Some of Iran's gas resources are known as sour gas because one of the major by-products of this gas is water. In fact, natural gas is combined with water vapor in underground reservoirs. In some areas, the amount of water vapor in natural gas is so high that it can be used as a source of drinking water. However, it should be noted that water vapor in natural gas may exacerbate corrosion in pipes and industrial equipment, and the combustion of more natural gas produces high temperatures that can lead to the production of nitrogen oxides (NOx), which They are the cause of air pollution. This is while the processed gas has a standard percentage composition in which the amount of water has the lowest position. The removal of moisture from natural gas is due to the need to prevent the reduction of the calorific value of the gas and also to purify the gas in order to achieve the necessary standards for delivering gas to petrochemicals, industries and domestic uses. The main goal of this research is to investigate the influencing parameters on zeolite TiO2 nanocomposite membranes in order to absorb moisture from gas. For this reason, with the construction of a TiZ-V membrane as a standard membrane, the result of the initial evaluation of a suitable membrane for gas dehumidification was made, and this membrane was placed as a standard for measuring the effect of the manufacturing parameters in a way that in each stage of membrane construction It was found that it was different from standard TiZ-V membrane only in terms of one parameter. This type of investigation made it possible to determine the effect of various effective parameters in membrane construction on efficiency. The findings showed that increasing the concentration of SiO2 has the greatest effect on increasing the water flux of the membrane. According to the other findings of this study, the effect of increasing the reaction time of the vapor phase carrier has been to reduce the process of paternity selectivity loss at higher pressures. Although due to the safety limitation of the equipment to measure the efficiency of the membrane at pressures higher than 7 bar, this measurement was not carried out, but charts were presented regarding the state of the water in the water, which were a measure of the superiority of the water in the water in comparison to the gas in the water, which is the higher water in the water It is an indicator of the appropriateness of the membrane's efficiency at its corresponding pressure, so that the examination of the difference between these two graphs shows the possibility of using the membrane at higher pressures

The TiO₂ nanostructures resulted by pyrolysis of TiCl₄ at low temperature of 80 ^oC are found to be a mixture of amorphous TiO₂ complexes and anatase nanostructure whose ratio depends on the pH of the pyrolysis medium. At low pH level, the resulting TiO₂ nanostructure is predominant anatase and gradually shifts to the amorphous TiO₂ complexes with pH level increasing. By means of heat treatment, the amorphous TiO₂ complexes can be converted back to the anatase nanostructure and then transform to rutile with the elevating temperature. Amongst of the TiO₂ nanostructure recovered from amorphous TiO₂ complexes, the anatase shows to be the most effective photocatalyst in decomposition of methylene blue.

In this research we are reporting gas sensing properties of TiO_2-x/TiO₂-based hetero-structure, which was ‘self-heated’ by current that at constant potential passed through the structure. Amperometric measurements were applied for the evaluation of sensor response towards ethanol, methanol, n-propanol and acetone gases/vapors. The sensitivity towards these gases was based on electrical resistance changes, which were determined by amperometric measurements of current at fixed voltage applied between Pt-based contacts/electrodes deposited on TiO_2-x/TiO₂-based layer. XRD analysis revealed the formation of TiO_2-x/TiO₂-based hetero-structure, which is mainly based on Ti₃O₅/TiO₂ formed during hydro-thermal oxidation based sensing layer preparation process. Additionally, photoluminescence and time-resolved photoluminescence decay kinetics based signals of this sensing structure revealed the presence of TiO₂ mainly in the anatase phase in the TiO_2-x/TiO₂-based hetero-structure, which was formed at 400°C annealing temperature. The evaluation of TiO_2-x/TiO₂-based gas sensing layer was performed at several different temperatures (25°C, 72°C, 150°C, 180°C) and at these temperatures different sensitivity to aforementioned gaseous materials was determined.

Electron-hole recombination and narrow range utilization of sunlight limit the photocatalytic efficiency of TiO2. We synthesized a carbon dots (CDs) modified TiO2 nanoparticles (NPs) with flower-like mesoporous structure, i.e., porous TiO2/CDs nanoflowers. Among such hybrid parti-cles, CDs worked as photosensitizers for the mesoporous TiO2 and enabled the resultant TiO2/CDs nanoflowers with a wide-range light absorption. Rhodamine B (Rh-B) was employed as a model organic pollutant to investigate the photocatalytic activity of the TiO2/CDs nanoflowers. The results demonstrated that the decoration of CDs on both TiO2 nanoflowers and P25 NPs enabled a significant improvement of the photocatalytic degradation efficiency compared with the pristine TiO2. TiO2/CDs nanoflowers with porous structure and larger surface areas than P25 showed a higher efficiency owing to prevent local aggregation of carbon materials. All the results revealed that the introduced CDs and the unique mesoporous structure, large surface areas and loads of pore channels of the prepared TiO2 NPs played important roles in the enhancement of the photocatalytic efficiency of the TiO2/CDs hybrid nanoflowers. Such TiO2/CDs composite NPs also opens a door for photodegradation, photocatalytic water splitting and enhanced solar sun-light as light source.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

In this study, nanostructured cerium-doped TiO2 (Ce-TiO2) films with the addition of different amounts of cerium (0.00, 0.08, 0.40, 0.80, 2.40, and 4.10 wt. %) were deposited on a borosilicate glass substrate, by flow coating sol-gel process. After flow coating, deposited films were dried at the temperature of 100 °C for 1 h, followed by calcination at the temperature of 450 °C for 2 h. For the characterization of sol-gel TiO2 films, the following analytic techniques were used: X-ray diffraction (XRD), thermal gravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry (DSC). Sol-gel derived Ce-TiO2 films were used for photocatalytic degrada-tion of the ciprofloxacin (CIP). The influence of the amount of Ce in TiO2 films, the duration of the photocatalytic decomposition, and the irradiation type (UV-A and simulated solar light) on the CIP degradation were monitored. Kinetics parameters (reaction kinetics constants and the half-life) of the CIP degradation, as well as photocatalytic degradation efficiency, were determined. The best photocatalytic activity was achieved by the TiO2 film doped with 0.08 wt.% Ce, under both UV-A, and solar irradiation.

In this study, carbon-quantum-dot (CQD)-decorated TiO2 was prepared using an ultrasonic doping method and applied in the photocatalytic degradation of naphthalene under sunlight irradiation. The CQDs were synthesized from a typical macroalgae via diluted sulfuric acid pretreatment and hydrothermal synthesis using an optimal design, i.e., 3 wt% and 200 oC, respectively. The CQD/TiO2 composite remarkably enhanced the photocatalytic activity. The degradation of naphthalene under a visible light environment indicated that there is a synergistic mechanism between CQDs and TiO2, in which the generation of reactive oxygen species is significantly triggered; in addition, the N that originated from the macroalgae accelerated the photocatalytic efficiency. Kinetic analysis showed that the photo-catalytic behavior of the CQD/TiO2 composite followed a pseudo-first-order equation. Consequently, our combined experimental approach not only provides a facile pretreatment process for bio-CQDs synthesis, but also delivers a suitable TiO2 photocatalyst for up-conversion, along with critical insights into the development of harmful macroalgae resources.

In this paper we propose a simple procedure to obtain multi-walled carbon nanotubes (MWCNT) decorated with TiO₂-Ag nanoparticles (MWCNT-TiO₂-Ag). MWCNT were decorated with TiO2-Ag via combined functionalisation with -OH and –COOH groups and polymer wrapping technique using poly(allylamine hydrochloride) (PAH). TiO₂ modified Ag nanoparticles were synthesized through Pechini method using mixture of acetylacetonate-modified titanium (IV) isopropoxide with silver nitrate (the Ag+/Ti4+ atomic ratio, is 0.5, 1,0, 1.5, 2.0 and 2.5 %, respectively) and the L(+)-ascorbic acid, as reducing agents. XRD analysis revealed the formation of nanocomposite containing CNT, TiO₂ (anatase and rutile) and Ag. By SEM was evidenced the presence of the nanoparticles on MWCNT surface. The increases of the ratio between Ag⁺ and Ti⁴⁺ decrease the band gap energy of the samples. In Raman spectra the characteristic vibration of the TiO₂, Ag and C atoms of graphite are identified. The photocatalytic activity of the MWCNT-TiO₂-Ag nanocomposite was assessed by examining the degradation of Allura red (E129) aqueous solution under UV irradiation. The dye photodegradation process follows a pseudo – first – order kinetic with respect to the Langmuir – Hinshelwood reaction mechanism.

The wide range of applications of nanoparticles (NPs) has increased the probability of environmental and occupational exposure. In a previous comparative study on cell line A549, we observed that oxidative stress caused by Co₃O₄ NPs affects the energetic homeostasis and the detoxification capacity, preventing autophagy induced by TiO₂ NPs. In this study, we have investigated the effects of NPs on the cell cycle.Cytofluorimetric analysis showed a slow-down of the cell cycle progression for both NPs, with increases in the percentage of resting cells in the G0/G1. These observations were confirmed by a reduced expression of all cyclins, especially of CCNE1 and CDK2, involved in the late stages of the G1 phase, coupled with a significant increase in the expression of p21 only for Co₃O₄ NP exposure. On the contrary, the effects of TiO₂ NPs were modest. Cell cycle related miRNA-34a, miRNA-126 and miRNA-1290 resulted increased at different early time-points (4-8h) but were down-expressed at 24h-48h only after TiO₂ NP exposure. Our results show that NPs have an antiproliferative effect and deregulate cell cycle on A549 cells. These effects should not be underestimated because regulation of cycle progression is crucial for cell survival and repair of genetic damage.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

This study presents a straightforward electrochemical and plasma deposition method for producing Cobalt-doped Blue-TiO2 nanotubes with enhanced catalytic properties. After a titanium plate has been anodized, specific procedures are carried out that cause oxygen vacancies to form inside the TiO2 nanostructures. The obtained catalysts were subjected to electrochemical tests (to identify charge transfer resistance and flat band potential), optical analysis (to determine the band gap and Urbach energy) and also characterized in terms of morphology, wettability and antibacterial effect in order to understand and analyze the impact of the Co doping method on the final catalyst characteristics. A hydrophilic film with star-shaped structures and with antibacterial effect was created when cobalt was electrochemically doped to Blue-TiO2 nanotubes. By using this electrochemical doping technique, the Urbach energy was raised from 1.171 to 3.836 eV while the band gap energy was decreased from 3.04 to 2.88 eV. Additionally, photodegradation experiments using artificial doxycycline (DOX) water were conducted to determine the practical relevance of the research findings. In areas like antimicrobial applications and photodegradation of DOX, these extra experiments aimed to show the practical applicability and potential advantages of the research findings.

TiO₂ nanorod as a superior nanostructure has attracted a lot of attention to exert in the photocatalytic and photoelectrocatlytic applications in recent years. Nevertheless, its practical usage is restricted by a number of limitations such as the large band gap energy, the low rate of photo-induced carriers generation and the high rate of charge carriers recombination. Therefore in this study, incorporation of TiO₂ nanorod with WO₃ is proposed as a suitable approach to overcome these defects. In this regard, WO₃-TiO₂ nanorod was constructed by a facile one pot hydrothermal method in two incessant steps and was then employed as a potent photoanode for photoelectrocatalytic hydrogen generation. The morphology, elemental compositions and optical properties were characterized by the FESEM, EDS and DRS analysis, respectively. Furthermore, voltammetry analyses were performed to assay the photoelectrochemical features of WO₃-TiO₂ nanorod. The results confirmed that the incorporation of TiO₂ nanorod with WO₃ not only significantly made the band gap energy narrower (from 3eV to 2eV), but also dramatically intensified the photocurrent density and photoconversion efficiency from 1mA.cm^-2 to 1.8mA.cm^-2 and from 0.3% to 0.45%, respectively. As a consequence of improving optical properties and photoelectrochemical features, WO₃-TiO₂ nanorod could generate 2.43 mmol H₂ during 100 min under UV irradiation, which was 1.71 times more than hydrogen generated over pure TiO₂ nanorod

Heavy metals are non-biodegradable and have a high toxicity effect to living things which makes their presence in the environment extremely dangerous. The method of handling heavy metals waste by photocatalysis techniques using TiO2/SiO2 composite showed a good performance in reducing harmful pollutants. In this study, SiO2 from Bengkulu beach sand was used as a support material for TiO2 photocatalyst to reduce Cr(VI) and Pb(II) concentrations. SiO2 was obtained through leaching techniques using NaOH as a solvent. The TiO2/SiO2 composite photocatalyst were synthesized using a solvothermal method at 130 °C and then characterized using XRD, FTIR, SEM and PSA. Based on the XRD diffractogram, the synthesized TiO2 showed the anatase structure while the SiO2 showed the amorphous structure. Ti-O-Si bond is defined in the IR spectra, which indicates that the relationship between TiO2 and SiO2 is a chemical interaction. The results of SEM and PSA characterizations show agglomerated spherical (round) particles with a mean particle size of 616.9 nm. The TiO2/SiO2 composite of 7:1 ratio showed the highest photocatalytic activity after 180 minutes of UV irradiation, with a concentration-decrease percentage of 93.77% and 93.55% for for Cr(VI) and Pb(II), respectively.

This study investigated dry reforming of methane with combined catalysts supported on γ-Al2O3 support doped with 3.0 wt. % TiO2. The physicochemical properties of all the catalysts were determined by inductively-coupled plasma/mass spectrometry metal analysis, nitrogen physisorption, X-ray diffraction, temperature programmed reduction/desorption, thermogravimetric analysis, and scanning electron microscopy. The addition of CeO2 and MgO to Ni strengthened the interaction between the Ni and the support. The catalytic activity results indicated that the CeO2 and MgO addition to Ni did not do much in retarding carbon deposition, but they improved the activity of the catalysts. Among the tested catalysts, it was found that the catalyst with the composition of 5.0 wt % NiO-10.0 wt % CeO2/3.0 wt %TiO2-γ-Al2O3 resulted in the highest CH4 and CO2 conversion with H2/CO mole ratio close to unity. The optimum reaction conditions in terms of reactant conversion and H2/CO mole ratio were achieved by varying space velocity and CO2/CH4 mole ratio.

In this work, pure TiO₂ and nano-magnetic of Fe₃O₄/TiO₂ were synthesized for degradation of 2,4-dichlorophenol (2, 4-DCP) as an organic pollutant. A range of analytical techniques including XRD, DRS, FESEM, and VSM were employed to reveal the crystal structure, morphology and property of the nanocomposite. The XRD results showed the prepared samples including 100% anatase phase. We obtained the band gap energy 2.9 and 2.8 eV for pure TiO₂ and Fe₃O₄/TiO₂ respectively. VSM results demonstrate that easy, fast separation and redispersion of Fe₃O₄/TiO₂ sample can be realized. We obtained 62% and 31% degradation of 2,4-DCP in the presence of Fe₃O₄/TiO₂ and pure TiO₂ under visible light respectively.

In this study, a novel binary nanocomposite system based on TiO₂-SiO₂ was functionalized with trimethylolpropane triacrylate (TMPTA) and characterized by XPS and XRD. Results revealed that TiO₂-SiO₂ nanoparticles were covalently functionalized. Functionalized nanoparticles at low concentrations (0.1 wt% and 0.5 wt%) were dispersed in acrylic acid acting as a polymer matrix. Nanocomposite coatings analysis demonstrate to achieve superhydrophilic properties as well as very good optical characteristics. Water contact angle characterization showed the functionalization effect by achieving a superhydrophilic behavior with a contact angle less than 5°. UV-Vis measurements demonstrated high optical transmittance above 95% for the coatings. Based on the obtained results a mechanism describing the chemical interactions of the constituents responsible for the synergy in the nanocomposite as well as the morphological play role in the behavior are presented.

The present study aims at deposition of zinc phosphate coatings with the incorporation of nano Titanium dioxide particles by chemical phosphating method. Zinc phosphate coatings were developed on low carbon steel by using nano TiO2 in the standard phosphating bath. The Coated low carbon steel samples were assessed for corrosion studies using electrochemical impedance spectroscopy and potentiodynamic polarisation techniques in 3.5% NaCl solution. Chemical composition of the coatings was analysed by energy dispersive X-ray spectroscopy (EDX). Significant variations in the coating weight, porosity and corrosion resistance were observed with the addition of nano TiO2 in the phosphating bath. Corrosion rate of nano TiO2 incorporated chemical phosphate coated samples was found to be 3.5 mpy which was 4 times less than the bare uncoated low carbon steel (~14 mpy). Electrochemical impedance spectroscopy studies revels in the reduction of porosity in nano TiO2 phosphate coated samples. It was found that nano TiO2 particles in the phosphating solution yielded phosphate coatings of higher coating weight, greater surface coverage and enhanced corrosion resistance than the normal zinc phosphate coatings (developed using normal phosphating bath).

MoS₂/TiO₂ nanostructures made of MoS₂ nanoparticles covering TiO₂ nanosheets have been synthesized, either via ex-situ or in-situ approaches. Morphology and structure of MoS₂/TiO₂ hybrid nanostructures have been investigated and imaged by means of X-ray diffraction (XRD) analysis and high-resolution transmission electron microscopy (HRTEM), while the vibrational and the optical properties have been investigated by Raman, Fourier-transform infrared spectroscopy (FTIR) and UV−visible (UV-Vis) techniques. The different stacking degrees together with the size distribution of the MoS₂ nanosheets, decorating the TiO₂ nanosheets, have been carefully obtained from HRTEM images. The nature of the surface sites on the main exposed faces of both materials has been detected by means of in-situ FTIR spectra of adsorbed CO probe molecule. The results coming from the ex-situ and in-situ approaches will be compared, by highlighting the role of the synthesis processes in affecting morphology and structure of MoS₂ nanosheets, including their curvature, surface defects, and stacking order. Some more, it will be shown that the in-situ approach is affecting the reactivity of the TiO₂ nanosheets too, hence in turn affects the MoS₂/TiO₂ nanosheets interaction.

A new two-step method for developing a nanocomposite of polypropylene (PP) decorated with photocatalytically active TiO2 nanoparticles (nTiO2) is proposed. This method involves low-temperature plasma functionalization of polypropylene followed by ultrasound-assisted anchoring of nTiO2. The nanoparticles, polymeric substrate, and resultant nanocomposite were thoroughly characterized using nanoparticle tracking analysis (NTA), microscopic observations (SEM, TEM, EDX), spectroscopic investigations (XPS, FTIR), thermogravimetric analysis (TG/DTA), and water contact angle (WCA) measurements. The photocatalytic activity of the nanocomposites was evaluated through the degradation of methyl orange. The individual TiO2 nanoparticles ranged from 2-6 nm in size. Oxygen plasma treatment of PP generated surface functional groups (mainly -OH and -C=O), transforming the surface from hydrophobic to hydrophilic, which facilitated efficient deposition of nTiO2. Optimized plasma treatment and sonochemical deposition parameters resulted in an active photocatalytic nTiO2/PP system, degrading 80% of methyl orange under UVA irradiation in 200 minutes. The proposed approach is considered versatile for the functionalization of polymeric materials with photoactive nanoparticles and, in a broader perspective, can be utilized for the fabrication of self-cleaning surfaces.

Polyphenols are the most common organic compounds in wine. They improve both the sensory aspects of wine and human health by activating antioxidant systems. Therefore, there is a great need for a simple, fast and accessible method to determine the polyphenol content of wine. The aim of this study is to characterize polyphenolic compounds in natural wine samples using an electrochemical method and a modified carbon paste electrode with TiO2 nanoparticles. This work is motivated by the promising improvement of the sensing properties of a TiO2 nanoparticle-modified carbon paste electrode observed in the electrooxidation of different polyphenols. Since the voltammetric response of wine is largely irreversible, another motivation was the possibility of improving the processing of voltammograms to obtain data indicative of wine polyphenols, based on the approach described in the seminal work by Espinoza et al. The modified electrode studied provides an improved and reproducible voltammetric response of gallic acid in wine samples and provides a good basis for further development of an integrated sensor/data system with the possibility of wider application for the quantification of gallic acid as a flavor and visually relevant parameter in winemaking.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

In this research, first a binary nanocomposite of magnetic recyclable photocatalyst Fe₃O₄/TiO₂, was synthesized by sol gel technique. Then, in order to enhance the photocatalytic activity of the synthesized nanocomposite, it was deposited by silver nanoparticles for using in degradation of organic pollutants 2, 4-dichlorophenol (2, 4-DCP) under visible light. A range of analytical techniques including XRD, FESEM/EDX, DRS, VSM and N₂ physisorption were employed to reveal the crystal structure, morphology and property of the nanocomposites. We obtained 32% and 55% degradation of 2, 4-DCP under visible light after 180 min irradiation in the presence of Fe₃O₄/TiO₂ and Fe₃O₄/TiO₂/Ag respectively. Thus, the excellent visible light photocatalytic activity of Fe₃O₄/TiO₂/Ag sample can be attributed to the surface plasmon resonance effect of Ag nanoparticles deposited on Fe₃O₄/TiO₂ nanocomposite.

In this work, TiO₂ QDs modifed NiO nanosheets was employed to imporve the room-temperature NO₂ sensing properties of NiO. The gas-sensing studies showed that the response of nanocomposites with the optimal ratio to 60 ppm NO₂ was nearly 10 times larger than that of bare NiO, exhibiting potential application in gas-sensing. Considering the commonly reported immature mechanism that the effective charge transfer between two phases contribute to enhanced sensitivity, QDs sensitization mechanism was further detailed by designing a seirs of contrast experiments. First, the important role of QDs size effect was revealed by comparing a little enhanced sensitivity of TiO₂ particle-modified NiO with largely enhanced senstivity of TiO₂ QDs-NiO. Second, and more important, the direct evidence of heterointerface charge transfer efficiency was detailed by extracted interface bond (Ti-O-Ni) using XPS peak fitting. We hope this work can provide guideline to design more QDs-modified nanocomposites with the higher sensitivty for practical application.

This work emphasizes to use silver decorative method to enhance the antibacterial activity of TiO₂ and ZnO nanoparticles. These silver decorated nanoparticles (hybrid nanoparticles) were synthesized by using sodium borohydride as a reducing agent, with the weight ratio of Ag precursors: oxide nanoparticles = 1: 30. The morphology and optical property of these hybrid nanoparticles were investigated using transmission electron microscopy (TEM) and UV–vis spectroscopy. The agar-well diffusion method was used to evaluate their antibacterial activity against both Staphylococcus aureus and Escherichia coli bacteria, with or without light irradiation. The TEM images indicated clearly that silver nanoparticles (AgNPs, 5-10 nm) were well deposited on the surface of nano-TiO₂ particles (30-60 nm). Besides, smaller AgNPs (< 2 nm) were dispersed on the surface of nano-ZnO particles (20-50 nm). UV-vis spectra confirmed that the hybridization of Ag and oxide nanoparticles led to shift the absorption edge of oxide nanoparticles to the lower energy region (visible region). The antibacterial tests indicated that both oxide pure nanoparticles did not exhibit inhibitory against bacteria, with or without light irradiation. However, the presence of AgNPs in their hybrids, even at low content (< 40 mg/mL) leads to a good antibacterial activity and the higher inhibition zones under light irradiation as compared to that in dark was observed.

This research was presented the special designed microfluidic device generated for sperm separation based on assumption of different surface electrical charged of sperms X and Y. However, to avoid ethical problem, the microfluidic chip has been tested with the mimic electrical charged particles, TiO₂-coated Polystyrene beads, (TiO₂-coated Ps-beads), instead of spermatozoa. The work has been separated into three main parts. Firstly, the simply but efficient fabrication of negatively charged TiO₂-coated Ps-beads has been presented. In addition, various characterization techniques such as X-ray diffraction (XRD), Tungsten Scanning Electron Microscopy (W-SEM) with energy-dispersive X-ray spectroscopy (EDS) mode, and X-ray Absorption Spectroscopy (XAS), have been reported in this work to elucidate the reasons behind the persistence of negatively charged on the surface of TiO₂-coated Ps-beads. Results show that the fabricated TiO₂-coated Ps-beads was partly coated in the mixed forms of amorphous Ti⁴⁺ and had caused a negatively charge to appear on the surface after fabrication and had sustained its electrical charged for long. Secondly, process of simulation and fabrication of microfluidic device was presented. Finally the negatively charged TiO₂-coated Ps-beads were tested in this microfluidic devices. For design of microfluidic devices integrated with a couple of microelectrodes, the simulated structures were fabricated by photolithographic technique and tested with the Ps-beads. Percentage of validation for Ps-beads separation indicated that the 100 mm-distance-between-electrodes microfluidic device exhibits to be the highest performance prototype at 86.96%. For further confirmation, another model so called the single path prototype has been established. It is confirmed by 92.59% of validation for the utilization of the device. The successfully designed microfluidic devices can be examined with actual spermatozoa later. Furthermore, process to fabricate the negatively charged TiO₂-coated Ps-beads can be established as testified samples for development of other microfluidic devices.

Hybrid metal-halide perovskites have emerged as leading class of semiconductors for photovoltaic devices with remarkable light harvesting efficiencies. The formation of methylammonium lead iodide (CH₃NH₃PbI₃) perovskite into mesoporous titania (TiO₂) scaffold by a sequential deposition technique is known to offer better control over the perovskite morphology. The growth reactions at the mesoporous TiO₂ film depend on reactants concentration in the host matrix and the reaction activation energy. Here, we are characterizing formation of CH₃NH₃PbI₃ perovskite in mimic solar cell photoelectrodes utilizing the developed NanoPlasmonic Sensing (NPS) approach. Based on dielectric changes at the TiO₂ mesoporous film interface, the technique provides time-resolved spectral shifts of the localized surface plasmon resonance that varies widely depending on the different operating temperatures and methylammonium iodide (CH₃NH₃I) concentrations. Analytical studies included Ellipsometry, Scanning Electron Microscopy, and X-ray diffraction. The results show that perovskite conversion can be obtained at lower CH₃NH₃I concentrations if reaction activation energy is lowered. A significant finding is that the NPS response at 350 nm mesoporous TiO₂ can widely change from red shifts to blue shifts depending on extent of conversion and morphology of perovskite formed at given reaction conditions.

Some contaminants of emerging concern (CECs) are known to survive conventional wastewater treatment plants, which introduce them back to the environment and can potentially cycle up in drinking water supplies. This is especially concerning because of the inherent ability of some CECs to induce physiological effects in humans at very low doses. Advanced oxidation processes (AOPs) such as TiO2 based photocatalysis are of prominent interest for addressing CECs in aqueous environments. Natural water resources often contain dissolved metal cations concentrations in excess of targeted CEC concentrations. These cations may significantly, adversely impact degradation of CECs by scavenging TiO2 surface generated electrons. Consequently, simple pseudo first order or Langmuir-Hinshelwood kinetics are not sufficient for reactor design and process analysis in some scenarios. Rhodamine B dye and dissolved copper cations were studied as reaction surrogates to demonstrate that TiO₂ catalyzed degradation for very dilute solutions is very nearly completely due to homogeneous reaction with hydroxyl radicals and that in this scenario the hole trapping pathway has negligible impact. Chemical reaction kinetic studies were then carried out to develop a robust model for RB/metal reactions that is exact in the electron pathways for hydroxyl radical production and metal scavenging.

A four stage semi-pilot scale RFR reactor with ceramic disks as support for TiO₂ modified with silver particles was developed for the removal of organic pollutants. The design presented in this article is an adaptation of the rotating biological reactors (RBR) and its coupling with the modified catalyst provides additional advantages to designs where a catalyst in suspension is used. The optimal parameter of rotation was 54 rpm and the submerged surface of the disks offer a total contact area of 387 M². The modified solid showed a decrease in the value of its bandgap compared to commercial titanium. The system has a semi-automatic operation with a maximum reaction time of 50 h. Photo-activity tests show high conversion rates at low concentrations. The results conform to the Langmuir heterogeneous catalysis model.

Ionic liquids (ILs) have gained interest among researchers due to its tunable properties that can be used in wide applications. However, toxicity and bio-degradation studies of ILs proved that most of the aromatic ILs, such as imidazolium is highly toxic and non-biodegradable. Several advance oxidation processes (AOPs) have been investigated by researchers to evaluate the efficiency of the systems for the removal of ILs from wastewater. However, the issue on relative high cost and environmental concern has limited the application of these AOPs in industry. In this research, photocatalytic study using hybrid nano-materials was conducted to evaluate the efficiency of this system as an alternative AOP system for removal of ILs from wastewater. The synergistic effect of adsorption-photodegradation was introduced by depositing Fe-TiO₂ onto the functionalized activated carbon (AC). Nano-TiO₂ was synthesized using micromulsion method before modification with transition metal and deposited onto the oxidized AC. Photodegradation reaction of 1-butyl-3-methylimidazolium chloride [bmim]Cl was investigated under simulated visible light irradiation. It was observed that the overall efficiency of the system was increased with the increasing amount of Fe dopant. Investigation on the extrinsic factors such as solution pH, initial concentration of ILs and photocatalyst dosage showed to significantly affect the overall efficiency of the systems where the optimum condition for the system was observed at pH 10, with initial ILs at 1mM at 1 g/L of photocatalyst. The best performance photocatalyst was 0.2Fe-TiO₂/AC.

In the last decades, numerous studies indicated the substantial role semiconductors could play in photocatalytic processes for environmental applications. Materials that contain a semi-conductor as a photo-catalyst have a semi-permanent capacity for removing harmful gases from the ambient air. In the present work, the focus is on TiO2. Heterogeneous photo-catalysis using TiO2 leads to the degradation of NO/NO2, benzene, toluene, and other priority air pollutants once in contact with the semiconductor surface. Preliminary evidence indicates that TiO2 containing construction materials and paints efficiently destroy the ozone precursors NO and NO2 up to 80% and 30%, respectively. Therefore, the development of innovative coatings containing TiO2 as a photo-catalyst was in the foreground of research activities with the aim to be used as building and construction materials mainly outdoors, e.g. on building facades in high traffic roads for the degradation of priority air pollutants (NOx and volatile organic compounds) in the polluted urban atmosphere. Though the advantages connected with the application of TiO2 due to its band gap of 3.2 eV are limited. TiO2 is effective only in the UV-region (ca. 5%) of the solar spectrum with wavelengths λ

Formaldehyde (HCHO), an indoor volatile organic compound, is seriously harmful to human health. Therefore, green and effective decomposition of HCHO is essential. TiO2 has been employed for the degradation of HCHO via photocatalytic generation of reactive oxygen species (ROS) (O2-, ·OH), yet the low specific surface area of crystalline TiO2 depressed the catalytic performance. Herein, we prepared TiO2 aerogels with high specific surface area and high porosity by sol-gel method, and added PVA to introduce flexible molecular chains for pore size regulation. The photocatalytic performance test verifies that the pore size of TiO2 aerogel is one of the important factors for HCHO decomposition. Notably, through the establishment of theoretical model and calculation, we validated that the efficiency of HCHO decomposition is related to the oxygen pressure in the pores of TiO2 aerogel, and the oxygen pressure is inversely proportional to the pore size. Accordingly, the optimal pore size of TiO2 aerogel for the photocatalytic HCHO decomposition is 2 nm-10 nm. This study provides a theoretical idea for TiO2 aerogels in the decomposition reaction of HCHO, which is expected to inspire more breakthroughs in the study of TiO2 aerogels for green chemistry.

The novel ternary composites, BiOBr-TiO2-attapulgite (BTA), were synthesized using a simple hydrothermal and water-bath method, exhibiting excellent photocatalytic performance to mul-tiple xanthates. For BTA photocatalyst, TiO2 and BiOBr were uniformly loaded on the surface of acid-activated attapulgite. As a widely used collector in mining processes, sodium ethyl-xanthate (SEX) was selected as the target pollutant due to its high toxicity. The BTA ternary photocatalyst demonstrated significantly higher adsorption and photocatalytic degradation performance compared to TiO2 nanoparticles, BiOBr nanosheets, and BiOBr-TiO2 heterojunction. Structural characterization and experimental results indicated that the exceptional photocatalytic degrada-tion efficiency of BTA was mainly attributed to the formation of heterojunction between BiOBr and TiO2, as well as the presence of additional active adsorption sites provided by attapulgite. Free radical scavenging experiments and EPR results confirmed that the photogenerated holes were the predominant active species to photodegrade SEX throughout the entire experiment. The LC-MS results provided insight into potential degradation pathways of SEX. This research demonstrates that BTA, as a novel triple composite material, achieves rapid and complete degradation to 20 mg/L SEX within 20 min. This work presents a novel approach to synthesize mineral-based photo-catalysts, which have broad prospects for application in flotation wastewater treatment.

In recent years, there has been growing interest in thermal spray techniques using suspension or solution-based coatings. These techniques offer precise control over particle size and microstructure, improving feedstock flowability and allowing for high-quality coatings customization. Spray parameters, such as stand-off distance (SOD) and feedstock flow rate, can alter the performance and characteristics of these coatings. Geothermal power plant heat exchangers often face issues like corrosion, scaling, and fouling. These issues could be mitigated, at least in part, by the use of spray coatings. In this study, TiO2 coatings were applied to a carbon steel substrate using suspension plasma spray (SPS) to enhance the performance of geothermal heat exchanger materials. The impact of SOD (50, 75, and 100mm) and feedstock flow rate (10, 20, and 30 ml/min) on these coatings was examined through various techniques, including SEM, profilometry, XRD, and adhesion testing. The results demonstrated that coatings deposited using 10ml/min feedstock flow rate were well-adhered to the substrate due to efficient melting of coating material but as the SOD and feedstock flow rate increase due to poor thermal and kinetic energy exchange between the torch and feedstock particles, adhesion between coating and substrate decreases. smaller SODs led to more compact coatings, while higher feedstock flow rates increased coating porosity. Smaller SODs and lower flow rates resulted in well-adhered coatings, offering valuable insights for advancing geothermal heat exchanger coatings.

Heat transfer fluids are used in various industrial systems to maintain them in perfect operating conditions. Extensive research efforts have been dedicated to enhance the thermal properties of these heat transfer fluids to improve their efficiency. Developing nanofluids is a potential candidate for such enhancements. This study investigates the impact of incorporating TiO2 nanoparticles into two types of oils: transformer oil (NYTRO LIBRA) and virgin coconut oil (manufactured by Govi Aruna Pvt. Ltd.) at different temperatures and with varying volume fractions. The nanofluids were prepared using a two-step method by adding CTAB (Cetyltrimethylammonium bromide) surfactant. To minimize nanoparticle agglomeration, this study employed relatively low-volume fractions. Thermal properties by means of thermal conductivity, thermal diffusivity, and volumetric heat capacity were measured in accordance with ASTM (American Society for Testing and Materials) standard methods, using a multifunctional thermal conductivity meter (LAMBDA thermal conductivity meter). The measured thermal conductivity values were compared with theoretical models and previous research findings. It was confirmed that the modification of thermal properties was enhanced by doping TiO2 nanoparticles with different volume fraction.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

Photocatalytic technology based on specific band structure of semiconductors offers a promising way to solve the urgent energy and environmental issues in modern society. In particular, hydrogen production from water splitting over semiconductor photocatalysts attracts great attention owing to the clean source and application of energy, which highly depends on the performance of photocatalysts. Among the various photocatalysts, TiO2 has been intensively investigated and used extensively due to its outstanding photocatalytic activity, high chemical stability, non-toxicity and low cost. However, pure TiO2 has a wide band gap of approximately 3.2 eV, which limits its photocatalytic activity for water splitting to generate hydrogen only under ultraviolet light, excluding most of the inexhaustible sunlight for human beings. Fortunately, the band gap of semiconductors can be manipulated, in which introducing oxygen defects is one of the most effective measures to narrow the band gap of titanium oxides. This review starts out by the fundamentals of photocatalytic water splitting for hydrogen production over TiO2, discusses the latest progress in this field, and summarizes the various methods and strategies to induce oxygen defects in TiO2 crystals. Then, the next section outlines the modification approaches of oxygen-deficient titanium oxide (TiO2-δ) to further improve its photocatalytic performance. Finally, a brief summary and outlook of the researches on TiO2-δ photocatalysts for water splitting to produce hydrogen were presented.

The photocatalytic hydrogen evolution reaction (HER) by water splitting has been studied, using catalysts based on TiO2 nanowires (TiO2NWs), which were synthesized by a hydrothermal procedure. This nanomaterial was subsequently modified by incorporating different loadings of gold nanoparticles (AuNPs) on the surface, previously exfoliated MoS2 nanosheets, and CeO2 nanoparticles (CeO2NPs). These nanomaterials, as well as the different synthesized catalysts, were characterized by electron microscopy (HR-SEM and HR-TEM), XPS, XRD, Raman, Reflectance and BET surface area. HER studies were performed in aqueous solution, under irradiation at different wavelengths, which were selected through the appropriate use of optical filters. The results obtained show that there is a synergistic effect between the different nanomaterials of the catalysts. The specific area of the catalyst, and especially the increased loading of MoS2 and CeO2NPs in the catalyst substantially improved the H2 production. Recyclability studies showed only a decrease in activity of approx. 7% after 15 cycles of use, which opens many possibilities regarding the potential use and scaling of these heterostructures in photocatalytic production of H2 from water.

Direct interaction with the neuronal cells is a prerequisite to deciphering useful information in understanding the underlying causes of diseases and functional abnormalities in the brain. Precisely fabricated nanoelectrodes provide the capability to interact with the brain in its natural habitat without compromising its functional integrity. Considerable research has been focused on the employment of vertical nanotubes as nanoelectrodes due to large-scale intracellular recording capability and longer-term intracellular access that arise from their unique geometry. Despite many types of nanotube structures reported in the literature, a limited subset of the nanotubes has been investigated for neural interfacing. This work reports on the fabrication and optimisation of vertically oriented titania nanotube arrays as a scalable electrode platform for neural interface application. To this end, the doping was performed by incorporating a selected group of biologically active metallic ions, including zinc, strontium, and copper, into TiO2 lattice and its effect was studied with respect to the structural, electrochemical and biological properties of the nanotube arrays. It was found that doping can change the length, diameter and wall thickness of the nanotubes. Among pure and doped samples, the copper-doped TiO2 nanotubes demonstrated the highest electrochemical and biological performance. Our results suggest that the doping can be used as a promising method to optimise the properties of nanotube arrays for the development of high-performance neural electrodes.

The photocatalysis process over N-doped TiO2 under visible light is examined for Pb(II) oxidation to form the less toxic and handleable PbO2 suggesting a new method for Pb(II) remediation. The doping TiO2 with N element was conducted by simple hydrothermal technique and using urea as the N source with various concentrations. The doped photocatalysts were characterized by DRUVS, XRD, FTIR and SEM-EDX instruments. Photocatalysis of Pb(II) through batch experiment was performed for evaluation of the doped TiO2 activity under visible light, with applying various fractions of N doped, photocatalyst weigh, irradiation time, and solution pH. The research results attributed that N doping has been successfully performed, that shifted TiO2 absorption into visible region, allowing it to be active under visible irradiation. The photocatalytic removal of Pb(II) under visible ligth over N-TiO2 showed more effective than that of over the un-doped photocatalyst. The removal of Pb(II) has notably taken place through oxidation, that may form PbO2. The highest photocatalytic oxidation of Pb(II) 15 mg/L in 25 mL of the solution could be reached by using TiO2 doped with 10%w of N, 15 mg of N-TiO2 weight, 30 minutes of time, and at pH 8, suggesting a feseable method for Pb(II) remediation.

The preparation of immobilized graphene–based photocatalyst layers is highly desired for environmental applications. In this study, the preparation of an immobilized reduced graphene oxide (rGO)/TiO₂ composite by electrophoretic deposition (EPD) was optimized. It enabled quantitative deposition without sintering and without the use of any dispersive additive. The presence of rGO had beneficial effects on the photocatalytic degradation of 4-chlorophenol in an aqueous solution. A marked increase in the photocatalytic degradation rate was observed, even at very low concentrations of rGO. Compared with the TiO₂ and GO/TiO₂ reference layers, use of the rGO/TiO₂ composite (0.5 wt% of rGO) increased the first-order reaction rate constant by about 70%. This enhanced performance was due to the increased formation of hydroxyl radicals that attacked the 4-chlorophenol molecules. The direct charge transfer mechanism had only limited effect on the degradation. Thus, EPD-prepared rGO/TiO₂ layers appear to be suitable for environmental application.

Rapid progress in the development of highly efficient nanoparticle-based construction technologies has not always been accompanied by a corresponding understanding of their effects on human health and ecosystems. Here, we compare toxicological effects of pristine TiO₂, ZnO and SiO₂, and coated SiO₂ nanoparticles and evaluate their suitability as additives to consolidants of weathered construction materials. First, WST-1 and LDH assays were used to determine the viability of human alveolar A549 cells at various nanoparticle concentrations (0–250 μg mL⁻¹). While the pristine TiO₂ and coated SiO₂ nanoparticles did not exhibit any cytotoxic effect up to the highest tested concentration, the pristine SiO₂ and ZnO nanoparticles significantly reduced cell viability. Second, as all the developed nanoparticle-modified consolidants increased the mechanical strength of weathered sandstone, the decisive criterion for the selection of the most suitable nanoparticle additive was as low toxicity as possible. We believe that this approach will be of high importance for industry to identify materials representing top functional properties and low toxicity at an early stage of the product development.

Two-dimensional arrays of hollow nanotubes made of TiO2 are a promising platform for sensing, spectroscopy and light harvesting applications. Their straightforward fabrication via electrochemical anodization, growing nanotube pillars of finite length from a Ti foil, allows precise tailoring of geometry and, thus, material properties. We investigate these photonic crystal structures with respect to reduction of front surface reflection, achievable field enhancement, and photonic bands. With the Rigorous Coupled Wave Analysis (RCWA), we study the optical response of photonic crystals made of thin-walled nanotubes relative to the bare Ti foil substrate, including under additional charge carrier doping.

In this study, TiO2 nanostructured coatings on Ti-6A-4V alloys were fabricated by two methods: H2O2 oxidation and RF sputtering. In the annealing temperature range of 25 C - 500 C, there were the peaks at 35, 37, 40 and 52 corresponding to {100}, {002}, {101} and {102} crystal planes of hcp structure of α-Ti. At the annealing temperature of 600 C, there was the presence of peaks corresponding to crystal planes of anatase and rutile TiO2. The relative intensities of anatase and rutile phases of the sample fabricated by RF sputtering were 3.62 and 10.25 %, respectively; while those of the sample fabricated by H2O2 oxidation were 21.27 and 3.20 %, respectively (The relative intensity of α-Ti phase was 100 %). The results investigated the peak shift of α-Ti phase in TiO2/Ti-6Al-4V nanostructured coatings fabricated by the two methods which was reasonably explained from the difference in the thermal expansion coefficients of Ti alloy and TiO2 components, as well as the difference in the ratio of anatase to rutile phases.

Hot rolling tests of a low-alloy steel were conducted at a rolling temperature of 850 ℃ under different lubrication conditions, including benchmarks (dry condition and water) and water-based nanolubricants containing different concentrations of nano-TiO₂ from 1.0 to 8.0 wt%. The effects of nanolubricants on rolling force, surface roughness, thickness of oxide scale and microstructure were systematically investigated through varying nano-TiO₂ concentrations. The results show that the application of nanolubricants can decrease the rolling force, surface roughness and oxide scale thickness of rolled steels, and refine ferrite grains. In particular, the nanolubricant containing an optimal concentration (4.0 wt%) of nano-TiO₂ demonstrates the best lubrication performance, owing to the synergistic effect of lubricating film, rolling, polishing and mending generated by nano-TiO₂.

The Cu cocatalyst supported on the surface of TiO2 photocatalysts has demonstrated unique activity and selectivity in photocatalytic CO2 reduction. The valence state of copper significantly influences the catalytic process; however, due to the inherent instability of copper's valence states, the precise role of different valence states in CO2 reduction remains inadequately understood. In this study, CuOx/TiO2 catalysts were synthesized using an in-situ growth reduction method, and we investigated the impact of various valence copper species on CO2 photocatalytic reduction. Our results indicate that Cu+ and Cu0 serve as primary active sites, with the selectivity for CH4 and CO products during CO2 photoreduction being closely related to their respective ratios on the catalyst surface. The adsorption and activation mechanisms of CO on both Cu+ and Cu0 surfaces are identified as critical factors determining product selectivity in photocatalytic processes. Furthermore, it is confirmed that Cu+ primarily facilitates CH4 production while Cu0 is responsible for generating CO. This study provides valuable insights into developing highly selective photocatalysts.

Photocatalysis is a promising method for methylene blue (MB) degradation due to its effectiveness and environmental compatibility. Among photocatalysts, titanium dioxide (TiO2) has been widely used for MB degradation due to its exceptional photocatalytic activity. However, the wide bandgap limits the degradation efficiency of TiO2 under visible light. Herein, an interstitial nitrogen-doped TiO2 (5%NT/TiO2) used thiourea as the N source is fabricated for the visible light-derived MB degradation. 5%NT/TiO2 exhibits an extended visible light absorption range. Besides, photoelectrochemical measurement shows an improvement in photocurrent response and charge transfer behavior on N/TiO2. Thus, 5%NT/TiO2 has enhanced photocatalytic activity compared to pristine TiO2 and substitutive N-doped TiO2 (5%NAB/TiO2). The accelerated photocatalytic MB degradation process on N/TiO2 should be mainly attributed to the interstitial N doping, which causes the appearance of new energy states and extended optical properties.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

The aim of this study was to develop sago starch-based bionanocomposite films containing TiO2 nanoparticles and Penganum harmala extract (PE) to increase the shelf life of chicken fillets. First, sago starch films containing different levels of TiO2 nanoparticles (1, 3 and 5%) and PE (5, 10 and 15%) were prepared, and the thickness, barrier properties, and antibacterial activity of the films. Then, the produced films were used for the chicken fillets packaging and the physicochemical and antimicrobial properties of samples were examined during 12-day storage at 4°C. The results showed that the addition of the combination of nanoparticles and extract and increasing their levels in the films increased the antibacterial activity against gram-positive and gram-negative bacteria. The results also demonstrated that during the storage period, the pH, total volatile basic nitrogen (TVB-N), and the number of aerobic mesophilic bacteria, psychrophilic bacteria, coliforms, molds and yeasts in fillets increased (p&lt;0.05). However, coating the fillets with bionanocomposites can significantly reduce the rate of change in chemical properties and microbial growth of the samples. This sample increased the shelf life of the fillets by at least 8 days compared to the control sample.

Microplastics (MPs) and nanoplastics (NPs) are distributed and transferred among the four major environmental compartments (air, water, soil, and biota) and have been already found in humans, making crucial to develop remediation technologies to tackle this kind pollution. Photocatalysis can be used to eliminate MPs present in contaminated wastewater effluents before their discharge into waterbodies. In this work, several green TiO2-based semiconductors were prepared using the extrapallial fluid (EPF) of Mytilus edulis sea water mussels as doping precursor. The semiconductors were then used as films or powders to photocatalytically degrade polystyrene (PS) NPs and MPs and polyethylene (PE) MPs. It was found that the obtention of green TiO2-based semiconductors with good characteristics for photocatalytic purposes (anatase crystalline phase, presence of porosity, activity in visible light and high surface area) seems not enough to achieve high degradation efficiency. The operational conditions of the reaction system should be also taken into account. For instance, the convenience of using semiconductors in the form of films can be overcome by their limited exposed surface area or the null adsorption of the semiconductor in the MPs particles. Additionally, crystallinity of the semiconductor can be a more determinant factor to take into account when performing photocatalysis of MPs.

Read-Across Structure-Activity Relationship (RASAR) is an emerging cheminformatic approach that combines the usefulness of a QSAR model and similarity-based Read-Across predictions. In this work, we have generated a simple, interpretable, and transferable quantitative-RASAR (q-RASAR) model which can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials. The data set involves 29 TiO2-based nanomaterials which contain specific amounts of noble metal precursors in the form of Ag, Au, Pd, and Pt. The data set was rationally divided into training and test sets and the Read-Across-based predictions for the test set were generated using the tool Read-Across-v4.1 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. The hyperparameters were optimized based on the training set data and using this optimized setting, the Read-Across-based predictions for the test set were obtained. The optimized hyperparameters and the similarity approach, which yields the best predictions, were used to calculate the similarity and error-based RASAR descriptors using the tool RASAR-Desc-Calc-v2.0 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. These RASAR descriptors were then clubbed with the physicochemical descriptors and were subjected to features selection using the tool Best Subset Selection v2.1 available from https://dtclab.webs.com/software-tools. The final set of selected descriptors was used to develop multiple linear regression based q-RASAR models, which were validated using stringent criteria as per the OECD guidelines. Finally, a random forest model was also developed with the selected descriptors. The final machine learning model can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials superseding previously reported models in the prediction quality.

Titanium and its alloys are used biomaterials for medical and dental applications, due to their mechanical and physical properties. The surface modifications of titanium with bioactive molecules can increase the osseointegration by improving the interface between the bone and implant. Titanium dioxide nanotubes (TiO₂NTs) have excellent bioactivity inducing cell adhesion, spreading, growth and differentiation. In this work, TiO₂NTs were functionalized with a lectin from the plasma of the fish Oreochromis niloticus aiming to favour the adhesion and proliferation of osteoblast-like cells, improving its biocompatibility. The TiO₂NTs were obtained by anodization of titanium and annealed at 400 °C for 3 h. The resulting TiO₂NTs were characterized by high-resolution scanning electron microscopy. The successfully incorporation of OniL on the surface of TiO₂NTs by spin coating was demonstrated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIE) and attenuated total reflection-Fourier transform infrared spectrum (ATR-FTIR). Our results showed that TiO₂-NTs were successfully synthesized in a regular and well-distributed way. The functionalization of TiO₂-NTs with OniL favoured adhesion, proliferation, and the osteogenic activity of osteoblast-like cells, suggesting its use to improve the quality and biocompatibility of titanium-based biomaterials.

Herewith we report a facile synthesis of zinc oxide doped with (5, 10, 15, and 20 wt%) titanium oxide nanocomposites in gelatin under ultra-sonication. The X-ray diffraction (XRD) data revealed ZnO the formation in addition to a rutile phase TiO2. The ZnO phase size decreased, and the rutile TiO2 phase increased with a TiO2 loading increment. The scanning electron microscopy (SEM) displayed a combination of spherical and hexagonal particles with a 60 – 80 nm size distribution. The prepared nanostructures photocatalytic activity was assisted using Rhodamine B dye, where they showed enhanced photodegradation competence under visible light irradiation. The kinetics of photodegradation followed the first-order kinetics with the 20 % wt sample having the maximum activity. The mechanistic investigation revealed the dominance of h+ and •O2- species during the dye photodegradation. The results indicate the potential application of such gelatin stabilized nanostructures for dye illumination from aqueous solutions under sunlight.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS₃), a layered semiconductor that attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS₃ in air above 300 °C gradually converts it into TiO₂, a semiconductor with a wide bandgap of 3.2 eV with applications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS₃ nanoribbons and its influence on the optoelectronic properties of TiS₃-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS₃ devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase of the bandgap of titanium oxysulfide (TiO_2-xS_x) when increasing the amount of oxygen and reducing the amount of sulfur.

Photoelectrocatalytic water splitting by using various TiO₂ nanostructures is a promising approach to generate hydrogen without harmful byproducts. However, their effective performance is restricted by some drawbacks such as high rapid electron-hole pair recombination and backward reaction producing H₂O. Thus in this study, the probability of enhancing hydrogen generation rate by adding methanol as a sacrificial agent to the anodic chamber of a two-compartment photoelectrochemical cell is investigated. Herein, one-dimensional elongated TiO₂ nanorods that were fabricated via a facile one-pot hydrothermal method are utilized as potent photoanode. Voltammetric characterizations confirm that addition of alcoholic sacrificial agent has a significant effect on photoelectrochemical properties of TiO₂ nanorods which by adding 10 wt% of methanol, the photocurrent density and photoconversion efficiency increased from 0.8mA.cm^-2 to 1.5mA.cm^-2 and from 0.28% to 0.45%, respectively. The results of photoelectrocatalytic water splitting indicated that the hydrogen generation rate in the presence of methanol was about 1.2 times higher than that from pure water splitting. These enhancements can be attributed to the key role of methanol. Methanol molecules not only inhibit the electron-hole pair recombination but also accelerate the hydrogen generation rate by sharing their hydrogen atoms.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

Various crystallite size estimation methods were used to analyze X-ray diffractograms of spherical cerium dioxide and donut-like titanium dioxide anatase nanoparticles aiming to evaluate their reliability and limitations. The microstructural parameters were estimated from Scherrer, Monshi, Williamson-Hall, and their variants: i) uniform deformation model, ii) uniform strain deformation model, and iii) uniform deformation energy density model, and also size-strain plot, and Halder-Wagner method. For that, and improved systematic Matlab code was developed to estimate the crystallite sizes and strain, and the linear regression analysis was used to compare all the models based on the coefficient of determination, where the Halder Wagner method gave the highest value (close to 1). Therefore, being the best candidate to fit the X-ray Diffraction data of metal-oxide nanoparticles. Advanced Rietveld was introduced for comparison purposes. Refined microstructural parameters were obtained from a nanostructured 40.5 nm Lanthanum hexaboride nanoparticles and correlated with the above estimation methods and transmission electron microscopy images. In addition, electron density modelling was also studied for final refined nanostructures, and μ-Raman spectra were recorded for each material estimating the mean crystallite size and comparing by means of a phonon confinement model.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

The tunable work function of titanium dioxide (TiO₂) nanoparticles of various sizes was measured using the Kelvin Probe Force Microscopy (KPFM) technique. The analysis of the contact potential difference (CPD) across TiO₂ nanoparticles of different sizes revealed a clear relationship between nanoparticle size, surface roughness, and work function. The study observed work function values ranging from 4.49 eV to 4.57 eV for particle sizes between 3 nm and 85 nm, which were higher than those of bulk TiO₂, likely due to quantum confinement effects. Additionally, electrostatic force microscopy (EFM) measurements showed significant charge-trapping behavior within TiO₂ nanoparticles under different applied bias voltages. The optical analysis also revealed a quantum confinement-induced band gap of 3.35 eV, larger than that of bulk TiO₂, and distinct photoluminescence peaks at 383 nm and 403 nm, corresponding to near-band-edge excitonic emissions and defect-related states. By analyzing the conduction band (CB) and valence band (VB) of TiO₂ nanoparticles using KPFM, the CB and VB positions were calculated based on work function data and bandgap. The results indicated that as particle size increases, both CB and VB energies shift slightly towards lower values, where smaller nanoparticles exhibit larger band gaps and higher work functions.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

High purity TiO2 and CuO powders were synthesized by the Pechini method, an inexpensive and easy-to-implement procedure to synthetize metal oxides. The variables of synthesis were the ethylene glycol:citric acid molar ratio and the pH. High reproducibility of the anatase and tenorite phase was obtained for all synthesis routes. The degree of purity of the powders was confirmed by XRD, FTIR, UV-vis absorption and XPS spectra. SEM and TEM images revealed the powders are composed by micrometer grains that can have a spherical shape (only in the TiO2) or formed by a non-compacted nanocrystalline conglomerate. FTIR spectra only vibrational modes associated to the TiO2 or CuO with a nanoparticle behavior. UV-vis absorption spectra revealed the values of maximum absorbance percentage of both systems are reached in the ultraviolet region, with percentages above 83 % throughout the entire visible light spectrum for the CuO system, a relevant result for solar cell applications. Finally, XPS experiments allow the observation of the valence bands and the calculation of the energy bands of all oxides.

In this paper, the phases in the Mg-Ti-O system using the 1:1 formulation of MgO:TiO2 mixing synthetic brucite of Mexican origin with TiO2 microparticles of high purity and with a heat treatment at 1100°C for 1 h were studied. The raw materials and formulation by XPS and DRX techniques were characterized. The results demonstrate the presence of different oxidation states in titania and the formation of different oxides in the Mg-Ti-O system when mixed and calcined at 1100°C; additionally, the formation of vacancies in the crystal lattice during the transformation from hexagonal brucite to magnesia with a cubic structure centered on the faces is estimated. With the results, its thermal behavior is warned based on the MgO-TiO2 phase diagram.

Mesoporous TiO2/reduced graphene oxide/Ag (TiO2/RGO/Ag) ternary nanocomposite with effective electrons transfer pathway is obtained by an electrostatic self-assembly method and photo-assisted treatment. Compared with bare mesoporous TiO2 (MT) and mesoporous TiO2/RGO (MTG), the ternary mesoporous TiO2/RGO/Ag (MTGA) nanocomposite exhibited superior photocatalytic performance for the degradation of MB under visible light, and the degradation rate reached 0.017 min-1, which was 3.4 times higher than that of MTG. It is proposed that Ag nanoparticles can form the local surface plasmon resonance (LSPR) to absorb the visible light and distract the electrons into MT, and RGO can accept the electrons from MT to accelerate the separation efficiency of carriers. The establishment of MTGA ternary nanocomposite make the three components act synergistic effect to enhance the photocatalytic performance.

Crystalline phase engineering is a prominent strategy for synergistically optimizing the sur-face-body phases of a catalyst. In this work, TiO2 nanosheets assembled into nanotubes (TNSTs) with two-phases of anatase and rutile were firstly synthesized via crystal engineering by simple thermal annealing, and subsequently loaded with Ru nanoparticles to create efficient benzene hydrogenation catalyst Ru/TNSTs. The well- designed nanosheet-tubes structure boasts large specific surface area and excellent transmission channels, which effectively prevents the ag-glomeration and deactivation of loaded Ru nanoparticles, as well as promotes the internal diffu-sion in the reaction process of benzene hydrogenation to cyclohexene. Furthermore, titanium dioxide nanosheet-tubes contain numerous Ti3+ defects, which not only improves the overall generation rate of cyclohexene, but also enhances the suppression of cyclohexene adsorption. Most importantly, the two-phases of titanium dioxide increases the ratio of the electron defi-ciencies of Ru and promotes cyclohexene desorption. These synergistic properties enhance the selectivity and efficiency of the Ru/TNSTs catalysts, resulting in excellent performance in the hydrogenation of benzene to cyclohexene. Especially the Ru/TNSTs-4 catalyst achieves a 95% in-itial selectivity and 51% yield of cyclohexene in the reaction, outperforming most supported Ru-based catalysts. This work may provide new perspectives for designing efficient benzene hydrogenation catalysts via crystalline phase engineering.

The utilization of titanium dioxide (TiO2) as a photocatalyst for the treatment of wastewater has attracted significant attention in the environmental field. Herein, we have prepared a NH2-MIL-125-derived TiO2@N-doped C Visible Light Catalyst through an in-situ calcination method. The nitrogen element in the organic connector is released through calcination, simul-taneously doping into the sample, thereby enhancing its spectral response to cover the visible region. The as-prepared TiO2@N-doped C catalyst exhibited preserved cage structure even after calcination, thereby alleviating the optical shielding effect and further augmenting its photo-catalytic performance by increasing the reaction sites between the catalyst and pollutants. The calcination time of the TiO2@N-doped C-450 °C catalyst was optimized to achieve a balance be-tween the TiO2 content and nitrogen doping level, ensuring efficient degradation rates for basic fuchsin (99.7%), Rhodamine B (89.9%), and tetracycline hydrochloride (93%) within 90 minutes.

The electron Transport layer (ETL) plays a crucial role in solar cell technology, particularly in perovskite solar cells (PSCs), where nanostructured TiO2 films have been investigated as superior ETL’s compared to compact TiO2. In this study we explore the nanocolumnal growth of TiO2 in the anatase phase, for bilayer thin films by magnetron sputtering (MS) technique and glancing angle deposition (GLAD). By optimizing the growth parameters, we achieved the formation of TiO2 nanocolumns with a cross-sectional diameter ranging from 50 to 75 nm. The average thickness of the films exceeded 12.71 ± 0.5µm , while the filaments exhibited an inclination angle close to 70◦ , corresponding to the deposition angle. Furthermore, we observed a correlation between the quality of the initial layer and enhanced growth of the TiO2 nanocolumns.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Indonesia is one of the largest banana producing countries in the world remaining abundance solid waste of banana fruit bunch. The banana fruit bunch contains high natural fibers which were obtained by an impregnation process using potassium hydroxide (KOH) and followed by a carbonization process under steam at 250°C for 5 h. The nanomaterial of TiO₂/fibre was prepared by a hydrothermal process at 200°C for 4 h. Surface morphology proved that the TiO₂ was loaded into the fibre by an increasing roughness of the surface and irregular size of porosity. The development of amorphous to crystalline phase of TiO₂/fibre was clearly observed. The effectiveness of TiO₂/fibre for removal of rhodamine B was investigated from different parameters of adsorptions in aqueous solution. The equilibrium adsorptions show that the Langmuir and Freundlich isotherm exhibited the best correlation coefficient (R² > 0.94) relating to the chemisorption and physisorption interaction in the adsorption process. Kinetic models were well described by the pseudo-first and second-order with the best correlation coefficient (R² > 0.99). These results indicate that nanomaterial TiO₂/fibre can be used as an effective adsorbent for removal of rhodamine B in aqueous solution.

In order to improve the strength of PVA/xylan composite films and endow them with ultraviolet (UV) shielding ability, TiO2-KH550 nanoparticle was synthesized and added into the PVA/xylan matrix. The TiO2-KH550 nanoparticle dispersed well in the 0.04% sodium hexametaphosphate (SHMP) solution under ultrasonic and stirring treatments. Investigations on the properties of films showed that TiO2-KH550 had the positive impact on improving the strength, moisture and oxygen barrier properties of the composite films. The maximum tensile strength (27.3 MPa), the minimum water vapor permeability (2.75×10-11 g•m-1•s-1•Pa-1) and oxygen permeability (4.013 cm3•m-2•24h-1•0.1MPa-1) were obtained under the addition of 1.5% TiO2-KH550. The tensile strength of TiO2-KH550 reinforced composite film was increased by 70% than that of the pure PVA/xylan composite film, and the water vapor and oxygen permeability were decreased by 31% and 41%, respectively. Moreover, the UV transmittance of film at the wavelength of 400 nm was almost zero when adding 1.5~2.5% of TiO2-KH550, which indicated the PVA/xylan composite films were endowed with excellent UV light shielding ability.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

The physiological characteristics of liquid digestate retrieved from various biogas plants based in northern Greece are presented. Preliminary photocatalysis experiments on inoculated liquid di-gestate sampled showed that disinfection is possible when pre-treated digestate with a combination of centrifuge-flocculation-μFiltration after 5.5 hours of 0.7g/L suspended TiO2 under UVA illumination for the experimental conditions is used. A novel design photocatalytic nanofiltration reactor was implemented for disinfection experiments on pre-treated liquid digestate, giving promising results. This work sets the basis for the efficient operation and engineering application of technology collaboration with photocatalysis as the final step for liquid digestate sanitation and reusable water recovery.

Wound infections evidently appeared in times of World War I that accounted a significant mortality and morbidity rate among injured soldiers. Currently, around 11 million people worldwide require medical treatment for wound infections and 300,000 die every year due to untreated wound infection. The extensive use of antibiotics to treat wound infection leads to emerging new microbial strains that are resistant to many antibiotics. There is a growing concern on the emergence and re-emergence of drug-resistant pathogens such as multi-resistant bacterial strains. Hence, the development of new antimicrobial compounds or the modification of those that already exist to improve antibacterial activity is a high priority area of research. During the past few decades, nanotechnology has arisen with new promising technology for synthesis of nanobiomaterials. Metallic nanoparticles (NPs) are considered as new alternative treatment with superior antibacterial activity. In this study, new formulation of titanium oxide (TiO2) NPs with different sizes were synthesized and characterized. Genotoxicity, mutagenicity and antibacterial activities of TiO2 NPs against the causative agents of wound infection were investigated. Antibacterial activity of TiO2 NPs was conducted against three ATCC ® bacterial strains: methicillin-resistant Staphylococcus aureus (MRSA), Escherichia coli and Pseudomonas aeruginosa. The results clearly illustrate a superior antibacterial activity of all newly formulated TiO2 NPs against the most causative agents of wound infection. Most of our TiO2 NPs showed non-genotoxic and non-mutagenic results at the maximum concentrations. Findings of this study will enhance the future of the therapeutic strategies against the resistant pathogenic strains that cause wound infections.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

Composites of Ag and TiO2 nanoparticles on cotton fabrics were synthetized in-situ by sono-chemical and hydrothermal methods achieving the successive formation of Ag-NPs and Ti-NPs directly on the fabric. The impregnated fabrics were characterized by ATR-FTIR spectroscopy, high resolution microscopy (HREM), scanning electron microscopy coupled with Ener-gy-dispersive X-ray spectroscopy (SEM-EDS), Raman, photoluminescence, UV-vis and DRS spectroscopies and by tension tests. Results showed the successful formation and impregnation of NPs on the cotton fabric, with a negligible leaching of NPs after several washing cycles. The photocatalytic activity of supported NPs was assessed by the degradation of methyl blue dye (MB) under solar and UV irradiation revealing improved photocatalytic activity of the Ag-TiO2/cotton composites due to a synergy of both Ag and TiO2 nanoparticles. This behavior is attributed to a diminished electron-hole recombination effect in the Ag-TiO2 cotton samples. The biocide activity of these composites on the growth inhibition of Staphylococcus aureus (Gram+) and Escherichia coli (Gram-) was confirmed, revealing interesting possibilities for the utilization of the functionalized cotton fabric as protective cloth for medical applications.

Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyses the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% of nano-TiO2 and compares it to the transparent base binder, and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier-Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity and exhibited values between the conventional binder and PMB regarding rutting resistance, penetration, and softening point. They showed similar behavior as the PMB, demonstrating signs of polymer-modification. The addition of TiO2 seems to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increases the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, considering fatigue and 10.0% concerning permanent deformation.

Since the photocatalytic reaction is a surface reaction, enhancing the gas movement around photocatalyst would promote photocatalytic CO₂ reduction performance. A new approach to enhance the gas movement around the photocatalyst by the natural thermosiphon movement of gasses around photocatalyst using black body material was proposed and confirmed experimentally, but the heat transfer mechanism on the phenomena was not clarified yet. The purpose of this study is to clarify the heat transfer mechanism of it. This study calculated the temperature of mixed gases of CO₂ and NH₃ around P₄O₁₀/TiO₂ photocatalyst by the heat transfer formula. It is revealed that there was no difference between the increase temperature (T_g) from the temperature at the beginning of the CO₂ reduction experiment (T_ini) and the temperature of mixed gases of CO₂ and NH₃ measured by thermocouple in the experiment (T_e) under the illumination condition with a visible light (VIS) + an infrared light (IR) and IR only. The heat transfer model proposed by this study has predicted T_g well under the illumination condition with VIS + IR and IR only well. On the other hand, it is revealed that the difference between T_g and T_e was as large as 10 ℃ under the illumination condition with an ultra violet light (UV) + VIS + IR.

The present study sought to determine the effect of incorporating a Chitosan-TiO2 nano-composite on the color stability of pigmented Room Temperature Vulcanization (RTV) maxillofacial silicone subjected to a variety of accelerated aging conditions. The experimental setup consisted of one hundred groups of five disk-shaped specimens (22mm diameter, 2mm thick) each, created using RTV silicon elastomer type A-2186, with the total sample distributed into four groups based on the pigments combined with the silicon—specifically, brilliant red, blue, and yellow dry intrinsic pigments (at 0.2% concentration by weight) and a fourth group that remained non-pigmented. Each of these primary groups was further subdivided into five categories corresponding to the silicon variants treated with different nanoparticles—2% TiO2, 3% Chitosan, a hybrid nano-combination of 1% TiO2/Chitosan, 1% synthesized Chitosan-TiO2 Nanocomposite, and a control group devoid of nanoparticle additions. The synthesized Chitosan-TiO2 Nanocomposite was effectively prepared using the core-shell method. The color stability of each silicon category, irrespective of whether pigmented or non-pigmented was evaluated by calculating the color difference (ΔE) pre- and post-subjection to five distinct accelerated aging conditions: 30 hours in an antibacterial cleaning solution, six months in sebum, six months in sweat, UV-accelerated aging for 720 hours, and outdoor weathering for six months. Color measurements were taken using a Colorimeter within the CIELAB color system. Statistical analyses, including one-way ANOVA at a significance level of p < 0.05, were employed to discern significant differences among the various accelerated aging conditions across the five silicon categories. Further comparisons were made using Dennett's T3 multiple comparison test, Tukey HSD multiple comparisons, and a t-test, with SPSS for Windows version 27.0 as the software platform. Results indicated that all silicon types, whether pigmented or not, exhibited varying degrees of color change under different aging conditions. Red-colored samples, across all silicon categories, demonstrated significant color alterations after 720 hours of UV-accelerated aging, with the most pronounced change in the 3% Chitosan samples and the least in the 2% TiO2 samples. Six months of outdoor weathering led to a marked increase in ΔE values across all categories. The blue-pigmented silicon samples treated with 2% TiO2 showed the highest color modification, while the yellow-pigmented silicon and non-pigmented silicon also underwent significant color shifts, particularly in the control and Chitosan-TiO2 categories, respectively. The study underscores the pervasive influence of outdoor weathering on color stability across all silicon categories. It also demonstrates that while nanoparticle incorporation offers some resilience against accelerated aging, it fails to provide adequate protection against the specific effects of UV radiation encountered during outdoor weathering.

The study aims to elaborate a neural model and algorithm for optimising hardness and porosity of coatings and thus ensure that they have superior cavitation erosion resistance. Al2O3-13wt.%TiO2 ceramic coatings were deposited onto 316L stainless steel by atmospheric plasma spray (ASP). The coatings were prepared with different values of two spray process parameters: the stand-off distance and torch velocity. Microstructure, porosity and microhardness of the coatings were examined. Cavitation erosion tests were conducted in compliance with the ASTM G32 standard. Artificial neural networks (ANN) were employed to elaborate the model, and the multi-objectives genetic algorithm (MOGA) was used to optimise both properties and cavitation erosion resistance of the coatings. Results were analysed with Matlab software by Neural Network Toolbox and Global Optimization Toolbox. The fusion of artificial intelligence methods (ANN+MOGA) is essential for future selection of thermal spray process parameters, especially for the design of ceramic coatings with specified functional properties. Selection of these parameters is a multicriteria decision problem. The proposed method made it possible to find a Pareto front, i.e. trade-offs between several conflicting objectives – maximising the hardness and cavitation erosion resistance of Al2O3-13%TiO2 coatings and, at the same time, minimizing their porosity.

One of the most important objectives of the studies worldwide is to improve the performance of automotive engines to reduce fuel consumption and environmental pollution. Accordingly, the principal motivation of this research study is improving the tribological behavior of the piston ring/cylinder liner interfaces as a promising and straightforward approach in automotive fuel economy and increasing engine durability using Al₂O₃ and TiO₂ nanomaterials as smart nano-lubricant additives that adapted to different operating conditions by replenishing mechanisms anti-friction and anti-wear in automotive engines.

The effect of Localized Surface Plasmon (LSP) of 5 nm mean size Au particles deposited on TiO2 P25 was investigated during the photo-thermal water gas shift reaction (WGSR). The effects of CO concentration, excitation light flux and energy, and molecular oxygen addition during the reaction were investigated. The photocatalytic WGSR rate under light excitation with wavelengths extending from 320 to 1100 nm was found to be higher than the thermal reaction alone at the same temperature (85 oC). A ratio H2/CO2 of near unity was found at high concentrations of CO. Addition of molecular oxygen during the reaction resulted in a slight decrease of molecular hydrogen production while the rates of CO2 formation and that of CO consumption changed by one order of magnitude. More important, it was found that the WGSR rates were still high under only visible light excitation (600 - 700 nm). The results prove that Au LSP alone triggers this chemical reaction without the need to excite the semiconductor on which they are deposited.

This review focuses on Cu/TiO2 sequentially and Cu-TiO2 co-sputtered catalytic/photocatalytic surfaces leading to bacterial inactivation discussing their stability, synthesis, adhesion and antibacterial kinetics. The intervention of TiO2, Cu and the synergic effect of Cu and TiO2 on films prepared by a colloidal approach and other techniques is also reviewed leading to bacterial inactivation. Processes in aerobic media and anaerobic media leading to bacterial loss of viability on multidrug resistant (MDR) pathogens, Gram-negative (-) and Gram-positive(+) bacteria are described. Insight is provided for the interfacial charge transfer mechanism under solar irradiation occurring between TiO2 and Cu. surface properties of 2D TiO2/Cu and TiO2-Cu films are correlated with the bacterial inactivation kinetics observed in the dark and under light. The intervention of these antibacterial sputtered surfaces in health-care facilities leading to MRSA-isolates is described in the dark and under the actinic light. The synergic intervention of the Cu and TiO2 films leading to bacterial inactivation prepared by direct current magnetron sputtering (DCMS), pulsed direct current magnetron sputtering (DCMSP) and highly ionized pulse plasma magnetron sputtering (HIPIMS) is reported in a detailed way.

Mercury (Hg) is a toxic element impacting on biological systems and ecosystems. Because the toxicity of Hg species is highly dependent on concentration levels and chemical forms, sensitive identification of chemical forms for Hg, i.e., Hg speciation, is of major significance in providing meaningful information about the source of Hg exposure. In this study, a microfluidic-based device made of high clarity poly(methyl methacrylate) (PMMA) was fabricated. Then titanium dioxide nanoparticles (nano-TiO2) were attached to the treated channel interior with the aid of poly(diallyldimethylammonium chloride) (PDADMAC). After coupling the nano-TiO2-coated microfluidic-based photocatalyst-assisted reduction device (the nano-TiO2-coated microfluid-ic-based PCARD) with high-performance liquid chromatography (HPLC) and inductively coupled plasma-mass spectrometry (ICP-MS), a selective and sensitive hyphenated system for Hg specia-tion was established. Validation procedures demonstrated that the method could be satisfactorily applied to the determination of mercuric ion (Hg2+) and methylmercury ion (CH3Hg+) in both human urine and water samples. Remarkably, the zeta potential measured clearly indicated the PDADMAC-capped nano-TiO2 with predominance of positive charges indeed provided steady force for firm attachment to the negatively charged device channel. The cause for the durability of the nano-TiO2-coated microfluidic-based PCARD was clarified thus.

Many stable water dispersions of various chemical compositions containing bioactive chemical compounds: copper silicate, titanium dioxide and zinc oxide (and other auxiliary substances) were developed and fabricated - they were used for preparation of thin hybrid coatings having very good antimicrobial properties against gram negative bacteria (Escherichia coli), gram positive bacteria (Staphylococcus aureus) and yeast fungus (Candida albicans). Polyester (PES) nonwovens were modified by dip-coating, and PES and cotton fabrics - by dip-coating and coating methods.