To reduce the cost of small wind turbines, a prototype of a butterfly wind turbine (6.92 m in diameter), a small vertical-axis type, was developed with many parts made of extruded aluminum suitable for mass production. An over-speed control system with movable arms that operated using centrifugal and aerodynamic forces was installed for further cost reduction. Introducing this mechanism eliminates the need for large active brakes and expands the operating wind speed range of the wind turbine. However, although the mechanism involving the use of only bearings is simple, the violent movement of the movable arms can be a challenge. To address this in the present study, dampers were introduced on the movable arm rotation axes to improve the movement of the movable arms. To predict the behavior of a movable arm and the performance of the wind turbine with the mechanism, a simulation method was developed based on the blade element momentum theory and the equation of motion of the movable arm system. Comparison of experiments and predictions with and without dampers demonstrated qualitative agreement. In the case with dampers, measurements confirmed the predicted increase in the rotor rotational speed when the shorter ailerons installed perpendicularly to the movable arms were used to achieve the inclination. The movable arm system with dampers is expected to be a useful device for vertical-axis wind turbines that are difficult to control.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Experimental investigations were conducted to uncover the impact of cavitation control - through the use of riblets (mesoscale surface structuring) - on cavitating flows around a circular cylinder. First, the dynamics of cavitation in the flow behind a finite cylinder (without riblets) was unveiled by visualizing the cavitation clouds and measuring the lift force fluctuations acting on the cylinder. Second, as a significant step forward, a comprehensive explanation was provided for the mechanism of cavitation control using two bio-inspired riblet morphologies positioned in different orientations and locations on the cylinder. For the first time, the effects of these tiny structures on the flow dynamics and the associated cavitation process were scrutinized. This showed that scalloped riblets, with their curved design, induced secondary vortices near their tips and distorted primary streamwise vortices, and that high velocity gradients near the jagged pattern peaks of sawtooth riblets delayed flow separation, which affected cavitation.

The paper interprets a comparison of two mostly used techniques of a field-oriented control for 6-phase electric drives, with their pros and cons, as well as their differences in construction and behaviour. Both of these approaches have been realized. Frequency and step responses analysis have been demonstrated with a 6-phase permanent magnet synchronous machine. Experimental results have been compared with simulations based on a mathematical model.

pump as turbine (PAT); computational fluid dynamics; variable rotational nominal speed; OpenFoam.

The differential gear train and speed regulating motor constitute the variable ratio transmission for grid-connected wind turbine with differential speed regulation. The synchronous generator in the system can accessing the power grid without frequency converter. The transmission can realize the mode of variable speed constant frequency that the wind rotor speed is varying and the generator rotor speed is constant. The power control method is studied under the different wind speed which is lower or higher than rated wind speed with using the relational expression of utilization rate of wind energy Cp, pitch angle β and the tip speed ratio λ. The SIMULINK software is used to build the 1500 kW wind turbine model with differential speed regulation. Some different wind speed is made as input. The feasibility of power control method for grid-connected wind turbine with differential speed regulation is verified by the comparison between the simulation results and the theoretical value of the key parameters.

Among the major systems of high-speed rail, the arch network relationship, wheel-rail relationship and fluid-structure coupling relationship are important links affecting the performance of high-speed rail, and also the main control factors affecting the speed limit of high-speed rail. From this perspective, the contact state and interactive relationship between pantograph and catenary are the key factors affecting the forward performance of high-speed rail. As a key component in the pantograph system, the actuator is responsible for adjusting the contact force and position between the pantograph and the contact line. The performance characteristics of the actuator, such as response speed, accuracy, stability and durability, directly affect the control performance of the whole pantograph system. In this paper, the research status of the active control technology of high-speed railway pantograph is reviewed, and the future development direction is pointed out, which provides a new idea for the development of pantograph technology.

This paper presents a study on the influence of the frequency variation of a nonlinear1 control allocation technique execution, developed by the author [1], named by Fast Control2 Allocation (FCA) for the Quadrotor Tilt-Rotor (QTR) aircraft. Then, through Software In The3 Loop (SITL) simulation, the proposed work considers the use of Gazebo, QGroundControl, and4 Matlab applications, where different frequencies of the FCA can be implemented separated in5 Matlab, always analyzing the QTR stability conditions from the virtual environment performed in6 Gazebo. TheresultsshowedthattheFCAneedsatleast200HzoffrequencyfortheQTRsafeflight7 conditions, i. e., 2 times smaller than the main control loop frequency, 400 Hz. Lower frequencies8 than this one would case instability or crashes during the QTR Operation.

The need for industrial and commercial machinery to maintain high torque while accurately following a variable angular speed is increasing. To meet this demand, induction motors (IMs) are commonly used with variable speed drives (VSDs) that employ a field-oriented control (FOC) scheme. Over the last thirty years, IMs have been replacing independent connection direct current motors due to their cost-effectiveness, reduced maintenance needs, and increased efficiency. However, IMs and VSDs exhibit nonlinear behavior, uncertainties, and disturbances. This paper proposes a robust combined adaptive passivity-based control (CAPBC) for this class of nonlinear systems that applies to angular rotor speed and stator current regulation inside an FOC scheme for IMs´ VSDs. It uses general Lyapunov-based design energy functions and adaptive laws with σ-modification to assure robustness after combining control and monitoring variables. Lyapunov’s second method and Barbalat Lemma prove that the control and identification error tends to be zero over time. Moreover, comparative experimental results with standard Proportional Integer controller (PIC) and direct APBC, show the proposed CAPBC effectiveness and robustness under normal and changing conditions

In today's human society, diesel generators (DGs) are highly applied into the human energy and electricity supply system due to its technical, operational and economic advantages. This paper proposes an intelligent nonlinear $H_2/H_{\infty}$ robust controller based on the chaos particle swarm gravity search optimization algorithm (CPSOGSA), which controls the speed and excitation of a DG. In this method, firstly, establish the nonlinear mathematical model of the DG and then design the nonlinear $H_2/H_{\infty}$ robust controller based on this. The direct feedback linearization and the $H_2/H_{\infty}$ robust control theory are combined and applied. Based on the design of the integrated controller for DG speed and excitation, the system's performance requirements are transformed into a standard robust $H_2/H_{\infty}$ control problem. The parameters of the proposed solution controller are optimized by using the proposed CPSOGSA. The introduction of CPSOGSA completes the design of an intelligent nonlinear $H_2/H_{\infty}$ robust controller for DG. The simulation is implemented in MATLAB/Simulink, and the results are compared with the PID control method. The obtained results prove that the proposed method can effectively improve the dynamic accuracy of the system and the ability to suppress disturbances and improve the stability of the system.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Doubly-fed induction generators (DFIG) find extensive application in variable-speed wind power plants, providing notable advantages such as cost-effectiveness, operational flexibility across varying speeds, and enhanced power quality. This research focuses on the control of DFIGs employed in variable-speed wind turbine configurations. A suitable mathematical model is chosen for representative systems following a comprehensive review of contemporary research. Subsequent analysis reveals the instability of the open-loop time response of the system. To address this instability, the initial approach involves the implementation of the conventional Model Predictive Controller (MPC). However, the outcomes indicate that this controller falls short of delivering satisfactory performance despite the enhanced stability. In the subsequent phase, efforts are made to mitigate the impact of wind input variability by utilizing the Kalman filter, given its effectiveness in handling high variability. Following this, a novel methodology is introduced, which combines nonlinear MPC with the Lyapunov function. This method is based on the nonlinear model of the system. By using the Lyapunov function in the nonlinear MPC structure, the stability of the designed controller is guaranteed. The simulation results conducted using MATLAB software show that the output variables of the modeled DFIG system achieve stability within a reasonable timeframe applying the input.

Adaptive Cruise Control (ACC) is useful in the most dangerous maneuvers such as braking and acceleration. This study assesses how ACC modifies traffic flows by analysing the differences be-tween manual and autonomous driving in connected and autonomous vehicles (CAVs). Using a platoon of 80 vehicles, tested in pairs on the road, it was possible to define the speed trends during braking and acceleration and the reaction times to the driving maneuvers (PRT, TH, TCC) with a kinematic data detector. The interactions between the CAV and the driver, have been studied in-novatively, i.e through gaze analysis. Situations of potential danger, characterized by the braking of the vehicle that precedes the car with the driver equipped with the eye tracker tool, have been recreated, considering the influence of the driver’s ACC experience. Results statistically confirmed that with the ACC switched on the reaction times are greater than manual driving (2.4/3.8 sec); this can lead to a reduction in road safety, further motivated by the rapid decrease in speed. The interpolation between automated and human data, finally, has allowed the detection of some criticalities of the system that are fundamental in order to reach the second level of automation.

This paper presents the implementation of a control strategy based on fuzzy logic artificial intelligence (AI) for speed regulation of an electromagnetic frequency regulator (EFR) prototype, aiming to eliminate the dependence on knowledge of physical parameters in the most diverse operating conditions. Speed multiplication is one of the most important steps in power generation wind. Gearboxes are generally used for this purpose. However, they have a reduced lifespan and a high failure rate and are still noise sources. The search for new ways to match the speed (and torque) between the turbine and the generator is an important research area to increase the energy, financial and environmental efficiency of wind systems. The EFR device is an example of an alternative technology that this team of researchers has proposed. It counts the fact of taking advantage of the main advantages of an induction machine with the rotor in a squirrel cage positively. In the first studies, the EFR control strategy consisted of the conventional PID controllers, which has several limitations widely discussed in the literature. This strategy also limits the EFR's performance, considering its entire operating range. The simulation program was developed using the Matlab/Simulink platform, while the experimental results were obtained in the laboratory emulating the EFR-based system. The EFR prototype used has 2 poles, a nominal power of 2.2 kW, and a nominal frequency of 60 Hz. Experimental results were presented to validate the efficiency of the proposed control strategy.

Simulator training for image-guided surgical interventions may benefit from artificial intelligence systems that control the evolution of task skills in terms of time and precision of a trainee's performance on the basis of fully automatic feed-back systems. At the earliest stages of training, novice trainees frequently focus on getting faster at the task, and may thereby compromise the optimal evolution of the precision of their performance. For automatically guiding them towards attaining an optimal speed-accuracy trade-off, an effective control system for the reinforcement/correction of strategies must be able to exploit the right individual performance criteria in the right way, reliably detect individual performance trends at any given moment in time, and alert the trainee, as early as necessary, when to slow down and focus on precision, or when to focus on getting faster. This article addresses several aspects of this challenge for speed-accuracy controlled simulator training before any training on specific surgical tasks or clinical models should be envisaged. Analyses of individual learning curves from the simulator training sessions of novices and benchmark performance data of one expert surgeon, who had no specific training in the simulator task, validate the suggested approach.

In the case of long-stator linear drive, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signals transmitted from maglev vehicle can’t meet the need of the real-time propulsion control in the on-ground inverter power substations. In this paper the design of the propulsion inverter control system with a position estimator for driving long-stator synchronous motor in high speed maglev train is proposed. The experiments have been carried out at the 150m long guideway in O-song test track. To investigate the performance of the position estimator, the propulsion control system with and without the position estimator are compared. The result confirms that the proposed strategy can meet the dynamic property need of propulsion inverter control system for driving long-stator linear synchronous motors

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

In the full load operating range, wind turbines typically use pitch control to maintain rotor speed and output power at their rated values to guarantee the whole system’s safety. Blade pitch actuators are subject to physical limitations and safety requirements, which imposes strict constraints on pitch angle’s amplitude and rate of change. These constraints will bring windup problem to the integral part of the pitch controller. It leads to deterioration of the pitch control system’s performance or even the instability problem, especially for large-scale turbines operating in extreme uncertain wind conditions or suffering from cyber attacks. This paper designs an anti-windup robust pitch angle control strategy to deal with pitch rate constraint issue to enhance the security of control system. First, to facilitate controller design, a filtered tracking error technique is employed to transform the nonaffine form into an affine one. Subsequently, a feedback robust controller based on UDE is developed to handle the model’s uncertainty and external disturbances. To address the issue of integral saturation in the pitch system and guarantee its safety, an elliptical bounded constraint is integrated into the designed UDE strategy. This bounded UDE controller can improve the stability of power generation quality, reduces the mechanical loads on components and enhance the whole system’s safety. Finally, the effectiveness of the proposed scheme is verified on the Wind Turbine Blockset platform in Matlab/Simulink. It can achieve better performance than the traditional method.

Rising fuel costs, significant air pollution, and the need to mitigate the negative consequences of oil consumption have diminished the relevance of traditional vehicles. This shift encourages the adoption of safer, more efficient, and eco-friendly transportation alternatives, such as fuel cell, electric, and hybrid vehicles. Brushless direct current motors are gaining popularity due to their high efficiency, power factor, torque, and controllability. By 2030, Brushless Direct Current motors are expected to replace conventional motors as the standard for power transfer, especially in dynamic applications like automobiles, more electric aircraft. This study explores a control technique to improve real-time control of brushless direct current motors in electric vehicles It presents speed control of these system for electric vehicle applications and an overview of electric vehicle technologies. A model for the 120-degree mode was developed using electrical and mechanical equations in MATLAB/Simulink. Three scenarios were examined to assess the potential of controlling brushless direct current motors using constant and dynamic speed and torque. The actual value reached the reference value in the first two scenarios.

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

Air change rate is an important parameter for quantification of ventilation heat losses and also affects the indoor climate of buildings. Indoor air quality is significantly associated with ventilation. If air change isn't sufficient, trapped allergens, pollutants and irritants can degrade the indoor air quality and affect the well-being of a building's occupants. Many studies on ventilation and health have concluded that lower air change rates can have a negative effect on people’s health and low ventilation may result in an increase in allergic diseases. Quantification of air change rate is complicated, since it is affected by a number of parameters, of which the one of the most variable is the air-wind flow. This study aims to determination and comparison of values of the air change rate in two methods - by quantifying of aerodynamic coefficient Cp = Cpe - Cpi – so called aerodynamic quantification of the building and the methodology based on experimental measurements of carbon dioxide in the selected reference room in apartment building.

The aim of this cross-sectional study was to assess the influence of the maturity status on speed, explosive power and change of direction (COD) in 13-year-old football players. Ninety-eight male players (age: 13.1 ± 1.0 y) were divided into late, average, and early maturation groups. Physical fitness testing included the following variables: 10 and 30-meter sprint time and maximum speed in the 20-30 m segment of the 30-meter sprint test, the T-test time, countermovement jump height and horizontal distance in the triple jump. The data showed a significant effect of maturity status on performance in three parameters: in maximum speed in the 20-30 m section (p = 0,024), however, the only significant differences were found between the early-maturation group and average-maturation group (p = 0.033); in the COD (p = 0.024), where significant differences were confirmed between the late-maturation group and the average-maturation group (p = 0.033); in the unilateral triple jump distance of the dominant and non-dominant (p = 0,007 and p = 0.001, respectively) lower limb. For both limbs, significant differences between the late-maturation group and average maturation group (p = 0.005 and p = 0.013, respectively) as well as the late-maturation group and early-maturation group (p = 0.007 and p = 0.045, respectively) were proved. These results indicate that maximal speed, COD speed and unilateral lower limb reactive strength are moderated by biological age in football players aged 13 years.

The main objective of this paper is to continue the development of activities of basic and applied research related to wind energy and to develop methods of optimal control to improve the performance and production of electrical energy from wind. A new control technique of Double fed induction generator for wind turbine is undertaken through a robust approach tagged nonlinear sliding mode control (SMC) with exponential reaching law control (ERL). The SMC with ERL proves to be capable of reducing the system chattering phenomenon as well as accelerating the approaching process. A nonlinear case numerical simulation test is employed to verify the superior performance of the ERL method over traditional power rate reaching strategy. Results obtained in Matlab/Simulink environment show that the SMC with ERL is more robust, prove excellent performance for the control unit by improving power quality and stability of wind turbine.

Tourism has increased in prominence as a key industry that generates employment and encourages economic diversity. The coastline region is a major contributor to worldwide tourism. Since then, coastal areas have been in the forefront of tourism infrastructure development. The presence of a large number of visitors has frequently had a negative influence on the efficient use of available resources. Maya Bay in Krabi Province, southern Thailand, is one example of a coastal area that has suffered from the negative effects of over-tourism Because of the Government of India's plan to place Lakshadweep on the world map of tourism destinations that compete with other archipelagos, it was critical that the current state of tourism in Lakshadweep be studied and precautionary measures be reviewed so that tourism growth does not devolve into over-tourism and Lakshadweep does not follow the same path as Maya Bay.

This report gives a comprehensive summary of two problems about graph convolutional networks (GCNs): over-smoothing and heterophily challenges, and outlines future directions to explore.

DNS is a necessary infrastructure for accessing the Internet. Until now, privacy protection in domain name resolution has mainly focused on end user privacy (communication encryption between clients and DNS full-service resolver). For this reason, communication between DNS full-service resolver and authoritative DNS servers is still done in plaintext. A DNS request from a DNS full-service resolver to an authoritative DNS server does not pose a privacy issue because the source IP address that comes from is the DNS full-service resolver. However, in recent years, there have been reports of specific techniques for identifying the privacy of previously unknown institutions by analyzing the logs of authoritative DNS servers. In order to further strengthen privacy in DNS communication, we proposed an architecture to encrypt all DNS communication in DoH, created a prototype environment, and investigated performance evaluation. The main contributions of this paper are threefold. First, we proposed the Full-DoH DNS architecture. This is a domain name resolution framework designed specifically for institutional privacy. Second, we evaluated the proposed architecture through a prototype implementation. Finally, we discussed related issues to the proposed architecture.

In Taiwan, farmers often apply excess compost to ensure adequate crop yield in highly frequent tillage, highly weathered, and lower fertility soils. The potential of biochar (BC) for diminishing soil C mineralization, and improving soil nutrient availability in compost over-fertilized soil is promising, but the study is still under-examined. To test the hypothesis, 434 days in vitro C mineralization kinetics of incubation experiment were conducted. Woody BC 0%, 0.5%, 1.0% and 2.0% (w/w) made of lead tree (Leucaena leucocephala (Lam.) de. Wit) were added to an Oxisols, and two Inceptisols of Taiwan. In each treatment, 5% swine manure compost (2 times recommended amount) was added and served as the over-fertilized soil. The results indicated that soil type strongly influenced the impact of BC addition on soil carbon mineralization potential. Respiration per unit of total organic carbon (total mineralization coefficient, TMC) of three studied soils significantly decreased with BC addition increased. Principal component analysis (PCA) suggested that for retaining more plant nutrients in addition to the effects of carbon sequestration, it is recommended that farmer could use locally produced biochars and composts in highly weathered and highly frequent tillage soil. Adding 0.5%-1% woody BC in soil should be reasonable and appropriate.

In Taiwan, farmers often apply excess compost to ensure adequate crop yield in highly frequent tillage, highly weathered, and lower fertility soils. The potential of biochar (BC) for diminishing soil C mineralization, and improving soil nutrient availability in compost over-fertilized soil is promising, but the study is still under-examined. To test the hypothesis, 434 days in vitro C mineralization kinetics of incubation experiment were conducted. Woody BC 0%, 0.5%, 1.0% and 2.0% (w/w) made of lead tree (Leucaena leucocephala (Lam.) de. Wit) were added to an Oxisols, and two Inceptisols of Taiwan. In each treatment, 5% swine manure compost (2 times recommended amount) was added and served as the over-fertilized soil. The results indicated that soil type strongly influenced the impact of BC addition on soil carbon mineralization potential. Respiration per unit of total organic carbon (total mineralization coefficient, TMC) of three studied soils significantly decreased with BC addition increased. Principal component analysis (PCA) suggested that for retaining more plant nutrients in addition to the effects of carbon sequestration, it is recommended that farmer could use locally produced biochars and composts in highly weathered and highly frequent tillage soil. Adding 0.5%-1% woody BC in soil should be reasonable and appropriate.

The article presents the original derivation method of transformations for kinematics with a universal reference system. This method allows to derive transformations that meet the results of the Michelson-Morley and Kennedy-Thorndike experiments only in some frame of reference, e.g. in laboratories moving in relation to a universal frame of reference with small speeds. The obtained transformations are the basis for the derivation of the new physical theory, which has been called the Special Theory of Ether. The generalized transformations can be expressed by relative speeds (26)-(27) or by the parameter δ (v) (37)-(38). Based on conclusions of the Michelson-Morley’s and Kennedy-Thorndike’s experiments, the parameter δ (v) was determined. This allows the transformations to take a special form (81)-(82), which is consistent with experiments in which velocity of light is measured. On the basis of obtained transformations, the formulas for summing speed and relative speed were also determined. The entire article includes only original research conducted by its author.

Antibiotic-sparing treatments are required to prevent the further emergence of anti-microbial resistance in Neisseria gonorrhoeae. Commensal Neisseria species have previously been found to inhibit the growth of pathogenic Neisseria species. For example, a previous study found that 3 out of 5 historical isolates of Neisseria mucosa could inhibit the growth of N. gonorrhoeae. In this study, we used agar overlay assays to assess if 24 circulating and historical isolates of Neisseria mucosa could inhibit the growth of 28 circulating and historical isolates of N. gonorrhoeae. Although pitting around each colony of N. mucosa created an optical illusion of decreased growth of N. gonorrhoeae, we found no evidence of inhibition (n=24). In contrast, positive controls of Streptococcus pneumoniae and Escherichia coli demonstrated a strong inhibitory effect against the growth of N. gonorrhoeae.

We propose a 10-Gb/s 64-quadrature amplitude modulation (QAM) signal-based Radio over Fiber (RoF) system for 50 km of standard single mode fiber length which utilizes Reinforcement Learning (RL) SARSA based decision method to indicate an effective decision which mitigates nonlinearity. By utilizing RL-SARSA algorithm, the results demonstrate that significant reduction can be obtained in terms of bit error rate.

Machine learning (ML) methodologies have been looked upon recently as a potential candidate for mitigating nonlinearity issues in optical communications. In this paper, we experimentally demonstrate a 40-Gb/s 256-quadrature amplitude modulation (QAM) signal-based Radio over Fiber (RoF) system for 50 km of standard single mode fiber length which utilizes support vector machine (SVM) decision method to indicate an effective nonlinearity mitigation. The influence of different impairments in the system is evaluated that includes the influences of Mach-Zehnder Modulator nonlinearities, in-phase and quadrature phase skew of the modulator. By utilizing SVM, the results demonstrated in terms of bit error rate and eye linearity suggest that impairments are significantly reduced and licit input signal power span of 5dBs is enlarged to 15 dBs.

L-glutamate is one the most important excitatory neurotransmitter at central nervous system level and it is implicated in several pathologies. So, it is very important to monitor its variations, in real time in animal models’ brain. Amperometric biosensors have been used because of their very high temporal and spatial resolution, and because suitable for a short to mid-term implantation. The present study aimed to develop and characterize a new glutamate biosensor design that exploits the selectivity of Glutamate Oxidase (GluOx) for l-glutamate, and the capability of a small molecule as propylene glycol (PG) to influence and extend the stability and the activity of enzyme. Different designs were evaluated by modifying the main components in their concentrations to find the most suitable design. Moreover, enzyme concentrations from 100 U/ml up to 200 U/ml were verified and different PG concentrations (1%, 0.1% and 0.05%) were tested. The most suitable selected design was Pt_c/PPD/PEI(1%)₂/GlutOx₅/PG(0.1%) and it was compared to the same already described design loading PEDGE, instead of PG, in terms of over-time performances. PG has proved to be capable of determining an over-time stability of the glutamate biosensor in particular in terms of linear region slope (LRS) up to 21 days.

This work examines the impact of the nozzle-substrate distance (NSD) on the structural, optical and electrical properties of fluorine-doped tin oxide (FTO) thin films. The films were grown by spray pyrolysis with the chemical formulation of “Streaming Process for Electroless and Electrochemical Deposition technology” (SPEED) technique. The characterization technique such as XRD, SEM, UV-spectrophotometry and Hall Effect measurement were employed for studying the structural, optical and electrical properties of the FTO films at various NSD. The NSD was varied from 25-32cm amid the experiment. All FTO films are polycrystalline, tetragonal crystal structure with strong orientation along the (211) reflection. SEM properties study demonstrated slight reliance on NSD and have uniform films which are a disciple to substrate at NSD of 27 and 30 cm, however, crumbled at 25cm and 32cm NSD. They likewise displayed a mud-look like morphology and smooth white appearance. The average optical transmittance of all films is over 80% in the noticeable at UV range. The band gap investigation demonstrates the average value of 3.5eV and the resistivity was found to diminish with increasing NSD at 30 cm. Both mobility and carrier concentration of the FTO films follow a similar trend. The average figure of merit of 4.98 was obtained which is an improvement based on our previous results. The FTO samples grown at 27 and 30 cm NSD in this work are best FTO samples and hence could serve as a promising candidate in dye sensitized solar cells. Therfore, graphene has been employed in different concentrations in our ongoing FTO optimization research so as to further improve on the FTO’s figure of merit.

In Yaoundé, Cameroon, excessive and inappropriate speeding remains a major public health concern. Part of the problem are the unsafe speed limits, lack of evidence, and effective evaluation of speeding safety performance indicators (SSPIs), and the absence of speed management, hindering the city's ability to mitigate the risks associated with speeding. This study aimed to address this knowledge gap by assessing SSPIs using a well-defined methodology and suggesting speed management strategies. Data on speed, traffic volumes and road attributes were collected from a random selection of 16 representative road sections in Yaoundé. Seven SSPIs were calculated, and weights were assigned to evaluate city-level SSPIs. The findings showed that 66.8% of drivers drive within the speed limit, generally operating at speeds of 54 km/h with a speed variation of 26 km/h. Based on the speed analysis, evidence-based strategies are proposed, and implementing these strategies could potentially reduce fatalities and serious injuries by 16% to 84% across study locations, as indicated by Elvik's model. These findings have significant policy implications for reducing speeding in Yaoundé, and the methodological approach can be replicated in other urban settings. Future research should extend SSPI evaluation to the national level and test the effectiveness of the recommended strategies.

The ultimate goal of our review is to draw clinician’s attention, especially of those who are managing pediatric patients with permanent, long-standing, ventriculoperitoneal or, less commonly, ventriculo-atrial shunts. This specific subgroup of patients may eventually suffer from severe, intractable headaches which may negatively impair their quality of daily living. In the absence of any other clinical condition that could be attributed as the cause of the headache, shunt overdrainage should not be overlooked but, on the contrary, should be seriously taken into consideration in the therapeutic armamentarium of such cases, that are difficult to be handled.

Background A body composition monitor (BCM) has a role not only in determining over-hydration (OH) but also as an aid to nutritional assessment. For dialysis patient-specific clinical applications of BCM, it is necessary to clarify the relationship between body composition parameters and OH in healthy Chinese individuals. Methods This cross-sectional study involved 314 healthy individuals with a mean age of 45.7±13.1 years. BCM measurements were performed while the subjects were fasting. Results The mean OH level was 0.379±0.81 L. Lean tissue index (LTI) and Lean tissue mass (LTM) were significantly higher in males (p<0.001), while fat tissue index (FTI) was significantly higher in females (p<0.001). In univariate correlation analysis, FTI, Fat, and ATM had a negative correlation with OH in females and all subjects (p<0.05), while LTM and BCM had a positive correlation in all subjects (p<0.05). There was a significant negative correlation between phase angle (PhA) and OH in males, females, and all subjects (r=-0.634, p<0.001; r=-0.666, p<0.001; r=-0.484, p<0.001, respectively). In multivariate linear regression analysis, PhA (b=-1.266, p<0.001), LTM (b=0.987, p<0.001), age (b=-0.307, p<0.001) were independent predictors of OH. Conclusions This study demonstrated that age, LTM and especially PhA, had important roles in predicting OH in healthy Chinese individuals. In the future, PhA may aid in clinical assessment by helping to titrate dry weight among hemodialysis patients with malnutrition.

By using directed dimensional analysis and data fitting, an explicit universal scaling law for the velocity of dominoes toppling motion is formulated. The scaling law shows that domino propagational velocity is linear proportional to the 3/2 power of domino separation, and -1/2 power of domino height and thickness. The study also proved that dominoes width and mass have no influence to the domino wave traveling velocity.

A Savonius wind turbine is one of the simplest vertical-axis turbines. Several researchers have been attracted to it because of its simple structure, low noise, appropriate torque, and independence from wind direction. SR3345 and SR5050 blade profiles will be investigated for their effects on the performance of Savonius wind turbines. First, the fabricated wind turbine is placed in front of an open circuit wind tunnel with a velocity of 6 m/s. Furthermore, governing relationships are used to calculate power and torque coefficients as well as tip speed. In this study, the power and torque coefficients of the turbine are compared with the two profiles considered based on overlap ratios between 0 and 0.3. Despite its increased stability, the central shaft reduced the power coefficient of the turbine. For blade SR3345, the best performance occurs at tip speed ratios of less than 1, while for blade SR5050, the best performance occurs at higher tip speed ratios. Both blades SR3345 and SR5050 achieve the highest power coefficients at overlap ratios of 0 and 0.18 when a central shaft is present.

This research investigates the socio-economic impact of rattan cane processing on the livelihoods of practitioners in Ibadan Metropolis. It comprehensively assesses raw material availability, examines factors influencing demand and supply, and evaluates sales to determine the profitability of rattan processors. With the snowball and total enumeration sampling methods, the study engages with a diverse group of rattan processors. The study reveals a concerning 36% acknowledgement of a decline in the availability of canes attributed to deforestation and over-exploitation. Notably, it emphasizes that rattan product manufacturing in Ibadan Metropolis operates at a craft level, employing tools like saws, hammers, knives, gas cylinders, pinches, and tape rules, impacting production efficiency and product longevity. Additionally, the research underscores the absence of government support and credit facilities reported by all respondents. The Market Margin analysis highlights varying profitability levels across rattan products, with chairs exhibiting notably higher profitability (32.22%) than others. Individual profit margins for specific products, such as chairs (145.00%), underscore the significance of processing costs, production time, and market demand. The study offers strategic recommendations, advocating for district-level service centres for training, technology transfer, and support to enhance skills and technical efficiency. It calls for government intervention through incentives, facilities, tax breaks, and policies to fortify the rattan trade, improving production standards and unlocking export market potential. Furthermore, financial support, technical assistance, and mechanization should be employed to reduce production costs and time, ultimately elevating income generation in the rattan industry. This research contributes valuable insights to the discourse on sustainable livelihoods and economic viability within the rattan sector.

Transit-oriented development (TOD), such as metro depot and over-track building complexes, has expanded rapidly in China. Over-track building construction has the advantage of comprehensive utilization of land resources, ease of commuting to work, and provide funds for subway construction. However, there still has a pending problem, disturbance of railway vibration, for TOD. Excessive noise and vibration seriously affect people’s life. To address this challenge, field measurements are used to obtain the vibration source characteristics and vibration propagation of the ground and the superstructure in this study. And the typical metro depot with over-track building in Wuhan was selected. The effects of vibration on the surrounding ground and adjacent buildings caused by the operation of trains have been measured, and the propagation law of train-induced ground vibration acceleration in the time and frequency domains has been analyzed. The distribution and propagation laws of vibration noise, structural noise and secondary structure noise in sensitive areas such as the throat area, depot area, test section and access section of the over-track buildings and their impact laws on the over-track buildings are obtained. And the effectiveness of the vibration and noise reduction methods used were evaluated. Results show that within 43 m from the train running track, the train running induced vertical vibration acceleration level in the high-rise building peak size of 58.8 dB, the average value of 55.62 dB; vibration frequency components are mainly 40-60 Hz. The findings might provide useful insight for designing vibration mitigation systems in new metro depots with over-track buildings.

Diabetes is a serious health problem throughout the world, including in Indonesia. The International Diabetes Federation (IDF) reports that the number of adults with diabetes is increasing every year. The Behavioral Risk Factor Surveillance System (BRFSS) is a survey conducted by the Centers for Disease Control and Prevention (CDC) in the United States. Classification methods in data mining techniques are used to classify diabetics and non-diabetics. The data mining process is carried out by preprocessing, feature selection, and dataset classification stages. In the preprocessing stage, data cleaning, data formatting, and data oversampling are carried out using the Synthetic Minority Over-sampling Technique (SMOTE). Next, the feature selection stage is carried out using the Particle Swarm Optimization (PSO) algorithm to find the best attributes. The dataset classification stage is carried out using the CART Model Decision Tree algorithm. The results of the performance evaluation of the CART algorithm are calculated using the confusion matrix and the MAE value, the results obtained for the CART algorithm without SMOTE and PSO obtained the best accuracy of 75.34% and the MAE value of 0.2466, while the CART algorithm using SMOTE and PSO can increase accuracy by 10 .94% to 86.28% and an MAE value of 0.1372.

The upregulated expression of thyrosine kinase AXL has been reported in several hematologic and solid human tumors including gastric, breast, colorectal, prostate, and ovarian cancers. Thus, AXL can potentially serve as a diagnostic and prognostic biomarker for various cancers. This paper reports the first-ever use of loop-mediated isothermal amplification (LAMP) of the AXL gene as a diagnostic method for ovarian cancer. We demonstrated simple instrumentation toward a point-of-care device to perform LAMP. This paper also reports the first-ever use of core-shell beads as a microreactor to perform LAMP as an attempt to promote environmentally friendly laboratory practices.

Use of Machine Learning (ML) methodologies in optical communications has paved a new pathway. In this paper, firstly, we discuss the use of ML methodologies for reducing optical fiber nonlinearities, nonlinearity compensation, fault detection and optical performance monitoring. Then we present our recent work where we compare RL-SARSA and SVM based method with conventional method. The results show that RL-SARSA and SVM methods are successful candidates in mitigating the nonlinearities in proposed system as compared to conventional optical communication system.

Extreme overvalued beliefs (EOB) are rigidly-held, shared beliefs that are the motive behind most acts of terrorism and mass shootings. EOBs are differentiated from delusions and obsessions. The concept of overvalued idea was first described by Wernicke and later applied to terrorism by McHugh. Our group of forensic psychiatrists (Rahman, Resnick, Harry) refined the definition as an aid in the differential diagnosis seen in acts of violence. The form and content of EOBs is discussed as well as group effects, conformity and obedience to authority. Religious cults such as: The People’s Temple, Heaven’s Gate, Aum Shinrikyo, Islamic State (ISIS) and conspiracy beliefs such as assassinations, moon-hoax and vaccine-induced autism beliefs are discussed using this construct. Finally, some concluding thoughts on countering violent extremism, including its online presence is discussed utilizing information learned from online eating disorder and consumer experience.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

The predictability of wind information in a given location is essential for the evaluation of a wind power project. Predicting wind speed accurately improves the planning of wind power generation, reducing costs and improving the use of resources. This paper seeks to predict the mean hourly wind speed in anemometric towers (at a height of 50 meters) at two locations: a coastal region and one with complex terrain characteristics. To this end, the Holt-Winters (HW), Artificial Neural Networks (ANN) and Hybrid time-series models were used. Observational data evaluated by the Modern-Era Retrospective analysis for Research and Applications-Version 2 (MERRA-2) reanalysis at the same height of the towers. The results show that the hybrid model had a better performance in relation to the others, including when compared to the evaluation with MERRA-2. For example, in terms of statistical residuals, RMSE and MAE were 0.91 and 0.62 m/s, respectively. As such, the hybrid models are a good method to forecast wind speed data for wind generation.

In the context of the French tertiary decree, it is crucial to reduce the energy consumption of buildings by first addressing the design of the electrical architecture. Implementing Direct Current (DC) nanogrids in buildings could offers a promising advantage for energy efficiency, significantly impacting overall energy consumption and sustainability goals. For an insulated area with a subtropical climate, such as La Réunion island, DC nanogrids could also facilitate the insertion of local renewable energy sources, especially solar energy. This article presents the deployment and efficiency evaluation of an end-to-end Low Voltage Direct Current (LVDC) nanogrid, from conception to real-world installation within a company. The nanogrid consists of a photovoltaic power plant, a Lithium-Iron-Phosphate (LFP) battery, and DC end-use equipment such as LED lighting and DC fans for two individual offices. An innovation is provided for the power supply and energy management of terminal equipment using the Power Over Ethernet (PoE) standard IEEE 802.3bt. The efficiency of the nanogrid is measured to be 40% higher than the efficiency of an installation powered by PV and distributed at 230 VAC. These results are obtained under certain deployment conditions, which are discussed in this article, in order to enhance the energy efficiency of buildings by using 48VDC. The nanogrid hardware and software infrastructure, the methodology employed for efficiency quantification and the measurement results are described in the paper.

The largest gene families in plants were found to be Glutathione transferase (GSTs), which played significant roles in regulating plant growth, development, and stress response. Within the GSTs gene family, members were found to play a crucial role in the low-temperature response process of plants. A comprehensive study identified a total of 70 BraGSTs genes. Cluster analysis results demonstrated that the BraGSTs in Brassica rapa(B.rapa) could be categorized into eight sub-families and were unevenly distributed across ten chromosomes. The 39 BraGSTs genes were found to be organized into 15 tandem gene clusters, with the promoters containing multiple cis-elements associated with low-temperature response. Cold stress was observed to stimulate the expression of 15 genes, with the BraGSTF2 gene exhibiting the highest level of expression, sug-gesting its significant involvement in winter B.rapa's response to low-temperature stress. Sub-cellular localization analysis of the BraGSTF2 protein indicated its potential expression in both the cell membrane and nucleus. The analysis of stress resistance in BraGSTF2 transgenic Arabidopsis thaliana lines emon-strated that the over-expression of this gene resulted in significantly elevated levels of SOD, POD activity, and SP content compared to the wild type following exposure to low temperatures. These levels reached their peak after 24 hours of treatment. Conversely, the MDA content was lower in the transgenic plants compared to the wild type. Additionally, the survival rate of BraGSTF2 transgenic Arabidopsis thaliana was higher than that of the wild type, suggesting that the BraG-STF2 gene may play a crucial role in enhancing the cold stress tolerance of winter B. rapa. This study lay a foundation for further study on the role of BraGSTs gene in the molecular regulation of cold resistance in winter B.rapa.

In the context of partial autonomy, where autonomous vehicles and humans share control of the vehicle, bringing out-of-the-loop drivers back into the loop is a significant challenge. While warning signal design guidelines are commonly used to provide alerts, few studies have examined each signal in depth with an emphasis on the autonomous environment. This study aims to fill this gap by investigating visual, auditory, and tactile stimuli and modifying their sub-attributes to explore variations related to age, gender, and other individual backgrounds. A driving simulator was utilized to create a realistic driving environment and measure participants' reaction times in takeover request situations. Analysis of the data revealed correlations between age and reaction times for auditory and tactile signals, with interaction effects observed between age and sub-attribute intensity. Additionally, participants exhibited varying reaction time patterns in response to different sub-attribute intensities. By evaluating individual differences in perception based on modality characteristics, often overlooked in prior research, this study serves as a foundational contribution to future research in the field.

Thyroid hormones have a catabolic effect on bone homeostasis. Hence, this study aimed to evaluate serum vitamin D, calcium, and phosphate and bone marker levels and bone mineral density (BMD) among patients with different thyroid diseases. This cross-sectional study included patients with underlying thyroid diseases (n=64, hyperthyroid; n=53 euthyroid; and n=18, hypothyroid) and healthy controls (n=64). BMD was assessed using z-score and left hip and lumbar bone density (g/cm2). Results showed that the mean serum vitamin D Levels of all groups was low (<50 nmol/L). Thyroid patients had higher serum vitamin D levels than healthy controls. All groups had normal serum calcium and phosphate levels. The bone marker levels were significantly high in the hyperthyroid group and low in the hypothyroid group. The z-score for hip and spine did not significantly differ between thyroid patients and control groups. The hip bone density was remarkably low in the hyperthyroid group. In all groups, the serum vitamin D levels were below the cutoff value. However, thyroid patients had a higher serum vitamin D level than healthy controls. The carboxy terminal collagen crosslink and procollagen type I N-terminal propeptide levels were high in hyperthyroid patients and low in hypothyroid patients. Further, hyperthyroid patients had a low hip BMD.

Studies show that although female soccer players often have shorter change of direction (COD) deficits than males, indicating different biomechanical profiles, there is lack of research on the impact of physical metrics on COD performance in females. The aim of this study was to analyze whether performance metrics based on speed, and jumping could explain the variation in %CODD in young female soccer players. Thirty-three highly trained adolescent female soccer players (age: 16. ± 0.95 years; height: 160.4 ± 5.22 cm; body mass: 55.7 ± 7.22 kg) performed COD180 tests, 10-m and 30-m sprint test and single leg countermovement and horizontal jumps. Acceleration in the first 10 meters of a sprint was identified as a significant predictor of COD180 performance (R2 = 28%), (R2 = 50%), (p

Background - Technological developments induced lifestyle changes and increase population physical inactivity. This change in lifestyle can affect the male-female morphological and physical fitness differences. The aim of this study is to determine and to compare the effect of sex differences in percentage of body fat on speed and endurance running performance. Methods - 72 male and 64 female students aged 20 to 23 years participated in this study. After assessing their morphological characteristics, running performances during 30 m and 400 m, and maximum aerobic velocity (MAV) and maximal oxygen consumption (VO2max) during a 20 m shuttle running test have been estimated for each subject. Male students were re-tested after being overweighed down with a weight equivalent to the mean differences in body fat recorded between the two sexes in the form of a loaded worn vest. Results – Male presented a percentage of fat mass (17.2 ±2%) significantly (p <0.001) lower than that of women subject (25.0 ±2.5%). Running performances during 30 m and 400 m, MAV and VO2max were significantly (p<0.001) better in males. During the weighted condition, male performances during 30 m and 400 m, MAV and VO2max were attenuated by 6.89%, 14.16%, 6.48% and 10.07%, respectively but remain significantly better than those of female students. Conclusion - The persistence of sex differences after overweighting male students indicates that body fat could be responsible for ≈ 50 to 70% of the observed differences between sexes performances during short and long sprints, and 20 m shuttle running test.

The visual span refers to the number of letters readers can identify in a single fixation without using linguistic skills. Proponents of the visual span hypothesis postulate an influence of early visual processing on reading speed. Given the slowness of reading Arabic texts, the present work aims to study the development of the visual span and its effects on reading speed in the Arabic-speaking context. Thirty-four subjects participated in the study. The trigram task and the rapid serial visual presentation (RSVP) paradigm were used to estimate visual span size and reading speed. In line with our initial assumptions, the results showed a significant effect of grade level on reading speed (F(2,31) = 30.93, p<0.001), visual span size (F(2,31) = 20.57, p<0.001). In good alignment with previous work, our results show that visual span size could explain around 40% of the reading speed variability. Interestingly, our analyses revealed a narrowing of visual span size in our Arabic sample. The results of study 2, suggest that the poor performance in the trigram task is due to poor visual attention capacities in our Arabic readers

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

1) We shall discuss what modern interpretations say about the Heisenberg's uncertainties. These interpretations explain that a quantity begins to 'lose' meaning when a conjugate property begins to 'acquire' definite meaning. We know that a quantity losing meaning means that it has no fixed value and has an uncertainty . In this paper we look deeper into this interpretation and the outcome reveals more evidence of the quantity losing meaning. Newer insights appear. 2) We consider two extreme cases of hypothetical processes nature undergoes, without interference by a measurement: One, a system collapses to an energy eigenstate under the influence of a Hamiltonian instantaneously at a time $t$. This is thus what would happen if we would measure the system's energy. Next, when a particle becomes localised to a point at a time $t_0$ under the influence of a Hamiltonian. This is thus what would happen if we would measure the system's position. We shall prove that both these situations cannot arise under ordinary circumstances and thus measurement processes cannot be modelled by physical Hamiltonians.

An axiomatic theory is proposed that reconciles the existence of an absolute scale for time (Planck time) and special relativity. According to this theory speed of light c becomes a variable which is proposed to be taken as the fifth dimension.

Background: Interventions with the performance of sessions with sprints in different intensity manipulations, can be a great alternative to improve physical performance. Objective: To verify the influence of different break times between sprints on the performance of amateur futsal athletes Methods: 10 individuals, men, amateur futsal athletes (Age: 21.5 ± 1.6; Weight: 72.4 ± 6.88; Height: 1.72 ± 0.05; BMI: 24.3 ± 1.2; Fat%: 13.7 ± 3.3, VO2peak: 49.1 ± 10.5) participated in the study. For the intervention, individuals were randomly selected to perform sessions with sprints (10 sets 20 meters) with different pause times, being 15 (S15), 30 (S30) and 60 (S60) seconds. For performance analysis, the speed (km / h) applied to each sprint was used, monitored by a device with a photocell (CEFISE Biotecnologia Esportiva®, Nova Odessa, São Paulo) and the statistical treatment of all data was through the software Statistica 7.0 (Statsoft ™, Tulsa, OK, USA) using a significance level of p≤0.05. Results: There was an interaction between speed and interval time (p = 0.000). For condition S15, a greater reduction in performance was observed (p≤0.05), while for S30 and S60, no significant reduction in performance was observed (p> 0.05). The data for the area under the curve showed a significant difference (p = 0.000), where the interval of 60 seconds (S60) was longer compared to the values of 30 (S30) (p = 0.000) and 15 seconds (S15) (p = 0.000). However, there were no significant differences between the 30 and 15 second data (p = 0.248). Conclusion: Shorter time (15 seconds) of interval between repeated sprints can significantly affect performance when compared to longer breaks (30 and 60 seconds). But, all the conditions tested here, can be positive for the improvement of the performance, mainly in sports that demand fast and efficient motor actions, as for example, futsal.

Diabetes is a risk factor for mild cognitive impairment (MCI) and dementia. However, how the clinical characteristics of type 2 diabetic patients with MCI are linked to sarcopenia and/or its criterion remain to be elucidated. Japanese patients with type 2 diabetes mellitus were categorized into the MCI group for MoCA-J (the Japanese version of the Montreal cognitive assessment) score <26, and into the non-MCI group for MoCA-J ≥26. Sarcopenia was defined by a low skeletal mass index along with low muscle strength (handgrip strength) or low physical performance (walking speed <1.0 m/s). Univariate and multivariate-adjusted odds ratio models were used to determine the independent contributors for MoCA-J <26. Among 438 participants, 221 (50.5%) and 217 (49.5%) comprised the non-MCI and MCI groups, respectively. In the MCI group, age (61 ± 12 vs. 71 ± 10 years, p < 0.01) and duration of diabetes (14 ± 9 vs. 17 ± 9 years, p < 0.01) were higher than those in the non-MCI group. Patients in the MCI group exhibited lower hand grip strength, walking speed, and skeletal mass index, but higher prevalence of sarcopenia. Only walking speed (rather than muscle loss or muscle weakness) was found to be an independent determinant of MCI after adjusting for multiple factors, such as age, gender, BMI, duration of diabetes, hypertension, dyslipidemia, smoking, drinking, eGFR, HbA1c, and history of coronary heart diseases and stroke. In subgroup analysis, a group consisting of male patients aged ≥65 years, with BMI <25, showed a significant OR for walking speed. This is the first study to show that slow walking speed is a sole determinant for the presence of MCI in patients with type 2 diabetes. It was suggested that walking speed is an important factor in the prediction and prevention of MCI development in patients with diabetes mellitus.

We analyze real telematics information for a sample of drivers with usage-based insurance policies. We examine the statistical distribution of distance driven above the posted speed limit – which presents a strong positive asymmetry – using quantile regression models. We find that, at different percentile levels, the distance driven at speeds above the posted limit depends on total distance driven and, more generally, on such factors as the percentages of urban and nighttime driving and on the driver’s gender. However, the impact of these covariates differs according to the percentile level. We stress the importance of understanding telematics information, which should not be limited to simply characterizing average drivers, but can be useful for signaling dangerous driving by predicting quantiles associated with specific driver characteristics. We conclude that the risk of driving long distances above the speed limit is heterogeneous and, moreover, we show that prevention campaigns should target primarily male, non-urban drivers, especially if they present a high percentage of nighttime driving.

Abstract: The ever-increasing use of motor vehicles causes a number of traffic safety and community issues, which are particularly severe in cities, accompanied with scarcity of parking spaces and challenges encountered in the road layout alteration projects. The commonly applied solutions include designation of through streets and implementation of on-street parking on residential streets and retrofitted traffic calming measures (TCMs). This article presents the results of the study conducted on a two-way street where Metered Parking System MPS was implemented together with diagonal and parallel parking spaces, refuge islands, horizontal deflection and lane narrowing by a single-sided chicane. The aim of this study was to identify those TCMs that effectively helped to reduce the island approach speed. Heuristic method was applied to assess the effect of the respective TCMs on reducing the island approach speed and the key speed reduction determinants were defined using cause and effect diagram and Pareto chart. Comparative analyses were carried out to rate the respective TCMs as effective, moderately effective or ineffective. Section 1 of this article presents the output of the literature review on urban parking analyses and TCM efficacy. Section 2 presents the study site and the applied heuristic method. The study results are presented in Section 3. Section 3 defines the determinants on the cause and effect diagram and analyses the determinants using the Pareto chart. The final conclusions and comments are given in Section 5. Although the study was limited to a single street in Poland, the findings may hold true in other countries where similar TCMs are used.

Spinal cord injuries (SCI) can result in sensory and motor dysfunctions, which were long-considered permanent. Recent advancement in electrical neuromodulation has been proven to restore sensorimotor function in people with SCI. These stimulation protocols, however, were mostly invasive, expensive, and difficult to implement. In this study, transcutaneous electrical stimulation (tES) was used to restore over-ground walking of an individual with 21 years of chronic paralysis from a cervical SCI. After a total of 66 weeks of rehabilitation training with tES, which included standing, functional reaching, reclined sit-up, treadmill walking and active biking, significant improvement in lower-limb volitional movements and overall light touch sensation were shown by International Standards for Neurological Classification of Spinal Cord Injury (ISNCSCI) score. By the end of the study, the participant could walk in a 4-meter walking test with the aid of a walking frame and ankle foot orthoses. The success in the sensorimotor recovery of our study participant sheds light on the future of non-invasive neuromodulation treatment for SCI paralysis.

Premenstrual syndrome is characterized by pain and symptoms affecting the women´s quality of life. We aimed to evaluate the safety and effectiveness of an oral fixed dose combination containing naproxen 220 mg + paracetamol 300 mg + pamabrom 25 mg tablet (Analgen Fem®) during the routine clinical practice. A prospective, open-label, multicenter, observational post-marketing study was conducted from December 2017 to December 2019 including 270 women older than 18 years. Primary endpoint was the proportion of adverse events, meanwhile the pain intensity, premenstrual syndrome symptoms, and patient proportion with a pain score reduction by at least 50% were secondary endpoints. The mean age of population was 28.9 ± 8.8 years. Among the 270 women, 8 (3%) experienced 10 adverse events. These were headache (5/8), gastritis (2/8) dyspepsia (1/8), diarrhea (1/8) and nausea (1/8). The investigator discontinued the study medication in 3/8 patients because of adverse events. The median of differences between the pain intensity at baseline and at last observation (-4.5, 95%CI; -5, -4) demonstrated that naproxen 220 mg + paracetamol 300 mg + pamabrom 25 mg fixed dose combination reduced pain intensity (p<0.001). In addition, the proportion of patients with pain reduction by at least 50% at the end of the treatment was 70.7%. The study demonstrated that this drug represents a safe and tolerated treatment, reducing pain intensity and premenstrual symptoms.

Fragility scales are intended to help in therapeutic decisions. Here we asked if the fragility as-sessment in MM patients ≥75 years old qualified for treatment by the local physician correlates with the choice of treatment: a 2- or 3-drug regimen. Between 7/2018 to 12/2019 we prospectively enrolled 197 MM patients at the start of treatment from the 13 Polish Myeloma Group centers. The data to assess fragility were prospectively collected, but centrally assessed fragility was not disclosed to the local center. The activity of daily living (ADL) could be assessed in 192 (97.5%) and was independent in 158 (80.2%), moderately impaired in 23 (11.7%), and 11 (5.6%) in com-pletely dependent. Patients with more than 3 comorbidities were 26.9% (53 patients). Thus, ac-cording to the Palumbo calculator, 43 patients were in the intermediate-fitness group (21.8%), and the rest belonged to the frailty group (153, 77.7%). Overall, 79.7% of patients (157) received 3-drug regimens and 20.3% (40) received 2-drug regimens. In each ECOG group, more than 3/4 of patients received 3-drug regimens. According to the ADL scale, 82.3% of the independent 65.2% of moderately impaired, and 81.8% of the dependent received 3-drug regimens. Out of 53 pa-tients with at least 4 comorbidities, 71.7% received 3-drug regimens, and the rest 2-drug regi-mens. Three-drugs regimens received 34 patients from the intermediate-fit group (79.0%), and 123 (79.9%) from the frail group. Early mortality occurred in 25 patients (12.7%). No one discon-tinued treatment due to toxicity. To conclude, MM patients over 75 are mainly treated with tri-ple-drug regimens, not only in reduced doses, regardless of their frailty scores. However, the absence of prospective fragility assessment did not negatively affect early mortality and the number of treatment discontinuations which questions the clinical utility of current fragility scales in everyday practice.

Drivers of L3 automated vehicles (AVs) are not required to continuously monitor the AV system. However, they must be prepared to take over when requested. Therefore, it is necessary to design an in-vehicle environment that allows drivers to adapt their levels of preparedness to the likelihood of control transition. This study evaluates ambient in-vehicle lighting that continuously communicates the current level of AV reliability, specifically on how it could influence drivers' take-over performance and mental workload (MW). We conducted an experiment in a driving simulator with 42 participants who experienced 10 take-over requests (TORs). The experimental group experienced a four-stage ambient light display that communicated the current level of AV reliability, which was not provided to the control group. The experimental group demonstrated better take-over performance, based on lower vehicle jerks. Notably, perceived MW did not differ between the groups, and the EEG indices of MW (frontal theta power, parietal alpha power, Task-Load Index) did not differ between the groups. These findings suggest that communicating the current level of reliability using ambient light might help drivers be better prepared for TORs and perform better without increasing their MW.

A lot of previous research have proposed various frameworks and algorithms to optimize routes to reduce the total transportation cost, which accounts for over 70% of overall logistics cost. However, it is very hard to find the cases applied the mathematical models or algorithms to the practical business environment cases, especially daily operating logistics services like convenient stores. Most of previous research have considered the developing an optimal algorithm which can solve the mathematical problem within the practical time while satisfying all constraints such as the capacity of delivery and pick-up, and time windows. For the daily pick-up and delivery service like supporting several convenient stores, it is required to consider the unit transporting container as well as the demand, capacity of trucks, traveling distance and traffic congestion. Especially, the reusable transporting container, trays, should be regarded as the important asset of logistics center. However, if the mathematical model focuses on only satisfying constraints related delivery and not considering the cost of trays, it is often to leave the empty trays on the pick-up points when there is not enough space in the track. In this research, it has been proposed to build the mathematical model for optimizing pick-up and delivery plans by extending the general vehicle routing problem of simultaneous delivery and pickup with time windows while considering left-over cost. With the numerical experiments, it has been proved that the proposed model may reduce the total delivery cost. It may be possible to apply the proposed approach to the various logistics business which uses the reusable transporting container like shipping containers, refrigerating containers, trays, and pallets.

We construct a real square system related to a given over-determined real system. We prove that the simple real zeros of the over-determined system are the simple real zeros of the related square system and the real zeros of the two systems are one-to-one correspondence with the constraint that the value of the sum of squares of the polynomials in the over-determined system at the real zeros is identically zero. After certifying the simple real zeros of the related square system with the interval methods, we assert that the certified zero is a local minimum of the sum of squares of the input polynomials. If the value of the sum of the squares of the input polynomials at the certified zero is equal to zero, it is a zero of the input system. As an application, we also consider the heuristic verification of the isolated zeros of polynomial systems and their multiplicity structures. Notice that a complex system with complex zeros can be transformed into a real system with real zeros.

We present a first formal analysis of specific and complete local integration. Complete local integration was previously proposed as a criterion for detecting entities or wholes in distributed dynamical systems. Such entities in turn were conceived to form the basis of a theory of emergence of agents within dynamical systems. Here, we give a more thorough account of the underlying formal measures. The main contribution is the disintegration theorem which reveals a special role of completely locally integrated patterns (what we call ι-entities) within the trajectories they occur in. Apart from proving this theorem we introduce the disintegration hierarchy and its refinement-free version as a way to structure the patterns in a trajectory. Furthermore we construct the least upper bound and provide a candidate for the greatest lower bound of specific local integration. Finally, we calculate the i-entities in small example systems as a first sanity check and find that ι-entities largely fulfil simple expectations.

The use of optical fibers is increasing in modern aircraft because it helps solve challenges of size, weight, communication, and reliability in new aircraft generation. This work describes a video and power transmission system using optical fibers (PoF) for in-flight entertainment (IFE) system application. We present the benefits and the limitations of this application, and we perform two practical experiments to demonstrate their performance. It used off-the-shelf devices in the experiments, such as one 15-W semiconductor laser operating at 808 nm, GaAs photovoltaic converters, optical transmitters and receivers, and video monitors. The power and video signals were transmitted using two 50-m multimode fibers. In addition, we proposed and tested two types of energy transformation units (ETU), which are responsible for supplying electrical energy to the IFE video monitor and the optical fiber receiver.

Background: The oldest old people (≥ 85 years) represent the fastest growing age group in Western populations. Knowledge on early outcomes of acute ischemic stroke (AIS) in very old female patients remains limited. Methods: We assessed gender differences and female-specific clinical data and in-hospital mortality in very old patients with AIS. Acute cerebral infarction was diagnosed in 506 very old female patients from a total of 4,600 acute cerebrovascular infarctions available in an ongoing 24-year hospital stroke data bank. A comparative analysis of vital status at discharge (alive versus dead) was performed in terms of cardiovascular risk factors, clinical data, and early outcomes. Results: The overall in-hospital mortality rate was 20.4%. In multivariate analysis, sudden onset, altered level of consciousness, and neurological, respiratory, cardiological or hemorrhagic complications, and lacunar infarcts appeared to be independent predictors of in-hospital mortality. Conclusions: Female patients ≥85 years with AIS are an unfavorable subgroup of stroke patients with a high risk of early mortality, which may be due to comorbidity, stroke subtype distribution, and higher frequency of medical complications. However, the presence of lacunar infarcts showed a significant protective effect.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

The article analyzes existing materials and structures with quadratic-nonlinear optical properties that can be used to generate a difference frequency in the terahertz and sub-terahertz frequency ranges. The principle of constructing a nonlinear optical-radio converter, based on an optical focon (a focusing cone), is proposed. Based on the assumption that this focon can be implemented from the metal-organic framework (MOF), we propose a technique for modeling its parameters. The mathematical model of the process of propagation and nonlinear interaction of waves inside the focon is based on a simplification of the nonlinear wave equation. Within the framework of the developed model, the following parameters are approximately determined: the 3D gradient of the linear refractive index and the function determining the geometric profile of the focon, which provide a few-mode-based generation of the difference frequency.

In this paper, we give explicit asymptotic formulas for some sums over primes involving generalized alternating hyperharmonic numbers of types I, II and III. Analogous results for numbers with $k$-prime factors will also be considered.

The design flood concept (DF) provides for an essential tool in designing the hydraulic works, in defining the reservoir operation programs and for a reliable flood hazard identification. Under a simplified approach, the maximum discharge and the floods volume are statistically processed to reasonably define the DF. Yet, the integral hydrograph provides additional key temporal and quantitative details of important significance for flood management and particularly for the res-ervoirs operation and associated risks of failures. The procedure presented in this paper (as applied on a set of compatibly shaped hydrographs) involves the following key stages: (i) normalize the floods, (ii) define similar flood shape classes and (iii) evaluate the average dimensionless flood (ADF) for each class. The ADFs are finally transformed into a set of (DF)s. Many statistical distributions approximate acceptably the frequent values of the maximum discharges or the flood volumes, yet displaying a significant spread for medium or rare probabilities of exceedance (PE). This scattering, which can be explained by the epistemic uncertainty, defines an area of uncertainty both for measured and extrapolated values. In considering upper and lower values of the uncertainty in-tervals as limits for maximum discharges and flood volumes, then by combining them compatibly, a set of DFs - as completely defined hydrographs, with different shapes - results for each PE. The herein proposed procedure defines both one peak DF and multi-peaks DF. Subsequently, such DFs do assist water managers in examining and establishing tailored approaches for a variety of input hydrographs. Among the DFs that would correspond to a same PE, the most compact floods arise a special interest, for they are basic in defining the set of safe operation rules for hydraulic structures.

Background: Here, we investigated the inflammaging and physical performance in older adults before and after the COVID-19 pandemic. Methods: Women(n=18) and men(n=7) older were evaluated before the COVID-19 pandemic(PRE), 12 months after the lockdown(POST), and 10 months after resuming exercise training(POS-TR). Physical tests [gait speed(GS) and timed-up-and-go(TUG)]; muscle strength (handgrip-HG), and serum cytokine levels were assessed. Results: The older women showed higher GS and TUG at POST than PRE and POST-TR, besides lower HG at POST-TR than PRE, whereas older men exhibited lower HG at POST and POST-TR than PRE. Both groups presented (1)lower IL-10 and IL-12p70 values in contrast to higher IL-6/IL-10 and IL-8/IL-10 ratios at POST than PRE; (2)higher IL-10 values and lower IL-8/IL-10 ratio at POST-TR than POST; (3)higher IL-12p70/IL-10 ratio at POST-TR than PRE and POST. Particularly older women showed: (4)lower IL-6 values at POST and POST-TR than PRE; (5)lower IL-8 and IL-10 values at POST-TR than POST; (6)and higher TNF-α/IL-10 and IFN-γ/IL-10 ratios at POST than PRE and POST-TR. Significant correlations between the variables were found in both groups. Conclusion: During the COVID-19 pandemic, detraining and resumption of exercise training promoted distinct alterations in physical capacity and inflammaging among older women and older men population.

Road pavement monitoring represents the baseline to the pavement maintenance process. To quickly fix a damaged road, relevant authorities need a high-efficiency methodology that allows them to obtain data describing the current conditions of a network of roads. In urban areas, large-scale monitoring campaigns may be more expensive and not fast enough to describe how pavement degradation has evolved over time. Furthermore, at low speeds, many technologies are inadequate for monitoring the streets. In such a context, employing black box equipped vehicles to perform a routine inspection could be an excellent starting point. However, the vibration-based methodologies used to detect road anomalies are strongly affected by the speed of these vehicles. In this study, a statistical method was to analyze the effects of speed on road pavement conditions at different severity levels through the data recorded by taxi vehicles. Likewise introduced was a process that overcomes the speed effect when considering road surface conditions. The methodology proposed has succeeded in predicting the right damage severity level based on only two recorded parameters: speed and pavement deterioration index.

In this paper, COMSOL Multiphysics software was used to simulate and analyze the process of cleaning oily sludge by high-speed stirring rotor. The physical phenomena such as velocity field, pressure field, heat dissipation and cavitation generated by the rotor during the process of the oily sludge cleaning were analyzed. The results showed that in the process of cleaning the oily sludge by high-speed stirring rotor, the shear force, heat dissipation and pressure increased with the enhance in the rotor speed. Cavitation occurs in the impeller area of the rotor because of the change of pressure, so the cavitation bubbles were formed. Shear force, heat dissipation and cavitation contributed to the separation of oil phase in oily sludge. Meanwhile, the simulation results were verified by experiments.

Understanding the effect of horseshoe-surface combinations on hoof kinematics at gallop is relevant for optimising performance and minimising injury in racehorse-jockey dyads. This intervention study assessed hoof breakover duration in Thoroughbred ex-racehorses from the British Racing School galloping on turf and artificial tracks in four shoeing conditions: barefoot, aluminium-rubber composite (GluShu), aluminium and steel. Shoe-surface combinations were tested in a randomized order and horse-rider pairings (n=14) remained constant. High-speed video cameras (Sony DSC-RX100M5) filmed the hoof-ground interactions at 1000 frames per second. The time taken for a hoof marker wand fixed to the lateral hoof wall to rotate through an angle of 90 degrees during 384 breakover events was quantified using Tracker software. Data were collected for leading and non-leading front and hind limbs, at gallop speeds ranging from 23–56 km h-1. Linear mixed-models assessed whether speed, surface, shoeing condition or any interaction between these parameters (fixed factors) significantly affected breakover duration. Day and horse-rider pair were included as random factors and speed was included as a covariate. The significance threshold was set at p&lt;0.05. For all limbs, breakover times decreased as gallop speed increased (p&lt;0.0005), although a greater relative reduction in breakover duration for hindlimbs was apparent beyond approximately 45 km h-1. Breakover duration was longer on turf compared to the artificial surface (p≤0.04). In the non-leading hindlimb only, breakover duration was affected by shoeing condition (p=0.025) and an interaction between shoeing condition and speed (p=0.023). Future work seeks to relate these results to hoof accelerometer data.

The focus of this research is to improve the performance of dye-sensitized solar cells (DSSC) through the adoption of high-quality FTO thin films and incorporation of graphene with DSSC photoanode to enhance its electrical transport. In this research, nanostructured FTO films were first grown with homemade Streaming Process for Electroless and Electrochemical Deposition technology (SPEED) using Tin (II) chloride dihydrate and ammonium fluoride and other chemical formulations. The FTO structural property was measured by X-ray diffraction (XRD); the films’ optical property was determined with transmittance spectra to curve over the wavelength range of 200-1000 nm measured with a spectrophotometer while scanning electron microscope (SEM) was used to determine the morphological properties of the samples. The electrical transport was evaluated by Hall Effect measurements at room temperature with a four-point probe. The FTO samples with the best structural, optical and electrical properties were employed as electrodes and counter electrodes of DSSC along with titanium dioxide. Thus, effect of graphene on the efficiency of DSSC was investigated. It was shown that a graphene-based DSSC showed an efficiency of 7.98% which is slightly higher than that of DSSC prototype without graphene (6.02%). The higher efficiency obtained with graphene can be credited to the ultrahigh surface area and thermal conductivity of graphene which tend to enhance the charge mobility and photovoltaic performance of DSSC. More research is however required to determine the exact amount of graphene that could achieve optimal DSSC performance. Further studies will also offer an adequate clarification for starting point of the better incorporation of graphene in DSSCs.

Influence of water concentration on the properties of fluorine-doped tin oxide (FTO) thin films was systematically studied in this work. Home made SISOM’s SPEED techniques and its chemical formulation was employed to grow the FTO on quartz substrate. Water concentration in the precursor solution was varied from 0, 0.5, 1.0 and 1.5 mol %. The structural, optical, and electrical properties of the films were studied under these deposition conditions. The results show that the properties of the films varied significantly with water concentration. Scanning electron microscopy (SEM) revealed FTO films whose grain size and uniformity increases significantly with increase in water concentration. The structure of the films was measured by X-ray diffraction (XRD) measurement. It shows polycrystalline films with (110), (101), (200), (211) and (220) orientation; the strength increases as water concentration increases. The optical transmission was determined by UV-Vis spectroscopy at 380–780 nm UV-VIS regions. The optical transmittance varies with water concentration with an average of 84%. The electrical property, measured by Hall Effect revealed n-type semiconductor. The films have the following properties: resistivity, 15 × 10^-4Ω cm; carrier concentration, 18.7 × 10¹⁹ cm^-3 and mobility of 21.86 cm² V^-1 s^-1. The average figure of merit, φ of the FTO film is 1.25. Optimum deposition condition was established after series of experiments and was found to be 1.5% water concentration at 460^oC substrate temperature. The FTO films deposited in this work could be a promising replacement to indium tin oxide (ITO) especially in dye-sensitized solar cells.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

We appeal the science community to review the basic definition of wavelength dependent cosmic red shift. We would like to emphasize the point that, the true cosmic red shift must be defined as the ratio of loss in energy of photon to the energy of photon at galaxy. In terms of wavelength, photon red shift must be defined as the ratio of change in wavelength to the observed wavelength of photon. Considering the recent paper pertaining to cosmic halt authored by Cosmin Andrei, Anna Ijjas, and Paul J. Steinhardt and reviewed by Saul Perlmutter, in this paper we propose a very simple model of the universe having early stage light radius of proton seems to be equal to half the product of reduced Planck’s constant and current speed expansion and current stage quantum halt accompanied by continuous light speed rotation. In this context, representing early cosmic expansion and rotation as an outward spiral, it seems possible to consider Hubble’s law as a representation of current cosmic light speed rotation having no further expansion. To understand the current cosmic halt, we are proposing very simple and very strange atomic and nuclear relations that constitute Hubble parameter and gravitational constant. Qualitatively and quantitatively, gravitational potential energy of proton and electron separated by a distance of root mean square radius of proton. Based on uncertainty condition, it needs further study, observations and analysis. We have extended our analysis towards the microscopic coupling constants. Thus, instead of considering the cosmological variable nature of elementary physical constants, we consider the case of current or nearby cosmic halt by means of considering the equality of current cosmic variable physical constants having similar dimensions of fixed elementary physical constants and their combinations. In this connection, it is very interesting to note that, our estimated cosmic age of (2/H0) is matching with recent estimates proposed by Rajendra P Gupta and published in MNRAS.

Background: In regenerative dentistry the graft material influences the success. It should act as an osteoconductive scaffold, providing a mineral substrate during resorption and inducing the activity of osteoinductive cells capable of producing new bone, platelet growth factors, and cell differentiation factors inducing the differentiation of undifferentiated mesenchymal cells into. Given that dentin shares many biochemical characteristics with bone tissue, it has recently attracted considerable interest as a biomaterial for bone repair. The aim of this study is to compare two grinder types in order to determine the optimal method for producing dentinal particles using a mechanical grinder. Materials and methods: A sample of 40 natural human teeth without restorations, prostheses or root canal treatments was used and divided into two groups subjected to two different grinder speeds (high-speed and low-speed). The high-speed showed a greater dispersion (53.5+-9.89% of the tooth) due to the pulverisation (highly thin granules) of part of the tooth. The low-speed grinder does not pulverize the dentin and the percentage of tooth loss is 9.16+/-2.34%. Conclusion: The low-speed gringer allows to save a major part of the tooth and to have a maximum quantity of graft material but requires more time. Further studies must be promoted to optimise the grinding procedures.

We assessed the use of Evidence-Based Practice (EBP) among pharmacists working in community pharmacies in France, and the factors linked to this practice. During 3 months in 2018 an online survey was sent to over 7,000 active pharmacists, and posted on pharmacist social media sites. The 40-item questionnaire described four clinical cases reflecting typical situations (conventional med-icine and Complementary and Alternative Medicine) encountered daily by community pharma-cists. Multiple-choice responses were proposed and scored according to whether they reflected EBP. A high total score indicated behavior in line with EBP. Univariate and multivariate analyses were used to evaluate factors that might explain adherence to EPB (pharmacy’s characteristics, the pharmacist’s status, mode of continuing education and sources of information). 595 pharmacists completed the questionnaire. The majority relied on pharmaceutical industry and other biased and/or non-evidence-based sources, particularly concerning information on homeopathic products. The consultation of independent reviews, health agency recommendations, and peer-reviewed scientific journals, was associated with evidence-based decisions. In contrast, reliance on phar-maceutical industry documents, personal experience and informal handbooks was linked to lower EBP scores. The level of EBP use by French community pharmacists needs to be improved to ensure that good quality scientifically-based advice is given to customers.

Job satisfaction has a strong impact on the intention to stay which is an important aspect to counter skills shortage in academic medicine. In an interview study combining qualitative and quantitative methods we investigated how the mental representation of working conditions influences job satisfaction and its impact on the intention to stay. In a first study chief physicians participated in interviews about job satisfaction in academic hospitals. Answers were segmented into statements, ordered by topics and rated according to their valence. In a second study assistant physicians (residents) during and after their training period talked about strength, weaknesses and potential improvements of working conditions. Again, answers were segmented, ordered, rated and used to develop a ‘job satisfaction scale’. In a third study, assistant physicians participated in a computer-led repertory grid procedure composing ‘mental maps’ of job satisfaction factors, filled in the job satisfaction scale and rated if they would recommend work and training in their clinic as well as their intention to stay. Comparing the interview results with recommendation rates and intention to stay show that a negative attitude is linked to high workload and poor career perspectives. A positive attitude towards work environment and high intention to stay are linked to sufficient personnel and technical capacities, reliable duty scheduling and fair salaries. The third study using repertory grids showed that the perception of current teamwork and future developments concerning work environment were the main aspects to improve job satisfaction and the intention to stay. The results of the interview studies were used to develop an array of adaptive improvement measure. The results support prior findings that job dissatisfaction is mostly based on generally known “hygiene factors” and whereas job satisfaction is due to individual aspects.

The study of pain requires a balance between subjective methods that rely on self-reports and complementary objective biometrics that ascertain physical signals associated with subjective accounts. There are at present no objective scales that enable the personalized assessment of pain, as most work involving electrophysiology rely on summary statistics from a priori theoretical population assumptions. Along these lines, recent work has provided evidence of differences in pain sensations between participants with Sensory Over Responsivity (SOR) and controls. While these analyses are useful to understand pain across groups, there remains a need to quantify individual differences more precisely in a personalized manner. Here we offer new methods to characterize pain using the moment-by-moment standardized fluctuations in EEG brain activity centrally reflecting the person’s experiencing temperature-based stimulation at the periphery. This type of gross data is often disregarded as noise, yet here we show its utility to characterize the lingering sensation of discomfort raising to the level of pain, individually, for each participant. We show fundamental differences between the SOR group in relation to controls and provide an objective account of pain congruent with the subjective self-reported data. This offers the potential to build a standardized scale useful to profile pain levels in a personalized manner across the general population.

Background: Although rarely indicated, antibiotics are commonly used for acute diarrhoea in China. We conducted a randomized, double blind exploratory clinical trial of loperamide, berberine and turmeric for treatment of acute diarrhoea. Methods: Adults with acute uncomplicated diarrhoea were randomized to 4 groups: (A) loperamide; (B) loperamide and berberine; (C) loperamide and turmeric; (D) loperamide, berberine and turmeric. All participants were given rescue ciprofloxacin for use after 48 hours if symptoms worsened or were unimproved. Primary endpoints were feasibility and ciprofloxacin use during the 2 week follow-up period. Semi-structured interviews were conducted following recruitment. Results: Only 21.5% (278/1295) of patients screened were deemed eligible, and 49% (136/278) of these consented and entered into the final analysis. Most participants had mild symptoms, because most patients with moderate or severe symptoms wanted to be given antibiotics. Follow-up was good (94% at 2 weeks). Only two participants used rescue antibiotics compared to 65% of acute diarrhoea patients in the hospital during the recruitment period. The median symptom duration was: 14 hours in group B (IQR 10-22), 16 hours in group D (IQR 10-22), 18 hours in group A (IQR 10-33), 20 hours in group C (IQR 16-54). Re-consultation rates were low. There were no serious treatment-related adverse events. Most interviewed participants said the treatment was effective. Conclusion: Although recruitment was challenging because of widespread expectations for antibiotics, patients with mild diarrhoea accepted to try an alternative. This therapy requires further evaluation in a fully powered, randomised controlled trial among a broader sample.

Treatment options for sarcopenia are currently limited, primarily relying on two main therapeutic approaches: resistance-based physical activity and dietary interventions. However, details about specific nutrients in the diet or supplementation are unclear. Our objective is to investigate the relationship between nutrient intake and lean mass, function, and strength. Data were derived from the Gothenburg H70 birth cohort study in Sweden, including 719 70-year-olds born in 1944 (54,1 % females). For independent variables, the diet history method (face-to-face interviews) was used to estimate habitual food intake during the preceding three months. Dependent variables were gait speed (muscle performance), hand grip strength (muscle strength) and appendicular lean soft tissue index (ALSTI). Linear regression analyses were performed to analyze the relationship between the dependent variables and each of the covariates. Several nutrients were positively associated with ALSTI, such as polyunsaturated fatty acids (DHA, EPA), selenium, zinc, riboflavin, niacin equivalent, vitamin B12, vitamin D, iron, and protein. After correction for multiple tests, there were no remaining correlations with handgrip and gait speed. Findings of positive correlations for some nutrients with lean mass suggest a role for these nutrients for maintaining muscle volume. These results can be used to inform clinical trials to expand the preventive strategies and treatment options for individuals at risk of muscle loss and sarcopenia.

Advances in technology have introduced remarkable capabilities, particularly in the realm of gathering and accessing vast amounts of data, which has led to the emergence of the "Big Data" era, presenting exciting opportunities to harness the wealth of the generated information. Traffic management centers comprise a stakeholder that can exploit such data towards improving road network operation. This research, explores the utilization of real traffic data, collected by distinct sources on an interurban motorway: static location based aggregate traffic data and probe vehicle data. The first is collected by traffic detectors, while the second involves patrol vehicles’ GNSS data. The traffic quantity analysed is vehicle speed, while specific emphasis has been given on the ap-plication of heatmaps to represent daily traffic patterns and the utilization of k-means clustering. The performed analysis demonstrates the importance of considering spatiotemporal variables as a unified entity when analysing speed in transportation networks. The limitations of using patrol vehicles as estimators of ambient speed, especially in low and heavy traffic conditions, are deline-ated, while the dual purpose of data gathered from these vehicles towards enhancing driving performance and enabling detector maintenance is emphasized. Valuable traffic insights are offered through comprehensive spatiotemporal speed behavior analysis and data combination. The inte-gration of these techniques enhances decision-making for a streamlined and secure transportation system

This pioneering study presents an in-depth biomechanical examination of soccer's diving header, aiming to quantify its impact on ball speed enhancement (BSE) and effective offensive range (EOR). Despite the diving header's widespread acclaim and historical significance, there remains a dearth of scientific scrutiny into its biomechanical intricacies. Employing an innovative research design featuring a static hanging ball at varied offensive distances and heights, the study replicates diverse header scenarios. The results of 3D motion quantification have shown that a physically excellent player (identified through the maximal standing long jump test) could reach an EOR around 2.64 times his body height. Furthermore, the study unveils that proficient players could attain BSE surpassing 9 m/s, signifying the diving header's heightened efficacy compared to traditional heading techniques, which could only result in 4.5 m/s. Correlation analyses unveil noteworthy relationships, highlighting the pivotal role of head speed at impact and the influence of minimizing speed-drop and temporal disparities for amplified effectiveness. Considerations for optimizing diving header execution are introduced, emphasizing the necessity for targeted training programs. Despite acknowledged limitations inherent to its pilot nature, this exploration furnishes foundational knowledge to guide subsequent research and practical applications, providing valuable insights into soccer training and skill development through a biomechanical lens.

This paper shows the development of a numerical analysis model, which enables the calculation of the cargo transport capacity of a vehicle that circulates through a vacuum tube at high speed, whose effectiveness in transport is analyzed. The simulated transportation system is based on vehicles moving in vacuum tubes at high speed, a concept commonly known as Hyperloop, but assuming the vehicles for cargo containers. For the specific vehicle proposed, which does not include a compressor and levitates on magnets, the system formed by the vehicle and the vacuum tube has been conceptually developed, establishing the corresponding mathematical relationships that define its behavior. To properly model the performance of this transport system, it has been necessary to establish the relationships between the design variables and the associated constraints, such as the Kantrowitz limit, aerodynamics, transport, energy consumption, etc. Once the model was built and validated, it was used to analyze the effects of the variation of the number of containers, the operating speed and the tube length, considering the total and specific consumption of energy. Once the most efficient configuration was found regarding energy consumption and transport effectiveness, the complete system was calculated. The results obtained constitute a first approximation for the pre-design of this transport system and the built model allows different alternatives to be compared according to the design variables.

G4v is a four-vector theory of gravitation proposed by Mead (2015, 2023a,b) which reinterprets several major results commonly celebrated for the tensor-based approach of General Relativity (GR). Here, we show that G4v obeys the correspondence principle, an important test of any relativistic theory. We derive the non-relativistic Lagrangian and Energy expressions at the limit of low speeds and potentials, complete with the correct terms for potential energy (something traditional Special Relativity is incapable of achieving). G4v could represent a new interpretation of the gravitational field with essentially the same mathematics as electromagnetism (Mead 2023a). It is also possible to interpret G4v as a very interesting (and useful) approximation of the Einstein field equations (Mead 2023b).

The quantile estimation of extreme wind speed is needed in various environmental fields such as climatology, design of structures, renewable energy sources and agricultural operations. These calculations are crucial for the coding of wind speed. In this study, the required wind speed series of 16 stations in Khyber Pakhtunkhwa, Pakistan, was obtained from the NASA official website and measured in meters per second (m/s) at a 10-meter distance. A Regional Frequency Analysis of 16 AMWS stations was performed using L-moments. The quantile estimates of extreme wind speed are needed for various areas of interest using Regional Frequency Analysis (RFA) and extreme value theory. These calculations are crucial for the coding of wind speed. The data was taken from the NASA official website at a 10-meter distance and measured in meter per second (m/s). A Regional Frequency Analysis of AMWS using L-moments is performed utilizing wind speed data from sixteen sites (16) in Pakistan's Khyber Pakhtunkhwa province. There are no sites that are found to be discordant. The wards method is used to construct a homogenous region and make two homogenous regions from 16 sites. The heterogeneity test justifies that both clusters are homogeneous. The most appropriate probability distribution from the Generalized Normal (GNO), Generalized Logistic (GLO), Pearson Type-3 (P3), Generalized Pareto (GPA), and Generalized Extreme Value (GEV) distributions are chosen to calculate regional quantiles. According to the L-moments diagram and Z statistics, GEV for Cluster- Ι and GLO for Cluster- ΙΙ are the best suggestions from the others. Both clusters’ robustness is measured utilizing Relative Bias (RB) and Relative Root Mean Square Error (RRMSE). Overall, GEV distribution is fit for cluster-Ι, and the GLO distribution is fit for cluster-ΙΙ. Utilizing the site mean and median as index parameters, we can also find at-site quantiles from regional quantiles. The study’s quantile estimates can be employed in codified structural designs with policy consequences.

The fault diagnosis of the gearbox is primarily based on the analysis of the harmonic response. However, the generation mechanism of the harmonic response of the gear pair is still not distinctly explained in a healthy gearbox. Therefore, this paper is dedicated to establishing a dynamic model of the gearbox for this issue. In this model, the contact force of the bearing and the meshing stiffness of the gear pair are determined by the Hertz theory and the potential energy method, then the shaft motion is used as the connection to establish the coupling relationship between the gear pair and the bearing. After this dynamic model is confirmed by experiments and existing models, the coupling relationship inside the gearbox and the harmonic response of the gear pair are studied using this model. The result demonstrates that a closed control loop is formed due to the vibration transmission between the gear pair, the bearing and the shaft, and there is a strong coupled vibration between the gear pair and the bearing in the gearbox. Due to the generation of the center distance error, misalignment angle and disorganized meshing process of the gear pair, the meshing stiffness is altered, which excites the harmonic response of the gear pair. When the speed of the gearbox is increased, although the vibration amplitude of the gearbox is increased, the system predominantly vibrates at the fundamental frequency, and the harmonic of the gear pair is also shifted to the low frequency band.

As rotary machines have become more complicated, balancing processes have been classified as a vital step in condition monitoring to ensure machines operate both reliably and safely. This is especially important for flexible machines which normally work at rotations speeds above critical limits. Imbalance is a common problem in flexible rotating machinery that can lead to extreme vibration and noise levels. This is one of the major reasons for studying various balancing methods applied to the vibration response of rotating machines. Recently, the relation between acoustic and vibration response during a rotary machine balancing process based on the Four-Run method has been presented for constant speed machines. This method cannot be applied to machines in start-up or shut-off. Hence, by considering the acoustic and vibration responses of a machine between its critical speeds, this research presents a new innovative speed-variant balancing method based on the original Four-Run method, named as "Peak to Peak for Critical Speeds (PPCS)". The proposed method consists of two major types of application: the first is in the Run-up of the machine and the second is in Shut-down. Experimental laboratory results show that the PPCS method can be implemented for speed-variant and flexible rotary machines during run-up or shut-down transient processes based on acoustic and vibration measurements. As a phase-less and a contactless method, the PPCS can be employed as an innovative and readily available method for condition monitoring in the future.

The overarching purpose of this review was to highlight the utility of different aerobic field tests in terms of the parameters they provide, with a specific focus on shuttle running and all-out testing. Various field tests are discussed in detail and are categorised according to linear continuous running tests (e.g. 12-minute Cooper Test, University of Montreal Track Test [UMTT], 1200/1600 m time trials, 3-minute all-out test for running [3MT]), intermittent shuttle running tests (e.g. yo-yo inter-mittent recovery test level 1 [YYIR1], 30-15 intermittent fitness test [IFT], and the intermittent all-out shuttle test [IAOST]), and continuous shuttle running tests (e.g. 1.2 km shuttle run test [1.2SRT], maximal multi-stage 20-m shuttle test [MSR], 25-m, 30 m and 50-m 3-minute all-out shuttle test [AOST]). Readers will be guided through the theoretical and practical underpinnings of the 3MT methodology, where the all-out testing methodology is stationed within the testing paradigm, and how to practically implement and interpret the results thereof.

In this era of technology, programming has become more significant than ever before. Python and C++ are both widely used programming languages. Python, the most popular programming language in today’s world, is a high-level object-oriented language whereas C++, the language behind most operating systems, is a low-level object-oriented language. In this paper, we present a comparative study of Python and C++. This paper discusses the introduction to these languages, their memory management techniques, and the reasons behind their program execution speed. Furthermore, we analyzed the execution time and memory used by multiple algorithms in both the languages with best, average, and worst cases. They are also compared with respect to the benefits and issues related to them. Results indicate that C++ is faster than Python in execution speed but Python serves as a better language for beginners due to its simplicity. Moreover, for the best results, the language should be selected according to the type of project.

Pore Forming Toxins (PFTs), formed mainly by virulence factors of bacteria, belongs to Pore Forming Protein (PFP) family. Secreted as soluble monomers, they bind specific targets in membranes where their oligomerization and insertion place. Lysenin, a member of the PFTs, forms and oligomer after sphingomyelin binding, the so-called prepore, which become inserted forming a pore after a conformational change triggered by a pH decrease. In crowded conditions, oligomers tends to stay in prepore form because the prepore-to-pore transition is sterically blocked. In this study, we investigate the effect of calcium ions in those crowded conditions, finding that calcium act as a trigger for lysenin insertion. We localize the residues responsible for calcium sensitivity in a small α-helix. Our results are not only one of the few complete structural descriptions of prepore-to-pore transitions but the very first that involves a calcium triggering mechanism. The presence of glutamic or aspartic acids in the insertion domains could be an indication that calcium may be a general trigger for PFTs and more generally PFP.

Cognitive impairment and sarcopenia may share common risk factors and pathophysiological pathways. This study was performed to examine the association between impairments in specific cognitive domains and sarcopenia (and its defining components) in a large group of community-dwelling older adults. Cross-sectional analysis was performed on the baseline data of 3,014 adults aged 70–84 years enrolled in the Korean Frailty and Aging Cohort Study (KFACS). The final analysis included 1,887 adults underwent dual-energy X-ray absorptiometry and cognitive function assessments. Those with disability in activities of daily living, dementia, severe cognitive impairment, Parkinson’s disease, musculoskeletal complaints, neurological disorders, or who were illiterate were excluded. Cognitive function was assessed using the Korean version of the Consortium to Establish a Registry for Alzheimer’s Disease Assessment Packet, the Frontal Assessment Battery. For sarcopenia, we used the diagnostic criteria of the Asian Working Group for Sarcopenia. The prevalence of sarcopenia was 9.6% for men and 7.6% for women. Sarcopenia (odds ratio [OR] 1.76, 95% confidence interval [CI] 1.04–2.99) and slow gait speed (OR 2.58, 95% CI 1.34–4.99) were associated with cognitive impairment in men. Only slow gait speed (OR 1.88, 95% CI 1.05–3.36) was associated with cognitive impairment in women. Sarcopenia is associated with cognitive impairment mainly due to slow gait speed. Our results suggested that cognitive impairment domains, such as processing speed and executive function, are associated with sarcopenia-related slow gait speed.