, and Focus on Customers), four key factors for measuring CS (Informing Customers, Attention to Customers’ Needs, Staff Performance Accuracy, and Easy Access to Services), and four factors for measuring the quality of identification services (Assurance, Accountability, Tangibility and Reliability) were selected. The proposed conceptual model was then presented. This model was validated by data collected through a survey of 150 respondents in order to identify customer satisfaction, including that of customers of online websites in Iran. The sample data was analyzed using SPSS21, after which the interrelationships between the model and factors were examined based on the Partial Least Square-Structural (PLS). Model fit indices were then calculated for the dataset. The proposed model was validated using factor analysis and structural equation modeling techniques. The results indicated that E-SCM has a direct impact on CS. The effect of SQ was also confirmed. A positive and significant relationship was identified between E-SCM and CS, E-SCM and SQ, as well as SQ and CS (P> 0.05). The first limitation was to convince respondents to cooperate with the researchers. The second one was the lack of research-related background due to the subject being relatively new. This study, to the best of the authors’ knowledge, is the first empirical analysis on the CS assessment of SQ of E-Supply Chain in online shopping. This important link to online shopping has rarely been explored. It is expected that by filling this gap, this study will help in strengthening online shopping, which needs a change in the marketing area.

This study investigates the characteristics of formaldehyde (HCHO) concentration and its reduction in newly constructed apartment buildings in Dubai. It addresses the significant health risks of high HCHO levels due to poor ventilation and extensive use of VOC-emitting materials. The research explores the effectiveness of various mitigation strategies, including air purifiers, photocatalyst applications, and window ventilation, in the living room, master bedroom (MBR), Room 1, and Room 2. HCHO concentrations were measured under different conditions: sealed windows, operation of an air purifier with a VOCs filter, and the application of a photocatalyst. The study followed a quantitative approach, recording real-time HCHO levels over 24 hours. Results indicated that sealing windows led to HCHO concentrations surpassing the domestic standard of 0.1 ppm, with the MBR recording the highest concentration at 0.73 ppm. The air purifier showed minimal impact within the first 8 hours but achieved an 18% reduction after 24 hours of operation. Applying a photocatalyst to room surfaces resulted in a 50% reduction in HCHO levels. Ventilation through window openings significantly improved air exchange rates, with the air exchange per hour (ACH) increasing proportionally with window opening size. Smaller rooms with larger window-to-volume ratios, such as Room 1 and Room 2, maintained HCHO concentrations below the WHO standard of 0.1 ppm with partial window openings. The study concludes that window ventilation is the most effective strategy for reducing HCHO concentrations, highlighting the importance of integrating comprehensive ventilation designs in modern residential buildings to ensure healthier indoor environments in Dubai.

Despite Vitamin B12's recognized importance for the nervous system, there's still a lack of research on the association between Vitamin B12 and sleep, especially in primary care settings. We assessed Vitamin B12 levels in adult primary health care users and investigated correlations with sleep quality, insomnia and sleepiness. In this cross-sectional study, 512 consecutive participants were included. Information regarding anthropometrics, socio-demographics, and medical history was obtained. The Epworth Sleepiness Scale (ESS), Athens Insomnia Scale (AIS), and Pittsburg Sleep Quality Index (PSQI) were used to quantify excessive daytime sleepiness (EDS), insomnia symptoms, and sleep quality, respectively. Median Vitamin B12 was 342 (266, 446) pg/mL. After adjustments, Vitamin B12 levels&lt;342 pg/mL showed significant associations with insomnia symptoms [OR (95% CI) 2.434 (1.331–4.452), p=0.004], especially in elderly, non-obese and female participants, with EDS only in obese participants [OR (95% CI) 3.996, (1.006-15.876), p=0.039]. Nonetheless, there was no significant association between B12 levels and poor sleep quality (OR 1.416, 95% CI 0.678-2.958, p=0.354). In conclusion, our results show that lower Vitamin B12 was associated with insomnia symptoms and sleepiness in specific groups of participants. However, further research with objective measurements of sleep is crucial to assess the relationship between sleep and Vitamin B12.

1) Background: Patients with neurological disorders are particularly at risk of falling and requiret functional rehabilitation. HUBER® is a motorised rotating platform that allows simultaneous work on balance, stability and strength with continuous adaptation and immediate feedback. This study aimed to measure the impact of rehabilitation with the HUBER® on the physical performance and quality of life of patients with neurological diseases requiring functional rehabilitation. 2) Methods: 32 subjects were enrolled in CHU Liège CNRF and randomly divided into 2 groups. The first group received classical rehabilitation combined with two training sessions per week on the HUBER® for 8 weeks. The second group received their usual treatment. This randomized control trial has been registered on clinicaltrials.gov under the number NCT04687293. Physical performance and quality of life were evaluated at different time. 3) Results: There was no significant difference between the 2 groups after enrolment. In terms of physical performance, an improvement in SPPB chair stand test (p=0.021) and total SPPB (p=0.003) was observed in the HUBER® group. In terms of quality of life, a higher improvement was observed overall in the HUBER® group (p&lt;0.05 between groups). 4) Conclusion: The HUBER® showed promising results in functional rehabilitation of patients with neurological pathologies, as a complement to classical rehabilitation management by physiotherapy.

Background: Cancer-related cognitive impairment (CRCI) is one of the most serious side effects of cancer that negatively impact the quality of life of cancer patients and survivors. There is evidence of CRCI in Hodgkin lymphoma patients (HL); however, there is a lack of studies examining the presence of cognitive deficits before starting any treatment in HL patients. Methods: Forty patients (N=40) newly diagnosed with HL (with no previous cancer diagnoses) and 40 healthy controls (N=40) matched for age, sex, education, and premorbid intellect completed the neuropsychological battery and subjective and objective measures of affective distress and quality of life. Results: The results showed impairment in three out of six cognitive domains: verbal memory and learning, speed of processing/ psychomotor speed, and abstraction/executive functions in the HL patients before the initiation of any treatment. Speed of processing/psychomotor speed domain negatively correlated with depression. Conclusion: Impairment in verbal memory and learning and abstraction/executive functions domains in HL patients seems to occur before the initiation of treatment independently of anxiety, depression, or physical symptoms. This suggests that HL itself may cause cognitive deficits in these cognitive domains. However, the underlying causes of CRCI still remain unclear.

Health related quality of life’s (HRQoL) different domains of functioning can serve as a good prognosticator of later life’s outcomes for children and adolescents. Understanding associated factors is crucial for promoting better health and life satisfaction. This study aimed to investigate the impact of socio-economic status (SES), physical activity (PA) and cardio-fitness on the Health-Related Quality of Life (HRQoL) in 224 Italian early adolescents attending secondary school in the Emilia-Romagna region located in northern Italy. The present cross-sectional study included measures of SES, demographic factors, cardio-fitness measures and self-reported PA levels. In a multivariate model, younger students and females reported higher HRQoL (β=-0.139, P<.05, 95% CI: -0.254 – -0.023 and β=0.142, P<.05, 95% CI: 0.011 – 0.273 respectively). Having both parents employed and having higher familiar educational status resulted in higher HRQoL. Greater engagement in routine PA was positively associated with HRQoL (β=0.429, P<.001, 95% CI: 0.304 – 0.554). Endurance (speed) was positively associated with HRQoL (β=0.221, P<.01, 95% CI: 0.087 – 0.355) and students with longer times on the shuttle run reported less HRQoL (β=-0.207, P<.01, 95% CI: -0.337 – -0.077). Findings reinforced the importance of promoting regular PA among students and addressing SES disparities to improve HRQoL. The study suggests a focus on expanding research measures and evaluating targeted PA interventions for a more comprehensive understanding of children’s well-being. These findings highlight the crucial roles of demographic, PA and cardio-fitness measures in child’s HRQoL, thus providing relevant information for stakeholders who work in the education, public health, and health policy sectors.

Wood quality has been an ongoing concern for specialists, which has become increasingly important in the current context, where the demand for wood is increasing and forest fires are more frequent and violent. The article aims to evaluate the quality of wood in trees affected by fires and the negative impact of these phenomena on the speed of wood degradation, as a result of the weakening of the trees due to the action of disturbing factors. Investigations were carried out using modern techniques on the beech trees (Fagus sylvatica L.) remaining in an area affected by a litter fire in 2017. Measurements were taken were made with the Arbotom Rinntech sound tomograph, the IML F-500 Resi resistograph and the Pressler core sampler to observe the quality of the wood inside the trunk. It was found that all the trees are in various stages of decaying the tomograms being able to highlight the severity of the defects only in the case of the total destruction of the wood structure as a result of the action of xylophages fungi, whose harmful influence is more pronounced when the injuries sustained by the trees from the fire were greater. Although the trees tried to close the fire wounds through their own defense mechanisms, the destructive action of the fungi intensified with the time.After the forest fires, for quickly and clear results regarding the internal quality of the wood could be used the resistograph. For valuable trees could be used the tomograph, but the measurements have to be taken only by qualified operators.