The shear failure of surface methane capture borehole (SMCB) is the main cause of shortening life cycle of SMCB but lack of lithological analysis. In order to improve the stability of SMCB and improve efficient drainage period, it is of great significance to investigate the lithology performances for shear failure of SMCB. Based on the direct shear tests and geological method, the results shows that the shear displacement increases as the grain size decreases. Mechanical jump occurs at the lithological boundaries, which is mainly determined by the composition of rock specimens. The cohesion is the mainly possible reason for the step change of shear strength. Lithology with high quartz and low clay may effectively improve shear strength and failure resistance. Boreholes drilled into the weaker siltstone and mudstone sections may potentially experience preferential damage due to the larger shear displacement and shear strength. Protective measures at these sections may improve the stability of the borehole casing. The probing data where it was found that boreholes closure validated the prediction.

The development of a stationary phase material for high performance liquid chromatography based on a surface of silica hydride as opposed to silanols on ordinary silica is discussed including synthetic approaches, characterization and applications. There are several synthetic approaches available to create a silica hydride surface. Modification of the Si-H moiety on the silica surface can be accomplished through use of a hydrosilation reaction. Both the intermediate silica hydride and the material modified with an organic moiety can be characterized by a number of spectroscopic as well as a variety of other methods. Further insights into the retention mechanism are provide through chromatographic measurements. The ultimate utility of any chromatographic stationary phase material is determined by its success for solving challenging analytical problems. A broad range of applications are reviewed to illustrate the versatility and usefulness of silica hydride-based stationary phases.

In this paper, sea surface wind speed (SSWS) retrieval from Gaofen-3 (GF-3) quad-polarization stripmap (QPS) data in vertical-vertical (VV), horizontal-horizontal (HH) and vertical-horizontal (VH) polarizations is investigated in detail based on 3,170 scenes acquired from October 2016 to May 2018. The radiometric calibration factor of the VV polarization data is examined first. This calibration factor generally meets the requirement of SSWS retrieval accuracy with an absolute bias of less than 0.5 m/s but shows highly dispersed characteristics. These results lead to SSWS retrievals with a small bias of 0.18 m/s but a rather high root mean square error (RMSE) of 2.36 m/s compared with the ERA-Interim reanalysis model data. Two refitted polarization ratio (PR) models for the QPS HH polarization data are presented. Based on a combination of the incidence angle- and azimuth angle-dependent PR model and CMOD5.N, the SSWS derived from the QPS HH data shows a bias of 0.07 m/s and an RMSE of 2.26 m/s relative to the ERA-Interim reanalysis model wind speed. A linear function relating SSWS and the normalized radar cross section (NRCS) of QPS VH data is derived. The SSWS data retrieved from the QPS VH data show good agreement with the WindSat SSWS data, with a bias of 0.1 m/s and an RMSE of 2.02 m/s. We also apply the linear function to the GF-3 Wide ScanSAR data acquired for the typhoon SOULIK, which surprisingly yields a very good agreement with the model results. A comparison of SSWS retrievals among three different polarization datasets is also presented. The current study and our previous work demonstrate that the general accuracy of the SSWS retrieval based on GF-3 QPS data has an absolute bias of less than 0.3 m/s and an RMSE of 2.0 ±0.2 m/s relative to various datasets. Further improvement will depend on dedicated radiometric calibration efforts.

Face milling is a well known commercial process highly used in heavy industries that consumes high amount of power. Besides power issue, modern manufacturing industries are aiming for per part cost reduction keeping the product quality unimpaired. Unexpectedly if the part is rejected in any stage of manufacturing, the cost of manufacturing dramatically increases. Major cause of part rejection is excessive tool wear that imparts poor surface profile or catastrophic tool failure that causes adherence of broken tool debris onto machined surface. Furthermore, the tool wear is associated with sliding distance (frictional distance) and the tool life quantifies the cost of tools. As such, from the perspective of manufacturing industries it is imperative to optimize the surface quality parameter, cost of part, power consumption, and material removal – this is exactly what is accomplished here. By this work, it is possible to conserve power consumption, produce parts with lower cost, manufacture with uncompromising surface quality and enhanced material removal rate. Moreover, as intermediate factors of interest, the influences of sliding distance, tool life and tool flank wear on the overall machining performance are evaluated. The multi-objective optimization by Grey Relational Analysis (GRA) revealed that for improved product performance and fast manufacturing (case 1) optimum results are: feed per tooth fz = 0.25 mm/tooth, cutting speed vc = 392.6 m/min and cutting length l = 0.5 mm; for resource conservation (case 2) the optimum results are: feed per tooth fz = 0.125 mm/tooth, cutting speed vc = 392.6 m/min, cutting length l = 0.5 mm.

As an essential synthetic material used in continuous casting of steels, mold fluxes improve the surface quality of steel slabs. In this study, a CaO-SiO₂-Na₂O based low-fluorine mold flux was solidified by an improved water-cooled copper probe with different temperatures of molten flux and different probe immersion times. The heat flux through solid films and the film structures were calculated and inspected, respectively. The results indicate: large internal cracks (formed in the glassy layer of films during solidification) were observed, the formation and evolution of those cracks contributed to the the unstable heat flux density. The roughness of the surface in contacted with the water-cooled copper probe formed as films were still glassy and the roughness have no causal relationship with crystallization or devitrification. Combeite with columnar and faceted dendritic shapes is the main crystal in the film.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

We report the effects of surface passivation by depositing a hydrogenated amorphous silicon (a-Si:H) layer on the electrical characteristics of low temperature polycrystalline silicon thin film transistors (LTPS TFTs). The a-Si:H layer was optimized by hydrogen dilution and its structural and electrical characteristics were investigated. The a-Si:H layer in the transition region between a-Si:H and µc-Si:H resulted in superior device characteristics. Using an a-Si:H passivation layer, the field-effect mobility of the LTPS TFT was increased by 78.4% compared with a conventional LTPS TFT. Moreover, the leakage current measured at a V_GS of 5 V was suppressed because the defect sites at the poly-Si grain boundaries were well passivated. Our passivation layer, which allows thorough control of the crystallinity and passivation-quality, should be considered a candidate for high performance LTPS TFTs.

Water splitting plays an important role in electrochemical and photoelectrochemical conversion of energy devices. Electrochemical water splitting by the hydrogen evolution reaction (HER) is a straightforward route to produce hydrogen (H2), which requires an efficient electrocatalysts to minimize energy consumption. Recent advances have created a rapid rise in new electrocatalysts, particularly those based on non-precious metals. In this review, we present a comprehensive overview of the recent developments of ternary and quaternary 6d-group transition metal chalcogenides (TMCs) based electrocatalysts for water splitting, especially for HER. Detailed discussion is organized from binary to quaternary TMCs including, surface engineering, heterostructures, chalcogen substitutions, and hierarchically structural design in TMCs. Moreover, emphasis is placed on future research scope and important challenges facing these electrocatalysts for further development in their performance towards water splitting.

Almost 50 papers on surface plasmon resonance biosensors, published between 2016 and mid-2018, are reviewed. Papers concerning the determination of large particles such as vesicles, exosomes, cancer cells, living cells, stem cells and microRNA are excluded, as these are covered by a very recent review. The reviewed papers are categorized into five groups, depending on the degree of maturity of the reported solution: ranging from simple marker detection to clinical application of a previously developed biosensor. Instrumental solutions and details of biosensor construction are analyzed, including the chips, receptors and linkers used, as well as calibration strategies. Biosensors with a sandwich structure containing different nanoparticles are considered separately, as are SPR applications for investigating the interactions of biomolecules. An analysis is also made of the markers determined using the biosensors. Concluding, there is shown to be a growing number of SPR applications in the solution of real clinical problems.

Regarding number of vehicles, forest roads are characterized by low traffic intensity, but on the other hand great values of ground pressure between wheels of timber truck units and forest road surface occur, often with pressures values above 80 kN which additionally causes damage of the upper and lower forest road layer. There are currently several methods for assessing condition of a forest road surface which are mainly used for assessing state of public roads, but can be used in forestry as well. Assessing condition of forest road surface was done by measuring vibrations with a specially developed software for Android OS installed on a Huawei MediaPad 7 Lite. Software measured vibrations in all three axes, coordinates of device, speed of the vehicle and time. Aim of this research was to determine accuracy of collected data so that this method can be used for scientific and practical purposes. Research was carried out on the segment of a forest road during driving a vehicle equipped with a measuring device. Tests were performed in both driving direction of the forest road segment with different measuring frequencies, tyre inflation pressures and driving speeds. Values of vibrations were classified and translated on a map of forest road together with devices’ measured coordinates. Vibration values were compared with places of recorded forest road surface damages. Research results show no significant difference in vibration values between 1 Hz and 10 Hz of measurement frequencies. Based on the analysis of collected data and obtained results, it is clear that it is possible to assess the condition of a forest road surface by measuring vibrations. The greatest values of vibrations were recorded on the most damaged parts of the forest road. Vibrations do not depend on tyre inflation pressure, but ranges of vibrations are decreasing with decreasing driving speed. Accuracy of collected data depends on GPS signal quality, so it is recommended that each segment of forest road is recorded twice so that location of damages on forest road can be confirmed with certainty.

Optofluidics, a research discipline combining optics with microfluidics, currently aspires to revolutionize the analysis of biological and chemical samples e.g. for medicine, pharmacology, or molecular biology. In order to detect low concentrations of analytes in water, we developed an optofluidic device containing a nanostructured substrate for surface enhanced Raman spectroscopy (SERS). The geometry of the gold surface allows localized plasmon oscillations to give rise to the SERS effect, in which the Raman spectral lines are intensified by the interaction of the plasmonic field with the electrons in the molecular bonds. The SERS substrate was enclosed in a microfluidic system, which allowed transport and precise mixing of the analyzed fluids, while preventing contamination or abrasion of the highly sensitive substrate. To illustrate its practical use, we employed the device for quantitative detection of persistent environmental pollutant 1,2,3-trichloropropane in water in submillimolar concentrations. The developed sensor allows fast and simple quantification of halogenated compounds and it will contribute towards the environmental monitoring and enzymology experiments with engineered haloalkane dehalogenase enzymes.

It is well-known that surface plasmon wave propagates along a straight line, but this common sense was broken by the artificial curved light – plasmon Airy beam. In this paper, we introduce a new class of curved surface plasmon wave - the photonic hook plasmon. It propagates along wavelength scaled curved trajectory with radius less than surface plasmon polariton wavelength, and can exist despite the strong energy dissipation at the metal surface.

True contact between solids with randomly rough surfaces tends to occur at a large number of microscopic contact patches. So far, two scaling regimes have been identified for the number density n(A) of contact-patch sizes A in elastic, non-adhesive, self-affine contacts. At small A, n(A) is approximately constant, while n(A) decreases as a power law at large A. Using Green’s function molecular dynamics, we identify a characteristic (maximum) contact area Ac above which a superexponential decay of n(A) becomes apparent if the contact pressure is below the pressure p_cp at which contact percolates. We also find that A_c increases with load relatively slowly far away from contact percolation. Results for A_c can be estimated from the stress autocorrelation function G_σσ (r) with the following argument: the radius of characteristic contact patches, r_c, cannot be so large that G_σσ (r_c) is much less than p_c². Our findings provide a possible mechanism for the breakdown of the proportionality between friction and wear with load at large contact pressures and/or for surfaces with a large roll-off wavelength.

The aim of this study is to investigate, by means of experimental measurements and full-wave simulations, the dominant factors for the very high-resolution (VHR) radar image speckles from exponential correlated rough surfaces. A Ka-band radar system was used to collect the return signal from such a surface sample fabricated by 3D printing, and that signal was further processed into images at different resolution scales, where the image samples were obtained by horizontally turning around the surface sample. To cross-validate the results and to further discuss the VHR speckle properties, full wave simulations by full 3D Finite Difference Time Domain (FDTD) method were conducted with 1600 realizations for the speckle analysis. At the considered very high resolution, speckle statistics show divergence from the fully developed Rayleigh distribution. The factors that impact on the high-resolution speckle properties from exponential correlated rough surface, are analyzed in views of the equivalent number of scatterers theory and scattering scales, respectively. From the data results and extended discussions, it is evident that both of the above factors matter for VHR speckle of backscattering, from the exponential correlated rough surface as a good representative for the ground surface.

The surface planarity and asperity removal behaviors of atomic scale under the ultrathin water environment was studied for the nanoscale process by molecular dynamics simulation. The monolayer atomic removal was achieved under the noncontact and monoatomic layer contact conditions with different water film thickness, and the newly formed surface is relatively smooth and no deformed layer and plastic defects exist. The nanoscale processing is governed by the interatomic adhering action during which the water film transmits the loading forces to Cu surface and thereby result in the migration and removal of surface atoms. With scratching depth ≥ 0.5 nm, the abrasive particle squeezed out the water film from scratching region and scratched Cu surface directly, leading to the surface quality deterioration mainly governed by the plowing action. This study brings the goals of “0 nm planarity, 0 residual defects and 0 polishing pressure” closer to us in the nanoscale process for the development of ultra-precision manufacture technology.

Surface Plasmon Resonance (SPR) based sensors have the advantage of being label-free, enzyme-free and real-time. However, their spreading in multidisciplinary research is still limited and almost confined to prism-coupled devices. Plasmonic gratings, combined with a simple and cost-effective instrumentation, have been poorly developed compared to prism-coupled system mainly due to their lower sensitivity. Here we describe the optimization and signal enhancement of a sensing platform based on phase-interrogation method, which entails the exploitation of a nanostructured sensor. This technique is particularly suitable for integration of the plasmonic sensor in a lab-on-a-chip platform and can be used in a microfluidic circuit to ease the sensing procedures and limit the injected volume. The careful optimization of most suitable experimental parameters by numerical simulations leads to a 30 to 50% enhancement of SPR response, opening new possibilities for applications in the biomedical research field while maintaining the ease and versatility of the configuration.

An automated discharge imaging system (ADIS), a non-intrusive and safe approach, was developed for measuring river flows during flash flood events. ADIS consists of dual cameras to capture complete surface images in the near and far fields. Surface velocities are accurately measured using the Large Scale Particle Image Velocimetry (LSPIV) technique. The stream discharges are then obtained from the depth-averaged velocity (based upon an empirical velocity-index relationship) and cross-section area. The ADIS was deployed at the Yu-Feng gauging station in Shimen Reservoir upper catchment, northern Taiwan. For a rigorous validation, surface velocity measurements were conducted using ADIS/LSPIV and other instruments. In terms of the averaged surface velocity, all measured results were in good agreement with small differences, i.e., 0.004 to 0.39 m/s and 0.023 to 0.345 m/s when compared to those from acoustic Doppler current profiler (ADCP) and surface velocity radar (SVR), respectively. The ADIS/LSPIV was further applied to measure surface velocities and discharges during typhoon events (i.e., Chan-Hom, Soudelor, Goni, and Dujuan) in 2015. The measured water level and surface velocity both showed rapid increases due to flash floods. The estimated discharges from ADIS/LSPIV and ADCP were compared, presenting good consistency with correlation coefficient R = 0.996 and normalized root mean square error NRMSE = 7.96%. The results of sensitivity analysis indicate that components till (τ) and roll (θ) of the camera are most sensitive parameter to affect the surface velocity using ADIS/LSPIV. Overall, the ADIS based upon LSPIV technique effectively measures surface velocities for reliable estimations of river discharges during typhoon events.

Unmanned Aerial Vehicles (UAVs) are now filling in the gaps between spaceborne and ground-based observations and enhancing the spatial resolution and temporal coverage of data acquisition. In the realm of hydrological observations, UAVs have a key role to quantitatively characterize the surface flow allowing for remotely accessing the water body of interest. In this paper we propose a technology which uses a sensing platform encompassing a drone and a camera to determine the water level. The images acquired my means of the sensing platform are then analyzed using the Canny method to detect the edges of water level and of Ground Control Points (GCPs) used as reference points. The water level is then retrieved from images and compared to a benchmark value obtained by a traditional device. The method is tested at four locations in an artificial lake in central Italy. Results are encouraging as the overall mean error between estimated and true water level values is around 0.02 m. This technology is well suited to improve hydraulic modeling and thus provide a reliable support to flood mitigation strategies also in uneasy-to-access environments.

Solar energy is derived from photons of light coming from the sun in a form called radiation. Solar energy finds extensive application in air and water heating, solar cooking, as well as electrical power generation, depending on the way of capturing, converting and distribution. To enable such application, it is necessary to analyze the horizontal tilt angle of horizontal surfaces – in order that when the solar energy reaches the earth surface to be completely absorbed. This paper tends to describe the availability of solar radiation for south-facing flat surfaces. The optimal monthly, seasonal, and annual tilt angles have been estimated for Pristina. The solar radiation received by the incident plane is estimated based on isotropic sky analysis models, namely Liu and Jordan model. The annual optimum tilt angle for Pristina was found to be 34.7°. The determination of annual solar energy gains is done by applying the optimal monthly, seasonal and annual tilt angles for an inclined surface compared to a horizontal surface. Monthly, seasonal and annual percentages of solar energy gains have been estimated to be 21.35%, 19.98%, and 14.43%. Losses of solar energy were estimated by 1.13 % when a surface was fixed at a seasonal optimum tilt angle, and when it was fixed at an annual optimum tilt angle, those losses were 5.7%.

Due to the fact that abrasive media can deform flexibly in abrasive flow machining (AFM) making this method easily to polish the complex holes and the curved surface of the hard machining shapes. Although abrasive media dominate the polishing behavior in AFM process, the mechanism of the abrasive media are not easy to understand because of the high viscous gels, therefore, many finishing works need lots of time to design AFM process. Power laws of the abrasive gels is studied here to evaluate the non-Newtonian flow of abrasive gels in complex holes polishing firstly, at the mean time different abrasive gels are utilized to finish the complex holes to follow the results by non-Newtonian flow calculation. Moreover, traditional AFM has difficulty to achieve a uniform roughness of radial distribution in the complex holes polishing because of the non-uniform abrasive forces. So a helical passageway is proposed to create a multiple motion of abrasive medium and to obtain the even surface of the complex holes in AFM process.

Here, we consider a closed composite system consisting of a primary system where the chemical reaction occurs and is located in a p, T reservoir. In the ideal isentropic case (thermodynamic process), the change in the internal energy of the composite system (due to a chemical reaction) is wholly converted into useful work - maximum useful work. Irreversibility - a measure for the degradation of useful work - in a closed system generates entropy, i.e., the thermodynamic process is no longer isentropic. Applying the principle of maximum entropy and minimum internal energy to a part of the system's total volume and applying the elements of the system's volume for which the law of local equilibrium applies useful work and irreversibility can be defined. Suppose the primary system is viewed as a set of black box volume elements in which a chemical reaction occurs. In that case, the criterion of an isentropic process or a process with entropy generation becomes the Gibbs-Duham equation. It has been proven that De Donder's equation of entropy production of a chemical reaction is a particular form of Calen's equation –TdST = dUT where dST is the differential change of total entropy and dUT is the differential change of total internal energy of the composite system.

Background/Objectives: Head and neck free flap reconstructions are often required to treat tumors or extensive post-traumatic jaw defects. The facial artery is the standard receiving vessel for intraoral microvascular anastomoses. However, its use is associated with several disadvantages, such as lesions of buccal nerve branches or the parotid duct and variability in course and diameter. This study aims to investigate whether sublingual artery branches can be considered an alternative intraoral supply vessel to the facial artery to avoid these drawbacks. Methods: 12 formalin-fixed cadaveric heads with 24 sides were dissected. The sublingual artery's origin, course, branching pattern, and distribution were examined. In addition, the diameters of the branches of the sublingual artery were assessed to identify potential supply vessels for anastomoses. Results: In ten of the 24 cases (41.7 %), the sublingual artery originated from the lingual artery and nine cases (37.5 %) from the facial artery. The main trunk of the sublingual artery was present in the floor of the mouth in all cases (100 %) with a diameter of ≥ 0.9 mm in vitro (1 mm in vivo). In 15 of the 24 half heads (62.5 %), branches of the sublingual artery with ≥ 0.9 mm were identified in this space. Conclusions: The large diameter of the sublingual artery on the floor of the mandible suggests that this vessel or its branches could be considered alternative pedicles for intraoral anastomoses in mandibular microvascular free flap grafts.

Combined hepatocellular cholangiocarcinoma (cHCC-ICC) is a rare malignancy that involves a combination of features of hepatocellular carcinoma and intrahepatic cholangiocarcinoma (ICC). cHCC-ICC is generally considered to exhibit a more aggressive clinical course compared to ICC; however, its risk factors and outcomes remain largely undefined. A single-center retrospective study of 82 patients diagnosed with ICC or cHCC-ICC from June 2011 and January 2023, all of whom underwent surgical resection. Our analysis included 70 patients with resected ICC and 12 with resected cHCC-ICC. The overall survival (OS) for the entire cohort was 21.6 months, with a recurrence-free survival (RFS) of 11.8 months. The cHCC-ICC group had significantly higher levels of AST and ALT (AST median 206 vs. 46; ALT median 165.5 vs. 48; p=0.012 and p=0.013, respectively), whereas the ICC group had higher alkaline phosphatase (median 66 vs. 104; p=0.03). CA 19-9 values (p=0.02) were higher in the ICC group, while AFP values were higher in the cHCC-ICC group (p=0.0004). The cHCC-ICC group had a significantly higher rate of recurrence (83% vs. 47%, p=0.028) with a significantly decreased RFS (4.7 months vs. 12.4 months; log-rank p=0.007). cHCC-ICC is a rare entity that needs to be further studied to improve patient outcomes. Our study showed that RFS is lower in the cHCC-ICC group as compared to ICC patients alone. Further studies are warranted and possibly suggest the need for more aggressive initial treatment strategies in patients diagnosed with cHCC-ICC.

Abstract Precision medicine is essentially based on reliable and non-invasive biomarkers. Aim of this review has been to describe the newest biomarkers in the field of kidney transplantation and the kidney rejection, one of the commonest and severe complications. Standard of care tools to identify acute rejection are largely full of errors and of drawbacks. In recent years new and reliable biomarkers have been found. They are avoid of risks, non-invasive and able to detect rejection even in those frequent cases in which acute rejection are clinically asymptomatic and not otherwise identifiable. In recent years several biomarkers have been identified. Very recently have been found new relevant biomarkers able to diagnose rejection with high positive predictive value and low negative predictive value. These are the donor derived cell free DNA found in the recipient, the gene expression profile of the donor found in the recipient and the urinary cytokines that express modification in the graft tissue. The aim of this study has been to find the most recent findings in the literature on this topic and to describe the utility and possible limitation of such new biomarkers on kidney rejection.

The purpose of this study is to show an automated laser vision correction (LVC) with the transep-ithelial refractive keratectomy (TransPRK) surgery technique. Since more surgical steps have been automated over the years, we have standardized the TransPRK technique. We have been using it since 2010. This paper aims to illustrate the processes that are readily applicable to automation. To meet the patient's expectations and ensure that the patient has uncorrected visual acuity at least equal to the preoperative corrected vision with glasses, patient selection is crucial in refractive surgical procedures. One major benefit of automating the surgery is that it can be performed in a similar way by each surgeon or laser correction centre, so once the standard and results are good, these can be per-formed by different surgeons.

Study design: Technical note. Objectives: To present a new technique of treatment for a patient with thoracolumbar focal kyphosis due to osteoporotic verte-bral fracture (OVFs). Background : OVFs are common among the elderly population. Following a severe wedged fracture, patients often experience low back pain and disruptions in activities of daily living. Reconstruction surgeries, such as corpectomy, are among the treatment options for this condition. However, corpectomy requires longer surgical times and involves a significant amount of blood loss. Materials and Methods : An 80-year-old woman presented to our hospital with severe low back pain and gait disturbance. She had experienced an L2 OVF six years prior. Although she had no neurological deficit, she could not walk more than 200m due to pain. Preoperative spinal radiographs revealed severe sagittal malalignment, with the L2 vertebra collapsed and focal kyphosis of L1-3 measuring 34 degrees. Results: The patient underwent anterior and posterior surgery in the right decubitus position using a C-arm free technique. The surgical time was 133 minutes with an estimated blood loss of 100 ml. Hyperlordotic cages were inserted in the upper and lower disc space via a lateral approach, while percutaneous pedicle screws (PPS) were inserted from a posterior approach. These procedures were performed simultaneously under navigation guidance only. Post-operative images showed excellent spinal alignment, with local kyphosis reduced from 34 to 14 degrees, and no major or severe complications occurred. At one-year follow-up, the patient was able to walk smoothly, with her visual analogue scale for low back pain improving from 73mm to 13mm, and her Oswestry Disability Index improving from 53.3% to 13.3%. Conclusions/Level of Evidence : The simultaneous use of hyperlordotic cages and PPS is an effective and innovative navigation technique that yields promising outcomes for thoracolumbar focal kyphosis resulting from OVFs. This approach not only reduces surgical time but also minimizes intraoperative blood loss. Level V.

The detection and analysis of small molecules, typically defined as molecules under 1000 Da, is of growing interest ranging from the development of small molecule drugs and inhibitors to the sensing of toxins and biomarkers. However, due to challenges such as their small size and low mass, many biosensing technologies struggle to have the sensitivity and selectivity for the detection of small molecules. Notably, their small size limits the usage of labeled techniques that can change the properties of small molecule analytes. Furthermore, the capability of real-time detection is highly desired for small molecule biosensors’ application in diagnostics or screening. This review highlights recent advances in label-free real-time biosensing technologies utilizing different types of transducers to meet the growing demand for small molecule detection.

Modification the biodegradable matrix was carried by graft-copolymerization polylactide with methacrylic acid of various concentrations. Ultraviolet irradiation with different exposure times to the samples was chosen as the initiator of copolymerization. In the experiment the effect of ultraviolet light on polylactide and graft copolymerization was investigated: the resulting samples were studied by viscosimetry, gravimetry, FTIR, static cation- exchange capacity analysis . The conditions for obtaining grafted copolymers and the dependence of the characteristics on the reaction conditions are established.

Background: Malnutrition was associated with worse survival outcomes, impaired quality of life, and deteriorated performance status across various cancer types. We aimed to identify risk factors for malnutrition in patients with epithelial ovarian(EOC) and impact on survival. Methods: In our prospective study, we included the patients with primary and recurrent EOC, tubal or peritoneal cancer conducted. We assessed serum laboratory parameters, body mass index, nutritional risk index, nutritional risk screening score(NRS-2002), and bio-electrical impedance analysis. Results: We recruited a total of 152. Patients >65 years-old, with ascites of >500 ml, or with platinum-resistant EOC showed statistically significant increased risk of malnutrition when evaluated by NRS-2002(p-values = 0.014, 0.001, and 0.007, respectively). An NRS-2002<3 was an independent predictive factor for complete tumor resectability (p=0.009). The patients with NRS-2002≥3 had a median overall survival(OS) of seven months (95% CI=0-24 months), as compared to the patients with NRS-2002<3 where median OS was 46 months(p=0,001). Phase angle(PhAα)≤ 4.5 was the strongest predictor of OS. Conclusion: Malnutrition is an independent predictor of incomplete cytoreduction in study population. It is an independent prognostic factor for poor OS. Preoperative nutritional assessment is an effective tool in identification of high-risk groups within EOC characterized by poor clinical outcome.

Considering the aging society and budget constraints, a strategy for reforming public transportation welfare policies is essential for sustainability. Among the various transportation welfare policies, fare discount policies are provided to specific age groups, and most countries offer benefits to several public transportation. South Korea provides a fare-free policy limited to subways, and the need for policy modification is emerging due to sustainability problems caused by an aging society. Hence, the scope of the policy should be expanded to all travel modes, but the discount rate should be reduced, or the target group should be reduced in consideration of the budget. This study proposes a travel mode to focus on by city through the preference of the elderly. The latent class model is employed to classfy stated preference data collected from the survey. The estimation results show a significant preference heterogeneity depending on the level of subway supply by region, and a policy focused on subways would be more reasonable in cities with sufficient subway infrastructure. Hence, regarding sustainability, it may be more appropriate to focus on specific means than to provide the same discount policy for all public transport.

Proteins in biological systems function at the interface of single molecule and bulk chemistry and thus provide novel insights into the basic physical chemistry of scaling and emergent phenomena. For example, a binary mechanical model based on the chemistry of muscle contraction unifies molecular mechanics and thermodynamics and provides an explicit solution to the Gibbs paradox. Using the same model system, here I show that chemical activities of molecular states have no effect on chemical kinetics or energetics. Specifically, while the concentration or number of molecules in a molecular state is widely thought to contribute to reaction free energies, here I show that it is not the physical presence of molecules that pushes a reaction forward but the number of microstates, , accessible in a chemical state that pulls a reaction toward equilibrium with an entropic force down an entropic funnel. With the derivation of an entropic contribution to chemical kinetics, I develop a novel chemical kinetic formulation that fully describes the chemical thermodynamics of both equilibrium and non-equilibrium reactions in terms of an a priori system reaction energy landscape.

Iron oxide nanozymes are a form of nanomaterial with both superparamagnetic and enzyme-mimicking properties. Given the multifunctional nature of iron oxide nanozymes, it is attractive for creating iron oxide hybrid nanozymes through biomolecular modifications to imbue with auxillary properties. Such iron oxide hybrid nanozymes can be useful for rapid and cost-effective analysis of circulating tumor nucleic acids (ctNAs) in patient liquid biopsies during minimal residual disease (MRD) monitoring of cancer recurrence. Herein, the use of streptavidin-modified iron oxide hybrid nanozymes is reported for magnetic enrichment and bioelectrocatalytic sensing of three prostate cancer (PCa) ctRNA biomarkers with high detection specificity and sensitivity (10 copies) over an ultrabroad dynamic range (five orders of magnitude). Furthermore, the feasibility of ctRNA analysis for pre- and post-cancer treatment MRD monitoring is demonstrated using PCa urinary liquid biopsy samples.

Biosensors have shown great potential in realizing rapid, low cost and portable on-site detection for diseases. This work reports the development of a new bioelectronic sensor called AC electrokinetics-based capacitive (ABC) biosensor, for the detection of genomic DNA (gDNA) of methicillin-resistant Staphylococcus aureus (MRSA). The ABC sensor is based on interdigitated microelectrodes biofunctionalized with oligonucleotide probes. It uses a special AC signal for direct capacitive monitoring of topological change on nanostructured sensor surface, which simultaneously induce dieletrophoretic enrichment of target gDNAs. As a result, rapid and specific detection of gDNA/probe hybridization can be realized with high sensitivity. It requires no signal amplification such as labelling, hybridization chain reaction, or nucleic acid sequence-based amplification. This method involves only simple sample preparation. After optimization of nano-structured sensor surface and signal processing, the ABC sensor demonstrated fast turnaround of results (~10 s detection), excellent sensitivity (a detection limit of 4.7 DNA copies /µL MRSA gDNA) and high specificity, suitable for point of care diagnosis. As a bioelectronic sensor, the developed ABC sensors can be easily adapted for detection of other infectious agents.

The aim of this study was characterization of some dairy drinks based on Milk Serum regarding major whey proteins (WP) and free amino acids (FAAs) using reversed phase high performance liquid chromatographic (RP-HPLC) methods. The studied WP, -lactalbumin (-La), bovine serum albumin (BSA), -lactoglobulin A (-Lg A) and -lactoglobulin B (-Lg B) were separated on Aeris XB-C18 column at 214 nm detection. The RP-HPLC method was validated by selectivity, linearity (R2 ≥0.99), sensitivity (LOQ, 1.35–10.08 µg mL−1), accuracy (recovery 96.79-103.07%) and precision (% RSD ≤ 4.13%). The total studied WP in studied dairy drinks varied between 1.42 and 3.047 g·L-1. The chromatographic profile of FAAs (aspartic acid, glutamic acid, serine, histidine, arginine, glycine, threonine, alanine, tyrosine, cysteine, tryptophan, methionine, valine, phenylalanine, isoleucine, leucine and lysine) was determined in lyophilized concentrate of Milk Serum by RP-HPLC using pre-column derivatization reaction with orthophthalaldehyde (OPA). The total studied FAAs in studied samples varied between 1.103 and 1.119 mg·g-1. Moreover, the Milk Serum showed bacteriostatic activity against two bacterial strains Escherichia coli and Staphylococcus aureus. The obtained results confirm that dairy drinks based on the Milk Serum constitutes a valuable sources of bioactive components with benefits for human healthy nutrition.

Eddy current based approaches have been investigated for a wide range of inspection applications. Dodd-Deeds model and the truncated region eigenfunction expansion (TREE) method are widely applied in various occasions, mostly for the cases that the sample is relatively larger than the radius of the sensor coil. The TREE method converts the integral expressions to the summation of many terms in the truncated region. In a recent work, the impedance of the co-axial air-cored sensor due to a plate of finite radius was calculated by the modified Dodd-Deeds analytical approach proposed by authors. In this paper, combining the modified analytical solution and the TREE method, a new finite region eigenfunction expansion (FREE) method is proposed. This method involves modifying its initial summation point from the first zero of the Bessel function to a value related to the radius of the plate, therefore makes it suitable for plate with finite dimensions. Experiments and simulations have been carried out and compared for the verification of the proposed method. Further, the planar size measurements of the metallic circular plate can be achieved by utilising the measured peak frequency feature.

As there exist no repulsive forces in strong interaction, in a hypothetical approach, strong interaction can be assumed to be equivalent to a large gravitational coupling. Based on this concept, strong coupling constant can be defined as a ratio of the electromagnetic force and the gravitational force associated with proton, neutron, up quark and down quark. With respect to the product of strong coupling constant and fine structure ratio, we review our recently proposed two semi empirical relations and coefficients 0.00189 and 0.00642 connected with nuclear stability and binding energy. We wish to emphasize that- by classifying nucleons as ‘free nucleons’ and ‘active nucleons’, nuclear binding energy can be fitted with a new class of ‘three term’ formula having one unique energy coefficient. Based on the geometry and quantum nature, currently believed harmonic oscillator and spin orbit magic numbers can be considered as the lower and upper “mass limits” of quark clusters.

Data creation is often the only way for researchers to produce basic geospatial information for the pursuit of more complex tasks and procedures such as those that lead to the production of new data for studies concerning river basins, slope morphodynamics, applied geomorphology and geology, urban and territorial planning, detailed studies, for example, in architecture and civil engineering, among others. This exercise results from a reflection where specific data processing tasks executed in Google Sketchup (Pro version, 2018) can be used in a context of interoperability with Geographical Information Systems (GIS) software. The focus is based on the production of contour lines and Digital Elevation Models (DEM) using an innovative sequence of tasks and procedures in both environments (GS and GIS). It starts in Google Sketchup (GS) graphic interface, with the selection of a satellite image referring to the study area—which can be anywhere on Earth's surface; subsequent processing steps lead to the production of elevation data at the selected scale and equidistance. This new data must be exported to GIS software in vector formats such as Autodesk Design Web format—DWG or Autodesk Drawing Exchange format—DXF. In this essay the option for the use of GIS Open Source Software (gvSIG and QGIS) was made. Correcting the original SHP by removing “data noise” that resulted from DXF file conversion permits the author to create new clean vector data in SHP format and, at a later stage, generate DEM data. This means that new elevation data becomes available, using simple but intuitive and interoperable procedures and techniques which confgures a costless work flow.

Among the most important variables in the design of falling film microreactors (FFMRs) is the liquid film thickness as well as the gas/liquid interfacial area, which dictate the mass and heat transfer rates. In a previous work conducted in our lab the characteristics of a free-falling Newtonian liquid film have been studied and appropriate correlations have been proposed. In this work the geometrical characteristics of a non-Newtonian shear thinning liquid, flowing in an inclined open microchannel, have been experimentally investigated and design correlations that can predict with reasonable accuracy the features of a FFMR have been proposed. The test section used was an open μ-channel with square cross section (Wo=1200 μm) made of brass which can be set to various inclination angles. The liquid film characteristics were measured by a non-intrusive technique that is based on the features of a μ-PIV system. Relevant CFD simulations revealed that the volume average dynamic viscosity over the flow domain is practically the same as the corresponding asymptotic viscosity value, which can thus be used in proposed the design equations. Finally, a generalized algorithm for the design of FFMRs, containing non-Newtonian shear thinning liquids, is suggested.

The article reviews the current status of label-free integrated optical sensors focusing on the evolution over the years of their analytical performance. At first a short introduction to the evanescent wave optics is provided followed by detailed description of the main categories of label-free optical sensors including sensors based on surface plasmon resonance (SPR), grating coupler, photonic crystals, ring resonators and interferometric transducers. After a short reference to SPR techniques, including localized SPR, integrated optical sensors i.e., grating-couplers, interferometers, photonic crystals, microring resonators are reviewed. For each type of sensor, the detection principle is first provided followed by description of the different transducer configurations so far developed and their performance as biosensors. Finally, a short discussion about the current limitations and future perspectives of integrated label-free biosensors optical sensors is provided

Viruses can infect a cell via one or both routes viz. cell-to-cell (c-c) or cell-free (c-f) . Pathogenesis studies of various viruses, including HIV, have shown that c-c transmission yields a significantly higher infection magnitude than the c-f route. Expectedly, potent antibodies inhibited c-f infection more efficiently than with c-cell transmission. To achieve a one-step, synchronous infection cycle that provides amplified infection, we have studied a consistent and efficient c-c HIV infection model since 1992. H9 cells persistently infected with HTLV-IIIB (H3B cells) and uninfected target CD4+ lymphocyte line (HuT78) were mixed in a ratio of 1:4 respectively. We have recently used this model to produce HIV designer antigens that have been shown to elicit monoclonal as well as polyclonal specific antibodies against novel epitopes that are formed post virus-cell engagement, but prior to fusion. The model can be extended for HIV neutralizing antibody assays or drug inhibitors against high multiplicity of infection.

In Europe we can see a change in the social structure in the last period. Average life expectancy has increased dramatically over the last 50 years. Because of the improved life situation and advanced level of health care, older people are slower. With advancing age, the likelihood of experiencing a variety of constraints such as visual impairment, reduced hearing or physical ability increases. In such a life stage tenants are often forced to leave their long-term living space because these homes can not serve "new" individual needs and the resulting personal protection goal. This transition from the privacy of their home to the new environment often appears to be a painful change. They will take their familiar and well-known surroundings, because their homes can not be adapted to serve new needs. It must be the policy’s role to create a new inclusive social space and the requirement for architects and designers to create new goals for the design of an adaptable environment. This is a comprehensive approach to the design of the outer and inner space that could serve people even if there is an unexpected situation and changes in movement and physiological limitations of older people. The contribution shows the results of the survey conducted in Germany and Slovakia. In the survey respondents expressed their opinion on what they considered important in creating an adaptive environment. Results are processed graphically with explanation. The results were mainly for designers and developers of the indoor environment. Based on the results of the questionnaire survey, studies of possible modifications in the interior of the flats were then prepared. The contribution yielded these results in three age groups of respondents; i. people aged 35, 50 and over 50.

Diamidophosphate has been identified as a possible prebiotic compound used in the precursor membranes of the first ‘life’. Compounds such as these will be helpful in developing novel biomimetic approaches in synthetic chemistry. Thermochemical data for this type of compounds are not available. Hess’ law and estimates from calorimetric measurements used by Wakefield in the 1970s for other amido phosphates have been used to estimate the thermochemical values for the diamido and monoamido-phosphoric acid. Enthalpy of formation at 298.15 ^oC is calculated as – 821.9 kJ/mol and the free energy of formation calculated as -813.5 kJ/mol for the diamidophosphoric acid. The calculated enthalpy of formation of monoamidic phosphoric acid is -1117.1 kJ/mol and its free energy of formation is - -1105 kJ/mol.

The relationship of the animal with its environment has been of longstanding interest in philosophy and science. Here I provide a brief introduction to concepts that place an emphasis on mutualism as the basis of organism - environment interaction, in contrast to the long standing view that the environment exerts an instrumental role in shaping the organism. Two influential theories have been von Uexküll’s theory of umwelt and Gibson’s theory of affordances. The former envisioned the animal as immersed in its surroundings (umwelt) to form a functional unit. In a similar manner, the latter theory describes a unity between 1) environmental information that provides the animal with opportunities for action (affordances) and 2) the ability of the animal to perceive and engage with those affordances. These views have influenced more recent ecological models of the organism as the functional unit of biology and have also influenced models of immune function. In ecological models, agency is seen as the ability of the organism to predict and control its engagement with the environment in order to maintain its integrity. The predominant contemporary model of neural function in which perception and action are understood to operate through Bayes-like active inference complements the concept of agency as proposed by the mutualism models. However, it is suggested that rather than a constant mutualism, encounters between organism and environment range over a dynamic spectrum from dualism to mutualism. It is also suggested that along this spectrum, agency emerges when the balance of instrumentality shifts from the environment to the organism, and that the balance of this relationship can further progress towards a felicitous mutualism. Meaning emerges between environmental information and an agent as opportunity for action. Implications for opportunities to foster agency in animals within our care is noted.

This article investigates a proposed new mathematical model that considers the infected individuals using various rate coefficients such as transmission, progression, recovery and vaccination. The fact that the dynamic analysis is completely determined by the basic reproduction number is established. More specifically, local and global stabilities of the disease-free equilibrium and the endemic equilibrium are proved under certain parameter conditions when the basic reproduction number is below or above unity. A realistic computer simulation is performed for better understanding of the variations in trends of different compartments after the outbreak of the disease.

Background: Posterior malleolar fractures (PMFs) account for 7-44% of all ankle fractures, and are crucial for ankle stability, associated with poorer functional outcomes and higher rates of traumatic arthritis. Despite the exact mechanism and treatment strategy of this kind of fractures still remain controversial, most orthopaedic surgeons tend to treat PMFs with open reduction internal fixation method. To achieve rigid fixation for the fragment, screws should be inserted across the fracture plane perpendicularly. However, the study on the spatial geometry of the fracture surface of PMFs, especially the trend surface, has not been reported before.Objective: This study aimed to construct the trend surface of PMFs and establish an algorithm to better understand the spatial geometry of the fracture surface, which could guide treatment strategies.Methods: A retrospective analysis of CT images of PMFs from January 2021 to January 2024 was conducted. Cases were grouped according to the Bartoníček classification system. The skeletal ankle models were reconstructed, which were then transformed into CAD models. Fracture surfaces were segmented, and point clouds were output to record coordinate values. The K-Dimensional Tree data structure was built for the efficient indexcality of the Depth-First-Search algorithm to find the matched points in the clouds. The average point was computed for matched points, and subsequently, the fracture trend surface and heat map were generated.Results: Twenty-four cases were included. The posterior malleolar fracture trend surface was composed of two surfaces, each approximated as a plane and intersect an angle about 130.5°. The posterolateral surface extended slightly curvingly from the posterior two-fifths of the fibular notch to the posteromedial one-third of the distal tibia, formed an angle of 10.1° with the tibia axis and 10.1° with the coronal plan of the lower leg. The posteromedial surface extended from the posteromedial one-third of the distal tibia towards the intercollicular groove, formed an angle of 5.2° with the tibia axis and 39.4° with the coronal plan of the lower leg. The heat map revealed that the high-frequency fracture regions presented at 16.0mm away from the posterior malleolar distal edge and 11.2mm medial to the posterior margin of the fibular notch.Conclusion: The study provides a novel perspective on PMFs by describing the spatial geometric morphology of the fracture surface. This can be useful for the treatment strategies. 1. The fracture lines on the bone surface help us generate a stereoscopic model of the fracture surface in our brain, but this model may not be the same as the true fracture surface. 2. In A-P fluoroscopic view, 16.0mm away from the posterior malleolar distal edge and 11.2mm medial to the posterior margin of the fibular notch were the high frequency regions where the fracture surfaces passed through. 3. To firmly hold the posterolateral PMF, 3 key screws should be parallelly inserted into the distal tibia through the fragment, oriented medially 10.4°, cephalad 10°. The insertion points of the screws, in back view, are individually identified at 8.3mm, 16.9mm, 8.3mm superior to the inferior margin of the posterior malleolus, and 6.0mm,10.5mm, 15.1mm posterior to the posterior margin of the fibular notch. The depth of the screws should be no more than 40mm to avoid irritating the anterior tendons, vessels and nerves.

In this work, we investigate how to obtain the optimal active elements in Hybrid Relay-Reflecting Intelligent Surface (HR-RIS) systems while considering enhancing the sum rate of the communication system in the presence of malevolent eavesdropper. Therefore, when dealing with numerous elements in the HR-RIS, the complicated optimization task of activating and deactivating the active elements of RIS renders typical exhaustive search methods impracticable. Standard techniques, such as alternating optimization, often frequently converge and unfortunately become trapped in local optima, leading to less-than-ideal results. To address these issues, we suggest performing the Jaya algorithm, which modifies its search strategy in response to historical data to find a compromise between investigating novel avenues and taking advantage of well-established answers. Our simulation findings demonstrate that this strategy outperforms the most recent techniques, yielding higher sum rates with the best possible user location and robust security against eavesdropping. It’s interesting to observe that even at lower total power levels, the Jaya algorithm performs incredibly well and efficiently identifies the optimal amount of active elements. This demonstrates how it can decrease interference, increase signal quality, improve Signal-to-Interference-plus-Noise Ratio (SINR), and increase secrecy rates, opening the door for more efficient and secure wireless communication systems.

Most available studies on the mechanical properties of apples lack the comprehensive results needed for the construction and validation of FEM models. Researchers typically focus on either the flesh and epidermis or the whole fruit, often overlooking the maturity stage of the examined apples. They usually report only firmness or the starch index as indicators of maturity. Furthermore, many studies use store-bought apples, which is impractical for industrial applications since this fruit have already undergone various treatments before reaching the shelf. This article aims to determine the mechanical properties of apples necessary for constructing FEM models that are both adequate and useful for the industry. The new Polish apple variety, Chopin, was selected as the research material. The study was conducted for three stages of apple maturity: development, ripening, and senescence. Mechanical properties of the flesh and skin were determined as material data for FEM models. Force-displacement curves and pressure-force functions were examined for future model validation. Using micro-computed tomography, the bruise volumes of fruit subjected to 20%, 50%, and 80% of the destructive force were determined. Significant differences were found between apples in the senescence stage and those in the development and ripening stages. Results of Micro-Ct and the results of modified and real compression tests of whole fruit have allowed us to formulate the research hypothesis regarding the influence of flesh cracking (characterized by local drops of force), influencing the bruise visibility and detection.

Aiming at the problem of underactuated unmanned surface vehicles (USVs) performing fixed-point operations in the sea but without dynamic positioning control system. This paper introduces an original approach for positioning control, and the method is named as virtual anchor control method. This method is applicable in slow-varying current environments, and this approach does not need the prior knowledge of current information or vessel motion model parameters, thus offering convenient usability. This method is comprised by four steps. Firstly, a linear concise motion model with unknown disturbances is proposed. Then, the motion planning law is designed by imitating underlying principles of ship anchoring. Next, an adaptive disturbance observer is proposed for estimating uncertainties in the motion model. Last step, based on the observer, a sliding-mode method is used for heading control law designing, and thrust control law is also conducted by applying the Lyapunov method. Finally, numerical simulation experiments with significant disturbances and tidal current variations are conducted, which demonstrate that the proposed method has good control effect and robustness.

Titanium alloys, notably Ti6Al4V, are frequently employed in biomedical applications due to their high mechanical strength and biocompatibility. But improving their surface qualities like biocompatibility and resistance to corrosion remains a crucial topic of study. This study investigates the effects of rhenium-carbon coatings deposited on Ti6Al4V substrates using magnetron sputtering technique with a molybdenum anchoring layer. Despite successful formation of rhenium carbides, elemental rhenium, and rhenium oxides confirmed by EDS and XRD analysis, the coatings exhibited poor adhesion, resulting in significant delamination as observed in SEM images. Corrosion resistance tests revealed that the coatings adversely affected the Ti6Al4V substrate, as indicated by increased corrosion current densities and more negative corrosion potentials in potentiodynamic polarization tests. Biocompatibility assessments using PK15 cells showed a notable reduction in cell viability and metabolic activity, particularly with coatings of higher surface roughness. These findings underscore the need for improved surface preparation and coating processes to enhance adhesion and biocompatibility of rhenium-carbon coatings on Ti6Al4V substrates. Future research should focus on optimizing coating adhesion, investigating cytotoxicity mechanisms related to surface roughness, and expanding biocompatibility evaluations to various cell types and biological environments.

The deposition of dust particles on solar panel modules constitutes a significant challenge, leading to a potential reduction in solar cell performance. This work tackles this issue by investigating the surface modification of a layer of transparent indium tin oxide (ITO), with a detailed analysis of the influence of its characteristics via different annealing conditions/processing. The ITO layer has been studied to enhance its characteristics for dust removal applications. Of particular note is that the developed ITO layer can be applied to dust removal using electrostatic or magnetic-based approaches. Thus, the correlation between annealing gas (using Argon, Oxygen, and Nitrogen), annealing temperature, and annealing ramping rate is explored with the obtained surface topography, as well as electrical and optical properties. The developed ITO layers annealed in the Argon medium at 600°C with an annealing ramping rate of 50°C/s showed smooth surface roughness, the highest electrical conductivity, and a relatively low refractive index. Such findings can play a crucial role in the future implementation of using the enhanced ITO layer for dust mitigation in solar panels, thus improving their long-term performance.

This research investigates precision enhancement in regional quasi-geoid refinement through ADS80 tri-linear array scanning stereoscopic imagery for aerial triangulation, coupled with GNSS gravity-potential modeling. Acquiring stereoscopic imagery and analyzing triangulation accuracy with the ADS80 camera, we performed this study over the Qinghai-Tibet Plateau's elevated, desolate terrain, collecting 593 GNSS points following high-precision stereoscopic imagery model. Utilizing 12 gravity satellite models, we computed geoid heights and China 1985 Yellow Sea elevations for 28 benchmarks and GNSS points, thereby refining the Qinghai Province Quasi-Geoid Model (QPQM) using geometric techniques. The findings reveal that POS-assisted ADS80 stereoscopic imagery yields high-precision triangulation with maximal horizontal and elevation accuracies of 0.083/0.116 cm and 0.053/0.09 cm, respectively, across five control point arrangements. The RMSE of normal heights for 1985, processed via these GNSS points, achieved decimeter precision. By applying error corrections from benchmarks to the 1985 elevation data from gravity satellites and performing weighted averaging, the precision of EGM2008, SGG-UGM-2, and SGG-UGM-1 models improved to 8.61 cm, 9.09 cm, and 9.38 cm, respectively, surpassing the QPQM by 9.22 cm to 9.99 cm. This research demonstrates that the proposed methods can significantly enhance the precision of regional quasi-geoid surfaces. Additionally, these methods offer a novel approach for rapidly establishing regional quasi-geoid models in the uninhabited areas of the Qinghai-Tibet Plateau.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

Antibiotic-loaded bone cement (ALBC) plays a pivotal role in infection prevention and treatment related to musculoskeletal surgery. The release efficacy of antibiotics from ALBC is closely tied to its surface area, yet little is known about the effective release depth. To investigate the relationship between surface area, volume, and antibiotic elution, spheric ALBC specimens with consistent outer diameters but different internal metal sphere diameters were prepared. Two vancomycin doses were utilized in ALBC specimens with an outer diameter of 35 mm: high (4 g) and low (1 g). Each dosage group included five specimens containing embedded metal spheres with diameters of 15, 25, 29, 32, or 33 mm. The resulting shell-like ALBC specimens had thicknesses of 10 mm, 5 mm, 3 mm, 1.5 mm, or 1 mm, respectively. The specimens were immersed in sterile phosphate buffer solution, and antibiotic elution was measured at designated sampling times (1, 3, 6, 10, 24, 48, 72, and 168 hours). Methylene blue was employed to visualize penetration depth. Vancomycin elution did not display statistically significant differences between high- and low-dose groups. In both groups, specimens with 1 mm thickness exhibited a higher vancomycin release efficiency (high-dose group: 18560±5474 μg, 6.7%; low-dose group: 2017±419 μg, 2.6%), decreasing sharply in thicker ALBC specimens. Methylene blue penetration depth showed no apparent difference between high-dose and low-dose groups. ALBC thickness does not significantly impact antibiotic elution, while surface area and antibiotic dose exert notable effects. These in vitro findings offer potential applications in clinical treatments for musculoskeletal infections.

Broflanilide is a novel active ingredient from a unique insecticide class (IRAC Group 30) and was investigated as a control option against modern insecticide resistant strains of the common bed bug, Cimex lectularius. The susceptibility of technical grade broflanilide and efficacy of a broflanilide-based aerosol formulation (Earth Corp., Japan) were evaluated against five C. lectularius strains (MONH, SYD, DARL, PARRA, RIPPO). Results demonstrated that bed bugs had high susceptibility to broflanilide (RR50: SYD=1.22-fold, DARL=1.03-fold, PARRA=3.65-fold, RIPPO=2.77-fold), compared to the susceptible MONH strain. The aerosol showed high efficacy to adult bed bugs (97.5–100 % mortality to five strains after 24 hrs post-spray) and produced a notable decrease in egg hatch rates (MONH=9.7–23.4 %, PARRA=14.9–22.6 %). The aerosol also demonstrated high residual activity with 97.5–100% mortality in all five bed bug strains within 7 days exposure. The impact of different surface types upon aerosol residual efficacy was limited, although residues on a non-porous surface (tile) killed bed bugs slightly quicker than that on a porous surface (filter paper). The aerosol provided long residual activity to bed bugs, as 6-month-old residues were as equally efficacious to that of fresh residues. Bed bugs did not avoid surfaces treated with the aerosol. The high efficacy (including ovicidal efficacy), long residual activity, and non-avoidance of bed bugs on treated surfaces, demonstrated that broflanilide is highly suitable for modern bed bug management.

Alginate is naturally occurring polymer derived from brown algae biomass, which has found numerous applications in various fields. Chemical modification of alginate is widely used to improve the physicochemical properties of alginate and to provide new potential for various applications. In this article, we modified alginate with L-DOPA, using periodate oxidation and reductive amination, in order to be get more suitable biopolymer for biocatalysts immobilization and hydrogel formation. Obtained modified alginate was used for immobilization of laccase on cell walls. For this purpose, laccase from Streptomyces cyaneus was expressed on the surface of Saccharomyces cerevisiae EBY100 cells. Obtained cell wall laccase was immobilized within L-DOPA-alginate beads, by crosslinking of L-DOPA-alginate with calcium ions and laccase. The effect of additional crosslinking of beads by green light induced photopolymerization with eosin Y was investigated. The immobilized laccase systems were used for dye decolorization and also investigated in multiple treatment processes of dye decolorization. Beads with L-DOPA-alginate with higher degree of modification (5.0 mol%) showed higher enzymatic activity and better de-colorization efficiency compared to those with lower degree of modification (2.5 mol%). Obtained immobilized biocatalysts are suitable for the decolorization of dye Evans Blue due to their high efficiency and reusability.

Optical materials with a tunable localized surface plasmon resonance (LSPR) are of a great interest for applications in photonics and optoelectronics. In the present study we explored the potential of generating the LSPR band with an ultra-broad range of over 1000 nm in gold nanoparticles (NPs) precipitated through the thermal treatment in ZnO-Al2O3-SiO2 glass. Using the optical absorption spectroscopy, we demonstrated that the LSPR band's position and shape can be finely controlled by varying the thermal treatment route. Comprehensive methods including Raman spectroscopy, X-ray diffraction and high-resolution transmission electron microscopy were used to study the glass structure, while computational approaches were used for the theoretical description of the absorption spectra. Obtained results allowed us to suggest a scenario responsible for such abnormal LSPR band broadening which includes possible interparticle plasmonic coupling effect taking place during the liquid-liquid phase separation of the heat-treated glass. The formation of gold NPs with an ultra-broad LSPR band in glasses holds promise for sensitizing rare earth ion luminescence for new photonics devices.

With the emergence of autonomous functions in road vehicles, there has been an increased use of Advanced Driver Assistance Systems comprising various sensors to perform automated tasks. Light Detection and Ranging (LiDAR) is one of the most important types of optical sensor that detects the positions of obstacles, representing them as clusters of points in 3-dimensional space. LiDAR performance degrades significantly when driving in rain as raindrops adhere to the outer surface of the sensor assembly. The performance degradation behaviors include missing points and reduced reflectivity of the points. It was found that the extent of degradations is highly dependent on the interface material properties, which subsequently affects the shapes of the adherent droplets, causing different perturbations to the optical rays. A fundamental investigation is performed on the protective polycarbonate cover of the LiDAR assembly coated with four classes of materials – hydrophilic, almost-hydrophobic, hydrophobic, and superhydrophobic. Water droplets are controllably dispensed onto the cover to quantify the signal alteration due to each droplet of various sizes and shapes. To further understand the effects of droplet motion on LiDAR signals, sliding droplet conditions are simulated using numerical analysis and validated with physical optical tests using a 905 nm laser source and receiver to mimic the LiDAR detection mechanism. Comprehensive explanations are presented on LiDAR performance degradation in rain from both material and optical perspectives. These can aid component selection and the development of signal enhancing strategies for integrating LiDARs in vehicle designs to minimize the impact of rain.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

In order to improve the yield of the therapeutic agent N-methylsansalvamide (SA), optimization of stationary liquid fermentation conditions was carried out on an endophytic strain, Fusarium sp. R1, at flask level. Using a One-Factor-At-a-Time approach, the fermentation conditions for SA production were determined as follows: fermentation time of 13 d, 24 oC, initial pH of 6.5, seed age of 24 h, inoculum size of 5.0% (v/v), loading volume of 50% (v/v), 20.0 g/L salinity, and sucrose, tryptone, and yeast extract were found to be the best sources of carbon and nitrogen. Using response surface methodology, the optimal medium compositions consist of 22.5 g/L sucrose, 16.5 g/L tryptone, and 0.024 g/L yeast extract. Verification tests suggested that the SA yield under these optimal conditions reached up to 536.77 ± 2.67 mg/L, which was increased by almost ten times the initial yield (54.05 ± 3.45 mg/L). The findings indicate that a high SA production yield can be achieved by static culture of strain R1 under the proper fermentation conditions using a low-cost medium. This study paves the way towards industrial-scale SA production by strain R1 for new drug development.

Metal-catalyzed lipid oxidation is a major factor in food waste, as it reduces shelf life. Addressing this issue, our study investigates the potential of hydrolysates derived from potato protein, a by-product of potato starch production, as metal chelating antioxidants. Through sequential enzymatic hydrolysis using Alcalase or Trypsin combined with Flavourzyme, we produced various hydrolysates, which were then fractionated via ultrafiltration. Using a combination of peptidomics and bioinformatics, we predicted the presence of metal-chelating and free radical scavenging peptides across all hydrolysate fractions, with a trend indicating a higher content of antioxidant peptides in lower molecular weight fractions. To validate these predictions, we utilized Surface Plasmon Resonance (SPR) and a 9-day emulsion storage experiment. While SPR demonstrated potential in identifying antioxidant activity, it faced challenges in differentiating between hydrolysate fractions due to significant standard errors. In the storage experiment, all hydrolysates showed lipid oxidation inhibition, though not as effectively as EDTA. Remarkably, one fraction (AF13) was not significantly different (p < 0.05) from EDTA in suppressing hexanal formation. These results highlight SPR and peptidomics/bioinformatics as promising yet limited methods for antioxidant screening. Importantly, this study reveals the potential of potato protein hydrolysates as antioxidants in food products, warranting further research.

Explosive boiling is a fast phase transition from an ultra-thin liquid film to vapor under an extremely high heat flux, which typically has been studied using molecular dynamics simulation (MDS) method. The present MDS study investigated the explosive boiling of a liquid argon nanofilm over different solid copper surfaces with different nanowall patterns including parallel and cross nanowalls. For each surface, atomic motion trajectories, number of liquid and vapor argon atoms, heat flux, and, mainly, onset time of explosive boiling were investigated. The simulation results indicated that explosive boiling occurs earlier on parallel and cross nanowall surfaces than on an ideally smooth surface, regardless of the topology and configuration of nanowalls. Moreover, the results revealed that by using the cross nanowall surfaces, the onset time of explosive boiling decreased by 0.7–4% compared to the parallel nanowall surfaces. In addition, it was found that the onset time of explosive boiling strongly depends on the potential energy barrier and the movement space between nanowalls for both parallel and cross nanowall surfaces. Furthermore, simulation findings showed that even though increasing the height of cross nanowalls increases heat flux and temperature of the fluid argon domain, it does not necessarily result in a shorter onset time of explosive boiling. These findings demonstrate the capability of cross nanowall surfaces for explosive boiling, thereby could be utilized in future surface design for thermal management applications.

Surfactants are widely used in the synthesis of nanoparticles, as they have a remarkable ability to direct their growth to obtain well-defined shapes and sizes. However, their post-synthesis removal is a challenge, and the methods used often result in morphological changes that defeat the purpose of the initial controlled growth. The cleaning methods could be classified as thermal or non-thermal. In general, the structure of materials can be better preserved by non-thermal treatments. After the removal of surfactants, the highly active surfaces of nanomaterials may undergo structural reconstruction by exposure to a different environment. Thus, ex situ characterization after air exposure may not reflect the effect of the cleaning methods. In situ characterization is required to better understand the impact of various cleaning procedures. Combining X-ray photoelectron spectroscopy, in situ infrared reflection absorption spectroscopy, and environmental transmission electron microscopy measurements with CO probe experiments, we investigated different surfactant-removal methods to produce clean metallic Pt nanoparticles from surfactant-encapsulated ones. Non-thermal plasmas show the best results. It was demonstrated that both UV-ozone treatment and room temperature O2 plasma treatment lead to the formation of Pt oxides on the surface after the removal of the surfactant. These oxides are reduced to metallic Pt during in situ CO probe experiments. On the other hand, when H2 was used for plasma treatment, the Pt0 oxidation state and nanoparticle size distribution were preserved. In addition, H2 plasma treatment can reduce Pt oxides after O2-based treatments, resulting in metallic nanoparticles with clean surfaces. Thermal reduction in hydrogen leads to carbon species emerging onto nanoparticle surfaces after heating and agglomeration of Pt nanoparticles. Particularly, O2-based thermal treatments result in the formation of aggregates consisting of small nanoparticles. These findings provide a better understanding of the various options for surfactant removal from metal nanoparticles and point toward non-thermal plasmas as the best route if the integrity of the nanoparticle needs to be preserved.

Increased CO2 emissions and air pollution impact the environment and human health. In this manner, new functionalized polyaminal-based polymers are synthesized via a one-pot polycondensation reaction of melamine with aldehyde monomers 2-bromo-1-naphthaldehyde and 2-hydroxy-1-naphthaldehyde to yield bromine- hydroxyl- functionalized polymer networks PAN-BrNA and PAN-HNA, respectively. The polyaminals porosity parameters were investigated and applied as an adsorbent for CO2 capture. FTIR, solid-state 13C NMR, and X-ray diffraction verified the PANs structure development. A scanning electron microscope and N2 adsorption-desorption methods were utilized to identify the porous properties of the polymers at 77 K. The Brunauer-Emmett-Teller (BET) surface area of PAN-BrNA and PAN-HNA is (16.6990 m2/g) and (716.7568 m2/g), respectively. At 273 K, PAN-BrNA and PAN-HNA can take CO2 gas up to (4.42786 cm3/g) and (47.55 cm3/g), respectively. The findings show that inserting functional groups has a significant impact on surface area and porosity parameters, as well as CO2 uptake.

The identified Urban Heat Island (UHI) phenomenon, coupled with diminished vegetation and anthropogenic heat release, poses a significant environmental challenge for major urban centers. Particularly worrisome is the UHI effect in hot and temperate climates such as the Mediterranean region during the summer season. This exacerbates discomfort and heightens the risks of diseases linked to high temperatures. Additionally, it contributes to environmental consequences, including elevated electricity consumption due to increased demand for cooling [1]. The utilization of Remotely Sensed imagery for estimating Land Surface Temperature has become more prevalent in various applications associated with evaluating urban micro-climates and the Urban Heat Island (UHI) phenomenon. This study presents an algorithm for the automatic mapping of Land Surface Temperature (LST) from Landsat-8 data using a vegetation index-based technique in the Google Earth Engine (GEE) platform. The primary aim is to discern patterns and trends in LST over a 5-year period, from 2017 to 2021. The application was tested in the urban area of Thessaloniki, Northern Greece, which is particularly representative of the Mediterranean urban environment. Computation of Normalized Difference Indices (NDVI, NDBI, NDWI) for the study area was also performed within the GEE platform and correlation analysis was implemented to evaluate the impact of the urban landscape on the distribution of LST.

Global climate change has induced a rise in sea surface temperature (SST), although this increase is not uniform across the world. Significant variations exist between coastal and offshore waters, particularly in regions affected by upwelling processes. This study focuses on the Canary Current Upwelling System (CCUS), stretching from Northwest Iberia to Northwest Africa. High-resolution remotely sensed SST data (0.05°) from the ODYSSEA Level 4 Sea Surface Temperature Reprocessed dataset were validated with in-situ measurements and employed to establish a regional climatological baseline for 1982 – 2012. Subsequent years were compared to this baseline to construct SST anomaly maps, revealing SST changes since 2012. The study area was further divided into sub-regions for comparative analysis. Results indicate that SST consistently increased at a higher rate offshore compared to the adjacent nearshore regions. A reference dataset spanning 1951 – 1981 was used to gauge SST variability between the two baselines. SST exhibited a 0.59°C increase from 1951 – 1981 to 1982 – 2012, with a slowing of SST trends beyond the 1982 – 2012 baseline. This research offers valuable insights into the climatological dynamics of the CCUS. These findings enhance our understanding of this critical coastal system's climatology, laying the groundwork for future investigations into evolving climate patterns in coastal regions.

The surface electromyogram (sEMG)--based gesture recognition to the development of intelligent prostheses has emerged as a promising avenue for upper limb amputees. However, the temporal variations in sEMG have rendered recognition models less efficient than anticipated. Cross-session calibration and training data indicate the capacity to reduce this variation. The impact of varying calibration and training data amounts on gesture recognition performance for amputees is still unknown. To assess these effects, we present four datasets for the evaluation of calibration data and examine the impact of training data volume on benchmark performance. Two amputees who had undergone amputations years prior were recruited and seven sessions of data were collected for analysis from each of them. The experimental results show that the calibration data improved the average accuracy per subject by 3.03% and 6.16%, respectively, compared to the baseline results. Moreover, it was found that to collect training data for modeling, boosting the number of training sessions proves more efficient than increasing the number of trials within a single session. Two potentially effective strategies are proposed in light of this research to enhance the cross-session models further. We consider these findings to be of the utmost importance for the commercialization of intelligent prostheses, as they demonstrate the criticality of gathering calibration and cross-session training data, as well as offer effective strategies for maximizing the utilization of the entire dataset.

Cathode materials play a key role in the development and application of lithium-ion batteries, but the unfavorable factors such as structural phase transformation and low conductivity in the cycling process restrict the further improvement of battery performance, so the development and modification of high-performance cathode materials is a current research hotspot. LiNixCoyMn1-x-yO2(x≥0.6), a high-nickel cathode material, has the advantages of high platform potential, high energy density and low cost, and is an ideal material to achieve the goal of 300 Wh kg-1 and above for batteries. However, its poor thermal stability, poor interface stability, safety and life cannot meet the requirements of current power batteries. In this paper, the research status of high-nickel cathode materials is introduced, including bulk doping and surface coating, and the modification method of doping and coating integration is also introduced. Finally, we put forward the prospect of the future development trend of high-nickel cathode materials.

To study the fermentation process of biocatalyzing decanoic acid to synthesize trans-2-decenoic acid, this study was based on the engineering E.coli constructed in the laboratory in the early stage and studied the effect of seed liquid culture time, culture temperature, inoculum amount, induction temperature, dissolution effects of substrate solvent, metal ions, and substrate loading on the yield of trans-2-decenoic acid. Based on single-factor experimental optimization, the Box–Behnken design was used to conduct response surface testing using the substrate feeding concentration, inducer concentration, and MnCl2 concentration as response variables and trans-2-decenoic acid production as the response value. The optimal fermentation process was determined through experiments: seed culture time 20 h, culture temperature 37°C, inoculation amount 1%, induction temperature 30°C, substrate flow amount 0.15 g/L, inducer concentration 5.60 g/L, MnCl2 concentration was 0.10 mM. Under these conditions, the average production of trans-2-decenoic acid was 1.982 ± 0.110 g/L. Compared with the basic LB medium, the production of trans-2-decenoic acid increased by 1.042 g/L; compared with the previous period, the yield of trans-2-decenoic acid studied increased by 1.501 ± 0.110 g/L, which provides a reliable basis for further research on the fermentation process of biocatalytic decanoic acid synthesis of trans-2-decenoic acid.

Statistical analysis of mechanical properties of thin-walled samples (~500 microns) obtained by selective laser melting from AlSi10Mg material and subjected to heat treatment for 1 hour at temperatures from 260 °C to 440 °C (step of aging temperature change 30 °C) has shown that the maximum strain hardening in the stretching diagram section from yield strength to tensile strength is achieved at the heat treatment temperature equal to 290 °C. At carrying out of correlation analysis statistically significant positive correlation between deformation corresponding to yield strength and the sum of heights of the largest protrusions and depths of the largest depressions of the surface roughness profile within the basic length of the sample (Rz) and the full height of the surface roughness profile (Rmax) was established. It was found that the reason for the correlation is the presence of cohesive states between the extreme values of the surface roughness profile that persist along the entire length of the specimen.

The resonance spectrum of surface resistance derivative in quasi-two dimensional layered organic conductors has been calculated numerically for the out-of-plane and in-plane magnetic field. Not all but some of the resonances in a given series of transitions are present in the spectra. They are observed at the positions corresponding to the maxima in the surface resistance derivative curve and are in a good agreement with previously calculated magnetic field resonance positions. For tilted magnetic fields, there are more resonances present in the spectrum than in the case of a non-tilted field. Apart from the resonances corresponding to the transitions between the adjacent surface states there also appear resonances involving the transitions between the more distant surface states. This is correlated with the specific topology of Fermi surface of the organic conductors. The presented calculations will allow correct interpretation of the experimental curves for the resonance spectrum, and also to obtain information on the surface properties of these materials for their possible implementation in fabrication of devices based on organic molecular conductors.

The motion of Unmanned Surface Vehicles (USVs) is frequently disturbed by the ocean wind, wave and current. A poorly designed controller will lead to failures and even safety problems during actual navigation. In order to obtain satisfied control performance of the motion for the USVs, a Model Predictive Control (MPC) based on improved Nonlinear Disturbance Observer (NDO) is proposed. Firstly, the USV model is approximately linearized and MPC is designed for the multivariable system with constraints. In order to compensate the influence of disturbances, an improved NDO is designed, with which the calculation time for the MPC saved a lot. Finally, comparison experiments are conducted between the MPC with NDO and the MPC with improved NDO, and the results show that they have similar performance to the USVs. However, the proposed method has less parameter to be tuned and it is much more time-saving compared to the MPC with traditional NDO.

PDMS samples may be used in various microfluidic applications by hydrophilizing their surfaces. This study examines the effects of air plasma jet (APJ) and dielectric barrier discharge (DBD) plasma on the surface hydrophilicity of polydimethylsiloxane. In order to increase the hydrophilicity of PDMS sample surfaces, two plasma sources including APJ and DBD were compared. Both DBD and APJ setups were measured for voltage and current, and their respective power was calculated and compared based on their characteristics. It is important to note that the electrical specifications of APJ and DBD were identical, and the source power rates for APJ and DBD plasma were 306W and 300W respectively. UV-vis spectroscopy was used to characterize the plasma, and an electrical characterization of the plasma's power supply was carried out. The effects of parameters such as the distance from the nozzle tip, the duration of the process, and the source voltage on the hydrophilicity of the surfaces during the treatment by APJ were also examined, and samples were then examined for a period of time to determine whether surface hydrophilicity was preserved. On the PDMS surface, a contact angle of about 5.1° was observed using short-term plasma treatments of 10 seconds. In the same conditions, the effect of DBD treatment was superior to that of APJ treatment.

This research focuses on monitoring the spatiotemporal changes of urban surface water in Dhaka City from 1990 to 2021, utilizing satellite imagery and the Google Earth Engine (GEE) platform. Surface water is essential for urban, environmental, and agricultural ecosystems, and its dynamics have significant implications for water resource planning and environmental management. The main objectives of this study are to assess the extent of urban surface water coverage over the last three decades and identify trends of water loss or gain in the study area. The study employs Landsat 5 TM and Landsat 8 OLI/TIRS imagery, integrating GEE with machine learning coding and WRI techniques to extract and analyze surface water data efficiently. Traditional remote sensing methods for dynamic monitoring are time-consuming and cumbersome, but GEE offers a user-friendly and accurate approach, providing easy access to satellite data and cloud-based processing. The results reveal a concerning trend in urban surface water coverage, indicating a significant reduction from 36.23 km² in 1990 to 5.83 km² in 2021, representing a loss of approximately 20 square kilometers or 45 percent of surface water over the last three decades. The decline is attributed to factors such as unplanned urban expansion, rapid real estate development, and increased industrial and economic activities in the study area. The developed algorithms utilizing GEE offer valuable insights into the maximum and minimum extent of surface water, enabling effective surface water planning and management. These findings contribute to sustainable water resource management and environmental preservation in Dhaka City.

Basic mechanisms of laser interaction with synthetic diamond are reviewed. The features of the major regimes of diamond surface etching are considered. Besides well-known graphitization and ablation processes, the nanoablation and accumulative graphitization, which attracted the attention relatively recently, are described in detail. The focus is placed on femtosecond (fs) laser exposure which provides a formation of dense cold electron-hole plasma in focal zone and a minimum overheating in surrounding area. This potentially opens the way to develop unique laser-based technologies combining physical and chemical processes for precise surface treatment and functionalization. The physical limitations determining how precisely the diamond surface can be treated by short-pulsed laser radiation and possible pathways to overcome them with the end to remove ultra-thin layers of the material are discussed. Particular attention is devoted to the novel possibility to induce local formation of point active defects - nitrogen vacancy (NV) complexes in the laser-irradiated zone. Both the regimes of NV centers generation with and without graphitization of diamond lattice are reviewed. It is thus shown that intensive pulse laser radiation is a perfect tool for processing of synthetic diamonds on the micro, nano and even on an atomic level that can be well controlled and managed.

Trypanosomes are the extracellular protozoan parasites that cause human African trypanosomiasis disease in humans and nagana disease in animals. The disease is endemic in African countries where tsetse flies which act as a vector for the transmission of disease are present. The animals infected by these parasites become useless or workless and disease can become fatal if not treated. Old drugs used for treatment have many side effects and some are responsible for death in 5% of the patients. The parasite possesses a major surface protein known as variant surface glycoprotein. The immune system of the host develops antibodies against this antigen but due to antigenic variation, parasites evade the immune response. Currently, no vaccine is available that provides complete protection. Only partial protection using certain antigens in murine models was investigated. The tools of molecular biology and immunology have enabled a novel approach to the development of vaccines against trypanosomes. Immunization is the sole method for the control of disease because the eradication of the vector from endemic areas is an impossible task. Genetic vaccines can carry multiple genes encoding different antigens of the same parasite or different parasites. DNA immunization induces the activation of both cellular immune response and humoral immune response along with the generation of memory. This review highlights the importance of DNA vaccines and advances in the development of DNA vaccines against T. brucei.

In the Mediterranean area, vegetation dynamics and phenology analyzed over a long time can have an important role in highlighting changes in land use and cover as well as the effect of climate change. Over the last 30 years, remote sensing has played an essential role in bringing about these changes thanks to many types of observations and techniques. Satellite images are to be considered an important tool to grasp these dynamics and evaluate them in an inexpensive and multidisciplinary way thanks to Landsat and Sentinel satellite constellations. The integration of these tools holds a dual potential: on one hand, allowing to obtain longer historical series of reflectance data, while on the other hand, making data available with a higher frequency even within a specific timeframe. The study aims to conduct a comprehensive cross-comparison analysis of long-time series pixel values in the Mediterranean regions. For this scope comparisons between Landsat-7 (ETM+), Landsat-8 (OLI), and Sentinel-2 (MSI) satellite sensors were conducted based on surface reflectance products. We evaluated these differences using Ordinary Least Squares (OLS) and Major Axis linear regression (RMA) analysis on points extracted from over 15,000 images across the Mediterranean basin area from 2017 to 2020. Minor but consistent differences were noted, necessitating the formulation of suitable adjustment equations to better align Sentinel-2 reflectance values with those of Landsat-7 or Landsat-8. The results of the analysis are compared with the most used harmonization coefficients proposed in the literature, revealing significant differences. The root mean square deviation, the mean difference and the orthogonal distance regression (ODR) slope show an improvement of the parameters for both models used (OLS and RMA) in this study. The discrepancies in reflectance values lead to corresponding variations in the estimation of biophysical parameters, such as NDVI, showing an increase in the ODR slope of 0.3. Despite differences in spatial, spectral, and temporal characteristics, we demonstrate that integration of these datasets is feasible through the application of band-wise regression corrections for a sensitive and heterogeneous area like those of the Mediterranean basin area.

We have much to learn from historic buildings. The fact that they are still standing is obvious, but unfortunately often not appreciated. In this paper the results obtained from a series of parametric analyses, where the influence that geometric and mechanical parameters have in the structural response of existing cob walls within an Irish context, are presented. A design of experiments using central composite designs was implemented along with analysis of variance following two computational approaches, namely, finite element method and kinematic limit analysis. As results, a series of response surfaces and parametric equations with which it is possible to compute safety factors and collapse multipliers (within the range of values studied) are provided. Based on the results obtained, it could be concluded that traditional cob walls in Ireland are very robust. Relatively high acceleration values, unlikely to happen in a low seismic hazard region such as Ireland, would be needed to start the collapse mechanisms studied or cause yielding in typical vernacular cob walls. Furthermore, the equations generated with the refined regression models, can be used by practitioners as a first approach to estimate the safety levels of existing cob buildings with similar characteristics.

High surface area carbon was obtained from -carrageenan – urea cryogels doped with 1.25 – 5 wt% graphene oxide (GO). Incorporation of GO resulted in multifaceted modification in the textural and chemical properties of the carbon cryogel. The thermal decomposition of GO facilitated the formation of micropores resulted in a substantial increase in the apparent surface area (up to 1780 m2/g). The annealing at 1000 °C removed part of the heteroatoms but left behind a high number of defects. While the volatile thermal degradation products of GO affected the porous texture and the surface chemistry in a complex way, its reduced residue resulted in a gradually increasing electrical conductivity. The influence of GO was studied in oxygen reduction reaction (ORR) and in Li-ion storage application. GO affected the electron transfer mechanism in the ORR tests and challenged the stability of the electrodes. Even if the electrode has been stabilized under oxygen-free conditions, later may undergo destabilization processes during the ORR. The 5 wt% GO doped sample was the most sensitive under oxidative conditions, but finally it exhibited the highest capacitance. In the Li-ion battery tests the coulombic efficiency of all the samples was consistently above 98 %, indicating the great potential of such carbons for efficient Li-ion insertion and reinsertion during the charge – discharge process, thereby providing a promising alternative for graphite-based anodes. The cell from the 1.25% sample showed an initial discharge capacity of 313 mAh/g, 95.1 % capacity retention and 99.3 % coulombic efficiency after 50 charge – discharge cycles.

Silicon anodes have been considered one of the most promising anode candidates for the next generation of high-energy density lithium-ion batteries due to the high theoretical specific capacity (4200 mAh g-1) of Si. However, high lithiation capacity endows silicon anodes with severe volume expansion effects during the charge/discharge cycling. The repeated volume expansions not only lead to the pulverization of silicon particles and the separation of electrode materials from the current collector, but also brings rupture/formation of solid electrolyte interface (SEI) and also continuous electrolyte consumption, which seriously hinders the commercial application of silicon anodes. Structural design and optimization is the key to improving the electrochemical performances of silicon anodes, which has attracted wide attention and research in recent years. This paper mainly summarizes and compares the latest research progress for the structural design and optimization of silicon anodes.

Ultra-high temperature oxidation-resistant alloys (UTORAs) have received a lot of attention due to the increased research demand for deep space exploration around the world. But UTORAs have the disadvantages of easy oxidation and chalking. So, in this study, a UTORA was prepared by hot-press sintering on VZrHfNbTa (HEA) substrate coated with hafnium. The bonding mechanism, resistance to high-temperature oxidation, and hardness of the sample tests were carried out. The results show that zirconium in the matrix will diffuse into the hafnium coating during the high-temperature sintering process and form the HfZr alloy transition layer, the coating thickness of the composite is about 120 μm, and the diffusion distance of zirconium in the hafnium coating is about 60 μm, this transition layer chemically combines the hafnium coating and the HEA substrate into a monolithic alloy composite. The results of high-temperature oxidation experiments show that the oxidation degree of the hafnium-coated VZrHfNbTa composite material was significantly lower than that of the VZrHfNbTa HEA after oxidation in air at 1600 °C for 5 h. The weight gain of the coated sample after oxidation is 56.56 mg/cm2, which was only 57.7 % compared to the weight gain of the uncoated sample (98.09 mg/cm2 for uncoated), and the surface of the uncoated HEA showed obvious dents, oxidation, and pulverization occurred on the surface and interior of the sample. In contrast, the coated composite alloy sample mainly underwent surface oxidation sintering to form a dense HfO2 protective layer, and the internal oxidation of the hafnium-coated VZrHfNbTa composite alloy was significantly lower than that of the uncoated VZrHfNbTa HEA.

Objective: The purpose of this study was to evaluate the surface texture and biofilm adhesion of veneered or CAD/CAM milled zirconia (partially stabilized with yttrium) after professional oral hygiene procedures. Samples (4x4 mm, thickness 2 mm; n = 72) were separated from zirconia blanks (3Y-TZP-LA). One group was veenired with ceramics and the other group of samples was CAD/CAM milled. Each group had 2 subgroups: polished and glazed. The samples were subjected to simulated strokes of professional brushing using abrasive paste and ultrasonic scaling. Parameters of surface micromorphology and receptivity to biofilm were calculated before and after simulating the given methods of professional maintenance of oral hygiene. The characteristics of zirconia surface were evaluated by scanning electron microscopy (SEM). Microbial bacterial/fungal species (Staphylococcus aureus, Streptococcus sanguinis and Candida albicans) were used and cultured on the respective sterilized zirconia surfaces. The amount of biofilm formation on zirconia surface was quantified by colony forming unit (CFU) counts. Results: SEM analysis showed the greatest change in surface microtopography after the use of ultrasonic scaling, in glazed zirconia samples. Less formation of colonies on the surface CAD/CAM milled zirconia restorations was observed. Conclusion: Routine methods of professional maintenance of oral hygiene can damage the surface of glazed zirconia restorations.

This paper investigates the effect of shot peening on the strength and corrosion properties of EN AW 6082-T651 aluminium alloy. Surface roughness, microhardness, residual stresses and corrosion performance were investigated and compared with the untreated aluminium alloy. Cracks and delaminations in the surface layer can only be seen on the treated specimens at a working pressure of 4 bar and 8 bar, while no such effect was observed at a working pressure of 1.6 bar. The effect of dislocation densification was confirmed by the microhardness measurement of the hardened layer, where microhardness increased by up to 23 % compared to the untreated aluminium alloy. Shot peening also results in a deeper layer with higher compressive residual stresses compared to untreated specimens. With higher working pressure, surface roughness increases, which can promote localized pitting corrosion. However, all treated specimens improve the corrosion resistance and have a lower degree of anodic dissolution. The current density of the shot peened specimen with the lowest surface roughness was more than twice lower than that of the untreated specimen.

Surface defect detection is a crucial step in the process of automotive wheel production. However, the task possesses challenges due to complex background and a wide range of defect types. In order to detect the defects on the wheel surface accurately and quickly, this paper proposes a YOLOv5-based algorithm for automotive wheel surface defect detection. The algorithm trains and tests the YOLOv5s model using the self-created automotive wheel surface defect dataset, which contains four kinds of defects: linear, dotted, sludge, pinhole. The extensive experimental results demonstrate that the deep learning network trained by our method can achieve an average accuracy of 71.7% and 57.14 FPS. Our findings prove that this detection algorithm performs better than other common target detection algorithms and meets the real-time requirements of industrial applications.

Total bilateral Limbal Stem Cells Deficiency is a pathologic condition of the ocular surface due to the loss of corneal stem cells. Cultivated Oral Mucosa Epithelial Transplantation (COMET) is the only autologous successful treatment for this pathology in clinical application, although non-physiological peripheric corneal vascularization often occurs. Properly characterizing the regenerated ocular surface is needed for a reliable follow-up. So far, the univocal identification of transplanted oral mucosa had been challenging. Previously proposed markers were shown co-expressed by the different ocular surface epithelia in a homeostatic or perturbated environment. In this study, we compared the transcriptome profile of human oral mucosa, limbal and conjunctival cells, identifying PITX2 as a new marker that univocally distinguishes the transplanted oral tissue from the other epithelia. We validated PITX2 at RNA and protein levels to investigate 10-year follow-up cor-neal samples derived from a COMET-treated aniridic patient. Moreover, we found novel angiogenesis-related factors differentially expressed in the three epithelia and instrumental in explaining the neovascularization in COMET-treated patients. These results will support the follow-up analysis of patients transplanted with oral mucosa and provide new tools to understand the regeneration mechanism of the transplanted cornea.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

Skid resistance of a road pavement surface is the force developed when tyre is prevented from rotating slides along the pavement sur-face. This property comes from the combination of the macro- and micro-texture of pavement. The skid resistance of an asphalt pave-ment is an important parameter influencing driving safety on a road, since there is a proven relationship between skid resistance and accident parameters. The paper deals with the measurement principle of pavement skid resistance (surface friction) including longitudinal and transverse friction. A high number of measuring devices of skid resist-ance are also introduced highlighting their advantages and limitations. Besides, the measurement policies in the European Union and in Hun-gary are outlined. Pavement surface texture is investigated dealing with the levels of surface tex-ture, the most common measuring tech-niques, the macro-texture features of asphalt types, as well as the Hungarian regulation in the field. As a related topic, the aggregate properties and their implication in the relevant Hungarian specification are introduced briefly, as well. Some outcomes of the EU’s COST Ac-tion 354 on the development of unified European macro-roughness and skid resistance performance indicators and indices are also presented.

The surface defects of shield subway tunnel can significantly affect the serviceability of the tunnel structure and may compromise the operation safety. To effectively detect the multiple surface defects, this research employs a tunnel inspection trolley (TIT) based on the mobile laser scanning technique. By conducting the inspection of the shield tunnel on a metro line section, various surface defects are identified by the TIT, including water leakage defect, dislocation, spalling, cross-section deformation, etc. To explore the root causes of the surface defects, the association rules between different defects are calculated via an improved Apriori algorithm. Results show that: i) there are significant differences in different association rules of various surface defects of the shield tunnel; ii) the average confidence of the association rule “dislocation &amp; spalling → water leakage” is as high as 57.78%, indicating that most of the water leakage defects are caused by dislocation and spalling of the shield tunnel in the sections being inspected; iii) the weakest rule appears at “water leakage → spalling”, with the average confidence of 13%. The association analysis can be used in predicting the critical defects influencing the structural reliability and operation safety, such as water leakage, and optimizing the construction and maintenance work for the shield subway tunnel.

The presence of copper in distilled sugar cane spirits, especially cachaça produced in alembics, has impeded the marketing of this product. Red mud (RM) is a residue obtained from alumina production. It contains a high concentration of metal oxides and is very alkaline. The RM was dried at 100 oC and sifted through a 150-micron sieve. The sample was characterized by B.E.T. nitrogen adsorption, scanning electron microscopy-energy-dispersive X-ray (SEM-EDX) and Atomic Absorption Spectrometry (A.A.S.). The textural parameters indicate that the total surface area (S.T.) was 21.9 m2g-1, and the total volume pore (V.T.) was 0.09 cm3g-1. The RM (1 g) was stirred for two hours with a 1.0 L cachaça sample containing 9.39 mg of copper L-1 and filtered under atmospheric pressure. The concentration of copper ions detected in the filtrate was 0.00 mg L-1. No copper ions were retained when the cachaça was filtered through the RM under high pressure without stirring prior to filtration.

In the recent years, biochar has emerged as a remarkable biosourced material for addressing global environmental, agricultural, biomedical, and energy challenges. However, the performances of biochar rest in part on finely tuning its surface chemical properties, intended to obtain specific functionalities. In this review, we tackle surface treatment of biochar with silane and other coupling agents such as diazonium salts, titatantes, ionic/non-ionic surfactants, as well as nitrogen-containing (macro)molecules. We summarize the recent progress achieved mostly in the last five years, and correlate the nature and extent of functionalization to eye catchy end applications of the surface engineered biochar.

Mesenchymal stem cells (MSCs) have the tumor-homing capacity, and therefore MSCs are considered to be a promising drug delivery carrier for cancer therapy. To maintain the viability and activity of MSCs, anti-cancer drugs are preferably modified on the surface of MSCs, rather than directly introduced into MSCs. In this study, we attempted to construct surface-modified MSCs with liposomes as a drug carrier by using magnetic anionic liposome/atelocollagen complexes we previously developed. We observed that large-sized magnetic anionic liposome/atelocollagen complexes were abundantly associated with MSCs via electrostatic interactions under a magnetic field, and its cellular internalization was lower than that of the small-sized complexes. Moreover, the complexes with higher atelocollagen concentration showed lower cellular internalization than the complexes with lower atelocollagen concentration. Based on these results, we succeeded in the efficient surface modification of MSCs with liposome by using large-sized magnetic anionic liposomes complexed with high concentration of atelocollagen. The constructed liposome-modified MSCs showed comparable proliferation rate and differentiation potential to unmodified MSCs. Furthermore, liposome-modified MSCs efficiently adhered to vascular endothelial cells and migrated toward the conditioned medium from cancer cells in vitro. These findings suggest that liposome-modified MSCs could serve as an efficient cell-based drug carrier for tumor targeted delivery.

Inspired by Dirac's large number hypothesis (LNH), Zeldovich proposed a relation between the cosmological constant (CC), the mass of a proton, the Planck constant and Newton's gravitational constant. Zeldovich's formula suggests that the substance which is responsible for CC may interact with elementary particles. Since Newton's gravitational constant and the Planck constant appear in Zeldovich's formula, these interactions may be related to gravitational phenomena and quantum phenomena. Following this clue, we propose a liquid droplet model of electron. Applying the Laplace's equation, Zeldovich's formula of CC is derived. Weinberg proposes a relation between the mass of a pion, the Planck constant, the Hubble constant, Newton's gravitational constant and the velocity of light in vacuum when discussing cosmological models with a varying constant of gravitation. Weinberg pointed out that this relation may not merely be regarded as a meaningless random combinations of these fundamental constants in physics. The Weinberg's relation is derived based on the critical mass density formula in the Friedmann model of the universe and Zeldovich's formula.

Sea surface salinity (SSS) is one of the Essential Climate Variables (ECVs) as defined by the Global Climate Observing System (GCOS). Acquiring high-quality SSS datasets with high spatial-temporal resolution is cruicial for research on the hydrological cycle and earth climate. This study assessed the quality of SSS data provided by four high-resolution ocean reanalysis products, including the Hybrid Coordinate Ocean Model (HYCOM) 1/12° global reanalysis, the The Copernicus Global 1/12° Oceanic and Sea Ice GLORYS12 Reanal-ysis, the Simple Ocean Data Assimilation (SODA) reanalysis, the ECMWF Oceanic Reanalysis System 5 (ORAS5) product and the Estimating the Circulation and Climate of the Ocean Phase II (ECCO2) reanalysis. Regional comparison in the Mediterranean Sea shows that reanalysis largely depicts the accurate spatial SSS structure away from river mouths and coastal areas but slightly underestimates the mean SSS values. Better SSS reanalysis performance is found in the Levantine Sea while larger SSS uncertainties are found in the Adriatic Sea and the Aegean Sea. The global comparison with CMEMS level-4 (L4) SSS show generally con-sistent large-scale structures. The mean ΔSSS between monthly gridded reanalysis data and in situ analyzed data is -0.1 PSU in the open seas between 40°S and 40°N with the mean Root Mean Square Deviation (RMSD) generally smaller than 0.3 PSU and the majority of correlation coefficients higher than 0.5. Comparison with collocated buoy salinity shows that reanalysis products well captures the SSS variations at the locations of tropical moored buoy arrays at weekly scale. Among all the four products, the data quality of HYCOM re-analysis SSS is highest in marginal sea, GLORYS12 has the best performance in the global ocean especially in tropical regions. Comparatively, ECCO2 has the overall worst performance to reproduce SSS states and variations by showing the largest discrepancies with CMEMS L4 SSS.

Electron beam treatment of ZnS:Cu,Br (Cu activator content 0…0.6%wt.) radioluminescent phosphors as well as charge mixture with the electron energy 900 keV and absorbed dose of 600 kGy resulted in a enhancement of brightness up to 80%. The increased brightness is due to increase of content of wurtzite phase relative to sphalerite one with formation of wurtzite/sphalerite nanocomposite structure. Transformation of crystal structure is accompanied with corresponding change in content of active surface centers characteristic for sphalerite and wurtzite phases. A model describing surface centers of ZnS:Cu,Br radioluminescent phosphor is suggested.

Fringe projection profilometry(FPP) has been extensively applied in various fields for its superior fast speed, high accuracy and high data density. However, measuring some objects with high reflective surfaces or high dynamic range surfaces remains challenging for FPP. Some multiple exposure image fusion methods have been proposed and successfully improved the measurement performance for these kinds of objects. Normally, these methods have a relatively fixed sequence of exposure settings determined by artificial experience or trial and error experiments, which may decrease the efficiency of the entire measurement process and may have less robustness to various environmental lighting conditions and object reflective properties. In this paper, a novel self-adaptive multiple exposure image fusion method is proposed with two main aspects of improvement on adaptively optimizing the initial exposure and the exposure sequence. By introducing the theory of information entropy, combined with the analysis of the characterization of fringe image entropy, an adaptive initial exposure searching method is first proposed. Then, an exposure sequence generation method based on dichotomy is further described. On the base of these two improvements, a novel self-adaptive multiple exposure image fusion method for FPP as well as its detailed procedures are given. Experimental results validate the performance of the proposed self-adaptivity multiple exposure image fusion method by measuring the objects with different surface reflectivity and in different ambient lighting conditions.

Thin films of BiFeO3 (BFO), VO2 and BFO/VO2 were grown on SrTiO3(100) and Al2O3(0001) monocrystalline substrates using the RF and DC sputtering techniques. The surface of the films was characterized by profilometry, AFM, and XPS. The heterostructures have roughnesses between 0.2 and 16 nm and a grain size between 20 nm and 67 nm. XPS measurements show a higher proportion of the V4+ and Bi3+ oxides. In the Fe region, a higher proportion of Fe3+ is shown in the films. The homogeneous ordering, low roughnesses, and the oxidation states on the obtained surface show a good coupling in these films. The I-V curves show ohmic behavior at room temperature and change with increasing temperature. The effect of coupling these materials in a thin film shows the appearance of hysteresis cycles I-V and R-T, typical of materials with high potential in applications such as resistive memories and solar cells.

This paper presents an algorithm for the fully automatic mesh generation for the finite element analysis of ships and offshore structures. The quality requirements on the mesh generator are imposed by the acceptance criteria of the classification societies as well as the need to avoid shear locking when using low degree shell elements. The meshing algorithm will be generating quadrilateral dominated meshes (consisting of quads and triangles) and the mesh quality requirements mandate that quadrilaterals with internal angles close to $90\degree$ are to be preferred. The geometry is described by a dictionary containing points, rods, surfaces and openings. The first part of the proposed method consist of an algorithm to automatically clean the geometry. The corrected geometry is then meshed by the frontal Delaunay mesh generator as implemented in the gmsh package. We present a heuristic method to precondition the cross field of the frontal quadrilateral mesher. Also the influence of the order in which the plates are meshed will be explored as a preconditioning step.

In this paper, an all-fiber Mach-Zehnder interferometer (MZI) sensor for refractive index (RI) measuring is presented, which is based on Multimode–Single-mode–Multimode (MSM) fiber. The effects of both reducing the radius of the sensing part and the surface plasmon resonance (SPR) on its efficiency are investigated. Increasing the interaction of high-order modes with external media, caused by etching the cladding layer of the single-mode fiber part, significantly improves the sensitivity. Both wavelength and intensity interrogation approaches are employed to study the Multimode–etched Single-mode–Multimode (MESM) fiber sensor. The intensity and the wavelength sensitivities for the RI measurement in the range of 1.428-1.458 are obtained as -2308.92 %/RIU and 1313.14 nm/RIU, respectively. Finally, the MESM-SPR sensor is proposed and characterized. Results exhibit high performance in the RI range of 1.333 to 1.357, in which the sensitivity of 1433 nm/RIU is achieved. The advantages like low cost, high sensitivity, and simple fabrication methods make these sensors promising devices for chemical, food industry, and biosensing applications.

Mangrove vegetation plays a vital role in habitat and nursing ground for different organisms and prevents coastal erosion caused by wave and tide action. In recent years the mangrove vegetation in Chattogram coast, Bangladesh, has been interrupted by other infrastructural development, which has a destructing effect on the surrounding environment. Land surface temperature analysis of an area helps learn about different environmental conditions, weather, and climate. It is also essential to monitor the rising temperature and global warming, the biggest threat to humanity. NDBI and NDVI are the efficient process for monitoring vegetation and build up areas of a geographical location. This study focused on those analyses to understand the importance of mangrove vegetation in the Salimpur area and surrounding coastal areas of Chattogram by studying the relationship between NDVI and NDBI, NDVI and LST, NDBI, and LST. The outcome indicates that a higher vegetation index results in lower land surface temperature during different periods, negatively correlated. This study also found a strong positive correlation between buildup index (NDBI) and land surface temperature (LST), which means Land Surface temperature was found higher in Buildup areas. The vegetation areas are greatly affected by the buildup areas. The correlation between buildup areas and vegetation areas was strongly negative, which means an increase of NDBI decreases NDVI, and a decrease of NDBI increases NDVI.

The design of processing routes involving the presence of the liquid phase is mainly associated with the knowledge of its surface and transport properties. Despite this need, due to experimental difficulties related to high temperature measurements of metallic melts, for many alloy systems neither thermodynamic nor thermophysical properties data are available. A good example lacking these datasets represents the Ir-Si system, although over the last fifty years, the structures and properties of its solid phases have been widely investigated. To compensate the missing data, the Gibbs free energy of mixing of the Ir-Si liquid phase was calculated combining the model predicted values for the enthalpy and entropy of mixing using Miedema’s model and Free Volume Theory, respectively. Subsequently, in the framework of statistical mechanics and thermodynamics, the surface properties were calculated using the Quasi Chemical Approximation (QCA) for the regular solution, while to obtain the viscosity, the Moelwyn-Hughes (MH) and Terzieff models were applied. Subsequently, the predicted values of the abovementioned thermophysical properties were used to model the non-reactive infiltration isotherm of Ir-Si (eutectic) / SiC system.

Sediment plumes, released to the Bering Sea from the delta front of the Yukon River, Alaska, are initiated mainly by glacier-melt sediment runoffs in the glacierized regions of the Yukon River drainage basin. The surface sediment plumes are extended around the fan-shaped Yukon River delta, which is followed by the northwestward dispersion. During continuous measure-ments of the Yukon River discharge and sediment load, behaviors of the sediment plumes were explored by shipboard observations in the Bering Sea offshore from the Yukon delta. At the high river sediment load of ca. 3000 kg/s, the plume partially plunged into the sea bottom layer. The plunging probably originated in the nepheloid-layer formation from the flocculation of river-suspended sediment, of which more than 90 %wt. is silt and clay (grain size d < 0.063 mm). In order to numerically obtain the area of the surface sediment plumes, a satellite image analy-sis was performed by using three near-infrared bands in MODIS/Aqua or MODIS/Terra. The plume area was significantly correlated (R2=0.735, p<0.01) to the sediment load averaged for the two days with time lags of 20 days and 21 days to the date of a certain satellite image. Hence, the dispersion of plume-suspended sediment appears to be controlled by the sediment runoff events in the Yukon River rather than the northward “Alaskan Coastal Water”.