This research aims to determine the influence of the independent commissioners, audit committee, institutional ownership, firm size and leverage against the integrity of the financial reporting information. This research is quantitative research with the causal approach. This study uses secondary data and panel data regression analysis method. The research results prove that audit committee, institutional ownership and leverage effect on the integrity of the financial reporting information. But it does not prove that the independent commissioner and firm size effect on the integrity of the financial reporting information.

The relationship between city size, coastal land use and air temperature rise with distance from coast during summer day is analyzed using the meso-scale Weather Research & Forecasting (WRF) model in five coastal cities in Japan with different sizes and coastal land use (Tokyo, Osaka, Nagoya, Hiroshima and Sendai) and inland cities in Germany (Berlin, Essen and Karlsruhe). Air temperature increased as distance from the coast increased, reached its maximum, and then decreased slightly. In Nagoya and Sendai, the number of urban land use in coastal areas is less than the other three cities, where air temperature is a little lower. As a result, air temperature difference between coastal and inland urban area is small and the curve of air temperature rise is smaller than those in Tokyo and Osaka. In Sendai, air temperature in the inland urban area is the same as in the other cities, but air temperature in the coastal urban area is a little lower than the other cities, due to about one degree lower sea surface temperature influenced by the latitude. In three German cities, the urban boundary layer may not develop sufficiently because the fetch distance is not enough.

At room temperature, the indentation morphologies of crystalline copper with different grain size including nanocrystalline (NC), ultrafine-grained (UFG) and coarse-grained (CG) copper were studied by nanoindentation at the strain rate of 0.04/s without holding time at indentation depth of 2000 nm. As the grain size increasing, the height of the pile-up around the residual indentation increases and then has a slightly decrease in the CG Cu, While the area of the pile-up increases constantly. Our analysis has revealed that the dislocation motion and GB activities in the NC Cu, some cross- and multiple-slips dislocation insides the larger grain in the UFG Cu, and forest dislocations from the intragranular Frank-Read sources in the CG Cu, would directly induce these distinct pile-up effect.

The energy, momentum and the action associated with the time domain transition radiation fields are investigated. The results show that for a charged particle moving with speed $v$, the longitudinal momentum associated with the transition radiation is approximately equal to $E/c$ for values of $1-v/c$ smaller than about 10^-3 where $E$ is the total radiated energy and c is the speed of light in free space. The action of the transition radiation, defined as the product of the energy dissipated and the duration of the emission, increases as $1-v/c$ decreases and, for an electron, it becomes equal to $h/4\pi$ when $v=c-v_m$ where $v_m$ is the speed associated with the lowest energy state of a particle confined inside the universe and h is the Plank constant. Combining these results with Heisenberg’s uncertainty principle, an expression for the electronic charge based on other fundamental physical constants is derived. The best agreement between the experimentally observed electronic charge and the theoretical prediction is obtained when one assumes that the actual size of the universe is about 250 times larger than the visible universe.

Hydroperoxides (ROOH) are known as damaging agents capable of mediating mutation, while a role as signaling agents through oxidation of protein sulfhydryls that can alter cancer-related pathways has gained traction. Glutathione peroxidase 2 (GPX2) is an antioxidant enzyme that reduces ROOH at the expense of glutathione (GSH). GPX2 is noted for a tendency of large in-creases or decreases in expression levels during tumorigenesis that leads to investigators focusing on its role in cancer. However, GPX2 is only one component of multiple enzyme families that metabolize ROOH and GPX2 levels are often very low in the context of these other ROOH reducing activities. Colorectal cancer (CRC) was selected as a case study for examining GPX2 function as colorectal tissues and cancers are sites where GPX2 is highly expressed. A case can be made for a significant impact of changes in expression levels. There is also a link between GPX2 and NADPH oxidase 1 (NOX1) from earlier studies that is seldom addressed and is discussed, presenting data on a unique association in colon and CRC. Tumor-derived cell lines are quite commonly used for pre-clinical studies involving the role of GPX2 in CRC. Generally, selection for this type of work is limited to identifying cell lines based on high and low GPX2 expression with the standard re-search scheme of overexpression in low expressing lines and suppression in high expressing lines to identify impacted pathways. This overlooks CRC subtypes among cell lines involving a wide range of gene expression profiles and a variety of driver mutation differences along with a large difference in GPX2 expression levels. A trend for low and high GPX2 expressing cell lines to segregate into different CRC subclasses, indicated in this report, suggests that choices based solely on GPX2 levels may provide misleading and conflicting results by disregarding other properties of cell lines and failing to factor in differences in potential protein targets of ROOH. CRC and cell line classification schemes are presented here that were intended to assist workers in performing pre-clinical studies but are largely unnoted in work on GPX2 and CRC. Studies are often initiated on the premise that the transition from normal to CRC is associated with up-regulation of GPX2. This is probably correct. However, the source normal cells for CRC could be almost any colon cell type, some with very high GPX2 levels. These factors are addressed in this study.

Gradients of smooth functions with non-independent variables are relevant for exploring complex models and for the optimization of functions subjected to constraints. In this paper, we investigate new and simple approximations and computations of such gradients by making use of independent, central and symmetric variables. Such approximations are well-suited for applications in which the computations of the gradients are too expansive or impossible. The derived upper-bounds of the biases of our approximations do not suffer from the curse of dimensionality for any $2$-smooth function, and theoretically improve the known results. Also, our estimators of such gradients reach the optimal (mean squared error) rate of convergence (i.e., $\mathcal{O}(N^{-1})$) for the same class of functions. Numerical comparisons based on a test case and a high-dimensional PDE model show the efficiency of our approach.

Selective mutism (SM) is an “Anxiety Disorder” characterized by a child’s “persistent inability” to communicate verbally in some (or all) contexts of social life that is associated with other cognitive-affective disorders. Cognitive-behavioural assessment and psychological intervention may be complex to be performed due to both the difficulty to administered standardized neuropsychological batteries (e.g., language-mediated tests) and the difficulty to involve family and teachers in the intervention program, respectively. Here, a single-case study is described in which a female Filipina child with SM underwent a comprehensive neuropsychological assessment and multimodal therapeutical intervention between the ages of 7 to 11 years. More specifically, the psychological intervention included cognitive-behavioral psychotherapy to both improve social-cognitive skills and learning abilities and to reduce anxiety, and speech therapy. Moreover, the parents and teachers were actively involved in the therapeutic process and they were also administered a psycho-education program. After this specific treatment, at the age of 11 years the girl began to verbalize in both therapy and school contexts, although she still was used to adopt non-verbal strategies. A parallel and gradual improvement in communicative-linguistic skills and school learning was also observed. In conclusion, the present report highlights the importance to apply an "integrated and multimodal intervention" to treat SM in children that includes also psycho-education intervention for both parents and teachers.

Assessing observation noise is a critical step in the development of a stochastic model for GNSS navigation and positioning. This process ensures that the statistical properties of the observational data are accurately characterized, leading to more reliable and precise positioning results. Traditionally, the one sigma values for observation noise, 0.3 m for code and 3 mm for carrier phase, alongside elevation-dependent weighting schemes, have been standard. However, these may no longer be suitable due to significant advancements in GNSS systems, receivers, and antennas. Previous research predominantly focused on code type and PPP techniques, often limited by the inability to separately assess observation types across different frequency bands due to ionospheric delay. Furthermore, these studies were generally constrained by limited experimental data. This research advocates for the use of ultra-short baselines to eliminate atmospheric delay and other error sources, providing a detailed assessment of observation noise for various frequency bands, GNSS systems, and receiver & antenna types over an extensive period and across multiple baselines. The findings suggest a need to reconsider traditional one sigma values and elevation-dependent weighting schemes for current applications.

Brain pathological changes impair cognition early in disease etiology. There is an urgent need for understanding aging-linked mechanisms of early memory loss to develop therapeutic strategies and prevent the development of cognitive impairment. Tusc2, also named Fus1, is a mitochondrial-resident protein regulating Ca2+ fluxes to and from mitochondria impacting overall health. We reported that Tusc2-/- female mice develop chronic inflammation and age prematurely, causing age- and gender-dependent spatial memory deficits at 5 m.o. Therefore, we investigated Tusc2-dependent mechanisms of memory impairment in mice, comparing changes in resident and brain-infiltrating immune cells. Interestingly, Tusc2-/- female mice demonstrated proinflammatory increase in astrocytes, IFN-γ expression in CD4+T cells and Granzyme-B in CD8+T cells. We also found fewer FOXP3+ T-regulatory cells and Ly49G+ NK and Ly49G+ NKT cells in female Tusc2-/- brain, suggesting a weakened anti-inflammatory response. Moreover, Tusc2-/- hippocampi exhibited Tusc2- and sex-specific protein changes associated with brain plasticity, including mTOR activation, and Calbindin and CamKII dysregulation affecting intracellular Ca2+ dynamics. Overall, data suggest that dysregulation of Ca2+-dependent processes and proinflammatory brain microenvironment heighten in Tusc2-/- mice could underlie cognitive impairment. Thus, strategies to modulate the brain’s Tusc2-, Ca2+, and mitochondria-dependent pathways should be explored to improve cognitive health.

We consider a Cauchy problem for differential equations in a Hilbert space $X$. The problem is stated in a time interval $I$, which can be finite or infinite. Weuse a fixed point argument for history-dependent operators to prove the unique solvability of the problem. Then, we state and prove convergence criteria for both a general fixed point problem and thecorresponding Cauchy problem. These criteria provide necessary and sufficient conditions on a sequence $\{u_n\}$ which guarantee its convergence to the solution of the corresponding problem, in the space of both continuous and continuously differentiable functions. We then specify our results in the study of a particular differential equation governed by two nonlinear operators. Finally, we provide an application in viscoelasticity and give a mechanical interpretation of the corresponding convergence result.

From the first isolation of the cystovirus bacteriophage Φ6 from Pseudomonas syringae 50 years ago, we have progressed to a better understanding of the structure and transformations of the many parts of the virion. The three-layered virion encapsulating the tripartite double stranded RNA (dsRNA) genome, breaches the cell envelope on infection, generates its own transcripts, and coopts the bacterial machinery to produce its proteins. The generation of new virions starts with a procapsid with a contracted shape, followed by packaging single stranded RNA segments with concurrent expansion of the capsid, and finally replication to reconstitute the dsRNA genome. The outer two layers are then added, and the fully formed virions released by cell lysis. Most of the procapsid structure composed of the proteins P1, P2, P4 and P7 is now known, as well as its transformations to the mature, packaged nucleocapsid. The outer two layers are less well studied. One additional study investigated the binding of the host protein YajQ to the infecting nucleocapsid, where it enhances the transcription of the large RNA segment that codes for the capsid proteins. Finally, we relate the structural aspects of bacteriophage Φ6 top those of other dsRNA viruses, noting the similarities and differences.

The integrated stress response is a signaling network comprised of four branches, each of which senses different cellular stressors, converging on the phosphorylation of eIF2α to depress global translation and initiate recovery. One of these branches is composed of GCN2, which senses cellular amino acid insufficiency and participates in the maintenance of amino acid homeostasis. Previous studies have shown that GCN2 is a viable cancer target when amino acid stress is provoked by inhibiting an additional target. In this light, we screened a combination of drugs to identify biologically active compounds which synergize with the GCN2 inhibitor TAP20. First, a panel of 25 compounds was assayed in six cancer cell lines for drug sensitivity. Each compound was then combined with TAP20 at concentrations below their IC50, and the impact on cell growth was assessed. Selected strongly synergistic combinations were further characterised using synergy analyses and matrix-dependent invasion assays. Inhibitors of proteostasis, of the MEK-ERK pathway and pan-CDK inhibitors flavopiridol and seliciclib were found to potently synergize with TAP20 in two of the tested cell lines. Among their common CDK targets is CDK7, which was selectively targeted with THZ-1 and found to synergize with TAP20. Finally, these combinations were found to be partially synergistic when assessed using matrix-dependent invasion assays. However, we found that TAP20 alone was sufficient to restrict invasion at concentrations well below its growth-inhibitory IC50. We conclude that GCN2 can be targeted for treating cancers by polytherapy or even monotherapy.

Two monoclonal antibodies (mAbs) against human epidermal growth factor receptor 2 (HER2), trastuzumab and pertuzumab, were clinically approved. We previously developed a highly sensitive and specific anti-HER2 mAb, H2Mab-139 (mouse IgG1, kappa). In this study, we produced a defucosylated IgG2a version of anti‑HER2 mAb (H2Mab-139-mG2a-f) to enhance ADCC-mediated antitumor activity. H2Mab-139-mG2a-f exhibits a high binding affinity in flow cytometry with the dissociation constant (KD) determined to be 3.9 × 10‑9 M and 7.7 × 10‑9 M against HER2‑overexpressed Chinese hamster ovary (CHO)-K1 (CHO/HER2) and HER2-positive BT-474 cells, respectively. Moreover, we showed that H2Mab-139-mG2a-f exerted ADCC and complement-dependent cytotoxicity against CHO/HER2 and BT-474 cells in vitro and exhibited potent antitumor activities in the xenograft models. These results indicated that H2Mab-139-mG2a-f exerts antitumor effects against HER2-positive human breast cancers and could be useful for an antibody treatment regimen for HER2-positive human cancers.

This paper discusses a passive control issue for Nonlinear Time-Varying (NTV) systems subject to stability and attenuation performance. Based on the modeling approaches of Takagi-Sugeno (T-S) fuzzy model and the Linear Parameter-Varying (LPV) model, a Parameter-Dependent Polynomial Fuzzy (PDPF) model is constructed to represent the NTV systems. According to Parallel Distributed Compensation (PDC) concept, a parameter-dependent polynomial fuzzy controller is built to achieve robust stability and passivity of PDPF model. Furthermore, the passive theory is applied to achieve the performance constraining the disturbance effect on the PDPF systems. To develop the stability criteria, by introducing a parameter-dependent polynomial Lyapunov function, one can derive some stability conditions which belong to the term of Sum-Of-Squares (SOS) form. Based on the Lyapunov function, two stability criteria are proposed to design the corresponding PDPF controller such that the NTV system is robustly stable and passive. Finally, a numerical example is applied to demonstrate the effectiveness of the proposed stability criterion.

To understand the evolution of the human norovirus GII.P6-GII.6 and GII.P7-GII.6 strains, we analyzed both the RdRp region and VP1 gene in globally collected strains using authentic bioinformatics technologies. A common ancestor of the P6- and P7-type RdRp region emerged approximately 50 years ago and a common ancestor of the P6- and P7-type VP1 gene emerged approximately 110 years ago. Subsequently, the RdRp region and VP1 gene evolved. Moreover, the evolutionary rates were significantly faster for the P6-type RdRp region and VP1 gene than the P7-type RdRp region and VP1 genes. Large genetic divergence was observed in the P7-type RdRp region and VP1 gene compared with the P6-type RdRp region and VP1 gene. The phylodynamics of the RdRp region and VP1 gene fluctuated after the year 2000. Positive selection sites in VP1 proteins were located in the antigenicity-related protruding 2 domain, and these sites overlapped with conformational epitopes. These results suggest that the GII.6 VP1 gene and VP1 proteins evolved uniquely due to recombination between the P6- and P7-type RdRp regions in the HuNoV GII.P6-GII.6 and GII.P7-GII.6 virus strains.

Calcium/calmodulin (CaM)-dependent protein kinase kinase 2 (CaMKK2) regulates bone remodeling through its effects on osteoblasts and osteoclasts. However, its role in osteocytes, the most abundant bone cell type, and the master regulator of bone remodeling, remains unknown. Here we report that the conditional deletion of CaMKK2 from osteocytes using Dentine matrix protein 1 (Dmp1)-8kb-Cre mice led to enhanced bone mass only in female mice owing to a suppression of osteoclasts. Conditioned media isolated from female CaMKK2-deficient osteocytes inhibited osteoclast formation and function in in vitro assays, indicating a role for osteocyte-secreted factors. Proteomics analysis revealed significantly higher levels of extracellular calpastatin, a specific inhibitor of calcium-dependent cysteine proteases calpains, in female CaMKK2 null osteocyte conditioned media, compared to media from female control osteocytes. Further, exogenously added non-cell permeable recombinant calpastatin domain I elicited a marked, dose-dependent inhibition of female wild-type osteoclasts and depletion of calpastatin from female CaMKK2-deficient osteocyte conditioned media reversed the inhibition of matrix resorption by osteoclasts. Our findings reveal a novel role for extracellular calpastatin in regulating female osteoclast function and unravel a novel CaMKK2-mediated paracrine mechanism of osteoclast regulation by female osteocytes.

The resistance of cancer cell subpopulations, including cancer stem cell (CSC) populations, to apoptosis-inducing chemotherapeutic agents is a key barrier to improved outcomes for cancer patients. The cationic amphiphilic drug hexamethylene amiloride (HMA) has been previously demonstrated to efficiently kill bulk breast cancer cells independent of tumor subtype or species, but acts poorly toward non-transformed cells derived from multiple tissues. Here we demonstrate that HMA is similarly cytotoxic toward breast CSC-related subpopulations that are resistant to conventional chemotherapeutic agents, but poorly cytotoxic toward normal mammary stem cells. HMA inhibits the sphere-forming capacity of FACS-sorted human and mouse mammary CSC-related cells in vitro, specifically kills tumor but not normal mammary organoids ex vivo, and inhibits metastatic outgrowth in vivo, consistent with CSC suppression. Moreover, HMA inhibits viability and sphere formation by lung, colon, pancreatic, brain, liver, prostate and bladder tumor cell lines, suggesting that its effects may be applicable to multiple malignancies. Mechanistically, HMA elicits the permeabilization of the limiting lysosomal membrane, a hallmark feature of the lysosome-dependent cell death pathway. Our observations expose a key vulnerability intrinsic to cancer stem cells, and point to novel strategies for the exploitation of cationic amphiphilic drugs in cancer treatment.

Neurological complications of infection by the mosquito-borne Zika virus (ZIKV) include Guillain-Barré syndrome (GBS), an acute inflammatory demyelinating polyneuritis. GBS was first associated with recent ZIKV epidemics caused by the emergence of ZIKV Asian lineage in South Pacific. Here, we hypothesize that ZIKV-associated GBS relates to a molecular mimicry between viral envelope E (E) protein and neural proteins involved in GBS. Analysis of ZIKV epidemic strains showed that glycan loop (GL) region of the E protein includes an IVNDT motif which is conserved in voltage-dependent L-type calcium channel subunit alpha-1C (Cav1.2) and Heat Shock 70 kDa protein 12A (HSP70 12A). Both VSCC-alpha 1C and HSP70 12A belong to protein families which have been associated with neurological autoimmune diseases in central nervous system. The purpose of our in silico analysis is to point out that IVNDT motif of ZIKV E-GL region should be taken in consideration for the development of safe and effective anti-Zika vaccines by precluding the possibility of adverse neurologic events including autoimmune diseases such as GBS.

We propose an iterative scheme for feature-based positioning using a new weighted dissimilarity measure with the goal of reducing the impact of large errors among the measured or modeled features. The weights are computed from the location-dependent standard deviations of the features and stored as part of the reference fingerprint map (RFM). Spatial filtering and kernel smoothing of the kinematically collected raw data allow efficiently estimating the standard deviations during RFM generation. In the positioning stage, the weights control the contribution of each feature to the dissimilarity measure, which in turn quantifies the difference between the set of online measured features and the fingerprints stored in the RFM. Features with little variability contribute more to the estimated position than features with high variability. Iterations are necessary because the variability depends on the location, and the location is initially unknown when estimating the position. Using real WiFi signal strength data from extended test measurements with ground truth in an office building, we show that the standard deviations of these features vary considerably within the region of interest and are neither simple functions of the signal strength nor of the distances from the corresponding access points. This is the motivation to include the empirical standard deviations in the RFM. We then analyze the deviations of the estimated positions with and without the location-dependent weighting. In the present example the maximum radial positioning error from ground truth are reduced by 40% comparing to kNN without the weighted dissimilarity measure.

This work presents a novel approach to construct surrogate models of parametric Differential Algebraic Equations based on a tensor representation of the solutions. The procedure consists in building simultaneously, for every output of the reference model, an approximation given in tensor-train format. A parsimonious exploration of the parameter space coupled with a compact data representation allows to alleviate the curse of dimensionality. The approach is thus appropriate when many parameters with large domains of variation are involved. The numerical results obtained for a nonlinear elasto-viscoplastic constitutive law show that the constructed surrogate model is sufficiently accurate to enable parametric studies such as the calibration of material coefficients.

The open communication is an exigent need for future power system where the time delay is unavoidable. In order to secure the stability of the grid, the frequency must remain within its limited range which is achieved through the load frequency control. The load frequency control signals are transmitted through communication networks which induces time delay that could destabilize the power systems. So, in order to guarantee the stability the delay margin should be computed. In this paper, we present a new method for calculating the delay margin in load frequency control systems. The transcendental time delay characteristics equation is transformed to frequency dependant equation. The spectral radius is used to find the frequencies at which the roots crosses the imaginary axis. The crossing frequencies are determined through the sweeping test and the binary iteration algorithm. A one-area load frequency control system is chosen as case study. The effectiveness of the proposed method has been proved through comparing with the most recent published methods. The method shows its merit with less conservativeness and less computations. The PI controller gains are preferable to be chosen large to reduce the damping, however, the delay margin decreases with increasing the PI controller gains.

Initial attempts to develop monoclonal antibodies as therapeutics to resolve influenza infections focused mainly on searching for antibodies with the potential to neutralise the virus in vitro with classical haemagglutination inhibition and micro-neutralisation assays. This led to the identification of many antibodies that bind to the head domain of haemagglutinin (HA) which generally have potent neutralisation capabilities that block viral entry or viral membrane fusion. However, this class of antibodies has a narrow breadth of protection in that they are usually strain specific. This led to the emphasis on stalk targeting antibodies which are able to bind a broad range of viral targets that span across different influenza subtypes. Recently, a third class of antibodies targeting the vestigial esterase (VE) domain have been characterised. In this review, we describe the key features of neutralising VE targeting antibodies and compare them with head and stalk class antibodies.

Many systems in nature and laboratories are far from equilibrium and exhibit significant fluc- tuations, invalidating the key assumptions of small fluctuations and short memory time in or near equilibrium. A full knowledge of Probability Distribution Functions (PDFs), especially time- dependent PDFs, becomes essential in understanding far-from-equilibrium processes. We consider a stochastic logistic model with multiplicative noise, which has gamma distributions as stationary PDFs. We numerically solve the transient relaxation problem, and show that as the strength of the stochastic noise increases the time-dependent PDFs increasingly deviate from gamma distributions. For sufficiently strong noise a transition occurs whereby the PDF never reaches a stationary state, but instead forms a peak that becomes ever more narrowly concentrated at the origin. The addition of an arbitrarily small amount of additive noise regularizes these solutions, and re-establishes the existence of stationary solutions. In addition to diagnostic quantities such as mean value, standard deviation, skewness and kurtosis, the transitions between different solutions are analyzed in terms of entropy and information length, the total number of statistically distinguishable states that a system passes through in time.

In this paper, we study the problem of controllability of impulsive neutral evolution integrodifferential equations with state dependent delay in Banach spaces. The main results are completely new and are obtained by using Sadovskii's fixed point theorem, theory of resolvent operators, and an abstract phase space. An example is given to illustrate the theory.

Evidence-based medicine (EBM) is in crisis, in part due to bad methods, which are understood as misuse of statistics that is considered correct in itself. This article exposes two related common misconceptions in statistics, the effect size (ES) based on correlation (CBES) and a misconception of contingency tables (MCT). CBES is a fallacy based on misunderstanding of correlation and ES and confusion with 2 × 2 tables, which makes no distinction between gross crosstabs (GCTs) and contingency tables (CTs). This leads to misapplication of Pearson’s Phi, designed for CTs, to GCTs and confusion of the resulting gross Pearson Phi, or mean-square effect half-size, with the implied Pearson mean square contingency coefficient. Generalizing this binary fallacy to continuous data and the correlation in general (Pearson’s r) resulted in flawed equations directly expressing ES in terms of the correlation coefficient, which is impossible without including covariance, so these equations and the whole CBES concept are fundamentally wrong. MCT is a series of related misconceptions due to confusion with 2 × 2 tables and misapplication of related statistics. The misconceptions are threatening because most of the findings from contingency tables, including CBES-based meta-analyses, can be misleading. Problems arising from these fallacies are discussed and the necessary changes to the corpus of statistics are proposed resolving the problem of correlation and ES in paired binary data. Since exposing these fallacies casts doubt on the reliability of the statistical foundations of EBM in general, we urgently need to revise them.

Aortic stenosis (AS) is a prevalent valvular disorder that often requires surgical aortic valve replacement (SAVR) to alleviate symptoms and improve survival. However, the selection of an appropriate prosthetic valve size is crucial to avoid patient-prosthesis mismatch (PPM), which can lead to suboptimal hemodynamic outcomes. Von Willebrand factor (VWF), a key component of hemostasis, has been shown to be altered in AS patients and may contribute to the hemostatic imbalance observed following valve replacement. This prospective study aimed to investigate the impact of PPM on postprocedural VWF levels in patients undergoing SAVR for severe AS. The study included 31 consecutive patients diagnosed with severe AS who underwent SAVR. By focusing on the relationship between PPM and VWF dynamics, this study sought to provide valuable insights into the potential role of VWF as a marker for hemostatic changes associated with PPM, ultimately informing strategies for optimal valve selection and perioperative management to minimize complications.

Pragmatic trials aim to assess intervention efficacy in usual patient care settings, contrasting with explanatory trials conducted under controlled conditions. In aging research, pragmatic trials are important designs for obtaining real-world evidence in elderly populations, which are often underrepresented in trials. In this review, we discuss statistical considerations from a frequentist approach for the design and analysis of pragmatic trials. When choosing the dependent variable, it is essential to use an outcome that is highly relevant to usual medical care while also providing sufficient statistical power. Besides traditionally used binary outcomes, ordinal outcomes can provide pragmatic answers with gains in statistical power. Cluster randomization requires careful consideration of sample size calculation and analysis methods, especially regarding missing data and outcome variables. Mixed effects models and generalized estimating equations (GEEs) are recommended for analysis to account for center effects, with tools available for sample size estimation. Multi-arm studies pose challenges in sample size calculation, requiring adjustment for design effects and consideration of multiple comparison correction methods. Secondary analyses are common but require caution due to the risk of reduced statistical power and false-discovery rates. Safety data collection methods should balance pragmatism and data quality. Overall, understanding statistical considerations is crucial for designing rigorous pragmatic trials that evaluate interventions in elderly populations under real-world conditions. In conclusion, this review focuses on various statistical topics of interest to those designing a pragmatic clinical trial, with consideration of aspects of relevance in the aging research field.

Formaldehyde (HCHO), an indoor volatile organic compound, is seriously harmful to human health. Therefore, green and effective decomposition of HCHO is essential. TiO₂ has been employed for the degradation of HCHO via photocatalytic generation of reactive oxygen species (ROS) (O^2-, ·OH), yet the low specific surface area of crystalline TiO₂ depressed the catalytic performance. Herein, we prepared TiO₂ aerogels with high specific surface area and high porosity by sol-gel method, and added PVA to introduce flexible molecular chains for pore size regulation. The photocatalytic performance test verifies that the pore size of TiO₂ aerogel is one of the important factors for HCHO decomposition. Notably, through the establishment of theoretical model and calculation, we validated that the efficiency of HCHO decomposition is related to the oxygen pressure in the pores of TiO₂ aerogel, and the oxygen pressure is inversely proportional to the pore size. Accordingly, the optimal pore size of TiO₂ aerogel for the photocatalytic HCHO decomposition is 2 nm~10 nm. This study provides a theoretical idea for TiO₂ aerogels in the decomposition reaction of HCHO, which is expected to inspire more breakthroughs in the study of TiO₂ aerogels for green chemistry.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the analysis as well as theoretical considerations concerning to design of gear size ranges. This analysis consists in decomposition of the designed artefact (a gear) according to the rule “from general to details view”. The basics of the object-oriented analysis were formulated. Furthermore, design phases and the objects related to theses phases were discussed. The following models have been considered: hierarchical model, entity-relationship model, data-flow model and object model. Analysis is additionally connected with interactions between particular design phases.

As companies increasingly undergo digital transformation, the role of talent management pro-cesses becomes pivotal in enhancing overall organizational performance. The research addresses the significance of talent management in corporate digital transformation, examining whether variations in the digitalization of these processes can be attributed to company size. A qualitative approach was employed, utilizing a questionnaire, collecting responses from 202 organizations across diverse sectors. Findings reveal disparities in digitalization throughout the talent man-agement process, with pronounced presence in the attracting, selecting, and rewarding phases, but diminishing in deployment and development, further declining in planning. A positive cor-relation between company size and adoption of specific digital platforms was observed. Larger enterprises exhibit greater utilization of digital platforms in talent deployment and development. Moreover, corporate communication tools are consistently utilized in the rewarding phase, irre-spective of company size. These findings offer practical insights for organizations to optimize their digitalization strategies based on their scale, thereby contributing to more effective and tailored digitalization endeavors. The uniqueness of this research lies in its exploration of the in-fluence of company size on the digitalization of talent management processes and its potential to explain variations across different stages of these processes.

This study employs Principal Component Analysis to examine cranial measurements obtained from both extant and fossil specimens spanning 38 species and comprising over 300 individuals within the subfamily Cervinae. Our findings elucidate craniometric distinctions among cervids characterized by varying body sizes and certain evolutionary adaptations. While our results generally corroborate previous assertions regarding the limited craniometric variability among plesiometacarpal deer, they also unveil specific cranial adaptations within certain genera and species. The Principal Component Analysis of craniometric data revealed that giant and large-sized deer display significantly broader ecomorphological diversity in cranial shape compared to small-sized deer. Secondly, small-sized deer exhibit greater uniformity in their cranial shape, appearing densely clustered on the factorial map. Thus, we conclude that body size imposes ecological constraints, limiting the available niches due to eco-physiological factors. The study demonstrates that endemic insular deer do not evolve consistent craniometric features attributable to insular isolation, while the cranial proportions of medium-to-small sized deer delineate a ubiquitous morphological archetype characteristic of numerous cervid taxa spanning diverse phylogenetic lineages and sharing comparable body sizes. This group of "Dama-like" deer, characterized by similar body size, metabolic rates, ecological needs, and cranial morphometry, is referred to here as the fundamental eco-physiological type, typical of warm regions within the Palearctic and Oriental biogeographic realms..

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Sustainable continuous cover forestry is defined and analyzed in several ways. The differential equation representing growth of the basal areas of individual trees, motivated by fundamental biological production theory by Lohmander (2017a), is analyzed and extended in different directions. From the solution of the differential equation, the basal area and the tree diameter are obtained as explicit functions of time. The diameter is a strictly increasing function of time. In the absence of competitors, the diameter increment is shown to be a strictly decreasing function of time. Hence, the diameter increment can also be interpreted as a strictly decreasing function of the diameter. Alternative forms of adjustment of the differential equation, with consideration of competition, are defined. If the competition is strong, with large trees in the vicinity of a particular tree, then the basal area increment, and the diameter increment, are reduced. The growth of a large tree is less sensitive than the growth of a small tree, to competition from other trees. Under strong competition, the basal area increment, and the diameter increment, are strictly concave functions of the size of the tree. The unique maximum of the diameter increment occurs at a higher diameter, if the competition increases. In dynamic equilibrium, the tree size frequency distribution is stationary. If natural tree mortality can be avoided via the harvest strategy, the tree size frequency distribution is a function of the size and competition dependent growth function, and the harvest strategy. Empirical tree size frequency data are used to simultaneously estimate parameters of a size and competition dependent growth function and the applied harvest strategy, via nonlinear optimization. The properties of the estimated growth function are consistent with the corresponding properties of the production theoretically motivated hypothetical function, and the properties of the estimated harvest strategy confirm the corresponding hypotheses. The R2 of the nonlinear regression exceeds 0.97. With access to an empirically estimated equilibrium tree size distribution, it is possible to: 1. Estimate size frequency relevant parameters of tree size and competition dependent growth functions for individual trees. 2. Estimate the applied harvest strategy. 3. Explain and reproduce the empirically estimated tree size equilibrium distribution.

Phytoplankton guilds are commonly characterised by dominance effects, while the main contribution to biological diversity is given by rare species. Here, we analysed the influence of rare species on taxonomic and functional diversity, described by taxa richness and composition, cell size and size abundance relationships in phytoplankton guilds. We explore these relationships at global and regional scales by analysing phytoplankton guilds from five biogeographical regions: Northern Atlantic Ocean (Scotland), South-Western Atlantic Ocean (Brazil), South-Western Pacific Ocean (Australia), Indo-Pacific Ocean (Maldives) and Mediterranean Sea (Greece and Turkey). We have comparatively analysed the phytoplankton taxonomic diversity of the whole dataset and with the datasets obtained by progressively subtracting taxa occurring in the last 1%, 5%, 10% and 25% of both numerical abundance and overall biomass. Globally 306 taxa were identified across five ecoregions with only 27 taxa accounting for the 75% of overall numerical abundance and biomass; almost the 50% of taxa were lost on every step. The removal of 1% most rare taxa significantly affected the phytoplankton size-abundance relationships and body-size structure, strongly impacting on small taxa. The progressive removal of additional rare taxa did not further affect phytoplankton size-abundance relationships and size structure.

This paper presents a comprehensive study based on multiphase seepage and wellbore multiphase flow theories. It establishes a gas intrusion rate calculation model that considers various factors including formation pore permeability, bottomhole pressure difference, drilling fluid rheology, and surface tension. Experiments were conducted to investigate the gas intrusion mechanism under shut-in conditions, and the experimental results were employed to validate the reliability of the proposed gas intrusion rate calculation method. Furthermore, the research explores the transportation rates of single bubbles and bubble clusters in drilling fluid under shut-in conditions. Meanwhile, empirical expressions were derived for the drag coefficient for single bubbles and bubble clusters in the wellbore. These expressions can be used to calculate gas transportation rates for various equivalent radii of single bubbles and bubble clusters. Additionally, a method was developed for calculating the rising velocity of bubble clusters in water based on experimental results. The study reveals that the average bubble size in the bubble cluster is significantly smaller than the size of the single bubble generated from the orifice. When the viscosity of the drilling fluid is low, the bubble cluster transportation velocity exhibits a positive correlation with the average bubble diameter. When the average bubble diameter exceeds 1 mm, the bubble velocity no longer varies with the change in the bubble cluster diameter. The initial bubble size of intrusive gas, the transportation speed of intrusive gas in the wellbore, the gas intrusion rate, and variations of the wellbore pressure after gas intrusion were analyzed. The research results provide theoretical support for wellbore pressure prediction and pressure control under shutdown conditions.

Abstract: A biomaterial is proposed for closing extensive bone defects in the maxillofacial region. The composition of the biomaterial includes high-molecular chitosan, chondroitin sulfate, hyaluronate, heparin, alginate and inorganic nanostructured hydroxyapatite. The purpose of the study is to demonstrate morphological and histological early signs of reconstruction of a bone cavity of critical size. The studies were carried out on 84 white female rats weighing 200-250 g. The study group consisted of 84 subjects in total, 40 in the experimental group and 44 in the control group. In all animals, three-walled bone defects measuring 0.5 x 04 x 05 cm were applied subperiosteally in the region of the angle of the lower jaw and filled in experimental group using lyophilized gel mass of chitosan-alginate-hydroxyapatite (CH-SA-HA). In control animals, the bone cavities were filled with an auto-blood clot after bone trepanation and bleeding. The observation periods are 3.5.7 days, 2.3.4.6.8 and 10 weeks. The control of bone regeneration was carried out using multiple morphological and histological analyses. Results showed that following implantation the chitosan construct actively replaced early-stage defects with the formation of a full-fledged new bone tissue as compared to the control group. Already, by the 7th day morphological analysis showed that formation of spongy bone tissue could be seen. After 2 weeks there was a pronounced increase in bone volume (P<0.01), and at 6 weeks after surgical intervention the closure of the defect was 70-80%, after 8 weeks - 100% without violation of bone morphology with a high degree of mineralization. Thus, the use of modified chitosan after filling eliminates bone defects of a critical size in the maxillofacial region, reveals early signs of bone regeneration, and serves as a promising material in reconstructive dentistry.

Earnings management and financial distress are two critical facets of financial management in corporations that have lately been the focus of thorough research from both scholars and practitioners. The purpose of the research is to evaluate the influence of financial distress on the earnings management of companies listed at the NSE during the pre- and post-COVID eras. Multiple linear regression was applied in this study to examine the causal association between earnings management and financial distress. To assess the effect of financial distress on earnings management, the study analyzed data from 37 listed companies during the pre-COVID and post-COVID periods. The methodology also takes into account control factors like firm size, GDP, and inflation. The pre-COVID research indicates a significant positive correlation between financial strain and earnings management. In contrast, the correlation between financial distress and earnings management is not statistically significant in the post-COVID analysis. However, research shows that firm size has a statistically significant negative influence on managing earnings. The results of this study show that smaller firms are more inclined to engage in earnings management during the post-COVID era than bigger ones.

Debris flows have generated major disasters worldwide due to their great destructive capacity, which is associated with their high energy levels and short response times. To achieve an adequate risk management of these events, it is necessary to define as accurately as possible the different hazard levels to which the territory is exposed. This article develops a new methodology to estimate this hazard based on the hydrodynamic characteristics of the flow and the granulometry of the sediments that can be mobilized by the flow. The hydrodynamic characteristics of the flow are determined through a mathematical modeling that considers the rheology of non-Newtonian flows and the different volumes of sediments that could be transported during events corresponding to different return periods. The proposed methodology was implemented in the Jamundí River basin (Colombia). The results obtained indicate that in the upper part of this basin there is a low hazard level, while in the lower part of the basin approximately 15% of the affected territory has a medium hazard level and the remaining 85% has a low hazard level. The methodology developed is simple to implement but technically rigorous since it considers all relevant aspects in the generation of debris flows.

Why do the eyes remain comparatively large whereas the cornea is reduced in most troglobiont mysids? Are there any important organ size-dependent functions served by non-visual eye rudiments? This issue was approached by measuring eye structures in five troglobiont species of Mysida and two Stygiomysida compared with 14 troglophile and 49 trogloxene Mysida species. The Organ of Bellonci (OB) was found in all Mysida and as first records also in Stygiomysida. The length of OBs increased with individual body length and eye length in four examined species: from postnauplioid larvae to adult stage in a troglophile and a trogloxene mysid species examined; and from juveniles to adults in a troglobiont mysid and a troglobiont stygiomysid. At the interspecific level, eye length was on average 26% shorter at a given body length while the OB was 40% longer at a given body length and 54% longer at a given eye length, respectively, in adult troglobionts compared with trogloxene mysids. The OB is clearly proliferating while the cornea is reduced in troglobionts. This points to sensory functions (possibly together with other functions). The sensory pore organ was found in all 15 Mysida species whose eyes were mounted on slides, and a first record of this organ was also found in Stygiomysida.

The paper presents the first retrievals of clean snow properties using spaceborne hyperspectral The Environmental Mapping and Analysis Program (EnMAP) observations. The location close to the Dome C in Antarctica has been selected. At this location the atmospheric effects except molecular light scattering and absorption are weak and the simplified atmospheric correction scheme can be applied. The ice grain size, snow specific surface area and snow spectral and broadband albedos have been retrieved using single view EnMAP measurements. In addition, we propose the technique to retrieve trace gas concentrations (e.g., water vapor, ozone) from EnMAP observations over the snow surfaces. Close correspondence of satellite and ground measured parameters has been found.

Comminution is a very important and result-determining step in mineral processing. This is because further downstream processes in the beneficiation chain depend entirely on it. Comminution includes the blasting, crushing, and grinding of ore to liberate valuable mineral particles. It consumes most of the energy used in mineral processing plants with grinding using up to 50% of the provided energy. Tumbling mills are an old technology that is still commonly used for grinding. One of the most used tumbling mills is the ball mill. This paper reviews different types of grinding media that have been developed and improved over the years and their properties. Also reviewed are the effects of grinding media on various aspects such as energy consumption, mill efficiency, minerals liberation and grinding rate. A comparison of the grinding media is given together with the knowledge gaps that still need to be bridged to improve the quality and performance of grinding media used in ball mills. Despite various research conducted on ball mills, the grinding process is still a very energy inefficient process. This creates a great opportunity for further research to improve the process because just a slight improvement in the process efficiency significantly reduces the production costs and provides a lot of environmental benefits.

The history of agricultural terraces dates back to agricultural society; and throughout history, they have enabled agricultural activities to be carried out on lands with irregular relief. They have also served as an essential element of rural landscapes due to their architectural features, building materials, and techniques, as well as the landscapes they create. Furthermore, terraces also contribute to soil conservation by preventing erosion, adding organic matter to the soil, and harvesting rainwater. The significance of agricultural terraces in the cultural landscape has triggered the need to define and classify them. In this regard, agricultural terraces across many different locations have found their place on the List of Globally Important Agricultural Heritage Sites (GIAHS) and UNESCO cultural heritage lists. In the present study, the agricultural terraces of the Erikli neighborhood of the Uzundere district were mapped through surveys, drone shots, and orthophotos, and analyzed based on the size and density indices previously used in the classification of Alpine terraces. The study is important in terms of demonstrating the use of drone technology in mapping agricultural terraces. The results of the study revealed that 51.6% of the agricultural terraces in the study area had very steep slopes and 22195 meters of total stone wall length, the average density index was 523.29 m/ha, and 76.4% of the terraces were meso and macro in character. Moreover the study shows that the terraces in the region are more susceptible to deterioration.

This review focuses on developments that quantify grain quality with a range of spectral sensors in an on-farm setting. If the application of sensor technologies were expanded and adopted on-farm, growers could identify the impact and manage the harvesting operation to meet a range of quality targets and provide an economic advantage to the farming enterprise.

In order to understand the evolution of multicellularity, we must understand how and why selection favors the first steps in this process: the evolution of simple multicellular groups. Multicellularity has evolved many times in independent lineages with fundamentally different ecologies, yet no work has yet systematically examined these diverse selective drivers. Here we review recent developments in systematics, comparative biology, paleontology, synthetic biology, theory, and experimental evolution, highlighting ten selective drivers of simple multicellularity. Our survey highlights the many ecological opportunities available for simple multicellularity, and stresses the need for additional work examining how these first steps impact the subsequent evolution of complex multicellularity.

The rearing temperature of the immature stages can have a significant impact on the life-history traits and the ability of adult mosquitoes to transmit diseases. This review assessed published evidence of the effects of temperature on the immature stages, life-history traits, insecticide susceptibility, and expression of enzymes in the adult Anopheles mosquito. Original articles published through 31 March 2021 were systematically retrieved from Scopus, Google Scholar, Science Direct, PubMed, ProQuest and Web of Science databases. After applying eligibility criteria, 29 studies were included. The review revealed that immature stages of Anopheles arabiensis were more tolerant (in terms of survival) to a higher temperature than An. funestus and An. quadriannulatus. Higher temperatures resulted in smaller larval size and decreased hatching and pupation time. The development rate and survival of Anopheles stephensi were significantly reduced at a higher temperature than a lower temperature. Increasing temperatures decreased the longevity, body size, length of the gonotrophic cycle and fecundity of Anopheles mosquitoes. Anopheles mosquitoes exposed at 18° or 30 °C had a higher risk of dying compared to those exposed at 25 °C. Increasing temperature also significantly increased NOS expression and decreased insecticide toxicity. Both extreme low and high temperatures affect Anopheles mosquito development and survival. Climate change could have diverse effects on Anopheles mosquitoes. There seems to be inconclusive evidence of the effects of temperature on the development and survival of Anopheles species, and more studies are needed to clarify this relationship.

Background The link between age at marriage and first birth in explaining completed family size is not always direct, due to heterogeneity in circumstances, that compel individual women to marry or initiate childbearing at a particular age. We analyzed data for 1020 women aged 45-49 in 2014 of the 1965-1969 birth cohort from the 2013-14 Zambia Demographic and Health Survey (ZDHS). Methods We fitted a bivariate and multivariate multinomial logistic regression to establish the relationship between a mother’s age at first marriage and at first birth on completed family size (CFS). Chi-square test of proportions measuring differences in proportions and relative risk ratios (RRR) with confidence intervals at 95% are reported. Results Our results show that the average CFS was 6.7 (95% CI: 6.5 – 6.9) among women completing their reproductive span in 2014 with mean age at first marriage and birth being 18.3 years (95% CI: 18.0 – 18.5) and 18.9 years (95% CI: 18.7 – 19.1) respectively. Women marrying at younger ages and having their first birth at younger ages were more likely (RRR: 1.187; 95% CI: 1.138-1.239 and RRR: 0.195; 95% CI: 0.074-0.511 respectively) to have higher CFS than their compatriots that initiated both marriage and childbearing at or after age 22 controlling for covariates as presented in the controlled model. The independent effects model shows that the risk of having 1-3 children compared to 6 or more children was lower (RRR: 0.073; 95% CI: 0.009-0.611; RRR: 0.136; 95% CI: 0,046-0.402 and RRR: 0.421; 05% CI: 0.135-1.312) for women whose ages at first marriage were <15, 15-18 and 19-21 respectively relative to 22+. Women with 1-3 children were 2.5 times more likely to use contraception than women with 6 or more children. Conclusion Having no education, being a rural resident and having a medium household wealth all increase the risk of having higher CFS. Women that marry before age 19 have a higher likelihood of having 6 or more children by the end of their reproductive period. The study concludes that apart from a woman’s age at first marriage and first birth, a complex network of factors interact to determined CFS.

We evaluated the change in water dispersibility of lactic acid bacteria (LAB, Enterococcus faecalis KH2) upon powderization and its influence on their efficacy. When cultured LAB are washed, heat-killed, and powdered, adhesion between LAB occurs and they form aggregation (non-treated LAB, n-LAB). However, a dispersed LAB (d-LAB) powder with less aggregates can be prepared by treating them with a high-pressure homogenizer and adding an excipient during powdering. n-LAB or d-LAB was administered to mice and the Peyer's patches in the small intestine were observed. n-LAB administration showed a high amount of aggregated LAB drifting in the intestinal mucosa, whereas d-LAB reached the Peyer's patches and was taken up into the Peyer's patches. Evaluation in a mouse influenza virus infection model showed that d-LAB was more effective than n-LAB in influenza yield of bronchoalveolar lavage fluids (BALFs) on day 3 post-infection, neutralizing antibody titers of sera and influenza virus-specific IgA in the feces on day 14 post-infection. Thus, the physical properties of LAB affect their efficacy; controlling their water dispersibility can improve their effectiveness.

The fast spread of COVID-19 constitutes a worldwide challenge to the public health, educational, and trade systems, affecting the overall wellbeing of human societies. The high transmission and mortality rates of this virus, and the unavailability of a vaccine or treatment, resulted in the decision of multiple governments to enact measures of social distancing. Thus, it is of general interest to consider the validity of the proposal for keeping a social distancing of at least 2 m from other persons to avoid the spread of COVID-19. The exposure to the bioaerosol can result in the deposition of the pathogen in the respiratory tract of the host causing disease and an immunological response. In the atmospheric context, the work evaluates the effect of aerodynamic diameter (size) of particles in carrying RNA copies of the novel coronavirus. A SARS-CoV-2 carrier person talking, sneezing, or coughing at distance of 2 m can still provide a pathogenic bioaerosol load with submicron particles that remain viable in air for up to 3 hours for exposure of healthy persons near and far from the source in a stagnant environment. The deposited bioaerosol creates contaminated surfaces, which if touched can act as a path to introduce the pathogen by mouth, nose, or eyes and cause disease.

Corporate governance is widely suggested by economists and regulators as a solution to reduce agency problems and improve firm performance. However previous studies have failed to generate consistent results. Using a dynamic panel system GMM estimator to alleviate endogeneity concerns we determine the effect of corporate board structure on the performance of a panel of 1265 Chinese firms listed on the Shanghai and Shenzhen stock exchanges from 2010 to 2016. We compare the dynamic system GMM estimator to some commonly used estimators; ordinary least squares (OLS), fixed effects (FE) and the dynamic OLS, and show that these estimates are biased due to endogeneity. The dynamic system GMM estimator incorporates the dynamic nature of internal governance choices to provide valid and powerful instruments that address unobserved heterogeneity and simultaneity. Our results show support for the board model corporate governance mechanism. We find that board size is positive and significantly related to both return on assets and total net profit margin. In addition board independence is positive and significantly related to return on assets but insignificantly related to total net profit margin. Duality was found to have a negative but statistically insignificant relation with firm performance.

Knowledge of a lasers beam’s profile throughout a laser system and experiment can help immensely in diagnosing laser problems and assisting in beam alignment and focusing at a sample. Obtaining such profiles is a trivial task in the ultraviolet-visible wavelength range but more challenging with near-infrared to infrared beams. Scientific grade bolometer arrays, suitable for such a task, do exist but are extremely costly, relatively large and have a large pixel size, of the order of 80 μm, which is adequate for profiling larger beams but poses an issue when trying to profile sub 100 μm beams for example at a focal point. This communication identifies a micro-bolometer array for near- to mid-infrared laser beam profiling, which is extremely low cost. In addition, the device is very compact, enabling use in confined spaces, and has a small, 12 μm, pixel size permitting the profiling of focused laser beams. The best scientific grade device identified has a pixel size of 17 μm. This device is a powerful tool for infrared laser spectroscopists, reducing the time required to measure the spot size of beams and to achieve spatial overlap of multiple infrared beams as used in two-dimensional infrared spectroscopy, saving many hours of setup time. The use of the bolometer array as a spectrographic detector and probe of long-term beam drifts is also demonstrated.

Vanadium titano-magnetite is a significant resource in China, and in this study, we characterize its isothermal reduction mechanisms in the mixture of H₂, CO, and N₂ where the variables considered here include reduction time, reduction temperature, gas composition, and pellet size. The kinetics of the reduction process are mainly studied, which follows a shrinking core model. The results indicate that the reduction degree of oxidized VTM pellets increases with the increase of reduction time, reduction temperature but decreases with the increase of pellet size. Moreover, we found that an increase of H₂/(H₂+CO) ratio induces an increase of the reduction degree. Then the transformation of main Ti-bearing mineral phases is discussed, and the most probable reaction mechanism is revealed. In the whole reduction process, the kinetic results confirm the existence of an early stage and a latter stage, which are controlled by interface chemical reaction and diffusion, respectively. Furthermore, the results show that the diffusion-control step can be observably shortened with the decrease of pellet size because a thinner product layer is formed during the reduction process. Our study thus provides a valuable technical basis on the VTM industrial application.

There are no studies that quantitatively compare life histories among scorpion species. Statistical procedures applied to 94 scorpion species indicate that those with larger bodies do not necessarily have larger litters or longer life cycles, opposite to some theoretical predictions.

The objective of this study was to investigate successional changes in water flow as a result of changes in soil hydraulic properties after crop abandonment under drought and non-drought conditions, and under water uptake by co-occurring perennial plant species to clarify the observation that typical perennial grass species are seldom observed in abandoned fields. Soil hydraulic properties were measured in croplands which had been abandoned for different periods (2, 9, and 18 years from abandonment) and in a grazed grassland site. Hydrological processes in the soil profiles were simulated with soil hydraulic properties under drought and non-drought summer conditions with water uptake from perennial grass species Suction in the surface soils increased with the period of abandonment, with this trend being particularly obvious in a drought year. Available water appears to be restricted in the later successional stage of abandoned fields and in grazed grassland for plants that have drought tolerance. Dry soil and climate conditions are important factors determining the intrusion of the typical perennial grass, S. krylovii, into degraded abandoned fields. This abiotic interaction between soil hydraulic properties and climate conditions may play an important role for plant succession in abandoned cropland.

The aim of this study is to introduce a novel method which can separate sand or gravel dominated bed load transport in rivers with mixed-size bed material. In engineering practice, the Shields-Parker diagram could be used for such purposes, however, the method has certain applicability limits, due to the fact that it is based on uniform bed material and provides information rather on river-scale, instead of reach or local scale. When dealing with large rivers with complex hydrodynamics and morphodynamics the bed load transport modes can also indicate strong variation even locally, which requires a more suitable approach to estimate the locally unique behavior of the sediment transport. Here, we suggest that the decision criteria utilizes the shear Reynolds number (Re*). The method was verified against field and laboratory measurement data, both performed at non-uniform bed material compositions. The comparative assessment of the results show that the shear Reynolds number based method operates more reliably than the Shields-Parker diagram and it is expected to predict the sand or gravel transport domination with a < 5% uncertainty. The introduced results can greatly contribute to the improvement of numerical sediment transport modeling as well as to the field implementation of bed load transport measurements.

In this study, we applied a central composite design to estimate independent variables and establish optimal conditions of filtration rate and feces production that enhance filtration of suspended organic matter by the freshwater mussels Sinanodonta woodiana. The results indicated that statistical design methodology offers an efficient and feasible approach for high filtration and low feces production condition optimization. The proposed model equation takes into account the quantitative effect of variables and also the influence of interactions among variables on mussel filtration rate. Under the optimal experimental conditions (mussel size, 13.0 ± 0.2 cm; water current, 17.5 L/h), the experimental filtration rate of 4.47 ± 1.82 L/mussel/h showed a degree of correspondence with the predicted value of 8.4 L/mussel/h, which verified the practicability of this optimum strategy.

The main objective of this paper is to find a close link between the adaptive level of significance, presented here, and the sample size. We, statisticians, know of the inconsistency, or paradox, in the current classical tests of significance that are based on p-value statistics that is compared to the canonical significance levels (10%, 5% and 1%): "Raise the sample to reject the null hypothesis" is the recommendation of some ill-advised scientists! This paper will show that it is possible to eliminate this problem of significance tests. The Bayesian Lindley's paradox – "increase the sample to accept the hypothesis" – also disappears. Obviously, we present here only the beginning of a possible prominent research. The intention is to extend its use to more complex applications such as survival analysis, reliability tests and other areas. The main tools used here are the Bayes Factor and the extended Neyman-Pearson Lemma.

Cancer-specific monoclonal antibodies (CasMabs) that recognize cancer-specific antigens with in vivo antitumor efficacy are innovative therapeutic strategies for minimizing the adverse effects. We previously established a cancer-specific anti-human epidermal growth factor receptor 2 (HER2)monoclonal antibody (mAb), H₂Mab-250/H₂CasMab-2. In flow cytometry and immunohistochemistry, H₂Mab-250 reacted with HER2-positive breast cancer cells but did not show the reactivity to normal epithelial cells. In contrast, a clinically approved anti-HER2 mAb, trastuzumab, strongly recognizes both breast cancer and normal epithelial cells in flow cytometry. The human IgG₁ version of H₂Mab-250 (H₂Mab-250-hG₁) possesses compatible in vivo antitumor effects against breast cancer xenografts with trastuzumab despite the lower affinity and effector activation than trastuzumab in vitro. This study compared the antibody-dependent cellular cytotoxicity (ADCC) and complement-dependent cellular cytotoxicity (CDC) between H₂Mab-250-hG₁ and trastuzumab. Both H₂Mab-250-hG₁ and trastuzumab showed ADCC activity against CHO/HER2 and breast cancer cell lines (BT-474 and SK-BR-3) in the presence of human natural killer cells. Some tendency was observed that trastuzumab showed a more significant ADCC effect compared to H₂Mab-250-hG₁. Importantly, H₂Mab-250-hG₁ exhibited superior CDC activity in these cells compared to trastuzumab. Similar results were obtained in mouse IgG_2a types of both H₂Mab-250 and trastuzumab. These results suggest the different contributions of ADCC and CDC activities to the antitumor effects of H₂Mab-250-hG₁ and trastuzumab and indicate the future direction for the clinical development of H₂Mab-250-hG₁ against HER2-positive tumors.

Present experimental study assesses the mechanical properties of glass/carbon/glass hybrid composite laminates after exposure to moisture and elevated temperatures for extended periods. The top and bottom layers of the hybrid laminates are glass fiber reinforced and the middle layer is carbon fiber reinforced with the matrix specified as a polymer material. The hybrid laminates were manufactured using the resin transfer molding method and their compressive and tensile properties were determined using a tensile testing machine. The material parameters such as the storage modulus, the loss modulus, and the damping factors of the laminates were identified using dynamic mechanical analysis as a function of the temperature and the vibration frequency. The experimental results on compressive and tensile properties revealed slight variations when the hybrid laminates were kept at low temperatures for extended periods. This might occur due to the increasing molecular cross-linking of the polymer network. As the temperature increased, compressive, tensile, storage modules, loss modulus, and damping factors decreased. This might occur due to the increasing mobility of the binder material. Particularly, the highest stiffness parameters were obtained on -80°C/GCG (Glass/Carbon/Glass) laminates due to the presence of beta transition on the glassy region. The relationships between the glass transitions and the targeted frequencies were characterized. The values of the glass transition shift towards higher temperatures as the frequency increases. This might occur due to a reduction in the gaps between the crosslinking of the epoxy network when the frequency increases. The accuracy of the storage modulus results was compared with the empirical models. The model based on the Arrhenius law provided the closest correlation. Meanwhile, another model was observed that was not accurate enough to predict when gamma and beta relaxations occur under a glassy state.

We previously developed a highly sensitive and specific anti-PDPN mAb, LpMab-23 (mouse IgG1, kappa). In this study, we produced a humanized IgG1 version (humLpMab-23) and its defucosylated form (humLpMab-23-f) of an anti‑PDPN mAb to potentiate the ADCC activity. The humLpMab-23 could recognize PDPN‑overexpressed Chinese hamster ovary (CHO)-K1 (CHO/PDPN) and PDPN-positive PC-10 and LN319 cells by flow cytometry. Furthermore, we found that humLpMab-23-f exerted ADCC and complement-dependent cytotoxicity against CHO/PDPN, PC-10 and LN319 cells in vitro and exhibited potent antitumor activities in the xenograft models. These results indicated that humLpMab-23-f could be useful for an antibody treatment regimen for PDPN-positive human cancers.

The focus of the current research indicates a new Bianchi type-V anisotropic, homogeneous astrophysical model with modified theory of f(R, T) gravity and Λ(t), time-dependent cosmological constant. The significant effect of the model is that the field equations solutions find using a time-dependent quadratic deceleration parameter. We observed anisotropy parameter remains constant both in the belated universe and early universe. The deportment of the equation of state (EOS) parameter, pressure, and energy density, cosmological constant and other parameters are also discussed. This cosmological model indicated the possibility of an accelerating universe with negative pressure, such as a universe dominated by dark energy. Om(z) diagnostic test suggested that the universe starts with quintessence nature and ends as a phantom model. Also, energy conditions of this model are represented here to ensure the model is physically reasonable and based on observations.

Metallo-β-lactamases (MBLs) are a group of Zn(II)-dependent enzymes that pose a major threat to global health. They are linked to an increasing number of multi-drug resistant bacterial pathogens, but no clinically useful inhibitor is yet available. Since β-lactam antibiotics, which are inactivated by MBLs, constitute ~65% of all antibiotics used to treat infections, the search for clinically relevant MBL inhibitors is urgent. Here, derivatives of a 2-amino-1-benzyl-4,5-diphenyl-1H-pyrrole-3-carbonitrile (1a) were synthesised and their inhibitory effects assessed against representatives of each of the three subgroups of MBLs (B1, B2, B3). Several compounds are potent inhibitors of each MBL tested, making them excellent candidates for the development of broad-spectrum drug leads. In particular, compound 5f is highly potent across the MBL subfamilies, with Ki values in the low µM range. Furthermore, this compound also dis-plays synergy in combination with antibiotics such as penicillin G, cefuroxime or meropenem. This molecule thus represents one of the most promising compounds developed yet to combat MBLs.

Converting natural language into machine language that can be recognized by distributed systems is the core challenge of intelligent interactive interfaces and human-machine dialogue systems. The human-machine interface interaction of large distributed SCADA measurement and control system is tedious and the operation and maintenance cost is high, so it is significant to design an intelligent natural language interaction interface for distributed measurement and control system. In this paper, we design the intermediate language format of SCADA system, i.e., Key-value logic form, and then formulate the Text2SCADA framework and propose the TICS algorithm and SDPA algorithm, the former adopts the keyword extraction and cosine similarity optimization algorithm to complete the structured extraction of natural language for basic natural language instructions, and the latter adopts the keyword extraction and cosine similarity optimization algorithm to complete the structured extraction of natural language for relatively The latter one adopts the algorithm of dependent syntactic analysis for the structured representation of natural language instructions with relatively complex natural language instructions. Based on the above algorithms, a lightweight information extraction model based on DGCNN and probabilistic graph ideas is constructed, aiming to enhance the scientific generalization ability of the framework on unknown instruction sets. The experimental results show that the proposed intelligent natural language interface can better solve the human-machine interface interaction problem of distributed SCADA measurement and control system. The average accuracy, recall and F-value of instruction parsing reach 89.27\%, 89.28\% and 89.27\%, respectively. The average response time is 1.593 s. Especially, it provides a more convenient means of interaction for industrial and agricultural information control.

Favipiravir is a broad-spectrum inhibitor of viral RNA-dependent RNA polymerase (RdRp) currently being used to manage COVID-19 in several countries. By acting as a substrate for RdRp, favipiravir gets incorporated into the nascent viral RNA and prevents strand extension. A high mutation rate of SARS-CoV-2 RdRp may facilitate antigenic drift as an answer to the host immune response, thereby generating resistance of virus to favipiravir. Therefore, it is extremely crucial to predict potential mutational sites in the RdRp and the emergence of structural modifications contributing to drug resistance. Here, we used high-throughput interface-based protein design to generate >100,000 designs and identify mutation hotspot residues in the favipiravir-binding site of RdRp. Several mutants had lower binding affinities to favipiravir, out of which hotspot residues with a high propensity to undergo positive selection were identified. The results showed that the designs retained an average of 97 to 98% sequence identity, suggesting that SARS-CoV-2 can develop favipiravir resistance with just a few mutations. Notably, we observed that out of 134 mutations predicted designs, 63 specific mutations were already present in the CoV-GLUE database, thus attaining ~47% correlation match with the clinical sequencing data. The findings improve our understanding of the potential signatures of adaptation in SARS-CoV-2 against favipiravir and management of COVID-19. Furthermore, they can help develop exhaustive strategies for robust antiviral design and discovery.

Exercise affects various organs. However, its effects on nutrient digestion and absorption in the intestinal tract are not well understood. A few studies have reported that exercise training in-creases the expression of carbohydrate digestion and absorption molecules. Exercise was also shown to increase the concentration of blood glucagon like peptide-2(GLP-2), which regulates carbohydrate digestion and absorption in small intestinal epithelium. Therefore, we investigated the effects of exercise on intestinal digestion and absorption molecules and the levels of GLP-2. 6-wk-old of male mice were divided into 2 groups; sedentary (SED) and low-intensity exercise (LEx). LEx mice were required to run on a treadmill (12.5 m/min, 60 min), whereas SED mice rested. All mice were euthanized 1 h after exercise or rest and plasma, jejunum, ileum, and colon were sampled. Samples were analyzed using EIA and immunoblotting. The levels of plasma GLP-2 and the expression of the GLP-2 receptor, sucrase-isomaltase (SI), and glucose transporter (GLUT2) in the jejunum were increased in LEx group. We showed that acute low-intensity exer-cise affects the intestinal carbohydrate digestion and absorption molecules via GLP-2. Our results suggest that exercise might provide new benefits to the small intestine for people with intestinal frailty.

COVID-19 has emerged as deadly pandemic worldwide with no vaccine or suitable antiviral drugs to prevent or cure the disease. Because of the time-consuming process to develop new vaccines or antiviral agents, there has been a growing interest in repurposing some existing drugs to combat SARS-CoV-2. Vitamin D is known to be protective against acute respiratory distress syndrome (ARDS), pneumonia and cytokine storm. Recently it has been used as a repurposed drug for the treatment of H5N1 virus-induced lung injury. Circumstantial evidences indicate that people with low level of vitamin D are more susceptible to SARS-CoV-2. Although, vitamin D was suggested to interfere with viral replication, its interaction with any SARS-CoV-2 protein is unexplored yet. Beside this, ivermectin, a well-known anti-parasitic agent, exhibits potent anti-viral activities in vitro against viruses such as HIV-1 and dengue. Very recently, ivermectin has been found to reduce viral load of SARS-CoV-2 in vitro. We have analyzed available structures of SARS-CoV-2 proteins to identify probable binding partner(s) of vitamin D and ivermectin through knowledge-based docking studies and figured out possible implication of their binding in SARS-CoV-2 infection. Our observations suggest that the non-structural protein nsp7 possesses a potential site to house 25-hydroxyvitamin D3 (VDY) or the active form of Vitamin D, calcitrol. Binding of vitamin D with nsp7 likely to hamper the formation of nsp7-nsp8 complex which is required to bind with RNA dependent RNA polymerase (RdRP), nsp12 for optimal function. On the other hand, potential binding site of ivermectin has been identified in the S2 subunit of trimeric spike(S) glycoprotein of SARS-CoV-2. We propose that deeply inserted mode of ivermectin binding at three inter-subunit junctions may restrict large scale conformational changes of S2 helices which is necessary for efficient fusion of viral and host membrane. Our study, therefore, opens up avenues for further investigations to consider vitamin D and ivermectin as potential drugs against SARS-CoV-2.

Oxygen extraction fraction (OEF), the fraction of oxygen that tissue extracts from blood, is an es-sential biomarker for directly assessing tissue viability and function in neurologic disorders. For quantitative mapping of OEF, an integrative model of quantitative susceptibility mapping and quantitative blood oxygen level-dependent magnitude (QSM+qBOLD or QQ) was recently pro-posed. However, QQ assumes Gaussian noise in both susceptibility and multi-echo gradient echo (mGRE) magnitude signals for OEF estimation. This assumption is unreliable in low sig-nal-to-noise ratio (SNR) regions like disease-related lesions, risking inaccurate OEF estimation and potentially impacting clinical decisions. Addressing this, our study presents a novel multi-echo complex QQ (mcQQ) that models realistic noise in mGRE complex signals. The proposed mcQQ was implemented using a deep learning framework (mcQQ-NET) and compared with the existing deep learning-based QQ (QQ-NET) in simulations, ischemic stroke patients, and healthy subjects. Both mcQQ-NET and QQ-NET used identical training and testing datasets and schemes for a fair comparison. In simulations, mcQQ-NET provided more accurate OEF than QQ-NET. In the sub-acute stroke patients, mcQQ-NET showed a lower average OEF ratio in lesions relative to unaf-fected contralateral normal tissue than QQ-NET. In the healthy subjects, mcQQ-NET provided uniform OEF maps, similar to QQ-NET, but without unrealistically high OEF outliers in areas of low SNR. Therefore, mcQQ-NET improves OEF accuracy by better reflecting realistic data noise characteristics.

Plant biomass could become a new world-class "currency" because almost everything can be made of it: fuels, foods, feeds, constructing materials, furniture, etc. Currently, growing biomass for energy needs is particularly relevant in so complicated socioeconomical situation. There are important its productivity and the lowest possible ecological footprint. Can increasing crop biodiversity address these challenges? A field experiment was started at the Vytautas Magnus University Agricultural Academy in 2020-2022. Maize, hemp and faba bean were grown as single, binary and ternary crops to determine its effect on soil properties. Studies have shown that most intercrops failed to stabilize soil aggregate composition, NPK levels and pH, and enzyme urease activity. Binary maize-hemp and the ternary crops reduced the amount of the main macroelements in the soil the most because of the highest yields, which were removed from the fields. Regardless of the ecological services provided by faba beans, biomass removal leads to degradation of most soil properties and making the soil vulnerable to erosion. In the future, the cultivation of such multicrops should be investigated under conditions of more abundant fertilization or the effect of green manure should be used by increasing the number of fast- and short-growing interior plant species in the cultivation.

Dams fragment stream habitat and fishways around dams typically serve few species that are strong swimmers or jumpers. We test a prototype wetted ramp designed to allow upstream passage of small-bodied fishes while blocking upstream movement of invasive sea lamprey in the Laurentian Great Lakes. We tested short, smooth ramps with 5-10 mm water depth in various combinations of ramp angle, water flow and swim channel width with the aim to selectively block adult migrating sea lamprey while passing sub-adult white suckers (Catostomus commersonii) and creek chubs (Semotilus atromaculatus). Sea lamprey easily passed a 0.75 ramp at 5 angle, but very few individuals passed a similar ramp at 10 angle and none passed a longer ramp at the 5 angle. Limiting the amplitude of tailbeats in a narrow channel did not hamper lamprey or the other species. Greater water flow, and thereby greater immersion depth on the ramp fostered passage for all species. Smaller-bodied individual of creek chubs and white suckers performed best on the ramp. We show that wetted ramps could be incorporated into fishways at low-head dams to aid passage of smaller-bodied fishes while also blocking the spawning migration of adult sea lamprey.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the synthesis as well as theoretical considerations concerning to design of gear size ranges. The synthesis consists in composition (aggregation) of single details into units – according to the rule: “from details up to general view”. The basics of the object-oriented synthesis were formulated. Furthermore, the consecutive stages of synthesis were formulated. The interactions between these stages were discussed. Some aspects were described in details e.g.: creation of interfaces for performance of the embodiment phase the designed artefact via CAD system drawing with specification (dimensions are still parametrically set). The final step of the procedure is creation of so called substantial (concrete) form of artifacts i.e. final assignment of dimensions which stored in the special data base. The final stage of the design process is issuing of technical documentation (technical drawings) created automatically via CAD system. The considerations are terminated by the list of advantages connected with the object-oriented approach to design (in comparison to the traditional way).

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

Recently perovskite solar cells have been paying attention of researchers. This comes from their high efficiency and stability. In this work, the change of some Optical and Electrical Properties of BaxFe(1-x)TiO4 thin films due to the change of the nanocrystal spacing and size were studied. A simple theoretical model based on the string theory was utilized to explain some of these empirical relations. The empirical results obtained indicated that an increase in the efficiency of the nano solar cell requires the energy gap to be narrow. Decreasing the nanocrystal size and spacing caused the energy gap to become narrower. The energy gap decreases also upon increasing the absorption coefficient and decreasing the transmission. This also requires increasing the conductivity and the magnetic permeability. The increase of the nanocrystal spacing decreases the absorption coefficient, electrical conductivity, and magnetic permeability, while it causes the transmission to increase. All these changes are explained using a simple string model beside Newton's laws. The capability of the string theory to explain this Nano quantum behavior comes from the fact that the string theory, like quantum theory, recognizes both the particle and the wave nature of the Nano system.

Chromosome segregation in female germ cells and early embryonic blastomeres is known to be highly prone to errors. The resulting aneuploidy is therefore the most frequent reason for termination of early development and embryo loss in mammals. And when compatible with embryonic and foetal development, aneuploidy leads into severe developmental disorders. The main surveillance mechanism, essential for protection of cells against aneuploidy, is the Spindle Assembly Checkpoint (SAC). And although all eukaryotic cells are perhaps able to mount SAC response, it is not clear, whether this pathway is active in all cell types, including blastomeres of early embryos. In this review, we will summarize and discuss the published literature with regards to mechanisms controlling chromosome segregation in early embryos. Our conclusion is that early embryos show limited capabilities to react to chromosome segregation defects, which might, at least partially, explain the widespread problem of aneuploidy during early development.

This study empirically analyzes how R&D expenditures affect firm value using a regression model for listed firms in Shandong Province, China. The dependent variable is measured by To-bin Q, which measures firm value, and the experimental variable among the independent varia-bles is R&D expenditure. In addition, financial leverage and firm size, which have been found to have a significant impact on firm value in previous studies, were selected as control variables. The study sample consisted of 554 data points analyzed over a nine-year period from 2010 to 2018. Without controlling for variables that affect firm value, the correlation analysis shows that R&D expenditures of listed firms in Shandong Province, China have a significant positive impact on firm value at the 1% level. For a more precise analysis, we ran a multivariate regression analysis controlling for other variables that affect firm value and found that R&D expenditure has a significant positive impact on firm value at the 1% level. These findings suggest that man-agers of listed companies in Shandong Province, China, need to actively engage in R&D activi-ties to increase firm value. Companies in Shandong Province, China, are currently experiencing very strong growth, and this study, which shows that R&D is the key to increasing the value of these companies, can help companies in Shandong formulate their business strategies.

Aedes aegypti is the main vector of various arboviruses including dengue, yellow fever, Zika and chikungunya virus. This mosquito species originated in Africa but has a wide range of distribution, colonising various ecological zones. The transmission dynamics of arboviruses depends on environmental factors, but also on mosquito life history traits including development time, fecundity, and longevity. The objective of the current study was to assess the Aedes aegypti immature development time, adult longevity, fecundity and body variation from different sampling localities. Aedes aegypti mosquitoes were collected as eggs from different geographical zones and cohorts of mosquitoes were reared in standardized laboratory conditions to assess the life history traits parameters. Emerged adults were discriminated into morphotypes according to the density of white scales on the first abdominal tergite. The means of fecundity, longevity, development time and body size were assessed, and linear models were fitted to the traits parameters to assess the effects of other covariables. Average Aedes aegypti development time was estimated to 7.35 days; 7.40 days; 6.98 days and 7.40 days respectively for Dori, 1200 logements, Bobo-Dioulasso and Toudweogo. The fecundity did not vary across study sites and was not associated with the body size. The longevity varied according to the study sites with the mosquitoes from Bobo-Dioulasso having the longest longevity while the shortest longevity was found at Dori. Fed mosquitoes had longer longevity compared to unfed ones. Morphological identification showed that Aedes aegypti aegypti-like mosquitoes were more predominant than Aedes aegypti formosus-like mosquitoes in all the study sites, suggesting the predominance of Aedes aegypti in the urban environment. Our data suggest that the geographical origin of Aedes aegypti mosquitoes in Burkina Faso has a little effect on its life history traits.

The interference-fit size has a significant effect on CFRP/Al-alloy laminates riveted lap joints, the requirements for the interference-fit size are different because of the strengthening of heterogeneous materials. However, in the process of the riveted CFRP/Al-alloy, the heterogeneous laminates lead to poor structural strength because of the different requirements of interference-fit size. Therefore, the different assembly types of riveting mold are designed to acquire a novel interference-fit size, and the tensile test is adopted to evaluate the tensile property. In addition, the fracture failure of CFRP/Al-alloy laminates riveted lap joint is observed by the ultra-depth of field microscope. Finally, the best assembly type is the trapezoid riveting mold combined with an arc riveting die, and the sidewall intersection angle of the trapezoid riveting mold is 66° which could achieve a suitable interference-fit size and a better mechanical performance.

Coffee is regarded as the highly consumed beverage throughout the world and has established a key spot in the world economy as an important commodity for trading. In general, they are produced by brewing their roasted and ground beans, which release aromatic coffee; as well as produce an equivalent amount of spent coffee grounds (SCG). Previously, they were discarded as wastes or used as natural pest repellent or garden fertilizer; however, in recent times, are valorized into biofuels owing to their high calorific value. In fact, SCG briquettes have gained wide attention for supplying energy renewably, especially to the rising energy demand; and also have been identified as an effective measure to reduce their pollution. With this in mind, this present chapter focuses on reviewing the availability and chemistry involved in these SCG wastes, pre-treatments and preparations required for their briquetting, compacting techniques followed, and fuel characteristics of their briquettes, from various available works of literature. Here, their availability showcases the amount of SCG wastes generated with respect to time and consumption, wherein understanding their chemistry helps in deciding the pre-treatments necessary for their briquetting. Meanwhile, preparation techniques briefs about the necessary pre-treatments undertaken before compaction by different researchers; and the fuel characteristics define the physicochemical and mechanical properties of their briquettes, developed using various compaction methods. Besides, combustion behaviors of these briquettes are explained in terms of their burning characteristics and emission levels, as reported in literatures; which help in deciding their suitability as a replacement for existing fossil coal. Eventually, all the reported data were in accordance with their permissible standards and suggested these SCG as a highly renewable solid biofuel.

The bimodal grain-size distribution 0.9KNbO₃-0.1BaTiO₃ ceramics, with a typical perovskite structure in tetragonal phase at room temperature, were successfully prepared by an induced abnormal grain growth (IAGG) method at a relatively low sintering temperature. In this bimodal grain-sized distribution structure, the extra-large grains (about 10‒50 μm) were evolved from the micron-sized filler powders and the fine grains (about 0.05‒0.35 μm) were derived from the sol precursor matrix. The 0.9KNbO₃-0.1BaTiO₃ ceramics exhibit relaxor-like behavior with the diffused phase transition near room temperature, and confirmed by the existence of the polar nanodomain regions (PNRs) using the HRTEM images. The large room-temperature electrocaloric (EC) effect was found, characterized by an adiabatic temperature drop of 1.5 K, an isothermal entropy change of 2.48 J kg^-1 K^-1, and high EC strengths of ïDT/DEï = 1.50×10^-6 KmV^-1 and DS/DE = 2.48×10^-6 Jmkg^-1K^-1V^-1directly measured under E = 1.0 MV/m. These excellent ECEs demonstrate that this simple IAGG method is highly appreciated for synthesizing high-performance EC materials for efficient cooling devices.

Ayurveda as a healthcare system has survived for thousands of years but continues to be dogged by reported lack of efficacy of the treatments in clinical trials. The reported lack of efficacy could be due to a real lack of efficacy (which then contradicts the survival of Ayurveda as a functional medical system enjoying considerable public patronage) or could be attributed to inadequacies in the efforts towards evidence generation or in a larger context the overall scientific conduct of research in Ayurveda. In an effort towards better evidence generation, there is an immediate need for standardizing the design, conduct and reporting of clinical trials of Ayurveda but it is a daunting task. For this effort to benefit the scientific endeavors of Ayurveda researchers, it should allow the researchers to be able to apply Ayurveda’s multi-component, individualized and inherently holistic approach. Statistical principles can benefit this effort. Statistical hypothesis testing (SHT) is central to these statistical principles and also aligns well with conventional scientific principles of evidence generation. Although there are challenges with SHT, good practitioners engaged in it do much more than just apply the mathematical theory behind it. As a particular example, lot of time in clinical trial designing is spent in addressing biases and designing trials prudently by minimizing the effect of such biases. SHT can benefit such an effort objectively. There is a need for Ayurveda researchers to engage deeply and mindfully about biases in study design in order to gain scientific validity and acceptability. The article highlights issues that arise in Ayurveda research, and discusses few ways of dealing with these issues using statistical principles.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

Artificial Intelligence is dominated by Artificial Neural Networks (ANNs). Currently, the Batch Gradient Descent (BGD) is the only solution to train ANN weights when dealing with large datasets. In this article, a modification to the BGD is proposed which significantly reduces the training time and improves the convergence. The modification, called Instance Eliminating Back Propagation (IEBP), eliminates correctly-predicted-instances from the Back Propagation. The speedup is due to the elimination of unnecessary matrix multiplication operations from the Back Propagation. The proposed modification does not add any training hyperparameter to the existing ones and reduces the memory consumption during the training.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

A novel gas-phase electrocatalytic system based on a low-temperature proton exchange membrane (Sterion) was developed for the gas phase electrocatalytic conversion of CO2 to liquid fuels. This system achieved gas-phase electrocatalytic reduction of CO2 at low temperatures (below 90 ºC) over a Cu cathode by using water electrolysis-derived protons generated in-situ on an IrO2 anode. Three Cu-based cathodes with varying metal particle sizes were prepared by supporting this metal on an activated carbon at three loadings (50, 20, and 10 wt%; 50%Cu-AC, 20%Cu-AC, and 10%Cu-AC, respectively). The cathodes were characterized by N2 adsorption–desorption, temperature-programmed reduction (TPR), and X-ray diffraction (XRD) whereas their performance towards the electrocatalytic conversion of CO2 was subsequently studied. The membrane electrode assembly (MEA) containing the cathode with the largest Cu particle size (50%Cu-AC, 40 nm) showed the highest CO2 electrocatalytic activity per mole of Cu, with methyl formate being the main product. This higher electrocatalytic activity was attributed to the lower Cu–CO bonding strength over large Cu particles. Different product distributions were obtained over 20%Cu-AC and 10%Cu-AC, with acetaldehyde and methanol being the main reaction products, respectively. The CO2 consumption rate increased with the applied current and the reaction temperature.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

The study’s objective is to analyse the mechanical properties of steel pipe piles as a part of a trestle bridge subjected to five years of natural marine corrosion degradation. Sixteen tensile specimens were extracted from the steel pipe piles in the splash, tidal, and immersion zones. The experimental tensile test results are used to establish regression equations defining elastic modulus, yield strength, strain hardening index, and strength coefficient for the true stress-strain curves of the three regions. A non-linear time-dependent mathematical model is exploited to identify the corrosion degradation using the data from one single corrosion degradation measurement campaign. The analysis indicated that the splash zone experiences the most severe corrosion degradation, and there are progressive losses in the mechanical properties of each zone as the corrosion degradation progresses. The established relationships of the mechanical properties, as a function of the ratio of corroded plate thickness to the as-built one, can be used as a fast-engineering approach to identify the mechanical properties of severely corroded piles. The corrosion degradation allowance is also defined using the First Order Reliability Method, accounting for existing uncertainties covered by the partial safety factors. By examining the impact of marine corrosion on the mechanical properties of marine structures and developing predictive models to assess the corrosion’s effect on material strength and corrosion allowance, the study aims to improve offshore structures’ safety, design, and maintenance.

Durability of concrete requires a dense microstructure which can be achieved by using self-compacting concrete (SCC). Both calcined clay (CC) and rice husk ash (RHA) are promising supplementary cementitious materials (SCMs) that can partially replace cement, but their use in SCC is critical due to their higher water demand and specific surface area (SSA) compared to cement. Empirical method of SCC design was adopted considering the physical properties of both CC and RHA. The influence of partially substituting cement at 20 vol-% with binary and ternary blends of CC and RHA were investigated. The fresh properties of SCC were investigated using a variety of tests. The time dependent workability was monitored by plunger method and flow resistance determined based on the rheological measurements of SCC. The evolution of the hydrate phases of the binder in SCC was determined by thermogravimetric analysis, while the durability was evaluated by rapid chloride migration test. Cement partial replacement with 20 vol-% CC has no significant effect on SCC fresh, time dependent, compressive strength and durability properties. 20 vol-% RHA on the other hand requires higher dosage of SP to achieve self-compactability and increased the viscosity of SCC. Its workability retention is only up to 30 min after mixing and exhibited higher flow resistance. It consumes more CH and improves compressive strength and chloride resistance of SCC. The ternary blending with CC and RHA yielded better fresh SCC properties compared to the binary blend with RHA, while an improved chloride penetration resistance could be achieved compared to binary CC blend.

RNA interference is a highly conserved process in which non-coding small RNAs (sRNA) modulate gene expression at the post-transcriptional level influencing plant growth and development. Dicer-like (DCL), Argonaute (AGO) and RNA-dependent RNA polymerase (RDR) are the core elements involved in gene silencing and their gene families have been explored in many plants. However, these genes and their response to abiotic stresses have not yet been well in wheat. In this study, 82 AGO, 31 DCL, and 31 RDR genes were identified and phylogenetic analysis of these proteins showed that clustered into ten, four and four clades respectively. RNA-seq analysis revealed constitutive expression of AGO1, AGO9, and DCL2 family expression analysis in tissues under normal and stress conditions, whereas RDR1 which is known to engage in siRNA biogenesis showed higher expression levels in wheat leaf tissues. Our findings build the foundation for comparative genomics analyses of RNA silencing elements in cereal crops, as well as new insights into the functional complexity of RNA silencing in wheat stress responses, which is critical for understanding the processes underlying wheat stress responses.

The mathematical modelling of reverse logistics inventory systems ignores that returned items may arrive out of sequence, i.e. with different number of remanufacturing times. Moreover, such modelling assumes that the retuned items may retain the same quality upon recovery regardless of how many times they have been previously remanufactured. This paper develops a new mathematical expression of the percentage of retuned items that can be remanufactured a finite number of times. The proposed expression is modelled as a function of the expected number of times an item can be remanufactured on its life cycle and the number of times an item can be technologically (or optimally) remanufactured based on its quality upon recovery. The model developed in this paper considers joint production and remanufacturing options. The return rate is a varying demand dependent rate, which is a decision variable with demand, product deterioration, manufacturing and remanufacturing rates being arbitrary functions of time. The model considers the initial inventory of returned items in the mathematical formulation, which enables decision makers to adjust all functions and input parameters for subsequent cycles. Illustrative examples indicate that dependent purchasing price of recovery items and the incorporation of remanufacturing investment cost significantly impact on the optimal remanufacturing policy.

The COVID-19 pandemic affects all parameters, especially health care professionals, drugs and medical supplies. The KERRA is a mixed medicinal plant capsule that is used for the treatment of patients with high fever with food and drug administration approved by FDA Thailand. Recently, KERRA showed quicker recovery for COVID-19 patients. Therefore, it is possible that some ingredients in KERRA could inhibit SARS-CoV-2. In this study, two important replication-related enzymes in SARS-CoV-2, a main protease and an RNA-dependent RNA polymerase (RdRp), were used to study the effect of KERRA. The results showed that KERRA inhibited the SARS-CoV-2 main protease and SARS-CoV-2 RdRp with IC50 values of 49.91 ± 1.75 ng/mL and 36.23 ± 5.23 µg/mL, respectively. KERRA displayed no cytotoxic activity on macrophage cells at concentrations lower than 1 mg/mL and exhibited anti-inflammatory activity. Additionally, KERRA was against a feline coronavirus (feline infectious peritonitis [FIP]) infection with an EC50 value of 134.3 g/mL. This study supports the potential use of KERRA as a candidate drug for COVID-19.

This paper presents sufficient conditions for almost global stability of nonlinear switched systems consisting of both stable and unstable subsystems. Techniques from the stability analysis of switched systems have been combined with the multiple Lyapunov density approach - recently proposed by the authors for the almost global stability of nonlinear switched systems composed of stable subsystems. By using slow switching for stable subsystems and fast switching for unstable subsystems lower and upper bounds for mode-dependent average dwell times are obtained. In addition to that, by allowing each subsystem to perform slow switching and using some restrictions on total operation time of unstable subsystems and stable subsystems, we have obtained a lower bound for an average dwell time.

Here, I introduce a concept called autonomous selection to refer to a source of selection that is part of the individuals upon which it acts. The concept is motivated by a set of phenomena with the following characteristics: Natural selection shaped a variant (e.g., gene, epigenetic mark, or combination thereof) to act in a manner that reduces the frequency of one or more heritable traits of the individual in which it is located if those traits are detrimental to individual or group fitness. Phenomena with these characteristics are peculiar to traditional evolutionary theory but have been identified rather frequently in recent decades. They are also relevant to adaptive evolution: By reducing the frequency of a trait detrimental to fitness, the variant accelerates the evolution of adaptations, which allows its holders to adapt better to constantly changing environments. The variant is shaped by (natural) selection, but also does (autonomous) selection. Several phenomena with these characteristics have been invoked by proponents of the extended evolutionary synthesis (EES). The concept of autonomous selection helps resolve some of the controversy surrounding the EES: EES proponents call attention to the incompleteness of contemporary theory, emphasizing individuals’ processes that influence which adaptations those individuals evolve. I argue for the special importance of individuals’ processes that do not just influence those individuals’ adaptations, but also accelerate the adaptive evolution of those individuals. All known phenomena that fit this description are examples of autonomous selection. Other phenomena raised by EES proponents do not meet this threshold.

Based on the Expected Utility Theory and Regret Theory, the Extended Regret Theory (ERT) is proposed in this paper to study the optimal pricing strategy of retailers in e-commerce environment. Taking the diversity of sales channels and the uncertainty of consumers in e-commerce environment into consideration, author of the paper designs an extended regret utility function which comprehensively considers both pessimistic and optimistic attitudes of decision makers in retailing industry to describe their regret-avoidance behavior. According to the sensitivity analysis, it is found that the optimal retail price decreases as the consumer price sensitivity coefficient increases, yet does not show variation with changes of the consumers pessimism degree. Moreover, the optimal retail price(s) obtained under EUT, ERT and combination of EUT and ERT represent the same.

Akt1 is a proto-oncogene that is over active in most cancers. Akt1 activation requires phosphorylation at Thr308; phosphorylation at Ser473 further enhances catalytic activity. Akt1 activity is also regulated via interactions between the kinase domain and the N-terminal auto-inhibitory pleckstrin homology (PH) domain. As it was previously difficult to produce Akt1 in site-specifically phosphorylated forms, the contribution of each activating phosphorylation site to auto-inhibition was unknown. Using a combination of genetic code expansion and in vivo enzymatic phosphorylation, we produced Akt1 variants containing programmed phosphorylation to probe the interplay between Akt1 phosphorylation status and the auto-inhibitory function of the PH domain. Deletion of the PH domain increased the enzyme activity for all three phosphorylated Akt1 variants. For the doubly phosphorylated enzyme, deletion of the PH domain relieved auto-inhibition by 295-fold. We next found that phosphorylation at Ser473 provided resistance to chemical inhibition by Akti-1/2 inhibitor VIII. The Akti-1/2 inhibitor was most effective against pAkt1T308 and showed 4-fold decreased potency with Akt1 variants phosphorylated at Ser473. The data highlight the need to design more potent Akt1 inhibitors that are effective against the doubly phosphorylated and most pathogenic form of Akt1.

The characteristics of tight sandstone, such as small pores, complex pore structures, low permeability, and low porosity, make it difficult to accurately characterize its pore structure. This represents a major challenge in the exploration and development of tight sandstone oil and gas reservoirs. This article conducts a simulation study on the impact of characteristic parameters such as pore size, coordination number, pore-throat ratio, and wettability on microscopic remaining oil after polymer flooding, thereby quantifying the types of remaining oil.

This paper investigates the influence of sample size and layer height on the elastic modulus of samples 3D printed by fused filament fabrication (FFF). Cubic samples of different sizes from either a stiff thermoplastic polymer (polycarbonate (PC)) or a soft polymer (thermoplastic polyurethane (TPU)) were printed at three different layer heights: 0.1 mm, 0.2 mm, and 0.4 mm. The samples were imaged using micro-computed tomography to visualize porosity and tested under compression. The results indicate that the elastic modulus of TPU varied with sample size, demonstrating size effects due to high porosity. In contrast, PC samples had a low void volume fraction and did not demonstrate statistically significant size effects on the elastic modulus. The variations in elastic modulus due to layer height were statistically significant for both materials. The highest elastic modulus was observed at 0.2 mm layer height for both materials across different sample sizes, which can be attributed to low void volume fractions. The study develops process-structure-property relations for PC and TPU samples manufactured by FFF. It provides new insights into the design guidelines for FFF based on the size effects. The results indicate that variations in mechanical properties due to size effects must be considered during the design stage for TPU to accurately predict the material’s behavior. Additionally, the locations of the printed parts that are subjected to higher loads should be printed closer to the heated print bed due to the lower void volume fraction observed in the section of the samples printed adjacent to the heated print bed.

This study explores the multifaceted influence of litter size, maternal care, exercise, and aging on rats' neurobehavioral plasticity and dentate gyrus microglia dynamics. Body weight evolution revealed a progressive increase until maturity, followed by a decline during aging, with larger litters exhibiting lower weights initially. Notably, exercised rats from smaller litters displayed higher body weights during mature and aged stages. Dentate gyrus volumes showed no significant differences among groups, except for aged sedentary rats from smaller litters, which exhibited a reduction. Maternal care varied significantly based on litter size, with large litter dams showing lower frequencies of caregiving behaviors. Behavioral assays highlighted the detrimental impact of a sedentary lifestyle and reduced maternal care/large litters on spatial memory, mitigated by exercise in aged rats from smaller litters. Microglial dynamics in the layers of dentate gyrus revealed age-related changes modulated by litter size and exercise. Exercise interventions mitigated microgliosis associated with aging, particularly in aged rats. These findings underscore the complex interplay between early-life experiences, exercise, microglial dynamics, and neurobehavioral outcomes during aging.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

Parkinson’s disease (PD) is the second-most common neurodegenerative disorder worldwide and is diagnosed based upon motor impairments. Non-motor symptoms are well-recognized in PD, and peripheral neuropathy is a frequent but poorly appreciated non-motor sign. Study of how the central and peripheral sensory systems are affected can contribute to the development of targeted therapies and deepen the understanding of the pathophysiology of PD. Although the cause of sporadic PD is unknown, chronic exposure to the pesticide rotenone in humans increases the risk of development of PD. Here, we aimed to investigate whether peripheral neuropathy is present in a traditional model of PD. Mice receiving intrastriatal rotenone showed greatly reduced dopamine terminals in the striatum and reduction in tyrosine hydroxylase-positive neurons in the Substantia nigra pars compacta and developed progressive motor impairments in hindlimb stepping and rotarod but no change in spontaneous activity. Interestingly, repeated testing using gold-standard protocols showed no change in gut motility, a well-known non-motor symptom of PD. Importantly, we did not observe any change in heat, cold, or touch sensitivity, again based upon repeated testing with well-validated protocols that were statistically well-powered. Therefore, this traditional model fails to replicate PD, and our data again reiterate the importance of the periphery to the disorder that is PD.

The study delves into the critical examination of the Size of Loss distribution patterns in the context of auto insurance during pre- and post-pandemics, emphasizing their profound influence on insurance pricing and regulatory frameworks. Through a comprehensive analysis of the historical Size of Loss data, insurers and regulators gain essential insights into the probabilities and magnitudes of insurance claims, informing the determination of precise insurance premiums and the management of case reserving. This approach aids in fostering fair competition, ensuring equitable premium rates, and preventing discriminatory pricing practices, thereby promoting a balanced insurance landscape. The research further investigates the transformative impact of the COVID-19 pandemic on these Size of Loss patterns, given the substantial shifts in driving behaviors and risk landscapes. Also, the research contributes to the literature by addressing the need for more studies focusing on the implications of the COVID-19 pandemic on pre- and post-pandemic auto insurance loss patterns, thus offering a holistic perspective encompassing both insurance pricing and regulatory dimensions.

Complex-structured polymeric microparticles hold significant promise as advance in next-generation medicine mostly due to demand from developing targeted drug delivery. However, the conventional methods for producing these microparticles of defined size, shape and sophisticated composition often face challenges in scalability, reliance on specialized components such as micro-patterned templates, or have limited control over particle size distribution and cargo release kinetics. In this study, we introduce a novel and reliably scalable approach for manufacturing microparticles of defined structures and sizes with variable parameters. The concept behind this method involves the deposition of a specific number of polymer layers on a substrate with low surface energy. Each layer can serve as either the carrier for cargo or a programmable shell-former with predefined permeability. Subsequently, this layered structure is precisely cut into desired-sized blanks using a laser. The manufacturing process is completed by applying of heat to the substrate what results on sealing the edges of the blanks. The combination of the high surface tension of the molten polymer and the low surface energy of the substrate enables the formation of discrete particles, each possessing semi-spherical or other designed geometries determined by their internal composition. Such anisotropic microparticles are envisaged versatile applications.

The production of anatase titanium dioxide particles plays a crucial role in the sulfate process used for manufacturing white pigment. A key factor in improving the quality of white pigments is enhancing the thermal mixing process within the precipitation tank. This improvement ensures the uniform dispersion of seed particles instead of their agglomeration, leading to the formation of particles with uniform sizes. The objective of this study was to enhance three-phase CFD simulations involving the mixing process of H₂SO₄ solution, steam as a gas phase, and solid seed particles. By analyzing the trajectories of the seed particles using CFD, the optimal injection position for the seed particles within the mixing process was determined. Subsequently, lab scale test and real field test were conducted based on the insights gained from the CFD simulations. The particle size distribution of two different types of seed inlets was analyzed and compared using Transmission Electron Microscopy (TEM). The findings of this study demonstrate that the developed multi-phase CFD simulation can be effectively utilized to enhance the precipitation process for the production of anatase titanium dioxide particles.