In view of the limitations of the existing optimization method of suspender cable force, in order to improve the stress of suspender under completion state and avoid frequent adjustment of cable force and grid beam elevation during construction, a new method of cable force optimization is proposed. The article takes the longest large span arch bridge in the world, Pingnan Third Bridge, a Concrete-filled steel tube (CFST) arch bridge with a span of 575m as the engineering background combined with the finite element analysis and multi-objective optimization method. One cable force optimization method that suspender “Real-time correction during construction, in the process variable optimal and results reliable” during panel girder lifting of long span CFST arch bridges is clarified. Taking the panel girder weight and displacement during the construction as parameter variables, the displacement and unevenness of the panel girder under completion state as constraint conditions, the displacement and cable force during the hoisting construction as the objective equation, through the optimization of the objective equation, the suspender cable force and dis-placement of each hoisting section are calculated. The results show that it is feasible to introduce the optimization theory into the cable force optimization when lifting the panel girder. the segment displacement variation is minimized to meet the destination. The cable force distributed evenly under completion state of the bridge that further making sure the completion state satisfies the requirements. No repeating iteration is needed, thus avoiding cumberso me calculation, getting cable force once. With higher optimization efficiency and better effects, the method provides high value for the cable force calculation of same type bridge suspender construction and for guiding construction.

The reason for excessive multidecade deflections is still unclear after 70 years of the cantilever method that has been applied in building large-span segmental concrete bridges. The failure of the Koror-Babeldaob bridge gives the author a clue that the reason might be the boundary condition. The asymmetric properties of the bearing and prestress tendon draw the author’s attention. To understand the process of stress redistribution, the virtual stiffness method which is derived from the principle of minimum potential energy was created, and the phenomenon the author suggested named Material Inelasticity and Prestress Loss Coupling Effect is discovered. The unexplainable excessive deflection and prestress loss are found in the new load model. The calculation of excessive deflection is discussed. The new model fits the experience well. The optimization design methods and construction key points are proposed.

Steel damper columns (SDCs) are energy-dissipating members that are suitable for reinforced concrete (RC) moment-resisting frames (MRFs) and those often used for multistory housing. In a previous study, an energy-based prediction procedure for the peak and cumulative response of an RC frame building with SDCs was proposed. In this procedure, the accuracy of the equivalent velocity of the maximum momentary input energy (V_ΔE1^*)–peak equivalent displacement (D₁^*_max) relationship is essential for improved prediction. In this article, the seismic capacity curve (V_ΔE1^*–D₁^*_max relationship) of RC MRFs with and without SDCs is evaluated using incremental critical pseudo-multi impulse analysis (ICPMIA). In the ICPMIA, which is based on a study by Takewaki and coauthors, the structure is subjected to various intensities of critical pseudo-multi impulsive lateral force. An ICPMIA of four 8- and 16-story RC MRFs with and without SDCs is performed to obtain their structural behaviors under various intensities of pulsive input. Then, the seismic capacity curve obtained from the ICMPIA results are compared with the predicted results based on the simplified equations. The main findings of this article are as follows. (i) The seismic capacity curve of RC MRFs without SDCs strongly depends on the number of impulsive lateral forces (N_p). As N_p increases, the seismic capacity decreases. The predicted seismic capacity curve severely underestimates that obtained from the ICMPIA in the case of large N_p. This trend is notable when the level of pinching behavior in the RC members is severe. (ii) In the case of an RC MRF with SDCs, however, the influence of N_p on its seismic capacity curve is small. The predicted seismic capacity curve agrees very well with that obtained from the ICMPIA. The influence of the level of pinching behavior in RC members on the seismic capacity curve is small.

Three-dimensional (3D) printing technologies are transforming the design and manufacture of components and products across a variety of disciplines, however their application in the construction industry is still limited. Material deposition processes can achieve infinite geometries and have advanced from rapid prototyping and model-scale markets to their application in fabricating functional products, large objects and the construction of full-scale buildings. Many international projects have recently been realized and the construction industry is beginning to utilise these dynamic technologies. The potential advantages for integrating 3D printing into house construction are significant, these include the capacity for mass customization of designs and parameters for functional and aesthetic purposes, reduction in construction waste from highly precise material placement, and the use of recycled waste products in layer deposition materials. With the ultimate goal of improving construction efficiency and decreasing building costs, applying Strand7 Finite Element Analysis software, a numerical model was designed specifically for 3D printing in a cement mix incorporated with recycled waste product High Density Polyethylene (HDPE) and found that construction of an arched truss-like roof was structurally feasible without the need for steel reinforcements. The lab sizes prototypes were manufactured based on the destined numerical model by using a 3D printing technology. Currently available 3D printing technologies can be adopted for building construction and this paper discusses the applications, advantages, limitations and future directions of 3D printing as an innovative and viable solution for affordable house construction.

The area of Central and Eastern Europe, and thus Poland, is not exposed to effects of seismic actions. Any possible tremors can be caused by coal or copper mining. Wind, rheological effects, the impact of other objects or a non-uniform substrate are the predominant types of loading included in calculations for stiffening walls. The majority of buildings in Poland, as in most other European countries, are low, medium-high brick buildings. Some traditional materials, like solid brick (>10% of construction materials market) are still used. But autoclaved aerated concrete (AAC) and cement-sand calcium-silicate (Ca-Si) elements with thin joints are prevailing (>70% of the market) on the Polish market. Adding reinforcement only to bed joints in a wall is a satisfactory solution (in addition to confining) for seismic actions occurring in Poland that improves ULS and SLS. This paper presents results from our own tests on testing horizontal shear walls without reinforcement and with different types of reinforcement. This discussion includes 51 walls made of solid brick (CB) reinforced with steel bars and steel trusses, results from tests on 15 walls made of calcium-silicate (Ca-Si) and AAC masonry units reinforced with steel trusses and plastic meshes. Taking into account our own tests and those conducted by other authors, empirical relationships were determined on the basis of more than 90 walls. They are applicable to design and construction phase to determine the likely effect of reinforcement on cracking stress that damage shear deformation and wall stiffness.