Most of the pore-scale imaging and simulations of non-Newtonian fluid are based on the simplifying geometry of network modeling and overlook the fluid rheology and heat transfer. In the present paper, we developed a non-isothermal and non-Newtonian numerical model of the flow properties at pore-scale by direct simulation of the 3D micro-CT images using a Finite Volume Method (FVM). The numerical model is based on the resolution of the momentum and energy conservation equations. Owing to an adaptive meshing technique and appropriate boundary conditions, rock permeability and mobility are accurately computed. A temperature and concentration-dependent power-law viscosity model in line with the experimental measurement of the fluid rheology is adopted. The model is first applied at isothermal condition to 2 benchmark samples, namely Fontainebleau sandstone and Grosmont carbonate, and is found to be in good agreement with the Lattice Boltzmann method (LBM). Finally, at non-isothermal conditions, an effective mobility is introduced that enables to perform a numerical sensitivity study to fluid rheology, heat transfer, and operating conditions. While the mobility seems to evolve linearly with polymer concentration, the effect of the temperature seems negligible by comparison. However, a sharp contrast is found between carbonate and sandstone under the effect of a constant temperature gradient. Besides concerning the flow index and consistency factor, a good master curve is derived when normalizing the mobility for both the carbonate and the sandstone.

The purpose of this work is to optimize angular extrusion for sever plastic deformation of tubular specimens. A finite element model (FEM) was built in Deform-3D^® for three extrusion dies and analyzed. The dies were ECAP (135°), TCAP with external groove of 90° (denoted as TCAP-e) and TCAP with internal groove of 90° (denoted as TCAP-i). The analysis for process parameters (such as coefficient of friction-μ, die angles-ѱ and φ, temperature - T, and radius ratio-R) showed that TCAP-i was the optimal die in processing Al6063 tubes based on strain and load distribution of the model. The TCAP-i die model was further optimized for different parameters namely die angles, coefficient of friction, deformation ratio and temperature. The results showed that at constant process temperature of 25 °C, the optimal TCAP-i has the following parameters: φ₂=80⁰, Ѱ₁=30⁰, Ѱ₂=80⁰, Ѱ₃=30⁰, μ =0.4 and R =1.5.

As the smallest member of the fullerene family, C20 is yet to be discovered in planetary nebulae. In this work, we present a quantum chemical study via density functional theory (DFT) on the ionization tolerance of this molecule in the space environment. Considering that the ionization and excitation phenomena play key roles in alerting the lifetime of a molecule, we examined both ground and excited electronic states potential energy surfaces (PES) of C20 and its cations C20q+. Our theoretical results indicate that the C20 cage tolerates a positive charge as high as 13+ via characterizing local minimum geometries on both mentioned electronic states. We also explored theoretically and systematically, scenarios in which the electronic structure of neutral C20 is excited to very high spin multiplicity (beyond triplet state) and local minimum molecular geometries with cage structure are well characterized. We anticipate that such structural resistance to excitation and ionization deliver a prolonged lifetime necessary for the spectroscopic detection of this interesting molecule and its cations in space and potentially in planetary nebulea (PN).

Influenced by the pluralistic and open-minded cultural ideologies of shamanism, the rulers of the Mongol Yuan Dynasty emphasized the implementation of religious government policies with an emphasis on coexistence, adaptability, and pragmatism. The Mongol ruling elite formed alliances with religious factions in various regions and worked closely with local spiritual leaders. During the era of the Great Mongol State, Kublai Khan valued the wealth of the Han Chinese territories. To maintain the order of Mongol Yuan rule in northern China, he used Han Chinese Buddhism and other religious forces to balance and suppress Quanzhen Dao. As a result, Chinese Buddhism became increasingly politically influential in Mongolia. Using their religious identity and talent, Chinese Buddhist monks became active in Mongolia to regulate the political activities of the Han Chinese religious forces. This led to a shift in the religious landscape of northern China during the transition from the Jin to Yuan dynasties.

Grape pomace (GP) is considered a natural source of bioactive compounds. To improve the ex-tractability of bioactive compounds, in this work GP was biologically treated for 15 days with the white-rot fungus Trametes versicolor in laboratory jars and a tray bioreactor under solid-state fermentation (SSF) conditions. During SSF, the activity of lignolytic (laccase, manganese peroxi-dase) and hydrolytic (xylanase, cellulase, β-glucosidase and invertase) enzymes was measured, with the activity of laccase (2.66 U/gdb in jars and 0.96 U/gdb in the bioreactor) and xylanase (346.04 U/gdb in jars and 200.65 U/gdb in the bioreactor) being the highest. The effect of the com-plex enzyme system was reflected in the changes in the chemical composition of GP with in-creasing ash, crude protein and free fat content: 28%, 10% and 17% in the laboratory jars and 29%, 11% and 7% in the bioreactor, respectively. In addition, the biological treatment had a positive effect on the extractability of 13 individual phenolic compounds. Therefore, the applied SSF technique represents an effective strategy to improve the profile of phenolic compounds and the nutritional composition of GP, promoting their valorization and opening the door for potential application in the food industry and other sectors.

This study reveals the essential load-bearing characteristics of the steel-concrete composite floor system under fire conditions applying structural stressing state theory. Firstly, the strain data in the entire process of the fire test are modeled as state variables which can present the slab’s stressing state evolution characteristics; Then, the state variables are used to build the stressing state mode and the parameter characterizing the mode. Further, the Mann-Kendall criterion is adopted to detect the leap points in the evolution curves of the characteristic parameters during the entire fire exposure process. Also, the evolution curves of the stressing state modes are investigated to verify the leap profiles around the leap/characteristic points; Finally, the detected leap points are defined as the failure starting points and elastoplastic branching points, which is unseen in the past researches focusing on the failure endpoint defined at the ultimate load-bearing state of the composite floor system. The failure starting point and the elastoplastic branching point are the embodiment of natural law from quantitative change to quality change of a system rather than an empirical and statistical judgment. Hence, both characteristic points avoidably exist in the strain data of the composite floor system undergoing the fire process, which can be revealed through the proper modeling methods and update the existing theories and methods on structural analysis and design in fire.

Frass generated during the production of black soldier fly larvae is taking the interest of scientists and horticultural producers because it is a material from the biotransformation of organic waste, it has several nutrients that can be used by plants, and its recent focus on its biostimulant capacity. The thermal-composting process is a stabilization that improves physical and chemical properties of treated wastes, allowing better performance in plants compared to its fresh state. In this research, thermocomposted frass was evaluated as a germination substrate for kale seeds (Brassica olerasea). To achieve this, it was evaluated the phytotoxicity in different concentrations on the seeds, and seedlings were grown in a germination substrates mixed with 20, 40, 60, 80 and 100% of frass. The treatment with 20% frass showed the highest values of seedling height, stem diameter, number of leaves, length, and width of first true leaf and length and width of cotyledons, reduced the content of phenols and tannins antioxidants but the content of flavonoids increased compared to the control and the rest of mixtures.

We consider a constrained optimal control problem and an extension of it, in which the set of strict-sense trajectories is enlarged. Extension is a common procedure in optimal control, used to derive necessary and sufficient optimality conditions for the original problem from the extended one, which usually admits a minimizer and has a more regular structure. However, this procedure fails if the two problems have different infima. It is therefore relevant to identify such situations. Following on from earlier work by Warga but adopting perturbation techniques developed in non-smooth analysis, we investigate the relation between the occurrence of an infimum gap and abnormality of necessary conditions. For a notion of local minimizer based on control distance and an extension including the impulsive one, we prove that (i) a local extended minimizer which is not a local minimizer of the original problem and (ii) a local strict-sense minimizer which is not a local minimizer of the extended problem, both satisfy the extended maximum principle in abnormal form. The main novelty is result (ii), as until now it had only been shown that a strict-sense minimizer which is not an extended minimizer is abnormal for an `averaged version’ of the maximum principle.

An exposition is undertaken to reveal the significant impact of the time-dependent root parameter, on the stability of Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary queueing system. This opens new grounds to stability analysis of non-stationary queueing systems. Potential PSFFA applications of IoT are highlighted.

Rising demand and urbanization have led to the global increase and intensification of livestock production. Intensive production has harmful effects on the environment, public health (due to the emergence of zoonotic diseases), and animal welfare. In order to better understand how livestock production intensifies as countries develop and incomes rise, we examine the relationship between income per capita and intensification of poultry and cattle, using the states of India as a study region. We also replicate this analysis at the district level to test whether the relationship holds at different spatial scales. We identify outlying states and districts to see if there are policies that can keep agriculture production largely extensive, even as economic growth occurs. The results support the relationship of income being positively correlated with the proportion of livestock in intensive conditions. However, there are notable outlier states which have grown wealthy while still maintaining largely extensive production, indicating that there may be some cases where economic growth can occur without intensification.

This paper focuses on leveraging a cutting-edge 3D state-space model for a holistic eco-friendly assessment in petrochemical operations. - By applying the ecological carrying capacity theory and the three-dimensional state-space model, this research aims to unleash the next frontier of sustainability in the petrochemical industry. - The proposed methodology will enable advanced and comprehensive eco efficiency evaluation in petrochemical operations. - Through the integration of the ecological carrying capacity theory and advanced modeling techniques, this research seeks to revolutionize sustainability assessments in the petrochemical sector. - The utilization of the cutting-edge 3D state-space model will provide a more advanced and accurate understanding of eco-friendly practices in petrochemical operations. This research presents a unique approach distinct from existing literature, which primarily examines business eco efficiency from behavioral motivation and strategic perspectives. In contrast, this paper introduces a novel three-dimensional state-space model to evaluate the ecological efficiency of petrochemical operations. By combining the ecological carrying index and state space, this model represents the ecological impact of petrochemical operations in a three-dimensional geometric space. It considers petrochemical operations as a significant factor exerting pressure on natural resources and the natural environment. In this three-dimensional state-space model, the three axes represent different dimensions of petrochemical operations. The first axis represents the economic status, which quantitatively describes the financial aspects of the operation. The second axis represents the utilization of resources, capturing the extent to which resources are consumed in the operation. The third axis focuses on the impact of the operation on the environment, allowing for a quantitative assessment of its ecological footprint. By incorporating these dimensions, the model aims to provide a comprehensive and quantitative description of the economic activities of petrochemical operations and their interactions with resources and the environment.The primary focus of this research is to apply the three-dimensional state-space model to calculate the ecological carrying capacity of petrochemical operations. By doing so, it aims to verify the feasibility and applicability of the model in determining the ecological efficiency of these operations. The research also aims to provide theoretical tools that can assist operations in making more informed ecological efficiency judgments. By utilizing this model, petrochemical operations will have a quantitative framework to assess and improve their environmental impact, thus fostering more sustainable practices. The findings of this research demonstrate that the implementation of this method can effectively identify issues related to resources, economy, and environment throughout the development of petrochemical operations. By identifying these problems, it provides managers with a solid foundation for making strategic decisions that promote sustainable development. With this valuable information at their disposal, managers can proactively address challenges, optimize resource utilization, and minimize environmental impacts, thus steering the petrochemical operations towards a more sustainable and responsible path.

Lithium-ion batteries are key elements in the development of electrical energy storage solutions. However, due to cycling, environmental and operating conditions, battery capacity tends to degrade over time. Capacity fade is a common indicator of battery state of health (SOH) because it is an indication of how capacity has been degraded. However, battery capacity cannot be measured directly, so there is an urgent need to develop methods for estimating battery capacity in real time. By analyzing the historical data of a battery in detail, it is possible to predict the future state of the battery and forecast its remaining useful life. This paper develops a real-time, simple and fast method to estimate the cycle capacity of a battery during the charge cycle using only data from a short period of each charge cycle. This proposal is attractive because it does not require data from the entire charge period, since batteries are rarely charged from zero to full. The proposed method allows simultaneous and accurate real-time prediction of the health and remaining useful life of the battery over its lifetime. The accuracy of the proposed method has been tested using experimental data from several lithium-ion batteries with different cathode chemistries under various test conditions.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

Recent advancements in the study of the protein complex photosystem II have clarified the sequence of events leading to the formation of oxygen during the S3->S4->S0 tran-sition, wherein the inorganic Mn4Ca(µ-O)6(OHx)4 cluster finishes photo-catalyzing the water splitting reaction (Greife et al, Nature 2023, 617, 623-628; Bhowmick et al, Nature 2023, 617, 629-636) . During this final step a tyrosine radical (TyrZ), stable for a couple of milliseconds, oxidizes a cluster bound oxygen while the hydrogen bonding patterns of nearby waters shift a proton away. A treatment of this redox reaction within the context of accepted transition state theories predicts rate constants that are significantly higher than experimentally recovered values (10^12s^-1 versus 10^3s^-1). In an effort to understand this disparity, temperature dependent experiments have revealed large entropic con-tributions to the rates with only a moderate energy of activation. We suggest that the entropic source may be related to the observed proton rearrangements, and further possible near isoenergetic variations in the nearby extended h-bonding network de-laying the realization of an ‘ideal’ transition state. In the following we explore this re-lation in the context of Eyring’s transition state theory and Marcus’ electron transfer theory, and evaluate their compatibility with the experimental evidence.

In this paper the application of the solid-state cooling based on barocaloric effect in the cold food supply chain is investigated. Barocaloric solid-state technology is applied to the final chain links of the cold food supply chain, regarding the steps of retail and domestic conservation. In this context a barocaloric cooler with regard to food needing to be kept at 5°C (273 K), in order to operate with a promising cooling technology that result energy efficient and environmentally friendly. The categories of food interested in the investigation are meets and fresh food products like soft cheese, yogurt, milk. The energy performances of the barocaloric system have been carried out and compared with a commercial vapor compression refrigerator of a similar size, both operating with R600a under the same working conditions. Basing on the following consideration one can conclude that barocaloric cooling is a favourable technology to be employed in the last link chains of the cold food supply chain if the system operates in ABR cycle at frequencies between 1.25 and 1.50 Hz with a regenerator made of acetoxy silicone rubber as solid-state refrigerant and 50%EG-50%water mixture as heat transfer fluid flowing at the optimal velocity of 0.15 m s-1 that guarantees an appropriate trade-off between the temperature span, the cooling power and the coefficient of performances. Under these conditions the barocaloric system overperforms the domestic vapor compression cooler operating with R600a.

The results of measuring the capacity of a thin-film solid-state lithium-ion battery (SSLIB) Ti|Si@O@Al|LiPON|LiCoO₂|Ti at different charge currents are reported. It is shown that the dependence of the capacity on the current density follows the Peukert's law, which is characterized by a low value of the Peukert’s exponent in the region of low currents and a high value of the exponent in the region of high currents. A capacity model for a SSLIB based on the balance of diffusion and migration currents is proposed and the dependence of the capacity on the charge current is derived. The obtained dependence is well approximated by Peukert's law with an exponent of 1.39, which is intermediate between the exponents for lithium-ion batteries with liquid electrolyte and SSLIBs.

Childhood malnutrition is one of the most persistent public health problems throughout developing countries including Nigeria. This study focused on the evaluation of complementary food produced by solid-state fermentation of Fonio and Soybean using Rhizopus oligosporus (2710) and Orange-fleshed sweet potatoes (OFSP) using Lactobacillus planterum, (B-41621). Solid state fermentation (SSF) was carried out by inoculating Fonio and Soybean with spore suspension (1×10⁶spores/ml) of Rhizopus oligosporus (2710) and OFSP with spore suspension (1×10⁶spores/ml) of Lactobacillus planterum (B-41621). The samples were blended in the following ratios: Fonio and Soybean 100: 100 (AS), fonio/soybean and OFSP 50: 50(ASO), and compared with a commercial infant formula which served as the control (CTRL). Quality characteristics of the samples were evaluated. Results showed that moisture, crude protein, fibre, ash content, beta carotene and titratable acidity increased significantly (p<0.05) as fermentation progressed. The iron content ranged from 6.57–8.41mg/100g while the beta carotene content ranged from 15.80 –17.35mg/100g. Viscosity ranged from 8200 –15400cP, while that of swelling capacity ranged from 2.25-3.41(g/g). In sensory scores, there were no significant (p>0.05) difference between the average mean scores of the samples. SSF improved the nutritional content and flavour of the developed complementary food which is needed for infant growth and development.

Hematological and biochemical reference values in sickle cell disease (SCD) are crucial for patient management and evaluation of interventions. This study was conducted at Muhimbili National Hospital (MNH) in Dar es Salaam, to establish laboratory reference ranges in SCD at steady-state. Patients were grouped into five age groups with respects to their sex. Aggregate functions were used to handle repeated measures within the indi-vidual level in each age group. A nonparametric approach was used to smooth the curves and a parametric approach was used to determine SCD normal ranges. Comparison between males and females and against the general population was documented. Data from 4,422 patients collected from 2004-2015 were analyzed. The majority of the patients (35.41%) were children aged between 5-11 years. There were no significant differences (p≥0.05) in mean corpuscular hemoglobin concentration (MCHC), lymphocytes, basophils and bilirubin direct observed between males and females. Significant differences (p<0.05) were observed in all selected parameters across age groups except neutrophils and MCHC in adults, as well as platelets and alkaline phosphatase in infants when SCD estimates were compared to the general population. Laboratory reference ranges in SCD at steady-state were different from those of the general population and varied with sex and age. The established reference ranges for SCD at steady-state will be a helpful in the management and monitoring of the progress of SCD.

AbstractIn the evolving modern era of neuromodulation for movement disorders in adults and children, much progress has been made recently characterizing the human motor network (MN) with potentially important treatment implications. Herein is a focused review of relevant resting state fMRI functional and effective connectivity of the human motor network across the lifespan in health and disease. The goal is to examine how the transition from static functional to dynamic effective connectivity may be especially informative of network-targeted movement disorder therapies, with hopeful implications for children.Impact StatementWhile functional connectivity has elucidated much MN properties with relation to age, disease, and behavior, effective connectivity has been shown to be useful in MN-informed therapies in adults. Thus, effective connectivity may have potential to impact childhood movement disorder therapies, given the lower to no patient demand.

Three low band gap copolymers based on isoindigo acceptor units were designed and successfully synthesized by direct arylation polycondensation method. Two of them were benzodithiophene(BDT)-isoindigo copolymers (PBDTI-OD and PBDTI-DT) with 2-octlydodecyl(OD) and 2-decyltetradecyl (DT) substituted isoindigo units, respectively. Thiophene donor and DT-substituted isoindigo acceptor units were copolymerized to synthesize PTI-DT. The copolymers have broad absorption range that extends to over 760 nm with a band gap ~ .5 eV. The photophysical property studies showed the BDT based copolymers have non-polar ground states. Their emission exhibited the population of intramolecular charge transfer (ICT) state in polar solvents and tightly bound excitonic state in non-polar solvents due to self-aggregation. On the contrary, the emission from the thiophene based copolymers was only from the tightly bound excitonic state. The thermal decomposition temperature of the copolymers was above 380 oC. The X-ray diffraction pattern of the three copolymers showed a halo due pi-pi stacking. A second sharper peak was observed in the BDT-based copolymer with longer side chain on the isoindigo unit (PBDTI-DT) and the thiophene based copolymers with PTI-DT exhibiting a better structural order.

The cyclic lipopeptide produced from Bacillus pumilus strain HY1 was isolated from Korean soybean sauce. The chemical structures of the surfactin isomers were analyzed using matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF MS) and electrospray ionization tandem mass spectrometry (ESI-MS/MS). The five potential surfactin isoforms were detected with protonated masses of m/z 994.7, 1,008.7, 1022.7, 1036.7, and 1,050.7 and different structures in combination with Na+, K+, and Ca2+ ions. ESI-MS/MS analysis revealed that the isolated surfactin possessed the precise amino acid sequence LLVDLL and hydroxyl fatty acids with 12 to 16 carbons. The surfactin content during cheonggukjang fermentation increased from 0.3 to 51.2 mg/kg over 60 h of fermentation. The surfactin extraction of cheonggukjang inhibited the growth of two cancer cell lines. The growth of both MCF-7 and Caco-2 cells was strongly inhibited with 100 μg/μL surfactin. These results suggest that surfactins produced from strain HY1 have anticancer properties.

Biophoton emission has been experimented for decades. The photo-genic origin of biophoton has also been attributed to the oxidative stress or free radical production. However, there are considerable gaps in quantitative understanding of biophoton emission. In this work, I propose an analytical hypothesis for interpreting a few patterns of steady-state biophoton emission of human, including the dependency on age, the diurnal variation, and the geometric asymmetry associated with serious asymmetrical pathological conditions. The hypothesis is based on an alternative form of energy state, termed vivo-nergy, which is associated with only metabolically active organisms that are also under neuronal control. The hypothesis projects a decrease of the vivo-nergy in human during growth beyond puberty. The hypothesis also proposes a modification of the vivo-nergy by the phases of systematic or homeostatic physiology. The hypothesis further postulates that the deviation of the physiology-modified vivo-nergy from the pre-puberty level is deteriorated by acquired organ-specific pathological conditions. A temporal differential change of vivo-nergy is hypothesized to proportionally modulate oxidative stress that functions as the physical source of biophoton emission. The resulted steady-state diffusion of the photon emitted from a photo-genic source in a human geometry simplified as a homogeneous spherical domain is modeled by photon diffusion principles incorporating an extrapolated zero-boundary condition. The age and systematic physiology combined determines the intensity of the centered physiological steady-state photo-genic source. An acquired pathology sets both the intensity and the off-center position of the pathological steady-state photo-genic source. When the age-commemorated, physiology-commanded, and pathology-controlled modifications of the steady-state photo-genetic sources are implemented in the photon diffusion model, the photon fluence rate at the surface of the human-representing spherical domain reveals the patterns on age, the temporal variation corresponding to systematic physiology, and the geometric asymmetry associated with significant asymmetric pathological condition as reported for spontaneous biophoton emission. The hypothesis, as it provides conveniences for quantitative estimation of biophoton emission patterns, will be extended in future works towards interpreting the temporal characteristics of biophoton emission under stimulation.

This study was conducted to evaluate the feasibility of applying a two-step biological treatment process, solid-state anaerobic digestion (SSAD) and black soldier fly larvae (BSFL) composting, for treating dairy cattle manure. Biogas from SSAD of dairy cattle manure, and the digestate of SSAD was fed to BSFL. In turn, BSFL can be fed to animals as a protein supplement. Adjustment of pH and 30% inoculation ratio (IR₃₀) during SSAD produced the highest theoretical methane yield, 626.1±28.7 L CH₄/kg VS_des, with an ultimate methane yield of 96.81±2.0 L CH₄/kg VS_load. For BSFL composting, the groups with a feeding rate of 75 and 100 mg/day/larvae had the highest body weight change, which was 969.6±28.4 and 984.1±177.6%, respectively. The combination process of SSAD and BSFL composting increases the incentive for dairy cattle manure treatment enabled higher waste removal efficiency, and produced more valuable products.

The penetration of modern supermarkets is believed to be the cause of the declining role of traditional markets and street vendors in Indonesia. But the competition between state-promoted markets and traditional markets is rarely discussed. This investigation focuses on traditional markets as social institutions, which continuously have developed a variety of strategies in order to remain competitive in the midst of intense rivalry. Firstly, we will outline a theoretical understanding of the traditional markets positioning along the concepts of flexibility and market devices. Secondly, we empirically reflect the strategies of four traditional vegetable markets in the District of Malang, East Java Province, as case studies. We show that the traditional markets build flexibility without governmental support by: (1) specifying commodities, (2) segmenting customers, (3) managing the load time, (4) modifying transportation to operate more efficiently, and (5) minimizing transaction costs by leveraging social capital. We argue that traditional vegetable markets institutionally reduce the potential of transaction costs to be competitive and avoid problems of coordination by building social capital through networks. All in all, market institutions supported by market devices are flexibly capable of adapting to the pressures of both selfishness among actors and competition with other markets.

We review a theory that predicts the onset of thermalization in a quantum mechanical coupled non-linear oscillator system, which models the vibrational degrees of freedom of a molecule. A system of N non-linear oscillators perturbed by cubic anharmonic interactions exhibits a many-body localization (MBL) transition in the vibrational state space (VSS) of the molecule. This transition can occur at rather high energy in a sizable molecule because the density of states coupled by cubic anharmonic terms scales as ~ N3, in marked contrast to the total density of states, which scales as exp(aN), where a is a constant. The emergence of a MBL transition in the VSS is seen by analysis of a random matrix ensemble that captures the locality of coupling in the VSS, referred to as local random matrix theory (LRMT). Upon introducing higher order anharmonicity, the location of the MBL transition of even a sizable molecule, such as an organic molecule with tens of atoms, still lies at an energy that may exceed the energy to surmount a barrier to reaction, such as a barrier to conformational change. Illustrative calculations are provided, and some recent work on the influence of thermalization on thermal conduction in molecular junctions is also discussed.

Protein-DNA interactions are critical for the successful functioning of all natural systems. The key role in these interactions is played by processes of protein search for specific sites on DNA. Although it has been studied for many years, only recently microscopic aspects of these processes became more clear. In this work, we present a review on current theoretical understanding of the molecular mechanisms of the protein target search. A comprehensive discrete-state stochastic method to explain the dynamics of the protein search phenomena is introduced and explained. Our theoretical approach utilizes a first-passage analysis and it takes into account the most relevant physical-chemical processes. It is able to describe many fascinating features of the protein search, including unusually high effective association rates, high selectivity and specificity, and the robustness in the presence of crowders and sequence heterogeneity.

Linear state estimation (SE) formulation under a rectangular coordinate system has been proved to be applicable for real-time distribution network management. Micro phasor measurements’ model can be accommodated into this kind of SE easily. However, voltage magnitude, active power and reactive power measurements are transformed to linear measurements with large node voltage error. To cope with this issue, a linear state estimation under a polar coordinate system is adopted at the first stage to obtain accurate enough complex node voltage, and then nonlinear measurements are transformed to be linear with complex node voltage. At the second stage, linear SE under a rectangular coordinate system can be adopted to satisfy more strict network constraints. The proposed two-stage linear SE is validated on balanced 14, 33, 70,84, 119, 135 nodes network and IEEE 13, 34, 37,123 unbalanced test feeders.

State Forest Management Organizations (SFMOs) play a crucial role in the European forest sector, managing almost half the forests in the region. SFMOs are often managed for timber production only whereas, being publicly owned, they should play an important role in providing a vast range of public goods (e.g. soil protection, biodiversity conservation). Their management goals depend on the history and current conditions of the forest sector at a national level, as well as different challenges and the potential for development. Although there is a lack of knowledge about the current performance of SFMOs, there have been recent changes to their management goals and practices in response to the new demands expressed by society (e.g. transparency, social inclusion). The main purpose of this study is to analyse the current situation of SFMOs by clustering them according to indicators that reflect three pillars of the common understanding of sustainable forest management (SFM) concept. With the help of Principal Component Analysis (PCA), we grouped countries according to common characteristics of the forest sector at the national level. Results show three main clusters of SFMOs in Europe. The first cluster has rather small but commercially-oriented forestry unit together with other business activities and a strong focus on public services. The second sees itself as the protector of public interest, rather than commercially-oriented organisations. The third is mainly profit-seeking. The existence of diverse SFMO clusters shows the possibility of different approaches for SFM with a focus on different goals (e.g. profit gaining, public service delivery).

Accelerating, exact, explicit and simple solutions of relativistic hydrodynamics allow for a simple and natural description of highly relativistic p+p collisions. These solutions yield a finite rapidity distribution, thus they lead to an advanced estimate of the initial energy density of high energy collisions. We show that such an advanced estimate yields an initial energy density in $\sqrt{s}=7$ and 8 TeV p+p collisions at LHC around or above the critical energy density from lattice QCD, and a corresponding initial temperature above the critical temperature from QCD and the Hagedorn temperature. This suggests that the collision energy of the LHC corresponds to a large enough initial energy density to create a non-hadronic perfect fluid even in pp collisions. %We also show, that several times the %critical energy density may have been reached in high multiplicity events, hinting at a non-hadronic medium created in %high multiplicity $\sqrt{s}=7$ and 8 TeV p+p collisions.

Owing to the risk of atypical femoral fractures, total hip arthroplasty presents unique challenges for patients with ipsilateral osteoarthritis and localized periosteal thickening in the femoral subtrochanteric region. Stem length selection is critical for minimizing stress concentration in the thickened cortex to avoid such fractures. Herein, we report the case of a 78-year-old woman with ipsilateral hip osteoarthritis and localized subtrochanteric periosteal thickening. Preoperative planning included finite element analysis to assess stress distribution across various stem lengths. Simulation aimed to determine the optimal stem length to span the cortical thickening and reduce the risk of postoperative complications. The results of finite element analysis indicated that a stem length of &gt;150 mm was required to effectively reduce the stress at the site of cortical thickening. A 175-mm stem was selected for total hip arthroplasty, which provided a favorable stress distribution and avoided the risk of stress concentration. Therefore, in cases of ipsilateral osteoarthritis with localized subtrochanteric periosteal thickening, finite element analysis can be valuable for preoperative planning to determine the optimal stem length, thereby reducing the risk of atypical femoral fractures. Further studies with multiple cases are recommended to validate these findings and improve surgical outcomes.

The construction of tall buildings generates a high spatial and temporal concentration of greenhouse gas (GHG) emissions. Research studies have shown that as building height increases, more resources per floor area are required to withstand the increasing effects of lateral loads (wind and earthquake). This has major implications for the environmental performance of tall buildings since the Embodied GHG Emissions (EGHGE) of structural systems tend to represent the greatest portion of the life cycle GHG emissions of tall buildings. This study presents a data driven-based approach for decarbonization of tall buildings and evaluates the significant impact of material types (concrete, steel, and timber), concrete strength, and structural systems relative to a building's height on the EGHGE associated with tall buildings. In mitigating the effects of climate change, this research implements machine learning (ML) algorithms as an early-stage design tool to facilitate the choice of materials, and structural systems for tall buildings. This work considers a wide range of high-rise buildings with four different types of lateral structural systems (Braced-Frame system, Outrigger-Belt system, Shear Wall system, and Tubular system), four different types of construction materials (concrete, steel, hybrid, and timber), varying heights (ranging from 10 to 100 stories), and various concrete materials with different compressive strength ranging from 32 to 90 MPa. Data gathered from more than 100 existing tall building projects along with the data obtained from finite element analysis of 120 high-rise buildings models were utilized to train various ML regression algorithms: Decision Tree, Support Vector Machine, Polynomial Regression, and Elastic-Net Regularized Regression. The performance of ML models was carefully assessed, and the best prediction model was selected to estimate the total amount of CO2 emissions for high-rise buildings. Results indicate that hybrid structures with the Out-Rigger-Belt system exhibit the lowest carbon emission (110 kg/m2) compared to other structural types and systems.

Corrugated boards are used for packaging because of their high strength-to-weight ratio, recyclability, and biodegradability. They have an orthotropic sandwich structure with unique characteristics for each direction owing to their flute shape. In this study, the bending behavior was qualitatively analyzed for various variables through an FE-based simulation, and the possibility of an alternative test method for the four-point bending test on a corrugated board was examined through a similarity analysis with the experimental results. The cross-machine direction (CD) bending stiffness through finite element analysis (FEA) simulation was closely related to the thickness of the corrugated board. In AB-flute-double-wall (AB/F-DW), the difference in CD bending stiffness based on the bending direction was approximately 17.2% in the FEA simulation and approximately 10.5% in the experiment. However, the differences in the bending behavior (bending force vs. deflection plot) and bending stiffness based on the phase shift between the two flutes constituting BB-flute-double-wall (BB/F-DW) were insignificant. Overall, the CD bending behavior of the corrugated board was simulated relatively well through FEA simulation. However, it was impossible to simulate the machine-direction (MD) bending behavior through FE-based simulation because of a decrease in convergence and a large error caused by the variability of the contact condition of the modeled test specimen with a non-uniform MD cross-section.

The finite-time turnpike property describes the situation in an optimal control problem where an optimal trajectory reaches the desired state before the end of the time interval and remains there. We consider a machine learning problem with a neural ordinary differential equation that can be seen as a homogenization of a deep ResNet. We show that with appropriate scaling of the quadratic control cost and the non-smooth tracking term the optimal control problem has the finite-time turnpike property, that is the desired state is reached in the interior of the time interval and the optimal state remains there until the terminal time $T$. This property is useful to achieve a compromise between the depth of the network and the size of the optimal system parameters which we hope will be useful to determine optimal depths for neural network architectures in the future.

To improve the current density distribution and electromagnetic performance of air-core inductors, a structural optimization method combining BP neural network and genetic algorithm was proposed for the study of axial and radial spiral multi-winding inductors. The Monte Carlo method was used to extract the structural size samples of the inductors, and the training dataset was obtained through finite element calculation of electromagnetic fields. Based on BP neural networks, nonlinear mapping models between the inductance value, volumetric inductance density, current distribution non-uniformity coefficient, and inductor structural parameters were constructed. The sensitivity analysis of the inductor inductance value affected by structural parameters was conducted through the Sobol index calculation. Using the current distribution non-uniformity coefficient as the fitness function and the volumetric inductance density as the constraint condition, the genetic algorithm was applied to optimize the structural parameters of the inductor globally. The optimization results were verified through finite element comparison. The results show that, under the requirement of satisfying the volumetric inductance density, the current distribution non-uniformity coefficient of AHI type inductor was reduced by 4.57% compared with the best sample in the sampling, while that of RHI type inductor was reduced by 5.33%, demonstrating the practicality of the BP-GA joint algorithm in the structural optimization design of inductors.

Permeability is a fundamental property of porous media, especially when studying resin transfer within a dense fibrous medium to manufacture composite materials. When the measurement of permeability tensor of composite reinforcements is difficult and time consuming, especially in thick, heterogeneous fibrous structures, a numerical approach based on the calculation of the tensor components on a 3D image of the material can be very advantageous. A new finite element based method proposed in this study allows solving very high-dimensional flow problems while limiting the biases associated with boundary conditions and the small size of the numerical samples addressed. The method is validated against academic test cases and against the results of a recent permeability benchmark exercise. The results emphasize that for heterogeneous and anisotropic microstructures, it is important to perform calculations on large samples using boundary conditions that do not suppress the transverse flows that occur when flow is forced out of the principal directions. Since these are not necessarily known in complex media, the permeability determination method must not introduce bias by generating non-physical flows.

Accurate cloud quantification is essential in climate change research. In this work, we construct an automated computer vision framework by synergistically incorporating deep neural networks and finite sector clustering to achieve robust whole sky image-based cloud classification, adaptive segmentation, and recognition under intricate illumination dynamics. A bespoke YOLOv8 architecture attains over 95% categorical precision across four archetypal cloud varieties curated from extensive annual observations (2020) at a Tibetan highland station. Tailor-made segmentation strategies adapted to distinct cloud configurations, allied with illumination-invariant image enhancement algorithms, effectively eliminate solar interference and substantially boost quantitative performance even in illumination-adverse analysis scenarios. Compared with the traditional threshold analysis method, the cloud quantification accuracy calculated within the framework of this paper is significantly improved. Collectively, the methodological innovations provide an advanced solution to markedly escalate cloud quantification precision levels imperative for climate change research, while offering a paradigm for cloud analytics transferable to various meteorological stations.

The paper delves into the critical issue of damage detection within the guy cable of a truss steel mast, a pivotal component in structural integrity. It introduces a model wherein damage manifests as a localized cross-section reduction in a single element of the cable. Employing Discrete Wavelet Transform (DWT), a pioneering methodology, the study scrutinizes the behavior of the affected elements through static structural analyses. Signal decomposition via the Mallat pyramid algorithm facilitates comprehensive examination. Static displacements at the connection point between the cable and the truss mast serve as the measured variables. Through systematic investigation, the paper evaluates the impact of damage size and location, external loading force, and cable tension force on the efficacy of the proposed approach. Utilizing data derived from Finite Element Method (FEM) computations for wavelet analysis the authors substantiate the findings with numerical examples, thus offering valuable insights into damage detection strategies for structural health monitoring and engineering applications.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

In order to further investigate the study of the effect of grouped stud effect on the force properties of stud connector, based on the premise that the correctness of the finite element simulation method in this paper, finite element modeling of grouped stud connectors was developed, the grouped stud effect and its sensitivity factors were analyzed, to validate the recommended formula for calculating the shear capacity of grouped stud connectors. Results show that the number of grouped stud rows and row spacing have a significant effect on the grouped stud effect, and the unevenness coefficient of grouped stud force Ⅰ is negatively correlated with the number of grouped stud rows as well as the grouped stud row spacing. For grouped stud connectors with commonly used concrete grades greater than C50 and height-to-diameter ratios greater than 4 in steel-concrete composite structural bridges, which is insensitive to changes in the concrete strength grades and the length of the studs. The direction of force transmission for the grouped stud changes with the change of loading angle, and the unevenness coefficient of force for the grouped stud will therefore be reduced. By comparing the results of the 62 existing groups of grouped stud connectors push-out tests, the mean value of the ratio of tested to calculated values is found to be 1.12, the variance is 0.023, the dispersion is small, it is shown that the recommended formula has a high degree of accuracy. The results of this paper can be used as a theoretical basis for the study of the shear stress performance of grouped stud connectors.

This paper studies the finite-time synchronization problem of fractional-order stochastic memristive bidirectional associative memory neural networks (MBAMNNs) with discontinuous jumps. A novel criterion for finite-time synchronization is obtained by utilizing the properties of quadratic fractional-order Gronwall inequality with time delay and the comparison principle. This criterion provides a new approach to analyze the finite-time synchronization problem of neural networks with stochasticity. Finally, numerical simulations are provided to demonstrate the effectiveness and superiority of the obtained results.

This study presents a comprehensive investigation of entropy generation during natural convection in a porous medium with Casson fluid. The governing equations, including the momentum, energy, and entropy balance equations, are solved numerically using finite element method. Through the analysis, various parameters affecting entropy generation are investigated, such as the Casson fluid parameter, Radiation, Prandtl number, and Rayleigh number. The results indicate that the Casson fluid parameter significantly influences the flow and heat transfer characteristics, while the Darcy number and Rayleigh number control the intensity of natural convection. Moreover, the Prandtl number determines the relative significance of heat transfer compared to viscous effects.

For enhancing the efficiency of cantilever casting the construction in the bridge, a novel rhombus traveling track of hanging basket was developed and optimized. The civil software titled Midas was applied to analyse the mechanical properties of the hanging basket with full load and control load. The strength and distortion of the walking mechanism were within the specified range when the maximum beam unit internal force of 149.69Mpa, which was less than the allowable stress of steel 175Mpa, and the anti-overturning safety factor of the hanging basket was 2.5 to meet the requirements. Through the comparative analysis of the key components and the finite element calculation, it was found that there was about 30% redundancy in the structure performance. Therefore, further optimization of each structure was carried out, and the front elevation of the main truss of 20° was achieved. It obtained the best performance in all aspects.

Nitrile butadiene rubber (NBR) and its various composites are extensively studied as matrix materials for oil-free lubricated mechanical friction surfaces. While numerous macroscopic friction experiments can compare the frictional performance of different NBR composites, the complex material preparation and low experimental efficiency pose challenges. Nanoscale molecular dynamics (MD) simulations can help develop materials with improved friction properties, but they cannot directly provide the friction coefficients of actual macroscopic friction surfaces. Therefore, it is important to integrate the advantages of macroscopic and nanoscale friction studies and perform a synergistic analysis to modify the friction properties of composite materials. In this study, a multi-scale approach is proposed to simulate the frictional characteristics of carbon nanotube (CNT)-reinforced NBR by combining the MD friction simulation， micromechanical bridging model, and macroscopic finite element analysis (FEA) methods. The results of the multi-scale friction simulation of copper (Cu)-CNT/NBR composites show that the addition of CNTs significantly improves the frictional properties of NBR, and the extent of the improvement is related to the mass fraction of CNTs. As the mass fraction of CNTs increases (0%, 1.25%, 2.5%, 5%), the coefficient of friction decreases from 0.50 to 0.38. The results are validated by ring-block friction experiments at the same scale as the simulations.

Functionally graded materials (FGM) have attracted considerable attention in the field of composite materials and rekindled interest in research on composite materials, due to their unique mechanical response achieved through material design and optimization. Compared to conventional composites, FGMs offer several advantages and exceptional properties, including improved deformation resistance, improved toughness, lightness properties, and excellent recoverability. This study focused on the production of functionally graded (FG) polymer materials by additive manufacturing (AM) method. FG structures were produced by the Fused Deposition Modeling (FDM) method using Acrylonitrile benzidine styrene (ABS) and Polylactic acid (PLA) materials and tensile tests were performed according to ASTM D638. The effects of different layer thicknesses, volume ratios, and total thicknesses on mechanical behavior were investigated. In addition, tensile tests were carried out by producing single-layer samples at certain volume ratios to create a numerical model with the Finite element method to verify the experimental data. As a result of this study, it is presented that the FG structure produced with FDM improves mechanical behavior.

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

In order to study the movement characteristics of fuel in the fuel tank during aircraft maneuvering, this paper conducts numerical simulations of a typical wing fuel tank using the finite point set method based on certain boundary conditions and excitation. The results show that the finite point set method can capture the complex phenomena of fuel free surface fluctuations, surging, rolling and breaking, as well as the change in center of gravity caused by fuel movement. Under aircraft acceleration and pitch angle excitation, fuel will generate sustained impact pressure on the fuel tank wall. The velocity attenuation of fuel flowing through the baffle communication hole is fast, and the flow resistance and energy dissipation of the communication hole buffer the impact of fuel on the fuel tank wall.

In this paper, we present the investigation results of radiation-induced effects in metal-oxide-semiconductor (MOS) doped with moderate amounts of Zinc Oxide (ZnO) as a potential candidate for space-borne application. The samples were fabricated via the sputtering method at a working pressure of 3mTorr and a deposition temperature of 300oC. The ZnO samples were exposed to 1.25-MeV gamma-ray utilizing Co60 source, and their electronic response was measured at ionizing doses ranging from 10 kGy to 300 kGy. A comparative work was performed through finite element method to simulate the electronic response of the PN junction diode due to ionizing radiation. The results indicate that the ideality factor of the MOS diode increases as the ionizing dose increases, rendering it unsuitable for use as a diode. The degradation of the electrical parameters was also simulated, showing the increase in hole concentration. These findings suggest that the ejection of electrons occurred, which agrees with the gamma radiation effects trend. Furthermore, as the intensity of radiation increases, the spatial charge that arises from the separation of hole-electron pairs results in a substantial reduction of the electric field in the central portion of the n-type region. These findings provide insights into the degradation of electrical parameters in MOS devices under gamma radiation and have implications for their use in space-borne applications.

Optical switching is an essential part of photonic integrated circuits and the focus of research at the moment. In this research, an optical switch design working on the phenomenon of the guided-mode resonances in 3D photonic crystals-based structure is reported. The optical-switching mechanism is studied in a dielectric slab-waveguide-based structure operating in the near-infrared range in a telecom window of 1.55 µm. The mechanism is investigated by interference of two signals, i.e., the data signal and the control signal. The data signal is coupled into the optical structure and filtered utilizing guided-mode resonance, whereas, the control signal is index guided in the optical structure. The amplification or de-amplification of the data signal is controlled by tuning the spectral properties of the optical sources and structural parameters of the device. The parameters are optimized first using a single-cell model with periodic boundary conditions and later in a finite 3D-FDTD model of the device. The numerical design is computed in an open-source Finite Difference Time Domain simulation platform. Optical amplification in the range of 13.75 % is achieved in the data signal with a decrease in the linewidth up to 0.0079 µm and a quality factor of 114.58. The proposed device presents great potential in the field of photonic integrated circuits, biomedical technology, and programmable photonics.

The splitting method developed in a previous study for linear, multi – component, convection-diffusion mass transfer equations is extended to non-linear, multi-component, convection-diffusion mass transfer equations. The diffusion term is non-linear (the diffusion coefficients depend on chemical species concentrations). Theoretical results about the splitting error are presented, as well as numerical simulations for mixtures with n ≤ 5. The numerical experiments show second-order accuracy and stability for the present splitting algorithm.

To investigate the impact of a magnetic field on plaque development in a stenotic bifurcated artery, a finite element method is utilized. The blood flow is modelled as a stable, incompressible, Newtonian, biomagnetic, and laminar fluid. Furthermore, the arterial wall is assumed to be linear elastic. The Arbitrary Lagrangian Eulerian (ALE) method is employed to describe the hemodynamic flow in a bifurcated artery under the influence of an asymmetric magnetic field, taking into account two-way fluid-structure interaction coupling. A stable $P_2P_1$ finite element pair discretizes a nonlinear system of partial differential equations that requires a solution. The Newton-Raphson method is utilized to find a solution to the resulting nonlinear algebraic equation system. Numerical modelling is used to simulate the presence of magnetic fields, and the resulting displacement, velocity magnitude, pressure, and wall shear stresses are shown for a range of Reynolds numbers ($Re = 500$, $1000$, $1500$, and $2000$). The results of the numerical analysis demonstrate that the presence of a magnetic field has a significant effect not only on the magnitude of displacement but also on the velocity of the flow. The application of a magnetic field reduces flow separation, extends the recirculation area near the stenosis, and increases wall shear stress.

In this paper a new monolithic Eulerian formulation in the framework of non-classical continuum is presented for the analysis of fluid-strucutre interaction problems. In this respect, Cosserat continuum theory taking into account the micro-rotational degrees of freedom of the particles is considered. Continuum description of the model and variational formulation of the governing flow dynamics for non-classical -fluid-structure interaction nCFSI is presented. The model is analyzed by computing a well known benchmark problem by Hecht and Pironneau [16]. The algorithmic description is presented and implemented using FreeFEM++. Code is validated with the benchmark solution of Turek and Hron [38] in case of flow around a flag attached with cylinder. New microstructral behavior of the solution is studied and numerical simulations and results are shown in the form of figures. Some interesting feature of the flow is observed and microstructural characteristics are discussed.

Alternating current field measurement (ACFM) testing is one of promising techniques in the field of non-destructive testing with advantages of the non-contact capability and the reduction of lift-off effects. In this paper, a novel crack detection approach is proposed to reduce the effect of the angled crack (cack orientation) by using rotated ACFM techniques. The sensor probe is composed of an excitation coil and two receiving coils. Two receiving coils are orthogonally placed in the centre of the excitation coil where the magnetic field is measured. It is found that the change of the x component and the peak value of the z component of the magnetic field when the sensor probe rotates around a crack follows a sine wave shape. A customised accelerated finite element method solver programmed in MATLAB is adopted to simulate the performance of the designed sensor probe which can significantly improve the computation efficiency due to the small crack perturbation. The experiments have also been carried out to validate the simulations. It is found that the ratio between the z and x components of the magnetic field remains stable under various rotation angles. It shows the potential to estimate the depth of the crack from the ratio detected by combining the magnetic fields from both receiving coils (i.e., the x and z components of the magnetic field) using the rotated ACFM technique.

Zero-rate output (ZRO) drift induces deteriorated micro-electromechanical system (MEMS) gy-roscope performances, severely limiting its practical applications. Hence, it is vital to explore an effective method toward ZRO drift reduction. In this work, we conduct an elaborate investigation on the impacts of the internal and packaging stresses on the ZRO drift at the thermal start-up stage, and propose a temperature-induced stress release method to reduce the duration and magnitude of ZRO drift. Self-developed high-Q dual mass tuning fork gyroscopes (TFGs) are adopted to study the correlations between temperature, frequency and ZRO drift. Furthermore, a rigorous finite element simulation model is built based on the actual device and packaging structure, revealing the temperature and stresses distribution inside TFGs. Meanwhile, the relationship between temperature and stresses are deeply explored. Moreover, we introduce a temperature-induced stress release process to generate thermal stresses and reduce the temperature-related device sensitivity. By this way, the ZRO drift duration is drastically reduced from ~2000 s to ~890 s, and the drift magnitude decreases from ~0.4 °/s to ~0.23 °/s. This stress release method achieves a small bias instability (BI) of 7.903 °/h and a low angle random walk (ARW) of 0.792 °/√h, and the long-term bias performance is significantly improved.

To understand the enhanced protection mechanism of CoCrNiAlY-YSZ-LaMgAl11O19 dou-ble-layer ceramic coating with aluminum plating, a finite element simulation method was used to simulate the distribution of thermal stress in the coating in all directions. The results show that in the air exposure of the un-aluminized coating, high temperature causes a large radial thermal stress on the surface of the LaMgAl11O19 (LMA) layer, and it increases with the increase in temperature, which is the main reason for the initiation of axial cracks. After arc aluminum plating, the aluminum plating layer effectively inhibited the volume shrinkage of the coating through good adhesion to the coating and internal diffusion, the thermal stress of the coating was considerably reduced, and the CoCrNiAlY-YSZ-LMA coating had an effective enhancement and protection effect; however, there was still a certain amount of shear thermal stress inside the LMA layer, the top of the crack, and the bottom of the crack. This thermal stress caused the initi-ation of radial microcracks in the LMA layer, which also becomes a risk point for the failure of the aluminum coating.

Variations in the implant thread shape and occlusal load behavior may result in significant changes in the biological and mechanical properties of dental implants and surrounding bone tissue. Most previous studies consider a single implant thread design, an isotropic bone structure, and a static occlusal load. However, the effects of different thread designs, bone material properties, and loading conditions are important concerns in clinical practice. Accordingly, the present study performs Finite Element Analysis (FEA) simulations to investigate the static, quasi-static and dynamic response of the implant and implanted bone material under various thread designs and occlusal loading directions (buccal-lingual, mesiodistal and apical). The simulations focus specifically on the von Mises stress, displacement, shear stress, compressive stress and tensile stress within the implant and the surrounding bone. The results show that the thread design and occlusal loading rate have a significant effect on the stress distribution and deformation of the implant and bone structure during clinical applications. Overall, the results provide a useful insight into the design of enhanced dental implants for an improved load transfer efficiency and success rate.

This paper presents a steady-state and transient heat conduction analysis framework using the polygonal scaled boundary finite element method (PSBFEM) with polygon/quadtree meshes. The PSBFEM is implemented with commercial finite element code Abaqus by the User Element Subroutine (UEL) feature. The detailed implementation of the framework, defining the UEL element, and solving the stiffness/mass matrix by the eigenvalue decomposition are presented. Several benchmark problems from heat conduction are solved to validate the proposed implementation. Results show that the PSBFEM is reliable and accurate for solving heat conduction problems. Not only can the proposed implementation help engineering practitioners analyze the heat conduction problem using polygonal mesh in Abaqus, but it also provides a reference for developing the UEL to solve other problems using the scaled boundary finite element method.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

In this research work, we present a mathematical model for novel coronavirus -19 (NCOVID-19) which is consisted on three different compartments susceptible, infected and recovered classes abbreviated as under convex incident rate involving and emigration rate. We first derive the formulation of the model. Also, we give some qualitative aspects for the model including existence of equilibriums and its stability results by using various tools of nonlinear analysis. Then by mean of nonstandard finite difference scheme (NSFD), we simulate the results against the data of Wuhan city for the sixty days. By means of simulation, we show how protection, exposure, emigration, death and cure rates affect the susceptible, infected and recovered population with the passage of time involving emigration. On the basis of simulation, we observe the dynamical behavior due to emigration of susceptible and infected classes or one of these two.

Transition between free-surface and pressurized flows is an crucial phenomenon in many hydraulic systems, including water distribution systems, urban drainage systems, etc. During the transition, the force exerted on the structures changes drastically, thus it is meaningful to simulate this process. However, severe numerical oscillations are widely observed behind filling-bores, causing unphysical pressure variations and even computation failure. In this paper, some oscillation-suppressing approaches are reviewed and evaluated on a benchmark model. Then a new oscillation-suppressing approach is proposed to admit numerical viscosity when the water surface is at proximity of conduct roof which has first order accuracy. This approach adds numerical viscosity when water surface is at the proximity of conduct roof. It can sufficiently suppress numerical oscillations under an acoustic wave speed of 1000m/s and is simple to apply. In comparison with two experiments, the simulation results of this method show good agreement and little numerical oscillations. The results in this paper can help readers to choose an appropriate oscillation-suppressing method to improve the robustness and accuracy of flow regime transition simulations.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

This work presents a linear smoothing scheme over high-order triangular elements in the framework of a cell-based strain smoothed finite element method for two-dimensional nonlinear problems. The main idea behind the proposed linear smoothing scheme for strain-smoothed finite element method (S-FEM) is no subdivision of finite element cells to sub-cells while the classical S-FEM needs sub-cells. Since the linear smoothing function is employed, S-FEM is able to use quadratic triangular or quadrilateral elements. The modified smoothed matrix obtained node-wise is evaluated. In the same manner with the computation of the strain-displacement matrix, the smoothed stiffness matrix and deformation graident are obtained over smoothing domains. A series of benchmark tests are investigated to demonstrate validity and stability of the proposed scheme. The validity and accuracy are confirmed by comparing the obtained numerical results with the standard FEM using 2nd-order triangular element and the exact solutions.

Mobile elevating work platforms (MEWPs) consist of a work platform, extending structure, and chassis, and are used to move persons to working positions. MEWPs are useful but are composed of pieces of equipment, and accidents do occur owing to equipment defects. Among these defects, accidents caused by the fracture of bolts fixed to the extension structure and swing system are increasing. This paper presents a failure analysis of the fixing bolts of MEWP. Standard procedure for failure analysis was employed in this investigation. Visual inspection, chemical analysis, tensile strength measurement, and finite element analysis (FEA) were used to analyze the failure of the fixing bolts. Using this failure analysis approach, we found the root cause of failure and proposed a means for solving this type of failure in the future. First, the chemical composition of the fixing bolt is obtained by a spectroscopy chemical analysis method, which determined that the chemical composition matched the required standard. The tensile test showed that the tensile and yield strengths were within the required capacity. The stress analysis was carried out at five different boom angles, and it was determined that the fixing bolt of MEWP can withstand the loads at all the boom angles. The outcomes of the fatigue analysis revealed that the fixing bolt fails before reaching the design requirements. The results of the fatigue analysis showed primarily that the failure of the fixing bolt was due to fatigue. A visual inspection of the fractured section of the fixing bolt also confirmed the fatigue failure. We propose a method to prevent failure of the fixing bolt of the MEWP from four different standpoints: the manufacturer, safety certification authority, safety inspection agency, and owner.

Globally 30% of landslides occur in the northeastern part of India [1]. One of the major earthquake events in Sikkim, India occurred on 18th September 2011 (Mw 6.9) led to over 300 landslides and 122 human deaths [2]. These landslides not only controlled by natural disasters but initiated due to human activities. The present study considered Lungchok landslide occurred in south district of Sikkim due to 2011 seismic event. The study focused on the failure mechanism of the landslide based on finite element analysis by adopting eight different cases. The deformation characteristic was investigated for dry and saturated slope conditions under static and dynamic behavior considering vehicle loads using GeoStudio software. The FEM analysis has been carried out using load deformation and linear elastic. The analysis shows that the failure of the slope was not sudden due to the 2011 earthquake event, but progressive failure was observed with time and construction activity. The paper demonstrates that, an increase in infrastructure development including construction by hill cutting increased the initiation of landslide with soil erosion. The cracks developed after 2011 earthquake event led to further deformations during future disasters required effective stabilization measures.

This paper is concerned with representing sums of finite products of Chebyshev polynomials of the second kind and of Fibonacci polynomials in terms of several classical orthogonal polynomials. Indeed, by explicit computations each of them is expressed as linear combinations of Hermite, generalized Laguerre, Legendre, Gegenbauer and Jacobi polynomials which involve the hypergeometric functions ${}_1 F_1$ and ${}_2 F_1$.

This paper reveals the physical properties of Jeffery nanofluid flow past a moving plate embedded in porous medium under the existence of radiation and thermal diffusion. The analysis is carried out in three cases of moving plate, namely stationary plate λ = 0, forth-moving plate λ = 1, back-moving plate λ = −1. Finite difference method is applied to solve the governing equations of the flow and pointed out the variations in velocity, temperature and concentration with the use of graphical presentations. The impact of several parameters on local skin friction, Nusselt number and Sherwood number is also noticed and discussed. Enhancement of velocity is observed under the impact of Jeffery parameter for the cases of stationary plate and back-moving plate, whereas reverse nature is found in the case of forth-moving plate. The velocity enhances as the values of porosity parameter increases for the case of stationary plate and forth-moving plate but a reverse nature is noticed in the case of back-moving plate.

AbstractIntroduction: Consistent utilization of institutional delivery service reduces maternal morbidity and mortality. However, service utilization could in turn influenced by the women’s satisfaction with the service provided by the health care providers. In addition, their satisfactions with the institutional delivery service remains understudied. Assessment of the maternal satisfaction with maternal health service is a major input to improve maternal health services. Objective: To assess the maternal satisfaction with maternal health service and its predictors among the women who gave birth in last 12 months in Darara district, Southern Ethiopia.Methods: A community-based cross-sectional study was done using a mixed method among the sample of 520 women in Darara district, South Ethiopia from June 1-30, 2023. A systematic and purposive sampling procedure was utilized to choice the study subjects. A structured, validated and pretested interview-administrated questionnaire and in-depth interview were utilized to collect the data. The data were entered into Epi data version 3.1 and analyzed using SPSS version 25. The chi-square (X²) test was utilized to determine the overall association between independent and dependent variables. Both bi-variable and multivariable binary logistic regression analyses were conducted. Important assumptions of the binary logistic regression were checked to be satisfied. The coding and analysis of the qualitative data were done using thematic content analysis technique by Atlas-Ti software and presented in narratives. Results: The total maternal satisfaction with maternal health service was 55.2% (95% CI = 50.8-59.4). The identified predictors of maternal satisfaction were distance from household to health post (AOR = 3.59; 95% CI= 1.71 - 7.55), absence of preparation of HEWs during procedure (AOR= 2.87; 95% CI = 1.74 - 4.74), acceptability of the HES by HHs (AOR= 2.18; 95% CI = 1.14 - 4.18), having a reliable communication method with HEWs (AOR = 3.47; 95% CI = 1.77 - 6.79) and received training on the model family (AOR= 2.48, 95% CI= 1.86 - 2.57). These quantitative results were supported by the individual, organizational, socio-demographic and cultural qualitative findings. Conclusions: This study indicated that 55.2% of women were satisfied with maternal service.Distance from household to health post, absence of preparation of HEWs during procedure, acceptability of the Health Extension Service (HES) by household, having a reliable communication method with HEWs and received training on the model family were significant predictors of maternal satisfaction. The interventions to increase maternal satisfaction with HES need to focus on household-based acceptability of them and their reliable communication method in planning and implementing the services. Similarly, expansion of training of model family in the community would increase maternal satisfaction levels.

Hormone changes across women's menstrual cycle may lead to changes in perception of chemical signals and hormonal responses to these cues. The aim of the present study was to determine the role of menstrual cycle phase on the effects of extracts of male axillary secretions (EMAS) in women. We tested healthy reproductive age and premenopausal women (n=29). EMAS/control solution was applied once in two hours either in the follicular or luteal phase, while collecting saliva samples for LH and cortisol monitoring. LH and cortisol concentrations were analyzed using EIA technique. PANAS and VAS were used to assess the mood. We observed a significant increase in the number of LH peaks (p=0.0447) and their amplitude (p=0.0469) when EMAS was applied in the follicular phase. The same application in the luteal phase lowered the amplitude of LH peaks (p=0.0382). EMAS application increases salivary cortisol level in reproductive age women relative to premenopausal women (p=0.0032). PANAS revealed changes in positive and negative affect after EMAS application. Our data indicate the significance of the menstrual cycle phase for EMAS effects on LH secretion, mood, but not on cortisol secretion in women.

This study demonstrates the efficacy of structured pruning and architectural fine-tuning on the YOLOv7-tiny model for eye state detection, emphasizing optimization for real-time applications. Structured pruning significantly reduced the model's complexity and storage size while maintaining high detection accuracy, as evidenced by stable precision, recall, and mAP@.5 metrics across iterations. Further fine-tuning adjusted the model's width and depth, optimizing efficiency and processing speed without compromising performance. These optimizations yielded YOLOv7-tiny variants that are both computationally efficient and accurate, suitable for resource-constrained environments. The findings highlight the critical role of model optimization in deploying effective neural networks for specific detection tasks in real-time scenarios.

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

SiOx films, frequently derived from amino silane precursors, have found several applications with high added value. Although frequently used, the deposition of coatings from Tris(dimethyl amino)silane (TDMAS) has been reported to demand considerable amounts of energy, mainly due to the difficulty of oxidizing such compound. As it is well known, Plasma-enhanced atomic layer deposition (PEALD) is able to improve the oxidation efficiency even under low process temperatures. Owing to that, PEALD can be considered as a very promising technique for the deposition of SiOx coatings. In this work, it has been investigated the deposition of silicon oxide films using TDMAS at 150°C. It has been evaluated the effect of the plasma oxidation time (6 to 18 s) and of the atmosphere composition (pure O2 or O2+Ar) on the chemical structure, elemental composition and chemical bonding state of the films. Increasing the plasma oxidation time in pure O2 resulted in larger proportion of retained C (Si-CH3) whereas N was preserved in the structure (Si-N). on the other hand, the formation of SiOx films from TDMAS is favored in shorter oxidation times in O2 + Ar plasmas.

We study the influence of high-order twisting phases on polarization states and optical angular momentum of a vector light field with locally linear polarization and a hybrid state of polarization (SoP). The initial SoP of a twisted vector optical field (TVOF) modulated by the high-order twisting phase possesses various symmetric distributions. The propagating properties of a high-order TVOF with locally linear polarization and hybrid SoP are explored, including the intensity compression, expansion, and conversion between the linear and circular polarization components. In particular, orbital angular momentum (OAM) appears in a high-order TVOF during propagation where no OAM exists in the initial field. The variation of OAM distribution in cross-section becomes more frequent with the increase of the twisting phase order. In addition, a non-symmetric OAM distribution appears in an anisotropic TVOF, leading to the rotation of the beam around the propagation axis during propagation. These results provide a new approach for optical field manipulation in a high-order TVOF.

Abstract: This study aims to analyze the physico-mechanical properties and dynamic models of tissue-simulating hydrogels, specifically the photoacoustic (PA) response signals, by varying the concentrations of polyvinyl alcohol (PVA) and molecular weight (MW). A state space model (SSM) is proposed to study the PVA hydrogels to retrieve the PA-related signal's damping ratio and nat-ural frequency. Nine box-shaped PVA hydrogels containing saline solution were used, with five concentrations of PVA (7, 9, 12, 15, 20%) for MW1 and four for MW2. The results indicated that the concentration of PVA and MW played an important role in the PA wave's amplitude, arrival time, and speed of sound over the hydrogels. The SSM parameters showed that increasing PVA and MW concentrations improved the hydrogels' ability to absorb and transfer energy under the PA effect. These parameters were also found to be correlated with density and modulus of elasticity. Addi-tionally, the concentrations of PVA and MW affected the absorption and optical scattering coeffi-cients. The physical-mechanical properties, including porosity, density, and modulus of elasticity, improved as the concentration of PVA and MW increased. The ultimate goal of this study is to develop hydrogels as phantoms that can be used for tissue simulation and imaging.

Dialogue State Tracking is an essential component in multi-domain dialogue systems, aiming to accurately determine the current dialogue state based on the dialogue history. Existing research has addressed the issue of multiple mappings in dialogues by employing slot self-attention as a data-driven approach. However, learning the relationships between slots from a single sample has limitations and introduces noise. In this paper, we propose an External Slot Relation Memory-based Dialogue State Tracking model (ER-DST). By utilizing an external memory storage, we learn the relationships between slots as a dictionary of multi-domain slot relations. Additionally, we employ a small filter to discard slot information irrelevant to the current dialogue state. Experimental results on the MultiWOZ2.0 and MultiWOZ2.1 benchmarks demonstrate significant improvements while reducing the time complexity to O(n).

Abstract: Pomegranate peels are important source of polyphenols with remarkable interest in food, pharmaceutical and cosmetic industry. An improved extraction of total polyphenolic com-pounds (TPC) from pomegranate peels by Solid-State Fermentation (SSF) was achieved. A Box Hunter & Hunter (BHH) followed by Central Composite Design (CCD) were performed to assess the effect of the process variables on TPC release. The statistic designs indicate that the best TPC extraction (234.85 mg GAE/gdm) by means of SSF occurs, at 42°C, 50 % moisture, pH 5.0, mineral solution (g/L): NaNO3 (3.83), KH2PO4 (1.52), MgSO4 (4.66) and KCl (1.52) at 36 h. At the best fer-mentation conditions, TPC (248.78±1.24 mgGAE/gdm) increased 5.96-fold than values previously reported and antioxidant activity [AA] increased 5.81-fold than the value obtained before the SSF optimization. High-valued citric acid, α and β punicalin, α and β punicalagin, punigluconin, gal-loyl-HHDP hexoside and ellagic acid molecules were identified. The increased extraction of TPC by SSF provides a suitable alternative for pomegranate peels valorization through the re-covery of molecules with high added value with potential use in food, pharmacy and cosmetic industries; a diversification in the use of food agroindustry by-products is obtained as approach to the circular economy model through biotechnological processes.

Rooftop solar (RTS) projects have the potential to contribute to climate change mitigation and sustainable development objectives. In India, grid-connected RTS capacity has been targeted at 40 GW by the end of the year 2022 however, the installed capacity is limited to 8.2 GW only. As a result, the country missed its 2022 target of installing 100 GW of solar power capacity, largely due to inadequate uptake of RTS. The prevailing practices of RTS implementation is observed to be complex, repetitive, tedious, and time-consuming for potential consumers and there is a lack of coordination among implementing agencies. Therefore, even with vast potential, supportive measures, dedicated policies, and regulations the penetration of RTS systems is far below their respective potential. The introduction of information technology (IT) intervention in the RTS sector would integrate key stakeholders at a single platform so as to reduce the administrative burden of implementing agencies, optimization of processing time, handle multiple consumers simultaneously, and connect consumers with authentic vendors, etc. This would help them to understand and perform their shared roles and responsibilities and enhance the RTS implementation across the state. In this study, the scope for IT interventions in the existing RTS implementation process of the Odisha Renewable Energy Development Agency (OREDA) has been assessed and a simplistic approach has been developed for the execution of the RTS projects in relatively lesser time with the least human interface as well as resources. This approach has been successfully demonstrated with OREDA and a cumulative capacity of around 5 MWp (individual project of 1-2 kWp) residential grid-connected RTS projects implemented through the web platform. Currently, other state nodal agencies are also adopting the model for RTS execution and consumer proliferation through IT interventions.

A silicified, thick-shelled, smooth-surfaced nuculanoid bivalve has been recovered by acid maceration of the Late Triassic (Carnian-Norian) strata of the Luning Formation, Nevada. Comparable modern nuculanoid clams inhabit water depths from 525-2,562 meters, and the living clam (an undescribed species of Pseudoneilonella from Caleta Sierra, Coquimbo, Chile) most similar to the fossil lives at 878-933 m. The Triassic nuculanoid clam (possibly a neilonellid) is inferred here to have inhabited marine waters at approximately 1000 m deep during deposition of the Shaly Limestone Member of the Luning Formation. This new fossil discovery falsifies hypotheses that the ichthyosaurs (Shonisaurus popularis) of Berlin-Ichthyosaur State Park, Nevada, USA, were deposited, respectively, in either shoreline deposits or in strata that accumulated above storm wave base.

Sub-Saharan social-ecological systems are undergoing changes in environmental conditions, including modifications in rainfall pattern and biodiversity loss. Consequences of such changes depend on complex causal chains which call for integrated management strategies whose efficiency could benefit from ecosystem dynamic modelling. However, ecosystem models often require lots of quantitative information for estimating parameters, which is often unavailable. Alternatively, qualitative modelling frameworks have proved useful for explaining ecosystem response to perturbations, while requiring fewer information and providing more general predictions. However, current qualitative methods have some shortcomings which may limit their utility for specific issues. In this paper, we propose the Ecological Discrete-Event Network (EDEN), an innovative qualitative dynamic modelling framework based on "if-then" rules which generates many alternative event sequences (trajectories). Based on expert knowledge, observations and literature, we use this framework to assess the effect of permanent changes in surface water and herbivores diversity on vegetation and socio-economic transitions in an East African savanna. Results show that water availability drives changes in vegetation and socio-economic transitions, while herbivore functional groups had highly contrasted effects depending on the group. This first use of EDEN in a savanna context is promising for bridging expert knowledge and ecosystem modelling.

Hydrogenated amorphous silicon (a-Si:H) can be produced by plasma-enhanced chemical vapour deposition (PECVD) of SiH4 (Silane) mixed with Hydrogen. The resulting material shows outstanding radiation resistance properties and can be deposited on a wide variety of different substrates. These devices have been used to detect many different kinds of radiation namely: MIPs, x-rays, neutrons and ions as well as low energy protons and alphas. However, MIP detection using planar diodes has always been difficult due to the unsatisfactory S/N ratio arising from a combination of high leakage current, high capacitance and a limited charge collection efficiency (50% at best for a 30 µm planar diode). To overcome these limitations the 3D-SiAm collaboration proposes to use a 3D detector geometry. The use of vertical electrodes allows for a small collection distance to be maintained while conserving a large detector thickness for charge generation. The depletion voltage in this configuration can be kept below 400 V with consequent reduction in the leakage current. In this paper, following a detailed description of the fabrication process, the results of the tests performed on the planar p-i-n structures made with ion implantation of the dopants and with carrier selective contacts will be illustrated.

State legitimacy and effectiveness could be seen by the way to deliver welfare to citizens to mitigate social grievances, that could eventually lead to conflicts (Kivimäki, 2021). Social security systems in Maghreb countries are quite similar in their architecture and aims to provide social insurance to all the workers in the labor market. However, they suffer from the same main problem: the low rate of enrollment of workers. Many workers (employees and self-employed) work informally without any social security coverage. The issue of whether informal jobs are chosen voluntarily by workers or as a strategy of last resort is controversial. Many authors recognize that the informal sector is heterogeneous and it is made up of workers who voluntary choose it and others who are pushed inside because of entry barriers to the formal sector (Günther & Launov, 2012). Using the SAHWA survey and discrete choice models, this article confirms the heterogeneity of the informal labor market in three Maghreb countries: Algeria, Morocco, and Tunisia. Furthermore, this article highlights the profiles of workers who voluntarily choose informality, which is missing from previous studies. Finally, this article proposes policy recommendations in order to extend social security to informal workers and to include them in the formal labour market.

New pharmaceutically acceptable salts of trazodone for the treatment of central nervous system disorders are synthesized and described. Each salt (trazodone hydrogen bromide and trazodone 1-hydroxy-2-naphthoate) was obtained by two or three different methods leading to the same crystalline form. Although trazodone salts are poorly crystalline, single-crystal X-ray diffraction data for trazodone 1-hydroxy-2-naphthoate were collected and analyzed as well as compared to the previously described crystal structure of commercially available trazodone hydrochloride. The powder samples of all new salts were characterized by Fourier transform infrared spectroscopy and 13C solid-state nuclear magnetic resonance spectroscopy. Spectroscopic studies were supported by gauge including projector augmented wave (GIPAW) calculations of carbon chemical shielding constants. The main goal of our research was to find salts with better physicochemical properties and to make an attempt to associate them with both the anion structure and the most prominent interactions exhibited by the protonated trazodone cation. The dissolution profiles of trazodone from tablets prepared from various salts with lactose monohydrate were investigated. The studies revealed that salts with simple anions show a fast release of the drug while the presence of more complex anion, more strongly interacting with the cation, effects a slow-release profile of the active substance and can be used for the preparation of the tables with a delay or prolonged mode of action.

In this paper, the stability control of the inverted pendulum on a cart with a disturbance forces has been done using observer based and full state feedback H2 controllers. The Lagrangian equation has been used to model the system equation of motions and linearized the system to the unstable upward position. Comparison of the system stability has been simulated by comparing the proposed controllers using Matlab/Scripts and a promising results has been analyzed successfully.

In this paper, the design of a low cost portable ventilator with performance analysis have been done to solve the scarcity of respiratory ventilators for COVID-19 patients. The materials used to build the system are: DC motor, rotating disc and pneumatic piston. The system input is the patient heart beat and the output is volume of air to the patient lung with adjusted breathing rate. This ventilator adjusts the breathing rate to the patient depending on his heart beat rate. The performance analysis of this system have been done using Proportional Integral Derivative (PID) and Full State Feedback H2 controllers. Comparison of the system with the proposed controllers have been done using a step change and a random change of the patient heart beat and a promising result have been analyzed successfully.

Room-temperature phosphorescent (RTP) materials have been attracted tremendous interest owing to their unique material characteristics and potential applications for state-of-the-art optoelectronic devices. Recently, we have reported a synthesis and fundamental photophysical properties of new RTP materials based on benzil, i.e., fluorinated monobenzil derivative and fluorinated and non-fluorinated bisbenzil derivative analogues [Yamada, S. et al, Beilstein J. Org. Chem. 2020, 16, 1154–1162.]. To further understand their RTP properties, here we investigated the excited-state dynamics and photostability of the derivatives by means of time-resolved and steady-state photoluminescence spectroscopies. For these derivatives, clear RTP emissions with lifetimes on the microsecond timescale were identified. Among them, the monobenzil derivative was found to be the most efficient RTP material, showing both the longest lifetime and highest amplitude RTP emission. Time-resolved photoluminescence spectra measured at 77 K and density functional theory calculations revealed the existence of a second excited triplet state in the vicinity of the first excited singlet state for the monobenzil derivative, indicative of the presence of a fast intersystem crossing pathway. A discussion of the correlation between the excited state dynamics, emission properties, and conformational flexibility of the three derivatives is presented.

Background: Social skills deficits are present in 43.3% of major depressed patients and significantly impact health-related quality of life. However, studies concerning social deficits as state-dependent markers of depression are limited. Objective: To delineate the effects of severity of depression, personality characteristics, family support satisfaction and self-esteem on social skills in clinical depression. Methods: We recruited 150 patients with major depressive disorder or persistent depressive disorder and assessed 1) Beck Depression Inventory-II (BDI-II), 2) Social Skill Inventory (SSI), 3) Family Adaptation, Partnership, Growth, Affection, Resolve (APGAR) Questionnaire 4) Rosenberg Self-Esteem Scale (RSES) and 5) Maudsley Personal Inventory (MPI). Results: Social skills deficits were significantly associated with female gender, age < 40 years, depression severity, introvert / neurotic personality, and lowered family support satisfaction and self-esteem. A large part of the variance (47.2%) in social skills deficits was predicted by satisfaction of family support, introvert personality, and low self-esteem. Exploratory Factor Analysis showed that a bifactorial model best fitted the data with a) a general factor loading highly on BDI-II, SSI emotional and social, APGAR, RSES, MPI_introvert and MPI_neurotic scores, and b) a single-group factor loading on both SSI, RSES, and MPI introvert scores. Conclusion: In clinical depression, social skills deficits covary with increasing severity of depression and thus constitute a state marker of depression, and independently from severity of depression covary with introvert personality features. As such, remission of social skills deficits may emerge as a novel objective for the treatment of depression and prevention of new episodes.

This paper studies the integrated design problems of control and guidance with parameter uncertainties, target disturbances, input constraints and actuator faults. Firstly, based on the integrated design idea of the missile guidance and control, the auxiliary variable is used to establish and transform it into a cascade system with input constraints, actuator faults and disturbances of unknown upper bounds. Secondly, the adaptive anti-saturation dynamic surface fault-tolerant controller is designed by using the back-stepping method, adaptive control, auxiliary system and tracking differentiator. By introducing the tracking differentiator and tangent barrier Lyapunov function, the computational explosion problem in the traditional back-stepping method is avoided and the angle of attack can be guaranteed in prospective range, respectively. Finally, the theoretical proof of the designed control strategy is given to ensure that the states of the closed-loop system are bounded. At the same time, the digital simulation of the maneuvering target of different maneuvering forms is carried out, which further illustrate the effectiveness and robustness of the designed control schemes.

A mathematical model given by a two - dimensional differential system is introduced in order to understand the transition process from the normal hematopoiesis to the chronic and accelerated acute stages in chronic myeloid leukemia. A previous model of Dingli and Michor is refined by introducing a new parameter in order to differentiate the bone marrow microenvironment sensitivities of normal and mutant stem cells. In the light of the new parameter, the system now has three distinct equilibria corresponding to the normal hematopoietic state, to the chronic state, and to the accelerated acute phase of the disease. A characterization of the three hematopoietic states is obtained based on the stability analysis. Numerical simulations are included to illustrate the theoretical results.

The feasibility of a steady-state visual evoked potential (SSVEP) brain-computer interface (BCI) with a single flicker stimulus for multiple-target decoding has been demonstrated in a number of recent studies. The single-flicker BCIs have mainly employed the direction information for encoding the targets, i.e. different targets are placed at different spatial directions relative to the flicker stimulus. The present study explored whether visual eccentricity information can also be used to encode target for the purpose of increasing the number of targets in the single-flicker BCIs. A total number of 16 targets were encoded, placed at eight spatial directions, and two eccentricities (2.5° and 5°) relative to a 12 Hz flicker stimulus. Whereas distinct SSVEP topographies were elicited when participants gazed at targets of different directions, targets of different eccentricities were mainly represented by different signal-to-noise ratios (SNRs). Using a canonical correlation analysis-based classification algorithm, simultaneous decoding of both direction and eccentricity information was achieved, with an average offline 16-class accuracy of 66.8±16.4% averaged over 12 participants and a best individual accuracy of 90.0%. Our results demonstrate a single-flicker BCI with a substantially increased target number towards practical applications.

Understanding the stability limit of crystalline materials under variable tensile stress conditions is of capital interest for their technological applications. In this study, we present results from first-principles density functional theory calculations that quantitatively account for the response of selected covalent and layered materials to general stress conditions. In particular, we have evaluated the ideal strength along the main crystallographic directions of 3C and 2H polytypes of SiC, hexagonal ABA stacking of graphite and 2H-MoS2. Transverse superimposed stress on the tensile stress was taken into account in order to evaluate how the critical strength is affected by these multi-load conditions. In general, increasing transverse stress from negative to positive values leads to the expected decreasing of the critical strength. Few exceptions found in the compressive stress region correlate with the trends in the density of bonds along the directions with the unexpected behavior. In addition, we propose a modified spinodal equation of state able to accurately describe the calculated stress-strain curves. This analytical function is of general use and can also be applied to experimental data anticipating critical strengths and strains values and providing informattion on the energy stored in tensile stress processes.

In the present study, a hybrid optimizing algorithm has been proposed using Genetic Algorithm (GA) and Particle Swarm Optimization (PSO) for Artificial Neural Network (ANN) to improve the estimation of electricity demand of the state of Tamil Nadu in India. The GA-PSO model optimizes the coefficients of factors of gross state domestic product (GSDP), per capita demand, income and consumer price index (CPI) that affect the electricity demand. Based on historical data of 25 years from 1991 till 2015 , the simulation results of GA-PSO models are having greater accuracy and reliability than single optimization methods based on either PSO or GA. The forecasting results of ANN-GA-PSO are better than models based on single optimization such as ANN-BP, ANN-GA, ANN-PSO models. Further the paper also forecasts the electricity demand of Tamil Nadu based on two scenarios. First scenario is the "as-it-is" scenario , the second scenario is based on milestones set for achieving goals of "Vision 2023" document for the state. The present research also explores the causality between the economic growth and electricity demand in case of Tamil Nadu. The research indicates that the direct causality exists between GSDP and the electricity demand of the state.

We present a generalized state-space model formulation particularly motivated by an online scheduling perspective. Through these proposed generalizations, we enable a natural way to handle routinely encountered disturbances and a rich set of corresponding counter-decisions. Thereby, greatly simplifying and extending the possible application of mathematical programming based online scheduling solutions to diverse application settings.

The excited-state lifetimes of the anticoagulant drug warfarin (W) in water and in the absence and presence of methyl-β-cyclodextrins (Me-β-CD) were recorded using time-resolved fluorescence measurements. Selective excitation of the open and cyclic protonated isomers of W were acquired with laser emitting diodes (LED) producing 320 and 280 nm excitation pulses, respectively. Formation of the inclusion complex was checked by UV–visible absorption spectroscopy, and the values of binding constants (2.9 × 10³ M^–1 and 4.2 × 10² M^–1 for protonated and deprotonated forms, respectively) were extracted from the spectrophotometric data. Both absorption and time-resolved fluorescence results established that the interior of the macromolecular host binds preferentially the open protonated form, red shifts the maximum of its absorption of light at ~305 nm, extends its excited-state lifetime, and decreases its emission quantum yield (ФF). Collectively, sequestration of the open guest molecules decreases markedly their radiative rate constants (kr), likely due to formation of hydrogen-bonded complexes in both the ground and excited states. Due to lack of interactions, no change was observed in the excited-state lifetime of the cyclic form in the presence of Me-β-CD. The host also increases the excited-state lifetime and ФF of the drug deprotonated form (W¯). These later findings could be attributed to the increased rigidity inside the cavity of Me-β-CD. The pKa values extracted from the variations of the UV–visible absorption spectra of W versus the pH of aqueous solution showed that the open isomer is more acidic in both ground and excited states. The positive shifts in pKa values induced by three derivatives of cyclodextrins: HE-β-CD, Ac-β-CD, and Me-β-CD supported the preferential binding of these hosts to open isomers over cyclic.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Spacecraft recovery technology is crucial in the field of aerospace, in which the parachute plays a key role in slowing down the descent speed of the spacecraft and realizing a smooth landing. In order to construct a dynamically adjustable parachute deployment strategy, it is necessary to measure the parachute dynamic load accurately in real time. However, the existing sensor measurement scheme is difficult to meet the measurement requirements due to its large structure and complex wiring. In order to meet the current demand for real-time measurement of parachute cords dynamic load, a miniature measuring instrument is designed.According to the function and technical requirements of the miniature measuring instrument, the hardware modules of the acquisition system are selected and designed, and the integration debugging and performance optimization of the microcontroller module, A/D sampling module, signal acquisition circuit and power supply module are carried out. The software of the parachute cords tension acquisition system based on the miniature measuring instrument is developed. The elastomer is modeled by using SolidWorks and statically analyzed by using AnsysWorkbench finite element analysis software. Then the final structure of the elastomer and the pasting position of the strain gage are determined through the results analysis as well as experimental verification. The hardware module of the signal acquisition system for the miniature measuring instrument is then encapsulated. The force value of the miniature measuring instrument is calibrated and tested many times by using the microcomputer-controlled electronic universal testing machine. The experimental results show that the designed miniature measuring instrument has accurate data, strong stability and good real-time performance, which meets the demand for real-time accurate measurement of miniature measuring instrument, and can provide reliable data for parachute cords parameter validation and stepless unfolding design.

Cascading landslides represent a dynamic and hazardous geological phenomenon, char-15 acterized by a sequential chain of slope failures triggered by various factors such as heavy rainfall, 16 seismic activity, or anthropogenic activities. These events can amplify the damage caused by the 17 initial trigger and propagate instability along a slope, often resulting in significant environmental 18 and societal impacts. The Morino-Rendinara cascading landslide, situated in the Ernici mountains 19 along the border of Abruzzo and Lazio region (Italy), serves as a notable example of the complexities 20 and devastating consequences associated with such events. In March 2021, a substantial debris flow 21 event in Morino obstructed the Liri River, marking the latest step in a series of landslide events 22 characterized by a complexity far beyond initial expectations. This study employs a multidiscipli-23 nary approach, combining conventional techniques and advanced technologies, to understand the 24 complexities of the Morino-Rendinara landslide. Field activities, UAV image acquisition, SAR inter-25 ferometry based on SENTINEL-1 images and pixel offset analysis based on high-resolution Google 26 Earth images, offer insights into the geological and hydrogeological setting of the unstable slope, 27 landslide geometry, mechanism and kinematics. To supplement the analysis a specific FEM slope 28 stability analyses is used to reconstruct the deep geometry of the system emphasizing the modula-29 tion action of groundwater flow to the slope stability

Geothermal energy, being a clean energy source, has immense potential, and accurate wellbore modeling is crucial for optimizing the drilling process and ensuring safety. This paper presents a novel geothermal wellbore model based on the drift-flux approach, tested under three different temperature and pressure well conditions. The proposed model integrates the conservation equations of mass, momentum, and energy, incorporating the gas-liquid two-phase flow drift-flux model and heat transfer model. Key features include handling heat transfer between the for-mation and the wellbore, addressing the slip relationship between gas and liquid phases, and accounting for wellbore friction. The nonlinear equations are discretized using the finite differ-ence method, and the highly nonlinear system is solved using the Newton-Raphson method. Numerical simulation, validation, and comparison with existing models demonstrate the en-hanced accuracy of this model. In our tests, the model achieved high accuracy in calculating bottom hole pressure and temperature, with Mean Relative Errors (MRE) significantly lower than those of other models. These results offer valuable insights for optimizing drilling parameters and ensuring drilling safety. Comparisons indicate that this approach significantly outperforms others in capturing the complex dynamics of geothermal wellbores, making it a superior tool for geo-thermal energy development.

While there are well-known synthetic methods in the literature to find the image of a point under circular inversion in l2−normed geometry (Euclidean geometry), there is no similar synthetic method in Minkowski geometry, also known as the geometry of finite-dimensional Banach spaces. In this study, we have succeeded in giving a synthetic construction for the circular inversion in l1−normed spaces, which is one of the most fundamental examples of Minkowski geometry. Moreover, this synthetic construction has been given using the Euclidean circle, independently of the l1−norm.