Integrated photovoltaic-fuel cell (IPVFC) systems, amongst other integrated energy generation methodologies are renewable and clean energy technologies that have received diverse research and development attentions over the last few decades due to their potential applications in a hydrogen economy. This article systematically updates the state-of-the-art of IPVFC systems and provides critical insights into the research and development gaps needed to be filled/addressed to advance these systems towards full commercialisation. The design methodologies, renewable energy-based microgrid and off-grid applications, energy management strategies, optimisations and the prospects as self-sustaining power source were covered. IPVFC systems could play an important role in the upcoming hydrogen economy since they depend on solar hydrogen which has almost zero emissions during operation. Highlighted herein are the progresses as well as the technical challenges requiring research efforts to solve to realise numerous potential applications of IPVFC systems such as in unmanned aerial vehicles, hybrid electric vehicles, agricultural applications, telecommunications, desalination, synthesis of ammonia, boats, buildings, and distributed microgrid applications.

Hydroxyapatite (HAP) is the main mineral component of bones and teeth. It is widely used in medicine as a bone filler and coating for implants to promote new bone growth. Ion substitutions into the HAP structure highly affect its properties. One of the important substituents is manganese. This paper presents the new results obtained by high-precision density functional theory calculations using hybrid functionals, for studies of the Mn/Ca substitutions in HAP in a wide manganese concentration range within 2x2x2 supercell model. The experimental data on the mechanochemical synthesis of HAP-Mn samples with different Mn concentrations are also presented. The comparison between experiment and theory showed good agreement: the HAP-Mg unit cell parameters and volume decrease with increasing degree of Mn/Ca substitution. It is shown that electronic energy levels appear inside the band gap Eg of HAP, which depend on the concentration of Mn and change the photo-excitation energy of HAP, making its effective value Eg* less than the band gap Eg, and generally changing the photoelectronic properties of HAP. It was established that the energies of formation of the substitutions Mn/Ca depend on the position of the Ca atom (Ca1 or Ca2) and on the concentration of manganese. It has been shown that the replacement of calcium cations with manganese occurs predominantly at the Ca2 position.

Ninety percent of the existing building stock in Europe was built before 1990. These buildings are in urgent need for a significant improvement of energy-efficiency through renovation. Regrettably, so far only five percent of renovation projects have been able to yield energy-saving at deep renovation level. State-of-the-art renovation solutions are available, but costly and lengthy renovation processes and incomprehensible technical complexities hinder the achievement of a wide impact at a European scale. This paper presents research on Plug-and-Play (PnP) technologies supported by Building Information Modelling (BIM) to provide affordable, interchangeable and quick-installation solutions to overcome the main barriers of building deep renovation.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

Law of conservation of energy is the most well-established law of modern physics. But, inflationary cosmological model which assumes the universe to be created from a point of singularity has not been able to identify the source of energy for creation of this universe. As per uncertainty principle, a quantum vacuum fluctuation can at most create energy of ~10^-8 kg in a Planck time of ~5.4 ×10^-44 s whereas total positive energy due to matter/vacuum existing in the universe is more than ~10⁵⁴ kg. To solve this problem, we have recently published a new cosmological model (Biswaranjan Dikshit, Canadian Journal of Physics, 100, 218-225, [2022]) in which we have mathematically proved that the total energy of the universe can be zero right from the beginning of the universe to till date due to negative gravitational potential energy and thus law of conservation of energy can be satisfied during creation of the universe from nothing. In this article, starting from a simple argument, we explain why net energy of the universe can be zero only in our model, not in standard cosmological model. An interesting fact pointed out in this paper is that the factor ~10⁶² by which radius of universe has increased from its starting value of ~10^-36 m to present value of ~10²⁶ m is same as the factor by which positive energy has increased from Planck energy ~10^-8 kg to present value ~10⁵⁴ kg. This is in agreement with our new model that predicts the positive energy of universe to be proportional to the radius of universe. We also bring out to the notice that zero energy universe is possible only if smallest possible length in nature is, l_min=l_p(π/2)^1/2 = 2.0×10^-35 m. Minimum possible length is important in theory of quantum gravity and string theory.

Only now, four decades after passive houses were designed in the US and built in Canada, the authors are able to discuss the next generation of new and retrofitted buildings in the same way. This paper presents a universal system for different types of buildings and climates that includes construction experience and is reinforcing multi-disciplinary synergies. A next generation of technology uses adaptable indoor climate, integrates HVAC and building structure; applies field monitoring of energy and indoor environment and develops a performance model that is based on artificial neutral network. This approach, includes: 1. The self-learning ANN as a part of the building management system, 2. This management system guides energy optimization in a post-construction stage 3. A two-stage construction process for new and retrofits. The first stage prescribes investment level and optimizes performance; opposite in the second stage. This paper highlights that some elements of the proposed methodology have already been applied in the practice. It also underlines that this integrated multi-disciplinary system can be applied with a different combination of technological elements.

Welcome to the world of bioethanol revolution, in response to the soaring global energy demand, the production of bioethanol has taken center stage, captivating the attention of governments, academia, and the private sector alike. Over the years, research in this field has witnessed exponential growth, paving the way for sustainable energy production. Ethanol, the front-runner in renewable energy, can be derived from a plethora of sources. In this abstract, we will explore the exciting advancements and emerging trends in the production of bioethanol, shedding light on the promising future of sustainable energy. Bioethanol production presents a cost-effective solution by utilizing the abundance of agricultural resources. These resources serve as the foundation for producing bioethanol from various biomass sources. In this context, we evaluate the raw materials used, including sucrose-based, starchy-based, and perennial grasses. By exploring these options, we can gain a comprehensive understanding of the diverse range of agricultural feedstocks that contribute to the production of bioethanol, this paper delves into the multiple processes involved in the production of bioethanol from agricultural base biomass, unveiling a range of possibilities for harnessing renewable energy. The key steps that were thoroughly examined include pretreatment, which encompasses both physical and chemical methods, hydrolysis, direct fermentation, and saccharification. These steps serve as crucial components in the overall bioethanol production process from agricultural base biomass. By understanding and optimizing each of these stages, we can unlock the full potential of sustainable energy generation. The paper goes beyond exploring the production processes and delves into the different generations of bioethanol, each with its unique components. Additionally, it provides a comprehensive overview of the composition of agricultural and forest residues, shedding light on their potential as valuable resources for bioethanol production. Moreover, it highlights the significance of the agricultural sector in Nigeria's economy, emphasizing the importance of energy for enhancing productivity and efficiency. The integration of bioethanol as an energy source has the potential to propel this sector forward, fostering sustainable development and contributing to the overall growth of the Nigerian economy. By harnessing the power of bioethanol, Nigeria can tap into its energy potential, promoting energy utilization and creating a positive impact on various industries.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

Maxwell's energy-momentum tensor cannot be used as is in Einstein's equation for general relativity in the presence of sources. In this case, its four-divergence is non-zero, whereas the tensors in the equation must have this characteristic. However, the sun emits streams of ionized particles, gases are present within galaxies, material transfers in the form of ionized plasma can occur in binary star systems, and so on. These charges cannot be neglected in the study of space-time in these regions. Here, we present a modified version of this tensor that eliminates this flaw, provided that the potentials satisfy the Lorenz gauge. The distribution of sources will also be analyzed in light of fluid mechanics, allowing us to account for its influence in terms of generated pressure.

Underwater wireless sensor networks (UWSN) have recently been proposed as a way to monitor and explore the water depths' environments. Efficiently delivering the data is still a challenging problem in these networks because of the weaknesses in the acoustic transmission. To tackle such a problem, we propose a novel algorithm provides controlling mechanisms for critical long-term data forwarding underwater sensor networks, called Hop by Hop Power-Efficient Routing Protocol (Hⁿ-PERP). The proposed Hⁿ-PERP is a centralized full-control model that enhances the network's throughput and energy efficiency by a set of solutions depend on power monitoring in UWSN nodes. In particular, the model provides a guaranteed mechanism for scheduling and processing data transmission based on number of nodes, hops between the nodes, energy level and congestion within each node to minimize energy levels or power consumption by avoiding disconnected probability for any node, which in turn maximizing the network lifetime. Simulation results show that our proposed model is consistent with energy level and congestion, and is more accurate for enabling routing and data transmission. Therefore, the data packet delivery ratio and overall throughput also achieves robust scenarios of very sparse or/and weak networks, to keep on Performance stability in UWSN via adjusting hop-by-hop delay and energy consumption during packages delivery.

The growing interest in environmental sustainability issues and, at the same time, the advantages offered by blockchain technology have strong connections between these two topics. This study explores the application of blockchain technology across various environmental domains, such as air quality, climate change impacts, and resource management. The research utilised a dual approach, combining a bibliometric analysis with VOSviewer and a topic analysis using BERT models to assess the discourse within both scientific literature extracted from Scopus and practical blockchain projects obtained from GitHub. The findings reveal that food security, energy, and sustainable agriculture are predominant topics in academic discussions, with a noticeable increase in focus from 2017 onwards. Practical projects are focused on transparent tracking and decentralised management. The overlap between academic and practical spheres is evident in the shared focus on energy and environmental management, demonstrating blockchain’s growing role in addressing global environmental challenges. The study underscores the importance of integrating theoretical research with practical implementations to harness blockchain’s full potential in promoting sustainable environmental practices.

This paper generalizes the actuator disc theory to the application of crosswind kite power systems. For simplicity, it is assumed that the kite sweeps an annulus in the air, perpendicular to the wind direction (i.e. straight downwind configuration with tether parallel to the wind). It is further assumed that the wind flow has a uniform distribution. Expressions for power harvested by the kite is obtained, where the effect of the kite on slowing down the wind (i.e. the induction factor) is taken into account. It is shown that although the induction factor may be small for a crosswind kite (of the order of a few percentage points), neglecting it in calculations may result in noticeable overestimation of the amount of power harvestable by a crosswind kite system.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

A comprehensive evaluation system of rural building energy consumption from the innovative composite perspective was established, which was suitable for southwest of China. The index system was established by Brainstorming method and Delphi method, the weights of the comprehensive evaluation model were calculated by Network Process (ANP) method, the scoring criteria of all evaluation indexes were leveld based on fuzzy evaluation theory. The system model was verified by case analysis, at the countryside around Chengdu Second Circle. With the highest weight, lowest comprehensive score, and broadest range of comprehensive scores taken into consideration, three key factors affecting the target layer, namely "Percentage of Clean Energy Use", "Thermal Performance of Exterior Walls", and "Implementation Rate of Energy saving Measures". The distribution of comprehensive indicators and evaluation factors has certain spatial distribution characteristics, and the overall spatial distribution shows a characteristic of "high in the southeast and low in the northwest". Finally, Based on key factors and regional distribution characteristics, energy-saving measures have been proposed from three aspects: increasing sunrooms, adding wall insulation layers, and standardizing air conditioning temperature settings.

A comprehensive evaluation system of rural building energy consumption from a innovative composite perspective is established, which is suitable for southwest China. the brainstorming method and Delphi method were used to establish the indicator system, the ANP method was applied to calculate the weights of the comprehensive evaluation model, the scoring criteria of all evaluation indexes are constructed based on fuzzy evaluation theory, the applicability of the model is verified by an example of the countryside around Chengdu. The results showed that the score of some factors is low, whole or part area, just like the percentage of clean energy use(C24), the thermal performance of external walls(E21), the implementation of energy-saving measures(S22), were key factors affecting the target level, which has greater potential for improvement. The distribution of comprehensive indicators and evaluation factors have certain spatial distribution characteristics, the overall spatial distribution shows the characterwastic of "high in the southeast and low in the northwest". The key factors and spatial distribution characteristics found can be used as an important basis for the improvement of green energy-saving promotion measures, energy-saving retrofit programmes were proposed in terms of additional solar room, energy-saving of external walls and air-conditioning temperature setting guidance.

Evidence is growing that mankind must learn from nature, a self-sufficient and self-organized system that adopts all the opportunities to develop life and ingeniously makes the most of whatever energy source. Attempting to satisfy the requirements of our energy-consuming world, we cannot afford to disregard any available source of energy, mainly those characterized by zero-CO₂ emissions. In this context an alternative scenario could be opened by the use of the nuclear radiations emitted from naturally occurring or artificially produced radionuclides. Abandoned mines of U, Th and Rare Earths , as well as storage areas of artificially produced isotopes all over the globe are available and affordable sources of radiations that can be converted in electrical power. The transition from laboratory-scale nuclear batteries to large-area converting modules would allow to safely re-use a big amount of already existing radionuclides, converting a trouble into a resource.

The paper addresses the ongoing and continuous interest in photovoltaic energy systems (PESs). In this context, the study focuses on an isolated photovoltaic system with hybrid bat-tery-supercapacitor storage (HBSS). The integration of supercapacitors (SCs) in this system is of particular importance because of their high specific power density. In photovoltaic (PV) systems, multi-storage systems use two or more energy storage technologies to enhance system perfor-mance and flexibility. When batteries and supercapacitors are combined in a PV system, their benefits are maximized and offer a more reliable, efficient, and cost-effective energy storage op-tion. In addition, effective multi-storage power management in a PV system needs a solid grasp of the energy storage technologies, load power demand profiles, and the whole system architecture. In this work, battery-supercapacitor storage system (HBSS) is established by combining batteries and supercapacitors. The primary objective is to devise a novel management algorithm that ef-fectively controls the different power sources. The algorithm's purpose is to regulate the charge and discharge cycles of the HBSS, ensuring that the state of charge (SOC) of both batteries and supercapacitors remains within the desired range. The proposed management algorithm is de-signed to be simple, efficient, and light on computational resources. It efficiently handles the energy flow within the HBSS, optimizing the usage of both batteries and supercapacitors based on real-time conditions and energy demands. By maintaining the SOC of these energy storage components within the specified limits, the proposed method ensures their longevity and max-imizes their performance. Simulation results obtained from applying the management strategy are found to be satisfactory. These results show that the proposed algorithm maintains the SOC of batteries and supercapacitors within the desired range, leading to improved energy management and enhanced system efficiency.

The accurate forecasting of solar power output is essential for ensuring the stable and efficient operation of grid-connected photovoltaic (PV) systems, especially when faced with variable weather patterns. This research focuses on the integration of Machine Learning (ML) methodologies and climatic parameters to predict solar panel energy generation, with a specific emphasis on addressing consumption-production imbalances. Leveraging a dataset sourced from the Kaggle platform, the study is conducted in the context of Estonia, aiming to optimize solar energy utilization in this geographic region. The dataset, obtained from Kaggle, encompasses comprehensive information on climatic variables, including sunlight intensity, temperature, and humidity, alongside corresponding solar panel energy output. Leveraging machine learning algorithms, including XGBoost regression and neural networks, our model aims to identify complex patterns and relationships within the datasets. By tailoring the model to Estonia's climatic nuances, we seek to enhance the accuracy of energy production forecasts and, consequently, better manage the challenges associated with consumption-production imbalances. Furthermore, the research investigates the adaptability of the proposed model to diverse climatic conditions, ensuring its applicability for similar endeavors in other geographical locations. The performance of the forecasting model will be evaluated using error metrics like mean absolute error (MAE) and root mean squared error (RMSE). This study leverages a comprehensive dataset from Kaggle and utilizes advanced machine learning techniques to generate valuable insights. These insights can inform the development of sustainable energy policies and practices, ultimately leading to a more efficient and reliable renewable energy infrastructure.

The global demand for energy has been steadily increasing due to population growth, urbanization, and industrialization. Numerous researchers worldwide are striving to create precise forecasting models for predicting energy consumption to manage supply and demand effectively. In this research, a time-series forecasting model based on multivariate multilayered long short-term memory (LSTM) is proposed for forecasting energy consumption and tested using data obtained from commercial buildings in Melbourne, Australia: the Advanced Technologies Center, Advanced Manufacturing and Design Center, and Knox Innovation, Opportunity, and Sustainability Center buildings. This research specifically identifies the best forecasting method for subtropical conditions and evaluates its performance by comparing it with the most used methods at present, including LSTM, bidirectional LSTM, and linear regression. The proposed multivariate multilayered LSTM model was assessed by comparing mean average error (MAE), root-mean-square error (RMSE), and mean absolute percentage error (MAPE) values with and without labeled time. Results indicate that the proposed model exhibits optimal performance with improved precision and accuracy. Specifically, the proposed LSTM model achieved a decrease in MAE by 30%, RMSE by 25%, and MAPE by 20% compared to the LSTM method. Moreover, it outperformed the bidirectional LSTM method with a reduction in MAE by 10%, RMSE by 20%, and MAPE by 18%. Furthermore, the proposed model surpassed linear regression with a decrease in MAE by 2%, RMSE by 7%, and MAPE by 10%. These findings highlight the significant performance increase achieved by the proposed multivariate multilayered LSTM model in energy consumption forecasting.

Wave energy converter (WEC) arrays deployed in coastal regions may create physical disturbances potentially resulting in environmental stresses. Presently, limited information is available on the nature of these physical disturbance or the resultant effects. A quantitative Spatial Environmental Assessment Tool (SEAT) for evaluating potential effects of wave energy converter (WEC) arrays on nearshore hydrodynamics and sediment transport is presented for the central Oregon coast (USA) through coupled numerical model simulations of an array of WECs. Derived climatological wave conditions were used as inputs to the model to allow for the calculation of risk metrics associated with various hydrodynamic and sediment transport variables such as maximum shear stress, bottom velocity, and change in bed elevation. The risk maps provided simple, quantitative, and spatially-resolved means of evaluating physical changes in the vicinity of a hypothetical WEC array in response to varying wave conditions. Near-field risk of sediment mobility was determined to be moderate in the lee of the densely spaced array, where the potential for increased sediment deposition could result in benthic habitat alteration. Modifications to the nearshore sediment deposition and erosion patterns were observed near headlands and topographic features, which could have implications for littoral sediment transport. The results illustrate the benefits of a risk evaluation tool for facilitating coastal resource management at early market marine renewable energy sites.

Ecological Society is based on socioeconomic systems directed to the equilibrium of inter-relationships between environment, climate, production systems, technologies and human communities to promote the overall well-being of people and the Earth planet. It has a main goal for supporting sustainable development and equitable societies and achieving optimal health outcomes recognizing the interconnection between people, technologies, animals, plants, and their shared environment for the one health. Using data of scientific publications and patents until the year 2024, this study shows new technologies that can support the energy transition with the shift from fossil fuels to renewable energy sources in an effort to reduce CO₂ emissions for an ecological society having, whenever possible, zero-carbon economies to reduce environmental pollution and climate change and foster health and wellbeing of people. Results reveal that sustainable technologies supporting the transformation of the energy sector, economies and societies, and having a rapid growth, are blue hydrogen, floating photovoltaic systems, carbon capture and utilization, green hydrogen and liquid metal batteries. These findings can guide decisions of policymakers and stakeholders towards fruitful investments driving the transition from fossil-based to zero-carbon socioeconomic systems to have a long-run sustainable development of overall world system that has to direct towards an ecological society associated with one health.

Building energy modelling tools play a crucial role in quantifying and comprehending the energy performance of buildings. These tools demand substantial amounts of data, which can be challenging to acquire and are often associated with significant uncertainties. The incorporation of Sensitivity Analysis represents a relevant step towards developing reliable models, as it identifies the most critical parameters that require a meticulous characterization. In this study, a Sensitivity Analysis based on Morris method was conducted to assess the relevance of 14 input parameters affecting thermal loads across four dwelling typologies modelled in EnergyPlus. Different number of Morris trajectories and levels were considered to analyse the impact of the user-defined values of r and p when employing Morris method. Convergence was achieved from r=200 and p=12, which are higher than the typically employed values (r=10 and p=4). Setpoint temperatures, orientation, roof solar absorptivity and roof conductance rank among the most relevant parameters affecting thermal loads, however variations are observed for the four case studies.

This paper examines the energy efficiency of three variations of the two-degree-of-freedom transverse galloping energy harvester. These variants differ in the number and placement of electromechanical transducers. By utilizing the harmonic balance method, limit cycles of mathematical models of devices were determined. Analytical expressions derived from models were then used to formulate the efficiency of the systems. It was demonstrated that efficiency depends on flow speed and can be comprehensively characterized by four criteria parameters: peak efficiency, denoting the maximum efficiency of the system, and high efficiency bandwidth, which describes the range of flow velocities within which the efficiency remains at no less than 90% of peak efficiency. The values of these parameters are heavily reliant on the speed at which the system achieves peak efficiency—referred to as the nominal speed nominal speed, which in turn is related to the critical speed of the system. Comparative analysis revealed that only the two-degree-of-freedom device equipped with two electromechanical transducers can potentially outperform a simple one-degree-of-freedom system in terms of efficiency.

The purpose of this work is to study the mechanism of running-in during the friction and to determine the informative parameters characterizing the degree of its completion. During the friction, contact interaction of rough surfaces causes various wave phenomena covering a wide range of frequencies, the subsequent frequency analysis can provide information about the sizes of wave sources and thereby clarify the mechanism of interaction between surface roughness. The using of the wavelet transform for processing of the signals of audible acoustic emission made it possible to determine the beginning and the end of the change in the frequency ranges of the interaction of roughness. The code developed by the authors was used to analyze the acoustic emission signals by using wavelet energy and entropy criteria. The mother wavelet was chosen by carefully evaluating the effectiveness of 54 preliminary candidates for the mother wavelet from 7 wavelet families, ac-cording to three criteria: 1) maximum wavelet energy; 2) Shannon entropy minimum; 3) maximum energy-to-Shannon entropy ratio.

The prevalence of overweight and obesity is increasing worldwide not only in Western countries but also in Asian countries. Among Asian countries, South Asian countries experience the rapid increase of overweight and obesity that co-exist with the rapid increase of obesity-related non communicable diseases such as diabetes, dyslipidemia and cardiovascular. The phenomena in South Asian countries are triggered by growth in population size, population aging, urbanization and changes in lifestyle including increases in energy intake and reductions in physical activity. The imbalance between energy intake and energy expenditure leads to the development of positive energy balance, which over the time acumulate in a higher body fat. South Asians were reported to have a more unfavorable body composition with a higher body fat percentage as compared to BMI-matched Caucasians. The differences in body composition between South Asians and Caucasians contribute to differences in resting energy expenditure, in which South Asians have a lower resting energy expenditure as compared to BMI-matched Caucasians. Resting energy expenditure is the largest component of daily total energy expenditure, and therefore play an important role in determining the energy balance between energy intake and expenditure.

In order to meet the national energy saving goals set in the Vietnam National Energy Efficiency Program in the period of 2019 – 2030 (VNEEP), the Vietnamese government has adopted a series solutions and policies to improve energy efficiency. The Vietnam’s 63 provinces will be as main actor for the national achievement in energy efficiency. Thus, understanding the province’s potentiality of energy efficiency is useful for the harmonious and sustainable development between the economy and energy systems. In this study, provincial and national data from General Statistic Office are analyzed in terms of the energy efficiency levels. With the trends of economic development and energy consumption in both national and regional levels, the Lorenz curve between Vietnamese energy consumption and GDP is investigated. The Lorenz coefficient shows the energy allocation is nether reasonable nor balanced. By using clustering method, the 63 provinces of Vietnam clustered into 7 groups that the provinces in the cluster has the similar indexes of energy efficiency i.e. ability, responsibility, potential and difficulty. The energy consumption and GDP are predicted in the period of 2019 – 2025. Based on the difference of GDP development and energy consumption levels, the target of energy efficiency for each province through clustering is set. The results show that 33 provinces included in the cluster 1, 2, 3, 4 and 6 are heavy contribution. Among them, the provinces in the cluster 2 and 3 need to focus on the industry sector in their energy saving policy. The cluster 7 included the under-developed provinces can learn development’s experiences of the provinces in the cluster 1, 2, 3 and 4 to find the best way of their future development.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

This paper proposes how to reduce the consumption of active electrical energy (kwh) by 90.3% while maintaining the same mechanical work speed (RPM) at variable torque loads (fans or air-fluid blowers, centrifugal pumps are not included). of water and similar fluids), by using the “Fan Law” in an innovative way in PMSM-type synchronous motors (a comparative study never before carried out on the Fan Law). The work is carried out comparatively between brushless a-synchronous motors with starting loop (or motor with a short-circuited loop) versus brushed a-synchronous motors and PMSM-type synchronous motors without the need to use VDF (variable frequency drives), simplifying technology (electronics) and saving costs in an innovative way (R+D+i). The case study was developed on a design applied to a centrifugal air extractor/blower with PMSM/IPM type synchronous motor. Applying one of the fan affinity laws –with the impeller diameter 10.5 (mm) constant- the electrical power absorbed by the blower motor is proportional to the cube of the shaft speed: . Being “P” power (Watts) and “N” speed (RPM). Carrying out a comparative study between power (watts), active energy consumption (kwh) and rotational speed (RPM). This has a direct impact on the costs of residential and commercial single-phase active electrical energy consumption, measured in kilowatt-hours (kwh). Carrying out a comparative study between three (3) types of alternating current (AC) electrical machines, according to the NEMA (National Electrical Manufacturers Association); AC motors fall into three (3) categories. One (1), synchronous motors (Syncrhonous Motor) of three types: (1a) excitation by DC (DC Excited Motor), (1b) permanent magnet (Permanent Magnet Motor) and (1c) reluctance motor (Reluctance Motor) or motor Step by Step. Two (2), asynchronous induction motors of two types: (2a) Squirrel-Cage Induction Motor and (2b) Wound-Rotor Induction Motor. Three (3) series-wound motor (Series-Wound Motor) also called universal motor (they have carbons).

Electrifying off-grid and isolated islands in the Philippines remains one of the challenges that hinders community development. One of the solutions seen to ensure energy security, expand energy access and promote a low carbon future in this isolated islands is the use of renewable energy sources. This study wishes to determine the nearshore wave energy resource during monsoon seasons in Cuyo Island using a 40-year wave hindcast and 9-year on-site wind speed data to develop high resolution wave energy model using SWAN wave model, and assessed its annual energy production through matching with wave energy devices. Results shows that average significant wave height (Hs), peak period (Tp) and wave power density (Pd) during northeast monsoon are Hs = 1.35 m, Tp = 4.79 s and Pd = 4.05 kW/m respectively, while southwest monsoon which is sheltered by the mainland resulted to a lesser outcome, Hs = 0.52 m, Tp = 3.37 s and Pd = 0.34 kW/m. While the simulated model was observed to overestimate the wave energy resource (Bias = 0.398, RMSE = 0.54 and SI = 1.34), it has a strong relationship with the observed values (average r = 0.9). Its annual energy production is highest at Station 5, with AEPWaveBouy = 43.761 MWh, AEP-Pelamis = 216.786 MWh and AEPWave Dragon = 2462.66 MWh. At present, the minimum requirement for a wave energy development to be feasible is 5 kW/m, which in this case, Cuyo Island falls short, but with the continuous evolution of wave energy converters, applications on milder re-sources will soon materialized.

We present a model of space that considers it to be a quantized dynamical entity which is a component of the universe along with matter and radiation. The theory is used together with thermodynamic data to provide a new view of cosmic evolution and an insight into the nature of dark energy and dark matter. Space is made up of energy quanta. The universe started from an atomic size volume at very high temperature and pressure near the Planck epoch. Upon expansion and cooling, phase transitions occurred resulting in the formation of radiation, fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters. From a phase diagram of cosmic composition, we obtained a correlation between dark energy and the energy of space. Using the Friedmann equations, data from WMAP studies of the composition of the universe at 3.0 x 10⁵ (a=5.25 x 10^-2) years and at present (a=1), are well fitted by our model with an equation of state parameter, w= -0.7. The accelerated expansion of the universe, starting at about 7 billion years, determined by BOSS measurements, also correlates well with the dominance of dark energy at 7.25 x 10⁹ years ( a= 0.65). The expansion can be attributed to Quintessence with a space force arising from a quantum space field. From our phase diagram, we also find a correlation suggesting that dark matter is a plasma form of matter similar to that which existed during the photon epoch immediately prior to recombination. Our Quantum Space Model leads to a universe which is homogeneous and isotropic without the need for inflation. The thermodynamics of expansion is consistent with BOSS data that show the process to be adiabatic and the rate of expansion decelerating during the first 6 billion years after the Big Bang. However, it became non-adiabatic and accelerating thereafter. This implies an influx of energy from a source outside the universe; it warrants consideration as a possible factor in the accelerated expansion of the universe.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

The global photovoltaic (PV) installed capacity, vital for the electric sector decarbonation, has reached 1,552.3 GWp in 2023. In France, the capacity stood in April 2024 at 19.9 GWp. The growth of the PV installed capacity over a year was nearly 32% worldwide and 15.7% in France. However, integrating PV electricity into grids is hindered by poor knowledge of rooftop PV systems, constituting 20% of France's installed capacity, and the lack of measurements of the production stemming from these systems. This problem of lack of measurements of the rooftop PV power production is referred to as the lack of observability. Using ground truth measurements of individual PV systems, available at an unprecedented temporal and spatial scale, we show that estimating the PV power production of an individual rooftop system by combining solar irradiance and temperature data, the characteristics of the PV system inferred from remote sensing methods and an irradiation-to-electric power conversion model provides accurate estimations of the PV power production. Our study shows that we can improve rooftop PV observability, and thus its integration into the electric grid, using little information on these systems, a simple model of the PV system and weather data.

The Covid-19 pandemic and the subsequent implementation of lockdown measures have significantly impacted global electricity consumption, necessitating accurate energy consumption forecasts for optimal energy generation and distribution during a pandemic. In this study, we propose a new forecasting model called the Multivariate Multilayered LSTM with Covid-19 case injection ($\proposedModel$) for improved energy forecast during the next occurrence of a similar pandemic. We utilize data from commercial buildings in Melbourne, Australia during the Covid-19 pandemic to predict energy consumption and evaluate the model's performance against commonly used methods such as LSTM, Bi-LSTM, Linear Regression, Support Vector Machine and the previously published work of Multilayered LSTM (M-LSTM). The proposed forecasting model was analyzed using the following metrics of mean percent absolute error (MPAE), normalized root mean square error (NRMSE), and $R^2$ score values. The model $\proposedModel$ demonstrates superior performance, achieving the lowest MPAE values of 0.061, 0.093, and 0.158 for data sets from 3 different buildings, respectively. Our results highlight the improved precision and accuracy of the model, providing valuable information for energy management and decision-making during the challenges posed by the occurrence of a pandemic like Covid-19 in the future.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

The paper proposes a methodological way to compensate the imbalance between energy generation and consumption using the battery block of electric vehicles as energy reservoir through the well-known Vehicle to Grid system (V2G). The method is based on a simulation process developed by the authors that take into consideration the daily fluctuations of energy consumption as well as the power level generated by an energy source, either conventional, renewable or hybrid. The study shows that for very large electric vehicle fleet the system renders non-viable, since the remaining energy in the battery block to let the electric vehicle usable for running during daytime avoids to compensating for the energy grid imbalance, only allowing to cover a percentage of the energy imbalance, which the proposed methodology may optimize. The analysis of the proposed methodology also shows the viability of the system when being applied to a small fleet of electric vehicles, not only compensating for the energy imbalance but also preserving the required energy in the battery of the electric vehicle to make it run. The method allows predicting the optimum size of electric vehicle battery, which depends on the energy generation level, coverage factor of the energy imbalance and size of the electric vehicle fleet.

This article presents a method of segmenting images with gray levels that uses Onicescu's information energy calculated in the context of the neutrosophic theory. Starting from the information energy calculation for complete neutrosophic information, it is shown how to extend its calculation for incomplete and inconsistent neutrosophic information. The segmentation method is based on calculation of thresholds for separating the gray levels using the local maximum points of the Onicescu information energy.

Among the electrochemical energy storage (EES) technologies, rechargeable batteries (RBs) and supercapacitors (SCs) are the two most desired candidates for powering a range of electrical and electronic devices. The RB operates on Faradaic processes, whereas the underlying mechanisms of the SC vary as non-Faradaic in the electrical double layer capacitors (EDLCs), Faradaic at the surface of the electrodes in the pseudo capacitors (PCs), and a combination of both non-Faradaic and Faradaic in the hybrid capacitors. The EDLCs offer high power density but low energy density. The hybrid capacitors take advantage of the Faradaic process without compromising their capacitive nature. Unlike batteries, supercapacitors provide high power density and numerous charge-discharge cycles; however, their energy density lags that of batteries. Here, we review recently published critically selected articles on supercapatteries, a generic term that refers to EES devices that can combine the merits of EDLCs and RBs. Also discussed are the properties, design strategies, and future perspectives of supercapatteries.

With the swift advancement of wearable electronic devices and the electronic textile industry, the energy storage components of these devices must possess the capability to maintain stable mechanical and chemical properties even after undergoing multiple bending or tensile deformations. This circumstance has expedited research efforts toward novel materials, processing techniques, and designs for flexible energy storage devices. Among the myriad of materials investigated thus far, biomass-derived architectures have garnered significant attention due to renewability, cost-effectiveness, and abundance in earthly resources. Notably, flexible carbon membrane/ monolithic derived from biomass serve as a particularly promising option for self-supporting electrodes, align seamlessly with the requirements of next-generation electronic devices, and obviate the need for additional costs, unnecessary weight, and the high contact resistance that additive insulating adhesives may entail. This review delves into the comprehensive analysis of biomass feedstocks and methodologies employed in the synthesis of flexible self-supporting carbon electrodes. Subsequently, the advancements in their application in energy storage devices are elucidated. Finally, an outlook on the potential of biomass self-supported carbon architectures and the challenges they face is provided.

The shortage of precooling equipment in litchi producing regions could lead to a high loss rate, poor quality of litchis. It is urgent to develop a portable precooling device for litchi producing regions. In this study, a novel spray hydrocooler with thermal energy storage (TES) were designed, fabricated, and tested. A simple mathematical model of TES capacity, ice coil thermal resistance and refrigeration system was employed to determine hydrocooler parameters. Then designed the structure of the spray hydrocooler. Maximum charging test was implemented with full TES capacity and litchi spray hydrocooling experiments were carried out at different charging times, spray flow rate, and litchi load with one-third TES capacity. Results showed that: (1) the spray hydrocooler allows for the rapid and effective precooling of litchis; (2) the hydrocooler can precool 299 kg litchis with one-third TES storage, meet the precooling requirements; (3) the effective TES capacity achieved 1.25×108 J at the maximum TES capacity of the hydrocooler, while the energy efficiency ratio (EER) is 2; (4) the precooling capacity was maximum and the average power consumption was minimum when the litchi load was 23 kg and the spray flow rate was 30 L min-1. Longer charging time is the most important factor in increasing precooling capacity and reducing average power consumption.

Large inconsistencies in the outcome of precise measurements of Newtonian gravitational ‘constant’ were identified throughout more than three hundred experiments conducted up to date. This paper illustrates the dependency of the Newtonian gravitational parameter on the curvature of the background and the associated field strength of vacuum energy. Additionally, the derived interaction field equations show that boundary interactions and spin-spin correlations of vacuum and conventional energy densities contribute to the emergence of mass. Experimental conditions are recommended to achieve consistent outcomes of the parameter precision measurements, which can directly falsify or provide confirmations to the presented field equations.

Most European cities are characterized by very large areas, often formed by buildings with low quality, from a series of point of view. The possibility of renovating them is strategic to improve both the quality of life and to the possibility of economic recovery for building companies. In the last decades, the attention of the scientific community has been addressed to the energy renovation, thanks to the strong activities of the European Community in this field. However, since a relevant part of the EC territory is at risk of earthquake, the possibility to combine both energy and seismic renovation actions may be strategic for many countries. In particular, Italy and Romania are linked by a common social tradition that springs from the Roman Empire. Nowadays, this link is stronger, thanks to common interests in social, cultural and business fields. Therefore, the investigation of possible synergies for seismic and energy renovation strategies may be really interesting for both countries. This paper represents the first step in this direction. After an overview of regulations and common practices for buildings with reinforced concrete structures, in both states, some key combined renovation interventions will be described and discussed, as well as advantages and perspectives of integrated renovation approaches.

Daylighting design is not only a stage of dimensioning glazed surfaces to provide sufficient natural light to an occupied space, but also a method of analysing how this matter can be achieved without unwanted effects, such as: gains and losses of heat, glare, and variations of the daylighting intensity, at various indoor distances and levels. According to the international regulations in force, glazed surfaces must be designed with a careful balance between the admission of natural light and thermal performance, such as heat loss in winter and heat gain in summer. In a novel project, it is essential to determine the optimal ratio of window-to-wall surface area. This necessity arises because the materials constituting the glazed surfaces of windows typically exhibit lower insulation properties compared to those of the building's walls. This methodology could be applied to building renovations when envelope modifications are possible and suitable. The case study presented in the paper highlights the energy consumed due to a group of windows with a large glazed area in an existing building, located in a temperate continental climate area. The energy consumption results from supplementary artificial lighting required to maintain adequate illumination for indoor activities and that to counterbalance heat loss during colder periods are evaluated. The analysis performed by modifying the glazed surface led to the identification of an optimum value of windows dimensions for an energy consumed minimum.

One of the future challenges of increasing the harnessed solar power is efficiency using of CubeSat sides. One of the approaches is using integrated antenna systems with solar panels or payloads. This study proposes a new approach to the use of integrated antenna systems in remote sensing missions. In this approach, due to the integration of antenna system with payload (in our case, with camera), it is possible to achieve a significant increase in the power generation. Calculations are carried out for cases when the antenna system are integrated with the optical system (α = 0°), which implies that they use one plane, in the second case they are spaced at an angle of α = 90° and in the third case when they are directed to opposite sides (α =180°). In the case of α = 0°, where the camera and antenna module are aligned co-axially, there is no energy expenditure for CubeSat orientation. However, in the other two cases, energy is required for rotation and maintenance of the specified orientation throughout the entire duration of the satellite's flight over the ground station, amounting to 111.99 mW when α = 90° and 44.33 mW when α = 180°.

In electric circuits, energy is delivered by electromagnetic fields through the space, as suggested by Kraus and Carver. They provide insights by showing electric/magnetic fields and Poynting vector directions around a DC circuit. In this work, the energy flow mechanism by Kraus and Carver is further studied theoretically for arbitrary terminal potentials of a DC power source.

The public interest towards renewable and clean energy is an important part of shaping consumer behavior and policy towards these topics. A “big data” approach towards assessing the public interest for various topics consists in using freely available search frequency data for the Google search engine, through the Google Trends service. The search data frequency can be used to assess public opinion for a variety of topics, such as medicine, climate change and environmental concerns, finance, and economics etc. A study of the public interest towards wind energy topics is reported here. Six Google search keywords (“Wind power”, “Wind energy”, “Offshore wind”, “Wind farm”, “Wind turbine” and “Wind generator”) were investigated in the 2004–2020-time range. All keywords except “Offshore wind” show a steady decrease from a 2008 – 2010 maximum up to 2015, followed by a period limited change in the 2015 – 2020 range. The interest towards offshore wind topics follows a similar trend but increases in frequency starting from 2015 and reaches a maximum in 2018. Overall, the Google Trends data show a decrease of public interests towards most wind energy topics, with the exception of “Offshore wind”, for English speaking users, in the 2004–2020-time range.

The article is devoted to a bibliometric analysis of scientific publications reflecting trends in scientific publications related to the energy transition of leading universities in Saudi Arabia. The universities were selected based on the presence of joint publications with the Saudi Arabian Oil Company, they are: King Fahd University of Petroleum and Minerals, King Abdullah University of Science and Technology, and King Saud University. The importance of studying the experience of Saudi Arabia for Russia in the context of the energy transition was highlighted. The analysis was based on Scopus platform data related to Subject Areas: Physical Sciences. Scientists from Saudi Arabian universities are increasingly publishing with co-authors from China, India, Egypt, Pakistan, and Malaysia, while maintaining high interaction with co-authors from the United States, South Korea, and the United Kingdom. Authors from the Russian Federation publish poorly with co-authors from Saudi Arabia. The trends in the topics of scientific publications were investigated, and their connection with the renewable energy topic was shown. The VOSviewer software was used to determine the main research areas using the cluster analysis method based on the co-occurrence of key terms. The analysis was done for both Author's keywords and Index keywords of the Scopus system. Graphical representation of the final choice of terms to describe research trends was proposed. TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

We present a new method for assessing the strength of fuzzy rules with respect to a dataset, based on the measures of the greatest energy and smallest entropy of a fuzzy relation. Considering a fuzzy automaton (relation) in which A is the input fuzzy set and B the output fuzzy set, the fuzzy relation R1 with greatest energy provides information about the greatest strength of the input-output and the fuzzy relation R2 with the smallest entropy provides information about uncertainty of the relationship input-output. We consider a new index of the fuzziness of the input-output based over R1 and R2. In our method this index is calculated for each pair of input and output fuzzy sets in a fuzzy rule. A threshold value is set for choosing the most relevant fuzzy rules with respect to the data.

Considering that traditional energy sources such as fossil fuel are about to deplete during the following decades, governments try to turn to renewable energy. It is commonly known that Greece has a natural advantage of abundant solar energy and wind power due to its geographical location and characteristics.The main focus of this study is to examine how wind energy potential across the Aegean Sea and continental Greece can provide a promising field for investments in Greece, considering the economic crisis, current trends and future perspectives.We firstly focus on current legislation framework considering that laws associated with such types of investment in Greece are very complex and rapidly changing. Furthermore, a case study for a hypothetical investment plan concerning a wind park located in an Aegean island will be presented. RetScreen which is a software made by the Canadian government, will be used as a decision support tool for analyzing the potential investment scenario and a financial report will follow with estimation of the overall cost, depreciation, upcoming benefits, and payback period of the investment.Data analysis concludes that wind parks still prove to be an economically viable investment, although incentives considering the guaranteed price per kwh and faster investment times must be provided by the government.

It is proven that the Clapeyron-Mendeleev equation, originally discovered for gases with large entropy, describes the state of dark matter and energy due to enormous self-gravitation. It is shown that the dark matter exists as compact cold neutrino stars at positive temperature with size twice the Schwarzschild radius. In contrast, the dark energy is dark matter at temperature below the absolute zero, which is locked entirely in black holes, where the pressure is negative as required for the Universe intrinsic expansion. The derived dark phase diagram predicts negative critical temperatures for the Big Bang and the Big Rip of black holes.

La minería es una industria intensiva en energía que requiere una fuente estable de electricidad. Con el aumento de la demanda de minerales y la disminución de las leyes, se espera que la demanda de energía aumente en un 36% para el 2035. Este aumento de la demanda depende del uso de combustibles fósiles ya que la electricidad producida y comprada en las empresas mineras se basan principalmente en el caso de los combustibles fósiles, los costos de los sistemas de almacenamiento de energía solar y eólica han caído a una escala sin precedentes, lo que alienta a las empresas mineras a probar estas tecnologías.Entre los factores que influyen en el uso de energía renovable, se encuentra el beneficio a la comunidad en la etapa de operación y cierre o post-cierre de un proyecto minero, el siguiente factor es el perfil de consumo eléctrico o demanda es importante para el cálculo de su almacenamiento o no, de las energías renovables a utilizar. Como tercer factor está el cálculo del consumo en los procesos. Los rangos de penetración determinarán si es posible su almacenamiento de energía, y si es posible utilizar control híbrido (solar - eólico), para ello es importante el uso de herramientas digitales como el programa Holmer, es una herramienta importante que técnica y económica.El gobierno debe tener una perspectiva que ayude en los temas regulatorios necesarios para impulsar proyectos de energía renovable con diferentes incentivos e intereses según el contexto minero.

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

The relative proportions between nutrients affects the fate of them for metabolic interconversion, storage and turnover or, essentially for energy, in a process of partition modulated by hormonal and metabolic factors. A basic common chow model was used: ST or standard diet, HF high-fat and HP or high-protein had a common substrate. A CF cafeteria-type diet was added for comparison. Rats (female and male) received the diet for 30d. Nutrient intake and body composition were measured. Plasma glucose, lactate, testosterone (T) and estradiol (E2) were measured. Common groups energy intake, was largely based in carbohydrates CH, yielding 6C units, which were fully oxidized or stored as 2C fragments (fatty acids). Lactate (3C) was partially stored as glycerol of TAG. Accrual of 2C far exceeded about ten-fold that of 3C. Amino acid (AA) catabolism yielded 2C, 3C and 4C-5C fragments, the latter acting as Krebs cycle anaplerotic intermediates (KCAI), that facilitated the oxidation of 2C in detriment of TAG accumulation Lactate levels, were related to lactic dehydrogenase activities in muscle and liver. TAG accrual was maximal in CF, quite differently from HF with similar diet lipid proportion. Maximal rates of lipid storage were found in ST (and CF) groups. Females showed a higher ability to oxidize CH and to store less TAG. T increased N and protein deposition, whilst E2 decreased them favoring AA oxidation and the availability of KCAI. In the rat, an effective energy partition scheme requires that about half of the energy is provided by CH (polysaccharide), and needs enough protein to provide KCAI for a smooth 2C oxidation.

The recent provision of energy-harvesting capabilities to wireless sensor networks has entailed the redefinition of design objectives. Specifically, the traditional goal of maximizing network lifetime has been replaced by optimizing network performance, namely delay and throughput. The present paper contributes to this reformulation by considering the routing problem for the class of time-driven energy-harvesting WSN (EH-WSN) under regular or quasi-periodic energy sources. In particular, this paper shows that the minimum hop count (MHC) criterion maximizes the average duty cycle that can be sustained by nodes in this type of scenarios. This is a primary objective in EH-WSN, since large duty cycles lead to enhanced performance. Based on a previous result, a general expression is first obtained which gives mathematical form to the relationship between duty cycle and traffic load for any node in a time-driven EH-WSN fed by a regular energy source. This expression reveals that the duty cycle achievable by a node decreases as its traffic load increases. Then, it is shown that MHC minimizes the average traffic load over the network, and thus it maximizes the average duty cycle of nodes. This result is numerically validated via simulation by comparison with other well-known routing strategies. Accordingly, this paper suggests assigning top priority to the MHC criterion in the development of routing protocols for time-driven EH-WSN under regular energy sources.

The main objective of this article was to evaluate the repercussions of the crises resulting from the COVID-19 pandemic and the war in Ukraine on changes in the European Union's reliance on energy raw material imports, particularly from Russia. Furthermore, several specific objectives were outlined: to ascertain the EU's energy balance and any alterations therein, to identify changes in the concentration of energy raw material imports among EU countries during the crises, to determine the level and fluctuations in energy raw material import dependence within the EU and individual member states throughout the crises, and lastly, to assess changes in the concentration of energy raw material imports from Russia in EU countries during the crises. The research encompassed all 27 EU Member States as of 31st December 2022, and the examination period spanned from 2010 to 2022. The information sources included relevant literature on the subject and data sourced from Eurostat. In conducting the analysis and presenting the data, several methodologies were employed, including descriptive, tabular, and graphical techniques. Additionally, quantitative measures such as the Gini structure concentration coefficient and concentration analysis through the Lorenz curve were utilized. During the COVID-19 pandemic, the EU experienced a slight reduction in dependence on energy raw material imports. However, this reduction was short-lived and mainly attributed to the decrease in energy demand caused by the pandemic. Conversely, the war in Ukraine had a substantial impact, leading to a notable surge in energy raw material imports as a result of stockpiling efforts and the need to safeguard against further disruptions in the energy market. Notably, the EU's reliance on energy imports from Russia was already considerable. Following the outbreak of the conflict in Ukraine, imports of oil, petroleum products, and solid fossil fuels experienced significant decline due to imposed sanctions. Nonetheless, restrictions on natural gas imports were comparatively less severe.

In Electrified Vehicles, the cost, efficiency, and durability of electrified vehicles are dependent on the energy storage system (ESS) components, configuration and its performance. This paper, pursuing a minimal size tactic, describes a methodology for quantitatively and qualitatively investigating the impacts of a full bandwidth load on the ESS in the HEV. However, the methodology can be extended to other electrified vehicles. The full bandwidth load, up to the operating frequency of the electric motor drive (20 kHz), is empirically measured which includes a frequency range beyond the usually covered frequency range by published standard drive cycles (up to 0.5 Hz). The higher frequency band is shown to be more efficiently covered by a Hybrid Energy Storage System (HESS) which in this paper is defined as combination of a high energy density battery, an Ultra-Capacitor (UC), an electrolytic capacitor, and a film capacitor. In this paper, the harmonic and dc currents and voltages are measured through two precision methods and then the results are used to discuss about overall HEV efficiency and durability. More importantly, the impact of the addition of high-band energy storage devices in reduction of power loss during transient events is disclosed through precision measurement based methodology.

A comprehensive review of uncertainties in power systems, covering modeling, impact, and mitigation, is essential to understand and manage the challenges faced by the electric grid. Uncertainties in power systems can arise from various sources and can have significant implications for grid reliability, stability, and economic efficiency. Australia, susceptible to extreme weather such as wildfires and heavy rainfall, faces vulnerabilities in its power network assets. The decentralized distribution of population centers poses economic challenges in supplying power to remote areas, a crucial consideration for emerging technologies emphasized in this paper. In addition, the evolution of modern power grids, facilitated by deploying the advanced metering infrastructure (AMI), has also brought new challenges to the system due to the risk of cyber-attacks via communication link. However, the existing literature lacks a comprehensive review and analysis of uncertainties in modern power systems, encompassing uncertainties related to weather events, cyberattacks, and asset management, as well as the advantages and limitations of various mitigation approaches. To fill this void, this review covers a broad spectrum of uncertainties considering their impacts on the power system and explores conventional robust control, and modern probabilistic and data-driven approaches for modelling and correlating the uncertainty events to the state of the grid for optimal decision making. This article also investigates the development of robust and scenario-based operations, control technologies for microgrids (MGs) and energy storage systems (ESSs), and demand-side frequency control ancillary service (D-FCAS) and reserve provision for frequency regulation to ensure a design of uncertainty-tolerance power system. This review delves into the trade-offs linked with the implementation of mitigation strategies, such as reliability, computational speed, and economic efficiency. It also explores how these strategies may influence the planning and operation of future power grids.

We propose that, at equilibrium, statistically equal temperatures as mechanical torques are exerted on each kind of gas phase molecules as rates of translational action [@t=ʃmvds/dt=ʃmr2ωdϕ/dt=mv2, J]. These torques result from the impulsive density of resonant quantum fields with molecules, configuring the trajectories of gas molecules while balancing molecular pressure (p=NkT) against the density of field energy (J/m3). Gibbs energy fields contain no resonant quanta at zero Kelvin, with this measure of chemical potential diminishing in magnitude as translational action of the vapor molecules and quantum field energy increases with temperature. In illustration, we show how impulsive torques from quantum fields drive the reversible thermodynamics of Carnot’s heat-work engine cycle, sustain the decreasing atmospheric temperature gradient of increasing molecular entropy with altitude, support the translational action and field energy of vortical wind flow in anticyclones, frictionally warming the Earth’s surface while recycling greenhouse infrared absorption of surface radiation, generating electrical power from air flow in wind farms and destructive power in tropical cyclones. These cases all distinguish symmetrically between a causal field of impulsive quanta (Σhν) that energizes the action of matter and the resultant vis viva of molecular mechanics (mv2). The quanta of these different fields display mean wavelengths from 10-4 m to 1012 m, with mechanical advantages many orders of magnitude greater than the corresponding translational actions, though with mean quantum frequencies (v) similar to those of radial Brownian movement for independent particles (ω). These energy fields are also thermodynamically reversible reservoirs for heat, optimizing work processes on Earth and delaying the achievement of maximum entropy production from short wave solar radiation in conversion to outgoing long wave radiation to space.

Storing apples for up to a year is a well-established practice aimed at providing a continuous, locally-produced fruit supply to consumers and adapting to market trends for optimized profits. Temperature control is the cornerstone of postharvest conservation and apples are typically kept at temperatures from 0 to 3 °C. However, the energy-intensive process of the initial cool down and subsequent temperature maintenance poses significant financial challenges and contributes to the carbon footprint. Higher storage temperatures could reduce cooling-related energy usage but also pose the risk of enhanced ripening and quality loss. This work explores different storage technologies aiming to reduce energy consumption such as 1-methylcyclopropene, ultra-low oxygen and dynamic controlled atmosphere together with raised temperatures. The integration of advanced monitoring and control systems, coupled with data analytics and energy management in apple storage is also discussed. These sustainable strategies can be implemented without cost-intensive construction measures in standard storage facilities. Furthermore, beneficial side effects of higher storage temperatures in terms of a reduced occurrence of storage disorder symptoms and higher maintenance of quality attributes are also discussed for this special issue on sustainable horticultural production systems and supply chains.

At present, the world is at the peak of production of traditional fossil fuels. Much of the resources that humanity has been consuming (oil, coal and natural gas) are coming to an end. The human being faces a future that must necessarily go through a paradigm shift, which includes a progressive movement towards increasingly less polluting and energetically viable resources. In this sense, nanotechnology has a transcendental role in this change. For decades, new materials capable of being used in energy processes have been synthesized that undoubtedly will be the cornerstone of the future development of the planet. In this review, we report on the current progress in the synthesis and use of one-dimensional (1D) nanostructured materials (specifically nanowires, nanofibers, nanotubes and nanorods), with compositions based on oxides, nitrides, or metals, for applications related to energy. Due to its extraordinary surface-volume relationship, tunable thermal and transport properties, and its high surface area, these 1D nanostructures have become fundamental elements for the development of energy processes. The most relevant 1D nanomaterials, their different synthesis procedures, and useful methods for assembling 1D nanostructures in functional devices will be presented. Applications in relevant topics such as optoelectronic and photochemical devices, hydrogen production or energy storage, among others, will be discussed. The present review concludes with a forecast on the directions towards which future research could be directed on this class of nanostructured materials.

Traditional silicon binary circuits continue to face challenges such as high leakage power dissipation and large area of interconnections. Multiple-Valued Logic (MVL) and nano-devices are two feasible solutions to overcome these problems. In this paper, we present a novel method to design ternary logic circuits based on Carbon Nanotube Field Effect Transistors (CNFETs). The proposed designs use the unique properties of CNFETs, e.g., adjusting the Carbon Nanotube (CNT) diameters to have the desired threshold voltage and have the same mobility of P-FET and N-FET transistors. Each of our designed logic circuits implements a logic function and its complementary via a control signal. Also, these circuits have a high impedance state which saves power while the circuits are not in use. We show a more detailed application of our approach by designing a two-digit adder-subtractor circuit. We simulate the proposed ternary circuits using HSPICE via standard 32nm CNFET technology. The simulation results indicate the correct operation of the designs under different process, voltage and temperature (PVT) variations. Moreover, we designed a two-digit adder/subtractor and a power efficient ternary logic ALU based on the proposed gates. Simulation results show that the two-digit adder/subtractor using our proposed gates has 12X and 5X lower power consumption and PDP (power delay product) respectively, compared to previous designs.

This thesis completion works it out to deepen into diverse modeling techniques for Point Absorbers. A combined frequency-time domain model is conceived, designed and developed in Matlab with FoRtran as a base., leading to obtain physical variables of primary importance, namely position, velocity and power to Energy net balance relationships of absorption. Integration of different degrees of freedom with heave as main executable leads in turn to a single buoy motion focus. Acquisition of the needed hydrodynamic coefficients is provided though application of NEMOH & BEMIO solvers due to the Boundary Element Methodology. Initially, this Wave-to-motion model is validated through comparison with previous experimental results for a floating cone cylinder shape (Buldra-FO3). A single, generic, vertical floating cylinder is contemplated then, that responds to the action of the passing regular waves excitation. Later, two equally sized vertical floating cylinders aligned with the incident wave direction are modeled for a variable distance between the bodies. For both unidirectional regular and irregular waves as an input in deep water, we approximate the convolutive radiation force function term through the Prony method. By changing the spatial disposition of the axisymmetric buoys, using for instance triangular or rectangular shaped arrays of three and four bodies respectively, the study delves into motion characteristics for regular waves. The results highlight efficient layouts for maximizing the energy production whilst providing important insights into their performance, revealing displacement amplification- and capture width-ratios, while deriving in possible interpretations of scenarios related to the the known park effect. These terms are encompassed by the novelty of a new conceptual Post-Processing methodology in the field, which leads to obtain an optimal distance for the separated bodies with effective energy absorption in a regular wave regime. In conclusion, this computational excursion envisions and proposes potentials fields of study, which will surely enhance new connections and link this renewable energy form.

Jordan is classified as a low- to-middle-income, in which the primary energy sources are imported crude oil and natural gas. The energy expenses represent a high percentage of the country's GDP. Meanwhile, due to its geographical location and its climate, Jordan ranks very high among the world countries with respect to solar energy exploitation potential. Therefore, solar energy is a key resource that can be utilized to significantly improve both the country’s economy and energy security. It has to be highlighted that Jordan focus on a network dedicated to solar energy and it has to be mentioned the Erasmus Plus INNOMED Project based on virtual classrooms, which aims to promote innovative technologies and applications of solar energy in MENA Countries. This paper presents an overview of the solar energy resources in Jordan that includes: the current situation, the potential, and future expectations.

The flywheel is a widespread mechanical component used for the storage of kinetic energy and angular momentum. It typically consists of a cylindrical inertia rotating about its axis on rolling bearings, which involves undesired friction, lubrication, and wear. This paper presents an alternative mechanism that is functionally equivalent to a classical flywheel while relying exclusively on limited-stroke flexure-joints. This novel 1-degrees-of-freedom zero-stiffness mechanism has no wear and requires no lubrication: it is thus compatible with extreme environments, such as vacuum, cryogenics, or ionizing radiation. The mechanism is composed of two coupled pivoting rigid bodies whose individual angular momenta vary during motion but whose sum is constant at all times when the pivoting rate is constant. The quantitative comparison of the flexure-based flywheel to classical ones based on a hollow cylinder as inertia shows that the former stores typically 6 times less angular momentum and kinetic energy for the same mass while occupying typically 10 times more volume. The freedom of design of the shape of the rigid bodies offers the possibility of modifying the ratio of the kinetic energy stored versus angular momentum, which is not possible with classical flywheels. For example, a flexure-based flywheel with rigid pivoting bodies in the shape of thin discs stores 100 times more kinetic energy than a classical flywheel with the same angular momentum. A proof-of-concept prototype was successfully built and characterized in terms of reaction moment generation, which validates the presented analytical model.

This paper aims to explore how climate change affects electricity generation (fossil-fueled power plants, hydroelectric stations, wind systems and photovoltaics) and energy demand in residential buildings in Greece for the period up to 2050. In both cases RCP scenarios results are considered in the appropriate spatial and temporal dimension. Energy supply technologies were examined through statistical regression models and/or mathematical equations correlating climatic parameters with energy productivity. With respect to energy demand, bottom-up models were developed that integrate behavioral and policy aspects. The analysis showed that climate change is expected to mainly affect electricity generation from hydro and thermal power plants, while the impacts on solar and wind energy are significantly lower. The range of impacts on hydro potential and electricity generation depends on the geographical location of the power plants and shows significant uncertainty due to the corresponding uncertainty in climate models estimates regarding precipitation and runoff changes while showing significant geographical variations. With respect to energy demand, climate change is expected to affect energy consumption, but the expected range of effects depends on both the implementation and the characteristics (deep vs. shallow renovation) of measures for upgrading the thermal performance of the building stock and the intensity of climate change.

This literature review explores the relationship between energy markets development, environmental concerns, and geopolitics. By presenting a range of sources, we delve into essential themes like carbon emissions, the impact of energy markets deregulation on energy prices, trust in energy-related exchange-traded funds, the correlation between greenhouse gas emissions and global temperature anomalies, and how renewables regulations affect CO2 emissions. We also discuss relevant research on the impact of social and governance (ESG) considerations on financial performance. The geopolitical aspect is thoroughly presented under the energy framework. Topics, such as energy transitions in the Eastern Mediterranean and MENA regions and maritime oil piracy, are discussed. This review highlights the interdependent nature of these subjects and stresses the need for their interdisciplinary examination.

Over abundance of magnetic monopoles predicted by the Grand Unification Theories is inconsistence with current astronomical observation. The inflationary hypotheses with a vacuum energy deriving the exponential expansion can explain the two long-standing problems, flatness and horizon of the universe; and somehow suppress the abundance of monopoles. However, the dynamical scalar field has considerable uncertainties, which even leads to inflationary models separating from particle physics. This paper makes a small change, the early universe undergoes free expansion rather than an adiabatic one widely adopted, In such a case, the annihilation of abundant magnetic monopoles is just required in driving the inflation, so that the three long-term problems are automatically solved. On the other hand, the relic mass of failed annihilation of monopoles is responsible for the dark matter at present epoch. And ongoing annihilation on stars and compact objects corresponds to the dark energy. As monopole relics may exist in the form of monopole anti-monopole pairs, a new strategy of direct search is proposed.

Biodiesel has several drawbacks, such as being prone to oxidation, having reduced stability, and having limited storage time. Antioxidants compatible with biodiesel are being used to address its drawbacks. Utilizing antioxidants effectively improves the quality of biodiesel. Enhancing the quality of biodiesel for use as a clean energy source benefits both the global economy and ecology. Therefore, we believe that our work will contribute to the advancement of the worldwide industry. The study used blends consisting of 20% biodiesel and 80% diesel fuel. Isatin-thiosemicarbazones were tested as additives in blends at a concentration of 3000 parts per million (ppm) using an oxifast device. Comparing them to the chemical antioxidant Trolox. FT-IR, DSC, and TGA were used to characterize these samples. DSC measured sample crystallization temperatures (Tc). Samples with antioxidants showed decreased values compared to the non-antioxidant diesel sample D100. Several DSC tests were conducted to determine the antioxidant strengths of various samples. The results showed that the FT-IR spectrum's antioxidant effect regions grow clearer with antioxidants. The extra antioxidant is effective. Biodiesel's oxidative stability improves with isatin-thiosemicarbazones at varying concentrations. The kinetics of thermal decomposition of isatin-thiosemicarbazones under non-isothermal conditions have been determined using the Kissinger, Ozawa, and Boswell techniques. The activation energies of compounds 1 and 2 were calculated 137–147 kJ mol^-1 and 173–183 kJ mol^-1, respectively.

The construction field uses up over one-third of the global energy consumption and contribute to 40% of CO2 emissions according to the International Energy Agency (IEA) and the 2020 annual reporter of United Nation, Goal 11 (Make cities inclusive, safe, resilient and sustainable) which discusses sustainable, safe and efficient buildings. Therefore, Morocco has a commitment to this program by publishing the law 47-09 of energy efficiency. This work aims to study the energy efficiency of two types of building, a conventional and a natural building. Conventional building is constructed using concrete, while the natural one uses sand clay and straws. As for the technique of making the natural building, it perpetually follows the same approach accustomed in rural zones of Atlas Mountains in Morocco. In this research we also simulate, temperature and humidity variation inside these buildings using TRNSYS software. Sketch Up software was employed to design these houses. The weather database is used for a typical meteorological year (TMY). In the case of natural building, many building configurations were simulated: roof insulation, floor insulation, different types of glazing and sun protection. What's more, the thermal comfort is revealed to be more conspicuous in the case of natural building.

Coastal wave modeling and forecasting are essential in oceanography, sustainable marine energy, and ocean engineering. Precise forecasting of wave speed and direction are crucial for offshore operations, marine energy, risk management, environmental management, coastal and sustainable maritime management. The coastline of Brunei Darussalam can generate between 15 and 126 Giga Watt of wave energy. In this experimental research, we used two numerical approaches, the finite difference, and spectral element methods, to model and simulate wave speed and direction. We calculated the mean error between numerical and analytical solutions. We proposed a novel, promising, univariate time series forecasting model by combining the Long Short-Term (LSTM) with KerasTuner hyperparameters tuning and optimization techniques. This method helps us to improve the accuracy and efficiency of time-series forecasting.. The experimental data was computed from high-precision Acoustic Doppler Current Profiler (ADCP) sensor data. This research is part of the preliminary feasibility analysis of wave energy production in Brunei Darussalam and net zero commitment for a sustainable environment. Seven independent forecast experiments were performed for wave speed and direction in degree and radian units for 1, 3, 6, 8, 10, 12, and 24 hours. Mean squared error (MSE) was adopted as a metric for both training and testing. The experimental results reveal that the wave speed forecast has the lowest MSE compared to direction, regardless of the unit of measure, but has a longer duration. In addition, the direction forecast in the degree unit has the lowest errors compared to the unit of radians; the latter has a longer running time than the former. The model has delivered optimal results throughout the experiments with minor training and test errors. We conducted a thorough evaluations on two benchmark time series datasets, which include the study dataset and air quality index dataset, to validate the performance of the proposed model with other models. The proposed model outperforms cutting-edge forecasting models, such as the conventional LSTM, ARIMA, and Prophet. The model has the slightest forecast error compared to the existing literature’s result.

In this paper, the methodology using Insect Intelligent Building (I^2B) technology for establishing energy consumption monitoring system of public buildings is prevailed. The computing process node and distributed algorithm are utilized to implement the energy consumption collection and data transmission and data pre-processing. Taking a commercial building as a case study, CPNs are applied to set up the building energy consumption monitoring system, with the Spanning Tree Algorithm for generating network topology，and BPNN method for solving abnormal data and recovering missing data. The research results demonstrate the proposed method can effectively improve the performance of plug-and-play and self-identified and self-configuration of energy consumption monitoring system.

Climate change refers to a wide range of changes due to unstructured economic and human activities that impact the well-being status of all living and non-living things. Many adaptation and mitigation strategies focus on climate change solutions, at the center of which is the replacement of fossil fuels or other conventional energy sources with renewables. Mainly this is a contemporary issue for economies that seek ways to grow sustainably, such as developing countries. The purpose of the present study is to review how these renewable sources might have brought benefits for environmental improvement efforts within intense economic activities. Our effort targets the case of China since its efforts for transmission to a low-carbon country attract the world's research interest, given its significance in the global economic system. Mainly, this study’s attempt is based on searching relevant literature for potential changes in limiting greenhouse and carbon dioxide emissions toward China’s economic development status. The results of this study aim to become a valuable reference for further elaboration in light of climate change strategies with measurable outcomes in the growth process.

Microgrid is one of the promising green transition technologies that will provide enormous benefit to the seaport, as a solution to the major concerns in this sector, namely energy crisis, economical and environmental pollution. However, finest design of the microgrid is a challenging task considering different objectives, constraints and uncertainties involved. To ensure the optimal operation of the system, determining the right configuration framework and size for each component in the seaport microgrid at the minimum cost is a vital decision at the design stage. This paper aims to design a hybrid system of seaport microgrid with optimally sized component .The selected case study is the Port of Aalborg, Denmark. The proposed grid-connected structure consists of renewable energy sources (photovoltaic system and wind turbines), an energy storage system and cold ironing as seaport’ loads. The architecture is then optimized by utilizing HOMER to meet the maximum load demand by considering a few parameters such as solar global horizontal irradiance, temperature and wind resources. Then, the best configuration framework is analyzed in terms of economic feasibility, energy reliability and environmental impact.

Almost fifty years after the first installations, I identify the main lessons learned from fighting drought and poverty in Africa with direct solar-powered pumps thanks to Father Bernard Verspieren and Mali Aqua Viva. Six main findings and three main recommendations emerge from the present analysis. They are of direct relevance to all Africa’s countries whose population has gone from 438 million in 1977 to 1,308 million in 2019, with about 600 million still having no access to electricity. In place of “awareness campaigns” and extraordinary courses held by international organizations, I recommend to establish national solar energy institutes whose task will include the education of solar energy professionals giving practice-oriented workshops on solar-powered drip irrigation and rainwater harvesting throughout each Africa’s country. Said education will critically include the economic and social aspects of distributed “generation” of energy and water from sunlight and rainfall.

Sources are classified into two depending upon the factor of reviving. These sources, which cannot be revived into their original shape once they are consumed, are considered as nonrenewable energy resources, i.e., (coal, fuel) Moreover, those energy resources which are revivable to the original condition even after being consumed are known as renewable energy resources, i.e., (wind, solar, hydel) Renewable energy is a cost-effective way to generate clean and green electrical energy Now a day’s majority of the countries are paying heed to energy generation from RES Pakistan is mostly relying on conventional energy resources which are mostly nonrenewable in nature coal, fuel is one of the major resources, and with the advent of time their prices are increasing on the other hand RES have great potential in the country with the deployment of RES greater reliability and an effective power system can be obtained In this thesis, a similar concept is being used and a hybrid power system is proposed which is composed of intermixing of renewable and nonrenewable sources The Source side is composed of solar, wind, fuel cells which will be used in an optimal manner to serve load The goal is to provide an economical, reliable, uninterruptable power supply. This is achieved by optimal controller (PI, PD, PID, FOPID) Optimization techniques are applied to the controllers to achieve the desired results. Advanced algorithms (Particle swarm optimization, Flower Pollination Algorithm) will be used to extract the desired output from the controller Detailed comparison in the form of tables and results will be provided, which will highlight the efficiency of the proposed system.

Promoting the use of solar energy resources has always faced the challenges of instability and supply-demand mismatch. The key to solving these issues is to efficiently store and utilize solar energy resources using high-performance heat storage devices. This study designed a high-performance shell-and-tube phase change thermal storage device and established a numerical model using ANSYS software to summarize the device's dynamic melting law. To verify the accuracy of the numerical simulation, a performance testing platform for the phase change thermal storage device was built to investigate the impact of factors such as inlet water temperature, inlet water flow rate, type of heat storage, and initial temperature of the device, and to reveal the change law of the device's performance. The results show that the inlet water temperature has the most significant impact on the device's heat storage and release performance. When the device's heat storage or release is used for heating, changing the inlet water flow rate has a weak and limited effect on the device's performance. However, when the device's heat release is used to provide domestic hot water, increasing the makeup water temperature and reducing the inlet water flow rate can significantly improve the device's effective heat release. Furthermore, based on the experimental validation of the model's correctness, this study further simulated and studied the impact of different factors on the device's heat storage process to optimize its structural design and provide technical references for the device's actual operation and installation. The results show that the placement of fins has a negligible effect on the performance of the heat storage device while reducing the fin spacing and increasing the fin thickness can significantly improve the melting efficiency of the phase change material (PCM). Additionally, the heat storage characteristics of the device are significantly better in the vertical installation mode than in the horizontal installation mode. This study provides theoretical guidance and technical references for the design and use of phase change thermal storage devices.

From the standpoint of Neoliberal Institutionalism, this study explores Malaysia's participation in activities that make energy the topic and/or object of foreign policies, whether through bilateral or multilateral engagements. This research, which aims to evaluate the relevance of energy in Malaysia's economy and diplomacy and to explain Malaysia's reason for its involvement in these cooperations, is necessary because of Malaysia's growing involvement in the global energy market. Information for this study was gathered from a variety of government sources, interviews, published statistical data, and previous studies. The study demonstrates how vital energy is to Malaysia's economy. The Lao PDR-Thailand-Malaysia-Singapore Power Integration Project (LTMS-PIP) initiative, in which Malaysia is participating, is evidence of the viability of multilateral power commerce in the area. The Peninsula Gas Utilisation (PGU) pipeline in Peninsular Malaysia and the Four-Fuel Diversification Policy 1981 (4FDP 1981), which increases natural gas utilisation, are related to Malaysia's participation in the Malaysia-Thailand Joint Development Area (MT-JDA). Malaysia would want to think about streamlining its energy administration.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

Because of the near-term risk of extreme weather events and other adverse consequences from climate change, and, at least in the longer term, global fossil fuel depletion, there is world-wide interest in shifting to noncarbon energy sources, especially renewable energy (RE). Because of possible limitations on conventional renewable energy sources, researchers have looked for ways of overcoming these shortcomings by introducing radically new energy technologies. The largest RE source today is bioenergy, while solar energy and wind energy are regarded as having the largest technical potential. This paper reviews the literature on proposed new technologies for each of these three RE sources: microalgae for bioenergy, photolysis and airborne wind turbines. The main finding is that their proponents have underestimated the difficulties facing their introduction on a very large scale.

The development of novel ionic liquid crystals for energy storage applications has gained significant attention in recent years due to their potential to develop the field of energy storage. Ionic liquid crystals represent a unique class of materials with high ionic conductivity and thermal stability, making them ideal candidates for use in advanced energy storage devices. This research aims to explore the fundamental properties, structure and liquid crystals performance of these novel materials, with the goal of advancing their practical application in next-generation energy storage technologies. By understanding the structure-function relationship of ionic liquid crystals, researchers can tailor their properties to meet specific energy storage requirements, such as high energy density, fast charging capabilities, and long cycle life. This study seeks to contribute to the growing body of knowledge in the field of energy storage by investigating the potential of novel ionic liquid crystals as efficient and sustainable energy storage solutions. The two ionic liquid crystals show mesomorphic behavior and typical zwitterion characteristics that revealed by the cyclic voltammetry techniques. These materials uploaded with lithium ions for more stability and higher ionic conductivity.

The Internet of Things (IoT) is a promising technology for sensing and monitoring the environment to reduce disaster impact. Energy is one of the major concerns for IoT devices, as sensors used in IoT devices are battery-operated. Thus, it is important to reduce energy consumption, especially during data transmission in disaster-adverse situations. Clustering-based communication helps reduce a node’s energy decay during data transmission and enhances the network’s lifetime. Many hybrid combination algorithms are proposed for clustering and the routing protocol to improve the network lifetime in disaster scenarios. However, the performance of these protocols is widely varied based on the underlying network configuration and the optimisation parameters considered. In this research, we have used the clustering parameters that are most relevant to disaster scenarios, such as the node’s residual energy, distance to sink, and network coverage. Then, we proposed a bio-inspired hybrid (BAO-PSO) algorithm where the Butterfly Optimisation Algorithm (BOA) is used for clustering and Particle Swarm Optimisation (PSO) is used for the routing protocol. The performance of the proposed algorithm is compared with the benchmark protocols LEACH, DEEC, PSO, PSO-GA, and PSO-HAS. Residual energy, network throughput, and network lifetime are considered performance matrices. The simulation result showed that the proposed algorithm increases network lifetime by 10%-20% by comparison with the benchmark algorithm.

The present paper reports an exact approach quantifying the electromagnetic contribution to the anomalous magnetic moment occurring in isolated system comprised of non-composite particle carrying elementary electric charge. Essential averaging procedure and regularization of the electromagnetic field potentials necessary when quantifying the electromagnetic self-interactions and when deriving equations of motion without singularities and obeying the conservation laws are thoroughly discussed. The study shows that the dynamics of the considered system is associated to unique classical transcendental equations of motion satisfied by the particle's velocity and the electromagnetic contribution to the anomalous $g$-factor known from the quantum electrodynamics. The equations of motion lead to an exact analytical expression for the anomalous $g$-factor that provides more accurate result than that calculated with the aid of quantum electrodynamics. It matches the experimentally measured value reported in the literature to a one part per trillion. We obtain a_e=0.00115965218000(65) thus reveling the potential of non-perturbative, non-probability methods in predicting the electron's anomalous g-factor.

Ramsey’s economic theory of saving (RTS) estimates how much of its commodities a nation should save to safeguard the well-being of future generations. Since RTS retains many attractive qualities such as simplicity, strength, breadth and generality, here we ask if it would be useful to investigate biophysical issues. Specifically, we focus on a biological topic that lends itself as a backdrop for the study of the imbalance between intake and expenditure, i.e., the evaluation of the multicellular living organisms’ energetic requirements and constraints. Our problem is to find at each time the optimum distribution and the right balance of the cellular energy budget between consumption and storage: how much must a living organism spare to increase its chances of survival over long periods? Suggesting how to find the optimum allocation of the available energy between expenditure and saving at each time, RTS approaches to biological energy budgets may have a wide range of experimental applications, such as: a) optimization of the long-term survival chances of either immortalized cell cultures, or beneficial bacterial colonies and exogenous probiotic mixtures; b) eradication of detrimental biofilms, such as, e.g., heart valves’ Streptococcus colonies; c) novel anti-stress and anti-ageing strategies.

Here we propose a modification of the gravitational field on large scales as an alternate explanation for the discrepancy in the value of the Hubble constant as implied by Planck observations of the CMBR in the early Universe and that deduced from other distance indicators in the present epoch.

Energy use is of crucial importance for the global challenge of climate change but also an essential part of daily life. Hence, research on energy needs to be robust and valid. Other scientific disciplines have experienced a reproducibility crisis, that is, existing findings could not be reproduced in new studies, and energy research might be impacted as well. In this paper, we suggest the ‘TReQ’ approach to improve the research practices in the energy field and arrive at greater Transparency, Reproducibility, and Quality. We acknowledge the specific challenges of energy research and suggest a highly adaptable suite of tools that can be applied to research approaches across this multi-disciplinary and fast-changing field. In particular, we introduce preregistration of studies, making data and code publicly available, using preprints, and employing reporting guidelines to heighten the standard of research practices within the energy field. We argue that through wider adoption of these tools, we will be able to have greater trust in the findings of research used to inform evidence-based policy and practice in the energy field.

Energy consumption of processors and memories is quickly becoming a limiting factor in the deployment of large computing systems. For this reason it is important to understand the energy performance of these processors and to study strategies allowing to use them in the most efficient way. In this work we focus on computing and energy performance of the Knights Landing Xeon Phi, the latest Intel many-core architecture processor for HPC applications. We consider the 64-core Xeon Phi 7230, and profile its performance and energy efficiency using both its on-chip MCDRAM and the off-chip DDR4 memory as the main storage for application data. As a benchmark application we use a Lattice Boltzmann code heavily optimized for this architecture, and implemented using several different arrangements of the application data in memory (data-layouts, in short). We also assess the dependence of energy consumption on data-layouts, memory configurations (DDR4 or MCDRAM), and number of threads per core. We finally consider possible trade-offs between computing performance and energy efficiency, tuning the clock frequency of the processor using the Dynamic Voltage and Frequency Scaling (DVFS) technique.

Ever since oil was discovered in the Persian Gulf Region in the 1920s, the oil and gas industries have been dominant in the area. These countries are responsible for generating approximately 35 percent of the world's natural gas and 25 percent of its crude oil, making them the largest crude oil producers globally. The release of carbon dioxide (CO2) into the atmosphere is directly linked to the use of fossil fuels. CO2 accounts for 58.8 percent of all greenhouse gas emissions caused by human activities and has a detrimental impact on urban residents through the urban heat island effect. A significant portion of these emissions can be attributed to residential buildings. Some nations exacerbate the problem by relying excessively on fossil fuels. Oil-rich countries provide energy subsidies to the public in order to lower energy costs for their citizens. However, this policy can have negative consequences, including wasteful energy usage in countries like Iran.

The building and construction sector has a significant impact on CO2 emissions and pollutants released into the atmosphere, which contribute to climate change. The EPDB Directive mandates the achievement of a minimum energy class E for all residential buildings by 2030 and an energy class D by 2033. Particularly, in Italy, about 86% of the existing building stock predates the enactment of any energy laws and regulations, making it imperative to apply the energy efficiency interventions. This paper provides a support decision tool for the identification of standardized interventions on the envelope, air conditioning system and domestic hot water production. The study is focused on a specific construction period class (1976 - 1990) in six different climatic zones. The methodological approach is based on a cataloguing phase and definition of Ante Operam energy classes, on the case study identification, the energy requalification interventions identification, solutions simulations, cost estimation. By simulating standardized interventions for each climatic zone, a range of possible combinations will be identified. The most advantageous ones will be determined based on a cost-benefit analysis, considering the potential class jump achieved. The research result is a matrix of energy efficiency interventions that is applicable to each climatic zone and can be extended to the existing housing stock.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

Antibodies constitute a major component of serum on protein mass basis. We also know that the structural diversity of these antibodies exceeds that of all other proteins in the body and they react with an immense number of molecular targets. What we still cannot quantitatively describe is, how antibody abundance is related to affinity, specificity and cross reactivity. This ignorance has important practical consequences: we also do not have proper biochemical units for characterizing polyclonal serum antibody binding. The solution requires both a theoretical foundation, a physical model of the system, and technology for the experimental confirmation of theory. Here we argue that the quantitative characterization of interactions between serum antibodies and their targets requires systems-level physical chemistry approach and generates results that should help create maps of antibody binding landscape.

Bi0.5Na0.5TiO3-0.06BaTiO3 (BNT-BT) thin films were prepared by both chemical solution (CSD) and pulsed laser deposition (PLD). The microstructure, dielectric, and ferroelectric properties were investigated. High stability of the dielectric permittivity (∆ɛ/ɛ(150 °C) ≤ ± 15%) over a wide temperature range from room temperature to 300 °C was obtained. Distinctly, the CSD film showed high TCC stability with variation of ± 5% up to 250°C. Furthermore, the CSD film showed an unsaturated ferroelectric hysteresis loop characteristic of the ergodic relaxor phase, however the PLD one exhibited almost saturated loop signature of the coexistence of both ergodic and non-ergodic states. The energy storage properties of the prepared films were determined using the P–E loops obtained at different temperatures. The results showed that these films exhibit stable and improved energy storage density comparable to the ceramic capacitors. Moreover, the CSD film exhibited more rigidity and better energy storage density that exceeds 1.3 J/cm3 under low applied field of 317 KV/cm as well as interesting efficiency in a large temperature range. The obtained results are very promising for energy storage capacitors operating at high temperatures.

To facilitate wireless communication, ocean exploration, and various environmental and research applications, the underwater Internet of Things has been developed with an infrastructure of acoustic sensor networks. There has been a significant increase in failures and a decrease in the efficiency of the network due to the fluid and challenging underwater environment. Consequently, achieving quality of service (QoS) in underwater networks remains a research area. Supporting QoS in underwater sensor networks is challenging due to resource limitations such as processing power, memory, bandwidth, and power sources. The purpose of this study was to examine the service quality requirements as well as protocols that have been implemented in recent years. Finally, based on quality criteria, we have presented a routing solution based on fuzzy logic, which is more efficient than other recent methods regarding energy consumption rate, JFI, efficiency, and reliability.

This paper proposes an innovative postulate based on experimental observations, namely, that the speed of light can vary between two inertial reference systems. This postulate is defined as the principle of relative change in the speed of light, which refreshes the concept of absolute speed of light in traditional physics. By integrating the principle of the invariance of the speed of light with the principle of relativity in relativity theory, several important conclusions are derived: space and time must be capable of and proportionally expand and contract. Between two inertial reference systems with different relative speeds of light, objects have an energy difference of k^2 times, which induces a natural tendency for objects to move towards a state of lower energy. The acceleration is only related to the relative change rate of the speed of light in vacuum space and is independent of the mass of the object. The kinetic energy obtained by the object comes from the reduction of internal energy of the object, emphasizing the key role of energy conversion in this process. The paper provides a new theoretical perspective for explaining the physical mechanisms of universal gravitation and dark energy.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

This research introduces a novel approach to evaluate energy utilization in agribusiness within a cost-based framework, addressing the complexities associated with uncertain input energy content. The study focuses on the agricultural sector in Latin America, with particular emphasis on banana plantations, examining the sector's growing dependence on energy-intensive methods and inputs. We differentiate between technical and allocative efficiency, employing a frontier-based methodology. The analysis encompasses data from 21 state-owned banana plantations in Latin America, revealing significant room for improvement in energy efficiency. Our findings indicate an average Technical Efficiency of 0.69, Allocative Efficiency of 0.91, and overall Energy Efficiency of 0.59, suggesting potential reductions in input and energy consumption of up to 38%. The study underscores the importance of addressing both input mismanagement and misallocation to enhance energy efficiency. While the proposed methodology offers valuable insights for public sector enterprises, particularly in agriculture, further research is necessary to extend this approach to scenarios with uncertain input energy content, potentially incorporating stochastic frontier analysis or fuzzy logic methodologies.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

This paper investigates the use of deep learning techniques to perform energy demand forecasting. Specifically, the authors have adapted a deep neural network originally thought for image classification and composed of a convolutional neural network (CNN) followed by a multilayered fully connected artificial neural network (ANN). The convolutional part of the network was fed with a grid of temperature forecasting data distributed in the area of interest in order to extract a featured temperature. The subsequent ANN is then fed with this calculated temperature along with other data related to the timing of the forecast. The proposed structure was first trained and then used in a real setting aimed to provide the French energy demand forecast using ARPEGE forecasting weather data. The results show that the performance of this approach is in the line of the performance provided by the reference RTE subscription-based service, which opens the possibility to obtain high accuracy forecasting using widely accessible deep learning techniques through open-source machine learning platforms.

Reducing and time-shifting household energy demand is important for a sustainable transition of energy systems, and dynamic electricity pricing, like real-time pricing (RTP), is a popular instrument to incite households to change energy demand. However, the effect of such products relies on the assumption that dynamic price signals incorporate into everyday routines and rhythms. This paper investigates the flexibility of households’ everyday routines and rhythms. The study provides three insights based on 11 Danish household visits and interviews with electricity customers who are new to RTP. First, the interviews indicated confusion over terminology for dynamic pricing products and low interest in flexible energy demand. Second, everyday practices (already) appeared flexible but for other reasons than energy demand flexibility. Third, energy habits were important for providing meaning to everyday practices. In addition, the study shows that energy flexibility is not just about energy demand, but rather about all the other activities that form routines and rhythms in everyday life. We suggest 1) designing products that reflect ‘natural’ or ‘societal’ daily rhythms, 2) focusing on the engaged households, and 3) being aware that for some households, changes in pricing, including new payment schemes, might put extra pressure on already harried everyday routines.

Remote patient monitoring systems are helpful since they can provide timely and effective healthcare facilities. Such online telemedicine are usually achieved with the help of sophisticated and advanced wearable sensor technologies. The modern type of wearable connected devices enables the monitoring of vital sign parameters such as: heart rate variability (HRV) also known as electrocardiogram (ECG), blood pressure (BLP), Respiratory rate and body temperature. The ubiquitous problem of wearable devices is power demand for signal transmission, such devices require frequent battery charge which causes serious limitations to the continuous monitoring of vital data. To overcome this, the current study provides a primary report for collecting kinetic energy from human daily activities for monitoring Human vital signs, the harvested energy is used to sustain the battery autonomy of wearable devices, which enables longer monitoring time of vital data. A thorough review of available commercial ECG devices is first provided, and different methods evaluated in other literature to improve the monitoring time of wearable IOT devices. Besides, a novel type of Stress or exercise ECG monitoring device based on Microcontroller PIC18F4550 and Wi-Fi device ESP8266 is proposed in this study, which is cost effective and enables real time monitoring of heart rate on cloud during normal daily activities. In order to achieve both portability and maximum power, the harvester has smallest structure and low friction. Neodymium magnets are chosen for their highest magnetic force. Due to nonlinear magnetic force interaction of the magnets, the nonlinear part of the dynamic equation has inverse quadratic form. Electromechanical damping is considered in this study and the quadratic non linearity is approximated using MacLaurin expansion, which enables to find the law of motion for general case of studies using classical methods for dynamic equations and find the suitable parameters for the harvester. The oscillations are enabled by applying an initial force and there is loss of energy due to the electromechanical damping. A typical numerical application is computed with Matlab software and ODE45 solver is used to verify the accuracy of the method.

Data centres, though a necessary part of modern society, are being stigmatised for consuming vast amounts of electricity for their operational and cooling needs. Due to Ireland’s reliance on fossil fuels to meet the increased energy demand of data centres, the data centres are contributing significantly to Ireland’s total carbon emissions. As much of this energy is expelled from data centres as waste heat energy, the potential for recycling some of this wasted heat energy was explored using environmentally friendly systems from recent publications. The recovered waste heat energy was applied in a vertical farming system, and the benefits of this waste heat to the vertical farm were analysed and quantified in two scenarios. Using conservative estimates, it was predicted that each vertical farm could be between 5-23% the size of the data centre and produce enough food to feed between 14-61 adults their daily calorie needs, and between 13-58 people their daily fresh produce requirements, depending on the scenario applied. For a more accurate prediction, each vertical farm would have to be assessed on a case-by-case basis. However, there was not enough data available on Irish data centres to perform these calculations.

The deep energy method (DEM), a type of physics-informed neural network, is evolving as an alternative to finite element analysis. This method employs the principle of minimum potential energy to predict deformations under static loading conditions. However, the model’s accuracy is contingent upon choosing the appropriate architecture for the model, which can be challenging due to the high interactions between hyperparameters, large search space, difficulty in identifying objective functions, and non-convex relationships with the objective functions. To improve DEM’s accuracy, we first introduce random Fourier feature (RFF) mapping. RFF mapping helps with the training of the model by reducing bias towards high frequencies. The effects of six hyperparameters are then studied under compression, tension, and bending loads in planar linear elasticity. Based on this study, a systematic automated hyperparameter optimization approach is proposed. Due to the high interaction between hyperparameters and the non-convex nature of the optimization problem, Bayesian optimization algorithms are used. The models trained using optimized hyperparameters and having Fourier feature mapping can accurately predict deflections compared to finite element analysis. Additionally, the deflections obtained for tension and compression load cases are more sensitive to variations in hyperparameters than bending.