With the development of free trade port in Hainan Island, the construction of tourist roads around the island is also in full swing. Under the weather conditions of strong typhoon and rainstorm in Hainan, the highway cutting slope built on the coastal weak sandy terraces has strong sand loss and is easy to be scour by rainfall. MICP green spray irrigation solidification technology is used to strengthen the sandy cutting, and pore water pressure monitoring is carried out on the slope model during MICP solidification and rainfall scour. Combined with the model pore water pressure and flow slip failure pattern, dynamic analysis was carried out. The results show that MICP sprinkler irrigation technology can solidified the surface of the slope model in a short time, and the cementation depth of the model reaches 4cm after three sets of rotation reinforcement. The surface reinforcement effect is good, and the sand samples are closely connected. Under the erosion effect of simulated rainfall intensity, the sand loss of the slope is weakened, and no sand binding damage occurs, and the integrity is enhanced. Due to the cementation between sand grains, most of the rainfall was converted into runoff, and the slope slid after 150s. When the slope began to slip, the leading edge of the slope model lost sand and unloaded, and the failure mode was graded creep slip failure. Finally, the slope was divided into several blocks due to the continuous expansion of cracks after the slope failure. The erosion stability of the sandy slope under heavy rains is optimized and the sand loss is prevented effectively. In this study, a new method of MICP remediation techniques is proposed, which provides a new test basis for the application of MICP technology in practical engineering.

Aquifer water is the key staple to develop successful sustainable agricultural activity in newly reclaimed areas in Egypt. Monitoring irrigation water quality is necessary for a proper planning of this exhaustible resources. This work aims to evaluate the groundwater quality in the western newly reclaimed areas of Beni-Suef governorate. Fifty aquifer water sample were collected from wells scattered in the arid western Beni-Suef fringes during May of 2022. Water chemical analyses were conducted to estimate the parameters of Irrigation Water Quality Index (IWQI) namely the Electrical Conductivity (EC), Sodium (Na+), Chloride (Cl-), Bicarbonate (HCO3-) and the Adjusted percentage of Absorbed Sodium (SARo). The Inverse Distance Weighted (IDW) technique used to map the spatial distribution of aquifer water chemical characteristics and IWQI. The results showed that EC values were high in the south of the study area and decreased at its north and east borders. The results showed that the average of dissolved cations and anions were 236.4, 102, 77.5, 106.2, 309.6, 148.1 and 113 meq/l for Ca2+, Mg2+, Na+, K+, SO42-, HCO3-, and Cl-, respectively. Regarding to IWQI, its' values ranged from 28 to 81. Two-thirds of the study area classified as having moderate limitations for sustainable irrigation purposes. Furthermore, one-thirds of the area classified as having high restrictions.

Empirical Orthogonal Functions (EOF) analysis between the anomalies of Lake Titicaca water levels (WLs) and the Pacific Interdecadal Oscillation (IPO) reveals a correlation coefficient of 0.71 between the WLs and the principal component (PC1). These findings demonstrate the high accuracy of the IPO in representing the positive and negative phases of the water levels. By utilizing wavelet functions, we identified multi-decadal variability with periods ranging between 20 and 30 years. The statistical techniques employed indicate a relationship between IPO and ENSO; however, they operate on different timescales of climate variability. The IPO exhibits longer-term variability, typically spanning 20-30 years, while ENSO events occur on average every 2-7 years. Nevertheless, the IPO has the ability to modulate the strength and frequency of El Niño and La Niña events, and vice versa. During the positive phase of the IPO, there is a tendency for more frequent and intense El Niño events, accompanied by fewer La Niña events. This can be attributed to warmer sea surface temperatures in the central and eastern Pacific, which create favorable conditions for El Niño development. Conversely, during the negative phase of the IPO, there is a tendency for more frequent and intense La Niña events, with fewer occurrences of El Niño events, due to cooler sea surface temperatures in the central and eastern Pacific.

The Kuroshio Extension(KE) System exhibits highly energetic mesoscale phenomena, but the impact of mesoscale eddies on marine ecosystems and biogeochemical cycling is not well understood. This study utilizes remote sensing and Argo floats to investigate how eddies modify surface and subsurface chlorophyll (Chl-a) concentrations. On average, cyclones (anticyclones) induce positive (negative) surface Chl-a anomalies, particularly in winter. This occurs because cyclones (anticyclones) lift (deepen) isopycnals and nitrate into (out of) the euphotic zone, stimulating (depressing) the growth of phytoplankton. Consequently, cyclones (anticyclones) result in greater (smaller) subsurface Chl-a maximum (SCM), depth-integrated Chl-a, and depth-integrated nitrate. The positive (negative) surface Chl-a anomalies induced by cyclones (anticyclones) are mainly located near (north of) the main axis of the KE. The second and third mode represent monopole Chl-a patterns within eddy centers corresponding to either positive or negative anomalies, depending on the sign of the principal component. Chl-a concentrations in cyclones (anticyclones) above the SCM layer are higher (lower) than the edge values, while those below are lower (higher), regardless of winter variations. The vertical distributions and displacements of Chl-a and SCM depth are associated with eddy pumping. In terms of frequency, negative (positive) Chl-a anomalies account for approximately 26% (18%) of the total cyclones (anticyclones) across all four seasons. The opposite phase suggests that nutrient supply resulting from stratification differences under convective mixing may contribute to negative (positive) Chl-a anomalies in cyclone (anticyclone) cores. Additionally, the opposite phase can also be attributed to eddy stirring, trapping high and low Chl-a, and/or eddy Ekman pumping. Based on OFES outputs, the seasonal variation of nitrate from winter to summer primarily depends on the effect of vertical mixing, indicating that convective mixing processes contribute to an increase (decrease) in nutrients during winter (summer) over the KE.

This paper presents an overview of EREMI, a two-year project funded under ERASMUS+ KA203, and its results. The project team's main objective was to develop and validate an advanced interdisciplinary higher education curriculum, which includes lifelong learning components. The curriculum focuses on enhancing resource efficiency in manufacturing industries and optimizing poorly or non-digitized industrial physical infrastructure systems. The paper also discusses the results of the project, highlighting the successful achievement of its goals. EREMI effectively supports the transition to Industry 5.0 by preparing a common European pool of future experts. Through comprehensive research and collaboration, the project team has designed curriculum that equips students with the necessary skills and knowledge to thrive in the evolving manufacturing landscape. Furthermore, the paper explores the significance of EREMI's contributions to the field, emphasizing the importance of resource efficiency and system optimization in industrial settings. By addressing the challenges posed by under-digitized infrastructure, the project aims to drive sustainable and innovative practices in manufacturing. All five project partner organisations have been actively engaged in offering relevant educational content and framework for decentralised sustainable economic development in regional and national contexts through capacity building at local level. A crucial element of the added value is the new channel for feedback from students. The survey results, which are outlined in the paper, offer valuable insights gathered from students, contributing to the continuous improvement of the project.

Water pollution is a common problem for dams situated within an urban or agricultural catchment. This can negatively affect the hydro ecosystem, drinking, recreational and other uses of water. In this study, the drinking water quality class of the Roodeplaat Dam, South Africa which faces pollution problems was modeled using machine learning algorisms in Python Jupyter Notebook 6.0.0. Eleven monthly water quality parameters recorded at five sampling stations from January 1981 to September 2017 were used for training and testing the model. Five machine learning classifiers: Gaussian Naïve Bayes (GNB), K-nearest neighbors (KNN), Decision Tree (DT), Support Vector Machines (SVM), and Linear Regression (LR) at a test size of 20%, 25%, 30%, and 40% were used to classify water into five classes (Excellent to Very bad). It was investigated that the dam water has only three classes good, medium, and bad. The prediction accuracies of machine learning algorithms from the highest to the lowest were 96.39%, 96.17%, 92.25%, 90.20, and 54.19% for KNN, DT, SVM, GNB, and LR, respectively. Therefore, KNN at a test size of 30% was recommended to classify the water quality of Roodeplat Dam accurately. Hence, machine learning algorithms can be used to identify the class of water quality before the water is treated and distributed for drinking use.

Forest ecosystems provide diverse services and values that contribute to human well-being. Although high proportion of species is still undiscovered, tropical forests alone are thought to host more than 50% of the world’s biodiversity. Beyond supporting via direct use of products like timber, fiber and biomass energy, they play an important role in providing a wide range of ecosystem services such as regulating water flow and quality, water purification, improving infiltration, fresh water, erosion control, carbon sequestration and sedimentation control. They are one of the important parts of terrestrial and the largest carbon pool, occupying an integral position in the global carbon cycle. However, these days, deterioration of nature and forest biodiversity is a severe danger to the global environment. This will be accompanied by increased strains on food supply, causing increased pressure on already delicate ecological systems. Thus, better forest management strategies are necessary for managing forests sustainably. Nevertheless, little is known regarding the existing forest management approaches and their associated benefits and challenges. Multidisciplinary approaches are needed to achieve sustainable management of forests. These can be accomplished if suitable forest management innovations are put in place. Various technologies can also be adopted through applying different forest assessment tools like remote sensing using light detection and ranging technology (LiDAR) in forest management. Harnessing such technologies will definitely result in providing increased socio-economy as well as improved environmental sustainability. However, the speed of transformation depends much on level of commitment of stakeholders including policy makers. As a result, this review is intended to explore existing forest management innovations which are suitable both ecologically as well as socio-economically. This shows that while there is a lot to be improved, there are already developed forest management innovations that are already in use including PFM and MFM, which helps to achieve SFM. Key words: Sustainable, forests, management, innovations, participatory, growing stock,

This work estimates yield losses due to drought events in mountain grasslands in north-eastern Italy, laying the groundwork for index-based insurance. Given the high correlation between Leaf Area Index (LAI) and grassland yield, we exploit LAI as a proxy for yield. We estimate LAI by the Sentinel-2 biophysical processor and we compare different gap-filling methods, including time-series interpolation and fusion with Sentinel-1 SAR data. We derive a Forage Production Index (FPI) as the growing season cumulate of the daily product between LAI and a meteorological water stress coefficient. Finally, we calculate the drought index as the anomaly of FPI. The validation of Sentinel-2 LAI with ground measurements showed RMSE of 0.92 [m2 m-2] and R2 of 0.81, on average over all the measurement sites. The comparison between FPI and yield showed R2 of 0.56 at the pixel scale and R2 of 0.74 at the parcel scale. The developed prototype FPI index was used at the end of the growing season of the year 2022 for calculating the payments of an experimental insurance scheme that was proposed to a group of farmers in Trentino-South Tyrol.

Sustainable supply chains have become increasingly crucial to address environmental and social challenges faced by societies worldwide. Last-mile delivery, which involves delivering products from a distribution center or warehouse to the final destination, typically a consumer's doorstep, is an essential component of the supply chain. However, it faces numerous challenges such as traffic congestion, air and noise pollution, and carbon emissions. This research paper explores the viability of last-mile delivery solutions for sustainable supply chains. The study reviews the literature on last-mile delivery challenges, sustainable last-mile delivery solutions, and case studies of sustainable last-mile delivery solutions. The results indicate that innovative last-mile delivery solutions, such as electric vehicles, cargo bikes, and drones, have the potential to reduce environmental impact and improve the efficiency of last-mile delivery while enhancing social equity. Additionally, partnerships between different stakeholders, including governments, logistics companies, and consumers, can contribute to the development of sustainable last-mile delivery solutions. The study concludes that sustainable last-mile delivery solutions are essential to achieving sustainable supply chains and recommends further research to explore the economic feasibility and scalability of these solutions.

Mangrove creeks adjoining typical riverine mangrove forests is known to be a net source of CO2 and dissolved inorganic carbon (DIC) to the ocean due to the decomposition of rich organic carbon in the soil; such information is limited in fringe mangroves. This study aims to clarify the difference in carbonate processes between the two types of mangrove forests. We conducted continuous monitoring of the partial pressure of carbon dioxide (pCO2) and measured carbonate chemistry parameters (total alkalinity (TA) and DIC) in two types of mangrove areas located in Okinawa, Japan. The result showed that the maximum pCO2 reached 5242 µatm in the Fukido River estuary (a riverine mangrove), whereas it was only 765 µatm on the Yubu coast (a fringe mangrove). The measured maximum TA and DIC values were 3285 µM and 3283 µM in the Fukido River estuary and 3162 µM and 2977 µM on the Yubu coast. These indicate that pCO2 on the Yubu coast was maintained at low values by the carbonate buffering capacity even when TA and DIC increased rapidly. The mangroves on the Yubu coast grow on dead corals and coral soils. It was suggested that the DIC/TA ratio was constantly kept at approximately 0.9 due to TA production by the dissolution of calcium carbonate (CaCO3), which resulted in lower pCO2.

Ambitle in the Feni Island group is located at the southeastern end of the NW trending Ta-bar-Lihir-Tanga-Feni (TLTF) island chain, northeastern Papua New Guinea. This island chain is known for the presence of alkaline magmas, geothermal activity, copper-gold mineralization, and mining. The purpose of this study is to present and interpret the petrographic, mineralogical, and geochemical data of the subaerial volcanic rocks from Feni within the context of the tectonic evolution of the TLTF. The TLTF arc is a younger arc situated within the Greater Melanesian Arc, specifically the New Ireland Basin bounded by New Ireland and the extinct Kilinailau Trench. The formation of the TLTF is attributed to post-subduction extensional tectonics relating to the opening of the Manus Basin and the magma is potentially sourced from subduction-modified upper mantle. The main rock types sampled in this study are alkalic and include feldspath-oid-bearing basalt, trachybasalt, phonotephrite, trachyandesite, and trachydacite or quartz-trachyte. Minerals identified include forsteritic olivine, diopside, augite, andesine, anor-thitic plagioclase, nepheline and leucite in the primitive mafic suites whereas the more evolved intermediate and felsic hypabyssal suites contain amphibole, albite, orthoclase, biotite, and either rare quartz or feldspathoids. Amphibole composition is primarily magnesiohastingsite with minor pargasite formed under polybaric conditions. Accessory minerals include apatite, ti-tanite, and Ti-magnetite. Feni magmas are highly enriched in REEs relative to neighboring arcs. Fractional crystallization is the dominant process in the geochemical evolution of the Ambitle lavas. Pyroxene fractionation is dominant in the mafic lavas whereas hornblende fractionation is a major petrologic process within the intermediate suites proven by the presence of LREE enrichment and depletions in MREE and HREE.

Radon (²²²Rn) is the second most common type of lung cancer after smoking. As radon poses a significant risk to human health, radon-affected areas should be to ensure people’s awareness of risk and remediation. The primary goal of this research was to investigate the local natural radioactivity (in soils, water and indoors) because of the presence of tuff outcrops (from middle lower Pleistocene volcanic activity) that naturally produce radioactive gas radon at Cerveteri (Rome, Central Italy). The study area is characterized by the presence of several funerary sites pertaining to the Etruscan Necropolis of Cerveteri, which extends over a volcanic rock plateau. The results of the radon survey highlighted moderate (>16000 Bq/m³) but localized anomalies in soils and medium low (< 200 Bq/m³) values of indoor radon excepting some cases exceeding the threshold (> 300 Bq/m³) recommended by 2013/59 Euratom Directive. Although for thoron (²²⁰Rn) effects on human health, there exist no clinical data, the study of ²²⁰Rn average activity concentration in the soil gas survey has revealed new insights for the interpretation of radon sources that can affect dwellings, even taking into account the considerable difference in the half-lives of the ²²²Rn and ²²⁰Rn.

Wildlife tourism and wildlife trade may appear juxtaposed, but are two, potentially aligning, income generators that could benefit conservation in developing countries. Utilising data sets collated from Madagascar’s Ministère du Tourisme and CITES respectively for the period 2007 to 2018, this study estimated levels of income from wildlife tourism and wildlife trade for Madagascar. Between 2007-2018, tourism reported yearly incomes ranging from a low of US $1.4 million up to a high of US $15.7 million. However, it was unclear what percentage of this figure flowed to benefit local communities. Alternatively, using reported networks for the live wildlife trade, the estimated economic value reaching collectors and/or intermediaries on Madagascar was US $72,299.80 for the period 2007 to 2018. Both revenue generators operated within different geographical areas, with tourism opportunities presenting themselves to communities adjacent NPs, while wildlife trade networks were not restricted to NPs and operated sporadically across Madagascar. Hence, the economic benefits reached different Malagasy participants across the country. The management of both activities needs great care to ensure that environmental impacts and sustainability are core measures on any such activities. Whilst this study shines light on economic values and novel perspectives regarding these two trade types, it also highlighted knowledge gaps. Thus, indicating where much greater research attentions was required to allow better understanding of the specific benefits and risks from engaging with both trade types for local Malagasy people and their environments.

China is rich in coal resources under water bodies. However, for a long time, the safety prediction of high-intensity mining under water bodies is one of the problems encountered by the coal industry. It is of great significance to realize safe mining under water bodies, improve the recovery rate of coal resources and protect reservoir resources. Therefore, this article takes the No. 5 coal seam and No. 11 mining area of Wangwa Coal Mine as the research object, and integrates physical simulation, numerical simulation, theoretical analysis and other methods to study the development height of water-conducting fracture zones in fully mechanized top coal caving mining. Solid-liquid coupling physical simulation test reveals the failure characteristics of overlying strata in goaf and the seepage law of reservoir water under the influence of mining. By comparing the monitoring data of borehole leakage, the measured data obtained by borehole peeping with the height data of water-conducting fracture zone obtained by the traditional empirical formula of three-under standard, the error between the two is as high as -29.39 %. In this case, the variance correction coefficient is used to correct the empirical formula, and on this basis, in order to effectively protect the surface water dam and water body, the mining height of coal seam in the working face with limited height mining is inversely derived. The research results provide a basis for the safety prediction of high-intensity mining under the reservoir dam in the ecologically fragile areas of western China and provide a scientific guarantee for the formulation of safety measures under such conditions.

In order to sustain the marine environment relationship between the environmental factors and marine biota must be investigated. This study aims to study such a correlation in the adjacent waters of Nan Wan Bay, Kenting, Taiwan, and to explore the covariance of environmental factors on marine life (whether they enhance or diminish it). To achieve these objectives, factor analysis was used to identify potential latent variables that could affect the water quality of the adjacent waters, including phytoplankton (quantity), zooplankton (quantity), and fish (quantity and species). These potential variables were named based on the results of past studies and related literature. Finally, a structural equation model (SEM) was constructed to establish a marine ecological model among the potential variables. The factor analysis results revealed that nutrients, upwelling, and primary productivity are the primary factors affecting the environmental changes in the adjacent waters of Nan Wan Bay. The comprehensive SEM showed that nutrients and primary productivity significantly impact plankton. Path analysis indicated that primary productivity has the highest direct effect on the phytoplankton cluster. However, the upwelling has a low significance in its effect on phytoplankton, zooplankton, and fish clusters. Compared to the results of past related studies, the SEM proposed in this study can reflect a considerable degree of change in the waters.

The Feni Island group is located at the southeastern end of the NW trending Ta-bar-Lihir-Tanga-Feni (TLTF) island chain, northeastern Papua New Guinea. This island chain is renowned for hosting alkaline magmas, geothermal activity, copper-gold mineralization and mining. The purpose of this paper is to present the geological observations of Feni Island within the context of the regional tectonic setting and evolution of the TLTF. The TLTF arc is a younger arc situated within the Greater Melanesian Arc, specifically within the New Ireland Basin bounded by New Ireland to the west and the extinct Kilinailau Trench in the east. The formation of the TLTF is attributed to post-subduction extensional tectonics relating to the opening of the Manus Basin and the magma is sourced from subduction-modified upper mantle. Normal, ex-tensional faulting is observed throughout the TLTF.

The way humans use natural resources and especially freshwater, reflects their relationship with nature. It also influences the conceptual Water Resources Management (WRM) model. A historical review shows that the interplay between Humans and Nature is diachronically in constant change between two opposites: conflict and cooperation. Lessons from the past 20.000 years indicate that the WRM model is a function of two main parameters: (1) socio-economics, and (2) climate conditions. Three different Eras of the Humans-Nature relationship have been distinguished: (1) Naturalistic: Nature dominating Humans during the Last Glacial Period (100-10) kyr BC, (2) Dualistic: Nature-Humans cooperation and competition from 10 kyr BC to 1800 AD, and (3) Anthropocentric: Humans dominating Nature from 1800 AD to now. Since 2000, the Integrated WRM (IWRM) model is promoted as state-of-the-art and remains anthropocentric producing huge externalities. Its assessment during the last 20 years has given mixed results and needs to be reformulated. The new model we suggest is based on the dialectical tool for conflict resolution. It unifies Humans and Nature and enhances the social dimension of WRM. After identifying conflicts between stakeholders and the natural laws (eristic part), opposite objectives are unified to harmonize Humans with Nature (dialectical resolution). A case study of flood mitigation illustrates the eristic-dialectical methodology.

This study addresses the challenge of assessing the carcinogenic potential of hazardous chemical mixtures, such as PFAS, which are known to contribute significantly to cancer development. Here, we propose a novel framework called HNNMixCancer that utilizes a Hybrid Neural Network (HNN) integrated into a machine-learning framework. This framework incorporates a mathematical model to simulate chemical mixtures and enables the creation of classification models for binary and multiclass classification and regression. Through extensive experimentation, we demonstrate that our HNN model outperforms other methodologies, including Random Forest, Bootstrap Aggregating, Adaptive Boosting, Support Vector Regressor, Gradient Boosting, Kernel Ridge, Decision Tree with AdaBoost, and KNeighbors, achieving a superior accuracy of 92.7% in binary classification. To address the limited availability of experimental data and enrich the training data, we generate an assumption-based virtual library of chemical mixtures using a known carcinogenic and non-carcinogenic single chemical for all the classification models. Remarkably, in this case, all methods achieve accuracies exceeding 98% for binary classification. In external validation tests, our HNN method achieves the highest accuracy of 80.5%. Furthermore, in multiclass classification, the HNN demonstrates an overall accuracy of 96.3%, outperforming RF, Bagging, and AdaBoost, which achieved 91.4%, 91.7%, and 80.2%, respectively. In regression models, HNN, RF, SVR, GB, KR, DT with AdaBoost, and KN achieve average R2 values of 0.96, 0.90, 0.77, 0.94, 0.96, 0.96, and 0.97, respectively, showcasing their effectiveness in predicting the concentration at which a chemical mixture becomes carcinogenic. Our method exhibits exceptional predictive power in prioritizing carcinogenic chemical mixtures, even when relying on assumption-based mixtures. This capability is particularly valuable for toxicology studies that lack experimental data on the carcinogenicity and toxicity of chemical mixtures. To our knowledge, this study introduces the first method for predicting the carcinogenic potential of chemical mixtures. The HNNMixCancer framework offers a novel alternative for dose-dependent carcinogen prediction. Ongoing efforts involve implementing the HNN method to predict mixture toxicity and expanding the application of HNNMixCancer to include multi-mixtures.

With the urgent need of precise positioning faced by internet of things (IoT) applications, the universality and cost of indoor positioning devices become key factors. Since the 5G network has been widely deployed, new opportunity is brought by tightly fusing the traditional low-cost sensors, i.e., the magnetometer. In this study, using 5G channel state information (CSI) and geomagnetic data, a multi-input convolutional neural network (CNN) localization system was proposed. First, to generate a data tensor that is easy for CNN processing, the raw data was reconstructed individually. Then, to comprehensively incorporate the features of 5G CSI and geomagnetic strength data, the ReLU function was chosen as the activation function of the convolutional layer. After that, a multi-input CNN was trained using the incorporated geomagnetic strength and CSI amplitude in the off-line side, and the trained CNN was recorded as a location fingerprint, which can be used for the user position prediction. Finally, in the online side and using a multi-input CNN, the 2-D coordinates are estimated and tested indoors in a typical conference room scenario. The results showed that longer sampling time of fingerprint data result in better uniqueness of the reference point, while the data collection time of locating points does not need to be long. Taking the positioning efficiency and accuracy into consideration, a sampling time of 3s at the reference point and 0.2s at the locating point are recommended. The positioning accuracy using the proposed method was 1.41 m, with an improvement of 22.9% compared with the 5G positioning, and an improvement of 18.0% compared with the 5G and geomagnetic fusing positioning using single CNN.

The Huayangchuan uranium deposit, located in the west of the Xiaoqinling belt on the southern margin of the North China Craton, is a polymetallic deposit dominated by U, Nb, Pb, and rare earth elements. The Huayangchuan uranium deposit, discovered in the 1950s, has long been known as a carbonatite-type uranium deposit. Recently, new geological work has found uranium mineralisation in many granitic pegmatite veins in the Huayangchuan deposit and adjacent areas. Here, we report a systematic investigation of the petrography, whole-rock geochemistry, zircon U-Pb ages, and in situ Lu-Hf isotopic characteristics of newly discovered U-rich granitic pegmatite veins in the west of Huayangchuan deposit. The petrological results showed that the lithology of the samples is equivalent to that of granite. The U-Pb ages of zircon were 1826.3 ± 7.9 and 1829 ± 11 Ma. Microscopically, the symbiotic characteristics of zircon, betafite, and uraninite exist in the intergranular fissures of K-feldspar and quartz, reflecting metallogenic phenomena in the rock formation process. Almost all whole-rock samples were rich in SiO2 (64.37–70.69 wt.%), total alkalis (K2O+Na2O = 8.50–10.30 wt.%), and Al2O3 (12.20–14.41 wt.%), but poor in Ti2O (0.23–0.73 wt.%), MgO (0.38–0.90 wt.%), P2O5 (0.14–0.83 wt.%), MnO (0.04–0.57 wt.%). Additionally, they showed enrichment of LILEs (such as Rb, Ba, Th, U, and K), depletion of HFSEs (such as Ta, Nb, P, Ti, and Hf), no alkaline dark minerals, and the characteristics are typical of intraplate A1-type granite. The A1-type granite displayed low zircon εHf(t) values (-19.42– -15.02) with zircon two-stage Hf model aged 3.10–2.76 Ga, indicating that the U-rich granitic pegmatite was derived predominantly from partial melting of the ancient continental crust (such as the early Taihua group formed in Archean-Neoarchean). Combined with the above results and regional geological data, the U-rich granitic pegmatite discovered in the Huayangchuan deposit was related to granite magma activity that formed in a post-collisional regime after the Luliang movement in the late Palaeoproterozoic. This study suggests that future uranium prospecting work in this area should focus on late Palaeoproterozoic U-rich granitic pegmatites.

Agroforestry homegardens are integrated arrangements of common vegetable plants in areas close to residences, which follow a structure similar to that of tropical forests, with the cultivation of multiple species to meet the basic needs of families, such as the provision of food and medicine, as well as ensuring an environment for other family activities. Considering the importance of these environments, this work aimed to address the composition and use of plant species in agroforestry homegardens, in order to support society initiatives and government policies to strengthen the management of natural resources and individual and collective well-being in the region. For this, 119 homegardens were studied in the municipalities of Belterra, Mojuí dos Campos and Santarém, in the state of Pará, in the Brazilian Amazonia, comprising five different zones (peri-urban, urban, floodplain, indigenous land and tourist land), obtaining the data via questionnaires and guided visitation by the residents. A total of 5,323 vegetal individual plants were surveyed, distributed in 188 species and 62 botanical families. The data showed that 80.5% of the individual plants are concentrated in 18.6% of the species, with no significant difference in the average of species per homegarden in the five zones. The predominance of species for food use, primarily fruit-bearing, stands out, showing a possible direction for incentive actions and/or for the ordering of public policies and programs aimed at these spaces. Most homegardens have up to 17 plant species; less than half of homegardens have species intended for medicinal use; and there is percentage parity between native plant species and those of exotic origin, where native plants stand out for shading. Agroforestry homegardens play a crucial role in the conservation and cultivation of species for food purposes, with the cultivation or maintenance of plants based on their various purposes, showing distinct profiles of distribution and choice of species, evidencing their socioeconomic and environmental importance. Thus, it is important that these land use systems are valued, investing financial resources in actions and projects aimed at maintaining and enhancing their benefits for the region.

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

Influenced by the quasi-stationary Mei-yu front and the development of mesoscale low vortices on the Mei-yu front, a torrential rain event occurred in Suzhou on July 6, 2020. The 24-hour rainfall recorded by the automatic station exceeded 200 millimeters, with the highest hourly intensity surpassing 70 millimeters, accompanied by thunderstorms and strong winds. This heavy precipitation process was characterized by suddenness, extremity, long duration, high precipitation efficiency, and backward propagation. Using various data sources such as the European ERA5 reanalysis data, ground-based automatic stations, sounding, Doppler weather radar, and wind profile radar, this paper analyzed in detail the circulation characteristics and radar echo structures of this torrential rain event, and further studied the triggering, feature evolution, and maintenance mechanisms of the heavy precipitation.The results show: (1) The continuously strengthening low-level jet stream propagates downward forming an ultra-low-level jet stream. Heavy precipitation is located on the left front side of the jet exit area, where strong convergence and lifting in the boundary layer overlap with the ascending branch of the secondary circulation above the shear line, resulting in heavy precipitation. (2) A supercell storm with intense precipitation produced this heavy rainfall event, characterized by a low centroid of strong echo; echo-free vault, bounded weak echo region, and other supercell structural features. During this event, the high reflectivity factor areas corresponded to high KDP value areas, indicating a large amount of liquid water content. Vertically, the KDP column can track the rainwater mixing ratio well, and its location corresponds to the vicinity of the short-term heavy precipitation occurrence. The high KDP value area mainly consists of numerous precipitation particles, and the vertical vortex wind field structure causes rapid growth of precipitation particles through continuous rolling. Furthermore, it can be found through correlation coefficients (CC) that there are always high-value areas for CC since they correspond to areas of intense precipitation. (3) Continuous triggering of mesoscale convective cloud clusters on the east-west ground convergence line leads to new development and forms a "train effect." Strong frontogenesis in both horizontal and vertical directions triggers and sustains this heavy precipitation event. The significant increase in liquid water and water vapor density has indicative significance for the occurrence of heavy precipitation.

Many drylands around the world have seen both soil and vegetation degradation around watering points. It can be seen in spaceborne imagery as radial brightness belts that fade with distance from the water areas. The study's primary goal was to characterize spatio-temporal land degradation/rehabilitation in the drylands of the southeast Iberian Peninsula. The brightness index of Tasseled Cap was discovered to be the best spectral transformation for enhancing the contrast between the bright-degraded areas near the points and the darker surrounding areas far from and in-between these areas. To comprehend the spatial structure present in spaceborne imagery of two desert sites and three key time periods, semi-variograms were created (mid-late 2000s, around 2015, and 2020). In order to assess spatio-temporal land-cover patterns, a geostatistical model (kriging) was used to smooth brightness index values extracted from 30 m spatial resolution images. To assess the direction and intensity of changes between study periods, a change detection analysis based on kriging prediction maps was performed. These findings were linked to the socioeconomic situation prior to and following the EU economic crisis. The study discovered that degradation occurred in some areas as a result of the region's agricultural activities being exploited.

Temporary streams are a key component of the hydrological cycle in arid and semi-arid regions, but their flow is highly variable and difficult to measure. In this paper, we present a novel approach that could be used to assess the flow of temporary streams and characterize their environmental status. Specifically, we apply the Image Velocimetry method to estimate surface velocity in temporary streams using unmanned aerial vehicles (UAVs) equipped with optical sensors (IV-UAV method). The IV-UAV method enables the easy, safe and quick estimation of the velocity on the water’s surface. This method was applied in different temporary streams in Lesvos Island, Greece. The produced results show that the IV-UAV can be implemented at low discharges, at temporary streams and at small streams. However, there were many occasions that measurements were unable due to various reasons such as dense vegetation or archaeological sites. Despite of this, the proposed methodology could be incorporated in optical protocols which are used to assess the environmental status of temporary streams of Mediterranean conditions. Finally, this would become a valuable tool for understanding the dynamics of these eco-systems and monitoring changes over time.

To understand forest dynamics under today’s changing environmental conditions, it is important to analyze the state of forests at large scales. Forest inventories are not available for all regions, so it is important to use other additional sources of information, e.g. remote sensing observations. Increasingly, remotely sensed data based on optical instruments and airborne LIDAR are becoming widely available for forests. There is great potential in analyzing these measurements and gaining an understanding of forests state. In this work, we combine the new generation radiative transfer model mScope with the individual-based forest model FORMIND to generate reflectance spectra for forests. Combining the two models allows us to account for species diversity at different height layers in the forest. We compare the generated reflectances for forest stands in Finland, in the region of North Karelia, with Sentinel-2 measurements. We investigate which level of forest representation gives the best results. For the majority of the forest stands, we generated good reflectances with all levels forest representation compared to the measured reflectance. Good correlations were also found for the vegetation indices (especially NDVI with R²=0.62). This work provides a forward modelling tool for relating forest reflectance to forest characteristics. With this tool it is possible to generate a large set of forest stands with corresponding reflectances. This opens the possibility to understand how reflectance is related to succession and different forest conditions.

Cooking is a very decentralized and private way of energy consumption in human activities. The existing investigation and statistical analysis can’t effectively calculate the proportion of population relying on clean cooking fuel and utilization technology in the region. Therefore, based on the big data of the earth, this paper adopts the combination of spatial analysis and statistical analysis to determine the survey sample area, and according to the economic conditions, topographic characteristics, national policies for new energy construction and living habits of the provinces and cities under investigation, the questionnaire survey is conducted for the research area to calculate the proportion of the regional population relying on clean cooking fuels and utilization technologies. Taking the south of the Yangtze River in China as an example, the paper effectively calculates that 88.25% of the population depends on clean cooking fuel and technology in this region, of which 89.81% are in urban areas and 79.87% are in rural areas. Analysis of the survey data shows that the proportion of the population using clean cooking fuels and technologies is related to factors such as economic development, income and resource endowment. There is a large urban–rural gap in terms of energy consumption tendency and structure in the south of the Yangtze River in China and cooking energy consumption in rural households also varies from region to region. The technical ideas and conclusions of the paper have high reference application value, which can help promote the upgrading of clean energy utilization and provide data basis for relevant decision and policy making.

Climate change affects water resources through the decrease of rainfall and the increase in temperatures and evapotranspiration. An indirect impact of climate change is also the increase of water uses by human activities. In this review, 320 papers were retrieved, of which 134 spanning five continents impacts and solutions to be used to better understand the effects of climate change on water resources, ecosystems, human health, security and socio-economic aspects were selected. Here, suggestions and proposals by scientists from around the world towards solutions, tips and ideas to deal with climate change and the best solutions for future water management were presented. The main solutions highlighted concern integrated water resources management, political direction, policies, increase in knowledge and new technologies. Furthermore, most of the papers analyzed underline that water resources management needs to incorporate protection and restoration of ecosystems and their services. Nature-based solutions need to be the starting point of new scientific and innovative ways to deal with climate change and towards future climate adaptation. In this complex evolution of the water resource, where is the management of the water resource in Italy going?

The use of nitrogen (N) fertilizers can have detrimental effects on the environment due to nitrate leaching. This study aims to examine the impact of N fertilizer source and application timing on wheat yield and nitrate leaching in various soil textures. A randomized complete block design (RCBD) was employed to conduct the experiment. The treatments consisted of two N fertilizer sources: ammonium nitrate (AN) and urea (NN), applied at three different times throughout the year, with a control treatment. The three application timings were total application before sowing (T₁), total application in spring (T₂), and half the amount before sowing and the other half in spring (T₃). The experiment was conducted in three different soil textures (sandy loam, silty clay loam, and silty clay), with three replications over three growing seasons: 2018-19 (Y₁), 2019-20 (Y₂), and 2020-21 (Y₃). The results indicated significant effects of different soil textures on grain yield. Specifically, the silty clay loam soil differed significantly from the sandy loam and silty clay soils in terms of grain yield. The interaction effects between the N fertilizer source and application timing were also found to be significant for all soil textures (p<0.01). In sandy loam and silty clay soils, the grain yield increased when using the T₃ application timing compared to the silty clay loam soil. Notably, the silty clay loam soil with the T₂ application timing exhibited the highest grain yield, with a yield of 6863.6 kg ha^-1. Furthermore, the study revealed that N fertilizers and their application timing significantly influenced the protein content in the silty clay and sandy loam soils. The protein percentages were 10.76 and 10.93 for the silty clay and sandy loam soils, respectively, following the T₂ treatment. Additionally, ammonium nitrate (AN) demonstrated a noticeable effect on the percentage of grain protein compared to urea (NN). In conclusion, the application timing of N fertilizers had an impact on grain yield and protein content in different soil textures. Moreover, nitrate concentration increased throughout the experiment, with the highest soil nitrate concentration observed in both fertilizer treatments, particularly in the sandy loam soil.

Climate data are important in building a hydrological risk assessment model. The ClimInonda web application enables interactive and dynamic visualizations of different data collected from different weather stations in the study area on a single platform, allowing users to explore and analyze data in an easy way. This can assist decision-makers and stakeholders in understanding the current state of the environment and in identifying areas of flooding risk. Visualizations can include different types of data, such as satellite imagery, weather data, and terrain data, and can be displayed using various techniques, such as heat maps, contour maps, and 3D models by providing easy-to-understand visualizations. The different stations of the Gafsa and Kasserine governorates in the study area are included and other stations of the Algerian territory (Tebessa governorate) are incorporated. This web application also provides the capability to include each user's stations.

This study is describing airborne geophysical survey, carried out in Northeastern Russia (Archangelsk region) in order to aimed at geological mapping of Grib kimberlite pipe, which is known to have strong presence of remanent magnetization. Airborne data were inverted using two techniques, the magnetization vector inversion (MVI) and a QDIK inversion, a proprietary algorithm developed at the Irkutsk State University (ISTU), which allows extracting four parameters from airborne magnetic data (magnetic susceptibility, inclination, declination and Koeniksberger ratio). The inversion results were further analyzed and verified against the known geology of the Grib kimberlite. The study allowed to better map geology of Grib kimberlite using only uninvasive (remote sensing) technology

Change detection with heterogeneous remote sensing images (Hete-CD) plays an important role in practical applications, especially when homogenous remote sensing images are unavailable. However, bitemporal heterogeneous remote sensing images (HRSIs) cannot compare directly to measure change magnitude, and many deep learning methods require large amounts of samples to train the module. Moreover, labeling many samples for land cover change detection with HRSIs is time-consuming and labor-intensive. Therefore, acquiring satisfactory performance of Hete-CD remains a challenge for deep learning networks with very small training samples. In this study, we promote a novel deep-learning framework for Hete-CD to obtain satisfactory performance while the initial samples are very small. We initially design a multiscale network with select kernel-attention module to focus on capturing different change targets with various sizes and shapes. Then, a simple yet effective non-parametric sample-enhanced algorithm based on the Pearson correlation coeffi-cient is promoted to explore potential samples around each initial sample. Finally, the proposed network and sample-enhanced algorithm are fused into one iterative framework to improve the change detection performance with very small samples. Experimental results conducted on four pairs of actual HRSIs indicated that the proposed framework can achieve competitive accuracies with very small samples for initialization when compared with some state-of-the-art methods. For example, the improvement is approximately 3.38% and 1.99% when compared with the selected traditional methods and deep learning methods, respectively.

Soil quality is a factor which is directly related to the sustainability of agricultural production and can be compromised through the use of inadequate management practices. In this work, soil edaphic respiration and changes in microbial biomass promoted by cover crops in an integrated crop-livestock system (ICLS) were evaluated using soil quality indicators by the respirometry method. The design used was completely randomized in a 3x6 factorial scheme and multivariate principal components analysis (PCA) was performed according to MANOVA. The edaphic respiration was determined based on the respirometry technique. From the results, it was found that edaphic soil respiration was significant in the nine evaluation periods, demonstrating the importance of grass cover on this edaphic respiration arising from the biological activity of microorganisms, which is directly related to the amount of organic carbon in the soil. It was concluded that the use of cover crops contributed to producing organic matter in the soil and consequently greater microbial respiratory activity.

Vegetation identification using remote sensing is essential for understanding terrestrial ecosystems and monitoring climate change. This technology by providing high-resolution images of the Earth's surface from satellites, aircraft, and drones has revolutionized the way scientists study and un-derstand vegetation patterns, providing information on the distribution, structure, and health of plant communities in different regions and biomes. However, identifying vegetation in multi and hyperspectral images remains a difficult, time-consuming, and costly process. Traditional methods for vegetation mapping involve the in-terpretation of spectral indices such as the Normalized Difference Vegetation Index (NDVI), alt-hough they often suffer from limitations such as manual interpretation and limited spatial resolution of satellite images. Furthermore, machine learning techniques, artificial neural networks, decision trees, support vector machines, and random forests have shown promising results in identifying and classifying vegetation cover from hyperspectral images. However, due to the need for per-son-nel with specialized expertise, their application on a large scale is still challenging. On the other hand, correlation methods between curves have emerged as powerful and simplified tool for comparing spectral signatures of hyperspectral image pixels and efficiently classifying vegetation in a study area. Pearson's correlation coefficient and spectral angle mapper are among the most common correlation methods used in vegetation mapping. These correlation methods, among many others available, offer an easily implemented and computationally efficient approach, making them particularly useful for applications in developing countries or regions with limited resources. In this article, a comparative study of correlation/distance metrics was conducted for the detection of vegetation pixels in hyperspectral images. The study allowed for the comparison of five distance and/or correlation metrics: direct correlation, cosine similarity, normalized Euclidean distance, Bray-Curtis’s distance, and Pearson correlation. The two metrics that yielded the best accuracy results in vegetation pixel detection were direct correlation and Pearson correlation. Based on the selected methods, a vegetation detection algorithm was implemented and validated on a hyper-spectral image of the Manga neighborhood in Cartagena de Indias, Colombia. The spectral library was utilized for image processing, while the numpy and scipy libraries in the Python programming language were used for the mathematical calculation of correlations. Both the study's approach and the implemented algorithm aim to serve as a reference for conducting detection studies of various material types in hyperspectral images using open-access programming platforms.

Soil moisture maps are essential for hydrological, agricultural and risk assessment applications. To best meet these requirements, it is essential to develop soil moisture products at high spatial resolution which is now made possible using the free Sentinel-1 (S1) SAR (Synthetic Aperture Radar) data. Some soil moisture retrieval techniques using S1 data relied on the use of a priori weather information in order to increase the precision of soil moisture estimates, which required access to a weather forecasting framework. This paper presents an improved and fully automated solution for high-resolution soil moisture mapping in bare agricultural areas. The proposed solution derives a priori weather information directly from the original Sentinel images, thus bypassing the need for a weather forecasting framework. For soil moisture estimation, the neural network technique was implemented to ensure the optimum integration of radar information. The neural networks were trained using synthetic data generated by the modified Integral Equation Model (IEM) model and validated on real data from two study sites in France and Tunisia. Main findings showed that the use of radar signal averaged over grids of a few km2 in addition to radar signal at plot scale instead of a priori weather information, provides good soil moisture estimations. The accuracy is even slightly better comparatively to the accuracy obtained using a priori weather information.

Globally, the intensity and irregularity of weather and climate extremes are increasing due to climate change. In Ethiopia, the occurrence of extreme events has been increasing, reporting severe impacts on environment which led to losses of lives and livelihood of societies. In this study, Heat Wave Magnitude Index daily (HWMId) was used to analysis heat wave magnitude in the Middle Awash Basin of Ethiopia. Gauge data obtained from Ethiopian Meteorological Institution (EMI) for 1981-2022 period and the future projection was taken from Coupled Model Intercomparison Project Phase 6 (CMIP6) under two socioeconomic pathways (SSP 2 and SSP 5) scenarios. The findings clearly showed that the area aggregated annual temperature anomaly increasing each year, 2015 was one of the warmest year on record with an anomaly of +1.8 °C. Severe to extreme heat wave recorded particularly during the last 10 years. For the future projection, under SSP 2-4.5 forcing scenario, the annual average air temperature projected to be warmer, which increasing 1.7 ℃ to 1.8 ℃ during mid-century and 2.3 ℃ to 2.4 ℃ end of century. Meanwhile, for SSP 5-8.5 forcing, the projection indicated an increment of 2.2 ℃ to 2.5 ℃ under mid-century and 4.4 ℃ to 4.8 ℃ end of century. Concerning the severity of heat wave, extreme to very extreme heat wave projected under SSP 2-4.5 forcing scenario and supper extreme heat wave projected under SSP 5-8.5 forcing scenario, respectively. The increase in extreme events may have a negative impact on health, water availability and food security. Therefore, the result of this study are essential for making wise decisions and for developing suitable strategies for climate change adaptation and mitigation that could minimize the risk of unusually extreme weather events.

The study was carried out in zone 7 of Ecuador, in ecosystems of the Southern Montane Evergreen Forest of the Eastern Cordillera of the Andes that goes from 2200 to 3000 masl. In the Evergreen Seasonal Lower Montane Forest of Catamayo-Alamor, which ranges from 1600-2000 meters above sea level and finally in the Semideciduous Foot Montane Forest of Catamayo-Alamor, which ranges from 400-1600 meters above sea level. The objective was to know the occurrence, structure and abundance of J. neotropica. The investigation consisted of collecting secondary information on the occurrence of the species, to later verify it in situ. Six sites with areas ≥ 0.5 hectares were identified, four in the province of Loja and two in the province of Zamora Chinchipe. Regarding the structure, it was determined that there are significant statistical differences as well as in the dasometric variables between one site and another, presenting better growths El Tundo with average values in DAP(cm)= 45.16; G(m2) = 1.41; HT(m)= 19.22; HC(m)= 13; VC(m3) = 3.55; VT(m3) = 5.22. Regarding the Morisita index, the species presents adistribution pattern &gt;1. Regarding abundance, it was determined that Algeria presented a maximum of 297 (ind/ha), and La Victoria 46 (ind/ha) with a minimum.

Remote sensing plays a central role in the assessment of environmental phenomena and has increasingly become a powerful tool for monitoring shorelines, rivers morphology, flood waves delineation and floods assessment. Optical based monitoring and characterization of river evolution at long time scales is a key tool in fluvial geomorphology. However, the evolution occurring during extreme events is crucial for the understanding of the river dynamics under severe flow conditions and requires the processing of data from active sensors to overcome cloud obstructions. This work proposes a cloud-based unsupervised algorithm for the intra-event monitoring of river dynamics during extreme flow conditions based on time series of Sentinel-1 SAR data. The method allows the extraction of multi-temporal series of spatially explicit geometric parameters at high time and spatial resolutions, linking them to the hydrometric levels acquired by reference gauge stations. Intra-event reconstruction of inundation dynamics has led to the estimation of the relationship between hydrometric level and wet area extension and the assessment of bank erosion phenomena. Time series of SAR acquisitions, provided by Copernicus Sentinel-1 satellites, were analyzed to quantify changes in the wet area of a reach of the Tagliamento river under different flow conditions. The algorithm, developed within the Python-API of GEE, first empowers the Sentinel-1 images with the hydrometric level, then involves radiometric slope correction and speckle noise filtering. The Otsu method is then used for image segmentation leading to a water and dry land binary classification. Results support many types of analysis about river dynamics, including morphological changes, floods monitoring and relief efforts and bio-physical habitat dynamics. The results encourage future advancements and applications of the algorithm, specifically exploring SAR data from ICEYE and Capella Space constellations, which offer significantly higher spatial and temporal resolutions compared to Sentinel-1 data.

The goal of this work is to develop a sustainable value chain of carbonaceous adsorbents that can be produced from the solid fibrous digestate (SFD) of biogas plants and further applied in integrated desulphurisation-upgrading (CO2/CH4 separation) processes of biogas to yield high purity biomethane. On this purpose, physical and chemical activation of the SFD derived biochar was optimised to afford micro-mesoporous activated carbons (ACs) of high BET surface area (590-2300 m2g−1) and enhanced pore volume (0.57-1.0 cm3g−1). Gas breakthrough experiments from fixed bed columns of the obtained ACs, using real biogas mixture as feedstock, unveiled that the physical and chemical activation conclude to different types of ACs which are sufficient for biogas upgrade and biogas desulphurisation respectively. Performing breakthrough experiments at three temperatures close to ambient it was possible to define the optimum conditions for enhanced H2S/CO2 separation. It was also concluded that the H2S adsorption capacity is significantly affected by restriction to gas diffusion. Hence, the best performance was obtained at 50 oC and the maximum observed in the H2S adsorption capacity vs the temperature is attributed to the counterbalance between adsorption and diffusion processes.

China promotes nature-based solutions (NbS) as key approaches to addressing climate change, ecosystem damage, and biodiversity loss. However, indigenous and local knowledge (ILK), which is recognized by international scholars as an essential element of successful NbS, has not been thoroughly studied in the Chinese context. By conducting a comprehensive review of Chinese central governmental policies and semi-structured interviews with typical cases, this study finds out diversified sources of ILK and five pathways of ILK integration, including education, supervision, participation, knowledge preservation, and knowledge adoption. An increasing emphasis on community engagement has been driven by central policies such as the ecological civilization, carbon peaking and carbon neutrality goals. From a practical perspective, consistent core ideas of ILK exist in selected typical Chinese cases and studies in other countries, namely co-existence and reciprocity with nature. While supportive central policies can set the scene, ILK integration could not be realized without local governmental endorsement, context-based implementation, and long-term multi-stakeholder participation. Furthermore, this study also figures out a potential deficiency in terms of realizing effective ILK integration in mainstream and conventional practices, which can be further investigated by future studies.

Within this paper, a machine learning algorithm is used to investigate the importance of certain setpoints and parameters in the filtration processes of a large-scale water treatment facility. Previously, a model for the filtration process based on Run-to-Run Control was proposed and tested against sample data from the treatment plant, but it was quickly found that such a model was incompatible for successfully computing setpoints of operation which minimize the energy cost of running the filtration systems. The machine learning model described herein is an attempt to elucidate the importance of the available data on the filtration systems and to identify the most important variables that influence the filtration run time.

The acquisition of regional, 1 metre resolution LIDAR in the PNG Highlands combined with 3D modelling in MoveTM has revolutionized our understanding of the evolution of the Porgera gold mine and areas of new potential. The new 3D model demonstrates active pull-apart basins along a regional transfer during ongoing fold and thrust deformation. When overlain on regional aeromagnetic data, new potential is revealed. The Porgera gold mine is one of the richest in the world and lies in a wide valley at an elevation of 2800m surrounded by mountains up to 4000m high in the middle of the PNG Highlands. It lies along a major lineament, the Porgera Transfer Zone (PTZ), cutting across the orogen that is associated with a 50 km offset of the ophiolite belt. To the NW of the mine there is an extensive belt of low- to high-grade metasediments that formed in deep water during Jurassic rifting, but were metamorphosed during Eocene subduction to the north. Subduction ceased due to accretion of the Sepik Terrane which caused inversion and mild erosion of the Porgera area. The Late Oligocene onset of wrenching in the Mobile Belt to the north placed that area into extension, emplacing metamorphic core complexes, and led to regional subsidence in the Early Miocene. Collision of the margin with the Melanesian Arc in the Middle Miocene caused Late Miocene to Pliocene orogenesis creating the broad mountain belt that we see today, that is still active, as shown by the 2018 MW 7.5 earthquake. Regional mapping of the area using high resolution LIDAR in association with limited field mapping, analysis of gravity and magnetics data and drilling of 300-500m deep core-holes has allowed development of a detailed 3D structural model. The Porgera valley is constrained laterally by the Eastern Boundary and Western Boundary dextral strike-slip faults that lie along the PTZ cutting across the orogeny. However, whilst the position and nature of the faults is clear, due to bending, fracturing and offset of major synclines and anticlines, the faults do not crop-out as significant through-going features. Rather, the dextral offset of basement is soft-linked to the Tertiary limestones at surface due to intervening thick, ductile Cretaceous shales. Fold and thrust structures are ubiquitous in the Tertiary limestones, but the youngest structural features are large extensional faults, particularly around the Porgera valley. The intrusive underlying the Porgera ore-body was emplaced at 6.0+-0.3 Ma, the time of maximum compression during orogenesis. At this time the Eastern Boundary fault and Western Boundary fault were both active allowing a pull-apart basin to form locally along the PTZ at the south-eastern boundary of the Jurassic metasediments. This enabled emplacement of the intrusive. The gold-bearing fluids from the intrusive and metasediments were brought up through the Mesozoic muds to the contact with the Paleogene carbonates where the Porgera ore body was emplaced.

The study of fractures in the subsurface is very important in unconventional reservoirs since they are the main conduits for hydrocarbon flow. For this reason, a variety of equivalent medium theories have been proposed for the estimation of fracture and fluid properties within reservoir rocks. We experimentally investigated the feasibility of applying the Galvin model in fractured tight stones. For this proposal, three artificial fractured tight sandstone samples with the same background porosity (11.7% ± 1.2%) but different fracture densities of 0.00, 0.0312, and 0.0624 were manufactured. The fracture thickness was 0.06 mm and the fracture diameter was 3 mm in all the fractured samples. Ultrasonic P- and S-wave velocities were measured at 0.5 MHz in a laboratory setting in dry and water-saturated conditions in directions at 0°, 45°, and 90° to the fracture normal. The results were compared with theoretical predictions of the Galvin model. The comparison showed that model predictions significantly underestimated P- and S- wave velocities as well as P-wave anisotropy in water-saturated conditions, but overestimated P-wave anisotropy in dry conditions. By analyzing the differences between the measured results and theoretical predictions, we modified the Galvin model by adding the squirt flow mechanism to it and used the Thomsen model to obtain the elastic moduli in high- and low-frequency limits. The modified model predictions showed good fits with the measured results.

With the proliferation and development of social media platforms, social media data has become an important source for acquiring spatio-temporal information on various urban events. Providing accurate spatio-temporal information for events contributes to enhancing the capabilities of urban management and emergency response. However, existing research on mining spatio-temporal information of events often focuses solely on textual content, neglecting data from other modalities such as images and videos. Therefore, this study proposes an innovative spatio-temporal information extraction method for multi-modal social media data (MIST-SMMD), which extracts the spatio-temporal information of events from multi-modal data on Weibo at coarse and fine-grained hierarchical levels, serving as a beneficial supplement to existing urban event monitoring methods. This paper takes the "July 20th Zhengzhou Heavy Rainfall" incident as an example, to evaluate and analyze the effectiveness of the proposed method. The results indicate that in the coarse-grained spatial information extraction using only textual data, our method achieves a Spatial Precision of 87.54% within a 60m range, and reaches 100% Spatial Precision for ranges beyond 200m. For fine-grained spatial information extraction, the introduction of other modal data such as images and videos results in a significant improvement in Spatial Error. These results demonstrate the ability of the MIST-SMMD method to extract spatio-temporal information from urban events at both coarse and fine levels, and confirms the significant advantages of multi-modal data in enhancing the precision of spatial information extraction.

The spatiotemporal variations of rainfall erosivity in the Hengduan Mountains, charac-terized by rugged terrain and high potential soil erosion risks, over the past 30 years was exam-ined. The changing trends of rainfall erosivity for 2025-2040 was also be investigated under the comprehensive scenario of moderate socio-economic development (SSP2-4.5) combined with me-dium-low radiative forcing, using four global climate models (GCMs) based on CMIP6. The results indicated that: (1) The annual distribution of rainfall erosivity in the Hengduan Mountains exhib-ited significant seasonal variations, with the order of erosivity being summer > autumn > spring > winter on a seasonal scale. (2) Over the past 30 years, there has been a slight decrease in annual precipitation and a slight increase in rainfall erosivity, with periodic extreme values occurring every 6-8 years. (3) Rainfall erosivity showed a decreasing gradient from southeast to northwest in terms of spatial distribution. There was a significant positive correlation between rainfall ero-sivity and precipitation, while a significant negative correlation existed with elevation in the ver-tical direction. Moreover, there was an increasing trend of rainfall erosivity in the northeastern part of the Hengduan Mountains and a decreasing trend in the southern region. (4) Under the joint driving forces of increased precipitation and erosive rainfall events, rainfall erosivity in the future is expected to significantly increase, posing a more severe risk of soil erosion in the Heng-duan Mountains.

Building outlines extracted from remote sensing images and raster maps often have irregular boundaries, redundant points, inaccurate positions, and unclear turns due to factors such as image quality, complexity of the surrounding environment, and extraction methods. This study proposes a regularization algorithm for right-angled polygon building outlines with jagged edges. First, the minimum bounding rectangle of the building outline is established and populated with a square grid based on the smallest visible length principle. An overlay analysis is then applied to the grid and original building to extract the turning points of the outline. Finally, the building orientation is used as a reference axis to sort the turning points and reconstruct the simplified building outline. Analysis of the experimental results shows that the proposed simplification method enhances the morphological characteristics of building outlines, such as parallelism and orthogonality, while considering simplification principles, such as the preservation of direction, position, area, and shape of the building. The proposed algorithm provides a new regularization method for building outlines with jagged edges.

Drag-dominant tidal turbine energy holds tremendous clean energy potential but faces significant hurdles as unsuitability of Disk Actuator theory due to the varying swept blockage area, unaccounted bypass flow downstream interaction and rotor parasitic drag whereas Blade Element Momentum theory is computably effective for majorly 3-blade lift-dominated aerofoil. This study proposes a novel method to find the optimal TSR of any turbine with a cost-effective and user-friendly Moment Balancing algorithm to support robust tidal energy development. Performance analysis CFD study of Pinwheel and Savonius tidal turbines was carried out. Dynamic TSR matrix was developed with varying rotational speeds and fluid velocities for reliability, unlike previous works simulated at a fixed fluid velocity. Novel parameters such as thrust and idle moment are introduced as functions of only inlet fluid velocity and rotational speed respectively. These relationships are verified through regression analysis, and the turbines' net moment equations are established based on these parameters. Rotational speed was a reliable predictor for Pinwheel's idle moment, while inlet velocity was a reliable predictor for thrust moment in both models. The optimal (Cp, TSR) values for Pinwheel and Savonius turbines were (2.37, 0.223) and (0.63, 0.16) respectively, within an acceptable error range for experimental validation.

For this research, a comparative evaluation was performed in which the addition of 3D-printed biocarriers fabricated with 13X and Halloysite (13Χ-Η) and commercial Kaldnes K1 biocarriers were evaluated as opposed to the non addition of biocarriers in a semi-pilot scale MBBR-MBR unit. For the evaluation of the MBBR-MBR efficiency, various physicochemical parameters were measured while static light scattering and optical microscopy observations were additionally used. Biofilm extracted from the biocarriers was also evaluated. It was observed that in the MBBR-MBR K1 unit, the membrane filtration improved while in the MBBR-MBR 13X-H unit the membrane fouling rate was the same as in the control MBBR-MBR unit. This is due to the production of large amount of SMP which resulted from the large amount of biofilm created in the 13X-H biocarriers. An optimal biodegradation of the organic load was concluded for all three MBBR-MBR units. The nitrification and denitrification processes were improved at the MBBR-MBR units using 13X-H and K1. The dry mass produced on the 13X-H biocarriers was three orders of magnitude larger than that produced on the K1. Finally, it was observed that mostly EPS was produced in the biofilm of K1 biocarriers while in the biofilm of 13X-H mostly SMP.

Several studies show that air pollution has become a major problem and a source of great concern. Part of the observed poor air quality can be attributed to the levels of ultrafine particles (UFP), generally defined as the fraction of particles with diameter less than 100 nm which, by their size, are able to enter the blood circulation causing adverse health effects. As the main route of entry into the body is inhalation, several epidemiological studies associate the presence of UFP to total mortality, cardiovascular and respiratory problems. Since there are apparently no worldwide normative references for the control of these particles, this global study aimed to characterise the methods and techniques used worldwide regarding the monitoring and management of UFP. For this purpose, a survey was carried out based on a questionnaire applied at global scale. The questionnaire design was based on a preliminary literature review on the main search engines for scientific publications to establish the state of the art. As a result of the application of the questionnaire, a total of 51 responses were obtained from 20 different countries on five continents, which provided an insight into the global profile of professionals interested in the control/study of UFP, the measurement methodologies they follow and the guideline values they apply, if any. Among them are public health professionals, academics and health engineers from various institutions, such as education, hospitals, research centers and regulators in the health sector. Most responses said are no specific methodologies for the measurement of UFP, nor national standards for it. Through the results obtained in this study, it can be concluded that it is urgent to adopt regulations to standardize the assessments as well as to establish guide values for the protection of the human health.

Biogas production from organic waste is a promising renewable energy source, but achieving optimal production and digester stability can be challenging. This study investigated the impact of the Evogen microbial additive on biogas production and digester quality through microbial abundance and physicochemical parameter analysis. Two biogas plants, BG01 and BG02, were examined using 16S rRNA profiling to assess microbial abundance. Simultaneously, physicochemical parameters, including FOS/TAC ratio, total solids, volatile solids, biogas production, and VFA profile, were measured to evaluate digester performance. Results revealed distinct microbial community shifts in Evogen-treated digesters. Increased abundance of methanogenic archaea and hydrolytic bacteria indicated improved anaerobic digestion. Evogen supplementation also positively affected digester performance, with higher FOS/TAC ratios indicating enhanced acidification and methanogenesis. Reductions in total solids and volatile solids demonstrated improved organic matter degradation. Significantly higher biogas production was observed in Evogen-treated digesters, highlighting its potential as a microbial additive. Furthermore, VFA profiling demonstrated improved process stability and reduced substrate inhibition in Evogen-treated digesters. In summary, Evogen microbial additive positively influenced microbial dynamics, improving biogas production and digester quality. These findings contribute to optimizing biogas production systems and understanding the complex microbial interactions within anaerobic digesters.

Cathodic protection is widely used to protect metal structures from corrosion and is commonly applied on marine structures in seaports using sacrificial galvanic anodes. These anodes, either in Zinc, or preferen-tially nowadays in Al-Zn-In alloys, are expected to corrode instead of the metal to be protected. This leads to the release of specific dissolved species, Zn2+, Al3+, In3+ and solid phases like Al(OH)3. Few studies were conducted on the effects of anodes on marine organisms and concluded that further detailed investiga-tions are needed in controlled environments. We therefore propose an experimental approach to evaluate the effects of Zn and Al-Zn-In anodes on oysters stabulated in tanks, under conditions approaching those used in the ports. We chose a non-targeted metabolomic approach, using UHPLC coupled to HRMS, to study the effects on the entire metabolome, without any a priori. A modelling study of the chemical species, corresponding to the deg-radation products of the anodes, likely to be present near the exposed oysters, was also included. We identified 16 and 2 metabolites modulated by Zn- and Al-Zn-In-anodes respectively, involved in bi-ological functions, such as energy metabolism, osmoregulation, oxidative stress, lipid, nucleotide nucle-oside and amino acid metabolisms, defense and signaling pathways.

Anaerobic digestion has emerged as an increasingly popular method for the effective management of organic waste and wastewater with the potential to generate renewable energy. However, efficient digestion depends heavily on the complex and diverse microbial communities mediating this process. This review paper delves into the complex microbiome that exists within anaerobic digestion digesters, playing a critical role in the efficient and sustainable conversion of organic waste into biogas. Its primary focus falls within the scope of how various operational and environmental factors, including temperature, pH, hydraulic retention time, substrate loading rates, and the presence of inhibitory compounds, can substantially impact the microbiome of these systems. Through an extensive analysis of the existing literature, the microbial ecology of anaerobic digestion, including the composition and function of the microbial community, their interactions, and responses to different stressors, are evaluated. By offering critical insights into the distribution patterns of active microbial populations upon alterations in various process parameters, a better understanding of the microbial dynamics within these systems is provided, enhancing their efficiency. Overall, this paper emphasizes the importance of unraveling the microbial evolution within AD reactors to optimize biogas production and sustainable waste management and proposes future perspectives in this direction.

This research experiments with a sustainability assessment based on the Sustainable Development Goals (SDGs) of Agenda 2030 through a process of their territorialisation and implementation. This process enables the development of a Spatial Decision Support System (SDSS) that can be integrated with strategic environmental assessments in urban planning. The assessment takes place on the transversality of the sustainability concept by trying to consider together the three dimensions (environmental, social and economic) into a single assessment through the Spatial Sustainability Assessment Model (SSAM) by integrating Geographic Information Systems (GIS) and multi-criteria analyses. Economic development, social equity, and ecological integrity represent three common visions for rethinking peri-urban edges.

This paper addresses the issue of the automatic identification of river reaches and their planform type, given the (observed) set of geomorphic elements and units. It introduces further advances with respect to the original proposal by Nardini and Brierley. And it explores explicitly the ability of the algorithm and associated tools to work properly on significantly different rivers while adopting a given same parametrization. This was indeed an envisaged ability speculated as a challenging conclusion of the previous work. The Duqueco, Laja and Biobío rivers (Chile) are analyzed for this purpose. The conclusion is definitely positive, what opens future promising application horizons.

Abstract. Natural Thermoluminescence (TL) from the core of MD81349 marine calcareous biological ooze samples in the ninetyeast ridge of the equatorial northeast Indian Ocean and samples from the core of IODP306-U1312B in the high latitudes of the North Atlantic Ocean was studied. The spurious TL intensity of 395 °C peak is dose independent when the heating rate is 6 °C/s in a nitrogen atmosphere . TL signals exhibit a significant correlation on the marine isotope stages (MIS) at the two oceans since the mid-Pleistocene. High TL intensity corresponds to a negative δ18O in the interglacial stages, and low TL intensity corresponds to a positive δ18O in the glacial stages. TL of both cores at the two oceans reveal that the global climate has experienced eight cold and warm cycles since the mid-Pleistocene. Single-frequency spectrum analysis of MD81349 and U1312 TL in the last 300 ka was performed.Near the equator of the Northeast Indian Ocean，it is more significant that the short cycle of 38 ka and 5 ka while it is more significant that the cycle of 8 ka at the North Atlantic.In addition, correlation analysis shows that the TL has a significant positive correlation with trace elements 135Ba, a significant negative correlation with 47Ti. The impurity ions (e.g. Ba2+, Mn2+ and Ti2+) doped in carbonate are acting as activators and suppressants respectively.Time series of the TL of calcareous biological ooze tests provide an important record of climate change. The source of TL signal is also discussed.

The travel-goods industry is an essential part of the larger travel and tourism sector, but it creates significant environmental impacts due to resource and energy consumption. This study investigates the feasibility and sustainability potential of servitisation concepts within the travel-goods industry, and the Product-Service System (PSS) models, in particular, to identify steps towards a more sus-tainable travel industry in the future. It explores the sustainability-related drivers within the luggage industry and identifies barriers to the adoption of servitisation models, and opportunities for value creation for both consumers and commercial organisations. Business models are mapped into a ty-pology to highlight different pathways to PSS adoption, underpinned with empirical data collected via a consumer sentiment survey and semi-structured interviews with industry experts. Even though the analysis revealed shifting consumer attitudes towards servitisation concepts within the travel-goods market, with a significant level of interest emerging for specific PSS models, at present, the widespread adoption of PSS is hindered. This is due to the fragmented nature of global supply chains and entrenched ownership values. Addressing supply chain issues regarding end-of-life systems to sustainably manage products beyond functional obsolescence is critical. In parallel, product-oriented PSS models are more likely to increase, driven by a burgeoning resale market and supported by digi-tal technologies, which in turn can lead to greater prospects for use-oriented PSS adoption and even-tually, reduced environmental impacts.

In this study, UAV (Unmanned Aerial Vehicle) photogrammetry was used to monitor the ground displacement on the slope below a coal waste-rock stockyard, and to investigate the role of rainfall on this displacement. The study area is a mountainous region in Korea, where coal mining continues, and coal waste-rock is stored on the slopes of the mountain. In this area, ma-terial removal work was undertaken to reduce the steepness of the slope and driving forces in order to prevent disasters, but the strategy requires continuous monitoring to confirm the stabilization of the slope. For slope monitoring, a total of six UAV photogrammetry campaigns were conducted between April 2019 and August 2020. As a result of data processing, an orthoimage and DSM (Digital Surface Model) were generated. The ground displacement was estimated through four ways: slope extraction, displacement area evaluation, horizontal displacement, and vertical displacement analysis. During the study period, the maximum vertical displacement was 3.3 m and the maxi-mum horizontal displacement was 3.5 m. The horizontal displacement was effectively evaluated through the measurement of the movement of the drainage system using orthoimages that captured with a periodic survey. The effects of rainfall on ground displacement were also investigated. A very clear linear relationship between rainfall intensity higher than 20mm/d and ground displacement was identified. Accumulated amount of rainfall also showed good correlation with slope movement, but the frequency of rainfall intensity below 20 mm/d showed relatively low correlation with ground dis-placements.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

In this study, we present a statistical forecasting framework and assess its efficacy using a range of established machine learning algorithms for predicting Particulate Matter (PM) concentrations in the Arctic, specifically in Pallas (FI), Reykjavik (IS), and Tromso (NO). Our framework leverages historical ground measures and 24-hour predictions from 9 models provided by the Copernicus Atmosphere Monitoring Service (CAMS) to provide PM predictions for the following 24 hours. Furthermore, we compare the performance of various memory cells based on artificial neural networks (ANN), including recurrent neural networks (RNNs), gated recurrent units (GRUs), long short-term memory networks (LSTMs), echo state networks (ESNs), and windowed multi-layer perceptrons (MLPs), which are commonly employed in time series forecasting tasks. Irrespective of the chosen memory cell type, our results demonstrate that the proposed framework consistently outperforms the CAM models in terms of mean squared error (MSE), with average improvements ranging from 25% to 40%. Additionally, we investigate the impact of outliers on the overall model performance.

Raw rubber production is the sole foundation for the rubber product industry, rendering raw rubber to manufacture essential commodities to mankind such as tires, condoms, surgical gloves, and so forth. Raw rubber production involves various stakeholders; however, literature focusing on the social impacts of raw rubber production and its supply chain has hereto been limited. Social life cycle assessment, a popular tool to assess the social impacts of a product or process and was deployed herein to assess the social profiles of three Sri Lankan raw rubber supply chains (crepe rubber, concentrated latex, and ribbed smoked sheets). The Social Hotspots Database v4 on Sima Pro v9.3 was used for the analysis. Results indicated that Governance and Labour rights & decent work had been affected in its supply chain of fertilizers due to Corruption and Freedom of association & collective bargaining issues, mainly in Belarus, and China. Proposed improvement options to address these touchpoints were found to be effective. For instance, if the importation of K-fertilizer shifted into low risk countries, overall social risks associated with Corruption and Freedom of association & collective bargaining in the supply chains could be reduced by ca. 36% and 25%, respectively. As a result, social risks in the aforesaid impact categories, i.e., Governance and Labor rights & decent work, were reduced by ca. 35-41% and ca. 17-20%, respectively. Such improvements may help positioning the Sri Lankan rubber industry in the sustainability-conscious-world rubber market. Further, the methodical hierarchy developed herein is suggested to adopt in any industry to measure social sustainability subjected to the relevant refinements to the supply chains.

In the present work, a comparative evaluation of an MBBR unit performance was carried out for the following cases: when adding 3D-printed biocarriers fabricated with 13X and bentonite, when using K1 commercial biocarriers and when not adding biocarriers at all. For the evaluation of the MBBR efficiency, various physicochemical parameters were measured, while static light scattering and optical microscopy observations were additionally used. Finally, biofilm extracted from the biocarriers was evaluated. The findings suggest that there is an optimal biodegradation of the organic load in all MBBR units. The nitrification and denitrification process were improved at the 3D MBBR as compared to the control MBBR and MBBR K1. The dry mass of the biofilm in the 3D-printed biocarriers was two orders of magnitude larger than the one in the K1 biocarriers. What is more, in the K1 biocarriers the mass of the biofilm varied in relation to time, due to the fact that it could not be kept inside the holes, something that was not observed to happen with the 3D-printed biocarriers. Finally, it was observed, mostly in the 3D MBBR and less in the K1 MBBR, that the growth of nitrifying bacteria and heterotrophs inside the units increased the biomass production in the form of SMP, which in turn favored the adhesion of biomass on the surface of biocarriers.

Freezing/thawing indices are important indicators of dynamics of frozen ground on the Qinghai-Tibet Plateau (QTP), especially for areas with limited observations. Based on the numerical outputs of Community Land Surface Model version 4.5 (CLM4.5) from 1961 to 2010, this study compared the spatial and temporal variations between air freezing/thawing indices (2 m above the ground) and ground surface freezing/thawing indices in permafrost and seasonally frozen ground (SFG) across the QTP, after presenting changes of frozen ground distribution in each decade in the context of warming and wetting. The results indicate that an area of 0.60×106 km2 permafrost of QTP degraded to SFG in 1960s-2000s, and the primary shrinkage period occurred in 2000s. The air freezing index (AFI) and ground freezing index (GFI) decreased dramatically at the rates of 71.00℃·d/decade and 34.33℃·d/decade from 1961 to 2010, respectively. In contrast, the air thawing index (ATI) and ground thawing index (GTI) increased strikingly with the values of 48.13℃·d/decade and 40.37℃·d/decade in the past five decades. Permafrost showed more pronounced changes in freezing/thawing indices since 1990s compared to SFG. The changes of thermal regimes in frozen ground shows closely relations to air warming until the late 1990s, especially in 1998 when the QTP has undergone the most progressively warming. However, a sharp increase in the annual precipitation from 1998 seems to take a stronger control role on thermal degradation in frozen ground than the air warming in 2000s. Meanwhile, the prominent vegetation expansion further promotes thermally unstable of frozen ground in this highly wetting period.

This study evaluates the agricultural carbon emission efficiency of Shandong Province from 2011 to 2020 using the DEA-SBM model. The nexus between endogenous and exogenous variables is estimated using the Tobit model. The findings reveal an overall increasing trend in agricultural carbon emissions, with significant variations in efficiency values among different cities, leading to a severe polarization. Spatial evaluation shows a high distribution trend in the central region and low in the eastern and western regions of Shandong Province. The empirical tests conducted for Shandong Province and its three regions indicate that urbanization plays a major role in sup-porting the growth of agricultural carbon emission efficiency, while the education level of the la-bor force has a suppressive impact. Economic development and crop cultivation structure, how-ever, have no significant influence. The impact of these variables varies across the eastern, central, and western regions. The proposed countermeasures include improving planting structure and reducing brain drain in the eastern region, strengthening agricultural and rural inputs and in-creasing the added value of agricultural products in the central region, and intensifying the link-age between urbanization and industrial layout in the western region to reduce agricultural car-bon emissions efficiency in Shandong Province.

The extensive use of carrier-aided smoothing code (CSC) filter has led to reduce the noise level of raw code measurements in GNSS positioning and navigation applications. However, the existing CSC technique is sensitive to the changes of the integer ambiguity and then the smoothing proce-dure needs to be restarted in the presence of cycle-slips. As the Doppler shift is instantaneous ob-servation and immune to cycle-slips, Doppler-aided smoothing code (DSC) algorithm would be more promising in challenged environment. Based on the Hatch-filter, an optimal DSC approach is proposed with the principle of minimum variance. Meanwhile, to inhibit the effect of integral cumulative error of Doppler, a balance factor is adopted to adjust the contributions of raw code and DSC. The noise level of code observable is not only affected by thermal noise, but also limited by systematic bias. Satellite code bias (SCB) has been identified in the raw code observable on each frequency for each BDS-2 satellite. By minimizing the sum of absolute value of residuals, polyno-mial segment fitting algorithm as a function of elevation-angles is applied to establish the SCB cor-rection model based on epoch-differenced Multipath (MP) deviations. Finally, numerical experi-ments demonstrate the validity and efficiency of the refined DSC filter with SCB corrections on each available frequency for BDS-2 un-GEO satellites.

Coastal areas situated at lower elevations are becoming more vulnerable to flooding as a result of the accelerating global sea level rise. As the sea level rises, so does the groundwater. Barriers designed to shield against marine flooding do not provide protection against flooding caused by rising groundwater. Despite the increasing threat of groundwater flooding, there is limited knowledge about the relationship between sea level rise and groundwater fluctuations. This hinders the ability to adequately consider sea level rise induced groundwater flooding in adaptation initiatives. This study aims to investigate how local groundwater in Juelsminde, Denmark, responds to changes in sea level and to evaluate the predictability of these changes using a machine learning model. The influence of the sea on the shallow groundwater level has been investigated using six groundwater loggers located between 45 and 210 m from the coast. An initial manual analysis of the data revealed a systematic delay in the rise of water levels from the coast to inland areas, with a delay of approximately 15–17 hours per 50 m of distance. Subsequently, a support vector regression model was used to predict groundwater levels 24 hours into the future. This study shows how the groundwater level in Juelsminde is affected by sea level fluctuations. Results suggest a need for increased emphasis on this topic.

Climate change affects both human and natural systems. Afghanistan ranked globally on the top of highly vulnerable countries to the adverse effects of climate change. The agricultural communities of Afghanistan is highly affected by climate change. Understanding farmers’ real experiences on changing climate become crucial in planning the future adaptation strategies. This study assessed the farmers' perception of climate change and its impacts on farming communities. Primary data were collected through face-to-face interviews conducted with 120 household heads. Additional qualitative data were collected by conducting 4 Focus Group Discussions (FGDs), 4 Historical Timeline Calendars (HTCs), 18 Key Informant Interviews (KII), and sketches of 4 Crop Calendars. The study reveals that climate indicators have varied and changed. The farmers express their experiences of decreasing snowfall in winter and annual rainfall in spring and summer, which led to the intensity and frequency of drought and water shortages for agriculture and rangelands in the upper and lower part of the valleys. The temperatures in winter and summer have increased and led to earlier snow melting, earlier blooming, flowering, and greening of the plants. These changes affected both positively and negatively. There is a half-month new opportunity for cultivation and increased earlier animal ranching in the rangelands. These findings can be valuable inputs for developing effective and efficient adaptation strategies.

: Submerged aquatic vegetation (SAV) are highly efficient at carbon sequestration and, despite their relatively small distribution globally, are recognized as a potentially valuable component of climate change mitigation. However, SAV mapping in tidal marshes presents a challenge due to optically complex constituents in the water. The emergence and advancement of deep learn-ing-based techniques in the field of habitat mapping with remote sensing imagery provides an opportunity to address this challenge. In this study, an analytical framework was developed to quantify the carbon sequestration of SAV habitats in the Atchafalaya River Delta Estuary from field and remote sensing observations using deep convolutional neural network (DCNN) tech-niques. A U-Net based model, Wetland-SAV Network, was trained to identify SAV percent cover (high, medium, and low) as well as other estuarine habitat types from Landsat 8/9-OLI data. The areal extent of SAV was up to 8% of the total area (47,000 ha) with a significant loss of SAV habitats observed post-Hurricane Barry (~2,300 ha) in 2019. The habitat areas and habitat-specific carbon fluxes were then used to quantify net greenhouse gas (GHG) flux of the study area for with/without SAV scenarios in a Carbon Balance Model. The total net GHG flux was in the range of -0.13 ± 0.06 to -0.86 ± 0.37 ×105 tonne CO2e yr-1 and increased up to 40% (-0.23 ± 0.10 to -0.90 ± 0.39 ×105 tonne CO2e yr-1 ) when SAV was accounted for within the calculation. At the hectare scale, inclusion of SAV resulted in an increase of ~60% for net GHG sink in shallow areas adjacent to emergent marsh where SAV was abundant. This is the first attempt at remotely mapping SAV in coastal Louisiana as well as a first quantification of net GHG flux at the scale of hectares to thousands of hectares, accounting for SAV within these sub-tropical coastal delta marshes. Remote sensing and deep learning models have high potential for mapping and monitoring of SAV in turbid sub-tropical coastal deltas as a component of increasing accuracy of net GHG flux estimates at small (hectare) and large (coastal basin) scales.

Organic wastes and by-products from several activities, including food industries, farming, and animal husbandry, are a hygiene threat when aerobically decomposed. Therefore, their manage-ment is crucial for public health. In this direction, anaerobic digestion (AD) systems may be the solution by transforming waste into energy, which may decrease the environmental impact. However, their efficacy should be carefully examined. In this innovative study, we evaluated the physicochemical and microbial characteristics of liquid digestate (LD) retrieved from organic animal wastes in northern Greece using nanofiltration. Using treatment technologies including physical (solid-liquid separation, microfiltration and nanofiltration) and biological (anaerobic digestion), heavy metals and microbial (i.e., Salmonella spp., Escherichia coli, Enterococcus faecalis) concentrations reduced and nutrients were recovered. This work sets the basis for the efficient management of liquid digestate. Our method may enable the use of treated liquid digestate for unlimited irrigation water and other industrial applications of water. Apart from the sanitation process, the recovery of nutrients for soil fertilization seems to be a more sustainable way for fu-ture agricultural practices.

Abstract: The need to rapidly reduce GHG has accelerated the adoption of circular models of production. However, this has proved to be a challenging task for SMEs, who lack the financial, organizational and informational capabilities to implement circular business models. In this context, calculating the carbon footprint (CF) of their products could provide the basis for assessing the different circular economy (CE) practices. The aim of this study is to present a CF calculation tool that can be used to calculate the CF of SMEs. The design of the tool was based on the Life Cycle Assessment (LCA) methodology, taking into account the various barriers that SMEs face in adopting CE practices. The tool was tested in a small cheese factory in northern Greece. The pro-duction process was mapped, a GHG inventory was created and the total emissions related to the production of a specific product was estimated. The final aim is to test this tool at a large scale.

Introduction. Environmental Health in a Global World at New York University was re-designed as a class participatory effort, challenging undergraduate students to understand environmental hazards and the resultant adverse health outcomes by embracing the inherent complexity of environmental risks and proposing solutions. Methods. Following introductory lectures, students are placed into teams and assigned a specific perspective, or avatar, which includes learning to see the challenge from the perspective of a technical expert such as a biologist, an engineer, or an anthropologist. The teams then design specific systems maps to visualize the complex interactions that lead to adverse health outcomes after a given environmental exposure. The maps highlight potential leverage points, where relatively minor interventions can provide a disproportionate benefit in health outcomes. The teams then explore potential interventions and identify the potential unintended consequences of those actions, develop and advocate for innovative new strategies to mitigate risk and improve outcomes. Results and Discussion. Over the past 5 years we have taught this methodology to over 680 students with strong, student-oriented results. The teams created and presented more than 100 strategies, addressing a diverse set of environmental challenges that include water contamination, gun violence, air pollution, environmental justice, health security, and climate change. Developing the strategies helped the students understand environmental threats in a more holistic way, provided them with some agency in finding solutions, and offered an opportunity for them to improve their presentation skills. The responses in course evaluations have been enthusiastic, with many students reporting a deep impact on their college experience.

Sharing facilities with other households offers the most realistic opportunity for access to sanitation to many households in low-income settings. However, questions remain about the safety of shared toilets, including those shared at the household level. This study sought to compare the usage and microbial safety of household-level shared and unshared toilets in a Ghanaian rural district to investigate any association between their microbial safety and sharing status. A semi-structured questionnaire was used to collect data on the user characteristics of the sampled toilets, while common contact surfaces (door handles and toilet seats) were assessed for faecal contamination following standard swab sampling and analytical protocols. The results of the study indicate that sharing toilets affords about 90% more household-level access to sanitation as compared to single-household toilets. Toilet sharing mostly occurred between two households, with a maximum user population of 14 per toilet. Generally, there was a high prevalence of faecal contamination of the door handles and seats of both shared and unshared toilets, but this had no association with the sharing status of the toilets. The median concentration of E. coli on door handles and seats of shared toilets were 34.3 x 105 and 103.2 x 105 CFU/ml respectively as compared to 54.7 x 105 and 125.0 x 105 CFU/ml respectively on unshared toilets. In conclusion, the sharing of toilets at the household level nearly doubles access to sanitation at home without necessarily exposing the users to a higher risk of faecal-oral disease transmission.

Habitat quality has great significance for regional ecological conservation and human welfare. In this study, we evaluated the spatial and temporal characteristics of land use and habitat quality in the temperate desert sub-region of Ordos Plateau using patch-generating land use simulation (PLUS) and integrated valuation of ecosystem services and trade-offs (InVEST) models. From 2000 to 2020, the areas of grassland, cropland, and unused land in the study area increased significantly; the areas of water bodies and woodland increased slightly; and the area of wasteland decreased significantly. Moreover, the habitat quality in the temperate desert subzone of the Ordos Plateau showed a trend of increasing and then decreasing from 2000 to 2020. The areas of lower and low habitat quality first decreased and then increased, and the overall area decreased over time. Conversely, the areas of high and higher habitat quality initially increased and then decreased, and the overall area increased over time. The area of medium habitat quality first decreased and then increased, although the overall change was minimal. Based on the PLUS model, the habitat quality of the study area in 2025 predicted under the natural development scenario was compared with that predicted under the ecological conservation scenario, showing higher habitat quality and lower habitat degradation under the ecological conservation development scenario. These results can be used to provide a scientific basis and decision reference for the sustainable use of land resources and high-quality socio-economic development in the temperate desert sub-region of the Ordos Plateau.

The Süttő 21 site is a fissure fill of the freshwater limestone of the Gazda quarry in Süttő. The material was collected between 2017 and 2019, the results are summarised in this article, with a special focus on the small vertebrate fauna of the site and its stratigraphic and paleoecological significance. The fissure fill can be placed around the early/middle Pleistocene boundary (ca. 1.1 and 0.77 Ma). The paleoecological analysis of the herpeto- and mammal fauna of the sequence indicates the proximity of a permanent water body. The lower part of the sequence is dominated by open habitat indicator taxa indicating a cool, dry climate. Towards the upper part of the sequence, the climate remained cool but became wetter, and the vegetation gradually changed to forest-steppe/open forest. The fauna of the Süttő 21 site can be compared with the material of sites, which are of similar age, thus revealing taxonomic and paleoecological differences between different areas of the country. While a warm, dry climate and open vegetation can be reconstructed in the Villány Hills around the early/middle Pleistocene boundary, the northern Hungarian areas had a cooler, wetter climate, and slightly more closed (grove, forest-steppe) vegetation during this period.

Additives can improve the efficiency of anaerobic digestion by increasing biogas production, reducing air pollution, and preventing total ammoniacal nitrogen (TAN) inhibition. Biological or chemical supplementation can also improve the economic efficiency of anaerobic digestion. However, the effects of specific additives on biogas production can vary depending on the type of supplement used. This research utilizes the additives on an industrial scale and monitors the optimization of the anaerobic digestion operating parameters after their addition. The various AD additives were examined in a sufficient cycle of operation for three biogas plants located in northern Greece. In this manner, the effectiveness was investigated in multiple initial feeds and unstable operating situations caused by the seasonality of specific feedstocks. The existing operation state in the three biogas plants was recorded before and after adding the supplements. In all three cases, lower concentration levels were observed in many of the examined trace elements. Introducing additives proved to be a stabilization factor in AD performance and inhibition mediator.

Several methods of processing wood into strong, durable products for the construction industry provide transformative opportunities to substitute for less sustainable building materials. Carbon storage is a further advantage, with the added possibility of combustion for bioenergy at end of life. Intense research activity in this area is expected to open up new markets for wood fiber during the lifetime of trees now being planted. Here, wood-derived materials are classified according to the particle size, from metres to nanometres, into which the wood is fragmented before reconstitution. Materials made by densifying or chemically modifying solid wood with no fragmentation are already in production for exterior doors, window frames and cladding, with improved uniformity and stability compared with unmodified wood. Pre-commercial developments promise further gains in durability and strength. Emerging developments extend these process technologies to wood that has been chipped or stranded or pulped, retaining the above advantages over raw timber for weather-facing applications and adding processability by moulding or extrusion. Crucially, the raw material does not then need to be sawn timber but can be bioenergy-grade wood biomass. This will facilitate afforestation strategies that combine the aims of carbon sequestration and biodiversity.

Communities in semi-arid lands use sand dams to enhance access water during the dry seasons. However, there is limited information on the quality of water derived from these sand dams, especially in degraded lands where storm surface runoff poses contamination risk. Thus, this study aimed at assessing the spatial-temporal variations in water quality of sand dams in Chepareria, West Pokot County in Kenya. Water samples were collected from scooping holes across18 purposefully selected sand dams. Results obtained showed significant differences in water quality based on sand-dams age and location of scooping holes, but the magnitude of these differences differed with specific properties. For instance, in recently constructed sand dams (< 1 year), scooping holes near the sand dam wall had lower pH values (8.5) than holes scooped a distance from the sand dam wall (9.2). For total dissolved solutes and microbial properties, sand dam age had the greatest impact than the location of scooping holes. For example, water obtained from < 1 year old sand dams had significantly higher TDS with an average value of 100.3 mg L-1. The thermotolerant coliforms (TTC) exceeded the maximum allowable levels recommended by World Health Organization. Thus, water obtained from these sand dams should be treated before consumption. Finally, sand dams meant for domestic water harvesting should be protected. Shallow wells with appropriate aprons for effective protection against contamination should be installed to enhance abstraction of safe water from sand dams.

As in many parts of the world, rural-urban, forest-urban interface areas surrounding urban regions expose the natural areas they interact with to a threat of fire risk that can reach various sizes. This risk has been assessed for various regions of the world using many different methods and numerical models so far. Among these, it is seen that machine learning models have successful applications in risk assessment and risk prediction studies. For the fire risk prediction of Istanbul's yet unurbanized regions, but where the city is anticipated to potentially shift, data was collected using the opportunities provided by Geographic Information Systems and Remote Sensing technologies based on fires that occurred between 2000-2021, and the region was examined. Machine learning methods' Random Forest (RF), Extreme Gradient Boosting (XGB), and Light Gradient Boosting (LGB) models were applied for the classification of factors effective in fire. The best result was given by the RF model with 0.93 accuracy, 0.062 F1 score, and 0.753 Area Under Curve (AUC) value. In the classification of factors in the RF model, the grouping between fire-initiating factors and factors effective in spreading is evident, while this distinction is partially noticeable in the other two models.

The determination and classification of seafloor sediment types are crucial for the exploitation of marine resources, construction of marine engineering, and maintenance of marine ecological en-vironments. Automatic classification of seafloor sediment based on acoustic telemetry data is an important method to quickly understand the type of a large range of sediment. Currently, most studies on sediment classification are based on multi-beam backscattering intensity data, which is a relatively single data type. Besides, the low-dimensional details of standard U-Net gradually weaken in the propagation process, limiting the accuracy of sediment classification. Therefore, this study proposes an automatic classification method of seafloor sediment types based on an im-proved U-Net and K-means clustering algorithm, using multi-beam water depth, sub-bottom profile, and sample test data in the Northern Slope of the South China Sea. Six sediment types, including gravelly muddy sand, sand, silty sand, less muddy silt, muddy silt, and silty mud, were identified in the study area. Additionally, the study area was divided into four sedimentary en-vironment zones, including the shelf sedimentary area, the upper shelf slope break sedimentary area, the lower shelf slope break mixed sedimentary area, and the slope deposition area, based on the results of sediment classification and geological background. The sedimentary environment zones were found to be distributed along the trend of the shelf slope break line. The results of this study not only provide an important supplement to the existing classification methods of seafloor sediments but also contribute to the understanding of the sedimentary environment and process of the Northern Slope of the South China Sea.

Converting biowaste into biochar and subsequently putting it into the soil are considered to be an effective approach to sequestrate carbon (C). However, biochar will inevitably undergo the aging process in soil, which influences its stability, and ultimately threatens its carbon sequestration ability. This study selected CaCl2 as exogenous additive of sewage sludge and bone dreg to quantify both surface C and bulk C stability in Ca-rich biochars under three aging processes (dry-wet aging, freeze-thaw aging, and natural aging in farmland soil), and revealed the influence mechanisms of exogenous Ca on biochar stability. Results showed that after dry-wet aging (25 rounds), freeze-thaw aging (25 rounds), and natural aging in different farmland soils (5 months), oxidized surface C in Ca-rich biochar decreased by 10~23%, 28~41%, and 0~74%, respectively, compared to that in pristine biochar, while oxidized bulk C decreased by 6~10%, 0~1%, and 0~35%, respectively. Under three aging processes, the surface C and bulk C stability in Ca-rich biochar were superior to that in corresponding pristine biochar, which was attributed to the “protective effect” of Ca-containing crystals on biochar surface, including CaO, Ca5(PO4)3Cl, Ca5(PO4)3(OH), Ca8H2(PO4)6·H2O and Ca10(PO4)6(OH)2. These Ca-containing crystals could block the connection between biochar-C and the external oxidizing environment, intervening the oxidation of C-C/C=C in biochar, but also prevented aging from damaging C structure of biochar, reducing the generation of fragmented structure. By comprehensively assessing surface C and bulk C stability under three aging processes, final C sequestration in Ca-rich biochar increased to 27~80%, compared to that in pristine biochar (23~74%). Therefore, Ca-rich biochar is more dominant than pristine biochar, considering C sequestration potential during long-term aging in soil.

The physiological characteristics of liquid digestate retrieved from various biogas plants based in northern Greece are presented. Preliminary photocatalysis experiments on inoculated liquid di-gestate sampled showed that disinfection is possible when pre-treated digestate with a combination of centrifuge-flocculation-μFiltration after 5.5 hours of 0.7g/L suspended TiO2 under UVA illumination for the experimental conditions is used. A novel design photocatalytic nanofiltration reactor was implemented for disinfection experiments on pre-treated liquid digestate, giving promising results. This work sets the basis for the efficient operation and engineering application of technology collaboration with photocatalysis as the final step for liquid digestate sanitation and reusable water recovery.

This study addresses the limited coverage of regulatory monitoring for particulate matter 2.5 microns or less in diameter (PM2.5) in Thailand due to the lack of ground station data by developing a model to estimate daily PM2.5 concentrations in small regions of Thailand using satellite data at a 1-kilometer resolution. The study employs multiple linear regression and three machine learning models and finds that the random forest model performs the best for PM2.5 estimation over the period of 2011-2020. The model incorporates several factors such as Aerosol Optical Depth (AOD), Land Surface Temperature (LST), Normalized Difference Vegetation Index (NDVI), Elevation (EV), Week of the year (WOY), and year and applies them to the entire region of Thailand without relying on monitoring station data. Model performance is evaluated using the coefficient of determination (R2) and root mean square error (RMSE), and the results indicate high accuracy for training (R2: 0.95, RMSE: 5.58 μg/m3), validation (R2: 0.78, RMSE: 11.18 μg/m3), and testing (R2: 0.71, RMSE: 8.79 μg/m3) data. These PM2.5 data can be used to analyze the short- and long-term effects of PM2.5 on population health and inform government policy decisions and effective mitigation strategies.

Based on the ERA5 reanalysis dataset of the European Centre for Medium-Range Weather Forecasts (ECMWF), the climatology of the planetary boundary layer height (PBLH) in Jiangsu, China, is studied. The PBLH based on ERA5 is verified by using radiosonde data, and the results show that the PBLH based on ERA5 fits very well with the PBLH diagnosed by the radiosonde data. Overall, the daytime average PBLH is between 700-1200 m, which is higher in the north and lower in the south. It is between 100 and 400 m at night, and it is lower in the north and higher in the south. PBLH exhibits complex spatiotemporal variation. In the daytime, the PBLH in inland areas is highest in spring, followed by fall and summer, and lowest in winter. At night, the seasonal variation in the PBLH is less obvious. The seasonal variation in the PBLH in coastal areas is higher in fall and winter and lower in spring and summer. PBLH shows an obvious diurnal cycle, usually reaching its peak at 14:00 (LST) or 15:00 (LST). The diurnal cycle of the PBLH is significantly positively correlated with the near-surface temperature and wind speed and significantly negatively correlated with the relative humidity and lower tropospheric stability. The daytime PBLH increases significantly in most areas. The increase in PBLH can be attributed to the increase in near-surface temperature and the decrease in near-surface relative humidity and lower tropospheric stability.

In this paper, mesoporous electrodes consisted of Sb-doped SnO2 deposited onto Ti plates controlled corroded under acidic medium were synthesized by spin-coating method, and morpho structurally characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrodes were electrochemical testing in the degradation/mineralization by electrooxidation (EO) of doxorubicin (DOX) as single-component and multi-component together with capecitabine (CCB)-from cytostatic class and humic acid (HA)-from natural organic matter (NOM) class in the absence/the presence of activated carbon (AC) as particulate electrode. The best mineralization efficiency of 67 % was achieved for DOX mineralization using Sb-doped SnO2 deposited onto Ti plate controlled corroded with oxalic acid in electrooxidation process. The presence of AC within the electrolysis process generated a synergy effect of 52.75 % for TOC parameter removal, which is in accordance and quite better than the result reported in the literature. The aspects related to the complex mechanism of DOX degradation and mineralization are discussed. The superiority of AC assisted electrooxidation, as electrochemical filtering (EF), was proved considering simultaneous degradation and mineralization of mixture of doxorubicin, capecitabine and humic acid.

Comparison with conventional reservoirs, the prediction of pressure in ultra-deep tight sandstone formations is difficult. The prediction of seismic pressure is more challenging than well logging pressure prediction. The main methods for seismic pressure prediction include equivalent depth method, Eaton method, Fillippone formula, and its modified versions. Among them, the Eaton method is widely used and has good effectiveness. However, this method relies on difficult-to-obtain normal compaction trend line, which leads to low prediction accuracy in space. To address this issue, a method combining the Eaton method and Collocated cokriging is proposed. The Eaton formula is used to predict formation pressure at the well, with compressional wave velocity as the covariate for predicting the main variable, formation pressure. By simulating the shear wave velocity based on seismic compressional wave velocity, the influence of various parameters on the prediction results is analyzed, and the accuracy of this method is verified by comparing it with other methods. The proposed method is then applied to predict formation pressure in the ultra-deep formations of the Junggar Basin. The simulation results show that the Collocated cokriging method achieves higher planar accuracy and better matches the experimental expectations in terms of prediction results. The application results also demonstrate the scientific effectiveness of the combined method, which has achieved good results in practical production applications.

There are four commercial pathways to make grill charcoal from wood. These have been modelled to calculate a carbon intensity (CI) for each. Results are presented along with discussion of the sensitivities: biogenic carbon; quality of the charcoal; classification of products, wastes and residues; and division of burden. Grill charcoal’s CI ranges greatly, depending on the pathway by which it is produced. Wood distillation, a commercial process that once was common but now is rare, has a CI 50+% lower than that of the next-lowest commercial process, Kilns. Earth mounds/pits and external-fuelled Retorts have CIs considerably higher still. The carbon efficiency (CE) of Wood distillation is more than twice that of the next-best, again Kilns. CE is defined as normalised, total carbon emitted. This is not the same as CI, it is not usually considered in studies such as this, yet it is important for climate impact. CE could be a useful measure in assessments (such as this) where biogenic carbon is significant.

Tipping bucket rain gauges (TBRs) have been, and apparently will continue to be one of the most widely used pieces of equipment for rainfall monitoring, being frequently used for the calibration, validation and downscaling of radar and remote sensing data, due to their major advantages–low cost, simplicity, and low energy consumption. Thus, many works have focused and continue to focus on their main disadvantage–measurement biases (mainly in wind and mechanical underestimations). However, despite arduous scientific effort, calibration methodologies are not frequently implemented by monitoring networks operators or data users, propagating bias in databases and in the different applications of such data, causing uncertainty in the modeling, management, and forecasting in hydrological research, mainly due to a lack of knowledge. Within this context, this work presents a review of the scientific advances in TBR measurement uncertainties, calibration, and error reduction strategies from a hydrological point of view, by describing different rainfall monitoring techniques in Section 2, summarizing TBR measurement uncertainties in Section 3, focusing on calibration, and error reduction strategies in Section 4, a discussion and perspectives in Section 5, and conclusions in Section 6, providing an overview of the of the state of the art and future perspectives of the technology.

As one of the common techniques for measuring coseismic deformations, optical image correlation techniques are capable of overcoming the drawbacks of inadequate coherence and phase blurring which can occur in radar interferometry, as well as the problem of low spatial resolution in radar pixel offset tracking. However, the scales of the correlation window in optical image correlation techniques typically influence the results, the conventional SAR POT method faces a fundamental trade-off between the accuracy of matching and the preservation of details in the matching window size. This study regards co-seismic deformation as a two-dimensional vector, and develops a new post-processing workflow called VACI-OIC to reduce the dependence of shift estimation on the size of the matching window. This paper takes the coseismic deformations in both the east-west and north-south directions into account at the same time, treating them as vectors, while also considering the similarity of displacement between adjacent points on the surface. Herein, the angular continuity index of the coseismic deformation vector was proposed as a more reasonable constraint condition to fuse the deformation field results obtained by optical image correlation across different matching window. Taking the earthquake of 2021 in Maduo, China, as the study area, the deformation with the highest spatial resolution in the violent surface rupture area was determined (which could not be provided by SAR data). Compared to the results of single-scale optical correlation, the presented results were more uniform (i.e., more consistent with published results). At the same time, the proposed index also detected the strip fracture zone of the earthquake with impressive clarity.

Evaluating the performance of water indices and mapping the spatial distribution of water-related ecosystems are important for monitoring surface water resources. This is particularly the case for Ethiopia since there is limited information available on water resources development over time despite its relevance for the people and ecosystems. To address this problem, this paper evaluates the performance of seven water indices for country-scale surface water detection based on high spatial and multi-temporal resolution Sentinel-2 data, processed using the Google Earth Engine cloud computing system. Results show that the water index (WI) and automatic water extraction index with shadow (AWEIsh) are the most accurate ones to extract surface water. Comparisons are based on qualitative visual inspections and quantitative accuracy indicators. For the latter, WI and AWEIsh obtained kappa coefficients of 0.96 and 0.95, respectively, and an overall accuracy of 0.98 each. Both indices accounted for similar spatial coverages of surface waters with 82,650 km2 (WI) and 86,530 km2 (AWEIsh) for the whole of Ethiopia.

Using a database of 378 hail days between 20981 and 2020, the climatic characteristics of 23 convective parameters from sounding data and ERA5 data were statistically analyzed. The goal of this work is to evaluate the usefulness and representativeness of convective parameters derived from sounding data and reanalysis data for the operational forecast of the hail phenomenon. As a result, average values from 12:00 UTC were 433J / Kg for CAPE in the case of data from ERA5 and 505 J/kg from rawinsonde respectively. The Spearman correlation coefficients matrix between the values of the parameters indicates high correlations between the parameters calculated based on the parcel theory, the humidity indices, and the complex indices. The probability for large hail maximizes with high low level and boundary layer moisture, high CAPE, and a high lifted condensation level height.

Considering the differences between the European and African continents concerning the management of the mining production sector, we decided to carry out this study with the main objective of demonstrating that, in Africa, mining can positively change the quality of life of the populations where it develops and, at the same time, it is possible to respect the environment, which is our main wealth. To achieve these objectives, it is necessary to present the mining activity of the continent, emphasizing both the negative aspects and its strong points. The most important thing is to make a good diagnosis of the situation, which will allow us to cure our "patient", that is, African mining production.

The relocation of the Indonesian capital from Jakarta to Ibu Kota Nusantara (IKN) East Kalimantan IKN will affect several sectors. The change in land use from vegetated to developed land will lead to local climate changes, including the emergence of the urban heat island (UHI) phenomenon, which is reflected in a higher land surface temperature (LST) than the surrounding area. In this study, an analysis of UHI propagation was conducted on a seasonal (DJF, MAM, JJA, and SON), with 5 yearly periods from 2001 to 2020, study area in IKN and its buffer cities (Balikpapan, Samarinda, and Bontang). Terra-MODIS satellite data are processed using Google Earth Engine (GEE) platform and output is done using GrADS. UHI (high LST) is found in urban areas/buffer cities both spatially and temporally in every season, while UHI has not yet occurred in IKN (low LST) and suburban, rural, hilly areas, vegetated areas, and water bodies (lakes, rivers). The cross-sectional latitudinal and longitudinal analysis showed that the LST DJF2015-2020 from highest to lowest temperature are in Balikpapan City (36.84 OC), Samarinda City (36.13 OC), Bontang City (32.3 OC); and IKN zero point (28.82 OC). The UHI propagation was observed in 2001-2005, 2006-2010, 2011-2015, and most during 2016-2020. Seasonally, the UHI was most pronounced in the SON season, while on lowest UHI was observed in the MAM season.

High-precision ground point cloud data has a wide range of applications in various fields, and the separation of ground points from non-ground points is a crucial preprocessing step. Therefore, designing an efficient, accurate, and stable ground extraction algorithm is of great significance for improving the processing efficiency and analysis accuracy of point cloud data. The study area in this article was a Park in Guilin, Guangxi, China. The point cloud was obtained by utilizing the UAV platform. In order to improve the stability and accuracy of the Filter algorithm, this article proposed a triangular grid filter based on Slope Filter, found violation points by the spatial position relationship within each point in the triangulation network, improved KD-Tree-Based Euclidean Clustering, and applied it to the non-ground points extraction, this method has good accuracy, stability and achieves good results in separating ground points from non-ground points. At first, using Slope Filter to remove some non-ground points, to reduce the error of taking ground points as non-ground points; Secondly, established a triangular grid based on the triangular relationship between each point, the violation-triangle can determin through the grid, and then the corresponding violation points were found in the violation-triangle; Thirdly, according to the three-point collinear method to extract the regular points, used these points to extract the regular landmarks by KD-Tree-Based Euclidean Clustering and Convex Hull Algorithm; Finally, removed disperse points and irregular landmarks by Clustering Algorithm. In order to confirm the superiority of this algorithm, this article compared the filter effects of various algorithms on the study area and filtered the 15 sample data provided by ISPRS, and obtained an average error of 3. 46%. The results showed that the algorithm in this article have a high processing efficiency and accuracy, which can greatly improve the processing efficiency of point cloud data in practical applications.

The practical utility of remote sensing techniques relies on validating them with ground-truth data. Validation requires similar spatial-temporal scales for ground measurements and remote sensing resolution. Evapotranspiration (ET) estimates are commonly compared to weighing lysimeter data, which provide precise but localized measurements. To address this limitation, we propose using superconducting gravimeters (SG) to obtain ground-truth ET data at larger spatial scales. SG measure gravity acceleration with high resolution (tenths of nm/s2) within a few hundred meters. Similar to lysimeters, gravimeters provide direct estimates of water mass changes for determining ET without soil disturbance. To demonstrate the practical applicability of SG data, we conducted a case study in Buenos Aires Province, Argentina (-34.87, -58.14). We estimated cumulative ET values for 8-day and monthly intervals using gravity and precipitation data from the study site. Comparing these values with MODIS-based ET products (MOD16A2), we found a very good agreement at the monthly scale, with an RMSE of 32.6 mm/month (1.1 mm/day). This study represents progress in using SG for hydrogeological applications. The future development of lighter and smaller gravimeters is expected to further expand their use.

Thermal treatment in Australia is gaining interest due to legislative changes, waste reduction goals, and the need to address contaminants risks in biosolids used for agriculture. The resulting biochar product has the potential to be beneficially recycled as a soil amendment. On-farm management practices were reviewed to identify barriers that need to be overcome to increase recycling and examine the role of pyrolysis and gasification in effectively improving the quality and safety of biochar. Key findings revealed: (1) thermal treatment can effectively eliminate persistent organic pollutants, microplastics and pathogens, and (2) more than 90% of the total heavy metals content in biosolids become immobilized when these are converted to biochar, thus reducing their bioavailability following land application. While reported research on the short-term effects of biosolids-derived biochar suggested promising agronomic results, there is dearth of information on long-term effects. Other knowledge gaps include optimisation of land application rates, understanding of rate of breakdown and fate of contaminants in soil and water, heavy metal mobility in soil and bioaccumulation or transfer to the food chain. Improved understanding of nutrients and contaminants dynamics in soils receiving biosolids-derived biochar is a pre-requisite for their safe use in Australian agriculture, and therefore it is highlighted as priority area for future research.

Two monophyletic Daphnia species (Daphnia magna and D. similis) were exposed to a sub-lethal concentration of Pb (50 µg/L) for nine generations under two food regimes (usual and restricted) and analysed for acetylcholinesterase (AChE) activity, hatching delay and lifespan, and Net Reproductive Rate (R0) at subcellular, individual and population levels, respectively. At the sixth generation, Pb acclimated neonates were moved to a clean media for three more generations to check for recovery. D. magna showed no Pb effect on Net Reproductive Rate (R0). However, Pb stimulated reproduction, reduced lifespan and decreased AChE activity. Hatching delay and lifespan did not improve during the recovery process, indicating genetic adaptation. Food restriction reduced R0, lifespan, delayed hatching, and increased AChE activity; opposite outcomes were shown for D. similis. Full recovery shown by R0 suggests a physiological acclimation of D. similis. Under food restriction, the animals exhibited a reduction of R0 and lifespan, delayed hatching and increased AChE activity; however, with no Pb effect. The recovery process under food restriction showed that D. similis might not cope with Pb exposure, indicating failed recovery. Such outcomes indicate that a model species' sensitivity may not represent another's sensitivity.

The aim of this work was to investigate the microorganisms and their metabolites responsible for the spoilage of goose sausages produced in a small facility in Lombardy, a northern region of Italy. Spoilage was first detected by sensorial analysis using the “needle probing” technique; however, the spoiled sausages were not marketable due to the high ammonia and vinegar smell. The added starter culture did not limit or inhibit the spoilage microorganisms, which were represented by Levilactobacillus brevis, the predominant species, and by Enterococcus faecalis and E. faecium. These microorganisms grew during ripening and produced a large amount of biogenic amines, which could represent a risk for consumers. Furthermore, Lev. brevis, being a heterofermentant, also produced ethanol, acetic acid and a variation in the sausage colour. The production of biogenic amines was confirmed in vitro. Furthermore, as observed in a previous work, a second cause of spoilage can be attributed to moulds that grew during ripening; both the isolated strains, Penicillium nalgiovense, added as starter culture, and P. lanoso-coeruleum, present as environmental contaminant, grew between the meat and casing, producing a large amount of total volatile nitrogen, responsible for the ammonia smell perceived either in the ripening area or in the sausages. This is the first description of Levilactobacillus brevis predominance in spoiled goose sausage.

The Süttő 21 site is a fissure fill of the freshwater limestone of the Gazda quarry in Süttő. The material was collected between 2017 and 2019, the results are summarised in this article, with a special focus on the small vertebrate fauna of the site and its stratigraphic and paleoecological significance. The fissure fill can be placed around the early/middle Pleistocene boundary (ca. 1.1 and 0.77 Ma). The paleoecological analysis of the herpeto- and mammal fauna of the sequence indicates the proximity of a permanent water body. The lower part of the sequence is dominated by open habitat indicator taxa indicating a cool, dry climate. Towards the upper part of the sequence, the climate remained cool but became wetter, and the vegetation gradually changed to forest-steppe/open forest. The fauna of the Süttő 21 site can be compared with the material of sites, which are of similar age, thus revealing taxonomic and paleoecological differences between different areas of the country. While a warm, dry climate and open vegetation can be reconstructed in the Villány Hills around the early/middle Pleistocene boundary, the northern Hungarian areas had a cooler, wetter climate, and slightly more closed (grove, forest-steppe) vegetation during this period.

Three facts characterize the hailstorm of 30 August 2022 in the Catalan village of La Bisbal d'Empordà and its surroundings: first, the most dramatic, the death of a child hit by a hailstone. Second, the damage to most of the roofs and cars in the town. Finally, because of the record of hail size (more than 10 cm) in Catalonia in at least the last 30 years. This research focuses on the radar field comparison and the observations provided by an electronic survey of the study area. The results reveal that weather radar sub-estimated the hail size because of different factors. On the opposite, some reporters provided an inaccurate hour. The difference of three months between the hail event and the electronic survey is the probable cause of this mistake in the time estimation. However, the survey delay helped to avoid answers with larger hail sizes than those provided by the official spotters.

The Mont-Saint-Michel is known worldwide for its unique combination of the natural site and the Medieval abbey at the top of the rocky islet. But the Mont is also located within an estuarine complex, which is considerably silting up. For two decades, large-scale works were planned to prevent the Mont from being surrounded by the expanding salt meadows. The construction of a new dam over the Couesnon River, the digging of two new channels, and the destruction of the causeway were the main operations carried out between 2007 and 2015. The remote sensing approach is fully suitable for evaluating the real impact of the engineering project in both time and space, particularly the expected large-scale hydrosedimentary effects, for reestablishing the maritime landscape around the Mont. Sentinel-2 satellite data have been used for the period from 2015 to 2023. Aster data were used for the previous period covering 2000 to 2017. Aerial photographs and an ALOS scene have been also used. The remote sensing approach is based on time-series images. It allows identifying local or regional consequences and temporary or permanent effects. The migration of the different channels (especially for the new west and east Couesnon river courses) and the erosion-progradation balance of the vegetation through space and time are the main features to study. Between 2007 and 2023, the erosion of the salt meadows is significant to the south-west of the Mont (− 150 ha) but more limited to the south-east (− 65 ha). The erosion effect is limited to the immediate environment because the vegetation fringe of the uppermost tidal flat along the main dike is slightly increasing (+ 35 ha) to the west and to the east (+ 40 ha). During the same period, the sedimentation considerably increased to the north-east of the Bay, between the Bec d’Andaine, the Grouin du Sud and Tombelaine islet, which seems now facing the same silting-up problem. At this stage, the remote-sensing survey indicates mixed results for the engineering project.

The potential impacts of climate change on the distribution of tuna in Pacific Island Countries’ Exclusive Economic Zones have yet to be investigated rigorously, and so their persistence and abundance in these areas remain uncertain. Here, we estimate optimal fisheries areas for four tuna species; Albacore (Thunnus alalunga), Bigeye (Thunnus obesus), Skipjack (Katsuwonus pelamis), and Yellowfin (Thunnus albacares). We consider different climate change scenarios, RCP 2.6, RCP 4.5, RCP 6.0 and RCP 8.5, within a set of tuna catch records in the Exclusive Economic Zone of Tonga. Using environmental and CPUE datasets, species distribution modelling estimated and predicted these fisheries areas in the current and future climatic scenarios. Our projections indicate an expansion in area and a shift of productive areas to the southern part of this Exclusive Economic Zone of Tonga. This is an indication that future climatic scenarios might be suitable for the species under study however, changes in trophic layers, ocean currents and ocean chemistry might alter this finding. Information provided here will be relevant in planning future national actions towards proper management of these species.