The global focus on geopolymer binder production has increased due to the adoption of waste materials and industrial byproducts. Given the gradual decline of the availability of fly ash and ground granular blast furnace slag (GGBFS) resulting from the decarbonization process in electricity and steel productions, waste clay brick powder (WCBP), could be a viable substitute of these pozzolanic by-products. This research is dedicated to thoroughly investigate the techno-eco-efficiency performance of WCBP when utilized as a geopolymer precursor. The favorable mechanical characteristics exhibited by fly ash-GGBFS-WCBP-based geopolymer binder emphasize the importance of assessing its sustainability alongside its technical viability. The study employed life cycle analysis (LCA), following ISO 14040-44 standards, and using the Simapro software, to evaluate the environmental implications of the use of WCBP-based geopolymer mixtures. Human toxicity emerged as the primary impact. Moreover, the analysis of life cycle costs highlighted key financial factors, with around 65-70% attributed to alkaline activators of the total cost. The production of alkaline activators was identified as a critical point for both environmental impact and economic considerations due to energy consumption. While WCBP-rich samples exhibit a 1.7-0.7% higher environmental impact compared to the control mix (CM), their high mechanical strength and cost-effectiveness make them technologically and economically efficient geopolymer mixes. In conclusion, the portfolio analysis for techno-eco-efficiency affirms that mixes containing 40%, 30%, and 20% WCBP are more efficient than those using 10% and 0% WCBP, respectively.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

New composite with core-shell structure based on magnesium hydride and finely dispersed aluminum powder with aluminum oxide shell was mechanically synthesized. We used magnesium chips to produce magnesium hydride and aluminum wire after exploitation to produce nano-sized aluminum powder. The beginning of the hydrogen release from composite occurred at the temperature of 117°C. The maximum desorption temperature from the MgH₂-EEWAl composite (10 wt.%) is 336°C compared to pure magnesium hydride – 417°C. The mass content of hydrogen in the composite is 5.5 wt.%. The positive effect of aluminum powder produced by the electric explosion of wires method on reducing the activation energy of desorption was demonstrated. Calculations showed that the activation energy of desorption for the composite is 106±1 kJ/mol, compared with pure magnesium hydride, whose activation energy was 155±2 kJ/mol. The results obtained make it possible to expand the possibility of using magnesium and aluminum waste for hydrogen energy.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Rice cultivation is the main agricultural activity in Asia, and it results in an enormous amount of agricultural waste, that are usually disposed-off by burning, causing serious environmental health and climate problems. Pakistan is the tenth largest producer in the world and the fourth exporter of rice in the world. To date, there are no studies targeting Pakistan’s profile monitoring its contribution in open burning emissions from rice straw waste. This study presents the characterization of PCDD/Fs, PCBs and PAHs emissions from three samples of rice straw collected from the main rice cultivation regions of Pakistan (Punjab, Sindh and Azad Jammu and Kashmir) in relation to the role of metal-based agricultural additives. PCDD/Fs, PCBs and PAHs emissions were quantified using a fixed grid system biomass plant and measuring the macro-pollutants online and sampling the organic micro-pollutants and metals in isokinetic mode, followed by ISO and CEN standards methods. In addition, role of agrochemicals was monitored in terms of metal catalysis resulted in POPs emissions. This study provides the characterization of most relevant group of pollutants (metals, PCDD/Fs, PCBs and PAHs) as a result of agricultural waste combustion. The rice straw samples from AJK showed high values of organochlorine micro-pollutants compared to the values followed by samples from Punjab and Sindh, i.e., respectively, ∑PCDD/F (2594>1493>856 pg/Nm³) and ∑PCB (41>38>30 pg/Nm³). Whereas the organic micro-pollutants ∑PAH, indicators of incomplete combustion (PICs), were recorded high in the samples from Sindh followed by Punjab and AJK. This study supports the idea that the phenomena that lead to the formation of PCDD/F and PCB are influenced not only by poor combustion but also by the presence of metal catalysts or precursors in the burned fuel.

The use of plastic in agriculture has become so omnipresent within the industry that it has acquired it own lexicon to become known as ‘plasticulture’. However, since, compared to other industries the quantities consumed are low, little attention is granted to this waste stream. This is the case both with local and international policies even though it bears a close connection to soil health and therefore is a prerequisite to improve the sustainability of food production processes including food security. Using Malta as a case study, the research utilises quantitative and qualitative tools to identify and quantify the most common types of agricultural plastic waste generated and determines the attitudes of farmers towards a collection and recycling scheme. While it identifies that incineration and ploughing of plastic waste as regular practices, it also ascertains the willingness of farmers to acquire more knowledge about more appropriate methods to dispose of this waste stream thus guiding policy makers towards the need to initiate educational measures for farmers to prevent these harmful practices. Through stakeholder interviews the research highlights that the present lack of data is a major hindrance for policy to take account of this waste stream.

The aim of this study is to examine an efficient and environmental friendly process for hydrolyzing starch, an industrial-derived by-product of the potato processing industry, and to use the produced hydrolysates as substrates for methane production. A full factorial experiment was designed and the optimal concentrations of FeSO4·7H2O, H2O2 and temperature were determined obtaining a yield of 99.5%, with a total carbohydrates content equal to 28.65 g, when the input parameters were at their high level: FeSO4·7H2O 1.00g/L, H2O2 0.51 g/L and temperature 70.0oC. The hydrolysis kinetics were also examined revealing that temperature was the most important factor among the three optimization parameters. Furthermore, biodegradability tests were carried out to measure the methane production potential from the produced hydrolysates. The specific methanogenic activity was reached 0.669 g CODCH4/gVSS-day proving the effectiveness of the hydrolysis process and highlighting the potential of this food manufacturing by-product for bioenergy production. A preliminary cost analysis showed that a small investment for utilizing the starch in an existing wastewater treatment facility of a potato processing industry becomes profitable before the end of the 3rd year obtaining a NPV 37.5% higher than the NPV of the current utilization scenario.

The feasibility of using zeolites, synthesized from components found in municipal solid waste fly ash (MSW-FA), as sorbents for the recovery of nutrients (nitrate and phosphate) and heavy metals is critically assessed in this review. The inherent drawbacks of utilising a highly contaminated, variable, and relatively Al- and Si-dilute source such as MSW-FA to synthesize zeolites are discussed, and different methods to extract and decontaminate zeolite precursor materials from MSW-FA are considered. Ways to synthesize tailored zeolites and how their properties as well as the operational conditions impact the adsorption of cations such as ammonium and heavy metals are summarized. The use of surface-modified zeolites to adsorb nitrate and phosphate is also reviewed. And subsequently, approaches to utilise directly or recover for reuse the adsorbed compounds are considered, discussing potential challenges and mitigating measures related to leaching of unwanted compounds from the zeolites. Moreover, the possibility to regenerate the adsorption capacity of the zeolites for multiple adsorption cycles is considered. In the final chapter of the review a more general discussion of the main challenges and existing research gaps is provided, giving directions for recommended studies.

Bitumen is produced from non-renewable natural resources, continuously deplete and intrigues researchers to look for alternative binders. Annually, tons of waste engine oil (WEO) and crumb rubber (CR) are discarded unsustainably and pose a significant environmental threat. Adding these industrial waste products to asphalt provides a safe and cost-effective way for their disposal and improves the bitumen's performance in parallel. This study uses various combinations of waste engine oil and crumb rubber with 60/70 penetration grade bitumen to produce a partially synthetic bitumen. Adhesion being one of the critical characteristics of the bituminous binder has been assessed using the bitumen bond strength test along with physical and rheological properties. Results showed that waste engine oil with crumb rubber inclusion increases penetration and decreases the softening point, viscosity, complex modulus, and bonding strength. Additionally, polyphosphoric acid (PPA) in smaller dosages was also incorporated into the optimum percentage of CR + WEO to improve the properties of the binder. The results confirm that binder modification with waste engine oil and crumb rubber can be more effective with PPA. It is concluded that 35% of waste can replace the virgin binder giving a cost-effective and environmentally friendly solution.

The extensive utilization of rebar during the construction of the project generates immense rebar waste, leading to increased construction costs and significant greenhouse gas emissions. Various approaches have been explored focusing on the minimization of rebar-cutting waste, such as optimizing cutting patterns, lap splice position, and special-length rebar utilization. Nonetheless, reducing rebar usage by minimizing the number of splices remains uninvestigated. In response to these issues, a two-stage optimization algorithm was developed, prioritizing special-length rebar to achieve near-zero rebar-cutting waste of less than 1% and concurrently reduce rebar usage, thereby promoting sustainable construction practices. The two-stage algorithm presented in this study involves the optimization of the lap splice position for the continuous rebar with a reduction of splices number. Furthermore, it integrates a special-length minimization algorithm for the additional rebars. Applying the algorithm to beam structures in a small-sized factory building project led to a notable reduction of 29.624 tons of rebar, equivalent to 12.31% of the total purchased quantity. Greenhouse gas emissions were reduced by 102.68 tons, and associated costs decreased by USD 30,256. A rebar-cutting waste of 0.99% which is near zero was achieved. These findings highlight the significant potential of the proposed algorithm in reducing rebar waste and facilitating sustainable construction practices. In addition, the application of the proposed algorithm in reinforced concrete construction projects will amplify the associated advantages accordingly.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

Despite the development of biorefinery processes, so far this area does not take into account the possibility of coupling the “conventional” composting process with the production of biochemicals. However, net carbon monoxide (CO) production has been observed during bio-waste composting. So far, O2 concentration and temperature have been identified as main variables influencing CO formation. This study aimed to investigate the CO net production during bio-waste composting under controlled laboratory conditions, depending on different aeration rates and temperatures. A series of composting processes were carried out in conditions ranging from ~psychrophilic to thermophilic (T=35, 45, 55, and 65°C) and an aeration rate of 2.7, 3.4, 4.8, and 7.8 L‧h-1. The highest concentrations of CO in each thermal variant was achieved with oxygen deficit (aeration rate 2.7 L‧h-1); additionally, CO levels increased with temperature, reaching ~300 ppm at 65°C. Production of CO in mesophilic and thermophilic conditions draws attention to the biological CO formation by microorganisms capable of producing the CODH enzyme. Further research on the CO production efficiency in these thermal ranges is necessary with the characterization of the microbial community and analysis of the ability of the identified bacteria to produce the CODH enzyme and convert CO from CO2.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Over the past few decades, the quantity of construction waste has steadily risen in tandem with the expansion of construction activities and the rapid pace of development and urbanization. This problem is rooted in the practice of delivering materials to construction sites without totally using them for their intended purpose. The primary aim of the JIT tactic is to ensure that the precise materials required for production are available at the precise location, exact time, and appropriate quantity, thereby facilitating timely production. Presently, the use of ready-mix concrete is the most typical instance of a just-in-time construction process Developed countries have benefitted immensely from the use. However, the reverse is the case in developing countries like Nigeria, where indigenous contractors still employ traditional in-situ concreting even when faced with restrictive site space. This study focuses on investigating Ready-mix concrete, to project its immense benefits and effectiveness in minimizing lean construction waste. A survey research design and case study were adopted for this study, with the population being the management staff of construction firms in Lagos State, Nigeria. The questionnaire was used to collect data and the targeted respondents were purposively selected from the population. A total number of 112 questionnaires were administered with a response rate of 51%. Percentage, mean, standard deviation, and ANOVA were used to analyze the data. The mean value is above 3 on a Likert Scale of 5, while faster construction speed and uniform quality of concrete are the topmost benefits derived from adopting Ready-mix Concrete in Nigeria. The Case study also revealed the effectiveness of Ready-mix concrete in minimizing the two lean construction wastes that were examined, namely; waste of overproduction and waste of waiting. It is recommended Just-in-Time technique should be extended to other construction materials aside from concrete to improve waste minimization through the adoption of an overall JIT policy for the construction process.

The Metabolic Food Waste [MFW (kg of food)], first time developed in 2016 as a new indicator by Serafini and Toti, indicates the amount of food consumed over the nutritional requirements and the impact of this overconsumption on the environment. It is necessary to identify the causes and to develop potential methods to prevent and reduce MFW, at the same time with increasing consumer awareness about unsustainable diets and changing diet habits toward more environmentally conscious consumption patterns. By analysing and corroborating external data available for food waste, nutritional requirements, environmental impact of food waste and consumer behaviour, we identified as primary causes for MFW the lack of nutritional education and little understanding of the nutritional requirements amongst all categories of consumers, no access to appropriate food resources or reduced availability of fresh produced food. We conclude that for the quantification of the negative impact of MFW on both the environment and human health, we need a decisive action to raise consumer awareness for healthy and sustainable diets, together with an uniform worldwide distribution of the nutritious food.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

One of the potential sources of rare-earth elements (REEs) is the solid waste from alumina industry - bauxite residue, known as “red mud” (RM). The main REEs from the raw bauxite are concentrated in RM after the Bayer leaching process. The earlier worldwide studies were focused on the scandium (Sc) extraction from RM by concentrated acids to enhance the extraction degree. This leads to the dissolution of major oxides (Fe2O3 and Al2O3) from RM. This article studies the possibility of selective Sc extraction from alkali fusion red mud (RMF) by diluted nitric acid (HNO3) leaching at pH ≥ 2 to prevent co-dissolution of Fe2O3. RMF samples have been analyzed by X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), electron probe microanalysis (EPMA), and inductively coupled plasma mass spectrometry (ICP-MS). Sc extraction has been found to be 71.2 % at RMF leaching by HNO3 at pH=2 and at 80 °C during 90 min. The kinetic analysis of experimental data by the shrinking core model has shown that Sc leaching process is limited by the interfacial diffusion and the diffusion through the product layer. The apparent activation energy (Ea) was 19.5 kJ/mol. We have established that according to EPMA of RMF, Sc is associated with iron minerals; it could act as the product layer. The linear dependence of Sc extraction of magnesium (Mg) extraction has been revealed. This fact indicates that Mg can act as a leaching agent of Sc presented in RMF by ion-exchangeable phase.

A winemaking waste was used as a precursor of activated carbon used in hazardous Cr(VI) removal from solutions. The preparation process consisted of a hydrothermal process, and a chemical activation, of the resulting product, with KOH. The adsorption results showed that the adsorption of Cr(VI) on the obtained activated carbon is strongly dependent on the stirring speed applied to the carbon/solution mixture, pH of the solution, and temperature. The equilibrium isotherm was well fitted to the Langmuir type-II equation, whereas the kinetic can be described by the pseudo-second-order kinetic model. Thermodynamic studies revealed that Cr(VI) adsorption was an exothermic and spontaneous process. Finally, desorption experiments showed that Cr(VI) was effectively desorbed using hydrazine sulfate solutions, and at the same time, the element was reduced to the less hazardous Cr(III) oxidation state.

Most of the municipalities in the Gulf region are facing performance related issues in their municipal solid waste management (MSWM) systems. They lack to possess a deliberate inter-municipality benchmarking processes. Instead of identifying the performance gaps for their key components (e.g., personnel productivity, operational reliability, etc.) and adopt proactive measures, the municipalities primarily rely on an efficient emergency response. A novel hierarchical modeling framework, based on deductive reasoning, is developed for performance assessment of MSWM systems. Fuzzy rule based modeling using Simulink-MATLAB was used for performance inferencing at different levels, i.e., component, sub-components, etc. The model is capable of handling the inherent uncertainties due to limited data and imprecise knowledge base. The model’s outcomes can exclusively assist the managers working at different levels of organizational hierarchy for effective decision-making. Performance of the key component, assists the senior management to assess the overall compliance level of performance objectives. Subsequently, operation management can hone in the sub-components to acquire useful information for intra-municipality performance management. While, individual indicators are useful for inter-municipality benchmarking. The model has been implemented on two municipalities operating in Qassim Region, Saudi Arabia. The results demonstrate the model’s pragmatism for continuous performance improvement of MSWM systems in the country and elsewhere.

In the industrial production of olive oil, both solid wastes and those produced from their incineration are a serious environmental problem since only 20% w/w of the fruit becomes oil and the rest is waste, mainly orujo and alperujo. A key aspect to transform these wastes into an important source of energy such as pellets is to recognize the most appropriate time of the year for waste drying, with the objective of minimizing the environmental impact of the volatile compounds contained in the waste. In this work, the emissions produced during thermal-mechanical drying were studied along a period of six months of waste storage in which alperujo and orujo were stored in open containers under uncontrolled environmental conditions. The studied emissions were produced when both wastes were dried in a pilot rotary drying trommel at 450ºC to reduce their initial humidity of around 70-80% w/w to 10-15% w/w. Results indicated that when the storage time of the wastes in uncontrolled environments increases, the emission of odorant compounds during drying also increases as a consequence of the biological and chemical processes occurring in the containers during waste storage. The main odorant VOCs were quantified monthly for six months at the outlet of the drying trommel. It was determined that the drying of this type of waste can be carried out properly until the third month of storage. Afterwards, the concentration of most VOCs produced widely exceeded the odor thresholds of selected compounds.

Efficient use of agricultural wastes and by-products, basically transforming waste materials into value added products, is considered as pivotal for an effective bioeconomy strategy for the rural development. To this scope, citrus waste management represents a major issue for citrus processors but, at the same time, it embodies a potentially unexploited resource for the rural sustainable development. This study focuses on analyzing the current management of citrus waste in South Italy and identifying the determinants and barriers that may affect an entrepreneur’s choice on the destination of citrus waste. Citrus processors’ preferences about the contract characteristics needed to take part in a co-investment scheme have been investigated. Both analyses are preliminary steps to design an innovative and sustainable citrus by-product supply chain. Results show that the distance between the citrus processors and the citrus by-products plant is one of the main criteria for choosing alternative valorization pathways. Moreover, the required guaranteed capital, the short duration of the contract, and low risk are contract scheme characteristics that improve entrepreneurs’ willingness to co-invest in the development of a citrus waste multifunctional plant.

DR2B and DR2C extracts, from peel of commercially and physiologically ripe eggplants, were studied for the antioxidative cytoprotective properties and anti-HSV-1 activity, in line with the evidence that several antioxidants can impair viral replication by maintaining reducing conditions into the host cells. The antioxidative cytoprotective effects against tBOOH-induced damage was assessed in Caco2 cells, while the antiviral activity was studied in Vero cells; phenolic and anthocyanin fingerprint was characterized by integrated phytochemical methods. Results highlighted different compositions of the extracts, with chlorogenic acid and delphinidin-3-rutinoside as the major constituents; other peculiar phytochemicals were also identified. DR2C resulted able to partly counteract the tBOOH-induced cytotoxicity, with a remarkable lowering of lactate metabolism under both normoxia and hypoxia. DR2B and DR2C reduced ROS production, possessed scavenging and chelating properties. Interestingly, DR2C increased intracellular GSH levels. Furthermore, DR2C inhibited the HSV-1 replication when added for 24 h after viral adsorption, as also confirmed by the reduction of many viral proteins expression. Since DR2C was able to reduce NOX4 expression during HSV-1 infection, its antiviral activity may be correlated to its antioxidant properties. Although further studies are needed to better characterize DR2C activity, the results suggest this extract as a promising new anti-HSV-1 agent.

The efficiency of cold steel rolling depends mainly on the quality of the metal-working coolant (MWC) and its cost. In this connection, it is actual to search for new compositions of lubricants and emulsions, which provide the lowest values of the friction coefficients in deformation zone and are obtained by waste recycling in other industries. In this study we have developed new compositions of the MWC on basis of mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The new compositions of MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 100 mm. The efficiency of new MWC during cold rolling of brass L63 samples was determined by factor of metal stretch forming λ. We found the new metal-working coolants to show the most efficiency under higher cobbing that provides the highest metal stretch forming. The composition with 30 % of mono- and diglycerides is the most effective because it provides the minimum coefficient of friction that leads to increase of factor of metal stretch forming. Thereby the metal-working coolants on basis of mono- and diglycerides obtained from the wastes of sunflower oil production can be recommended for use in strip rolling of copper-zinc alloys because of a low cost, availability and high efficiency.

The growing use of proton-exchange membrane fuel cells (PEMFC) in hybrid propulsion systems, aimed at replacing traditional internal combustion engines and reducing greenhouse gas emis-sions. Effective power distribution between the fuel cell and the energy storage system (ESS) is crucial, which has led to a growing emphasis on developing energy management systems (EMS) to efficiently implement this integration. To address this goal, this study examines the performance of a fuzzy logic rule-based strategy for a hybrid fuel cell propulsion system in a small hydro-gen-powered passenger vessel. The primary objective is to optimize fuel efficiency, with particular attention to reducing hydrogen consumption. The analysis is carried out under typical operating conditions encountered during a river trip. Comparisons between the proposed strategy with other approaches —control-based, optimization-based and deterministic rule-based— are con-ducted to verify the effectiveness of the proposed strategy. Simulation results indicated that EMS based on fuzzy logic mechanisms was the most successful in reducing fuel consumption. The superior performance of this method stems from its ability to adaptively manage power distri-bution between the fuel cell and energy storage systems.

Sustainable energy development (SED) is a crucial component of the Sustainable Development Goals (SDG), aiming to maintain economic and social progress while protecting the environment and mitigating climate change’s effects. SED serves as a transition paradigm for sustainable development, providing a blueprint for energy peace and prosperity for people and all uses. This article presents the history of SED and then uses a critical discourse approach to summarize existing review studies in SED. Ten interlinked themes of SED are identified, with two of them considered to be among the least studied in existing SED reviews and in the current global discussion around climate change. This study explores these two themes, which include energy financing and the need for 100% renewable energy (RE), a sub-theme of decarbonization strategy working towards the 1.5–2.0 °C scenario. The study suggests that the current G20 countries’ contributions, if maintained continuously per annum, in addition to 80% more funding from private investment compared to the amount in the 1.5 °C scenario financial requirements for clean energy, are sufficient to limit global warming. In addition to the present drive for 100% RE, the article also discusses emerging issues, such as energy storage options with an indication of hydrogen as the most promising, other energy-related development agendas, and the need for regional security stability to prevent energy wars. Selected SED decarbonization strategies are presented across the power, transport, building, and industrial sectors. The study concludes with progress and directions for future research, mainly the need for re-defining nationally determined contribution (NDC) through an emissions budgeting and centralized global or regional emissions stock-taking strategy working towards the 1.5 °C scenario.

Conventional methods of climate change (CC) mitigation have not ‘bent the curve’ of steadily rising annual anthropic CO2 emissions or atmospheric concentrations of greenhouse gases. This study reviews the present position and likely future of such methods, using recently published literature with a global context. It particularly looks at how fast they could be implemented, given that the limited time available for avoiding catastrophic CC (CCC). The study then examines solar geoengineering, an approach often viewed as complementary to conventional mitigation. The review next introduces equity considerations, and shows how this will shorten even further the time available for effective action for CC mitigation. The main findings are as follows. Conventional mitigation approaches will be implemented too slowly to be of much help in avoiding CCC, partly because some suggested technologies are infeasible, while others are either of limited technical potential, or, like wind and solar energy, cannot be introduced fast enough. Because of these problems, solar geoengineering is increasingly advocated as a quick-acting and effective solution. However, it could have serious side effects, and given that there will be winners and losers at the international as well as the more regional level, political opposition may make it difficult to implement. The conclusion is that global energy consumption itself must be rapidly reduced to avoid catastrophic climate change.

Piezoelectric nanotransducers may offer key advantages in comparison with conventional piezoelectrics, including more choices for types of mechanical input, positions of the contacts, dimensionalities and shapes. However, since piezo-semiconductive nanostructures are generally much easier to fabricate and integrate into functional systems than insulating materials, modeling becomes significantly more intricate and the effects of free charges have been considered only in a few studies. The available reports are complicated by the absence of proper nomenclature and figures of merit. Besides, some analyses are incomplete. For instance, the local piezopotential and free charges within axially strained conical piezo-semiconductive nanowires have only been systematically investigated for very low doping (1016 cm-3) and under compression. Here we give the definitions for the enhancement, depletion, base and tip piezopotentials, their characteristic lengths and both the tip-to-base and the depletion-to-enhancement piezopotential-ratios. As an example, we use these definitions for analyzing the local piezopotential and free charges in n-type ZnO truncated conical nanostructures with different doping levels (intrinsic, 1016 cm-3, 1017 cm-3) for both axial compression and traction. The definitions and concepts presented here may offer insight for designing high performance piezosemiconductive nanotransducers.

Tropical regions face unique challenges in building sustainability due to high temperatures, humidity, and heavy rainfall. While building energy regulations are essential for promoting energy efficiency, their effectiveness in addressing tropical climate conditions needs to be studied more. This research aims to systematically investigate tropical building sustainability issues and evaluate the impacts of building energy regulations on these challenges. The study will identify gaps in current regulations by analyzing existing research and recommend strategies for developing more comprehensive frameworks that promote sustainable building practices in tropical regions. This research contributes to developing effective policies and strategies for achieving sustainable and energy-efficient built environments in tropical climates.

The integration of solar energy systems with agricultural practices, known as agrivoltaic systems, presents a promising solution for advancing sustainable food and energy production. This approach involves installing photovoltaic panels on agricultural lands, which allows for simultaneous crop cultivation and energy generation. Agrivoltaic systems offer a dual benefit: they enhance land use efficiency by utilizing the same area for both solar power generation and crop production, and they contribute to sustainable energy transitions. This abstract explores the benefits and challenges associated with agrivoltaic systems. Key advantages include increased land productivity, reduction in water usage due to shading effects, and potential economic gains from dual income streams. Furthermore, these systems can mitigate land use conflicts by combining food production with renewable energy generation. However, there are challenges to address, including the potential for decreased crop yields under solar panels, the need for appropriate system design to balance energy generation and agricultural needs, and the economic feasibility of initial investment and maintenance. The integration of agrivoltaic systems represents a critical step toward achieving sustainable development goals by promoting environmental stewardship and resource efficiency. Future research and advancements in technology are essential to optimize system performance and maximize benefits for both agriculture and energy sectors.

The International Renewable Energy Agency (IRENA) was established in 2009 and in 2024, its membership increased to 168 members plus the European Union countries. The purpose of IRENA is to promote the adoption of renewable energy across all industries in the world. Despite the utilization of renewable energy in sectors like power generation and construction, its application in other industries remains limited. Therefore, a literature review study was conducted to investigate the cost and other spatial constraints associated with renewable energy resources, including modeling and optimization techniques that could offer viable solutions to the future challenges faced by the renewable energy production systems. This paper has summarized the result of this study with a focus on the significance of modeling and optimization techniques in energy conservation to highlight the untapped potential for leveraging renewable energy resources in industrial applications. This paper also examined a few case studies from various regions of the world, demonstrating the promising opportunities for research in the modeling and optimization of renewable energy management systems.

Building integrated photovoltaics (BIPV) consists of PV panels that are integrated into the building as part of the construction. This technology has advantages such as the production of electricity without necessary additional land area. This paper provides a literature review about the recent developments in urban building energy modelling, including tools and methods, and how they can be used to predict the effect of PV systems on building outdoor and indoor environments. It is also intended to provide a critical analysis on how PV systems affect the urban environment, both from an energy and a comfort point of view. The microclimate, namelly the urban heat island concept, is introduced and related with the existence of PV systems. It is concluded that urban building energy modelling (UBEM) can be effective to study the performance of PV systems in the urban environment. It allows to simultaneously predict the building energy performance and the microclimate effect. However, there is a need to develop new methodologies to overcome the challenges associated to UBEM, especially in what concerns non-geometric data, which leads to a major source of errors. and to find an effective method to predict the effect of PV systems in the urban environment.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

Geoenvironmental engineering involves defining solutions for complex problems, such as containment systems management, contaminant transport control, wastewater management, remediation of contaminated sites and valorization of geomaterials and wastes. In the last years, energy harvesting (EH) - or energy scavenging - methods and technologies have been developed to reduce the dependence on traditional energy sources, namely fossil fuels, and nuclear power, also responding to the increase of energy demands for human activities and to fulfill sustainable development goals. EH in geoenvironmental works and surrounding soil and water environment include a set of processes for capturing and accumulating energy from several sources considered deemed wasted or unusable associated to soil dynamics, stress and strain of geomaterials, hydraulic, vibrations, biochemical, light, heating and wind sources can be potential EH systems. Therefore, this work presents a review of the literature and critical analysis on the main opportunities for EH capturing, accumulating and use in geoenvironmental works, among basic electric concepts and mechanisms, analyzing those works in complex conditions involving biological, chemical, mechanical, hydraulic, and thermal coupled actions, concluding with the main investigation and challenges within geoenvironmental aspects for EH purpose.

In this paper, spacetime is defined as the absolutely invariant homogeneous "coordinate spacetime" frame and its modulation by the relatively variable non-homogeneous "metric spacetime" under its constraints. This modulation is caused by matter and motion, and carries the function of transmitting interactions, reflecting the diffeomorphism invariance and Lorentz invariance. This inhomogeneous spacetime concept makes the medium nature of spacetime more obvious and avoids the problem of "path dependence" caused by the concept of curved spacetime. In this paper, it is argued that all energy-momentum has internal spatio-temporal properties, and all interactions must be transmitted through spacetime metrics. On this basis, a converging and dispersing cyclic multiverse model is proposed. This model of the universe is inevitable as long as there are two macroscopic manifestations of the matter of the universe, namely, gravitation induced convergence and "explosive" dispersion caused by different factors. The new cosmic model matches the observed accelerated "expansion" of the universe and no longer requires the dark energy hypothesis.

The benchmarking of hotel energy use comprehensively identifies the controllable and uncontrollable factors affecting energy performance, including building characteristics, management strategies, operations, and maintenance systems. Other factors include climatic conditions, floor areas, operating hours, occupancy rates, and guest populations. A benchmarking study on energy consumption patterns in significant hotels (each with less than 100 rooms and an average staff strength of 40 employees), situated in the university town of Nsukka (longitude 70 23' E, latitude 60 52' N), Nigeria, was performed using the data envelopment analysis (DEA) methodology. DEA, a linear programming technique that measures the relative performances of units, was chosen as a benchmarking methodology due to its ability to handle multiple inputs and outputs. Following a correlation test, energy use intensity, diesel consumption, and the number of employees were selected as the analysis inputs, while the occupancy rate was chosen as the output variable. Data on these variables spanning 12 months were collected using questionnaires, interviews, site visits, and oral conversations with hotel managers to ensure validity. Grid-supplied electricity accounted for most of the hotels' energy needs, followed by diesel used in generators. More than 70% of the electricity use was for HVAC. From the DEA, Hotel 3 (DMU H3) had a technical efficiency score of 1, whereas adjustments were recommended for improving the efficiency scores of the other hotels, which were deemed inefficient. DMU H7 had the lowest efficiency score (0.474) and the highest identified savings for electricity and diesel. The analysis also revealed that occupancy rates were generally low in the months of June and July, coinciding with the high rainfall season with its accompanying decline in outdoor activities. Consistent with this, electricity consumption was highest in the Christmas and Easter holiday months of December, January, and April following increased travel-related activities.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

Wireless energy harvesting (EH) communication has long been considered a sustainable networking solution. However, it has been limited in efficiency, which has been a major obstacle. Recently, strategies such as energy relaying and borrowing have been explored to overcome these difficulties and provide long-range wireless sensor connectivity. In this article, we examine the reliability of the wireless-powered communication network by maximizing the net bit rate. To accomplish our goal, we focus on enhancing the performance of hybrid access points and information sources by optimizing their transmit power. Additionally, we aim to maximize the use of harvested energy by energy-harvesting relays for both information transmission and energy relaying. However, this optimization problem is complex as it involves non-convex variables and requires combinatorial relay selection indicators optimization for decode and forward (DF) relaying. To simplify this problem, we utilize the Markov decision process and deep reinforcement learning framework based on the deep deterministic policy gradient algorithm. This approach enables us to tackle this non-tractable problem, which conventional convex optimisation techniques would be difficult to solve in complex problem environments. The proposed algorithm significantly improves the end-to-end net bit rate of the smart energy borrowing and relaying EH system by 13.22%,27.57%, and 14.12% compared to the benchmark algorithm based on borrowing energy with an adaptive reward for Quadrature Phase Shift Keying, 8-PSK, and 16-Quadrature amplitude modulation schemes, respectively.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.

The optimization of the energy grid is a critical task for ensuring a sustainable and efficient energy future. Deep machine learning techniques have the potential to improve energy grid optimization by predicting energy demands and supplies, optimizing energy production and distribution, and detecting and preventing fraud. However, there are also several challenges associated with the use of deep machine learning in energy grid optimization. These include the lack of standardized datasets and data quality issues, interpretability and explain-ability of machine learning models, ethical and social implications of using machine learning, and integration with existing energy infrastructure and regulatory frameworks. Having a clear understanding that continued research and developments in deep learning applications to energy field are crucial for achieving a sustainable and efficient energy future. This paper therefore reviewed existing literature for challenges and opportunities associated with deep machine learning in energy grid optimization; and highlights the importance of continued research and development in the field. The paper found out that opportunities for future research in deep machine learning for energy grid optimization include advancements in machine learning algorithms and techniques, development of new datasets and data collection methods, integration of machine learning with other emerging technologies. It also established needs for collaborative research and public-private partnerships.

We use a recently proposed formulation of quantum mechanics based, not on potential functions but rather, on orthogonal energy polynomials. In this context, the most important building block of a quantum mechanical system, which is the wavefunction at a given energy, is expressed as pointwise convergent series of square integrable functions in configuration space. The expansion coefficients of the series are orthogonal polynomials in the energy; they contain all physical information about the system. No reference is made at all to the usual potential function. We consider, in this new formulation, few representative problems at the level of undergraduate students who took at least two courses in quantum mechanics and are familiar with the basics of orthogonal polynomials. The objective is to demonstrate the viability of this formulation of quantum mechanics and its power in generating rich energy spectra illustrating the physical significance of these energy polynomials in the description of a quantum system. To assist students, partial solutions are given in an appendix as tables and figures.

Considering the actual world economical trends, one of the most important questions is now and in the future: how to reduce power consumption of electronic systems. Since the invention of computers, the electrical energy consumption step by step increased. Now when not only computers, but electric vehicles, robots, automation, and unmanned aerial vehicles play a very important role of our life, the main problem of system designers is how to reduce energy consumption in these systems. But also the existing already working systems must be revised in order to decrease their electric power consumption. The importance of this subject (energy control) shows that a huge number of research publications and survey papers deal with it. Just focusing on the last one or two years (2021 and 2022) the search hit 221000 titles (103000 hits only in 2022). Analyzing all the research areas is almost impossible, but focusing on some important research subjects, where one of the main topic is “energy saving methods” can give an overview about the subject. The paper focuses on the area of industrial robotic systems, electric vehicles, and embedded systems.

It is a truism that whole energy system models underpin the development of policies for energy system decarbonisation. But recent reviews have thrown doubt on the appropriateness of such models for addressing the multiple goals for future energy systems, in the face of emergent real-world complexity and the evolution of stakeholder’s priorities. Without an understanding of the changing priorities of policy makers and expectations of stakeholders for future systems, system objectives and constraints are likely to be ill-defined, and there is a risk that models may be inadvertently instrumentalised. Adopting a system architecture perspective, the authors have undertaken a three-year programme of research to explore strategies for decarbonising heat in the UK, with interaction with and elicitation of needs from stakeholders at its heart. This paper presents the procedure, methods, and results of an exercise in which experts from stakeholder organisations across the energy system were interviewed. Analysis of interview data reveals two broad approaches to heat decarbonisation which can be broadly defined as either adaptive or transformative. Specific insights gained from these interviews enabled our modelling teams to refocus their work for exploration with a wider circle of stakeholders. Results suggests that this iterative approach to formalising model-policy interaction could improve the transparency and legitimacy of modelling and enhance its impact on policy making.

Law of conservation of energy is the most well-established law of modern physics. But, inflationary cosmological model which assumes the universe to be created from a point of singularity has not been able to identify the source of energy for creation of this universe. As per uncertainty principle, a quantum vacuum fluctuation can at most create energy of ~10^-8 kg in a Planck time of ~5.4 ×10^-44 s whereas total positive energy due to matter/vacuum existing in the universe is more than ~10⁵⁴ kg. To solve this problem, we have recently published a new cosmological model (Biswaranjan Dikshit, Canadian Journal of Physics, 100, 218-225, [2022]) in which we have mathematically proved that the total energy of the universe can be zero right from the beginning of the universe to till date due to negative gravitational potential energy and thus law of conservation of energy can be satisfied during creation of the universe from nothing. In this article, starting from a simple argument, we explain why net energy of the universe can be zero only in our model, not in standard cosmological model. An interesting fact pointed out in this paper is that the factor ~10⁶² by which radius of universe has increased from its starting value of ~10^-36 m to present value of ~10²⁶ m is same as the factor by which positive energy has increased from Planck energy ~10^-8 kg to present value ~10⁵⁴ kg. This is in agreement with our new model that predicts the positive energy of universe to be proportional to the radius of universe. We also bring out to the notice that zero energy universe is possible only if smallest possible length in nature is, l_min=l_p(π/2)^1/2 = 2.0×10^-35 m. Minimum possible length is important in theory of quantum gravity and string theory.

Intending to analyze the role of nuclear power in an integrated energy system, we used the IESA-Opt-N cost minimization model focusing on four key themes: system-wide impacts of nuclear power, uncertain technological costs, flexible generation, and cross-border electricity trade. We demonstrate that the Levelized Cost of Energy (LCOE) alone should not be used to demonstrate the economic feasibility of a power generation technology. For instance, under the default techno-economic assumptions, particularly the 5% discount rate and exogenous electricity trade potentials, it is cost-optimal for the Netherlands to invest in 9.6 GWe nuclear capacity by 2050. However, its LCOE is 34 €/MWh higher than offshore wind. Moreover, we found that nuclear power investments can reduce demand for variable renewable energy sources in the short term and higher energy independence (i.e., lower imports of natural gas, biomass, and electricity) in the long term. Furthermore, investing in nuclear power can reduce the mitigation costs of the Dutch energy system by 1.6% and 6.2% in 2040 and 2050, and 25% lower national CO₂ prices by 2050. However, this cost reduction is not significant given the odds of higher nuclear financing costs and longer construction times. In addition, this study has shown that lower financing costs (e.g., EU taxonomy support) considerably reduce the relevance of nuclear cost uncertainties on its investments. Furthermore, we demonstrate that the economic feasibility of national nuclear power investments can vary considerably depending on the cross-border electricity trade assumptions. Additionally, we found that lowering the cost of small modular reactors has more impact on their economic feasibility than increasing their generation flexibility. In conclusion, under the specific assumptions of this study, nuclear power can play a complementary role (in parallel to the wind and solar power) in supporting the Dutch energy transition from the sole techno-economic point of view.

Airborne wind energy (AWE) systems use tethered flying devices to harvest higher-altitude winds to produce electricity. For a successful deployment of these systems, it is crucial to understand how the public perceives them. If public concerns about the technology are not taken seriously, implementation could be delayed or, in some cases, prevented, resulting in increased costs for project developers and a lower contribution of the sector to renewable energy targets. This literature review assessed the current state of knowledge on public responses to AWE. An exhaustive literature search led to the identification of 40 relevant publications that were reviewed. The literature assumed that the safety, visibility, acoustic emissions, ecological impacts, and the siting of AWE systems shape public responses to the technology. The reviewed literature views people’s responses to AWE very optimistically but lacks scientific evidence to back up its claims. It seems to overlook that the influence of AWE’s characteristics (e.g., visibility) on public responses will also depend on a range of situational and psychological factors (e.g., people’s general attitude towards AWE, the public’s trust in project developers). Therefore, empirical social scientific research is needed to increase the field’s understanding of public responses to AWE and thereby facilitate deployment.

Integration of battery energy storage in photovoltaic (PV) systems can reduce the electricity costs and provide desirable flexibility and reliability to these systems decreasing renewable energy fluctuations. This paper presents a review of the PV-battery application in Brazil, highlighting the challenges and prospects based on the state-of-art. A PV-battery systems description is presented in this work, as well as the most applied battery technology and its comparison. The paper also describes the set of applications such as voltage and frequency regulation, renewable energy integration, power quality, etc. In the Brazilian scenario, there are applications of PV-battery systems, most of them part of research and development projects (R&D’s), and some real cases are shown, including its goals, applied equipment, operation modes, strategies, and perspectives. Additionally, this work evaluates the Brazilian scenario regarding the energy storage systems implementation challenges, such as regulatory barriers, business models, and opportunities for R&D in the energy market. In conclusion, it is need develop proper regulatory models to expand PV-battery systems and make them visible to the agents in the electricity sector.

Information and communication technologies (ICT) are increasingly permeating our daily life and we ever more commit our data to the cloud. Events like the COVID-19 pandemic put an exceptional burden upon ICT infrastructures. This involves increasing implementation and use of data centers, which increased energy use and environmental impact. The scope of this work is to take stock on data center impact, opportunities, and assessment. First, we estimate impact entity. Then, we review strategies for efficiency and energy conservation in data centers. Energy use pertain to power distribution, IT-equipment, and non-IT equipment (e.g. cooling): Existing and prospected strategies and initiatives in these sectors are identified. Among key elements are innovative cooling techniques, natural resources, automation, low-power electronics, and equipment with extended thermal limits. Research perspectives are identified and estimates of improvement opportunities are presented. Finally, we present an overview on existing metrics, regulatory framework, and bodies concerned.

The rapid development of China's economy has led to a rapid increase in energy production and use. Among them, the excessive consumption of coal in fossil energy consumption is the leading cause of air pollution in China. This paper incorporates renewable energy innovation, fossil energy consumption and air pollution into a unified analysis framework, and uses spatial measurement models to investigate the spatial effects of renewable energy green innovation and fossil energy consumption on air pollution in China, and decomposes the total impact into direct and indirect effects. influences. The empirical results show that China's air pollution, renewable energy green innovation and fossil energy consumption are extremely uneven in geographical space, generally showing the characteristics of high in the east and low in the west, and showing a strong spatial aggregation phenomenon. Fossil energy consumption will lead to increased air pollution, and the replacement of fossil fuels with clean and renewable energy is an important means of controlling pollution emissions. The direct and indirect effects of renewable energy green innovation on air pollution are significantly negative, indicating that renewable energy green innovation not only suppresses local air pollution, but also suppresses air pollution in neighboring areas. The consumption of fossil energy will significantly increase the local air pollution, and the impact on the SO2 and Dust&Smoke pollution in the adjacent area is not very obvious. It is recommended to strengthen investment in renewable energy green innovation, reduce the proportion of traditional fossil energy consumption, and pay attention to the spatial connection and spillover of renewable energy green innovation.

The stability between the limited available energy resources and their consumption is an important concern of the modern world. The study deals with the development of the methods for measuring the energy performance of different renewable and non-renewable resources used for electricity generation with the help of an energy performance indicator called the Primary Energy Factor (PEF). This study takes account of all energy stages from the resources extraction to its transportation, conversion, combustion and then finally to utilization. The study conducted a comparative approach to calculate the PEF values of electricity generated in South Korea from the period of 1980 to 2017. Four different methodologies namely Eurostat methodology, Life cycle methodology, Modified Eurostat methodology, and upper-end methodology have been used. A set of Programs has been written in MATLAB to calculate the i. PEF values of electricity generated. ii. Impact of different renewable and non-renewable energy sources on PEF values. iii. Future trend of PEF values of electricity in South Korea At the national and local level, this study will help the government and other law-making institutions to make policies regarding annual purchase consumptions of energies by different industrial, residential, public and transportation sectors and at the Global level, the implementation of this study will be the catastrophe of maintaining the stability between the available energy resources, and consumptions. This, in turn, will lead to suitable living conditions for future generations

Energy taxation is used globally as a means of energy policy. Energy tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy taxes. Results of this study show that South Korea’s energy taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy taxation. However, energy taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy taxation.

In Electrified Vehicles, the cost, efficiency, and durability of electrified vehicles are dependent on the energy storage system (ESS) components, configuration and its performance. This paper, pursuing a minimal size tactic, describes a methodology for quantitatively and qualitatively investigating the impacts of a full bandwidth load on the ESS in the HEV. However, the methodology can be extended to other electrified vehicles. The full bandwidth load, up to the operating frequency of the electric motor drive (20 kHz), is empirically measured which includes a frequency range beyond the usually covered frequency range by published standard drive cycles (up to 0.5 Hz). The higher frequency band is shown to be more efficiently covered by a Hybrid Energy Storage System (HESS) which in this paper is defined as combination of a high energy density battery, an Ultra-Capacitor (UC), an electrolytic capacitor, and a film capacitor. In this paper, the harmonic and dc currents and voltages are measured through two precision methods and then the results are used to discuss about overall HEV efficiency and durability. More importantly, the impact of the addition of high-band energy storage devices in reduction of power loss during transient events is disclosed through precision measurement based methodology.

Climate change and global warming are becoming important problems around the globe. To prevent these environmental problems, many countries try to reduce the emissions of greenhouse gases (GHG) and manage the consumption of energy. In Korea, Korea Electric Power Corporation (KEPCO) has introduced Smart Grid (SG) technologies to its branch office in 2014. This was the first demonstration of smart grid on a building called Smart Grid Station. This paper treats the achievements of the Smart Grid Station (SGS) by its early target in three aspects. The things are peak reduction, power consumption reduction and electricity fee saving. The authors analyzed the achievements by comparing the data of 2015 with the data of 2014. Through the evaluation, the authors studied the case, proved the advantages of SGS, and suggested the requirements to improve and the direction to go of the system.

In this paper, we propose a simple tool to help the energy management of a large buildings stock defining clusters of buildings with the same function, setting alert thresholds for each cluster, and easily recognizing outliers. The objective is to enable a building management system to be used for detection of abnormal energy use. First, we framed the issue of energy performance indicators, and how they feed into data visualization (Data Viz) tools for a large building stock, especially for university campuses. Both for Data Viz and clustering algorithm processes, we discussed two possible approaches to choose the right number of clusters and the identification of alert thresholds and outliers, after a brief presentation of the University of Turin's building stock case study. Different Data Viz tools have been studied to apply a specific clustering algorithm, the k-means one. An explorative analysis based on the general Multidimensional detective approach by Inselberg has been performed. Two multidimensional analysis tools, the Scatter Plot Matrix and the Parallel coordinates method have been used. Secondly, the k-means clustering algorithm has been applied on the same dataset in order to test the hypothesis made during the explorative analysis. Data Viz techniques developed in this study revealed to be very useful to explore quickly and simply a large buildings' stock, identifying the worst efficient buildings and clustering them according to their distinct functions.

Rural electrification in remote areas of developing countries has several challenges which hinders energy access to the population. For instance the extension of the national grid to provide electricity in these areas is largely not viable. The Kenyan government has put a target to achieve universal energy access by the year 2020. In order to realize this objective, focus is being shifted to establishing off-grid power stations in rural areas.Among rural areas to be electrified, Habaswein is a settlement in Kenya's North Eastern region without connection to the National Power Grid where Kenya Power installed a stand alone hybrid mini-grid.Based on field observations, power generation data analysis, evaluation of the potential energy resource and simulations, this research intends to evaluate the performance of the Habaswein mini-grid and optimize the existing hybrid generation system to enhance its reliability and reduce the operation costs.The result will be a suggestion of how Kenyan rural areas could be sustainably electrified by using renewable energy based off-grid power stations. It will contribute to bridge the research gap currently existing on that area, and it will be a vital tool to researchers, implementers and the policy makers in energy sector.

Technology is in the way to reach in its climax but the basic understanding of science in many phenomena is still awaited even though the nature witnesses it. Scientific research reveals strong analogy between photon and electron. When an atom deals neutral state, it levitates electron of outer ring from the back surface while placing the bit-energy at front surface. Gravitation behavior of that electron starts at the centre of relaxation point by including the force of side pole where the pulling force of nearby unfilled state of that atom from the front surface results into depict forcing energy shape like Gaussian distribution symbol with both ends turned called unit photon. The inertia is being involved at each stage of changing direction of that electron by introducing the disappearances of forces of two poles against the appearances of forces of two opposite poles during rest to motion and motion to rest in the first half-cycle. The same is the case in the second half-cycle of that electron during rest to motion and motion to rest but it is under different introduction of the disappearances of forces against appearances of forces. However, at stage of levitating or gravitating period of electron, only one force is being involved at one time where the opposite force is disappeared. The uninterrupted confined inter-state electron-dynamics of atom under the availability of several bits of bit-energy results into generate forcing energy shape like a wave. Two bits of bit-energy where shape of bit for first half-cycle is like integral symbol and second half-cycle is like opposite integral symbol which are being placed along the configuring trajectory of inter-state electron-dynamics during forward-direction cycle and two bits of bit-energy shape in opposite order are being placed along the trajectory of inter-state electron-dynamics during back-direction cycle. Generating forcing energy of unit photon in each cycle is pushing to the rear side by remaining connected till the electron is not restoring the state of rest. Silicon atom is considered as a model system under neutral state. Uninterrupted confined inter-state electron-dynamics result into generate forcing energy that can travel immeasurable length and unavailability of necessitating bit-energy at any interrupted stage result into generate an overt photon. Inter-state electron-dynamics for at least two cycles generate an overt photon –a photon length twice to unit photon. Under certain interaction of unit photon, it divides equally into two bits of bit-energy instead of dividing into tits and bits of heat. The mechanism of generating photon characteristic current by the electron of neutral state atom validates that atoms are four-dimensional discs at centre of dealing no force. An isolated electron is being grounded under directed forcing energy to impinge a neutral state atom where the gained instantaneous velocity under merged energy resulting into distort atom at that point. Matter changes the role of energy and force under various sorts of interactions. Here, heat energy and photon energy explore matter at atomic and electron levels, thus, devise basis of science to describe.

Property Assessed Clean Energy (PACE) programs finance energy efficiency and renewable energy improvements in residential and commercial properties with a special tax assessment added to property taxes. The paper surveys the literature and documents the quantitative estimates of environmental and economic benefits. The paper extends to discuss the securitization of PACE loans. The issuance of PACE green bonds frees up capacity for more PACE improvements. In addition, we summarize the concerns raised after the programs have been implemented. Those concerns include consumer protection, audit after program implementation, and lien-related risks for lenders. We highlight the challenges and discuss measures to continue to grow PACE financing. The success of PACE programs will contribute to mitigating climate change and to achieving the United Nations Sustainable Development Goals (SDGs).

Based on recent interest and on the importance of the ongoing climate change catastrophe, this article provides the basics of global carbon cycle modelling as required for the assessment of the degree of carbon neutrality of biomass energy, and its underlying dynamics. It is aimed at clari-fying the question “Are biomass fuels carbon neutral?”. The "Combined Energy and Biosphere Model" (CEBM) computes annual carbon flows including growth and decay of plants on 2.52.5° grid elements of the continents’ surface and offers detailed results on the changes of after implementation of large-scale biomass energy strategies world-wide. The main (and possibly unexpected) effect is the long-term depletion of the soil organic compartment after extraction of biomass fuels. When comparing CEBM model runs using (i) biomass energy sources and (ii) carbon-free energy sources (such as solar or wind), it becomes quantitatively clear already on the theoretical level (i.e., even without taking into account effi-ciency losses) that biomass is only “half as carbon neutral” as ideally assumed, to express a rule of thumb – mainly because of soil carbon depletion. Still, biomass energy will play an important role when fighting global warming, even if efforts to lower energy demand are preferable as a fundamental strategy.

In thermodynamic theory, free energy (i.e., available energy) is the concept facilitating the combined applications of the theory’s two fundamental laws, the first and the second laws of thermodynamics. The critical step was taken by Kelvin, then by Helmholtz and Gibbs— that in natural processes, free energy dissipates spontaneously. With the formulation of the second law of entropy growth, this may be referred to as the dissymmetry proposition manifested in the spontaneous increase of system/environment-entropy towards equilibrium. Because of Kelvin’s pre-entropy-law formulation of free energy, our concept of free energy is still defined, energy-centrally, as body’s internal energy or enthalpy, subtracted by energy that is not available within a framework on the premise of primacy of energy, in which free energy dissipates spontaneously and universally. This primacy of energy is called into question because the driving force to cause a system’s change is the purview of the second law. This paper makes a case for an engineering thermodynamics framework, instead, to be based on the premise of the primacy of dissymmetry over free energy. With Gibbsian thermodynamics undergirded with dissymmetry proposition and engineering thermodynamics with the dissymmetry premise, the two branches of thermodynamics are unified to become classical thermodynamics.

The author’s opinion is that the negative energy solutions of the Dirac equation mean that a particle can be of negative kinetic energy (NKE) besides positive kinetic energy (PKE). We think that NKE particles are dark ones and NKE matter is dark matter. In our previous works, the dark matter theory of the NKE version and the dark energy theory that matched dark matter theory were put forth. In this work, we investigate the topics related to the metamorphosis of objects between PKE and NKE. We first evaluate the collosions between a PKE and a NKE particles. A scenario of accelerating PKE particles is raised. We put forth the cosmic dark radiation background and gravity potential background. In the universe, negative energy is predominating. In the observable universe, substances constitute stable PKE systems. The total energy of every such system is negative. We propose a mechanism that NKE substances combine into stable PKE systems. Macroscopically, NKE objects can constitute stable PKE astrophysical systems by means of gravity between them. Microscopically, NKE particles can combine into stable PKE systems by means of attractive interactions between them, say, Coulomb attraction. Currently, people think that there are four ingrediants in the universe: photons \Omega_R0, matter \Omega_M0, dark matter \Omega_DM, and dark energy \Omega_\lambda0. We analyze the order of the appearance of the four ingredients and conclude that qualitatively, their proportions should be \Omega_\lambda0 > \Omega_DM > \Omega_M0 > \Omega_R0.

We live in the world that is completely entangled on energy and thus, Humankind can no longer do without it, power. With electricity being the main form of energy today, this has increased the complexity of our life today. In Uganda, electricity generation is mainly through hydropower which put the country in the bottleneck of over dependence on one source of energy. Yet, there are many energy systems out there that country can diversify its electricity generation. Therefore, the need to understand, the level of development and utilization of various energy systems has been the underlying question for this present study. Comprehensive literature survey was conducted from the electronic databases including ScienceDirect, Wiley, Sage, Scopus, Taylor & Francis, and Google Scholar. The publications in form of reports, conference papers, working papers, discussion papers, journal articles, book sections and textbooks were considered in this study. In total, 11 energy systems including human and animal energy, solid biomass (firewood), hydropower, wind, geothermal, solar, nuclear, peat, coal, petroleum, and non-solid biomass (methanol, hydrogen, ethanol, biodiesel, and biogas) are described. The current and the future development and utilization of these energy systems has been described. The challenges with their development and utilization were elaborated and the solution the challenges were presented. The hydropower with River Nile being the main river for large hydropower plant construction is the dominance energy system in Uganda. Nuclear energy will be the salvation for the country’s electric energy supply in the near future. Therefore, Uganda needs to bet big on nuclear energy.

Considering increasingly ambitious pledges by countries, pressure from society, investors, and clients further up the supply chain, the question for companies is not so much whether to take decarbonisation action, but what action and by when. However, determining an ideal mix of measures to apply ‘decarbonisation efficiency’ requires more than knowledge of technically feasible measures and how to combine them to achieve the most economic outcome: In this paper, the author describes seven aspects which heavily influence the composition of an ‘ideal mix’ that executive leadership needs to take a (strategic) position on. These aspects consider underlying motivations and span across (socio-)economic, technical, regulatory, strategic, corporate culture and environmental factors and further underline the necessity of clarity of definitions. How these decisions influence the determination of the decarbonisation-efficient ideal mix of measures, both in principle but also in terms of specific impact is further explored by providing examples. What choices are taken by German manufacturers in several of the aspects is disclosed by insights from about 850 responses to the ‘Energy Efficiency Index of German Industry’. Knowledge of the status quo, and clarity in definitions, objectives, time frames and scope are key.

Wave energy converter (WEC) arrays deployed in coastal regions may create physical disturbances potentially resulting in environmental stresses. Presently, limited information is available on the nature of these physical disturbance or the resultant effects. A quantitative Spatial Environmental Assessment Tool (SEAT) for evaluating potential effects of wave energy converter (WEC) arrays on nearshore hydrodynamics and sediment transport is presented for the central Oregon coast (USA) through coupled numerical model simulations of an array of WECs. Derived climatological wave conditions were used as inputs to the model to allow for the calculation of risk metrics associated with various hydrodynamic and sediment transport variables such as maximum shear stress, bottom velocity, and change in bed elevation. The risk maps provided simple, quantitative, and spatially-resolved means of evaluating physical changes in the vicinity of a hypothetical WEC array in response to varying wave conditions. Near-field risk of sediment mobility was determined to be moderate in the lee of the densely spaced array, where the potential for increased sediment deposition could result in benthic habitat alteration. Modifications to the nearshore sediment deposition and erosion patterns were observed near headlands and topographic features, which could have implications for littoral sediment transport. The results illustrate the benefits of a risk evaluation tool for facilitating coastal resource management at early market marine renewable energy sites.

While various studies have explored the integration of sustainability in the construction sector of Tanzania, particularly in areas like energy efficiency and green building practices, there remains a significant gap in understanding the specific barriers to the selection of sustainable building materials (SBMs) in residential projects. This research intends to bridge this gap by identifying and analyzing the critical barriers that hinder the effective selection of SBMs in Tanzania's residential building projects. By employing qualitative interviews with experts from regulatory bodies, public developers, and academic researchers, the study provides a comprehensive overview of the barriers. To ensure the collection of relevant and insightful data, the study involved the selection of participants based on specific criteria tailored to each category of experts. To be able to analyze qualitatively the data collected, this study employed Atlas.ti and MS Excel software. The findings revealed six categories of critical barriers affecting the selection of SBMs for residential building projects in Tanzania were identified and analyzed: (1) Regulatory and Policy Barriers (2) Financial Barriers (3) Knowledge and Awareness Barriers (4) Technical Barriers (5) Market and Supply Chain Issues (6) Cultural and Social Barriers. Moreover, the lack of awareness and limited knowledge issue were as equally importantly voiced as regulatory and policy barriers to affect the effective selection of sustainable materials in Tanzania. This study underscores the need for targeted policy interventions that address the lack of awareness, financial difficulties, and the absence of comprehensive regulatory frameworks to promote the selection of sustainable materials.

This narrative review synthesizes findings from empirical studies to explore the factors influencing the adoption of ChatGPT in higher education. The review highlights several critical determinants, both confirmed and debatable, of ChatGPT acceptance among students and educators. Previous studies have predominantly utilized theories such as the Technology Acceptance Model (TAM), the Unified Theory of Acceptance and Use of Technology (UTAUT), and the Diffusion of Innovations (DoI) theory. Confirmed factors include performance expectancy, effort expectancy, social influence, facilitating conditions, and trust, which significantly predict user attitudes and intentions toward adopting ChatGPT. Perceived usefulness and ease of use are core components influencing adoption positively. However, some factors have shown inconsistent impacts. While generally critical, effort expectancy and facilitating conditions vary based on context. Social influence, demographic characteristics (age, gender), extrinsic motivation, and technology readiness exhibit inconsistent effects, suggesting that intrinsic motivations may be more critical. Data collection primarily used online surveys with structured questionnaires, varying widely in sample sizes from small pilot studies to large-scale surveys and covering diverse academic disciplines. Practical implications suggest enhancing perceived usefulness and ease of use through training and technical support, building trust by addressing privacy concerns, and leveraging social influence to drive adoption. The review underscores the need to refine technology acceptance models to incorporate broader psychological and contextual factors, integrate intrinsic motivation theories, and adopt a systems thinking approach. Addressing limitations such as potential selection bias and the quality and scope of existing studies, future research can develop robust models and provide deeper insights into ChatGPT adoption dynamics in higher education, supporting its effective integration to enhance learning outcomes and foster educational innovation.

Heart failure is a major global health concern, especially in Ethiopia. Numerous studies have analyzed heart failure data to inform decision-making, but these often struggle with limitations to accurately capture death dynamics and account for within-cluster dependence and heterogeneity. Addressing these limitations, this study is then to incorporate the dependence and to analyze heart failure data to estimate survival time and identify risk factors affecting patient survival. The data, obtained from 497 patients at Jimma University Medical Center in Ethiopia, were collected between July 2015 and January 2019. Residence was considered as the clustering factor in the analysis. We employed the Bayesian accelerated failure time (AFT), and Bayesian AFT shared gamma frailty models, comparing their performance using the Deviance Information Criterion (DIC) and Watanabe-Akaike Information Criterion (WAIC). The Bayesian log-normal AFT shared gamma frailty model had the lowest DIC andWAIC, with well capturing cluster dependency that attributed to unobserved heterogeneity between patient residences. Unlike other methods that use Markov-Chain Monte-Carlo (MCMC), we applied the Integrated Nested Laplace Approximation (INLA) to reduce computational load. The study found that 39.44% of patients died, while 60.56% were censored, with a median survival time of 34 months. Another interesting finding of this study is by adding frailty into the Bayesian AFT models has boosted the performance in fitting the heart failure dataset. Significant factors reducing survival time included age, chronic kidney disease, heart failure history, diabetes, heart failure etiology, hypertension, anemia, smoking, and heart failure stage. The Bayesian model also showed lower standard errors for parameters compared to other methods, highlighting the importance of frailty models in accurately assessing survival time in heart failure patients.

Previous literature has linked working for pay while attending university with negative academic and health outcomes, yet working students are often resilient when experiencing such adverse circumstances. This makes it crucial to explore potential psychological mechanisms which transform adverse experiences into sources of motivation and persistence for working students. We explore one mechanism – social identification – and its different foci – identifying as a student, employee, working student, or as a student of one’s discipline of study – as potential predictors of important academic (academic self-efficacy, approaches to learning, and academic achievement) and social (status in society) outcomes in three cross-sectional studies. In Study 1, part-time working hours (but not identification processes) were associated with academic self-efficacy. In Study 2, discipline identification and part-time working hours were associated with using deep approaches to learning. In Study 3, student identification was associated with increased status in society. Overall, discipline identification may be solely linked to academic outcomes, yet student identification should be explored further as a potential enhancer of social and graduate outcomes. We discuss additional mechanisms which can help to transform working students’ experiences through their social identities and suggest boundary conditions which can affect the link between these identities and important outcomes.

The study aims at evaluating the demand of forest bathing in the Northern Italy’s regions underlining the willingness to pay and the potential tourists’ habits and flows on attending alpine contexts. Through the submission of a questionnaire, the sample’s answers have been analyzed employing a stratified sampling methodology considering three different macro areas (Northwest regions, Northeast regions, and Friuli Venezia Giulia region). After analyzing the sample attitudes, the research approached the estimation section by calculating the flow as the number of potential forest bathing hikes per year and the willingness to pay trough the Contingent Valuation Method. The main results indicate that Forest Bathing activity in Northern Italy have a considerable monetary value and it is generally compared with positive feelings, particularly concerning well-being, and fascination factors.

Introduction: Rural Americans face significant health disparities due to limited access to healthcare services. Telehealth has emerged as a promising solution to mitigate these disparities by facilitating remote access to medical care. This paper comprehensively reviews the advantages, challenges, and implementation strategies of telehealth in rural areas.Method: A narrative review methodology was employed to synthesize existing literature and case studies on telehealth in rural settings. Databases such as PubMed, Google Scholar, and JSTOR were searched for relevant studies published in the last three decades. Keywords such as "telehealth," "rural health," and "healthcare disparities" guided the search process. The review focused on studies assessing the impact of telehealth on healthcare access, cost-effectiveness, and quality of care in rural areas.Results: The review findings indicate that telehealth significantly enhances healthcare access by reducing travel distances, increasing availability of specialist consultations, and promoting patient engagement. It improves chronic disease management and patient satisfaction by enabling convenient access to healthcare services at home. Despite initial setup costs and challenges such as broadband access and regulatory issues, telehealth demonstrates long-term cost savings through reduced travel expenses and improved healthcare efficiency. Quality of care is enhanced through improved communication between healthcare providers and patients, leading to better treatment adherence and health outcomes.Conclusion: Telehealth represents a transformative approach to address healthcare disparities in rural areas. It offers a cost-effective solution to improve access to healthcare services, enhance patient outcomes, and reduce healthcare costs in the long run. However, successful implementation requires addressing infrastructure challenges, refining reimbursement policies, and ensuring regulatory support. Future efforts should focus on expanding broadband infrastructure, refining policy frameworks, and conducting further research to optimize telehealth's impact on rural healthcare delivery.

Computational neuroscience has undergone a significant transformation in recent years, driven by the exponential growth of neural data and advancements in data science and machine learning. While traditional theoretical models remain valuable, there is a growing emphasis on integrating data-driven approaches to develop more accurate, biologically plausible, and predictive models of neural function. This shift has led to a new equilibrium in the field, where data-driven model development, machine learning techniques, and hybrid approaches that combine data and theory are increasingly prevalent. In this article, we discuss the evolving landscape of computational neuroscience, highlighting the importance of data-driven methods and the emergence of a more integrative approach that leverages both data and theory to unlock the mysteries of the brain. We also explore the implications of this shift for future research and clinical applications, emphasizing the potential for data-driven computational neuroscience to revolutionize our understanding of neural function and pave the way for new treatments for neurological disorders.

This research presents a novel algorithmic implementation to improve the analysis of visually controlled interception and accompanying motor action through the computational application of harmonic ratios and stimulation invariants. Unlike traditional models that focus mainly on psychological aspects, our approach integrates the relevant constructs into a practical mathematical framework. This allows for dynamic prediction of interception points with improved accuracy and real-time perception-action capabilities, essential for applications in neurorehabilitation and virtual reality. Our methodology uses stimulation invariants as key parameters within a mathematical model to quantitatively predict and improve interception outcomes. The results demonstrate the superior performance of our algorithms over conventional methods, confirming their potential for ad-vancing robotic vision systems and adaptive virtual environments. By translating complex theo-ries of visual perception into algorithmic solutions, this study provides innovative ways to im-prove motion perception and interactive systems. This study aims to articulate the complex inter-play of geometry, perception, and technology in understanding and utilizing cross-ratios at infin-ity, emphasizing their practical applications in virtual and augmented reality settings.

Developing countries, including Small Island Developing States (SIDS) and Least Developed Countries (LDCs), are exceptionally vulnerable to climate change due to their distinct geographical and environmental characteristics. The impacts of climate change extend across their ecosystems, water resources, and vital economic sectors, such as food systems, health, education, and energy. Escalating sea levels and heightened salinity levels imperil freshwater reserves, while warmer ocean temperatures and acidification disrupt water demand, tourism, health services, and fisheries. Furthermore, developing countries bear the brunt of water shortages, flooding, and deteriorating water quality. Alarmingly, nearly two-thirds of the global population experience severe water scarcity for at least one month annually, with the majority residing in developing countries. By 2025, half of the world's population could inhabit areas grappling with water scarcity, predominantly concentrated in developing nations. In this context, innovative adaptation strategies, notably transformative wastewater projects, are imperative for fostering sustainability and resilience in these regions. However, significant barriers impede progress, creating a stark disparity between current financing capabilities and the imperative to fund water security initiatives. Compounding these challenges, developing countries find themselves ensnared in a burgeoning debt crisis, marked by escalating interest rates and inflation, which threatens to impede developmental progress and curtail investments in adaptation and mitigation endeavors. Consequently, there arises a critical necessity to harness innovative financial mechanisms to transform these debts into assets that facilitate climate action. This paper meticulously explores the potential of debt-for-climate swaps as a catalyst for advancing transformative wastewater projects, with a focused lens on their strategic deployment to underpin critical initiatives. Through rigorous examination of case studies and empirical evidence, the paper elucidates how debt-for-climate swaps can effectively bolster sustainable wastewater management systems in developing countries. Furthermore, it delineates best practices for leveraging these mechanisms to fortify environmental sustainability and resilience. Additionally, the paper delineates the roles and responsibilities of key stakeholders, including governments, policymakers, the private sector, communities, and climate financial institutions. By amalgamating theoretical insights with tangible examples, this paper furnishes a comprehensive framework for harnessing debt-for-climate swaps to enhance water security and resilience in developing countries. It endeavors to furnish actionable strategies for policymakers, practitioners, and stakeholders to navigate the complex terrain of climate change and engender sustainable development.

Background. Escherichia coli commonly causes catheter-related bloodstream infection (C-RBSI) in specific populations. The differential time to positivity (DTTP) technique is the recommended conservative procedure for diagnosing C-RBSIs. Methods. We conducted a retrospective study of episodes in which E. coli was isolated from catheter lumens obtained using the DTTP technique. We analysed microbiological and clinical data based on the DTTP technique as either catheter colonization, C-RBSI, or non-C-RBSI. Results. We included 89 catheter blood cultures classified as follows: catheter colonization, 33.7%; C-RSBI, 9.0%; and non-C-RBSI, 57,3%. Catheter withdrawal was 15.7% without positive catheter-tip cultures. We found no statistically significant differences in catheter type, antibiotic treatment, or clinical outcome among groups, except for the frequency of catheter lock therapy or in the frequency of successful treatment. Mortality was associated with C-RBSI in only 1 patient. Conclusion. E. coli bacteremia diagnosed by the DTTP technique was non-catheter related in most patients. As the majority of the catheters were retained, E. coli bacteremia could not be microbiologically confirmed or ruled out as catheter related by catheter-tip culture. Future studies are needed to assess the profitability of the DTTP technique for diagnosing E. coli C-RBSIs..

This retrospective study examines 248 test-bolus examinations preceding contrast-enhanced magnetic resonance angiography (CE-MRA) to extract clinically relevant data for critical limb ischemia (CLI) management. Methods involved a retrospective review of test-bolus exams, analysing 60 graphs for time-to-peak (TTP), full-width half-maximum (FWHM) time, and time to continual rise in signal intensity. These values were correlated with heart function parameters (ejection fraction, ASA-Classification, Lee-Index, and MET-Score). Results indicate a mean TTP of 31.2 ± 7.3s, showing a correlation between ejection fraction and ASA classification. Patients with atrial fibrillation exhibited prolonged TTP compared to those without. Despite population heterogeneity, findings facilitate risk stratification for limb-saving interventions in CLI. TTP emerges as a potential clinical cardiovascular parameter and a risk factor for vascular interventions. Given the variation in injection protocols across centres, this study underscores the importance of precise bolus arrival time documentation for future multicentre studies.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Silicon Photomultipliers find applications across various fields. One potential Silicon Photomultiplier application domain is neutrino telescopes, where they may enhance the angular resolution. However, the elevated dark count rate associated with Silicon Photomultipliers represents a significant challenge to their widespread utilization. To address this issue, it is proposed to use Silicon Photomultipliers and Photomultiplier Tubes together. The Photomultiplier Tubes signals would serve as a trigger to mitigate the dark count rate, thereby preventing undue saturation of the available bandwidth. This paper presents an investigation into a fast and resource-efficient method for filtering Silicon Photomultiplier dark count rate. A low-resource and fast coincident filter has been developed, which removes the Silicon Photomultiplier dark count rate by using as trigger the Photomultiplier Tube input signals. The architecture of the coincidence filter, together with the first results obtained, which validate the effectiveness of this method are presented.

There are two generic approaches to curing any medical condition. The first treats every patient for all of the known possible causes that contribute to pathogenesis; the second individualizes potentially curative therapy by identifying in each separate patient only those components of pathogenesis that are actually operative, and treating those. This article adopts the second approach for formulating a cure of Alzheimer’s dementia (AD). Components of AD’s pathogenesis are, in alphabetical order: circadian rhythm disturbances, depression, diabetes and insulin resistance, dyslipidemia, hypertension, inflammation, metabolic syndrome, mitochondrial dysfunction, nutritional deficiencies, TGF-β deficiency, underweight, vascular abnormalities, and Wnt/β-catenin deficiency. For each component, data are described that show the degree by which its prevalence is more in the patients with mild cognitive impairment (MCI) who did not revert to having normal cognition than in those who did, because the former group is the pool of patients from among which future AD may develop. Addressing only those components that are present in a particular individual, is potentially a curative strategy. Published data indicate that curative therapy requires that the number of such components to address should be ≥3. Although structural brain changes cannot be directly addressed, the impaired neural tracts result from many of the reversible causal elements, so correcting them will benefit those tract

It is unavoidable that the characteristics of the robot system alter inexactly or cannot be correctly determined during movement and are impacted by external disturbances. There are many adaptive control methods, such as sliding control or neural control, to improve the quality of trajectory tracking for robot motion systems. Still, those methods require a large amount of computation related to solving the problem of constrained nonlinear optimization problem. The article presents some techniques for determining an intelligent controller's online learning function parameters, including two circuits: the inner circuit is a state feedback linearized controller, and the outer course is an Interactive learning controller and does not use the robot's mathematical mode with function parameters online optimal learning and intelligent online learning closely following the joint model to stabilize the robot system. Finally, the 2-DOF planar robot simulation is performed on Matlab software R2022b. The findings indicate that outstanding tracking performance is achievable.

Inverse optimal control is a method for recovering the cost function used in an optimal control problem in expert demonstrations. Most studies on inverse optimal control have focused on building the unknown cost function through the linear combination of given features with unknown cost weights, which are generally considered to be constant. However, in many real-world applications, the cost weights may vary over time. In this study, we propose an adaptive online inverse optimal control approach based on a neural-network approximation to address the challenge of recovering time-varying cost weights. We conduct a well-posedness analysis of the problem and suggest a condition for the adaptive goal, under which the weights of the neural network generated to achieve this adaptive goal are unique to the corresponding inverse optimal control problem. Furthermore, we propose an updating law for the weights of the neural network to ensure the stability of the convergence of the solutions. Finally, simulation results for an example linear system are presented to demonstrate the effectiveness of the proposed strategy. The proposed method is applicable to a wide range of problems requiring real-time inverse optimal control calculations

People are drawn to woodcut-style designs due to their striking visual impact and strong contrast. However, traditional woodcut prints and previous computer-aided methods have not addressed the issues of dwindling design inspiration, lengthy production times, and complex adjustment procedures. We propose a novel network framework, the Woodcut-style Design Assistant Network (WDANet), to tackle these challenges. Notably, our research is the first to utilize diffusion models to streamline the woodcut-style design process. We've curated the Woodcut-62 dataset, featuring works from 62 renowned historical artists, to train WDANet in absorbing and learning the aesthetic nuances of woodcut prints, offering users a wealth of design references. Based on a noise reduction network, our dual cross-attention mechanism effectively integrates text and woodcut-style image features. This allows users to input or slightly modify a text description to quickly generate accurate, high-quality woodcut-style designs, saving time and offering flexibility. As confirmed by user studies, quantitative and qualitative analyses show that WDANet outperforms the current state-of-the-art in generating woodcut-style images and proves its value as a design aid.

Natural gas plays a significant role in Tunisia's energy mix. Tunisia imports 66% of natural gas (NG) from Algeria (ANG), and the rest is provided by local gas fields mainly Miskar gas (MNG). To counteract this deficit, the Power-to-Gas approach emerges as a promising solution, given Tunisia's abundant renewable energy resources. By blending green hydrogen into the NG network, it is possible to (i) address the current energy crisis, (ii) lower the carbon intensity of the gas grid, and (iii) encourage sector coupling through the use of various renewable energy sources. This study presents an overview of various interchangeability indicators and investigates accordingly the allowable ratios for hydrogen blending with two types of natural gas distributed in Tunisia (ANG and MNG). It also explores the impact of hydrogen injection on the energy content variation and various combustion parameters. The results confirm that both ANG and MNG can withstand a maximum hydrogen blend of up to 20%. The article concludes with recommendations for further experimental testing of the findings and emphasizes the need to look into infrastructure and safety requirements with regards to the Natural gas network in Tunisia. This research serves as a critical step towards harnessing the potential of green hydrogen in Tunisia.

This paper delves into the essential role of local communities in mitigating climate change in the post-pandemic landscape, with a specific focus on Barangay Acmac, Iligan City, Philippines. Employing a qualitative research approach, the study integrates in-depth literature reviews, informal interviews with participants (B-Part 1 to B-Part 20), meticulous observations, and thematic analysis. The research has uncovered crucial insights, including variations in community climate change awareness that emphasize the necessity of comprehensive education and awareness campaigns. It highlights the significance of community-driven initiatives, adaptation, and resilience as key elements in addressing climate change. Collaborative efforts between local government officials and the community are showcased as effective instruments of climate change mitigation, yet challenges persist, including addressing the perceived powerlessness of some community members. The methodology, participants, and theoretical framework offer a robust foundation for exploring community responses to climate change. Drawing from a diverse theoretical framework, this study presents a comprehensive understanding of the climate change and pandemic intersection. The findings firmly establish that local communities are pivotal players in the global endeavor to mitigate climate change, underscoring the need for collective action, extensive education, and shared responsibility. The post-pandemic era presents a unique opportunity for local communities, policymakers, barangay officials, and residents to champion climate education, foster community-driven initiatives, and empower individuals to enact change at the grassroots level. The collaborative spirit observed in Barangay Acmac in 2022 serves as a model for communities worldwide, offering a blueprint for addressing similar challenges. Overall, this paper concludes with a resounding call to action, advocating for the recognition of local communities as the driving force in climate change mitigation, stressing that the power to combat climate change resides within these communities. The time for action is now, and local communities are the catalysts of this essential mission.

The aim of this article is to review hydrogen combustion applications within the energy transition framework. Hydrogen blends are also included, from the well known hydrogen enriched natural gas (HENG) to the hydrogen and ammonia blends whose chemical kinetics is still not clearly defined. Hydrogen and hydrogen blends combustion characteristics will be firstly summarized, in terms of standard properties like the laminar flame speed and the adiabatic flame temperature, but also evidencing the critical role of hydrogen preferential diffusion in burning rate enhancement and the drastic reduction in radiative emission with respect to natural gas flames. Then, combustion applications in both thermo-electric power generation (based on internal combustion engines, i.e., gas turbines and piston engines) and hard-to-abate industry (requiring high temperature kilns and furnaces) sectors will be considered, highlighting the main issues due to hydrogen addition related to safety, pollutant emissions, and potentially negative effects on industrial products (e.g., glass, cement and ceramic).

This study aims to investigate how the adoption of an online to offline (O2O) transition strategy impacts the sales volume of Kampoeng Merdeka Clothing. The O2O strategy includes various components, such as establishing O2O platforms, delivering personalized services, ensuring secure transactions, and engaging in offline business activities. The research employs a quantitative approach, focusing on consumers who have made clothing purchases from Kampoeng Merdeka Clothing in Macassar. The sample size comprises 83 respondents, deliberately selected using the Slovin approach. The data analysis and methodology involve the application of Partial Least Squares (PLS) structural equation modeling to assess both the external and internal models. The findings of this study emphasize the significant and positive influence of the variables "Build O2O Network Platform," "Provide Personalized Experience," "Safeguard Transactions Security," and "Offline Business" on driving the sales growth of Kampoeng Merdeka Clothing. These results indicate that the O2O transition strategy has a substantial impact on the brand's sales performance, with the establishment of O2O platforms and personalized services playing crucial roles. Additionally, ensuring secure transactions and engaging in offline business activities further contribute to the overall success of Kampoeng Merdeka Clothing in the market. This research sheds light on the effectiveness of the O2O approach in boosting sales for clothing brands and underscores the importance of integrating online and offline elements to maximize business outcomes.

Higher salt (sodium) intake has been associated with a higher blood pressure (BP). The association degree may be influenced by factors such as age, origin and dietary components. This study aimed to evaluate the 24-hours urinary sodium (Na) and potassium (K) excretion in normotensive and hypertensive Dominicans adults and estimate their salt intake. 163 volunteers (18-45, 46-80 years) participated in a cross-sectional study. 24-hours Na and K urinary excretion were measured using an ion selective electrode technique. Na and K urinary excretion (99.4±46.5 and 35.0±17.5 mmol/24h) did not correlated with BP, except in the normotensive group in which K correlated with SBP (0.249, p=0.019). Na and K excretion were similar for normo- and hypertensive subjects. Na-to-K molar ratio (3.1±1.3) was higher in younger subjects (p=0.040). Na-to-K ratio was associated with DBP in the total group (r=0.153, p=0.052), in the hypertensive group (r=0.395, p<0.001) and in the older group with SBP (0.350, p=0.002) and DBP (0.373, p<0.001). In the older group, Na-to-K ratio and DBP correlated after controlling for subjects with hypertension controlled by treatment (r=0.236, p=0.041). The Na-to-K ratio correlated, when salt intake was over 5g/d (52.2%), with SBP (rho=0.219, p=0.044) and DBP (rho=0.259, p=0.017). Determinants of BP were age-dependent and in younger subjects were: sex (SBP, beta: 14.02±2.87, p<0.001) and body mass index (BMI) (beta:-12.07±3.72, p=0.001, beta:9.44±2.87, p=0.001, for SBP and DBP, respectively) and, in the olders, the Na-to-K ratio, for SBP (beta:6.7±2.4, p=0.005) and DBP (beta:3.8±1.1, p<0.001). The mean Na and salt intakes (2.3 and 5.8 g/d) were slightly higher and K intake lower (1.4 g/d) than WHO recommendations.

Abstract: Systemic inflammatory response syndrome (SIRS) is a clinical diagnosis based on abnormalities in patients' vital signs and white blood cell count. Neutrophil-lymphocyte ratio (NLR) is used as an easily accessible parameter to assess the patient's inflammatory status and stress. There are some studies showing that NLR affected by the inflammatory response is a criterion to support the diagnosis of SIRS. In this study, it was aimed to compare the interrelation between SIRS (+) and SIRS (-) groups in patients with high positive feline coronavirus (FCoV) in the light of NLR. Based on the anamneses, physical examination findings, laboratory findings, enzyme immunoassay antibody test kit titer were included in the sick groups. These patients were further categorized based on the presence of SIRS symptoms, vital signs and laboratory findings. The NLR as diagnostic marker demonstrated to differ between high antibody titer FCoV positive and healthy cats. However the diagnostic significance of NLR remains questionable between the high antibody titer FCoV positive cats with SIRS (+) and SIRS (-). As a result of our study NLR can be used as a blood parameter like albumin/globulin ratio and elevated total bilirubin in cats with high FCoV antibody titer and high probability of developing FIP.

The basic constitutional freedoms and rights of a person and citizen are in principle unlimited: the full scope of their exercise is the rule, and the restriction determined by law can only be an exception based on explicit constitutional authority and the legitimate aim of the restriction determined by the Constitution. That being so, the restrictions - in addition to being based on constitutional authority and pursuing constitutional objectives - should be commensurate with the needs to achieve these objectives. This means that restrictive legal rules must be suitable for achieving the legitimate aim pursued, must not be stricter than necessary and must be balanced between the constitutionally guaranteed subjective right of the individual and the interests of society. In this scholar paper, the authors point out the economic and legal consequences of the violation of individual privacy and data protection rights caused by the public disclosure of personal data of people who, at a certain time, were obliged to self-isolate due to suspicion of Covid-19 virus infection.

One of the models that could be used to understand the adoption of vaccine uptake is the Health Belief Model (HBM). The aim of this study is to assess the role of HBM constructs and perceived health status (PHS) on vaccination status of individuals and to understand the role of socio-demographic variables on HBM scoring. A comparative cross-sectional telephone survey was conducted among 1,325 vaccinated (60.0%) and non-vaccinated (40.0%) vaccinated individuals aged 40 years and above in July 2021 in Punjab province, Pakistan. A higher level of education was the strongest predictor of positive HBM. All constructs of HBM, PHS and cues-to-action were significant predictors of COVID-19 vaccination uptake with perceived benefits as the strongest predictor. In order to expand the vaccination coverage, doubled pronged interventions utilizing both ICT and human resources should be designed that address each barrier perceived by individuals and understandably communicate the benefits of COVID-19 vaccine to the broader population.

The effects of transcranial magnetic stimulations (TMS) show that the human brain is impacted by some magnetic fields (EMFs). Moreover, after a delay, it produces potentials that reveal a subsequent processing of this impact. The human brain might also be sensitive to very weak magnetic fields of extremely low frequencies (vwEMFelf). Namely, to the vwEMelf produced by the brain of other persons when they process visual stimuli. In effect, two studies report that the event-related brain potentials (ERPs) that are evoked by presenting a picture to a participant can be modulated by simultaneously presenting a picture to a partner. To confirm it here, we followed most of the methods of these studies. We recorded the ERPs evoked by presenting, at each trial, the photograph of a face. Simultaneously and, most importantly, privately, we presented a partner with the same or with a different face photograph. ERPs of participants were found to depend on that sameness (p0.001), unbeknownst to them. These joint processing effects (JPEs), confirm a sensitivity of the human brain to the vwEMFelf produced by other brains.

A major challenge in the clinical management of patients with mesial temporal lobe epilepsy (MTLE) is identifying those who do not respond to antiseizure medication (ASM), allowing for the timely pursuit of alternative treatments, such as epilepsy surgery. Here, we investigated changes in plasma metabolites as biomarkers of pharmacoresistance in patients with MTLE. Furthermore, we used the metabolomics data to gain insights into the mechanisms underlying MTLE and response to ASM. We performed an untargeted metabolomic method using magnetic resonance spectroscopy and multi- and univariate statistical analyses to compare data obtained from plasma samples of 28 patients with MTLE compared to 28 controls. The patients were further divided according to response to ASM: 20 patients were refractory to treatment, and eight were responsive to ASM. We only included patients using carbamazepine in combination with clobazam. We compared the group of patients with controls and found that the profiles of glucose (p = 0.01), saturated lipids (p = 0.0002), isoleucine (p = 0.0001), β-hydroxybutyrate (p = 0.0003), and proline (p = 0.02) were different in patients compared to controls (p &lt; 0.05). In addition, lipoproteins (p = 0.05), lactate (p = 0.05), glucose (p = 0.05), unsaturated lipids (p = 0.05), isoleucine (p = 0.05), and proline (p = 0.05), could discriminate between the two groups of patients classified according to response to ASM. The identified metabolites were linked to different biological pathways related to cell energy metabolism, and pathways linked to inflammatory processes and the modulation of neurotransmitter release and activity in MTLE. In contrast, we found that pyruvate metabolism may be linked to resistance to ASM. In conclusion, in addition to insights into the mechanisms underlying MTLE and the response to treatment with ASM, our results suggest that plasma metabolites may be used as biomarkers of disease and response to ASM in patients with MTLE. These findings warrant further studies exploring the clinical use of metabolites to assist in decision-making when treating patients with MTLE.

We describe a method for protein quantification and for mRNA quantification in small sample quantities of human induced pluripotent stem-cell-derived-cardiomyocytes (hiPSC-CMs). Demonstrated here is how the capillary-based protein detection system Wes^TM by ProteinSimple and the Power SYBR^TM Green Cells-to-CT^TM Kit by Invitrogen can be applied to individual samples in a 96-well microplate format and thus made compatible with high-throughput (HT) cardiomyocyte assays. As an example of the usage, we illustrate that Cx43 protein and GJA1 mRNA levels in hiPSC-CMs are enhanced when the optogenetic actuator, channelrodopsin-2 (ChR2), is genetically expressed in them. Instructions are presented for cell culture and lysate preparations from hiPSC-CMs, along with optimized parameter settings and experimental protocol steps. Strategies to optimize primary antibody concentrations as well as ways for signal normalization are discussed, i.e. antibody multiplexing and total protein assay. The sensitivity of both the Wes and Cells-to-CT kit enables protein and mRNA quantification in a HT format, which is important when dealing with precious small samples. In addition to being able to handle small cardiomyocyte samples, these streamlined and semi-automated processes enable quick mechanistic analysis.

Plants characterized by a soft or weak steam, such as climbing plants, need to find a potential support (e.g., wooden trunk) to reach greater light exposure. Since Darwin’s research on climbing plants, several studies on their searching and attachment behaviors have demonstrated their unique ability to process different support features to modulate their movements accordingly. Nevertheless, the strategies underlying this ability are yet to be uncovered. The present research tries to fill this gap by investigating how the interaction between above- (i.e., stem, tendril, …) and belowground (i.e., the root system) plant organs influence the kinematics of the approach-to-grasp movement. With three-dimensional (3D) kinematical analysis, we characterized the movement of pea plants (Pisum sativum L.) towards a support with different thicknesses above and belowground (i.e., thin below, thick aboveground, or the opposite). As a control condition, the plants were presented to supports with the same thickness below- and aboveground (i.e., either entirely thin or thick). The results suggest an integration between the information from below- and aboveground for driving the reach-to-grasp behavior of the aerial plant organs. Information about the support conveyed by the root system seems particularly important to fulfil the end-goal of the movement.

Both academic literature and global organizations have emphasized the need for responsible water consumption, as stated in the Sustainable Development Goal 12. However, individuals’ water-saving behaviors in their current state are not enough. This situation entails a resistance to change (RC) in consumer habits and a lack of perceived risk of scarcity. The novelty of this study lies in examining the influence of RC (through its emotional, cognitive, and confidence components) and perceived risk on water-saving intention. Interviews (n = 384) were conducted in the southeast Mediterranean area of Spain by interviewers using a paper-and-pencil questionnaire. The results of the structural equation modeling show that the perceived risk and the components of cognitive rigidity and negative emotions exert a direct influence on water-saving habits and an indirect influence on water-saving intention. None of the components of RC directly influence intention, and a lack of confidence in the outcomes of water saving does not influence water-saving habits or water-saving intention. In addition to the results obtained, the novelty of the work lies in the idea that in order to influence the perception of the risk of water scarcity through awareness campaigns, it is better to use an emotional message rather than showing facts or information, because this does not drive water saving behavior.

High-performance motor drives that operate in harsh conditions require an accurate and robust angular position measurement to correctly estimate the speed and reduce the torque ripple produced by angular estimation error. For that reason, a resolver is used in motor drives as a position sensor due to its robustness. A resolver-to-digital converter (RDC) is an observer used to get the angular position from the resolver signals. Most RDCs are based on angle tracking observers (ATOs). On the other hand, generalized predictive control (GPC) has become a powerful tool in developing controllers and observers for industrial applications. However, no GPC-based RDC with zero steady-state error during constant speed operation was proposed. This paper proposes an RDC based on a second-order difference GPC (SOD-GPC). In SOD-GPC, the second-order difference operator is applied to design a GPC model with two embedded integrators. Thus, the SOD-GPC is used to design a type-II ATO whose steady-state angle estimation error tends to zero during constant speed operation. Simulation and experimental results prove that the proposed RDC system has better performance than other literature approaches.

The primary purpose of the study was the determination of the spatial day-to-day variability of extreme temperatures in Poland and the dependency of large temperature changes on atmospheric circulation in accordance with the Grosswetterlagen (GWL) classification. The goal was implemented based on data from 1966 to 2015, made available by the Institute of Meteorology and Water Management – National Research Institute. Day-to-day changes in maximum and minimum temperatures were designated with a rate of ≥ 6 °C (large) and with a rate of ≥ 12 °C (very large) and their spatial distribution was presented. Finally, the analysis of the dependency of considerable temperature changes on atmospheric circulation in accordance with the Grosswetterlagen (GWL) classification was conducted. The obtained results showed that in Poland in the period 1966-2015 the number of large changes in both Tmax and Tmin slightly increased, although the fluctuations show spatial variability. Large changes in Tmax occur more frequently in spring, and in Tmin in winter. Large changes in Tmax and Tmin are mainly recorded during cyclonic circulation, however, the anticyclonic circulation types favour especially large decreases in Tmin.

Over the past decade, wireless communication technologies have developed significantly for intelligent applications in road transport. This paper provides an overview of telecommunications-based intelligent transport systems with a focus on ensuring system safety and resilience. In vehicle-to-everything, these problems are extremely acute due to the specifics of the operation of transport networks, which requires the use of special protection mechanisms. In this regard, it was decided to use blockchain as a system platform to support the needs of transport systems for secure information exchange. This paper describes the technological aspects of implementing blockchain technology in vehicle-to-network; the features of such technology are presented, as well as the features of their interaction.

The tobacco epidemic is one of the leading public health threats the world has ever faced and public health policy that seeks to limit the problem may not only have to target the price of tobacco but also the initiation stage in a smoker’s life – the adolescent stage. This research contributes to the health economics literature by using a Bayesian hierarchical logistic model, estimated using Hamiltonian Monte Carlo (HMC) methods to empirically identify what drives the intentions to quit smoking among adolescent smokers in Zambia. Results suggest that among the junior secondary school-going adolescent smokers in Zambia, about 63% have plans to quit smoking. We find socio-demographic characteristics and several tobacco-smoking-related factors as the main drivers of adolescent smokers’ plans to quit smoking. Most importantly, we provide insights that could be useful to help adolescent smokers realize their quitting plans.

Background: Telemedicine (interconsultation between primary and hospital care teams) has been operating in the counties of Central Catalonia Bages, Moianès and Berguedà since 2011 in the specialties of teledermatology, teleulcers, teleeyelids and teleaudiometries. For the period until the end of 2019, a total of 52,198 visits have been recorded. Objective: To analyse the differential costs between telemedicine and usual care in a semi-urban environment. Methodology: A cost-minimization evaluation, including direct and indirect costs from a societal perspective, distinguishing healthcare and user’s costs, within a three-month period. Results: Telemedicine saved € 780,397 over the period analysed. A differential cost favourable to telemedicine of about € 15/visit has been observed, the patient being the largest beneficiary of this saving (by 85%) in terms of shorter waiting times and travel costs. From the healthcare system perspective, moving the time spent in a hospital care consultation to primary care is efficient in terms of the total time devoted per patient. In social terms and in this context, telemedicine is more efficient than usual care. Conclusion: Users’ saving of time in terms of consultation and travel is the main driver of interconsultation between primary and hospital care savings in a semi-urban context. The telemedicine service is also economically favourable for the healthcare system, enabling it to provide a more agile service, which also benefits the healthcare professionals.

This study used double-bounded dichotomous-choice to estimate and analyze the factors affecting households’ willingness to pay (WTP) for water quality improvement. This study notes that households with higher income, living near polluted water source, using tap water instead of natural water, who are handicraft producers, and who have more members are willing to pay more. However, households who rarely hear about environmental pollution issues and who are offered a higher bid are more likely to refuse to pay. Solutions to improve water quality are suggested such as to raise people's awareness through communication channels and social organizations; to increase income associated with environmental protection policies; to construct wastewater treatment plants; to encourage the relocation of production establishments to industrial parks and industrial complexes; to put regulations on collection, payment and sanctions in case of not declaring and paying fees into village conventions; to promulgate circulars, and bylaws to concretize and simplify regulations and policies of the Government, Ministry of Natural Resources and Environment.

Purpose: Localization and mapping with LiDAR data is a fundamental building block for autonomous vehicles. Though LiDAR point clouds can often encode the scene depth more accurate and steadier compared with visual information, laser-based Simultaneous Localization And Mapping (SLAM) remains challengeable as the data is usually sparse, density variable and less discriminative. The purpose of this paper is to propose an accurate and reliable laser-based SLAM solution. Design/methodology/approach: The method starts with constructing voxel grids based on the 3D input point cloud. These voxels are then classified into three types to indicate different physical objects according to the spatial distribution of the points contained in each voxel. A global environment model with Partition of Unity (POU) implicit surface is maintained along the process and located voxels are merged into it from stage to stage, through scan-to-model matching implemented by Levenberg-Marquardt method. Findings: We find a laser-based SLAM method. The method uses POU implicit surface representation to build the model and is evaluated on the KITTI odometry benchmark without loop closure. Experimental results indicate that the method achieves accuracy comparable to the state-of-the-art methods. Originality/value: We propose a novel, low-drift SLAM method, which falls into a scan-to-model matching paradigm, operates on point clouds obtained from Velodyne HDL64. The method is of value to researchers developing SLAM systems for autonomous vehicles.