Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

Long-range interactions are relevant for a large variety of quantum systems in quantum optics and condensed matter physics. In particular, the control of quantum-optical platforms promises to gain deep insights in quantum-critical properties induced by the long-range nature of interactions. From a theoretical perspective, long-range interactions are notoriously complicated to treat. Here, we give an overview of recent advancements to investigate quantum magnets with long-range interactions focusing on two techniques based on Monte Carlo integration. First, the method of perturbative continuous unitary transformations where classical Monte Carlo integration is applied within the embedding scheme of white graphs. This linked-cluster expansion allows to extract high-order series expansions of energies and observables in the thermodynamic limit. Second, stochastic series expansion quantum Monte Carlo which enables calculations on large finite systems. Finite-size scaling can then be used to determine physical properties of the infinite system. In recent years, both techniques have been applied successfully to one- and two-dimensional quantum magnets involving long-range Ising, XY, and Heisenberg interactions on various bipartite and non-bipartite lattices. Here, we summarise the obtained quantum-critical properties including critical exponents for all these systems in a coherent way. Further, we review how long-range interactions are used to study quantum phase transitions above the upper critical dimension and the scaling techniques to extract these quantum critical properties from the numerical calculations.

Statistical modeling of lifetime data plays an essential role in a wide range of practical fields, such as health and engineering. There have been a lot of studies done to develop statistical models that can better describe health data than traditional models. For the first time, we pioneer a novel family of continuous probability distributions called the generalized odd beta prime generalized (GOBP-G) family of distributions. The cumulative distribution and probability density functions of the new family are presented. A new generalization of the Weibull distribution called "generalized odd beta prime-Weibull" (GOBPW) is proposed using the pioneered GOBP-G family. The mixture representations of the new distribution are defined and derived. Some formal statistical properties of the GOBPW distribution, such as the moments, moment generating function, incomplete moments, information generating function, entropies, stress-strength function, quantile function, and order statistics, are derived. The estimation of the parameters of the proposed distribution is evaluated using the maximum likelihood estimation approach. Different cancer disease data sets, such as the bladder, head and neck, acute bone, and blood cancers, are used to illustrate the applicability and usefulness of the new model and were compared using several statistical accuracy measures with that of well-established extended Weibull distributions, which are the beta modified Weibull distribution, Kumaraswamy modified Weibull distribution, gamma generalized modified Weibull distribution, gamma log-logistic Weibull distribution, and beta log-logistic Weibull distribution. The results show that the proposed model gives better results than the competitive models. This study could guide the relevant stakeholders in choosing a suitable statistical model for the health data instead of relying on traditional models to enhance decision-making.

The application of the sensors optical fiber in the areas of scientific instrumentation and industrial instrumentation is very attractive due to its numerous advantages. In the industry of civil engineering for example, quasi-distributed sensors made with optical fiber are used for reliable strain and temperature measurements. Here, a quasi-distributed sensor in the frequency domain is discussed. The sensor consists of a series of low-finesse Fabry-Perot interferometers where each Fabry-Perot interferometer acts as a local sensor. Fabry-Perot interferometers are formed by pairs of identical low reflective Bragg gratings imprinted in a single mode fiber. All interferometer sensors have different cavity length, provoking the frequency-domain multiplexing. The optical signal represents the superposition of all interference patterns which can be decomposed using the Fourier transform. The frequency spectrum is analyzed and sensor´s properties were defined. Following, a quasi-distributed sensor was numerically simulated. Our sensor simulation considers sensor properties, signal processing, noise system and instrumentation. The numerical results show the behavior of resolution vs. signal-to-noise ratio. From our results, the Fabry-Perot sensor has high resolution and low resolutions. Both resolutions are conceivable because the FDPA algorithm elaborates two evaluations of Bragg wavelength shift

The increasing demand for agricultural automation within the precision agriculture sector necessitates the development of advanced robotic systems to enhance efficiency in fruit harvesting. This study presents the Computer-Aided Design (CAD) and modeling of a 4-degree-of-freedom (DOF) robotic arm specifically designed for automated fruit harvesting applications. Utilizing Fusion 360 software, a comprehensive model has been created, encompassing material selection, stress analysis, and motion simulations to verify both the functionality and durability of the robotic system. Design methodologies are articulated, alongside simulation tests that evaluate the arm’s operational performance. Proposed enhancements aim to optimize harvesting efficiency while minimizing potential damage to crops. The robotic arm is equipped with an adaptive gripper, engineered to adjust to various fruit sizes, ensuring delicate and precise manipulation during the harvesting process. This work establishes a robust foundation for the advancement of robotic systems in agricultural contexts, contributing to improved productivity and sustainability in fruit harvesting operations.

This paper investigates the integration of artificial intelligence (AI) and robotics in healthcare, highlighting the potential of autonomous humanoid robots to replicate compassionate care while centering on ethical and safety concerns related to reliability, quality, and empathy. It reviews the benefits, challenges, and ethical considerations of deploying humanoid robots in care settings, including user acceptance and technological limitations, and questions their ability to genuinely simulate compassion. Through multisensory simulations of human-robot interactions (HRIs) using agent-based modeling, the study reveals complex dynamics among patients, robots, and healthcare systems, suggesting that advanced robot designs can enhance personalized sensing with quantum and neuromorphic information processing. Additionally, it analyzes the philosophical implications of robotic nursing care, advocating for a posthumanist perspective that recognizes nonhuman caring agencies, and concludes with recommendations for future research to improve communication and humanize the capabilities of robots in caregiving.

This paper proposes a metaphysical framework for distinguishing between human and machine intelligence. It posits two identical deterministic worlds -- one comprising a human agent and the other a machine agent. These agents exhibit different information processing mechanisms despite their apparent sameness in a causal sense. Providing a conceptual modeling of their difference, this paper resolves what it calls “the vantage point problem” – namely, how to justify an omniscient perspective through which a determinist asserts determinism from within the supposedly deterministic universe.

The discrete element method (DEM) coupled with computational dynamics (CFD) has been considered one of the most sensitive ways of studying fluidized beds. This paper presents gas-solid fluidized bed simulations by use of CFD-DEM. The two-phase interaction is calculated in a way of decoupling. Within the effective neighborhood of the particles, the kernel approximation method is used to calculate the local porosity, thereby calculating the drag force on the particles. At the grid scale, the momentum exchange coefficient is calculated using a two fluid model based method, thereby calculating the source term of the phase interaction in the fluid control equation. The simulated form, size and motion process of the big bubble are all consistent with experimental observations. The simulated solid volume fraction and relative pressure averaged in a horizontal plane at 45 mm above the bottom are in reasonable agreement with the experimental data. The fluctuation of the simulated bed height over time is similar to the experimental measurement results. The reproduction of these qualitative and quantitative results indicates that the proposed method effectively improves simulation performance and accuracy.

A case of low level windshear at Beijing Daxing International Airport is studied in the present pa-per. It is related to the synoptic scale/mesoscale changes of the airflow pattern over northern China. The shear was captured well by the Doppler LIDAR at the airport and timely alerts had been issued. This study considers the technical feasibility of forecasting the shear feature using a high resolution numerical weather prediction model with a lead time of several hours. It turns out that the shear feature could be forecast well, and is generally consistent with the actual observations. However, there are still discrepancies between reality and the simulation, such as the strength of the shear and persistency of the feature. More cases of windshear at Daxing airport would be studied in the fu-ture in order to understand the nature of windshear over there.

The genus Flavivirus includes 53 members and poses a big threat to human health among worldwide. Diseases caused by flavivirus infections can be broadly classified into hemorrhagic diseases (Dengue, Yellow fever, etc) and neurological diseases (West Nile disease, Zika disease, etc). Many flaviviruses still lack specific treatments and effective vaccines. In this context, it becomes particularly important to thoroughly characterize the pathogenesis of flavivirus infection and develop animal models. Therefore, animal models that can accurately simulate human diseases are essential for evaluating the effectiveness of therapeutic drugs and preventive vaccines. In this paper, we provide a comprehensive review of the currently available animal models that support flavivirus infection and exhibit clinical manifestations related to flavivirus infection. Additionally, we discuss the strengths and limitations of each animal model, aiming to enhance researchers understanding of the use of animal models in flavivirus research. This insight is intended to facilitate further studies into the pathogenesis of flavivirus, as well as the development of antiviral agents and vaccines.

A systematic investigation of the dynamic clustering behavior of active particles under confinement, including the effects of both particle density and active driving force is presented based on a hybrid coarse-grained molecular dynamics simulation. First, a series of scaling laws were derived with power relationships for the dynamic clustering time as a function of both particle density and active driving force. Notably, the average number of clusters N ̅ assembled from active particles in the simulation system exhibits a scaling relationship with clustering time t described by N ̅∝t^(-m). Simultaneously, the scaling behavior of the average cluster size S ̅ is characterized by S ̅∝t^m. Our findings reveals the presence of up to four distinct dynamic regions concerning clustering over time, with transitions contingent upon the particle density within the system. Furthermore, as the active driving force increases, the aggregation behavior also accelerates, while an increase in density of active particles induce alterations in the dynamic procession of the system.

Fatigue fractures in materials are the main cause of approximately 80% of all material failures, and it is believed that such failures can be predicted and mathematically calculated in a reliable manner. It is possible to establish prediction modalities in cases of fatigue fracture, according to three fundamental variables in fatigue, such as volume, number of fracture cycles, as well as applied stress, with the integration of Weibull constants (length characteristic). This investigation was carried out mechanical fatigue tests on specimens smaller than 4 mm2 in section of different industrial materials for their subsequent analysis through precision computed tomography in search of microfractures. The measurement of these microfractures, along with their metrics and classifications, was recorded. A convolutional neural network trained with deep learning was used to achieve the detection of microfractures in image processing. The detection of microfractures in images with 480x854 or 960x960 pixels is the primary objective of this network, and its accuracy is above 95%. Images that have microfractures and those that do not are classified by the network. Subsequently, by means of image processing, the microfracture is isolated. Finally, the images that do contain this feature are interpreted by image processing to obtain their area, perimeter, characteristic length, circularity, orientation, and type microfracture metrics. All values will be obtained in pixels and converted to metric units (μm) through a conversion factor based on image resolution.

The article presents the method of identification of dynamic models for different flight states of a rotary-wing UAV. Experimental flights were conducted to obtain data necessary for the identification process. Such models can later be implemented in simulations to represent the behavior of real-life objects. Simulation of UAV swarms is the first stage of developing a swarm system, where prototyping with physical models is problematic. Therefore, obtaining accurate models is crucial for the simulation process to be reliable. Also, verification of obtained models was performed to make sure that they were identified correctly. In particular, the presented method was proven effective and successfully used in some applications.

In this study, the Bohler K 190 steel was used. The steel was manufactured by the powder metallurgy (PM) process. The boronizing process was carried out in the range of 1173 to 1323 K, for 1-10 h. The samples were boronized in solid medium, called the Durborid powder mixture. For the microstructural observations, the scanning electron microscopy was utilized for determining the morphology of interfaces and measuring the layers’ thicknesses. The phase composition of boride layers was also determined with X-ray diffraction analysis. To investigate the redistribution of chemical elements redistribution during the boronizing process, the EDS mapping and EDS point analysis were used. The boride layers were constituted by FeB and Fe2B phases except for 1173 K for 1 h. The values of Vickers microhardness of Fe2B, FeB and transition zone were estimated. Finally, to assess the boron activation energies in FeB and Fe2B, the so-called integral method was applied and the results in terms of activation energies were confronted with the literature data.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

The current theories of consciousness do not address the two major problems:What is the solution to the hard problem of consciousness or What is the experience of self-existence? and How is conscious perception computed? We address these questions using our hypothesized theory:The Self Simulation theory and propose a model of computation of consciousness.The components of the model are an interconnected network of auxiliary processors or Auxiliary Neural Networks(AN) which receives input from the external sensory modalities,computes a representation of the information and relays it to the NCC(Neural Correlates of Consciousness), the NCC – a processing unit which can be neuro anatomically distributed in location but computationally connected to each other and to the Auxiliary Networks,and a working memory which the NCC references for further computation of information.Computation of conscious perception is achieved via the decoding of the content of the memory by the NCC.The self simulation theory accounts not only for the various phenomenal experiences but also experimentation paradigms conducted in the past.

Although train simulation research is vast, most available network simulators do not track the instantaneous movements and interactions of multiple trains for the computation of energy/fuel consumption. In this paper, we introduce the NeTrainSim simulator for heavy long-haul freight trains on a network of multiple intersecting tracks. Trains are modeled as a series of moving mass points (each car/locomotive is modeled as a point mass) while ensuring safe following distances between them. The simulator considers the motion of the train as a whole and neglects the relative movements between the train cars/locomotives. Furthermore, the powers of the different locomotives are transferred to the first locomotive as such a simplification result in a reduced simulation time without impacting the accuracy of energy consumption estimates. While the different tractive forces are combined, the resistive forces are calculated at their corresponding locations. The output files of the simulator contain pertaining information to the train trajectories and the instantaneous energy consumption levels. A summary file is also provided with the total energy consumed for the full trip and the entire network of trains. Two case studies are conducted to demonstrate the performance of the simulator. The first case study validates the model by comparing the output of NeTrainSim to empirical trajectory data using a basic single-train network. The results confirm that the simulated trajectory is precise enough to estimate the electric energy consumption of the train. The second case study demonstrates the train-following model considering six trains following each other. The results showcase the model’s ability in relation to maintaining safe-following distances between successive trains. Finally, the NeTrainSim is demonstrated to be scalable with computational times of O(n) for less than 50 trains (n) and O(n²) for higher number of trains.

The oncogenic potential of high-risk HPVs is focused on producing the E6 and E7 oncoproteins responsible for disrupting the control of the cell cycle. Epidemiological studies propose the presence of the N29S and H51N variants of the HPV16 E7 protein as a significant association with cervical cancer. It has been suggested that changes in the amino acid sequence of E7 variants may affect the oncoprotein 3D structure; however, this remains unknown. Analysis of the structural differences of the HPV16 E7 protein and its variants (N29S and H51N) was performed through homology modeling and structural refinement by molecular dynamics simulation. We propose for the first time a 3D structure of the E7 reference protein and two of its variants (N29S and H51N) and conclude that the mutations induced by the variants in N29S and H51N have a significant influence on the 3D structure of the E7 protein of HPV16, which could be related to the oncogenic capacity of this protein.

Susceptible, infective, recovered, and hospitalized/isolated individuals are placed on the cells of a nxn square lattice, where each cell is occupied by a single individual or is vacant. At discrete time units (typically one day each) all susceptibles and infectives execute a random movement and when a coincidence of the two types occurs the susceptible is converted to infective status according to some probability. Infectives are labelled by the number of days since originally infected. At each time increment the age label of the infectives is increased by one unit. When the label reaches a number like 15 or 20 days the susceptibles recover with some probability or become isolated/hospitalized. Upon reaching some age the latter types either recover or die. Probabilities for the movements and conversions from one status to another are implemented by random numbergeneration. Simulations were carried out to investigate the effect of several probability and age parameters, the size of population (proportional to nxn) and density (related to fraction of occupied cells), and the size of the movements. Mid-term gradual conversion of susceptibles to isolated was explored as intervention policy.

The novel Coronavirus (COVID-19) is spreading and has caused a large-scale infection in China since December 2019. Thefirst infected person was declared on March 18, 2020 in Djibouti. This has led to a signicant impact on the lives and economy in Djibouti and other countries. In this study, we propose a double compartment stochastic model which describes the evolution of the infection rate and the evolution of the number of infected in the period from May 20 to June 23, 2020. We will also propose the evolution of people infected in two states, recovered and deceased.

Molecular dynamics simulations were carried out to investigate the atomic structure of a model Cu64Zr36 bulk metallic glass (BMG). It is found that the amount of icosahedral content of the system is significantly increased in a well relaxed structure. While we considered four connection types of vertex-, edge-, face-, and volume-sharing, the huge cluster in the relaxed samples mainly involve volume-type connection and exhibits a remarkable athermal plasticity that great stiffness and great yield strength compared to the as-quenched samples. In addition, the bond-angle distribution of annealed sample shows sharp peaks at specific bond angles which is an evidence of crystallized Laves-phase formed by icosahedral atoms, however the peaks are to be broaden after loading, which indicates decreasing amount of icosahedral content and their shape distortion. These results suggest that icosahedral content in a bulk metallic glasses plays a key role to determine the mechanical properties such as rigidity and maximum stress carrying capacity.

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

Network Simulators is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. Many problems can be solved by using network simulators such as NS-3. With this in mind, the aim of this article is to introduce new NS-3 users through detailed information. It is sometimes difficult to handle by new users the traditional manuals developed by NS-3 project official website. In this article, NS-3 for communication network and Eclipse Integrated Development Environment (IDE) for powerful programming language are integrated step-by-step, explaining the main features of these open source software packages and concluding with an example simulation. Our effort is to make it easy for a beginner to be part of the NS-3 research community and to maintain an open environment of knowledge.

In this report we have discussed the important role of molecular modeling, especially the use of the molecular dynamics method, in investigating transport processes in nanoporous materials such as membranes. With the availability of high performance computers, molecular modeling can now be used to study rather complex systems at a fraction of the cost or time requirements of experimental studies. Molecular modeling techniques have the advantage of being able to access spatial and temporal resolution which are difficult to reach in experimental studies. For example, sub-Angstrom level spatial resolution is very accessible as is sub-femtosecond temporal resolution. Due to these advantages, simulation can play two important roles: Firstly because of the increased spatial and temporal resolution, it can help understand phenomena not well understood. As an example, we discuss the study of reverse osmosis processes. Before simulations were used it was thought the separation of water from salt was purely a coulombic phenomenon. However, by applying molecular simulation techniques, it was clearly demonstrated that the solvation of ions made the separation in effect a steric separation and it was the flux which was strongly affected by the coulombic interactions between water and the membrane surface. Additionally, because of their relatively low cost and quick turnaround (by using multiple processor systems now increasingly available) simulations can be a useful screening tool to identify membranes for a potential application. To this end, we have described our studies in determining the most suitable zeolite membrane for redox flow battery applications. As computing facilities become more widely available and new computational methods are developed, we believe molecular modeling will become a key tool in the study of transport processes in nanoporous materials.

MCrAlX (M: Ni or Co or both, X: minor elements) coatings have been widely used to protect hot components in gas turbines against oxidation and hot corrosion at high temperatures. Understanding the influence of the X-elements on oxidation behaviour is important in the design of durable MCrAlX coatings. In this study, NiCoCrAlX coatings doped with Y+Ru and Ce, respectively, were deposited on Inconel-792 substrate by HVOF. The samples were subjected to isothermal oxidation test in laboratory air at 9000, 1000, 1100 ºC and cyclic oxidation test between 100 ºC and 1100 ºC with 1 hour dwell time at 1100 ºC. It was observed that the coating with Ce shows a much higher oxidation rate than the coating with Y+Ru under both isothermal and cyclic oxidation tests. Besides, β-depletion due to interdiffusion between coating and substrate was significantly lower with Ru addition. Simulations results using both a moving phase boundary model and an established oxidation-diffusion model show that Ru stabilize β grains which reduces β-depletion of coating due to substrate interdiffusion. This paper presents a comprehensive study of the influence of Ce and Ru on oxidation behaviour including investigation of the microstructure evolution influenced by oxidation time at coating surface and coating-substrate interface combining experiment and simulation results.

In the present paper, laminar forced convection nanofluid flows in a uniformly heated horizontal tube were revisited by direct numerical simulations. Single and two-phase models were employed with constant and temperature-dependent properties. Comparisons with experimental data showed that the mixture model performs better than the single-phase model in the all cases studied. Temperature-dependent fluid properties also resulted in a better prediction of the thermal field. A particular attention was paid to the grid arrangement. The two-phase model was used then confidently to investigate the influence of the nanoparticle size on the heat and fluid flow with a particular emphasis on the sedimentation process. Four nanoparticle diameters were considered: 10, 42, 100 and 200 nm for both copper-water and alumina/water nanofluids. For the largest diameter dnp = 200 nm, the Cu nanoparticles were more sedimented by around 80 %, while the Al₂O₃ nanoparticles sedimented only by 2.5 %. Besides, it was found that increasing the Reynolds number improved the heat transfer rate, while it decreased the friction factor allowing the nanoparticles to stay more dispersed in the base fluid. The effect of nanoparticle type on the heat transfer coefficient was also investigated for six different water-based nanofluids. Results showed that the Cu-water nanofluid achieved the highest heat transfer coefficient, followed by C, Al₂O₃, CuO, TiO₂, and SiO₂, respectively. All results were presented and discussed for four different values of the concentration in nanoparticles, namely φ = 0, 0.6, 1 and 1.6%. Empirical correlations for the friction coefficient and the average Nusselt number were also provided summarizing all the presented results.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

In order to be able to face competition, thriving corporations have to be compelled to maintain an awfully smart relationship with their existing customers and additionally to be able to anticipate their future wants. Thus, corporations do not target customers as teams, however they’re attempting to focus on them as individuals. However, to be able to use this information, corporations have to be compelled to use promoting automation tools. Marketing Automation was an idea first introduced in 2001 by John D.C. Little in his presentation at the 5th Invitational Choice Symposium UC Berkeley 2001. This survey paper assesses prominent research on Marketing Automation and suggests how it can be modified to adapt to the current marketing scenario.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Conventional X-ray therapy (XRT) is commonly applied to suppress cancerous tumors, however it often inflicts collateral damage to nearby healthy tissue. In order to provide a better conformity of the dose distribution in the irradiated tumor, proton therapy (PT) is increasingly being used to treat solid tumors. Furthermore, radiosensitization with gold nanoparticles (GNPs) has been extensively studied to increase the therapeutic ratio. The mechanism of radiosensitization is assumed to be connected with an enhancement of the absorbed dose due to huge photoelectric cross-sections with gold. Nevertheless, numerous theoretical studies mostly based on Monte Carlo (MC) simulations did not provide consistent and thorough picture of dose enhancement and, therefore, radiosensitization effect. Radiosensitization by nanoparticles in PT is even less studied than in XRT. Therefore, we investigate physics picture of GNP-enhanced RT using MC simulation with Geant4 equipped with the most recent physics models, taking into account a wide range of physics processes relevant for realistic PT and XRT. Namely, we measured dose enhancement factors in the vicinity of GNP with diameters ranging from 10 nm to 80 nm. The dose enhancement in the vicinity of GNP reaches high values for XRT, while it is very modest for PT. The macroscopic dose enhancement factors for realistic therapeutic GNP concentrations are rather low for all RT scenarios, therefore other physicochemical and biological mechanisms should be additionally invoked for an explanation of the radiosensitization effect observed in many experiments.

Building energy modelling tools play a crucial role in quantifying and comprehending the energy performance of buildings. These tools demand substantial amounts of data, which can be challenging to acquire and are often associated with significant uncertainties. The incorporation of Sensitivity Analysis represents a relevant step towards developing reliable models, as it identifies the most critical parameters that require a meticulous characterization. In this study, a Sensitivity Analysis based on Morris method was conducted to assess the relevance of 14 input parameters affecting thermal loads across four dwelling typologies modelled in EnergyPlus. Different number of Morris trajectories and levels were considered to analyse the impact of the user-defined values of r and p when employing Morris method. Convergence was achieved from r=200 and p=12, which are higher than the typically employed values (r=10 and p=4). Setpoint temperatures, orientation, roof solar absorptivity and roof conductance rank among the most relevant parameters affecting thermal loads, however variations are observed for the four case studies.

Choosing a career path is an important decision in a person’s life and forms the basis for their future direction. It impacts the future career and influences financial stability as well as the person’s well-being. Many people struggle to find out what they are interested in and talented in, making it difficult to choose a fitting career path. Therefore, the decision-making process requires careful consideration, self-reflection, and exploring numerous options. While virtual environments provide an effective way to explore different experiences, virtual reality (VR) offers users immersive interactions with simulated 3D environments. This allows the realistic exploration of different job fields in a virtual environment without being physically present. VR 360-degree videos have been shown to significantly increase job interest among students. The ability to review and refine performance makes VR an ideal tool for career skill development as well as career guidance. In this paper, we present a tool that offers young people virtual career guidance through an immersive VR experience. The study investigates the extent to which performing occupational tasks in a virtual environment influences the career perceptions of young adults and whether it enhances their understanding of professions. In total, 23 teenagers and 8 application experts were involved to assess the teenager’s expectations and the potential of the career guidance tool.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

As an active device, air source heat pumps (ASHP) are widely used for heating and cooling in buildings. However, in cold regions, their efficiency decreases, and frost formation becomes a significant issue during winter. This paper proposes a new scheme that couples air source heat pumps with passive heating. By using software simulations and mathematical models, the new scheme is compared to traditional ASHP systems to analyze its heating performance in rural homes during winter in China’s cold regions. According to the simulation and calculation analysis, on the coldest day of winter, the coupling scheme can provide approximately 99.41kWh of heat to the interior, surpassing the 86.67kWh required to maintain an indoor temperature of 20℃. The system’s power consumption is 36.96 kWh, which is 66.88% lower than that of traditional heat pump heating. The study shows that a coupled system of air source heat pumps and passive heating has better heating performance in cold regions. By incorporating phase change materials and heat storage media to address the shortage of solar energy at night, the system can meet the heating needs throughout the entire day.

The endeavor to decode the brain's intricate architecture and its multifaceted functions has propelled scientists into the domain of complex differential equations, aiming to construct a computational framework capable of representing its uncountable intricacies. This article delves into the sophisticated and daunting task of modeling the brain, a system of seemingly uncountable coupled differential equations, each symbolizing the vast array of interconnected neural pathways and processes. We discuss the current limitations of computational resources and the significant challenges faced in accurately capturing the non-linear, high-dimensional, and plastic nature of neural dynamics. Despite these challenges, we explore the progressive strides in computational neuroscience that lay the groundwork for partial models, offering insights into the brain's localized circuits and broader network interactions. These models serve as pivotal stepping stones towards a more comprehensive understanding, which is incrementally built upon by interdisciplinary approaches, leveraging advancements in neuroimaging, data analysis, and theoretical biology. Looking ahead, the article speculates on the potential paradigm shifts that could arise from breakthroughs in computational technology, such as quantum computing, that may one day enable the simulation of the brain in its entirety. The article ultimately paints a picture of cautious optimism, where each incremental discovery is a valuable piece of the grand puzzle, bringing us closer to the epochal goal of comprehensively modeling the human brain.

As technology advances, the field of electrical and computer engineering continuously demands the introduction of innovative new tools and methodologies to facilitate effective learning and comprehension of fundamental concepts. This research addresses an identified gap in technology-augmented education capabilities and researches the integration of Virtual Reality (VR) technology with real-time electronic circuit simulation to enable and enhance the visualization of non-observable concepts such as voltage distribution and current flow within these circuits. In this paper, we describe the development of our immersive educational platform, which makes understanding these abstract concepts intuitive and engaging. This research also involved the design and development of a VR-based circuit simulation environment. By leveraging VR’s immersive capabilities, our system enables users to physically interact with electronic components, observe the flow of electrical signals, and manipulate circuit parameters in real-time. Through this immersive experience, learners can gain a deeper understanding of fundamental electronic principles, transcending the limitations of traditional two-dimensional diagrams and equations. Furthermore, this research focuses on the implementation of advanced and novel visualization techniques within the VR environment for non-observable electrical and electromagnetic properties, providing users with a clearer and more intuitive understanding of electrical circuit concepts. Examples include color-coded pathways for current flow and dynamic voltage gradient visualization. Additionally, real-time data representation and graphical overlays are researched and integrated to offer users insights into the dynamic behavior of circuits, allowing for better analysis and troubleshooting.

Repetitive elements, often referred to as selfish genes, pose significant challenges to genome assembly and read mapping in bioinformatics. These elements can replicate within the genome without providing functional benefits to the host organism, leading to complexities in accurate genome analysis. This study presents a simulation-based approach to illustrate the impact of repetitive elements on read mapping accuracy. By comparing genome sequences with and without repetitive elements, we demonstrate how these selfish genes create ambiguities and errors in read alignment. The findings underscore the importance of developing advanced bioinformatics tools aligned with artificial intelligence to mitigate the effects of repetitive sequences and improve the reliability of genomic analyses.

While there are software tools available for assisting to conduct the Life Cycle Assessment (LCA), such as OpenLCA, these tools lack integration with process design, simulation and optimization software. As LCA has critical role in sustainable product design, it is presented in this work a platform called EMSO_OLCA, which integrates the LCA provided by OpenLCA into the Environment for Modeling, Simulation, and Optimization (EMSO). EMSO_OLCA incorporates a database of environmental impact assessment methodologies from OpenLCA and aligns to the principles of LCA outlined in ISO 14040 and ISO 14044. Validation tests were conducted to compare the results obtained by the LCA of sugarcane ethanol using OpenLCA and EMSO_OLCA, revealing a high level of agreement. The average relative error was 0.045%, indicating a negligible discrepancy between the tools. Besides, it took only 0.3 seconds for calculation, which is desirable for using with process systems engineering tools. A second case study was applied to a steam and bioelectricity production from the combustion of sugarcane bagasse and straw in a combined heat and power system. The results show the integration of LCA with simulation and sensitivity analysis tools, thus contributing for supporting sustainable decision-making processes. EMSO_OLCA bridges the gap between LCA and process engineering, enabling a holistic approach to sustainability, design and implementation of environmentally friendly solutions.

In general, during emergencies, healthcare is provided by tents and temporary structures that do not consider the environmental and social impact of the structure as a first term, in favor of swift response. The resultant construction intended as a temporary solution often persists long-term. This paper aims to analyze an alternative and innovative modular structure designed as a transitory solution in emergency and everyday life. In the first part of the paper, the conceptual framework, and the preliminary design for the new approach to basic non-conventional sanitary spaces are described, by investigating the benefits of a safe space as a generator space for care services and community. In the second part, the technological requirements of the system, its energy efficiency, and environmental impact are analyzed.

This study addresses the prevalent gap between formal and informal architectural methodologies in software engineering. Recognizing the potential of informal architecture artifacts in analytical processes, we introduce a groundbreaking methodology that efficiently transforms these informal components into structured formal models. This method facilitates a deeper understanding and utilization of informal diagrams and enhances analytical capabilities through graph analysis techniques. By leveraging user-friendly tools like Draw.io, the methodology democratizes the modeling process, making sophisticated architectural analyses accessible to a broader spectrum of professionals without requiring deep expertise in formal methods. The innovative aspects of this methodology lie in its ability to streamline the transformation process, significantly improving both the efficiency and effectiveness of model creation and analysis. These enhancements are demonstrated through a practical application involving a sample architecture diagram, where the resulting model is thoroughly analyzed using advanced graph analysis tools like Python's NetworkX library and Neo4j. This approach bridges the theoretical and practical divides in software architecture and sets a new standard for integrating informal artifacts into systematic engineering workflows. In addition, considerations for Artificial Intelligence developments are discussed.

Subgrid scale models for unresolved turbulent fluxes are investigated with a focus on combustion for space propulsion applications. An extension to the gradient model is proposed, introducing a dependency on the local burning regime. The dynamic behavior of the model's coefficients is investigated, and scaling laws are studied. The discussed models are validated using a DNS database of a high-pressure turbulent fuel-rich methane-oxygen diffusion flame. The operating point and turbulence characteristics are selected to resemble those of modern combustors for space propulsion applications to support the future usage of the devised model in this context.

The rapid integration of Information and Communication Technology (ICT) is transforming the traditional electrical grid into a {\em Smart Grid}. Smart grids enable two-way communication and improved monitoring and control between utilities and customers. However, due to its heterogeneous nature, public exposure, and weak security at low-powered devices, the Smart Grid has vulnerabilities to various malicious threats, adversaries, and cyber attacks, which may affect cost and service availability. Additionally, when the systems' confidentiality, integrity, or availability are compromised, the resulting fallout can threaten national security and have cascading effects on human lives. Given the extreme consequences of an attack, smart-grid technology must be thoroughly tested for correct operation and security {\em before} it is deployed. As a result, vulnerability testing of smart grids, not only for correctness but for security purposes, has been the subject of numerous studies by academics, government agencies, and private companies. This paper reviews the vulnerabilities associated with the smart grid and spotlights simulation as the vulnerability testing methodology conducted in recent pertinent research works. It also presents various security aspects of the smart grid, including grid applications, system and network infrastructure and components, cyber threats and attacks, simulation, and different mitigation techniques. Finally, we analyze the gaps in the current research works, focusing on simulation. We briefly present a real-time simulation testbed that mimics customer behaviour and integrates hardware in the loop to apply attack methods, analyze vulnerabilities and risk mitigation associated with the smart grid system, and propose future work to improve the current framework.

Daylighting has been widely adopted in recent years due to its potential to improve the indoor environment in terms of visual comfort and energy-saving. One of the energy-saving techniques for energy-efficient buildings is the integration of louver systems. Louvers are considered more efficient for providing daylight in the interior as compared to other daylighting systems. Here, this paper presents the design of a louver system for conducting energy simulations for lighting and cooling requirements in office spaces. The simulation results indicate that the use of louvers in different opening configurations can lead to energy savings, particularly in the lighting aspect. The louver system in office spaces with a 50% louver opening leads to 27.0% energy savings. Further, the results are presented for different louver openings to calculate the lighting and cooling energy savings. The overall performance of the system is better in terms of providing consistent daylight, which eventually improves energy saving.

Matrix asphalt material has poor road performance, which is improved by adding polymer modified agents. The original asphalt material experiment research has a certain limitation in that it cannot truly expose the mechanism and influence of modifiers on asphalt materials. To explore the gain effect of the modified agent on the asphalt material's road performance, the molecular dynamic simulation technology is used to explain its mechanism in the micro dimension. The three parameters of the free volume score, radial distribution function and average directional shift diffusion coefficient are analysed to improve the performance of the modifier on asphalt material, an exploration of the microdimension shows that the amount of SBS modifiers is 6% and the amount of rubber modified asphalt material is 22%. The improvement of materials is better than that of rubber modifiers.

Using metaheuristics, such as the Evolutionary Algorithm (EA), within control structures is a realistic approach for certain optimal control problems. Their role is often predicting the optimal control values over a prediction horizon using a process model (PM). The big computational effort sometimes causes problems. Our work addresses a new issue: whether a machine learning (ML) algorithm could “learn” the optimal behaviour of the couple (EA, PM). A positive answer is given by proposing datasets apprehending this couple's optimal behaviour and appropriate ML models. Following a design procedure, a number of closed-loop simulations will provide the sequences of optimal control and state values, which are collected and aggregated in a data structure. For each sampling period, datasets are extracted from the aggregated data. The ML algorithm experiencing these datasets will produce a set of regression functions. Replacing the EA predictor with the ML model, new simulations are carried out, proving that the state evolution is almost identical. The execution time decreases drastically because the PM’s numerical integrations are totally avoided. The performance index equals the best-known value. In different case studies, the ML models succeeded in capturing the optimal behaviour of the couple (EA, PM) and yielded efficient controllers.

Abstract: The population issue has been increasingly urgent in China in recent years. Fertility desire is an essential component of fertility research. Studies on fertility desire mainly contain two aspects: socio-economic structure and individual family[1]. The psychological structure of individuals in individual families is the primary factor of fertility desire. Based on the parasocial relationship theory, this study analyzed the changes in real behavioral intention achieved by players through the identification and attachment to avatars while constructing parasocial relationships[2]. The results indicate that character attachment can significantly enhance the variables of game concentration and player self-identity, actively mediates parasocial emotions and parasocial cognition, and ultimately increases fertility desire. As a theoretical contribution, this study provides a comprehensive interpretation of the psychology of Chinese players in a Simulation Game and explores the theoretical connections among role attachment, role identity, and parasocial relationships in virtual game players.

With an explosion of data in the nearly every domain, from physical and environmental sciences to econometrics and even social science, we have entered a golden era of time-domain data science. In addition to ever increasing data volumes and varieties of time-series, there's a plethora of techniques available to analyses them. Unsurprisingly, machine learning approaches are very popular. In environmental sciences (ranging from climate studies to space weather/solar physics), machine learning (ML )and deep learning (DL) approaches complement the traditional data assimilation approaches. In solar and astrophysics, multiwavelength time-series or lightcurves along with observations of other messengers like gravitational waves provide a treasure trove of time-domain data for ML/DL approaches for modeling and forecasting. In this regard, deep learning algorithms such as recurrent neural networks (RNNs) should prove extremely powerful for forecasting as it has in several other domains. Such methods agnostic of the physics can only predict transient flares that are represented in the original distribution trained on (eg. coloured noise fluctuations) and not special, isolated episodes (eg. a one-off outburst like a major coronal mass ejection) potentially distinguishing them. Therefore it is vital to test robustness of these techniques ; here we attempt to make a small contribution to this by exploring sensitivity of RNNs with some rudimentary experiments. We test the performance of a very successful class of RNNs, the Long Short Term Memory (LSTM) algorithms with simulated lightcurves. As an example, we focus on univariate forecasting of time-series (or lightcurves) characteristic certain variable astrophysical objects (eg. active galactic nuclei or AGN). Specifically, we explore the sensitivity of training and test losses to key parameters of the LSTM network and data characteristics namely gaps and complexity measured in terms of number of Fourier components. We find that typically, the performances of LSTMs are better for pink or flicker noise type sources. The key parameters on which performance is dependent are batch size for LSTM and the gap percentage of the lightcurves. While a batch size of $10-30$ seems optimal, the most optimal test and train losses are under $10 \%$ of missing data for both periodic and random gaps in pink noise. The performance is far worse for red noise. This compromises detectability of transients. Thus, we show that generative models (time-series simulations) are excellent guides for use of RNN-LSTMs in building forecasting systems

Plasmonics is the study of resonant oscillations of free electrons in metals caused by incident electromagnetic radiation. Surface plasmons can focus and steer light on the subwavelength scale. Apart from metals, plasmonic phenomena can be observed in soft matter systems such as electrolytes where resonant charge oscillations can be induced for ions in solution. Due to their larger mass, they are plasmon-active in a lower frequency regime and on a larger wavelength scale. Spatial confinement allows increasingly strong charge interactions and gives rise to nonlocality or spatial dispersion effects. These effects manifest as additional longitudinal propagation modes and are known to cause plasmonic broadening and resonance shifts in metal nanostructures. We derive and discuss the nonlocal optical response of ionic plasmons using a hydrodynamic, two-fluid model in a planar homogeneous three-layer system with electrolyte-dielectric interfaces. Studying such systems enables us to identify and understand plasmonic phenomena in biological and chemical systems.

This study rolls out a robust framework relevant for simulation studies through the Generalised Autoregressive Conditional Heteroscedasticity (GARCH) model using the rugarch package. The package is thoroughly investigated, and novel findings are identified for improved and effective simulations. The focus of the study is to provide necessary simulation steps for volatility estimation that involve "background (optional), defining the aim, research questions, method of implementation, and summarised conclusion". The method of implementation is a workflow that includes writing the code, setting the seed, setting the true parameters a priori, data generation process and performance assessment through meta-statistics. This novel, easy-to-understand steps are demonstrated on financial returns using illustrative Monte Carlo simulation with empirical verification. Among the findings, the study shows that regardless of the arrangement of the seed values, the efficiency and consistency of an estimator generally remain the same as the sample size increases. The study also derived a new and flexible true-parameter-recovery measure which can be used by researchers to determine the level of recovery of the true parameter by the MCS estimator. It is anticipated that the outcomes of this study will be broadly applicable in finance, with intuitive appeal in other areas, for volatility estimation.

Currently, there are different types of technology for the production of electricity that use various energy sources, this causes the establishment of generation centers that provide from a small amount to tens of megawatts of electrical energy. These centers are built to supply electricity to nearby loads through networks integrated into a large electrical system or in isolation with their electrical system. The technological evolution, the different energy sources, and the generation centers close to the consumers entail what has been called a distributed generation (DG), the DG carries with it aspects that need to be analyzed. In this paper, the impact of wind generation on the medium voltage energy distribution network is studied, it was determined that the addition to the distribution network of power by wind turbines less than the transmission center does not produce an impact on the network. Simulated results obtained using SIMULINK and DIgSILENT are presented and discussed.

The heritage of ancient buildings is an important part of the world's history and culture, which has an extremely rich historical-cultural value and artistic research value. Beijing has a large number of palace ancient buildings, and because of the age of their construction, many of them have problems of varying degrees of peeling and mold on the inner surfaces of the envelope. To solve the problems of the damp and moldy interior of palace buildings, a mathematical model of indoor heat and moisture transfer was established based on a wooden palace ancient building in Beijing. Through the indoor mold distribution validation model, the effects of outdoor humidity, soil moisture, wall humidity, and other factors on the indoor heat and moisture transfer of ancient buildings were simulated and analyzed by using the control variables method. The results showed that the molds were distributed at the indoor corners and floors, and the simulation of indoor humidity match the measured humidity. Thus, the simulation results were consistent with the actual situation. The variable trend of the relative humidity of the indoor environment with the outdoor humidity is inconsistent from plane to plane, i.e. it increases or remains constant with the increase of the outdoor humidity. The indoor ambient relative humidity increased with increasing the wall humidity. And the indoor average temperature is 23.3 ℃ and indoor relative humidity ranged between 90.9 % to 92.44 %. Soil moisture and wall humidity were the main factors affecting the indoor environmental relative humidity.

Copper indium gallium diselenide, Cu(In,Ga)Se2, thin-film of about 1.2 μm has been deposited on Mo coated soda lime glass by thermal co-evaporation of Cu, In, Ga, and Se sources. The thin film CIGS was characterized by energy dispersive spectroscopy (EDS) and identified the elemental composition of Cu, In, Ga and Se in the film. A CIGS device was completed by the successive deposition of multiple layers; SLG/Mo/CIGS/CdS/ZnO/ITO which yielded the efficiency of 11%. External spectroscopic ellipsometry (ex-situ SE) was performed on the completed device and the device analysis was performed. Starting with the parameterized complex dielectric functions of the individual component layers, SE analysis was performed using a step-wise procedure that ranks the fitting parameters according to their ability to reduce the mean square error (MSE) of the fit. The resulting layer thicknesses and dielectric functions were used to simulate the external quantum efficiency (EQE) of the device assuming complete active layer collection. Electronic losses were identified by comparison of simulated EQE with the measured EQE. The ultimate goal of this work is the optimization of narrow band-gap CIGS-related solar cells for the bottom layer in tandem devices.

This work deals with the evaluation of adhesive single-lap joints using ultrasonic guided waves. An adhesive bonded lap joint can be modelled as a three-layer system made up of two adherents and an adhesive. The propagation of guided waves in the joint is developed from matrix formulations. The behavior of the different guided wave modes that propagate in the bonded region is characterized and it is found that their relative amplitudes can be estimated based on the properties of the incoming wave that propagates in the non-bonded region. It was verified that the excitation of these modes is ruled by the degree in which the shapes of both modes match each other. A 3D simulation of two aluminium bonded plates using 500 kHz ultrasonic transducers in a pitch and catch configuration was implemented using the Matlab k-Wave toolbox. Scattering effects due to some produced defects located in the bond line of the lap joints were simulated. Experimental setup with some artificial defects produced in the aluminum joints were used in order to compare with the simulated. Qualitative agreement was observed for the two approaches. The observed deviation can be due to the different characteristics of the experimental and simulated defects.

To improve the wear resistance of polyimide (PI), surface modification was developed. In this study, the tribological properties of graphene (GN), graphene oxide (GO), and KH550-grafted graphene oxide (K5-GO) modified PI were evaluated by molecular dynamics (MD) at the atomic level. The findings indicated that the addition of nanomaterials can significantly enhance the friction performance of PI. The friction coefficient of PI composites decreased from 0.253 to 0.232, 0.136, and 0.079 after coating GN, GO and K5-GO, respectively. Among them, the K5-GO/PI exhibited the best surface wear resistance. Importantly, the mechanism behind the modification of PI was thoroughly revealed by observing the wear state, analyzing the changes of interfacial interactions, interfacial temperature, and relative concentration.

A wave is an energy that can propagate with a medium, the propagation of a wave moves with respect to time by carrying energy that moves with velocity per unit of time. Sea waves are one of the propagating wave problems that are broken down to produce wave propagation with a relatively inhomogeneous minimum amplitude and speed of sea waves which have their own difficulties in solving them numerically. This study aims to analyze the stability of wave propagation of submerged breakwaters using the Boundary Element Method. This research will approximate the boundary discretization of the breakwater domain and then combine it with the Finite Element Method in determining the moving elements of the velocity of fluid flow through a porous submerged breakwater. This study varies the magnitude of the incoming propagation velocity and the influence of the breakwater distance. The results of this study indicate that the resulting minimal wave assuming v = 1 m/s and the breakwater distance of s = 20 m gives a wave reflection with a minimum wave speed and amplitude of 0.12515 m

In this paper, we propose a modeling method based on peridynamics for ductile fracture at high temperatures. A thermoelastic coupling model combining peridynamics and classical continuum mechanics is used to limit the peridynamics calculations to the failure region of a given structure, thereby reducing computational costs. Then, a plastic constitutive model of peridynamic bonds is developed to capture the ductile-fracture process of the structure. Furthermore, an iterative algorithm for ductile-fracture calculation is presented. Finally, several numerical examples are shown. Particularly, the fracture processes of a superalloy structure under 800℃ and 900℃ environments are simulated and compared with experimental results. Our comparisons show that the crack modes captured by the proposed model are similar to experimental observations, which verifies the validity of the proposed model.

Enhancement in chemisorption is one of the active research areas in carbon materials. To remedy the thermally degraded chemisorption at high temperatures, we report a comprehensive study of kink structures in free-standing monoatomic carbon nanowires upon heating. Our Monte Carlo simulation considers multi-monoatomic carbon chains laterally interacted by the Van der Waals force. Our study reveals that the carbon nanowires maintain their linearity regardless of chain length at low temperatures, but this is not the case at high temperatures. Disordered kink structure is observed in the short carbon chains, especially above the Peierls transition temperature. The severe kink structure might increase the possibility of attaching negatively charged atoms, thereby contributing to the development of next-generation materials for chemisorption at high temperatures. We have also provided an important inspection that any physical property of the finite-length carbon chain predicted by ab-initio calculation should reconsider the atomic rearrangement due to the thermal instability at high temperatures.

The interaction between hard-core soft-shell colloids are characterized by having two characteristic distances: one associated with the penetrable, soft corona and another one corresponding to the impenetrable core. Isotropic core-softened potentials with two characteristic length scales have long been applied to understand the properties of such colloids. Those potentials usually show waterlike anomalies, and recent findings have indicated the existence of multiple anomalous regions in the 2D limit under compression, while in 3D only one anomalous region is observed. In this direction, we perform Molecular Dynamics simulations to unveil the details about the structural behavior in the quasi-2D limit of a core-softened colloid. The fluid was confined between highly repulsive solvophobic walls, and the behavior at distinct wall separation and colloid density was analyzed. Our results indicated a straight relation between the 2D or 3D-like behavior and the layers separation. We can relate that if the system behaves as independent 2D-layers, it will have a 2D-like behavior. However, for some separations the layers are connected, with colloids hopping from one layer to another – having then a 3D-like structural behavior. Those findings fill the gap in the depiction of the anomalous behavior from 2D to 3D.

ZnO was synthesized by Sol gel method using zinc nitrate as precursor at different calcination temperatures. Nucleation of ZnO crystallites and their growth with rise in temperature was observed. Exciton bands and lattice imperfections affected the absorption spectra. The decrease in band gap with temperature was due to the formation of defect energy levels. Phonon assisted non-radiative transitions caused broadening of the peaks. The possibility of tuning the band gap of ZnO by changing the temperature was explored. Simulation studies showed transition to single phase with rise in temperature.

There is increasing interest in automating train operations of mainline services, e.g. to increase network capacity. Automatic train operation (ATO) is already achieved by several pilot projects, but not implemented on a large scale. Before the general introduction of new or adapted technologies can have a transformative effect on the operation of such a complex system as train operation on mainlines, they have to pass functional, interoperability and performance tests. A virtual preliminary analysis is one way to ensure a smooth as well as safe introduction and implementation. This paper aims to present an approach that applies to the performance testing of ATO systems. Therefore, methods and test standards for technologies enabling automatic operation in other transport sectors are reviewed. The main findings have been adapted, transformed and combined to be used as a general strategy for virtual performance testing in the railway sector. Specifically, universal performance indicators, namely punctuality, accuracy, energy consumption, safety and comfort, are presented. A layer model for scenario description is adapted from the automotive sector, as well as the definition of different scenario types. Lastly, factors that can influence the performance of an ATO algorithm are identified. To demonstrate the developed approach, a straightforward investigation of a case study is conducted using a microscopic train simulator in combination with an ATO algorithm.

A multiscale modeling concept for numerical simulation of multiphysics turbulent flow utilizing map-based advection is described. The approach is outlined with emphasis on its theoretical foundations and physical interpretations in order to establish the context for subsequent presentation of the associated numerical algorithms and the results of validation studies. The model formulation is a synthesis of existing methods, modified and extended in order to obtain a qualitatively new capability. The salient feature of the approach is that time advancement of the flow is fully resolved both spatially and temporally, albeit with modeled advancement processes restricted to one spatial dimension. This one-dimensional advancement is the basis of a bottom-up modeling approach in which three-dimensional space is discretized into under-resolved mesh cells, each of which contains an instantiation of the modeled one-dimensional advancement. Filtering is done only to provide inputs to a pressure correction that enforces continuity and to obtain mesh-scale-filtered outputs if desired. The one-dimensional advancement, the pressure correction, and coupling of one-dimensional instantiations using a Lagrangian implementation of mesh-resolved volume fluxes is sufficient to advance the three-dimensional flow without time advancing coarse-grained equations, a feature that motivates the designation of the approach as autonomous microscale evolution (AME). In this sense, the one-dimensional treatment is not a closure because there are no unclosed terms to evaluate. However, the approach is additionally suitable for use as a subgrid-scale closure of existing large-eddy-simulation methods. The potential capabilities and limitations of both of these implementations of the approach are assessed conceptually and with reference to demonstrated capabilities of related methods.

The incorporation of unmanned aircraft terminal operations into the scope of Detect and Avoid systems necessitates analysis of the safety performance of those systems—principally, an assessment of how well those systems prevent loss of well clear from and collision with other aircraft. This type of analysis has typically been conducted by Monte Carlo simulation with synthetic, statistically representative encounters between aircraft drawn from an appropriate encounter model. While existing encounter models include terminal airspace classes, none explicitly represents the structure expected while engaged in terminal operations, e.g., aircraft in a traffic pattern. The work described herein is an initial model of such operations, scoped at this time specifically for assessment of unmanned aircraft landings and encounters with other aircraft either landing or taking off. The model shares the Bayesian network foundation of other MIT Lincoln Laboratory encounter models but tailors those networks to address structured terminal operations, i.e., correlations between trajectories and the airfield and each other. This initial model release is intended to elicit feedback from the standards-writing community.

For better understanding the corrosion and corrosion products behavior in the primary circuit of lead-bismuth eutectic (LBE) coolant reactor, the concentration distribution of soluble impurities and the transport of solid particles are investigated through finite-element method. An axisymmetric model of the primary circuit of LBE reactor was constructed to accelerate the calculation the thermal hydraulic filed of circuit. The saturation concentration of solute Fe, Cr and Ni in LBE coolant are identified through the equilibrium of their oxides and PbO. And the very different saturation concentrations of Fe/Cr/Ni in LBE will lead to significant element selective corrosion. The migration of solid oxides particles in the primary circuit is also investigated by the Euler-Lagrange tracing model. The simulation shows that driving force for the movement of particles >100 μm is buoyancy, which lets particles float on a free surface, while particles <10 μm tend to suspend in coolant. However, the behavior of particles also depends on the formation position, the particles formed above the core have the high possibility of re-entering in the core.

The once-held wisdom of the supreme efficiency of one-way streets has been gradually sup-planted by the perceived sustainability of two-way streets in the design of livable cities that prioritizes the safety of pedestrians and thriving of local businesses. However, it is rarely dis-cussed on whether one-way street conversions have truly improved the long-term traffic effi-ciencies on urban street networks, as conflating socioeconomic factors such as vehicular popula-tion growth and induced travel demand may render empirical analysis inconclusive. In this study, microscopic traffic simulations implemented on SUMO platform was performed to ana-lyze the effect of street conversion in Downtown Brickfields, Kuala Lumpur. This approach can control and standardize travel demand in both one-way and two-way street networks, and would therefore give a fairer evaluation by precluding all socioeconomic factors. It was found that one-way streets do not necessarily improve the traffic efficiency of the network, as it is very dependent on the traffic scenario evolution over time. One-way streets perform better at the on-set of traffic congestion due to its higher capacity, but on average, the 4-fold longer travel times that made it harder to clear traffic by getting vehicles to their destinations compared to two-way streets. As time progresses, congestion in one-way streets may become twice as worse compared to two-way streets. This study may contribute to a more holistic assessment of traffic circulation plan designed for smart and livable cities

The study of the influence of the nanoparticle volume fraction and aspect ratio of microchannels on the fluid flow and heat transfer characteristics of nanofluids in microchannels is important in the optimal design of heat dissipation systems with high heat flux. In this work, the computational fluid dynamics method was adopted to simulate the flow and heat transfer characteristics of two types of water–Al2O3 nanofluids with two different volume fractions and five types of microchannel heat sinks with different aspect ratios. Results showed that increasing the nanoparticle volume fraction reduced the average temperature of the liquid–solid heat transfer surface and thereby improved the heat transfer capacity of the nanofluids. Meanwhile, the increase of the nanoparticle volume fraction led to a considerable increase in the pumping power of the system. Changing the aspect ratio of the microchannel effectively improved the heat transfer capacity of the heat sink. Moreover, increasing the aspect ratio effectively reduced the average temperature of the heating surface of the heat sink without significantly increasing the flow resistance loss. When the aspect ratio exceeded 30, the heat transfer coefficient did not increase with the increase of the aspect ratio. The results of this work may offer guiding significance for the optimal design of high heat flux microchannel heat sinks.

There is a case about a system comprising two queues of M/M(a)/1/K with a due date with FCFS service policy in each queue. Using the methods of simulation and mathematical analysis, the solution diagrams were illustrated for the fixed due date Ɵ=1 second at the phase of due date up to the commencement of the service, limited capacity K₁=5 and K₂=4, for both scenarios of different service management rate resulted. For the analytical solution, first, a SAN model from the system was created in the Mobius tool. For simulation, a java discrete systems simulation code was used. Adjustment of the initial values, selection of the scenarios for service rate, the number of the consumers in the simulation, etc. were all carried out in the simulation code.

The increasingly used approach of combining different simulation software in testing of automated driving systems (ADS) increases the need for potential and convenient software designs. Recently developed co-simulation platforms (CSP) provide the possibility to cover the high demand on testing kilometers for ADS by combining vehicle simulation software (VSS) with traffic flow simulation software (TFSS) environments. The emphasis on the demand of testing kilometers is not enough to choose a suitable CSP. The complexity level of the used vehicle, object, sensors and environment models is essential for valid and representative simulation results. Choosing a suitable CSP raises the question of how the test procedures should be defined and constructed and what the relevant test scenarios are. Parameters of the ADS, the environments, objects, sensors in VSS as well as traffic parameters in TFSS can be used to define and generate test scenarios. In order to generate a large number of scenarios in a systematic and automated way, suitable and appropriate software designs are required. In this paper we present a software design for CSP based on the Model-View-Controller (MVC) design pattern and implementation of a complex CSP for virtual testing of ADS. Based on this design, an implementation of a CSP is presented using the VSS from IPG Automotive called CarMaker and the TFSS from PTV Group called Vissim. The results have shown that the presented CSP design and the implementation of the co-simulation can be used to generate relevant scenarios for testing of ADS.

History is often thought to be dull and boring – where large numbers of facts are memorized for passing exams. But the past informs the present and future, especially in delineating the context surrounding specific events that, in turn, help provide a deeper understanding of their causes and implications. Scientific progress (whether incremental or breakthroughs) is built upon prior work. Chronological examination of computational chemistry’s evolution reveals the existence of major “epochs” (e.g., transition from semi-empirical methods to first principles calculations), and the centrality of key ideas (e.g., Schrodinger equation and Born Oppenheimer approximation) in potentiating progress in the field. The longstanding question of whether computing power (both capacity and speed) or theoretical insights play a more important role in advancing computational chemistry was examined by taking into account the field’s development holistically. Specifically, availability of large amount of computing power at declining cost, and advent of graphics processing unit (GPU) powered parallel computing are enabling tools for solving hitherto intractable problems. On the other hand, this essay argues (using Born Oppenheimer approximation as an example) that theoretical insights’ role in unlocking problems through simple (but insightful) assumptions is often overlooked. Collectively, the essay should be useful as a primer for appreciating major development periods in computational chemistry, from which counterfactual questions illuminate the relative importance of theoretical insights and advances in computer science in moving the field forward.

Lassa virus (LASV) is responsible for a type of acute viral haemorrhagic fever referred to as Lassa fever. Lack of adequate treatment and preventive measures against LASV resulted in a high mortality rate in its endemic regions. In this study, a multi-epitope vaccine was designed using immunoinformatics as a prophylactic agent against the virus. Following a rigorous assessment, the vaccine was built using T-cell (N_CTL=8 and N_HTL=6) and B-cell (N_LBL=4) epitopes from each LASV-derived protein with suitable linkers and adjuvant. The physicochemistry, immunogenic potency and safeness of the designed vaccine (~68 kDa) were assessed. In addition, chosen CTL and HTL epitopes of our vaccine showed 97.37% worldwide population coverage. Besides, disulphide engineering also improved the stability of the chimeric vaccine. Molecular docking of our vaccine protein with toll-like receptor (TLR2) showed binding efficiency followed by dynamic simulation for stable interaction. Furthermore, higher levels of cell-mediated immunity and rapid antigen clearance were suggested by immune simulation and repeated-exposure simulation, respectively. Finally, the optimized codons were used in in silico cloning to ensure higher expression within E. coli K12 bacterium. With further assessment both in vitro and in vivo, we believe that our proposed peptide-vaccine would be potential immunogen against Lassa fever.

Physical-law based models are widely utilized in the aerospace industry. One such use is to provide flight dynamics models for use in flight simulators. For human-in-the-loop use, such simulators must run in real-time. Due to the complex physics of rotorcraft flight, to meet this real-time requirement, simplifications to the underlying physics sometimes have to be applied to the model, leading to model response errors in the predictions compared to the real vehicle. This study investigated whether a machine-learning technique could be employed to provide rotorcraft dynamic response predictions, with the ultimate aim of this model taking over when the physics-based model's accuracy degrades. In the current work, a machine-learning technique was employed to train a model to predict the dynamic response of a rotorcraft. Machine learning was facilitated using a Gaussian Process (GP) non-linear autoregressive model, which predicted the on-axis pitch rate, roll rate, yaw rate and heave responses of a Bo105 rotorcraft. A variational sparse GP model was then developed to reduce the computational cost of implementing the approach on large data sets. It was found that both of the GP models were able to provide accurate on-axis response predictions, particularly when the input contained all four control inceptors and one lagged on-axis response term. The predictions made showed improvement compared to a corresponding physics-based model. The reduction of training data to one-third (rotational axes) or one-half (heave axis) resulted in only minor degradation of the GP model predictions.

Network Simulators (NS) is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. This is the case of Mobile Ad hoc Networks (MANETs) which can be extensively used in emergency situations or to gather information without infraestructure. An important factor to get realiable results in the MANETs’ simulations is the wireless channel module of NSs. In this report, we explain how thw wireless channel is implemented in NS-3 and it can be configured.

In the development of automatic control, PID control is the oldest of the basic control mode, the control algorithm is the most widely used in engineering, especially the applied research of robustness has extensive engineering practical value. In this paper, based on the principle of the internal model PID parameter setting method was studied, through different approximate processing method, derived the three different formula of PID internal model setting and simulation verify the effectiveness of the algorithm. At the same time, the robustness of the controlled process under different parameter perturbation is theoretically analyzed and simulated.Finally, the paper summarizes the whole paper and looks forward to the future development trend.

The peri-urban and urban forests in Greece occupy a total area of 105.353 ha. In these vulnerable ecosystems, fire constitutes a natural disaster presenting particular challenges and specific difficulties. These include the high number of visitors as well as forests characteristics - such as the presence of particularly flammable tree species and high accumulation of combustible biomass – that make the on-start of fires more likely. The main purpose of the current research is to identify the optimum combination of silvicultural treatments to efficiently reduce potential forest fire severity and to facilitate their successful suppression by firefighting crews. In order to simulate the basic fire environment of urban forests, two main experimental plots were established and several tree and topographical characteristics were measured. Additionally, the NEXUS wildfire system was used to simulate forest fire potential behavior before and after the adoption of the silvicultural treatments that altered critical characteristics of the forest fire environment. The results clearly show that specific silvicultural prescriptions altered the type of forest fire spreading potential, revealing the overall efficiency of preventing actions during forest management.

Carrying out technological tests and research is indispensably connected with high costs and elongation of implementation time of new casting technologies and their modifications in industry. Hence, the application of specialised computer software, enabling the simulation and analysis of metallurgical and casting processes in modern foundry industry is of special interest. The present work presents an experimental application of MAGMASoft software in casting process of EV31A magnesium alloy structural element of helicopter engine. The results of computer simulation have been compared with industrial cast of the simulated element, fabricated in the same conditions. It has been revealed that the computer simulation provides a complex information on the analysed process, leading to reduction of costs and time, connected with technological tests in implementation of new casting technologies.

In this study, we repositioned thiopurine drugs used for the treatment of acute leukaemia as new tyrosinase inhibitors. Tyrosinase catalyses two distinct and successive oxidations in melanin biosynthesis: the conversions of tyrosine to dihydroxyphenylalanine (DOPA) and DOPA to dopaquinone. Continuous efforts are underway to discover small molecule inhibitors of tyrosinase for therapeutic, cosmetic, and agricultural purposes. Structure-based virtual screening has predicted inhibitor candidates for mushroom tyrosinase from drugs approved by the US Food and Drug Administration (FDA). Enzyme assays have confirmed the thiopurine leukaemia drug, thioguanine, as a tyrosinase inhibitor. Two other thiopurine drugs, mercaptopurine and azathioprine, were also evaluated for their tyrosinase inhibitory activity; mercaptopurine caused stronger inhibition than thioguanine did, whereas azathioprine was a poor inhibitor. The inhibitory constants of thioguanine and mercaptopurine were calculated as 52 and 16 µM, respectively, and the value of mercaptopurine was comparable to that of the well-known inhibitor kojic acid (13 µM). The cell lysate and melanin content assay in B16F10 melanoma cells confirmed that the compounds inhibited mammalian tyrosinase. In particular, 50 µM thioguanine reduced the melanin content by 57% without cytotoxicity. Furthermore, the thiopurine drugs shared little chemical similarity with the known tyrosinase inhibitors.

The accumulation of sea surface debris around the coastal waters of Malta poses significant ecological and environmental challenges, negatively affecting marine ecosystems and human activities. This issue is exacerbated by the lack of an effective system tailored to predict surface debris movement specifically for the Islands of Malta. To address this gap, a pipeline that combines a machine learning (ML) based prediction system with a physics-based model is proposed. This pipeline uses historical sea surface currents (SSC) velocities data to forecast future conditions and visualise debris movement. Central to this system are LSTM and GRU models, trained to predict SSC velocities for the next 24 hours for a specific area. These predictions are then utilised by a Lagrangian model to simulate and visualise the debris movement, providing insights into future dispersion patterns. A comparative evaluation of the models showed that the LSTM model outperformed the GRU model, with lower error metrics such as mean absolute error (MAE), mean squared error (MSE), and root mean squared error (RMSE), alongside narrower interquartile ranges (IQR). This method offers a tailored approach to addressing sea surface debris around Malta by accurately predicting SSC velocities and visualising debris movement, improving cleanup operations, and marine conservation strategies.

There are numerous approaches to model an influence of manufacturing parameters on the dissolution and disintegration of solid dosage forms. A modern approach for modelling and simulating complex and heterogeneous systems such as pharmaceutical tablets focuses on computationally-intensive finite-element or discreet element methods. Industrial challenges such as Process Analytical Technology (PAT) and Quality by Design are stimulating computer-based technologies to design, control and improve the quality of pharmaceutical compacts and their performance. In this study the disintegration and dissolution model based on the numerical solutions of the Noyes-Whitney equation and cellular automata supported disintegration model are proposed and evaluated. The results from in vitro release studies of the mefenamic acid formulations were compared to the calculated release patterns from the tablet structures obtained from microtomography experiments and the purely algorithmically created virtual tablets.

The domain of construction engineering and management is evolving rapidly. Optimizing resource positioning is crucial for meeting the challenges of efficiency and productivity. This research presents a novel methodology that incorporates Agent-Based Modeling (ABM), Building Information Modeling (BIM), and Bluetooth Low Energy (BLE) technologies, augmented with a Client Early Warning System (CEWS) and a Decision Support System (DSS). What makes this study unique is that it provides a real-time methodology for resource allocation and project management, tailored to address the complexities of modern construction projects. The application of this integrated technological framework marks a significant leap in construction management, empowering data-driven decision-making and significantly improving project efficiency. Empirically validated through a case study at Helwan University's College of Engineering and substantiated by expert surveys, this research showcases a transformative model for resource management. The findings not only underscore the practical applicability of this approach but also open new horizons for its adoption in global construction practices, offering insights for future research endeavors focused on expanding these methodologies to a wider range of resources.

Mathematical modeling is the most important tool for constructing the theory of different kinds of two-phase flows. The review is devoted to the analysis of the advent of the approach of mathematical modeling of two-phase flows, where solid particles act mainly as the dispersed phase. The main problems and features of the study of gas-solid two-phase flows are excluded. The main characteristics of gas flows with solid particles are given and the classification of two-phase flows is developed on their basis. The Lagrangian and Euler approaches to modeling the motion of a dispersed phase (particles) are described. Much attention is paid to the consideration of numerical simulation methods that describe descriptions of turbulent gas flow at different hierarchical levels (RANS, LES, DNS), different levels of description of interphase interactions (one-way coupling (OWC), two-way coupling (TWC) and four-way coupling (FWC)), as well as at different levels of interface resolution (partial-point (PP) and particle-resolved (PR)). Excluded are examples of some studies carried out on the basis of the identified approaches, as well as their exclusion for mathematical modeling of various classes of gas-solid two-phase flows.

We outline and test a new methodology for genuine simulation of stochastic processes with any dependence and any marginal distribution. We reproduce time dependence with a generalized, time symmetric or asymmetric, moving-average scheme. This implements linear filtering of non-Gaussian white noise, with the weights of the filter determined by analytical equations in terms of the autocovariance of the process. We approximate the marginal distribution of the process, irrespective of its type, using a number of its cumulants, which in turn determine the cumulants of white noise in a manner that can readily support the generation of random numbers from that approximation, so that it be applicable for stochastic simulation. The simulation method is genuine as it uses the process of interest directly without any transformation (e.g. normalization). We illustrate the method in a number of synthetic and real-world applications with either persistence or antipersistence, and with non-Gaussian marginal distributions that are bounded, thus making the problem more demanding. These include distributions bounded from both sides, such as uniform, and bounded form below, such as exponential and Pareto, possibly having a discontinuity at the origin (intermittence). All examples studied show the satisfactory performance of the method.

The planning and decision-making for a distributed energy supply concept in complex actor structures like in districts calls for the approach to be highly structured. Here, a strategy with strong use of energetic simulations is developed, the core elements are presented and research gaps are identified. The exemplary implementation is shown using the case study of a new district on the former Oldenburg airbase in northwestern Germany. The process is divided into four consecutive phases, which are carried out with different stakeholder participation and use of different simulation tools. Based on a common objective, a superstructure of the applicable technologies is developed. Detailed planning is then carried out with the help of a multi-objective optimal sizing algorithm and Monte Carlo based risk assessment. The process ends with the operating phase, which is to guarantee a further optimal and dynamic mode of operation. The main objective of this publication is present the core elements of the planning processes and decision-making framework based on the case study and to find and identify research gaps that will have to be addressed in the future.

The aim of this study is to obtain the Bayes estimators and the maximum likelihood estimators (MLEs) for the unknown parameters of the Rayleigh Weibull (RW) distribution based on progres-sive type-II censored samples. The approximate Bayes estimators are calculated using the idea of Lindley and Tierney-Kadane's approximation method under the squared-error loss function when the Bayes estimators are not handed in explicit forms. In this study, the approximate Bayes esti-mates are compared with the maximum likelihood estimates in the aspect of the estimated risks (ERs) using Monte Carlo simulation. In addition, the coverage probabilities of the parametric bootstrap estimates are calculated. Real lifetime data sets belonging to the cancer types as bladder cancer, head and neck cancer, and leukemia are used to illustrate the emprical results belonging to the approximate Bayes estimates, the maximum likelihood estimates, and the parametric bootstrap intervals.

Streamflow forecasting is of great importance in water resources management and flood warnings. Machine learning techniques can be utilized to assist with river flow forecasting. By analyzing historical time series data on river flows, weather patterns, and other relevant factors, machine-learning models can learn patterns and relationships to present predictions about future river flows. In this study, an Autoregressive Integrated Moving Average (ARIMA) model is constructed to predict the monthly flows of the Athabasca River at three monitoring stations: Hinton, Athabasca, and Fort MacMurray, in Alberta, Canada. The three monitoring stations upstream, midstream, and downstream were selected to represent the different climatological regimes of the Athabasca River. Time series data were used for the model training to identify patterns and correlations using moving averages, exponential smoothing, and Holt-Winters' method. The model's forecasting was compared against the observed data. The results show that the determination coefficients were 0.99 at all three stations, indicating strong correlations. The root mean square errors (RMSEs) were 26.19 at Hinton, 61.1 at Athabasca, and 15.703 at Fort MacMurray, respectively, and the mean absolute percentage errors (MAPEs) were 0.34%, 0.44%, and 0.14%, respectively. Therefore, the ARIMA model captured the seasonality patterns and trends in the stream flows at all three stations and demonstrated a robust performance for hydrological forecasting. This provides insights and predictions for water resources management and flood warnings.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

Time-of-Flight (ToF) cameras are subject to high levels of noise and errors due to Multi-Path-Interference (MPI). To correct these errors, algorithms and neuronal networks require training data. However, the limited availability of real data has led to the use of physically simulated data, which often involves simplifications and computational constraints. The simulation of such sensors is an essential building block for hardware design and application development. Therefore, the simulation data must capture the major sensor characteristics. This work presents a learning-based approach that leverages high-quality laser scan data to generate realistic ToF camera data. The proposed method employs MCW-Net (Multi-Level Connection and Wide Regional Non-Local Block Network) for domain transfer, transforming laser scan data into the ToF camera domain. Different training variations are explored using a real-world dataset. Additionally, a noise model is introduced to compensate for the lack of noise in the initial step. The effectiveness of the method is evaluated on reference scenes to quantitatively compare to physically simulated data.

This work proposes a conceptual design for a process for recovering Polystyrene (PS) using solvents of agro-industrial origin. The literature describes the dilution of Expanded Polyestyrene (EPS) in limonene, followed by its insolubilization with alcohols for recovery. However, there is no information on the solubility limit for the PS + limonene + alcohol system, which is critical for the process design. To determine the solubility limit, we diluted the waste EPS in D-limonene, mixed it with ethanol to form a precipitate, and used a gravimetric method to measure the mass of the compounds. These results allowed for the conceptual design of an EPS recycling process using a chemical process simulator, which includes a separator, a distillation column, and auxiliary equipment such as heaters, coolers, and pumps. An empirical correlation was obtained for the solubility limit, which enabled the design of a process for the treatment of 52 kg/s of PS using 0.75 kg /s of ethanol and 2.4 kg / s of D-limonene once the stationary state had been reached. The distillation column is six-stage, with a reflux ratio of 1.5 and duties of 30 000 kW and -25 847 kW for the condenser and reboiler, respectively.

The shear stress generated by wall turbulence is the main cause of wall friction resistance in turbulent flow through pipes. This paper investigates the impact of inserting rest periods (regions of constant Reynolds number) within the pulsating operating cycle of velocity on the fully turbulent flow at large time-averaged Reynolds numbers, using the Large Eddy Simulation (LES) method. The study aims to explore the effect of increasing rest periods within pulsations on drag resistance. The dimensionless shear stress and drag reduction rates during different time periods of rest were analyzed. Numerical simulation results indicate that the pulsating velocity operation mode does not necessarily lead to drag reduction; it may even result in increased resistance. Inserting rest periods within the pulsation cycle can achieve drag reduction effects, with the maximum drag reduction rate reaching 21.8\%. Comparisons with experimental data and Direct Numerical Simulation (DNS) from the literature validate the feasibility of using the LES method for pipe pulsating operation modes.

The study examines the noise, vibration, and harshness (NVH) management of electric vehicle (EV) powertrains, considering the challenges of the automotive industry's transition to electric drivetrains. The growing popularity of EVs brings new NVH challenges, as the lack of internal combustion engine (ICE) noise makes drivetrain noise more prominent. Key to managing NVH in EV powertrains is understanding the noise from electric motors, inverters, and gear systems. Noise from electric motors, mainly resulting from electromagnetic forces, and high-frequency noise generated by inverters significantly impact overall NVH performance. The article details sources of mechanical noise and vibration, including gear defects in gear systems and shaft imbalances. Methods presented in the publication include simulation and modeling techniques that help identify and solve NVH difficulties. Tools like multi-body dynamics (MBD), finite element method (FEM), and multi-domain simulation are crucial for understanding the dynamic behavior of complex systems. With the support of simulations, engineers can predict noise and vibration challenges and develop effective solutions during the design phase. The study emphasizes the importance of a system-level approach in NVH management, where the entire drivetrain is modeled and analyzed together, not just individual components.

In this study, we develop a stochastic partial differential equation (SPDE) model to assess the regional severity of temperature increases due to global warming. The model incorporates various stochastic processes to account for uncertainties such as solar explosions, economic upheavals, rising emissions, and irreversible changes in the climate system. Our base temperature model, influenced by latitude, is enhanced by these random factors to simulate realistic and diverse outcomes of climate change. Numerical simulations on a global grid provide a heatmap representing potential temperature increase severity across different regions. The results highlight the significant impact on tropical and polar regions, demonstrating the utility of SPDE models in understanding and predicting the complex dynamics of climate change. This approach offers valuable insights for policymakers and researchers aiming to develop adaptive strategies for mitigating the adverse effects of global warming.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

The use of energy resources is essential to the survival and development of human civilization. However, inefficient energy use not only has an impact on the economy, but it also has a significant impact on climate change. Studying and analyzing the factors that increase energy consumption is crucial for improving energy management. The aim of this study is to analyze the factors influencing energy savings in a building taken as a study model under two different climatic conditions. Measurements of the building's energy performance were carried out using the EnergyPlus calculation engine, which enabled us to analyze the strengths of building parameters such as the number of lights, the equipment used, occupancy, temperature and the relationships between the factors influenced. EnergyPlus is an important software tool in the field of building energy efficiency, enabling the precise simulation of building energy consumption. Simulation scenarios based on actual consumption data carried out by researchers have made it possible to develop energy management strategies in buildings in order to optimize energy efficiency, and in particular to promote the thermal performance of these buildings. In the present work, EnergyPlus building energy simulation software is used to simulate the energy consumption of the building of the Faculty of Electrical Engineering at the "Gheorghe Asachi" Technical University in Iasi, in order to determine the factors influencing building energy consumption. It has been shown that occupancy and heating and cooling systems are the key factors influencing energy consumption in buildings. The advantage of this study is that it can be used to model the most influential factors in predicting future energy consumption in buildings.

Nowadays, Multi-needle electrospinning has used to be an efficient method for producing nanofiber membranes. But in the process, the fluctuation errors in electrospinning fluid flow rate have directly influence the membrane quality, which bringing instability and still have not been solved yet. For finding out the solution to the inaccurate flow control in multi-needle, it is necessary to develop a multi-stage flow runner spinneret for large-scale production of nanofiber membrane. At first, the paper uses the finite element software COMSOL to numerically simulate the polymer flow in the runner of spinneret. Based on it, the velocity field distribution curve was draw and the velocity instability coefficient of the polymer flow was attained, which are providing theoretical guidance for the optimal design of spinneret. Next, the response surface analysis method (RSM) was used to establish a regression model between the average diameter of the nanofiber membrane and the process parameters. Then, above regression model used to perform variance data processing between the average diameter and the process parameter configuration. After that, the 2D and 3D response surface profiles and the significance analysis were completed. Finally, the stability of the nanofibers production was improved, which attained the optimal adjustment of process configuration in multi-needle electrospinning.

This paper introduces a low-tech capacitive micromachined ultrasonic transducer (CMUT) designed with low environmental footprint materials. The fabrication process involves a copper plate as the fixed bottom electrode, a polymer-based adhesive as a dielectric material, and an aluminum foil as the top electrode.Finite element simulations include studies of displacement, mechanical stresses, and eigenfrequency. Experimental measurements validate the device's electromechanical behavior, showing an eigenfrequency of 88.6 kHz and a displacement of 22 pm. The low-tech CMUT demonstrates potential for applications such as ultrasonic actuation and energy harvesting, offering simplicity, biocompatibility, and low environmental impact. While not directly ready for applications, these transducers provide hands-on experience with technology similar to high-performance silicon-based implementations. These low-tech MUTs are perfect practical case studies for teaching purposes, combining simulation and experimental validation.

Schistosomiasis, acquired by skin-penetrating cercariae of dioecious digenean schistosomes during freshwater contact, afflicts nearly 260 and 440 million people with active infections and residual morbidity, respectively; about 10 million women at reproductive age contract schistosomiasis during gestation every year. Acute schistosomiasis is characterized by pre-patent pro-inflammatory CD4+ T-helper 1 or CD4+ Th1/T-helper 17 reactivity against immature schistosomulae. Chronic schistosomiasis is dominated by post-patent anti-inflammatory CD4+ T-helper 2 reactivity against ova epitopes; flukes co-exist in immunocompetent definitive hosts as they are capable of evading their defense mechanisms. Preventive measures should be complemented by vaccination, inducing long-term protection against transmission, infection, and disease recurrence, given the latest advancements in schistosomal vaccines. Transmission models incorporating vaccination available in PubMed, Embase and Web of Science up to December 31, 2023 are presented. Besides conceptual model differences, predictions meant to guide decision- and policymaking reveal continued worm harboring facilitating transmission besides residual infections, and increased susceptibility to re-infection and rebound morbidity, both shifted to later life stages following the intervention. Consequently, a vaccination schedule is pivotal considering the optimal age for initial immunization, i.e., pre-schoolchildren or schoolchildren, in a cohort-based or population-based manner while incorporating potential non-adherers promoting ongoing transmission; longevity over magnitude of vaccine protection to antigenic schistosomal moieties is crucial including accounting for existing pre-acquired immunity from natural exposure, in utero priming besides herd immunity, and induced by chemotherapy. Combining as one multi-component approach long-term effects of vaccination with short-term effects of chemotherapy as regular repeated vaccine-linked therapy in contrast to a single-component intervention seems most promising for achieving WHO’s endpoints of transmission elimination and morbidity control.

Community centers play a crucial role in urban environments, providing physical and educational services to their surrounding communities, particularly for students. Among the many benefits for students are enhanced academic outcomes, improvement of behavioral problems, and increased school attendance. Such centers are also particularly vital for low-income and racial minority students as they are pivotal in giving them outside-of-school learning opportunities. However, determinants influencing attendance at community centers remain largely unexplored. Using census data, Boston Centers for Youth and Families (BCYF) attendance data, and specific center attributes, we develop human mobility gravitational models to predict attendance across the BCYF network. Using those models, we investigate the potential effects on general and student attendance by changing center attributes, such as facilities and operating hours. We also research the impact of changing the walking accessibility to those centers on their respective attendance patterns. After the analysis, we find that the most cost-effective policy to increase BCYF attendance is changing each center’s educational and recreational offerings far beyond any accessibility interventions. Our results provide insights into potential policy changes that could optimize the attendance and reach of BCYF Community Centers to underserved populations.

Purpose of review The forest industry has deployed ICTs to improve productivity of forest supply chains. In this sense, digitalization of data flows significantly impacts wood supply chains, from forest to mills, which must react flexibly to market fluctuations of forest products. The goal of this study was to conduct a literature review on data flow implementations in management systems of wood supply chains and to evaluate their applicability in supply chains to analyze the opportunities for improving them in practice. Recent findings We utilized the ScienceDirect database, Scopus and Web of Science in order to document data flows in systems and actual applications. Due to ongoing outsourcing, the wood procurement chains, and the wood supply chains were identified in the forest industry. Several different technologies can be implemented also in wood supply chains to digitalize the data flow depending on the specific needs of organizations. In this regard, digitalization of Big Data causes significant changes in elements of supply models that should be integrated and standardized in the optimization and simulation systems. Summary A modelling guide is suggested for accurate dynamic solution of problems of forest logistics. Then, the opportunities in digitalization for connecting different data flows, technologies, and stakeholders are discussed thoroughly. We conclude that data-driven dynamic optimization, and locally implemented digitalization contributes to wood supply modeling in the establishment of standards for cloud-based platforms at time-related and sequential measures which will ensure successful forest logistics through the planning and the monitoring of wood supply chains.

This paper presents a model for determining the availability of continuous systems at open pits using the neuro-fuzzy system. The concept of availability is divided into partial indicators (synthetic indicators and sub-indicators). The presented model in relation to already existing models for determining availability uses a combination of the advantages of artificial neural networks and fuzzy logic. The case study was done for the I ECC (bucket wheel excavator – conveyors – crushing plant) system of the open pit Drmno, Kostolac. In this paper, in addition to the ANFIS model for determining the availability of continuous systems, a simulation model was developed. The obtained results of the ANFIS model were verified with the help of a simulation model that uses certain assumptions about the distribution of failures. This paper was created as a result of several years of field and theoretical research into the availability of continuous sys-tems in open-pit mines, and completes a cycle that consists of several published articles on the subject of modeling the behavior of these systems in real time using a time picture of the state, expert assessment, simulation and AI models, respecting the multidisciplinarity of the problem (mining-technological, mechanical, information-technological aspects).

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

Hydrogen storage in high pressure tanks can occur with different filling strategies. Many studies have been carried out on supplies with increasing pressure rates. However, hydrogen filling with constant mass inflow rate have not received the same attention. The present work aims to carry out numerical simulations to study hydrogen flow, in a type 3 tank of 70 MPa NWP and constant inflow rate condition. From the analysis of the results, it was possible to verify that there is a linear relationship between the increase in the total equilibrium temperature and the final hydrogen temperature. There is also a linear increasing relationship between Inlet and final temperatures when the equilibrium temperature is fixed. Considering fully adiabatic walls results in significant increases in temperature. The difference between total and static temperatures found in the Inlet tube decreases with the decrease in mass flow rate. The choice of a polymer for the tank lining led to higher temperatures when compared to an aluminum lining.

The crosslinking behavior of polyethylene (PE) determines its exceptional performance and application. In this study, we investigated the crosslinking behaviors of different PE resins through model simulation and rheological methods. Specifically, the mathematical equation of "S" model was established for PE resin. According to this equation, the optimal maximum gel content for high-density polyethylene (HDPE) was found to be around 85%. Moreover, the maximum crosslinking degrees for different PE resins depended largely on their density and molecular weight. The melt viscosities before crosslinking in PE resins were highly influenced by their melt index. The higher melt indexes resulted in the lower storage moduli, improving melt processability during processing. In addition, the crosslinking rates of PE resins were strongly influenced by peroxide concentration, independent of PE resin structures. For high molecular weight and low-density PE resins, they exhibited decreased ti values, increased A0 values, and decreased k6 values. However, there were no noticeable variations in the values of k2 and phi among different PE resins. And all simulated modeling outcomes showed the remarkable consistency with the experimental rheological data. These findings are of utmost significance in the industrial manufacture of PE resin.