The ubiquitous connectivity for the space-air-ground integrated network (SAGIN) of the beyond fifth generation of communication and sixth generation of communication (B5G/6G) is envisaged to meet the needs for the demanded quality of service (QoS), green communication, and "dual carbon" target. However, the offloading and computation of massive latency-sensitive tasks dramatically increases the energy consumption of the network. Furthermore, the traditional power supply technology of the network base stations (BSs) enhances the carbon emission. To address these issues, we first propose a SAGIN architecture with energy harvesting devices, where the BS is powered by both renewable energy (RE) and the conventional grid. The BS explores wireless power transfer (WPT) technology to power the unmanned aerial vehicle (UAV) for stable network operation. RE sharing between neighbouring BSs is designed to fully utilize RE for reduce carbon emission. Secondly, on the basis of task offloading decision, UAV trajectory, and RE sharing ratio, we construct cost functions with joint latency-oriented, energy consumption, and carbon emission. Then, we develop a twin delayed deep deterministic policy gradient (TD3PG) algorithm based on deep reinforcement learning to minimize the cost function. Finally, simulation results demonstrate that the proposed algorithm outperforms the benchmark algorithm in terms of reducing latency, energy saving, and lower carbon emission.

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

Gwadar is essential for Pakistan's financial stability. The third deep-water port in Pakistan, Gwadar, plays a significant part in trade between the Gulf countries, Africa, China, United Arab Emirates, and Cordillera Administrative Region. However, the load Shedding of 12-16 hours in Gwadar is the most concerning issue. Pakistan imports 70 MW of electricity from Iran. The wind and solar system are already installed but for a limited residential area. In Gwadar, there are enough renewable energy resources that can be utilized for electricity generation. In this context, a Techno and Economic Analysis is performed using the Hybrid Optimization Model for Multiple Energy Resources (HOMER) Pro. Two models are considered for this study. Model-1 includes PV/Wind Turbine/ and Battery while Model-2 consists of PV/Wind Turbine/Converter and Grid. The yearly energy generated by Model-1 and Model-2 is 57.37 GWh and 81.5 GWh, respectively. The levelized cost of electricity (LCOE) for Model-1 and Model-2 is respectively $0.401/kWh and $0.0347/kWh. It is shown that the simple payback of Model-1 is of 6.70 years, and the simple payback of Model-2 is 7.77 years. Due to the high LCOE of Model-1, its payback year is lesser than model-2. All of these facts indicate that Model 2 is the most optimal solution.

AAs the global energy market undergoes a wholesale transformation accelerated by the need to decarbonise, a rapid transition to renewable energy and the mass deployment of distributed energy resources, autonomous energy networks or microgrids are emerging as an attractive mechanism for the delivery of electricity to end users. Yet in Australia, at least, relatively little is known about key aspects of microgrids that are fundamental to their successful deployment, not least the more commercial and economic elements rather than the purely technical. Drawing on the extant global literature on microgrids, this paper explores the most important of these aspects including business models, ownership and investment. Identifying the ambiguity, inconsistency and uncertainty evident in many of the feasibility studies currently in train across Australia, this paper highlights specific areas for future research that need to be addressed if the full potential of microgrids is to be realised in the context of a global energy transition both domestically and internationally.

The residential sector in the United States is in need of comprehensive policy-making reforms that concurrently address housing affordability and environmental sustainability. This study investigates the feasibility of state-wide zero-energy affordable housing by analyzing historical data on climate, energy use, and solar system costs in the Commonwealth of Virginia. The hypothesis examined is that the net present cost of implementation of rooftop residential solar systems to achieve zero-energy Low-Income Housing Tax Credit (LIHTC) buildings is lower than the discounted present cost of energy of otherwise identical conventional buildings that run without renewable energy generation systems. The authors propose a generalizable framework for analyzing the feasibility of achieving region- or state-wide zero-energy LIHTC developments. To validate the framework, the authors employ a longitudinal sample of monthly energy use data from 2013-2016 obtained from 310 residential units of 15 LIHTC developments across the state. Based on statistical regression analysis, energy simulation, and simulation-based risk analysis, the authors find that the net present value of zero-energy LIHTC investments can be positive with a low risk. The investment value varies often depending on the zero-energy building definition, weather characteristics, retail price of electricity, and incentive rate. This study can help housing policymakers and industry professionals analyze and benchmark the feasibility of innovative zero-energy housing policies and projects.

Global waste generation keeps increasing over the year and requires innovative solutions to minimize their impacts on environmental quality and public health. Predicted 2.2 billion tonnes per year of global municipal waste generation in the year 2025 which 1.6 fold is higher than in 2012. Hence, a strategic plan must be ascertained to overcome the future challenges of MSW locally and globally. Universiti Putra Malaysia (UPM) coined an initiative to demonstrate a showcase pilot plant for green energy production from MSW. Therefore, the data was obtained from the survey and actual sampling within the UPM compound to estimate the MSW generated and it's potentially used for green energy production. It is estimated that 5.0 – 7.0 tonne per day of MSW generated which about 30 - 35% is an organic fraction. Upon separation, the organic fractions were digested into biogas through anaerobic. At the maximum conversion of organic fraction, about 775 kWh of electricity may able to generate from the waste. In this study, the complete biorefinery setup and utilize organic components from the MSW generated in UPM was proposed that the biogas subsequently will be used to produce green energy in the form of electricity or cooking fuel.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

In previous papers we have derived equations of motion with radiation terms and proved the existence-uniqueness of periodic solution of the 3-body problem of classical electrodynamics. The number of equations of motion – 12 is more than the number of unknown functions – 9. It turns out that 9 equations are independent and the rest 3 ones are consequences of them. These three equations have a solution and they give the expressions for the energy of the moving particles. The main goal of the present paper is to estimate the energy of rounding about the nuclei particles and compare it with the values given by quantum mechanics.

Incorporating renewables in the power grid presents challenges for stability, reliability, and operational efficiency. Integrating Energy Storage Systems (ESS) offers a solution by managing unpredictable loads, enhancing reliability, and serving the grid. Hybrid storage solutions have gained attention for specific applications, suggesting higher performance in some respects. This paper compares the performance of hybrid energy storage systems (HESS) to single battery, evaluating their energy supply cost and environmental impact through optimization problems. The model generates an optimized dispatch, minimizing cost or environmental impact of supplying energy to a generic load while considering battery degradation. Seven technologies are assessed, with an example applied to an industrial site contrasting vanadium redox flow (VRFB) and lithium batteries considering the demand of a local load (building). The results also indicates that efficiency and degradation curves have the highest impact in the final costs and environmental functions on the various storage technologies assessed. For the simulations of the example case, a single system only outperforms the hybrid system in cases where lithium efficiency is higher than approximately 87% and vanadium is lower approximately 82%.

Observation of the distribution of the velocity of galactic rotation curves differed from their expected centripetal form and lead to the notion of Dark Matter or modifications to Newtonian and General Relativity, such as MOND, TeVeS and the like and even Quantised Inertia. We aim to show that General Relativity with Dark Energy/the Cosmological Constant is all that is needed, with the proviso that the Cosmological Constant can increase in the presence of a gravitational field and become gravitating to account for the hypothesis of Dark Matter Haloes.

Energy efficiency considerations in terms of reduced power dissipation is a significant issue in the design of digital circuits for very large-scale integration (VLSI) systems. Quantum-dot cellular automata (QCA) is an emerging ultra-low power dissipation approach, distinct from the traditional complementary metal-oxide semiconductor (CMOS) technology, for building digital computing circuits. Developing fully reversible QCA circuits has the potential to significantly reduce energy dissipation. The multiplexer is a fundamental element in the construction of useful digital circuits. In this paper, a novel, multilayer, fully reversible QCA 8:1 multiplexer circuit, with ultralow energy dissipation, is introduced. The proposed multiplexer power dissipation is simulated using the QCADesigner-E version 2.2 tool, describing the microscopic physical mechanisms underlying the QCA operation. The results showed that the proposed reversible QCA 8:1 multiplexer consumes 89% less energy than the most energy-efficient 8:1 multiplexer circuit presented previously in the scientific literature.

As part of the Earth Climate Observatory space mission concept for the direct observation from space of the Earth Energy Imbalance, we propose an advanced camera suite for the high resolution observation of the Total Outgoing Radiation of the Earth. For the observation of the Reflected Solar Radiation, we propose the use of two multispectral cameras covering the range from 400 to 950 nm, with a nadir resolution of 1.7 km, combined with a high resolution RGB camera, with a nadir resolution of 0.57 km. For the observation of the Outgoing Longwave Radiation, we propose the use of 6 microbolometer cameras, with each a spectral bandwidth of 1 μm in the range from 8 to 14 μm, and with a nadir resolution of 2.2 km.

The transportation sector is a significant source of greenhouse gas emissions. Electric vehicles (EVs) have gained popularity as a solution to reduce emissions, but the high load of charging stations poses a challenge to the power grid. Nuclear-Renewable Hybrid Energy Systems (N-RHES) present a promising alternative to support fast charging stations, reduce grid dependency, and decrease emissions. However, the intermittent problem of renewable energy sources (RESs) limits their application, and the synergies among different technologies have not been fully exploited. This paper proposes a predictive and adaptive control strategy to optimize the energy management of N-RHES for fast charging stations, considering the integration of nuclear, photovoltaics, and wind turbine energy with a hydrogen storage fuel cell system. The proposed dynamic model of a fast-charging station predicts electricity consumption behavior during charging processes, generating probabilistic forecasting of electricity consumption time-series profiling. Key performance indicators and sensitivity analyses illustrate the practicability of the suggested system, which offers a comprehensive solution to provide reliable, sustainable, and low-emission energy to fast-charging stations while reducing emissions and dependency on the power grid.

The Unmanned Aerial Vehicles (UAVs), used in civilian applications such as emergency medical deliveries, precision agriculture, wireless communication provisioning, etc., face the challenge of limited flight time due to their reliance on the on-board battery. Therefore, developing efficient mechanisms for in-situ power transfer to recharge UAV batteries hold potential in extending their mission time. In this paper, we study the use of far-field wireless power transfer (WPT) technique from specialized, transmitter UAVs (tUAVs) carrying Multiple Input Multiple Output (MIMO) antennas for transferring wireless power to receiver UAVs (rUAVs) in a mission. The tUAVs can fly and adjust their distance to the rUAVs to maximize energy transfer. The use of MIMO antennas further boost the energy reception by narrowing the energy beam toward the rUAVs. The complexity of their dynamic operating environment increases with the growing number of tUAVs, and rUAVs with varying levels of energy consumption and residual power. We propose an intelligent trajectory selection algorithm for the tUAVs based on a deep reinforcement learning model called Proximal Policy Optimization (PPO) to optimize the energy transfer gain. Simulation results demonstrate that with the use of PPO, the system achieves a tenfold flight time extension compared to no wireless recharging. Further, PPO outperforms the benchmark movement strategies of ’Traveling Salesman Problem’ and ’Low Battery First’ when used by the tUAVs.

It is proposed that both human creativity and human consciousness are (unintended) consequences of the human brain’s extraordinary energy efficiency. The topics of creativity and consciousness are treated separately, though have a common sub-structure. It is argued that creativity arises from a synergy between two cognitive modes of the human brain (which broadly coincide with Kahneman’s Systems 1 and 2). In the first, available energy is spread across a relatively large network of neurons. As such, the amount of energy per active neuron is so small that the operation of such neurons is susceptible to thermal (ultimately quantum decoherent) noise. In the second, available energy is focussed on a small enough subset of neurons to guarantee a deterministic operation. An illustration of how this synergy can lead to creativity with implications for computing in silicon are discussed. Starting with a discussion of the concept of free will, the notion of consciousness is defined in terms of an awareness of what are perceived to be nearby counterfactual worlds in state space. It is argued that such awareness arises from an interplay between our memories on the one hand, and quantum physical mechanisms (where, unlike in classical physics, nearby counterfactual worlds play an indispensable dynamical role) in the ion channels of neural networks. As with the brain’s susceptibility to noise, it is argued that in situations where quantum physics plays a role in the brain, it does so for reasons of energy efficiency. As an illustration of this definition of consciousness, a novel proposal is outlined as to why quantum entanglement appears so counter-intuitive.

Smart cities and smart technologies have been incorporated into several axes to increase the comfort of life. The connected building's concept was introduced for this reason. However, it was utilized in power management for better organizing, greater buildings management, and monetary savings. Cars technologies and the number of vehicles are also involved; Nowadays, each house has at least one car. Technological evolution helped to make those cars intelligent and connected. In the latest versions, the majority of those cars were equipped with several sensors, several communication protocols and a principal electrical control unit (ECU), especially for the electric vehicle model. This type of architecture was an essential element in a smart city, thus, it helps to manage power and decide when a vehicle needs to be charged. Based on the smart city concept and using possible network communication between buildings and vehicles, EVs can share their own information related to the powerful experience on a specific path. This information can be gathered in a gigantic database and used for managing the power inside these vehicles. In this field, we propose in this paper a new approach for power management inside an electric vehicle based on bi-communication between vehicles and buildings. The proposed approach is founded on two essential parts; the first is related to vehicles’ classification and buildings’ recommendation according to different car positions. Two algorithms, related to the SVC and neural network was employed in this work for implementing the final process. Different possibilities and situations were discussed for this approach. The proposed method was tested and validated using Simulink/Matlab application. The state of charge of the used battery was compared at the end of this work, for two specified cases, for showing the contribution of this approach.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

In this paper we re-investigated the relationship between the symmetry of inertial systems and the Lorentz transformation. We found that when we just follow the following three principles: (1)we can define the time in the whole space with a prescribed clock synchronization, (2)the time-space is uniform and the space is isotropic and (3)all the inertial systems are equivalent, then we can totally construct a general coordinate transformation to meet the symmetry of inertial systems, and with a special assumption on the speed of light, we can construct a non-Lorentz transformation between inertial systems to make the particle’s energy have a limited value, which is similar to the rainbow model. Similar to the usual Lorentz violating models, the non-Lorentz transformation in this paper lead to a new modified disperse relation. We applied the obtained disperse relation to analyze the photon’s arrival time lag effect in astronomy and found that the "maximum energy" derived in our model is somewhat related to the "maximum energy" assumed in the rainbow model.

In this paper, the linear nonequilibrium thermodynamic approach is used to analyze energy processes in the wind energy conversion system (WECS), with a directly connected vertical axis wind turbine (VAWT) and vector controlled permanent magnet synchronous generator (PMSG). Both elements are considered as linear universal energy converters (EC) linearized at the points of the given range of common to VAWT and PMSG angular velocity. The dependences on the angular velocity of the coupling coefficients between the ECs input and output and the dimensionless parameters of their operating modes were received. This allows for choosing the optimal points of ECs operation according to the specified criteria and obtaining indicators of their maximum efficiency. To assess the quality of the cascade connection of two ECs, the appropriate coefficient was introduced, the dimensionless parameters and characteristics of the equivalent EC were obtained, and the conditions of its maximum efficiency were determined. Analysis of the VAWT-PMSG connection quality showed reserves for improving WECS efficiency. The impact of VAWT and PMSG variable parameters on the quality of this connection is studied, and further research directions are shown. The proposed thermodynamic approach allows an effective search for solutions for the efficiency improvement of various systems with energy transfer and transformation.

We present a modified version of the Szilard Engine, demonstrating that an explicit measurement procedure is entirely unnecessary for its operation. By considering our modified engine, we are able to provide a new interpretation of Landauer’s original argument for the cost of erasure. From this view, we demonstrate that a reset operation is strictly impossible in a dynamical system with only conservative forces. Then, we prove that to approach a reset yields an unavoidable instability at the reset point. Finally, we present an original proof of Landauer’s principle that is completely independent from the Second Law of Thermodynamics.

Recent astronomical observations with respect to measurements in distant supernovas, cosmic microwave background and weak gravitational lensing confirm that the Universe is undergoing a phase of accelerated expansion and it has been proposed that this cosmological behavior is caused by a hypothetical dark energy which has a strong negative pressure that allows explain the expanding universe. Several theoretical ideas and models related dark the energy includes the cosmological constant, quintessence, Chaplygin gas, braneworld and tachyonic scalar fields. In this paper, we have obtained new relativistic stellar configurations considering an anisotropic fluid distribution with a charge distribution which could represents a potential model of a dark energy star. In order to investigate the effect of a quadratic equation of state in this anisotropic model we specify particular forms for the gravitational potential that allow solving the Einstein-Maxwell field equations. For these new solutions we checked that the radial pressure, metric coefficients, energy density, anisotropy factor, charge density , mass function are well defined and are regular in the interior of the star. The solutions found can be used in the development of dark energy stars models satisfying all physical acceptability conditions but the causality condition and strong energy condition are violated. We expect that these models have multiple applications in astrophysics and cosmology.

The article is focused mainly on verifying the suitability of data from experimental milling heat-treated beech wood and on investigation of the effect of technical and technological parameters of milling on the energy consumption of this process. The independent parameters of machining process are cutting speed, feed speed, rake angle, and hydrothermal modification of experimental wood material. Based on analysis of variance it can be argued that the greatest statistically significant effect on energy consumption have cutting speed and rake angle of the tool while the feed speed had the least influence. The measured data of cutting power during milling were used to build a regression model and validate it, while the most suitable type of model with correlation of 87 % is Classification and Regression Tree followed by model created by Random Forests method.

Dual-energy CT (DECT) imaging has broadened the potential of CT imaging by offering multiple postprocessing datasets with a single acquisition at more than one energy level. DECT shows profound capabilities to improve diagnosis based on its superior material differentiation and its quantitative value. However, the potential of dual energy imaging remains relatively untapped, possibly due to its intricate workflow and intrinsic technical limitations of DECT. Knowing the clinical advantages of dual-energy imaging and recognizing its limitations and pitfalls is neces-sary for an appropriate clinical use. The aims of this paper are to review physical and technical basis of DECT acquisition and analysis, to discuss advantages and limitations of DECT in dif-ferent clinical scenarios, to review technical constraints in material labeling and quantification, and to evaluate cutting-edge applications of DECT imaging, including artificial intelligence, qualitative and quantitative imaging biomarkers, and DECT-derived radiomics and radioge-nomics

Designing the future energy supply in accordance with ambitious climate change mitigation goals is a challenging issue. Common tools for planning and calculating future investments in renewable and sustainable technologies are often linear energy system models based on cost optimisation. However, input data and the underlying assumptions of future developments are subject to uncertainties that negatively affect the robustness of results. This paper introduces a quadratic programming approach to modifying linear, bottom-up energy system optimisation models in order to take cost uncertainties into account. This is accomplished by implementing specific investment costs as a function of the installed capacity of each technology. In contrast to established approaches like stochastic programming or Monte Carlo Simulation, the computation time of the quadratic programming approach is only slightly higher than that of linear programming. The model’s outcomes were found to show a wider range as well as a more robust allocation of the considered technologies than the linear model equivalent.

Accurately predicting the power of solar power generation can greatly reduce the impact of the randomness and volatility of power generation on the stability of the power grid system, which is beneficial for the balanced operation and optimized dispatch of the power grid system, and reduces operating costs. Solar PV power generation depends on weather conditions, which are prone to large fluctuations under different weather conditions. Its power generation is characterized by randomness, volatility and intermittency. Recently, the demand for further investigation and effective use on the uncertainty of short-term solar PV power generation prediction has been getting increasing attention in many application of renewable energy sources. In order to improve the predictive accuracy of output power of solar PV power generation and develop a precise predictive model, the authors worked predictive algorithms for the output power of a solar PV power generation system. Moreover, since short-term solar PV power forecasting is one of the important aspects for optimizing the operation and control of renewable energy systems and electricity markets, this review focuses on the predictive models of solar PV power generation, which can be verified in the daily planning and operation of a smart grid system. In addition, the predictive methods in the reviewed literature are classified according to the input data source used for accurate predictive models, and the case studies and examples proposed are analyzed in detail. The contributions, advantages and disadvantages of the predictive probabilistic methods are compared. Finally, the future studies of short-term solar PV power forecasting is proposed.

This study utilizes a regional numerical weather model incorporating multilayer urban canopy parameterization alongside a building energy model (BEP + BEM) to examine the sensitivity of various urban parameters, including those defining urban materials and building environments, during a real-case heatwave event in the Chicago Metropolitan Area (CMA) in August 2023. The application of local climate zones further refines this analysis. Findings indicate that wall conductivity and ground albedo play significant roles in affecting urban near-surface temperatures. Conversely, alterations in other urban parameters are found to exert minimal influence on near-surface temperatures throughout the heatwave. In terms of building energy consumption, the selection of the target indoor temperature emerges as a pivotal factor. While adjustments in ventilation rates also bear considerable effects, other variables appear to have a subdued impact on energy usage. Additionally, the marginal effect of wall emissivity on energy consumption highlights the intricate balance between different heat transfer mechanisms and the adaptive capacity of building heating and cooling systems.

The world is currently facing an energy crisis. To solve the problem, many countries have been exploring renewable energy sources. However, the existing renewable energy sources are highly dependent on weather changes, necessitating the utilization of significantly expensive and large storage batteries.As a solution, we propose a system for generating renewable energy. The proposed system comprises a current source and a voltage source connected in series. With appropriate adjustments, the current source supplies current without voltage and the voltage source provides voltage without current. Considering that electric power is a product of current and voltage, electric power is generated from the interaction between the current source and voltage source. In our previous study, the same result was obtained; however, the output voltage was low, which resulted in a low amount of generated energy. In this study, by introducing some ingenuities, we successfully increased the output voltage. Consequently, we succeeded in powering a light-emitting diode and charging a super-condenser to the standard voltage. Using this system, we generated a relatively large amount of energy in the right place and at the right time, validating our systems’ robustness to changes in weather. The large-scale adoption of our system could contribute to solving the global energy crisis.

Swarm electrification-driven communities face significant challenges, including implementing advanced distributed control in areas with limited ICT access and establishing trust among villagers hesitant to grant access to their assets. This paper proposes a distributed DC microgrid architecture for P2P energy exchange in these communities, ensuring stability and effective exchange operation. By implementing a Blockchain marketplace specifically designed to suit the rural context, the proposed architecture ensures tracing of exchange transactions to fairly settle participants. Validation experiments demonstrate its efficacy in achieving peak shaving. It provides 11% of the requester's total demand from the community even while maintaining the constraint of reducing discharge-charge cycles to one per day, thereby preserving battery life. Additionally, the solution reduces prosumer production losses by 16% of the total PV production.

At nuclear scale, we present three heuristic relations pertaining to strong and electroweak coupling constants. With these relations, close to beta stability line, it is possible to study nuclear binding energy with a single energy coefficient of magnitude $\left(\frac{1}{{\alpha }_s}\right)\left[\frac{e^2}{4\pi {\epsilon }_0{R}_0}\right]\approx 10.0\text{MeV}\text{.}$ With reference to up and down quark masses, it is also possible to interpret that, nuclear binding energy is proportional to the mean mass of $\left[\left(2m_u+m_d\right)\text{and}\left(m_u+2m_d\right)\right]\approx 10.0\text{MeV}.$

We calculate energies of shallow donors confined in a rolled-up quantum well in the presence of the electric field by solving numerically the Schrödinger equation in natural curvilinear coordinates. It is found that the curves of density of states (DOS) are very sensitive to the variation of the donor position, the geometry of the spiral and the applied electric field value. Novel results for dependencies of donor’s dipole moment and its polarizability on the electric field strength and its orientation, for different donor positions are presented. Also, we found that anisotropic Stark effect of the first order provides in this structure a dependency of the polarizability on the external electric field in a spike-like shape, giving rise to a sharp variation of the dipole moment.

Developments in artificial intelligence techniques allow for an improvement in sustainable mobility strategies with particular reference to energy consumption estimates of electric vehicles (EVs). This research proposes a vehicle energy model developed on the basis of Deep Neural Network (DNN) technology. The study also explores the potential application of the model developed for the movement data of new vehicles in the province of Enna, Sicily, Italy. which is characterized by numerous attractors and the increasing number of hybrid and electric cars circulating. The energy model for electric vehicles shows high accuracy and versatility, requiring vehicle velocity and acceleration as input data to predict energy consumption. The research article also provides recommendations for the energy modeling of electric vehicles and outlines additional steps for model development. The implemented methodological approach and its results can be used by transport decision makers to plan new transport policies in Italian cities aimed at optimizing vehicle charging infrastructure. They can also help vehicle users accurately estimate energy consumption, generate maps, and identify locations with the highest energy consumption.

This research paper aims to evaluate and model the performance of rice husk gasifier cook stoves for household energy use, a byproduct of rice milling. The study aims to address environmental issues and promote the use of rice husk as a renewable energy source and pest repellent in stoves. The study compared insulated and non-insulated gasifier stoves using rice husk gasification. The study compared the start-up time of insulated and non-insulated gasifier stoves, where the insulated stove showed a lower start-up time, but there was no significant difference at a 5% probability level. The temperature change also was not significant, as heat transfer and temperature change started when the husk was ignited. The burner stoves had different size and volume. The maximum operated or flame temperature was 1,190.30oC at room or minimum temperature of 27.33 oC, whereas the average temperature was 758.916oC for the non-insulated type of gasifier stove. The insulated gasifier stove also observed maximum and average temperatures of 518.30 oC and 289.014oC respectively at the same room temperature. The operating time of stoves directly influences the fuel consumption rate, specific gasification rate, and combustion zone rate of stoves. The fuel consumption rate has a significant effect on the type of gasifier stove, with the maximum rates being 3.820 and 2.099 kg/hr. The time to consume rice husks to gasify them depends on the density of the rice husk, reactor volume, and fuel consumption rate. The average specific gasification rate for insulated and non-insulated stoves is 106.45 and 120.63 kg/m2h, respectively. The fuel or rice husk holding capacity of each type of stove is significant at a 5% level, with the amount of rice husk and biochar produced being 1.18kg and 0.27kg for insulated stoves, and 2.511kg and 0.688kg for non-insulated stoves, respectively. The performance of gasifier stoves varies based on the bio char conversion rate, with non-insulated stoves producing a higher bio char mass per rice husk. Multiple regression analysis was used to model the relationship between time elapse with temperature and heat energy. The Squirrel-2020 data logger was used to measure the temperature produced by burning rice husks in the reactor of the stove as well as related generated and losses of heat. A relationship between the heat energy produced and the operating time of gasifier stoves was conducted to estimate the model. The cubic polynomial model was found to be the best predictive model fit for all variables of this study.

In the transition towards sustainable energy sources, hydrogen has emerged as the predominant alternative after fossil fuels. This comprehensive literature review delves into the evolving landscape of hydrogen launching strategies within the energy market. Numerous countries have strategically initiated efforts to introduce products based on hydrogen, underscoring the global acknowledgment of the potential inherent in hydrogen. Despite witnessing significant growth in the adoption of hydrogen energy worldwide, impediments to its widespread commercialization persist. This review identifies key barriers, including cost structures, technical complexities, and marketing challenges, hindering the establishment of a robust hydrogen energy market. The article critically examines the actions already undertaken to harness hydrogen energy for commercial purposes, leveraging scientific insights and statistical data. By carefully examining the current state of hydrogen energy initiatives, the review highlights gaps in existing strategies that require thoughtful consideration. Insights derived from scientific and statistical analyses inform the identification of barriers and contribute to a nuanced understanding of the challenges faced in the journey towards hydrogen energy commercialization. Ultimately, the article presents a strategic proposal outlining marketing actions geared towards expediting the commercialization and widespread adoption of hydrogen energy. Grounded in a thorough review of existing literature and supported by scientific and statistical evidence, this comprehensive analysis offers valuable insights for stakeholders seeking to navigate the intricate landscape of hydrogen energy in the global energy market.

Background: The proportion of dietary protein may play a key role in the development of obesity in children and adolescents. Methods: Cross-sectional data of 4,336 children and adolescents from the National Health and Nutrition Survey (NHANES) during 2011 to March 2020 were analyzed. Multivariate logistic regression analysis was used to estimate odds ratios (OR) and 95% confidence intervals, and restriction cubic spline was uesd to explore nonlinear relationships of dietary protein energy supply ratio and obesity in children and adolescents. Results:In the adjusted logistic regression model, for every 1% increase in dietary protein energy ratio in children and adolescents, the increased risk of obesity was 4% (OR=1.04,95%CI:1.01-1.08). The restrictive cubic spline showed a nonlinear relationship between dietary protein energy ratio and obesity in children aged 6-11 years (P <0.05). The dietary protein energy supply ratio was included in the logistic regression model after converting to quartiles into categorical variables. The adjusted OR of children aged 6-11 years was 2.08 (95%CI:1.34, 3.23,P <0.01) for the highest quartile of dietary protein energy supply ratio compared with the lowest quartile. Conclusion: In American children, dietary protein energy supply ratios was positively correlated with obesity, independent of individual characteristics and energy.

The very slow anodic oxygen evolution reaction (OER) greatly limits the development of large-scale hydrogen production via water electrolysis. By replacing OER with easier urea oxidation reaction (UOR), developing a HER/UOR coupling electrolysis system for hydrogen production can significantly save energy and costs. Al doped cobalt ferrocyanide (Al-Co2Fe(CN)6) nanocube array was in-situ grown on nickel foam (Al-Co2Fe(CN)6/NF). Due to the unique nanocube array structure and regulated electronic structure of Al-Co2Fe(CN)6, the as-prepared Al-Co2Fe(CN)6/NF electrode exhibited outstanding catalytic activities and long-term stability to both UOR and HER. The Al-Co2Fe(CN)6/NF electrode needed potentials of 0.169 V and 1.118 V (vs. reversible hydrogen electrode) to drive 10 mA cm−2 for HER and UOR, respectively, in alkaline condition. Applying the Al-Co2Fe(CN)6/NF to a whole urea electrolysis system, 10 mA cm−2 was achieved at a cell voltage of 1.357 V, which saved 60% electricity energy comparing to that of tranditional water splitting. Density functional theory calculations demonstrated that the boosted UOR activity comes from Co sites with Al doped electronic environments. This promoted and balanced the adsorption/desorption of main intermediates in UOR process. This work indicates that Co based materials as efficient catalysts have great prospects for application in urea electrolysis systems, and are expected to achieve low-cost and energy-saving H2 production.

This paper analyses the EU’s policies for energy and climate, using Börzel's (2002) theoretical framework on Europeanisation, and examines member states’ Green Deal responses, strategies, and compliance. As expressed in their final NECPs, although member states’ responses vary, most of the critical components were partially addressed, while the others were largely addressed. We observe a considerable variation in Member State’s strategies. Member States classified as foot-dragging beforehand are fence-sitting now, while those previously categorised as fence-sitting are now either foot-dragging or pace-setting. The root cause of these classification changes for the member states within the EU can be traced back to their internal environments in which the involved stakeholders each have a different response pace regarding environment, climate, and energy. We present and analyse our theoretical context, discuss the EU’s energy policies and the NECPs, examine member states’ responses and compliance with this new framework, and propose several challenges.

This research project focuses on the optimization of the hybrid energy system together with the assistance of thin-film coatings aiming to achieve self-sustainable food and crop storage facilities which will run effectively with its own generated energy. An infrastructure will be designed and constructed that will comprise a hybrid power generation system accompanied by thin-film coated semitransparent and non-transparent construction materials for energy saving. Thin-film low emissivity (Low-E) type coatings will assist the transparent or semitransparent construction materials to reflect most of the infrared (IR-mostly heat) and UV spectra of sunlight without interrupting the visible spectrum and will lead to saving energy consumption by reducing the heat and lighting during day time

Analyses of the Environmental Kuznet's Curve (EKC) hypothesis have largely focused on economy level data with occasional analyses exploring sector level data. This paper exploits a new data set which contains sector level data on greenhouse gas emissions from the US energy sector as well as subsector data from six disjoint subsectors which together comprise the entire energy sector. The data contained in this data set is annual data at the state level from 1990 through 2011. By using differenced data we specify an econometrically sound EKC model and compare it against a model containing only a linear GDP per capita term. We find that by using a subsector level modelling approach, evidence for the EKC hypothesis is virtually nonexistent. Moreover, we find that aggregated subsector level estimates outperform sector level estimate on in-sample accuracy. These estimated models are then used to forecast emissions for the energy sector. We find evidence that US greenhouse gas emissions from energy production are at or near a peak.

The purpose of this paper is to test the Kuznets Environmental Curve (KEC) hypothesis for 10 MENA (Middle East and North Africa) countries during the period 1987-2017. To do this, the translogical functional form has been adopted to estimate the relationship between Toxic Gases (TG) emissions, energy consumption and GDP per capita. The results confirm the presence of KEC, GDP per capita and energy consumption have a positive influence on TG emissions, and the presence of a feedback relationship between GDP per capita and energy consumption. As a result, the environmental framework of the selected countries improves as their level of growth has become more advanced. In addition, to reduce TG emissions, MENA countries are expected to significantly increase the use of renewable energy and a more efficient energy policy.

In the context of the development of bioprocesses for the production of biofuels and bulk chemicals, microbial cells are rationally engineered to produce such molecules at high yield and titres in order to develop new biological methods that satisfy economic constraints. The redox and energetic balances of such strains play crucial roles in performance. Processes performed in strict anaerobes have a limited amount of energy available compared to that in aerobic organisms. This energy is obtained through fermentation and/or ion gradient-driven phosphorylation. Such anaerobic organisms have developed energy conservation mechanisms to increase ATP yields. This paper presents the properties of one of these mechanisms catalysed by the Rnf complex, an ion-translocating membrane complex with a ferredoxin NAD+ oxidoreductase activity. The Rnf complex performs the transfer of electrons from reduced ferredoxin to NAD+ coupled with an ion-motive transport. Ferredoxin is a common electron carrier for anaerobic bacteria and, with NAD+, is involved in several pathways of interest for the production of biofuels. This complex was first identified in Rhodobacter capsulatus and found to be involved in nitrogen fixation. It was then found to be involved in energy conservation in multiple anaerobic organisms, from acetobacteria such as Acetobacterium woodii to sulfate-reducing bacteria such as Desulfovibrio alaskensis and autotrophic bacteria such as Clostridium ljungdahlii and Clostridium aceticum. The Rnf complex triggers two types of ion transports: it can be either a sodium or a proton transporter. Both of these transports create a gradient of ions, generating a membrane potential that is then used by ATPase to produce ATP and thus serving as an energy conservation mechanism. In this review, the available information on the Rnf complex from genetic organization up to its in vivo and in vitro activities in several microorganisms is summarized, with a special focus on the proton-motive Rnf complex.

In order to coordinate the damping performance and energy regenerative performance of energy regenerative suspension, this paper proposes a structure of vehicle semi-active energy regenerative suspension with electro-hydraulic actuator (EHA). In light of the proposed concept, a specific energy regenerative scheme is designed and the mechanical properties test is carried out. Based on the test results, the parameter identification for the system model is conducted using recursive least squares algorithm. On the basis of system principle, the nonlinear model of the semi-active energy regenerative suspension with EHA is built. Meanwhile, LQG control strategy of the system is designed. And then the influence of the main parameters of EHA on the damping performance and energy regenerative performance of suspension is analyzed. Finally, the main parameters of EHA actuator are optimized via genetic algorithm. The test results show that when sinusoidal is input at the frequency of 2Hz and the amplitude of 30mm, the spring mass acceleration RMS value of optimized EHA semi-active energy regenerative suspension is reduced by 22.23% and energy regenerative power RMS value is increased by 40.51%, which means while meeting the requirements of certain vehicle ride comfort and driving safety, energy regenerative performance is improved significantly.

The centrifugal force field in the hydrocyclone was affected by the concave-wall curvature radius R0, the mechanism of droplet deformation was closely related to the mass transfer efficiency. Numerical simulation and experimental data were collected to reveal the deformation characteristics and mechanism of single droplet crossing concave-wall jet. Normalized interfacial energy γ and stretching performance were provided to investigate the droplet deformation process. The results showed that the droplet was stretched along the streamwise and shrank along the spanwise in the concave-wall jet. The droplet interfacial energy and deformation were the largest when the droplet crossed the jet boundary at t = 0.20 s. Maximum γ value increased with the increase of R0 by 57.3% to 71.4%, and the distance between droplet and concave-wall increased with R0. Q-criterion was exported to show the vortex strength increasing as the decrease of R0 in the jet boundary. The pressure distribution inside the droplet showed that the pressure decreased as R0 increased, while the pressure difference increased along the streamwise and wall-normal direction. The study suggested that the droplet breakup was more difficult for the smaller R0, which was beneficial for liquid-liquid heterogeneous separation.

The global energy crisis has lead researchers explore other sources of energy like wind, resulting in a wide acceptance of wind turbines. Vertical axis wind turbines (VAWT) more suitable for small scale application in urban conditions than their horizontal-axis counterparts. A Helical bladed VAWT would reduce the ripple effect when compared to Straight bladed VAWT. The effect of the blade helix angle on the aerodynamic performance of VAWT using 3D numerical simulations is studied. Turbulence modelled using 4-Equation transition SST k-w model. Three different helix angles of 60, 90 and 120 of a 3 bladed VAWT operating across different tip speed ratios were studied. The 60 helical bladed VAWT was found to perform better than all other helical bladed and straight bladed VAWT. Standard deviation of the moment coefficient generated by a blade plotted against 360 of azimuth rotation revealed that the ripple effect on the shaft produced by cyclic loading of the straight blade is considerably reduced upon introduction of helix angle, with 120 helical blade giving lowest standard deviation. The analysis has been done for the percentage of power generated by each quartile of flow and the contribution of each section of the blade. A comparative study was also conducted between different helical bladed VAWT and straight bladed VAWT. Flow feature analysis also revealed the reasons behind secondary peaks and the performance improvement when tip speed ratio increases. Wake structure analysis and flow contours were also studied for a better understanding of the flow field.

Hybrid carbon-silicon, carbon-nitrogen, and carbon-boron clathrates are new classes of Type I carbon-based clathrates that have been identified by first-principles computational methods by substituting atoms on the carbon clathrate framework with Si, N, and/or B atoms. The hybrid framework is further stabilized by embedding appropriate guest atoms within the cavities of the cage structure. Series of hybrid carbon-silicon, carbon-boron, carbon-nitrogen, and carbon-silicon-nitrogen clathrates have been shown to exhibit small positive values of the energy of formation, indicating that they may be metastable compounds and amenable to fabrication. In this overview article, the energy of formation, elastic properties, and electronic properties of selected hybrid carbon-based clathrates are summarized. Theoretical calculations that explore the potential applications of hybrid carbon-based clathrates as energy storage materials, electronic materials, or hard materials are presented. The computational results identify compositions of hybrid carbon-silicon and carbon-nitrogen clathrates that may be considered candidate materials for use as either electrode materials for Li-ion batteries or as hydrogen storage materials. Prior processing routes for fabricating selected hybrid carbon-based clathrates are highlighted and difficulties encountered are discussed.

This paper investigates the energy dissipation level of a nonlinear vehicle suspension system. The suspension system is modelled as a mass-spring-damper system, which is designed using the output frequency response function (OFRF) method. This method enables the derivation of an explicit relationship, between the system output spectrum (or Performance metric) and the system nonlinear parameters of interest. The OFRF polynomial, of the energy dissipation level, was derived in terms of the nonlinear parameters of interest. The results obtained show that the OFRF model, of the energy dissipation level, could be used to estimate the amount of heat dissipated, for a set of design parameters. This has potentials of providing some insights, in the design of vibration-based energy harvesters, as some of the wasted heat energy could be converted to electrical energy.

Symmetry-breaking is a phenomenon that is observed in various contexts, from the early universe to complex organisms, and is considered a key puzzle in understanding the emergence of life. The presence of enantiomeric amino acids and proteins highlights its critical role. However, the origin of symmetry-breaking has yet to be comprehensively explained, particularly from an energetic standpoint. This article explores a novel approach by considering energy dissipation, specifically lost free energy, as a crucial factor in elucidating symmetry-breaking. Through a thorough thermodynamic analysis applicable to enantiomeric systems at various scales, from elementary particles to aggregated matter like crystals, we present experimental findings that establish a direct correlation between non-equilibrium free energy and energy dissipation during formation processes. Results emphasize the pivotal role of energy dissipation not only as an outcome but as the trigger for symmetry-breaking. This insight suggests that understanding the origins of complex systems, from cells to living beings and the universe itself, requires a lens focused on non-equilibrium processes, ultimately facilitating the formation of non-racemic systems.

Perovskite solar cells are an evolving technology owing to self-assembling and highly tunable bandgap properties of materials. In this context, thin films of perovskites have attracted immense attention and witnessed great advancement because of their low manufacturing cost. The key development in these devices is the conversion efficiency, which rose from 3.8% to 28%. The formulation of innovative materials with the proper replacement of lead in perovskites is imperative to mitigate lead toxicity. Here, we analyzed the challenges like material and structural stability, device stability under high temperature and humidity conditions, lifetime, manufacturing cost, etc. faced in the commercialization of perovskite devices. This review shows that challenges such as device engineering, performance stability against the harsh environment, cost-effectiveness, and environmental concern should be taken into consideration for the widespread acceptance of perovskite-based solar devices. In conclusion, we suggested that an enormous scope exists for exploring high-performance and long-lasting perovskites for energy applications.

The purpose of this paper is to describe a new way of producing renewable energy based on fjords as a water heater. We will call this system the Water-thermal Energy Production System (WEPS), because the basic idea is to extract heating and cooling energy from water. Although a prototype of WEPS has existed in Norway for more than ten years, a WEPS currently in operation has not been financially analyzed in the literature. Coastal parts of Norway have a potential of 5 TWh of profitable WEPS-facilities [9], due to convenient access to fjords containing water with stable all-season temperatures of about 4–12C when the depth of the water is about 50 meters. This stability of the water temperature makes it possible to extract energy from the fjord in a very efficient way. The potential for economically-profitable WEPS in other parts of the world has not been estimated. In order to answer such a question, more research is required. We have conducted a case study of a WEPS located in the Norwegian municipality of Eid. This is the first full-scale Norwegian WEPS, and it has been operating since 2006. The nascent years have passed, and the technology has been in operation for some years. In this paper, we have made an estimate of the business profitability and the external effects based on past empirical evidence and some assumptions about future development in some key figures. The results suggests that WEPS-Eid has been a profitable investment carrying a positive internal rate of revenue, even if the present underutilization in production capacity will continue in the future. Stability in energy prices for heating purposes has also gained customers compared to the more volatile prices of alternative renewable energy, like hydropower or wind turbines. The negative, external effects in the operating phase from WEPS-Eid are insignificant. Despite the significant profitability of the WEPS facility in Eid, there are two main obstacles for new entrants. There is a lack of relevant operational information for potential investors due to few facilities. This leads to uncertainty, and investments in WEPS appear as a risky business. Secondly, construction of a WEPS requires both big financial investments in digging and facilitating long trenches for a pipeline system and time and effort spent on acquiring the licenses needed for doing this work. A coordinating unit is probably required in order to get the necessary public and private licenses and to reduce fixed costs by coordinating other tasks in the same trenches, like pipes for water and sewer, fiber cables and tele-cables. In Eid, the local municipal administration was the coordinating unit.

The objective of this paper is to present a mathematical formalism that states a bridge between Physics and Psychology, concretely between analytical dynamics and personality theory in order to open new insights in this theory. In this formalism energy plays a central role. First, the short-term personality dynamics can be measured by the General Factor of Personality (GFP) response to an arbitrary stimulus. This GFP dynamical response is modelled by a stimulus-response model: an integro-differential equation. The bridge between Physics and Psychology is provided when the stimulus-response model can be formulated as a linear second order differential equation and, subsequently, reformulated as a Newtonian equation. This bridge is strengthened when the Newtonian equation is derived from a minimum action principle, obtaining the current Lagrangian and Hamiltonian functions. However, the Hamiltonian is a non-conserved energy. Then, some changes provide a conserved Hamiltonian function: the Ermakov-Lewis energy. This energy is presented, as well as the GFP dynamical response that can be derived from it. An application case is presented: an experimental design in which 28 individuals consumed 26.51 g of alcohol. This experiment provides an ordinal scale for the Ermakov-Lewis energies that predicts the effect of a single dose of alcohol.

It's a method to achieve energy savings in single-phase active power greater than that obtained with the "Fan Law" in electric machines applied to ventilation. Quantitative analysis methods were based on electrotechnical techniques, practiced with the corresponding laboratory equipment on the working materials (three prototypes of electric machines). The results obtained from experimentation on the test bench were recorded in tables that collect data of formulas, values, and physical units. The discussion provides a comprehensive comparative study, mainly between power (watts), active energy consumption (kWh), and rotational speed (revolutions per minute). The permanent magnet synchronous motor (PMSM) with the coupling of an RL circuit design does mechanical work at its maximum speed of 3000 (RPM) with only 6.3 (Watts), which is equivalent to 25.2% of the active power required by the single-phase induction asynchronous motor (or shaded pole motor), which required 25 (Watts) to rotate at 1690 (RPM). This translates to 75% lower active power with a 44% superiority in speed, resulting in a 75% savings in single-phase active energy (measured in kWh). The same occurs when comparing it to the universal AC motor (with brushes and wound rotor) to maintain a speed of 3000 (RPM); since it consumes 64.8 (Watts), which is 90.3% more single-phase active energy than that required to achieve the same rotational speed as the permanent magnet synchronous motor (PMSM). The study was conducted on all motors with the same impeller blade diameter and under identical air temperature and atmospheric pressure conditions.

Fractured media are seldom considered viable for storing excess thermal energy seasonally, compared to the more commonly used porous aquifers, due to their heterogeneity, lower storage capacity, and potential for unpredictable flow paths. This study employs COMSOL Multiphysics to create a numerical model of a fractured granite reservoir located below the Bedretto underground laboratory. The energy efficiency of both single-well and doublet systems was evaluated over 25 cycles, each comprising four 91-day phases: injection, storage, production, and resting. Results indicated that the single-well system was more efficient, with energy efficiency increasing with the flow rate. For an injection temperature of 60 °C, the system achieved energy efficiencies of up to 59.3% and 67.7%, after 10 and 25 cycles, respectively, aligning with porous Aquifer Thermal Energy Storage (ATES) system efficiencies at this temperature. Exploration of electricity production using water injected at 120 °C revealed it to be uneconomical and ineffective. However, the most promising use of the retrieved water was found to be direct ground heating for a greenhouse. This technology offers a potential alternative for thermal energy storage in regions lacking suitable porous aquifers, although identifying appropriate locations with the necessary geological characteristics may present significant challenges.

We considered the hypothesis that the sources of dark energy (DE) could be black holes (BHs) or more exotic objects, such as naked singularities or gravastars. We proposed a definition of the presence of DE in the Universe and a criterion for what can be considered the source of this dark energy. It is based on the idea of the accelerated expansion of the Universe, which requires antigravity caused by large negative pressure. A recently proposed hypothesis was examined that mass of BHs increases with time according to the same law as the volume of the part of the Universe containing it and the population of BHs can mimic DE. We demonstrate the reasons why it cannot be accepted, even if all the assumptions on which this hypothesis is based are considered true.

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

For thermoelectric materials study and development, it is very important to measure the electrical power and efficiency of a thermoelectric generator (TEG). In this study, thermoelectric properties such as electrical conductivity, Seebeck coefficient, and thermal conductivity of cement composites with graphene nanoplatelets and metallic oxides (Fe2O3, ZnO, MnO2) are measured and subsequently used to figure out the output electrical power and efficiency. A maximum of 1.5 W power per square meter for a temperature difference of about 50 °C can be estimated using GnP-ZnO added cement composites. This paper also talks about how to make a cement composite-based structural TEG module to enhance the total output voltage, power, and efficiency of the system.

Peer-to-peer (P2P) energy trading is a new data-driven business model currently being trialed within the energy sector. Introducing P2P transactions to an essential service such as energy could have far-reaching implications for individuals and the grid. This paper raises considerations and questions from social, economic/markets and regulatory points of view, that should be understood and addressed by societies and policymakers. It does this by considering under what circumstances it is reasonable to conceptualize P2P energy trading as part of the sharing economy, and drawing parallels to the sharing economy experience in other sectors. In order to reap the full societal benefits, while avoiding considerable risks to infrastructure and individuals, a policy approach promoting dialogue and innovation is necessary. We suggest the regulatory sandbox is the most appropriate tool to achieve this and would help avoid the breakdown of trust between policymakers and platform companies observed in other sectors.

The present paper aims to elucidate the impact of climate change on the availability and security of water and energy in the Middle East and North Africa Region (MENA Region). The region is particularly challenged by a number of factors including a large variability of bio-geographical characteristics, extreme population growth over the last few decades and substantial societal and economical transitions as well as armed conflicts in some of the countries of the region. Anticipated changes in climate conditions will exacerbate the challenges with regard to providing sufficient amounts of water and energy to the communities in the region. Impacts of climate change will materialize as an increasing number of heat waves, primarily in urban structures and the decline in water availability as a result of enhanced droughts and a growing numbers of dry spells. The interrelationships between energy and water and their mutual dependencies are addressed by the Water-Energy-Nexus concept. With regard to the challenges addressed here, Cyprus and the Eastern Mediterranean are a particular point in case. Mitigation and adaptation strategies include enhanced efficiency of energy and water use, integrated technology assessments regarding electricity generation and the production of potable water and electricity through concentrated solar power.

Industrial buildings have numerous energy-losing equipment, such as engines, ovens, boilers, and heat exchangers. Energy losses are related to inefficient energy use and lousy work conditions for the people inside the buildings. This work is devoted to the recovery of lost energy from industrial buildings. Firstly, the residual energy of the building is extracted to be used to warm water. Consequently, the work conditions of the people inside industrial buildings can be improved by maintaining the adequate temperature. The recovery energy is done by the multipurpose heat pump system (HP system). The working fluid used in the HP system is R134a, which is a traditional and cheap working fluid. The thermophysical properties of R134a are obtained through the PC-SAFT equation of state. This work presents a performance mapping based on the intercepted areas framework to evaluate which working conditions are the optimal operating variables. The latter depends on several key parameters, such as compressor work, heat delivery, heat absorbed, and exergetic efficiency. The results show that the optimal work conditions are found at different condenser and evaporator temperatures, and that may be limited by what the designer considers a good performance of the heat pump system.

For a decade, the studies of dynamic control for unmanned aerial vehicles took a large interest, where drones as a useful technology in different areas were always suffering from several issues like instability-high energy consumption of batteries - inaccuracy of tracking targets. Different approaches are proposed for dealing with the non-linearity issues which present the most important features of this system. This paper describes our focus on the most common control strategies, known as model predictive control MPC, by developing a model based on the sensors embedded in our Tello quadrotor used for indoor purposes. The original controller of Tello quadrotor is supposed to be a slave, where the designed model predictive controller is created in MATLAB and imported to another embedded system, considered as a master; the objective of this model is to track the reference trajectory, almost keeping the stability of the system and ensure the low energy consumption. In the first part, a profound description of the modelling process of a dynamic model for drones is presented, explaining the design of MPC controller with both linear and non-linear strategies built in MATLAB. In the final part, simulation and results are discussed regarding its behaviour and performance, highlighting the MPC model's important role on drones' energy consumption profile.

The objective of this article: analysis of research trends on the topic "Materials Science for Energy Engineering" for the period 2012-2021. Materials and methods: bibliometric analysis of data from the Scopus abstract database.Results. It is shown that this topic is developing faster than the general energy topics.The key feature of the research trends is a significant increase in work on the development of materials for renewable energy and a decrease in the number of publications related to nuclear power.The primary goal of many studies is to increase the efficiency of renewable energy production through the use of new materials.The importance of the topic is evidenced by the emergence of new journals that quickly entered the first quartile of the abstract databases Scopus and Web of Science, for example: ACS Applied Energy Materials.There has been a significant increase of interest in perovskite solar cells, layered semiconductors, triboelectric nanogenerators, cobalt compounds, sulfur compounds, and oxygen and hydrogen evolution reaction during Electrolysis.Publications on electric batteries are well represented in all time intervals. The focus is on electrode materials and battery efficiency.

In this study we investigate the formation of dynamical energy cascades in higher order KdV-type equations. In the beginning we recall what is known about the dynamic cascades for the classical KdV (quadratic) and mKdV (cubic) equations. Then, we investigate further the mKdV case by considering a richer set of initial perturbations in order to check the validity and persistence of various facts previously established for the narrow-banded perturbations. Afterwards we focus on higher order nonlinearities (quartic and quintic) which are found to be quite different in many respects from the mKdV equation. Throughout this study we consider both the direct and double energy cascades. It was found that the dynamic cascade is always formed, but its formation is not necessarily accompanied by the nonlinear stage of the modulational instability. Direct cascade structure remains invariant regardless the size of the spectral domain. In contrast, the double cascade shape can depend on the size of the spectral domain, even if the total number of cascading modes remains invariant. Results obtained in this study can be potentially applied to plasmas, free surface and internal wave hydrodynamics.

In this study, we investigate the formation of dynamical energy cascades in higher-order KdV-type equations. In the beginning, we recall what is known about the dynamic cascades for the classical KdV (quadratic) and mKdV (cubic) equations. Then, we investigate further the mKdV case by considering a richer set of initial perturbations in order to check the validity and persistence of various facts previously established for the narrow-banded perturbations. Afterwards, we focus on higher-order nonlinearities (quartic and quintic) which are found to be quite different in many respects from the mKdV equation. Throughout this study, we consider both the direct and double energy cascades. It was found that the dynamic cascade is always formed, but its formation is not necessarily accompanied by the nonlinear stage of the modulational instability. Direct cascade structure remains invariant regardless of the size of the spectral domain. In contrast, the double cascade shape can depend on the size of the spectral domain, even if the total number of cascading modes remains invariant. Results obtained in this study can be potentially applied to plasmas, free surface and internal wave hydrodynamics.

Energy and Environment Tax is used globally as a means of environment policy. Energy and Environment tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy and environmental taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy and environmental taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and to suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy and environmental taxes. Results of this study show that South Korea’s energy and environmental taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy and environmental tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy and environmental taxation. However, energy and environmental taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy and environmental taxation

With the dramatic increase in world population, continued advances in modern greenhouse agriculture and plant growth practices are expected to help overcome the global problem of future food shortages. Next generation greenhouse design practices will need to address a range of issues, ranging from energy and land use efficiency to providing plant-optimised growth techniques. In this paper, we focus on investigating the optimum irradiation spectra matched to the lettuce species (Lactuca sativa, L.), which is commonly grown in greenhouse environments, in order to develop low-emissivity glass panes that maximize the biomass productivity of glass greenhouses. This low-emissivity glass passes the solar spectral components needed for crop growth, while rejecting other unwanted radiations, leading to significant energy savings and other beneficial effects related to greenhouse climate control, in a range of climates. This is due to reducing both the solar heat gain and photosaturation, which can raise the temperature of the crops to harmful levels. Experimental results show that substantial biomass productivity improvements in lettuce (up to ~14.7%) can be attained using spectrally optimized illumination, compared with white light irradiation. We also report on the development of advanced metal-dielectric thin-film filters that produce the optimum illumination spectrum when exposed to sunlight.

In this study, the impact of energy, agriculture, macroeconomic and human-induced indicators on environmental pollution from 1971 to 2011 is investigated using the statistically inspired modification of partial least squares (SIMPLS) regression model. There was evidence of a linear relationship between energy, agriculture, macroeconomic and human-induced indicators and carbon dioxide emissions. Evidence from the SIMPLS regression shows that a 1% increase in crop production index will reduce carbon dioxide emissions by 0.71%. Economic growth increased by 1% will reduce carbon dioxide emissions by 0.46%, thus supports the environmental Kuznets curve hypothesis that an increase in a country’s economic growth leads to a reduction in environmental pollution. An increase in electricity production from hydroelectric sources by 1% will reduce carbon dioxide emissions by 0.30%, thus increasing renewable energy sources in Ghana’s energy portfolio will help mitigate carbon dioxide emissions. Increasing Enteric Emissions by 1% will increase carbon dioxide emissions by 4.22% and a 1% increase in the Nitrogen content of Manure Management will increase carbon dioxide emissions by 6.69%. The SIMPLS regression forecasting exhibited a 5% MAPE from the prediction of carbon dioxide emissions.

Development of methods and algorithms to predict the effect of mutations on protein stability, protein-protein, and protein-DNA/RNA binding is necessitated by the needs of protein engineering and for understanding the molecular mechanism of disease-causing variants. The vast majority of the leading methods are either methods with adjustable parameters or machine learning algorithms, both requiring a database of experimentally measured folding and binding free energy changes. These databases are collections of experimental data taken from scientific investigations typically aimed at probing the role of particular residue on the above-mentioned thermodynamics characteristics, i.e., the mutations are not introduced at random and do not necessarily represent mutations originating from single nucleotide variant (SNV). Thus, the reported performance of the leading algorithms assessed on these databases or other limited cases, may not be applicable for predicting the effect of SNVs seen in the human population. Indeed, we demonstrate that the SNVs and non-SNVs are not equally presented in the corresponding databases and the distribution of the free energy changes are not the same. Furthermore, the Pearson correlation coefficients (PCCs) obtained on cases involving SNVs are less impressive than for non-SNVs, indicating that caution should be used in applying them to reveal the effect of human SNVs. All methods are found to underestimate the energy changes by roughly a factor of 2.

Offshore electricity production, mainly by wind turbines, and eventually floating PV in the future, will contribute to increase renewable energy production, as well as their dispatchability. The need for that energy evacuation and the implementation of the hydrogen economy are challenges that arise the evaluation of such energy facilities for the direct production of hydrogen. The analysis of the alternatives for the evacuation of offshore renewable electricity for the production of hydrogen is presented. The analysis includes discussion about the current state of the art of hydrogen pipelines and subsea cables, as well as the storage and bunkering system that is needed on shore. The main options for energy evacuation will be via an electric subsea cable to produce hydrogen onshore, or by pipeline, depending on the capacity of the offshore plant. For low capacity, an electric subsea cable is the best option. For high capacity renewable offshore plants, pipelines start to be competitive for distances above aprox. 450 miles.

Following the international trend of using hydrogen as combustible in many industry branches, this paper investigates the impact of mixing methane gas with 23% hydrogen (G222) on condensing boilers’ operation. After modeling and testing several boilers with heat exchange surface different designs, the authors gathered enough information to introduce a new concept, namely High-Performance Condensing Boiler (HPCB). All the boilers that fit into this approach have the same operational parameters at nominal heat load, including the CO2 concentrations in flue gases. After testing a flattened pipes condensing boiler, a CO2 emission reduction coefficient of 1.1 was determined, when converting from methane gas to G222 as combustible. Thus, by inserting into the national grid a G222 mixture, an important reduction in greenhouse gases can be achieved. For a 28 kW condensing boiler the annual reduction in CO2 emissions averages 1.26 tons, value which was experimentally obtained and is consistent with the theoretical evaluation.

This review paper addresses the growing challenges and developments in frequency control within power systems influenced by increasing penetration of renewable energy sources. It evaluates the advancements and limitations of renewable-based control technologies and explores the critical role of diverse energy storage technologies in providing fast frequency response ancillary services. Through a comprehensive analysis of global literature, this paper categorizes energy storage solutions according to their efficacy in meeting fast frequency response demands and potential for revenue generation. It reveals significant gaps in current research, which predominantly focuses on battery energy storage systems and microgrid applications, with insufficient attention to grid-scale storage solutions and innovative energy storage technologies. This analysis identifies a lack of detailed technical simulations and hybrid storage models for frequency control, as well as a minimal exploration of the environmental benefits, particularly in terms of carbon dioxide emission reductions, associated with deploying new energy storage technologies in ancillary service markets. The paper concludes by highlighting the necessity for further research incorporating detailed techno-economic evaluations and carbon dioxide reduction potential of modular, scalable energy storage technologies, facilitated by advanced network simulation models and comprehensive market analysis.

With the increasing prominence of renewable energy sources providing flexibility to the power grid, there is a growing recognition of the need to expand virtual Energy Storage Systems (ESS) to replace traditional ESS, which faces challenges in terms of supply and scalability. Grid-connected microgrids can supply power stably and are being built, so they can be used as virtual ESS to provide flexibility to the power system. This study proposes an approach to determine the optimal Power Conversion System (PCS) and battery capacity for a Virtual Energy Storage System(VEES) based on a grid-connected microgrid incorporating Photovoltaic (PV) and ESS. In this paper, it is assumed that microgrids can provide flexibility to the grid by participating in the energy trading market, there are corresponding profits and penalties for order. Numerical examples are performed to demonstrate the effectiveness of the proposed method.

Motivated by South Africa's need in the transition to a net-zero economy; this study 10 investigates the integration of renewable energy sources (RES) into oil refineries, considering 11 therein unique challenges and opportunities. The research focuses on optimizing RES allocation 12 using Particle Swarm Optimization (PSO), a data-driven approach that adapts to real-time 13 operational conditions. Traditional energy management systems often struggle with the inherent 14variability of RES, leading to suboptimal energy distribution and increased emissions. Therefore, 15 this study proposes a PSO-based renewable energy allocation strategy specifically designed for oil 16 refineries. It considers factors like the levelized cost of energy, geographical location, and available 17 technology. The methodology involves formulating the optimization problem, developing a PSO 18 model, and implementing it in a simulated oil refinery environment. The results demonstrate 19 significant convergence of the PSO algorithm, leading to an optimal configuration for integrating 20 RES and achieving cost reductions and sustainability goals. The optimization result of 4,457,527.00 21 Rand achieved by iterations is much better than the result of 4,829,638.88 Rand acquired using 22Linear Programming as the baseline model. The mean cost, indicating consistent performance, has 23 remained at its original value of 4,457,527.00 Rand, highlighting the convergence. Key findings 24 include the average distance measure decreasing from 4.2 to 3.4, indicating particle convergence; 25 swarm diameter decreasing from 4.7 to 3.8, showing swarm concentration on promising solutions; 26 average velocity decreasing from 7.8 to 4.25, demonstrating refined particle movement; and the 27 optimum cost function achieved at 4,457,527 Rand with zero standard deviation, highlighting 28 stability and optimal solution identification. This research offers a valuable solution for oil 29 refineries seeking to integrate RES effectively, contributing to South Africa's transition to a 30sustainable energy future.

Cities consume over 75% of natural resources, produce over 50% of global waste and emit 60 - 80% of greenhouse gases. The scenario that by 2050 two thirds of the world population will live in cities, highlights how cities are still responsible of the growing consumption characterized by linear economy processes, with the production of various types of waste. In this unsustainable framework, the Circular Economy offers the opportunity to shape the urban system by means of rethinking the possibility to produce and use goods and services exploring new ways to ensure long-term prosperity. The Circular City paradigm contains in fact all the principles of the Circular Economy: recovery, recycling and sharing. In particular, Circular City also introduces actions related to the development of renewable energy communities, use of green materials, CO2 absorption approaches and Proximity Cities. The aim of this work is to develop a methodology to build a composite index (Circular City Index) capable of measuring the degree of implementation of urban policies that enable the territory to initiate an ecological transition of public assets. The city of Cagliari (Sardinia, Italy) represents the case study to apply circular urban policies in public properties, for civil and military use.

Capacitance measurements have been extensively used to measure the anchoring extrapolation length L at a nematic-substrate interface. These measurements are extremely delicate because the value found for L often critically depends on the sample thickness and the voltage range chosen to perform the measurements. Several reasons have been proposed to explain this observation, such as the presence of inhomogeneities in the director distribution on the bounding plates or the variation with the electric field of the dielectric constants. In this paper I propose a new method to measure Lp that takes into account this second effect. This method is more general than that proposed in Murauski et al. Phys. Rev. E 71, 061707 (2005) because it does not assume that the anchoring angle is small and that the anchoring energy is of the Rapini-Papoular form. This method is applied to a cell of 8CB treated for planar unidirectional anchoring by photoalignment with the azobenzene dye Brilliant Yellow. The role of flexoelectric effects and the shape of the anchoring potential are discussed.

The wide interest in developing green energy technologies stimulates the scientific community to seek, for devices, new substitute material platforms with low environmental impact, ease of production and processing and long-term stability. The synthesis of metal oxide (MO) semiconductors fulfils these requirements and efforts are addressed at optimizing their functional properties, through improvement of charge mobility or energy level alignment. Two MOs have rising perspectives for application in light harvesting devices, mainly for the role of charge selective layers but also as light absorbers, namely MoO3 (an electron blocking layer) and Co3O4 (a small band gap semiconductor). The need to achieve better charge transport has prompted us to attempt doping strategies with vanadium (V) ions that, when combined with oxygen in V2O5, produce a high work function MO. We report on subcritical hydrothermal synthesis of V-doped mesostructures of MoO3 and of Co3O4, in which a tight control of the doping is exerted by tuning the relative amounts of reactants. We accomplished a full analytical characterization of these V-doped MOs that unambiguously demonstrates incorporation of the vanadium ions in the MO crystal lattice, as well as effects on the optical properties and work function. We foresee a promising future use of these materials as charge selective materials in energy devices based on multilayer structures.

Considering the manufacturing of automotive components, there exists a dilemma around the substitution of traditional Cast Iron (CI) with lighter metals. Nowadays, aluminium alloys, being lighter compared to traditional materials, are considered as a more environmentally friendly solution. However, the energy required for the extraction of the primary materials and manufacturing of components is usually not taken into account in this debate. In this study, an extensive literature review has been performed to estimate the overall energy required for the manufacturing of an engine cylinder block using (a) cast iron and (b) aluminium alloys. Moreover, data from over 100 automotive companies, ranging from mining companies to consultancy firms, have been collected in order to support the soundness of this investigation. The environmental impact of the manufacturing of engine blocks made of these materials is presented with respect to the energy burden; the “cradle-to-grave approach” has been implemented to take into account the energy input of each stage of the component lifecycle starting from the resource extraction and reaching to the end-of-life processing stage. Our results indicate that although aluminium components contribute towards reduced fuel consumption during their use phase, the vehicle distance needed to be covered in order to compensate for the up-front energy consumption related to the primary material production and manufacturing phases is very high. Thus, the substitution of traditional materials with lightweight ones in the automotive industry should be very thoughtfully evaluated.

The surprisingly high catalytic activity of gold has been known to the heterogeneous catalysis community since the mid-1980s. Significant effort has been directed towards improving the reactivity of these surfaces towards important industrial reactions. One such strategy is the introduction of small amounts of other metals to create Au-based surface alloys. In this work, we investigate the synergistic effect of Pt doping of the Au(111) surface towards decreasing the activation barrier of the methanol dehydrogenation elementary step, within first-principles density functional theory. To this aim we construct several models of \ce{Pt}-doped Au(111) surfaces, including a full \ce{Pt} overlayer and monolayer. The effect of \ce{Pt} surface doping is then investigated via the computation of adsorption energies of the various chemical species involved in the catalytic step, and the estimation of activation barriers of methanol dehydrogenation. Both electronic and strain effects induced by \ce{Pt} surface doping concur in substantially lowering the activation energy barrier of this important reaction elementary step. Morever, in the presence of preadsorbed atomic oxygen, \ce{Pt} surface doping can be used to reduce the activation energy for methanol dehydrogenation to as low as 0.1 eV.

IoT system becomes hot topic nowadays for smart home, IoT helps devices to communicate together without human intervention inside home, so it is offering many challenges. A new smart home IoT platform powered using electromagnetic energy harvesting is proposed in this paper. It contains a high gain transmitted antenna array and efficient circular polarized array rectenna system to harvest enough power from any direction to increase life time of the batteries used in IoT system. Optimized energy consumption, the software with adopting the Zigbee protocol of the sensor node and low power microcontroller are used to operate in lower power modes. The proposed system has an 84.6 days lifetime which is approximately 10 times the lifetime for similar system. On the other hand, the proposed power management circuit operated at 0.3 V DC to boost the voltage to ~3.7V from radio frequency energy harvesting and manage battery level to increase the batteries lifetime. A predictive indoor environment monitoring system is designed based on a novel hybrid system to provide a non-static plan, approve energy consumption and avoiding failure of sensor nodes in smart home.

Building energy consumption plays an essential role in urban sustainability. The prediction of the energy demand is also of particular importance for developing smart cities and urban planning. Machine learning has recently contributed to the advancement of methods and technologies to predict demand and consumption for building energy systems. This paper presents a state of the art of machine learning models and evaluates the performance of these models. Through a systematic review and a comprehensive taxonomy, the advances of machine learning are carefully investigated and promising models are introduced.

The cost effective design of tidal turbines requires a good estimation of the loading cycles and their extrema that are related to the unsteady fluctuations of the current velocity. Apart from the ambient turbulence, the main source of velocity fluctuations is the presence of surface waves. In the present study, we analyse the effect of waves propagating against the current on the performance and the loads of a twin vertical axis tidal turbine by an experimental approach at a 1/20 scale. Overall, the results show little or no effect of the waves on the average power and loads compared to the condition with current only, but a significant impact on their standard deviation that rises linearly with the waves amplitude. The drag, lift and pitching moment show extended ranges up to 7.5 times higher and extreme values exceedance by 60 to 100 % with irregular waves compared to the condition without waves. Those load and power fluctuation increase are fully due to the presence of waves as the coherence function between the rotor torque or the loads and the velocity spectra exceed 0.5 on the whole wave frequency bandwidth. The results also reveal a rotational sampling of the waves by the rotors that had also been observed on horizontal axis turbines. From a structural design point of view, the authors recommand to conduct tests in irregular wave conditions as the loads range and extreme values are 1.5 to 2 times higher than those encountered with regular waves of the same significant height and period.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

The thermal degradation of brakes has a significant impact on the stability of pure electric commercial vehicles during long downhill braking. Based on road slope and using fuzzy control method, design strategies for motor regenerative braking force and friction braking force distribution, with the aim of reducing friction braking force, improving braking stability, and recovering braking energy. By establishing driving conditions on roads with different slopes and using numerical analysis methods to verify the proposed control strategy. the results show that under the 6% constant slope driving condition, the vehicle maintains a constant speed of 30km/h downhill driving, and the braking energy recovery rate reaches 50.93%; Under the condition of 3% -6% gradient driving, the vehicle speed fluctuates slightly, but it can still be maintained at a constant speed of 30km/h for downhill driving through the adjustment of the motor's reverse drag characteristic, with a braking energy recovery rate of 49.97%; During the process of driving downhill at a constant speed, the frictional braking force does not participate in braking; The braking energy recovery rate is determined by the slope and braking deceleration.

This study aimed to evaluate a cantilever beam-type piezoelectric energy harvester operating on train-induced vibrations for powering Wireless Sensor Networks (WSNs) used in railway track monitoring systems. The harvester's behaviors under different conditions are simulated in MATLAB using the analytical model. Natural frequency, maximum deflection, and stress were calculated with greater precision using eigenfrequency and stationary analysis using COMSOL Multiphysics. At a base excitation of 2 g and a resonant frequency of 4.38 Hz, the simulated results showed that the developed energy harvester prototype could generate up to 14 V of AC output voltage and 550 mW of output power. These findings highlight the promising potential of the proposed energy harvester for transforming train mechanical energy into electrical power. This energy harvester's viability and dependability for real-world applications in monitoring railway tracks are supported by developed analytical and simulation models.

Silk fibroin is a well-known biopolymer used in several applications in which the interaction with biological tissue is required. In fact, fibroin is extremely versatile and can be shaped to form several constructs useful in tissue engineering applications. Confocal imaging is usually per-formed to test the cells behaviour on the construct and in this context the fibroin autofluorescence is regarded as a problem. In addition, the autofluorescence is not intense enough to provide useful morphological images. In fact, to control study the constructs morphology other techniques are used (i.e. SEM, Micro-CT). In this work we propose a method based on the fluorescence energy transfer (FRET) to suppress the fibroin autofluorescence moving it to higher wavelength accessible to the confocal microscopy for a direct imaging.

In the paper, a fully discrete compact difference scheme with $O(\tau^{2}+h^{4})$ precision is established by considering the numerical approximation of the one-dimensional Allen-Cahn equation. The numerical solutions satisfy discrete maximum principle under reasonable step ratio and time step constraint is proved. And the energy stability for the fully discrete scheme is investigated. An example is finally presented to show the effectiveness of scheme.

The use of Smart Antenna Systems (SAS) in pervasive environments such the Mobile Ad hoc Networks (MANET) has been promoted as the best choice to improve Spatial Division Multiple Access (SDMA) and throughput. Although directional communications are expected to provide great advantages in terms of network performance, directional MAC (Medium Access Control) protocols introduce several issues. One of the most known problems in this context is represented by the fact that, attempting to solve or at least mitigate the problems introduced by these kinds of antennas especially at MAC layer, a large amount of energy consumption is achieved ; for example, due to excessive retransmissions introduced by very frequently issue such as deafness and handoff. The expedients proposed in order to reduce these drawbacks attempting to limit beamforming time of nodes in cooperation with a Round-Robin scheduling, can grant high performance in terms of fairness and throughput. However the overall energy consumption in the network is not efficent due to the static approach. In view of this, we propose an Adaptive Beamforming Time with Round-Robin MAC providing for a dynamic assignment of the beamforming time with the purpose to limit the waste of energy of nodes.

In this paper, we investigate various graphene monolayer nanomesh structures (diodes) formed only by nanoholes, with a diameter of just 20 nm and etched from the graphene layer in different shapes (such as rhombus, bow-tie, rectangle, trapezoid, and triangle), and their electrical properties targeting electromagnetic energy harvesting applications. In this respect, the main parameters characterizing any nonlinear device for energy harvesting are extracted from tens of measurements performed on a single chip containing the fabricated diodes. The best nano-perforated graphene structure is the triangle nanomesh one, which exhibits remarkable performance in terms of its characteristic parameters, i.e., a 420 Ω differential resistance for optimal impedance matching to an antenna, a high responsivity greater than 1000 V/W, and a low noise equivalent power of 847 pW/√Hz at 0 V.

The Sunyaev-Zeldovich effect (SZe) is a global distortion of Cosmic Microwave Bckground (CMB) spectrum as result of its interaction with a hot electron plasma in the intracluster medium for large gravitational virialized structures such as galaxy clusters. Furthermore, this hot gas of electrons emits X-Rays due to its fall in the gravitational potential well of the cluster. The analysis of SZe and X-Ray data, provide a method for calculating distances to galaxy clusters at any redshift (Angular diameter distance (d_A) and gas mass fraction (f_gas)). On the other side, many of these galaxy clusters produce a Strong Gravitational Lens effect (SGL), which has become an useful astrophysical tool for cosmology. We use these cosmological tests, in addition to the more traditional ones (SNIa, CMB, BAO), to constraint alternative models of dark energy (ωCDM, CPL, IDE, EDE) and study the history of expansion through the cosmographic parameters (H(z), q(z), j(z)). Using Akaike and Bayesian Information Criterion (AIC, BIC) we find that the ωCDM and ΛCDM models are the most favored by the observational data. In addition, we found that at low redshift appears an peculiar behavior of slowdown of aceleration, which occurs only on dynamical dark energy models using only galaxy clusters (d_A,clusters + f_gas).

In this paper, we consider the behavior of the local energy flow velocity of the fundamental air – core mode at the core – cladding boundary in two types of hollow – core fibers: hollow – core fibers with a negative curvature of the core boundary and single – capillary fibers with similar geometrical parameters. It is demonstrated that the behavior of both axial and radial components of the local energy velocity of the fundamental air – core mode is completely different for these two types of hollow – core fibers. The negative curvature of the core boundary leads to an alternating behavior of the radial projection of the local energy velocity and a decrease by two orders of magnitude compared to the values of this projection for a single capillary. In our opinion, this behavior of the local energy velocity of the fundamental air – core mode is caused by a periodic set of Poynting vector vortices that appear in the cladding capillary walls.

Energy storage systems will play a key role for individual users in the future smart grid. They serve two purposes: (i) handling the intermittent nature of renewable energy resources for a more reliable and efficient system, and (ii) preventing the impact of blackouts on users and allowing for more independence from the grid, while saving money through load-shifting. In this paper we investigate the latter scenario by looking at a neighbourhood of 25 households whose demand is satisfied by one utility company. Assuming the users possess lithium-ion batteries, we answer the question of how each household can make the best use of their individual storage system given a real-time pricing policy. To this end, each user is modelled as a player of a non-cooperative scheduling game. The novelty of the game lies in the advanced battery model, which incorporates charging and discharging characteristics of lithium-ion batteries. The action set for each player comprises day-ahead schedules of their respective battery usage. We analyse different user behavior and are able to obtain a realistic and applicable understanding of the potential of these systems. As a result, we show the correlation between the efficiency of the battery and the outcome of the game.

This compendium presents new mathematical techniques for modeling Point Absorbers. A combined frequency-time domain framework is developed. It is used to simulate the energy generated by the wave farms. With Matlab and Fortran as a base, this leads to obtain physical variables of primary importance, namely position, velocity and power to energy net balance relationships of absorption. Integration of different degrees of freedom with heave as main executable leads in turn to a single buoy motion focus. Acquisition of the needed hydrodynamic coefficients is provided through application of potential field solvers with Boundary Element Methodology background. Initially, this Wave-to-motion model is validated by comparison with previous experimental results for a floating cone cylinder shape (Buldra-FO3). A single, generic, vertical floating cylinder is contemplated then, that responds to the action of the passing regular waves excitation. Later, two equally sized vertical floating cylinders aligned with the incident wave direction are modeled for a variable distance between the bodies. For both unidirectional regular and irregular waves as an input in deep water, we approximate the convolutive radiation force function term through the Prony method. By changing the spatial disposition of the axisymmetric buoys, using for instance triangular or rectangular shaped arrays of three and four bodies respectively, the study delves into motion characteristics for regular waves. The results highlight efficient layouts for maximizing the energy production whilst providing important insights into their performance, revealing displacement amplification- and capture width-ratios, while deriving in possible interpretations of scenarios related to the known park effect. These terms are encompassed by the novelty of a new conceptual Post-Processing methodology in the field, which leads to obtain an optimal distance for the separated bodies with effective energy absorption in a regular wave regime. The main objective is to generate a tendency within the hydrodynamic field of study, which is the Wave to motion perspective. More generally, this computational excursion envisions and depicts potential fields of study, which will surely enhance new connections and link this renewable energy form. Therefore, this research delves first into the historical and technical background on Ocean Wave Energy. Next, it is in the section regarding Materials and Methods, where boundaries and related equations are introduced step by step, together with latter mentioned case scenarios, and their corresponding configuration parameters. A separate section frames then the scope of results, while finally, there is an ensuing discussion and conclusions for evaluation assessment.

Based on stochastic frontier analysis and translog input distance function, this paper examines the total factor energy efficiency of China’s industry using input-output data of 30 sub-industries from 2002 to 2014, and decomposes the changes in estimated total factor energy efficiency into the effects of technical change, technical efficiency change, scale efficiency change and input-mix effect. The results show that during this period the total factor energy efficiency in China’s industry grows annually at a rate of 3.63%, technical change, technical efficiency change and input-mix effect contribute positively to the change in total factor energy efficiency, while scale efficiency change contributes negatively to it.

Space-time evolution of our universe is explained by using the 3-dimensional quantized space model (TQSM) based on the 4-dimensional (4-D) Euclidean space. The energy (E = cDtDV), charges and energy density (|q| = r = cDt) and absolute time (ct) are newly defined based on the 4-D Euclidean space. The photon flat space with the constant energy density of r = cDt_q is proposed as the dark energy (DE). The dark energy is separated into the n DE and photon DE which create the new photon spaces with the constant energy density of r = cDt_q. The v DE is from the n pair production by the CPT symmetry and the photon DE is from the photon space pair production by the T symmetry. The vacuum energy crisis and Hubble’s constant puzzle are explained by the photon space with the n DE and photon DE. The big bang and inflation of the primary black hole is connected to the accelerated space expansion and big collapse of the photon space through the universe evolution. The big bang from the nothing is the pair production of the matter universe with the positive energy and the partner anti-matter universe with the negative energy from the CPT symmetry. Our universe is the matter universe with the negative charges of electric charge (EC), lepton charge (LC) and color charge (CC). This first universe is made of dark matter -, lepton -, and quark - primary black holes with the huge negative charges which cause the Coulomb repulsive forces much bigger than the gravitational forces. The huge Coulomb forces induce the inflation of the primary black holes, that decay to the super-massive black holes and particles.

Visual servoing technology has been well developed and applied in many automated manufacturing tasks, especially in tools’ pose alignment. To access a full global view of tools, most applications adopt eye-to-hand configuration or eye-to-hand/eye-in-hand cooperation configura-tion in an automated manufacturing environment. All research papers mainly put efforts into developing control and observation architectures in various scenarios, but none of them has dis-cussed the importance of the camera’s location in eye-to-hand configuration. In a manufacturing environment, the quality of camera estimations may vary significantly from one observation loca-tion to another, as the combined effects of environmental conditions result in different noise levels of a single image shot at different locations. In this paper, we propose an algorithm for the camera’s moving policy so that it explores the camera workspace and searches for the optimal location where the images’ noise level is minimized. Also, this algorithm ensures the camera ends up at a subop-timal (if the optimal one is unreachable) location among the locations already searched, with limited energy available for moving the camera. An automated manufacturing application has been sim-ulated and the results show the success of this algorithm’s improvement of observation precision with limited energy.

The article aims to explore social aspects in the area of energy research by using bibliometrics methods and tools. The study is based on the data of Energy Research & Social Science journal publications exported from ScienceDirect database during 2019-2023. Methodologically, the work included clustering of the bibliometric records under consideration. This allowed to identify the main topics of publications and those in which the research of social problems prevails. This stage of the work was carried out using carrot2, an engine for clustering search results. Next, the analysis of publication topics related to social issues research was carried out using VOSviewer — a software tool for visualizing scientific landscapes. The topics of the four clusters obtained at this stage were described by key terms with the maximum total link strength. For the principal ones, a definition was made on the basis of the texts of publications that most fully disclose the meaning of these terms. The 1537 publications in the journal during the period under review deal with many aspects of energy transition research, renewable energy, energy policy, energy justice and energy systems, but only 78 of them are dominated by social issues. The paper reveals the main social issues in the field of energy research: sociology of energy, socio-technical system, community energy, energy democracy, sociology of the future, energy sovereignty, socio-technical imaginary and shows the insufficient attention to this topic, especially to the investment of such research.

Criticism has been directed towards the traditional methods of management accounting employed by organizations thus far, as they fail to adequately address the growing need for competitiveness and sustainable development in a globalized environment. This criticism stems from both economic factors, such as insufficient monitoring of material, energy, and escalating overhead costs, and environmental concerns, where inadequate attention is given to vital information regarding significant environmental aspects, impacts, risks, and damages arising from the organization's activities and processes. Additionally, these methods do not sufficiently support the implementation of a functional environmental management system (EMS). Drawing upon our research in EMS standardization following the international standards ISO 1400X, as well as our knowledge gained during the development of the Slovak Technical Standard (STN) for ISO 14051, this paper presents an innovative model of environmental management accounting. This model is based on the cost accounting of material and energy flows within organizations. It serves as an enhancement framework for organizations with an existing EMS built according to the EN ISO 14001 model, as well as for organizations lacking a formalized EMS based on this standard. Within this paper, we specify, decompose, and apply the new model, focusing on the cost accounting of material-energy flows in a hypothetical organization. We meticulously examine the ten key steps of the model's structure, particularly in terms of costing and the allocation of costs to material, energy, system, and waste management.

Hydrogen-bond (H-bond) energies in 310-helices of short alanine peptides were systematically examined by precise DFT calculations with the negative fragmentation approach (NFA), a modified method based on the molecular tailoring approach. The contribution of each H-bond was evaluated in detail from the 310-helical conformation of total energies (whole helical model; WH3-10 model), and the results were compared with the property of H-bond in a-helix from our previous study. The H-bond energies of the WH3-10 model exhibited tendencies different from those exhibited by the -helix, in that they depended on the helical position of the relevant H-bond pair. H-bond pairs adjacent to the terminal H-bond pairs were observed to be strongly destabilized. The analysis of electronic structures indicated that structural characteristics cause the destabilization of the H-bond in 310-helices. We also found that the longer the helix length, the more stable the H-bond in the terminal pairs of the WH3-10 model, suggesting the action of H-bond cooperativity.

We present simple relations for nuclear stability and nuclear binding energy with respect to three gravitational constants associated with electroweak, strong and electromagnetic interactions.

A new utilization of entropy in the context of buckling is presented. The novel concept connecting strain energy and entropy for a pin-ended strut is derived. This concept rationalizes the ranking of buckling modes based on strain energy under the assumption of given entropy. By assigning identical entropy to all buckling modes, they can be ranked according to their deformation energy. Conversely, with identical strain energy assigned to all modes, ranking according to entropy is possible. Decreasing entropy was found to represent the scaling factors of buckling modes that coincide with the measurement of initial out-of-straightness imperfections in IPE160 beams. Applied to steel plane frames, scaled buckling modes can be used to model initial imperfections. It is demonstrated that the entropy (scale factor) for given energy roughly decreases with the inverse square of the mode index. For practical engineering, the study presents the possibility of using scaled buckling modes of steel plane frames to model initial geometric imperfections. Entropy proves to be a valuable complement to strain energy in structural mechanics.

Internet of things (IoT) is a network of smart things. This indicates the ability of these physical things to transfer information with other physical things. The characteristics of these networks, such as topology dynamicity and energy constraint, challenges the routing problem in these networks. Previous routing methods could not achieve the required performance in this type of network. Therefore, developers of this network designed and developed specific methods in order to satisfy the requirements of these networks. One of the routing methods is utilization of multipath protocols which send data to its destination using routes with separate links. One of such protocols is RPL routing protocol. In this paper, this method is improved using composite metrics which chooses the best paths used for separate routes to send packets. We propose Energy and Load aware RPL (ELaM-IoT) protocol, which is an enhancement of RPL protocol. It uses a composite metric, calculated based on remaining energy, hop count, Link Expiration Time (LET), load and battery depletion index (BDI) for the route selection. In order to evaluate and report the results, the proposed ELaM-IoT method is compared to the ERGID and ADRM-IoT approaches with regard to average remaining energy, and network lifetime. The results demonstrate the superior performance of the proposed ELaM-IoT compared to the ERGID and ADRM-IoT approaches.

Efficient alternatives in energy production and consumption are constantly investigated by increasingly strict policies. In this way, the pollutant emissions that contribute to the greenhouse effect reduce and sustainability of the electricity sector increase. With more than a third of the world's energy consumption, buildings have great potential to contribute these sustainability goals. Additionally, with growing incentives in the Distributed Generation (DG) and Electric Vehicle (EV) industry, it is believed that Smart Buildings (SBs) can be a key in the field of residential energy sustainability in the future. In this work, an energy management system in SBs are developed to reduce the power demanded of a residential building. In order to balance the demand and power provided by the grid, microgrids such as Battery Energy Storage System (BESS), EVs and Photovoltaic Generation panels (PV) are used. Here, a Mixed Binary Linear Programming formulation (MBLP) is proposed to optimize the charge and discharge scheduling of EVs and also BESS. In order to show the efficiency of the model, a case study involving three scenarios and an economic analysis is considered. The results point a 65% reduction in peak load consumption supplied by grid and a 28.4% reduction in electricity consumption costs.

This paper aims at addressing the exploitation of solid-state carriers for hydrogen storage, with attention paid both to the technical aspects, through a wide review of the available integrated systems, and to the social aspects, through a preliminary overview of the connected impacts from a gender perspective. As for the technical perspective, carriers to be used for solid-state hydrogen storage for various applications can be classified into two classes: metal and complex hydrides. Related crystal structures and corresponding hydrogen sorption properties are reviewed and discussed. Fundamentals of thermodynamics of hydrogen sorption evidences the key role of the enthalpy of reaction, which determines the operating conditions (i.e. temperatures and pressures). In addition, it rules the heat to be removed from the tank during hydrogen absorption and to be delivered to the tank during hydrogen desorption. Suitable values for the enthalpy of hydrogen sorption reaction for operating conditions close to ambient (i.e. room temperature and 1-10 bar of hydrogen) are close to 30 kJ·molH2 1. The kinetics of hydrogen sorption reaction is strongly related to the microstructure and to the morphology (i.e. loose powder or pellets) of the carriers. Usually, kinetics of hydrogen sorption reaction is rather fast, and the thermal management of the tank is the rate determining step of the processes. As for the social perspective, various scenarios for the applications in different socio-economic contexts of solid-state hydrogen storage technologies are described. As it occurs with the exploitation of other renewables innovative technologies, a wide consideration of the social factors connected to these processes is needed to assess the extent to which a specific innovation might produce positive or negative impacts in the recipient socio-economic system and to explore the potential role of the social components and dynamics in fostering the diffusion of the innovation itself. Attention has been addressed to the gender perspective, in view of the enhancement of hydrogen-related energy storage systems, intended both in terms of the role of women in triggering the exploitation of hydrogen-based storage as well as to the impact of this innovation in their current conditions, at work and in daily life.