The research aims to resolve water pollution generated by dye wastewater. In this paper, the aminated sodium lignosulfonate (AELS) was prepared through the Mannich reaction, and the synthesis conditions were optimized using orthogonal experiments to determine the best amination conditions. The successful preparation of AELS was demonstrated through the use of FT-IR, XRD, TG, SEM and XPS characterization techniques. Then, the adsorption capacity of Methyl blue (MB) by AELS was compared in a range of different circumstances, like pH, adsorbent dose, initial concentration, time, and temperature. Additionally, the kinetics, isotherms, and thermodynamic properties of the AELS adsorption for MB were studied and discussed. The results indicated that the fitting results were consistent with the pseudo-second-order kinetic model and Langmuir isotherm model, in accordance with the mechanism of single-molecular-layer chemisorption. And the adsorption of MB by AELS was a spontaneous and endothermic process. Upon completion of five adsorption experiments, the adsorption capacity of MB by AELS was determined to be 107.95 mg g-1, which was 5.3% lower than the first experiment. This research promotes the effective use of natural resources and allows for the sustainable use of lignin and the advancement of new applications for it.

There is a growing demand and use of herbal cosmetics for skin purposes due to their perceived safety when applied to the skin. Three Cassipourea species commonly known as “ummemezi” are used interchangeable by women in rural areas of Eastern Cape and KwaZulu-Natal provinces to treat hypermelanosis as well as sun protection. We conducted a phytochemical comparison of three Cassipourea species; C. flanaganii, C. gummiflua and C. malosana by LC-MS/MS analysis in negative mode. The results obtained from the LC-MS/MS yielded a total number of twenty-four compounds of different chemical classes, including fatty acids, steroids, di- and tri-terpenoids, flavonoids, phenolic acids were detected, and eighteen among them were tentatively identified. Despite the recent popularity of modern cosmetic products, it is clear that plants continue to play an important role in the local cosmetics industry in South Africa's Eastern Cape and KwaZulu-Natal community provinces. The findings of this study suggest that an alternative treatment for hyper-melanosis disorders should be developed further. The residual wild plant stocks are insufficient to meet commercial needs, thus, encouraging their sustainable use is a means of harnessing the conservation of these plants. Indigenous communities should be supported in the commercialization which could be linked to the rural economic development.

The recent advancements in communication technology have facilitated the widespread deployment of electronic communication equipment globally, resulting in the pervasive presence of electromagnetic pollution. Consequently, there is an urgent necessity to develop a thin, lightweight, efficient, and durable electromagnetic interference (EMI) shielding material, capable of withstanding severe environmental conditions, and possessing a scalable production method. In this paper, we proposed an innovative and scalable method for preparing EMI shielding films with a tunable sandwich-structure. The film possesses a nylon mesh (NM) backbone, with AgNWs serving as the shielding coating and aramid nanofibers (ANFs) acting as the cladding layer. The prepared film was thin and flexible, with a thickness of only 0.13 mm. AgNWs could easily form a conductive network structure with excellent performance, and the film had a high EMI shielding efficiency, up to 50.6 dB with 1.0mg/cm2. Due to the outstanding thermal resistance, acid and alkali resistance properties of aramid fibers, the NAAANF film demonstrates remarkable robustness in the face of complex usage environments. Such a thin, efficient and environmentally resistant EMI shielding film provided new ideas for the broad EMI shielding market.

Advances in biomimetic triboelectric nanogenerators (TENGs) have significant implications for electronic skin (e-skin) and human-machine interaction (HMI). Emphasizing the need to mimic complex functionalities of natural systems, particularly human skin, TENGs leverage triboelectricity and electrostatic induction to bridge the gap in traditional electronic devices' responsiveness and adaptability. The exploration begins with an overview of TENGs' operational principles and modes, transitioning into structural and material biomimicry inspired by plant and animal models, proteins, fibers, and hydrogels. Key applications in tactile sensing, motion sensing, and intelligent control within e-skins and HMI systems are highlighted, showcasing TENGs' potential in revolutionizing wearable technologies and robotic systems. This review also addresses the challenges in performance enhancement, scalability, and system integration of TENGs. It points to future research directions, including optimizing energy conversion efficiency, discovering new materials, and employing micro-nanostructuring techniques for enhanced triboelectric charges and energy conversion. The scalability and cost-effectiveness of TENG production, pivotal for mainstream application, are discussed along with the need for versatile integration with various electronic systems. The review underlines the significance of making bioinspired TENGs more accessible and applicable in everyday technology, focusing on compatibility, user comfort, and durability. Conclusively, it underscores the role of bioinspired TENGs in advancing wearable technology and interactive systems, indicating a bright future for these innovations in practical applications.

A rapid and efficient technique using an electronic nose based on a mass detector combined with headspace sampling (HS-SPME-MS e-nose) and chemometric tools was applied to classify beer samples between fresh and aged and between samples contained in aluminium cans or glass bottles, and to predict the shelf life of beer. The mass spectra obtained from the HS-SPME-MS e-nose contain information on the volatile compounds, recorded as the abundance of each ion at different mass-to-charge (m/z) ratios. The analysis was performed on 53 samples aged naturally for eleven months in the absence of light and with a controlled temperature of around 14° C +/- 0.5° C. Principal Component Analysis (PCA) was performed on the data, showing a grouping of samples between fresh and aged. Partial Least Square Discriminant Analysis (PLS-DA) allowed discriminating fresh from aged beers but was not able to discriminate samples packaged in aluminium cans or in glass bottles. Finally, Partial Least Square Regression (PLSR) was applied to build a prediction model and showed to be effective to predict beer shelf life.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

We have recently reported that a series of 1,3,4-oxadiazol-2-ylbenzenesulfonamides acts as potent and specific monoamine oxidase B (MAO-B) inhibitors with some compounds possessing potencies in the nanomolar range. While sulfonamide compounds (e.g., zonisamide) have been reported to inhibit the MAO enzymes, nanomolar MAO inhibition potencies for this class are not frequently observed. The present study expanded on these findings by replacing the 1,3,4-oxazole moiety with a 1,3-thiazole heterocycle. A series of 23 primary sulfonamides were synthesized by reaction of an α-haloketone with a substituted carbothioamide. The results of the MAO inhibition studies showed that the 1,3-thiazolylbenzenesulfonamides were specific inhibitors of human MAO-B. The most potent MAO-B inhibitor exhibited an in vitro IC50 value of 0.103 µM (3j). The derivatives were, however, weaker inhibitors of human MAO-A with the most potent compound exhibiting an IC50 value of 11.9 µM (3a). Examination of the structure-activity relationships (SARs) showed that the most potent MAO-B inhibition was obtained with substitution of the sulfonamide on the meta position of the phenyl rather than the para position. This study concludes that 1,3-thiazolylbenzenesulfonamides represent a class of potent and specific MAO-B inhibitors, which may serve as leads for the development of new treatments for disease states such as Parkinson’s disease.

The usability of glass fibers as immobilization support with porous open structure has been explored. We have developed a method for immobilization of β-galactosidase on special glass fiber rolls. The new method provides a simple, non-expensive and industrially applicable method. Glutaraldehyde was used as a non-specific crosslinking agent for covalent binding of β-galactosidase on modified glass fibers. The efficiency of immobilization was tested with the known hydrolysis of lactose. All experiments were performed in a continuous laboratory reactor. The effect of reaction temperature (20, 25, and 30) °C, substrate flow rate (1, 2, and 3) mL/min, and pH of the reaction medium (6, 7, and 8) on the conversion was studied. The reaction efficiency was monitored by measuring the glucose concentration with a spectrophotometer. High immobilization efficiency and enzyme activity and stability were obtained. The optimum reaction temperature, substrate flow rate and pH were found. The activity and stability of the enzyme entrapped on the glass fiber rolls remained almost unchanged during reuse, which is a good prospect for potential industrial applications.

Porous structures and micropatterning surfaces play a crucial role in the development of highly sensitive force sensors. However, achieving these two conductive architectures typically requires complex materials synthesis and expensive manufacturing processes. In this study, we introduce a novel conductive composite film featuring a porous/micropyramid hybrid conductive architecture, which is achieved through a straightforward process of materials mixing and one-step screen printing. By utilizing a deep eutectic solvent in the ink component, micropores are induced in the printed composite, while the mesh of the screen mask acts as a template, resulting in a micropyramid film surface. We have successfully realized highly sensitive flexible force sensors with multifunctional capabilities for perceiving normal force and shear force.

A unique method for synthesizing a surface modifier for metallic hydrogen permeable mem-branes based on non-classic bimetallic pentagonally structured Pd-Pt nanoparticles has been de-veloped. It was found that nanoparticles had unique hollow structure. This significantly reduces the cost of their production due to economical use of metal. According to the results of electro-chemical studies, synthesized bimetallic Pd-Pt/Pd-Ag modifier showed excellent catalytic activi-ty (up to 60.72 mA cm–2), long-term stability and resistance to COads poisoning in alkaline oxida-tion reaction of methanol. The membrane with pentagonally structured Pd-Pt/Pd-Ag modifier showed the highest hydrogen permeation flux density up to 27.3 mmol s–1 m–2. Obtained hy-drogen flux density were 2 times higher than that for membranes with classic Pdblack/Pd-Ag modifier and an order of magnitude higher than that for unmodified membrane. Since the rate of transcrystalline hydrogen transfer through a membrane increased, while the speed of transfer through defects remained unchanged, a one and a half times rise in selectivity of the developed Pd-Pt/Pd-Ag membranes was recorded and it amounted to 3514. Achieved results are due to both the synergistic effect of the combination of Pd and Pt metals in the modifier composition and the large number of available catalytically active centers, which are present as a result of non-classic morphology with high-index facets. The specific faceting, defect structure and unusual properties provide great opportunities for the application of nanoparticles in the areas of membrane reac-tors, electrocatalysis, petrochemical and hydrogen industries.

Organic electrochemical transistors (OECTs) based on conducting polymers have attracted significant attention in the field of biosensors. PEDOT:PSS and polyaniline (PANI) are representative conducting polymers used for OECTs. While there are many studies on PEDOT:PSS, there are not so many reports on PANI-based OECTs, and a detailed study to compare these two polymers has been desired. In this study, we investigated the fabrication conditions to produce the best performance in the OECTs using the above-mentioned two types of conducting polymers. Two main parameters were film thickness and film surface roughness. For PEDOT:PSS, the optimal conditions for fabricating thin films were a spin-coating rate of 3000 rpm and DI water immersion time of 18 hours. For PANI, the optimal conditions were a spin-coating rate of 3000 rpm and DI water immersion time of 5 seconds, and adding dodecylbenzenesulfonic acid (DBSA) was found to provide better OECT performances. The OECT performances based on PEDOT:PSS were superior to those based on PANI in terms of conductivity and transconductance, but PANI showed excellence in terms of film thickness and surface smoothness, leading to the good reproducibility of OECT performances.

Phyllanthus emblica (P. emblica) has been described in many studies to have multiple therapeutic activities and is considered an important part of Ayurvedic and Unani medicinal systems. This study successfully synthesized P. emblica loaded polyvinylalcohol/gelatin based cryogels (PVA/Gel/P.emblica) to examine their potential in wound dressing applications. Swelling tests, Brunauer-Emmett-Teller (BET) and morphology analysis were conducted within the scope of characterization studies. In vitro cell culture studies were performed using HaCaT cells to illustrate the suitability of the synthesized cryogels as wound dressing material. The swelling tests and BET analysis results showed that swelling and surface area properties of cryogels increased with increasing P. emblica amounts. Morphological results displayed that the cryogels had a dense, interconnected pore morphology and a macroporous structure. 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT), trypan blue exclusion and live-dead assay results revealed that adding of P. emblica into cryogels led to enhanced cell proliferation, increased cell number, and improved cell viability. Based on the phase contrast microscope, scanning electron microscope (SEM), immunofluorescence and giemsa staining images, it was observed that P. emblica promoted cell attachment, proliferation and penetration. In conclusion, it has been shown that PVA/Gel/P.emblica cryogels are suitable for use as wound dressing materials and can be developed with further studies.

Elevated ammonium (NH4+) concentrations in untreated waterways contribute to eutrophication and dissolved oxygen depletion, which cause severe degradation of water quality. Ion exchange processes are a robust, low operational cost and efficient option for ammonium removal with zeolites being the most widely used. Geopolymers are a sustainable and low-cost option compared to zeolites that follows the same ion exchange technology. In the present study, a metakaolin-based porous geopolymer was synthetized, characterised and validated as adsorbent material. The laboratory batch tests showed a maximum adsorption capacity (Qm) of 18.35 mg/g being 27% higher than reference zeolites. Kinetics followed the Weber-Morris rate equation being the intraparticle diffusion the limiting process and continuous experiments indicated a maximum removal of 97% in the first hours. The material was validated in a wastewater treatment pilot plant where values in pH, electrical conductivity and NH4+ concentration were monitored. The obtained data indicated that the material achieved up to 80% NH4+ removal which is similar to traditional zeolites. The results demonstrate that this sustainable, low-cost and easy-to-install metakaolin-based geopolymer can be used effectively for NH4+ treatment.

The structural evolution and phase composition of multi-block thermoplastic polyurethanes, with different nature of the soft segments based on poly(butylene adipate) (PBA), were analyzed during in-situ thermal treatments. A combination of synchrotron small- and wide-angle X-ray scattering, differential scanning calorimetry, thermogravimetric analysis, and FTIR spectroscopy was used to determine the influence of macrodiol nature and crystallization conditions on the polymorphic behavior of PBA. Using a new synthesis scheme, a relatively high degree of crystallinity for urethane blocks was achieved, which depends on the diisocyanate type in the structure of the soft segment. The hard segment domains impose geometrical constraints on PBA, thereby altering its crystallization process compared to the neat oligomer. Thus, crystallization after annealing at a low temperature (80 °C) is fast, predominantly yielding a metastable β-phase. When heated to 180 °C, which is higher than the hard-segment melting temperature, a phase-separated structure is observed. Subsequent crystallization is slower, favoring the formation of the stable α-PBA modification. The phase separation can be observed even after the hard block melting. A notably slow crystallization from an isotropic melt was documented after the disruption of phase separation at 230 °C.

The steady state tube furnace (SSTF) (ISO/TS 19700) was used to assess the effects altering the reaction zone of a flame had on smoke toxicity measurements. The gas inlet of the apparatus was modified to allow for a mixture of nitrogen and air to be introduced into the system. The volume of air used in each test remained at 2 L min-1 , and additional volumes of nitrogen were varied between tests altering the total volume of gas used in the primary gas inlet. The chosen conditions were representative of under-ventilated flaming by using a restricted oxygen environment. The research shows that the increase in volume flow of gas over a sample increased the smoke toxicity of the materials tested (CO and HCN). When increasing the volume of the primary air-flow through the tube furnace, the flow causes thinning of the flame zone in the apparatus and results in gaseous species spending less time in the reaction zone, resulting in less time available for chemical reactions to occur. This resulted in less complete combustion occurring, and hence an increased yield of measured products of incomplete combustion (CO and HCN), and a decreased yield of products of complete combustion (CO2).

Biocomposite membranes based on polylactic acid (PLA) and cellulose nanocrystals (CNCs) were developed using a scientific approach. Dicumyl peroxide (DCP) was used as a polymerization ini-tiator, while tin octoate (Sn(Oct)2) and triphenylphosphane (P(C6H5)3) were used as catalysts. A torque rheometer was used to mix the components of the biocomposite, and thin films was prepared by solvent casting. Fourier transform infrared (FTIR) spectroscopy confirmed the coupling between the PLA and CNCs. Field emission scanning electron microscopy (FESEM) showed that the CNCs were well-dispersed in the PLA matrix with an unimodal particle size distribution and a maximum particle size of around 200 nm. Thermogravimetric analysis (TGA) and differential scanning calo-rimetry (DSC) analysis demonstrated good thermal stability and improved biodegradability of the biocomposite membrane compared to pure PLA. Mechanical characterization showed a Young's modulus of 1.65 GPa, which is comparable to that of other composite materials, and a maximum tensile strength of 20.31 MPa, which is higher than that of pure PLA. These results suggest that the developed biocomposite membrane has potential applications in water filtration, food packaging, and biomedical devices.

The leaf essential oils from five Eucalyptus spp.: E. astringens, E. camaldulensis, E. lehmanii, E. leucoxylon and E. sideroxylon growing in the same plantation area and conditions (plants with the same age and subjected to the same agronomic practices) were analyzed and evaluated for their antimicrobial activity. The essential oil yields ranged from 0.14 to 0.96% (w/w), and their chromatographic profiles were resolved into 48 compounds; among them, 11 were common to all essential oils. Terpenoids (oxygenated mono, and sesquiterpenes) dominated (55.66-76.67%) the oil profiles. Although 1,8-cineole (21.97-50.93%) was found as the main oxygenated monoterpene in all examined essential oils, principal component analysis observed and confirmed an interspecific chemical variability. Additionally, a set of distinctive chemical markers that could serve as a reliable tool for discrimination of Eucalyptus species and for authentication and quality control purposes (for commercial samples) has been defined for each essential oil. The antimicrobial disc-diffusion assay results revealed that all essential oils were endowed with a strong antimicrobial activity, with those derived from E. camaldulensis, E. lehmanii and E. leucoxylon being the most active.

Advancements in 3D printing technologies have led to new implementations in rapid prototyping, microfluidics, tooling, dentistry, biomedical devices, drug delivery, and tissue engineering. Stereolithography techniques, which are photopolymerization-based processes, contribute to the optical, chemical, and mechanical properties of 3D printed materials using versatile polymer chemistry. This study used potassium titanate powder (K2Ti8O17) as an additive to enhance the mechanical strength of photocurable resins. PEG was selected as the stabilizer to optimize the dispersion and precipitation of potassium titanate. The flexural strength, hardness, and tensile strength were compared to assess the mechanical strength of the 3D printing resin. The flexural strengths of the printed specimens were in the range of 15–39 N/mm2. The measured surface hardness and tensile strength were 41–80 HV and 2.3–15 N/mm2, respectively. The output resolution of the potassium titanate/acrylate resin was tested using a line-pattern structure. 3D printing resin without stabilizers produced lines with a thickness of 0.3 mm, whereas 3D printing resin containing a stabilizer produced lines with a thickness of 0.2 mm. The flexural strength and pattern thickness results suggest that the potassium titanate/acrylate resin can be utilized as a 3D printer resin, suggesting new possibilities for potassium titanate materials.

Self-compacting concrete (SCC) is a high-quality construction solution combining high fluidity, passing and filling ability with improved mechanical properties and durability. In the present study, the effect of incorporating alternative waste materials, such as two by-products of the ce-ment industry, namely cement kiln dust (CKD) and by-pass dust (BPD), into SCC as partial re-placement for traditional filler material was investigated. The produced compositions were compared with reference mixtures containing only marble powder (MP) as a filler. A series of tests including specific test methods for wet SCC, compressive, flexural and tensile splitting strength tests as well as drying shrinkage determination were conducted to evaluate the quality of the produced SCC in terms of fresh and hardened SCC properties. The use of alternative fine filler materials resulted in a high-performance sustainable SCC of low cement content. Specifi-cally, incorporating CKD into the SCC enhanced its rheological behavior and improved slightly its mechanical properties, while the use of BPD led to SCC mixtures of adequate rheological characteristics but with highly upgraded mechanical and physical properties

We successfully fabricated Ag@Cu2O core-shell decorated on reduced graphene oxide (rGO) nanocomposites (ACRN) by a simple and convenient in situ substitution method. The properties of these ACRN with heterostructure layers were characterized by scanning and transmission electron microscopies and absorption spectroscopy. We used p-nitrophenol (4-NP) as a probe molecule to determine the chemical catalytic activity of the ACRN. Upon introduction of rGO, a high electron transfer efficiency was achieved; thus, the catalytic activity was improved significantly. Therefore, the ACRN exhibited significantly improved catalytic activity for the reduction of 4-NP and showed the high application value in the removal of toxic and harmful substances from water. In addition, the fabricated ACRN was used for the reduction of organic dyes and explosive pollutants to generate nontoxic products. Furthermore, the high charge redistribution and transfer among Ag, Cu2O and rGO in the ACRN induced the high catalytic reduction of organic pollutants, indicating the excellent potential of these materials for applications in water pollution treatment.

Sulfolane, a highly water-soluble industrial solvent, has raised environmental concerns due to its persistence once released into the environment. To assess the extent of contamination effectively, reliable analytical methods are essential. In this review, we delve into the published literature on sulfolane analytical procedures. Existing guidelines for sampling from environmental matrices provide a solid foundation for sul-folane analysis. Notably, there is little variation in the choice of determination method, with GC-MS or GC-FID being favored across studies. However, substantial variability emerges in sample prep-aration methods. Many procedures rely on large quantities of environmentally hazardous solvents, such as dichloromethane, during extraction. Nevertheless, by incorporating extraction enhancement techniques proposed in various studies, it is possible to develop more eco-friendly extraction processes. Overall, this field calls for further re-search to devise efficient and environmentally sustainable analytical methods for sulfolane analysis. Through this review, insights into the challenges at hand and potential solutions can be gained, offering a foundation for the development of novel sulfolane analysis methods applicable to a range of environmental matrices.

Biocomposite membranes based on polylactic acid (PLA) and cellulose nanocrystals (CNCs) were developed using a scientific approach. Dicumyl peroxide (DCP) was used as a polymerization ini-tiator, while tin octoate (Sn(Oct)2) and triphenylphosphane (P(C6H5)3) were used as catalysts. A torque rheometer was used to mix the components of the biocomposite, and thin films was prepared by solvent casting. Fourier transform infrared (FTIR) spectroscopy confirmed the coupling between the PLA and CNCs. Field emission scanning electron microscopy (FESEM) showed that the CNCs were well-dispersed in the PLA matrix with an unimodal particle size distribution and a maximum particle size of around 200 nm. Thermogravimetric analysis (TGA) and differential scanning calo-rimetry (DSC) analysis demonstrated good thermal stability and improved biodegradability of the biocomposite membrane compared to pure PLA. Mechanical characterization showed a Young's modulus of 1.65 GPa, which is comparable to that of other composite materials, and a maximum tensile strength of 20.31 MPa, which is higher than that of pure PLA. These results suggest that the developed biocomposite membrane has potential applications in water filtration, food packaging, and biomedical devices.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Cathode materials based on SrCoO3- perovskite-type oxides hold great potential, given the huge oxygen permeability exhibited by the cubic phase of this oxide, which must be stabilized though suitable cationic substitutions. We present here two novel materials of the series Sr1-xYxCoO3- (x= 0.1, 0.2), prepared by solid state reactions. The crystalline structure was explored by neutron powder diffraction. At RT, we identified a subtle tetragonal superstructure, yet preserving the wanted framework of vertex-sharing CoO6 octahedra. A noteworthy result of the neutron analysis is the presence of conspicuous amounts of oxygen vacancies, ordered in layers and responsible for the formation of the mentioned superstructure. The stability was investigated by thermal analysis, using thermogravimetry (TGA). The electrical conductivity gave a maximum value of 800 °C of 122 S·cm–1. To determine the resistance associated with the oxygen reduction reaction (ORR), electrochemical impedance spectroscopy as a function of temperature was carried out, finding a value for the activation energy of Ea= 0.82 eV. This is a much lower value than that usually obtained for cathodes with a high catalytic activity for the oxygen reduction reaction. In single-cell tests, the materials generated a power density up to 0.25 Wcm−2 at 800ºC, using pure H2 as fuel. All these features make this perovskite a suitable candidate as cathode material in intermediate-temperature SOFCs

As both governments and customers push for sustainable and recyclable textile products, textile companies will have to change their linear business model to a circular one. The aim of the present work is to help these companies take action by providing an update of the state-of-the-art of textile recycling technologies. Extensive desktop research was performed in order to prepare an overview of existing textile recycling technologies, their current state and prognosis, including also facilitating technologies for sorting and disintegration of textile products as well as virtual platforms that connect stakeholders and inform consumers.

Redox-flow batteries are rechargeable batteries that store energy in two liquid electrolytes, separated by a membrane. During charging and discharging, the electrolytes flow through the membrane and undergo chemical reactions that generate or consume electrical energy. These batteries are known for their scalability and long cycle life and are versatile energy storage technologies developed to enhance efficiency and lower costs. Deep Eutectic Solvents (DES) are eco-friendly alternatives to traditional electrolytes, and their properties have been studied to improve the performance of redox-flow batteries. We investigated choline chloride/ethylene glycol (ChlCl/Eg) mixtures with LiPF6 salt at four concentrations through experimental and MD simulations. The thermophysical and transport properties of the mixture, including density, diffusion coefficient, viscosity, and ionic conductivity, were calculated across a temperature range of 298.15–398.5 K. Our findings indicate that an increase in salt concentration leads to a decrease in diffusion coefficients and ionic conductivity, while increasing the viscosity of the deep eutectic solvent. This research provides valuable insights into the behavior of DES mixtures and can aid in the design and optimization of DES-based processes for use in redox-flow batteries.

Smoked cigarette butts (SCB) can be used as precursors to obtain activated carbon (AC) due to their high carbon content related to the presence of cellulose acetate and components that are retained in the tobacco combustion process. In this way, it was analyzed how the process of pyrolysis or formation of char from this residue occurs, for this a study of the kinetics of formation of char is carried out by thermogravimetry, using three heating speeds 5, 10 and 15 °C/min. Based on the data obtained, mathematical models such as Kissenger - Akahira - Sunose (KAS), Starink (STK) and Ozawa - Flynn - Wall (OFW) were used in order to identify thermodynamic parameters through the energy of activation. The char obtained was subjected to an activation treatment with KOH in order to increase the surface area and pore volume, obtaining values of 433 m2/g of BET area and 0.25 cm3/g of micropore volume. Finally, the adsorbent was applied in the removal of Cr (VI) obtaining a Qmax capacity determined by the Langmuir model of 55.8 mg/g.

The (Ti, Nb)(C, B)/IN625 composite coating with both homogeneous and defect-free microstructure were successfully prepared by in situ on the surface of 42CrMo steel using the coupling of the ultra-high-speed laser cladding (EHLA in German) technology with the direct reaction synthesis (DRS) technology, and were comparatively analyzed with the IN625 coating prepared by the EHLA. The microstructure of the fused cladding layer was investigated by selected scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and double spherical aberration transmission electron microscopy (DSA-TEM). The residual stress distribution on both sides of the fused cladding interface was characterised by nanoindentation stress test based on the modified O&P method and the G&S energy method. The results show that the interface of (Ti, Nb)(C, B)/IN625 composite coatings is affected by about 670 kJ Joule heat released from the in-situ reaction, and the interfacial width reaches 24 μm, so that it is 6 times higher than that of IN625 coating prepared by EHLA, which effectively reduces the stress gradient in the interfacial region and alleviates the stress mismatch on both sides of the interface. However, the surface hardness of (Ti, Nb)(C, B)/IN625 composite coating is lower than that of the IN625 coating, with a value of about 240 HV0.2, and the average wear weight loss was only 10% of that of the IN625 coating, which is on the one hand attributed to the in-situ authigenic TiCB, TiC, NbMo3B4, and NbMo2B2 phases supporting the (Ti, Nb)(C, B)/IN625 composite coating substrate to achieve the abrasion reduction and wear resistance. On the other hand, it is attributed to the formation of nano-equiaxial ultrafine grains in the depth range of 250 nm below the wear surface area by the coupling of the three fields of plastic rheology-heat-force, which dynamically strengthens the wear surface.

We report a detailed investigation of vibrational modes, structure, and dynamics of glutathione (GSH) solutions using ultrasonic relaxation spectroscopy, FT-IR vibrational spectroscopy and electronic absorption measurements. The experimental data were analyzed in view of density functional theory (DFT) and molecular docking calculations. Three distinct Debye-type relaxation processes are resolved in the acoustic spectra, which are assigned to conformational changes between GSH conformers, self-association of GSH, and protonation processes. The standard volume changes for each process were estimated both experimentally and theoretically revealing a close resemblance among them. The higher the effect of the relaxation process in the structure, the greater the induced volume changes. From the temperature dependence of specific acoustic parameters, the thermodynamic characteristics of each process were determined. The experimental FT-IR spectra were compared with the corresponding theoretically predicted vibrational spectra revealing that the GSH dimers and extended conformers dominate the structure of GSH solutions in the high concentration region. The absorption spectra in the ultraviolet region confirmed the gradual aggregation mechanism that takes place in the aqueous GSH solutions. The results of the present study were discussed and analyzed in the framework of the current phenomenological status of the field.

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

The development of solid-state forms of drugs is an effective mean of solubility enhancement. In this study, two polymorphs named form C, form D, and two co-crystals of sorafenib (SF) with oxalic acid (SF-OA) and malonic acid (SF-MA), by evaporation and slurry method, have been developed and characterized. The single-crystal X-ray diffraction results showed that the structure of form C was similar to of form I. It had similar cellular parameters, but different arrangement of stacking due to π-π conjugation. The drug molecules in SF-OA underwent torsional folding through four hydrogen bonds of intermolecular and intramolecular. The solubility performance of solid-state forms improved significantly. Compared with form I, form C and form D were 1.59, 1.49 times at pH 1.2 HCl, 1.59, 1.87 fold at pH 6.8 PBS. In particular, the SF-OA and SF-MA increased the apparent solubility of SF at pH 1.2 by 8.3 and 6.4 times, at pH 6.8 by 4.0 and 4.5 times respectively. The dissolution mechanisms were analyzed. New solid-state forms showed strong stability at storage conditions of 40 °C/75% RH and 60 °C/0% RH. Notably, the crystal of SF preferred to transform in mixed solvents, and the formation of co-crystals confirmed the ∆pKa rule.

The well-known equations for the process of powder compaction (PCP) in a rigid die published over the period from the beginning of the last century to the present are considered. Most of the considered equations are converted into the dependence of the densification pressure on the relative density. The equations were analyzed and their ability to describe PCP was assessed by determining the coefficient of determination when approximating experimental data on the compaction of various powders. It is shown that most of the equations contain two constants, the values of which are determined by fitting the mathematical dependence to the experimental curve. Such equations are able to describe PCP with high accuracy in the case of compaction of powders up to a relative density of 0.9-0.95. It is also shown that different equations can describe PCP in the range of density change from the initial to 0.9 with the same and sufficiently high accuracy, but when the process of compaction is extrapolated to higher values of density, the curves diverge. This indicates the importance of equations that can unambiguously describe PCP to a relative density equal to or close to 1.0. For an adequate description of PCP to a relative density greater than 0.95, equations containing three or four constants have proven themselves well.

A hydrothermal technique with microwave heating (200 °C, 2 hours, 2 magnetrons, 2.45 GHz) was modified to obtain UV-C luminescent LaPO4: Pr3+ colloidal nanorods for the potential use in X-ray cancer theranostics. For further possible biofunctionalization, a compound of tartaric acid formed under basic conditions was used as a coating and stabilizing agent to provide colloidal properties to the surface of nanoparticles in basic to neutral aqueous media, which was confirmed by zeta potential measurements. In addition, the colloidal properties and clustering processes of synthesized LaPO4:Pr3+ nanorods in aqueous solutions with different pH values were studied in real time using a highly sensitive laser ultramicroscope operating according to the “light-sheet” scheme. A comparative analysis of the transmission electron microscopy, X-ray powder diffraction and high-energy spectroscopy showed the different effects of synthesis parameters on the morphological, crystalline and luminescent properties of the obtained nanorods. Through optimization of the synthesis parameters, stable aqueous solutions of m-LaPO4:Pr3+ nanorods with sizes less than 30 nm and an intensity of UV-C luminescence equal to 5-10% of the unmodified nanofibers were obtained.

Carvacrol is well-documented for its antibacterial and antioxidant effects. However, its high volatility has directed researchers towards nanoencapsulation technology according to bioeconomy and sustainability trends. This study examined and compared carvacrol microemulsion (MC), carvacrol microemulsion busted with chitosan (MMC) and carvacrol nanoemulsions as active coatings on extending minced pork meat shelf-life at 4±1 oC for 9 days, focusing on microbiological, physiochemical, and sensory characteristics. The research involved pre-characterizing droplet sizes, evaluating antioxidant, and determining antibacterial efficacy. The results demonstrated that NC with a 21 nm droplet size exhibited the highest antioxidant and antibacterial activity. All coatings succeed to extend the preservation of fresh minced pork meat in comparison to free carvacrol sample (FC). NC coating showed the highest extension of minced pork meat preservation and maintained meat freshness for 9 days, with a lower TBARs of 0.736 mg MDA/Kg, and effectively reduced mesophilic, lactic acid, and psychrotrophic bacterial counts more significantly 1.2, 2, and 1.3 log respectively as compared to FC. Sensory assessments confirmed the acceptability of NC and MCC coatings. Overall, the carvacrol based nanoemulsion can be considered as novel antioxidant and antimicrobial active coating due to its demonstrated higher efficacy in all the examined tests performed.

MoS2 lithium-based grease is suitable for lubrication protection between bearings at high temperatures and loads due to its excellent tribological properties. However, there is little research on the influence of different addition methods of MoS2 additive on the tribology and corrosion properties of lithium grease. In this work, vegetable oil with low toxicity, high biodegradation rate, and low cost was selected as the base oil, lithium 12-hydroxystearate as the thickener, and MoS2 as the additive. The effects of different adding modes of MoS2 on the tribology and corrosion properties of lithium grease were studied. The experimental results showed that adding 0.01wt% MoS2 before thickening was more conducive to improving the tribological properties of lithium grease. The average friction coefficient was 0.034, and the average spot diameter was reduced by 0.16mm. After grinding and adding 0.01wt% MoS2, the corrosion inhibition efficiency of the steel sheet was as high as 96.97%. The main reason was that the longer stirring and grinding were conducive to the uniform distribution of MoS2 in the grease, and the protective film formed by MoS2 and GCr15-bearing steel improved the lubrication performance and corrosion inhibition performance of the friction system.

Silybum marianum is a therapeutic plant belonging to the family Asteraceae. It contains silymarin, as its principal component, and has been reported to demonstrate hepatoprotective activity. The study was aimed to investigate the phytochemical constituents, synthesis of nanoparticles, antioxidant activity and antimicrobial effects of the leaf extract. Extracts were synthesized from AgNO3 and characterized via FT-IR, U.V and XRD. The antioxidant activity was determined using DPPH, H2O2 and β-carotene assays. Similarly, all extracts expressed significant DPPH inhibition (IC50) of 5.1, 5.0, 4.7, 2.3, 4.3 and 1.1 (ug/mL), H2O2 of 1.3, 2.2, 4.7, 5.6, 4.0 and 1.0 (ug/mL) from the methanol/water extract, nanoparticles, n-Hexane, ETOAC, n-Butanol and Ascorbic acid (standard) respectively. The extract exerted scavenging activity on β-carotene with a significant IC50 inhibition of 1.5, 0.8, 5.2, 0.8, 2.7, 4.8 at 0 hour and 1.5, 0.8, 5.2, 0.8, 2.7 and 4.8 (ug/mL) after 2 hours water bath incubation at 50°C in the order of the extracts above. Additionally, nanoparticles and plant extracts significantly (p<0.0001) inhibited the growth of bacteria with mean zone of inhibition ranging 7-13 mm and 4-11 mm. This study demonstrated that extracts from different solvents of S. marianum possess significant antioxidant activity, as well as antimicrobial effects which are all concentration dependent. Thus, the result suggests that methanolic/water leaf extract of S. marianum could serve as a potential source of antioxidants and can be explored as a therapeutic agent in free radical induced diseases.

Critical sized bone defects and articular cartilage injuries resulting from trauma, osteonecrosis or age-related degeneration are often nonhealing by the physiological repairing mechanisms, thus representing a clinic issue due to the relevant epidemiological incidence. Current treatment approaches consist of autologous or allogenic grafting, which are associated with painfulness, morbidity, risk of infections and rejection. Novel tissue-engineering approaches, aiming at the reconstruction of damaged tissues, have been proposed as alternative solutions to these conven-tional methods. These approaches are based on the combination of three fundamental compo-nents: autologous or allogenic cells, a scaffold and growth-stimulating signals, which are gener-ally referred to as the tissue engineering triad. Three-dimensional polymer networks are fre-quently used as scaffolds to allow cell proliferation and tissue regeneration. In this scenario, cryogels are giving promising results as cell scaffolds over other polymer networks, thanks to their peculiar properties. In particular, cryogels possess an interconnected porous structure and a typical sponge-like behaviour, which facilitate the cellular infiltration and ingrowth. Their properties can be appropriately adjusted to match the requirements of the specific tissue or or-gan that it is intended to regenerate. In this review it is reported the state of the art on the fabri-cation and employment of cryogels in supporting osteo or chondro-genic differentiation for the re-building of more organized tissues. Moreover, it will highlight current progress and future perspectives in the implementation of this technology in the clinical practice.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

Volatile organic compounds (VOCs) are molecules present in our everyday life, and they can be positive, such as in the formation of odour and food flavour, or harmful for environment and humans, and the research is focusing on limiting their emissions. Various methods have been used to achieve this purpose. Firstly, we review three main degradation methods: activated carbon, photocatalysis and a synergetic system. We provide a general overview of the operative conditions and report the possibility of VOC abatement during cooking. Within the literature, none of these systems has ever been tested in presence of complex matrices, such as during a cooking process. The aim of this study is to compare the three methods in order to understand the behaviour of filter systems in the case of realistically complex gas mixtures. Proton Transfer Reaction - mass spectrometry (PTR-MS) has been used as real-time monitoring of volatilome. Since VOC emissions are highly dependent on the composition of the food cooked, we evaluated the degradation capacity of the three systems for different burger types (meat, greens and fish). We demonstrate pros and cons of the photocatalysis and adsorption and how a combined approach can mitigate the drawbacks of photocatalysis.

The gel prepared by Nemipterus virgatus (N. virgatus) surimi alone still has some defects in texture and taste. Complexing with polysaccharides is an efficient strategy to enhance the gel properties. The main objective of the study was to analyze the relationship between the gel quality and molecular interaction of N. virgatus surimi gel after complexing with tapioca starch. The results make clear that the gel strength, hardness, and chewiness of surimi gel were increased by molecular interaction with tapioca starch. At the appropriate addition amount (12%, w/w), the surimi gel had excellent gel strength (17.48 N), water holding capacity (WHC) (89.01%), lower cooking loss rate (CLR) (0.95%), and shorted T2 relaxation time. Microstructure analysis indicated that the addition of tapioca starch made the surimi gel evenly distributed in the gel network structure, resulting in a significant reduction in cavities diameter, and the minimum diameter could be reduced to 20.33 μm. In addition, tapioca starch enhanced the hydrogen bond and hydrophobic interaction in the gel system and promoted the transformation of α-helix to β-sheet (P&lt;0.05). Correlation analysis showed that the increased physicochemical properties of surimi gel was closely related to the enhanced non-covalent interactions. In conclusion, the non-covalent complexation with tapioca starch is an efficient strategy to enhance the gel quality of surimi gel.

Speciation analysis is a relevant topic since the (eco)toxicity, bioavailability, bio (geo)chemical cycles, and mobility of a given element depend on its chemical forms (oxidation state, organic ligands, etc.). Reliability of analytical results for chemical species of elements depends mostly on the maintaining of their stability during sample pretreatment step and on the selectivity of further separation step. Solid phase extraction (SPE) is a matter of choice as most suitable and widely used procedure for both enrichment of chemical species of elements and their separation. Features of sorbent material are of great importance to ensure extraction efficiency from one side and selectivity from other side of SPE procedure. This review presents an update on the application of polymeric materials in solid-phase extraction used in non-chromatographic methods for speciation analysis.

In order to obtain the good match between yield strength and low-temperature toughness, the short-time partial austenitization (SPA) process was employed for V-microalloying 0.22C-5.24Mn steel. The initial microstructure after intercritical tempering was dual-phase ferrite and reversed austenite (RA), while the final microstructure was consisted of ferrite, RA and secondary martensite (SM) after subjected to SPA process. (V, Mo)C with disc-like morphology mainly precipitated during intercritial tempering, and the aspect ratio of particle decreased, leading to the appearance of near-spherical morphology. After subjected to SPA process, the resultant multiphase hierarchical microstructure (three layers: out layer of ferrite, interlayer of SM and inner layer RA) enabled high yield strength of 1097 MPa, total elongation of 14%, and impressive impact energy of 33.3 J at -20 °C. The strengthening contribution of (V, Mo)C precipitation was estimated about 108 MPa.

High-temperature cooking process like frying, baking, smoking, or drying can induce chemical transformations in conventional food ingredients, causing deteriorative modifications. These reactions, including hydrolytic, oxidative, and thermal changes, are a common occurrence and can result in alterations to the food's chemical composition. In this study, a combination of sucrose and histidine (Su-Hi) was transformed through a process of charring or pyrolysis. The GC-MS profiling study showed that when sucrose and histidine (Su-Hi) are exposed to high temperatures (≈240°C), they produce carbonyl and aromatic compounds including beta-D-Glucopyranose, 1,6-anhydro (10.11 %), 2-Butanone, 4,4-dimethoxy- (12.89 %), 2(1H)-Quinolinone-hydrazine (5.73%), Benzenamine (6.35%), 2,5-Pyrrolidinedione, 1-[(3,4-dimethylbenzoyl)oxy]- (5.82%), Benzene-(1-ethyl-1-propenyl) (5.62%), and 4-Pyridinamine-2,6-dimethyl (5.52%). The compounds mentioned have the ability to permeate the cell membrane and contribute to the development of cell death by necrosis in human immune cells. The evidence available suggests that a specific set of pyrolytic compounds may pose a risk to immune cells. This investigation reveals the complex relationship between high-temperature cooking-induced transformations, compound permeation inside the cells, and downstream cellular responses, emphasizing the significance of considering the broader health implications of food chemical contaminants.

The synthesis and characterization of the multicomponent crystals formed by 2,2’-thiodiacetic acid (H2tda) and 2,6-diaminopurine (Hdap) or N9-(2-hydroxyethyl)adenine (9heade) are reported. The crystals are in the salt rather than cocrystal form, as witnessed by single crystal X-ray diffractometry where a structural analysis revealed their ionic nature, confirming the proton transfer from the 2,2’-thiodiacetic acid to the basic groups of the coformers. The new multicomponent crystals have molecular formulas [(H9heade+)(Htda)] (1) and [(H2dap+)2(tda2)]·2H2O (2), and were also characterized by FTIR, elemental analysis as well as thermogravimetric/differential scanning calorimetry (TG/DSC) analyses. In the crystal packing the ions interact with each other via O–H···N, O–H···O. N–H···O and N–H···N hydrogen bonds generating cyclic hydrogen bonded motifs with graph-set notation of R22(16), R22(10), R32(10), R33(10), R22(9), R32(8) and R42(8), to form different supramolecular homo- and hetero-synthons. In addition, in the crystal packing of 2, pairs of diaminopurinium ions display an strong anti-parallel ,-stacking interaction, with short inter-centroids and interplanar distances (3.39 and 3.24 Å respectively) and fairly tight angle (17.5°). These assemblies have been further analyzed energetically by using DFT calculations, MEP surface analysis and QTAIM characterization.

The endo- and exo-N-heterocyclic carbene precursors based on camphor were prepared diastereoselectively in five synthetic steps starting from (1S)-(+)-ketopinic acid. The obtained N-heterocyclic carbene precursors were investigated in an asymmetric benzoin reaction. All new compounds were fully characterized and the absolute configurations were determined by X-ray diffraction and NOESY measurements.

The Semiconductor and Liquid Assisted Photothermal Effect (SLAPE)” concept was employed for the first time in this study to generate electricity from sunlight. In SLAPE process, a semiconducting material is immersed completely in a stable organic solvent to capture the complete sunlight reaching the earth surface and to turn it into the heat-energy that can be eventually converted into electricity by using Organic Rankine Cycle (ORC) with the help of a heat engine and electric generator. In this investigation, the SLAPE solar panels were fabricated with two top and bottom chambers separated by thin thermally conducting metal sheet (Cu or Al). Multi-crystalline silicon photovoltaic cells (SPVCs) in conjunction with -butyrolactone were employed to capture the sunlight, and a low-boiling point dichloromethane (DCM) solvent was employed as a working fluid to capture the in situ generated heat energy from sunlight. Upon exposure to the natural sunlight, the 21 numbers of SPVCs together with about 2 litres -butyrolactone containing one square meter area SLAPE solar panel has generated about 17 V when integrated with a laboratory model reciprocally moved steam engine and a custom-made electric generator, whereas, a commercial SPVC solar panel with 21 number SPVCs generate a maximum voltage of 11 V. The theoretical background governing the SLAPE solar panels, the necessity for their invention and the proof of concept of SLAPE solar panels have been thoroughly presented and discussed and established in this article.

Black-purple carrots possess, apart from carotenoids, high content of other bioactive pigments such as anthocyanins. However, both carotenoids and anthocyanins are modified over cold storage due to their lability. In this work, we investigated the effect of the postharvest elicitation on nutritional and organoleptic quality of purple carrots over storage at 5°C for 21 days. Based on our experience, we considered methyl jasmonate and abscisic acid as elicitors. The values obtained were compared with those provided by the fresh-untreated sample on the treatment day (ie, day 0) and after three-week storage (ie, on day 21), which were used as a reference. As a result, carotenoid content increased naturally in untreated samples over storage whereas anthocyanins maintained invariable. Also, physicochemical parameters reflected apparent organoleptic quality loss. However, the postharvest treatment of purple carrot samples with elicitors resulted in similar carotenoid content in elicited samples to fresh carrots on day 0 as well as lower concentration of anthocyanins and antioxidant activity. Besides, elicitation, particularly with abscisic acid, enabled purple carrot deterioration to be slowed down and, therefore, the organoleptic quality to be preserved. This suggests delaying effect of both elicitors on the spoilage rate of purple carrots over the storage time. These findings indicate that the postharvest application of elicitors may be an interesting conservation method, alternative to traditional procedures, to decelerate decomposition and extend shelf-life of purple carrots.

Nanocomposites of cyanate ester resin (CER) filled with three different reactive amino-functionalized polyhedral oligomeric silsesquioxane (POSS) were synthesized and characterized. The addition of a small quantity (0.1 wt.%) of amino-POSS chemically grafted to the CER network led to increasing thermal stability of CER matrix. A significant increase of the glass transition temperature, Tg (DSC data), and the temperature of α relaxation, Tα (DMTA data), by 45-55 оС of CER matrix with loading of nanofillers was evidenced. CER/POSS films exhibited a higher storage modulus than that of neat CER in the temperature range investigated. It was evidenced that CER/aminopropylisobutyl (APIB)-POSS, CER/N-phenylaminopropyl (NPAP)-POSS, and CER/aminoethyl aminopropylisobutyl (AEAPIB)-POSS nanocomposites induced a more homogenous α relaxation phenomenon with higher Tα values and an enhanced nanocomposite elastic behavior. Furthermore, CER/amino-POSS nanocomposites possessed higher specific surface area, gas permeability (CO2, He), and diffusion coefficients (CO2) values than those for neat CER, due to increasing free volume of the nanocomposites studied that is very important for their gas transport properties. Permeability grew respectively by about 2 (He) and 3.5-4 times (СО2), and diffusion coefficient of CO2 increased approximately twice for CER/amino-POSS nanocomposites in comparison with the neat CER network. The efficiency of amino-functionalized POSS in improving the thermal and transport properties of the CER/amino-POSS nanocomposites increased in a raw of reactive POSS containing one primary (APIB-POSS) &lt; eight secondary (NPAP-POSS) &lt; one secondary and one primary (AEAPIB-POSS) amino groups. APIB-POSS had the least strongly pronounced effect, since it could form covalent bonds with the CER network only by reaction of one –NH2 group, while AEAPIB-POSS displayed the most highly marked effect, since it could easily be incorporated into the CER network via reaction of –NH2 and –NH– groups with –O–C≡N groups from CER.

Treatment of the non-purified mixture of dinitro isomers obtained from the nitration of 1,4-dimethoxybenzene with piperidine, led to the isolation of novel but minor adduct, 1-(2,5-dimethoxy-4-nitrophenyl)piperidine (2b) in 15% yield. Yields of nucleophilic aromatic substitution adducts are high when using purified 1,4-dimethoxy-2,5-dinitrobenzene (1b) with piperidine and pyrrolidine to give 2b and 1-(2,5-dimethoxy-4-nitrophenyl)pyrrolidine (3b) in 76% and 82%, respectively.

Nanofibers are one of the most attractive materials that can modify functionalities for developing new kinds of specific applications, mainly used as a biomedical material. Herein, we designed and prepared the antibacterial nonwoven fiber mats of PLA and PLA composited with Ag nanoparticles by electrospinning. The effects of varying filler contents on their chemical, surface morphology, thermal, water absorbency, and antibacterial properties were investigated using FTIR, SEM/EDS, DSC, swelling ratio, and qualitative and quantitative antibacterial tests. FTIR and EDS spectra indicated that Ag nanoparticles were incorporated in the PLA without chemical bonding. SEM revealed that the average diameter of the PLA nanofibers containing the Ag nanoparticles was more significant than those without those particles. Besides, fiber diameters are proportionally the amount of Ag nanoparticle contents. DSC indicated that the Ag nanoparticles can be incorporated within the PLA-matrix without strongly affecting their thermal properties. Moreover, the crystallinity of the composite nonwoven fiber mats was higher than those of fiber mats in the neat PLA. Accordingly, the antibacterial activities revealed that all the composite nanofiber mats exhibited excellent against S. aureus and E. coli bacterial strains. In addition, in the cell toxicity study, all produced hybrids nonwoven fiber mats induced a reduction in cell viability for the L929 fibroblast cells. Our results suggest that the designed and prepared nonwoven fiber mats may have good potential for use in the biomedical field, particularly in wound dressing applications

In this work we developed two new polyfunctional hybrid systems, in which the presence of Fc redox "antennas" on peptide scaffolds allows a modulation of their electronic properties. Specifically, we synthesized two helical hexapeptides containing four Aib (α-amionoisobutyric acid) and two L-Dap (2,3-diamino propionic acid) residues. L-Dap side chains were then functionalized with Fc moieties. The structures of the two 310 helical peptides, namely Z-Aib-L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr and Z-Aib-L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr, were investigated by X-ray diffraction, 2D-NMR, CD and IR spectroscopies. Due to the helical conformation, in Z-Aib-L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr the Fc groups are located on the same face of the helix, in Z-Aib-L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr on opposite faces. Surprisingly, two bands were found in DPV for Z-Aib- L-Dap(Fc)-Aib- L-Dap(Fc)-Aib-Aib-NH-iPr, indicating electrostatic interaction between the Fc groups despite their longer reciprocal distance with respect to that in Z-Aib- L-Dap(Fc)-Aib-Aib- L-Dap(Fc)-Aib-NH-iPr. CD experiments at different concentrations evidenced aggregation for Z-Aib- L-Dap(Fc)-Aib-L-Dap(Fc)-Aib-Aib-NH-iPr even at high dilution, thus suggesting that the Fc-Fc electrostatic interaction could be of intermolecular nature.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

Novel antibacterial silver nanomaterials have become promising substitutes for traditional antibiotics, because pathogens do not develop resistance to them. However, it is necessary to produce silver nanoparticles with appropriate size and better performance through a green and simple synthesis process. In the present study, Fructus mori-composite silver nanoparticles (M-AgNPs) were greenly synthesized using medicinal plant mulberry fruits (Fructus mori), with silver nitrate (AgNO3) as a precursor. UV-Vis spectroscopy and X-ray diffraction (XRD) indicated the formation of silver nanoparticles with face centered cubic structure. Fourier transform infrared (FTIR) spectroscopy confirmed the reducing and capping effects of mulberry fruits' active components (polyphenols, flavonoids, etc.) on M-AgNPs. The reaction parameters including temperature, time, pH, and concentration of AgNO3 were gradually optimized. The particle size and morphology of M-AgNPs were measured by dynamic light scattering (DLS) and transmission electron microscopy (TEM) techniques. The minimum particle size of M-AgNPs was about 30 nm, and they were approximately spherical and equably distributed. The excellent stability of M-AgNPs ensured that no agglomeration occurred for up to 60 days. The antioxidant activity of M-AgNPs was evaluated by 1,1-diphenyl-2-trinitrophenylhydrazine (DPPH) assay, and the DPPH radical clearance rate of M-AgNPs was up to about 79%. Greenly synthesized M-AgNPs exhibited better antibacterial activity than chemically synthesized commercial silver nanoparticles (C-AgNPs), due to the active molecules attached to their surfaces. The inhibition zone diameters of M-AgNPs against P.aeruginosa, E.coli and S.aureus were 13.9±0.4、12.2±0.3、12.8±0.7 mm, respectively. Such greenly synthesized AgNPs from medicinal plants have good prospects in the field of biomedicine.

Water electrolysis is a highly efficient route to produce ideally clean H2 fuel with excellent energy conversion efficiency and high gravimetric energy density, without producing carbon trace unlike steam methane reforming, and resolves the issues of environmental contamination via replacing the conventional fossil fuel. Of special importance lies in the advancement of highly effective non-precious catalysts for the oxygen evolution reaction (OER). The electrocatalytic activity of an active catalyst mainly depends on the material conductivity, accessible catalytically active sites, and intrinsic OER reaction kinetics, which can be tuned via introducing heteroatom N in the catalyst stricture. Herein, an efficacious nitrogenation of CuS has been accomplished, which was synthesized using hydrothermal procedure, and characterized for their electrocatalytic activity towards OER. The nitrogen-doped CuO@CuS (N,CuO@CuS) electrocatalyst exhibits superior OER activity than pristine CuS (268 and 602 mV), achieving the low overpotential of 240 and 392 mV at a current density of 10 and 100 mA/cm2, respectively, ascribed to the favorable electronic structural modification triggered by nitrogen incorporation. The N,CuO@CuS also exhibits excellent endurance under varied current rates and a static potential response over 25 h stability measured at 10 and 100 mA/cm2.

Vanadium(IV) chalcogenide materials are of increasing interest for use in catalysis and energy conversion-related applications. Since no ternary compounds are yet known in the V–Se–Te system, we studied ternary VwSeyTe2–y (w = 1.10, 1.13; y = 0.42, 0.72) phases crystallizing in space group P3m1 (no. 164). Two single-crystal specimens with differing compositions of a solid solution were obtained using the ceramic method. All products were characterized by either single-crystal or powder X-ray diffraction. The lattice parameters increase with rising tellurium content in accordance to the larger ionic radius of the tellurium anion compared to selenium. The chemical compositions were confirmed by energy dispersive X-ray spectroscopy. Further, magnetic measurements revealed mostly antiferromagnetic properties. Simultaneous differential scanning calorimetry/thermogravimetric analyses in nitrogen atmosphere showed endothermic decomposition accompanied by the formation of VN. The results of this work can serve as a basis for the synthesis of new phases in the V–Se–Te and related vanadium chalcogenide systems.

Cellulose-based carbon (CBC) has been widely concerned with its porous structure, high specific surface area, and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, ZnO/CBC heterojunction was formed by means of simple co-precipitation and high temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia compared with that of the previous pure ZnO ammonia sensor can not at room temperature. It has great gas sensing response, stability and selectivity to ammonia concentration at 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

A 17th century wall painting representing a Virgin between two Saints in a noble Italian renaissance palace, Palazzo Gallo in Bagnaia (Viterbo, Italy), was restored in 2021 in the context of a wider restoration campaign interesting the main room of the palace built by cardinal Sansoni Riario. Diagnostic analyses done with traditional characterization techniques (optical microscopy on micro-stratigraphic sections, X-ray fluorescence spectroscopy and Fourier transform infrared spectroscopy) provided the identification of both original painting and restoration materials, while imaging investigations as ultraviolet fluorescence photography, false color images and multispectral mapping provided by hypercolorimetric multispectral imaging (HMI) technique enabled the evaluation of the state of conservation, locating restoration interventions and supporting the monitoring of the cleaning procedure. An altered protective Paraloid-based coating dating from early 2000s had to be removed due to the unpleasant glossy finishing given to the painted surface, making the scene barely readable. To pursue a restoration protocol based on environmental sustainability and green chemistry, enzyme-based gels marketed by Nasier-Brenta© and CTS© companies were tested in different protocols for the cleaning of the mash covering the painting. Although some interesting results were observed, the enzymatic cleaning had a scarce effectiveness with timing beyond a reasonable interval. Traditional chemical solvents as Dowanol PM (methoxy-propanol) and benzyl alcohol were necessary to complete the cleaning of the painting surface.

In this study, the effects of combined addition of CeLa and GdY on microstructure and mechanical properties of as-cast Al-4Cu-1Mn alloys were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopies (TEM) and tensile testing. The results show that the minor addition of CeLa and GdY leads to the refinement of grain size. The addition of CeLa results in the formation of supersaturated vacancies in the Al matrix, whereas the addition of GdY leads to a decrease in the precipitation temperature of the Al2Cu phase. The combined CeLa and GdY addition can significantly increase ultimate tensile strength (UTS) while losing only a small amount of elongation (EL). Compared with the unmodified alloy, the grain size and SDAS of the alloy (0.2 wt% CeLa + 0.1 wt% GdY) were diminished by 67.2% and 58.7%, respectively, while maximum hardness and UTS rose by 31.2% and 36.9%, correspondingly.

The adsorption of actinide ions (Am(III) and U(VI)) from aqueous solutions by pristine and oxidized carbon fabrics has been investigated by means of batch experiments at different pH values (4, 7 and 9) and temperatures (25, 35 and 45 °C) under ambient atmospheric conditions. The experimental results indicate that both pH and fabric texture affect the adsorption rate and the relative removal efficiency, which results at 70% and 100% for Am(III) and U(VI), respectively. The Kd (L/kg) values for U(VI) have been generally found to be higher (2 &lt; log10(Kd)&lt; 3) than the corresponding values for the Am(III) adsorption (1.5 &lt; log10(Kd) &lt; 2). The data obtained from the experiments regarding the temperature effect imply that the relative adsorption for both actinides increases with temperature and that the adsorption is an endothermic and entropy-driven reaction. Application of the fabrics to remove the two actinides from contaminated seawater samples shows that both the relative removal efficiency and the Kd values decrease significantly due to the presence of competitive cations (e.g., Ca2+ and Fe3+) and complexing anions (CO32-) in the respective waters. Nevertheless, the removal efficiency is still remarkable (50% and 90% for Am(III) and U(VI), respectively), demonstrating that these materials could be attractive candidates for the treatment of radionuclide/actinide contaminated waters.

The surprisingly high catalytic activity of gold has been known to the heterogeneous catalysis community since the mid-1980s. Significant effort has been directed towards improving the reactivity of these surfaces towards important industrial reactions. One such strategy is the introduction of small amounts of other metals to create Au-based surface alloys. In this work, we investigate the synergistic effect of Pt doping of the Au(111) surface towards decreasing the activation barrier of the methanol dehydrogenation elementary step, within first-principles density functional theory. To this aim we construct several models of \ce{Pt}-doped Au(111) surfaces, including a full \ce{Pt} overlayer and monolayer. The effect of \ce{Pt} surface doping is then investigated via the computation of adsorption energies of the various chemical species involved in the catalytic step, and the estimation of activation barriers of methanol dehydrogenation. Both electronic and strain effects induced by \ce{Pt} surface doping concur in substantially lowering the activation energy barrier of this important reaction elementary step. Morever, in the presence of preadsorbed atomic oxygen, \ce{Pt} surface doping can be used to reduce the activation energy for methanol dehydrogenation to as low as 0.1 eV.

Electrochemical Impedance Spectroscopy techniques were applied in this work to 9 lead-acid battery prototypes fabricated industrially, divided on three type/technology packages. Frequency dependent impedance changes were interpreted during successive charge/discharge cycles on two distinct stages: 1) immediately after fabrication; and 2) after a controlled aging procedure to 50% Depth of Discharge, following industrial standards. By investigating their State of Health behaviour vs electrical response, three methods were employed, namely the (Q-Q0) total charge analysis, the decay values of Constant Phase Element in the equivalent Randles circuits, and the resonance frequency of the circuit. A direct correlation has been found for prediction of the best performant batteries in each package, thus allowing a qualitative analysis capable to provide the decay of the battery State of Health. We emphasized which parameters are directly connected with their lifetime performance in both stages, and by consequence, which type/technology battery prototype emphasize the best performance. Based on this methodology, the industrial producers can further establish the quality of the novel batteries in terms of performance vs lifespan, allowing them to validate the novel technological innovations implemented in the current prototypes.

Adding zinc (II) and formate anions improves the thermal phase-stability of alpha-FAPbI3 materials and the spin-coated thin films of such doped FAPbI¬3 show an increased emission lifetime of up to 3.7 microsecond on quartz. This work investigates the effects of zinc and formate on the stability and time resolved photoluminescence of FAPbI3 perovskites for solar cell applications. Perovskite samples with varying concentrations of zinc and formate were made by incorporating different amounts of zinc formate and zinc iodide and characterized with XRD. Doping levels of 1.7% Zn(II) and 1.0% formate (relative to Pb) seem optimal. The thermal stability of the perovskite powders and thin films were assessed. XRD was virtually unchanged after 6 months. The time-resolved photo-luminescence spectroscopy of the doped spin-coated perovskite samples is reported. The results show that synergy between an anionic and a cationic dopant can take place, making the perovskite thermally more stable with a longer charge carrier lifetime.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Some bispecific radiotracers have been developed to overcome the limitations of monospecific tracers and improve detection sensitivity for heterogeneous tumor lesions. Here we aim to synthesize two bispecific tracers targeting prostate-specific membrane antigen (PSMA) and fibroblast activation protein (FAP), which are key markers expressed in prostate cancer. A pyridine-based FAP-targeted ligand was synthesized through multi-step organic synthesis, and then connected to the 2-Nal-containing PSMA-targeted motif. Ki(PSMA) values of Ga-complexed bispecific ligands, Ga-AV01084 and Ga-AV01088, were 11.6 ± 3.25 and 28.7 ± 6.05 nM, respectively, and the IC50(FAP) values of Ga-AV01084 and Ga-AV01088 were 10.9 ± 0.67 and 16.7 ± 1.53 nM, respectively. The uptake values for PSMA-expressing LNCaP tumor xenografts were 9.05 ± 1.54 and 8.85 ± 1.25 %ID/g for [68Ga]Ga-AV010184 and [68Ga]Ga-AV01088, respectively, which were lower than the monospecific PSMA-targeted tracer [68Ga]Ga-PSMA-617 (16.7 ± 2.30 %ID/g). The uptake values for FAP-expressing HEK293T:hFAP tumor xenografts were 1.90 ± 0.41 and 1.20 ± 0.25 %ID/g for [68Ga]Ga-AV01084 and [68Ga]Ga-AV01088, respectively, which were also lower than the monospecific FAP-targeted tracer, [68Ga]Ga-AV02070 (7.93 ± 1.88 %ID/g). Further investigations are needed to optimize the selection of linkers and targeted pharmacophores to improve the tumor uptake of PSMA/FAP bispecific tracers for prostate cancer imaging.

Drug nanosuspensions offer a promising approach to improve bioavailability for poorly soluble drug candidates. Such formulations often necessitate the inclusion of an excipient to stabilize the drug nanoparticles. However, a rationale to choose the correct excipient for a given drug candidate remains unclear. To gain molecular insight into formulation design, this work first utilizes molecular dynamics simulation to computationally investigate drug-excipient interactions for a number of combinations that have been previously studied experimentally. We find that hydrophobic interactions drive excipient adsorption to drug nanoparticles, and that the fraction of polar surface area serves as a predictor for experimental measurements of nanosuspension stability. To test these ideas prospectively, we applied our model to an uncharacterized drug compound, GDC-0810. Our simulations predicted that salt forms of GDC-0810 would lead to more stable nanosuspensions than the neutral form; therefore, we tested the stability of salt GDC-0810 nanosuspensions and found that the salt form readily formed nanosuspensions even without excipient. To avoid computationally expensive simulations in the future, we extended our model by showing that simple, two-dimensional properties of the single drug molecule can be used to rationalize nanosuspension design without simulation. In all, our work demonstrates how computational tools can provide molecular insight into drug-excipient interactions, and aid in rational formulation design.

In this study, the effect of increasing exposure time on microstructures, defectiveness, mechanical properties and corrosion behavior of selective laser melted sample Al-Si10-Mg powder have been investigated. The sample were processed at the same power (375 W) and scan speed (2000 mm/s) but with increasing exposure time. Exposure time equal to 40, 50 and 60 µs was applied. The features of the analyzed samples show that with increasing exposure time a better efficiency of the heat input has been obtained with larger size of melting pool and Si particles and lower defectiveness. Moreover, being the coarser microstructure associated a to lower level of voids, the average hardness is similar for the analyzed samples. The potentiodynamic curves of the samples show that the voids occurrence is more significant with respect to the scale of micro-structure on corrosion behavior being the sample processed at the highest exposure time the more resistant to corrosion. The experimental techniques used in the present study were Optical microscope, Sem microscope, Hardness and X-Ray Computed Tomography.

Using nanoparticles (NPs) in drug delivery has exhibited promising therapeutic potential 13 in various cancer types. Nevertheless, several challenges must be addressed, including the 14 formation of the protein corona, reduced targeting efficiency and specificity, potential immune 15 responses, and issues related to NP penetration and distribution within 3-dimensional tissues. 16 To tackle these challenges, we have successfully integrated iron oxide nanoparticles into 17 neuroblastoma-derived extracellular vesicles (EVs) using the parental labeling method. We first de- 18 veloped a tissue-engineered (TE) neuroblastoma model, confirming the viability and proliferation 19 of neuroblastoma cells for at least 12 days, supporting its utility for EV isolation. Importantly, EVs 20 from long-term cultures exhibited no differences compared to short-term cultures. Concurrently, 21 we designed Rhodamine (Rh), Polyacrylic acid (PAA)-functionalized magnetite nanoparticles 22 (Fe3O4@PAA-Rh) with high crystallinity, purity, and superparamagnetic properties (average size: 23 9.2 ± 2.5 nm). We then investigated the internalization of Fe3O4@PAA-Rh nanoparticles within 24 neuroblastoma cells within the TE model. Maximum accumulation was observed overnight while 25 ensuring robust cell viability. However, nanoparticle internalization was low. Taking advantage of 26 the enhanced glucose metabolism exhibited by cancer cells, glucose (Glc)-functionalized nanoparti- 27 cles (Fe3O4@PAA-Rh-Glc) were synthesized, showing superior cell uptake within the 3D model 28 without inducing toxicity. These glucose-modified nanoparticles were selected for parental labeling 29 of the TE models, showing effective NPs encapsulation into EVs. 30 Our research introduces innovative approaches to advance NPs delivery. By partially addressing 31 the challenges associated with 3D systems, optimizing internalization, and enhancing NPs stability 32 and specificity through EV-based carriers. Also, our findings hold the promise of more precise and 33 effective cancer therapies while minimizing potential side effects.

Given its exceptional attributes, aerogel is viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porousness, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textile sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogel formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multi-functionality of cellulose-based aerogels in the textile industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

A bridged 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) derivative (PN-DOPO) in combination with aluminum phosphates coated sepiolite (Sep@AlPO4) was used to improve the flame retardancy, thermal stability and mechanical properties of poly (ethylene oxide) (PEO)/poly (butylene adipate-co-terephthalate) (PBAT) blends. The synergistic effects of PN-DOPO and Sep@AlPO4 on the fire resistance, thermal decomposition behavior and mechanical properties of PEO/PBAT composites were investigated systematically. The results indicated that 5 wt % Sep@AlPO4 combined with 10 wt% PN-DOPO into PEO/PBAT achieved a V-1 rating in UL-94 test and the LOI value increased to 23.7%, meanwhile, the peak-heat release rate (p-HRR), av-HRR and total heat release (THR) values of PEO/PBAT/PN10%/Sep5% composites decreased by 35.6%, 11.0% and 23.0% compared with those of PEO/PBAT, respectively. The thermogravimetric analysis (TGA) results confirmed that PN-DOPO/Sep@AlPO4 could enhance the initial thermal stability and char yield of PEO/PBAT matrix, and TGA/Fourier transform infrared spectrometry (TGA-FTIR) results revealed that the composites exhibited the absorption peaks of phosphorous-containing groups and an increase in gas-phase volatiles during the thermal decomposition process. The digital photographs and morphological structures of char residues demonstrated that PN-DOPO and Sep@AlPO4 mixtures benefited to the formation of a more continuous and dense carbon layer on the composites surface during combustion. Rheological behavior revealed that a higher storage modulus, loss modulus and complex viscosity of PEO/PBAT/PN-DOPO/Sep@AlPO4 composites could also promote the cross-linking structure during burning. Furthermore, the PEO/PBAT/PN-DOPO/Sep@AlPO4 composites exhibited excellent mechanical properties in terms of elongation at break and flexural performance than the PEO/PBAT system. All the results demonstrated that PEO/PBAT system modified by the combination of PN-DOPO and Sep@AlPO4 not only exhibited excellent synergistic effect on the flame retardance, but also had good improvement on thermal stability and mechanical properties, indicating the potential application in areas requiring fire safety.

This article presents a comprehensive overview of the utilisation of nanotechnology in the cosmetics industry, with a specific focus on developing nanoparticles for the efficient delivery of active ingredients through skin penetration. The review delves into incorporating natural ingredients in cosmetics, exploring their therapeutic properties and the advantages and limitations associated with their use. Furthermore, the article examines the benefits of integrating natural ingredients into skincare products to enhance skin conditions, highlighting the application of nonfibrous technology in areas such as UV protection, anti-ageing effects, moisturisation improvement, and wound healing. Ultimately, the article emphasises the immense potential of nanotechnology to create innovative opportunities and positive societal impacts across various industries.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of high-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes are investigated. The main gas-phase and solid products of plasma-chemical transformations are determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems for optimal process parameters was carried out. Using the example of hydrogen reduction of SiCl4 by the method of numerical modeling, gas-dynamic and thermal processes for this type of discharge are investigated. The impurity composition of gas-phase and solid reaction products is investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, is shown.

The nanocomposites with reversible cross-linking covalent bonds were prepared by reacting furfurylamine (FA)-modified diglycidyl ether of bisphenol A (DGEBA) and furfuryl-functionalized aniline trimer-modified graphene (TFAT-G) with bismaleimide (BMI) via Diels-Alder (DA) reaction. The successful synthesis of the TFAT modifier is confirmed by NMR hydrogen spectroscopy and IR spectroscopy tests. The structure and properties of TFAT-G epoxy nanocomposites are characterized by SEM, DSC, tensile and resistivity CES. The results show that TFAT-G was uniformly dispersed in the resin, and 1wt% TFAT-G composites increase to 233% for tensile strength, 63% for elongation at break, 66.1% for modulus and 7.8℃ for Tg. Overall, the graphene/self-healing resin nanocomposites have both good self-healing function and electrical conductivity by adding 1% modified graphene and still maintain the original 83% strength and 89% electrical conductivity after one cycle of heating repair.

An effective approach to fabricate large-scale of conducting polyaniline (PANI) by an in situ anodic electrochemical polymerization on the nickel foam, which coated by a novel aryl diazonium salt (ADS)-functionalized graphene (ADS-G). In present work, ADS-G was used as a high surface area support material for electrochemical polymerization of PANI. Electrochemical performances of the ADS-G/PANI composites exhibited better suitability as supercapacitor electrode materials than that of the PANI. The ADS-G/PANI composites achieved the specific capacitance of 528 F g-1, which was higher than that of PANI (266 F g-1) due to the excellent electrode-electrolyte interaction and synergistic effect of electrical conductivity between ADS-G and PANI in the composites. These findings suggested that the ADS-G/PANI composites were a suitable composite for the potential supercapacitor applications.

Alkali-activated materials, sometimes called geopolymers, can be used as alternative cementitious materials to conventional Portland cement. There is a significant current interest in these materials due to their low CO2 footprint. Typical applications of alkali-activated materials are within civil engineering, however, potential applications as well cementing material within oil & gas are also being studied with emerging interest. This paper presents a systematic study of compressive strength development from 1 to 28 days for metakaolin-based alkali-activated cement. The results show that compressive strength is highly dependent upon the initial Si/Al ratio in the mix design, as well as the concentration of the activator solution. Furthermore, due to the relatively low initial reactivity of the used metakaolin material, different types of co-binders were included in the slurry composition to improve early strength development. The two different co-binders tested were another, more reactive metakaolin material and Blast Furnace Slag (GGBFS). It was found that both these co-binders performed as intended, by ensuring early strength development via precipitation of K-A-S-H and C-A-S-H gels, respectively, and also by enabling subsequent strength development due to improved dissolution of the low-reactive metakaolin.

Organic light-emitting diodes (OLEDs) have ushered in a technological revolution with their remarkable impact on diverse sectors of our daily lives. These versatile devices known for their outstanding display and lighting capabilities, have become indispensable components in various industries including smartphones, tablets, televisions, and automotive applications. This paper delves into the development of a group of twisted donor-acceptor-donor (D-A-D) derivatives incorporating bicarbazole and benzophenone structures for potential use as blue emitters in OLEDs. The synthesized compounds, namely DB14, DB23 and DB29, were designed with various alkyl side chains to enhance their film forming properties as for blue emitters. Characterization and evaluation of these derivatives included photophysical, electrochemical, thermal, and electroluminescent analysis. Some of the OLED devices incorporating these emitters demonstrated promising performance with maximum current efficiency (CEmax) of 2.6 cd/A and external quantum efficiency (EQEmax) of 5.3%. Notably, the DB23 emitter exhibited the highest EQE among all devices. The study also emphasizes the influence of host-guest energy transfer, optimal doping concentrations, and molecular structures on device performance. This research not only contributes to the understanding of advanced OLED materials but also provides insights into designing efficient blue emitters for future display and lighting applications, thereby advancing the field of organic electronics.

Ultra high molecular weight polyethylene (UHMWPE) is a thermoplastic high-performance polymer in high demand for biomedicine, ship and machine building, anthropomorphic robots and smart prostheses. Highly oriented UHMWPE fibers possess record specific strength and may also be used for the fabrication of self-reinforced PE-PE composites (SRPEC). The temperature evolution study of the small-angle X-ray scattering (SAXS) signature of the supramolecular structure of UHMWPE can help reveal their important role in the mechanism of the shape memory effect in SRPEC. The laboratory SAXS–WAXS beamline XEUSS 3.0 was used for in situ studies of the nanostructure parameters in unidirectional SRPEC. Namely, the radius of gyration and the dimensionality factor were extracted from 2D SAXS patterns using several fitting algorithms. Significant changes of these parameters occurred in temperature ranges that correspond to the initiation of the shape memory effect and melting. The relationship between the material anisotropy and 2D SAXS patterns are discussed in the context of the supramolecular structure evolution.

Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) is developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) are comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibits a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at -20 ℃. In contrast, the HR-QT steel exhibits tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consists of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reaches 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared to the HR-QT process, the TMCP-DQP process results in finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieves the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilizes the RA through carbon enrichment, while the relaxation stage reduces a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminates internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

Natural deep eutectic solvents (NADES) have been shown as selective and environmentally friendly solvents for the extraction of bioactive compounds. However, studies on the solubility of low molecular weight carbohydrates (LMWC) in NADES are scarce. In this work, new solubility data of LMWC in NADES are provided and a new approach based on the use of these solvents for the efficient fractionation of bioactive carbohydrates was explored for the first time. Several mono- and disaccharides and three NADES based on choline chloride (ChCl) and different donors [2-ethylene glycol (EtG), glycerol (Gly) and ethanedioic acid dihydrate (Eth)] were considered. While degradation of carbohydrates, mainly ketoses, was detected with ChCl:Eth due to its acidic nature, ChCl:EtG and ChCl:Gly were found to be useful alternatives for selectively separating bioactive ketoses and their corresponding aldoses (e.g. lactulose/lactose and tagatose/galactose) present in equimolar binary mixtures. In addition, the usefulness of ChCl:EtG for the selective enrichment of lactulose to be used as food ingredient or nutraceutical was proven (from a 25% in the reaction mixture to a 56% in the purified sample). NADES could be used for the selective fractionation of value-added carbohydrates from interfering sugars for several applications including food science, engineering or pharmaceuticals.

Naphtho[1,8-de][1,2]oxazin-4-ol and its acyl or benzyl derivatives ring open to various 2,8-dihydroxy-1-naphthonitriles, that undergo methylation, reduction, demethylation and debenzylation reactions, to afford the target compound (E)-2-hydroxy-8-methoxy-1-naphthaldehyde. The best overall yield of the latter was 28.7%. This compound was converted to its corresponding (E)-2-hydroxy-8-methoxy-1-naphthaldehyde ox-ime, which was oxidatively o-cyclized with phenyliodine(III) diacetate (PIDA) to 9-methoxynaphtho[1,2-d]isoxazole 2-oxide. The latter in deuterated DMSO, at room temperature, rearranged to its isomer to 2-hydroxy-8-methoxy(naphthalen-1-yl)nitrile oxide. The isomeriza-tion was detected by a time-course plot 1H NMR spectroscopy and further identified from its13C NMR and HRMS spectra. The nitrile oxide was stable in (non)deuterated DMSO for at least 18 hours. A 3,4-bis(2-hydroxy-8-methoxynaphthalen-1-yl)-1,2,5-oxadiazole 2-oxide as a dimeriza-tion product or an isocyanate as a rearrangement isomer were both ruled out, the former by the absence of the relevant molecular ion in its HRMS spectrum while the latter by 1,3-dipolar cy-cloaddition reactions with various dipolarophiles that gave substituted isoxazoles, thus con-firming the nitrile oxide structure.

Considering nutritional qualities of gofio (Gf) and aloe vera juice (AVJ), their combination is indicated as an easy and fast source of ingest of basic bio elements. As the texture of the final product must be accepted by customers, the influence of Gf concentration on the rheological behavior of Gf/AVJ suspensions was determined. Shear thinning index of AVJ maintains unaltered despite the presence of Gf particles, although the viscosity value increases as expected. Linear viscoelastic studies on Gf/AVJ confirmed this is a viscoelastic liquid that changes from chewy to creamy texture with Gf concentration increase.

(1) Background: The definition of value addition is based on the process or processes which are used to transform physically the initial raw material in the final food or non-food article. Diversification can enhance the possibility of increased gains. The aim of this work is to give a reliable description of value addition when speaking of coconut-based beverages among all possible derivatives; (2) Methods: a systematic review of main papers on the argument has been critically examined and discussed; (3) Results: Processing degree is a consequence of consumers’ requests. Three different drivers for value addition have been considered: packaging, durability, and size options; sensorial features; and sustainability. Results of this investigation have highlighted the added value of several products because of recyclable packaging materials, intermediate or long durability expectations, different available sizes, and good or excellent sensorial performances; (4) Conclusions: There are different value-added coconut-based beverages with interesting perspectives. On the other side, sustainability and eco-friendly policies may be a problem for those products which are produced similarly to non-coconut based beverages. The opportunity of certified organic and/or fair-trade products could help the industry of coconuts in the next future. More research is still needed in this ambit.

Plants have been used in alternative medicine for centuries in the treatment of many diseases with the metabolites they contain. The goal of this work was to investigate the phenolic profile, antioxidant capacity and biological activity of I. helenium subsp. pseudohelenium extracts. Phe-nolic (HPLC) substances in leaf ethanol (L-EtOH), leaf pure water (L-PW), root ethanol (R-EtOH), and root pure water (R-PW) extracts of Inula helenium subsp. pseudohelenium plant were investi-gated. Also, in vitro the antimicrobial (hollow agar), antioxidant (DPPH, ABTS.+, FRAP, CU-PRAC), antiproliferative (MTT assay against HT-29, MCF-7 and L-929), and DNA (Agarose gel electrophoresis) protective activities of the samples were examined. Although gallic acid was not detected in the extracts, the presence of curcumin was detected only in EtOH extracts. L-EtOH exhibited the best antimicrobial activity. According to the antioxidant results, it was found that the L-EtOH extract had an activity profile close to the standard antioxidants in general. It was also found that the L-EtOH extract stabilized the DNA by disrupting the scavenging effect of H2O2+DMSO. According to the antiproliferative activity results, EtOH extracts exhibited the strongest effect, especially against MCF7. When evaluated in general terms, it was found that L-EtOH extract showed better activity than other extracts. It is important to conduct more in vivo and in vitro studies after isolating the active components of extracts e.g. L-EtOH, which have good effects in terms of biological activity.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

Reactions of picolinamides with 1,3-propanesultone in methanol followed by the treatment with ketones led to a series of previously unknown chemical transformations, yielding first pyridinium salts (2a-f) with a protonated endocyclic nitrogen atom and then heterocyclic salts (3a-j) containing a 4-imidazoline ring. The structures of intermediate and final products were determined by IR and 1H, 13C NMR spectroscopy and X-ray study. The effects of the ketone and alcohol structures on the product yield were studied by quantum-chemical calculations. The stability of salts 3a-j towards hydrolysis and alcoholysis makes them excellent candidates for the search of new types of biologically active compounds.

Band structure calculations using the spin-polarized relativistic Korringa-Kohn-Rostoker (SPRKKR) band structure method have been performed to determine the intrinsic magnetic properties (magnetic moments, magneto-crystalline anisotropy -MAE and Curie temperatures) of the Fe5-x-yCoxMySiB2 (M = Re, W) alloys. The general gradient approximation for ex-change-correlation potential and the atomic sphere approximation (GGA ASA) have been em-ployed. Previous studies showed that the Co doping is turning the in-plane into axial anisotropy for a certain doping range, whilst the 5d doping enables a strong spin-orbit coupling of Fe-3d and M-5d states which is needed to enhance the MAE. The theoretical calculations aim to find the dependence of the anisotropy constant K1 for combined Co and M doping, building a two-dimensional (2D) map of K1 for 0 ≤ x ≤ 2 and 0 ≤ y ≤ 1. Similar theoretical 2D maps for magnetization and Curie temperature vs. Co and M content (M = W and Re) have been built, allowing to select alloy compositions with enhanced values of uniaxial anisotropy, magnetization and Curie temperature. Magnetic properties of Fe4.1W0.9SiB2 alloy that meets the selection criteria for axial anisotropy K1 > 0.2 meV/f.u., Curie temperature Tc > 800 K determined by mean field approach and magnetization µ0Ms > 1 T are discussed.

Numerous innovative advancements in dressing technology for wound healing have emerged. Among the various types of wound dressings available, hydrogel dressings, structured with a three-dimensional network and composed of predominantly hydrophilic components, are widely used for wound care due to their remarkable capacity to absorb abundant wound exudate, maintain a moisture environment, provide soothing and cooling effects, and mimic the extracellular matrix. Composite hydrogel dressings, one of the evolved dressings, address the limitations of traditional hydrogel dressings by incorporating additional components, including particles, fibers, fabrics, or foams, within the hydrogels, effectively promoting wound treatment and healing. The added elements enhance the features or add specific functionalities of the dressings, such as sensitivity to external factors, adhesiveness, mechanical strength, control over the release of therapeutic agents, antioxidant and antimicrobial properties, and tissue regeneration behavior. They can be categorized as natural or synthetic based on the origin of the main components of the hydrogel network. This review focuses on recent research on developing natural polysaccharide-based composite hydrogel wound dressings. Their preparation and composition, the reinforcement materials integrated into hydrogels, and therapeutic agents are also explored. Furthermore, their features and the specific types of wounds where applied are discussed as well.

The primary objective of this study is to synthesize, elucidate the structural properties, and ex-plore the biological activity of novel metal complexes derived from 6-methyl-2-thiouracil and 6-propyl-2-thiouracil. The paper outlines a synthesis method and assesses the antimicrobial activ-ity of newly formed Cu(II) and Pd(II) complexes with two substituted 2-thiouracil ligands. The structural attributes of these newly developed compounds are thoroughly discussed based on data derived from melting point analysis, MP-AES for Cu and Pd, UV-Vis, IR, ATR, 1H NMR, 13C NMR and Raman spectroscopy. The interpretation of the complex spectra is assisted by the data for 6-methyl-2-thiouracil and 6-propyl-2-thiouracil obtained from 1H-1H COSY, DEPT-135, HMBC and HMQC spectra. In addition, the antimicrobial activity of these complexes and the free ligands are assessed against both Gram-positive and Gram-negative bacteria, as well as yeasts.

The layered oxyselenide BiCuSeO has garnered significant interest because of its ability to exhibit low thermal conductivity and a high Seebeck coefficient. This study involved the preparation of Bi1−xNaxCuSeO1−xFx(x=0, 0.05, 0.10, 0.15, and 0.20) ceramics through the processes of high energy ball milling and cold isostatic pressing. A systematic study was conducted to investigate the impact of co−doping Na/F on the thermoelectric performance of BiCuSeO ceramics. Replacing Bi3+ with Na+ results in the introduction of a considerable amount of holes, leading to a notable enhancement in the electrical conductivity and power factor. The conductivity was significantly increased from 9.10 S cm−1 in the pure BiCuSeO to 94.5 S cm−1 in Bi0.85Na0.15CuSeO0.85F0.15 at 323 K. At 823 K, the power factor of the Bi0.85Na0.15CuSeO0.85F0.15 sample achieved 44.8×10−5 W/ m K2. Moreover, the Bi1−xNaxCuSeO1−xFx ceramics exhibit a minimum thermal conductivity of 0.43 W m−1 K−1. As a result, the Bi0.85Na0.15CuSeO0.85F0.15 sample achieves a maximum ZT value of 0.78, which is 7.09 times greater than that of the pure BiCuSeO sample (0.11) .

Photodynamic therapy (PDT) has garnered significant attention in the fields of cancer treatment and drug-resistant bacteria eradication due to its non-invasive nature and spatiotemporal controllability. Iridium complexes have captivated researchers owing to their tunable structure, exceptional optical properties, and substantial Stokes displacement. However, most of these complexes suffer from aggregation-induced quenching, leading to diminished luminous efficiency. In contrast to conventional photosensitizers, photosensitizers exhibiting aggregation-induced luminescence (AIE) properties retain the ability to generate a large number of reactive oxygen species when aggregated. To overcome these limitations, we designed and synthesized a novel iridium complex named Ir-TPA in this study. It incorporates quinoline triphenylamine cyclomethylated ligands that confer AIE characteristics for Ir-TPA. We systematically investigated the photophysical properties, AIE behavior, spectral features, and reactive oxygen generation capacity of Ir-TPA. The results demonstrate that Ir-TPA exhibits excellent optical properties with pronounced AIE phenomenon and robust capability for producing singlet oxygen species. This work not only introduces a new class of metal iridium complex photosensitizer with AIE attributes but also holds promise for achieving remarkable photodynamic therapeutic effects in future cellular experiments and biological studies.

Antimicrobial resistance (AMR) has become a worldwide health problem. Consequently, there is a global interest in the study of the antimicrobial activity of natural compounds as an alternative to antibiotics. One of the possibilities studied during the last years is the use of bacteriophages and their derived proteins. More specifically, phage lytic proteins or endolysins are specific enzymes that cause cell lysis and can be easily produced and purified after overexpression in bacteria. However, one of the major disadvantages of these proteins is their sensitivity to some environmental conditions that can reduce their efficiency. The use of vesicles for endolysin encapsulation could help overcome this disadvantage, offering an additional protection to the protein and allowing its controlled release and long-term stability.

Biomimetic materials are substances that replicate natural structures. There are several methods for producing such materials with highly developed surfaces from a wide range of polymers, but electrospinning is of particular interest due to its simplicity of implementation and the ability to modify the produced fibrous materials resembling structures found in living organisms. This study explores new biomimetic materials based on polyhydroxyalkanoates, specifically poly-3-hydroxybutyrate, modified with chlorophyll derivatives. The research investigates the impact of chlorophyll derivatives on the morphology, supramolecular structure, and key properties of nonwoven materials. The obtained results are of interest for the development of new biomimetic environmentally friendly materials for biomedicine with special properties.

This study aimed to evaluate and compare the mechanical properties of three CAD-CAM monolithic esthetic zirconia (Ceramill® Zolid FX Multilayer (ZF), IPS e.max® ZirCAD MT Multi (ZM), and KATANATM STML (KS)) with a CAD-CAM lithium disilicate glass-ceramic (IPS e.max® CAD LT (MC)) as control. 80 samples (20/group) were milled, sintered, and subjected to a three-point bending test (3-PBT) to measure flexural strength and elastic modulus; Vickers indentations were used to measure microhardness. The numerical outcomes were analyzed using one-way ANOVA with a statistical significance set at <0.05. Zirconia showed superior mechanical properties compared with lithium disilicate (P<0.05). ZM had the highest values of flexural strength (P<0.05), KS and ZM showed significantly higher elastic modulus values than ZF (P<0.05), and ZF and KS microhardness values were significantly higher than ZM (P<0.05). Monolithic multi-layered zirconia had enhanced mechanical properties when compared with lithium disilicate and can be a predictable replacement in clinical applications.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

Reducing meat consumption is better for the environment. Unfortunately, commercial plant-based meat substitutes are often more expensive than meat and thus have not seen widespread adoption. This paper analyzes commercially-available spirulina, soy, pea, and brown rice protein isolates characteristics to provide data for non-meat protein cost reductions. Thermal and rheological properties, viscosity, density, and particle size distribution are analyzed for further study on alternative protein-based food processing. Differential scanning calorimetry analysis produced dry amorphous-shaped curves and paste curves with a more distinct endothermic peak. Extracted linear temperature ranges for processing in food production for spirulina was 70-90ºC; soy protein was 87-116ºC; pea protein was 67-77ºC; and brown rice protein was 87-97ºC. Viscosity analysis determined each protein material was shear-thinning and that viscosity increased with decreased water concentration, with rice being an exception to the latter trend. The obtained viscosity range for spirulina was 15,100-78,000cP; soy protein was 3,200-80,000cP; pea protein was 1,400-32,700cP; and brown rice protein was 600-3,500cP. The results indicate that extrusion is a viable method for further processing of the protein isolates as this technique has a large temperature operating range and variable screw speed. Data provided here can be used to make single or multi-component protein substitutes.

Intrauterine adhesions (IUA) has become one of the main causes of female infertility, how to effectively prevent postoperative re-adhesion has been a clinical challenge. In this study, a mussel-inspired dual-network hydrogel was proposed for postoperative anti-adhesion of IUA. First, calcium alginate/polyacrylamide (CA-PAM) hydrogel was prepared by covalent and Ca2+ cross-linking. Benefiting from abundant phenolic hydroxyl groups, polydopamine (PDA) was introduced to further enhance the adhesion ability and biocompatibility. This CA-PAM hydrogel immersed in 10 mg/mL dopamine solution possessed remarkable mechanical strength (elastic modulus > 5 kPa) and super stretchability (with a breaking elongation of 720%). At the same time, it shown excellent adhesion more than 6 kPa. Surprisingly, the coagulation index of the hydrogel was 27.27 ± 4.91, demonstrating attractive coagulation performance in vitro and the potential for rapid hemostasis after surgery.

This work presents the synthesis and self-organization of the calamitic fluorinated mesogen, 1,1,2,2-tetrafluoro-2-(1,1,2,2-tetrafluoro-4-iodobutoxy)ethanesulfonic acid, a potential model for perfluorosulfonic acid membranes (PFSA). The compound is derived in three steps from 1,1,2,2-tetrafluoro-2-(1,1,2,2-tetrafluoro-2-iodoethoxy)ethanesulfonyl fluoride, achieving an 78% overall yield. The resulting compound exhibits intricate thermal behavior. At 150 °C, a crystal-to-crystal transition is observed due to the partial disordering of calamitic molecules, which is followed by isotropization at 218 °C. Upon cooling, sample ordering occurs through the formation of large smectic liquid crystalline phase domains. This thermotropic state transforms into a layered crystal phase at lower temperatures, characterized by alternating hydrophilic and hydrophobic layers. Using X-ray diffraction, crystalline unit cell models at both room temperature and 170 °C were proposed. Computer simulations of the molecule across varying temperatures support the idea that thermal transitions correlate with a loss of molecular orientation. Importantly, the study underscores the pivotal role of precursor self-organization in aligning channels during membrane fabrication, ensuring controlled and oriented positioning.