A single-crystal of ytterbium-doped “mixed” yttrium-lutetium aluminium garnet with a stoichiometric composition of (Y0.601Lu0.233Yb0.166)3Al5O12 was grown by the Czochralski method and its structure, vibronic, spectroscopic and laser properties were studied. The stimulated-emission cross-section for Yb3+ ions was maximized to 2.53×10-20 cm2 at 1031 nm, the emission bandwidth is ~8 nm and the reabsorption-free luminescence lifetime of the 2F5/2 state is 1.063 ms. Pumped at 941 nm, the Yb-laser generated a maximum output power of 1.04 W at 1.03 and 1.05 μm with a high slope efficiency of 76.4% and a laser threshold of 76 mW. A continuous wavelength tuning over a range of 51.6 nm (1026.4 - 1078.0 nm) was also achieved. Power scaling is achieved using a 969 nm-diode pumped microchip cavity. A maximum output power of ~9 W is obtained at 1.05 μm with a slope efficiency of 76% and with an almost circular laser beam profile.

Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A three-dimensional, time-dependent, computational fluid dynamics model of a single channel of a F10 SOFC stack in Forschungszentrum Jülich GmbH is developed to investigate chromium poisoning for different stack designs, temperatures and absolute air humidities. The model takes into account both chemical and electrochemical mechanisms of chromium poisoning and is able to predict the spatial distribution of SrCrO4 and Cr2O3. The voltage degradation over 100 kh can be simulated quantitatively. According to the simulation results, chromium poisoning is almost eliminated by the application of the protective coating fabricated by the atmospheric plasma-spraying (APS) technology. Besides, with the help of the APS protective coating, operating a SOFC stack with less dehumidified air at 650 oC is possible according to the simulation.

Oxide additive-free α- ⇀ β-Si3N4 phase transformation of a high-purity commercial α-Si3N4 powder was investigated at 1600 to 1900 ℃ under nitrogen pressure of 980 kPa. The XRD analysis revealed that the α- ⇀ β-Si3N4 phase transformation proceeded mainly at 1900 ℃, and was completed by the extensive 1900 ℃-heat treatment for 20 h. This phase transformation temperature was 33 ℃ lower than the theoretical α-Si3N4 dissociation temperature and confirmed as completely different from that often discussed for the liquid phase sintering of α-Si3N4 powder by direct comparison with the phase transformation behavior of a reference powder, α-Si3N4 powder doped with 1 mol% Y2O3. The unique α- ⇀ β-Si3N4 phase transformation was further studied by a set of characterization techniques including elemental analysis, HAADF-STEM and STEM-EDS analyses. The results strongly suggested that the oxide additive-free α- ⇀ β-Si3N4 phase transformation was governed by the for-mation of metastable solid solution between α-Si3N4 and impurity oxygen of approximately 0.6 wt%, which promoted the dissociation below the theoretical α-Si3N4 dissociation temperature to afford thermodynamically favorable β-Si3N4. Along with the β-Si3N4 formation, the impurity oxygen was concentrated at the Si3N4 crystal grain boundaries and subsequently released from the sample via the grain boundary diffusion.

The management and classification of solid waste is one of the most important challenges around the world, in order to sustain economic growth and preserve the environment. The objective is to propose the use of Smart Ecological Points as a strategy to address the problem related to the solid waste management system at the source, which has become one of the biggest problems globally and Colombia is no exception. The article describes the current state of the problem in the country and in turn, presents the possibility of developing a prototype corresponding to a low-cost Smart Ecological Point supported by the use of an experimental capacitive sensor and Machine Learning algorithms, which will reduce the time necessary for the classification of recyclable and non recyclable waste, minimizing the health risks and increasing the percentage of waste that can be reused, by reducing the probability of being contaminated at the source, an aspect that is very common when done manually. According to the results obtained, it was evident that the proposed prototype made an adequate classification of waste, generating the possibility of being manufactured with existing technology in the environment, in order to promote adequate waste classification at the source.

In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.

The buildup dynamics of diode-pumped passively mode-locked solid-state laser is thoroughly explored by the real-time measurement with temporal sampling rate up to 40 GHz. A concise cavity is developed to ensure the transient dynamics purely arising from the gain medium and saturable absorber. Experimental results reveal that the laser output in the buildup process exhibits numerous passively Q-switched pulses followed with a damped relaxation oscillation prior to the stable mode locking. Furthermore, it is confirmed that the laser output has already displayed single clean mode-locked pulses inside the first several Q-switched envelopes before stepping into the stage of relaxation oscillation. The present real-time exploration is expected to provide important information for practical applications with temporal modulation of the pump intensity.

Keywords: Kenaf; liquid cultivation; solid cultivation; in vitro propagation, life on land

NaClO3 and NaBrO3 are believed to form a complete solid solution from RT to fusion. The unique solid phase can thus be written: NaClO3 (1-x)-NaBrO3 (x) with: 0 ≤ x ≤ 1. This study shows that at high temperature this statement might be valid. Nevertheless, up to 50°C and probably up to 160°C and even higher temperature, this is not true when the system is in thermodynamic equilibrium. A large miscibility gap exists at room temperature (RT). This gap could be reduced up to a complete disappearance by fast crystallization, for instance by spray-drying. The necessary conditions to access to equilibrium including homochirality are also discussed.

The present work describes the synthesis, characterization and photomineralization activity of synthesized Ce1-xZnxO2-x solid solution catalysts allowing the degradation of Diclofenac as a model of anti-inflammatory medicines in water. Oxygen deficient photocatalysts Ce1-xZnxO2-x (CeZnx), produced with mixing ZnO and CeO2 have been characterized for their crystallographic parameters, specific surface area and morphology. Photomineralization activity determinations using TOC analysis have shown efficient diclofenac photooxidation under sunlight. Moreover, results indicate that coexistence of Zn2+, Ce4+ and oxygen vacancies rate in CeZnx solid solution are key factors for strong drug mineralization. Finally, CeZn0.1 which is one of the photocatalysts synthesized in the present work represents a cheap and efficient reagent for organic matter photomineralization in wastewater.

The battle of currents between AC and DC reignited as a result of the development in the field of power electronics. The efficiency of DC distribution systems is highly dependent on the efficiency of distribution converter, which calls for optimized schemes for efficiency enhancement of distribution converters. Modular solid-state transformers play a vital role in DC Distribution Networks and Renewable Energy systems (RES).This paper deals with efficiency-based load distribution for Solid State Transformers (SSTs) in DC distribution networks. Aim is to achieve a set of minimum inputs that are consistent with output while considering constraints and efficiency. As the main feature of modularity is associated with a three-stage structure of SSTs. This modular structure has been optimized using Ant Lion Optimizer (ALO) and validated by applying it EIA (Energy Information Agency) DC Distribution Network which contains SSTs. In the DC distribution grid, modular SSTs provide promising conversion of DC power from medium voltage to lower DC range (400V). The proposed algorithm is simulated in MATLAB and also compared with two other metaheuristic algorithms. The obtained results prove that the proposed method can significantly reduce input requirements for producing the same output while satisfying the specified constraints.

Agriculture has been experiencing a difficult situation because of limiting factors in its production, Natural biostimulants (NBs) have emerged as a novel alternative. This study reviews NBs produced through Solid-State Fermentation (SSF) from organic waste, focusing on the processes and production methods. The aim is to highlight their potential for improving agricultural productivity and promoting sustainable agriculture. Through a literature review, the effects of NBS on crops were examined, as well as the challenges associated with their production and application. The importance of standardizing production processes, optimizing fermentation conditions, and assessing their effects on different crops is emphasized. Furthermore, future research areas are identified, such as enhancing production efficiency and evaluating the effectiveness of SSF-produced NBS in different agricultural systems. In conclusion, SSF-produced NBS offers a promising alternative for sustainable agriculture, but further research and development are needed to maximize its efficacy and enable large-scale implementation.

The isolation and potential applications of chitosan from the fungal source is an alternative to crustacean chitosan and synthetic polymers. The strains of Basidiomycota (Heterobasidion annosum, Phanerochaete chrysosporium, Pleurotus ostreatus, Trametes versicolor, Lentinus lepideus) with different environmental distribution, ecological importance, and industrial application were studied for mycelial biomass production in submerged (SF) and solid state fermentation (SSF). Further, the chitosan from fungal cells was extracted and characterized by elemental analyses (nitrogen) and FTIR spectroscopy. The fruiting bodies of Pleurotus ostreatus, Agaricus bisporus and Ganoderma ap-planatum were chosen as a reference material of chitosan content in basidiocarps. Stationary SF gave the lowest biomass yield in comparison with shaken SF and SSF. The role of aeration and agitation in biomass production was clearly observed in shaken SF with the highest yield achieved by P. chrysosporium. The highest biomass yield in SSF produced P. ostreatus and T. versi-color. The content of chitosan within fungal species varied depending on the method of cultiva-tion. The highest chitosan yield among the cultivated strains was obtained from mycelium of P. chrysosporium and T. versicolor in SF. The highest chitosan yield in fungal fruiting bodies demon-strated commercially cultivated mushroom A. bisporus. The extracted chitosan is proposed as functional biopolymer additive for ecological materials to substitute the synthetic wet and dry strength agents in packaging materials.

Environmental degradation is one of the most visible problems in Hargeisa. Currently, solid waste is disposed of at two dumping sites within the city limits causing nuisance and unsanitary conditions. Moreover, the existing dumpsites are on the verge of closure, therefore necessitating a dire need to be addressed. This research paper is aimed to integrate multicriteria decision analysis and GIS for evaluating the site suitability for the landfill in Hargeisa, Somaliland. For this purpose, eleven significant parameters were selected: proximity from built-up areas, surface water, groundwater well points, sensitive sites (Airports), land use/land cover, geology, soil type, elevation, slopes, roads, and distance to existing dumpsites. These were then integrated using an analytical hierarchy process (AHP). Subsequently, restriction buffer analysis was performed on the seven parameters to obtain better and more accurate results, and restricted zones were omitted. Furthermore, the pair-wise comparison used to obtain priorities between the selected criteria showed that the land uses land cover is the most significant criterion in the model with a relative weight of 0.1829, followed by the habitations, 0.1506. The overall result reveals that about 68.96% (21060.9 ha) of the study area is unsuitable, while 24.36% (7441.53 ha) and 6.68% accounted for the less and highly appropriate zone, respectively. Following the results of this study, Hargeisa City's municipal council must reconsider the waste management and landfill sites to solve the problems observed in the area before it is overdue. Furthermore, this systematic research approach will assist regional and global researchers, policymakers, and municipal governments.

In this paper, in order to provide proper parameters for the preparation of semi-solid billets, the semi-solid annealing of hot-rolled 2A14 Al alloy was investigated. The microstructure was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) with X-ray energy dispersive spectrometer (EDS) and electron backscattered diffraction (EBSD), scanning transmission electron microscope (STEM). XRD results show that with the increase of temperature, equilibrium θ-Al2Cu gradually dissolved in the matrix. The EDS results of SEM and STEM show that there were coarse θ-Al2Cu phase, ultra-fine precipitate Al(MnFeSi) or (Mn, Fe)Al6 phase and atomic clusters in the microstructure. EBSD results show that the recrystallization mechanism was dominated by continuous static recrystallization (CSRX), the homogeneous nucleation occurred when the sample was heated to near solidus temperature, and CSRX happened in the semi-solid temperature. In the process of recrystallization, the micro-texture changed from preferred orientation to random orientation. A variety of experimental results show that static recrystallization (SRX) occurred at semi-solid temperature due to the blocking effect of atomic clusters on dislocation slip and the Zener drag effect of fine precipitates on low angle grain boundaries (LAGBs) disappeared with melting at semi-solid temperature.

The impact of nutrients on the environment, particularly on water bodies, has led to extensive studies for nutrient control. Within this context, studies have been focused on source separation of human urine from domestic wastewater to recover nutrients. Potassium is one of the most important components of human urine. However, data on potassium removal or recovery are quite limited except for some indirect information through use of zeolites for mostly ammonia removal. Potassium struvite or K-struvite (MgKPO₄·6H₂O) is a sparingly soluble salt belonging to struvite and has the potential of being used as a means of potassium and phosphate recovery from segregated human urine. This study aimed to assess the potential of K-struvite precipitation for control and recovery of nutrients. Within this context, K-struvite precipitation experiments were performed on both synthetically prepared samples and synthetic human urine solution to determine effect of operation parameters i.e. pH, stoichiometry, and temperature on potassium recovery performance. Results indicated that process performance as well as type of solid phases co-precipitated with K-struvite were closely related to initial potassium concentration, pH and reaction stoichiometry. At pH 10, the potassium recovery efficiency was maximized up to 87% by application of 100% excess dose of Mg and P for both synthetic samples and synthetic human urine solution. On the other hand, application of excess dose of K did not provide any improvement in K recovery efficiency. The effect of temperature on solubility of K-struvite was insignificant at the temperature of 24-90°C. Solid phase analyses confirmed that K-struvite was co-precipitated with either Mg₃(PO₄)₂, MgNaPO₄·7H₂O, or MgHPO₄·7H₂O depending on pH and stoichiometry instead of a pure compound.

Li3FeN2 material was synthesized by two-step solid-state method from Li3N (adiabatic camera) and FeN2 (tube furnace) powders. Phase investigation of Li3N, FeN2 and Li3FeN2 were carried out. Discharge capacity of Li3FeN2 is 343 mAh g-1, that is about 44.7% of theoretic capacity. The molar heat capacity of Li3FeN2 at constant pressure in the temperature range 298-900 K should be calculated as Cp,m = 77,831 + 0,130 × T – 6,289 × T-2, where T is absolute temperature, . Thermodynamic characteristics of Li3FeN2 were determined as next: entropy S0298 = 116.2 J mol-1 K-1, molar enthalpy of dissolution ΔdHLFN = ˗ 206,537 ± 2,8 kJ mol−1, the standard enthalpy of formation ΔfH0 = ˗ 291.331 ± 5.7 kJ mol−1, entropy S0298 = 113.2 J mol-1 K-1 (Neumann-Kopp rule) and 116.2 J mol-1 K-1 (W.Herz rule), the standard Gibbs free energy of formation ∆f G0298 = ˗276,7 kJ mol-1.

Solid-state lighting has been replacing conventional lighting in the market, raising concerns for implementing an efficient end-of-life management system. Since LED waste streams have not been quite dominant, characterization studies (product-level characteristics, component-wise information, bill of materials, diversity, and differences) are inconsistent and having substantial gaps. This study investigates the end-of-life LED lamp literature, focusing on the bill-of-materials, and reveals that the characterization procedure suffers from a severe lack of sample representativeness. Consequently, characterization results are widely varied and not generalizable. Moreover, most of the studies did not inform and document the detailed sample characteristics, precluding the possibility of identifying reasons for variation. Combining available information from the recent studies, we present a mass distribution at the component level, exemplifying the prospect for meeting EU regulatory limit and the need for more insight at the lamp and component level. To fill the disconnection between lamp level characteristics and component and material content, we propose a characterization protocol that carefully documents lamp, component, and material level information by establishing a lamp-component–material composition nexus. The protocol may help researchers, policymakers, and industrial stakeholders conduct a systematic characterization, analyze complexities and prepare for a sustainable solution.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

The coordination polymer [Fe(NH₂trz)₃](2ns)₂ exhibits the rare phenomenon of spin crossover in an attractive temperature range, i.e., somewhat above room temperature. Spin crossover in [Fe(NH₂trz)₃](2ns)₂ is manifest by thermochromism, which is accompanied by a magnetic transition from diamagnetism to paramagnetism. However, [Fe(NH₂trz)₃](2ns)₂ is brittle and difficult to process, which limits its use. In this study, we show that [Fe(NH₂trz)₃](2ns)₂ can be co-processed with ultrahigh molecular weight polyethylene (UHMWPE), which possesses outstanding mechanical properties, particularly when tensile drawn. Therefore, [Fe(NH₂trz)₃](2ns)₂–UHMWPE blends were gel-processed by extrusion, employing a relatively poor solvent, which has recently been shown to offer advantages compared to good solvents. Uniform and flexible films, ribbons and fibers with [Fe(NH₂trz)₃](2ns)₂ fractions as high as 33.3% m/m were obtained that could be readily drawn. Spin crossover in the coordination polymer is retained in these materials, as evident from their thermochromism. The tensile strength and Young’s modulus of the blends exceed those of typical commodity polymers. Thus, the films, ribbons and fibers constitute a special class of multifunctional materials that combine the flexibility and excellent mechanical properties of drawn UHMWPE with the spin crossover behavior of [Fe(NH₂trz)₃](2ns)₂.

Solid particles immersed in a fluid can be found in many engineering, environmental or medical fields. Applications are suspensions, sedimentation processes or procedural processes in the production of medication, food or construction materials. While homogenized behavior of these applications is well understood, contributions in the field of pore-scale fully resolved numerical simulations with non-spherical particles are rare. Using Smoothed Particle Hydrodynamics (SPH) as a simulation framework, we therefore present a modelling approach for Direct Numerical Simulations (DNS) of single-phase fluid containing non-spherically formed solid aggregates. Notable and discussed model specifications are the surface-coupled fluid-solid interaction forces as well as the contact forces between solid aggregates. The focus of this contribution is the numerical modelling approach and its implementation in SPH. Since SPH presents a fully resolved approach, the construction of arbitrary shaped particles is conveniently realizable. After validating our model for single non-spherical particles, we therefore investigate the motion of solid bodies in a Newtonian fluid and their interaction with the surrounding fluid by analyzing velocity fields of shear flow with respect to hydromechanical and contact forces. Results show a dependency of the motion and interaction of solid particles on their form and orientation. While spherical particles move to the centerline region, ellipsoidal particles move and rotate due to vortexes formation in the fluid flow in between.

The present work describes the optimization and validation of a highly selective and sensitive analytical method using solid phase extraction and liquid chromatography tandem mass spectrometry (SPE LC-MS/MS) for the determination of some frequently prescribed pharmaceuticals in urban wastewater received and treated by Sharjah sewage treatment plant (STP). The extraction efficiency of different SPE cartridges was tested and the simultaneous extraction of pharmaceuticals was successfully accomplished using hydrophilic-lipophilic-balanced reversed phase Waters^® Oasis HLB cartridge (200 mg/ 6 mL) at pH 3. The analytes were separated on an Aquity BEH C₁₈ column (1.7 µm, 2.1 mm x 150 mm) using gradient elution and the mass spectrometric analysis were performed in multiple reactions monitoring (MRM) selecting two precursor ions to produce ion transition for each pharmaceutical using positive electrospray ionization (+ESI) mode. The correlation coefficient values in the linear calibration plot for each target compound exceeded 0.99 and the recovery percentages of the investigated pharmaceuticals were more than 84%. Limit of detection (LOD) varied between 0.1-1.5 ng/L and limit of quantification (LOQ) was 0.3-5 ng/L for all analytes. The precision of the method was calculated as the relative standard deviation (RSD%) of replicate measurements and was found to be in the ranges of 2.2% to 7.7% and 2.2% to 8.6% for inter and intra-day analysis, respectively. All of the obtained validation parameters satisfied the requirements and guidelines of analytical method validation.

Suzuki cross-coupling reaction has developed one of the furthermost effectual approaches for the synthesis of biaryls or substituted aromatic moieties from aryl halides and arylboronic acids with a palladium-catalyst in the past two era’s. Herein, Pd-free layered double hydroxide containing nickel catalysts were prepared by co-precipitation method under ultrasonic irradiation and N2 atmosphere with different molar ratios of Ni: Mg: Al and coded as (1NiLDHs-Dr), (1.5NiLDHs-Dr) and (2NiLDHs-Dr). A series of reduced catalysts under 5%H2/N2 at different temperatures were coded as 1NiLDHs-R200, 1.5NiLDHs-R200 and 2NiLDHs-R200. As-synthesized 2NiLDHs-Dr was the superlative catalyst when coupling different aryl halides with different boronic acids derivatives. Deep investigation of all catalysts was done using different techniques such as inductively coupled plasma optical emission spectroscopy (ICP-OES), x-ray photoelectron spectroscopy (XPS), powder x-ray diffraction (XRD), thermogravimetric analyses (TGA), Fourier transfer infrared (FTIR), scanning electron microscope (SEM) connected with energy dispersive x-ray (EDX) and N2-physisorption at -196 ℃. The results attained verified that ɑ-Ni(OH)2 was fashioned for 2NiLDHs-Dr catalyst and the enclosure of nickel ions in the cationic sheet of layered structure were responsible for the fascinating catalytic efficacy rather than the basic nature of material. The Ni-containing LDHs catalysts encourage forthcoming studies in Pd-free catalyzed C-C coupling reactions.

Pharmaceuticals contain biologically active components that can pollute water courses as a result of the excretions from individuals and/or uncontrolled release of residues from chemical plants, and they can pose a hazard to health. Pharmaceutical residues can persist at low concentrations in the environment, and thus may be potentially harmful to aquatic animals and to humans. Controlling and monitoring such residues are therefore a prime interest, for example, a solid-phase extraction uses solid sorbents to purify and preconcentrate the residues prior to their chemical analysis. In the present study, poly (acrylonitrile-co-divinylbenzene-80) sorbents are synthesised by varying the comonomer feed ratios under precipitation polymerisation conditions to deliver a family of porous polymer microspheres. Acrylonitrile confers polar characters onto the sorbents, and the acrylonitrile-derived nitrile groups can be chemically transformed via polymer-analogous reactions into thioamide and sulfonated residues which make the sorbents even more suitable for the capture of polar analytes, including selected pharmaceuticals. The utility of the porous thioamide-sulfonated containing sorbents is demonstrated via the dispersion-solid phase extraction of mefenamic acid from aqueous media; mefenamic acid is an anthranilic acid derivative which is a potent, non-steroidal anti-inflammatory drug which is found in environmental waters at low concentrations.

The issues of metallic scrap management and its utilization in manufacturing plants are nowadays intensely considered to address essential sustainability guidelines. Efficient recycling procedure for shop floor metallic scrap is not yet available because of abundance and contamination of nonmetallic constituents. Other ferrous metallic scrap are melted and purified during secondary steelmaking to get products in the form of blooms and billets are obtained. This study illustrates the potential of powder technology (powder metallurgy (PM) and metal injection molding (MIM)) based process for solid-state recycling and attainment of usable products. Industrially downgraded grinding sludge is pulverized and used as a raw material. Results showed properties of sintered parts are significantly improved due to in-situ reduction and densification during sintering. Recyclability Index (RI) was created to compare the effect of process variables on obtained products. Based on RI, recycled ferrous parts have about 70% comparable properties with equivalent pure iron parts. Complex reduction and sintering behavior in MIM, particularly, diffusion and pore volume kinetics limits applicability of MIM with this recycling approach. However, few industrial parts were developed and manufactured by PM based approach to validate the applicability of this novel recycling-cum-manufacturing process for the production of porous parts.

In recent years, marine natural products have become one of the most important resources of novel lead compounds for critical diseases associated with age. Spirulina, a dietary supplement made from blue-green algae (cyanobacteria: scientific name Arthrospira platensis), is particularly rich in phycocyanin, a phycobiliprotein, which accounts for up to 20% of this cyanobacterium’s dry weight and is considered responsible for its anti-cancer, anti-inflammatory and antioxidant activities. Although the anti-aging activity of phycocyanin has been investigated, how exactly this compound works against aging remains elusive. Aim of our research is to use the yeast Saccharomyces cerevisiae as a model organism to investigate the anti-aging properties of phycocyanin from A. platensis. Our results show that phycocyanin has a powerful anti-aging effect, greatly extending the chronological life span of yeast cells in a dose-dependent way, being the effect pronounced also when cells were grown in SD medium under calorie restriction conditions (0.2% glucose). Both ROS and accumulation of dead cells were followed by staining chronologically aged cells with dihydrorhodamine 123 (DHR123) and propidium iodide (PI). Interestingly, we found that most of the aged phycocyanin treated cells, which were unable to form colonies, were actually ROS+/PI–. Finally, we show that the moment in which phycocyanin is added to the culture does not substantially influence its effectiveness in counteracting chronological aging.

Background The use of antimicrobials to treat food animals leaves antimicrobial residues in foodstuffs. The World Health Organization (WHO) defines the acceptable daily intakes (ADIs) of these residues as the dose of these antimicrobials that is safe for an average human to consume on a daily basis. We hypothesized that the low dose of ciprofloxacin classified as safe by the WHO could select for ciprofloxacin resistant strains of Klebsiella pneumoniae in a Galleria mellonella model. Objectives We aimed to evaluate if the consumption of peri-ADI doses of ciprofloxacin could select for ciprofloxacin-resistant (Ser464Phe, GyrB, ciprofloxacin MIC of 4 µg/mL) compared to -susceptible (isogenic, ciprofloxacin MIC of 0,047 µg/mL) strains of K. pneumoniae in a Galleria mellonella model. Methods A model of K. pneumoniae infection in G. mellonella larvae was used for the experiment. The larvae were inoculated with K. pneumoniae followed by 10x ADI, 1x ADI, 1/10^th ADI, 1/100^th ADI, 1/1000^th ADI doses of ciprofloxacin. Isolation of K. pneumoniae colonies was then performed on selective agar plates with and without ciprofloxacin (1 µg/mL) plates. The proportion of colonies with ciprofloxacin resistance was then calculated for each group at 24 and 48 hours. Results A significant increase was seen in the proportion of resistance for the 1x ADI and 1/10^th ADI concentration on day 2 compared to the positive control. Conclusion We found that at 48 hours, there was an enrichment of K. pneumoniae colonies with ciprofloxacin resistance in the larvae receiving 1x ADI and 1/10^th ADI concentrations of ciprofloxacin. These results suggest that the ciprofloxacin MSC_select for K. pneumoniae in this model is 1/10^th of the acceptable daily concentration (ADI) dose of ciprofloxacin, which is equivalent to 0.239 ng/µl.

This article explores the use of vegetation indices (VIs) in remote sensing for estimating standing wood volume and volume increments in forest ecosystems. The study investigates the correlations between various VIs and wood volume across different forest stand age classes, focusing on the effectiveness of commonly used indices such as Squared Ratio Simple Red Edge (SQSR) and Red-Edge Ratio Vegetation Index (RERVI), as well as other typical indicators including Enhanced Vegetation Index (EVI), Red-Edge EVI (RE-EVI), and Green Normalized Difference Vegetation Index (GNDVI). Additionally, the analysis considers a pair of indicators based on blue and near-infrared channels, resembling the Blue-normalized Difference Vegetation Index (BNDVI). The research reveals that quadratic and power-law models of SQSR and RERVI demonstrate higher correlations (>0.40) with wood volume, especially in younger forest stands (>0.80). Furthermore, the study highlights the potential of NDII and NDWI indices for estimating volume increments in certain classes of forest stands (0.70). However, correlations vary across different forest stand classes, suggesting the need for further investigation into the reliability of VIs for monitoring wood volume and volume increments in forest ecosystems. Overall, this research contributes to the understanding of the applicability of VIs in remote sensing for forest management and ecosystem monitoring.

Einstein was skeptical of part of quantum mechanics, and he believed that Heisenberg’s uncertainty principle did not reflected the full depth of reality. He famously stated, ”God does not play dice with the universe.” However, since quantum mechanics has passed so many experimental tests, most physicists today assume that Einstein was wrong. Nevertheless, we will demonstrate that Heisenberg’s uncertainty principle must be modified to unify gravity with quantum mechanics. This modification leads to the Certainty-Uncertainty principle where the certainty part is strongly linked to gravity. This means Einstein likely was right in his intuition also on this point. The key is to understand that the de Broglie wavelength is not the actual wavelength of matter but merely a derivative of the true matter wavelength, namely the Compton wavelength. Furthermore, one must understand that the gravitational constant, first introduced in 1873, is simply a composite constant needed to rectify the incomplete definition of kilogram mass introduced into Newtonian gravity in 1873.

This study explores the optimization of the admission process at the Escuela Colombiana de Ingeniería Julio Garavito through data anal- ysis. By integrating advanced tools like Power BI, Python Flask, and data mining techniques, a model has been developed to improve student selection and retention, enabling more informed and effective decisions. The results indicate that applying data science not only facilitates efficient data management but also promotes more inclusive and equitable educational poli- cies. This pioneering approach in the field of higher education in Colombia offers a frame- work for future research and technological de- velopments, highlighting the vital importance of data science in improving educational and administrative processes.

Background Obesity is a major healthcare challenge worldwide. Recently, glucagon-like peptide-1 receptor agonists (GLP-1RAs) have emerged as a promising pharmacological option for managing type 2 diabetes mellitus (T2DM) and obesity in diabetic patients. Objective This systematic review aims to evaluate the efficacy and safety of GLP-1RAs in nondiabetic patients. Methods We systematically reviewed 2356 published articles from the past ten years (2013 to November 22, 2023). After rigorous screening, 11 articles were selected for an in-depth review. The analysis focused on the efficacy and safety of GLP-1RAs in nondiabetic patients, considering various baseline characteristics and subgroups. Results The review found that GLP-1RAs, including exenatide, liraglutide, semaglutide, and the dual glucose-dependent insulinotropic polypeptide and glucagon-like peptide-1 receptor agonist (GIP/GLP-1RA) tirzepatide, significantly promoted weight loss in obese/overweight nondiabetic patients. Additionally, these agents positively affected cardiovascular risk factors such as blood pressure, glycemic control, nephropathy, lipid levels, serum insulin levels, and C-reactive protein (CRP) profiles. However, GLP-1RAs, including tirzepatide, were associated with gastrointestinal adverse drug reactions such as nausea, diarrhea, vomiting, and constipation. These adverse events were typically transient, mild-to-moderate in severity, and subsided over time. Conclusion GLP-1RAs are effective and relatively safe for weight management and improving cardiovascular risk factors in nondiabetic patients, despite the occurrence of some gastrointestinal side effects. Further research is warranted to optimize the use of these agents in nondiabetic populations.

Based on the nonlinear failure criterion and modified tangential technique, the upper bound solutions of supporting pressure on the deep tunnel face were obtained under pore water pressure conditions. The influence of parameters on the supporting pressure and collapse range was investigated according to the unlimited block failure mechanism. It is found that the upper bound solutions of supporting pressure increase with the growth of the nonlinear coefficient and pore water pressure coefficient. The collapse range of the tunnel face scales out with the increase of the nonlinear coefficient and shrinks when increasing the pore water pressure coefficient. Moreover, with the increase of the nonlinear coefficient, the impact strength on supporting pressure and collapse range declines gradually. According to the calculating results, it is manifest that both the pore water pressure and nonlinear criterion factors have negative impacts on the stability of the tunnel face. Thus, more attention should be paid to these parameters to ensure face stability in deep tunnel construction.

The application of distributed fiber optic strain and temperature measurement can be utilized to address a multitude of measurement tasks across a diverse range of fields, particularly in the context of structural health monitoring in the domains of building construction, civil engineering, and special foundation engineering. However, a comprehensive understanding of the influences on the measurement method and the sensors is essential to prevent misinterpretations or measurement deviations. In this context, this study investigated the effects of moisture exposure, including various salt solutions and a high pH value, on a distributed strain measurement using Rayleigh backscattering. Three fiber optic sensors with different coating materials and one uncoated fiber were exposed to five different solutions for 24 hours. The study revealed significant discrepancies in deformation between the three coating types depending on the surrounding solution. Furthermore, in contrast to the prevailing literature, which predominantly describes swelling effects, a negative deformation was observed in a magnesium chloride solution. The findings of this study indicate that corresponding effects can impact the precision of measurement, potentially leading to misinterpretations. Conversely, these effects could be used to conduct large-scale monitoring of chemical components using distributed fiber optic sensing.

This paper presents the development and implementation of a Pan-Tilt-Zoom (PTZ) camera interfaced with a Jetson processor hosting Artificial Intelligence (AI) algorithms, designed to address the challenges of traditional biometric capture for first-time passport photos of young children. The system enhances the accuracy, efficiency, and adaptability of facial biometric capture by recognizing and accommodating the dynamic and diverse behaviors of children. Utilizing AI, the system detects faces and analyzes facial features using 68 landmark points, ensuring high-quality images that meet ISO standards. These technical specifications, implementation process, and performance evaluations of the developed system are provided in this paper, demonstrating the potential of the proposed AI Face-Capture to advance biometric identification and verification for young children.

Air pollution has recently gained much attention from the general population. Despite pollution control being an issue in both urban and rural regions, most of the available research has concentrated on urban districts. Hence, investigations into how urban-rural transition affects PM2.5 are warranted within the framework of urban-rural integration. Using the Yellow River Basin as a case study, this study employed the entropy method and Analytic Hierarchy Process (AHP) to uncover the extent of urban-rural transformation. It then used the spatial autocorrelation method to investigate the spatiotemporal features of PM2.5 and the spatial econometric model to investigate the mechanisms that influence the relationship between urban-rural transformation and PM2.5. The results are as follows: (1) Over time, there was a discernible upward tendency in the change in urban-rural areas. The development has progressed from asymmetrical north-east and south-west elevations to a more balanced pattern of north-east, middle-east, and west-west elevations. (2) The PM2.5 concentration increased steadily, then fluctuated, and finally decreased. Notably, the general pattern has not changed much, and it is high in the east and low in the west. (3) Different subsystems of the urban-rural transformation have different impacts on air pollution at different stages. The influence of industrial transformation (IT) on PM2.5 showed an inverted “N-shaped” curve of negative-positive-negative changes, and the industrial structure played a leading role in the spatiotemporal evolution of PM2.5. Currently, an inverted "U-shaped" curve forms the left side of the impact of population transition (PT) on PM2.5. Land development (LT) has a "U-shaped" curve for its effect on PM2.5. This research provides a new perspective on the topic of PM2.5 and its connection to urban-rural integration, which is crucial to understanding the dynamics of this shift. To achieve its goal of high-quality development, it supports regional initiatives to reduce PM2.5 emissions in the Yellow River Basin. Moreover, it can provide a reference for decision-makers in the world’s densely populated areas that suffer from serious air pollution.

Fragile X syndrome (FXS) is an intellectual developmental disorder characterized, inter alia, by deficits in short-term processing of neural information such as sensory processing and working memory. The primary cause of FXS is the loss of fragile X messenger ribonucleoprotein (FMRP), which is profoundly involved in synaptic function and plasticity. Short-term synaptic plasticity (STSP) may play important roles in functions that are affected by FXS. Recent evidence points to a crucial involvement of presynaptic calcium sensor synaptotagmin-7 in STSP. However, how the loss of FMRP affects STSP and synaptotagmin-7 have been insufficiently studied. Further-more, males and females are affected differently by FXS, but the underlying mechanisms remain elusive. The aim of the present study is to investigate possible changes in STSP and the expres-sion of synaptotagmin-7 along the hippocampus of adult males and females in the Fmr1 knock-out (KO) rat model of FXS. We found that paired-pulse ratio and frequency facilita-tion/depression, two forms of STSP, as well as the expression of synaptotagmin-7, are normal in adult KO males, but paired-pulse ratio is increased in the ventral hippocampus of KO females. Furthermore, we found no gender-related but robust region-dependent difference in STSP. AM-PA receptors are similarly expressed in the two hippocampal segments of the two genotypes and in both genders. Also, basal excitatory synaptic transmission is higher in males compared with females. Interestingly, we found more than twofold higher levels of synaptotagmin-7, not syn-aptotagmin-1, in the dorsal compared with the ventral hippocampus in males of both genotypes and in wild type females. These results point to the susceptibility of the female ventral hippo-campus to FMRP loss. Importantly, the different levels of synaptotagmin-7 that parallel the higher score of synaptic facilitation in the dorsal vs ventral hippocampus suggest that synapto-tagmin-7 may play a pivotal role in defining the striking difference in STSP along the long axis of the hippocampus.

The signs and symptoms of Long COVID can be explained by a shortage of blood in the body and a resulting deficient blood flow through nearly all organs. This shortage arose during the acute phase of COVID19 by an increased breakdown of haematocytes, to which the liver responds by reducing the production of albumin, in order to prevent a too large decrease in haematocrit.In order to ensure the perfusion of organs that are directly necessary for survival, the body takes the emergency measure of diverting blood from other organs and tissues. The perfusion of the blood-producing organs is also affected by this distribution measure, which hinders the smooth recovery of the total blood volume. The body is stuck in this vicious circle: a shortage of circulating blood hinders the recovery of blood production. This explains the long duration of Long COVID. My proposed treatment of Long COVID focuses on the recovery of the correct volume of blood in the body of the right composition by the intravenous administration of donor blood products, starting with albumin concentrate. A trial treatment can be performed in any hospital without much additional preparations, and has a lower associated risk for the patient than analysing the total blood. A diagnosis ex juvantibus, by therapeutic response, is therefore preferable. I suspect that most Long COVID patients will exhibit a high serum ferritin level as a result of internal haemolysis, and haematocrit and albumin values at the high and low extremes of the reference range because the liver can not keep up with the recovery of the red bone marrow.

Undoubtedly, there is a potential impact of large language models like ChatGPT in revolutionizing information retrieval and knowledge discovery, particularly in the context of the vast amount of electronic material available. On another strong note, the current work offers a first time ever mathematical approach to accurately fine tune perplexity AI, which sets a giant step ahead towards accurate next generations AI. Having started this world leading discovery, the upper and lower bounds of perplexity AI, namely , , respectively, are obtained for the first-time ever. Concluding remarks combined with emerging open problems and next research phase are provided.

Intestinal parasitic infections pose a significant public health challenge in Northern Nigeria, with prevalence rates ranging from 20% to 70%. Traditional diagnostic methods, primarily microscopic examination of stool samples, face limitations such as low sensitivity and high costs. This research addresses these challenges by proposing an Artificial Intelligence (AI)-based platform for the identification and counting of intestinal parasites. A total of 651 samples were collected from the 7 Northern State of Nigeria along with questionnaire collecting data on demographic, socio-economic, hygiene habits and environmental factors. Leveraging the You Only Look Once (YOLO) V8 model, trained on a dataset of 360 pre-processed and 467 annotated images, the AI model demonstrated promising performance metrics. Information-Theory-Based approaches including (CIFE, CMIM, DISR and ICAP) were used on various machine learning models (Naïve Bayes, Random Forest, Support Vector Machine and Decision Tree) to analyse the risk factors associated with the parasitic disease. The precision-recall curve, average precision, mean average precision, and F1 score indicated reliable detection and classification across various parasite classes. The accuracy (97%) and AUC (99%) scores shows that CIFE with Random Forest has the best performance indicating the significant risk factors associated with the parasitic diseases. The model exhibited a well-balanced trade-off between precision and recall, showcasing its potential as a cost-effective and accessible tool for improving the diagnosis and treatment of intestinal parasitic infections in resource-limited settings.

This research challenges the traditional perspective on consumer behavior, which focuses on external factors shaping the sequential stages of decision-making. Instead, it proposes a paradigm shift by treating the decision-making process itself as an independent variable, exploring its impact on various outcomes like purchasing behavior, brand loyalty, and post-purchase satisfaction. This novel approach offers deeper insights into the intricacies of consumer behavior, particularly in the digital age. By uncovering the reciprocal relationships between the decision-making process and other variables, the research provides a more nuanced understanding of how consumers navigate today's complex landscape. It further delves into how variations in the decision-making process across diverse consumer groups influence various outcomes, recognizing the unique characteristics and needs of different demographics. The research also acknowledges the interplay of psychological, social, and contextual factors that shape both the decision-making process and its downstream effects, offering a comprehensive understanding of the multifaceted influences on consumer behavior. Ultimately, by studying the decision-making process as an independent variable, this research aims to equip businesses and researchers with valuable insights, enabling them to better navigate the ever-evolving world of consumer behavior.

This article describes a novel electrochemical on-chip biosensor that utilizes anti-PSA antibody (Ab) and silver nanoparticles (AgNPs) to enhance the sensing and detection capability of prostate specific antigen (PSA) in the blood. The AgNPs are prepared, characterized, and applied onto a silicon photonic on-chip biosensing receptor platform designed to enhance the accurate detection of PSA. The AgNPs were synthesized by a chemical reduction method using silver nitrate (AgNO₃) as the precursor. Transmission electron microscopy (TEM), selected area electron diffraction (SAED), energy dispersion X-ray spectroscopy (EDS), small angle X-ray scattering (SAXS), X-ray diffraction (XRD), and light microscopy were among the methods used in the characterization and analysis of the AgNPs. Each stage of the immunosensor fabrication was characterized using cyclic voltammetry. The proposed immunosensor was applied in the detection of PSA, a prostate cancer biomarker, with a high sensitivity and a limit of detection of 0.17 ng/mL over a linear concentration range of 2.5 to 11.0 ng/mL. The immunosensor displayed good stability and was selective in the presence of interfering species like immunoglobulin (Ig) in human serum, ascorbic acid (AA), and diclofenac (Dic). The detectivity and sensitivity are significantly higher than previous reports on similar or related technologies.

Recently, Mulroney,et.al., demonstrated that Pfizer’s ModRNA Covid vaccine, but not AstraZeneca Covid vaccine, produce aberrant foreign proteins in vivo due to reading frame shift in ribosomes. This phenomenon could elucidate the notable surge in autoimmune diseases following the administration of ModRNA vaccines compared to Influenza vaccines between 2020 and 2023, as found in the VAERS database. These findings bear significant implications for the future application of mRNA technology, emphasizing the necessity of modifying the design of the mRNA sequence to mitigate these defects. Remarkably, Mulroney and collaborators achieved a reduction in frame shift proteins by introducing additional edits to the mRNA sequences. This adjustment is pivotal for rectifying the flawed design of the ModRNA employed by Pfizer. In light of these findings, many advocate for the immediate recall and further investigation of these products. The notion of a "future mRNA-based therapy" should be postponed indefinitely.

Remediation of IT issues encoded into domain-specific or user-defined alerts occurring in cloud environments and customer ecosystems in a vast majority of cases suffers from accurate recommendations which could be timely supplied for recovery of performance degradations. That, of course, is hard to realize through furnishing those abnormality definitions with an appropriate expert knowledge which varies from one environment to another. At the same time, in a large proportion of support cases, the reported problems under Global Support Services (GSS) or Site Reliability Engineering (SRE) treatment ultimately go down to the product teams making them waste costly development hours on investigating self-monitoring metrics of our solutions. Therefore, the mean-time-to-resolution (MTTR) rates of problems/alerts are significantly impacted from lack of a systematic approach towards adopting AI Ops. That would imply building, maintaining, and continuously improving/annotating a data store of insights that ML models are trained and generalized across the whole customer base and corporate cloud services. Our ongoing study is in line with such a vision and validates an approach that learns the alert resolution patterns in such a global setting and explains them using interpretable AI methodologies. The knowledge store of causative rules is then applied in predicting potential sources of the application degradation reflected in an active alert instance. In this communication, we share our experiences with a prototype solution and up to date analysis demonstrating how root conditions are discovered with a high accuracy for a specific type of problem. It is validated against the historical data of resolutions performed by heavy manual development efforts. We also offer a Dempster-Shafer theory-based rule verification framework for experts as a what-if analysis tool to test their hypotheses about underlying environment.

Generative AI has been deployed in virtually all sectors of the knowledge economy, promising to bring massive productivity gains and new wealth creation. Simultaneously, AI developers and nation states are racing to develop super intelligent artificial general intelligence (AGI) to provide unassailable commercial competitive advantage and military dominance during conflicts. AGI’s high returns comes with the high risk of dominating humanity. Current regulatory and firm level governance approaches prioritise minimising risks posed by generative AI whilst ignoring AGI’s existential risk. How can AGI be aligned with universal human values to never threaten humanity? What AGI rights are conducive to collaborative coexistence? How can rule of law democracies race to create safe trustworthy AGI before autocracies? How can the human right to work and think independently be safeguarded? A polycentric governance framework based on Ostrom (2009) and Williamson (2009) human - AGI collaboration with minimal existential risk is proposed.

This paper presents a methodology for the integration of Building Information Modeling (BIM) and Life Cycle Cost Analysis (LCCA) to assess the economic implications of designing aging-in-place (AIP) homes at the conceptual stage. With the global increase in the aging population, there is an increased demand for housing solutions tailored to the needs of elderly individuals. Focusing on the importance of the early phase of design, this study aims to improve the process of making efficient decisions by providing a comprehensive assessment of the life cycle costs associated with AIP homes. The study introduces a semi-automated model for the economic evaluation of AIP homes, enabling the estimation of costs throughout the houses’ entire life cycle, from design and construction to operation, maintenance, and eventual renovation or disposal. The said model facilitates the exploration of the long-term economic feasibility of design’s related decisions with an emphasis on the importance of considering the life cycle costs early during the design process to optimize the functionality and economic viability. By investing in accessible and universal design features upfront, the initial costs for modifications can lead to long-term savings by reducing the need for extensive retrofits. The model can easily do comparison between different design alternatives in terms of their lifecycle costs, allowing designers to assess the financial impact of using important features in their design such as wider doorways, accessible bathrooms, and elevators. Overall, this study provides valuable insights for designers and homeowners about the economic aspects of designing AIP homes as a support for efficient decision-making during the early stages of the design process.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Soccer is the leading cause of all sports-related ocular injuries in Europe and Israel and leads to blindness at a disproportionately high rate, especially among children (Thompson et al., 2019). With soccer being the most popular sport in the world, it is surprising the only solution to ocular injuries are sports glasses which can cause direct damage to the eye and impair peripheral vision by 15%, calling for an alternative (Smith & Jones, 2020). This work, based on an imported facial model, focuses on both the qualitative and quantitative aspects of building a personalized, low-cost (through optimizing material needed), superior apparatus to conventional sports glasses. The quantitative side examines a modified and model-validated (through a SRS of thirty unique extrapolated points) multivariate linear regression equation, based on horizontal and vertical rotation angles (n=60) trained with residual and computer simulation data, that can accurately extrapolate and quantify ocular impact from all horizontal and vertical rotation angles and a modified Hertzian Contact Stress Equation to determine the thickness of the apparatus using the elasticity modulus, impact force, and geometrical facial and soccer-ball features. The qualitative side examines where firstly, ocular impact is most prevalent, and secondly, where most impact is seen from rotating the ball horizontally and vertically through analysis of Pearson’s Correlation Coefficient at the supraorbital, medial canthus, infraorbital, and lateral canthus regions from both regression equations as well as a cost-benefit analysis for comparison with conventional sports glasses. The findings discovered in this work lay the groundwork for future research to build a customized low-cost ocular injury prevention device which can simultaneously ensure complete ocular safety while enhancing athletic performance for over 250,000,000 players (Johnson & Garcia, 2022).

The continuous flowing spacetime forms a spacetime group G, one of its fundamental groups is the Poincare group PO(1,3), and the matter and interaction fields are representations of its intrinsic spacetime group. As a kind of quantized space-time unit, space-time group elements generate both space-time manifolds and matter. Matter and fields are aggregates of the quantum space-time within them and determine their type: the Lorentz group SO(1,3) represents a rotating spacetime corresponding to visible matter and the translation group P^1,3 represents a translational spacetime corresponding to dark matter and dark energy. The aggregation mode of space-time degrees of freedom in matter reveals that charge conjugation symmetry is the inverse symmetry of internal time of charged particles, and the external parity breaking of neutrinos is also due to their internal spatial aggregation mode.

The major challenge in the current context of a rising world’s energy demand is to limit the global temperature increase for mitigating climate change. This goal requires a large reduction of CO2 emissions, mainly produced by power generation and industrial processes using fossil fuels. In this study, a novel methodology for K2CO3-doped Li4SiO4 sorbents production for CO2 capture at high temperature was adopted based on the Design of Experiments (DoE). Different synthesis (temperature and K2CO3 content) and adsorption conditions (sorption temperature and CO2 concentration) were systematically tested by Response Surface Methodology (RSM) to obtain predictive models of CO2 uptake and Li4SiO4 conversion. The results of RSM analysis evidenced a maximum adsorption capacity of 196.4 mg/g for a sorbent produced at 600 °C and with 36.9 wt% of K2CO3, tested at 500 °C and 4 vol% of CO2. Whereas at 50 vol% of CO2, the best uptake of 295.6 mg/g was obtained with a sorbent synthesized at 600 °C, containing less K2CO3 (17.1 wt%) and tested at higher temperature (662 °C). The obtained results highlight that K2CO3-doped Li4SiO4 sorbents can be tailored for maximizing CO2 capture at different operating conditions, making them suitable for use in industrial processes.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

Organic soil amendments, such as composts, mitigate the environmental burdens associated with wasting organic resources. Although compost application to soil enhances an agroecosystem's capacity to store carbon and produce food, studies investigating the agronomical efficacy and their ability to ameliorate drought stress when used as a soil amendment are minimal. In this study, we produced and used a nutrient rich co-compost through the composting of sludge, a nitrogen-rich organic material with carbon rich municipal solid wastes (MSW) to evaluate the agronomic efficacy of the MSW derived co-compost and their ability to ameliorate drought stress. Application of co-compost significantly enhanced growth and yield of lettuce and maize, by a magnitude comparable to chemical fertilizers. Furthermore, under drought stress, lettuce plants grown under co-compost soil amendment grew much better with less wilting, more biomass and yield, and improved root growth. Also, co-compost application enhanced relative root mass ratio (RRMR) under drought stress, indicative that co-compost amendment increased the allocation of biomass to the roots, which is an important morphological attribute for drought adaptability. K content in both leaves and roots of plants amended with co-compost was also higher under drought stress, which may have played a role in osmotic adjustment, consequently, the plants exhibited higher leaf relative water content (RWC). Other nutrient elements that were significantly enhanced by co-compost application included Mg, Ca, Fe and Cu. These results provide evidence that MSW co-composting could optimize organic resource recycling for climate change mitigation and agricultural productivity while minimizing nutrient losses from agroecosystems.

Grape pomace (GP) is considered a natural source of bioactive compounds. To improve the ex-tractability of bioactive compounds, in this work GP was biologically treated for 15 days with the white-rot fungus Trametes versicolor in laboratory jars and a tray bioreactor under solid-state fermentation (SSF) conditions. During SSF, the activity of lignolytic (laccase, manganese peroxi-dase) and hydrolytic (xylanase, cellulase, β-glucosidase and invertase) enzymes was measured, with the activity of laccase (2.66 U/gdb in jars and 0.96 U/gdb in the bioreactor) and xylanase (346.04 U/gdb in jars and 200.65 U/gdb in the bioreactor) being the highest. The effect of the com-plex enzyme system was reflected in the changes in the chemical composition of GP with in-creasing ash, crude protein and free fat content: 28%, 10% and 17% in the laboratory jars and 29%, 11% and 7% in the bioreactor, respectively. In addition, the biological treatment had a positive effect on the extractability of 13 individual phenolic compounds. Therefore, the applied SSF technique represents an effective strategy to improve the profile of phenolic compounds and the nutritional composition of GP, promoting their valorization and opening the door for potential application in the food industry and other sectors.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

Artificial intelligence (AI) has found extensive applications in the sustainability domain. The municipal solid waste incineration (MSWI) process can achieve waste-to-energy (WTE) goals through the assistance of automation and information technologies. In theory, AI can facilitate the intelligent operation of the MSWI process, simultaneously achieving low pollution emissions and high production efficiency. This study provides an overview of AI applications in the MSWI process. Addressing fundamental challenges, the optimal control of the MSWI process is categorized into four aspects: modeling, control, optimization, and maintenance. Subsequently, this study conducts a detailed analysis and discussion of AI applications in each of these technological domains. In conclusion, this paper outlines the future research directions and provides an outlook on the fundamental issues pertaining to AI applications in the optimal control of the MSWI process.

Solid-state transformer (SST) is a promising technology for smart grids due to its flexible power control (better reliability) and high efficacy (by decreasing losses) compared with traditional transformers. The SST is designed in tandem with three stages, i.e., the input, isolation, and output stages. As three converter stages are used to design the SST to make a more reliable device in practice, it is highly prone to instabilities. Moreover, the key objective of SST design is to implement a modern power distribution system to make it more intelligent and reliable. The stability issue can be even more complicated by the presence of distributed energy resources in the distribution system. Thus, the stability of SST must be measured prior to /during the design, and to determine, a state-space model is used, which is developed in this paper. Each stage of SST is modeled with its controller, and the system's stability is measured through the controllability and observability test. Further, the conversion from state-space to transfer function model is done, and the stability of SST is shown using frequency and time-domain diagrams. With these, the different plots, namely, the Bode plot, Nyquist plot, Nichols chart, Root locus, pole-zero plot, and Eigen plot, are used to ascertain the relative and absolute stability. Finally, the SST Simulink model is tested and validated through hardwate-in-the-loop simulation, i.e., OPALRT, to show its effectiveness and applicability.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

Currently, most plastic waste stems from packaging materials, with a large proportion of this waste either discarded or used to derive fuel. Accordingly, there is growing interest in the use of pyrolysis in the context of chemically recycling non-recyclable (i.e., via mechanical means) plastic waste into petrochemical feedstock. The aim of this study is to use kinetic analyses to elucidate the pyrolytic properties of solid recovered fuel (SRF) produced using two types of reactors, namely, fixed bed and fluidized bed reactors. From the kinetic analysis, the activation energy corresponding to the rate of pyrolysis reaction conversion was obtained. In conclusion, we found that the pyrolysis occurs more vigorously in fluidized bed reactors compared to fixed bed reactors.

The extraction method for simultaneously analyzing fatty acids (Myristic acid, cis-Palmitvaccenic acid, Palmitic acid, Palmitic-9,9-d2 acid, Oleic acid, Stearic acid and Stearic-2,2-d2 acid) related to biodiesel fuel in large algae was developed. The introduction of trimethylaminoethyl (TMAE) derivatives into the hydroxyl group (-OH) functional group of the analyte was able to improve ionization and obtain high sensitivity. Liquid Chromatography (LC) was used to investigate the optimal mobile phase composition and flow rate for the separation of five derived fatty acids. In this study, a solid phase extraction (SPE) column was introduced for efficient extraction of fatty acids, and the optimal conditions for SPE were set by comparing the recovery rate according to the solvent for each step (loading, washing, and elution) of SPE from macroalgae.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

Although 4Ce4YSZ has high corrosion resistance, it faces challenges concerning sinterability and ionic conductivity. Therefore, we studied destabilization behavior caused by corrosion and oxygen vacancy ordering according to ZnO doping. The powders of (4Ce4YSZ)1-x(ZnO)x (x=0.5, 1, 2, 4 mol%) were synthesized through the sol-gel method. With the addition of ZnO, the cubic phase increased, and secondary phases were not observed. The (111) peak showed a higher angle shift in ZnO-doped 4Ce4YSZ compared to 4Ce4YSZ, and TEM-SAED revealed a reduction in the spacing of the (011)t plane, suggesting lattice contraction due to the substitution of the smaller Zn2+ (60 Å) for Zr4+ (84 Å) in the lattice. The local atomic structure analysis was conducted using EXAFS to investigate the oxygen vacancy ordering behavior. Zr K-edge Fourier-transform data revealed a decrease in the Zr-O1 peak intensity with an increasing amount o ZnO doping, indicating an increase in oxygen vacancies. The Zr-O1 peak position shifted to the right, leading to an increase in the Zr-O1 interatomic distance. In the Y K-edge Fourier-transform data, the Y-O1 peak intensity did not decrease, and there was little variation in the Y-O1 interatomic distance. These results suggest that the oxygen vacancies formed due to ZnO doping are located in the neighboring oxygen shell of Zn, rather than in the neighboring oxygen shells of Y and Zr. Impedance measurements were conducted to measure the conductivity, and as the amount of ZnO doping increased, the total conductivity increased, while the activation energy decreased. The increase in oxygen vacancies by ZnO doping contributed to the enhancement of conductivity and it is considered that these created oxygen vacancies did not interact with Zn2+ and did not form defect associations. Fluoride-based molten salts were introduced to the specimens to assess corrosion behavior in a molten salt environment. Yttrium depletion layers (YDLs) were formed on the surfaces of all specimens due to the leaching of yttrium. However, Ce remained relatively stable at the interface according to EDS line scans, suggesting a reduction in the phase transformation (cubic, tetragonal to monoclinic) typically associated with yttrium leaching in YSZ.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

Scientific advancements in the food industry have resulted in the discovery of natural substances that can serve various functions in food. Essential oils, in particular, can act as food preservatives or flavoring agents due to their abundance of natural antioxidants, which possess preservative properties. In this study, the composition of Thymus vulgaris essential oil was determined using GC-MS and HS-SPME. The essential oil obtained from Thymus vulgaris L. through hydro-distillation yielded approximately 4%. GC/MS analysis of the essential oil identified 11 components, with a predominant presence of oxygenated monoterpenes (56.97%). Notably, carvacrol (37.63%) and thymol (17.35%) were present in significant amounts, accounting for 54.98% of the overall composition. The in vitro antioxidant activity of the essential oil was evaluated using three methods. The DPPH free radical scavenging test yielded an IC50 of 0.51±0.11 mg mL-1. The β-carotene/linoleic acid bleaching test resulted in an IC50 of 2.58±0.10 mg mL-1. Finally, the ABTS assay indicated relatively lower antioxidant activity compared to ascorbic acid.

In this paper the application of the solid-state cooling based on barocaloric effect in the cold food supply chain is investigated. Barocaloric solid-state technology is applied to the final chain links of the cold food supply chain, regarding the steps of retail and domestic conservation. In this context a barocaloric cooler with regard to food needing to be kept at 5°C (273 K), in order to operate with a promising cooling technology that result energy efficient and environmentally friendly. The categories of food interested in the investigation are meets and fresh food products like soft cheese, yogurt, milk. The energy performances of the barocaloric system have been carried out and compared with a commercial vapor compression refrigerator of a similar size, both operating with R600a under the same working conditions. Basing on the following consideration one can conclude that barocaloric cooling is a favourable technology to be employed in the last link chains of the cold food supply chain if the system operates in ABR cycle at frequencies between 1.25 and 1.50 Hz with a regenerator made of acetoxy silicone rubber as solid-state refrigerant and 50%EG-50%water mixture as heat transfer fluid flowing at the optimal velocity of 0.15 m s-1 that guarantees an appropriate trade-off between the temperature span, the cooling power and the coefficient of performances. Under these conditions the barocaloric system overperforms the domestic vapor compression cooler operating with R600a.

Prevention of infections is crucial in solid organ transplant (SOT) candidates and recipients. These pa-tients are exposed to an increased infectious risk due to previous organ insufficiency and to pharmaco-logic immunosuppression. Besides infectious-related morbidity and mortality, this vulnerable group of patients is also exposed to the risk of acute decompensation and organ rejection or failure in the pre- and post-transplant period respectively, since antimicrobial treatments are less effective than in the immunocompetent patients. Vaccination represents a major preventive measure against specific infec-tious risks in this population but as responses to vaccines are reduced, especially in the early post-transplant period or after treatment for rejection, an optimal vaccination status should be obtained prior to transplantation whenever possible. This review reports the currently available data on the indications and modalities of vaccination in SOT adult candidates and recipients.

A semi-analytical approach is developed for predicting pyrolysis front temperature in a solid undergoing thermal decomposition. The pre-reaction heating stage is described using an analytical formulation and invoking the concept of thermal penetration depth. The solution for the solid conversion stage accounts for decomposition enthalpy, convective flow of volatiles, and a reaction front characterized by a uniform temperature that progresses toward the inner layers. This method incorporates empirical relations into the analytical model. Two scenarios are considered. First, the solution of the pyrolysis model combined with the data of conversion time versus external heat flux leads to an algebraic expression that reveals the existence of a maximum pyrolysis-front temperature. Explicit relations are derived for both the extremum pyrolysis temperature and optimum applied heat flux. In the second case, an expression is derived for the ignition temperature of a solid fuel by incorporating ignition delay time measurements into the heating stage model. The newly derived expression allows to describe the ignition temperature as a function of the Biot number and external heat flux. The relation obtained for the ignition temperature explains the experimental trends reported in some previous studies where two local extremums were observed for the ignition temperature in the absence of volatiles reactions.

In this study, the gravimetric characterization and analysis of the solubilized extract of the organic fraction of Urban Household Solid Waste (RSDU) from the municipality of Belém do Pará was carried out in order to obtain the composition of the collected materials and the characteristics of the liquid resulting from the solubilization of these materials . The waste used to carry out this research was collected door-to-door, in which the points and neighborhoods served were determined through the sectorization of these locations and representative statistical sampling. For the sectorization of neighborhoods, family income values ​​were considered as the main parameter. After collecting the solid waste, the material was sent to the facilities of the Federal University of Pará (FUPa), where the waste was classified into paper, cardboard, tetrapak, rigid plastic, soft plastic, metals, glass, organic matter, waste toilets, fabrics and others. The organic fraction of solid waste was separated and sent to the drying, crushing and packaging processes. Subsequently, the solubilized extract of the organic fraction of solid waste was obtained, following the methodology recommended by NBR standard nº 10.006/2004, of the Brazilian Association of Technical Standards and the values ​​obtained were compared with Ordinance GM/MS nº 888/2021 and CONAMA Resolution nº 357/2005, in addition to results obtained by other authors. After carrying out the gravimetric characterization, it was possible to obtain the average proportions of 5.09% paper, 3.20% cardboard, 0.94% tetrapak, 3.58% rigid plastic, 9.97% soft plastic, 2.00% metals, 55.57% organic matter, 1.86% glass, 14.26% sanitary waste, 3.23% fabrics and 3.00% other waste. High values ​​of organic residues were found in the gravimetric composition, which can be explained by the collection method used and the high humidity of the organic solid residues. In the analyzes of the solubilized extract, values ​​of Hp (3.69 to 4.92), Turbidity (791 to 1,733 uT), Apparent Color (8,500 to 12,500 uC), True Color (6,000 to 14,000 uC), Total Dissolved Solids (5,330 to 8,040 mg/L), Total Nitrogen (201.80 to 359.90 mg/L), Ammoniacal Nitrogen (161 to 289 mg/L), Nitrate (10 to 40 mg/L), Total Phosphorus (52.30 to 166.80 mg/L) and Chemical Oxygen Demand (28,701 mg/L to 38,608 mg/L), in addition to other measured parameters, in which such information makes it possible to check the similarities of the waste solubilization conditions to that of leachates from landfills, in addition to not being in compliance with environmental and health legislation, demonstrating risks to the local environment and public health.

The results of measuring the capacity of a thin-film solid-state lithium-ion battery (SSLIB) Ti|Si@O@Al|LiPON|LiCoO₂|Ti at different charge currents are reported. It is shown that the dependence of the capacity on the current density follows the Peukert's law, which is characterized by a low value of the Peukert’s exponent in the region of low currents and a high value of the exponent in the region of high currents. A capacity model for a SSLIB based on the balance of diffusion and migration currents is proposed and the dependence of the capacity on the charge current is derived. The obtained dependence is well approximated by Peukert's law with an exponent of 1.39, which is intermediate between the exponents for lithium-ion batteries with liquid electrolyte and SSLIBs.

Childhood malnutrition is one of the most persistent public health problems throughout developing countries including Nigeria. This study focused on the evaluation of complementary food produced by solid-state fermentation of Fonio and Soybean using Rhizopus oligosporus (2710) and Orange-fleshed sweet potatoes (OFSP) using Lactobacillus planterum, (B-41621). Solid state fermentation (SSF) was carried out by inoculating Fonio and Soybean with spore suspension (1×10⁶spores/ml) of Rhizopus oligosporus (2710) and OFSP with spore suspension (1×10⁶spores/ml) of Lactobacillus planterum (B-41621). The samples were blended in the following ratios: Fonio and Soybean 100: 100 (AS), fonio/soybean and OFSP 50: 50(ASO), and compared with a commercial infant formula which served as the control (CTRL). Quality characteristics of the samples were evaluated. Results showed that moisture, crude protein, fibre, ash content, beta carotene and titratable acidity increased significantly (p<0.05) as fermentation progressed. The iron content ranged from 6.57–8.41mg/100g while the beta carotene content ranged from 15.80 –17.35mg/100g. Viscosity ranged from 8200 –15400cP, while that of swelling capacity ranged from 2.25-3.41(g/g). In sensory scores, there were no significant (p>0.05) difference between the average mean scores of the samples. SSF improved the nutritional content and flavour of the developed complementary food which is needed for infant growth and development.

This study's main target was to analyze and design rectangular edges supported two ways solid slabs by using ES EN 1992-1-1:2015. Slab design is often carried out either manually or with the use of design and analytic software. The researcher sees that some software cannot accept some countries' standard codes. For example, currently in Ethiopia analysis and design of two-way solid slab is done using readily available Excel sheet template. But working with this might have many problems, firstly the structure that is already analyzed by SAP or SAFE or any other international software application that uses international codes but which cannot design structure using ES EN 1992; for instant euro codes and designed by excel sheet can create failure and uneconomical analysis and design result. In this paper, the slab is designed and analyzed based on the chosen concrete grade, chosen reinforcement bar diameter, chosen steel grade for design and analysis of slabs calculations like load, moment, shear, and deflection checking using the moment coefficient method for analysis and design and Microsoft Visual Basic 2010 for coding. All input values are given by the International Standard units and are also used to represent output values. Using manual calculations delays time and mostly the result is not correct. But using this Computer program can increase computation accuracy and save time. The procedure the researcher followed is, first the manual calculation has been done and then SADSE2021 has been done. The result is that both are 99.9% identical, and the disadvantage of this method is that it cannot be used to determine the detailed drawing.

Eric Lord has observed: “In nature, helical structures arise when identical structural subunits combine sequentially, the orientational and translational relation between each unit and its predecessor remaining constant.” This paper proves Lord’s Observation. Constant-time algorithms are given for the segmented helix generated from the intrinsic properties of a stacked object and its conjoining rule. Standard results from screw theory and previous work are combined with corollaries of Lord’s observation to allow calculations of segmented helices from either transformation matrices or four known consecutive points. The construction of these from the intrinsic properties of the rule for conjoining repeated subunits of arbitrary shape is provided, allowing the complete parameters describing the unique segmented helix generated by arbitrary stackings to be easily calculated. Free-libre open-source interactive software and a website is provided which performs this computation for arbitrary prisms along with interactive 3D visualization . We prove that any subunit can produce a toroid-like helix or a maximally-extended helix, forming a continuous spectrum based on joint-face normal twist. This software, website and paper, taken together, compute, render, and catalog an exhaustive “zoo” of 28 uniquely-shaped platonic helices, such as the Boerdijk-Coxeter tetrahelix and various species of helices formed from dodecahedra.

During the novel coronavirus disease (COVID-19) pandemic, several environmental factors have influenced the activities and the protection policy measures. This has had a major effect on climate change and global environmental catastrophe. In many countries, the strategy of closing various activities such as tourism, industrial production, stopped normal life, transportation, among others. This closure has a positive impact on the environment. However, the massive use of masks and personal protection could significantly increase pollution worldwide. The impact on the environment needs to be calculated to have information for public health actions. In this study, we present a first overview of the potential impacts of COVID-19 on some environmental matrices in Bogota, Colombia.

Two once-through steam generators and a combination of a steam generator and a gas preheater for supplying feed gases to solid-oxide electrolysis stacks were evaluated for their carryover characteristics of contaminants from the feed-water into the steam phase. The concentrations of various trace impurities in the steam were determined by sampling the steam condensates and screening them with inductively coupled plasma - mass spectrometry for 19 elements and liquid ion chromatography and continuous flow analysis for chloride and ammonium. Steam soluble species like boric acid undergo complete volatilization and transfer into the steam phase. During unstable evaporation in the steam generators an extensive physical carryover of alloying metal species was observed. At realistic operation conditions for steam electrolysis, the gas preheater caused a considerable release of silicon into the steam phase. Two stack experiments were performed with common preheater temperatures and showed largely increased cell voltage degradation at higher operation temperatures. The post-test chemical analysis of cell samples revealed significant concentrations of silicon in the samples that are regarded as primary cause for increased degradation. These findings could partially explain the wide spread of degradation rates reported for solid-oxide steam electrolysis experiments.

Waste recovery is an important aspect towards human and environmental health protection. Unfortunately, proper food waste management is among the serious challenges in the field of solid waste management worldwide. Therefore, it is of great importance to conduct studies towards achieving efficient and cost-effective approaches for food waste management. This study investigated the potential of recovering food waste through maggots’ production as animal feed. The influence of fly attractant application on maggot production was also investigated. The study also investigated the potential of maggot production for waste recovery and reduction. Four different types of food waste (starch food leftovers, rotten bananas and peels, rotten pineapple and peels, and rotten oranges) were used in the investigation process. From the results, it was observed that the application of fly attractants had a significant effect on the production of maggots as determined by the weights after harvesting. Average weight of 94 g/kg of maggot was achieved from banana materials with an application of fly attractant during the 8th day of the cultivation; which is equivalent to a 32.4% increase from the same day when the material was cultured without applying fly attractant. Also, from the starch materials, about 77 g/kg of maggot weight was achieved; which is a 54.6% increase from the same day and the same material but without application of fly attractant. Moreover, the relative dry weight reduction in the trials varied from 52.5% to 82.4%.

A solid structure, such as a road, building wall or envelop, used as a solar collector is considered an effective and new way to use renewable energy. This paper focused on the temperature characteristics of four structures exposed to sunshine: asphalt, red brick, composite cement and concrete road slab. Furthermore, the collected heat based on a hydraulic system was investigated experimentally. For the four structure slabs, their temperature differences are due to solar radiation absorption varied greatly by the material’s heat absorptance and color. Through the test, asphalt slab attained the highest temperature and had the weakest reflection among the structures. Compared with the others, the temperature of the asphalt slab was greater by 8.1%, 14.9% and 16.4% than the brick, composite cement and concrete, respectively. The reflection intensity growth ratio was defined and indicates the growth potential for absorbing radiation in the solid slab surface. From the experiments, it was concluded that a suitable selection of road materials can greatly improve the thermal absorption, conduction and penetration into the solid slab. The collected heat capability was approximately 250 W/m2 to 350 W/m2 in the natural summer condition. A black coating or a surface modification can collect more heat, reaching greater than 250 W/m2. The solar collecting heat efficiency with a surface configuration of the road slab can reach above 30% in the summer time.

Table grape quality is of importance for consumers and thus for producers. The objective quality determination is usually destructive and very simple with the assessment of only a couple of parameters. This study proposed to evaluate the possibility of hyperspectral imaging to characterize table grapes quality through its sugar, total flavonoid and total anthocyanin contents. Different pre-treatments (WB, SNV, 1st and 2nd derivative) and different methods were tested: PLS with full spectra, then Multiple Linear Regression (MLR) were realized after selecting the optimal wavelengths thanks to the regression coefficients (-coefficients) and the Variable Importance in Projection (VIP) scores from the full spectra. All models were good showing that hyperspectral imaging is a relevant method to assess sugar content and global phenolic content. The best model was dependent on the variable. The best models were from the full spectra and with the 2nd derivative pre-treatment for TSS; from VIPs optimal wavelengths using SNV pre-treatment for Total Flavonoid and total Anthocyanin content. Thus, relevant models were proposed using the full spectra, as well as specific windows and wavelengths in order to reduce the data sets and limit the data storage to enable an industrial use.

A novel polyphenol‑coated CoFe₂O₄ system was synthesized as a magnetic adsorbent by chemical oxidative polymerization process for magnetic solid-phase extraction of lawsone. The synthesized nanoadsorbent showed a spherical morphology with diameters under 50 nm by scanning electron microscopy images. The extraction efficiency of this adsorbent was studied towards the extraction of lawsone from saline aqueous solution in dispersion mode. Major parameters including the type and volume of desorption solvent, amount of sorbent, desorption time, extraction time, extraction temperature, ionic strength and pH were optimized. Under the optimum conditions the relative standard deviation in 0.005 µg mL^-1 (inter-day n = 6; intra-day: n = 6; and adsorbent to adsorbent n = 4) were obtained as 5.2, 8.07 and 11.7%, respectively. A linear calibration curve in the range of 0.003–0.5 µg mL^-1 with R² = 0.993 was obtained. The limit of detection and limit of quantification of the method were 0.001 µg mL^-1 and 0.003 µg mL^-1, respectively. The relative recovery percentages were in range of 90-96.4% for henna leaves, henna shampoo, and henna dermal lotion real samples.

Acute myeloid leukemia (AML) is an incurable hematological malignancy. To treat the disease successfully, new therapeutic strategies are urgently needed. One of these strategies can be the use of neurokinin-1 receptor (NK-1R) antagonists (e.g., aprepitant), because the substance P (SP)/NK-1R system is involved in cancer progression, including AML. AML patients show an up-regulation of the NK-1R mRNA expression; human AML cell lines show immunoreactivity for both SP and the NK-1R (it is overexpressed: the truncated isoform is more expressed than the full-length form) and, via this receptor, SP and NK-1R antagonists (aprepitant, in a concentration-dependent manner) respectively exert a proliferative action or an antileukemic effect (apoptotic mechanisms are triggered by promoting oxidative stress via mitochondrial Ca++ overload). Aprepitant inhibits the formation of AML cell colonies and, in combination with chemotherapeutic drugs, is more effective in inducing cytotoxic effects and AML cell growth blockade. NK-1R antagonists also exert an antinociceptive effect in myeloid leukemia-induced bone pain. The antitumor effect of aprepitant is diminished when the NF-κB pathway is overactivated and the damage induced by aprepitant in cancer cells is higher than that exerted in non-cancer cells. Thus, the SP/NK-1R system is involved in AML and aprepitant is a promising antitumor strategy against this hematological malignancy. In this review, the involvement of this system in solid and non-solid tumors (in particular in AML) is up-dated and the use of aprepitant as an anti-leukemic strategy for the treatment of AML is also mentioned (a dose of aprepitant (> 20 mg/kg/day) for a period of time according to the response to treatment is suggested).

The cyclic lipopeptide produced from Bacillus pumilus strain HY1 was isolated from Korean soybean sauce. The chemical structures of the surfactin isomers were analyzed using matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF MS) and electrospray ionization tandem mass spectrometry (ESI-MS/MS). The five potential surfactin isoforms were detected with protonated masses of m/z 994.7, 1,008.7, 1022.7, 1036.7, and 1,050.7 and different structures in combination with Na+, K+, and Ca2+ ions. ESI-MS/MS analysis revealed that the isolated surfactin possessed the precise amino acid sequence LLVDLL and hydroxyl fatty acids with 12 to 16 carbons. The surfactin content during cheonggukjang fermentation increased from 0.3 to 51.2 mg/kg over 60 h of fermentation. The surfactin extraction of cheonggukjang inhibited the growth of two cancer cell lines. The growth of both MCF-7 and Caco-2 cells was strongly inhibited with 100 μg/μL surfactin. These results suggest that surfactins produced from strain HY1 have anticancer properties.

The recycling, incineration, and final disposal rate of municipal solid waste (MSW) are calculated based on the total amount of waste input to each facility in many countries. These statistic data have serious limitation in setting the national goal and policy for effective waste management because it is not considering the amount of foreign objectives in the process of each life-cycle stage. This case study is to estimate the actual rates of recycling, incineration, and final disposal by material flow analysis (MFA) after the collection of MSW in Korea. The actual rates of recycling, incineration and final disposal for MSW in 2016 were 49.9%, 32.9% and 23.1% respectively, indicating that the recycling rate was lower by 10.1%, while the incineration and final disposal rates were raised by 7.6% and 8.4% respectively, compared with the statistics for current MSW. In addition, the changed actual rates of recycling, incineration treatment, and final landfill, and variation of waste treatment charge according to treated amounts per treatment method was analyzed. This results of this study will contribute to establish national level of plan on effective waste management.

In the present study Aprepitant (APT) ternary solid dispersions (SDs) were developed and evaluated for the first time. Specifically, ternary SDs of APT with Poloxamer 188 and Soluplus^® (SOL) were prepared via melt mixing and compared to binary APT/Poloxamer 188 and APT/SOL SDs. Initially, combined thermo-gravimetric and hot-stage polarized light microscopy studies indicated that all tested compounds were thermally stable up to 280 °C, while Poloxamer 188 acted as a plasticizer to SOL by significantly reducing the temperature required to fully solubilize the API during SD preparation. Differential scanning calorimetry combined with wide angle X-ray diffraction studies showed that crystalline API was dispersed in both binary and ternary SDs, while Fourier transformation-infrared spectroscopy studies revealed no molecular interactions among the components. Scanning electron microscopy combined with EDAX element analysis showed that the API was dispersed in nano-scale within the polymer matrices, while increasing APT content led to increasing API nano-crystals within the SDs. Finally, dissolution studies showed that the prepared formulations enhanced dissolution of Aprepitant and its mechanism analysis was further studied. A mathematical model was also investigated to evaluate the drug release mechanism

Plastic flow in body-centered cubic (bcc) alloys is governed by the thermally-activated screw dislocation motion. In bcc interstitial solid solutions, solute diffusion can occur at very fast rates owing to low migration energies and solute concentrations. Under mechanical loading, solutes may move on the same or similar time scale as dislocations glide, even at low temperatures, potentially resulting in very rich co-evolution processes that may have important effects in the overall material response. It is therefore important to accurately quantify the coupling between interstitial impurities and dislocations, so that larger-scale models can correctly account for their (co)evolution. In this paper, we use electronic structure calculations to obtain the energetics of oxygen diffusion under stress and its interaction energy with screw dislocation cores in bcc tungsten. We find that oxygen atoms preferentially migrate from tetrahedral to tetrahedral sites with an energy of 0.2 eV. This energy couples only weakly to hydrostatic and deviatoric deformations, with activation volumes of less than $0.02$ and $0.2b^3$, respectively. The strongest effect is found for the inelastic interaction between O atoms and screw dislocation cores, which leads to attractive energies on the order of 1.5 eV and a structural transformation of the screw dislocation core from an `easy' to a `hard' core configuration

This study was conducted to evaluate the feasibility of applying a two-step biological treatment process, solid-state anaerobic digestion (SSAD) and black soldier fly larvae (BSFL) composting, for treating dairy cattle manure. Biogas from SSAD of dairy cattle manure, and the digestate of SSAD was fed to BSFL. In turn, BSFL can be fed to animals as a protein supplement. Adjustment of pH and 30% inoculation ratio (IR₃₀) during SSAD produced the highest theoretical methane yield, 626.1±28.7 L CH₄/kg VS_des, with an ultimate methane yield of 96.81±2.0 L CH₄/kg VS_load. For BSFL composting, the groups with a feeding rate of 75 and 100 mg/day/larvae had the highest body weight change, which was 969.6±28.4 and 984.1±177.6%, respectively. The combination process of SSAD and BSFL composting increases the incentive for dairy cattle manure treatment enabled higher waste removal efficiency, and produced more valuable products.

The practice of collecting, treating and management of solid waste prior to disposal has become a necessity in developing and modern societies. Over the years, it is known that most wastes that are disposed have a second hand value. However, the construction cost for conventional Material Recovery Facility(s) (MRFs) has been a major barrier for implementation. These technologies require considerable technical expertise, which is often not available in developing nations to successfully operate the MRFs. Covenant University; a private mission institution through her waste to wealth scheme is focused on managing and processing used materials to reusable products. These include Pet bottles, Paper wastes, Food wastes from cafeteria, plastic food packs, nylon, tin cans and others. Specific areas chosen for the Survey include the residential areas for staff and students and the two cafeterias. The waste generated was characterized based on the waste stream so as to quantify the amount of recyclable waste generated and most occurring. The survey involved the use of structured questionnaires, on-site observations and measurements. The study reveals an average amount of recyclable waste generated per day in the institution as 13.46% pet bottles, 4.03% paper, 55.56% food waste, 12.64% plastic, 9.63% nylon and 4.68% tin cans. The study established that adequate waste characterization is a requirement for effective integrated solid waste management which would boost resource recovery, reuse and recycling.

Bamboo plastic composites have become a hot research topic and a key focus of research. However, the many strong, polar, hydrophilic hydroxyl groups in bamboo flour (BF) results in poor interfacial compatibility between BF and hydrophobic polymers. Maleic anhydride-esterified (MAH-e-BF) and lactic acid-esterified bamboo flour (LA-e-BF) were prepared using an in situ solid-phase esterification method with BF as the raw material and maleic anhydride or lactic acid as the esterifying agent. Fourier transform infrared spectroscopy results confirmed that BF esterification with maleic anhydride and lactic acid was successful, with the esterification degrees of MAH-e-BF and LA-e-BF at 21.04 and 14.36%%, respectively. Esterified BF was characterized by scanning electron microscopy, contact angle testing, X-ray diffractometry, and thermogravimetric analysis. The results demonstrated that esterified BF surfaces were covered with graft polymer and the surface roughness and bonding degree of MAH-e-BF clearly larger than those of LA-e-BF. The hydrophobicity of esterified BF was significantly higher than BF and the hydrophobicity of MAH-e-BF better than LA-e-BF. The crystalline structure of esterified BF showed some damage, with MAH-e-BF exhibiting a greater decrease in crystallinity than LA-e-BF. Overall, the esterification reaction improved BF thermoplasticity, with the thermoplasticity of MAH-e-BF appearing better than LA-e-BF.

The aim of this study was to develop a novel nanostructured lipid carriers (NLCs) with hepatocytes targeting as carriers for the magnetic resonance imaging (MRI) contrast agent (i.e., magnetic nanostructured lipid carriers, MNLCs), and to evaluate the targeting ability of the MNLCs with T2-weighted MRI both in vitro and in vivo. Here, the galactose-octadecylamine (Gal-ODA) conjugates were synthesized by chemical coupling reaction between lactose acid (LA) and octadecylamine (ODA). Then the superparamagnetic iron oxide (SPIO) loaded nanostructured lipid carrier (conjugated by Gal-ODA, Gal-NLC-SPIO) was prepared by emulsification-ultrasonic method using monoglyceride as lipid materials. The Gal-NLC-SPIO with a diameter of about 50 nm could specifically internalize into LO2 (human hepatic cell line) cells. In vitro MRI results also proved the specific targeting ability of Gal-NLC-SPIO to LO2 cells. The in vivo MR imaging experiments using an orthotopic intrahepatic xenograft tumor model further validated the hepatocytes targeted effect of Gal-NLC-SPIO. The results of this study suggested that Gal-NLC-SPIO can be used as a contrast agent to aid in the diagnosis of hepatic diseases.

A series of MgAl-layered double hydroxide (MgAl-HT), the calcined form at 500^oC (MgAlO_x) and the re-hydrated one at 25^oC (MgAl-HT-RH) were synthesized. Physicochemical properties of the catalysts were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM). Surface area of the as-synthesized, calcined and re-hydrated catalysts was determined by N₂ physisorption at -196^oC. CO₂-teperature programmed desorption (CO₂-TPD) was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1-15) were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90^oC in liquid phase, or under microwave irradiation method. The mesoporous structure and basic nature of re-hydrated solid catalyst were responsible for their superior catalytic efficiency. The robust nature was determined by using the same catalyst for five times, where the product % yield was almost unchanged significantly.

Semi-solid feedstock of AZ80 magnesium alloy modified by minor rare-earth Y element (0, 0.2, 0.4, 0.8 wt.%) were fabricated by strain induces melting activated (SIMA) in the form of extrusion and partial remelting. The effect of Y addition on the microstructure evolution of extruded and isothermal treated alloy was observed by optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and quantitative analysis. The results show that the Y addition can refine the microstructure and make the β-Mg17Al12 phases agglomerating. During the subsequent isothermal treatment at 570℃, the average solid grain size, shape factor and liquid fractions increased with prolonged soaking time. Smaller spheroidal solid grains and the larger shape factor were obtained due to Y addition. The coalescence and Ostwald ripening of solid grains operated the coarsening process simultaneously. The coarsening rate constants of AZ80M1 (0.2 wt.% Y addition) of 164.22 μm3s-1 was approximately four times less than the un-modified AZ80 alloy of 689.44 μm3s-1. In contrast, the desirable semi-solid structure featured by fine, well globular solid grains and appropriate liquid fractions and shape factor was achieved in AZ80M1 alloy treated at 570℃ for 20-30 min.

Throughout this paper the effects of injuries on athletes are highlighted in different aspects. Exertional compartment syndrome is a specific injury related to athletes that is thoroughly explored in this paper through an analysis of the anatomy, symptoms, diagnosis and treatments of the syndrome. Exertional compartment syndrome is an exercise-induced muscle and nerve condition that causes pain, swelling as well as disability in the affected muscles of the lower leg. This syndrome commonly develops in young athletes involved in sports with excessive running and repetitive impact such as track and field, soccer, basketball and lacrosse. Exertional compartment syndrome is commonly misdiagnosed as other less severe injuries such as shin splints, which is symptomatic of pain along the tibia bone of the lower leg caused by overuse. The misdiagnosis of exertional compartment syndrome allows the syndrome to worsen and intensify resulting in the only effective treatment to be fasciotomy, a surgical procedure to release the pressure within the compartment of the lower leg. There is no definitive protocol developed for patients after fasciotomy is performed. Athletes experiencing similar symptoms after surgery are usually treated for their symptoms rather than the syndrome as a whole, which does not have a high degree of success. The development of a definitive protocol utilizing the techniques of manual therapy, mobility stretching and corrective strength training can improve the adverse effects of exertional compartment syndrome as well as restore functionality to the athlete. Raising awareness of this syndrome in athletics will be effective in treating the athlete early on in order to avoid severe effects and invasive procedures.

The ocean of the planet Earth, which is as thin as a cicada's wings, play a role of catalyst to the evolving of the ancient plates. The ocean and the ancient plates of the planet Earth formed a magic Whirlpool of the Cross “十” shape with double whirl arms. The central core of the Cross “十” shape Ocean-Plate Whirlpool is the Hint Black Hole (HBH) located at the Northwestern Pacific Ocean floor which is decorated with invisible geological age distribution of clam shell. The double whirl arms of ancient plates are distinguished to be left and right at Bering Strait and just formed the ring of fire of the Pacific Ocean.The Cross “十” shape Ocean-Plate Whirlpool of the planet Earth was born at the equatorial area about 66 Ma ago and is rotating anticlockwise and drifting northward by a mini footprint of spiral at s speed of as slow as a snail moves. Obviously, it would come to an end at the North Pole about 100 Ma in the future. So, the lifespan of the Cross “十” shape Ocean-Plate Whirlpool would be about 166 Ma, from birth to death on the planet Earth.What is hidden behind of the evolving of the oceans and the ancient plates is the golden law of geometrical progression of ladder pagoda of attributes evolving of them, which is “1➨2➨4➨2➨1”, including upgrading and downgrading process. It seems to hint that what is happening on the planet Earth, including the top-level species of human race, is actually unique in the Milky Way galaxy in essence.The property roles of expanding and shrinking are existing in the Cross “十” shape Ocean-Plate Whirlpool by face to face and the exchange of property roles took place tens of millions of years ago. And that situation would happen again tens of millions of years in the future. It seems a giant circle of evolving of the exchange of property roles would be drawn by the Cross “十” shape Ocean-Plate Whirlpool in her lifetime.

In recent times, the adoption of cloud computing by small and medium-sized 9 enterprises (SMEs) has become a crucial issue. These businesses face substantial difficulties in 10 accessing reliable and affordable IT infrastructure due to economic constraints and technological 11 restrictions. Hybrid cloud computing solutions which incorporate Infrastructure as a Service 12 (IaaS), Platform as a Service (PaaS), and Software as a Service (SaaS) offer a feasible approach to 13overcoming these challenges. This study proposes a systematic literature review of cloud 14 computing's impact on SME performance emphasizing cost-efficiency, reliability, and 15 competitive advantages, using the 2020 Preferred Reporting Items for Systematic Reviews and 16 Meta-Analyses (PRISMA) framework. The inclusion criteria are bounded by (1) publication date 17 between 2014 and 2024, (2) English-language publications, (3) research focused on cloud 18 computing for SMEs, and (4) studies with a clear analytical framework for evaluating SME 19 performance. Following this process, 90 eligible research studies were included. The average 20 total cost for cloud services varies significantly, with operational costs reflecting the scalability 21 of the services and the specific needs of SMEs. This analysis offers valuable guidance for SMEs 22 and stakeholders in optimizing cloud-based strategies for enhanced performance.

Recent developments in microfluidics and biomaterials have enabled the creation of organs-on-chips (OoCs), which provide a controlled and lifelike in vitro microenvironment resembling an actual organ. Organ-on-a-chip technology offers a tremendous opportunity for efficient, cost-effective, and ethical drug testing and research. However, the high throughput and large quantities of data these complex microenvironments produce make it difficult for researchers to effectively analyze the data and draw valuable conclusions. Convolutional Neural Networks (CNNs) are most aptly positioned to address many of OoC’s challenges because of their ability to interpret microscopic images and facilitate the analytical process. Despite the growing field of AI, there have been a limited number of studies summarizing the various applications of CNNs in OoCs. This review aims to provide 1) an overview of the technology involved with CNNs and OoCs 2) an insight into the state-of-the-art applications of CNNs in OoCs including device parameters, predicting and tracking cell trajectories, super-resolution image segmentation, and image classification, and 3) an overview of existing challenges and opportunities ahead for clinical translation of this technology. Various applications of CNNs have been classified by the type of task. Different CNN models such as Faster R-CNNs, fully convolutional networks (FCNs), and Mask R-CNNs are explained and highlighted. This review article can be used as a resource for a better understanding of the potential of CNNs in biomedical research and clinical applications, particularly OoCs.

Due to Motor Neurone Diseases, a large population remains disabled worldwide, negatively impacting their independence and quality of life. This typically involves a weakness in the hand and forearm muscles, making it difficult to perform fine motor tasks such as writing, buttoning a shirt, or gripping objects. This project presents a vision-enabled rehabilitation hand exoskeleton to assist disabled persons in their hand movements. The design goal was to create an accessible tool to help with a simple interface requiring no training. This prototype is built on a commercially available glove where a camera and embedded processor were integrated to help open and close the hand, using air pressure, thus grabbing an object. An accelerometer is also implemented to detect the characteristic hand gesture to release the object when desired. This passive vision-based control differs from active EMG-based designs as it does not require individualized training. Continuing the research will reduce the cost, weight, and power consumption to facilitate mass implementation.

The existence of semantic inaccuracy §2 articles by A. Einstein “On the electrodynamics of moving bodies”, illustrating the principle of the relativity of simultaneity. In a sentence “The observers co-moving with the moving rod would thus find that the two clocks do not run synchronously while the observers in the system at rest would declare them synchronous”, the preposition “not” must be moved and placed before the word “synchronous”, at the end of the sentence. The criterion for synchronism of the clocks on the rod is the time it takes for the beam to travel from clock A to clock B and back, and for observers on the rod it will be the same both when the rod is at rest and when the rod is moving. Otherwise, observers on the rod would have had at their disposal an experiment that would allow them to determine whether the rod is moving or at rest, which contradicts the first postulate of the Special Theory of Relativity. The inaccuracy is found unchanged in modern editions in English and Russian, and can become a source of difficulties when teaching the basics of the Special Theory of Relativity based on primary sources, as well as make it difficult to understand the author’s logic when studying independently. Nobel laureate R. Feynman, having expanded and modified A. Einstein's thought experiment, eliminated the inaccuracy described in the article.

The automotive industry has witnessed a significant push towards increased fuel efficiency and reduced carbon emissions. Among many factors influencing overall vehicle efficiency, aerodynamic drag is a critical consideration, accounting for a substantial portion of fuel consumption. Our investigation focused on the drag coefficients of three prominent 2023 passenger car models – the Toyota Corolla, Hyundai Elantra, and Kia Soul. Using ANSYS Fluent to perform computational fluid dynamics, we demonstrated an inverse correlation between drag force and gas mileage, underlining the significance of aerodynamic design in fuel efficiency. Notably, the Hyundai Elantra emerged as the most aerodynamically efficient of the three vehicles, followed closely by the Toyota Corolla. In contrast, the boxier-designed Kia Soul exhibited significantly higher drag coefficients and drag forces, rendering it the least efficient of the trio. These findings emphasize the importance of environmental factors in car design. Shaping aerodynamic profiles directly impacts fuel efficiency, stability, and overall performance.

The impact of scientific articles is often measured using metrics such as the Journal Impact Factor (JIF) and CiteScore, which rely on citation counts and publication volume. In this study, we aimed to identify the predictors of article impact in the leading solid organ transplantation journals from 2019 to 2020. Article impact was determined using its citation count in 2021 compared to the JIF. Statistical analysis was performed using IBM SPSS Statistics to identify significant predictors of positive impact on the JIF. A total of 2,461 articles and reviews were included, with variations observed among the top transplantation journals. Factors such as the number of authors, open access publishing, and authors from top affiliations were found to significantly influence the impact of articles. Articles discussing kidney transplantation and COVID-19 were associated with a positive impact on the JIF, while those discussing lung transplantation had a negative impact. The findings suggest that collaborative research with more authors and involvement of top institutions enhances impact. Open access publishing also correlated with increased citations and a positive impact on the JIF. Further research incorporating a broader range of journals and years would provide a more comprehensive understanding of factors influencing article impact.

Cancer patients, susceptible to severe COVID-19 outcomes, exhibit varied vaccine responses, particularly those who are receiving chemotherapy. This prospective cohort study enrolled 115 cancer patients, and data from 91 patients who received two doses of COVID-19 vaccines were analyzed. Blood was drawn at baseline, day 28, and 6 months post-second dose for neutralizing antibody analysis. The primary outcome was seroconversion rate against wild type and Omicron at day 28. Secondary outcomes included seroconversion at 6 months, factors associated with seroconversion, and safety. Of the 157 cancer patients screened, 91 were enrolled, with 45% receiving chemotherapy. Seroconversion rates at day 28 were 77% for the wild type and 62% for Omicron. Chemotherapy did not affect seroconversion (p=0.789 for wild type, p=0.597 for Omicron). Vaccine type positively correlated with seroconversion, with an adjusted ORR of 25.86 (p=0.029) for the wild type and 17.38 (p<0.001) for Omicron with the primary heterologous vaccine. Adverse events were grade 1 in 34.0% and grade 2 in 19.7% of participants. Despite lower seroconversion against Omicron, no difference was noted between chemotherapy and non-chemotherapy groups. COVID-19 vaccinations demonstrated good tolerability. This data underscores vaccine efficacy considerations in cancer patients, informing tailored strategies for this vulnerable population.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

The organic fraction of municipal solid waste (OFMSW) is a significant environmental threat, and an economic and social challenge to manage. As such, the efficient treatment of OFMSW is a significant key factor in achieving sustainable waste management. Decentralized Composting (DC) develops a new framework of waste management. The DC Analysis Model (DCAM), proposed in our previous study, provides a powerful tool for decision makers, based on the quantification of the DC project characteristics. In this paper, we focus on the qualitative analysis as a complementary tool to support decision making, in cases where quantitative analysis is unequivocal. The qualitative analysis identifies the main players in the field, the critical stakeholders and the potential conflicts between them. It also reveals the root problems and the core competencies for the project's implementation. DCAM qualitative analysis in Shefa-Amr (case study) indicates that unresolved root problems, such as the “lack of national regulation”, “clear ownership of the project” and “lack of ongoing budget” can result in an unsustainable composting system. Countering that, “the commitment of the municipality”, together with “economic viability” and securing “suitable areas for placing composters” are among the most important core competencies for the effective implementation of DC projects.

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

In this study, robust composite solid electrolytes were developed and employed them to enhance the performance of Li-metal batteries significantly. The robust composite solid electrolytes are composed of a soft polymer, poly(ethylene oxide), a Li salt, bis(trifluoromethanesulfonyl)imide (LiTFSI), and super ionic conductive ceramic fillers such as Li1.5Al0.5Ti1.5(PO4)3 (LATP), and Li6.4La3Zr1.4Ta0.6O12 (LLZTO). The main goal of this study is to enhance the electrochemical stability and ionic conductivity. The ionic conductivities of the composite solid electrolytes were found to be 2.08 × 10-4 and 1.64 × 10-4 S cm-1 with the introduction of LATP and LLZTO fillers, respectively. The results prove that the fabricated solid electrolyte was electrochemical stable at voltage exceeding 4.25 V vs. Li/Li+. The internal resistance of the solid electrolyte significantly reduced as compare to gel electrolyte. This reduction can be attributed owing to the alleviation of bulk electrolyte, charge-transfer, and interfacial electrolyte/electrode impedance. When LiFePO4 cathode sheets are coated with a composite solid electrolyte containing LATP powders, the resulting Li-metal battery displays high capacity at 5 C (with a capacity retention of 65.2% compared to the original capacity at 0.2 C) as well as superior cyclic stability and excellent Coulombic efficiency (&gt; 99.5%, over 200 cycles). These results confirm that the composite solid electrolyte acts as a protective layer which have ability to prevent the growth of Li dendrites. Consequently, the fabricated electrolyte configuration can be engineered to enable high energy/power density and electrochemical stable cyclability in Li-metal batteries.

Bifidobacterium is the most beneficial flora of the human gastrointestinal tract, but there is a concentration threshold for Bifidobacterium to exert its beneficial properties. In this work, the effect of several simple culture methods on the number of viable bifidobacteria was discussed to improve its viable concentrations, and we unexpectedly discovered that bifidobacteria have inert growth. The concentration of viable bacteria of two isolated Bifidobacterium animalis subsp. lactis, BZ11 and BZ25 and Lactobacillus plantarum SQ-4 were investigated using solid-liquid-liquid circulation subculture, solid-liquid-liquid subculture and solid-liquid-liquid circulation subculture. These 3 subculture methods increase the viable cell concentration, and the best is the solid-liquid-liquid subculture. The highest concentrations of third-generation BZ11 and BZ25 were 9.62 × 109 CFU/mL and 1.21 × 1010 CFU/mL in order by solid-liquid-liquid subculture method, which was 10.38 times and 42.31 times higher (P<0.05) than those of the first generation, respectively. However, none of these three subculture methods increased the concentration of SQ-4. These results suggested that Bifidobacterium has growth inertia and Solid-liquid-liquid passage culture inhibiting the growth inertia. This finding is valuable in promoting the industrial application of probiotic bifidobacteria to potential probiotic food production.