The Software-Defined Networking concept plays an important role in network management. The central controller, which is the main element of SDN, allows to provide traffic engineering and security solutions in single and multiple-layer networks based on optical transmission. In this work, we compare selected open-source implementations of SDN controllers. Throughput and latency measurements were analyzed using the CBench program. The simulation of a link failure and a controller failure were conducted using the API provided by the Mininet network simulator. For detecting security vulnerabilities, a dedicated program, called sdnpwn, was used. The work provides an overview of the selected controllers, indicating their strengths and weaknesses. Moreover, some implemention suggestions and recommendations are presented.

Self-report measurement is frequently used in human sports to assess training adaptations [1, 2]. This is a technique novel to the equestrian sport. The aim of this study was to describe how elite event riders of Germany evaluate their own fitness as well as that of their horses for the entire duration of an eventing season. Additionally, correlations with possible influencing external factors such as type of training or duration of grazing were also investigated. Short online questionnaires were used to allow eight riders to describe the training of their horses. Five criteria (general performance, ability to concentrate, general state of mind, general muscular condition and emotional wellbeing) were used to assess both, their horse's, as well as their own wellbeing. A 1-10 rating scale was used to score each criterion resulting in an average of 38 points out of 50 (maximum wellbeing) for horse (Std. dev. 0.55) and rider (Std. dev. 0.65) respectively. A total of 120 questionnaires were analysed. A correlation could be demonstrated (Spearman's correlation coefficient = 0.5) between rider and horse score, whereby it only became a linear correlation above 30 points. In addition, the horse score correlates positively with its success at competitions. While the horses were rated similarly throughout the season, the riders’ perceived welfare was higher in the middle of the season compared with the beginning and end of the season. Regularly turned-out horses resulted in higher horse scores (Linear mixed model, p=0,04, n=120). It can be concluded that the self-report measurement of fatigue and wellbeing can be a useful tool for trainers and riders to better determine the horse’s fatigue and recovery. It should be noted that external factors influence both, rider and horse assessment.

The paper highlights the performance of the seismic isolation devices, installed on retrofitted buildings in reducing the seismic response when subjected to earthquakes. Two buildings from the beginning of the XX-th century in Bucharest are chosen from many more, monitored over the city area. We discuss the response of these base-seismic isolated structures, relying on good quality data acquired from the recent strong earthquake (03.11.2022, MW = 5.0). Elastic response spectra computed from recordings at two levels of each structure are used, placed under and right above the isolating layer. At one building the existence of previous recordings and the particularity of the sensors allow a comparison with other two relatively recent medium intensity earthquakes. The assessment is carried out in terms of maximum acceleration amax, measured at certain levels in each structure, spectral acceleration amplitude SAmax and spectral-peak corresponding period. We find that the base-isolation methodology is effective in reducing the response of the building right above the isolating layer, an observation valid for both structures, all components of the recordings, and spectral acceleration values. Moreover, the outcomes from the modal evaluation performed prior to rehabilitation and seismic isolation process are presented, by pointing out a higher newly acquired fundamental period of the isolated structures.

This research addresses the formidable challenge of achieving precise trajectory tracking for autonomous vehicle formations in uncertain environments. It introduces an adaptive control system tailored for autonomous vehicles, with a primary focus on ensuring prescribed performance in trajectory tracking within a leader-follower formation paradigm. The system incorporates a guidance law that allows the leader vehicle to dynamically adjust desired yaw angles and speeds for follower vehicles based on the established reference trajectory, enhancing tracking accuracy and responsiveness to environmental changes. To address practical external disturbances, the study utilizes Radial Basis Function Neural Networks (RBFNN) in conjunction with second-order filters for error approximation. This approach is further strengthened by a carefully formulated adaptive law. The innovative integration of a barrier Lyapunov function with the backstepping method significantly enhances the system’s adaptability and robustness, ensuring trajectory tracking performance meets predetermined standards. Simulation results illustrate the control system’s adept handling of various external disturbances, consistently maintaining trajectory tracking errors within predefined limits. This underscores the system’s potential to markedly enhance the operational reliability and efficiency of autonomous vehicle formations in unpredictable environmental conditions.

Numerous elements, such as the composition and characteristics of carbon nanomaterials, the composition and characteristics of the matrix material, moisture levels, temperature, and loading circumstances, influence the piezoresistive behaviour of self-sensing cementitious composites. While some past research has explored the impact of some of these factors on the performance of self-sensing cementitious composites, additional investigations need to be conducted to delve into how loading conditions affect the sensitivity of self-sensing cement-stabilized composites. Therefore, this study explores the influences of various loading conditions (i.e., location of loading regarding the location of recording electrodes, and loading level) on the electromechanical performance of self-sensing cement-stabilized sand. To this end, firstly, the evaluation of the percolation threshold based on 10% cement-stabilized sand specimens containing various multiwall carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) was performed. Then, 10% cement-stabilized sand containing 4% MWCNTs/GNPs was tested under various cyclic compressive stresses. The results suggested that the distance between the loading area and the electrode location used for recording the electrical resistance significantly impacts the sensitivity of cement-stabilized sand. Optimal sensitivity was achieved when the electrodes were positioned directly beneath the loading area. Moreover, the study yielded that the stress sensitivity of self-sensing cement-stabilized sand increases proportionally with the stress level. Examination through scanning electron microscopy (SEM) demonstrated that the loading condition influences the bridging characteristics of carbon nanomaterials in cement-stabilized sand, leading to diverse electromechanical behaviors based on the loading condition. This study underscores the importance of considering specific parameters when designing the application of self-sensing cement-stabilized sand for practical field use.

This research hypothesised that the use of Virtual Reality (VR) applications can be used to train people in the ability to acquire targets faster, with greater accuracy when using motion controllers than compared with a traditional pointing device (mouse) on a 2D display. User performance was defined and measured using Reaction Time and Accuracy. The research findings suggests that the use of motion controllers in VR improved Reaction Time but not Accuracy when compared against the traditional pointing device and 2D display. This suggests that VR can be used specifically in training scenarios where Reaction Times are more important than Accuracy. It is recommended that further research is conducted using a wider range of hardware and software configurations with a stratified sample that takes into account age and gender to expand the collective understanding of factors that impact on VR aiming and target acquisition in VR.

The envelope (façade) of a building is the first barrier between the exterior and the interior of the building and withstands the highest variation of temperature and solar radiation. Trombe walls are used to take advantage of that and contribute to the heating of interior air, helping the heating system. In this study, a new Trombe wall design is presented with the aim to contribute significantly to the ventilation of residential buildings. For this an exterior wall equipped with a proposed Trombe system was studied in a numerical simulation analysis. The proposed systems consist of two parts, the air cavities on the exterior of the wall, covered with silica glass, and another layer used for heat transfer, on the interior, comprised of a MPCLBs wall of 115mm. Two cities in Romania were considered to represent the coldest and hottest climate in Romania. Brașov representing the cold climate and Constanța representing the hot climate. In the investigation, both the presence and absence of solar radiation were taken into account. In total 4 cases were established. For all four cases monthly research was made using monthly means temperature, direct and diffuse solar radiation. The results are promising and illustrate that the system works the best during the transitional seasons of spring and autumn. The lower the outdoor temperature the higher the temperature can be increased. Overall, solar radiation accounted for an average of 2 °C increase. The temperature increase varied between 3.4 °C to 15.99 °C for Brașov and between 6.42 °C to 12.07 °C in Constanța.

The detrimental consequences of soil pollution caused by crude oil or petroleum products are immense, leading to land degradation, property damage, and rendering agricultural practices ineffective. Extensive research has been conducted in the field of soil remediation, but further studies are still required to explore additional details of the remedial process. As a result, this study focuses on evaluating the effectiveness of Vernonia Galamensis and Vernonia Amygdalina, commonly known as bitter leaf, in remediating hydrocarbon-contaminated soil. In the analysis of micro-organisms, it was found that the bitter leaf extracts contained three types of bacteria: Pseudomonas aeruginosa, Staphylococcus aureus, and Escherichia coli. The leaf extracts were prepared using different methods, including sun drying, room drying, and using them in their wet form, which were then blended into the contaminated soil. The study also took into consideration three different types of soil: sandy-loamy soil, clay soil, and swamp soil. These advanced techniques and considerations are relevant to the topic of revolutionizing soil remediation, as they explore the potential of bitter leaf extracts and different soil types in effectively mitigating the effects of hydrocarbon contamination.The findings revealed that the wet blended extracts of Vernonia performed exceptionally well in the remediation process, surpassing a 50% reduction in the initial contamination levels. The study involved utilizing a quantity of bitter leaf ranging from 10g to 40g, which was added to the contaminated soils and monitored for a duration of 40 days. Remarkably, this approach led to a significant decrease in the concentration of contaminants within the soil, indicating the effectiveness of the bitter leaf extracts in the remediation process. Towards the conclusion of the study, predictive models were constructed to forecast the impact of hydrocarbon content, as well as the levels of lead, zinc, and chromium in the soil. These variables served as the dependent variables in the models, while the mass of bitter leaf, the duration of treatment, and the pH of the soil were considered as independent variables. Significantly, the models achieved a level of significance of less than 0.05, indicating their statistical validity. Furthermore, the r2 value, which represents the goodness of fit, demonstrated an appreciable level of accuracy in predicting the remediation effects. These results highlight the potential of the developed models in assessing and predicting the remedial outcomes of hydrocarbon contamination using bitter leaf extract.

The goal of this study was to characterize the initial growth trajectory of Epicrates assisi, 1 Epicrates cenchria, and Epicrates crassus snakes raised in captivity. An exponential model with 2 parameters for birth weight (A) and growth rate (k) was fitted for each animal. There was a significant 3 difference A and k among the three species, the means (standard error) for A and k parameters were 4 31 (0.3) g and 0.0027 (0.00006) for E. assisi, 27.6 (0.6) g and 0.0046 (0.00013) for E. cenchria and 25.9 5 (1.4) g and 0.0033 (0.00027) for E. crassus. We showed a significative variability between species for 6 initial growth trajectory. In addition, we also demonstrated the existence of variability within species, 7 which can be used to change the growth trajectory of snakes, being a tool for selection and genetic 8 improvement.9

Abstract：To investigate the effects of feeding the Lincomycin and faecal bacterial on weaning stress in Tibetan piglets, we divided the weaned Tibetan piglets at 30 days of age into four groups. We measured growth performance, blood physiological indexes, and metabolomics. The results showed that the Ant, Tib, and Fec groups significantly reduced the ratio of diarrhoea to feed/weight (F/G) and increased the average daily gain (ADG) compared to the Nor group (p < 0.01). The Nor group had significantly lower leukocyte counts, hemoglobin levels, and erythrocyte counts compared to the other three groups on 21d (p < 0.05). These physiological indexes tended to stabilize on 42d. We found that there were beneficial metabolites and metabolic pathways for gastrointestinal function. Specifically, the porphyrin metabolic pathway was elevated in the Ant group, and the tryptophan metabolic pathway was significantly elevated in the Tib and Fec groups compared to the Nor group (p < 0.05). In conclusion, adding faecal bacterial supernatant and fifteen-flavour black pills of Tibetan medicine to the feed reduced the rate of diarrhoea and improved the growth performance of piglets. Moreover, it had an effect on microorganisms and their metabolites and pathways in the gastrointestinal tract of the animals, which might be the main reason for influencing the diarrhoea rate of weaned Tibetan piglets and the growth and development of the piglets. This study provides a new approach for anti-stress applications in weaned Tibetan piglets and the development of substitute anti-products.

This study aimed to investigate the current status of the Sustainable Workplace Equality Policy (SWEP) in an emerging country—Kuwait—and how it impacts firms’ financial and market performance. The study included companies listed in the Kuwait Boursa (Boursa Kuwait is the operator of the Kuwait Stock Exchange) in the period between 2012 and 2020. A disclosure index was prepared for SWEP based on guidelines provided by a combination of various sources and standards such as the Global Reporting Initiatives (GRI) standard, S&P global corporate sustainability assessment, Dow Jones sustainability index, United Nations global compact, and KPMG sustainability reporting standards. Time series regression analysis was used to examine the study hypotheses. The analysis revealed a strong positive relationship between the SWEP disclosure and firm measures of financial performance. The results indicate that SWEP is value-relevant and affects firms’ market value, suggesting that investors should consider firms’ disclosure of the SWEP when making investment decisions. The results of the current study are of interest to several stakeholders, especially investors and policymakers. Specifically, the study is relevant to the Kuwaiti Government, which has defined a clear path for sustainable growth with the Vision 2035/New Kuwait that is aimed at transforming the country into a financial and commercial hub for the region by 2035.

The objectives of this article are to examine whether the application of digitalization in enterprise budgeting affects the fulfilment of budgeting functions and their qualitative characteristics, and to investigate whether the realization of budgeting functions brings benefits. The research was conducted from the perspective of contingency theory, both internal and external conditions. The study used an online survey targeting company budgeting staff. Structural Equation Modelling was utilized to validate the structural model (PLS-SEM technique). The conclusions confirm that the application of digitalization, which particularly pertains to ERP, Business Intelligence systems and accounting systems with budgeting solutions, positively impacts the fulfilment of budgeting functions and most of their qualitative characteristics, while Blockchain makes a minor contribution. Our research suggests that contingency variables, particularly internal ones such as company size, the quality of the organizational structure, and support for competitive strategy, continue to affect budgeting implementation even with the participation of digitalization in budgeting. Budgeting functions and their qualitative aspects are notably correlated with the advantages derived from budgeting, including financial performance, sustainable development and budget task execution.

Permeable asphalt pavement refers to an asphalt mixture layer with an air void content of more than 18% and internal water permeability and drainage capabilities, which can quickly drain away water on the road surface, improve rainy day travel safety and ride comfort. This paper aims to explore the optimal asphalt mixture mix design for long longitudinal slope roads. By using CT scanning technology to analyze the air void content of different rotated and compacted asphalt mixture specimens, and extensively testing and evaluating the performance of permeable pavement mixtures, the following conclusions are drawn: Based on the research philosophy of functional integration, a new asphalt mixture gradation suitable for long longitudinal slope roads is proposed, with the optimal key factor composition being: 0.075mm passing rate of 7%, 2.36mm passing rate of 20%, 9.5mm passing rate of 55%, and oil-stone ratio of 4.8%. The FAM mixture was divided into three parts for air void analysis, with the upper part having a slightly higher air void content than the lower part. The air void distribution diagram of the FAM mixture is concave, with higher air void rate curves on both sides and a lower middle curve. Compared with laboratory dry measurement method, CT scanning test showed slightly higher air void content in specimens. Through dynamic modulus testing, the strength requirement for road asphalt mixture in pavement structure design was evaluated. It was found that at high temperature conditions (50℃), the minimum dynamic modulus value of the FAM mixture was 323 MPa, with a peak value of 22746MPa at a temperature of -10℃ and a frequency of 25HZ. The dynamic modulus value at high temperature conditions is lower than at low temperature conditions, while the dynamic modulus value at high frequency conditions is higher than at low frequency conditions. This study provides useful information and experimental data for the design of new asphalt mixtures for long longitudinal slope roads, and has conducted in-depth research on the air void distribution and performance of the mixture, providing strong support for related research fields and practical applications.

(1) Background: The analysis of athletic performance has always aroused great interest from sport scientist. This study utilized machine learning methods to build predictive models using a comprehensive CrossFit (CF) dataset, aiming to reveal valuable insights into the factors influencing performance and emerging trends.; (2) Methods: The study used Random Forest (RF) and Multiple Linear Regression (MLR) models to predict performance in four key weightlifting exercises within CF: clean &amp; jerk, snatch, back squat, and deadlift. Performance was evaluated using R-squared (R2) values and Mean Squared Error (MSE). Feature importance analysis was conducted using RF, XGBoost, and AdaBoost models.; (3) Results: The RF model excelled in deadlift performance prediction (R2 = 0.80), while the MLR model demonstrated remarkable accuracy in clean &amp; jerk (R2 = 0.93). Across exercises, clean &amp; jerk consistently emerged as a crucial predictor. The feature importance analysis revealed intricate relationships among exercises, with gender significantly impacting deadlift performance.; (4) Conclusions: This research advances our understanding of performance prediction in CF through machine learning techniques. It provides actionable insights for practitioners, optimize performance, and demonstrates the potential for future advancements in data-driven sports analytics.

The Jeryak, a hybrid offspring of Gannan yak and Jersey cattle, exhibits evident hybrid advantages over the Gannan yak in terms of production performance and other various aspects. The small non-coding RNAs known as miRNAs exert a significant regulatory influence on gene expression post-transcriptionally. However, the regulatory mechanism of miRNA associated with muscle development in Jeryak remains elusive. To elucidate the regulatory role of miRNAs in orches-trating the skeletal muscle development in Jeryak, we selected dorsal longissimus muscle tissues from Gannan yak and Jeryak for transcriptome sequencing analysis. A total of 230 (DE)miRNAs and 1819 differentially expressed mRNAs (DEMs) were identified in the longest dorsal muscle of Gannan yak and Jeryak. The functional enrichment analysis revealed a significantly enrichment of target genes from differentially expressed (DE)miRNAs and DEMs in signaling pathways associ-ated with muscle growth, such as the Ras signaling pathway and the MAPK signaling pathway. The network of interactions between miRNA and mRNA suggested that some differentially ex-pressed miRNAs, including miR-2478-z, miR-339-x, novel-m0036-3p and novel-m0037-3p, played a pivotal role in facilitating muscle development. These findings help us to deepen our under-standing of the hybrid dominance of Jeryaks and provide a theoretical basis for further research on the regulatory mechanisms of miRNAs associated with Jeryak muscle growth and development.

Hermetia illucens is a very promising insect due to its ability to convert low-value substrates in highly nutrient feed. Its feeding and nutrition are important issues. This work aimed to study the effect of different substrates composed of coffee silverskin, by-product of the roasting process, enriched with different inclusion of microalgae (5%, 10%, 20%, 25%), Schizochytrium limacinum and Isochrysis galbana, coupled with the assessment of environmental sustainability by LCA. In general, the inclusion of microalgae caused an increase in the growth performance of the larvae, although S. limacinum showed the best results. Higher prepupal weight were observed in larvae fed on 20% and 25% of S. limacinum, shorter development times in larvae fed on 25% of both S. limacinum and I. galbana and higher growth rate were observed in larvae fed on 25% of S. limacinum. Anyway, the inclusion of 10% of S. limacinum showed a small difference with the higher inclusions. Moreover, the 10% of S. limacinum achieved the best waste reduction index. Therefore, considering the greater inclusion of microalgae, the higher the environmental impact of larvae production, the addition of 10% of S. limacinum seems to be the best compromise for the larval rearing.

The relationship between workplace well-being, seniority, workplace bullying, and employee performance was explored in the context of the Mangkutana district office. Data was collected through direct surveys and questionnaires distributed to respondents. The impact of these variables on employee performance was assessed using multiple linear regression analysis. The results unveiled significant insights. Firstly, a positive correlation was observed between favorable workplace well-being factors and employee performance. Feeling valued, supported, and satisfied in the work environment was linked to higher motivation and productivity. Interestingly, seniority exhibited an unexpected negative impact on employee performance. Longer-tenured employees might face complacency or adaptability challenges, leading to decreased performance. Furthermore, the research emphasized the detrimental impacts of workplace bullying on employee performance. Instances of bullying led to the emergence of stress, anxiety, and decreased job satisfaction, collectively leading to a decline in overall performance and well-being. In summation, this study accentuates the significance of fostering a positive work environment that places a premium on employee well-being and concurrently deals with matters related to seniority and workplace bullying. By recognizing and mitigating these factors, organizations can enhance employee performance, productivity, and job satisfaction, fostering a healthier and more successful work environment.

The main aim of this study is to examine the effects of Total Quality Management (TQM) practices (leadership of management, decision making, continuous improvement, customer focus, employee involvement, process management and relations with suppliers) on the financial and operational performance of hospitals in service industry. The data of the study were collected by the questionnaire prepared in the light of published studies and the suggestions of medical and administrative staff. Medical and administrative staff were chosen as target participants that reflect perspectives of hospitals. 1069 questionnaires were answered in 6 private and 26 public hospitals in the Marmara region in Turkey. The results claim that “customer focus” affects both operational performance as well as the financial performance of hospitals more than other TQM practices. While “process management” and “customer focus” explain the variance of financial performance significantly. “Process management” does not explain variance of operational performance.

At present, countries around the world adopt digital strategy, so that enterprises apply digital technology, digital supply chain, blockchain, and a series of digital measures to enhance their competitiveness. By analyzing the relationship between digital transformation of manufacturing export enterprises, and their business performance and export performance, this paper focused on the current situation and existing problems of digital transformation of manufacturing export enterprises in China. Based on the Resource Based View theory and Trade theory, the impact of digital transformation of enterprises performance, proposing hypotheses, and building regression models were explored. With the samples of 1007 listed companies in Shanghai and Shenzhen Stock markets from 2012 to 2019, the regression analysis, intermediate effect test, robustness test, stage lag, and heterogeneity analysis were conducted. The results shew that: (1) Listed manufacturing export enterprises carried out digital transformation, which had a significantly positive effect on enterprise performance; (2) It was found that digital transformation could improve enterprise performance by reducing costs, improving R&amp;D intensity and improving human resources etc. (3) According to the fractal analysis, non-state-owned enterprises had more positive effects on enterprise performance, and digital transformation of manufacturing export enterprises in developed areas had a more significant impact on enterprise performance. Finally, according to the empirical results, relevant suggestions for digital transformation were provided.

Market uncertainty has a significant impact on market performance. Previous studies put much efforts in investigations on market uncertainty related to information asymmetry and risk. However, they have neglected the uncertainty inherent in market transactions, which is also an important aspect of market performance, besides quantity of transactions and market efficiency. In this paper, we put forward the concept of transaction entropy to measure the market uncertainty and see how it changes with price. The definition of transaction entropy is the ratio of total information entropy of all traders to quantity of transactions, reflecting the level of uncertainty in making transactions. And the transaction entropy is the lowest at equilibrium, it will be decreasing in a shortage market, and increasing in a surplus market. Additionally, we make a comparison of total entropy of the centralized market with that of the decentralized market, revealing that the price filtering mechanism could effectively reduce market uncertainty. Overall, the introduction of transaction entropy enriches our understanding of market uncertainty and facilitates a more comprehensive assessment of market performance.

In order to improve the adaptability of broilers to low-temperature environments and their ability to resist acute cold stress (ACS), 240 one-day-old broilers were selected and randomly divided into three groups. The control treatment (CC) was raised at the conventional feeding temperature from 1-43 days (d), the cold stimulation treatments (CS) were kept at 3 °C below the temperature of CC at 1-d intervals for 3 and 6 hours from 15 to 35 d, namely CS3 and CS6, respectively. Then all broilers were kept at 20 °C from 36 to 43 d. ACS was then carried out at 44 d, and the ambient temperature was dropped to 10 °C for 6 hours. The study investigated the production perfor-mance, as well as levels of intestinal barrier genes (including Claudin-1, E-cadherin, Occludin, ZO-1, ZO-2 and Mucin2), secretory IgA in duodenum and jejunum, and immunoglobulins (IgA and IgG) in serum. The results showed that IMCS could increase the daily weight gain and decrease the feed conversion ratio. During the IMCS, the expression levels of intestinal barrier genes were up-regulated and the content of secretory IgA was increased. When IMCS ceased for one week, the level of immunoglobulins in serum stabilized, and the expression levels of Occludin, ZO-2 and Mucin2 still maintained high levels. After ACS, broilers that received IMCS training maintained the high levels of intestinal barrier genes and secretory IgA.

In this paper, the performance and emission characteristics of the engine were investigated with varying ratios of tung oil-based biodiesel blends (B10, B20, and B50) and 0# diesel under different operating conditions. The experimental results indicated that both the power and torque of B10 increased compared with 0# diesel, which increased by 1.9% and 6.6%. But the power and torque of B20 and B50 decreased slightly. The fuel consumption rate increased slightly with an increasing percentage of biodiesel added. In general, the overall emissions of tung oil-based biodiesel blends were lower compared to 0# diesel. Compared to 0# diesel, the CO-specific emissions of B10 decreased by 42.86% at medium and large load, and NOX-specific emissions of tung oil-based biodiesel blends were reduced at all load conditions, except for B50. In addition, HC-specific emissions were all reduced, especially for B20 decreased by 27.54% at 50% load. With the increase of the biodiesel blend ratio, the smoke decreased significantly. Among the blends tested, B50 showed the greatest reduction of 38.05% at 2000 rpm. Overall, it can be asserted that using biodiesel presents a favorable alternative fuel option that can lead to a more environmentally friendly exhaust output.

Indonesia has emerged as one of the leading producers and exporters of palm oil, as supported by data from the Central Bureau of Statistics in 2021, which indicate that Indonesian palm oil exports reached an impressive value of US$ 18.44 billion, or IDR 258 trillion, in 2020, marking an 18.43 percent growth compared to the previous year. Furthermore, the domestic market for palm oil and palm kernel oil remains substantial, despite improvements in export quantities. Various industries, including cooking oil refineries, specialty fats, shortening, margarine, bath soaps, and oleochemicals, present potential markets for palm oil (CPO) and palm kernel oil (PKO). The palm oil industry encompasses four related sub-sectors, namely growers, millers, refiners, and oleochemicals, forming an integrated value chain from upstream to downstream. The current focus on environmental, economic, and social sustainability is driving companies to adopt internal green activities and expand their efforts into sustainability supply chain management (SSCM). Implementing SSCM practices is often seen as economically beneficial, as research has demonstrated their positive impact on firm performance from a resource perspective. Within the palm oil industry, a wide range of green management applications are being utilized. This study aims to examine and highlight the existing sustainable management practices across the entire palm oil supply chain, with a particular emphasis on producing high-quality palm oil. To achieve this objective, the paper utilizes a systematic review methodology, The number of papers analyzed were 62 articles published which involves an extensive review of relevant literature to identify research trends, gaps, and issues. The study seeks to contribute to the body of knowledge by expanding the theory of organizational readiness in preparing globally competitive palm oil products. The research findings hold practical significance for practitioners and academics, providing a comprehensive roadmap for implementing green management applications at the organizational level in the palm oil industry's upstream-to-downstream chain.

Knowledge of body composition is essential for athletes for their sport performance. It has yet to be determined whether differences in body composition are present between international and non-international players playing in the same elite professional club competition. Similarly, it is not yet clear whether differences in body composition according to ethnic origin exist in the elite professional game, where relative homogeneity is to be expected among soccer players. There is no single anthropometric profile that guarantees sporting success, as the somatotype of football players differs according to their individual characteristics. The aim of this study was to assess the description and comparison of the body composition profile of latin american professional football players playing in european leagues. The sample was composed of 238 subjects football players from European professional football leagues. Differences were found in all variables measured. The present study shows that in Latin American professional football players playing in Europe, there are significant differences in different body composition variables such as weight, height, WC, skinfold and fat values. This means that the treatment of these data and the possible classifications of sporting performance carried out in football clubs should be different to other European or African-American football players.

The present study aimed to develop a mathematical model to estimate the performance of an indoor rowing event of 6000m through an 500 m all out test in junior athletes. We selected141 subjects from the Brazilian rowing confederation database (15.9 ± 1.0 years), subsequently randomised the sample to the development (~70%) and cross-validation (~30%) groups of the mathematical model. Performance data for 500m and 6000m were collected (there was a 48h washout between one test and anoth-er).Subsequently, the mathematical model: Time(min) 6000m = { [( Time(s) 500-m * 6) * 2] / 60} + 1.3, was developed by arithmetic modeling using machine learning and Regression analysis, being tested by intraclass correlation coefficient (ICC), Concordance correlation coefficient (CCC), Validity (Cb ), preci-sion (ρ) and bland-Altman plotting. The prediction of the result of 6000m through the mathematical model utilizando apenas o desempenho de 500m “all-out” test showed a significant reliability in de-velopment group (r2 = 0.730, ICC = 0.753; CCC = 0.895, Cb = 0.879, ρ: 0.957, pure error: 0.2 secounds (1.0% estimative error)); and in cross-validation group (r2 = 0.710, ICC = 0.747; CCC = 0.888, Cb = 0.875, ρ: 0.903, pure error: 0.3 secounds (1.4% estimative error)). When comparing the estimated re-sults of the 6000m performance by the mathematical model with the real performance of 6000m per-formed in indoor rowing, no statistical differences were observed. In addition, the mathematical model did not present a significant proportion bias in relation to the 6000 m performance in both groups. The mathematical model for predicting 6000m performance through a 500m fast test was significant for national level junior rowing athletes.

Digital transformation of companies is often referred to as a future track and a strategic path towards ensuring the survival and sustainability of companies. In this paper, we aim to outline this transformation process in Tunisian companies and identify its driving factors and finally explain its key success factors. To this end, we examine a sample of 70 companies operating in all economic sectors. The results indicate that such a digital strategy has a significant and a positive effect on the success of digital transformation of companies. Leadership has an effect at a low level of digital maturity. On the other hand, corporate culture does not have a significant effect on digital transformation. These results contribute to explaining this emerging phenomenon by focusing on the driving factors as well as the factors that contribute to its success.

In this paper, we have investigated the impact of an early learning assessment on students' motivation for improving their performance throughout the semester. An observation analysis was conducted on an entry level mechanical engineering course in which students are enrolled in during their first semester of engineering work. This study analyzes the effect that a first exam, with an average below a passing grade, has on student's outcome in the course. It was hypothesized that students were motivated to achieve their desired grade outcomes following inadequate performance on the first exam. This was investigated by diving into the results of the course and referencing initial performance to the remaining exam and assessment outcomes. Students were placed into grade bands ranging from 0 to 100 in 20% increments. Their results were tracked and it was shown that for the second mechanics exam, averages jumped 43.333%, 35.35%, and 30.055% for grade bands of 0 to 20, 20 to 40, and 40 to 60 respectively. Assessment grades increased as well with the remaining assessments being averaged to a score of 91.095%. Variables contributing to student performance came from both with-in and outside the classroom. Learning communities, material differentiation, and student and professor adaptation all contributed to the rise in performance. It was concluded that the internal and external variables acted in combination with one another to increase student dedication to achieve success.

This short communication reports on the initial results of a much larger, ongoing project, the aim of which is to investigate the question: could the skin microbiome, just like the gut microbiome, play a role in sports recovery and performance – and if so, could this role be as significant a one as that played by the gut microbiome? 17 high performance college athletes addressed their skin microbiome by minimizing contact with synthetic chemicals and by using topical skin supplements, shown previously to significantly increase skin microbiome biodiversity, for two weeks after training. 76% said their skin softness improved, 35% said their muscle stiffness and recovery after sport improved, 12% said their sleep quality improved, and 100% said they would be likely to use skin supplements again. Future work will use hundreds of athletes.

The present paper deals with the investigation, at conceptual level, of the performance of short-medium-range aircraft with hydrogen propulsion. The attention is focused on the relationship between figures of merit related to transport capability, such as passenger capacity and flight range, and the parameters which drive the design of liquid hydrogen tanks and their integration with a given aircraft geometry. The reference aircraft chosen for such purpose is a box-wing short-medium-range airplane, object of study within a previous European research project called PARSIFAL, capable to cut the fuel consumption per passenger-kilometre up to 22%. By adopting a retrofitting approach, non-integral pressure vessels are sized to fit into the fuselage of the reference aircraft, under the assumption that the main aerodynamic, flight mechanic and structural characteristics are not affected. A parametric model is introduced to generate a wide variety of fuselage-tank cross-section layouts, from a single tank with the maximum diameter compatible with a catwalk corridor to multiple tanks located in the cargo deck , and an assessment work-flow is implemented to perform the structural sizing of the tanks and analyse their thermodynamic behaviour during the mission. This latter is simulated with a time-marching approach that couples the fuel request from engines with the thermodynamics of the hydrogen in the tanks, which is constantly subject to evaporation and, depending on the internal pressure, vent-ed-out in gas form. Each model is presented in detail in the paper and results are provided through sensitivity analyses to both the technology parameters of the tanks and the geometric parameters influencing their integration. The guidelines resulting from the analyses indicate that light materials, such as the Aluminium alloy AA2219 for tanks’ structure and polystyrene foam for the insulation, should be selected. Preferred values are also indicted for the aspect ratios of the vessel components, i.e. central tube and endcaps, as well as suggestions for the integration layout to be adopted depending on the desired trade-off between passenger capacity, as for the case of multiple tanks in the cargo deck, and achievable flight ranges, as for the single tank in the section.

The power sectors in most African countries face an enduring problem of utility performance – electricity utilities have failed to deliver adequate, reliable and competitively priced electricity to support economic growth and improve the welfare of their populations. Despite more than two decades of power sector re-forms, outcomes have been varied and often disappointing. Using a case study de-sign, we explore the five key enduring power challenges. The research utilizes a more powerful analytical framework that combines power sector reform theory and principal-agent theoretical lens to explore the experience of power sector reforms in Kenya and provides a deeper understanding of drivers of utility performance and reform impacts. Empirical findings show that the structural, governance and regulatory reforms that previously created incentives for improved utility performance are increasingly threatened by political influence. Kenya Power’s financial viability has deteriorated in recent years and the regulator has been undermined. One of our major conclusions is that when the relationship between the principal (government) and agent (utility) is well understood and the agent is properly incentivized, performance improvements are possible. However, when the government undermines or muddies those incentives through conflicting political interventions, performance improvements can be reversed.

Understanding how species that follow different life-history strategies respond to stressful temperature can be essential to efficient treatments against agricultural pests. Here we focus on how the development and reproduction of C. medinalis is influenced by exposure to different rearing temperatures in the immature stage. We found that low (18 or 22 °C) or high (30 and 34 °C) rearing temperatures negatively affected the immature development and flight performance compared to the normal temperature 26 °C, with higher larval and pupal mortality, lower pupation and eclosion rates and shorter flight duration and distance. Low rearing temperatures significantly slowed down the immature process, but accelerated adult reproduction. However, high rearing temperatures had the opposite impacts. Interestingly, the flight of adults with un-mature rearing low temperatures (18 and 22 °C) significantly decreased their lifetime fecundity and mating frequency, but increased pre-oviposition period of females compared to the control; On contrast, high rearing temperatures (30 and 34 °C) significantly accelerated onset of oviposition and enhanced synchrony of spawning. These results indicate high rearing temperatures in the immature stage are more likely to trigger the onset of migration, but low rearing temperatures induces adults to have a greater resident propensity with stronger reproductive ability.

: Supplement the use of ergogenic aids in cyclist’s directly have been improved the body metabolism and hemodynamic factors that are micro supplement in chancing reactions on the body muscle mass and limb muscle. Mostly knowing that, muscle power development progressive fast glycolytic and short time oxidative systems reactions. Sport competition intervals, therefore, during periods has been used specific drinks supported to cyclists. But, be obtained during should be long race times. Athletes directly needed some drug and fluid intake to prevented from metabolic breakdown rapidly the dynamic physiologic performance factors. Beta-alanine supplementation can be direct muscle performance development affects the anaerobic metabolism and capacity. It should be de-termined how the cyclists will use the competitive and training period intervals can increase the cyclists specific sprint and endurance race performance. Science cyclist International Road doses will be created in which, intervals can random effectively the investigate. This study random a cohort studies is examined the effects of beta-alanine supplementation on aerobic and anaerobic power output in specific cyclists. Therefore, we have been databases PubMed, Scopus and Medline initial search 10 August 2020 were created prospective effect the quality of bias work concluded effect size (ES) 95% confidence interval (CI) were used in participant. Participations (N=66) have age range 25 to 38 of the using beta-alanine in training periods to endurance muscle performance, aerobic power, anaerobic power, and sprint time trials. As a result of beta-alanine improved an-aerobic and aerobic power output on 4-week time-dependent trial performance condition. Signifi-cant values are obtained level factor alpha <0.05 and p-value analysis pre-post interactive stand-ardization.

The exposure to extreme temperatures in workplaces involves physical hazards for workers. A poorly acclimated worker may have lower performance and vigilance and may therefore be more exposed to accidents and injuries. Due to the incompatibility of the existing standards implemented in some workplaces and the lack of thermoregulation in many protective equipment, thermal stress remains one of the most frequent physical hazards in many work sectors. However, many of these problems can be overcome with the use of smart textile technologies that enable intelligent thermoregulation in personal protective equipment. Smart textiles can detect, react and adapt to many external stimuli. Interconnected sensors and actuators that interact and react to existing risks can provide the wearer with increased safety, protection and comfort. Thus, the skills of smart protective equipment can contribute to the reduction of errors and the number and severity of accidents in the workplace, and thus promote improved performance, efficiency and productivity.This review provides an overview and opinions of authors on the current state of knowledge on these types of technologies by reviewing and discussing the state of the art of commercially available systems and the advances made in previous research works.

The purpose of this study was to see how dietary supplementation with phenylpyruvate affected broiler chicken growth, slaughter performance, gut health microbiota, and immunity. A total of 288 day old broiler chickens were randomly assigned to one of four groups (6 replicates each with 12 chicken). NC (basal diet), PC (basal diet plus antibiotic virginiamycin 15ppm), LCP and HCP (basal diet plus phenylpyruvate 1kg/t and 2kg/t, respectively). Results showed that PC had higher ADFI during the first 21 days, and better FCR than the NC, the LCP and HCP also improved broilers’ FCR 0.001 and 0.037% in relation to NC respectively. HCP has a higher all-eviscerated ratio than NC and less abdominal fat than LCP. HCP has increased villus length and crypt depth in the ileum compared to the NC. Bursa was lower in HCP and thymus was lower in LCP and PC. In contrast HCP have lower pro-inflammatory cytokine IL-1, as well as lower TLR4. The phenylpyruvate improved family Selenomonadaceae, genus Megamonas Bacteroides species that are known for beneficial effects like for maintenance of the cell surface structure, regulating aromatic amino acids and C. jejuni-suppressive treatment respectively. Finally, phenylpyruvate feed supplement can be utilized to improve growth performance and positively modulate gut microbiota, however this is less efficient than antibiotics in improving growth performance, although more efficient in improving productive performance and gut morphology. Moreover, high dose of phenylpyruvate is more effective than low dose

Legacy IPv4 networks are strenuous to manage and operate. Network operators are in need to minimize the capital and operational expenditure of running network infrastructure. The implementation of Software-defined networking (SDN) addresses those issues by minimizing the expenditures in the long run. Legacy networks need to integrate with the SDN networks for the smooth migration towards the fully functional SDN environment. In this paper, we compare the network performance of the legacy network with the SDN network for IP routing in order to determine the feasibility of the SDN deployment in the Internet Service provider (ISP) network. The simulation of the network is performed in the Mininet test-bed and the network traffic is generated using distributed Internet traffic generator. Open network operating system is used as a controller for the SDN network in which SDN-IP application is used for IP routing. Round trip time, bandwidth, and packet transmission rate from both SDN and legacy networks are first collected and then the comparison is done. We found that SDN-IP performs better in terms of bandwidth and latency as compared to legacy routing. The experimental analysis of interoperability between SDN and legacy networks shows that SDN implementation in production level carrier-grade ISP network is viable and progressive.

Biodiesel has caught the attention of many researchers because it has great potential to be sustainable fossil fuel substitute. Biodiesel has non-toxic and renewable nature and has been proven to emit less amount of environmentally harmful emissions such as hydrocarbons (HC), and carbon monoxide (CO), as well as smoke particles during combustion. Problems related to global warming caused by greenhouse gas (GHG) emissions could also be solved by utilizing biodiesel as a daily energy source. However, the expensive cost of biodiesel production, mainly because of the cost of natural feedstock, holds the potential of biodiesel commercialization. The selection of natural sources of biodiesel should be made with observations from economic, agricultural, and technical perspectives to obtain one feasible biodiesel with superior characteristics. This review paper presents a detailed overview of various natural sources, their physicochemical properties, as well as the performance, emission, and combustion characteristics of biodiesel when used in a diesel engine. The recent progress in studies about natural feedstocks and manufacturing methods used in biodiesel production were evaluated in detail. Finally, the findings of the present work reveal that transesterification is currently the most superior and commonly used biodiesel production method compared to other methods available.

The aim of this article was to examine if there are position-specific differences in the morphological characteristics of sub-elite female football players and to establish normative standards for this level of female football players. The morphological features of 101 sub-elite female football players (age: 21.8±2.7 years) were assessed. Twenty anthropometric sites were used in the measurements of body composition and somatotype. The average value of body fat percentage was 20.8±5.7%. The somatotype of the overall group was 4.0–2.4–2.1. Positional significant (p ≤ 0.05) differences were found between goalkeepers and outfield players in morphological characteristics. Goalkeepers were taller, heavier, possessed the highest body fat percentage and showed higher values for all skinfolds, breadth, girth and length measurements. However, there were very few practically worthwhile differences between the outfield positions. Positional groups did not differ (p ≤ 0.05) in somatotype characteristics either. The study suggests that at sub-elite level there are mainly differences between goalkeepers and outfield players, but outfield players are homogeneous when comparing morphological characteristics. These results may serve as normative values for future comparisons regarding the morphological characteristics of female football players.

The present study examines the effect of SiO2 nano-additives on the performance and emission characteristics of a diesel engine fuelled with soybean biodiesel. Soybean biofuel was prepared using the transesterification process. Nano-additives characterisations were done using different tests such as FESEM, XRD, EDS, etc., to study the morphology of nano-additives. For proper blending of nano-additives with biodiesel, the ultrasonication process was used. Surfactant was used for the stabilisation of nano-additives. After making all the combinations of nano fuel blends, physicochemical properties were measured as per ASTM standards. Performance and emissions readings were taken at different load conditions. It was found that with the addition of SiO2 nano-additives, brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) was increased by 3.48-6.39% and 5.81-9.88%, respectively. Significant reduction of CO, CO2, NOx, and smoke emissions were also observed compared to baseline fule due to better combustion efficiency with the use of SiO2 nano-additive.

Background: The treatment plan of prosthetic restorations supported by dental implants require comprehensive scientific knowledge to deliver prostheses with good prognosis, even before the implant insertion. This review aims to analyze the main prosthetic determinants of the prognosis of implant-supported prostheses. Methods: A systematic review of the literature was conducted with a PICO question: "For partially or complete edentulous subjects treated with implant-supported prostheses, which prosthetic factors could affect clinical outcomes?". A literature search was performed electronically in PubMed (MEDLINE), Scopus and Cochrane Library with the following equation [PROGNOS* OR RISK] FACTOR IMPLANT DENTAL, and by hand search in relevant journals and throughout the selected papers. Results: This revision was carried out based on 50 papers focused on several prosthodontics-related risk factors that were grouped as follows: implant-connection, loading protocol, transmucosal abutments, prosthetic fit, provisionalization, type of retention, impression technique, fabrication technique, and occlusion. More than a half of the studies were systematic reviews (30%), meta-analysis (16%) or prospective evaluations of prosthesis with various kinds of events (18%). But also narrative reviews of literature (14%) and in vitro/animal studies (16%) were found. Conclusions: The current literature provides insufficient evidence for most of the investigated topics. However, based on the accumulated data, it seems reasonable to defend that the best treatment approach is the use of morse taper implants with transmucosal abutments, recorded by means of rigidly splinted copings through the pick-up technique, and screwed by milled prosthesis occlusally adjusted to minimize functional overloading.

The expression microarray technique was performed to investigate the differences in gene expression between Czech Large White pigs and wild boars in the longissimus lumborum et thoracis and biceps femoris muscle tissues. The NREP gene (neuronal regeneration related protein homolog) was selected for detailed study as an expressional and functional candidate gene. NREP plays a role in the transformation of neural, muscle and fibroblast cells and in smooth muscle myogenesis. Quantitative real-time PCR results confirmed that the porcine NREP gene was expressed in both skeletal muscles and significantly overexpressed in Czech Large White pigs compared to wild boars (P &lt; 0.05). We identified 9 polymorphic sites in genomic DNA of NREP gene. Six of these polymorphisms were in complete linkage disequilibrium and therefore only 4 polymorphisms were informative. Associations of these 4 polymorphisms (HF571253:g.103G&gt;A, HF571253:g.134G&gt;A, HF571253:g.179T&gt;C and HF571253:g.402_409delT) with meat performance traits were assessed in Czech Large White pigs. New polymorphisms in NREP gene were significantly associated with parameters of daily weight gain, lean meat and backfat thickness in Czech Large White pigs. Our primary study suggested that porcine NREP may play an important role in skeletal muscle growth, fat metabolism and meat performance traits.

Despite the increase in popularity of Zero Waste (ZW) concept, the successful implementation of this concept in waste management is still facing many challenges. The plastic recycling rate in Australia is currently only about 9.4%, which could leave up to 90.6% of plastic consumption being sent to landfills. The state of Victoria (in Australia) has proposed an ambitious plan to upgrade its waste and recycling system and to divert about 80% of waste from landfills by 2030. The aim of this research is to study Victoria’s current waste management plan and to develop a simulation model to assess the feasibility of it achieving zero plastic waste by 2035. In this direction, a fundamental knowledge of global ZW implementation needs to be acquired in order to understand the challenges, obstacles, and uncertainties in achieving ZW target. A simulation model is established using a method called double baselines. This method was developed as an improvisation to address the limitation of data availability for the model development. The model will run on 4 scenarios including one from Victoria’s current plan. Outcomes from the model are produced in comparative charts covering 6 key considerations including the rates of plastic consumption, waste to landfill, diversion, recycling, relative accumulative cost and effort. The findings of this study pointed out that Victoria’s current plan are feasible for its goal and presented with opportunities for improvement especially towards zero plastic waste. Besides, study results also reveal that the Victoria’s current plan to achieve 80% diversion rate by 2030 is possible but the zero plastic waste target by 2035 is less likely to happen.

During the last twenty years around the world there has been a rapid increase in the number of people visiting long established religious shrines as well as the creation of new sites by those operating outside the boundaries of institutional religion. This increase is intimately associated with the revival of traditional routes, the creation of new ones and the invention of new rituals (religious, spiritual and secular). To examine this process I will focus on the European region and two contrasting destinations in particular – the Catholic shrine of Lourdes, France, and the pre-Christian shrine of Avebury, England – drawing on my personal involvement in travelling to both destinations and being involved in ritual activities along the route and at the two destinations. In the discussion section of the paper I will explore the relevance of these two case studies to the analysis of power, agency and performance and the ways in which they expose (a) the role of institutions and entrepreneurs in creating rituals and sacred places and (b) the relationship between people and the domesticated landscape.

This paper deals with the service performance analysis and improvement using discrete event simulation has been used. The simulation of the heath care has been done by arena master development 14-version software. The performance measurement for this study are patients output, service rate, service efficiency and it is directly related to waiting time of patients in each service station, work in progress, resource utilization.Simulation model was building for Bahir Dar clinic and then, prepared the proposed model for the system. Based on the simulation model run result, the output of the existing healthcare service system is low due to presence of bottlenecks on the service system. Moreover, the station with the largest queue and high resource utilization are identified as a bottleneck. The bottlenecks, which have identified are reduced by using reassigning the existing resources and add new resources and merging the similar services, which has under low resource utilization (nurses). Finally, the researchers have proposed a developed model from different scenarios. Moreover, the best scenario is developed by combining scenario 2 and 3. And then, service efficiency of the healthcare has increased by 9.86 percent, the work in progress (WIP) are reduced by 3 patients from the system and the service capacity of the system is increased 34 to 40 patients per day due to the reduction of bottleneck stations.

Motivated by Autonomous vehicle idea and driving safety issues, driver assistance system such as Active braking, Cruise Control, Lane departure warning lane keeping and etc. has become a very active research area. However, this paper presents the performance and robustness analysis of a model predictive control and proportional integral derivative control for lane keeping maneuvers of an autonomous vehicle using computer vision simulation studies. A simulation study was carried out where a vehicle model based on single tracked bicycle model was developed in MATLAB/SIMULINK environment together with a vision dynamic system. Both PID controller and MPC were simulated to maintain the desired reference trajectory of the vehicle by controlling steering angle. Further performance and robustness analysis were carried out and the simulation results show that the proposed control system for the PID control achieved its objective even though it was less robust in maintaining its performance under various conditions like vehicle load change, different longitudinal speed and different cornering stiffness. While in the case of MPC the optimizer made sure that the predicted future trajectory of the vehicle output tracks the desired reference trajectory and was more robust in maintaining its performance under same conditions as in PID.

This study aims to examines three elements shape leadership in Leader-Member Exchange (LMX) theory as a relationship and process. LMX quality is important for the company, because it relates to employee behavior and attitudes, including improving employee performance. The research method applied literature review using description logic and systematics. In this article the theory will be observed specially the effect of LMX on employee performance and antecedents of LMX. The results of the study found that the effect of LMX quality on performance is determined by the characteristics of the task as antecedent LMX in the company.

This study examines the effect of market risk on the financial performance of 31 non-financial companies listed on the Casablanca Stock Exchange (CSE) over the period 2000-2016. We utilize three alternative variables to assess financial performance, namely return on assets, return on equity and profit margin. Next, we use the degree of financial leverage, the book-to-market ratio, and the gearing ratio as market risk variables. Besides, we employ the pooled OLS model, the fixed effects model, the random-effects model, the difference GMM and the system GMM models. The results show that market risk indicators have a negative and significant influence on the companies' financial performance. The elasticities are greater following the book-to-market ratio compared to the degree of financial leverage and the gearing ratio, respectively. In most cases, the firm size, the tangibility ratio, and the cash holdings ratio have a positive effect on financial performance, whereas the firms' age, the debt-to-income ratio, stock turnover, and leverage hurt the performance of these non-financial companies. Therefore, decision-makers and managers should mitigate market risk through appropriate strategies of risk management, such as derivatives and insurance techniques.

In this study, a full-scale pilot testing was performed with side-by-side operation of a conventional enhanced biological phosphorus removal (EBPR) process and a side-stream EBPR (S2EBPR) process. A comparison of the performance, activities and population dynamics of key functionally relevant populations between the two configurations were carried out. The results demonstrated that, with the same influent wastewater characteristics, S2EBPR configuration showed more effective and stable orthophosphate (PO₄-P) removal performance (up to 94% with average effluent concentration down to 0.1 mg P/L) than conventional EBPR, especially when the mixers in side-stream reactor were operated intermittently. Mass balance analysis illustrated that both denitrification and EBPR performance have been enhanced in S2EBPR configuration through diverting primary effluent to anoxic zone and producing additional carbon (~40%) via fermentation in side-stream reactor. Microbial characterization showed that there was no significant difference in the relative abundances of Ca. Accumulibacter (~5.9%) and Tetrasphaera (~16%) putative polyphosphate-accumulating organisms (PAOs) between the two configurations. However, lower relative abundance of known GAOs was observed in S2EBPR configuration (1.1%) than the conventional one (2.7%). A relatively higher PAO activity and increased degree of dependence on glycolysis pathway than TCA cycle was observed in S2EBPR configuration using P release and uptake batch test. Adequate anaerobic solid retention time (SRT) and conditions that generate continuous and slow feeding/production of volatile fatty acid (VFA) with higher composition percentage of propionate in the side-stream reactor of S2EBPR process likely provide a competitive advantage for PAOs over GAOs.

The heat values of waste mineral oils are equal to the heat value of the fuel oil. However, heat value alone is not sufficient for the use of waste mineral oils. as fuel. However, the critical physical properties of fuels such as density and viscosity need to be adapted to the system in order to be used. In this study, the engine oils used in the first 10,000 km of the vehicles were used as waste mineral oil. An organic-based Mn additive was synthesized to improve the properties of the waste mineral oil. It was observed that mixing the Mn additive with the waste mineral oil at different doses (4, 8, 12 and 16 ppm) improves the viscosity of the waste oil and the flash point. The resulting fuel was evaluated for emission using different loads in a 5 kW capacity generator to compare the fuel with standard diesel fuel and to determine the effect of Mn addition. In the experimental study, it was observed that the emission characteristics of the fuel obtained from waste mineral oil were worse than diesel fuel, but some improvement with Mn addition. As a result, we found that the use of waste mineral oils in engines in fuel standards was not appropriate, but may be improved with additives.

Full-scale wind turbine technology has been widely developing in the recent years and condition monitoring techniques assist at the scope of making 100\% technical availability a realistic perspective. In this context, several retrofitting techniques are being used for further improving the efficiency of wind kinetic energy conversion. This kind of interventions is costly and, furthermore, the estimation of the energy enhancement is commonly provided under the hypothesis of ideal conditions, as for example absence of wakes between nearby turbines. A precise quantification of the energy gained by retrofitting is therefore precious in real conditions, that can be very different from ideal ones. In this work, three kinds of retrofitting are studied through the operational data of test case wind farms: improved start-up through pitch angle adjustment near the cut-in, aerodynamic blade retrofitting by means of vortex generators and passive flow control devices, extension of the power curve by raising cut-out and high wind speed cut-in. SCADA data are employed and reliable methods are formulated for estimating the energy improvement from each of the above retrofitting. Further, an insight is provided about wind turbine functioning under very stressing regimes, as for example high wind speeds.

Biofilter application for treatment of stormwater containing de-icing chemicals commonly applied in airports, propylene glycol and potassium formate, was investigated. Lab-scale adsorption tests using filter media made of crushed clay (Filtralite) and granular activated carbon showed that adsorption was unsuitable for removal of propylene glycol and potassium formate. Column filtration experiment testing two different crushed clay size ranges was conducted. The results showed that DOC removal was dependent on a number of factors. This study investigated the impact of filter depth, nutrients addition, and filtration rate. DOC removal suggested that DOC degradation occurred on the top filter layer. It was shown that the most active separation occurred in the first ~20 cm of filter depth. This was confirmed by results from water quality analysis (i.e. DOC removal and ATP measurement) and calculations based on a filtration performance analysis (Iwasaki model) and filter hydraulic evaluation (Lindquist diagram). It was shown that for the highest C:N:P ratio tested (molar ratio of 24:7:1), 50-60% DOC removal was achieved. Addition of nutrients was found important and determining the biofilter performance.

The study aims to analyze the performance criteria of the GR4J model to reproduce high water flows in the Ouémé watershed at Bonou's outlet which has been vulnerable to climate change in recent decades. The methodology focused on the use of daily climatological and hydrometric data extracted from files of National Directorate of Meteorology, and General Directorate of Water; they were supplemented by those of SIEREM/HSM dataset over the period 1961-2015. The rainfall was regionalized using Thiessen method. The performance of the GR4J model was assessed with NSE, RMSE and KGE criteria. The results indicate that the study area is marked by rainfall variabilities and detection of two breakpoints (1968 and 1987) which divide the series into three sub-periods; these discontinuities have repercussions on the streamflow. It's found that GR4J model overestimates the streamflow during the low water period and underestimates them in high water. However, the efficiency and performance criteria NSE, RMSE and KGE calculated on high water flow rates are better in calibration than in validation. The KGE values are range between 83-85% in calibration and 56-68% during validation, which gives to GR4J model the efficiency and performance to reproduce high flow rates in the study area

While providing safe water for the rural poor is considered a basic human right, there are numerous issues associated with existing technologies with shortcomings. Performance issues have continued to fail to meet the needs of impoverished families due to issues including high cost, difficulties with performance, and continuing needs for maintenance. These issues have severely interfered the safe water accessibility. Key aspects of the Guelph Water Filter (GWF) system can avoid/minimize many of these issues. The GWF as described herein enables delivery of low cost, long-term performance at 3Log removal of E.coli and can deliver 1 to 3 L of treated water per hour. The GWF is simple to operate, has an ability to provide sufficient water for a family, maintains longevity of performance, is easy to maintain and has protection against breakage during the cleaning process, is repairable at village level, and operates using a sizable reservoir of water to supply raw water, meaning the technology does not need to be refilled frequently. Hence, the capability of the novel GWF technology is shown to bypass many of the troublesome features of alternative low-tech water treatment technologies. The potential for the GWF to function for 2 days continuously avoids the need for young girls to fetch raw water frequently during a day, thereby enabling them to attend school. Hence, the GWF enhances the potential to result in ‘safe water and full schools’, providing the opportunity for girls to receive education and capture socio-economic benefits for the community.

A novel concept of ion separation Anisotropic Diffusion Mobility Analyser (ADMA) with Individual Ion Counter (IIC) was shown by numerical modelling to be able to separate ions with high resolution and ultra-high sensitivity. An ADMA-IIC device has been developed and tested at sheath flow rates below 40 l/min with a number of chemicals relevant to airport security and military applications. The resolving power of the ADMA was observed to be in the range of 40 to 80. These data were close to the resolution obtained in numerical modelling predictions. It is greater than or comparable with the RP of currently available on-the-market devices for airport security and other applications. It was also confirmed that the ADMA technology enables very fast detection of analytes, at least 100 times faster than ion mobility spectrometers. It was shown that Brownian diffusion can be controlled and even overpowered by generating highly anisotropic diffusion in the ADMA device. The ultimate sensitivity of single-ion detection below the ppq range has been demonstrated.

In the rapidly evolving landscape of wireless communication, each successive generation of networks has achieved significant technological leaps, profoundly transforming the way we connect and interact. From the analog simplicity of 1G to the digital prowess of 5G, the journey of mobile networks has been marked by constant innovation and escalating demands for faster, more reliable, and more efficient communication systems. As 5G becomes a global reality, laying the foundation for an interconnected world, the quest for even more advanced networks leads us to the threshold of the sixth-generation (6G) era. This paper presents a hierarchical exploration of 6G networks, poised at the forefront of the next revolution in mobile wireless technology. This study delves into the technological advancements that underpin the need for 6G, examining its key features, benefits, and the key enabling technologies. We dissect the intricacies of cutting-edge innovations like terahertz communication, ultra-massive MIMO, artificial intelligence (AI), machine learning, quantum communication, and re-configurable intelligent surfaces. Through a meticulous analysis, we evaluate the strengths, weaknesses, and state-of-the-art research in these areas, offering a wider view of the current progress and potential applications of 6G networks. Central to our discussion is the transformative role of AI in shaping the future of 6G networks. By integrating AI and machine learning, 6G networks are expected to offer unprecedented capabilities, from enhanced mobile broadband to groundbreaking applications in areas like smart cities and autonomous systems. This integration heralds a new era of intelligent, self-optimizing networks that promise to redefine the parameters of connectivity and digital interaction. This paper also addresses critical challenges in the deployment of 6G, from technological hurdles to regulatory concerns, providing a holistic assessment of potential barriers. By highlighting the interplay between 6G and AI technologies, this study not only maps out the current landscape but also lights the path forward in this rapidly evolving domain. This paper aims to be a cornerstone resource, providing essential insights, addressing unresolved research questions, and stimulating further investigation into the multifaceted realm of 6G networks. By highlighting the synergy between 6G and AI(Artificial Intelligence) technologies, we aim to illuminate the path forward in this rapidly evolving field.

Age-related Macular Degeneration (AMD) is the major cause of elders’ vision loss, early screening and treatment are the most efficient way to reduce the rate of blindness. AI-based methods based on ophthalmic images play great potential for AMD diagnosis. However, low levels of accuracy, robustness, and explainability are challenges for AI approaches applied in clinics. Thus, this study proposed a multi-type of data source fusion method and a multi-model fusion approach for AMD detection. Typical unsupervised (Hierarchical Clustering and K-Means), typical supervised (SVM, VGG-16, and ResNet) methods, and proposed methods (multi-source data fusion-based method and multi-model fusion-based approach) are compared based on Optical Coherence Tomography (OCT), Fundus Autofluorescence (FAF), regular color fundus photography (CFP) and Ultra-Wide field Fundus (UWF) images. Data preprocessing and enhancements of each type of data are discussed. A feature extraction based on unsupervised ML models, feature combination and normalization, and multi-layer perception (MLP) algorithm are involved in the proposed multi-source data fusion-based method. Supervised ML and DL models and a voting mechanism are involved in the multi-model fusion-based approach. Findings show that the proposed methods present a high performance of accuracy and robustness. A real-world UWF database is involved from Shenzhen Aier Hospital. Practical and theoretical contributions are delivered. A reference value for medical diagnosis based on multiple digital images is contributed.

Laser energy per unit surface, necessary to trigger the material removal, decreases with the pulse shortening becoming the pulse-time independent in the sub-picosecond range. These pulses are shorter the electron-to-ion energy transfer time and electronic heat conduction time minimizing the energy losses. The electrons receiving the energy larger than the threshold, drag the ions off the surface in the mode of electrostatic ablation. We show that the pulse shorter than the ion period (Shorter-the-Limit (StL)) ejects conduction electrons with the energy larger than the work function (from a metal) leaving the bare ions immobile in a few atomic layers. The electrons emission is followed by the bare ion’s explosion, ablation, and THz radiation from expanding plasma. We compare this phenomenon to the classic photo effect, nanocluster Coulomb explosions, show differences and consider possibilities for detecting the new mode of ablation experimentally by emitted THz radiation and consider applications of high-precision nano-machining with this low intensity irradiation.

The prediction of wind power output is part of the basic work of power grid dispatching and energy distribution. At present, the output power prediction is mainly obtained by fitting and regressing the historical data. The medium- and long-term power prediction results exhibit large deviations due to the uncertainty of wind power generation. In order to meet the demand for accessing large-scale wind power into the electricity grid and to further improve the accuracy of short-term wind power prediction, it is necessary to develop models for accurate and precise short-term wind power prediction based on advanced algorithms for studying the output power of a wind power generation system. This paper summarizes the contribution of the current advanced wind power forecasting technology and delineates the key advantages and disadvantages of various wind power forecasting models. These models have different forecasting capabilities, update the weights of each model in real time, improve the comprehensive forecasting capability of the model, and have good application prospects in wind power generation forecasting. Furthermore, the case studies and examples in the literature for accurately predicting ultra-short-term and short-term wind power generation with uncertainty and randomness are reviewed and analyzed. Finally, we present prospects for future studies that can serve as useful directions for other researchers planning to conduct similar experiments and investigations.

High-grade advanced ovarian, fallopian tube and primary peritoneal (HGAOC) cancer are malignancies in which, apart from surgical treatment, systemic treatment plays an important role. The improvement in treatment results is associated with the introduction of polyADP-ribose polymerase inhibitors (PARPis). The aim of this study is to present a cross-section of patients treated for HGAOC, in one center, including the distribution of treatment principles following the most up-to-date guidelines. We observed patients who reported to the Department of Gyneacological Oncology between January 2018 and December 2023. We analyzed 437 women with a first diagnosis of HGAOC, who had not been treated before. The introduction of combined treatment with bevacizumab and PARPi into the first line of treatment, regardless of any remnants left during cytoreductive surgery, was introduced in November 2022. Since then, 30% (18/60) of patients (14 with olaparib and 4 with niraparib) have used the above regimen. Previously, in May 2021 - October 2022, it was 27% of patients (13/81 with olaparib and 9/81 with niraparib). Among patients starting treatment in January 2018 - April 2021, only 4.7% (5/106) received the platinum + paclitaxel + olaparib regimen. In both groups – with and without BRCA1/2 pathogenic or likely- pathogenic variant, significantly more patients used PC + PARPi or PC + BEV + PARPi in periods II and III than in period I (p<0.01). The introduction of modern treatment in our center very quickly changed the structure of patient treatment. Carriers of BRCA1/2 pathogenic or likely-pathogenic variant had previously received only chemotherapy, disappeared after the introduction of PARPi, in favor of new therapies. Most patients with no BRCA1/2 pathogenic or likely-pathogenic variant, who used PARPi in therapy in our center – received niraparib and therefore they are beneficiaries of molecular diagnostics in the field of HRD.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

Measuring cell confluence in high-throughput screening of pharmaceutics, cell culture monitoring, cancer research, and industrial applications requires quantitative and standardizable measures to minimize subjective observations and increase throughput1-12 . Over the past half-century, non-invasive specialized programs have been created to quantitatively assess cell confluence, and some software tools exist to meet these needs1,4,5,6,7,8,9 . However, many of these tools are expensive, computationally-demanding, or inaccessible to non-experts1,6. With the assistance of generative artificial intelligence, we have developed the Confluence Analysis Program (CAP), a modern tool designed to be precise, interactive, and user-friendly. CAP is written entirely in Python and runs in any command-line interface (CLI), including Terminal (OS) and Command Prompt (Windows). In addition to fetching all necessary external libraries automatically and prompting drag-and-drop image retrieval, CAP features live visual comparison of cell mass identification to the original image assay. Our results demonstrate robust performance of CAP on fluorescent micrographs of varying confluences ranging from low to high. CAP is provided as a free resource, accessible in the Supplementary Materials.

Glioblastoma is a highly aggressive brain tumor and is considered to be the most common primary one. Recurrence after treatment is a major problem. The recurrence of GBM is related to different cellular mechanisms and molecular signaling. Therapies to prolong survival are not completely effective. Epigenetics and non-coding genetic elements play a crucial role in gliomagenesis. Non-coding RNAs are novel regulatory RNAs that play key roles in different physiological processes such as gene regulation, cell differentiation, and proliferation. Interestingly, some LncRNAs have a tumor suppressor role while others are oncogenic. In this review article, we are going to illustrate the role of a well-known lncRNA HOX transcript antisense intergenic RNA (HOTAIR) in glioma and highlight the possible functions in glioma in both pre-clinical and clinically evident studies.

In this letter, we propose a pattern-diversity antenna with different radiation patterns at two different frequency bands (f1 and f2) (f1: broadside radiation pattern, f2: conical radiation pattern). The proposed structure consists of a central circular antenna and two annular ring antennas; each of the three antennas has individual ports. Two of the ports exhibit orthogonal broadside radiation patterns; the other two ports exhibit orthogonal conical radiation patterns. Thus, they have polarization diversity characteristics. To improve isolation between ports, the inner part of the annular ring antennas is shorted via array, and the outermost port is positioned orthogonal to the other ports. Using this configuration, the isolation between ports was measured as -26.7 dB and -30.1 dB at the two frequency bands, respectively. Experimental results based on the fabricated prototype show that the proposed antenna achieves -10 dB bandwidths of 240 MHz (5.71~5.95 GHz) and 210 MHz (7.69~7.9 GHz) at f1 and f2, respectively.

Background: Glioma surgery was remarkably renewed in the past 2 decades, with improved safety and limited but yet improved life expectations. Fluorescence-guided resection of high-grade gliomas (HGG) plays a central role in this sense, by allowing higher degrees of extent of resection (EOR). The introduction of the exoscopic guided surgery may be considered an implementation for fluorescence techniques over the traditional microscopes. We present the application and the advantages of the exoscopic guided surgery compared to the microscopic surgery in tumor resection guided by 5-ALA fluorescence in patients with HGG. Methods: ten consecutive patients underwent a surgery for HGG resection. The surgery was performed via an exoscopic-guided procedure (Olympus Orbeye) and after oral administration of Gliolan 5 hours before the procedure. During surgery, the procedure was shifted to microscope (Kinevo 900, Zeiss) view. The intensity of the fluorescence under the two different was subjectively measured in different picture samples during the surgery in a 1 to 5 (from minimum to maximum) scale. The brightness of the surgical field and the detailing of the anatomy were also analyzed comparatively. Results: among the ten patients the histopathological diagnosis was an high grade glioma in all cases. In 9 cases was possible to achieve the gross total resection. There was no perioperative mortality. The median fluorescence intensity, on a scale of 1–5, was 4.5 in the exoscope group and 3.5 in the microscope group (p<0.01). Conclusions: The exoscopic guided surgery adds advantages to the traditional fluorescence- guided surgery with 5-aminolevulinic acid. Beyond the important advantage of low cost and the possibility to perform collaborative surgeries, it adds a plain and continuous visualization of the tumor and the surgical field in the fluorescence guided glioma surgery compared to the microscopic guided one.

Since the implementation of the Materials Genome Project by the Obama administration in the United States, the development of various computational materials databases has fundamentally expanded the choices of industries such as materials and energy. In the field of thermoelectric materials, the thermoelectric figure of merit ZT quantifies the performance of the material. From the viewpoint of calculations for vast materials, the ZT values are not easily obtained due to their computational complexity. Here, we show how to build a database of thermoelectric materials based on first-principles calculations for the electronic and heat transport of materials. Firstly, the initial structures are classified according to the values of bandgap and other basic properties using the clustering algorithm K-means in machine learning, and high-throughput first principles calculations are carried out for narrow-bandgap semiconductors which exhibiting potential thermoelectric application. The present framework of calculations mainly includes deformation potential module, electrical transport performance module, mechanical and thermodynamic properties module. We have also set up a search webpage for the calculated database of thermoelectric materials, providing searching and viewing the related physical properties of materials. Our work may inspire the construction of more computational databases of first-principle thermoelectric materials and accelerate research progress in the field of thermoelectrics.

Background: Annual influenza epidemics are a serious public health problem, causing particularly severe morbidity and mortality in high-risk groups. The study aimed to understand Poles' attitudes and beliefs towards influenza vaccinations in the flu season of 2022–2023, analyze preferences and unmet needs regarding influenza vaccinations, and examine the perception and acceptance of the influenza vaccine among individuals at risk of flu complications. Methods: A cross-sectional survey-based study was carried out on a sample of 1446 respondents. The Google Forms questionnaire was created and disseminated electronically using social media and e-mail. The pre-test was performed at the beginning of the project. Results: The majority of respondents (71%) could identify "high-risk groups" recommended for influenza vaccination. Furthermore, it was observed that individuals aged 21 to 59 demonstrated a higher level of knowledge in this regard compared to those below 20 and above 65 years old, and individuals with higher and medium education levels were much better at identifying risk groups for influenza virus infection. The majority of respondents (52.01%) reported receiving influenza vaccination at some point in the past, with 32.12% receiving it in the 2022–2023 flu season and 41.09% in the 2021–2022 season. The majority of respondents declaring acceptance of the vaccine for the 2022-2023 season were in the high-risk group. Only 17.28% of respondents declared receiving both influenza and SARS-CoV-2 vaccines in the 2022-2023 season, with the vast majority being respondents from the "high-risk group" (p

Abstract:High-pressure water jet technology has received extensive attention and application due to its high efficiency and environmental protection characteristics. The high-pressure water jet nozzle is its core component, and the research on the high-pressure water jet nozzle is conducive to improving the jet performance and improving the jet efficiency. This paper introduces the characteristics of water jet and the working principle of pure water jet, abrasive water jet, pulsed water jet and cavitation water jet, reviews the theoretical analysis and experiment of the predecessor's nozzle, briefly explains the application of high-pressure water jet and looks forward to the development trend of this technology.

A two element Multiple Input Multiple Output UWB (Ultra-wide band) antenna is presented in this paper. The antenna is backed by the FR-4 substrate with a thickness of 1.6 mm and dielectric constant of 4.3 covering an area of 52.8 × 29 mm2. The proposed MIMO antenna consists of two single UWB antennas and a stub placed between the two antennas to reduce the mutual coupling. The proposed antenna achieves the voltage standing wave ratio (VSWR) of less than 2 and more than 86% radiation efficiency over the whole band of interest. Performance of the antenna is examined using both simulation and experiment. The design exhibits good performance characteristics in terms of bandwidth, gain, efficiency, return loss and VSWR. The proposed antenna is analyzed using the CST Microwave Studio software. The prototype model of the antenna is fabricated, tested, and measured to validate the simulation return loss results. There is acceptable agreement between the measured and simulated results.

Although cancer care is often contextualized in terms of survival, there are other important cancer care outcomes, such as quality of life and cost of care. The ASCO Value Framework assesses the value of cancer therapies not only in terms of survival but with consideration of quality of life and financial cost. Early palliative care for patients with advanced cancer is associated with improved quality of life, mood, symptoms, overall survival, and cost savings. While palliative care has been shown to have numerous benefits, the impact of real-world implementation of outpatient embedded palliative care on value-based metrics is not fully understood. We sought to describe the association of outpatient embedded palliative care in a multidisciplinary thoracic oncology clinic on inpatient value-based metrics. We performed a retrospective cohort study of 215 patients being treated for advanced thoracic malignancies with non-curative intent. We evaluated the association of outpatient embedded palliative care with inpatient clinical outcomes including emergency room visits, hospitalizations, intensive care unit admissions, hospital charges, as well as hospital quality metrics including 30-day readmissions, admissions within 30 days of death, inpatient mortality, and inpatient hospital charges. Outpatient embedded palliative care was associated with lower hospital charges per day ($3,807 versus $4,695, p=0.024). Furthermore, patients who received outpatient embedded palliative care had decreased hospital admissions within 30 days of death (O.R. 0.50; 95% CI 0.34, 0.74; P<0.001) and decreased inpatient mortality (O.R. 0.46; 95%CI 0.23, 0.94; p=0.032). Our study further supports that outpatient palliative care is a high-value intervention and alternative models of palliative care, including one embedded into a multidisciplinary thoracic oncology clinic, is associated with improved value-based metrics.

Under the influence of various factors, the bronze ware unearthed by archaeology has various diseases of different degrees, and the mineralization problem is more prominent. The physical properties of mineralized bronzes have been destroyed, and the whole is loose and fragile, which is in urgent need of reinforcement and protection. Common reinforcement and protection materials mainly consider surface sealing, matrix bonding reinforcement and penetration reinforcement. Considering the low matrix strength and complex disease types of fragile bronzeware, it is difficult to achieve targeted protection with commonly used reinforcement and protection materials. In view of the problems such as poor permeability and easy discoloration of commonly used protection materials, this paper uses self-developed reinforcement and protection material AMC to compare its reinforcement and protection performance with B72, which has a high comprehensive evaluation on the performance of commonly used reinforcement and protection materials. The matrix strength was increased, and the appearance intervention degree was less than B72.

In this paper, a dual-band WiFi antenna and its Multiple Input Multiple Output (MIMO) system application is designed, fabricated, and measured based on the Chinese characters “Men” and “Wei”. The antenna uses a 40×40×1.6 mm3 Fr4 substrate to analyze the combinatorial structure of Chinese characters using the theory of characteristic modes (TCM), to optimize the antenna dimensions by analyzing the mode current distribution, and to broaden the antenna bandwidth by etching rectangular slots on the ground. The measured and simulated results show that the four-element MIMO antenna covers 5.68-8.01 GHz, the isolation between the antennas is higher than 20 dB in the working band, the Envelope Correlation Coefficient (ECC) and the channel capacity losses (CCLs)of the simulation is lower than 0.001 and 0.18 bits/s/HZ, respectively. The efficiency of the antenna is higher than 90%, and it can be used for WiFi communication band (5.8 GHz and 6 GHz).

Two-dimensional (2D) materials have been a research hot topic in the passed decades due to their unique and fascinating properties. Among them, mechanical properties plays an important role for their application. However, there lacks an effective tool for high-throughput calculating, analysing and visualizing the mechanical properties of 2D materials. In this work, we present, mech2d package, a highly automated toolkit for calculating and analysing second-order elastic constants (SOECs) tensor and relevant properties of 2D materials with considering their symmetry. In the mech2d, the SOECs can be fitted by both strain-energy and stress-strain approach, where the energy or strain can be calculated by first-principles engine, such as VASP. As a key feature, the mech2d package can automatically submit and collect the tasks from local or remote machine with robust fault-tolerant ability, make it suitable for high-throughput calculation. The present code has been validated by several common 2D materials, including graphene, black phosphorene, GeSe2 and so on.

Conventional phenotyping breeding approaches for vegetable crops like Solanaceae, Bulb, Root crops, have made a significant contribution by developing many varieties. Despite this, conventional phenotyping approaches are not sufficient due to the longer time taken to develop a variety, low genetic gain, environmental factors and some other externalities that affect the phenotype-based selection. To address the challenges of conventional phenotype, a new recent method of high throughput phenotyping (HTP) is considered a promising tool. The development of high-throughput phenotyping technology began in the preceding decade as advancements in sensor, computer vision, automation, and advanced machine learning technologies. HTP platforms are being utilized to undertake non-destructive assessments of the complete plant system in a range of crops. HTP provides the precise measurements and suggests the collection of high-quality and accurate data which is necessary for standardizing phenotyping for the collection of genetic dissection and genomic assisted breeding such as genome-wide association studies (GWAS), linkage mapping, marker-assisted selection (MAS), genomic selection (GS). The remainder of this chapter discusses how high-throughput phenotyping technologies can be used in genomic-assisted breeding for vegetable crops

In the process of deflagration of energetic materials, strong electromagnetic radiation is to be generated, which causes the surrounding electronic equipment to fail to work normally. To solve this problem, it is necessary to clarify the mechanism of electromagnetic radiation generated by energetic materials. The mechanism of plasma changed by the deflagration of energetic materials is an important topic in the aerospace and geophysics fields. The academic community holds two main viewpoints on the mechanism of electromagnetic radiation generated by energetic materials: one is that the solid material is squeezed and deformed during the deflagration of energetic materials, and the charges of different polarities rub in space to form effective electric dipoles, which eventually generate electromagnetic radiation. Another view is that the deflagration of energetic materials causes the temperature of the medium to rise sharply, and bremsstrahlung is formed during the compression and diffusion of the high-temperature wave front, resulting in the generation of electromagnetic radiation. This paper, based on theoretical analysis and experimental data, holds the view that electromagnetic radiation is generated by the high-temperature thermal effect. It studies the relationship between temperature and electromagnetic radiation and obtains quantitative analysis conclusions.

A supernova close enough to the Earth is a spectacular event: it can appear as a \new star" as luminous as Venus, or even more, visible for several days. The rate of Galactic supernovae is expected to be of about one in 30 years, with a fraction visible at naked eye; however in all the history of human civilization only seven supernovae in the Milky Way have been reported, the last two (1572 and 1604) during Galilei's life. The supernova of 1604, today called Kepler's Supernova, was observed by Galilei, Kepler and other astronomers in Europe, Korea, and China. Like the supernova SN1572, today called Tycho's supernova, it has been the subject of extensive studies, and inspired observational measurements and philosophical considerations on the nature of the heavens. The remnant of SN1604 has been indicated by recent X- and gamma-ray data to be a likely site of cosmic ray acceleration. The first recorded data of optical observations, together with new data, can still tell us a lot about the early evolution of this supernova.

Major progress in the field of regenerative medicine are expected from the design of artificial scaffolds that mimic both the structural and functional properties of the ECM. The bionanocomposites approach is particularly well fitted to meet this challenge as it can combine ECM-based matrices and colloidal carriers of biological cues that regulate cell behavior. Here we have prepared bionanocomposites under high magnetic field from Tilapia fish scale collagen and multifunctional silica nanoparticles (SiNPs). We show that scaffolding cues (collagen), multiple display of signaling peptides (SiNPs) and control over the global structuration (magnetic field) can be combined into a unique bionanocomposite for the engineering of biomaterials with improved cell performances.

Patch antennas are compact, less complex, planar structures and therefore, widely used in small satellite missions for telecommand, data link, and intersatellite link, particularly in S- band and X- band. Improved performance of these patch antennas in terms of gain and compactness will di-rectly affect the communication efficiency of small satellite missions. Especially the coming IoT (Internet of Things) constellations require high gain and efficient antenna arrays. An optimization of single patch antenna elements is an important cornerstone for the missions. Therefore, the ef-fects of various antenna enhancement techniques, such as slotted ground plane, resistor and ca-pacitor integration, parasitic patch elements, are analyzed. These techniques were applied on a rectangular patch antenna with parameter variation to identify the optimal performances with respect to bandwidth, operating frequency, gain, polarization, and power flow. Finally, the techniques were combined to obtain an optimized antenna in terms of gain and compactness. The results were compared to a slotted reference antenna. For the scenario of a 2.4 GHz patch antenna, a gain optimization of 27 % (from 7.09 to 8.14 dBi) or size reduction of 52 % (from 96.04 to 46.2 cm²) could be achieved. Overall, our study revealed an effective way to increase the patch antenna performance, which can directly contribute to more efficient communication links and design of antenna arrays.

Hepato-renal dysfunctions associated with hyperlipidemia necessitates continuous search for natural remedies. This study thus, evaluated the effect of dietary chitosan on diet-induced hyperlipidemic rats. Thirty male Wistar rats (90 ± 5.2) g were randomly allotted into six (6) groups (n=5): Normal diet, High-fat diet (HFD), Normal diet + 5% chitosan. The three other groups received HFD, supplemented with 1%-, 3%-, and 5% of chitosan. The feeding lasted for 8 weeks, after which the rats were sacrificed. The liver and kidneys were harvested for Analyses. Hepatic alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP) activity, and renal biomarkers (ALT, AST, urea, and creatinine) were assayed spectrophotometrically. Additionally, expression of hepatic and renal CD43 and p53 was estimated immunohistochemically. Hyperlipidemia caused a significant (p<0.05) decrease in the hepatic (AST, ALT, and ALP) and renal (AST and ALT) activities, while renal urea and creatinine increased. Furthermore, the HFD group showed an elevated level of hepatic and renal CD43 while p53 expression decreased. However, groups supplemented with chitosan showed improved hepatic and renal biomarkers, as well as corrected the aberrations in the expressions of p53 and CD43. Conclusively, dietary chitosan could effectively improve kidney and liver functionality via abatement of inflammatory responses.

We report world record high data transmission over standard optical fiber from a single optical source. We achieve a line rate of 44.2 Terabits per second (Tb/s) employing only the C-band at 1550nm, resulting in a spectral efficiency of 10.4 bits/s/Hz. We use a new and powerful class of micro-comb called soliton crystals that exhibit robust operation and stable generation as well as a high intrinsic efficiency that, together with an extremely low spacing of 48.9 GHz enables a very high coherent data modulation format of 64 QAM. We achieve error free transmission across 75 km of standard optical fiber in the lab and over a field trial with a metropolitan optical fiber network. This work demonstrates the ability of optical micro-combs to exceed other approaches in performance for the most demanding practical optical communications applications.

Microcombs provide a potential compact and efficient light source for multi-Terabit-per-second optical superchannels. However, as the bandwidth of these multi-wavelength light sources is increased, this can result in low per-line power. Optical amplifiers can be used to overcome power limitations, but the accompanying spontaneous optical noise can degrade performance in optical systems. To overcome this issue, we propose wideband noise reduction for comb lines using a high-Q microring resonator, whose resonances align with comb lines. When applying the proposed distillation to a superchannel system with 18 Gbaud, 64-QAM sub-channels in a > 10 Tb/s optical superchannel, we find that noise-corrupted comb lines can reduce the optical signal-to-noise ratio required for the comb by ~ 9 dB when used as optical carriers at the transmitter side, and by ~ 12 dB when used as a local oscillator at the receiver side.

ATLID (ATmospheric LIDar) is the atmospheric backscatter LIDAR (Light Detection and Ranging) on board of the EarthCARE (Earth Cloud, Aerosol and Radiation Explorer) mission, the sixth Earth Explorer Mission of the ESA (European Space Agency) Living Planet Programme [1-5]. ATLID’s purpose is to provide vertical profiles of optically thin cloud and aerosol layers, as well as the altitude of cloud boundaries [6-10]. In order to achieve this objective ATLID emits short duration laser pulses in the UV, at a repetition rate of 51 Hz, while pointing in a near nadir direction along track of the satellite trajectory. The atmospheric backscatter signal is then collected by its 620 mm aperture telescope, filtered through the optics of the instrument focal plane assembly, in order to separate and measure the atmospheric Mie and Rayleigh scattering signals. With the completion of the full instrument assembly in 2019, ATLID has been subjected to an ambient performance test campaign, followed by a successful environmental qualification test campaign, including performance calibration and characterization in thermal vacuum conditions. In this paper the design and operational principle of ATLID is recalled and the major performance test results are presented, addressing the main key receiver and emitter characteristics. Finally, the estimated instrument, in-orbit, flight predictions are presented; these indicate compliance of the ALTID instrument performance against its specification and that it will meet its mission science objectives for the EarthCARE mission, to be launched in 2023.

The rapidly increasing adoption of high-resolution accurate-mass methods in analytical laboratories has fueled demand for instruments that combine high performance and reliability with small size and greater ease-of-use. This paper presents the major design principles that are driving the evolution of the hybrid quadrupole-Orbitrap instrument architecture to enable a greater range of applications and users. These principles may be summarized as follows: better usage of physical space and better access for service by means of size reduction of pumping and ion optics; expanded use of technologies from electronics in ion-optical design; flexibility in performance via modularity of design of the hardware and software components; and, harmonization of interfaces with other instruments to facilitate sharing and transferability of analytical workflows. The design of a novel family of hybrid mass spectrometers is described in detail, and performance evaluation is carried out on a wide variety of samples for its three representatives: the Orbitrap Exploris 120, Orbitrap Exploris 240 and Orbitrap Exploris 480 mass spectrometers.The new instrument family is shown to offer compelling potential not only for high-end proteomics and biopharmaceutical applications, but also for screening, trace, targeted and clinical analysis by liquid chromatography/mass spectrometry methods.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

Topology optimization is a pioneering design method that can provide various candidates with high mechanical properties. However, the high-resolution for the optimum structures is highly desired, normally in turn leading to computationally intractable puzzle, especially for the famous Solid Isotropic Material with Penalization (SIMP) method. In this paper, an efficient and high-resolution topology optimization method is proposed based on the Super-Resolution Convolutional Neural Network (SRCNN) technique in the framework of SIMP. The SRCNN includes four processes, i.e. refining, path extraction & representation, non-linear mapping, and reconstruction. The high computational efficiency is achieved by a pooling strategy, which can balance the number of finite element analysis (FEA) and the output mesh in optimization process. To further reduce the high computational cost of 3D topology optimization problems, a combined treatment method using 2D SRCNN is built as another speeding-up strategy. A number of typical examples justify that the high-resolution topology optimization method adopting SRCNN has excellent applicability and high efficiency for 2D and 3D problems with arbitrary boundary conditions, any design domain shape, and varied load.

Methods of path integrals are used to develop multi-factor probabilities of bid-ask variables for use in high-frequency trading (HFT). Adaptive Simulated Annealing (ASA) is used to fit the nonlinear forms so developed to a day of BitMEX tick data. Maxima algebraic code is used to develop the path integral codes into C codes, and sampling code is used for the fitting process. After these fits, the resultant C code is very fast and useful for forecasting upcoming ask, bid, midprice, etc., when narrow and wide windows of incoming data are used. A bonus is the availability of canonical momenta indicators (CMI) useful to forecast direction and strengths of these variables.

Three hundred ten 12-wek-old laying quails (155 each) were randomly selected from the initial population and kept in individual battery cages. The measurements of growth and egg production were determined to derive RFI. The relationship between RFI and egg quality, blood parameters and carcass characteristics was also determined. The results indicated that the gray quails had significantly higher egg mass and lower broken eggs compared to the white quails. A significant increase for eggshell strength and shell % was found in eggs produced from gray quails compared to white counterparts, although the shell thickness was the same. The results of multiple regression analysis clearly identified a significant effect of metabolic body weight and egg mass in computing expected feed intake rather than body weight gain in both varieties of Japanese quails. Strongly positive correlation between RFI and feed intake in both gray and white quail varieties was found. The same trend was also observed for feed conversion ratio (FCR). Therefore, including RFI in selection criteria of Japanese quail to improve FCR under high environmental temperature is highly recommended.

With the continual global increase of PV power systems and the inherent weather-induced volatility of their power output, understanding the underlying variability of solar radiation in both space and time is important for the planning and reliable operation of future power grids. This paper concisely reviews recent advances in the characterization of irradiance variability with an emphasis on small spatial and temporal scales (respectively less than about 10\,km and 1\,min), for which comprehensive data sets are time consuming and expensive to collect, and although needed have not been available until recently. Special attention is given to studies dealing with the quantification of variability using such unique data, the analysis and modeling of spatial smoothing, and the evaluation of temporal averaging.

Evaluation of the effect of a high frequency acceleration device on clear aligner exchange intervals and treatment time required to achieve prescribed tooth movements. Sixteen subjects with similar Class I malocclusions, 5mm or less crowding, and treated with Invisalign were divided into two groups. Group 1 (experimental; N=8) underwent aligner treatment in conjunction with daily use of the high frequency acceleration device and exchanged aligners every 5 days. Group 2 (controls; N=8) underwent aligner treatment without use of the device and exchanged aligners every 14 days according to the manufacturer's recommended interval. All subjects were treated by one investigator, and results were evaluated by both; total number of aligners used, and number of refinements required, prior to final Vivera retention scan. A significant decrease in both treatment time, and number of aligners required to complete treatment was observed by experimental subjects as compared to controls. In addition, no refinements were required by experimental subjects, whereas 6 of 8 of the control subjects required 1 or more refinements. Use of the high frequency acceleration device in conjunction with Invisalign treatment resulted in more predictable tooth movement and a significant decrease in the length of treatment.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

In this study, we investigate the influence of control type and strain rate on the lifetime of specimens manufactured from 50CrMo4. This influence is described by a strain rate dependent method that uses cyclic stress strain curves to correct displacement controlled cyclic test results. The objective of this correction is to eliminate the stress related differences between displacement controlled cyclic test results and force controlled cyclic test results. The method is applied to the results of ultrasonic fatigue tests of six different combinations of heat treatment, specimen geometry (notch factor) and atmosphere. The corrected results show an improved agreement with test results obtained on conventional fatigue testing equipment with similar specimens: the standard deviation in combined data sets is significantly reduced (p=4.1%). We discuss the literature on intrinsic and extrinsic strain rate effects in carbon steels.

Abiotic stress in plants is an increasingly common problem in agriculture, and thus, studies on plant treatments with specific certain compounds that may help to mitigate these effects have increased in recent years Melatonin (MET) application and its role in mitigating the negative effects of abiotic stress in plants have become important in the last few years. MET, a derivative of tryptophan, is an important plant-related response molecule involved in the growth, development, and reproduction of plants, and the induction of different stress factors. In addition, MET plays a protective role against different abiotic stresses such as salinity, high/low temperature, high light, waterlogging, nutrient deficiency and stress combination by regulating both the enzymatic and non-enzymatic antioxidant defense systems. Also, MET interacts with many signaling molecules, among these, reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. It is well known that NO produces S-nitrosylation and NO2-Tyr of important antioxidant-related proteins, being this an important mechanism for maintaining the antioxidant capacity of the AsA/GSH cycle under nitro-oxidative conditions, being extensively reviewed here under different abiotic stress conditions. Lastly, in this review, we show the coordination between NO and MET as a long-range signaling molecule, regulating many responses in plants, including plant growth and abiotic stress tolerance. Despite all the knowledge acquired over the years, there is still more to know about how MET and NO act on tolerance to abiotic stresses.

To address the issue of traditional static evaluation models being unable to comprehensively analyse the performance of ultra-supercritical coal-fired units under varying loads, we propose a dynamic comprehensive evaluation model based on the improved Criteria Importance Through Inter-criteria Correlation (CRITIC) method and Entropy Weight Method (EWM). The comprehensive performance evaluation index system of ultra-supercritical coal fired units is constructed by examining the boiler performance, turbine performance, plant power performance, environmental performance, and flexible performance of coal powered units. The CRITIC and EWM methods are used to calculate the weights of the indicators, which are then combined with the static evaluation results. Using a dynamic comprehensive evaluation model, we analysed ultra-supercritical coal-fired units, taking into account time weight. This allowed us to obtain the comprehensive dynamic real-time evaluation value of the units under different loads. The research indicates that the dynamic comprehensive evaluation model, which uses an improved CRITIC and EWM, has significant advantages in improving evaluation accuracy, weight-balanced distribution, and generality. Provides more accurate, reasonable, and reliable evaluation results for practical decision making.

Pachychoroid neovasculopathy (PNV) is a pachychoroid-spectrum disease. As blood circulation throughout the choroid may be involved in PNV pathogenesis, analysis using ultra-wide-field (UWF) fundus imaging is crucial. We evaluated choroidal thickness after half-fluence photodynamic therapy (PDT) combined with intravitreal aflibercept injection for PNV using UWF swept-source optical coherence tomography. Seventeen eyes with PNV that underwent half-fluence PDT with adjuvant single intravitreal aflibercept injection were analyzed. To compare choroidal thicknesses in the central and peripheral choroids, we set subfields <3, <9, and 9–18 mm from the fovea. The <9- and 9–18-mm subfields were divided into four quadrants. Choroidal thickness in each subfield decreased significantly after half-fluence PDT (P<0.001); this reduction was more pronounced in the central area. We also investigated the relationship between the dominant side of the deep choroidal veins that harbor choroidal vein efflux from the macula. When choroidal thickness in the supratemporal and infratemporal 9x9-mm subfields were evaluated, the ratio of choroidal thickness reduction was not significantly different between the dominant and non-dominant sides. The dominant side was not associated with the extent of choroidal thickness reduction in PNV. In conclusion, half-fluence PDT caused thinning of the entire choroid, especially in the central area, in PNV.

This research paper investigates ultra-wideband (UWB) localization systems by focusing on the use of average filter (AVG), Kalman filter (KF), and extended Kalman filter (EKF) algorithms, as well as a novel integrated filtering method that incorporates low-pass filter (LPF) into AVG, KF, and EKF. The study aims to improve localization loss in indoor environments using a TurtleBot robot equipped with a camera to observe ground truth positions. To evaluate the effectiveness of the proposed algorithms, a comprehensive comparison of the raw and filtered data with the camera-based ground truth observations is performed. Quantitative analyses of the results, including max, min, max-min, and mean error, are performed to evaluate the localization performance of the algorithms and the integrated filtering method. The results reveal that the integrated filtering method has performed better accuracy in comparison with existing methods.

Age-related macular degeneration (AMD) causes visual impairment in individuals >50 years of age. However, no study has investigated AMD using ultra-wide-field swept-source optical co-herence tomography (UWF SS-OCT). We aimed to evaluate central and peripheral choroidal thickness using UWF SS-OCT and compare AMD subtypes. We included 75 eyes of patients with typical AMD (tAMD), 56 with polypoidal choroidal vasculopathy (PCV), 29 with pachychoroid neovasculopathy (PNV), and 12 with retinal angiomatous proliferation (RAP). To compare cho-roidal thicknesses in the central and peripheral choroids, we established subfields of <3 mm, <9 mm, and 9–18 mm from the fovea. PNV patients were significantly younger than those with tAMD (P=0.01). The choroidal thicknesses of PNV were significantly greater than that of tAMD in all subfields (P<0.01) and choroidal thickness significantly correlated with age and axial length in all subfields (P<0.05). Even after adjusting for age and axial length, the choroidal thickness in PNV was significantly greater than that in tAMD (P<0.05). In addition, the ratio of the posterior < 9 mm to peripheral 9–18 mm choroidal thickness in PNV was significantly greater than that in tAMD (P<0.01). A thickened choroid in PNV was more pronounced in the posterior choroid than in the periphery.

In light of the current situation where no testing equipment is available for measuring thermal deformation of objects, this paper proposes a novel method for accurate and precise measurement. The method overcomes the limitations of previous approaches that relied on pitch angle. By utilizing the principle of biplane multiple reflections, a bivariate laser spot displacement analysis algorithm is devised to attain highly precise measurements of bivariate angles. Additionally, a temperature gradient comparison algorithm is introduced to calculate the indicator test results under specific temperature conditions. To validate the effectiveness and reliability of this method, a testing system is constructed and utilized. The results demonstrate that the thermal deformation angle change test achieves an impressive accuracy of 0.015″ and a rate of thermal deformation angle change of 0.3247″/°C. These values are in close agreement with the previously simulated analysis result of 0.359″/°C, with only a relative error of 9.55%. Therefore, the test results confirm the efficacy and reliability of this testing method along with the feasibility of the algorithm processing.

We put forward a co-axial pump(optical)-probe(X-rays) experimental concept and show performance of the optical component. A Bessel beam generator with a central 100 micrometers-diameter hole (on the optical axis) was fabricated using femtosecond (fs) laser structuring inside a silica plate. This flat-axicon optical element produces a needle-like axial intensity distribution which can be used for the optical pump pulse. The fs-X-ray free electron laser (X-FEL) beam of sub-1 micrometer diameter can be introduced through the central hole along the optical axis onto a target as a probe. Different realisations of optical pump are discussed. Such optical elements facilitate alignment of ultra-short fs-pulses in space and time and can be used in light-matter interaction experiments at extreme energy densities on the surface and in the volume of targets. Full advantage of ultra-short 10 fs X-FEL probe pulses with fs-pump(optical) opens an unexplored temporal dimension of phase transitions and the fastest laser-induced rates of material heating and quenching. A wider field of applications of fs-laser-enabled structuring of materials and design of specific optical elements for astrophotonics is presented.

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

Abstract: Power generation using dielectric elastomer (DE) artificial muscle is attracting attention because of its light weight, low cost, and high efficiency. Since this method is a system that produces electricity without emitting carbon dioxide nor using rare earths, it would contribute to the goal of environmental sustainability. In this paper, the background of DEs, the associated high-efficient wave energy generation (WEG) systems that we developed using DEs, as well as the latest development of its material are summarized. By covering the challenges we face and the achievements that we’ve reached, we can discuss the opportunities to build the foundation of a recycled energy society through the usage of these WEGs. On the other hand, to make these possibilities commercially successful, the advantages of DEs need to be integrated with traditional technologies. To achieve this, we also consider the method of using DEs alone and a system used in combination with an oscillating water column. Finally, the current status and future of DEGs are discussed.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.