The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

In this study, we investigate the influence of control type and strain rate on the lifetime of specimens manufactured from 50CrMo4. This influence is described by a strain rate dependent method that uses cyclic stress strain curves to correct displacement controlled cyclic test results. The objective of this correction is to eliminate the stress related differences between displacement controlled cyclic test results and force controlled cyclic test results. The method is applied to the results of ultrasonic fatigue tests of six different combinations of heat treatment, specimen geometry (notch factor) and atmosphere. The corrected results show an improved agreement with test results obtained on conventional fatigue testing equipment with similar specimens: the standard deviation in combined data sets is significantly reduced (p=4.1%). We discuss the literature on intrinsic and extrinsic strain rate effects in carbon steels.

Abiotic stress in plants is an increasingly common problem in agriculture, and thus, studies on plant treatments with specific certain compounds that may help to mitigate these effects have increased in recent years Melatonin (MET) application and its role in mitigating the negative effects of abiotic stress in plants have become important in the last few years. MET, a derivative of tryptophan, is an important plant-related response molecule involved in the growth, development, and reproduction of plants, and the induction of different stress factors. In addition, MET plays a protective role against different abiotic stresses such as salinity, high/low temperature, high light, waterlogging, nutrient deficiency and stress combination by regulating both the enzymatic and non-enzymatic antioxidant defense systems. Also, MET interacts with many signaling molecules, among these, reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. It is well known that NO produces S-nitrosylation and NO2-Tyr of important antioxidant-related proteins, being this an important mechanism for maintaining the antioxidant capacity of the AsA/GSH cycle under nitro-oxidative conditions, being extensively reviewed here under different abiotic stress conditions. Lastly, in this review, we show the coordination between NO and MET as a long-range signaling molecule, regulating many responses in plants, including plant growth and abiotic stress tolerance. Despite all the knowledge acquired over the years, there is still more to know about how MET and NO act on tolerance to abiotic stresses.

Background: Cervical cancer prevention in regions with limited access to screening and HPV vaccination necessitates innovative approaches. This study explored the potential of a test-and-treat strategy using mRNA HPV tests to impact cervical cancer prevention in a high-prevalence HIV population. Methods: A cervical screening study was conducted at three South African hospitals involving 710 under-screened, non-pregnant women (25 to 65 years) without known cervical diseases. Cytology, HPV testing, colposcopy, and biopsies were performed concurrently. Histopathologists determined final histological diagnoses based on biopsy and LLETZ histology. mRNA-HPV-genotyping for 3 (16, 18, 45) to 8 (16, 18, 31, 33, 35, 45, 52, 58) high-risk types was performed on leftover liquid-based cytology material. The preventive potential of the test-and-treat approach was estimated based on published data, reporting the causative HPV types in cervical cancer tissue from South African women. Treatment was provided as needed. Results: HPV positivity rate more than doubled from 3-type (15.2%; 95% CI: 12.6-17.8) to 8-type mRNA (31.5%; 95% CI: 28.8-34.9) combinations, significantly higher among HIV-positive women. CIN3+ prevalence among HIV-positive women (26.4%) was double that of HIV-negative women (12.9%) (p&lt;0.01). The 6-type combination showed the best balance of sensitivity, specificity and treatment group size, and effectiveness to prevent cervical cancer. A 4-type combination (16, 18, 35, 45) could potentially prevent 77.6% (95% CI: 71.2-84.0) of cervical cancer burden by treating 20% and detecting 41.1% of CIN3 cases in the study group. Similarly, a 6-type combination (16, 18, 31, 33, 35, 45), treating 25% and including 62% of CIN3 cases, might prevent 85% of cervical cancer cases (95% CI: 79.6-90.6) among HIV-positive and negative women. Conclusion: Employing mRNA HPV tests within a test-and-treat approach holds huge promise for targeted cervical cancer prevention in under-screened populations. Testing for mRNA of the 6 highest-risk HPV types in this population and treating them all is projected to effectively prevent progression from CIN3 to invasive cervical cancer while reducing overtreatment in resource-constrained settings.

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

Abstract: Power generation using dielectric elastomer (DE) artificial muscle is attracting attention because of its light weight, low cost, and high efficiency. Since this method is a system that produces electricity without emitting carbon dioxide nor using rare earths, it would contribute to the goal of environmental sustainability. In this paper, the background of DEs, the associated high-efficient wave energy generation (WEG) systems that we developed using DEs, as well as the latest development of its material are summarized. By covering the challenges we face and the achievements that we’ve reached, we can discuss the opportunities to build the foundation of a recycled energy society through the usage of these WEGs. On the other hand, to make these possibilities commercially successful, the advantages of DEs need to be integrated with traditional technologies. To achieve this, we also consider the method of using DEs alone and a system used in combination with an oscillating water column. Finally, the current status and future of DEGs are discussed.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

This study investigates the integration of natural intelligence (NI) and artificial intelligence (AI) within traditional firms, proposing a multilayer network framework to enhance economic value. The research explores the central question: How can the integration of NI and AI, facilitated by copula nodes, drive economic value creation in digitized firms? Through empirical testing across multiple industries—namely manufacturing, retail, and finance—the study evaluates the cost-benefit improvements associated with AI adoption. The findings reveal substantial efficiency gains, improved decision-making, and notable cost reductions, validating the proposed model's predictions. The study emphasizes the critical role of copula nodes in optimizing interactions between NI and AI, ensuring that their integration yields maximum economic benefits. By providing a novel framework for quantifying AI's economic impact within digitized firms, this research fills a significant gap in the literature on multilayer networks and intelligent systems. The practical implications are profound, offering a strategic pathway for firms to enhance profitability and competitiveness in the digital age.

An ambitious per capita GDP target has been envisioned by the Chinese government since 2020 to project its sustainable economic growth rate by 2035. Can China fully achieve its goal? This is a question worth investigating. By inserting relevant TABLO modules of the final goods trade, the intermediate goods trade, and factor-strengthening technology spillovers, along with technology absorption thresholds effects of the global value chain, this study builds a global dynamic recursive computational general equilibrium (CGE ) model on basis of GTAP-RD. This approach allows considering the 'dual circulation' system strongly advocated and pointed out as the sole way to realize China’s technological (total factor productivity (TFP)) progress by the Chinese government, which integrates both domestic internal and international external circulations (trade and foreign direct investment (FDI)). We simulate China's technological progress under eight scenarios, and use the latest GTAP Version 11 production and trade data (released in April 2023) for 141 countries and regions and results are aggregated into 10 countries groups with 9 activity sectors and 10 commodities. Main conclusions are as follows: (1) If China maintains its trade opening policy, the 2035 vision goal can be achieved, with external circulation being more important than internal circulation for technological spillovers. (2) The economic growth impacts of external and internal circulation operate relatively independently. However, FDI provides a relatively larger synergistic effect for all forms of external trade circulation than to the internal one. Regarding factor-strengthening effects, spillovers are more favorable to 'capital' than to labor factors. (3) We find that the Regional Comprehensive Economic Partnership Agreement is the most important strategic partner for China. (4) It appears that FDI is not an effective way to lift the productive services sector's total factor productivity (TFP), and more realistic for China is to open up the productive services market more widely, as its efficiency is a pivotal reflection of China's independent innovation capability. (5) China–US decoupling has an enormous global impact. In all the Scenarios we consider, the United States is always the country that loses the most, and Europe would be the group of countries that benefits when there is a large increase in TFP in the US.

Evaluation ecosystem service value (ESV) is critical for “lucid waters and lush mountains are invaluable assets”. However, the ESV estimation and spatial-temporal analysis for mountainous soil erosion area is rare, e.g., Changting county, China. In this study, we developed a remote sensing driven mountainous equivalent factor (RS-MEF) method to estimate the ESV of soil erosion area in subtropical mountain. It is a hybrid of a conventional equivalent factor framework and the remote sensing techniques for mountains, and achieves several highlights of spatial adjustment using carbon sink with vegetation canopy, improvement spatial resolution, and removal topographic effect. Using the RS-MEF method, we estimated that the ESV of Changting county was about 15.80 billion CNY in 2010 and 34.83 billion CNY in 2022. Specifically, the ESV per unit area of major soil erosion area (MSEA) in the county was less than that of non-major soil erosion area (n-MSEA), however, the ESV growth rate of MSEA from 2010 to 2022 was faster than that of n-MSEA. Therefore, the ESV gap between two areas was shortened from 28.99% in 2010 to 15.83% in 2022. Topographic gradient effect analysis illustrates that the area with high elevation and small slope is one control focus in the next step. Our study indicates that the ecological restoration in the county has made great achievements in the ESV perspective, with low ESV area shrank evidently in MSEA; and the achieved knowledge of the ESV growth and inherent factors is valuable and instructive for the next soil and water conservation.

This research aims to enhance scholarly understanding Analysis of potential Value Creation research on managing transit oriented that may arise from Mass Rapid Transit resources through an extensive literature review, analyzing 235 papers from the Scopus database spanning 2011-2024, with a specific focus on value creation managing transit-oriented area. Data collection was conducted on January 1, 2024, using Harzing's Publish or Perish tool. The selected studies are associated with keywords such as 'managing transit orientation (154 papers), Value creation MRT (45 papers), Innovation MRT (36 papers)/ In the filtering process, 235 papers were assessed, excluding those unrelated to the research focus on the cash flow statement. The inclusion of 31 carefully selected articles reflects a targeted approach, ensuring alignment with the research focus on value creation in managing transit orientation a relevant dataset for analysis. This article was created by accessing several scientific articles regarding the application of identification in managing transit orientation using Vos viewer. Value creation research in managing transit oriented is needed to explore the following areas: Long-term sustainability of identified core competencies, Competitive Imitation, Organizational Adaptability, Industry Specific Applications, Performance Measurement, Dynamic Capability Development, Cross-Cultural Perspective. Potential areas for further research include Incorporate additional contingent factors into the model, such as environmental dynamism and competitiveness, to test the validity of the Resource-Based View (RBV) model. Extend the analysis to small and medium-sized businesses to examine how organizational structure and competitive strategy impact performance in this context.

Predicting type 2 diabetes mellitus (T2DM) using phenotypic data with machine learning (ML) techniques has received significant attention in recent years. PyCaret, an ML tool that enables the simultaneous application of 16 different algorithms, was used to predict T2DM using phenotypic variables from the “Nurses’ Health Study” and “Health Professionals’ Follow-up Study” datasets. Ridge classifier, Linear Discriminant Analysis, and Logistic Regression (LR) were the best-performing models for the male-only data subset. For the female-only data subset, LR, Gra-dient Boosting Classifier, and CatBoost Classifier were the strongest models. The AUC, accuracy, and precision were 0.77, 0.70, and 0.70 for males and 0.79, 0.70, and 0.71 for females, respective-ly. The feature importance plot showed that familial history of diabetes (famdb), never having smoked, and high blood pressure (hbp) were the most influential features in females, while famdb, hbp, and current smoking were the major variables in males. In conclusion, PyCaret was used successfully for speed analysis for the prediction of T2DM by simplifying complex ML tasks. Gen-der differences are an important consideration for T2DM prediction. Despite this comprehensive ML tool, phenotypic variables alone may not be sufficient for early T2DM prediction; genotypic variables could also be used in combination for future studies.

Long-range HNCO NMR spectra for proteins show crosspeaks due to 1JNC, 2JNC, 3JNCg and h3JNC couplings. The h3JNC couplings are transmitted through hydrogen bonds and are correlated to hydrogen bond lengths. We collected long-range HNCO data at a series of temperatures for four protein states. P22i and CUS-3i are six-stranded beta-barrel I-domains from phages P22 and CUS-3 that share less than 40% sequence identity. The cis and trans states of the C-terminal domain from pore-forming toxin hemolysin ΙΙ (HlyIIC) arise from isomerization of a single G404-P405 peptide bond. For P22i and CUS-3i the hydrogen bonds detected by NMR agree with those observed in the corresponding domains from cryoEM structures of the two phages. Hydrogen bond lengths derived from the h3JNC couplings, however, are poorly conserved between the distantly related CUS-3i and P22i domains and show differences even between the cis and trans states of HlyIIC. This is consistent with hydrogen bond lengths being determined by local differences in structure rather than the overall folding topology. With increasing temperature hydrogen bonds typically show an apparent increase in length, which has been attributed to protein thermal expansion. Some hydrogen bonds are invariant with temperature, however, while others show apparent decreases in length suggesting they become stabilized with increasing temperature. Considering the data for the three proteins in this study and previously published data for ubiquitin and GB3, lowered protein folding stability and cooperativity correlates with a larger range of temperature responses for hydrogen bonds. This suggests a partial uncoupling of hydrogen bond energetics from global unfolding cooperativity as protein stability decreases.

This paper aims to provide an evaluation of how Value Added Tax (VAT) policy alterations influence market liquidity, trading volume, and stock performance. To fill the existing literature gap on the direct effect of (VAT) adjustments on stock market dynamic, particulate within the banking industry. The study employs an event study methodology to analyse the immediate and medium-term effects on bank stocks listed in markets subject to a (VAT) adjustments. The core of the study analysis is anchored around two pivotal events, the initial application of (VAT) on 1st January 2018, and the subsequent (VAT) increase to 15% on 1st July 2020 using MATLAB R2022b. The study analysis encompasses the period immediately before and after the introduction and subsequent increase (VAT) in kingdom Saudi Ariba (KSA) employing an eleven sample comprises the (KSA) largest banks with a ±7 days window period from the event. The analysis revels that the imposition of 5% (VAT) lead a substation downturn in trading volume and stock returns of 9.5%, and 39.5%, subsequently. While when the (VAT) was increased by 15% the market exhibited a mixed but ultimately positive response of 3.3% trading volumes increases and 128.7% average stock return recovery.

This study examines the influences of live streaming servicescape on Chinese consumers' luxury purchase intention. Interestingly, for the sample without luxury purchase experience, the mediating effect of the perceived value of luxury goods is significant but effect of consumer trust is not. For the sample with luxury purchase experience, the result of mediating effect is just the opposite. The interaction between conspicuous consumption and live streaming servicescape plays a certain role in regulating the perceived value of luxury goods. These results show that luxury brands can adopt innovation in the live streaming servicescape for different types of consumers to promote live streaming marketing. This study enriches the servicescape theory of live streaming.

Climate warming profoundly affect vegetative growth, flowering phenology and sexual reproduction of plants, therefore the ornamental value of wild flowers. Despite this, the extent and mechanism of the impact remain unclear. Here, we conducted warming experiment for two growing seasons (1.89 ℃ in 2017 and 2.37 ℃ in 2018 increases) with infrared heaters to examine the effects of warming on ornamental value of wild flower I. oxyanthera, endemic to China, in Mount Emei. We fitted generalized linear mixed models (GLMMs) and generalized linear model (GLM) to examine how warming affected plant morphology and floral traits. We evaluated comprehensive ornamental value based on plant morphology and flowering characteristics using Analytic Hierarchy Process (AHP) and disentangled the impact of the two traits on ornamental value using principal component analysis (PCA) and partial least squares structural equation model (PLS-SEM) under the ambient and warming treatments. Warming decreased significantly plant height and crown width, while increased branch number and single leaf area. Warming also decreased vexillum length, corolla tube length, nectar spur length and pedicel length. In addition, warming shortened flowering duration per plant and reduced flower number, while there was no significant effect on flower longevity, flower color at full-bloom stage between the control and warming treatment. Therefore, comprehensive ornamental value under warming was lower than that under the control. Pedicel length, flower color, flower longevity and flowering duration per plant were the main factors of affecting comprehensive ornamental value. PLS-SEM showed that warming had an indirect negative effect on ornamental value via direct negative effects on flowering traits. Collectively, these results indicate that although promoting vegetative growth, short-term warming decreased significantly ornamental value of I. oxyanthera due to warming-caused smaller flowers and shorter flowering duration.

This study empirically analyzes how R&D expenditures affect firm value using a regression model for listed firms in Shandong Province, China. The dependent variable is measured by To-bin Q, which measures firm value, and the experimental variable among the independent varia-bles is R&D expenditure. In addition, financial leverage and firm size, which have been found to have a significant impact on firm value in previous studies, were selected as control variables. The study sample consisted of 554 data points analyzed over a nine-year period from 2010 to 2018. Without controlling for variables that affect firm value, the correlation analysis shows that R&D expenditures of listed firms in Shandong Province, China have a significant positive impact on firm value at the 1% level. For a more precise analysis, we ran a multivariate regression analysis controlling for other variables that affect firm value and found that R&D expenditure has a significant positive impact on firm value at the 1% level. These findings suggest that man-agers of listed companies in Shandong Province, China, need to actively engage in R&D activi-ties to increase firm value. Companies in Shandong Province, China, are currently experiencing very strong growth, and this study, which shows that R&D is the key to increasing the value of these companies, can help companies in Shandong formulate their business strategies.

A rigorous perturbation analysis of the singular value decomposition of a real matrix of full column rank is presented. It is shown that the SVD perturbation problem is well posed only in case of distinct singular values. The analysis involves the solution of coupled systems of linear equations and produces asymptotic (local) componentwise perturbation bounds of the entries of the orthogonal matrices participating in the decomposition of the given matrix and of its singular values. Local bounds are derived for the sensitivity of the singular subspaces measured by the angles between the unperturbed and perturbed subspaces. An iterative scheme is described to find global bounds on the respective perturbations. The analysis implements the same methodology used previously to determine componentwise perturbation bounds of the Schur form and the QR decomposition of a matrix.

We examine a linear q-difference differential equation which is singular in complex time t at the origin. Its coefficients are polynomial in time and bounded holomorphic on horizontal strips in one complex space variable. The equation under study represents a q-analog of a singular partial differential equation, recently investigated by the author, which comprises Fuchsian operators and entails a forcing term that combines polynomial and logarithmic type functions in time. A sectorial holomorphic solution to the equation is constructed as a double complete Laplace transform in both time t and its complex logarithm log t and Fourier inverse integral in space. For a particular choice of the forcing term, this solution turns out to solve some specific nonlinear q-difference differential equation with polynomial coefficients in some positive rational power of t. Asymptotic expansions of the solution relatively to time t are investigated. A Gevrey type expansion is exhibited in a logarithmic scale. Furthermore, a formal asymptotic expansion in power scale is displayed, revealing a new fine structure involving remainders with both Gevrey and q-Gevrey type growth.

The recent years have been marked by rapid growth in the field of "ESG finance," leading to the emergence and expansion of ESG ratings and rating agencies. This study seeks to examine how financial investors respond to updates in ESG ratings provided by two prominent ESG rating agencies: MSCI and Refinitiv. Specifically, the goal is to determine whether any potential positive or negative alterations in a company's sustainability ratings directly affect its market value. The chosen methodology for this investigation is the Event Study, a model employed to assess the influence of economic events on corporate valuations by analyzing their Cumulated Average Abnormal Returns (CAARs). Over 840 instances of rating updates (events) were analyzed using a sample of 75 companies across various industries, all listed on major stock exchanges. The findings indicate that shifts in sustainability ratings, as evaluated by the two rating agencies, do not have a significant impact on companies' market capitalization. Moreover, these outcomes remain consistent over time, suggesting that financial markets are not assigning increasing significance to ESG ratings. Potential explanations are offered and discussed in relation to existing literature on the subject.

A The guinea pig value chain in Jauja, Peru, has been developed through the application of productive projects, institutional strengthening and implementation of the principles of responsible investment in agriculture and food systems (CFS-RAI). The actors in this chain have been showing economic improvements, representativeness and participation, characteristics that make them the key human capital for development. To improve the performance of the actors in the sustainable rural development of the territory of Jauja, Peru, the research carried out an evaluation of the competencies and capacities for project management in 46 actors linked to the business programme on the CFS-RAI Principles, representing 1,094 people in the guinea pig value chain in Jauja, using the Working With People (WWP) model and empirical instruments based on the Octagon method, International Project Management Association (IPMA) competencies, performance evaluation carried out by experts, attitudinal evaluation and the Business Model Canvas. The results have helped to structure the actors of the value chain, who show an intermediate mastery of project management competencies (2.73/5), institutional capacities in development (2.89/7) and a growing organizational management performance (26.2/100). In addition, trust and proactivity have been generated among the actors in the chain, with an interest in continuing with the implementation of the CFS-RAI Principles in order to achieve sustainability in their productive projects with commercial innovation. The results have allowed us to generate the design of an innovative programme for the development of competencies, which balances the three dimensions of IPMA competencies (perspective, person and practice) in connection with the CFS-RAI Principles. Both processes complement the strengthening of human capital in agrifood value chains through sustainable project management and contributing to sustainable development in the region.

The overexploitation of forest resources in the charcoal production basin of the city of Lubum-bashi (DR Congo) is reducing the resilience of miombo woodlands and threatening the survival of the riparian as well as urban human populations that depend on it. We assessed the socio-economic value and availability of plant-based non-timber forest products NTFPs in the rural area of Lubumbashi through ethnobotanical (100 respondents) and socio-economic (90 respondents) interviews, supplemented with floristic inventories, in two village areas selected on the basis of the level of forest degradation. The results show that 60 woody species, including 46 in the degraded forest (Maksem) and 53 in the intact forest (Mwawa), belonging to 22 families are used as sources of NTFPs in both villages. Among these species, 25 are considered priority species. NTFPs are collected for various purposes, including handcrafting, hut building, and traditional medicine. Moreover, the ethnobotanical lists reveal a similarity of almost 75%, indicating that both local communities surveyed use the same species for collecting plant-based NTFPs, despite differences in the level of degradation of the miombo woodlands in the two corresponding study areas. However, the plant-based NTFPs that are collected from miombo woodlands and traded in the urban markets have significant economic value, which ranges from 0.5 to 14.58 USD per kg depending on the species and uses. NTFPs used for handicraft purposes have a higher economic value than those used for other purposes. However, the sustainability of this activity is threatened due to unsustainable harvesting practices that include stem slashing, root digging, and bark peeling of woody species. Consequently, there is a low availability of plant-based NTFPs, particularly in the village area where forest degradation is more advanced. It is imperative that policies for monitoring and regulation of harvesting, and promoting sustainable management of communities’ plant-based NTFPs priority, be undertaken to maintain their resilience.

This paper contextualises the common queries of "why is crypto crashing?" and "why is crypto down?", the research transcends beyond the frequent market fluctuations to unravel how cryptocurrencies fundamentally work and the step-by-step process on how to create a cryptocurrency. The study examines blockchain technologies and their pivotal role in the evolving Metaverse, shedding light on topics such as how to invest in cryptocurrency, the mechanics behind crypto mining, and strategies to effectively buy and trade cryptocurrencies. Through an interdisciplinary approach, the research transitions from the fundamental principles of fintech investment strategies to the overarching implications of blockchain within the Metaverse. Alongside exploring machine learning potentials in financial sectors and risk assessment methodologies, the study critically assesses whether developed or developing nations are poised to reap greater benefits from these technologies. Moreover, it probes into both enduring and dubious crypto projects, drawing a distinct line between genuine blockchain applications and Ponzi-like schemes. The conclusion resolutely affirms the continuing dominance of blockchain technologies, underlined by a profound exploration of their intrinsic value and a reflective commentary by the author on the potential risks confronting individual investors.

The global prevalence of insulin resistance (IR) is increasing continuously, influencing metabolic parameters and fertility as well. The metabolic changes due to IR can alter the molecular composition of plasma and other body fluids. Follicular fluid (FF) is derived mainly from plasma, and it is a critical microenvironment for the developing oocytes. It contains various metabolites and amino acids, and the quality of the oocytes is linked at least partially to amino acid metabolism. Our goal was to determine quantitatively the amino acid (AA) profile of FF in IVF patients and to compare IR and non-insulin resistance (NIR) groups to investigate the AA changes in their FF. By UHPLC-based method we quantified the main 20 amino acids from human FF samples in the IR and NIR groups. Several amino acids (aspartate, glycine, glutamate, and cysteine) differed significantly (p&lt;0.05 or less) between the two groups. The most significant alterations between the IR and NIR groups were related to the glutathione metabolic pathway involving glycine, serine, and threonine. Since insulin resistance alters the amino acid composition of the FF, the oocytes may undergo metabolism-induced changes resulting in poor oocyte quality and less fertility in the insulin resistance groups.

With the continuous growth of electric and electronic appliances’ usage, the waste produced with obsolete material (e-waste) has an increasing environmental impact. Also, the production of such appliances bears to increased consumption of natural resources and produces a multitude of toxic and hazardous substances, which typically are not properly treated. One of the approaches that may be adopted to reduce such problems relies on the circularization of the current linear model, commonly adopted in the EEE value chain. This includes recovering eol products and reintroducing its parts, components, or raw materials into the value chain (e.g. semiconductors, circuit boards, raw metals, etc.), thus contributing to a more sustainable value chain. In this article, we present a state-of-art review that focuses on approaches and solutions for the EEE value chain traceability, and analyses the technologies that may be beneficial for promoting and implementing the CE model in this value chain.

Non-timber forest products (NTFP) have contributed in various ways to the living, livelihoods, and trading of households and communities who live in rural and urban areas all over the world. This paper analyses the value chain of Jiaogulan (Gynostemma pentaphyllum) in the Cao Bang Geopark, Vietnam. 106 actors were surveyed using a semi-structured questionnaire: experts (agricultural extension officers, farmers' associations), harvesters, traders, primary processors, processors, distributors, and consumers. The results show that a map of Jiaogulan value chain, value added of households in main market channels, and impact of value added and distribution of Jiaogulan products on household income.

The objective of this study was to evaluate the efficacy of fungal treatment (Pleurotus ostreatus) of urea-treated rice stubble on growth performance in slow-growing goats. Eighteen crossbred Thai native x Anglo-Nubian male goats (average body weight: 20.4 ± 2.0 kg) were randomly assigned to three experimental total mixed rations containing 35% rice stubble (RS) that was either untreated (URS), urea treated (UTRS) or treated with urea and fungi (UFTRS). URS and UTRS were cultivated and harvested from aseptically fungal spawn, incubated at 25-30 °C for 25 days. Indicators of growth performance were monitored and faeces were collected quantitatively to assess nutrient digestibility, during a 12-week feeding trial. All goats remained healthy throughout experiment. The goats fed UFTRS had a lower feed conversion ratio (kg feed/kg growth) compared to goats fed URS or UTRS. Compared to URS, dietary UFTRS increased nutrient digestibility of slow-growing goats, such as OM (+8.5%), CP (+5.5%), NDF (+39.2%), and ADF (+27.4%). Likewise, dietary UFTRS tended to increase rumen ammonia concentrations but rumen pH and volatile fatty acids were not affected by UFTRS. In conclusion, the present study indicates that the fungal treatment of RS is an effective tool to improve the growth performance of slow-growing goats.

An empirical model for log yield from trees is established and applied in microeconomics of carbon storage in a boreal spruce estate. The transition from pulpwood to sawlogs is a smoother function of stem diameter in the empirical data, in comparison to literature values. Correspondingly, the value transition of trees along with increasing size is gentler. Due to price premium of sawlogs from clearcuttings, all economically feasible treatment schedules terminate in clearcutting. Best capital return rates are gained with two heavy thinnings from above before clearcutting. Present carbon emission prices allow moderate carbon storage increment if the increment is compensated by proportional carbon rent. Doubling the present carbon prices would allow strong carbon storage increments if compensated by carbon rent. Application of nonproportional carbon rent is proposed.

[Background] Previous research achievements of the service-oriented tourist city network have often focused on the analysis of its geographical distribution and service role of the important cities instead of the connections and hierarchical tendencies between the whole city in a large region.[Method]Using big data approaches on the regional connections of 38 tourism organizations including famous hotels, air passenger transport, tourism service agencies across 63 most important tourist cities in China. Fuzzy c-means clustering analysis is used to define 8 city arena clusters. [Results]According to the distributions of connectivity between 63 cities, these eight clusters play different service functional roles in the urban tourism network at four hierarchies. With their “center-edge” memberships, these arena clusters are formed by the interweaving process of regional and hierarchical tourism service connections. The results include the analysis of the various service-oriented tourist city in China and point out the geography “gap” faced by network. [Conclusion] Service-oriented tourist cities need to find their hierarchies and positioning in the network scientifically to avoid blind development, to make regional urban tourism sustainable development.

We propose a novel data hiding method in an audio host with a compressive sampling technique. An over-complete dictionary represents a group of the watermark. Each row of the dictionary is a Hadamard sequence representing multiple bits of the watermark. Then, the singular values of segment-based host audio in a diagonal matrix multiply by the over-complete dictionary producing a lower size matrix. At the same time, we embed the watermark into the compressed audio. In the detector, we detect the watermark and reconstruct the audio. This proposed method offers not only hiding the information but also compressing the audio host. The application of the proposed method is a broadcast monitoring and biomedical signal recording. We can mark and secure the signal content by hiding the watermark inside the signal while we compress the signal for memory efficiency. We evaluate the performance in terms of payload, compression ratio, audio quality, and watermark quality. The proposed method can hide the data imperceptibly, in range 729-5292 bps with compression ratio 1.47-4.84 and perfect detected watermark.

The expense of carbon sequestration in terms of capital return deficiency is investigated at estate level, in the case of a fertile boreal estate dominated by spruce forest. Thinnings from below result as a high expense of increased rotation age, thinnings from above as a small expense. The expense of increased timber stock is greater than any proportional carbon rent based on present carbon prices. Application of non-proportional carbon rent is proposed.

The purpose of this paper is to explore which financial performance indicators (FPIs) evaluate the level of supply chain capability (SCC) that explicitly touches all of the business functions and processes within and beyond the company. The authors investigated nine FPIs that were selected from the financial statements of 155 companies within nine industries. The authors find that suitable FPIs to measure SCC for shareholders’ value are return-on-assets (ROA), days-sales-outstanding (DSO), and current ratio (CR). This means that higher ROA, shortened DSO, and an appropriate level of CR could reach a sustainable supply chain. These results will help the industry to avert a major disruption in supply chain processes and activities using suitable financial performance indicators.

Public participation is significant for the success of any urban planning project. However, most members of the general public are not planning professionals and may not understand the technical details of a 2D paper-based plan, which might hamper their participation. One way to expand the participation of citizens is to present plans in well-designed, user-friendly and interactive platforms that allow participation regardless of the technical skills of the participants. This paper investigates the impacts of the combined use of 3D visualization and E-participation on public participation in Kisumu, Kenya. A 3D City model, created with CityEngine2016, was exported into a web-based geo-portal and used as a Planning Support System in two stakeholder workshops in order to evaluate its usability. For e-participation, 300 questionnaires given out to planning practitioners. Five indicators were developed for evaluating the usability of the 3D model while the usability of e-participation was evaluated using communication, collaboration and learning as indicators. Results showed that effectiveness and efficiency varies within different professional groups while the questionnaires showed strong preference for e-participation methods, especially SMSs/USSDs and emails. The study concludes that the use of 3D visualization and E-participation has the potential for improving the quality and quantity of public participation and recommends further research on the subject.

In table tennis competitions the rule violation judgment with the greatest controversy is the height of the ball serve. This is because inaccuracy in the ball height judgment, which results in erroneous judgment, is unavoidable. Thus, we designed an automatic image judgment auxiliary system for table tennis ball height during service in this study. We used a high-speed camera to record the ball toss in the table tennis service. The designed algorithm architecture can automatically search for the ball and the position of the hand action under low light source conditions. The algorithm is mainly divided into hue-saturation-value color space processing and morphology processing using Hough transform to search for the circular ball. Experiment result shows that color segmentation can successfully and accurately determine the ball position under low light conditions. The morphology method can find the position of the hand and help determine the moment when the ball leaves the hand during the service ball toss. Finally, the actual size of the target is used to estimate the actual distance unit represented by the image pixel.

Excessive vibration of temporary grandstand owing to crowd has lateral rhythmic motions can cause human in panic, which attracted increasing attention in recent years. This paper focuses on experiments that a temporary grandstand occupied 20 participants is oscillated by a shaking table with a series of random waves and induced by crowd with rhythmic swaying motions at lateral direction, respectively. And then a series of vibration perception questionnaires about crowd reaction are obtained. Evaluation of annoying level derives in concept of degree of membership and annoying rate method is proposed, then the human health risk of vibration serviceability of temporary grandstand is assessed with acceleration vibration dose value(VDV). From these results it is clear that standing crowd is more tolerant to vibration than seated crowd. The measured vibrations generated by crowd activities on temporary grandstand can cause panic in crowd. New relationship between the annoyance rate and structural acceleration VDV at logarithmic coordinate is proposed. The findings of this study can be utilized to manage the vibration of temporary grandstand and assess the human health risk.

High-entropy alloys have attracted widespread attention from researchers worldwide due to their unique microstructure and outstanding mechanical properties, making them a prominent focus in the field of metallurgy. Among the various high-entropy alloys, the CoCrCuNi system was among the first alloys discovered, and it has shown significant progress in development. By employing different preparation and heat treatment processes, researchers have obtained alloys with diverse performances. The addition of various alloying elements or other components can lead to pronounced variations in the properties of CoCrCuNi high-entropy alloys. This work provides a comprehensive review of recent research progress on CoCrCuNi high-entropy alloys both domestically and internationally. It covers the preparation methods, thermodynamic and kinetic simulation calculations, as well as discussions on heat treatment processes and the influence of alloying elements on the microstructure and mechanical properties of CoCrCuNi high-entropy alloys. Finally, the review concludes with a prospective analysis and predictions for the potential applications and future directions in developing novel high-entropy alloys.

This study investigates the microstructural evolution and mechanical properties of high-nickel shipbuilding steel during thermal processing using High Temperature Confocal Laser Scanning Microscopy (HTCLSM). The in-situ observation of the heating and holding processes reveals critical insights into phase transformations, grain growth behavior, and the formation of precipitates. The experimental results demonstrate that austenitization begins at approximately 700°C, with significant grain boundary nucleation. At 900°C, the formation of black precipitates was observed, and their persistence up to temperatures exceeding 1000°C was confirmed. Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) analyses identified these precipitates as chromium carbides (Cr7C3), which significantly contribute to the material's strength. The comprehensive analysis using Transmission Electron Microscopy (TEM) confirmed the presence and distribution of Cr7C3 within the grains and along grain boundaries. These findings provide a deeper understanding of the microstructural dynamics in high-nickel steels, guiding the optimization of heat treatment processes to enhance mechanical properties for maritime applications.

Knee osteoarthritis (KO) is an important health condition, affecting one third of the people aged 65 years or more. Pain is the main cause of disability. Pain management in KO includes pharmacological and non-pharmacological modalities. Patient education, lifestyle changes, physical exercise and physical agents are prescribed as a first approach for pain control. Laser therapy is part of many therapeutical protocols, with two forms, low-level laser therapy (LLLT) and high-intensity laser therapy (HILT). The paper aimed at stressing the advantages of HILT, based on a greater wavelength, higher energy delivery and deeper tissue penetration. Research on 23 published trials revealed that analgesic effect is rapid, cumulative and long lasting. Compared to sham, to LLLT or to other associations of therapeutical modalities, HILT provided significantly better results on pain reduction and functional improvement. Ultrasound examination showed reduction of intraarticular inflammation.

(1) Background: The purpose of this study was to assess the external load demands in futsal, con-sidering both home and away matches and their outcomes, in order to plan microcycles throughout the season based on the external load of each match. (2) Methods: The external load of 10 players from a First Division team in the Spanish Futsal League was recorded. The total dura-tion of player involvement with the clock stopped was 18.15 ±7.04 minutes. The players' external load was monitored using OLIVER devices. To analyse the influence of the match outcome and location on the external load, a univariate general linear model (GLM) analysis was conducted. (3) Results: There are no differences between the variables, except for accelerations of 2 to 3 m/s² (m) per minute and the number of accelerations of 2 to 3 m/s² per minute. Despite not showing significant differences, there is a trend indicating a higher demand for external loads in away matches as well as in matches won. (4) Conclusions: These findings are important for planning microcycles and providing the appropriate dosage to each player to achieve optimal performance in matches.

Active galactic nuclei (AGNs), either radio-quiet or radio-loud, had never been observed in X-ray polarized light until the advent of the Imaging X-ray Polarimetry Explorer (IXPE [1]) in the end of 2021. This satellite opened a new observational window for studying supermassive black holes and their complex environment. In this regard, radio-quiet AGNs are probably better targets than radio-loud objects to probe accretion processes, due to the lack of synchrotron emission from jets that can dilute the polarized signal from the central engine. Their relatively clean environment not only allows to detect and measure the X-ray polarization originating from the hot corona responsible for X-ray emission, but also to assess the geometry of the media immediately surrounding the supermassive black hole. Such geometrical measurements work just as well for characterizing the corona morphology in pole-on AGNs as it does for determining the three-dimensional shape of the circumnuclear cold obscurer (the so-called torus) in edge-on AGNs. In this review paper, we will return to each of the observations made by IXPE so far in the field of radio-quiet AGNs and highlight the fundamental contribution of X-ray polarimetry to our understanding of how light is emitted and how matter is shaped around supermassive black holes.

(1) Background:The objective of this study was to explorethe dynamic changes of gut microbiota in Simmental calves before weaning, and compared microbial composition and functionality differences between diarrhea and health calves; (2) Methods: Fourteen neonatal Simmental calves were divided into a health group (n = 8) and diarrhea group (n = 6). The rectal stool samples were collected from each calf on days 1, 3, 5, 7, 9, 12, 15, 18, 22, 26, 30, 35, and 40. The high-throughput sequencing analysis of the 16S rRNA gene V1–V9 region was conducted to explore the changes in gut microbiota over time in both groups and assess the influence of diarrhea on microbiota structure and function; (3) Results: E.coli, B.fragilis, and B.vulgatus were the top three bacterial species of pre-weaning Simmental calves.Meanwhile, the major functions of fecalmicrobiota included the “Metabolic pathways”,“Biosynthesis of secondary metabolites”,“Biosynthesis of antibiotics”, “Microbial metabolism in diverse environments”, and “Biosynthesis of amino acids”. For calves in health group, PCoA revealed that the bacterial profiles generated from days 1, 3, 5, 7, and 9 separated from days 15, 18, 22, 26, 30, 35, and 40. While the microbial profiles of calves on day 12 crossed with both clusters, suggesting that the dynamic changes of microbial structures with the increasing of ages. When compared the difference of the relative abundance of bacteria between calves in health and diarrhea groups, the results showed that the relative abundance of the beneficial L.johnsonii, F.prausnitzii, and Limosilactobacillus in the health group were significantly higher than those in the diarrhea group (p

There are four types of influenza viruses: A, B, C, and D. Cattle are susceptible to influenza D infection and serve as a reservoir for this seven-segmented influenza virus. It is generally thought that bovines are not a host of other types of influenza viruses including type A. This long-standing viewpoint has been challenged by the recent highly pathogenic avian influenza (HPAI) H5N1 outbreaks in dairy cows in the United States. To date, HPAI H5N1 has spread into nine states affecting 49 dairy herds and causing clinical symptoms including reduced appetite, fever, and a sudden drop in milk production. This review article describes the current epidemiological landscape of HPAI H5N1 in U.S. dairy cows and the recent interspecies transmission events of HPAI H5N1 in other mammals reported in other countries. The review also discusses adaptation mutations of HPAI H5N1 to mammalian hosts and vaccination strategies. Finally, it summarizes some immediate questions that need to be addressed towards a better understanding of infection biology, transmission, and immune response of HPAI H5N1 in bovines.

Background: Restorative materials might significantly affect load transmission at peri-implant bone. The aim of the present study is to evaluate the shock absorption capacity of two different polymeric materials to be used as frameworks for implant-supported prostheses. Methods: A masticatory robot was used to compare the shock absorption capacity of polyether-ketoneketone (PEKK) Pekkton®ivory (Cendres+Mètaux) and glass fiber-reinforced composite (GFRC) TRINIATM (Bicon). Five identical sample crowns for each of the materials was tested un-der the same conditions described in previously published papers (Menini et al. 2013). Forces transmitted at the simulated periimplant bone were recorded and statistically analysed. Results: The statistical analysis of forces transmitted at the simulated dental implant revealed significant differences between all the materials tested and significant differences with the mate-rials tested in a previously published paper (Menini et al. 2013: zirconia, glass ceramic, composite resin, acrylic resin). Only differences between PEKK and veneered PEKK and between PEKK and one of the previously tested composite resins were not statistically significant. PEKK samples demonstrated significantly greater shock absorption capacity compared to GFRC. Conclusions: PEKK revealed optimal shock absorption capacity. Further studies are needed to evaluate its efficacy in case of long span prostheses with reduced prosthetic volume.

Two novel members of the subfamily Betarhabdovirinae, family Rhabdoviridae, were identified in Brazil. Overall, their genomes have the typical organization 3’-N-P-P3-M-G-L-5’ observed in mono-segmented plant-infecting rhabdoviruses. In aristolochia-associated cytorhabdovirus (AaCV), found in the liana aristolochia (Aristolochia gibertii Hook), an additional short orphan ORF encoding a transmembrane helix was detected between P3 and M. AaCV genome and deduced encoded proteins share the highest identity values, consistently < 60%, with their counterparts of yerba mate chlorosis-associated virus (Cytorhabdovirus flaviyerbamate). The second virus, false jalap virus (FaJV), was detected in the herbaceous plant false jalap (Mirabilis jalapa L.) and represents together with tomato betanucleorhabdovirus 2, originally found in tomato plants in Slovenia, a tentative new species of the genus Betanucleorhabdovirus. FaJV particles accumulate in the peri-nuclear space, and electron-lucent viroplasms were observed in the nuclei of the infected cells. Notably, distinct from typical rhabdoviruses, most virions of AaCV were observed to be non-enclosed within membrane-bounded cavities. Instead, they were frequently seen in close association with surfaces of mitochondria or peroxisomes. Unlike FaJV, AaCV was successfully graft-transmitted to healthy plants of three species of the genus Aristolochia, while mechanical and seed transmission proved unsuccessful for both viruses. Data suggest that these viruses belong to two new tentative species within the subfamily Betarhabdovirinae.

High gravity brewing (HGB) and adjunct use are common practices in industrial breweries. This work studied the impact of HGB and wheat adjuncts on beer characteristics. Parameters were evaluated in full-malt beer and beers prepared with 30 % wheat grits (WG) and wheat flakes (WF) in the grist and the effect of HGB was examined. Five beers were prepared; one control, two with different original gravity (OG) with WF and two with WG. Beers with higher OG were diluted to a lower OG and control beer was prepared too. The application of wheat adjuncts increased foam stability but HGB did not affect the beer foam. HGB beers had a remarkably higher ester concentration than other samples, and beers with WG also had a significantly higher ester content. Decreased higher alcohols to esters ratio in HGB beers affected the balanced flavour profile of the lager beer. There was a significantly lower content of unwanted volatiles such as vicinal diketones and dimethyl sulphide in HGB beers. The application of HGB mostly did not affect the beer ageing characteristics such as carbonyl compounds and thiobarbituric acid number.

In this study, alfalfa silage with different packing densities (500 kg/m3, 600 kg/m3 and 700 kg/m3) were set up under outdoor high temperature and indoor normal temperature. The chemical composition, fermentation quality and microbial community of alfalfa silage were analyzed. The results showed that DM and WAC content decreased with the increase of density. When the density is 600kg/m3, CP content reaches the maximum and ADF content is the lowest. Temperature has a certain effect on alfalfa silage. The content of Lactobacillus plantarum fermented at high temperature is lower than that fermented at normal temperature. At the same time, the content of Lactobacillus plantarum decreased with the increase of packing density. However, the content of Lactobacillus plantarum was the lowest when the packing density was 600 kg/m3 at high temperature. In summary, this study explained the effects of different temperature and density on alfalfa fermentation quality and microbial community, and clarified that the density should be reasonably controlled within 600 kg/m3 during alfalfa silage, providing theoretical support for production practice.

This work presents a unique two-element high-isolated orthogonally CPW-fed UWB Multiple Input Multiple Output (Ultra-wideband) antenna. The antenna is supported by the 52.8 × 29 mm2 FR-4 substrate, which has a dielectric constant of 4.3 and a thickness of 1.6 mm. The suggested MIMO antenna reduces mutual coupling by separating the two single UWB antennas that make up the antenna. The suggested antenna achieves a voltage standing wave ratio (VSWR) of less than two and more than 86% radiation efficiency over the whole range of interest. The antenna's performance is assessed using both modeling and experimentation. Return loss, efficiency, gain, bandwidth, and Voltage Standing Wave Ratio (VSWR) are all factors in which the design performs well. The suggested antenna is evaluated using the CST Microwave Studio. The antenna prototype model is constructed, tested, and measured in order to validate the simulation return-loss results. There is good agreement between the measured and simulated results.

Landscape changes based on spectral responses allow showing plant cover changes through diversity, composition, and ecological connectivity. The spatial and temporal vegetation dynamics of the Bijagual Massif from 1986 to 2021 were analyzed as a measure of ecological integrity, conservation, and territory. The covers identified were high open forest (Hof), dense grassland of non-wooded mainland (Dgnm), a mosaic of pastures and crops (Mpc), lagoons (Lag), and bare and degraded lands (Bdl). The Bijagual Massif has 8,574.1 ha. In 1986, Dgnm occupied 42.6% of the total area, followed by Mpc (32.8%) and Hof (24.5%); by 2000, Mpc and Hof increased (43.7 and 28.1%, respectively), while Dgnm decreased (28%); by 2021, Dgnm was restricted to the northeastern zone and continued to decrease (25.2%), Mpc occupied 52.9%, Hof 21.7% and Bdl 0.1%. Of the three fractions of the connectivity probability index, only dPCintra and dPCflux contribute to ecological connectivity. Hof and Dgnm show patches with biota habitat quality and availability. Between 1986 and 2021, Dgnm lost 1,489 ha (41%) and Hof 239.5 ha (11%). Mpc replaced various covers (1,722.2 ha; 38%) in 2021. Bijagual has a valuable biodiversity potential limited by Mpc. Territorial planning and sustainable agroecological and ecotourism proposals are required due to the context of the ecosystems.

Runaway electrons (RAEs) generation in high-pressure gases is an important physical phenomenon that influences significantly discharge shapes and properties of initiated plasma. The diffuse discharges formed due to RAEs in air and other gases at atmospheric pressure find wide application. In the present review, theoretical and experimental results that explain the reason for the RAEs occurrence at high pressures are analyzed and recommendations are given on the implementation of conditions under which the runaway electron beam (RAEB) with the highest current can be obtained at atmospheric pressure. Experimental results were obtained using subnanosecond, nanosecond, and submicrosecond generators, including those specially developed for runaway electron generation. The RAEB were recorded by oscilloscopes and collectors with picosecond time resolution. To describe theoretically the phenomenon of continuous electron acceleration, the method of physical kinetics has been used based on the Boltzmann kinetic equation that takes into account the minimum but sufficient number of elementary processes, including shock gas ionization and elastic electron scattering. Results of modeling allowed the main factors to be established that control the RAE appearance, the most important of which is electron scattering on neutral atoms and/or molecules. Theoretical modeling has allowed the influence of various parameters (including the voltage, pressure, gas type, and geometrical characteristics of the discharge gap) to be taken into account. The results of research presented here allow the RAEs accelerators with desirable parameters to be developed and the possibility of obtaining diffuse discharges to be accessed under various conditions. The review consists of the Introduction, 5 Sections, the Conclusion, and the References.

This paper presents the experimental campaign conducted near the Condoroma dam at 4075 m a.s.l. in an experimental setup consisting of a series of standard profile spillways with a vertical upstream face of up to five different dimensionless heights (P/Hd). The experimental results indicate that for all P/Hd ratios studied, the discharge coefficients adjusted to the Condoroma altitude are lower than those reported by classical formulations used in conventional spillway design. As a result, a generalized equation is proposed to estimate the discharge coefficient for standard spillways located in dams at similar elevations above sea level.

With nearly 1,700 species, Microsporidia represent a group of obligate intracellular eukaryotes with veterinary, economic and medical impacts. To help in understanding the biological functions of these microorganisms, complete genome sequencing is used routinely. Nevertheless, the proper prediction of their gene catalogue is challenging due to taxon-specific evolutionary features. As innovative genome annotation strategies are needed to obtain a representative snapshot of the overall lifestyle of these parasites, the MicroAnnot tool, a dedicated workflow for microsporidian sequence annotation using data from curated databases of accurately annotated microsporidian genes, has been developed. Furthermore, specific modules have been implemented to perform small genes (&lt; 300bp) and transposable element identification. Finally, functional annotation was performed using the signature-based InterProScan software. MicroAnnot’s accuracy has been verified by the re-annotation of four microsporidian genomes for which structural annotation had previously been validated. With its comparative approach and transcriptional signal identification method, MicroAnnot provides accurate prediction of translation initiation sites, efficient identification of transposable elements, as well as high specificity and sensitivity for microsporidian genes including those under 300 bp. Thanks to its web interface (https://microannot.org), MicroAnnot is available to the community to ensure high quality annotation of microsporidian genomes.

(1) Background: Lifestyle changes, eventually associated with a nutraceutical, are recommended strategies for managing high-normal blood pressure (BP) patients with low-moderate cardiovascu-lar (CV) risk. Nitrates-enriched products (i.e., red beet extracts) may help reduce BP, exerting vas-oactive properties and enhancing adherence to lifestyle advice. Our study aimed to evaluate the effectiveness in clinical practice of generic written lifestyle advice and a beetroot-based nutraceu-tical prescription based on the 2018 ESC/ESH guidelines on 24-hour BP in a population with high-normal BP and low-moderate CV risk.; (2) Methods: A longitudinal observational study was con-ducted in two ESH hypertension excellence centres on 43 consecutive subjects with high-normal BP based on repeated office BP (OBP) measurements and a low-moderate CV risk. Twenty-four-hour ambulatory BP monitoring (ABPM) was carried out at baseline and three months after ge-neric written ESC/ESH advice for lifestyle changes associated with a nutraceutical containing 500 mg of dry beetroot extract; (3) Results: Mean age 50±11 years, 54% males, 58% overweight/obese, mean OBP 135±3/85±3 mmHg. At baseline, 24-hour BP, daytime BP and night-time BP were 127±7/80±6 mmHg, 131±8/83±6 mmHg and 118±8/70±5 mmHg, respectively, BP profiles compat-ible with hypertension status in some subjects. After a median follow-up of 98 (92-121) days, all BPs, except night-time diastolic BP, were significantly decreased: -3±6/-2±4 mmHg for 24-hour BP, -3.9±6.0/-3.0±4.0 mmHg for daytime BP and -3.3±7.4/-1.3±4.7 mmHg for night-time BP, respec-tively. No significant clinical changes in weight were detected. BP decreased independently of baseline BP level, gender, smoking status and BMI, while a more substantial decrease in BP was observed in older patients; (4) Conclusions: Our pilot study shows for the first time that written generic lifestyle advice based on ESC/ESH hypertension guidelines coupled with a beetroot-based nutraceutical may represent a valid initial non-pharmacological approach in subjects with high-normal BP and low-moderate CV risk even without personalized diet interventions.

Infrastructure and urban network operators, city users and industrialists are faced with complex issues to ensure the sustainability of the service, maintain, operate and develop their urban systems, while integrating environmental, economic and societal impacts and being resilient to unexpected geopolitical and climatic upheavals. Digital Twins are now recognized as the cornerstone of digital transformation. In the field of smart cities, they can enable all stakeholders to collaborate across disciplinary silos and foster digital transformation in urban and territorial projects to ensure sustainability, resilience and increased inventiveness. However, the application of the Digital Twin technology to Smart Cities lacks of standards. This paper proposes a high-level architecture for Digital Twins as an enabler of various levels of interoperation between key stakeholders of a Smart City. Such a technology-agnostic architecture, when implemented for a given Smart City, produces a middleware for large scale interoperability between actors involved in multiple supply chains of this territory.

Early-life exposure to high-fat diet (HF) can program metabolic and cognitive alterations in adult offspring. Although the hippocampus plays a crucial role in memory and metabolic homeostasis, few studies reported the impact of maternal HF on this structure. We assessed the effects of maternal HF during lactation on physiological, metabolic and cognitive parameters in young adult offspring mice. To identify early-programming mechanisms in hippocampus, we developed a multi-omics strategy in male and female offspring. Maternal HF induced a transient increased body weight at weaning, a mild glucose intolerance only in 3-month-old male mice with no change in plasma metabolic parameters in adult male and female offspring. Behavioral alterations revealed by Barnes maze test were observed both in 6-month-old male and female mice. Multi-omics strategy unveiled sex-specific transcriptomic and proteomic modifications in the hippocampus of adult offspring. These studies that were confirmed by regulon analysis, showing that, although genes whose expression was modified by maternal HF were different between sexes, the main pathways affected were similar with mitochondria and synapses as main hippocampal targets of maternal HF. The effects of maternal HF reported here may help to better characterize sex-dependent molecular pathways involved in cognitive disorders and neurodegenerative diseases.

The high protein content of several microalgal species makes them attractive and unconventional for applications in the food and pharmaceutical industries. Due to microalgae's robust cell wall, cell rupture is necessary to improve the extraction of their intracellular proteins. Thus, choosing a suitable cell-breaking treatment before protein extraction is a vital downstream processing step. Additionally, it is necessary to use an effective technique for monitoring and measuring the impact of rupture treatments on microalgal cell walls. In our study, Tetradesmus obliquus cells were disrupted by three different mechanical rupture methods: high-pressure homogenization (HPH), ultrasound (US), and ball milling (BM). The ruptured biomass cells were counted, and soluble proteins were extracted and quantified. The cell counting technique did not detect differences between intact and damaged cells after BM treatment because the dye (erythrosine B) did not permeate the microalgae biomass accurately. The US treatment promoted the highest yield of total protein extraction (19.95%). The yields of protein extraction of T. obliquus with HPH (15.68%) and BM (14.11%) were significantly (p value ≤ 0.05) lower than that achieved in the US treatment. The increase in the number of extraction steps increased the protein recovery. Thus, the content of extracted soluble protein was a reliable indirect index for a quantitative comparison of the cell disruption level.

This study deals with two different aspects of the high-strength low-alloyed 1100 MC steel. The first is associated with the remarkable heterogeneity in the surface state produced during sheet rolling with respect to the sheet width. The variable-thickness surface layer exhibits a microstructure different from that of the deeper bulk. Variation of the thickness of the thermally softened near-surface region strongly affects Barkhausen noise, as well. This technique can be considered a reliable tool for monitoring the aforementioned heterogeneity. It can also be reported that the opposite sides of the sheet are different with respect to the surface state, heterogeneity distribution, and corresponding Barkhausen noise. These aspects indicate the different conditions during hot rolling followed by rapid quenching on the upper and lower rollers. The second aspect is related to the remarkable asymmetry of Barkhausen noise emission with respect to two consecutive bursts. This asymmetry is due to the presence of remnant magnetisation in the sheet produced during manufacturing. The remnant magnetisation is coupled to the magnetic field produced by the excitation coil of the Barkhausen noise sensor and strongly contributes to the aforementioned asymmetry. As soon as sufficient removal of this remnant magnetisation is carried out in the vanishing magnetic field (demagnetisation), the aforementioned remarkable asymmetry is fully lost.

Accretionary and collisional orogeny are often accompanied by the disturbance of the geothermal gradient, leading to high-temperature metamorphism. High-temperature metamorphic rocks are significant in their ability to help the reconstruction of the thermal histories of orogenic belts. The Tianshan Orogenic Belt, at the southwest margin of the Central Asian Orogenic Belt, is a record of the long-term subduction–collision–post-collision orogenic process that has taken place in the Phanerozoic Eon. Here, we report the discovery of mafic granulites in the Muzhaerte area, SW Tianshan. Petrographic observation reveals that the mafic granulites underwent two metamorphic stages. The peak mineral assemblages of the first stage are dominated by clinopyroxene + orthopyroxene + plagioclase + quartz + hornblende ± biotite, and the post-peak mineral assemblages of the second stage are dominated by clinopyroxene + plagioclase + quartz + amphibole + biotite. The calculated results obtained from the two-pyroxene thermobarometers and the Al-in-hornblende barometer for the mafic granulites indicate that the metamorphic conditions of mafic granulites are 760–860 ℃ and < 0.39–0.41 Gpa. The mafic granulites recorded a high-grade granulite facies thermal metamorphic event with the highest temperature limit currently recorded in the Central Tianshan Block.

In this paper, COMSOL Multiphysics software was used to simulate and analyze the process of cleaning oily sludge by high-speed stirring rotor. The physical phenomena such as velocity field, pressure field, heat dissipation and cavitation generated by the rotor during the process of the oily sludge cleaning were analyzed. The results showed that in the process of cleaning the oily sludge by high-speed stirring rotor, the shear force, heat dissipation and pressure increased with the enhance in the rotor speed. Cavitation occurs in the impeller area of the rotor because of the change of pressure, so the cavitation bubbles were formed. Shear force, heat dissipation and cavitation contributed to the separation of oil phase in oily sludge. Meanwhile, the simulation results were verified by experiments.

The purpose of the current study was the level of the self-confidence among with high musical abilities Student? The randomly selected sample consisted of students (n= 130, M= 65, F= 65) . The analytical descriptive approach was applied in the study and self-confidence Scale developed by the author was administered to participants. Results indicated that: - The self-confidence among the high musical abilities Student students was rated high. There were no statistically significant differences at (α=≤0.05) attributed to effect of sex on the self-confidence overall degree. There were statistically no significant differences at (α≤0.05) attributed to effect of achievement on the self-confidence overall degree,

The coronaviral pandemic has led to a shift in traditional teaching methods to more innovative approaches, such as high-fidelity patient simulation (HFPS), which can improve students’ clinical judgement and decision-making for quality patient care. A modified guideline was introduced to enhance students’ satisfaction and self-confidence in learning through HFPS. The study involved 189 baccalaureate nursing students, with 92 in the intervention group and 97 in the control group. The intervention group received the modified HFPS guideline, while the control group received standard treatment with basic instruction. After the HFPS debriefing session, students provided narrative feedback on their learning experience. The quantitative results showed that students in the intervention group reported a significant improvement in satisfaction and self-confidence in learning compared to the control group. The modified HFPS guideline provided clear guidance for students to learn and apply knowledge and skills more effectively, leading to increased engagement during interactive simulation sessions. The results suggest that the HFPS guideline should be added to the curriculum to enhance students’ satisfaction and self-confidence in learning, even in junior students. Innovative teaching methods, such as HFPS, can be necessary and beneficial for healthcare professional training, after the pandemic.

The popularity and growth of additive manufacturing(AM) in recent years are due to its ability to provide innovative solutions to complex manufacturing challenges and its potential to transform the way products are designed, developed, and produced. In this work, the numerical simulation geometry of the model extruder from nozzle is established along with the material extrusion process. The high gravity material extrusion system (HG-MEX) properties and characteristics during filament fabrication are evaluated. This work investigates the effects of gravity on the material extrusion process from nozzle extrusion. This work is unique in the incorporation of fluid surface characteristics to represent the performance and contact with the material extrusion in additive manufacturing. The use of simulation in high gravity material extrusion in additive manufacturing is a meaningful and valuable approach to improving the quality and efficiency of the process.

Hessenberg differential algebraic equations (Hessenberg-DAEs) with high index play a critical role in the modeling of mechanical systems and multibody dynamics. Motivated by the widely used Lie Group Differential Algebraic Equation (LGDAE) method which only handles index 2 systems, we propose a Modified Extended Lie Group Differential Algebraic Equation (MELGDAE) method for solving index 3 Hessenberg-DAEs, and provide theoretical analysis to deepen the foundation of the MELGDAE method.The performance of the MELGDAE method is compared with the standard methods RADAU and MEBDF on index 2 and 3 DAE systems, and it is demonstrated that the MELGDAE integrator exhibits competitive performance in terms of high accuracy and the preservation of algebraic constraints. In particular, all differential variables in index 3 Hessenberg DAEs achieve second-order convergence using the MELGDAE method, which suggests potential for extension to Hessenberg-DAEs with an index of 4 or higher.

This study assessed the literature about the use of high tunnels (HTs) in agricultural systems in the United States since the 2009 launch of the Natural Resources Conservation Service (NRCS) High Tunnel Initiative. This NRCS program led to an increase in HT adoption nationwide. The literature searches were conducted using the Web of Science (WoS) database. The final sample was 133 peer-reviewed articles published between 2009 and February 2023. We used CiteSpace 6.2.R1 and Gephi 0.9.2 to conduct co-citation, co-author, co-institution, and clustering techniques. The findings showed that the peer-reviewed literature about HT use has increased since 2009, substantially rising between 2017 and 2021. Horticulture was the top subject category in the literature, and most articles were published in peer-reviewed journals of the American Society for Horticultural Science (i.e., HortTechnology and HortScience). The research field evolved from general HT practices, nutrient management, and plant pathology to focus on trials of specific crops and integrated pest management. The institutions with the most contributions to the HT literature were Kansas State University, the University of Florida, Michigan State University, Purdue University, and the University of Minnesota. The patterns of HT research revealed in this study offer a greater understanding of the current state of knowledge to inform the focus of future research.

The overcrowding of high-rise buildings in the city adversely affects the wind environment by changing the air currents in the surrounding areas. In particular, extreme climate phenomena caused by climate change are stronger and more frequent, causing social damages in cities. To comprehensively better understand the wind properties around high-rise buildings, actual filed measurement is necessary to determine the environment assessment of wind effect. We performed the on-site measurement on LCT residential complex regions (411.6m tall) with highly concentrated high-rise buildings in coastal city Busan, South Korea under extreme weather conditions such as typhoon invasions to determine wind fluid characteristics. In the field monitoring, five anemometers were installed to analyze the wind environment around high-rise buildings when typhoon 'Hinnamnor' invaded. Compared to the nearby weather station operated by KMA(Korea Meteorological Administration), the gust was 3.7 times stronger and the max 1 min-mean wind speed was 3.1 times stronger, and the characteristics of the downward wind and the canyon wind were shown depending on the location characteristics of the point. Turbulence intensity decreased as the wind speed increased and converged to a certain value. Likewise, the gust factor also decreased as the wind speed increased and converged to 2.0, which is considered to be the parameter that best represents the intensity of the instantaneous gust caused by the skyscraper wind effect.

In the context of the Atmospheric Observing System (AOS) international program, a new generation spaceborne lidar is expected to be in polar orbit for deriving new observations of aerosol and clouds. In this work, we analyze the added values of these new observations for characterizing aerosol vertical distribution. For this, synthetic observations are simulated using the BLISS lidar simulator in terms of backscatter coefficient at 532 nm. We consider two types of lidar instruments, an elastic backscatter lidar instrument and a high spectral resolution lidar (HSRL). These simulations are performed with atmospheric profiles from a Nature Run (NR) modeled by the MOCAGE Chemical Transport Model. In three case studies involving large events of different aerosol species, the added value of the HSRL channel for measuring aerosol backscatter profiles with respect to simple backscatter measurements is shown. Observations independent from an a-priori lidar Ratio assumption, as done typically for simple backscattering instruments, allows probing the vertical structure of aerosol layers without divergence, even in case of intense episodes. Relative error in the backscatter coefficient profiles are observed to lay between +40% and -40% for low abudancies, with mean biases between +5% and -5%. A 5-day study in the case of desert dust completes the study of the added value of the HSRL channel with relative mean bias from the NR of the order of 1.5%.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

The temperature-assisted laser shock process has shown promising prospects in the fields of forming manufacturing and surface strengthening. However, large-scale application of this process is limited by the instability and failure of confinement medium at high temperatures (≥300 ℃). Aiming at this problem, we propose a novel laser shock strategy based on Leidenfrost effect, where the suspended droplets are utilized as the confinement medium. According to the sequence of images acquired by time delay system and high-speed camera, the droplet dynamics behavior is studied. The focusing enhancement effect of the droplet is comprehensively explored. And the correlations between droplet size, ambient temperature, vapor layer thickness and focusing effect are investigated. Combining the dynamics and focusing enhancement effect of droplets, a theoretical model of laser shock pressure under droplet confinement is established. Finally, the effectiveness and feasibility of the droplet-based laser shock strategy in high temperature processing environments are verified by typical applications in laser shock forming and laser shock peening fields. The results show that the droplet-based laser shock process presents better forming effect. And the mechanical property tests demonstrate that this process can obtain the simultaneous improvement of the strength (~51%) and ductility (~6.4%) of annealed Cu. The multiscale plasticity mechanisms of the strengthened material are comprehensively investigated. We believe that this low-energy, low-cost and high-quality process can provide a new solution for the industrial application of laser shock at high temperatures.

To realize precise control of the quantum dots (Qdots) device, multi-channel precision bias source plays the key role. In this paper, the 16-channel high precision bias source with 18-bit resolution for Qdots device was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The step response time is less than 3μs. The resolution, stability, linearity and dynamic range of the bias source exhibits good performance. What's more, the bias source can be controlled locally and online. The results show that it is one effective and feasible topology for experiments in Qdots device application.

High temperatures (HT) and high hydrostatic pressures (HHP) are characteristic of deep-sea hydrothermal vents and other deep crustal settings. These environments host vast and diverse microbial populations, yet only a small fraction of those populations have been successfully cultured. This is due, in part, to the difficulty of sampling while maintaining these in situ conditions and also replicating those high-temperature and high-pressure conditions in the laboratory. In an effort to facilitate more HT-HHP cultivation, we present two HT-HHP batch culture incubation systems for cultivating deep-sea vent and subsurface (hyper)thermophilic microorganisms. One HT-HHP system can be used for batch cultivation up to 110 MPa and 121°C, and requires sample decompression during subsampling. The second HT-HHP system can be used to culture microorganisms up to 100 MPa and 160°C with variable-volume, pressure-retaining vessels that negate whole-sample decompression during subsampling. Here, we describe how to build cost effective heating systems for these two types of high-pressure vessels, as well as the protocols for HT-HHP microbial batch cultivation in both systems. Additionally, we demonstrate HHP transfer between the variable-volume vessels, which has utility in sampling and enrichment without decompression, laboratory isolation experiments, as well as HHP filtration.

Abstract: Abstract: The objective of this article is to analyze the dimensions of creativity concerning students with high abilities. Firstly a review of the most relevant scientific contributions on creativity is carried out. Next the dimensions of creativity in secondary school students who have been previously identified as high- ability students are analyzed. Those abilities associated to di-vergent thinking were assessed by means of the Torrance Test of Creative Thinking [19]. The flu-ency, flexibility and originality dimensions were assessed with the Scientific-Creative Thinking Test (TPCC, [7]). The results obtained evidence that high-ability students achieve greater scores in both the figurative creativity and scientific-creativity dimensions. A significant relationship between creativity and high ability can therefore be established. This study is of an exploratory nature and the results obtained contribute to develop future studies in application of its findings in the teaching-learning process..

This paper proposes a forecast-centric adaptive learning model that engages with the past studies on the order book and high-frequency data, with applications to hypothesis testing. In line with the past literature, we produce brackets of summaries of statistics from the high-frequency bid and ask data in the CSI 300 Index Futures market and aim to forecast the one-step-ahead prices. Traditional time series issues, e.g. ARIMA order selection, stationarity, together with potential financial applications are covered in the exploratory data analysis, which pave paths to the adaptive learning model. By designing and running the learning model, we found it to perform well compared to the top fixed models, and some could improve the forecasting accuracy by being more stable and resilient to non-stationarity. Applications to hypothesis testing are shown with a rolling window, and further potential applications to finance and statistics are outlined.

Objective: To study the changes in urine metabolism in female water polo players before and after high-intensity training by using ultra-high performance liquid chromatography-mass spectrometry, and to explore the biometabolic characteristics of urine after training and competition. Methods: Twelve young female water polo players (except goalkeepers) from Shanxi Province were selected. A 4-week formal training was started after one week of acclimatization according to experimental requirements. Urine samples (5 ml) were collected before formal training, early morning after 4 weeks of training, and immediately after 4 weeks of training matches, and labeled as T1, T2, and T3, respectively. The samples were tested by LC-MS after pre-treatment. XCMS, SIMCA-P 14.1, and SPSS16.0 were used to process the data and identify differential metabolites. Results: On comparing the immediate post-competition period with the pre-training period (T3 vs T1), 24 differential metabolites involved in 16 metabolic pathways were identified, among which niacin and niacinamide metabolism and purine metabolism were potential post-competition urinary metabolic pathways in the untrained state of the athletes. On comparing the immediate post-competition period with the post-training period (T3 vs T2), 10 metabolites involved in 3 metabolic pathways were identified, among which niacin and niacinamide metabolism was a potential target urinary metabolic pathway for the athletes after training. Niacinamide, 1-methylnicotinamide, 2-pyridone, L-Gln, AMP, and Hx were involved in two metabolic pathways before and after the training. Conclusion: Differential changes in urine after water polo games are due changes in the metabolic pathways of niacin and niacinamide.

The lipid composition of biomembranes influence the properties of the lipid bilayer as well as that of the proteins. In this study, the lipidome and the lipid/protein ratio of membranes from High FiveTM insect cells overexpressing mouse P-glycoprotein was characterized. This provides a better understanding of the lipid environment in which P-glycoprotein is embedded, and thus of its functional and structural properties. The relative abundance of the distinct phospholipid classes and their acyl chain composition was characterized. A mass ratio of 0.57 +/- 0.11 phospholipids to protein was obtained. Phosphatidylethanolamines are the most abundant phospholipids, followed by phosphatidylcholines. Membranes are also enriched in negatively charged lipids (phosphatidylserines, phosphatidylinositols and phosphatidylglycerols), and contain small amounts of sphingomyelins, ceramides and monoglycosilatedceramides. The most abundant acyl chains are monounsaturated, with significant amounts of saturated chains. The characterization of the phospholipids by HPLC-MS allowed identification of the combination of acyl chains, with palmitoyl-oleoyl being the most representative for all major phospholipid classes except for phosphatidylserines, which are mostly saturated. A mixture of POPE:POPC:POPS in the ratio 45:35:20 is proposed for the preparation of simple representative model membranes. The adequacy of the model membranes was further evaluated by characterizing their surface potential and fluidity.

Melanophryniscus admirabilis (admirable red-belly toad) is a microendemic and critically endangered species found exclusively along 700 meters of the Forqueta River, in a fragment of Atlantic Forest in southern Brazil. One of the greatest concerns regarding the conservation of this species is the extensive use of pesticides in areas near their natural habitat. In recent years, the adaptation and persistence of animal species in impacted environments have been associated with microbiota. Therefore, the current study aimed to characterize the oral bacterial community of wild M. admirabilis and to address the question of how this community might contribute to toad’s adaptation in the anthropogenic environment and its general metabolic capabilities. In the present study, 11 oral samples collected from wild M. admirabilis were characterized and analyzed via high-throughput sequencing. A total of 181,350 sequences were obtained, resulting in 16 phyla, 34 classes, 39 orders, and 77 families. Proteobacteria dominated (53%) the oral microbiota of toads followed by Firmicutes (18%), Bacteroidetes (17%), and Actinobacteria (5%). No significant differences in microbial community profile from among the samples were reported, suggesting that the dietary restriction may directly influence the bacterial composition. Functional inference of microbiome was performed using PICRUSt2 and important pathways, such as xenobiotic degradation pathways to pesticides and aromatic phenolic compounds were detected, suggesting that the bacterial communities may have important roles in M. admirabilis health and survival in the anthropogenic environment. Overall, our results have important implications for the conservation and management of this microendemic and critically endangered species.

This paper presents a numerical algorithm for solving high-order BVPs. We introduce the construction method of multiscale orthonormal basis in W^m[0; 1] by multiscale orthonormal basis in W¹[0; 1]. We define approximate solution, and obtain the approximate solution of high-order BVPs by using the approximate theory. Moreover, the convergence and stability of the algorithm are improved. At last, several numerical experiments show the feasibility of the proposed method.

The complexity of the design in high-rise residential projects is a challenge for the construction industry in completing projects that fit the needs of users. Performance-Based Building Design (PBBD) appears as a design concept that can describe these needs into performance requirements. In this case designing a building can be considered as an iterative process of exploration, where desired functional properties can be created, the shapes are suggested, and evaluation processes is used, so as to bring together the shapes and functions of the building. This concept is a container for designers to produce high-performance buildings. This study aimed to identify the performance-based building design factors applied by architect designers and engineers in high-rise residential building in Surabaya. As part of this study, primary data was collected based on surveys conducted through observation and questionnaire distributed to designers who had or were involved in the high-rise residential design process in Surabaya. A total of sixty-eight respondents were included in this study. Descriptive analysis through a mean and standard deviation scatter plot was used to rank the application of PBBD. Meanwhile, factor analysis was used in the analysis of PBBD application factors. From the results of the analysis, four factors were obtained for the application of PBBD in high-rise residential buildings in Surabaya, namely; the interests of occupants, the sustainability of building operations, the design collaboration process, and the risk of loss. Future research is the influence relationships and measure the success model of PBBD at a higher level into BIM (Building Information Modeling) interoperability.

The exact etiology of myopia remains elusive. The author proposes the particle property of photon in living tissue and the photon-electron theory in living tissue, if the frequency of the photon exceeds the threshold, the photon has enough energy to strike the electron away and forms a hole of a diameter in photon diameter scale in living tissue include the eye. Longer time of high-frequency electromagnetic radiation will cause more holes and a larger radius of holes. The visual light which passes through the radiated hole in the eye cannot be refracted on the macula, this is myopia symptom of blurred vision, shortening the distance of the eye and the object will include more visual light into cornea and lens, this is myopia another symptom of nearsightedness. The particle property of photon causes elongation of the eye and the macular holes.Blue light and X-ray are two kinds of high-frequency electromagnetic radiation which can shot holes in eye and cause myopia.

The purpose of this study was to assess if self-regulation of intensity based on rating of perceived exertion (RPE) is a reliable method to control the intensity of metabolic conditioning of functional-fitness session. In addition, the relationship between RPE and changes in heart rate and lactate responses was also analyzed. Eight male participants (age 28.1 ± 5.4 years; body mass 77.2 ± 4.4kg; VO₂max: 52.6 ± 4.6 mL·(kg·min)⁻¹) completed three randomly sessions (5 to 7 days apart) under different conditions: (1) all-out (ALL); (2) self-regulation of intensity based on a RPE of 6 (hard) on the Borg CR-10 scale (RPE6); and (3) a control session. Rate of perceived exertion, LAC and HR response were measured pre, during and immediately after the sessions. The RPE and LAC during the ALL-OUT sessions were higher (p ≤ 0.05) than the RPE6 and control sessions for all the analyzed time points during the sessions. Regarding HR, the 22 min area under the curve of HR during ALL-OUT and RPE6 sessions were significantly higher (p ≤ 0.05) than the control session. The average number of repetitions was lower (p ≤ 0.05) for the RPE6 session (190.5 ± 12.5 repetitions) when compared to the ALL session (214.4 ± 18.6 repetitions). There was a significant correlation between RPE and LAC (p = 0.001; r = 0.76; very large) and number of repetitions during the session (p = 0.026; r = 0.55; large). No correlation was observed between RPE and HR (p = 0.147; r = 0.380). These results indicate that self-regulation of intensity of effort based on RPE may be a useful tool to control exercise intensity during a metabolic conditioning session of functional-fitness.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

Three-dimensional (3D) cell culture is considered more clinically relevant in mimicking the structural and physiological conditions of tumors in vivo compared to two-dimensional cell cultures. In recent years, high-throughput screening (HTS) in 3D cell arrays has been extensively used for drug discovery because of its usability and applicability. Herein, we developed a microfluidic spheroid culture device (μFSCD) with a concentration gradient generator (CGG) that enabled cells to form spheroids and grow in the presence of cancer drug gradients. The device is composed of concave microwells with several serpentine micro-channels which generate a concentration gradient. Once the colon cancer cells (HCT116) formed a single spheroid (approximately 120 μm in diameter) in each microwell, spheroids were perfused in the presence of the cancer drug gradient irinotecan for 3 days. The number of spheroids, roundness, and cell viability, were inversely proportional to the drug concentration. These results suggest that the μFSCD with a CGG has the potential to become an HTS platform for screening the efficacy of cancer drugs.

Beginning with the discovery of the BRCA ovarian cancer susceptibility genes and subsequent detailed examination of risk reduction salpingo-oophorectomy (RRSO) specimens, a new paradigm of ovarian carcinogenesis has unfolded with attention to the distal fallopian tube. The primary focus has been an early cancer in the fallopian tube which is seen in virtually all incidentally discovered high-grade serous cancers in asymptomatic women. This high-frequency of tubal involvement in early serous cancer - serous tubal intraepithelial carcinoma or STIC - has galvanized attention to this organ as a primary source of this disease. However, an enduring mystery has been the relatively low frequency of STIC in fallopian tubes of women with advanced malignancy. This paradox, a high-frequency of tubal involvement early and a low-frequency late in the disease process has spurred interest in other potential sources, such as the ovarian surface or secondary Mullerian system. However, because essentially all high-grade serous carcinomas are linked by TP53 mutations, and because fallopian tubes frequently contain early serous proliferations (ESPs) with these mutations, attention has turned to the possibility that nonmalignant but TP53 mutated tubal epithelium could be responsible for an eventual malignancy. Recent data have shown evidence of lineage continuity between ESPs and concurrent serous carcinomas prompting the concept of "precursor escape". This creates a 2nd component of the paradigm by which cells from early lesions can escape the fallopian tube and undergo future malignant transformation later, emerging suddenly as widespread malignancy. This dualistic model thus explains the paradox and opens new questions pertaining to the challenge of both early detection and prevention of this lethal malignancy.

Evaluation of the effects of a high-frequency acceleration (HFA) device on patient pain response to orthodontic forces. A multi-centered trial investigating pain sensitivity to orthodontic forces on 75 subjects at 4 study centers. Subjects underwent clear aligner treatment, with or without adjunctive HFA and documented their pain intensity using the validated NRS10 numeric rating scale. In-Office and At-Home ratings were measured separately for each subject for immediate and extended effect evaluations. Use of HFA devices in conjunction with clear aligner orthodontic treatment demonstrated significant reduction in subjects’ recorded pain ratings vs controls within 5 minutes of aligner exchange, (p = 0.006) and significant reduction in recorded pain ratings vs controls over a 7-day period following aligner exchange (p = 0.018). A 99.6% daily compliance rate with at home use of the HFA device was recorded for all subjects in the study. HFA significantly reduces pain attributed to orthodontic force. HFA delivers clinically significant immediate pain relief, and clinically significant extended pain relief over the 7 days following adjustment.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

We conducted an in-situ crystal structure analysis of ferroselite at non-ambient conditions. The aim is to provide a solid ground to further the understanding of the properties of this material in a broad range of conditions. Ferroselite, marcasite-type FeSe2, was studied under high pressures up to 46 GPa and low temperatures, down to 50 K using single-crystal microdiffraction techniques. High pressure and low temperatures were generated using a diamond anvil cell and a cryostat. We found no evidences of structural instability in the explored P-T space. The deformation of the orthorhombic lattice is slightly anisotropic. As expected, the compressibility of the Se-Se dumbbell, the longer bond in the structure, is larger than that of the Fe-Se bonds. Less obvious is the behavior of the octahedral bonds, the shorter bond is the most compressible determining a small increase in the octahedron distortion with pressure. We also achieved a robust structural analysis of ferroselite at low temperature in the diamond anvil cell. Structural changes upon temperature decrease are small but qualitatively similar to those produced by pressure.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

Our decisions today are part of an economic thinking which aims to fix problems and increase the efficiency of capital markets. Our economy is still largely approached as a system which is unre-lated to our environment or social returns like community well-being, social cohesion, equitable distribution of resources, etc. To fully incorporate sustainability into cost-benefit analysis, busi-nesses need to change their financial approach, showcasing how long-term thinking impacts prof-its. Money's value is not static and evolves with time and technology. We propose to introduce a variation of cost/benefit and present value calculations. Precise calculations reveal the benefits of long-term strategies over short-term profit focus. As financial systems evolve and technology advances, the accurate calculation of money's time value will continue to play a crucial role in shaping economic landscapes and guiding financial choices. In this article, we demonstrate that updated calculations could be a key enabler to visualize the benefits of long-term thinking or “patient finance” as compared to a short-term focus on profit. We introduce the concept and calculation of a Present Future Value (PFV).

Property valuation services using artificial intelligence (AI) have been developed, with more than 20 services available in Japan. However, since their algorithms and training data are not publicly available, the extent of differences in the AI property valuations among these services is not clear. This study focuses on the five services handling a lot of properties and uses a sample of 4,295 property valuations for 859 condominium units in six popular residential areas in Tokyo. (1) Multiple comparison tests of the AI property valuations among each service are conducted to confirm their statistical significance and to examine the degree of the difference and variation. (2) The business models of each service are compared to examine the factors contributing to these differences and variations. The results showed that there was a variation of approximately 0.15 in the coefficient of variation between the high and low valuation groups, and the service providers in the high valuation group guided the users to their sales, while those in the low valuation group focused on attracting users as their business models. The contribution of this study is to indicate the possibility that the business models may lead to the differences in the AI property valuations.

The revolutionary idea of complementary intelligence involves a unique strategy in which artificial intelligence (AI) works with human cognitive abilities embodied by natural intelligence (NI), creating a harmonious partnership instead of engaging in a competitive relationship. This innovative concept can potentially revolutionize how we approach scientific research and discovery. This cutting-edge process capitalizes on pooling the vast information from various distinct and autonomous sources to generate forecasts that frequently outshine human perspectives by significant margins, leading to groundbreaking advancements in scientific development based on hybrid intelligence. Multilayer networks extend traditional network theory to adjacent layers linked through copula nodes. Artificial intelligence, with its retrieval capacity to collect and interpret big data, sharply increases the number of nodes and their linking interpretation. This process, amplified by multilayer networks, dramatically improves the scalability of the networked ecosystem. Multilayer networks can represent NI and AI in complementary hyperplanes, connecting them with copula nodes and edge properties. Thus, it is possible to measure the interaction of NI and AI, assessing their scalable value co-creation properties. This study examines the interaction of NI and AI with an innovative and multidisciplinary approach. A theoretical framework of these related concepts precedes practical insights for possible applications in future research.

Frailty is a common condition in older adults that negatively impacts health and quality of life. This study evaluated a comprehensive, personalized, and coordinated intervention under the Value-Based Care approach to address frailty's multidimensional nature in older people. It em-ployed a pre-post randomized controlled design, involving frail individuals over 65 years in Valencia, Spain. Assessments were conducted at baseline, 12 months (immediately post-intervention), and 18 months. The intervention included a personalized care plan supported by technology, with monthly motivational follow-ups and plan updates by health professionals and participants. Outcomes were measured using an assessment questionnaire that included the International Consortium for Health Outcomes Measurement dataset for the older population: physical health, physical functioning, general mental health, satisfaction with social activities and relationships, ability to carry out usual social roles and activities, pain, general quality of life, loneliness, physical frailty, psychological frailty and social frailty. The study found signifi-cant improvements in physical frailty, quality of life, reduced health resource use and hospitali-zations, and lower levels of pain and depression/anxiety compared to baseline. The findings suggest further research into value-based care approaches, emphasizing the development and activation of personalized, comprehensive programs for older individuals with frailty.

The aim of this study was to develop a ready-to-eat vegetable-herb mixes with high nutritional and sensory values, as well as good storability. In this regard the suitability of fresh herbs (peppermint, oregano, green basil, red basil, and parsley) was tested for use in mixes with fresh-cut iceberg lettuce. Lettuce-herb mixtures were stored for 6 days at 5°C. The reason for the decrease in the appearance of the salads was the browning of the cut surface of the lettuce, as well as discoloration on the cut herbs. Comparing the storage ability of cut herbs, red basil and parsley retained the best appearance for 6 d at 5 °C. A small addition of herbs to fresh-cut iceberg lettuce caused a significant increase in contents of pro-health ingredients in the mixes. There were large discrepancies in the sensory quality of the mixes, but the highest quality and consumer acceptance were found for salads with parsley (5% and 10%) and red basil (5%). After harvest, the fresh herbs were more contaminated by molds than the iceberg lettuce. Bacterial, yeast and mold contamination increased during storage, but the rate of mold growth was much lower in the mixes with parsley compared to lettuce alone.

Convolutional Neural Networks (CNNs) are often criticized for their lack of transparency, acting as 'black boxes' in decision-making, a challenge compounded by class imbalance in ECG datasets, which limits their clinical application. This study introduces a CNN-based ECG signal classification model that enhances interpretability and addresses class imbalance through the Synthetic Minority Over-sampling Technique (SMOTE). The model also integrates Uniform Manifold Approximation and Projection (UMAP) for dimensionality reduction and SHAP value analysis, facilitating the visualization of decision boundaries and the assessment of feature contributions. Our evaluation using the MIT-BIH Arrhythmia Database highlights the model's high performance, with accuracy and precision nearing 1.00 for Normal ECG (NOR), Left Bundle Branch Block (LBBB), Right Bundle Branch Block (RBBB), and Ventricular Premature Beat (PVC) in the six-class task. In the ten-class task, the model demonstrated robustness, particularly with an accuracy of 0.9846, precision of 0.9783, recall of 0.9736, and F1 score of 0.9760 in Pacemaker Fusion Beat (PFHB), supported by an AUC of 0.9999 and AP of 0.9885. These results underscore the model's efficacy in cardiac rhythm recognition and resilience to class imbalance. Future research will explore sophisticated model architectures and feature extraction methods to enhance the model's generalization and clinical applicability for early heart disease diagnosis and personalized treatment.

This study aims to analyze various types of pellet fuels used as energy sources in Bulgaria, focusing on their energy characteristics and the consumer preferences. Both standard and specialized methods such as thermogravimetry (TG) and differential scanning calorimetry (DSC) are used for the analyses. The results from TG and DSC indicate that during the drying of the samples, moisture is evaporated from their surface, along with the release of volatile substances. The processes during the analysis are accompanied by energy absorption, with the main stage being combustion, where the primary amount of heat is generated. Standard analysis methods show that wood pellets usually contain about 7.31% moisture, 0.72% ash and have a calorific value of 18.33 kJ/kg, while sunflower pellets contain about 7.62% moisture, 2.42% ash and have a calorific value of 19.63 kJ/kg. Mixed pellets contain about 7.07% moisture, up to 0.69% ash and have a calorific value of 18.05 kJ/kg. A specialized marketing research was conducted to investigate consumer attitudes and preferences toward purchasing different types of solid biomass fuels on Bulgarian market. This study provides information on the quality of pellets as fuel by offering a detailed analysis of their fuel properties and ensuring their effective utilization as an energy source.

This study explores the current landscape of social value (SV) research in the construction industry, analyzing global trends and identifying future research directions. Using bibliometric analysis, research published in Elsevier Scopus database from 2013 to 2023 was extracted using the keywords "social value" AND "construction industry." Results indicate a focus on social value indicators, socioeconomic impacts, project management, innovative practices, and cross-sector collaborations. The study also reveals a lack of attention to SV in African countries' construction sectors. By highlighting research areas and identifying gaps, this study contributes to academic literature, suggesting the need for guidelines, particularly in developing countries, and advocating for further research on SV in the built environment and strategies for global social value creation.

This review article aims to delve into several aspects of sweetpotatoes and their leaves, including their nutritional composition, health benefits, culinary uses, and potential future implications as a superfood. It suggests an in-depth exploration of sweet potatoes' history, status, and prospects, highlighting their significance and potential economic value. Sweetpotatoes, often referred to as a powerhouse of nutrients, have gained popularity recently due to their remarkable nutritional composition and versatile culinary uses. This starchy root vegetable comes from the Convolvulaceae family and is consumed worldwide, playing a significant role in diverse cultures and cuisines. Besides their vibrant colors ranging from orange to purple, sweetpotatoes offer many health benefits, making them an essential addition to a well-balanced diet. Its extraordinary nutritional profile and numerous health benefits make it a superfood. Incorporating it into the diet can improve digestion, strengthen immunity, and reduce the risk of chronic diseases. With their versatility in the kitchen, there is no deficiency of charming and healthy recipes to explore. So, make room for sweet potatoes on your plate and unlock their vast potential to enhance your overall health and well-being. Overall, the future of sweetpotatoes looks bright as research and innovation aim to improve their nutritional value, adapt them to changing climate conditions, develop new varieties and products, and promote sustainable production practices. These developments can contribute to food security, economic growth, and healthier diets. Future research should focus on nutritional composition, health benefits, sustainable farming practices, cultivar development, and industrial applications to ensure sustainable and efficient production. By prioritizing research in these areas, we can enhance the utilization of sweet potatoes in various fields and secure their future for the next century.

There is less attention to use an environmental perspective in economic valuation and individuals' willingness to pay for recreational sites. Therefore, the aim of this study is to use contingent valuation methods to estimate the recreational value and willingness to pay of visitors to the protected area of Helen forest, considering the scale of the new environmental paradigm (NEP). To achieve this, the sample size for survey was determined using the Cochran method, and then economic valuation and environmental perspective questions were designed and completed through the completion of a dual-dimensional questionnaire and NEP scale. To determine the factors influencing individuals' willingness to pay, the logistic regression model was employed. In this study, two modeling approaches were used. The first utilized a base model containing socio-economic variables, while the second model integrated a NEP into the base, and subsequent estimations were conducted. The results indicated that 83.04% of visitors are willing to pay an amount for the recreational use of the study area. The estimated model results demonstrated that variables such as the proposed amount, frequency of visits, environmental statement, age, gender, education, individual monthly income, residency, and the NEP are among the most influential factors affecting the likelihood of accepting the proposed amount by tourists. The strong and positive correlation between the NEP and willingness to pay indicates that individuals with a favorable environmental perspective tend to exhibit a higher willingness to pay. In this study, the average willingness to pay per household per visit was 199,793 Rials, and the annual recreational value for the entire Helen forest area was 23746832564 Rials. Furthermore, the survey results regarding visitors' perspective on the NEP revealed that the average NEP score for visitors to Helen forest was 36.57, with the statement 'plants and animals have similar rights to humans' receiving the highest average score of 28.4. The result of this study shows the importance of environmental perspective for sustainable management of a recreational site to balance economic development with environmental conservation and social well-being.

In this short communication, following a brief introduction, we undertake a comprehensive analytical study of the weighted Simpson index. Our primary emphasis concerns the precise determination of the optimal point (minimizer) coordinates and of the minimum value of the index, a differentiable convex function, which is related to the harmonic mean concept. Furthermore, we address and solve the inversion problem and show the tight connection between both approaches. Last, we give some insights and final remarks on this subject.

Infertility affects millions worldwide, posing a significant global health challenge. The proteomic analysis of follicular fluid provides a comprehensive view of the complex molecular landscape within ovarian follicles, offering valuable information on the factors influencing oocyte development and on the overall reproductive health. The follicular fluid is derived from the plasma and contains various proteins that can have different roles in oocyte health and infertility and this fluid is a critical microenvironment for the developing oocytes as well. Using HPLC/MS method we investigated the protein composition of the follicular fluid and after classification we did relative quantification of the identified proteins in the pregnant (P) and non-pregnant (NP) groups. Based on the protein-protein interaction analysis ALB and ApoA1 was found to be hub proteins and the quantitative comparison of the P and NP groups resulted significantly lower concentration of ApoA1 and HDL-cholesterol in the P group. As both molecules are involved in the cholesterol transport, we also investigated their role in the development of oocytes and in the prediction of fertility.

As governments in various countries and regions issue tourism-friendly policies in the post-pandemic period, the voices for tourism consumption recovery and innovative transformation have attracted great attention. Many scholars, experts and industry professionals in the field of festivals are actively exploring efficient solutions for festival marketing and sustainability. It is worth rethinking tourists’ consumption psychology and perceived image toward exiting festival products as well as the antecedents that affect festival loyalty. The Qingdao International Beer Festival, as one of the most influential festivals in China, was selected as the research case for this study. The main goal of this study was to investigate festival consumption promotion mechanism by proposing a conceptual framework in which the associations from destination familiarity and product familiarity to loyal intentions (re-patronage and recommendation) were examined, with mediators of overall festival image, perceived value and overall satisfaction. Furthermore, the moderating role of visitor involvement in the proposed framework was also adequately demonstrated. The research findings are expected to provide a significant reference for the recovery and competitiveness improvement of the entire festival industry.

(1) Background: The definition of value addition is based on the process or processes which are used to transform physically the initial raw material in the final food or non-food article. Diversification can enhance the possibility of increased gains. The aim of this work is to give a reliable description of value addition when speaking of coconut-based beverages among all possible derivatives; (2) Methods: a systematic review of main papers on the argument has been critically examined and discussed; (3) Results: Processing degree is a consequence of consumers’ requests. Three different drivers for value addition have been considered: packaging, durability, and size options; sensorial features; and sustainability. Results of this investigation have highlighted the added value of several products because of recyclable packaging materials, intermediate or long durability expectations, different available sizes, and good or excellent sensorial performances; (4) Conclusions: There are different value-added coconut-based beverages with interesting perspectives. On the other side, sustainability and eco-friendly policies may be a problem for those products which are produced similarly to non-coconut based beverages. The opportunity of certified organic and/or fair-trade products could help the industry of coconuts in the next future. More research is still needed in this ambit.