The combustion of fuel oil releases sulfur compounds, which react to form sulfur oxides that are harmful to the environment and pose a threat to human health. To mitigate these negative effects, it is crucial to pretreat fuel oil through desulfurization processes. One promising approach involves the use of deep eutectic solvents (DESs), carbon nanotubes (CNTs), and their composites (DESs/CNTs) to effectively reduce sulfur content in fuel oil.However, the conventional methods of DES-based extraction desulfurization and CNT-based adsorption desulfurization suffer from low desulfurization rates. Additionally, the composite material DESs/CNTs is in a semi-solidified form, resulting in high viscosity, complex operation procedures, and increased waste and environmental pollution. To address these challenges, this study focused on the preparation of CNTs/PEG-PVA hydrogel. This hydrogel not only maintains the high desulfurization rate observed in the DESs/CNTs composite material but also possesses several advantages. Firstly, it is convenient to use, offering ease of handling and application. Secondly, it is biodegradable, meaning it can break down naturally over time, reducing its impact on the environment. Lastly, the hydrogel is reusable, allowing for repeated use, thereby minimizing material waste. The desulfurization rate achieved with the CNTs/PEG-PVA hydrogel is remarkably high, reaching up to 99.8%. Moreover, the material utilization rate is close to 100%, meaning that almost all of the hydrogel is utilized in the desulfurization process, reducing unnecessary material consumption. In summary, the innovative CNTs/PEG-PVA hydrogel presents a highly efficient and environmentally friendly solution for desulfurization in fuel oil. Its superior desulfurization rate, alongside its convenience, biodegradability, and reusability, positions it as a promising alternative that not only ensures effective desulfurization but also contributes to sustainable practices in the energy industry.

The gold(I) N-heterocyclic carbene (NHC) complexes, containing a combination of 1,3-bis(2,6-diisopropylphenyl)imidazol-2-ylidene (iPr) and the corresponding 7-azaindole derivative (HL1-4), were prepared and structurally characterized. The complexes of the composition of [Au(iPr)(HLn)], where n = 1–4 for 5-fluoro-7-azaindole (1), 5-bromo-7-azaindole (2), 3-chloro-7-azaindole (3) and 3-iodo-7-azaindole (4), were further evaluated for their in vitro anti-cancer and anti-inflammatory activities. The results showed that complexes (1–4) behave as considerably cytotoxic against human ovarian cancer cell line A2780 (with IC50 = 4–9 mircoM) and cisplatin-resistant cell line A2780R (with IC50 = 5–8 microM, except for 2 with IC50 > 25 microM), providing significantly higher cytotoxicity than anticancer drug cisplatin. Moreover, they also revealed a relatively good selectivity over normal cells (MRC-5), with the values of selectivity index, SI > 2.5. The complex 4 was further studied for its cellular effects in A2780 cells by cell cycle analysis, induction of apoptosis, intracellular ROS production, activation of caspases 3/7 and disruption of mitochondrial membrane potential. The ability of complexes (1–4) to influence the activity of pro-inflammatory transcription factor NF-κB and secretion of TNF-α were evaluated, showing that complex 4 reveals comparable effects as the inflammatory drug Auranofin.

This study developed Makgeolli (Korean traditional alcoholic beverage) by adding raw 20% Codium fragile (Cf), a green seaweed, to a mixed base consisting of rice and oats (1:1 ratio) (COM) and analyzed its quality characteristics and antioxidant activity. The rice based Makgeolli supplemented with raw 20% Cf was designated as control (CRM). The physicochemical (pH, acidity), microbiological (yeast, lactic acid bacteria), antioxidant (DPPH, ABTS), and sensory properties (7-henodonic scale) of CRM and COM were investigated during 7 days of fermentation. The pH/acidity levels of CRM and COM reached 3.66/0.68 and 3.69/0.95 after 7 days of fermentation, respectively. Compared to CRM, COM had lower alcohol and sugar contents (P < 0.05) (CRM: 14.5%/9.8 Brix, COM: 11.2%/7.4 Brix). However, COM contained more yeast and lactic acid bacteria (P < 0.05) (CRM: 1.30/4.28 log, COM: 6.04/6.09 log) compared to CRM. The antioxidant activity of DPPH/ABTS (P < 0.05) in COM was approximately 1.5 times that of CRM (CRM: 40.00/51.57%, COM: 56.76/70.91%). In addition, COM had an excellent sensory preference score (P < 0.05) due to its overall fresh flavor and savory taste (CRM: 4.93, COM: 6.06). Therefore, COM was shown to be Makgeolli with enhanced antioxidant function, with yeast and lactic acid bacteria, and improved flavor, suggesting the possibility of commercializing this Makgeolli.

This study investigated the potential of electrospun collagen/Hyaluronic Acid nanofibers in biomedicine and skincare. Needleless electrospinning technology employed in the production process resulted in nanofibers with consistent fiber diameters and improved mechanical properties. The composite nanofibers demonstrated impressive tensile strength and elongation capabilities, indicating a favorable interaction between collagen and HA. Cellular assays revealed that the collagen/HA scaffolds facilitated superior cell adhesion and proliferation compared to the control scaffolds, indicating their biocompatibility and potential for tissue engineering. This biomaterial offers an environment-friendly alternative to conventional skincare products by eliminating the need for preservatives and reducing waste. Although the initial costs are high, the long-term benefits of material durability and active ingredient efficacy provide a compelling case for industrial adoption. Our findings suggest that collagen/HA nanofibers have the potential to be next-generation materials for regenerative medicine and skincare, and further research is needed to optimize their production and assess the economic feasibility of skincare and tissue engineering applications.

The Sm3+/Gd3+ co-doped glasses in the B2O3–GeO2–PbO and B2O3–GeO2–Bi2O3 systems have been synthesized in the composition range of 40B2O3–40GeO2–(15-17)PbO(Bi2O3)–(3-2)Sm2O3–(2-1)Gd2O3 and 42.5B2O3–42.5GeO2–(11.25-12.75)PbO(Bi2O3)–(2.25-1.5)Sm2O3–(1.5-0.075)Gd2O3. The physical, structural, and spectral properties of the produced glasses have been studied. The fabricated glass samples demonstrated changes in temperature-sensitive luminescence parameters in 298-673 K temperature range. We found out several photoluminescence bands attributed with transitions from different Stark sublevels. By using a combination of two temperature sensitive and one non-sensitive transitions we calculated fluorescence intensities ratio (FIR). This procedure made it possible to increase the sensitivity of luminescence thermometry in several times. Such method could be very useful for the luminescent thermometry materials based on Ln3+ ions with multiplied f-f transitions.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

Reflux esophagitis, a treatment for gastric ulcers known as Ilaprazole (Ila), is not stable during storage and handling at room temperature, requiring storage at 5 degrees celsius. In this study, to address these issues with Ila, coformers rich in oxygen (O) and hydroxyl (OH) groups capable of forming hydrogen bonds with were selected. These coformers included Xylitol (Xyl), Meglumine (Meg), Nicotinic acid (Nic), L-Aspartic acid (Asp), and L-Glutamic acid (Glu). A 1:1 physical mixture of Ila and each coformer was prepared, and the potential for cocrystal for-mation was predicted using differential scanning calorimetry (DSC) screening. The results indi-cated the potential for cocrystal formation in the Ila/Xyl physical mixture. Subsequently, Ila and Xyl were mixed in ethyl acetate (EA) in a 1:1 ratio, and after 28 hours of slurry, the formation of Ila/Xyl cocrystal was confirmed through solid-state CP/MAS 13C NMR spectrum analysis, showing intermolecular hydrogen bonding and conformational changes. Furthermore, the 1:1 ratio of Ila/Xyl cocrystal was confirmed through solution-state NMR (1H, 13C, and 2D) molecular structure analysis. To assess the stability of Ila/Xyl cocrystal at room temperature, it was stored and com-pared with Ila at 25±2°C and relative humidity (RH) of 65±5% over three months. The results showed that the purity of Ila/Xyl cocrystal remained at 99.8% from the initial purity of 99.75% over the three months, while Ila was predicted to decrease from an initial 99.8% purity to 90% after three months. Additionally, at 25±2°C and RH 65±5%, a specific impurity B in Ila/Xyl cocrystal was observed to be 0.03% over three months, whereas Ila was predicted to increase from an initial 0.032% to 2.28% after three months. To evaluate the dissolution rate of Ila/Xyl cocrystal, a formulation was prepared and compared with Ila at pH 10, with a dosage equivalent to 10mg of Ila. The results showed that Ila/Xyl cocrystal reached 55% within 15 minutes and 100% within 45 minutes, while Ila was predicted to reach 32% at 15 minutes and 100% only after 60 minutes. However, overall, the Ila/Xyl cocrystal showed results equivalent to or exceeding the dissolution rate of Ila. Therefore, it is predicted that the Ila/Xyl cocrystal will maximize its effectiveness as a more convenient crystal structure for formulation development, allowing storage and preservation at room temperature without the need for the problematic 5°C refrigeration during ambient con-ditions and storage, addressing the issues associated with Ila.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

This review provides an extensive overview of the developments in the field of polymer science, focusing on the solid-state modification (SSM) of thermoplastic materials. The background of the study places thermoplastics within the context of their increased use over the past century, highlighting their versatility in various applications and the associated environmental and health concerns due to certain additives. The methods section delves into the specifics of SSM, a technique that involves the incorporation of monomers or oligomers into the amorphous phase of polymers through multiple exchange reactions, distinguishing it from traditional melt polymer modification methods. The results section outlines the unique aspects of SSM and its increasing recognition for its potential to enhance material performance in areas such as catalysts and composites. It also discusses the application of SSM in modifying different thermoplastic polymers, highlighting various studies demonstrating the method's effectiveness in altering polymer properties. Finally, this work emphasizes SSM's importance in environmental sustainability and its potential in the recycling and upcycling of plastic materials. It acknowledges the challenges and future perspectives in the field, particularly regarding the scalability of SSM techniques for industrial applications and their role in advancing a circular economy in the polymer industry.

SmCo5 constitutes one of the strongest class of permanent magnets, which exhibit enormous uniaxial magnetocrystalline anisotropy energy and have a high Curie temperature. However, the performance of SmCo5 permanent magnets is hindered by a limited energy product and relatively high supply risk. Sm is a moderately expensive element among its group, and Co is a material more expensive than Fe, making SmCo5 magnets the most expensive class of permanent magnets. Subsequently, the need for new materials, with less content in critical and thus expensive resources, is obvious. A promising path of producing new compounds that meet these requirements is the chemically modification of established materials used in PM towards the reduction of expensive resources, for example reducing Co content with transition metals (like Fe, Ni) or using as substitutes raw rare earth materials with abundance greater than their demand, like Ce and La. Important instrument to achieve these goals are theoretical calculations, like Ab-initio methods, and especially DFT based calculations in predicting the possible stable RE-TM intermetallic compounds and their magnetic properties. This review aims to present the progress of recent years in the production of improved SmCo5 type magnets.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

In this study, various diamine monomers were used to synthesize aramid polymer films via a low-temperature solution condensation reaction with diacid chloride. For diamines with relatively high basicity, the reaction system became opaque because amine salt formation inhibited polymer synthesis. Meanwhile, low-basicity diamines with strong electron-withdrawing groups, such as CF3 and sulfone, were smoothly polymerized without amine salt formation to provide highly viscous solutions. The acid byproduct HCl generated during polymerization was removed by adding propylene oxide to the reaction vessel and converting the acid into highly volatile inert substances. The resulting solutions were used as varnishes without any additional purification, and polymer films with an excellent appearance were easily obtained through a conventional casting and convection drying process. The films neither tore nor broke when pulled or bent by hand; furthermore, even when heated up to 400°C, they did not decompose or melt. Moreover, polymers prepared from 2,2-bis (trifluoromethyl) benzidine (TFMB) and bis (4-aminophenyl) sulfone (pAPS) did not exhibit glass transition until decomposition. The prepared polymer films showed a high elastic modulus of more than 4.1 GPa and a high tensile strength of more than 52 MPa. In particular, TFMB-, pAPS-, and 2,2-bis (4-aminophenyl) hexafluoropropane-based polymer films were colorless and transparent, with very high light transmittances of 95%, 96%, and 91%, respectively, at 420 nm and low yellow indexes of 2.4, 1.9, and 4.3, respectively.

In this work, electrochemical deposition (galvanostatic and potentiostatic) techniques were used to obtain of new composite polymer: 3-methylpyrrole - sodium dodecyl sulfate/poly 2-methythiophene (P3MPY-SDS/P2MT) coatings on cobalt -based alloy sample for anticorrosion protection. The sodium dodecyl sulfate as a dopant ion used in electropolymerization practice can have a relevant effect at the anticorrosion protection of the composite polymer layer by blocking the entry of aggressive ions. The cobalt -based alloy substrate had an important influence on the electrochemical performance of the composite coating and this together with the presence of the polymeric layer was achieved by simultaneously formation of a complex oxides film and polymeric layers. The polymeric coatings were analyzed by cyclic voltammetry, Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion protection of P3MPY-SDS/P2MT coated cobalt based alloy has been explored by potentiostatic and potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) procedures in1 M HCl medium. The corrosion establishment of P3MPY-SDS/P2MT covered cobalt based alloy was observed to be ~10 times less than that uncoated specimen and the effectiveness of these composite layers of this coating is above than 90%. The superior efficacy is achieved by the electrochemical polymerization of P3MPY-SDS/P2MT obtained at 0.5 mA/cm2 and 1mA/cm2 current densities and at 0.9V and 1.0V potential applied and in molar ratio 5:1. Corrosion tests result indicated that P3MPY-SDS/P2MT coatings provide good corrosion protection of cobalt -based alloy in aggressive environments.

Liposome vesicle is an ideal carrier for carbon nanotube (CNT) to serve as the water channel that allows the fast transport of water molecules, and thus enhancing the membrane permeability. However, low quantity of the inserted CNT in the liposome vesicle is an important factor that limited further improvement of the membrane flux. In present study, positively charged lipids (2,3-dioleoyloxy-propyl)-trimethylammonium-chloride (DOTAP) was introduced to the 1,2-dioleoyl-sn-glycero-3-phosphoethanolamineon (DOPE) liposome vesicles to tailor the vesicle charge, so as to evaluate the effect of positively charged DOTAP on the insertion of CNT into liposomes and separation performance of thin-film nanocomposite (TFN) membranes. The results showed that addition of DOTAP induced more quantity of CNT inserted into the liposome vesicles, since the shrinkage rate (k) and permeability (Pf) of liposome vesicles present obvious increase with increased content of DOTAP in the liposome vesicles. Besides, it contributed to 252.3% higher water flux for TFN membranes containing DOPE/DOTAP2:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 2:1) than TFC membranes. More important, it presented 106.7% higher water flux for TFN membranes containing DOPE/DOTAP4:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 4:1), which was originated from the more water channels that the CNT provided in the liposome vesicles. In all, positively charged DOTAP effectively tailored the vesicle charge, which provided a better carrier for the insertion of more quantity of CNT, and contributed to higher permeability of TFN membranes.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

Global food waste has a huge impact on the environment, as it is a source of greenhouse gas (GHG) emissions and wasted natural resources. Across the world, over 30% of food is lost or wasted each year. Aside from this, food industry, as well, is one of the biggest sources of agro-industrial waste and by-products, which can be valorized and used for different purposes. Such waste is a good source of bioactive organic compounds which can be extracted without al-tering their properties, where deep eutectic solvents (DESs) can serve as green solvents and excel-lent replacement for volatile organic solvents. Isolated compounds can be used in innovative food production, chemical production, cosmetics and other industries. DESs have attracted extraordi-nary attention due to their advantages such as environmental friendliness, availability and easy preparation, easy handling and utilization of non-toxic components for their formation. Due to those properties, they are a greener alternative to classic organic solvents for many processes, in-cluding extractions. In this paper, we review the utilization of deep eutectic solvents as potential green media for the extraction of organic compounds such as polyphenols, carbohydrates, pro-teins, alkaloids from by-products of the food industry and agro-industrial-waste.

Synthesis of natural products with complicated architecture often requires segments having the functional groups that can be structurally transformed with the desired stereogenic centers. Bicyclic ?-lactones have a great potential for a suitable segment for natural product synthesis. However, the stereoselective construction of such functionalized bicyclic ?-lactones is not as straightforward as one might expect. On the other hand, the Lewis acid template-mediated Diels-Alder reaction is one of the most powerful and versatile methods for providing bicyclic ?-lactones with high regioselectivity and stereoselectivity. In this reaction, the Lewis acid template activates the dienophile as well as linking the diene and dienophile by a temporary tether. Therefore, Diels-Alder reaction smoothly proceeds in a stereocontrolled manner, allowing a simple access to bicyclic ?-lactone as a valuable building block for the synthesis of complicated natural products. In this review, some highlights of the Lewis acid-mediated Diels-Alder reaction, along with its application to the synthesis of biologically active compounds are discussed.

Tungsten and its alloys are considered as a key component in high temperature environment. Self-passivating W-Si-xY alloys with different Y contents made from the powders milled for different times were prepared by mechanical alloying (MA) and spark plasma sintering (SPS). Their microstructures and oxidation resistance were investigated. It is found that the oxidation resistance of the alloys with low Y contents (0Y and 2Y) made from 20 h-milled powders is worse than that of the alloys made from 4 h-milled powders. It is because the protective WO3/SiO2 composite layer is discontinuous. While the alloys with high Y contents (4Y and 6Y) made from 4 h and 20 h-milled powders show good oxidation resistance. Even, the thickness of the oxide layer of the alloys with 4Y and 6Y made from 20 h-milled powders after oxidation at 1000 ℃ for 2 h is 84.0 μm and 70.7 μm, less than that made from 4 h-milled powders. This is due to the size and distribution of W5Si3, Y2Si2O7 aggregates and W-Y-O melt. The synergistic effects of Y contents and milling time on the microstructures and oxidation resistance of the alloys are revealed.

This comprehensive review is devoted to an under-exploited family of phenolic compounds, the coumarins, and the most relevant strands in which they are involved in some spirit beverages – wine spirit, brandy, whiskey, sugar cane spirits (rum and cachaça) and grape marc spirit – with great importance worldwide in terms of production, trade and consumption. It gathers the key discoveries on the topic considering the production process of each spirit beverage, the related sources of coumarins (different kinds of wood used in the ageing stage) along with the factors that govern them and can influence the sensory properties of the aged beverages. An overview of the analytical methods available for their identification/quantification is also included, as well as the corresponding trends for the advancement of knowledge in this field. Moreover, the remarkable role of coumarins as nutraceuticals, their importance as chemical markers for authenticity purposes, and their relationship with food safety of these spirit beverages are also addressed, highlighting the current gaps and issues, and providing clues for future research.

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

In the northern Patagonian region of Argentina, there exist some of the largest bentonite deposits. Four bentonite samples (B1, B2, B3, and B4) from two deposits were thoroughly characterized and evaluated as potential adsorbents of anthocyanins extracted from red cabbage. Anthocyanins (ACy) are natural colourants obtained from fruits and plants and have shown excellent antioxidant properties that have promising applications in health. The adsorption of ACy onto bentonites enhances their stability relative to that observed in aqueous solutions. Material characterization showed that three of the samples are sodium bentonites (Na-bentonites: B2, B3, and B4), while the fourth exhibits a large quantity of magnesium and calcium in its interlayer, classifying it as a Mg-Ca-Na-bentonite (B1). Na-bentonites demonstrated higher ACy adsorption capacities, occurring through cation exchange while Mg-Ca-Na-bentonite adsorption occurs by another kind of interaction and a cooperative adsorption mechanism, resulting in the lowest ACy adsorption. The highest adsorption capacity was for B3, characterized by the highest smectite content, cation exchange capacity, and proportion of monovalent cations in its interlayer. Under the conditions studied, sodium smectites proved to be capable of retaining red cabbage ACy, there by introducing a novel avenue for potential applications of regional materials with potential implications for health-related uses.

Matrix asphalt material has poor road performance, which is improved by adding polymer modified agents. The original asphalt material experiment research has a certain limitation in that it cannot truly expose the mechanism and influence of modifiers on asphalt materials. To explore the gain effect of the modified agent on the asphalt material's road performance, the molecular dynamic simulation technology is used to explain its mechanism in the micro dimension. The three parameters of the free volume score, radial distribution function and average directional shift diffusion coefficient are analysed to improve the performance of the modifier on asphalt material, an exploration of the microdimension shows that the amount of SBS modifiers is 6% and the amount of rubber modified asphalt material is 22%. The improvement of materials is better than that of rubber modifiers.

Births occurring before thirty-seven weeks of gestation are referred to as preterm births (PTBs), which is the primary cause of neonatal mortality and long-term disabilities. The unknown mechanism behind PTB makes diagnosis difficult, yet early detection is necessary for controlling and averting related consequences. The primary focus of this work is to provide an overview of the known risk factors associated with preterm labor and the conventional and advanced procedures for early detection of PTB, including multi-omics and artificial intelligence (AI)/machine learning (ML)-based approaches. It also discusses the principles of detecting various proteomic biomarkers based on lateral flow immunoassay and microfluidic chips, along with the commercially available point-of-care testing (POCT) devices and associated challenges. After briefing the therapeutic and preventive measures of PTB, the review summarizes with an outlook.

Milled MgH2, NaAlH4, MgH2–10NaAlH4, MgH2–30NaAlH4, MgH2–50NaAlH4, and MgH2–2Ni-10NaAlH4 samples were prepared by milling in hydrogen atmosphere (reactive mechanical milling, RMM). Decomposition temperatures of milled MgH2, NaAlH4, MgH2–10NaAlH4, and MgH2–30NaAlH4 were examined in a Sieverts-type hydrogen-absorption and release apparatus, in which the hydrogen pressures were kept constant during hydrogen absorption or release. As the content of NaAlH4 in the sample increased, the temperature at the highest peak in the ratio of increase in Hr to increase in T, dHr/dT, versus T curve decreased. The higher content of NaAlH4 is believed to have made effects of reactive mechanical milling stronger. Effects of the NaAlH4 content on the temperatures of intermediate reactions were studied for MgH2 – NaAlH4 composites. Phase formation in the cycled MgH2–50NaAlH4 were investigated. The hydrogen-storage properties of MgH2–30NaAlH4 were compared with those of Mg-based alloys in which oxide, halides, or fluoride was added.

Bismaleimide (BMI) is a high-performance thermosetting resin widely used in the aerospace, automotive, and mechanical and electronics industries due to its chemical and mechanical stability. It also has the capability of being used as an ink in polyjets used for 3D printing evident from thinner mellamide FTIR bands and faster curing rates as observed from TGA-DSC studies.

The perovskite solar cells (PSCs) have been significantly improved by utilizing inorganic hole transporting layer (HTL), such as nickel oxide. Despite the promising properties, there are still limitations due to defects. Recently, research on self-assembled monolayers (SAM) is being actively conducted, which show promise in reducing defects and enhancing device performance. In this study, we successfully engineered a p-i-n perovskite solar cell structure utilizing HC-A1 and HC-A4 molecules. These SAM molecules were found to enhance the grain morphology and uniformity of the perovskite film, which are critical factors in determining optical properties and device performance. Notably, HC-A4 demonstrated superior performance due to its distinct hydrophilic properties with a contact angle of 50.3°, attributable to its unique functional groups. Overall, the HC-A4 applied film exhibited efficient carrier extraction properties, attaining a carrier lifetime of 117.33 ns. Furthermore, HC-A4 contributed the superior device performance with its favorable band alignment, achieving the highest device efficiency of 20%.

A new biodegradable paper-based film is a hot research topic in the development of green agriculture. In this paper, a black paper base film coated with cooked tung oil with excellent mechanical properties, hydrophobic surface, high heat transfer and strong weather resistance was prepared by spraying high pigment carbon black solution on the surface of base paper. The results showed that the surface solidified oil film with rough structure was made by the brush coating process of cooked tung oil, and the base film of black paper was given hydrophobic structure, and the contact angle reached 98.9 °. Cooked tung oil permeates into the inside of the paper base, and after curing, it forms a multi-dimensional network film structure. The maximum tensile stress of the black paper base film is about 123% higher than that of the original paper base film. The coloring of carbon black makes the black paper base film have heat conduction effect, and the average heat transfer rate reaches 15.12 °C/s. Cooked tung oil is combined with the paper-based fiber high-toughness layer to form a stable system. The existence of the cured film improves the basic mechanics and hydrophobicity, and the resistance to ultraviolet radiation and hot air is greatly improved. This study provides a feasible scheme for the application of a black paper base film coated with cooked tung oil.

The detection and analysis of small molecules, typically defined as molecules under 1000 Da, is of growing interest ranging from the development of small molecule drugs and inhibitors to the sensing of toxins and biomarkers. However, due to challenges such as their small size and low mass, many biosensing technologies struggle to have the sensitivity and selectivity for the detection of small molecules. Notably, their small size limits the usage of labeled techniques that can change the properties of small molecule analytes. Furthermore, the capability of real-time detection is highly desired for small molecule biosensors’ application in diagnostics or screening. This review highlights recent advances in label-free real-time biosensing technologies utilizing different types of transducers to meet the growing demand for small molecule detection.

This research presents a comprehensive bibliometric and sentiment analysis of nanocomposite literature from 1990 to 2024. Employing cutting-edge computational methods, the study delves deep into the progression of microstructural characterization, electrical properties, and mechanical behaviors of nanocomposites. The analysis utilizes advanced Boolean search strategies from the Scopus database, ensuring a thorough extraction of thematic content. The results explore various themes and insights, shedding light on trends evident in the Scopus database, particularly the prominence of research on nanocomposite microstructure, electrical attributes, and mechanical performance. The paper also offers textual analytics and bibliometric data, showcasing critical collaborative efforts and influential studies. Significant discoveries encompass the evolution of research language, shifts in thematic focus, and global contributions, providing a comprehensive perspective on the current landscape of nanocomposite research and its dynamic evolution. Moving forward, the "State-of-the-Art and Gaps Extracted from Results and Discussions" section of the paper delves into the most recent advancements in nanocomposite research. It delves into various types of nanocomposites, with a particular emphasis on their microstructural characteristics, electrical properties, mechanical dynamics, and the application of nanocomposite films. This section identifies key research themes, traces historical progress, and highlights emerging trends while underscoring the significance of collaboration and the influence of pivotal studies that have shaped the field. Lastly, in the "Literature Review Guided by Artificial Intelligence" section, the paper introduces a revised approach for researching nanocomposites through AI-guided techniques. This approach prioritizes articles published in 2023 based on citation frequency. Here, the focus is on exploring the relationship between nanocomposites and their electrical properties, emphasizing their fundamental interactions and impact on electrical characteristics. Various nanocomposite systems are covered, highlighting their composition, structure, and functionality. Findings from recent studies are integrated to provide a comprehensive overview of the current state of knowledge in this area. Notably, the sentiment analysis, anchored by an average sentiment score of 0.638771, underscores a positive trajectory in academic discourse, emphasizing the growing recognition of the potential of nanocomposites. The bibliometric exploration maps the intellectual domain, emphasizing pivotal research themes and the influence of crosslinking time on nanocomposite attributes. While this study is thorough, it acknowledges its limitations and advocates for broader database inclusion in future research endeavors. This work elucidates the prevailing trends in nanocomposite research, emphasizing the indispensable role of computational tools in comprehending this vast wealth of information.

Heptanuclear {GdIII7} (complex 1) and tetradecanuclear {GdIII14} (complex 2) have been synthesized using a Rhodamine 6G ligand HL (Rhodamine 6G salicylaldehyde hydrazone) and characterized. Complex 1 has a rare disc-shaped structure, where the central Gd ion was connected to the peripheral six GdIII ions via CH3O-/μ3-OH- bridges. Complex 2 has an unexpected three-layer double sandwich structure with a rare μ6-O2- ion in the center of the cluster. Magnetic studies revealed that complex 1 exhibits a magnetic entropy change of 17.4 J kg−1 K−1 at 3 K and 5 T. On the other hand, complex 2 shows a higher magnetic entropy change of 22.3 J kg−1 K−1 at 2 K and 5 T.

This work compares the multi-element analysis of human hair and nails using inductively coupled plasma mass spectrometry (ICP-MS) with an easy, fast, cheap, non-destructive method using energy dispersive x-ray fluorescence (EDX-RF). The ICP-MS-based method was more sensitive (over 30 elements could be quantified) and costly (requiring more time, sample, and chemicals). The EDX-based method required laboratory and certified reference materials made of hair for instrument calibration. It was less sensitive (16 elements could be quantified: S, Si, Ca, Br, Fe, Cu, Cr, Mg, Si, K, Mn, Ni, Zn, Se, Sr, Pb), but it allowed to replace troublesome grinding with the dissolution of keratin-based material with alkalic agent (tetramethylammonium hydroxide, TMAH) and formation of stable for days pellets. The method is simple, enables automation, and, due to the modification of wells in the autosampler of the EDX system by immersion of home-designed inserts, it requires smaller amounts of biological material and binder (down to 70 mg instead of 500 mg required by commercially available instrument) to perform analysis. It was concluded that the EDX-based method offers complementary selectivity and sensitivity to ICP-MS with the possibility of the reuse of the sample for further analysis.

Bipyridine and its related compounds are starting materials or precursors for a variety of valuable substances, such as biologically active molecules, ligands for catalysts, photosensitizers, viologens, and supramolecular architectures. Therefore, it is important to classify the synthesis methods and know their characteristics. Representative examples include the methods using homo- and heterocoupling of pyridine derivatives in the presence of catalyst. Because bipyridine compounds have a high ability to coordinate with metal centers, a decrease in catalytic activity and yield is often observed in the reaction system. To address this issue, the review provides insight into recent advances in bipyridine synthesis using metal complexes under both homogeneous and heterogeneous conditions. Moreover, the review also sheds light on strategies for bipyridine synthesis involving sulfur and phosphorous compounds. These alternative pathways offer promising avenues for overcoming challenges associated with traditional-catalyzed methods, providing a more comprehensive understanding of the synthesis landscape.

In this work, a ZIF-67/MWCNTs/Nafion sensor platform was constructed based on the good adsorption capacity of ZIF-67, the electrical conductivity of multiwalled carbon nanotubes (MWCNTs) and the excellent chemical stability of Nafion for the detection of Cu2+ in water. Meanwhile, the modified materials were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), BET specific surface area test, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectrometry (FT-IR). Cyclic voltammetry (CV), electrochemical impedance (EIS), and square wave solvation voltammetry (SWSV) electrochemical methods were used to perform applied test studies on ZIF-67/MWCNTs/Nafion/GCE. The results show that ZIF-67/MWCNTs/Nafion/GCE has high sensitivity (57.5 μA/μM) and a low limit of detection (15.0 nM) for the electrochemical detection of Cu2+ ions in an electrochemical sensing system. It has high adsorption selectivity for Cu2+, and the recovery of Cu2+ in real water reached 98.6%-103%. The modified electrode has good repeatability, reproducibility, anti-interference, and stability, which makes this sensing platform can be practically applied to the detection of domestic water.

Printed circuit boards (PCBs) make up 3 to 5% of all electronic waste. The metal content of spent PCBs can reach 40%. They usually contain valuable metals - Ag, Au, Pd, as well as other metals such as Cu, Sn, Pb, Cd, Cr, Zn, Ni and Mn. However metallic part of whole PCB is 40-60% including Cu layers between the fiberglass-polymer layers. The paper describes economics of the the valuable metals (Ag, Au, Pd) containing concentrate preparation from raw PCB. Considered the influence of pre-treatment method of PCB before the extraction of valuable metals on the extraction self-cost change. The disintegration method is based on the high-energy impact of the particles of the material to be ground, thus causing the separation of the metallic components of the PCB. In the course of the work, single and double direct grinding by the method of disintegration was studied. For the calculation the test batch 10’000 kg of two types of PCB were taken for estimation of the self costs and potential profit in case of complete valuable metals (Ag, Au, Pd) plus Cu extraction. Is shown that from 10’000 kg of studied PCB is possible to obtain 1144 and 1644 kg of metal-rich concentrate, which further should be subjected to electro-hydrochlorination for metals leaching. The main findings shows, that despite of high content of Cu in studied PCB, the commercial value is insignificant in total income from the Ag, Au and Pd sale. Was established correlation of the self-cost decrease after separative disintegration of PCB by metal content increase (by specific metals such as Au, Ag, Pd and also Cu) with the metal potential yield after extraction.

The widespread use of hydrophilic intraocular lenses (IOL) in eye surgery, fabricated by poly-2- (hydroxyethylmethacrylic acid) (PHEMA), has highlighted their calcification as a serious problem, which implies their surgical explantation a rather risky process. The field of biomaterials has been developing rapidly in recent years with research interest turning to the development of novel ma-terials which involve either copolymers of PHEMA or protective functional coatings. Graphene coatings are particularly attractive because of the respective unique properties. In the present work we present the results of the investigation of the development of graphene coatings on hydrophilic IOLs and their subsequent performance with respect to calcification opacification. Hydrophilic IOL with water content of 18% by weight, were coated with graphene oxide (GO) by equilibration with GO suspensions in water. The concentrations of the suspensions ranged 1x10-4 to 20x10-4 % w/v. The GO suspensions were equilibrated with the IOLs for 5 days at constant temperature, 37°C, rotated in 30 mL tubes end over end. This treatment, resulted in the formation of a uniform coating of GO on the IOLs verified by scanning electron microscopy (SEM) and other physicochemical methods. The contact angle of the GO coated IOLs decreased significantly in comparison with the uncoated. The GO-coated IOLs exhibited higher tendency to calcify in supersaturated solutions simulating aqueous humor (SAH). The growth rate of hydroxyapatite (Ca5(PO4)3OH, HAP) on GO-coated IOLs was higher, in comparison with the respective untreated IOLs. The conversion of the GO coating by reduction with phenyl hydrazine resulted in the formation of reduced graphene (rGO) surface film, identified by Raman and XPS spectroscopy. of the rGO film was hydrophobic (contact angle 100 o) and did not calcify in supersaturated calcium phosphate solutions.

(1) Background: Since fullerene C60 is insoluble in water and is toxic, it is not applicable in biomedicine and cosmetics. For this reason, the first derivative FD-C60 (fullerenol) was synthesized, which solved the problem of solubility in water and partially reduced toxicity. In order to maximally reduce toxicity and increase biomedical efficiency, the second derivative SD-C60 (3HFWC- Hyper-Harmonized-Hydroxylated Fullerene Water Complex), was created. (2) Methods: In order to obtain the most reliable data, several different methods are applicable in the characterization of FD-C60 and SD-C60 with water layers (NIR, FTIR, 13C-NMR,  1H-NMR, TGA/DTA, XRD, AFM/MFM etc.). (3) Results: FD-C60 as an individual structure is about 1.3 nm in size, while SD-C60 as an individual structure is 1030 nm in size. The aforementioned methods showed that SD-C60 contains water layers, which explains the difference between those two structures in the physicochemical properties, and their effects on biomolecules. (4) Conclusions: Based on the above methods and techniques, FD-C60 and SD-C60 are two different substances in terms of size, structure, and physicochemical properties; FD-C60 at 100C has endothermic characteristics and SD-C60 at 133C has exothermic characteristics, FD-C60 possesses water molecules only from humidity, while SD-C60 has water molecules from both humidity and extra water molecules in layers, the zeta potential of FD-C60 is -25.85 mV, while it is -43.29 mV for SD-C60.

The current investigation presents porous ceramic materials prepared of cenospheres prepared by spark plasma sintering. The impact of sintering temperature, mould diameter (20 and 30 mm diameter) and cenosphere size on the properties of the sintered material was investigated. Shrinkage of the samples during sintering started at 900 °C. Sample shrinkage during sintering increases with increasing temperature and decreases with increasing mould size; increasing sample sintering temperature increases the apparent density of all sample series CS 63-150 µm in 20 mm mould from 0.97 to 2.3 g·cm-3 at 1050 - 1300 °C, in 30 mm mould 0.81 - 1.87 g·cm-3 at 1050 - 1200 °C, in 50 mm mould 0.54 - 0.75 g·cm-3 at 1050 - 1150 °C, while CS 150-250 µm in 20 mm mould 0.93 - 1.96 g·cm-3 at 1050 - 1200 °C. Total porosity decreases from 61.5% to 3.9% with increasing sintering temperature from 1050 to 1250 °C, while open porosity reduces at lower temperatures, with closed porosity being highest in samples sintered at 1150 °C. When the sintering temperature increases from 1050 to 1300 °C, the compressive strength of the CS 63-150 samples produced in a 20 mm mould increases from 11 MPa to 312 MPa. These results correlate with the Rice model, which describes an exponential dependence of compressive strength on material porosity and fully dense material compressive strength.

An efficient approach to the previously unknown furo[2',3':2,3]pyrrolo[2,1-a]isoquinoline deriv-atives from readily available 1-R-1-ethynyl-2-vinylisoquinolines is described. The reaction fea-tures a simple procedure, occurs in hexaflouroisopropanol and does not require elevated tem-peratures. It has been found that the addition of glacial acetic acid significantly increases the yields of the target spirolactone products. Using trifluoroethanol instead of hexaflouroisopro-panol results into formation of pyrido[2,1-a]isoquinolines.

The state of Veracruz has ample water resources. However, due to population and industrial growth, there has been an increase in the discharge of wastewater into surface water bodies. To analyze the water quality in the Bobos River, Veracruz, and its sustainability, researchers collected nine samples from nine different points in the reservoir. They measured various parameters such as temperature, pH, dissolved oxygen, conductivity, total nitrogen, nitrate, chemical oxygen demand, total phosphorus, phosphate, dissolved solids, and fecal coliforms. The results showed that the river's water quality is at risk. The concentration of pollutants such as chemical oxygen demand and fecal coliforms is high. Conductivity values ranged from 0.26 to 3.81 mS. If preventive and corrective measures are not taken, the river's ability to purify pollutants will be severely compromised. This study evaluates the physical, chemical, and microbiological characteristics of the water in Bobos River. It specifically investigates the influence of the nearby citrus industry on the river's water quality. The study also aims to promote environmental sustainability.

The healing of osteochondral defects (OCD) resulting from injury, osteochondritis, or osteoarthritis in middle- and old-age individuals, bearing lesions in the cartilage and bone, pain, and loss of joint function, presents challenges to the clinical practitioners because of non-regenerative cartilage and the limitations of current therapies. Bioactive peptide-based osteochondral (OC) tissue regeneration is becoming more popular because it does not have the immunogenicity, misfolding, or denaturation problems associated with original proteins. Periodically, reviews are published on the regeneration of bone and cartilage; however, none of them address the simultaneous healing of these tissues in the complicated heterogeneous environment of the OC interface. As regulators of cell adhesion, proliferation, differentiation, angiogenesis, immunomodulation, and antibacterial activity, potential therapeutic strategies for OC defects utilizing bone and cartilage-specific peptides should be examined and investigated. Therefore, the main goal of this review is to study how they contribute to the healing of OC defects, either alone or in conjunction with other peptides and biomaterials.

This study provides an in-depth examination of the binary system of n-Nonadecane and 1-Octadecanol, representative of plant cuticular waxes. It emphasizes the crystallization and phase transitions in this hydrocarbon mixture. Using Differential Scanning Calorimetry (DSC) and Fourier Transform Infrared (FTIR) spectroscopy, the research uncovers detailed thermal properties and phase behaviors. The findings reveal the distinct phase transitions and enthalpy changes of each component in the binary system. This research is significant for its implications in under-standing the structural properties of plant waxes. Such insights are crucial for enhancing the effi-ciency of fertilizer and pesticide absorption in plant leaves, with broad applications in bionics and materials science. This study not only furthers the understanding of identifying specific phase transitions for each compound, facing challenges in detecting subtle changes using DSC. The re-search enhances understanding of plant cuticle waxes through FTIR analysis, revealing intricate molecular interactions and structural complexities. but also opens avenues for improved agri-cultural practices and material engineering, potentially influencing future innovations in these fields.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

This study aimed to investigate the incorporation of micronized salt (MS) to reduce sodium content in fresh sausages while preserving technological, chemical, textural, and sensory characteristics. Four treatments were prepared: control (C) with 2.0% regular salt; M2.0% with 2.0% micronized salt; M1.5% with 1.5% micronized salt; and M1.0% with 1.0% micronized salt. Half of the micronized salt treatment was mixed with the fat during the processing of the fresh sausages. It was possible to achieve a 50% reduction in sodium (M1.0%) in the fresh sausages without negative effects on most technological, chemical, and textural parameters, which did not differ from the control treatment (C). Conversely, "chewiness" decreased in M2.0% compared to the control (C) due to mixing micronized salt with the fat. The sodium reduction did not impact the temporal sensory profile and overall liking. Therefore, using micronized salt in fresh sausages reduces sodium content without affecting sensory traits and product stability.

Surfactants are widely used in the synthesis of nanoparticles, as they have a remarkable ability to direct their growth to obtain well-defined shapes and sizes. However, their post-synthesis removal is a challenge, and the methods used often result in morphological changes that defeat the purpose of the initial controlled growth. The cleaning methods could be classified as thermal or non-thermal. In general, the structure of materials can be better preserved by non-thermal treatments. After the removal of surfactants, the highly active surfaces of nanomaterials may undergo structural reconstruction by exposure to a different environment. Thus, ex situ characterization after air exposure may not reflect the effect of the cleaning methods. In situ characterization is required to better understand the impact of various cleaning procedures. Combining X-ray photoelectron spectroscopy, in situ infrared reflection absorption spectroscopy, and environmental transmission electron microscopy measurements with CO probe experiments, we investigated different surfactant-removal methods to produce clean metallic Pt nanoparticles from surfactant-encapsulated ones. Non-thermal plasmas show the best results. It was demonstrated that both UV-ozone treatment and room temperature O2 plasma treatment lead to the formation of Pt oxides on the surface after the removal of the surfactant. These oxides are reduced to metallic Pt during in situ CO probe experiments. On the other hand, when H2 was used for plasma treatment, the Pt0 oxidation state and nanoparticle size distribution were preserved. In addition, H2 plasma treatment can reduce Pt oxides after O2-based treatments, resulting in metallic nanoparticles with clean surfaces. Thermal reduction in hydrogen leads to carbon species emerging onto nanoparticle surfaces after heating and agglomeration of Pt nanoparticles. Particularly, O2-based thermal treatments result in the formation of aggregates consisting of small nanoparticles. These findings provide a better understanding of the various options for surfactant removal from metal nanoparticles and point toward non-thermal plasmas as the best route if the integrity of the nanoparticle needs to be preserved.

Five new cembrane-type diterpenes, lobocalines A–E (1–5), and four new steroids, lobocalines F–I (9–12), along with six known related compounds (6–8 and 13–15) were isolated from the Yalong Bay soft coral Lobophytum catalai. The structures of the new compounds were elucidated by extensive spectroscopic analysis, NMR calculation with DP4+ analysis, time-dependent density functional theory-electronic circular dichroism (TDDFT-ECD) calculations, X-ray diffraction analyses, and the comparison with the reported spectroscopic data of known compounds. Further, with the aid of X-ray diffraction analysis, the structure of lobocrasol B (15) was firmly revised as 15a. In in vitro bioassays, compound 2 showed moderate antibacterial activities against fish pathogenic bacteria Streptococcus parauberis KSP28 and Phoyobacterium damselae FP2244 with minimum inhibitory concentration (MIC) values of 8.7 and 17.3 µg/mL, respectively. All the steroids exhibited antibacterial activities against the S. parauberis KSP28 with MIC values ranging from 12.3 to 53.6 µg/mL. Compounds 2, 7 and 14 have remarkable inhibitory effects on the hemolysin production of Staphylococcus aureus, while compounds 8–12 have medium inhibitory effects on the pyocyanin production in Pseudomonas aeruginosa.

Formaldehyde, sulfuric acid and salicylic acid were combined to create 3,3’-methylenebis[2-hydroxybenzoic acid] (MHB) ligand, which was subsequently permitted to bind with zinc ions. The ligand and its zinc (II) complex (Zn-MHB) have been described by a combination of elemental analyses, spectral (UV-Vis, IR, MS, NMR), XRD, TEM as well as TGA measurement. The ligand has been suggested to coordinate to the zinc center in tetradentate manner forming binuclear tetrahedral complex. An X-ray analysis indicated a considerable difference between MHB (crystalline) and Zn-MHB (amorphous). UV-Vis spectra were used to determine the optical properties such as bandgap, refractive index, optical conductivity and penetration depth. Possibility of employing the samples for optoelectronic applications was indicated from the band gap values which underlie the range of semiconductors. TEM revealed spherical shapes and mutation of ligand particles into nano-scale by complexation. The antimicrobial potential of the MHB towards gram-positive and negative bacterial growths has been investigated. The results suggested that it would be possible to employ MHB to stop bacterial development, particularly salmonella typhimurium. Cytotoxicity of the MHB was assessed against two types of mammalian cells: VERO (the kidney of an African green monkey) and HFB4 (human skin melanocytes). Lower sensitivity was observed in VERO cells.

Structural hydroxide groups in layered magnesium-aluminum double hydroxides were partially replaced by fluoride ions. Fluorinated and fluorine-free materials were used as hosts for two dyes, carminic acid and hydroxyl naphthol blue, resulting in a hybrid pigment color palette. Additionally, the pigments were protected with a magnesium hydroxide phase to prevent the color from fading over time. The color properties of the pigments were significantly influenced by the host of dye, since the presence of fluorine directly influences the acid-base properties of the layered double hydroxides. Finally, the pigments were successfully applied to prepare colored creams.

Ultra-low radioactive titanium alloy is a promising material for the manufacture of low-background detectors, which are being developed for experiments in astroparticle physics and neutrino astrophysics. Structural titanium is manufactured on an industrial scale from titanium-sponge. The ultra-low-background titanium-sponge can be produced on an industrial scale with a contamination level of less than 1 mBq/kg of uranium and thorium isotopes. The pathways of contaminants during the industrial production of structural titanium have been analyzed. The measurements have been carried out using two methods: inductively coupled plasma spectroscopy (ICP-MS) and gamma-spectroscopy using high-purity germanium detectors (HPGe). It has been shown that the level of contamination with radioactive impurities does not increase during remelting of titanium-sponge and mechanical processing. We examined titanium-alloys samples obtained at different stages of titanium production, namely, an electrode compaction, a vacuum arc remelting with a consumable electrode (VAR), and a cold rolling of titanium-sheets. It has been found out that all studied samples will be a source of uranium and thorium contamination of the final titanium-alloys. It has been established that the only product allowed obtaining ultra-low-background titanium was the VT1-00 which is manufactured without master alloys addition..

A homogenized, supersaturated Al-Zn-Mg-Zr alloy was processed by severe plastic deformation (SPD) using high-pressure torsion (HPT) technique for different revolutions at room temperature to get ultrafine-grained (UFG) microstructure. The microstructure and mechanical properties of the UFG samples were then studied by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), as well as by tensile and hardness measurements. Emphasis was placed on the effect of shear strain on the evolution of microstructure of the investigated alloy. Experimental results have shown a very interesting evolution of the decomposed microstructure in a wide range of shear strains imposed by HPT. While the global properties, such as the average grain size (~200 nm) and hardness (~2.2 GPa) appeared unchanged, the local microstructure was continuously transformed. After 1 turn of HPT, the decomposed UFG structure contains relatively large precipitates inside grains. In the sample processed by 5 turns in HPT, segregation of Zn atoms into grain boundaries (GBs) can also be observed. After 10 turns, more Zn atoms have segregated into GBs and only smaller size precipitates can be observed inside grains. The intensive segregation of solute atoms into GBs may significantly affect the ductility of the materials, leading to its ultralow-temperature superplasticity. Our findings pave the way for achieving advanced microstructural and mechanical properties in nanostructured metals and alloys by engineering their precipitation and segregation by means of applying different HPT regimes.

Metal-organic frameworks (MOFs) represent the largest class of materials among the crystalline porous materials ever developed and have attracted attention as core materials for separation technology. Their extremely uniform pore aperture and nearly unlimited structural and chemical characteristics have attracted great interest and promise in applying MOFs to adsorptive and membrane–based separations. This paper reviews the recent research and development of MOF membranes for gas separation. Strategies for polycrystalline membranes and mixed matrix membranes are discussed, with a focus on separation systems involving hydrocarbon separation and CO2 capture. Challenges and opportunities for the industrial deployment of MOF membranes are also be discussed, providing guidance for the design and fabrication of future high-performance membranes. The contributions of the underlying mechanism to separation performances, and the adopted strategies and membrane processing technologies for breaking the selectivity/permeability trade–off are discussed.

Innovations in drug delivery systems are crucial for enhancing therapeutic efficiency. Our research presents a novel approach based on Electro-fluid dynamic atomization (EFDA) to fabricate core-shell monophasic particles (CSMp) from sodium alginate blends of varying molecular weights. This study explores the morphological characteristics of these particles in relation to material properties and process conditions, highlighting their potential in drug delivery applications. A key aspect of our work is the development of a mathematical model that simulates the release kinetics of small molecules, specifically sodium diclofenac. By assessing the diffusion properties of different molecules and gel formulations through transport and rheological models, we have created a predictive tool for evaluating the efficiency of these particles in drug delivery. Our findings underscore two critical independent parameters for optimizing drug release: the external shell thickness and the diffusivity ratios within the dual layers. This allows for precise control over the timing and intensity of the release profile. The study advances our understanding of EFDA in the fabrication of CSMp and offers promising avenues for enhancing drug delivery systems by tailoring release profiles through particle characteristic manipulation.

The novel coronavirus disease (COVID-19) pandemic has resulted in over 720 million confirmed cases and 7 million deaths worldwide, with insufficient treatment options. Innumerable efforts are being made around the world for faster identification of therapeutic agents to treat the deadly disease. Postacute sequelae of SARS-CoV-2 infection or COVID-19 (PASC), also called Long COVID, is still being understood and lacks treatment options as well. A growing list of drugs are being suggested by various in silico, in vitro and ex vivo models, however currently only two treatment options are widely used: the RNA-dependent RNA polymerase (RdRp) inhibitor remdesivir, and the main protease inhibitor nirmatrelvir in combination with ritonavir. Computational drug development tools and in silico studies involving molecular docking, molecular dynamics, entropy calculations and pharmacokinetics can be useful to identify new targets to treat COVID-19 and PASC, as shown in this paper. We have investigated bisphosphonates which can bind competitively to nidovirus RdRp-associated nucleotidyl (NiRAN) transferase domain, and systematically down selected seven candidates for further evaluation (CHEMBL608526, CHEMBL196676, CHEMBL164344, CHEMBL4291724, CHEMBL4569308, CHEMBL387132, CHEMBL98211). Interestingly, one of these (CHEMBL608526) very closely resembles the approved drug minodronate, and another (CHEMBL98211) resembles the approved drug zoledronate.

The energy crisis is currently a major topic in scientific and managerial discussions in the building and construction industry. While employing low-cost strategies for reducing energy usage is beneficial for principals and decision-makers, the primary purpose of this study is to recommend the use of phase change materials (PCM) to improve cooling and heating load management in buildings. In order to accomplish this, the study applies design-builder simulations to a developing country case study. The results indicate that integrating PCM in buildings can reduce energy usage by around 6 percent. Although this value may be lower than other techniques, it is nevertheless important for reaching green building goals in both developed and developing nations. The case study, which takes place in a four-season region, demonstrates the significant potential of the PCM system for both cooling and heating energy management. In addition, the reciprocal performance improvement of PCMs is a remarkable characteristic, especially when contrasted to some conventional systems that focus on a single energy management objective in buildings. Lastly, it should be underlined that the suggested platform is consistent with Sustainable Development Goal 7 (Affordable and Clean Energy Targets).

ABSTRACT Heavy metals have been classified as dangerous environmental pollutants. Interest in feasible ways to reduce heavy metals pollution is a noble goal. Adsorption is an effective method based on its effectiveness and low- cost. Nowadays, low-cost bio-sorbents have been utilized to replace costly expensive adsorbents. Rich cellulose materials are effective heavy metal adsorbents, and their performance can be enhanced via chemical modification. The present work reviews the steady progress in the utilization of agriculture by-product wastes as heavy metal bio-sorbent. The unique advantages of these by-products such as renewability, abundance, simple processing, and low cost, justifier this work. The results confirm that the chemically treated agro-wastes exhibit high- removal efficiency (reaches 95% in most cases). The adsorption isotherm studies indicate that the concentration of the metal ions has a significant effect on the adsorption process. The Freundlich model provides a physical adsorption model of the metal ions on the bio-sorbent surface. Langmuir isotherm offers an estimate of the effect of different factors on the efficiency of the process. The adsorption kinetics studies offer an idea of reaction pathways including the adsorption mechanism and the efficiency of the metal ion removal. Applying the pseudo-first-order and pseudo-second-order models describes the adsorption kinetics. This information can be utilized in developing effective strategies to remove heavy metal ions using chemically treated agro-waste. The data confirmed that chemical modification is a significant parameter in the efficiency of metal ion removal. The feasibility and effectiveness of using these cellulosic by-products as bio-sorbent should be given attention and encouraged.

One of the most widely available and extensively produced varieties of industrial hemp, which generates a substantial amount of consumer-increasing waste in the form of hemp cellulose. In this study, recycling with a compressed and high-speed method that combines crushing and alkali treatment effectively converts leftover hemp fiber into ultrafine powder. SEM (Scanning Electron Microscopy), AFM (Atomic Force Microscope), FTIR (Fourier-transform Infrared Spectroscopy), and XRD (X-ray Diffraction) examined the original morphology of hemp fiber treated with alkali, fiber heated to 200 ℃, and crushed powder. Particle size, crystallinity, fiber surface, and strength increased and decreased. It became apparent that fiber strength decreased and fiber roughness significantly increased after alkali treatment. Fiber increased significantly, and crystallinity decreased after crushing. It was simple and effective for converting the leftover hemp fiber into micron-sized powder. In about 3 to 5 minutes, approximately 1 kg of dry ultrafine powder with a particle size of 10.44 μm was produced. This production method will significantly enhance future industrial applications of waste hemp fiber.

The three-component reaction of enaminones, benzaldehyde and hydrazine-HCl or four-component reaction of enaminones, benzaldehyde, hydrazine–HCl and ethyl cyanoacetate in water in the presence of catalytic amount of ammonium acetate has been devised as a straightforward , sustainable approach for the synthesis of 1-H-pyrazole, N-aminopyridine and pyrazol[3,4-b]pyridine derivatives . The key benefits of this approach is simple experimental procedure associated with cost effective and environmentally friendly techniques.

The biofibres wide application as mortars enhancement have been so far restricted by factors related to their chemical composition and hygroscopic nature. Their hydrophilic behavior increases the water demand of mortar-mixtures and diminishes their adhesion to the matrix, while further moisture-related fibre degradation issues may arise. Additionally, the natural fibres seem to be susceptible to degradation caused during the exposure to alkaline environments conditions, such as those of cement mortars, restricting their utilization in construction industry. Therefore, the current study focusses on the potential of fibre modification through treatments that would permanently alter their structure and chemical composition in the whole mass or surface towards their performance improvement. In this study, mild hydrothermally treated wood fibres of black pine and beech species were prepared and incorporated in cement mortars to assess their performance, applying the proportion of 1.5% v/v in the mortar. The mortars workability (at fresh state), physical, hygroscopic, chemical, thermal, and mechanical characteristics at the age of 28, 90 and 365 days and weathering performance by subjecting them at different artificial ageing environments (freeze-thaw cycles or outdoor exposure) were examined. The results indicated the beneficial role of the treated fibres in the dimensional stability, flexural strength, thermal insulation properties and capillary absorption of the mortar specimens, especially during ageing process, with the black pine fibres to reveal the highest improvement. The hydrothermally treated wood fibres seem to ensure the integrity maintenance of cement mortars under all ageing conditions, proving that the specific bio-additives could provide low-cost and eco-friendly mortar enhancement pathways.

In this work, Density Functional Theory (DFT) calculations were employed to study the photocatalytic CO2 to CO reduction by a series of Pt(II) square planar complexes with general formula [Pt(5-R-dpb)Cl] (dpb = 1,3-di(2-pyridyl)benzene anion, R = H, N,N-dimethylaniline,T thiophene, diazaborinine). The CO2 to CO conversion process is thought to proceed via two main steps, namely the photocatalytic/reduction step and the main catalytic step. The simulated absorption spectra exhibit strong bands in the 200 – 400 nm UV-Vis region. The calculated excited state reduction potentials are in the range 0.32 — -0.36 V revealing that the reductive quenching of the T1 state of the complexes could be modulated with suitable changes of the N^C^N pincer ligands. The CO2 fixation and activation by the ‘real’ three coordinated Pt(II) catalyst/intermediate is predicted to be favorable with Pt-CO2 bond dissociation energies, D0 in the range -36.9—-10.3 kcal/mol. The nature of the Pt-CO2 bond is complex with covalent, hyperconjugative and H-bonding interactions prevailing the repulsive electrostatic interactions. The main catalytic cycle is estimated to be a favorable exergonic process.

Barley straw was used to reinforce PHB in a discontinuous semi-industrial process. Four different fibres were used as reinforcing material : sawdust (SW), defibred (DFBF), delignified (DBF) and bleached (BBF) fibres. Looking at the mechanical properties, onlythe elastic moduli (Et) revealed an improvement. Oppositely, the strengths at break, under both tensile and bending assays, tended to decrease, evidencing a poor affinity between both components. Thanks to the mechani-cal treatment applied on the fibre, DFBF appeared as the most promising filler with the mechani-cal properties of the composites closest to those of neat PHB. DFBF-based composites were then produced by means of a process intensification using a twin-screw extruder, and then moulded into flowerpots. Mechanical results showed almost the same properties between the discontinuous and intensification processes. The suitability of the material to be used on agriculture flowerpots was demonstrated by simulation. . PHB-DFBF composite material can be considered an alterna-tive to replace petrol-based products for applications in agriculture and horticulture.

Quality-changed behavior of ultraviolet light absorber (UVA: UV-326) in polymers (PP, HDPE, LDPE, PLA and PS) over time during degradation was studied with an enhanced degradation method (EDM) using sulfate ion radical in seawater. EDM was employed to homogeneously degrade the entire polymer samples containing the UVA. The PP and PS samples containing 5-phr UVA films whitened rapidly due to formation of numerous grooves or crushed particles. The UVA loss rate of PS with the higher Tg was much slower. The crystalline polymers, with the exception of PS, were similar in the behavior of the change in UVA loss rate with respect to degradation time. The significant increase in initial loss rate observed during EDM degradation was due to microplasticization. A similar increase in microplasticization rate occurred with the PS, but the intermolecular interaction between UVA and PS did not result in as pronounced its increase in loss rate as with other polymers. The UVA chemical structure was not altered by EDM degradation. These results revealed that the UVA leaching from the polymer matrix was the primary cause of the loss.

The product of ozonolysis, Glycero-(9,10-trioxolane)-trioleate (ozonide of oleic acid triglyceride, [OTOA]), was incorporated into polylactic acid/polycaprolactone (PLA/PCL) blend films in the amount of 1, 5, 10, 20, 30, and 40% w/w. The morphological, mechanical, thermal and antibacterial properties of the biodegradable blend after the OTOA addition were studied. According to DSC and XRD data, the crystallinity degree of PLA/PCL+OTOA films tended to decrease with increase in OTOA content that could be explained by its plasticizing effect. Morphological analysis showed that the structure of the films with the OTOA concentration above 20% drastically changed. Specifically, the interface between the PLA/PCL matrix and OTOA was formed, thereby forming a capsule with the embedded antibacterial agent. The moisture permeability of the resulting PLA/PCL+OTOA films decreased due to the formation of uniformly distributed hydrophobic amorphous zones that prevents water penetration. This architecture affects the tensile characteristics of the films: strength decreases to 5.6 MPa, elastic modulus E by 40%. The behavior of film elasticity is associated with the redistribution of amorphous regions in the matrix. Additionally, PLA/PCL+OTOA films with 20, 30 and 40% of OTOA showed good antibacterial properties on Pseudomonas aeruginosa, Raoultella terrigena (Klebsiella terrigena) and Agrobacterium tumefaciens. Developed PLA/PCL+OTOA films could be used as packaging materials and wound dressings. By variation of the OTOA content, it is possible to tailor the physical-chemical and antibacterial properties of the developed films for various applications.

Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.

Biodiesel is one of the most popular biofuels as it is a promising substitute of the conventional diesel fuel, but for now it cannot be used as a stand-alone fuel due to its low oxidative stability. For this reason, the last years there have been efforts for its upgrading through the partial hydrogenation of the fatty acid methyl esters (FAMEs) that biodiesel consists of. This procedure succeeds in resolving the problem of low oxidative stability, but in some cases a new problem arises as the non-selective hydrogenation is deteriorating the fuel’s cold flow properties, which are crucial for its operation without damaging the vehicle’s engine. More specifically, the problem of deteriorated cold flow properties is caused by the formation of trans-monounsaturated FAMEs and fully saturated FAMEs while the hydrogenation reaction is taking place. The hydrogenated biodiesels are preferred to contain more cis-monounsaturated FAMEs, because these are considered to have the best combination between high oxidative stability and good cold flow properties. As a result, various systems and methods have been tested in order to achieve a selective partial hydrogenation of biodiesel’s FAMEs. In this review article, the catalytic systems and methods that stood out in various researches are presented and the factors that lead to the best possible outcome are investigated and discussed.

Highly transparent, conductive nanosheets are extremely attractive for advanced optoelectronic applications. Previously, we have demonstrated that transparent, conductive Au nanosheets can be prepared by UV irradiation of Au nanoparticle (AuNP) monolayers spread on water, which serves as the subphase. In this study, we show that this UV irradiation technique can easily be extended as a nanosheet modification method by using subphases containing metal ions. That is, aqueous solutions containing Au and Ag ions are effective in modifying Au nanosheets. HAuCl4 solutions increased Au nanosheet thickness, which improved conductivity, but reduced transparency. On the other hand, use of aqueous AgNO3 and CH3COOAg solutions yielded Au-Ag hybrid nanosheets; however, their morphologies depended on the electrolytes used. Homogeneous Au-Ag nanosheets from AgNO3 and AuNPs covered with an Ag nanosheet from CH3COOAg were also produced. Further, these Au-Ag hybrid nanosheets had high conductivity without reduced transparency. Therefore, this UV irradiation method, modified by adding metal ions is quite effective at improving and diversifying properties of Au nanosheets.

Owing to its properties, boron carbide has been applied in scientific and industrial fields. For this reason, B4C powders should be characterized by high purity and homogeneity in grain size and shape. In this study, boron carbide was prepared using precursors obtained by a hydrothermal method, and the grain morphology of the product was investigated. Boric acid and the saccharides glucose, fructose, inulin, and sorbitol were used as the precursors. Two precursor dehydration methods, freeze-drying and recrystallization, were compared. The precursors were subjected to DLS grain size and FT-IR spectrophotometric studies, and SEM observations of the precursors and products were performed, confirming that boron carbide powders with submicron spherical grains could be successfully synthesized.

Formaldehyde, sulfuric acid and salicylic acid were combined to create 3,3’-methylenebis[2-hydroxybenzoic acid] (MHB) ligand, which was subsequently permitted to bind with zinc ions. The ligand and its zinc (II) complex (Zn-MHB) have been described by a combination of elemental analyses, spectral (UV-Vis, IR, MS, NMR), XRD, TEM as well as TGA measurement. The ligand has been suggested to coordinate to the zinc center in tetradentate manner forming binuclear tetrahedral complex. An X-ray analysis indicated a considerable difference between MHB (crystalline) and Zn-MHB (amorphous). UV-Vis spectra were used to determine the optical properties such as bandgap, refractive index, optical conductivity and penetration depth. Possibility of employing the samples for optoelectronic applications was indicated from the band gap values which underlie the range of semiconductors. TEM revealed spherical shapes and mutation of ligand particles into nano-scale by complexation. The antimicrobial potential of the MHB towards gram-positive and negative bacterial growths has been investigated. The results suggested that it would be possible to employ MHB to stop bacterial development, particularly salmonella typhimurium. Cytotoxicity of the MHB was assessed against two types of mammalian cells: VERO (the kidney of an African green monkey) and HFB4 (human skin melanocytes). Lower sensitivity was observed in VERO cells.

Cassava Solid waste (Onggok) is a solid waste from the cassava-based tapioca industry, the starch content in Onggok is still 50-80 wt.% of residual starch, which can be used to produce maltodextrin for foods application. Furthermore, using cassava solid waste is beneficial in terms of the cost of raw materials. The starch content in cassava can be modified through enzymatic hydrolysis using α-amylase and β-amylase enzymes at 80oC and pH 5.5. Enzymatic hydrolysis was done using mixed enzymes that varied the concentration of α-amylase at 0,.1% and the β-amylase enzymes at 0.05, 0.1, and 0.5%. the concentration of cassava waste (Onggok) varied from 4%, 7%, 10%, and 13%. The optimum concentration of α-amylase and β-amylase enzymes are 0.1% and 0.1% respectively at time intervals of 1 minute resulting in a dextrose equivalent (DE) value 0f 5.7. The characteristics of maltodextrin were studied using scanning electron microscopy (SEM) to determine the morphology of the starch structure which had changed due to the enzyme hydrolysis. Simultaneous thermal analysis (STA) was studied to determine the Thermal stability of hydrolysis products. Maltodextrin produced from cassava waste (Onggok) has a DE value < 10, which has the potential to be used in the pharmaceutical industry

The surface configurations of the low-index facets of a set of spinel oxides are investigated using DFT+U calculations to derive surface energies and predict equilibrium nanoparticle shapes via the Wulff construction. Two very different conditions are investigated, corresponding to application either in heterogeneous catalysis or in electrocatalysis. First, the bare stoichiometric surfaces of NiFe₂O₄, CoFe₂O₄, NiCo₂O₄, ZnCo₂O₄ spinels are studied to model their use as high-temperature oxidation catalysts. Second, focusing attention on the electrochemical oxygen evolution reaction (OER), and on the CoFe₂O₄ inverse spinel as the most promising OER catalyst, we generate surface configurations by adsorbing OER intermediates, and, in an innovative study, we recalculate surface energies taking into account adsorption and environmental conditions, i.e., applied electrode potential and O₂ pressure. We predict that, under OER operating conditions, (111) facets are dominant in CoFe₂O₄ nanoparticle shapes, in fair agreement with microscopy measurements. Importantly, in the OER case we predict a strong dependence of nanoparticle shape upon O₂ pressure. Increasing O₂ pressure increases the size of the higher-index (111) and (110) facets at the expense of the (001) more catalytically active facet, whereas the opposite occurs at low O₂ pressure. These predictions should be experimentally verifiable and help define the optimal OER operative conditions.

Hydroxyapatite and b-tricalcium phosphate have been clinically applied as artificial bone materials due to their high biocompatibility. The development of artificial bones requires the verification of safety and efficacy through animal experiments; however, from the viewpoint of animal welfare, there is necessary to reduce the number of animal experiments. In this study, we utilized machine learning to construct a model that estimates the bone-forming ability of bioceramics from material fabrication conditions, material properties, and in vivo experimental conditions. We succeeded in constructing the two models as follows: ‘Model 1’, which predicts material properties from their fabrication conditions, and ‘Model 2’, which predicts the bone-formation rate from material properties and in vivo experimental conditions. By an inverse analysis of the two models, we proposed candidates for material fabrication conditions to achieve target values of bone-formation rate. Under the proposed conditions, the material properties of the fabricated material were consistent with the estimated material properties. Furthermore, a comparison between bone-formation rates after 12 weeks of implantation in the porcine tibia and the estimated bone-formation rate. This result showed that the actual bone-formation rates existed within the error range of the estimated bone-formation rates, indicating that machine learning consistently predicts the results of animal experiments using material fabrication conditions. We believe that these findings will lead to the establishment of alternative animal experiments to replace animal experiments in the development of artificial bones.

Recent advances in nanomaterials have been heavily influenced by low-dimensional nanocarbon allotropes. In particular, carbyne has attracted attention for its potential as a true one-dimensional carbon chain with sp1 hybridization. To maximize the capabilities of this material, we employ a focused data-driven inverse design approach based on the carbon nanomaterials genome concept. This involves using deep learning neural network models to identify key descriptors tied to desired properties, enabling property prediction and reverse engineering of nanocarbons. Our iterative approach entails: (i) gathering growth/property data on nanostructures; (ii) identifying informative numerical/categorical predictors; (iii) developing deep learning models mapping descriptors to properties; (iv) refining models with new insights; (v) determining required descriptors/conditions for target properties via inverse mapping; (vi) validating models by synthesizing predicted nanostructures; and (vii) enhancing models with validation data. This allows uncovering hidden growth-property connections, precisely tuning nanocarbons for desired attributes. We introduce new methodologies including exciting synergistic effects, synchronizing atomic vibrations, active screen plasma, energy-driven transformations, surface acoustic micro/nano-manipulation, doping and directed self-assembly to expose relationships and integrate insights into the inverse design flow. This research promises to accelerate discovery of next-generation low-dimensional nanocarbons with exceptional properties and applications.

Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

Silica nanoparticles synthesized solely from organosilanes naturally possess a greater number of organic functionalities than silica nanoparticles surface modified with organosilanes. We report the synthesis of organically modified silica (ORMOSIL) nanoparticles with mesoporous and surface rough morphology and with high surface area, made solely from vinyltrimethoxy silane. We chemically modified these vinyl silica nanoparticles using bromination and hydroboration, and demonstrated the high accessibility and reactivity of the vinyl groups with an ~85% conversion of the functional groups for bromination of both particle types, a ~60% conversion of the functional groups for hydroboration of surface rough particles and a 90% conversion of the functional groups for hydroboration of mesoporous particles. We determined that the mesoporous vinyl silica nanopar-ticles, while having a surface area that lies between the non-porous and surface rough vinyl silica nanoparticles, provide the greatest accessibility to the vinyl groups for boronation and allow in-corporating up to 3.1 × 106 B atoms per particle, making the resulting materials attractive for boron neutron capture therapy.

As for their large surface area and pore volume, three-dimensional covalent organic frameworks (3D COFs) have emerged as competitive porous materials. However, due to the structural dynamic behavior particularly for imine-linked 3D COFs, potentially unlock their potential for gas storage application. Herein, we showed a pre-locked linker strategy introduces breaking dynamic behavior in 3D COFs. A predesigned planar linker based 3,8-diamino-6-phenylphenanthridine (DPP) was prepared to produce non-dynamic 3D JUC-595, as benzylideneamine moiety in DPP locked the linker flexibility and restrict the molecular-bond rotation of the imine linkages. Upon solvent inclusion and release, the PXRD profile of JUC-595 remained intake, while JUC-594 with flexible benzidine linker experienced crystal transformation due to framework contraction-expansion. As a result, the activated JUC-595 achieved higher surface areas (754 m² g-1) than that of JUC-594 (548 m² g-1). Furthermore, improved CO2 and CH4 storages were also seen in JUC-595 compared with JUC-594. Impressively, JUC-595 recorded high normalized H2 storage capacity that surpass other reported high surface area 3D COFs. This works shows important insight on manipulating structural properties of 3D COF to tune the gas storage performance.

This work describes the synthesis and X-ray diffraction properties of spirocyclic compounds based on 8-azaspiro[5.6]dodec-10-ene. Diasteriomerically pure pyrrole derivatives were prepared from the spirocyclic 1,2,3-triazole using a coupling reaction. The resulting compounds were characterized via 1H and 13C NMR spectroscopy and HRMS, and the crystallographic characteristics of one of them were studied by X-ray diffraction.

Abstract: The expansion of global industries results in the release of harmful volatile acid vapors into the environment, posing a threat to various life forms. Hence, it's crucial to prioritize the development of swift sensing systems capable of monitoring these volatile acid vapors. This initiative holds great importance in safeguarding a clean and safe environment. This paper presents the synthesis and characterization of pyrene-based covalent organic frameworks (COFs) demonstrating exceptional crystallinity, thermal stability, and intense fluorescence. Three COFs—PP-COF, PT-COF, and PE-COF—were synthesized, showcasing large surface areas and robust thermal stability up to 400 °C. The fluorescence properties and intramolecular charge transfer within these COFs were significantly influenced by their Schiff base bonding types and π-stacking degrees between COF layers. Notably, PE-COF emerged as the most fluorescent among the three COFs and exhibited exceptional sensitivity and rapid response as a fluorescent chemosensor for detecting HCl in solution. The reversible protonation of imine bonds in these COFs allowed for the creation of highly sensitive acid vapor sensors, showcasing a shift in spectral absorption while maintaining structural integrity. This research highlights the potential of COFs as reliable and reusable sensors for detecting harmful acid vapors, addressing environmental concerns arising from industrial activities.

: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

Currently, the chemistry of conjugated nitrodienes is becoming more and more popular. These molecules are successfully applied in cycloaddition to synthesize six-membered rings in Diels-Alder reactions. Nitrodienes can be also applied to obtain bis-compounds in [3+2] cycloaddition. Moreover, the presence of a nitro group in the structure provides a possibility of further modification of the products. The simplest symmetrical representative of conjugated nitrodienes is (1E,3E)-1,4-dinitro-1,3-butadiene. Although the first mentions of the compound date back to the early 1950s, the compound has not yet been examined thoroughly enough. Therefore, in this article a comprehensive study of (1E,3E)-1,4-dinitro-1,3-butadiene has been described. For this purpose, an experimental study including synthesis process as well as spectral characteristic has been conducted. So as to better understand the properties of this compound a computational study of reactivity indices based on MEDT and also assessment of pharmacokinetics and biological activity according to ADME and PASS methodologies have been made. On this basis, some future application trends of (1E,3E)-1,4-dinitro-1,3-butadiene have been proposed.

The study focuses on the impact of new methods for inhibiting malolactic fermentation in white wines on their analytical and sensory properties. Enological preparations with different mecha-nisms of effect were tested: fumaric acid, chitosan, Estaan (a preparation based on tannin inhibi-tion), medium-chain fatty acids (MCFA), sulphur dioxide and a control variant where malolactic fermentation (MLF) was performed. The samples underwent analysis through HPLC (high-performance liquid chromatography) to determine concentrations of malic and lactic acid, as well as biogenic amines. GC (gas chromatography) analysis was used to monitor volatile sub-stances, alongside sensory evaluation. The study demonstrated a significant influence of indi-vidual enological preparations on the aromatic profile of the examined wines. The SO2 and MCFA variants exhibited the highest concentrations of volatile substances within the esters group, spe-cifically isoamyl acetate, 1-hexyl acetate and phenylethyl acetate. Conversely, the fumaric acid and Estaan variants displayed the lowest concentrations of these esters. The most notable disparities were observed in acetoin concentration, with the MCFA variant exhibiting the lowest values. Additionally, the chitosan variant showed higher concentrations of putrescine and spermidine compared to the MCFA and fumaric acid variants, which presented the lowest levels.

In this study, the pristine MgO, MgO/CNT and Ni-MgO/CNT nanocomposites were processed by the impregnation and chemical vapour deposition methods and analyzed for hydrogen evolution (HER) via electrochemical water splitting process. Furthermore, effect of nickel on the deposited carbon was systematically elaborated in this study. The highly conductive carbon nanotubes (CNTs) deposited on the metal surface of the Ni-MgO nanocomposite heterostructure provides the robust stability and superior electrocatalytic activity. The optimized Ni-MgO/CNT nanocomposite exhibited hierarchical helical-shaped carbon nanotubes adorned on the surface of the Ni-MgO flakes, forming a hybrid metal-carbon network structure. The HER catalytic reaction was carried out in 1M alkaline KOH electrolyte, and the optimized Ni-MgO/CNT nanocomposite achieves the low 117 mV overpotential value (ɳ) at the 10 mA cm-2 and needs low 116 mV/dec Tafel value denoted Volmer-Heyrovsky pathway. Also, high electrochemical active surface area (ECSA) value of Ni-MgO/CNT nanocomposite acquires 515 cm2, which is favorable for the generation of abundant electro-active species and the prepared electrocatalyst durability was also performed by chronoamperometry test for prolonged duration of 20 h at 10 mA cm-2 and exhibits the good stability with 72% retention. Hence, obtained results demonstrated that the optimized Ni-MgO/CNT nanocomposite is highly active and cost-effective electrocatalyst towards hydrogen energy production.

This work deals with a novel porous TiNi-based material for ophthalmic orbital implants that was produced by high-temperature synthesis (SHS) and possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

Titanium boride (TiB2) is a material classified as ultra-high temperature ceramics. The TiB2 structure is dominated by covalent bonds, which gives materials based on TiB2 very good mechanical and thermal properties, but also makes them difficult to sinter. Obtaining dense TiB2 polycrystals requires chemical or physical sintering activation. Carbon and molybdenum disilicide (MoSi2) were chosen as sintering activation additives. Three series of samples were made, the first with carbon additives: 0 to 4 wt.%; the second with 2.5, 5 and 10 wt.%. MoSi2 and the third with both additions of 2 wt.% carbon and 2.5, 5 and 10 wt.% MoSi2. MoSi2. On the basis of dilatometric sintering analysis, all additives were found to have a favourable effect on sinterability of TiB2, and it was determined that sintering of TiB2 with carbon addition can be carried at 2100°C and with MoSi2 and both additives at 1800°C. The polycrystals were sintered using the hot pressing technique. On the basis of the studies conducted in this work, it was found that addition of 1 wt.% of carbon allows to obtain single-phase TiB2 polycrystals of high density (>90%). The minimum MoSi2 addition required to obtain dense sinters with a cermet-like microstructure was 5 wt.%. High density was also achieved by materials containing both additives. Samples with higher MoSi2 content, i.e. 5 and 10% showed densities close to 100%. Mechanical properties such; as Young's modulus, hardness and fracture toughness (KIc) of the polycrystals and composites were similar for samples with densities exceeding 95%. The Vickers hardness was 23 to 27 GPa, the fracture toughness (KIC) was 4 to 6 MPa·m0.5 and the Young's modulus was 480 to 540 GPa. The resulting TiB2-based materials showed potential in high-temperature applications.

Flotation of small particles is one of the global challenges facing the mineral raw materials processing industry. Large amounts of non-ferrous and rare metals are lost in the flotation tailings in the form of mineral particles below 15 µm in size as a result of the low effectiveness of their capture by coarse bubbles generated in conventional flotation machines. The method of combined microflotation, which is being developed in recent years, uses not only coarse but also microbubbles (MB) produced in the stand-alone generator of air-in-water microdispersion, which serves as the flotation carriers. Depending on the dose of MB, the effect of their application may be both positive, but also negative. The theoretical analysis of various mechanisms of particle transfer onto the surface of coarse bubbles and further into the froth layer allowed to obtain the formula for the optimal MB dose f=2dddpρp, where dd is MB size; dp and ρp respectively are the size and the density of particles. Experiments performed on the copper ore flotation tailings at the Atalaya Mining (Spain) and Chaarat Kapan (Armenia) concentrators showed that, besides the optimal MB dose in the range of 1-3 ml/g, there is another optimal MB dose in the range of 10-20 ml/g, where the copper recovery increases by several percent compared to the reference test (f= 0). In the area between the optimal MB doses, the deep minimum in copper recovery is observed, which value is by several percent lower compared to the value in the reference test.

The feasibility of replacing the toxic chlorobenzene antisolvent with the environmentally friendly anisole in the fabrication of planar triple cation perovskite solar cells was explored. The successful integration of anisole not only ensures comparable device performance but also contributes to the development of more sustainable and green fabrication processes for next-generation photovoltaic technologies. Nevertheless, to ensure the possibility to achieve well-functioning unencapsulated devices, at any time of the year, with changed temperature and relative humidity, several batches with different cesium concentration were realized. We found that 10% of CsI in the precursor solution makes devices with low hysteresis index and sustained performance stability over a 90-day period both with cholorobenzene and anisole antisolvent. However the use of anisole as a green antisolvent ensures enhanced performance.

Natural polysaccharides, which are described in this study, are some of the most extensively used biopolymers in food, pharmaceutical and medical applications, because they are renewable and have a high level of biocompatibility and biodegradability. The fundamental understanding required to properly exploit polysaccharides potential in the biocomposite, nanoconjugate, and pharmaceutical industries is depended on detailed research of these molecules. Polysaccharides are preferred over other polymers because of their biocompatibility, bioactivity, homogeneity, and bioadhesive. Natural polysaccharides have also been discovered to have excellent rheological and biomucoadhesive properties, which may be used to design and create a variety of useful and cost-effective drug delivery systems. Polysaccharide-based composites derived from natural sources have been widely exploited due to their multifunctional properties, particularly in drug delivery systems and biomedical applications. These materials have achieved global attention and are in great demand because to their biochemical properties, which mimic both human and animal cells. Although synthetic polymers account for a substantial amount of organic chemistry, natural polymers play a vital role in a range of industries, including biomedical, pharmaceutical, and construction. As a consequence, the current study will provide information on natural polymers, their biological uses, food and pharmaceutical applications.Keywords: Polymers Biopolymers, Excipient, Natural source, Food and Pharmaceutical applications.

Metal halide perovskites have shown excellent optoelectronic properties, including high photoluminescence quantum yield, tunable emission wavelength, narrow full-width at half-maximum and low-cost solution-processed fabrication, which make it exhibit great potential as the emission layer materials of light emitting diodes. With the joint efforts of researchers from different disciplines, there has been a significant progress in the improvement of external quantum efficiency (EQE) and stability of perovskite light emitting diodes (PeLEDs) in recent few years, especially in green PeLEDs with EQE over 30%. In this review, we firstly introduce the basic device structure of PeLEDs, as well as the factors influencing EQE and stability of PeLEDs. Secondly, the development of lead-based and lead-free PeLEDs are summarized systematically. Thirdly, challenges of PeLEDs are discussed in detail, including low EQE of blue PeLEDs, poor device stability and EQE roll-off. Finally, some suggestions and perspectives of the future research directions for PeLEDs are proposed.

The microstructure evolution of SCM435 cold heading steel at different cooling rates was investigated by means of scanning electron microscopy, TEM, XRD, and electron backscatter diffraction. The results show that the cooling rate has a significant effect on the microstructure of the experimental steel. With an acceleration of the cooling, the microstructure of the steel gradually changed from ferrite and pearlite to ferrite, pearlite, and granular bainite; finally, the pearlite disappeared, and the microstructure changed to acicular ferrite, bainite, and martensite. With an increase in the cooling rate, the morphology of the carbide underwent an evolution from sheet carbide to short-rod carbide, granular carbide, and ultimately thin-strip carbide. With the acceleration of cooling, the proportion of large-angle grain boundaries gradually decreased, and the area of small-angle grain boundaries gradually increased. When the cooling rate was 0.1℃/s, the proportion of large-angle grain boundaries was as high as 52.8%, and the dislocation density was only 1.91 × 1012 cm−2. When the cooling rate was 2.0℃/s, the proportion of large-angle grain boundaries was only 27.1%, and dislocation density increased to 5.38 × 1012 cm−2. With the increase in the cooling rate, the depth of the decarbonization layer and the thickness of the scale oxide gradually decreased, the proportion of FeO phase in the scale phase gradually decreased, and the proportion of Fe3O4 phase and Fe2O3 phase gradually increased. The tensile strength increased monotonously with the increase in cooling rate, whereas the elongation and shrinkage first decreased, then increased, and then decreased. When the cooling rate was 1.0 m/s, the short rod and granular bainite in the material structure endowed the SCM435 steel with excellent strength and toughness matching, and the tensile strength and elongation of the steel reached 895 MPa and 24%, respectively.

In this work, nanocomposite photoelectrodes of the TiO2/ Au composition were manufactured, in which the size of plasmonic Au nanoparticles was varied, and the morphology of the TiO2 layer, depending on the thickness, changed from an island to a continuous layer. The influence of the morphology of plasmonic Au nanoparticles and the TiO2 layer on the optical and photoelectrochemical characteristics of hybrid photoelectrodes was studied. It has been shown that continuous coating of Au nanoparticles with a TiO2 layer (layer thickness 10 and 15 nm) leads to a decrease in the photoelectric response, and the decrease in photocurrent density and photoconversion efficiency decreases in proportion to the thickness of the TiO2 layer. The indicated drop in characteristics when plasmonic particles are located under the TiO2 layer is presumably associated with the scattering and recombination of charge carriers in the semiconductor layer. The best performance was shown by a system in which large Au nanoparticles (10 nm) are coated with a 5 nm thick layer of titanium dioxide; in this geometry, Au nanoparticles are decorated with TiO2 nanoparticles, as a result of which the photoelectrode-electrolyte interface has a more complex structure.

A series of polynuclear, dinuclear, and mononuclear Mo(VI) complexes were synthesized with the hydrazonato ligands derived from 5-methoxysalicylaldehyde and the corresponding hydrazides (isonicotinic hydrazide (H2L1), nicotinic hydrazide (H2L2), 2-aminobenzhydrazide (H2L3) or 4-aminobenzhydrazide (H2L4)). The metallosupramolecular compounds obtained from non-coordinating solvents, [MoO2(L1,2)]n (1 and 2) and [MoO2(L3,4)]2 (3 and 4), formed infinite structures and metallacycles, respectively. By blocking two coordination sites with cis-dioxo ligands, the molybdenum centers have three coordination sites occupied by the ONO donor atoms from the rigid hydrazone ligands and one by N atom of pyridyl or amine-functionalized ligand subcomponents from the neighbouring Mo building units. The reaction in methanol afforded the mononuclear analogues [MoO2(L1-4)(MeOH)] (1a-4a) with additional monodentate MeOH ligand. All isolated complexes were tested as catalysts for cyclooctene epoxidation using tBuOOH (TBHP) as an oxidant in water. The impact of the structure and ligand lability on the catalytic efficiency in homogeneous cyclooctene epoxidation was elucidated through theoretical considerations. Thus, dinuclear assemblies exhibited better catalytic activity than mononuclear or polynuclear complexes.

Diatomite (DME) consists of natural ordered porous structures that are excellent candidates as microcontainers. However, to the best of our knowledge, the application of DME loaded with corrosion inhibitors in anti-corrosion coatings has not hitherto been reported. In this study, DME has been used as a source of microcontainers to load benzotriazole (BTA) inhibitor by an immersion method. In order to prevent unwanted early release of the small molecule BTA inhibitor from the DME microcontainers, inspired by the adhesion characteristics of catechol and amine in mussel adhesion protein, polydopamine (PDA) was coated on their surfaces to generate BTA@DME/PDA microcapsules. Because of the depolymerization characteristics of PDA at low pH, the synthesize microcapsules showed a controllable release function. The SEM morphology, chemical structure, and loading capacity of the synthesized BTA@DME/PDA microcapsules were characterized. The corrosion resistances of epoxy coatings with different contents of BTA@DME/PDA microcapsules were compared by saline immersion and electrochemical impedance tests. A scratched coating with 5wt.% BTA@DME/PDA microcapsules showed the best anti-corrosion effect.

Increased CO2 emissions and air pollution impact the environment and human health. In this manner, new functionalized polyaminal-based polymers are synthesized via a one-pot polycondensation reaction of melamine with aldehyde monomers 2-bromo-1-naphthaldehyde and 2-hydroxy-1-naphthaldehyde to yield bromine- hydroxyl- functionalized polymer networks PAN-BrNA and PAN-HNA, respectively. The polyaminals porosity parameters were investigated and applied as an adsorbent for CO2 capture. FTIR, solid-state 13C NMR, and X-ray diffraction verified the PANs structure development. A scanning electron microscope and N2 adsorption-desorption methods were utilized to identify the porous properties of the polymers at 77 K. The Brunauer-Emmett-Teller (BET) surface area of PAN-BrNA and PAN-HNA is (16.6990 m2/g) and (716.7568 m2/g), respectively. At 273 K, PAN-BrNA and PAN-HNA can take CO2 gas up to (4.42786 cm3/g) and (47.55 cm3/g), respectively. The findings show that inserting functional groups has a significant impact on surface area and porosity parameters, as well as CO2 uptake.

A series of polyacrylonitrile (PAN)-based block copolymers with poly(methyl methacrylate) (PMMA) as sacrificial bock were synthesized by atom transfer radical polymerization and used as precursors for the synthesis of porous carbons. The carbons enriched with O- and S-containing groups, introduced by controlled oxidation and sulphuration, respectively, were characterized by Raman spectroscopy, scanning electron microscopy, and X-ray photoelectron spectrometry, and their surface textural properties were measured by a volumetric analyzer. We observed that the presence of sulphur tends to modify the structure of the carbons, from microporous to mesoporous, while the use of copolymers with a range of molar composition PAN/PMMA between 10/90 to 47/53 allows the obtainment of carbons with different degrees of porosity. The amount of sacrificial block only affects the morphology of carbons stabilized in oxygen, inducing their nanostructuration, but has not effect on their chemical composition. We also demonstrated their suitability for separating a typical N2/CO2 post-combustion stream.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The study involved two brominated molecules, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 and NBS under IR irradiation at 120 Watts of potency and dichloromethane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis show the occurrence of a Z to E con-formational change. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds.

Doping can alter the electronic and thermoelectric attributes of an organic semiconductor system. These alterations can enable viable tunable devices that have applications in temperature sensing for environmental controls. Here we demonstrate a dual-modulation organic field-effect transistor (OFET) where temperature effectively modulates the current-voltage characteristics of the OFET and gate voltage modulates the thermoelectric properties of the active layer. Poly(3-hexylthiophene-2,5-diyl) (P3HT) was utilized as the host donor polymer, iodine was utilized as the dopant acceptor molecule Finished devices were characterized by a semiconductor analyzer system with temperature controlled by two thermoelectric cooling plates. The doping of iodine in the range of 0.25% to 0.5% mole ratio with respect to the P3HT exhibited the greatest on-off ratio of the investigated dopant concentrations. Iodine doping concentrations of 0.5% mole ratio or less can greatly improve the thermoelectric properties of a binary P3HT-based system and the current-voltage performance of the dual-modulation device.

Geijera Schott is a plant genus of the Rutaceae Juss. (rue and citrus) family, comprising six species which are all native to Oceania. Of the plants belonging to this genus, the most significant species that has a customary use is Geijera parviflora, which was used by Indigenous Australians, primarily as a pain reliever. Herein, a comprehensive review of the literature published on the genus Geijera from 1930-2023 was conducted. This is the first review for this plant genus and it highlights the chemical constituents reported to date, together with the range of pharmacological properties described from the various species and different parts of the plant. These properties include anti-inflammatory, anti-microbial, anti-parasitic, insect repellent, analgesic, neuroactive, and anti-cancer activities. Finally, a reflection on some of the important areas for future focused studies of this plant genus is provided.

The reduction of Ce cations in CeO2 can be enhanced by its partial substitution by Fe cations. The enhanced reduction of Ce cations results in a considerable increase in the reaction rates for thermal water splitting reaction when compared to CeO2 alone. This mixed oxide has a smaller crystallite size when compared to CeO2 in addition to a smaller lattice size. In this work, two Fe-substituted Ce oxides are studied (Ce0.95Fe0.05O2 and Ce0.75Fe0.25O2) by core and valence level spectroscopy in their as-prepared and Ar-ions sputtered states. Ar-ions sputtering substantially increases Ce4f lines at about 1.5 eV below the Fermi level. In addition, it is found that the XPS Ce5p/O2s ratio is sensitive to the degree of reduction, most likely due to a higher charge transfer from the oxygen to Ce ions upon reduction. Quantitatively it is also found that XPS Ce3d of the fraction of Ce3+ (uo, u’ and vo, v’) formed upon Ar-ions sputtering and the ratio Ce5p/O2s lines are higher for reduced Ce0.95Fe0.05O2 than for reduced Ce0.75Fe0.25O2. XPS Fe2p showed however no preferential increase for Fe3+ reduction to Fe0 with increasing time for both oxides. Since water splitting was higher on Ce0.95Fe0.05O2 when compared to Ce0.75Fe0.25O2, it is inferred that the reaction centers for the thermal water splitting to hydrogen are the reduced Ce cations and not the reduced Fe cations. These reduced Ce cations can be tracked by their XPS Ce5p/O2s ratio in addition to the common XPS Ce3d lines.

Single-fluid electrospinning creates nanofibers from molten polymer solutions with active ingredients. The study utilized a combination of a fractional factorial design and a Box-Behnken design to examine crucial factors among a multitude of parameters and to optimize the electrospinning conditions that impact the fiber mats' morphology and entrapment efficiency of the Senna alata leaf extract. The findings indicated that the shellac content had the greatest impact on both fiber diameter and bead formation. The optimum electrospinning conditions were identified as a voltage of 24 kV, a solution feed rate of 0.8 mL/h, and a shellac-extract ratio of 38.5:3.8. These conditions produced nanosized fibers with a diameter of 306 nm, a low bead-to-fiber ratio of 0.29, and an extract entrapment efficiency of 96% within the fibers. The biphasic profile of optimized nanofibers was confirmed through an in vitro release study. This profile consisted of an initial burst release of 88% within the first hour, which was succeeded by a sustained release pattern surpassing 90% for the next 12 h, as predicted by zero-order release kinetics. The optimized nanofibers demonstrated antimicrobial efficacy against diverse pathogens, suggesting promising applications in wound dressings and protective textiles.

In this study, we report a novel synthesis of hydrophobic silica aerogel powder composites, functionalized and binary-doped with [Tb(phen)₂](NO₃)₃ and [Eu(phen)₂](NO₃)₃ nanocrystals, employing a two-step sol-gel methodology. The investigation delves into the structural elucidation, optical properties and thermal conductivity of these functionalized Tb(III)-Eu(III) composites. Our analysis encompasses diffuse reflectance spectra, along with excitation and luminescence spectra, highlighting the quantum yields of composites with varying chemical composition. Remarkably, these samples exhibit a strong luminescence, with distinct hues of red or green color upon the specific doping type and level. The detailed examination of excitation spectra and quantum yields unequivocally establishes robust energy transfer mechanisms from the 1,10-phenanthroline molecule to the lanthanide ions. Notably, our study uncovers a Tb³⁺→Eu³⁺ energy transfer phenomenon within the binary functionalized samples, providing compelling evidence for a structural formation process occurring within the mesoporous framework of the aerogel powders.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

Sunscreens are topical preparations containing one or more compounds that protect humans from ultraviolet (UV) light. This review focuses on analytical methods, particularly liquid chromatography, aimed at identifying and determining UV filters (UVFs) in environmental and marine biota matrices. A literature review was done using NIH (PubMed and Medline), FDA and EPA databases, Google Scholar, and Federal Regulations. This retrospective literature review is focused on the last five years. UVFs quantification in environmental and biological matrices showed a wide array of methods where liquid chromatography is predominant. The scientific literature identified a large variety of analytical methodologies that are compared in this review, to evaluate the better results in terms of limits of quantification and the possibility to identify as many analytes as possible simultaneously.

NiO-based nanomaterials have attracted a great deal of interest in view of various applications, that have stimulated the implementation of various synthetic approaches to control their chemico-physical properties as a function of the desired end-use. In this regard, their bottom-up preparation starting from suitable precursors plays an important role, but a molecular level in-sight into their reactivity remains an open challenge. In this study, we focus on the fragmentation of Ni(II) diketonate-diamine adducts, of interest as precursors for Ni(II) oxide systems, by com-bined electrospray ionization mass spectrometry (ESI-MS) with multiple collisional experiments (ESI-MSn) and theoretical calculations. The joint analyses revealed common features in the frag-mentation pattern of the target compounds: i) in the first-fragmentation, all three complexes form analogous base-peak cations by losing a negatively charged diketonate; in these cations, Ni-O and Ni-N interactions are stronger and the Ni positive charge is lower than in the neutral complexes; ii) the tendency of ligand electronic charge to migrate towards Ni further increases in the subsequent fragmentation processes, leading to the formation – in all three cases – of a tetracoordinated Ni environment involving an interesting cation-π intramolecular interaction.