The solar energy can mitigate the power supply shortage in remote regions for portable irrigation systems. The accurate prediction of solar irradiance is crucial for determining the quantity of solar panels and the power capacity of photovoltaic power generation (PVPG) systems for mobile sprinkler machines. In this study, a prediction method is proposed to forecast the solar irradiance of typical irrigation areas. The impact of the meteorological parameters on the solar irradiance is studied, and four different parameter combinations are formed and considered as input to the prediction model. Based on meteorological data provided by ten typical radiation stations uniformly distributed nationwide, an Extreme Gradient Boosting (XGBoost) model optimized using the Whale Optimization Algorithm (WOA) is developed to predict the solar radiation. The prediction accuracy and stability of the proposed method are then evaluated for different input parameters through training and testing. The differences between the prediction performances of models trained based on single-station data and mixed data from multiple stations are also compared. The obtained results show that the proposed model achieves the highest prediction accuracy when the maximum temperature, minimum temperature, sunshine hours ratio, relative humidity, wind speed, and extraterrestrial radiation are used as the input parameters. The prediction effectiveness is also verified based on measured data. The WOA-XGBoost model has higher prediction accuracy than the XGBoost model, with predicted values falling within acceptable ranges. The model developed using mixed data of multiple stations can be applied for forecasting solar irradiance in different regions. This study provides a foundation for the optimization of the configuration of PVPG systems for mobile sprinkler machines.

A two-qubit Hamiltonian model exhibiting an SU(2) symmetry is considered. The related dynamical problem results to be then exactly solvable both in the time-independent and in the time-dependent case. Basing on the formal, general form of the related time evolution operator, the time-dependence of the level of entanglement of some initial conditions is studied within both the Rabi and the Landau-Majorana-Stückelber-Zener scenarios.

Ensuring precise segmentation of colorectal polyps holds critical importance in the early diagnosis and treatment of colorectal cancer. Nevertheless, existing deep learning-based segmentation methods are fully-supervised, requiring extensive precise manual pixel-level annotation data, which leads to high annotation costs. Additionally, it remains challenging to train large-scale segmentation models when confronted with limited colonoscopy data. To address these issues, we introduce the general segmentation foundation model—Segment Anything Model (SAM) into the field of medical image segmentation. Fine-tuning the foundation model is an effective approach to tackle sample scarcity. However, current SAM fine-tuning techniques still rely on precise annotations. To overcome this limitation, we propose WSPoly-SAM, a novel weakly-supervised approach for colonoscopy polyp segmentation. WSPoly-SAM utilizes weak annotations to guide SAM in generating segmentation masks, which are then treated as pseudo-labels to guide the fine-tuning of SAM, thereby reducing the dependence on precise annotations data. To improve the reliability and accuracy of pseudo-labels, we have designed a series of enhancement strategies to improve the quality of pseudo-labels and mitigate the negative impact of low-quality pseudo-labels. Experimental results on five medical image datasets demonstrate that WSPoly-SAM outperforms current fully-supervised mainstream polyp segmentation networks on the Kvasir-SEG, ColonDB, CVC-300, and ETIS datasets. Furthermore, by using different amounts of training data in weakly-supervised and fully-supervised experiments, it is found that weakly-supervised fine-tuning can save 70% to 73% of annotation time costs compared to fully-supervised fine-tuning. This study provides a new perspective on the combination of weakly-supervised learning and SAM models, significantly reducing annotation time and offering insights for further development in the field of colonoscopy polyp segmentation.

There are important challenges for modeling large electrical distribution circuits, even more with the presence of distributed renewable generation. Constructing simulations for assessing the effect of the penetration of distributed generation on electrical distribution networks has become of great importance for Distribution Network Operators (DNOs). This paper proposes a simulation strategy based on open-source platforms and the integration of scripting tools for the rapid modeling of large-scale electrical distribution circuits with distributed renewable generation. The implementation is based on the adaptation of a tool called QGIS2OpenDSS, which creates OpenDSS distribution network models directly from an open-source geographic information system, QGIS. The plugin’s capabilities are demonstrated using a real distribution feeder with more than 60% penetration of renewable generation based on photovoltaic systems. These simulations are carried out using real data from a circuit provided by a DNO in the Dominican Republic, which is used to demonstrate how this approach provides a more accessible and flexible way to simulate and assess the effect of Distributed Energy Resources (DERs) in Medium Voltage (MV) and Low Voltage (LV) networks, enabling utilities to evaluate system performance and identify potential issues.

Natural products contribute substantially to anticancer therapy; the plant kingdom provides an important source of molecules. Conofolidine is a novel Aspidosperma-Aspidosperma bisindole alkaloid isolated from the Malayan plant Tabernaemontana corymbosa. Herein, we report conofolidine’s anticancer activity together with that of three other bisindoles - conophylline, leucophyllidine and bipleiophylline against human-derived carcinoma cell lines. Remarkably, conofolidine was able to induce apoptosis (as observed in MDA-MB-468 breast cancer cells) or senescence (as detected in HT-29 colorectal carcinoma cells). Annexin V-FITC/PI, caspase activation and PARP cleavage confirmed the former while positive β-gal staining corroborated the latter. Evident cell cycle perturbations were observed comprising S-phase depletion, accompanied by downregulated CDK2, and cyclins (A2, D1) with p21 upregulation. Confocal imaging of HCT-116 cells revealed induction of aberrant mitotic phenotypes - multi-nucleation, membrane blebbing and DNA-fragmentation. The DNA integrity assessment of HCT-116 and MDA-MB-468 showed irreparable damage identified by increased fluorescent γ-H2AX during the G1 cell cycle phase. Furthermore, γ-H2AX foci were visually validated in HCT-116 and MDA-MB-468 cells using confocal microscopy. Conofolidine increased oxidative stress, preceding apoptosis- and senescence-induction in most carcinoma cell lines as seen by enhanced ROS levels accompanied by NQO1 expression. Collectively, we present conofolidine as a potential anticancer candidate capable of inducing heterogeneous modes of cancer cell death in vitro, encouraging further preclinical evaluation of this natural product.

Industrial Control Systems (ICS) are integral to managing and optimizing processes in various industries, including manufacturing, power generation, and more. However, the scarcity of widely adopted ICS datasets hampers research efforts in areas like optimization and security. This scarcity arises due to the substantial cost and technical expertise required to create physical ICS environments. In response to these challenges, this paper presents a groundbreaking approach to generating synthetic ICS data through a data-driven ICS network simulation. We circumvent the need for expensive hardware by recreating the entire ICS environment in software. Moreover, rather than manually replicating the control logic of ICS components, we leverage existing data to autonomously generate control logic. The core of our method involves the stochastic setting of setpoints, which introduces randomness into the generated data. Setpoints serve as target values for controlling the operation of the ICS process. This approach enables us to augment existing ICS datasets and cater to the data requirements of machine learning-based ICS intrusion detection systems and other data-driven applications. Our simulated ICS environment employs virtualized containers to mimic the behavior of real-world PLCs and SCADA systems, while control logic is deduced from publicly available ICS datasets. Setpoints are generated probabilistically to ensure data diversity. Experimental results validate the fidelity of our synthetic data, emphasizing its ability to closely replicate temporal and statistical characteristics of real-world ICS networks. In conclusion, this innovative data-driven ICS network simulation offers a cost-effective and scalable solution for generating synthetic ICS data. It empowers researchers in the field of ICS optimization and security with diverse, realistic datasets, furthering advancements in this critical domain. Future work may involve refining the simulation model and exploring additional applications for synthetic ICS data.

In this paper, we propose a method for the generation of simulation test scenarios for autonomous driving. Based on the requirements of standard regulatory test scenarios, we can generate virtual simulation scenarios and functional scenario libraries for autonomous driving, which can be used for simulation verification of different ADAS functions. Firstly, the design operation domain (ODD) of the functional scenario is selected and the weight values of the ODD elements taken are calculated; then a combination test algorithm based on parameter weights is improved to generate autonomous driving virtual simulation test cases for the ODD elements, which can effectively reduce the number of generated test cases compared with the traditional combination test algorithm; then the traffic participant elements under each test case are Then, the values of the subelements under the traffic participant element in each test case are sampled and clustered to obtain hazard specific scenarios. Finally, the specific scenarios are applied to the automatic emergency braking (AEB) system on the model-in-the-loop (MIL) testbed to verify the effectiveness of this scenario generation method.

A novel approach was developed that combined LP-based row generation with optimization-based sorting to tackle computational challenges posed by budget allocation problems with combinatorial constraints. The proposed approach dynamically generated constraints using row generation and prioritized them using optimization-based sorting to ensure a high-quality solution. Computational experiments and case studies revealed that as the problem size increased, the proposed approach outperformed simplex solutions in terms of solution search time. Specifically, for a problem with 50 projects (N = 50) and 2,251,799,813,685,250 constraints, the proposed approach found a solution in just 1.4 seconds, while LP failed due to the problem size. The proposed approach demonstrated enhanced computational efficiency and solution quality compared to traditional LP methods.

The optimal regime of three-photon resonant excitation of a helium atom by a femtosecond ul-traviolet (UV) pulse was discovered and numerically studied, at which the maximum power of the third harmonic of the UV field is achieved in the spectrum of dipole acceleration (the second time derivative of the induced dipole moment) of the atom. It is shown that the optimal frequency of the UV field nearly coincides with the frequency of the three-photon transition 1s2 – 1s2p, taking into account its shift as a result of the dynamic Stark effect, and the intensity of the UV field is dictated by the condition of maximizing the product of the populations of the 1s2 and 1s2p states, averaged over the time interval during which the UV field is non-zero. For the considered UV field durations, from 10 to 100 cycles of the carrier frequency (from units to tens of femtoseconds), the optimal intensity lies in the range from 10^14 W/cm^2 to several units of 10^14 W/cm^2. It is shown that with an optimal choice of the frequency and intensity of the UV field, the dynamics of excitation of bound and continuum states, as well as the shape of the time envelope of the dipole acceleration of the atom, weakly depend on the duration of the UV field envelope; only their time scale changes significantly. In addition, under the optimal conditions the average power of the third harmonic signal in the dipole acceleration spectrum is practically independent of the duration of the UV field envelope.

We present results of the detected voltage distribution of a quantum random number generator based on the photonic integration of semiconductor laser, delay interferometer and photodetector. We find that the integrated system behaves as expected for random number generation from gain-switched laser sources. The biggest advantage is that only electrical connections are needed to operate the system without the need for tricky and expensive optical alignment to external circuitry. We supply results showing that random bit stream created from the random numbers passes the NISTS statistical test suite tests; thus demonstrating the feasibility to generate random number via quantum means at gigabit/s rates from a single photonic integrated circuit. The results are backed by numerical simulations.

This study presents a comprehensive investigation of entropy generation during natural convection in a porous medium with Casson fluid. The governing equations, including the momentum, energy, and entropy balance equations, are solved numerically using finite element method. Through the analysis, various parameters affecting entropy generation are investigated, such as the Casson fluid parameter, Radiation, Prandtl number, and Rayleigh number. The results indicate that the Casson fluid parameter significantly influences the flow and heat transfer characteristics, while the Darcy number and Rayleigh number control the intensity of natural convection. Moreover, the Prandtl number determines the relative significance of heat transfer compared to viscous effects.

- Power grids of the future will likely incorporate more renewable energy distributed generation (REDG), also known as alternative energy systems. REDG units are increasingly being used in electrical transmission networks because to the overall positive effects they have on power networks. REDG systems are the backbone of smart electric networks and are essential to the operation of the smart grid. These REDG systems can additionally improve system reliability by providing some customers with a backup generator in the event of power interruptions. The report offers a thorough evaluation of the existing body of information on the topic of electric vehicles' (EVs') future interactions with the smart grid. The combination of the EVs' potential deployment and the smart grid's conceptual goal presents challenges in electric grid infra-structure, communication, and control. The proposal for connecting EVs to the grid is based on research into cutting-edge smart metering and communication systems. In the context of the vehicle-to-grid (V2G) phenomenon, the possibilities, benefits, and limitations of various EV smart charging systems are also fully examined. There is a fast growing percentage of distributed energy that is wind and solar photovoltaic. Their variable power output, however, introduces fresh challenges for those responsible for organizing, operating, and controlling the power grid. While fluctuations in the electric grid are problematic, they may be mitigated by the entry of EVs into the energy market. As such, we do a comprehensive literature search to learn more about the exciting research gap that needs to be filled and the most recent possible answer that involves EVs. Additionally, we take a close look at the practicality of the sophisticated V2G technology. The smart grid is a developing concept for the world's energy infrastructure, and this study analyzes in depth how EVs interact with it.

Nowadays, energy decarbonization due to the integration of renewable energy sources presents important challenges to overcome. The intermittent nature of photovoltaic systems reduces power quality by producing voltage variations and frequency deviations in electrical systems networks, especially, in weak and isolated distribution systems in developing countries. This paper presents a power smoothing method improving the low pass filter and moving average for grid-connected photovoltaic system, the novel method includes state-of-charge monitoring control of the supercapacitors energy storage system to reduce the fluctuations of photovoltaic power at the point of common coupling. A case study for a microgrid in a high-altitude city in Ecuador is presented with exhaustive laboratory tests using real data. The ultimate goal of this research is to improve energy power quality in electrical distribution systems to cope with the growth of renewable penetration.

The battery energy storage systems (BESS) are most promising solution for increasing efficiency and flexibility of distribution networks (DNs) with significant penetration level of photovoltaic (PV) systems. There are various issues related to the optimal operation of DNs with integrated PV sys-tems and BESS that need to be addressed to maximize DN performance. This paper deals with the day-ahead optimal active-reactive power dispatching in unbalanced DNs with integrated sin-gle-phase PV generation and BESSs. The objectives are the minimization of cost for electricity, en-ergy losses in the DN and voltage unbalance at three-phase load buses by optimal managing of active and reactive power flows. To solve this highly constrained nonlinear optimization problem, a hybrid particle swarm optimization with sigmoid-based acceleration coefficients (PSOS) and cha-otic gravitational search algorithm (CGSA), called PSOS-CGSA algorithm, is proposed. A scenario based approach encompassing the Monte Carlo simulation (MCS) method with the simultaneous backward reduction algorithm is used for the probabilistic assessment of the uncertainty of PV generation and power of loads. The effectiveness of the proposed procedure is evaluated through the series test cases in a modified IEEE 13-bus feeder.

“A Picture is worth a thousand words”. Given an image, humans are able to deduce various cause-and-effect captions of past, current, and future events beyond the image. The task of visual commonsense generation aims at generating three cause-and-effect captions (1) what needed to happen before, (2) what is the current intent, and (3) what will happen after for a given image. However, such a task is challenging for machines owing to two limitations: existing approaches (1) directly utilize conventional vision-language transformers to learn relationships between input modalities, and (2) ignore relations among target cause-and-effect captions but consider each caption independently. We propose Cause-and-Effect BART (CE-BART) which is based on (1) Structured Graph Reasoner that captures intra- and inter-modality relationships among visual and textual representations, and (2) Cause-and-Effect Generator that generates cause-and-effect captions by considering the causal relations among inferences. We demonstrate the validity of CE-BART on VisualCOMET and AVSD benchmarks. CE-BART achieves SOTA performances on both benchmarks, while extensive ablation study and qualitative analysis demonstrate the performance gain and improved interpretability.

Generation of unique identifiers extracted from the physical characteristics of the underlying hardware ensures the protection of electronic devices against counterfeiting and provides security to the data they store and process. This work describes the design of an efficient Physical Unclonable Function (PUF) based on the differences in the frequency of Ring Oscillators (ROs) with identical layout due to variations in technological processes involved in the manufacture of the integrated circuit. The logic resources available in the Xilinx Series-7 programmable devices are exploited in the design to make it more compact and achieve an optimal bit-per-area rate. On the other hand, the design parameters can also be adjusted to provide a high bit-per-time rate for a particular target device. The PUF has been encapsulated as a configurable Intellectual Property (IP) module, providing it with an AXI4-Lite interface to ease its incorporation into embedded systems in combination with soft- or hard-core implementations of general-purpose processors. The capability of the proposed RO-PUF to generate implementation-dependent identifiers has been extensively tested, using a series of metrics to evaluate its reliability and robustness for different configuration options. Finally, in order to demonstrate its utility to improve system security, the identifiers provided by RO-PUFs implemented on different devices have been used in a Helper Data Algorithm (HDA) to obfuscate and retrieve a secret key.

Ayurveda as a healthcare system has survived for thousands of years but continues to be dogged by reported lack of efficacy of the treatments in clinical trials. The reported lack of efficacy could be due to a real lack of efficacy (which then contradicts the survival of Ayurveda as a functional medical system enjoying considerable public patronage) or could be attributed to inadequacies in the efforts towards evidence generation or in a larger context the overall scientific conduct of research in Ayurveda. In an effort towards better evidence generation, there is an immediate need for standardizing the design, conduct and reporting of clinical trials of Ayurveda but it is a daunting task. For this effort to benefit the scientific endeavors of Ayurveda researchers, it should allow the researchers to be able to apply Ayurveda’s multi-component, individualized and inherently holistic approach. Statistical principles can benefit this effort. Statistical hypothesis testing (SHT) is central to these statistical principles and also aligns well with conventional scientific principles of evidence generation. Although there are challenges with SHT, good practitioners engaged in it do much more than just apply the mathematical theory behind it. As a particular example, lot of time in clinical trial designing is spent in addressing biases and designing trials prudently by minimizing the effect of such biases. SHT can benefit such an effort objectively. There is a need for Ayurveda researchers to engage deeply and mindfully about biases in study design in order to gain scientific validity and acceptability. The article highlights issues that arise in Ayurveda research, and discusses few ways of dealing with these issues using statistical principles.

Photovoltaic power generation has high variability and uncertainty because it is affected by uncertain factors such as weather conditions. Therefore, probabilistic forecasting is useful for optimal operation and risk hedging in power systems with large amounts of photovoltaic power generation. However, deterministic forecasting is the mainstay of photovoltaic generation forecasting; there are few studies on probabilistic forecasting and feature selection from weather or time-oriented features in such forecasting. In this study, prediction intervals were generated by the lower upper bound estimation using neural networks with two outputs to make probabilistic predictions. The objective was to improve prediction interval coverage probability (PICP), mean prediction interval width (MPIW), and loss, which is the integration of these two metrics, by removing unnecessary features through feature selection. When features with high gain were selected by random forests (RF), in the forecast of 14.7-kW PV systems, loss improved by 1.57 kW, PICP by 0.057, and MPIW by 0.12 kW on average over two weeks compared to the case where all features were used without feature selection. Therefore, the low gain features from RF act as noise in LUBE and reduce the prediction accuracy.

High molecular weight glutenin subunits (HMW-GS) and Low molecular weight glutenin subunits (LMW-GS) in mature grains play important roles in the formation of glutenin macropolymer and gluten quality. To characterize the expressed glutenin genes of the bread wheat variety Xinmai 26 during seed development, in this study, we measured the dough rheological properties of mature grains through farinograph and gluten testing system, and revealed its strong gluten quality. The compositions of HMW-GS and LMW-GS were analyzed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS). Further, a total of 18 full-length transcripts were obtained by third-generation RNA sequencing, including 5 transcripts of HMW-GS genes and 13 transcripts of LMW-GS genes (8 intact genes and 5 pseudogenes). The deduced protein structures of transcript sequences exhibit the typical HMW-GS and LMW-GS structural characteristics. Moreover, a specific functional marker was developed to make better use of the extra cysteine residue of 1Dx5 subunit. This study provides an efficient method to accurately identify glutenin genes in bread wheat through matching full-length transcripts to their spectrum of glutenin, which will be helpful to understand the contributions of glutenin genes to wheat quality.

The fifth Generation (5G) mobile networks use millimeter Waves (mmWaves) to offer giga bit data rates. However, unlike microwaves, mmWave links are prone to user and topographic dynamics. They easily get blocked and end up forming irregular cell patterns for 5G. This in turn cause too early, too late, or wrong handoffs (HOs). To mitigate HO challenges, sustain connectivity and avert unnecessary HO, we propose a HO scheme based on Jump Markov Linear System (JMLS) and Deep Reinforcement Learning (DRL). JMLS is widely known to account for abrupt changes in system dynamics. DRL likewise emerges as an artificial intelligence technique for learning highly dimensional and time-varying behaviors. We combine the two techniques to account for time-varying, abrupt, and irregular changes in mmWave link behaviour by predicting likely deterioration patterns of target links. The prediction is optimized by meta training techniques that also reduces training sample size. Thus, the JMLS-DRL platform formulates intelligent and versatile HO policies for 5G. Results show our proposed prediction scheme about target link behavior post HO to be highly reliable. The scheme also averts unnecessary HOs thus ably supports longer dew time.

This paper provides a methodology for the production of synthetic images for training neural networks to recognise shapes and objects. There are many scenarios in which it is difficult, expensive and even dangerous to produce a set of images that is satisfactory for the training of a neural network. The development of 3D modelling software has nowadays reached such a level of realism and ease of use that it seemed natural to explore this innovative path and to give an answer regarding the reliability of this method that bases the training of the neural network on synthetic images. The results obtained in the two proposed use cases, that of the recognition of a pictorial style and that of the recognition of migrants at sea, leads us to support the validity of the approach, provided that the work is conducted in a very scrupulous and rigorous manner, exploiting the full potential of the modelling software. The code produced, which automatically generates the transformations necessary for the data augmentation of each image, and the generation of random environmental conditions in the case of Blender and Unity3D software, is available under the GPL licence on GitHub. The results obtained lead us to affirm that through the good practices presented in the article, we have defined a simple, reliable, economic and safe method to feed the training phase of a neural network dedicated to the recognition of objects and features, to be applied to various contexts.

In this paper we propose the generation of synthetic small and more sophisticated molecule structures that optimize the binding affinity to a target (ASYNT-GAN). To achieve this we leverage on three important achievements in A.I.: Attention, Deep Learning on Graphs and Generative Adversarial Networks. Similar to text generation based on parts of text we are able to generate a molecule architecture based on an existing target. By adopting this approach, we propose a novel way of searching for existing compounds that are suitable candidates. Similar to question and answer Natural Language solutions we are able to find drugs with highest relevance to a target. We are able to identify substructures of the molecular structure that are the most suitable for binding. In addition, we are proposing a novel way of generating the molecule in 3D space in such a way that the binding is optimized. We show that we are able to generate compound structures and protein structures that are optimised for binding to a target.

The deregulated markets have replaced the traditional way of trading electricity from the producers to the consumer, via government-owned organizations and regulated tariffs. Nowadays, electricity prices are determined by the offer-demand mechanism and consumers can negotiate tariffs with their supplier of choice. For classic wholesale suppliers, the tariffs are a result of the transactions performed on the wholesale market and the energy mix available in certain geographical regions. In parallel with becoming eligible and participating in retail electricity markets, the consumers use increasingly local generation sources based mostly on renewable energy technologies such as PV panels, and become prosumers. They want to be able to sell back to the market the generation surplus, in order to obtain the maximum benefits from their initial investment. Currently, several trading mechanisms for prosumers are available, ranging from the simplest, selling back the surplus to an aggregator at fixed tariffs, to more complex market schemes. This paper proposed a two-tier local market model for prosumers and consumers connected in microgrids, based on the blockchain technologies and other technologies and concepts such as remote sensing, smart grids, crowdsourcing and energy poverty.

The deregulated markets have replaced the traditional way of trading electricity from the producers to the consumer, via government-owned organizations and regulated tariffs. Nowadays, electricity prices are determined by the offer-demand mechanism and consumers can negotiate tariffs with their supplier of choice. For classic wholesale suppliers, the tariffs are a result of the transactions performed on the wholesale market and the energy mix available in certain geographical regions. In parallel with becoming eligible and participating in retail electricity markets, the consumers use increasingly local generation sources based mostly on renewable energy technologies such as PV panels, and become prosumers. They want to be able to sell back to the market the generation surplus, in order to obtain the maximum benefits from their initial investment. Currently, several trading mechanisms for prosumers are available, ranging from the simplest, selling back the surplus to an aggregator at fixed tariffs, to more complex market schemes. This paper proposed a two-tier local market model for prosumers and consumers connected in microgrids, based on the blockchain technologies and other technologies and concepts such as remote sensing, smart grids, crowdsourcing and energy poverty.

Fossil fuels and carbon origin resources are affecting our environment. Therefore, alternative energy sources have to be established to co-produce energy along with fossil fuels and carbon origin resources until it is the right time to replace them. Microbial Fuel Cell (MFC) is a promising technology in the field of energy production. Compared to the conventional power sources it is more efficient and not controlled by the Carnot cycle. Its high efficiencies, low noise, and less pollutant output could make it revolutionize in the power generation industry with a shift from centrally located generating stations and long-distance transmission lines to dispersed power generation at load sites. In this review, several characteristics of the MFC technology will be highlighted. First, a brief history of abiotic to biological fuel cells and subsequently, microbial fuel cells is presented. Second, the focus is then shifted to elements responsible for the making MFC working with efficiency. Setup of the MFC system for every element and their assembly is then introduced, followed by an explanation of the working machinery principle. Finally, microbial fuel cell designs and types of main configurations used are presented along with scalability of the technology for the proper application.

Plasma being the fourth and most abundant form of matter extensively exists in the universe in the inter-galactic regions. It provides an electrically neutral medium of unbound negative and positive charged particles, which has been produced by subjecting air and various other gaseous mixtures to strengthen the electromagnetic field and by heating compressed air or inert gasses for creating negative and positive charged particles known as ions. Nowadays, many researchers are paying attention to the formation of artificial Plasma and its potential benefits for mankind. The literature is sparsely populated with the applications of Plasma. This paper presents specific methods of generation and applications of Plasma, which benefits humankind in various fields, such as in electrical, mechanical, chemical and medical fields. These applications include hydrogen production from alcohol, copper bonding, semiconductor processing, surface treatment, Plasma polymerization, coating, Plasma display panels, antenna beam forming, nanotechnology, Plasma Torch, Plasma pencils, low-current non-thermal Plasmatron, treatment of prostate cancer, Plasma source ion implantation, cutting by Plasma, Plasma etching, pollution control, neutralization of liquid radioactive waste, etc. Resultantly, worth of Plasma technology in the medical industry is increasing exponentially that is closing the gap between its benefits and cost of equipment used for generating and controlling it.

In this work we present the results obtained with an artificial neural network (ANN) which we trained to predict the expected output of high-order harmonic generation (HHG) process, while exploring a multi-dimensional parameter space. We argue on the utility and efficiency of the ANN model and demonstrate its ability to predict the outcome of HHG simulations. In this case study we present the results for a loose focusing HHG beamline, where the changing parameters are: the laser pulse energy, gas pressure, gas cell position relative to focus and gas cell length. The physical quantity which we predict here using ANN is directly related to the total harmonic yield in a specified spectral domain (20-40 eV). We discuss the versatility and adaptability of the presented method.

Agricultural product like cassava produces huge amounts of waste when processed to consumable goods. The waste generated is generally considered to contribute largely to environmental pollution. This study therefore investigates the waste management practice that is adopted by cassava processors in Ogun State, Nigeria. Five (5) Local Government Areas (LGAs) dominant in processing cassava were selected for the study on the basis of spatial location distribution; landmass and population. The survey involved the use of structured questionnaires administered to cassava processors of the selected LGAs. The Statistical Package for Social Sciences (SPSS) software application and descriptive statistics were used for data analysis. Results of the analysis show that majority (70%) of the cassava processors are females. Cassava peel constitutes 10% of the waste produced, of which 91% are heaped at refuse dump in most communities. Results also reveal that 86.3% of cassava residues are used for animal feeds. Other findings show that the peels when dried are used as bio-fuel for cooking and there is a significant potential for biogas production. From the data captured from respondent during the study, most processors are willing to pay for an improved waste management system. The study therefore suggests proper waste management of cassava waste to minimize environmental pollution.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

This paper proposes a novel approach called Multi-strategy Improved Chaotic Whale fused with Perturbation Observation method (IWOA-PO) for Maximum Power Point Tracking (MPPT) con-trol, to address the challenge of low efficiency in photovoltaic (PV) power generation under local shadows, according to the features of whale optimization algorithm (WOA) and perturbation observation (P&O) method. In the early stage of control algorithm, IWOA is used for global search to quickly locate the position of the Maximum Power Point (MPP). In the later stage of control algorithm, P&O is used for fine-grained local search to quickly, accurately and low oscillation track the position of the global maximum power point (GMPP). In order to verify the correctness, the tracking performance of IWOA-PO is comprehensively compared with WOA-PO、WOA、PSO under four conditions including uniform illumination, static partial shade, dynamic irradiance mutation and sudden changes in temperature and irradiance. In the above four conditions, the IWOA-PO algorithm has faster convergence and less power oscillations compared to the re-maining three algorithms, indicating that the IWOA-PO algorithm is effective. Finally, a physical verification experiment process is built to verify the correctness and effectiveness of the algorithm proposed in this paper.

A suitable waste management strategy is crucial for a sustainable and efficient circular economy in the construction sector, and requires precise data on the volume of demolition waste (DW) gen-erated. Therefore, we developed an optimal machine learning (ML) model to forecast the quantity of recycling and landfill waste based on the characteristics of DW. A dataset comprising infor-mation on the characteristics of 150 buildings, demolition equipment utilized, and volume of five waste types generated (i.e., recyclable mineral, recyclable combustible, landfill specified, and landfill mix waste, and recyclable minerals) was constructed. ML models were developed to predict the quantities of such waste. Artificial neural network, decision tree, gradient boosting machine, k-nearest neighbors, linear regression, random forest (RF), and support vector regression were applied, and optimal models were derived via hyperparameter tuning. The RF model demonstrated superior performance. In both validation and test phases, the “recyclable mineral waste” and “recyclable combustible waste” models achieved accuracies of of 0.987 and 0.972, re-spectively. The “recyclable metals” and “landfill specified waste” models achieved accuracies of 0.953 and 0.858 or higher, respectively. Moreover, the “landfill mix waste” model exhibited an accuracy of 0.984 or higher. SHapley Additive exPlanations analysis highlighted floor area as the primary input variable influencing model performance. The type of equipment employed in demolition emerged as another crucial input variable impacting the volume of recycling and landfill wastes generated. The developed model can provide precise data on waste management, thereby facilitating the decision-making process for industry professionals.

The paper is concerned with the concept of elementary observations (EO). EOs are experimental answers to the question whether a matter-instrument interaction had taken place at the micro-scale of quantum phenomena. Focusing on the specific case of photon detection, we show that during their lifetimes EOs proceed through the four phases of initiation, detection, erasure and reset. Once generated, the observational value of EOs can be measured in units of the Planck quantum of physical action h=4.136×10^(-15) eVs. Once terminated, each unit of entropy of size k_B=8.617×10^(-5) eV⁄K, which had been created in the instrument during the observational phase, needs to be removed from the instrument to ready it for a new round of photon detection. This withdrawal of entropy takes place at an energetic cost of at least two units of the Landauer minimum energy bound of E_La=ln⁡〖(2) k_B T_D 〗 for each unit of entropy of size k_B.

Visualising textual content could be helpful to professionals as well as amateurs across several fields. However, training a text-to-image generator in the mainstream domain requires large amounts of paired text-image and data, which is too expensive to collect since labeling millions of images and videos can be tiresome. GANs like StackGAN and StyleGAN can be considered as solutions to generate images from text. But the images generated may be of low accuracy and resolution, and the entire processing can be highly time-consuming. Moreover, image generation is a notion that is still being researched. Hence, the process of developing a Video Generation model necessitates substantial research. Despite the need for such a model, modern technology has lagged behind the solutions to this problem. This proposal suggests combining two methods, Text modification for Action Definition (TexAD) and SeQuential Image Generation for Video Synthesis (SQIGen). The proposed solution synthesises a sequence of images from textual information feeds and combines these images to create a video. TexAD uses Natural Language Processing and Deep Learning techniques to process, classify and modify text data. SQIGen is an extension of the VQGAN+CLIP neural network architecture that generates a sequence of images from the modified text data

The global increase in population, the phenomenon of climate change, the issue of water pollution and contamination, and the inadequate management of water resources all exert heightened strain on freshwater reserves. The potential utilization of the interfacial solar steam generation (ISSG) system, which utilizes photothermal conversion to generate heat on material surfaces for wastewater purification and desalination purposes, has been successfully demonstrated. Textile materials based ISSG devices, including (woven, nonwoven and knitting) fabrics and electrospinning membranes, exhibit distinct properties such as rough surface texture, high porosity, significant surface area, exceptional flexibility, and robust mechanical strength. These characteristics, combined with their affordability, accessibility, and economic viability for widespread implementation, make them extremely attractive for applications in SSG. In this review, a comprehensive analysis of emerging concepts, advancements and applications of textile materials (woven, nonwoven, and knitting) fabrics and electro-spun membranes in the ISSG for wastewater purification and desalination is highlighted. We also emphasize significant obstacles and potential prospects in both theoretical investigations and real-world implementations, aiming to contribute to future advancements in the domain of textile based materials interfacial evaporation in wastewater purification and desalination. Furthermore, the drawbacks and the challenges of ISSG systems are also highlighted.

It is argued that all physical knowledge ultimately stems from observation and that the simplest possible observation is that an event has happened at a certain space-time location . Considering historic experiments, which had been groundbreaking in the evolution of our modern ideas of matter on the atomic, nuclear and elementary particle scales, it is shown that such experiments produce as outputs macroscopically observable events which represent binary decisions with regard to simple alternatives and which accumulate in the course of time into spatio-temporal patterns whose forms allow decisions to be taken concerning conceivable alternatives of explanation. Working towards elucidating the physical and information-theoretic characteristics of those elementary pieces of information we arrive at the conclusion that - unlike the events of relativity which are mere 4-tuples of spacetime coordinates - the events of observation are pieces of information endowed with the properties of physical action, spacetime extension, and Lorentz invariance. Another important aspect is that such events are produced at the expense of irreversibly dissipating energy which can be stated in Landauer diction in the form that more energy needs to be spent in the erasure of events than had previously been invested in their initiation.

To protect power lines, distance relays are used which can rely on a modified distance resistance. But usually the operating range of these relays changes as the network conditions change (network topology, load value, output value, etc.) and leads to false trips, By using methods that can process information and recognize patterns, for example, the use of micro and intelligent processor algorithms can use the new relays with high precision and thus provide adequate protection. In this study, a distance relay was modeled using a neural network, and it was observed that the neural relay had higher accuracy than the conventional relay. In addition to detecting the fault and its location, type and phase of the fault, three-stage simultaneous protection can be performed. As a result, the number of linear relays can be reduced by using relays based on neural technologies. An MLP (multilayer perceptron) neural network is used to model a sequence of distances.

Soiling accumulated on a photovoltaic (PV) module can significantly reduce the transmittance of the cover glass, resulting in power losses and consequent economic losses. Natural atmospheric parameters influence the accumulation of soiling at the various geographic locations. In this paper, the approaches and outcomes of the research studies on either indoor (simulator-based) or outdoor (field-based) PV soiling have been thoroughly reviewed. Different parameters depicted for the power loss of PV modules are analyzed individually and presented. Moreover, this study delves into a detailed examination of the key factors influencing dust depositions on PV modules in various geographical regions, with a particular focus on their relationship with climatic conditions. This way, probable future research directions to quantify soiling losses are identified. In addition, different loss prevention and mitigation techniques are also reviewed. This makes it possible to highlight effective strategies and pinpoint potential future research lines in these areas.

In recent years, the genesis of natural gas and the definition of major gas source rocks in the Baiyun Sag of the Pearl River Mouth Basin have attracted extensive attention from scholars. There is still considerable controversy over the genesis and the main gas source rocks of natural gas. In this study, the chemical kinetics method of natural gas generation and carbon isotope fractionation was used to study the generation history and isotope evolution history of Paleogene natural gas in the Y5 well area located on the north slope of Baiyun Sag. And other geochemical discriminant methods were applied simultaneously to determine the type and source rocks of natural gas. The results show that the natural gas in the Y5 well area on the northern slope of Baiyun Sag is mainly kerogen degradation gas, mixed with a small amount of oil cracking gas. The mixture of kerogen degradation gas and a small amount of crude oil cracking gas caused the inversion of the carbon isotope sequence of ethane and propane. The natural gas in the Y5 well area mainly comes from delta–shallow lacustrine facies source rock. The high–quality reservoirs in the shallower strata accumulate natural gas generated in the early stage, and the tight reservoirs in the deeper strata mainly accumulate natural gas generated in the late stage.

One of the rapidly developing research areas in the power system is the integration of distributed generation (DG) with the distribution system. The size and location of DG sources had a considerable impact on power system networks. Artificial intelligence (AI) techniques can be used to address multidimensional problems relating to DG size and location in distribution systems. Heuristic optimization offers a reliable and effective method for solving complicated real-world problems. This work focuses on a hybrid approach that combines the two heuristic optimization methods i.e., Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) for the optimal siting and sizing of DG in distribution systems. This hybrid approach combines ideas from GA and PSO and generates individuals in a new generation using both PSO mechanisms and the procedures found in GA. An extensive performance analysis of the IEEE 14 busbar standard test system is conducted to demonstrate the viability of the suggested methodologies. In the designated locations, DG is placed, and the outcomes have been verified. The results indicated that the right placement of DG injection enhances the voltage profile and lowers the distributed system’s power losses. These techniques offer unique methods for determining the location of the DG unit, demonstrating the potential of such a computational techniques to reduce computing time and complexity while simultaneously reducing human errors associated with hit-and-trail methods.

Abstract: The diffusion of competition under the coexistence of multi-generation products has become one of the important challenges faced by enterprises in their daily and sustainable operations. At the same time, the competition between different brands has intensified the difficulty and complexity of decision-making in the process of multi-generation product operation, Therefore, based on the Norton-Bass model diffusion process, this paper introduces two marketing variables, dynamic price and quality level, builds a multi-generation product diffusion model under the dual-brand competition, and analyzes the impact of the company's revenue on the launch time to market, pricing, quality or technical level. By using system dynamics (SD) method, From the perspective of strong brand and weak brand enterprises, the competition diffusion model is built and simulated. The simulation shows that: i) When enterprises have the same brand competitiveness, reducing the pricing level cannot obtain more revenue, but diminish the overall revenue of the industry; Raising the pricing level can get more revenue, but also improve the revenue of competitors. ii) When the competitive strength of enterprises is different, the strong brand tends to maintain a stable pricing on the basis of improving the quality level, or slightly raise the price. Weak brands tend to raise the pricing of new products significantly on the basis of improving the quality level. iii) The launch time to market decision of new product is influenced by the degree of product quality upgrade. Therefore, the frequency of releasing new products should trade-off against the degree of technological upgrading of product quality. This paper provides the theoretical basis and new insights for the new product launch and operation decision of enterprises.

The crystal structure of a polymorph of Glycyl-L-alanine HI.H2O was synthesized from chiral cyclic Glycyl-L-alanine dipeptide, known to show molecular flexibility in different environments. The space group is polar (P21) and therefore pyroelectricity and optical second harmonic generation properties are allowed by symmetry. We report a pyroelectric coefficient as high as 45 µC/m2K occurring at 345 K, one order of magnitude smaller than the semi-organic ferroelectric Triglycine Sulphate (TGS) crystal. Furthermore, the polymorph displays a nonlinear optical effective coefficient of 0.14 pm/V, around 14 times smaller than the value from a phase-matched inorganic Barium Borate (BBO) single crystal.

The article analyzes existing materials and structures with quadratic-nonlinear optical properties that can be used to generate a difference frequency in the terahertz and sub-terahertz frequency ranges. The principle of constructing a nonlinear optical-radio converter, based on an optical focon (a focusing cone), is proposed. Based on the assumption that this focon can be implemented from the metal-organic framework (MOF), we propose a technique for modeling its parameters. The mathematical model of the process of propagation and nonlinear interaction of waves inside the focon is based on a simplification of the nonlinear wave equation. Within the framework of the developed model, the following parameters are approximately determined: the 3D gradient of the linear refractive index and the function determining the geometric profile of the focon, which provide a few-mode-based generation of the difference frequency.

The global climate change mitigation efforts have increased the efforts of national government to incentivize local households in adopting individual renewable energy as a mean to help reduce the usage of electricity generated using fossil fuels and to gain independence from the grid. Since the majority of residential generation is made by PV panels that generate electricity at off-peak hours, the optimal management of such installations often considers local storage that can defer the use of locally generated electricity at later times. On the other hand, the presence of distributed generation can affect negatively the operating conditions of low-voltage distribution networks. The energy stored in batteries located in optimal places in the network can be used by the utility to improve the operation of the network. This paper proposes a metaheuristic approach based on a Genetic Algorithm that considers three different scenarios of using energy storage for reducing the losses in the network. Prosumer and network operator priorities can be considered in different scenarios inside the same algorithm, to provide a comparative study of different priorities in storage placement. A case study performed on a real distribution network provides insightful results.

We report on the application of femtosecond laser micromachining to the fabrication of complex glass microdevices, for high-order harmonic generation in gas. The three-dimensional capabilities and extreme flexibility of femtosecond laser micromachining allow us to achieve accurate control of gas density inside the micrometer interaction channel. This device gives a considerable increase in harmonics generation efficiency if compared with traditional harmonic generation in gas jets. We propose different chip geometries that allow to control the gas density and driving field intensity inside the interaction channel to achieve quasi-phase matching conditions in the harmonic generation process. We believe that these glass micro-devices will pave the way to future downscaling of High-order Harmonic Generation beamlines.

A numerical approach for generating a limited number of water demand scenarios and estimating their occurrence probabilities in a Water Distribution Network (WDN) is proposed. This approach makes use of the demand scaling laws in order to consider the natural variability and spatial correlation of nodal consumptions. The scaling laws are employed to determine the statistics of nodal consumption as a function of the number of users and the main statistical features of the unitary user's demand. Besides, consumption at each node is considered to follow a Gamma probability distribution. A high number of groups of cross-correlated demands, i.e., scenarios, for the entire network were generated using Latin Hypercube Sampling (LHS) and the numerical procedure proposed by Iman and Conover. The Kantorovich distance is used to reduce the number of scenarios and estimate their corresponding probabilities, while keeping the statistical information on nodal consumptions. By hydraulic simulation, the whole number of generated demand scenarios was used to obtain a corresponding number of pressure scenarios on which the same reduction procedure was applied. The probabilities of the reduced scenarios of pressure were compared with the corresponding probabilities of demand.

Although microgrids facilitate the increased penetration of distributed generations (DGs) and improve the security of power supplies, they have some issues that need to be better understood and addressed before realising the full potential of microgrids. This paper presents a comprehensive list of challenges and opportunities supported by a literature review on the evolution of converter-based microgrids. The discussion in this paper presented with a view to establishing microgrids as distinct from the existing distribution systems. This is accomplished by, firstly, describing the challenges and benefits of using DG units in a distribution network and then those of microgrid ones. Also, the definitions, classifications and characteristics of microgrids are summarised to provide a sound basis for novice researchers to undertake ongoing research on microgrids.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

This study was undertaken to forecast waste generation rates of accommodation sector of North Cyprus as a case. Three predictor models including multiple linear regression (MLR), artificial neural networks (ANNs) and central composite design (CCD) were applied to predict the waste generation rate during the lean and peak seasons. ANN showed highest prediction performance, specifically, lowest values of the standard error of prediction (SEP = 2.153), mean absolute error (MAE=1.378) and highest R2 value (0.998) confirmed the accuracy of the model. The analysed wastes were categorised into recyclable, general waste and food residues. The authors estimated the total waste generated during the lean season as 2010.5 kg/day, in which large-sized hotel accounted for largest fraction (66.7%), followed by the medium hotels (19.4%) and guesthouse accounted for smallest part (2.6%). During the peak season, about 49.6% increases in the waste generation rates were obtained. Interestingly, 45% of the wastes were generated by the British tourists while the least waste was generated by African tourists (7.5%). The ANN predicted that the small and large hotels would produce 5.45 and 22.24 tons of waste by the year 2020, respectively. The findings herein are promising and useful in establishing a sustainable waste management system.

In this work, we explore Conjecture 1 proposed in the newly released pioneering paper “Volatility transformers: an optimal transport-inspired approach to arbitrage-free shaping of implied volatility surfaces” by Zetocha Valer, which posits that the “One-X” property is both a necessary and sufficient condition for convex order between non-negative continuous strictly increasing distributions with the same mean. We provide a counterexample demonstrating that the conjecture, as originally stated, does not hold. By examining stochastic orders, particularly the increasing convex order, and the “One-X” property, we propose an enhanced version of the conjecture which is shown to be valid. Furthermore, we discuss the implications of these findings in the context of equity implied volatility fitting and the construction of implied volatility surfaces, highlighting the challenges posed by real-market conditions. In the end, we propose several applications in implied volatility surface construction or simulation.

This study investigates job satisfaction, burnout, and well-being among first-generation migrant physicians in anesthesia and intensive care medicine in Germany, comparing them to their native German counterparts. Utilizing a cross-sectional survey design, the study collected data from 513 physicians, 110 of whom identified as having a migration background. Job satisfaction was measured using the German version of the Warr-Cook-Wall (WCW) Job Satisfaction Scale, burnout was assessed with the Copenhagen Burnout Inventory (CBI), and well-being was evaluated using the WHO-5 Well-Being Index. The job satisfaction ratings revealed no significant differences between migrant and German physicians in most dimensions, including physical workload, freedom to choose work methods, satisfaction with colleagues, responsibility, income, skill utilization, and variety in work tasks. However, migrant physicians reported significantly higher satisfaction with recognition received for their work and lower dissatisfaction with working hours. Burnout assessments showed that migrant physicians experienced higher psychological strain, perceiving every work hour as more exhausting and having significantly less energy for family and friends. Notably, migrant physicians reported higher difficulty and frustration in working with patients. Well-being ratings indicated that migrant physicians felt less energetic and active but found their daily life more filled with interesting activities. The findings underscore the unique challenges faced by migrant physicians, particularly in terms of recognition and patient-related burnout. These results highlight the need for targeted interventions to support migrant physicians, including cultural competence training and flexible working hours to enhance their job satisfaction and overall well-being. Addressing these issues is crucial for maintaining the quality of patient care and the occupational health of migrant physicians in Germany.

This paper addresses the mixed convective flow and heat transfer in combustible third grade fluid through a slant channel that is filled with a permeable materials. The fluid layer in contact with the lower plate is exposed to convective heating with the ambient while at the upper plate, a constant heat flux is experienced. We employ the spectral quasilinearisation method (SQLM) to the coupled nonlinear flow governing equations. Fluid velocity and temperature profiles, local entropy generation and irreversibility ratio are computed and analysed quantitatively and qualitatively. A residual error analysis demonstrated high accuracy and convergence of the numerical method. The results on flow and thermal effects, entropy generation rate and Bejan number revealed fascinating manifestations that have profound implications in design of thermo-mechanical systems. In particular, the results of the thermal analysis are pertinent to optimal designs of systems that achieve efficient energy utilization.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

Many advanced technologies have been employed in the high performance active matrix displays including liquid crystal displays, organic light emitting diode displays, and micro light emitting diode displays. On the other side, there have existed the strong demand on the cost reduction and it is one of low cost schemes to integrate the driver circuit in a panel based on thin film transistor technologies. This paper reviews overall concept, operation principles, and various circuit approaches in shift registers for the scanning pulse generation. In addition, it deals with the implementation of additional functionalities in gate drivers to support pixel compensation, multi-line driving, in-cell capacitive touch screen, pixel sensing, and adaptive scanning region control.

Background: Study to assess glucose levels of people with type 1 diabetes (T1D) overnight based on insulin type and timing. Methods: Real-world, retrospective study in T1D using multiple daily insulin injections. Contin-uous glucose monitoring and insulin injections data were collected for ten hours after dinner us-ing the Insulclock® connected cap. Meal events were identified using ROC detection methodology. The timing of rapid insulin, second injections, and the type of insulin analogs used were evaluat-ed. Results: Nocturnal profiles (n=775, 49 subjects) were analyzed. Higher glucose AUC over 180mg/dL was observed in delayed injections (number; %; mg/dL x h): -45-15min (n=136; 17.5%, 175.9 ±271.0); -15-0min (n= 231; 29.8%, 164.0 ±237.1); 0+45min (n= 408; 52.6%, 203.6 ±260.9), (p 0.049). The use of ultrarapid (FiAsp®) (URI) vs rapid insulin analogs (RI) was associated with less hypoglycemia events (7.1 vs 13.6%; p 0.005) and TBR70 (1.7 +6.9 vs 4.6 +13.9%; p 0.003). Us-ers of glargine U300 vs degludec had higher TIR (70.7 vs 58.5 %) (Adjusted R-squared: 0.22, p < 0.001). The use of a correction injection (n= 144, 18.6%) was associated with higher hypoglycemia events (18.1 vs 9.5%; p 0.003), TBR70 (5.5 +14.2 vs 3.0 +11.1%; p 0.003), glucose AUC over 180 mg/dL (226.1 +257.8 vs 178.0 +255.3 mg/dL x h; p 0.001), and lower TIR (56.0 +27.4 vs 62.7 +29.6 mg/dL x h; p 0.004). Conclusions: Dinner rapid insulin timing, insulin types and correction injections affect nocturnal glucose profile in T1D.

Cancer cells show altered antioxidant defense systems, dysregulated redox signaling, and increased generation of reactive oxygen species (ROS). Targeting cancer cells through ROS-mediated mechanisms has emerged as a significant therapeutic strategy due to its implications in cancer progression, survival, and resistance. Extensive research has focused on selective generation of H2O2 in cancer cells for selective cancer cell killing by employing various strategies such as metal-based prodrugs, photodynamic therapy, enzyme-based systems, nano-particle mediated approaches, chemical modulators, and combination therapies. Many of these H2O2-amplifying approaches have demonstrated promising anticancer effects and selectivity in preclinical investigations. They selectively induce cytotoxicity in cancer cells while sparing normal cells, sensitize resistant cells, and modulate the tumor microenvironment. However, challenges remain in achieving selectivity, addressing tumor heterogeneity, ensuring efficient delivery, and managing safety and toxicity. To address those issues, H2O2-generating agents have been combined with other treatments leading to optimized combination therapies. This review focuses on various chemical agents/approaches that kill cancer cells via H2O2-mediated mechanisms. Different categories of compounds that selectively generate H2O2 in cancer cells are summarized, their underlying mechanisms and function are elucidated, preclinical and clinical studies as well as recent advancements are discussed, and their prospects as targeted therapeutic agents and their therapeutic utility in combination with other treatments are explored. By understanding the potential of these compounds, researchers can pave the way for the development of effective and personalized cancer treatments.

This research explores the behaviors of Generation Z consumers in China, particularly focusing on their interaction with companies through social media for the joint creation of value. Adopting a qualitative methodology, the research initially constructs a scale for assessing co-creation of value on social media platforms. Subsequently, it delves into the motivational aspects of users' engagement in these co-creative activities. The study unveils a range of utilitarian and hedonic motivations that drive Generation Z's value co-creation actions on social media. Insights derived from the findings offer both theoretical and practical implications for the field.

Since the creation of the first parallel electrical power systems around the world, the rotor angle stability of synchronously operating generators has been one of the most crucial and challenging problems. In modern electricity networks, involving Kazakhstani, where the renewable energy technologies are rapidly penetrating, and the issue of stability takes on even greater importance due to the technical shortcomings of inverter-based generation. In this framework, an analysis of rotor angle transient stability was carried out when replacing existing synchronous generators with doubly fed induction generators under a certain pre-emergency mode. A critical proportion of active power generation by DFIG units was identified at which transient stability can still be maintained due to the sufficient stored kinetic energy of the synchronous machines remaining in operation. In addition, 2 simple solutions were investigated to improve transient stability, such as an increased time of the automatic reclosure operation and the use of special load shedding automation. For the analysis, a real power system of Mangystau region in Kazakhstan was considered, and the PowerWorld software was used.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

This comprehensive review explores the principles, applications, and future directions of human-powered energy generation technologies. It begins by providing a detailed examination of viable human energy sources, elucidating the physical principles behind various energy harvesting devices. The review then compiles and assesses existing products in the field of human power generation, while also outlining the opportunities and challenges it presents. Finally, an innovative concept of an eco-village system is introduced to demonstrate a future potential application scenario for human-generated electricity. It outlines two developmental stages for this system and underscores its significance in the construction of the harmonious and sustainable communities. This forward-thinking approach could pave the way for broader discussions on sustainable living and eco-friendly energy generation in a world increasingly focused on environmental concerns and social stability.

To realize fast and effective synthetic aperture radar (SAR) deception jamming, a high-quality SAR deception jamming template library can be generated by performing sample augmentation on SAR deception jamming templates. However, current sample augmentation schemes of SAR deception jamming templates face certain problems. First, the authenticity of templates is low due to the lack of speckle noise. Second, the generated templates have low similarity to the target and shadow areas of the input templates. To solve these problems, this study proposes a sample augmentation scheme based on generative adversarial networks, which can generate a high-quality library of SAR deception jamming templates with shadows. The proposed scheme solves the two aforementioned problems from the following aspects. First, the influence of the speckle noise is considered in the network to avoid the problem of reduced authenticity in generated images. Second, a channel attention mechanism module is used to improve the network's learning ability of shadow features, which improves the similarity between the generated template and the shadow area in the input template. Finally, the proposed scheme and the SinGAN scheme are compared regarding the equivalent numbers of looks and the structural similarity between the target and shadow in the sample augmentation results. The comparison results demonstrate that, compared to the templates generated by the SinGAN scheme, those generated by the proposed scheme have targets and shadow features similar to those of the original image, and can incorporate speckle noise characteristics, resulting in higher authenticity, which helps to achieve fast and effective SAR deception jamming.

Here we report a new synthetic protocol based on Microwave- Assisted Synthesis (MAS) for the preparation in higher yields of zinc and copper MOFs based on different bis(pyrazolyl)-tagged ligands ([M(BPZ)]n where M = Zn(II), Cu(II), H2BPZ = 4,4′-bipyrazole, [M(BPZ-NH2)]n where M = Zn(II), Cu(II); H2BPZ-NH2 = 3-amino-4,4’-bipyrazole, and [Mx(Me4BPZPh)] where M = Zn(II), x = 1; Cu(II), x = 2; H2Me4BPZPh = bis-4′-(3′,5′-dimethyl)- pyrazolylbenzene) and a detailed study of their antibacterial activity, tested against Gram-negative (E. coli) and Gram-positive (S. aureus) bacteria, as representative agents of infections. The results show that all MOFs exert a broad-spectrum activity and strong efficiency in bacterial growth inhibition, with a mechanism of action based on surface contact of MOFs particles with bacterial cells through the so-called “chelation effect” and reactive oxygen species (ROS) generation, without a significant release of Zn(II) and Cu(II) ions. In addition, morphological changes were elucidated by using scanning electron microscope (SEM) and bacterial cell damage was further confirmed by confocal laser scanning microscopy (CLSM) test.

The objective of this study is to clarify the effect of restoring the lowered masticatory muscle functional pressure and correcting the imbalance of bilateral masticatory muscle functional pressure on jawbone growth during growth and development with quantitative evaluation of the changes in micro/nanostructural characteristics of entheses. Male Wistar rats aged 4 weeks were divided into an experimental group injected with a botulinum toxin serotype A (BoNT/A) formulation to reduce muscle function (BTX group) and a control group (CTRL group). They were euthanized after 6, 8, 10, 12, and 16 weeks after measuring the difference between the midline of the upper and lower incisors. The mandibles were harvested for histological examination, second harmonic generation imaging, and quantitative evaluation of biological apatite (BAp) crystal alignment. The midline difference decreased with age in weeks. In rats from 6 weeks after BoNT/A administration to 12 weeks after administration, collagen fibre bundle diameter was significantly smaller in the BTX group; the difference between the two groups decreased with increasing age. BAp crystal alignment was significantly different on the X-axis and the Y-axis on the BTX group from 6 weeks after BoNT/A administration to 10 weeks after administration. Asymmetry of mandibular bone formation caused by load imbalance during growth could be corrected by adjustment of the function of the masseter muscle on either side.

Activated platelets are involved in blood coagulation by exposing phosphatidylserine (PS), which serves as a substrate for assembling coagulation complexes. Platelets accelerate fibrin formation and thrombin generation, two final reactions of the coagulation cascade. We investigated the effects of antiplatelet drugs on platelet impact in these reactions and platelet ability to expose PS. Washed human platelets were incubated with acetylsalicylic acid (ASA), ticagrelor, ASA in combination with ticagrelor, ruciromab (glycoprotein IIb-IIIa antagonist) or prostaglandin E1 (PGE1). Platelets were not activated or activated by collagen, sedimented in multiwell plates and plasma was added after supernatant removal. Fibrin formation (clotting) was monitored in a recalcification assay by light absorbance and thrombin generation in a fluorogenic test. PS exposure was assessed by annexin V staining using flow cytometry. Ticagrelor (alone and in combination with ASA), ruciromab and PGE1, but not ASA prolonged the lag phase and decreased the maximum rate of plasma clotting, and decreased the peak and maximum rate of thrombin generation. Inhibition was observed when platelets were not treated with exogenous agonists (activation by endogenous thrombin) and pretreated with collagen. Ticagrelor (alone and in combination with ASA), ruciromab and PGE1, but not ASA decreased PS exposure on washed platelets activated by thrombin and by thrombin + collagen. PS exposure on activated platelets in whole blood was lower in patients with acute coronary syndrome receiving ticagrelor + ASA in comparison with donors free of medications. These results indicate that antiplatelet drugs are able to suppress platelet coagulation activity not only in vitro but also after administration to patients.

Novel TFN membranes were examined for the removal of heavy metals (Cu and Pb) from synthetic wastewater in forward osmosis (FO) experiments using MgCl2 as a draw solute. The TFN membranes were fabricated on top of a commercial PS35 ultrafiltration membrane by in-situ interfacial polymerization of piperazine (PIP) and 1,3,5-benzenetricarbonyl trichloride (TMC) containing different amounts of dispersed functionalized halloysite nanotubes (HNTs) nanoparticles. The HNTs nanoparticles were functionalized with the first generation of poly(amidoamine) (PAMAM) dendrimers. The TFN and the control TFC membranes showed rejections of Cu2+ and Pb2+, ranging from 94.5% to 98.1%. The presence of heavy metal in the feed solution enhanced the FO performance of all membranes. In particular, the reverse flux of MgCl2 decreased at least 2.5 times compared to the experiments with pure water as a feed. Simultaneously, the water flux also increased. The improved FO performance of the membranes in the presence of heavy metal ions is attributed to their adsorption by the membranes. The adsorption of heavy metals was confirmed by a decrease in the negativity of zeta potential and the results from inductively coupled plasma mass spectrometry (ICP-MS) of the membranes after the FO experiments.

The proliferation of devices for the Internet of Things (IoT) and their implication in many activities of our lives have led to a considerable increase in concern about the security of these devices, posing a double challenge for designers and developers of products. On the one hand, the design of new security primitives, suitable for resource-limited devices, that can facilitate the inclusion of mechanisms and protocols to ensure the integrity and privacy of the data exchanged over the Internet. On the other hand, the development of techniques and tools to evaluate the quality of the proposed solutions as a step prior to their deployment, as well as to monitor their behavior once in operation against possible changes in operating conditions arising naturally or as a consequence of a stress situation forced by an attacker. To address these challenges, this paper first describes the design of a security primitive that plays an important role as a component of a hardware-based root of trust, as it can act as a source of entropy for true random number generation (TRNG) or as a physical unclonable function (PUF) to facilitate the generation of identifiers linked to the device on which it is implemented. The work also illustrates different software components that allow carrying out a self-assessment strategy to characterize and validate the performance of this primitive in its dual functionality, as well as to monitor possible changes in security levels that may occur during operation as a result of device aging and variations in power supply or operating temperature. The designed PUF/TRNG is provided as a configurable IP module, which takes advantage of the internal architecture of the Xilinx Series-7 and Zynq-7000 programmable devices and incorporates an AXI4-based standard interface to facilitate its interaction with soft- and hard-core processing systems. Several test systems that contain different instances of the IP have been implemented and subjected to an exhaustive set of on-line tests to obtain the metrics that determine its quality in terms of uniqueness, reliability, and entropy characteristics. The results obtained prove that the proposed module is a suitable candidate for various security applications. As an example, an implementation that uses less than 5% of the resources of a low-cost programmable device is capable of obfuscating and recovering 512-bit cryptographic keys with virtually zero error rate.

Machine Learning (ML) methods have become important to enhance the performance of decision-support predictive models. However, class imbalance is one of the main challenges for developing ML models, because it limits the generalization of these models, and biases the learning algorithms. In this paper, we consider oversampling methods for generating synthetic categorical clinical data aiming to improve the predictive performance in ML models, and the identification of risk factors for cardiovascular diseases (CVDs). We performed a comparative study of several categorical synthetic data generation methods, including Generative Adversarial Networks (GANs). Then, we assessed the impact of combining oversampling strategies and linear and nonlinear supervised ML methods. Lastly, we conducted a post-hoc model interpretability based on the importance of the risk factors. Experimental results show the potential of GAN-based models for generating high-quality categorical synthetic data, yielding probability mass functions that are highly close to real data, maintaining relevant insights, and contributing to increase the predictive performance. The GAN-based model and a linear classifier outperforms other oversampling techniques, improving 2\% the area under the curve. These results demonstrate the capability of synthetic data to help both in determining risk factors and building models for CVD prediction.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

The age of information (AoI) metric was proposed to measure the freshness of messages obtained at the terminal node of a status updating system. In this paper, the AoI of discrete time status updating system with probabilistic packet preemption is investigated by analyzing the steady state of a three-dimensional discrete stochastic process. Assuming the queue used in system is Ber/Geo/1/2*/η, which represents that the system size is 2 and the packet in buffer can be preempted by fresher packet with probability η. Instead of considering system’s AoI separately, we use a three-dimensional state vector (n,m,l) to simultaneously track the real time changes of the AoI, the age of packet in server, and the age of packet waiting in buffer. We give the explicit expression of system’s average AoI, and show that the average AoI of system without packet preemption is obtained by letting η=0. When η is set to 1, the mean of AoI of system having Ber/Geo/1/2* queue is obtained as well. Combining the results we have obtained and comparing them with corresponding average continuous AoIs, we propose a possible relationship between average discrete AoI with Ber/Geo/1/c queue and the average continuous AoI with M/M/1/c queue. For each of two extreme cases where η=0 and η=1, we also determine the stationary distribution of AoI using the probability generation function (PGF) method. The relations between average AoI and the packet preemption probability η, as well as AoI’s distribution curves in two extreme cases are illustrated by numerical simulations. Notice that the probabilistic packet preemption may occur, for example, in an energy harvest (EH) node of wireless sensor network, where the packet in buffer can be replaced only when the node collects enough energy. In particular, to exhibit the usefulness of our idea and methods and highlight the merits of considering discrete time systems, in this paper we give much more explanations showing that how the results about continuous AoI is derived by analyzing the corresponding discrete time system, and how the discrete age analysis is generalized to the system with multiple sources. In terms of packet service process, we also propose our idea to analyze system’s AoI when the service time distribution is relaxed to be arbitrary.

Voltage Stability & Control, is very crucial compared to other Power System (PS) Quality and Stability issues. Long-Vertical-Power-Flows in Conventional Grids, causes voltage drops which in turn causes huge power losses, especially in the Medium Voltage (MV) and Low Voltage (LV) Distribution Networks. Such technical losses in abysmally-planned weak distribution networks, lead to substantial loss of revenues to the utility grid. Apart from classic Voltage Regulation (VR) techniques, with the rise of Distributed Generation (DG) based on Renewable Energy Sources (RES), Horizontal-Power-Flows can be introduced in the network, through various Smart Grid techniques. Coupling such sources, near load centers shall mitigate long flows from expensive conventional sources at times of huge demands, improving feeders’ Voltage Profile. This Ancillary Service of Voltage Support from DG RESs shall thereby alleviate revenue losses caused by long-power-flows in weak distribution grids. For a developing country like Pakistan, loss of revenue from an already expensive utility gives huge blow to the economy. So, a similar technique for voltage support is proposed for an 11-kV feeder, which faces similar problem, and the results are remarkable. The technique is implemented using OpenDSS Tool by modelling 3MWp PV Penetration along with some future storage.

Photovoltaic (PV) generation is potentially uncertain. Probabilistic PV generation forecasting methods have been proposed with prediction intervals (PIs). However, several studies have dealt with geographically distributed PVs in a certain area. In this study, a two-step probabilistic forecast scheme is proposed for geographically distributed PV generation forecasting. Each step of the proposed scheme adopts ensemble forecasting based on three different machine-learning methods. In this case study, the proposed scheme was compared with conventional non-multistep forecasting. The proposed scheme improved the reliability of the PIs and deterministic PV forecasting results through 30 days of continuous operation with real data in Japan.

This research will examine the computational methods to calculate the nonlinear optical process of second harmonic generation (SHG) that will be hypothesized to be present during lithium ion insertion into silicon nanowires. First it will be determined whether the medium in which SHG is conveyed is non-centrosymmetric or whether the medium is inversion symmetric where SHG as a part of the second-order nonlinear optical phenomenon does not exist. It will be demonstrated that the main interaction that determines SHG is multiphoton absorption on lithium ions. The quantum harmonic oscillator (QHO) is used as the background that generates coherent states for electrons and photons that transverse the length of the silicon nanowire. The matrix elements of the Hamiltonian which represents the energy of the system will be used to calculate the probability density of second-order nonlinear optical interactions which includes collectively SHG, sum-frequency generation (SFG) and difference-frequency generation (DFG). As a result it will be seen that at varies concentrations of lithium ions (Li+) within the crystallized silicon (c-Si) matrix the second-order nonlinear optical process has probabilities substantial enough to create second harmonic generation that could possibly be used for such applications as second harmonic imaging microscopy.

Hopfield Neural Networks (HNNs) are recurrent neural networks used to implement associative memory. Their main feature is their ability to pattern recognition, optimization, or image segmentation. However, sometimes it is not easy to provide the users with good explanations about the results obtained with them due to mainly the large number of changes in the state of neurons (and their weights) produced during a problem of machine learning. There are currently limited techniques to visualize, verbalize, or abstract HNNs. This paper outlines how we can construct automatic video generation systems to explain their execution. This work constitutes a novel approach to get explainable artificial intelligence systems in general and HNNs in particular building on the theory of data-to-text systems and software visualization approaches. We present a complete methodology to build these kinds of systems. Software architecture is also designed, implemented, and tested. Technical details about the implementation are also detailed and explained. Finally, we apply our approach for creating a complete explainer video about the execution of HNNs on a small recognition problem.

We introduce firm solar forecasts as a strategy to operate optimally overbuilt solar power plants in conjunction with optimally sized storage systems so as to make up for any power prediction errors, hence entirely remove load balancing uncertainty emanating from grid-connected solar fleets. A central part of this strategy is plant overbuilding that we term implicit storage. We show that strategy, while economically justifiable on its own account, is an effective entry step to least-cost ultra-high solar penetration where firm power generation will be a prerequisite. We demonstrate that in absence of an implicit storage strategy, ultra-high solar penetration would be vastly more expensive. Using the New York Independent System Operator (NYISO) as a case study, we determine current and future cost of firm forecasts for a comprehensive set of scenarios in each ISO electrical region, comparing centralized vs. decentralized production and assessing load flexibility’s impact. We simulate the growth of the strategy from firm forecast to firm power generation. We conclude that ultra-high solar penetration enabled by the present strategy, whereby solar would firmly supply the entire NYISO load, could be achieved locally at electricity production costs comparable to current NYISO wholesale market prices.

Induction machines drive many industrial processes, and their unexpected failure can cause heavy production losses. The analysis of the current spectrum can identify online the characteristic fault signatures at an early stage, avoiding unexpected breakdowns. Nevertheless, frequency domain analysis requires stable working conditions, which is not the case for wind generators, motors driving varying loads, etc. In these cases an analysis in the time-frequency domain -such as a spectrogram- is required for detecting faults signatures. The spectrogram is built using the short frequency Fourier transform, but its resolution depends critically on the time window used to generate it: short windows provide good time resolution, but poor frequency resolution, just the opposite than long windows. Therefore, the window must be adapted at each time to the shape of the expected fault harmonics, by highly skilled maintenance personnel. In this paper, this problem is solved with the design of a new multi-band window, which generates simultaneously many different narrow-band current spectrograms, and combines them into a single, high resolution one, without the need of manual adjustments. The proposed method is validated with the diagnosis of bar breakages during the start-up of a commercial induction motor.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

In this research work the study of Buongiorno Model Darcy Forchheimer flow of Hybrid nanofluid flow on isothermal permeable stretch/shrink sheet with homogeneous and heterogeneous reaction is investigated. The effects of MHD, thermal radiation, viscous dissipation, Joule heating, and heat generation/absorption are taken into account. Hybrid nanofluids can act as a medium for heterogeneous-homogeneous reactions. The nanoparticles dispersed in the fluid can influence reaction kinetics and species transport, potentially, altering reaction rates and pathways. The applications of HNF in reactions, both homogeneous and heterogeneous, lie in leveraging their enhanced thermal properties, catalytic potential, and improved mixing capabilities to optimize reaction efficiency and control reaction conditions. Similarity transformation is used to convert a set of PDEs into a set of ODEs. HAM is used for the solution of the obtained ODEs system. In a heterogeneous reaction, the concentration gradient is amplified; in a homogeneous reaction, the impact is opposite. Moreover, at higher compositions of HNPs, the concentration and velocity rise while the temperature falls. Furthermore, as the values of homogeneous and heterogeneous reactions increase, the concentration falls. It is reliable with the idea that a greater reaction rate lowers the diffusion rate. Nevertheless, these parameters do not affect temperature or velocity.

Exergy analysis evaluates the efficiency of system components by quantifying the rate of entropy generation. In general, the exergy destruction rate or irreversibility rate was directly obtained through the exergy-balance equation. However, this method cannot determine the origin of the component's entropy generation rate, which is a very important factor in system design and improvement. In this study, a thorough energy, exergy thermoeconomic analysis of a proton exchange membrane fuel cell (PEMFC) was performed, providing the heat transfer rate, entropy generation rate and cost loss rate of each component. The irreversibility rate of each component is obtained by the Gouy-Stodolar theorem. Detailed and extensive exergy and thermoeconomic analyses of PEMFC system have determined that water cooling units experience the greatest heat transfer among the components in the studied PEMFC system, resulting in the greatest irreversibility and thus the greatest monetary flow loss.

Building energy demand impacts a myriad of interconnected economic, societal, and environmental aspects. As a result, Buildings Energy Models (BEM) play an important role in the process of urban design and planning. While previous studies have investigated the effects of building interventions on energy efficiency, their applicability may be limited due to the BEM’s high computational complexity. This limits their ability to systematically study important aspects of energy demand on a large scale. The development of Machine Learning Models (MLM) allows to design the required detailed analysis and solutions, while reducing the computational burden, making MLM attractive for urban designers. The capability of MLM to generalize well for multiple contexts (in our case, multiple buildings) is a crucial contributor to their applicability. However, the validation process in a wider context is often overlooked, therefore its generalization capabilities are not quantified. In this paper, we present a framework to train and validate a surrogate model derived from a physics-based BEM. Our method employs a Multiple Linear Regression model to predict Energy Use Intensity (EUI) for office buildings in Singapore using 36 input parameters (covariates), based on a training dataset of 23,000 samples. Model validation is performed by comparing the results of the Surrogate Model (SM) to a widely used BEM for a sample of 120 buildings. Our results indicate that the SM has an accuracy of NRMSE of 13%, NMBE of −3.56%, and R2 of 0.92, which suggests it can effectively and accurately predict building EUI. We also conduct a sensitivity analysis, which indicates that the parameters associated with internal loads and internal space usage are the most influential. Additionally, we present a reduced order model trained with only the 11 most influential parameters, which exhibits negligible loss in accuracy compared to the full SM while providing reduced complexity. Finally, we demonstrate an application of our SM to evaluate energy efficiency under uncertainty scenarios. The analytically derived results indicate a potential reduction of EUI of offices in Singapore from 227kWh/m2 to 99kWh/m2 by altering the building parameters that were identified as most influential.

Generative models have recently gained popularity in Remote Sensing, offering substantial benefits for interpreting and utilizing satellite imagery across diverse applications such as climate monitoring, urban planning, and wildfire detection. These models are particularly adept at addressing the challenges posed by satellite images, which often exhibit domain variability due to seasonal changes, sensor characteristics, and especially variations in spectral bands. Such variability can significantly impact model performance across various tasks. In response to these challenges, our work introduces a novel approach that harnesses the capabilities of Generative Adversarial Networks (GANs), augmented with Contrastive Learning, to generate target domain images that account for multi-spectral band variations effectively. By maximizing mutual information between corresponding patches and leveraging the power of GANs, our model aims to generate realistic-looking images across different multi-spectral domains. We present a comparative analysis of our model against other well-established generative models, demonstrating its efficacy in generating high-quality satellite images while effectively managing domain variations inherent to multi-spectral diversity.

Ultralight power generation equipment has high requirements for the power density, continuous operation, and transient stability of the whole machine, and there is a direct conflict between high power density design and substantial stability control in the power unit design. In order to meet the power density requirements of ultra-light power stations, three main problems need to be solved, namely engine speed oscillation and flameout in the process of load power mutation, matching of the generator and engine torque, and stabilizing the voltage waveform of the AC output end. In this paper, we proposed an exquisite control strategy for ultralight power generation systems in engines, generators, and inverters. The effectiveness and practicability of the proposed strategy are verified by both simulation and experiment. The results show that the proposed control strategy can effectively solve the instability problem of the ultralights generator set and improve the stability of the system, where the response recovery can be achieved within 0.9 seconds under the condition of total load increase or decrease, and the mismatching degree of the generator following the engine is reduced by 90%. The strategy could also guarantee long-term stable operation with high-quality electrical energy output.

This paper presents a design and performance analysis of a 10-element 5G massive MIMO antenna array for sub-6GHz mobile handsets, specifically for LTE bands 42 (3400-3600 MHz), 43 (3600-3800 MHz), 48/49 (3550-3700 MHz) applications. The proposed antenna array consists of 10 closely spaced linearly polarized inverted-F antennas with a compact size of 20 × 9 mm2 of a single element. The proposed antenna array provides high gain, high efficiency, and low correlation between the antenna elements, which results in improved channel capacity, increased data rate, and enhanced signal quality. The performance of the antenna array is evaluated in terms of the radiation pattern, gain, efficiency, and correlation coefficient. The simulation and measured results show that the proposed antenna array achieves an approximate peak gain of 3.1 dBi at the resonance frequency, a total efficiency of 65 %, and a low correlation coefficient of 0.06 between the antenna elements. Therefore, the proposed 5G massive MIMO antenna array is a promising candidate for sub-6 GHz mobile handsets, particularly for LTE bands 42/43/48/49 applications.

Energy demand and consumption in recent times have witnessed a rapid proliferation influenced by technological developments, increased population and economic growth. This has fuelled research trends in the domain of energy management employing tri-generation systems such as the combined cooling, heating and power (CCHP) systems. Furthermore, the incorporation of renewable energy, especially solar energy, to complement the thermal input by fossil fuels has facilitated the effectiveness and sustainability of CCHP systems. This study proposes a new approach to improve the overall efficiency of CCHP systems and compute the optimal design parameters in order to assist decision makers to identify the best geometrical configuration. A multi-objective optimization formulation of a solar-assisted CCHP system was adopted to maximize the net power, the exergy efficiency and minimize the CO2 emission using the greywolf optimization technique. In addition, the effects of the decision variables on the objective functions were analysed. The proposed optimization approach yielded 100 set of Pareto optimal solutions which would serve as options to the decision maker to make a selection in order to improve the performance of a solar-assisted CCHP system. This study demonstrates that the proposed approach is potentially suitable for the optimization of a solar-assisted CCHP system.

Protein-protein interactions (PPIs) are associated with various diseases; hence, they are important targets in drug discovery. However, the physicochemical empirical properties of PPI-targeted drugs are distinct from those of conventional small molecule oral pharmaceuticals, which adhere to the ”rule of five (RO5).” Therefore, developing PPI-targeted drugs using conventional methods, such as molecular generation models, is difficult. In this study, we propose a molecule generation model based on deep reinforcement learning, specialized for generating PPI inhibitors. By introducing a scoring function that can represent the properties of PPI inhibitors, we successfully generated potential PPI inhibitor compounds. The generated virtual compounds possess the desired properties for PPI inhibitors, and show similarity to commercially available PPI libraries. These generated virtual compounds are freely available as a virtual library.

Keeping the bus voltage within acceptable limits depends on dispatching reactive power. Power quality improves as a result of creating an effective power flow system, which also helps to reduce power loss. Therefore, Optimal Reactive Power Dispatch (ORPD) studies aim at designing appropriate system configurations to enable a reliable operation of power systems. Establishment of such a configuration is handled through control variables in power systems. On the other hand, installing Distributed Generation Unit (DGU) into a power system can have an important effect on power quality and power loss minimization. In this paper, Grey Wolf Optimization (GWO method is applied to ORPD problem for the first time, to find optimal placement of newly installed DGUs at the power system. Active power loss and voltage minimization have been minimized by optimizing the control variables while keeping them within their upper and lower bounds, and by finding the optimal placement of a newly installed DGU in power system. On the basis of IEEE 30 bus and IEEE 118 bus systems, performance of the suggested approach is investigated. A comparison is also performed among the proposed method and some other methods. Test results demonstrate that the resulting configuration contributes to growing the rate of renewable integration to a power system. The results also indicate that the suggested optimization approach applied to ORPD problem has improved power system performance in terms of both on power loss and voltage deviation. The promising results highlight the potential of the GWO algorithm to facilitate the integration of renewable power sources, and its role in promoting sustainable energy solutions.

In the era of electrification and artificial intelligence, direct current motors are widely utilized with numerous innovative adaptive and learning methods. Traditional methods utilize model-based algebraic techniques with system identification, such as recursive least squares, extended least squares, and autoregressive moving averages. The new method known as deterministic artificial intelligence asserts physical-based process dynamics to achieve target trajectory tracking. There are two common autonomous trajectory generation algorithms: sinusoidal function and Pontryagin's based generation algorithm. This thesis aims to simulate model-following and deterministic artificial intelligence methods using sinusoidal and Pontryagin's methods and compare their performance difference when following challenging step function slew maneuver.

The operational measure (OM) of the Second-Generation Intact Stability Criteria (SGISC) is the initial step toward the design of a performance-based dynamic stability assessment of the ship by considering both the vessel’s operation, loading condition and weather parameters. The SGISC recommends the standard wave scatter table (WST) for the environmental data, an indefinite requirement for a simplified assessment pathway, which provides the probability of wave occurrence. The existing standard WST was developed based on the North Atlantic Ocean. This study aims to identify the discrepancy in the probability of wave occurrence in the IMO-recommended WST when compared with developed hindcast WST for smaller regions of the North Atlantic Ocean for the application of SGISC. The significant difference in the existing standard WST is identified when compared with hindcast data, especially across different seasons. A case study of OM on the C11 class post-Panamax container ship for excessive acceleration is provided to better represent the study. The identified limitation limits the use of standard WST in ship stability assessment. The study recommends using hindcast-based WST for SGISC applications that are region and season based. This recommendation is beneficial in improving the safety assessment by OM, given the data is reliable and available for the season and region-specific, and hence the accuracy of the ship stability can be improved while using for the SGISC OM assessment. Further, it makes the WST adhere to the actual framework of the SGISC, i.e., using existing environmental data for design assessment and improving the simplified stability analysis.

Developing detailed Finite Element Models related to aerospace, automobile, civil, material science etc could be a very challenging task, especially generating a mesh that could produce accurate results. This review article provides an overview of different types of structural mechanics problems which are of interest to researchers and recent developments in meshing methodology related to each type of problems. The article also describes an automatic 2D mesh generation framework leverag- ing the capabilities of commercial FEA software MSC.PATRAN

Sources are classified into two depending upon the factor of reviving. These sources, which cannot be revived into their original shape once they are consumed, are considered as nonrenewable energy resources, i.e., (coal, fuel) Moreover, those energy resources which are revivable to the original condition even after being consumed are known as renewable energy resources, i.e., (wind, solar, hydel) Renewable energy is a cost-effective way to generate clean and green electrical energy Now a day’s majority of the countries are paying heed to energy generation from RES Pakistan is mostly relying on conventional energy resources which are mostly nonrenewable in nature coal, fuel is one of the major resources, and with the advent of time their prices are increasing on the other hand RES have great potential in the country with the deployment of RES greater reliability and an effective power system can be obtained In this thesis, a similar concept is being used and a hybrid power system is proposed which is composed of intermixing of renewable and nonrenewable sources The Source side is composed of solar, wind, fuel cells which will be used in an optimal manner to serve load The goal is to provide an economical, reliable, uninterruptable power supply. This is achieved by optimal controller (PI, PD, PID, FOPID) Optimization techniques are applied to the controllers to achieve the desired results. Advanced algorithms (Particle swarm optimization, Flower Pollination Algorithm) will be used to extract the desired output from the controller Detailed comparison in the form of tables and results will be provided, which will highlight the efficiency of the proposed system.

In the current era of ‘big data’, scientists are able to quickly amass enormous amount of data in a limited number of experiments. The investigators then try to hypothesize about the root cause based on the observed trends for the predictors and the response variable. This involves identifying the discriminatory predictors that are most responsible for explaining variation in the response variable. In the current work, we investigated three related multivariate techniques: Principal Component Regression (PCR), Partial Least Squares or Projections to Latent Structures (PLS), and Orthogonal Partial Least Squares (OPLS). To perform a comparative analysis, we used a publicly available dataset for Parkinson’ disease patien ts. We first performed the analysis using a cross-validated number of principal components for the aforementioned techniques. Our results demonstrated that PLS and OPLS were better suited than PCR for identifying the discriminatory predictors. Since the X data did not exhibit a strong correlation, we also performed Multiple Linear Regression (MLR) on the dataset. A comparison of the top five discriminatory predictors identified by the four techniques showed a substantial overlap between the results obtained by PLS, OPLS, and MLR, and the three techniques exhibited a significant divergence from the variables identified by PCR. A further investigation of the data revealed that PCR could be used to identify the discriminatory variables successfully if the number of principal components in the regression model were increased. In summary, we recommend using PLS or OPLS for hypothesis generation and systemizing the selection process for principal components when using PCR.rewordexplain later why MLR can be used on a dataset with no correlation

Cardiac myosin-binding protein C (MyBPC) is a thick-filament associated regulatory protein in the sarcomere. It regulates the sensitive contractile system of the myocardium by acting as a mechanical tether, sensitizing the thin filament or modulating myosin motor activity. Mutations in the MYBPC3 gene are a frequent cause for the development of hypertrophic cardiomyopathy, the most frequent cardiac disorder. Recently, the monoallelic double mutation MYBPC3Δ25bp/D389V has been discovered as a subset of the common MYBPC3Δ25bp variant in South Asia. MYBPC3Δ25bp/D389V carriers exhibit hyperdynamic features, which are considered an early finding for the development of hypertrophic cardiomyopathy. Using correlation-guided molecular dynamics simulations sampling, we show that the D389V mutation shifts the conformational distribution of the C2 domain of MyBPC. We further applied biochemical approaches to probe the effects of the D389V mutation on structure, thermostability and protein-protein interactions of MyBPC C2. The melting temperature (Tm) of MyBPC C2 D389V is decreased by 4 to 7 °C compared to wild type while the interaction of the C0-C2 domains with myosin and actin remains unchanged. Additionally, we utilized steered molecular dynamics (SMD) simulations to investigate the altered unfolding pathway of MyBPC C2 D389V. Based on our data, we propose a pathomechanism for the development of HCM in MYBPC3Δ25bp and MYBPC3Δ25bp/D389V carriers.

An in-depth study of the failure of granular materials, which is known as a mechanism to generate defects, can reveal the facts about the origin of the imperfections such as cracks in the carbon anodes. The initiation and propagation of the cracks in the carbon anode, especially the horizontal cracks below the stub-holes, reduce the anode efficiency during the electrolysis process. In order to avoid the formation of cracks in the carbon anodes, the failure analysis of coke aggregates can be employed to determine the appropriate recipe and operating conditions. In this paper, it will be shown that a particular failure mode can be responsible for the crack generation in the carbon anodes. The second-order work criterion is employed to analyze the failure of the coke aggregate specimens and the relationships between the second-order work, the kinetic energy, and the instability of the granular material are investigated. In addition, the coke aggregates are modeled by exploiting the discrete element method (DEM) to reveal the micro-mechanical behavior of the dry coke aggregates during the compaction process. The optimal number of particles required for the failure analysis in the DEM simulations is determined. The effects of the confining pressure and the strain rate as two important compaction process parameters on the failure are studied. The results reveal that increasing the confining pressure enhances the probability of the diffusing mode of the failure in the specimen. On the other hand, the increase of strain rate augments the chance of the strain localization mode of the failure in the specimen.

The aim of this articles is to investigate the entropy optimization in unsteady MHD flow Darcy-Forchheimer nanofluids towards a stretchable sheet. The surface we tend to think about is porous and stretchy under acceleration. Flow occurs due to the stretching of the surface. Four distinct types of aqueous nanostructures are taken in this examination where copper oxide ( ), copper ( ), titanium dioxide ( ) and aluminum oxide ( ) are the nanoparticles. Irreversibility analysis are discussed through second law of thermodynamics. The expression of energy is mathematically designed and discussed according to heat generation / absorption, dissipation, thermal radiation, and joule heating. The nonlinear PDE (partial differential conditions) is first changed to ODE (normal differential conditions) through appropriate similarity variables. Here we used the numerically embedded solution technique to develop a numerical result for the obtained nonlinear flow expression. Influence of various flow parameter velocity temperature distribution and entropy generation are discussed. Reduction occurs in velocity profile for larger porosity and magnetic parameters. An enhancement in entropy generation and temperature distribution is seen for Brinkman number. An opposite effect is noticed in velocity and temperature through solid volume friction.

This paper contains a concise overview of the deployment of scattered solar power plants in Poland, mainly from the perspective of their communication networks, and how the recent development of the Polish 4G networks has a very positive impact for the performance of the whole monitoring system (production control and video-surveillance), with a special emphasis on video-analytics, due to its higher bandwidth demand. All the information will be shown from the point of view of the solar photovoltaics developer I+D Energías, and therefore it constitutes a real user’s experience.

In the present work, we provide an electronic structure based method for the “on-the-fly” deter- mination of vibrational sum frequency generation (v-SFG) spectra. The predictive power of this scheme is demonstrated at the air-water interface. While the instantaneous fluctuations in dipole moment are obtained using the maximally localized Wannier functions, the fluctuations in polar- izability are approximated to be proportional to the second moment of Wannier functions. The spectrum henceforth obtained captures the signatures of hydrogen bond stretching, bending, as well as low-frequency librational modes.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.

We present a review of the current state of the field for a rapidly evolving group of technologies related to solar energy harvesting in built environments. In particular, we focus on recent achievements in enabling the widespread distributed generation of electric energy assisted by energy capture in semi-transparent or even optically clear glazing systems and building wall areas. Whilst concentrating on the cutting-edge recent results achieved in the integration of traditional photovoltaic device types into novel concentrator-type windows and glazings, we compare the main performance characteristics reported with these achievable using more conventional (opaque or semi-transparent) solar cell technologies. A critical overview of the current status and future application potential of multiple existing and emergent energy harvesting technologies for building integration is provided.

Time recordings of impulse-type oscillation responses are short and highly transient. These characteristics may complicate the usage of classical spectral signal processing techniques for a) describing the dynamics and b) deriving discriminative features from the data. However, common model identification and validation techniques mostly rely on steady-state recordings, characteristic spectral properties and non-transient behavior. In this work, a recent method, which allows reconstructing differential equations from time series data, is extended for higher degrees of automation. With special focus on short and strongly damped oscillations, an optimization procedure is proposed that fine-tunes the reconstructed dynamical models with respect to model simplicity and error reduction. This framework is analyzed with particular focus on the amount of information available to the reconstruction, noise contamination and non-linearities contained in the time series input. Using the example of a mechanical oscillator, we illustrate how the optimized reconstruction method can be used to identify a suitable model and to extract features from uni-variate and multivariate time series recordings in an engineering-compliant environment. Moreover, the determined minimal models allow for identifying the qualitative nature of the underlying dynamical systems as well as testing for the degree and strength of non-linearity. The reconstructed differential equations would then be potentially available for classical numerical studies, such as bifurcation analysis. These results represent a physically interpretable enhancement of data-driven modeling approaches in structural dynamics.

This paper reports a new control strategy to improve sharing of unbalanced currents in islanded LV microgrids. This technique provides fast and effective sharing of positive-, negative- and zero-sequence currents, and is the first example of zero-sequence current sharing in the literature. The controllers are designed in the stationary frame. The control structure consists of four loops; 1)~the current controller; 2)~the voltage controller; 3)~the droop controller and the 4)~negative and zero sequence current controllers. The output current is considered unknown for the controller and is added to the control system as a disturbance. The proposed controller features a high gain in fundamental and harmonic frequencies, hence a good voltage quality is obtained in the presence of unbalanced and nonlinear loads. To this aim, a proportional-resonant (PR) controller is adopted as the current controller. By using a multi-resonant controller as current controller, a unified control structure is obtained which is suitable for both grid-connected and islanded modes. The voltage controller is designed using a resonant controller so that the voltage can have low VUF and THD in the presence of unbalanced and nonlinear loads. Furthermore, in this paper droop method is applied to the control structure to share real and reactive powers. Simulation studies show that the conventional droop method cannot share the oscillatory part of the output power that is due to the presence of unbalanced loads in the microgrid. This paper relies on using zero and negative sequence virtual impedance controller to share the oscillatory part of output power. By using zero-sequence virtual impedance controller (ZSVIC) and negative-sequence virtual impedance controller (NSVIC), the zero and negative sequence currents in the microgrid are controlled and shared effectively. By compensating zero- and negative-sequence currents locally, the flow of these currents in the microgrid is minimized, and the overall power quality of the islanded LV microgrid is improved.

The crack geometry and associated strain field around Berkovich and Vickers indents on silicon have been studied by X-ray diffraction imaging and micro-Raman spectroscopy scanning. The techniques are complementary, the Raman data coming from within a few micrometers of the indentation, whereas the X-ray image probes the strain field at a distance of typically tens of micrometers. For example, Raman data provides an explanation for the central contrast feature in the X-ray images of an indent. Strain relaxation from breakout and high temperature annealing are examined and it is demonstrated that millimeter length cracks, similar to those produced by mechanical damage from misaligned handling tools, can be generated in a controlled fashion by indentation within 75 micrometers of the bevel edge of 200mm diameter wafers.