Solid-state fermentation (SSF) is the bioprocess where microorganisms are cultivated in the absence of free water under control conditions. Lactic acid can be produced by fermenting grape stalks with Rhizopus oryzae in SSF. During the microorganism growth, the temperature and water content of the solid bed fluctuate, leading to areas of either dry or excessive moisture in the solid substrate. Therefore, it's crucial to control the supply of water to the matrix. In this work, we obtain lactic acid through SSF of grape stalks using Rhizopus oryzae NCIM 1299. The SSF was conducted at a fixed temperature of 35 °C, with three constant relative humidity levels: 50, 65, and 80 %RH. Mathematical models, including the Logistic and First Order Plus Dead Time models for fungal biomass growth and the Luedeking and Piret with Delay Time model for lactic acid production, were adjusted to kinetic curves. Growth kinetic parameters (Xmax, μmax, Tp, T0, Yp/x and td) were determined for all conditions. These kinetic parameters were then correlated with relative humidity using a second-degree polynomial relationship. We observed a decrease in Xmax with increasing %RH, while the value of Yp/x increased at higher %RH. Finally, the optimal variable relative humidity profile was obtained by applying the Dynamic Optimization Technique, resulting in a 15.30% increase in lactic acid production.

Lodging poses a significant challenge to rice yield, prompting the need to identify elite alleles for lodging resistance traits to improve cultivated rice varieties. In this study, a natural population of 518 rice accessions was examined to identify elite alleles associated with plant height (PH), stem diameter (SD), stem anti-thrust (AT/S), and various internode lengths: (first (FirINL), second (SecINL), third (ThirINL), fourth (ForINL), and fifth (FifINL) internode lengths). 262 SSR markers linked to these traits were uncovered through association mapping in two environmental conditions. Phenotypic evaluations revealed striking differences among cultivars, and genetic diversity assessments showed polymorphisms across the accessions. Favorable alleles were identified for PH, SD, AT/S, and 1 to 5 internode lengths, with specific alleles displaying considerable effects. Noteworthy alleles include RM6811-160 bp on chromosome 6 (which reduces PH) and RM161-145 bp on chromosome 5 (which increases SD). The study identified a total of 42 novel QTLs. Specifically, seven QTLs were identified for PH, four for SD, five for AT/S, five for FirINL, six for SecINL, five for ThirINL, six for ForINL, and four for FifINL. QTLs qAT/S-2, qPH2.1, qForINL2.1, and qFifINL exhibited the most significant phenotypic variance (PVE) of 3.99% for the stem lodging trait. AT/S, PH, ForINL and FifINL had additive effects of 5.31 kPa, 5.42 cm, 4.27cm and 4.27cm, respectively, offering insights into eight distinct cross-combinations for enhancing each trait. This research suggests the potential for cross-breeding superior parents based on stacked alleles, promising improved rice cultivars with enhanced lodging resistance to meet market demands.

Colletotrichum lini is a flax fungal pathogen, comprising differently virulent strains. In this work, we sequenced the genomes of three C. lini strains of different virulence: high virulent #390-1, medium virulent #757, and low virulent #771. We obtained more than 100× genome coverage with Oxford Nanopore Technologies reads and more than 50× genome coverage with Illumina data. To construct high-quality genomes, several assembly strategies were tested. The final assemblies were obtained using the Canu – Racon ×2 – Medaka – Polca scheme and were 54.0-55.3 Mb in length, contained 26-32 contigs, had an N50 > 5 Mb and the BUSCO completeness > 96%. Comparative analysis of the constructed genomes showed high similarity between mitochondrial and nuclear genomes. However, a rearrangement event and the loss of a 0.9 Mb contig were revealed. The candidate effectors were predicted in sets of proteins received after genome annotation. The obtained genome sequences of C. lini strains extend the knowledge on the genetic diversity of Colletotrichum species and are the basis for establishing molecular mechanisms of pathogenicity of the flax pathogen and effective control of flax anthracnose.

This pioneering study explores the geospatial and temporal patterns of natural and human-induced disasters from 1900 to 2024, providing essential insights into their global distribution and impacts. Utilizing the comprehensive international EM-DAT database, our analysis reveals significant trends and disparities in disaster occurrences and their widespread consequences. Results showed a dramatic escalation in both natural and man-made (technological) disasters over the decades, with notable surges in the 1991-2000 and 2001-2010 periods. A total of 25,836 disasters were recorded worldwide, of which 69.41% were natural disasters (16,567) and 30.59% were man-made (technological) disasters (9,269). The most significant increase in natural disasters occurred from 1961-1970, while man-made (technological) disasters surged substantially from 1981-1990. Seasonal trends reveal that floods peak in January and July, while storms are most frequent in June and October. Droughts and floods are the most devastating in terms of human lives, while storms and earthquakes cause the highest economic losses. The most substantial economic losses were reported during the 2001-2010 period, driven by catastrophic natural disasters in Asia and North America. Our research highlights Asia as the most disaster-prone continent, accounting for 41.75% of global events, with natural disasters making up 61.89% of these events. Oceania, despite experiencing fewer total disasters, shows a remarkable 91.51% of these as natural disasters. Africa is notable for its high incidence of man-made (technological) disasters, which constitute 43.79% of the continent's disaster events. Europe, representing 11.96% of total disasters, exhibits a balanced distribution but tends towards natural disasters at 64.54%. Examining specific countries, China, India, and the United States emerged as the most frequently affected by both natural and man-made (technological) disasters. The impact of these disasters has been immense, with economic losses reaching their highest during the decade of 2010-2020, largely due to natural disasters. The human toll has been equally significant, with Asia recording the most fatalities and Africa the most injuries. Particularly, the decade from 2001 to 2010 experienced the greatest economic losses, primarily driven by natural disasters in Asia and North America. These insights highlight the urgent need for tailored disaster risk management strategies that address the distinct challenges and impacts in various regions. By understanding historical disaster patterns, policymakers and stakeholders can better anticipate and manage future risks, ultimately safeguarding lives and economies.

Negative corona discharges occur widely in high voltage transmission lines and charged aircraft, which can cause strong electromagnetic interference. Negative corona discharge is typically performed simultaneously at multiple discharge points. In this study, the current and its EM radiation characteristics of single-needle and multi-needle negative corona discharge in different conditions were tested. The current and electromagnetic radiation characteristics of the two discharge structures were compared. The dipole radiation model was established to analyze the EM radiation characteristics of the negative corona discharge.The results show that, It is only when the voltage reaches a certain threshold that the current and electromagnetic radiation fields of the multi-needle discharge structure will be superimposed and their amplitudes will increase significantly. The frequency of electromagnetic radiation signal does not change with the number of needles, cathode geometry and applied voltage, but only depends on ambient pressure. It provides a basis for detecting corona discharge sources under different conditions.

Introduction: In Traditional Chinese Medicine (TCM), tongue diagnosis plays an important role. Besides shape, colour and textural attributes of tongue regions have significance due to their association with different organs (viz. heart, lung, kidney-bladder, liver-gallbladder and stomach-spleen) in health and disease. Although numerous quantitative methods have been proposed to reduce inter and intra observer variability in tongue diagnosis, almost all of them considered only global colour/ textural features i.e. from entire body of tongue. In this work, regional colour and texture information of tongue have been analysed for healthy subjects (NOM) and patients suffering from chronic acidity-indigestion (ACD). Methods: Tongue boundaries are marked manually in each image and then tongue bodies are automatically partitioned into five regions linked with said internal organs. Rough assessments of regions’ boundaries are obtained from literature and then they are fine-tuned according to experts’ advice. As boundaries are not well defined, regions near the common boundary of two or more organs, are not assigned to any organ. Several first and second order statistical features based on grey scale intensities and a* values of LAB colour space (indicative of redness) have been extracted from five different regions of tongue images. Intragroup analysis using Wilcoxon signed rank test compared different regions within individual study group. Additionally, intergroup analysis using Wilcoxon rank sum test compared tongues of NOM with ACD for each region separately. Results: Intragroup analysis reveals a* values are statistically different (p<0.01) between stomach-spleen and liver-gallbladder regions for ACD while no significant change of a* are noted between these regions of normal tongue. It was found from intergroup analysis that correlation (one of the second order texture features extracted from grey scale images) of heart region has significantly decreased while correlation of kidney, liver-gallbladder and stomach-spleen regions significantly increased from NOM to ACD. Conclusion: This study sheds light on importance of inclusion of regional textural analysis of tongue in quantitative studies and can be applied to automated tongue diagnosis for other diseases.

We define a spinor-Minkowski metric for SL(4,C). It is not a trivial generalization of the SL(2,C) metric and it involves the Minkowskian one. We define 4x4 version of the Pauli matrices and eight 4-component associated generalized eigenvectors that can be regarded as undotted covariant spinors. The 4-component spinors can be grouped into four categories. Each category transforms in its own way. The outer products of pairwise combinations of 4-component spinors can be associated with 4-vectors. Including the dotted covariant, undotted and dotted contravariant forms totally we have sixteen pairs of spinors. Eight of them live in the conjugate space which has no countepart in SL(2,C).

Although cicadas have traditionally been considered pests of little or no importance, since the beginning of this century, an increase in damages is being recorded in olive groves of southern Spain. According to our hypothesis, the new agricultural practices would be behind it. During 2024, Intensive sampling has been carried out in organic grove, with herbaceus cover (VC2), and a second one with mixed vegetation cover (VC1, in which the crushed remains of the annual pruning are added). In both ecological groves, inventories of the vegetation have been carried out, as well as intensive sampling in the olive canopy, with the densities of oviposition injuries being recorded and compared with respect to conventional management (CONV). The objectives of this study: (1) to quantify the density of oviposition lesions under these three different farming systems; (2) to determine priority areas for cicadas oviposition within trees; (3) to develop a sampling method to assess damage over large areas. The results show significant increases in density of injuries in organic groves, with maximum values recorded in the olive grove with mixed cover. Oviposition injuries show an altitudinal gradient distribution, with maximum values in the lower zone. The factors involved are discussed.

The present study evaluates mold fungal resistance of newly developed loose-fill thermal insulation materials from wheat straw, corn stalk and water reed. Three different processing methods of raw materials was performed by mechanical crushing (Raw, ≤ 20 mm), thermal-mechanical pulping (TMP) using 4% NaOH and steam explosion pulping (SEP). An admixture of boric acid (8%) and tetraborate (7%) was applied to all processed substrates due to their anti-fungal properties. Additionally, the fourth sample group was prepared from SEPs of all raw species without boric acid and tetraborate (SEP*) as control. Samples from all treatments were separately inoculated by 5 different fungal species and incubated in darkness for 28 days at 28 ℃ and RH >90%. The highest resistance to the colonization of mold fungi was achieved by TMP and SEP processing coupled with addition of boric acid and tetraborate, where molds infest only around 35% to 40% of the inoculated sample area. The lowest mold fungi resistance was detected for Raw and SEP* samples, each ~75% that was affected by rich amount of accessible nutrients, suggesting that boric acid and tetraborate additives alone did not prevent mold fungal growth as effective as in combination with TMP and SEP treatments. Together, the achieved fungal colonization scores after combined fungicide and pulping treatments are acceptable for the application of various renewable materials in future thermal insulation product development.

Fiber coupling efficiency is one of the key technical indicators of atmospheric laser communication, which directly affects the communication system BER. According to the optical fiber coupling efficiency model, the optical fiber coupling model under atmospheric slant link is established, and the relationship between wavelength, zenith angle, receiving aperture, altitude and coupling efficiency is studied through numerical simulation. Based on the principle of adaptive optics turbulence correction, the relationship between fiber coupling efficiency and adaptive optics order is established. A fast method for estimating the coupling efficiency based on Strehl ratio is proposed. According to the principle of laser communication system, the semi-physical simulation experimental system of atmospheric slant-range channel coupling efficiency is constructed, and the coupling efficiency test and analysis are completed.

This research is completed in development of researches devoted to relations between elastic modulus (MoE) and thermal expansivity (CTe) of different materials. This study experimentally confirmed the relation of MoE and CTe for thermosetting polymers and FRPs both under normal and heating temperatures. As the thermosetting polymers, the epoxy compositions were used and glass fiber and mineral additives for FRP. The experiment was based on dilatometric and elastic deformations’ testing. Also, the relaxation model of MoE/CTe was proposed, that is based on physical properties of polymers’ supramolecular structures. The comparative analyzing of MoE/CTes’ different models is done. The most accurate models are determined, and the relaxation model has demonstrated the high accuracy.

Introductions- Liveable housing environments face the menace of global climate change. In-frastructure (including buildings and houses) continuously experiences significant impacts ex-acerbated by natural variability in climate. The study addressed how climate change impacts the resilience of residential buildings, increased maintenance frequency, and the wellbeing and comfort of residents in UK residential buildings. Design/Methodology/Approach: This study used deductive reasoning and an empirical epis-temological methodology as a data-collecting basis to evaluate primary information obtained via a questionnaire. Regression analysis was ultimately employed to analyse the collected da-ta. Result/Discussions: The findings show a significant relationship between climate change and the wellbeing of the occupants of UK residential buildings. Also, the results show that social wellbeing is more important to the occupants than mental and physical wellbeing. It reveals that residential buildings in the UK suffer the cost of maintenance due to continuous reduc-tion in the building fabric's resilience to the impacts of climate change; for instance, a recent increase in rainfall/storms results in unprecedented flooding, which continues to damage the UK residential building fabrics.

The study investigated roles of institutional types and ethnic/racial background on academic credit among the traditionally underrepresented population of the U.S. study abroad program. Using archival data, the study sampled the student’s enrollment and academic credit information spanning a period of 20 years (2003 - 2022). Data analysis Using One-Way Analysis of Variance (ANOVA) indicates significant main influence of institutional type (p<.001) and significant main influence of ethnic/racial identity (p<.001) on students’ academic credit. The result was discussed in terms of its relevance in educational policy re-evaluations, improvement of the study conditions of the underrepresented students, and enhancement of the enrollment opportunities of these minority population across all U.S. institutions of learning.

(1) Background: Mixed Reality is a technology that has gained attention due to its unique capabilities for accessing and visualizing information, becoming a valuable tool for medicine, particularly for the operating room and surgical learning; (2) Methods: A systematic review was conducted following the PRISMA guidelines to answer the research questions established using the PICO framework; (3) Results: Although implementation of Mixed Reality applications in the operations room presents some challenges, when used appropriately, it can yield remarkable results. It can make learning easier, flatten the learning curve for several procedures, and facilitate various aspects of the surgical processes; (4) Conclusion: Technical complexity, equipment costs, and steep learning curves present significant obstacles to the widespread adoption of Mixed Reality and computer-assisted evaluation. The possibility of integration of distinct medical imaging modalities and innovative functionalities holds promise for clinical applications. However, it is important to consider issues related to usability, bias, and statistical analyses need consideration. Mixed Reality offers significant benefits, but there are still open challenges such as ergonomic issues, limited field of view, and battery autonomy that must be addressed to ensure widespread acceptance.

In order to the effect of hydrated phase change materials on suppressing coal spontaneous combustion, the thermogravimetric experiment and reaction activation energy analysis experiment were used to explore the changes of combustion characteristic, parameters characteristic temperature and activating energy of gas coal, long flame coal, meagre coal, and lean coal before and after adding hydrated phase change materials. The research results showed that hydrated phase change materials increased the coal samples’characteristic temperature point and have effective inhibitory effects on different stages of oxidation process.However, the effect was best at low temperatures, as hydrated phase change materials undergo phase change and absorb heat when heated at low temperatures, isolating coal from contact with oxygen. The activating energy increased by 1.138 KJmol-1～23.048 KJmol-1 and the mass loss reduced by 1.6%～9.3% after the inhibition of the coal sample,indicating that the oxidation rate of various coal samples can be slowed down and the spontaneous combustion can be suppressed by using hydrated phase change materials.At the same time, this material can also reduce the combustibility index of meagre coal and lean coal, as well as the comprehensive combustion index and maximum loss rate of long flame coal and gas coal.

This review explores the transformative impact of sensor technologies in early disease detection. It highlights recent advancements in nanotechnology-based sensors, particularly focusing on their applications in identifying disease biomarkers at early stages. The integration of these sensors with artificial intelligence for predictive analytics in healthcare is also discussed. Applications in cancer, infectious diseases, and chronic disease management underscore their diverse utility. Challenges in sensor technology adoption and future directions, including multiplexed sensors and wearable devices, are examined. This review underscores sensors' potential in enhancing disease management and patient outcomes.

Legumes develop root nodules that harbour endosymbiotic bacteria, rhizobia. These rhizobia convert nitrogen to ammonia by biological nitrogen fixation. A thorough understanding of the biological nitrogen fixation in legumes and its regulation is key to develop sustainable agriculture. It is well known that plant hormones affect nodule formation; however, most studies are limited to model legumes due to their suitability for in vitro, plate-based assays. Specifically, it is almost impossible to measure the effects of exogenous hormones or other additives during nodule development in crop legumes such as soybean as they have huge root system in soil. To circumvent this issue, the present research develops suitable media and growth conditions for efficient nodule development under in vitro, soil free conditions in an important legume crop, soybean. Moreover, we also evaluate the effects of all major phytohormones during soybean nodulation under identical conditions. This versatile, inexpensive, scalable and simple protocol provides several advantages over previously established methods. It is extremely time-and resource-efficient, does not require special training or equipment, and produces highly reproducible results. The approach is expandable to other large legumes as well as for other exogenous additives.

The present study examined metabolites in Northern wild rice (WLD), the impact of WLD supplemented high fat (HF) diet on gut microbiota, short chain fatty acids (SCFAs) and correlation with metabolism or inflammation versus HF+white rice (WHR) in mice. C57BL/6J mice received HF diet supplemented with 26g% WHR, 26g% WLD, or 13g% WHR+13g% WLD (WTWD) for 12 weeks. The levels of fasting plasma glucose, total cholesterol, triglycerides, insulin resistance, inflammatory cytokines and monocyte adhesion were lower, and the abundances of fecal Lactobacillus gasseri species bacteria and propionic acid were higher in HF+WLD diet-fed mice compared to HF+WHR diet-fed mice (p<0.05). The anti-inflammatory effects of HF+WTWD diet were weaker than that in HF+WLD diet, but were greater than that in HF+WHR diet-fed mice (p<0.05). Relative abundances of fecal Lactobacillus gasseri and propionic acid in HF+WLD fed-mice were higher than that in HF+WHR fed mice. The abundance of fecal L. gasseri and propionic acid negatively correlated with metabolic and inflammatory markers (p<0.05). The findings suggest that WLD dose-dependently attenuated metabolic and inflammatory disorders in HF diet-fed mice. Interactions between WLD components and gut microbiota may upregulate fecal propionic acid and contribute to metabolic and anti-inflammatory benefits of WLD diet-induced insulin resistant mice.

Blocking the interaction of the SARS-CoV-2 spike protein with the human angiotensin-converting enzyme II (hACE2) protein serves as a therapeutic strategy for treating COVID-19. Traditional Chinese medicine (TCM) treatments containing bioactive products could alleviate the symptoms of severe COVID-19. However, the emergence of SARS-CoV-2 variants has complicated the process of developing broad-spectrum drugs. As such, the aim in this study was to explore the efficacy of TCM treatments for SARS-CoV-2 variants through targeting the interaction of the viral spike protein with the hACE2 receptor. The antiviral activity was systematically evaluated using a pseudovirus system. Scutellaria baicalensis was found to be effective against SARS-CoV-2 infection through affecting the interaction of viral spike protein with the hACE2 protein. The active molecules of S. baicalensis were identified and analyzed. Baicalein and baicalin, a flavone and a flavone glycoside, respectively, found in S. baicalensis, exhibited strong inhibitory activities, targeting the viral spike protein or hACE2 protein, respectively. Under optimized conditions, virus infection was inhibited by 98% via baicalein-treated pseudovirus and baicalin-treated hACE2. In summary, we identified the potential SARS-CoV-2 inhibitors of the interaction of the Omicron spike protein and hACE2 receptor from S. baicalensis. Future studies on the therapeutic application of baicalein and baicalin against SARS-CoV-2 variants are needed.

In the present study. At first, some properties of r-fuzzy soft β-closed sets are introduced on fuzzy soft topological spaces based on the paper Aygunoglu et al. (Hacet. J. Math. Stat. 2014, 43, 193-208). Also, we define the closure and interior operators with respect to the classes of r-fuzzy soft β-closed and r-fuzzy soft β-open sets, and investigate some of their properties. In addition, the concept of r-fuzzy soft β-connected sets is introduced and characterized with help of fuzzy soft β-closure operators. Thereafter, some properties of a fuzzy soft β-continuity are studied. Furthermore, we introduce and study the concepts of fuzzy soft almost (weakly) β-continuous functions, which are weaker forms of a fuzzy soft β-continuity. Also, the relationships between these classes of functions are specified with the help of some illustrative examples. Finally, we explore new types of fuzzy soft functions called, fuzzy soft β-irresolute (strongly β-irresolute, β-irresolute open, β-irresolute closed and β-irresolute homeomorphism) functions, and discuss some properties of them. Also, we show that fuzzy soft strongly β-irresolute → fuzzy soft β-irresolute → fuzzy soft β-continuity, but the converse may not be true.

The high transmissibility, rapid evolution, and immune escape of SARS-CoV-2 variants can influence the course of infection and, in turn, morbidity and mortality in COVID-19, posing a challenge in controlling transmission rates and contributing to the emergence and spread of new variants. The factors that shape viral genetic variation are consequently essential for understanding the evolution and transmission of SARS-CoV-2, especially in vaccinated individuals where immune response plays a role in the progression and spread of this disease. This study assessed. In this context, we evaluated the impact of immunity induced by the CoronaVac vaccine (Butantan/Sinovac) on intra-host genetic diversity, analyzing 118 whole-genome sequences of SARS-CoV-2 from unvaccinated and vaccinated patients infected with the Gamma variant. Vaccination with CoronaVac favors negative selection at the intra-host level in different genomic regions and prevent greater genetic diversity of SARS-CoV-2, which may help reduce the emergence of new mutations, reinforcing the importance of vaccination in reducing virus transmission.

The prevalence of multidrug-resistant Gram-negative infections, particularly carbapenem-resistant strains, has become a significant global health concern. Ceftazidime-avibactam (CZA) has emerged as a promising treatment option. However, data on its efficacy and safety in children are scarce, necessitating further investigation. We conducted a retrospective study at a tertiary hospital in Spain from February 2019 to January 2022. Pediatric patients (<16 years) treated with CZA for confirmed or suspected multidrug-resistant Gram-negative infections were included. Clinical and microbiological characteristics, treatment approaches, and outcomes were examined. Eighteen children received CZA treatment. All had complex chronic conditions, with the most frequent underlying main diseases being liver transplantation (n=8) and biliary atresia (n=4). The predominant type of infection for which they received CZA was intra-abdominal infections caused or suspected to be caused by OXA-48-producing Klebsiella pneumoniae. CZA was generally well tolerated. Within the first month of starting CZA therapy, 2 patients died, with one case directly linked to the infection’s fatal outcome. Some patients needed repeated courses of therapy due to recurrent infections, yet no resistance development was noted. In summary, the use of CZA showed effectiveness and safety, while the lack of resistance development highlights CZA’s potential as a primary treatment option against OXA-48-producing infections.

The objective of this study, which is divided into two parts, is twofold: to address long standing challenges in the sensing of atmospheric turbulence-induced wavefront aberrations in strong scintillation conditions via comparative analysis of several basic scintillation resistant wavefront sensing (SR-WFS) architectures and iterative phase retrieval (IPR) techniques (Part I, this paper), and to develop a framework for the potential integration of SR-WFS techniques into practical closed-loop non-astronomical atmospheric adaptive optics (AO) systems (Part II). In this paper we consider basic SR-WFS mathematical models and phase retrieval algorithms, tradeoffs in sensor design and phase retrieval technique implementation, and methodologies for WFS parameter optimization and performance assessment. The analysis is based on wave-optics numerical simulations imitating realistic turbulence-induced phase aberrations and intensity scintillations, and optical field propagation inside SR-WFSs. Several potential issues important for practical implementation of SR-WFS and IPR techniques such as requirements for phase retrieval computational grid resolution, tolerance with respect to optical element misalignments, and the impact of camera noise and input light non-monochromaticity are also considered. Results demonstrate that major wavefront sensing requirements desirable for AO operation in strong intensity scintillations can potentially be achieved by transitioning to novel SR-WFS architectures based on iterative phase retrieval techniques.

The Linear Fresnel Reflectors are a solar concentration technology that is versatile and can serve many industrial processes or thermal conditioning. Such collectors entail a certain footprint, generating shading on the surface where they are installed. This effect is rarely quantified but may play an indirect role on the surface below. When installed on a roof, the solar radiation heats the building less. In places where the annual heating demand is higher than the cooling demand, this constitutes an asset. However, this becomes a disadvantage when the cooling demand is higher annually than the heating demand. Essentially, the reduced solar radiation allows the growth of plants that would not grow without the shade provided by the collector. The present paper is a quantitative analysis of such shading based on the Linear Fresnel Reflector of the Cyprus Institute. The work was conducted using the Tonatiuh++ ray-tracing software to determine the annual radiation blocking. A total of four years of actual meteorological measurements were applied directly to the ray-tracing model.

Germanium (Ge) nanostrip is embedded in polymer and studied as a waveguide. Measurement reveals that this new type of semiconductor/polymer heterogeneous waveguide exhibits strong absorption for the TE mode from 1500 nm to 2004 nm, while the propagation loss for the TM mode declines from 20.56 dB/cm at 1500 nm to 4.89 dB/cm at 2004 nm. The transmission characteristics serves as an essential tool to verify the optical parameters (n-κ) of the thin strips, addressing to the ambiguity raised by spectroscopic ellipsometry regarding highly absorbing materials. Furthermore, the observed strong absorption for the TE mode at 2004 nm is well beyond the cut-off wavelength of the crystalline bulk Ge (~1850 nm at room temperature). This redshift is modeled to manifest the narrowing of the Tauc-fitted bandgap due to the grain order effect in the amorphous Ge layer. The accurate measurement of the nanometer-scale light-absorbing strips in a waveguide form is a crucial step toward the accurate design of integrated photonic devices that utilize such components.

Turbidity is an important water quality parameter, especially for drinking water. The ability to actively monitor the turbidity level in Drinking Water Distribution Systems is of critical importance to the safety and wellbeing of the public. Traditional turbidity monitoring methods involve manual collection of water samples at set locations and times followed by laboratory analysis, which are labor intensive and time consuming. Fiber-optic measurement permits real-time, in-situ turbidity monitoring. But the current technology is based on plastic fibers, which suffer from high optical attenuation and hence are unsuitable for large-scale remote monitoring. In this paper, we report the demonstration of a fiber-optic turbidity sensor based on multi-mode glass fibers. The system uses a single fiber to both deliver laser light into the water sample and collect the back-scattered light for detection. A balanced-detection scheme is utilized to remove the common-mode noise to enhance the turbidity sensitivity. Highly linear turbidity responses are obtained and a turbidity resolution as low as 0.1 NTU is achieved. The test unit is also shown to have excellent reproducibility against repeated measurements and good stability against temperature changes. Turbidity measurement in real environmental matrices such as tap water and pond water is also reported with an assessment of the impact of flow rate. This work demonstrates the feasibility of future large scale distributed fiber-optic turbidity monitoring networks.

The Sun is a frame at relative rest in which sunlight travels at the emitted speed c. Earth travels at the revolving speed v in this frame. The reflection of light as a mechanical phenomenon applies to the modified Michelson interferometer employed by Miller in his experiments with light from the Sun. Unlike the Tomaschek experiments, which use light from stars that may travel in the Universe at velocities different from that of the Sun, the fringe shifts in the Miller experiments are predictable. Based on Michelson's derivation, Miller expected in his experiments at Mount Wilson a 1.12 fringe shift and observed a fringe shift of 0.08 in 1921 and 0.088 in 1925. The reflection of light as a mechanical phenomenon predicts zero fringe shift for Miller's experiment agreeing only with his observations at the Cleveland laboratory in 1924.

Measurement-Device-Independent Quantum Key Distribution (MDI-QKD) is a two-photon protocol devised to eliminate eavesdropping attacks that interrogate or control the detector in realized quantum key distribution systems. In MDI-QKD, the measurements are carried out by an untrusted third party, and the measurement results are announced openly. Knowledge or control of the measurement results gives the third party no information about the secret key. Error-free implementation of the MDI-QKD protocol requires the crypto-communicating parties, Alice and Bob, to independently prepare and transmit single photons that are physically indistinguishable, with the possible exception of their polarization states. In this paper, we apply the formalism of quantum optics and Monte Carlo simulations to quantify the impact of small errors in wavelength, bandwidth, polarization and timing between Alice's photons and Bob's photons on the MDI-QKD quantum bit error rate (QBER). Using published single-photon source characteristics from two-photon interference experiments as a test case, our simulations predict that the finite tolerances of these sources contribute (4.04+/-20/N_sifted) to the QBER in an MDI-QKD implementation generating an N_sifted-bit sifted key.

Compound parabolic concentrators are relevant systems used in solar thermal technology. With adequate tailoring, they can be used as an efficient and low-cost alternative in residential water applications. This work presents a simulation study using a ray tracing methodology. With this technique we simulate the interaction between solar rays and solar concentrator to quantify the amount of energy that impinges on the receiver at a particular time. Energy availability is evaluated in a comparison of two configurations: stationary at 21° throughout the year and multi position setup; tilted with respect to the horizontal depending on three seasonal positions: 0° for summer, 16° for spring / autumn and 32° for winter, with the objective of increasing the amount of available energy in each season. The fact that a tracking system can be dispensed with also represents an economical option for the proposed application. The results showed that at 21°, the proposed system works satisfactorily; however, by carrying out the selected angular adjustments, the overall energy availability increased by 22%, resulting in a more efficient option. The methodology developed herein proved to be a valuable tool for prototype design and performance evaluation.

High-performance properties of interpenetration polymer network (IPN) hydrogels, based on physically crosslinked chitosan (CS) and chemically crosslinked poly(N-isopropylacrylamide) (PNiPAM), have been successfully developed. The IPN of CS/PNiPAM is proposed to overcome the limited mechanical properties of the single CS network. In this study, the viscoelastic behaviors of prepared materials in both solution and gel states have been extensively examined, considering the UV exposure time and crosslinker concentration as key factors. The effect of these factors on gel formation, hydrogel structures, thermal stabilities of networks, and HeLa cell adhesion were studied sequentially. The sol-gel transition was effectively demonstrated through the scaling law, which agrees well with Winter and Chambon's theory. By subjecting the CS hydrogel to the process operation in an ethanol solution, its properties can be significantly enhanced with increased crosslinker concentration, including the shear modulus, crosslinking degree, gel strength, and thermal stability in its swollen state. The IPN samples exhibit a smooth and dense surface with irregular pores, allowing for much water absorption. The HeLa cells were adhered to and killed using the CS surface cationic derivative, then released through hydrolysis by utilizing the hydrophilic/hydrophobic switchable property or thermo-reversible gelation of the PNiPAM network. The results demonstrated that IPN is a highly attractive candidate for anti-fouling materials.

Neisseria gonorrhoeae is a bacterium that causes the sexually transmitted infection gonorrhea. This study employed molecular docking simulations to investigate potential interactions between natural molecules and the Fe(3+) ions import ATP-binding protein fbpC in Neisseria gonorrhoeae FA 1090. Among the screened molecules, Hypericin exhibited a remarkable binding energy of approximately -13.2 kcal/mol, indicating a robust and favorable binding affinity with the target protein. This promising outcome suggests that Hypericin could serve as a potential candidate for further exploration as a therapeutic agent against Neisseria gonorrhoeae infections. However, it is imperative to emphasize that these in silico findings necessitate experimental validation through in vitro and in vivo studies to ascertain the actual efficacy and safety of Hypericin as a treatment option.

Salmonella causes various type of disease worldwide with a remarkable pace. Salmonella enteric serotype typhi (S. typhi), a gram-negative bacterium (only cause disease in man) is the mainly causative agent of Typhoid fever. Typhoid fever is most common in poor and unprivileged developing countries of Asia and Africa. One of the major components of virulence factors produced during salmonella infection is Lipid A, which acts as a potent human immuno-modulator bacterial endotoxin. Regulation of Lipid A biosynthetic pathway occurs at second step, catalyzed by LpxC, a Zn2+ dependent metalloamidase. Systematic Screening of a pool of drug datasets like natural products library from Zinc database, Asinex database, Thiophene analogues fruitfully provided us 3 potent lead molecules s1_dl_mseq2, s1_ll_mseq2, and s2_ll_mseq8 which actively binds with LpxC enzyme and could be developed into sound inhibitors of LpxC enzyme after the application of drug development and processing strategies. Wet lab experimentation is required to validate these results for further use.

Diesel contamination of farming soils is of great concern because hydrocarbons are toxic to all forms of life and can potentially enter the food web through crops or plants used for remediation. Data on plant ability to uptake, translocate and accumulate diesel-derived compounds are controversial not only due to the probable diverse attitude of plant species but also because of the lack of a reliable method to distinguish petrogenic from biogenic compounds in plant tissues. The purpose of this study was to set up a GC-MS-based protocol enabling the determination of diesel-derived hydrocarbons in plants grown in contaminated soil for assessing human and ecological risks, predicting phytoremediation effectiveness and biomass disposal. To this aim two plant species Vicia sativa L. and Secale cereale L., belonging to two diverse vascular plant families, were used as plant models. They were grown in soil spiked with increasing concentrations of diesel fuel and the produced biomass was used to set up the hydrocarbon extraction and GC-MSD analysis. The developed protocol was also applied to the analysis of Typha latifolia L. plants, belonging to a different botanical family and grown in a long-time and highly contaminated natural soil. Results showed the possibility of distinguishing diesel-derived compounds from biogenic hydrocarbons in most terrestrial vascular plants, just considering the total diesel compounds in the n-alkanes carbon range C10-C26, where the interference of biogenic compounds is negligible. Diesel hydrocarbons quantification in plant tissues was strongly correlated (0.92<r2<0.99) to the concentration of diesel in spiked soils, suggesting a general ability of the considered plant species to adsorb and translocate relative low amounts of diesel hydrocarbons and the reliability of the developed protocol.

The Serra da Estrela Natural Park (NPSEs) in Portugal stands out as a well-preserved region abundant in medicinal plants, particularly known for their pharmaceutical applications in diabetes prevention and treatment. This comprehensive review explores these plants' botanical diversity, traditional uses, pharmacological applications, and chemical composition. The NPSEs boast a rich diversity with 138 medicinal plants across 55 families identified as traditionally and pharmacologically used against diabetes globally. Notably, the Asteraceae and Lamiaceae families are prevalent in anti-diabetic applications. In vitro studies reveal their significant inhibition of carbohydrate-metabolizing enzymes, and certain plant co-products regulate genes involved in carbohydrate metabolism and insulin secretion. In vivo trials demonstrate anti-diabetic effects, including glycaemia regulation, insulin secretion, antioxidant activity, and lipid profile modulation. Medicinal plants in NPSE exhibit various activities beyond anti-diabetic, such as antioxidant, anti-inflammatory, antibacterial, anticancer, and more. Chemical analysis identifies over fifty compounds like phenolic acids, flavonoids, terpenoids, and polysaccharides responsible for their efficacy against diabetes. The findings underscore the potential of NPSE medicinal plants as anti-diabetic candidates, urging further research to develop effective plant-based anti-diabetic drugs, beverages, and supplements.

A reduction of melatonin function contributes to the acceleration of Alzheimer's disease (AD), and understanding molecular processes of melatonin-related signaling is critical for intervention of AD progression. Recently, we synthesized and tested a series of melatonin derivates with donepezil fragments in silico and in vitro. In this study, one of the most potent compounds, 3c, was studied in an in vivo rat model of pinealectomy (pin) and subsequent icvAβ1-42 infusion. Melatonin was used as a referent drug. The treatment with melatonin and 3c (10 mg/kg, i.p. for 14 days) exerted a beneficial effect on memory decline and concomitant rise of Aβ1-42 and pTAU in the hippocampus in the pin + icvAβ1-42 rats. Melatonin supplementation facilitated the non-amyloidogenic signaling via a non-receptor (histone deacetylase sirtuin 1, SIRT1) and receptor-related signaling (MT/ERK/CREB). The hybrid 3c derivate up-regulated the MT1A and MT2B receptors, pERK and pCREB. Our findings strongly support the hypothesis that melatonin-related derivates may become a promising drug candidate in AD therapy.

In recent decades, there have been numerous endeavors to develop a novel category of survival distributions possessing enhanced flexibility through the extension of existing distributions. This article constructs and validates the statistical properties of a novel survival distribution in order to obtain an alternative distribution that is suitable for analyzing survival data by presenting the novel mixture of the Fréchet distribution along with statistical properties such as the probability density function (PDF), cumulative distribution function (CDF), rth ordinary moment, skewness, kurtosis, moment-generating function, mean, variance, mode, survival function, hazard function, and asymptotic behavior, as well as constructing the estimators of the unknown parameter by employing the expectation-maximization (EM) algorithm, and simulated annealing. Additionally, the performance of the proposed estimators was compared with bias, mean squared errors (MSE), and simulated variances, and given an illustrative example of the proposed distribution to the survival data set in order to show that the proposed distribution is appropriate for the right-skewed data. This will be extremely advantageous in survival analysis.

This work considers the existence of heteroclinic solutions for second order differential equations with ϕ-Laplacians and generalized impulsive conditions on the real line. For the construction of the results, it was only imposed that ϕ is a homeomorphism and the Schauder’s fixed point theorem allied with the concepts of L1-Carathéodory functions and sequences together with the equiconvergence on infinity and on each impulsive moments. Finally, a practical part illustrates the main theorem.

Coded aperture 3D imaging techniques have been rapidly evolving in the recent years. The two main directions of evolution are in aperture engineering to generate the optimal optical field and in development of computational reconstruction to reconstruct the object’s image from the intensity distribution with a minimal noise. The goal is to find the ideal aperture-reconstruction method pair and if not, to optimize one to match the other for designing an imaging system with required 3D imaging characteristics. Lucy-Richardson-Rosen algorithm (LR²A), a recently developed computational reconstruction method was found to perform better than its predecessors such as matched filter, Weiner filter, phase-only filter, Lucy-Richardson algorithm and non-linear reconstruction (NLR) for certain apertures when the point spread function (PSF) is a real and symmetric function. For other cases of PSF, NLR performed better than the rest of the methods. In this tutorial, LR²A has been presented as a generalized approach for any optical field along with MATLAB codes for reconstruction of any image when the PSF is known. The common problems and pitfalls in using LR²A has been discussed. Simulation and experimental studies for common optical fields such as spherical, Bessel, vortex beams and exotic optical fields such as Airy, scattered and self-rotating beams have been presented. From this study, it can be seen that it is possible to transfer the 3D imaging characteristics from non-imaging type exotic fields to indirect imaging systems faithfully using LR²A. The application of LR²A to medical images such as colonoscopy images and cone beam computed tomography images with synthetic PSF has been demonstrated. We believe that the tutorial will provide a deeper understanding of computational reconstruction using LR²A.

Abstract: In the Western of Mekong Delta belong to Vietnam a amount of alluvium sediments flows from upstream China to Vietnam, they are going from the river branches to in the Mekong Delta, then get out the Western Sea of Vietnam. This sediments accumulated gradually elevation the new land. The increase elevation of the land creates a fertile coastal plain where mangrove forests with a rich ecosystem of plants and animals. Over time, these forests change, with different plant species succeeding each other. This aims of this study to finding plant species in the forest, classification of forest types based on ecological regions, assessement the biodiversity of tree species, and compare the abundance communities, measuring the growth of the forest in these regions. In 2023, a comprehensive survey was conducted by using a systematic approach. The number of survey plots have done depend on the density of the forest, Base on the width of the forest range, the number of survey plots from 500m to 1,000m set up 1-2 plots, sub region set up from 10 to 15 plots. In total, 68 plots have done established in the erea, the area of plot is 100 square meters (10m x 10m). Using the statistical software in forestry to survey and analysis data. The result provided a complete picture of the tree species composition, distribution, and community structure characteristics in each ecological sub-region. The result of survey showed in the sub-region 1 have seven species as Sonneracia ovate, Rhzophora apiculata, Excoecaria agallochha, Avicennia officinalis, Avicennia alba, Agricerasvcoculatum, Bruguiera gymnorhiza. In the sub region 2 have eleven species as Sonneracia caseolaris, Annona reticulata, Lumnitzera littorea, Lumnizera racemosa, Rhizophora apiculata, Excoecaria agallocha, Avicennia officinalis, Avicennia alba, Hibiscus tillacerus, Bruguiera gymorhiza, Aericeras comiculatum. In the sub region 3 have eight as Sonratia caseolaris, Rhizophora mucronata, Rhizophora apiculata, Excoecaria agallocha, Avicennia marine, Avicennia alba, Bruguiera gymorhiza. In the region 4 have ten species as Sonneracia caseolaris, Sonneracia ovate, Lumnizera racemosa, Rhizophoa apiculata, Excoecaria agallocha, Avicennia marina, Avicennia officinalis, Aviecnnia alba, Bruguiera gymorhiza, Bruguiera cylindrica The total species of the mangrove forest in the Western Mekong Delta have 16 species from 11 plant families have been identified. Among these species have 6 dominant species include Avicennia oficinali),Avicennia alba, Rhizophora apiculata, Excoecaria agallocha, Someratia caseolaris, and Bruguiera yipamoriza. Two species easy grow on the new land are Avicennia officinalis Avicennia alba this findings show they can develope on the original new land for the shore of the Western Mekong Delta. The surveyed results also calculated the average of the height, diameter (D1.3), canopy, health of the nature mangrove tree for each sub region and total region. From these results showed the division of foresty structure, the structure of height, diameter (D1.3), canopy, vitality of the sub region and total region in the Western Mekong Delta.

The paper discusses the design and modeling of a simple and illustrative hardware kit for teaching the basics of quantum cryptography to engineering students. The novel solution differs from those already on the market in that it is focused on familiarising trainees with the physical principles of quantum key distribution, as well as with the basics of mathematical formalism in quantum mechanics. This is achieved by using a minimally sufficient set of optical elements with a simple mathematical description in the Jones formalism. This composition of the kit is targeted mostly at engineering students and does not require advanced training in physics as a prerequisite. The configurable architecture of the hardware educational kit contributes to the deeper involvement of students. By independently changing the modular configuration of the system, students can conduct experiments that were not directly provided by the developers. For instance, students can assess the impact of choosing the basic settings of phase retarders on the course of a man-in-the-middle attack. The proposed amount of mathematical and informational support, as well as ready-made formal models, is sufficient to reasonably put forward hypotheses for experimental verification and interpret the obtained empirical data. At this moment, the hardware kit is being replicated, distributed and successfully applied at universities and companies in the communications industry. The accumulated experience of educational use testifies to the high efficiency of the kit as a tool for basic QKD training for people without prior knowledge of quantum mechanics. A discrete event model simulating the operation of the hardware kit is implemented in the non-commercial modeling software CPN Tools and is openly distributed.

For many years marine algae has been subject of numerous researches and as a source of natural products with antiviral activity, such as terpenes, alkaloids and sulphated polysaccharides. However, the anti-Zika virus (ZIKV) potential of algae has not been studied. In this study we evaluated extracts seven species of the three major classes of seaweeds (Phaeophyceae, Chlorophyceae and Rhodophyceae) against ZIKV. All seaweeds tested are native of the Brazilian coast, except for Kappaphycus alvarezii that can be cultivated. ZIKV a mosquito-borne flavivirus, has become a public health problem. In recent years there has been an increase in the number of cases and a strong association between ZIKV outbreak and the spread of cases of Guillain-Barré Syndrome and microcephaly. All seaweed extracts tested in this work inhibits ZIKV replication in a dose-dependent manner. Caulerpa racemosa, Kappaphycus alvarezii and Osmundaria obtusiloba extracts were able to inhibit viral replication at low concentrations with EC₅₀ values ranging from 1.38 to 1.98 µg/mL. We observed that O. obtusiloba presented a significant virucidal effect. Our results suggest that extracts of C. racemosa, K. alvarezii and O. obtusiloba presented very promising results, being excellent candidates for further studies, demonstrating that marine algae are an interesting source for the development of novel anti-ZIKV agents.

Vibrio vulnificus (Vv) is a bacterial pathogen native to warm and brackish water ecosystems that can cause fatal septicemia (Vv-vibriosis) in humans and various farmed fish species. From a One Health perspective, controlling Vv-vibriosis outbreaks on farms is essential not only for animal but also for human health, as it reduces the risk of Vv transmission to humans. Electrolyzed water (EW) is a sustainable control method, exhibiting transient disinfectant properties due to the formation of hypochlorous acid (HOCl). We hypothesized that EW could effectively reduce Vv populations in aquaculture facilities, preventing outbreak emergence. To test this hypothesis, survival assays in EW were conducted under varying conditions of salinity, pH, and free available chlorine (FAC). The results indicated that an intermediate concentration of FAC had a significant bactericidal effect on Vv populations regardless of the condition and tested strain. Consequently, the strategic use of EW could serve as an eco-friendly preventive and control measure against Vv-vibriosis by significantly decreasing the bacterial load in farm water.

This study investigates the impact of DNA methylation on phenotypic diversity in chickpeas (Cicer arietinum). By analyzing DNA methylation landscapes across various chickpea cultivars, we aim to decipher the evolutionary processes underlying phenotypic variation. Using bisulfite sequencing and advanced genomic techniques, we identified significant methylation patterns associated with key adaptive traits. Our findings provide novel insights into the role of epigenetic modifications in plant evolution and offer potential applications in crop improvement.

This study investigates the impact of DNA methylation on phenotypic diversity in chickpeas (Cicer arietinum). By analyzing DNA methylation landscapes across various chickpea cultivars, we aim to decipher the evolutionary processes underlying phenotypic variation. Using bisulfite sequencing and advanced genomic techniques, we identified significant methylation patterns associated with key adaptive traits. Our findings provide novel insights into the role of epigenetic modifications in plant evolution and offer potential applications in crop improvement.

A 70-year-old female with a significant medical history of hypertension, hypothyroidism, chronic back pain, and a left hip prosthetic joint infection experienced complications following a total hip replacement. After multiple revisions and eventual discharge to a rehabilitation facility, she developed surgical site bleeding and a femoral head dislocation extending into the pelvis. At our hospital, imaging revealed a failed hip arthroplasty with extensive damage and infection, necessitating complex revision surgery and an antibiotic regimen. During her treatment, she developed a diffuse rash diagnosed as vancomycin-induced hypersensitivity reaction (DRESS), prompting a switch to oral linezolid and systemic corticosteroids. Despite transient eosinophilia and elevated inflammatory markers, her condition stabilized, and she was discharged with instructions for follow-up. This case underscores the importance of vigilant monitoring and timely intervention in managing complex postoperative infections and drug reactions.

Corrugated board is a composite material characterized by strong orthotropy in both the elastic and plastic phases. Additionally, due to its layered structure, which consists of alternately arranged flat and wavy layers of paper, its mechanics becomes complicated. Therefore, a precisely selected set of laboratory tests is needed to correctly identify all the necessary material parameters of cardboard. The work attempts to define a full set of laboratory tests in order to determine material parameters describing the linear-elastic, orthotropic behavior of cardboard and the basic parameters defining popular plasticity criteria, such as the asymmetric orthotropic Hoffman criterion. For this purpose, sensitivity analysis and numerical models of several selected basic laboratory tests were used. Since the aim of the work is to choose appropriate laboratory tests necessary to correctly determine the material parameters of corrugated board (not its individual layers), the numerical models do not contain detailed cardboard geometry, but only its homogenized representation in the form of the flat shell models. All numerical models are based on the nonlinear finite element method and constitutive modelling in the form of UMAT subroutines implemented in the ABAQUS software. Based on the analyses, appropriate measurements and laboratory tests were indicated that are most sensitive to the material parameters sought.

Sorghum grain processing can improve the nutritional content by promoting dietary properties that contribute to food security and economic development. The quality, nutritional content, and processing properties of sorghum bicolor grain can greatly affected by the inbred line races and variance in pericarp colour.The current study assessed the influence of the Husking Fraction Time Units (HFTU) process, which employed set time units per second (S), on the variation in the nutritional profile of fifty-one inbred line sorghum varieties based on distinct pericarp colours. When the assessment of the nutritional profile was involved: dry matter, total protein besides, namely mineral (P, K, S, Ca, Mg, Na, Fe, Zn, and Mn). The variety groups showed a significance value of (P < 0.05), indicating the study hypothesis's truth.The results demonstrated substantial impacts implied by the Husking Fraction Time Unit (HFTU) technique. This occurrence was noted when the dry matter percentage was increased in the husked products, specifically the endosperm (grits) and bran. The protein percentage redistributed by 19.2% compared to the whole grain and bran content. In comparison, the ratio of N/S was 14:1 in the S. bicolor and 12:1 in the kafirin in the bran part. Moreover, a strong correlation was observed among the examined minerals of S.bicolor and kafirin, such as the correlation between Ca: P, K: Na, and Fe: Zn attributed 80 (S) time unit, with correlation coefficients of R = 0.784 and R = 0.586, R= 517, R= 0.884, R= 0.745, and R = 0.893, respectively. At the same time, the 80 (S) time unit showed a significant effect on the colour property profile.The study results could benefit breeders and nutrition specialists in developing genotypes and processing sorghum grains, promoting research, and aiding several industrial sectors owing to the grain's adaptability and nutritional properties.

The microalgae Phaeodactylum tricornutum (PT) is distinguished by its rich nutrient profile, characterized by well-documented neuroprotective activities, including fucoxanthin (FX), a major carotenoid, and polyunsaturated omega-3 fatty acids (n-3 PUFA). The current study aims to evaluate the protective effects of a standardized extract of PT (Mi136) containing 2% FX on cognitive function, oxidative stress, and inflammation parameters in a mouse model of accelerated aging. Seventy-two (72) male mice were randomly assigned to the blank control group (BC), negative control group (NC), and four similar microalgae extract of PT groups (branded as BrainPhytTM) with different human equivalent doses. From day 01 to day 51, mice in the BC group were injected with a 0.9% normal saline solution, while mice in all other groups were subcutaneously injected with D-galactose (D-Gal) at a dose of 150 mg/kg once per day, five days per week. Results indicated that, for the three higher microalgae extract of PT dose groups, spatial cognitive function, swim latency, and step-through latency impairments induced by chronic D-Gal intoxication were significantly and fully inhibited, with mean values similar to those in the BC group during each day of testing. Similar benefits were observed in biochemical analysis, specifically regarding brain and plasma levels of lipid peroxidation, TNF-α, and IL-6 markers. These data underscore the positive effects of a standardized extract of PT containing 2% FX on cognitive function parameters such as spatial working memory, long-term memory, and short-term memory through the regulation of oxidative stress and inflammation pathways.

Small-scale fisheries are significant sources of nutrition and livelihood globally. However, increasing anthropogenic activities in coastal areas of developing countries have threatened the sustainability of artisanal fisheries and species. Fisheries of Sardinella maderensis (Lowe, 1838), to which Nigeria contributes 9% of the global stock and is a significant livelihood source in the coastal communities of Ibeju-Lekki, Lagos, face sustainability threats. This research investigated the effects of anthropogenic activities on S. maderensis fishery in the coastal areas of Ibeju-Lekki, Lagos, Nigeria. The study adopted a mixed-method approach involving qualitative and quantitative research methods. These include species identification, water quality analysis, land use change analysis, field surveys, focus group discussions and interviews. Results show genetic analysis of the fish samples from six stations revealed that the species had a mean of 98% similarity to Sardinella maderensis in NCBI. Multiple linear regression indicates that anthropogenic variables explained approximately 4.62% of the variance in the fish catch (p &lt; .001, R2 = .05). Water samples showed heavy metal levels were above international limits, high total petroleum hydrocarbon (TPH) pollution in all stations (27.56 mg/L- 3985.40 mg/L). Physiochemical analysis of water samples indicated TDS higher than acceptable limits (Mean = 24971.1 mg/L) and inadequate chlorophyll-a level (Mean = 0.01 µg/L). Hence, urgent strategies are required to mitigate anthropogenic threats through inclusive coastal management policies supporting resilient artisanal fisheries and marine spatial planning.

The goal of this work is to develop a sustainable value chain of carbonaceous adsorbents that can be produced from the solid fibrous digestate (SFD) of biogas plants and further applied in integrated desulphurisation-upgrading (CO2/CH4 separation) processes of biogas to yield high purity biomethane. On this purpose, physical and chemical activation of the SFD derived biochar was optimised to afford micro-mesoporous activated carbons (ACs) of high BET surface area (590-2300 m2g−1) and enhanced pore volume (0.57-1.0 cm3g−1). Gas breakthrough experiments from fixed bed columns of the obtained ACs, using real biogas mixture as feedstock, unveiled that the physical and chemical activation conclude to different types of ACs which are sufficient for biogas upgrade and biogas desulphurisation respectively. Performing breakthrough experiments at three temperatures close to ambient it was possible to define the optimum conditions for enhanced H2S/CO2 separation. It was also concluded that the H2S adsorption capacity is significantly affected by restriction to gas diffusion. Hence, the best performance was obtained at 50 oC and the maximum observed in the H2S adsorption capacity vs the temperature is attributed to the counterbalance between adsorption and diffusion processes.

Steam boiler has a significant role in the industrial sector. The failure in boiler tubes significantly reduces the availability of the plant. Furthermore, deposits on the inner tube wall contribute to such failure by changing the thermal resistance of the wall, which causes a significant increase in the tube wall's temperature and, consequently, lower allowable stress. The presented thermal-fluid model is developed for the water tube. The model is implemented using ANSYS FLUENT to estimate the wall maximum water tube wall temperature considering the deposits layer and then determine the minimum thickness of the tube wall via ASME standards to assure safe operation. The model is verified via a mesh independence test. The minimum tube thickness is recommended and justified given the thermo-mechanical performance of the water tubes at several operating loads of 50, 75, and 100 %. These loads are implemented by different convective heat transfer coefficients of flue gases under different deposit thicknesses, thermal conductivity, and flue gas temperature. The present work contributes to the literature by recommending the minimum thickness of the water wall tubes and highlighting the thermo-mechanical effect of the deposits on water tube resilience under different operating conditions.

We report a diode pumped solid state (DPSS) laser used for intracavity pump-enhanced difference frequency generation (DFG) to create a 3.5 micron laser. Using a 50 mm-long periodically poled lithium niobate (PPLN) crystal inside the cavity of an Nd:YVO4 solid state laser at 1064 nm with 4.5 W pump power at 808 nm, and a 310 mW C-band signal at 1529 nm, up to 31 mW of mid-infrared output power at 3499 nm is obtained. The cavity requires no active stabilization and/or locking, and the entire cavity is &lt;8 cm in length. The obtained output power corresponds to a black box efficiency of 2.20 %W-1, which is the highest value reported to date for continuous wave DFG based on a bulk nonlinear optical crystal with no active stabilization. Potential future applications in free space optical communication are discussed as well.

We experimentally demonstrate enhanced spectral broadening of femtosecond optical pulses after propagation through silicon-on-insulator (SOI) nanowire waveguides integrated with two-dimensional (2D) graphene oxide (GO) films. Owing to the strong mode overlap between the SOI nanowires and the GO films with a high Kerr nonlinearity, the self-phase modulation (SPM) process in the hybrid waveguides is significantly enhanced, resulting in greatly improved spectral broadening of the femtosecond optical pulses. A solution-based, transfer-free coating method is used to integrate GO films onto the SOI nanowires with precise control of the film thickness. Detailed SPM measurements using femtosecond optical pulses are carried out, achieving a broadening factor of up to ~4.3 for a device with 0.4-mm-long, 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of ~3.5 and the effective nonlinear figure of merit (FOM) by a factor of ~3.8, relative to the uncoated waveguide. Finally, we discuss the influence of GO film length on the spectral broadening and compare the nonlinear optical performance of different integrated waveguides coated with GO films. These results confirm the improved nonlinear optical performance for silicon devices integrated with 2D GO films.

Mirrors are a subset of optical components essential for the success of current and future space missions. Most of the telescopes for space programs ranging from Earth Observation to Astrophysics and covering the whole electromagnetic spectrum from X-rays to Far-Infrared are based on reflective optics. Mirrors operate in diverse and harsh environments that range from Low-Earth Orbit, to interplanetary orbits and the deep space. The operational life of space observatories spans from minutes (sounding rockets) to decades (large observatories), and the performance of the mirrors within the mission lifetime is susceptible to degrade, which results in a drop of the instrument throughput, which in turn affects the scientific return. Therefore, the knowledge of potential degradation mechanisms, how they affect mirror performance, and how to prevent them is of paramount importance to ensure the long-term success of space telescopes. In this review we report an overview on current mirror technology for space missions with a focus on the importance of degradation and radiation resistance of the coating materials. A special attention will be given to degradation effects on mirrors for the far and extreme UV as in these ranges the degradation is enhanced by the strong absorption of most contaminants.

Xyleborus beetles, a diverse group of ambrosia beetles, present significant challenges to forestry and agriculture due to their damaging burrowing behavior and symbiotic relationships with fungi. This review synthesizes current knowledge on the biology, ecology, and management of Xyleborus. We explore the beetles' life cycle, reproductive strategies, habitat preferences, and feeding habits, emphasizing their ecological and economic impacts. Control and management strategies, including preventive measures, chemical and biological control, and integrated pest management (IPM), are critically evaluated. Recent advances in molecular genetics and behavioral studies offer insights into genetic diversity, population structure, and host selection mechanisms. Despite progress, managing Xyleborus effectively remains challenging. This review identifies future research needs and highlights innovative control methods, such as biopesticides and pheromone-based trapping systems.

Poland suffered an epidemic of louse-borne typhus from 1916-1923, with 400,000 cases and more than 130,000 deaths. The causative factors were depressed economic conditions and a refugee crisis that engulfed Poland after World War I. The recognition of the epidemic in 1919 stimulated the creation of the League of Red Cross Societies (LRCS). However, the LCRS had limited resources and the Poles requested help from other governments and the League of Nations (LoN). The United States sent the American-Polish Relief Expedition to conduct delousing. However, the Polish-Soviet War of 1920 disrupted typhus control and exacerbated the refugee situation. The LoN belatedly organized an underfunded Epidemic Commission. The LCRS sent a research team that did ground-breaking work on the pathology of typhus. Into 1921, the epidemic continued, driven by refugees from typhus-stricken Russia. By 1924, typhus cases were finally approaching pre-World War I levels. Multiple factors lead to the amelioration of the epidemic. The repatriation of prisoners of war and displaced civilians had concluded by 1923. Also, there had been a steady influx of sanitary, food, economic, and medical aid from various organizations into Poland since 1919. Administratively, within Poland, the anti-typhus campaign was also conducted more effectively by the Extraordinary Epidemic Commissariat.

Medicago sativa L. (Alfalfa) is a globally recognized forage legume that has recently gained attention for its high protein content, making it suitable for both human and animal consumption. However, due to its perennial nature and autotetraploid genetics, conventional plant breeding requires a longer timeframe compared to other crops. Therefore, genetic engineering offers a faster route for trait modification and improvement. Here, we describe a protocol for achieving efficient transient gene expression in alfalfa through genetic transformation with the Agrobacterium tumefaciens pCAMBIA1304 vector. This vector contains the reporter genes β-glucuronidase (GUS) and green fluorescent protein (GFP), along with a selectable hygromycin B phosphotransferase gene, all driven by the CaMV 35s promoter. Various transformation parameters—such as different explant types, leaf ages, leaf sizes, wounding types, bacterial concentrations (OD600nm), tissue preculture periods, incubation periods, co-cultivation periods, and different concentrations of acetosyringone, silver nitrate, and calcium chloride—were optimized using 3-week-old plantlets raised in vitro. Results were attained from data based on the semi-quantitative observation of the percentage and number of GUS spots on different days of agro-infection in alfalfa explants. The highest percentage (76.2%) of GUS-positive alfalfa leaf explants was observed after 3 days of agroinfection at a bacterial concentration of 0.6, 2 days of preculture, 30 min of infection time, 150 µM acetosyringone, 4 mM calcium chloride, and 75 µM silver nitrate. The transient expression of genes of interest was confirmed via histochemical GUS and GFP assays. The results based on transient reporter gene expression suggest that various factors influence T-DNA delivery in the Agrobacterium-mediated transformation of alfalfa.

Ground level ozone is an abiotic stress estimated to reduce mean global annual wheat yields by nearly 10%. This study in solardomes exposed an elite cultivar, and multiple lines of synthetic wheat (primary and F2) to four levels of ozone (30 ppb, 55 ppb, 80 ppb, 110 ppb) for three months, with two lines (cv Paragon and an F2 line, BC1) selected for X-ray microcomputed tomography. The uCT imaging revealed ozone’s effect on individual grain formation, both spatially within the spike and on grain shape. Reductions in grain number occurred primarily across the middle of the spike. Grain volume reductions were driven more by reduced width and depth than reduced length. Based on yield data, both lines demonstrated relative tolerance to ozone. Links between ozone’s effects on grain morphology and grain quality are also explored. These data provide information that could be utilised in wheat breeding programmes to increase tolerance to ozone of this staple food crop.

Cleomella serrulata is a native flowering plant found in North America. Even though this plant is of ecological and native medicinal importance, very little is known about the genomic makeup of Cleomella and the Cleomaceae family at large. Here we report the complete chloroplast genome of Cleomella serrulata and provide an evolutionary comparison to other chloroplast genomes from Cleomaceae and closely related families. This study confirms the taxonomic placement of Cleomella as a distinct genus, but also provides phylogenetic insights that imply potential adaptive strategies and evolutionary mechanisms driving genomic diversity of the Cleomella genus. Whole genome-based and ANI comparisons indicate that the Cleomella species form a distinct clade that is about equidistant from the other Cleomaceae genera as it is from the genera from the nearby Capparaceae and Brassicaceae. This is the first complete chloroplast-based phylogenetic comparison of Cleomella species to other related genera and helps refine the complex taxonomic distinctions of the Cleomaceae.

Understanding the genotype x environment (GE) interaction for traget trait is valuable for growers, agronomists, breeders and the seed industry. The objective of this study was to see and explore the genotype x environment interaction for grain yield of wheat to better guide genotype selection and breeding. The genotype main effect and GE interaction effect (GGE) biplots resolved the following three genotypes: 85 (ETW17-377), 82 (ETW17-374) and 13 (ETW17-281) for being the best yielding and stable. The Kulumsa site planted on 4^th of July 2017 (environment 7=E7) and the DebreZeit site on 20^th of July 2017 (E3) were the most effective environments in distinguishing the test genotypes and are thus suitable environments for future evaluation and selection with specific adaptation. Melkasa site planted on 4^th July (E9) was a representative environment where genotypes can be evaluated for wide adpaptation. The genetic covariate biplot indicated that thousand kernel weight (TKW) and plant height (PH) had significant positive associations with grain yield implying the possible concurrent indirect selection of both traits for exploiting GE interaction for grain yield of wheat.

To date, various chimeric lysins have been developed as efficacious antibiotics against multidrug-resistant bacteria, but direct comparisons of their antibacterial activities have been difficult due to the preparation of multiple recombinant chimeric lysins. Previously, we reported an E. coli cell-free expression method to screen better chimeric lysins against Staphylococcus aureus, but we still needed to increase the amounts of expressed proteins enough to be able to detect them non-isotopically for quantity comparisons. In this study, we improved the previous cell-free expression system by adding a previously reported artificial T7 terminator and reversing the different nucleotides between the T7 promoter and start codon to those of the T7 phage. The new method increased the expressed amount of chimeric lysins enough for us to detect them using Western blotting. Therefore, the qualitative comparison of activity between different chimeric lysins has become possible via the adjustment of the amount variables between samples without protein purification. We applied it to select more active chimeric lysins derived from our previously reported chimeric lysin (ALS2). Finally, we compared the antibacterial activities of our selected chimeric lysins with reported chimeric lysins (ClyC and ClyO) and lysostaphin, and determined the rank orders of antibacterial activities on different S. aureus strains in our experimental conditions.

Background. Azithromycin (AZM) is widely used in cystic fibrosis (CF) treatment following clinical trials demonstrating improved lung function and fewer pulmonary exacerbations. While the precise mechanisms remain elusive, immunomodulatory actions are thought to be involved. We previously reported impaired phagocytosis and defective anti-inflammatory M2 macrophage polarization in CF macrophages. This study systematically analyzed the effect of AZM on the functions of unpolarized and M1/M2 polarized macrophages in CF. Methods: Monocytes, isolated from the venous blood of patients with CF (pwCF) and healthy controls (HCs) were differentiated into monocyte-derived macrophages (MDMs) and infected with P. aeruginosa. P. aeruginosa uptake and killing by MDMs in the presence or absence of AZM was studied. M1 and M2 macrophage polarizations were induced and their functions and cytokine release were analyzed. Results: Following AZM treatment, both HC and CF MDMs exhibited a significant increase in P. aeruginosa uptake and killing, however, lysosomal acidification remained unchanged. AZM treatment led to higher activation of ERK1/2 in both HC and CF MDMs. Pharmacological inhibition of ERK1/2 using U0126 significantly reduced P. aeruginosa uptake in HC MDMs. M1 macrophage polarization remained unaffected, however, AZM treatment led to increased IL-6 and IL-10 release in both HC and CF M1 macrophages. AZM also significantly increased the phagocytic index for both pHrodo E. coli and S. aureus in CF M1 macrophages. In CF, AZM treatment promoted anti-inflammatory M2 macrophage polarization, with an increased percentage of CD209+ M2 macrophages, induction of the M2 gene CCL18, along with its secretion in the culture supernatant. However, AZM did not restore endocytosis in CF, another essential feature of M2 macrophages. Conclusions: This study highlights the cellular functions and molecular targets of AZM which may involve improved uptake of both gram-positive and gram-negative bacteria, restored anti-inflammatory macrophage polarization in CF. This may in turn shape the reduced lung inflammation observed in clinical trials. In addition, we confirmed the role of ERK1/2 activation for bacterial uptake.

Brain-stimulation reward, also known as intracranial self-stimulation (ICSS), is a commonly used procedure for studying brain reward function and drug reward. In electrical ICSS, an electrode is surgically implanted into the medial forebrain bundle in the lateral hypothalamus or the ventral tegmental area in the midbrain. Operant lever responding leads to the delivery of electrical pulse stimulation. The alteration in the stimulation frequency-lever response curve is used to evaluate the impact of pharmacological agents on brain reward function. If a test drug induces a leftward or upward shift in the ICSS response curve, it implies a reward-enhancing or abuse-like effect. Conversely, if a drug causes a rightward or downward shift in the functional response curve, it suggests a reward-attenuating or aversive effect. A significant drawback of electrical ICSS is the lack of cellular selectivity in understanding the neural substrates underlying drug reward versus aversion. Excitingly, recent advancements in optical ICSS (oICSS) have facilitated the development of at least three cell type-specific oICSS models – dopamine-, glutamate-, and GABA-dependent oICSS. In these new models, a comparable frequency-rate response curve has been established and employed to study the substrate-specific mechanisms underlying brain reward function and a drug's rewarding versus aversive effects. In this review article, we summarize recent progress in this exciting research area. The findings in these new behavioral models have not only increased our understanding of the neural mechanisms underlying drug reward and addiction but have also introduced a novel experimental approach in preclinical medication development for treating substance use disorders.

Soil water balance (SWB) in woody crops is sometimes difficult to estimate with one-dimensional models because these crops do not completely cover the soil and usually have a deep root system, particularly when cropped under rainfed conditions in a Mediterranean climate. In this study, the actual crop evapotranspiration (ETc act) is estimated with the soil water balance model SIMDualKc which uses the dual-Kc approach (relating the fraction of soil cover with the crop coefficients) to improve the estimation of the water requirements of a rainfed vineyard, using data from a deep soil profile. The actual basal crop coefficient (Kcb act) obtained using the SIMDualKc model was compared with the Kcb act estimated using the A&amp;P approach, which is a simplified approach based on measurements of the fraction of ground cover and crop height. Spectral vegetation indices derived from Landsat-5 satellite data were used to determine the fraction of ground cover (fc VI) and thus, the density coefficient (Kd). The SIMDualKc model was calibrated using soil water content (SWC) measurements down to a depth of 1.85 meters, which significantly improved the conditions for using a SWB estimation model. The test of the model was performed using a different SWC dataset. A good agreement between simulated and field measured SWC was observed for both data sets along the crop season, with RMSE&lt;12.0 mm, NRMSE &lt;13%. The calibrated Kcb values were 0.15, 0.60 and 0.52 for the initial, mid-season, and end season, respectively. The ratio between actual (ETc act) and crop evapotranspiration (ETc) was quite low between veraison and maturity (mid-season), corresponding to 36%, indicating that the rainfall was not sufficient to satisfy the vineyards water requirements. Spectral vegetation indices used to compute fc VI were unable to fully track the plants’ conditions when water stress. However, ingestion of data from remote sensing showed promising results that could be used to support decisions making in irrigation scheduling. Further studies on the use of the A&amp;P approach using remote sensing data are required.

A major advance of drug discovery and targeted therapy directed to cancer cells may be achieved by exploitation and immunomodulation of their unique biological property. This re-view summarizes our efforts to develop novel chemo-thermo-immuno-therapy (CTI therapy) by conjugating a melanogenesis substrate, N-propionyl cysteaminylphenol (NPrCAP: amine analog of tyrosine), with magnetite nanoparticles (MNP). In our approach, NPrCAP provides a unique drug delivery system (DDS) because of its selective incorporation into melanoma cells. It also functions as a melanoma-targeted therapeutic drug because of its production of highly reactive free radicals (melanoma-targeted chemotherapy). Moreover, utilization of MNP is a platform to develop thermo-immunotherapy because of heat shock protein (HSP) generation upon exposure to an alternating magnetic field (AMF). The feasibility of our approach was successfully shown in experimental in vivo and in vitro mouse melanoma models and in preliminary clinical trials to a limited number of advanced melanoma patients.

Recently, Shehata et al. [37] introduced the r+1Rs(B;C; z) matrix function and established some properties. The aim of this study established to devote and derive certain basic properties including analytic properties, recurrence matrix relations, dierential properties, new integral representations, k- Beta transform, Laplace transform, fractional k-Fourier transform, fractional integral properties, the k-Riemann{Liouville and k-Weyl fractional integral and derivative operators an extended version of r+1Rs;k matrix function. We establish its relationships with other well known special matrix functions which have some particular cases in the context of three parametric Mittag-Leer matrix function, k- Konhauser and k-Laguerre matrix polynomials. Finally, some special cases of the established formulas are also discussed.

Rift Valley fever (RVF) is a mosquito-borne zoonotic viral disease that infects both human and animals. This is a descriptive study summarizes investigation and response to RVF outbreak, using surveillance data. A RVF outbreak occurred in Berber locality in northern Sudan. We identified 246 cases of RVF including seven deaths among humans, 119 deaths and 82 abortions among Livestock. Our entomological surveillance confirmed the presence of Anopheles arabiensis, An. stephensi, Aedes aegypti, Ae. vexans, Culex pipiens, Cx. Quinquefasciatus, and Cx. theileri in the area during the outbreak. In a comparison with another outbreak of Rift Valley fever in nearby area while ago, a multisectoral One Health response strategy has resulted in strengthening the health system through re-innovating health facilities and centres and training about 200 healthcare and emergency responders. Additionally, it reduced cases and fatalities among humans by 78% and 63%, respectively, and loss in livestock due to deaths and/or abortions by 82%. The added-value of implementing One Health strategy was saving more lives and resources, while strengthening the health system. We recommend the systematic institutionalization of One Health strategy in the country as a core part of the national prevention and control strategy for zoonotic diseases epidemics and pandemics.

Sarcopenia is associated with clinical complications, which increase mortality. Effective sarcopenia risk screening in the elderly should be grounded in a comprehensive assessment, encompassing both nutritional status and medication use. Current screening tools, while emphasizing muscular per-formance, exhibit limited sensitivity in identifying elderly individuals at risk of sarcopenia. This cross-sectional study aimed to develop a sarcopenia risk screening tool, named Sarc-Global, with enhanced sensitivity, incorporating factors pertinent to the overall health of the elderly. Utilizing the criteria established by EWGSOP2 for diagnosing sarcopenia, we evaluated 395 communi-ty-dwelling elderly individuals. This evaluation served as a reference for assessing the efficacy of two validated questionnaires, Sarc-F and Sarc-CalF, and our newly developed Sarc-Global. Con-structed through multiple logistic regression, Sarc-Global integrates variables such as sex, age, medication use, body mass index, arm circumference, and handgrip strength – all significantly associated with sarcopenia (p

The Polyurethane (PU) mixture is a high−performance engineering material with different dynamic properties compared to a hot−mixed asphalt mixture (HMA). This paper analyzed whether the Kramers−Kronig (K−K) relation and thermo−rheological simple properties were applicable to the PU mixture. Based on the result discussion, the PU mixture exhibited thermo−rheological simple properties within the test conditions. The time−temperature superposition principle (TTSP) was applicable for the PU mixture to construct the dynamic modulus master curve using the standard logistic Sigmoidal (SLS) model, the generalized logistic sigmoidal (GLS) model, and the Havriliak−Negami (HN) model. The Hilbert integral transformed SLS and GLS models for the phase angle can accurately fit the measured phase angle data with newly fitted shift factors and predict the phase angle within the viscoelastic range. The Core−Core and black space diagrams both displayed single continuous smooth curves, which can be utilized to characterize the viscoelastic property of the PU mixture. The K−K relation is applicable for the PU mixture to obtain the phase angle master curve model, storage modulus, and loss modulus from the complex modulus test results. The phase angle of the PU mixture cannot be derived from the dynamic modulus data and currently needs to be derived from the laboratory measurement.

innate and adaptive immune responses lead to wound healing by regulating a complex series of events promoting cellular cross-talk. An inflammatory response is presented with its characteristic clinical symptoms: heat, pain, redness, and swelling. Some smart thermo-responsive polymers like chitosan can be used to create biocompatible and biodegradable scaffolds with 3D architectures similar to human structures, allowing their efficient and safe use as tissue engineering and drug delivery systems in chronic wounds. Locally heated tumors above polymer lower critical solution temperature can induce its conversion into a hydrophobic form, enhancing drug release until the thermal stimulus is gone, where a lower release is due to the swelling of the material. This paper integrates the relevant reported contributions of bioengineered scaffolds for thermo-responsive drug delivery in wound healing. Therefore, we present a comprehensive review that aims to demonstrate the capacity of these systems to provide spatially and temporally controlled release strategies for one or more drugs used in wound healing. In this sense, the novel manufacturing techniques of 3D-printing and electrospinning are explored for the tuning of their physicochemical properties to adjust therapies according to the patient’s convenience, as well as reduce drug toxicity and side effects.

There are laws and rights aimed at people with disabilities, especially those with Mild Intellectual Disability (LDD), who actively participate in society but face barriers in learning and participating in various activities. In Colombia, where 1.3 million people with disabilities are registered, 16.8% correspond to the category of DIL, some of whom are part of the economically active population. Despite this, significant employment gaps persist.In order to address this gap, this research focuses on the analysis of the specific problems related to the labor inclusion of people with IDL in logistics environments, particularly in cold rooms. The aim is to prevent occupational hazards through the application of Industry 4.0 technologies.Through the collaboration of the Analytics and Design Research Seedbed, with entrepreneurs and experts in the field, significant challenges in labor inclusion in low-temperature environments were identified. The agile Scrum methodology was used to develop a prototype of an application that addresses these issues. This prototype meets the functional and non-functional requirements necessary to ensure the protection and prevention of risks for workers with DIL who perform functions in refrigerated rooms.This prototype manages to provide an inclusive alternative for people with disability Intellectual Light, challenging business cultural paradigms, by integrating mobile devices with Industry 4.0 technologies, encouraging greater interaction between machines and human beings, thus prioritizing the health and safety of employees in their daily activities.

Transitions from seed to seedling represent a critical developmental step in the life cycle of higher plants, dramatically affecting plant ontogenesis and stress tolerance. The release from dormancy to acquiring the germination ability is defined by a balance of phytohormones, with a substantial contribution of abscisic acid (ABA), which inhibits germination. We studied the embryonic axes of Pisum sativum L. before and after radicle protrusion. Our previous work compared RNA sequencing-based transcriptomics in the embryonic axes isolated before and after radicle protrusion. The current study aims to analyze ABA-dependent gene regulation during the transition of embryonic axes from germination to post-germination stage. First, we determined the levels of abscisates (ABA, phaseic acid, dihydrophaseic acid, and neo-phaseic acid) using the ultra-high-performance liquid chromatography-tandem mass spectrometry. Second, we made a detailed annotation of ABA-associated genes using RNA sequencing-based transcriptome profiling. Finally, we analyzed the DNA methylation pattern in the promoters of the PsABI3, PsABI4, and PsABI5 genes. We showed that changes in the abscisate profile are characterized by the accumulation of ABA catabolites, and the ABA-related gene profile is accompanied by the upregulation of genes controlling the seedling development and the downregulation of genes controlling the water deprivation. The expression of ABI3, ABI4 and ABI5, which encode the crucial transcription factors during late maturation, was downregulated by more than 20-fold, and their promoters exhibited a high level of methylation already at the late germination stage. Thus, although ABA remains important, other regulators seems to be involved in the transition from seed to seedling.

In the face of climate change, bringing more useful alleles and genes from wild relatives of wheat is crucial to develop climate-resilience varieties. We used two populations of backcrossed recombinant inbred lines (BIL1 and BIL2), developed using two intra-specifically diverse Aegilops tauschii accessions from lineage 1 and lineage 2, respectively, and backcrossing to common wheat cultivar ‘Norin 61’. The study aimed to identify quantitative trait loci (QTL) associated with heat stress (HS) tolerance. The two BILs were evaluated under heat stress environments in Sudan for phenology, plant height (PH), grain yield (GY), biomass (BIO), harvest index (HI), and thousand kernel weight (TKW). Grain yield was significantly correlated with BIO and TKW under HS; therefore, stress tolerance index (STI) was calculated for these traits as well as for GY. A total of 16 heat tolerant lines were identified based on GY and STI-GY. The QTL analysis performed using inclusive composite interval mapping identified a total of 40 QTLs in BIL1 and 153 QTLs in BIL2 across all environments. We detected 39 QTLs associated with GY-STI, BIO-STI, and TKW-STI in both populations (14 in BIL1 and 25 in BIL2). The QTL associated with STI were detected on chromosomes 1A, 3A, 5A, 2B, 4B, and all the D-subgenomes. We found that QTL detected only under HS for GY on chromosome 5A, TKW on 3B and 5B, PH on 3B and 4B, and grain filling duration on 2B. The higher number of QTLs identified in BIL2 for heat stress tolerance suggests the importance of assessing the effects of intraspecific variation of Ae. tauschii in wheat breeding as it could modulate the heat stress responses/adaptation. Our study provides useful genetic resources for uncovering heat-tolerant QTLs for wheat improvement for heat stress environments.

Optical microcombs represent a new paradigm for generating laser frequency combs based on compact chip-scale devices, which have underpinned many modern technological advances for both fundamental science and industrial applications. Along with the surge in activity related to optical micro-combs in the past decade, their applications have also experienced rapid progress ‒ not only in traditional fields such as frequency synthesis, signal processing, and optical communications, but also in new interdisciplinary fields spanning the frontiers of light detection and ranging (LiDAR), astronomical detection, neuromorphic computing, and quantum optics. This paper reviews the applications of optical microcombs. First, an overview of the devices and methods for generating optical microcombs is provided, which are categorized into material platforms, device architectures, soliton classes, and driving mechanisms. Second, the broad applications of optical microcombs are systematically reviewed, which are categorized into microwave photonics, optical communications, precision measurements, neuromorphic computing, and quantum optics. Finally, the current challenges and future perspectives are discussed.

We report enhanced nonlinear optics in complementary metal-oxide-semiconductor (CMOS) compatible photonic platforms through the use of layered two-dimensional (2D) graphene oxide (GO) films. We integrate GO films with silicon-on-insulator nanowires (SOI), high index doped silica glass (Hydex) and silicon nitride (SiN) waveguides and ring resonators, to demonstrate an enhanced optical nonlinearity including Kerr nonlinearity and four-wave mixing (FWM). The GO films are integrated using a large-area, transfer-free, layer-by-layer method while the film placement and size are controlled by photolithography. In SOI nanowires we observe a dramatic enhancement in both the Kerr nonlinearity and nonlinear figure of merit (FOM) due to the highly nonlinear GO films. Self-phase modulation (SPM) measurements show significant spectral broadening enhancement for SOI nanowires coated with patterned films of GO. The dependence of GO’s Kerr nonlinearity on layer number and pulse energy shows trends of the layered GO films from 2D to quasi bulk-like behavior. The nonlinear parameter of GO coated SOI nanowires is increased 16 folds, with the nonlinear FOM increasing over 20 times to FOM > 5. We also observe an improved FWM efficiency in SiN waveguides integrated with 2D layered GO films. FWM measurements for samples with different numbers of GO layers and at different pump powers are performed, achieving up to ≈7.3 dB conversion efficiency (CE) enhancement for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. These results reveal the strong potential of GO films to improve the nonlinear optics of silicon, Hydex and SiN photonic devices.

Optical biopsy describes a range of medical procedures in which light is used to investigate disease in the body, often in hard-to-reach regions via optical fibres. Optical biopsies can reveal a multitude of diagnostic information to aid therapeutic diagnosis and treatment with higher specificity and shorter delay than traditional surgical techniques. One specific type of optical biopsy relies on Raman spectroscopy to differentiate tissue types at the molecular level and has been used successfully to stage cancer. However, complex micro-optical systems are usually needed at the distal-end to optimise the signal-to-noise properties of the Raman signal collected. Manufacturing these devices remains a critical challenge, particularly in a way suitable for large scale adoption. In this paper, we describe a novel fibre-fed micro-optic system designed for efficient signal delivery and collection during a Raman spectroscopy based optical biopsy. Crucially, we fabricate the device using a direct-laser-writing technique known as ultrafast laser assisted etching which is scalable and allows components to be aligned passively. The Raman probe has a sub-millimetre diameter and offers confocal signal collection with 71.3 ± 1.5% collection efficiency over a 0.8 numerical aperture. Proof of concept spectral measurements were performed on mouse intestinal tissue and compared with results obtained using a commercial Raman microscope.

The bulk backscattering ratio ($\tilde{b_{bp}}$) is commonly used as a descriptor of the bulk real refractive index of the particulate assemblage in natural waters. Based on numerical simulations, we analyze the impact of heterogeneity of phytoplankton cells on $\tilde{b_{bp}}$. $\tilde{b_{bp}}$ is modeled considering viruses, heterotrophic bacteria, phytoplankton, detritus, and minerals. Three study cases are defined according to the relative abundance of these different components. Two study cases represent typical situations in open ocean, outside (No-B/No-M) and inside bloom (B/No-M). The third study case is typical of coastal waters with the presence of minerals. Phytoplankton cells are modeled by a two-layered spherical geometry representing a chloroplast surrounding the cytoplasm. The $\tilde{b_{bp}}$ values are higher when heterogeneity is considered because the contribution of coated spheres to backscattering is higher than homogeneous spheres. The impact of heterogeneity is however strongly conditioned by the hyperbolic slope $\xi$ of the particle size distribution. Even if the relative concentration of phytoplankton is small (<1%), $\tilde{b_{bp}}$ increases by about 60% (for $\xi=4.3$ and for the No-B/No-M water body), when the heterogeneity is taken into account, in comparison with a particulate population only composed by homogeneous spheres. As expected, heterogeneity has a much smaller impact (about 5$\%$ for $\xi=4.3$) on $\tilde{b_{bp}}$ when minerals are added.

Dyadic data which is also called co-occurrence data (COD) contains co-occurrences of objects. Searching for statistical models to represent dyadic data is necessary. Fortunately, finite mixture model is a solid statistical model to learn and make inference on dyadic data because mixture model is built smoothly and reliably by expectation maximization (EM) algorithm which is suitable to inherent spareness of dyadic data. This research summarizes mixture models for dyadic data. When each co-occurrence in dyadic data is associated with a value, there are many unaccomplished values because a lot of co-occurrences are inexistent. In this research, these unaccomplished values are estimated as mean (expectation) of random variable given partial probabilistic distributions inside dyadic mixture model.

This article presents a concise survey of basic discrete and semi-discrete nonlinear models which produce two- and three-dimensional (2D and 3D) solitons, and a summary of main theoretical and experimental results obtained for such solitons. The models are based on the discrete nonlinear Schrödinger (DNLS) equations and their generalizations, such as a system of discrete Gross-Pitaevskii (GP) equations with the Lee-Huang-Yang corrections, the 2D Salerno model (SM), DNLS equations with long-range dipole-dipole and quadrupole-quadrupole interactions, a system of coupled discrete equations for the second-harmonic generation with the quadratic (χ⁽²⁾) nonlinearity, a 2D DNLS equation with a superlattice modulation opening mini-gaps, a discretized NLS equation with rotation, a DNLS coupler and its PT-symmetric version, a system of DNLS equations for the spin-orbit-coupled (SOC) binary Bose-Einstein condensate, and others. The article presents a review of basic species of multidimensional discrete modes, including fundamental and vortex solitons, their bound states, gap solitons populating mini-gaps, symmetric and asymmetric solitons in the conservative and PT-symmetric couplers, cuspons in the 2D SM, discrete SOC solitons of the semi-vortex and mixed-mode types, 3D discrete skyrmions, and some others.

Hox gene clusters are crucial in Embryogenesis. It was observed that some Hox genes are located in order along the telomeric to centromeric direction of the DNA sequence: Hox1, Hox2, Hox3…. These genes are expressed in the same order in the ontogenetic units of the Drosophila embryo along the Anterior-Posterior axis. The two entities (genome and embryo) differ significantly in linear size and in-between distance. This strange phenomenon was named Spatial Collinearity (SP). Later, it was observed that, particularly in the Vertebrates, a Temporal Collinearity (TC) coexists: first is Hox1 expressed, later Hox2 and even later Hox3,…,. According to a Biophysical Model (BM), pulling forces act at the anterior end of the cluster while a cluster fastening applies at the posterior end. Hox clusters are irreversibly elongated along the force direction. During Evolution, the elongated Hox clusters are broken at variable lengths thus split clusters may be created. An Empirical Rule was formulated distinguishing development due to a complete Hox cluster from development due to split Hox clusters. BM can ‘explain’ this Empirical Rule. In a spontaneous mutation where the cluster fastening is dismantled, a minimal pulling force can automatically shift the cluster inside the Hox activation domain. This cluster translocation can probably explain the absence of Temporal Collinearity in Drosophila.

The World Health Organization recently proposed the Tricycle Protocol for harmonized surveillance of extended-spectrum beta lactamase-producing E. coli (ESBL-Ec) as a proxy for AMR among humans, animals, and the environment. We implemented the Tricycle Protocol with ceftriaxone (CRO) to screen for ESBL-Ec using membrane filtration (TBX-CRO) and Colilert Quanti-Tray (CQT-CRO) workflows in parallel applied to water samples collected from four lakes. ESBL-Ec and E. coli abundance and prevalence, and ESBL-Ec to E. coli ratios were significantly higher in the two highly impacted lakes (receiving sewage treatment plant effluent, open defecation site adjacent to informal settlements) compared to less impacted lakes (wildlife sanctuary, recreational site). The cumulative burden of antibiotic compounds was also higher in the highly impacted lakes. Even in the “pristine” lake in a bird sanctuary, ESBL-Ec and an antibiotic compound were present. Overall, the CQT-CRO format yielded reasonable qualitative (K = 0.603) and quantitative agreement (intra-class correlation coefficient = 0.849) and linearity (r² = 0.785) with the TBX-CRO format adapted from the Tricycle Protocol. However, CQT-CRO doubled the prevalence of ESBL-Ec in settings with decreased E. coli abundance. Consistent with observations for other third-generation cephalosporins, CRO performed poorly for screening the ESBL phenotype. Further, confirmed ESBL-Ec isolates were not associated with an increased number of resistance phenotypes compared with non-ESBL isolates. Instead, the number of resistance phenotypes was associated with the lake from which the sample was collected. In high-burden settings, AMR surveillance efficiency could be increased by directly testing generic E. coli isolates for ESBL phenotype and antibiotic susceptibility. Our experience also suggests that sequencing ESBL-Ec will likely be required to determine epidemiologically appropriate risk mitigation strategies where ESBL-Ec are prevalent. Resource limitations could jeopardize the relevance of the Tricycle Protocol for changing the trajectory of AMR in high-burden low-resource settings globally.

To delve into the structure-function relationship of transmembrane proteins (TMPs), robust protocols are needed to produce them in a pure, stable, and functional state. Among all hosts that express heterologous TMPs, E. coli has the lowest cost and fastest turnover. However, many of the expressed in E. coli TMPs are misfolded. Several strategies have been developed to either direct the foreign TMPs to E. coli’s membrane or retain them in a cytosolic soluble form to overcome this deficiency. Here, we summarize protein engineering methods to produce chimera constructs of the desired TMPs fused to either signal peptide or precursor maltose binding protein (pMBP) to direct the entire construct to the periplasm, therefore depositing the fused TMP in the plasma membrane. We further describe strategies to produce TMPs in soluble form by utilizing N-terminally fused MBP without signal peptide. Depending on its N- or C-terminus location, a fusion to apolipoprotein A-I can either direct the TMP to the membrane or shield the hydrophobic regions of the TMP, maintaining the soluble form. Strategies to produce G-protein coupled receptors, TMPs of Mycobacterium tuberculosis, HIV-1 Vpu, and other TMPs are discussed. This knowledge could increase the scope of TMPs’ expression in E. coli.

The spatial and temporal variability in dietary preferences of juvenile three-spined stickleback Gasterosteus aculeatus, was studied across typical coastal habitats of Keret Archipelago, Kandalaksha Bay, the White Sea. Sampling of fish using beach seine was implemented in late July-early August and in late August, and zooplankton samples were collected to make a quantitative evaluation of abundance of potential prey items. Similarity Percentage (SIMPER) analysis implemented over the data obtained from stomach content analysis revealed five planktonic taxa mostly contributing to the diet of juvenile sticklebacks, of which copepod Temora longicornis was the most important prey item at marine sites, while Acartia longiremis prevailed in diet of fishes in marine lagoon. Calculation of selectivity index demonstrated that some taxa (e.g., A. longiremis) were always avoided by juvenile fishes, others (e.g. Microsetella norvegica) were firstly avoided and then selected in late August. Calculation of selectivity index was implemented per sample and per individual fish indicated that taxa like T. longicornis and were selected during the whole period of study, fishes demonstrated pronounced individual variation in prey selectivity. In general, data on selectivity indicated that despite juvenile sticklebacks feed on mostly available prey items, they can demonstrate taxonomic and size-specific prey selectivity.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

Gas bubbles present in liquids underpin many natural phenomena and human-developed technologies that improve the quality of life. Since all living organisms are predominantly made of water, they may also contain gas bubbles—introduced both naturally and artificially—that can serve as biomechanical sensors operating in hard-to-reach places inside a living body and emitting signals that can be detected by common equipment used in ultrasound and photoacoustic imaging procedures. This kind of biosensors is the focus of the present article, where we critically review the emergent sensing technologies based on acoustically driven oscillations of gas bubbles in liquids and bodily fluids. This review is intended for a broad biosensing community and transdisciplinary researchers translating novel ideas from theory to experiment and then to practice. To this end, all discussions in this review are written in a language that is accessible to non-experts in specific fields of acoustics, fluid dynamics and acousto-optics.

The addition of biocarriers can improve the biological processes appearing in a bioreactor since their surface allows the immobilization, attachment, protection, and growth of microorganisms. In addition, the development of a biofilm layer allows the colonization of microorganisms in the biocarriers. The structure, composition, and roughness of the biocarriers' surface are crucial factors that affect the development of the biofilm. In the current work, the aluminosilicate zeolites 13X and ZSM-5 were examined as the main building components of the biocarrier scaffolds, using bentonite, montmorillonite, and halloysite nanotubes as inorganic binders in various combinations. 3D printing was utilized to form pastes into monoliths that underwent heat treatment. The 3d-printed biocarriers were subjected to a mechanical analysis, including density, compression, and nanoindentation tests. Furthermore, the 3d-printed biocarriers were morphologically and structurally characterized using nitrogen adsorption at 77 K (LN2), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The stress-strain response of the materials being studied was obtained through nanoindentation tests combined with finite element analysis (FEA). These tests were also utilized to simulate the lattice geometries under compression loading conditions to investigate their deformation and stress distribution in relation to experimental compression testing. The results indicated that the 3d-printed biocarrier 13X/halloysite nanotubes was endowed with high specific surface area and extended mesoporous structure. Due to these assets, its bulk density was one of the lowest observed amongst the biocarriers derived from the various combinations of materials. The biocarriers based on the 13X zeolite exhibited the highest mechanical stability and appropriate morphological features. The 13X/halloysite nanotubes scaffold exhibits a moderate hardness value compared to the rest, while it presents the highest value of modulus of elasticity. In conclusion, Aluminosilicate zeolites and their combination with clays and inorganic nanotubes afford 3d-printed biocarriers of various textural and structural properties, which can be utilized to improve biological processes.

Marine sponges, a well documented prolific source of natural products, harbors numerous microbial communities believed to possess N-acyl homoserine lactones (AHLs) mediated Quorum sensing (QS) as one of the mechanisms of interaction. Bacteria and eukaryotic organisms are known to produce molecules that can interfere with QS signaling, thus affecting microbial genetic regulation and function. In the present study, we established the potential for production of both QS signal molecules as well as QS interfering molecules (QSI) in the same sponge species Sarcotragus spinosulus. A total of eighteen saturated acyl chain AHLs were identified along with six putative unsaturated acyl chain AHLs. Bioassay guided purification led to the isolation of two brominated metabolites with QS-interfering activity. The structures of these compounds were elucidated by comparative spectral analysis of 1HNMR and HR-MS data and was identified as 3-Br-N-methyltyramine (1) and 5,6-dibromo-N,N-dimethyltryptamine (2). The QSI activity of compounds 1 and 2 were evaluated using reporter gene assays for long- and short-chain signals (E. coli pSB1075 and E. coli pSB401) and was confirmed by measuring dose dependent inhibition of proteolytic activity and pyocyanin production in P. aeruginosa PAO1. The obtained results showed the co-existence of QS and QSI in S. spinosulus, a complex network which may mediate the orchestrated function of the microbiome within the sponge holobiont.

CubeSats, known for their compact size and cost-effectiveness, have gained significant popularity. However, their limited size imposes restrictions on optical aperture and, consequently, Ground Resolution Distance in Earth Observation missions. To overcome this limitation, the concept of deployable optical payloads with segmented primary mirrors which can unfold like petals has emerged, enabling larger synthetic apertures and enhanced spatial resolution. This study explores the potential benefits of leveraging Additive Manufacturing (AM) and Topology Optimization (TO) in the realm of ultra-precision machining, specifically single point diamond machining. The goal is to reduce fixture weight while improving stiffness to minimize deformations caused by rotational and cutting forces which compromise optical performance. Through Finite Element Analysis, this research compares conventionally machined fixtures with those produced using AM and TO techniques. The results reveal that concept designs created through TO can achieve a remarkable 68% reduction in weight. This reduction makes the assembly, including the machining fixture and 12U deployable segments, manageable by a single operator without the need for specialized lifting equipment. Moreover, these innovative designs lead to substantial reductions of up to 86% and 51% in deformation induced by rotational and cutting forces, respectively.

: The article presents a brief review of cooling systems of various temperature levels (from 0.1 K to 230 K) for radio astronomical receivers of photonics and electronics. The features of various levels of cooling and the requirements for the design of the cooling system are considered in detail, as well as approaches to designing interfaces for cooled receivers: vacuum, cryogenic, electrical, mechanical, optical, and others required for the effective operation of the receiver,. The presented approaches to design are illustrated by a series of joint developments of the authors carried out over the past 45 years, including those produced last year.

Higher-order topological insulators (HOTIs) are recently discovered topological phases, possessing symmetry-protected corner states with fractional charges. An unexpected connection between these states and the seemingly unrelated phenomenon of bound states in the continuum (BICs) was recently unveiled. When nonlinearity is added to a HOTI system, a number of fundamentally important questions arise. For example, how does nonlinearity couple higher-order topological BICs with the rest of the system, including continuum states? In fact, thus far BICs in nonlinear HOTIs have remained unexplored. Here, we unveil the interplay of nonlinearity, higher-order topology, and BICs in a photonic platform. We observe topological corner states which are also BICs in a laser-written second-order topological lattice, and further demonstrate their nonlinear coupling with edge (but not bulk) modes under the proper action of both self-focusing and defocusing nonlinearities. Theoretically, we calculate the eigenvalue spectrum and analog of the Zak phase in the nonlinear regime, illustrating that a topological BIC can be actively tuned by nonlinearity in such an HOTI. Our studies are applicable to other nonlinear HOTI systems, with promising applications in emerging topology-driven devices.

Layered two-dimensional (2D) graphene oxide (GO) films are integrated with micro-ring resonators (MRRs) to experimentally demonstrate enhanced nonlinear optics in the form of four-wave mixing (FWM). Both uniformly coated and patterned GO films are integrated on CMOS-compatible doped silica MRRs using a large-area, transfer-free, layer-by-layer GO coating method together with photolithography and lift-off processes, yielding precise control of the film thickness, placement, and coating length. The high Kerr nonlinearity and low loss of the GO films combined with the strong light-matter interaction within the MRRs results in a significant improvement in the FWM efficiency in the hybrid MRRs. Detailed FWM measurements are performed at different pump powers and resonant wavelengths for the uniformly coated MRRs with 1−5 layers of GO as well as the patterned devices with 10−50 layers of GO. The experimental results show good agreement with theory, achieving up to ~7.6-dB enhancement in the FWM conversion efficiency (CE) for an MRR uniformly coated with 1 layer of GO and ~10.3-dB for a patterned device with 50 layers of GO. By fitting the measured CE as a function of pump power for devices with different numbers of GO layers, we also extract the dependence of GO’s third-order nonlinearity on layer number and pump power, revealing interesting physical insights about the evolution of the layered GO films from 2D monolayers to quasi bulk-like behavior. These results confirm the high nonlinear optical performance of integrated photonic resonators incorporated with 2D layered GO films.

For gravitational wave (GW) detected neutron star mergers, one of the leading candidates for electromagnetic (EM) counterparts is the afterglow from an ultra-relativistic jet. Where this afterglow is observed, it will likely be viewed off-axis, such as the afterglow following GW170817/GRB 170817A. The temporal behaviour of an off-axis observed GRB afterglow can be used to reveal the lateral jet structure, and statistical model fits can put constraints on the various model free-parameters. Amongst these parameters is the inclination of the system to the line of sight. Along with the GW detection, the afterglow modelling provides the best constraint on the inclination to the line-of-sight and can improve the estimates of cosmological parameters e.g. the Hubble constant, from GW-EM events. However, modelling of the afterglow depends on the assumed jet structure and, often overlooked, the effects of lateral spreading. Here we show how the inclusion of lateral spreading in the afterglow models can affect the estimated inclination of GW-EM events.

Very disparate types of cell populations exhibit similar transcription specificity for certain genes. We identified 20 genes that were expressed preferentially in myoblasts and cerebellum (Myob/Cbl genes) and examined their cell/tissue-specific epigenetics using a combined approach of comparing DNA methylation, chromatin accessibility, and RNA expression in many different cell populations. Some Myob/Cbl genes shared DNA hypo- or hypermethylated regions in myoblasts and cerebellum. Particularly striking was ZNF556, whose promoter is hypomethylated in expressing cells but highly methylated in the many cell populations that do not express the gene. In reporter gene assays, we demonstrated that its promoter’s activity is methylation-sensitive. The atypical epigenetics of ZNF556 may have originated from its promoter’s hypomethylation and selective activation in sperm progenitors and oocytes. Five of the Myob/Cbl genes (KCNJ12, ST8SIA5, ZIC1, VAX2, and EN2) have much higher RNA levels in cerebellum than in myoblasts and displayed myoblast-specific hypermethylation upstream and/or downstream of their promoters that may downmodulate expression. Differential DNA methylation was associated with alternative promoter usage for Myob/Cbl genes MCF2L, DOK7, CNPY1, and ANK1. Myob/Cbl genes PAX3, LBX1, ZNF556, ZIC1, EN2, and VAX2 encode sequence-specific transcription factors, which likely help drive the myoblast and cerebellum specificity of other Myob/Cbl genes. Our study extends our understanding of epigenetic/transcription associations related to differentiation and may help elucidate relationships between epigenetic signatures and muscular dystrophies or cerebellar-linked neuropathologies.

Bamboo is considered a sustainable construction material due to its ability to grow quickly and its mechanical properties that are comparable to timber. Contributing to the current effort to establish the structural bamboo standards in the National Structural Code of the Philippines (NSCP), this study establishes the characteristic compressive strength of four bamboo species: Bambusa vulgaris (36 samples), Dendrocalamus asper (36 samples), Bambusa blumeana (94 samples), and Guadua angustifolia Kunth (30 samples). The samples were subjected to compressive loading following ISO 22157-1 (2017). The characteristic compressive strength values obtained, according to ISO 12122-1 (2014), were 40.35 MPa for B. vulgaris, 40.21 MPa for D. asper, 46.63 MPa for B. blumeana, and 36.99 MPa for G. angustifolia Kunth. Simple linear analysis, One-way ANOVA, and Welch’s t-Test were used to analyze the correlation models and establish a comparative analysis of the effect of nodes, and geometric and physical properties on the compressive strength of bamboos. Comparing the characteristic compressive strength obtained from this study to the strength of unseasoned structural timber of Philippine woods, all bamboo species showed higher strength values, and thus have great potential as an alternative construction material to timber.

Pseudomonas aeruginosa is an opportunistic pathogen that poses a significant threat to individuals with chronic respiratory ailments, such as cystic fibrosis (CF). The pathogen is highly prevalent in CF individuals and is responsible for chronic infection, resulting in severe tissue damage and poor patient outcome. However, early detection and immediate treatment are critical to prevent bacterial persistence and establishment of chronic infection. Presently, antibiotics including aminoglycosides, beta-lactams, polymyxins, and fluoroquinolones along with anti-inflammatory medications are being used to treat P. aeruginosa infections in CF patients. However, prolonged antibiotic administration has led to the emergence of widespread multidrug resistance in P. aeruginosa (CF isolates), contributing to antimicrobial resistance (AMR) and failure of antimicrobial therapies. Thus, exploring viable alternatives such as antivirulence therapeutics can be vital towards managing pseudomonal infections in CF patients and mitigating the risk of AMR. In this direction, antivirulence strategies achieving targeted inhibition of bacterial virulence pathways/factors, including quorum sensing, efflux pumps, lectins, and iron chelators, have been widely explored against CF isolates of P. aeruginosa. Simultaneously, there have been discussions about the sufficiency of in vitro findings and their successful translation in pulmonary infection models (in vivo) for the clinical implementation of antivirulence therapies hence, this review article presents a bird’s eye view on the pulmonary infections involving P. aeruginosa in CF patients by laying emphasis on factors contributing to bacterial colonization, persistence, and disease progression along with the current line of therapeutics against P. aeruginosa in CF while underscoring the limitation of antimicrobial approaches. We further collate scientific literature and comprehensively discuss the various antivirulence strategies that have been successfully tested against P. aeruginosa isolates from CF patients. This could pave the way towards a paradigm shift towards clinical therapy of pseudomonal infections in CF and can potentially override conventional antimicrobial treatments.

The infections caused by various bacterial pathogens both in clinical and community settings represent a significant threat to public healthcare worldwide. The growing resistance to antimicrobial drugs acquired by bacterial species causing healthcare-associated infections has already become a life-threatening danger noticed by the World Health Organization. Several groups or lineages of bacterial isolates usually called ‘the clones of high risk’ often drive the spread of resistance within particular species. Thus, it is vitally important to reveal and track the spread of such clones and the mechanisms by which they acquire antibiotic resistance and enhance their survival skills. Currently, the analysis of whole genome sequences for bacterial isolates of interest is increasingly used for these purposes, including epidemiological surveillance and developing of spread prevention measures. However, the availability and uniformity of the data derived from the genomic sequences often represents a bottleneck for such investigations. In this dataset, we present the results of a comprehensive genomic epidemiology analysis of 17,546 genomes of a dangerous bacterial pathogen Acinetobacter baumannii. Important typing information including multilocus sequence typing (MLST)-based sequence types (STs), intrinsic blaOXA-51-like gene variants, capsular (KL) and oligosaccharide (OCL) types, CRISPR-Cas systems, and cgMLST profiles are presented, as well as the assignment of particular isolates to nine known international clones of high risk. The presence of antimicrobial resistance genes within the genomes is also reported. These data will be useful for researchers in the field of A. baumannii genomic epidemiology, resistance analysis and prevention measure development.

Emission, propagation, and reflection of light as mechanical phenomena in inertial frames are based on the behavior of balls at the limit when their mass is zero. The kinematics of massless balls is like that of balls with mass. Light as a wave or particle is a massless entity. Therefore, it is natural to apply the kinematics of the massless balls to light. Consequently, the kinematics of light depends on its kinetics of electromagnetic nature and its kinematics of mechanical nature in its interactions of emission and reflection with the matter. The study of the physics phenomena in the frame at absolute rest includes those in the inertial frames. Considering this and applying the emission, propagation, and reflection of light as mechanical phenomena in the vacuum of the frame at absolute rest, this study derives formulas for the speed of the wavefront of a ray of light reflected by a fixed and moving mirror when the light comes from a fixed and moving source. The derived formulas apply to the modified Michelson interferometer, employed independently by R. Tomaschek and D. C. Miller in their experiments.

Keywords: Wall-like RC columns; Strengthening; FRP; NSM rebars; Steel plates; Testing; FE modeling; Preloading.

We have developed a family of N-alkyl-nitrobenzamides that exhibit promising antitubercular ac-tivities. These compounds are a simplification of the structure of known inhibitors of DprE1, an essential Mtb enzyme and an emergent anti-TB target. The compounds were obtained by a simple synthetic methodology and their antitubercular, cyto-toxicity and stability were studied. The most active compounds were the 3,5-dinitro and the 3-nitro-5-trifluoromethyl derivatives. Lipophilicity was shown to be a main parameter modulating activity within each family. The most active compound presented MIC of 16 ng/mL and had in-termediate lipophilicities. The activity was also studied in a macrophage model of infection. In this model the compounds with chain lengths of 6 and 12 carbon atoms presented the best results, ex-hibiting activity profiles comparable to isoniazid. Docking studies performed suggested that the fit of our highly active compounds to the DprE1 binding pocket was very similar to the literature compounds. Furthermore, the metrics used in the analysis were able to distinguish between the families of the highly and least active compounds. Assessment of susceptibility over multiple species and computational together with the structure of the compounds are complementary information that supports DprE1 as a likely target of action for this type of compounds.

Utilizing bioinformatics tools, this study expands our understanding of secondary metabolism in Botrytis cinerea, identifying novel genes within polyketide synthase (PKS), non-ribosomal peptide synthetase (NRPS), sesquiterpene cyclase (STC), diterpene cyclase (DTC), and dimethylal-lyltryptophan synthase (DMATS) families. These findings enrich the genetic framework associ-ated with B. cinerea's pathogenicity and ecological adaptation, offering insights into uncharted metabolic pathways. Significantly, the discovery of previously unannotated genes provides new molecular targets for developing targeted antifungal strategies, promising to enhance crop pro-tection and advance our understanding of fungal biochemistry. This research not only broadens the scope of known secondary metabolites but also opens avenues for future exploration into B. cinerea's biosynthetic capabilities, potentially leading to novel antifungal compounds. Our work underscores the importance of integrating bioinformatics and genomics for fungal research, paving the way for sustainable agricultural practices by pinpointing precise molecular interven-tions against B. cinerea. This study sets a foundation for further investigations into the fungus's secondary metabolism, with implications for biotechnology and crop disease management.