DSSC devices are among the most widely studied thin-film solar cells because of their cost-effectiveness, low toxicity, and simple fabrication method. However, there is still much scope for replacing current DSSC materials due to their high cost, low volume, and lack of long-term stability. Accordingly, ITO-nanorod films were fabricated by E-beam evaporation using the glancing angle deposition method in this study. Then, the ITO-nanorod was treated by oxygen plasma via a bias-magnetron RF sputtering process to improve the efficiency of DSSC under a varying gas flow rate of 20, 40, 60, 80, and 100 sccm. The FE-SEM investigation of the ITO film structure revealed that the obtained nanorod structures have slightly different diameters. At the same time, an increase in the oxygen flow rate resulted in a rougher film surface structure. In this, the lower sheet resistance was received because of rougher morphology. When comparing the DSSC efficiency test results, we found that at a gas flow rate of 100 sccm, the highest efficiency value showed by 9.5%. On the other hand, the ITO-nanorod without plasma treatment exhibited the lowest efficiency. Hence, plasma technology can be practically applied to improve the efficiency of DSSC devices. This study will be a prototype of a highly advanced solar cell manufacturing method for the solar cell industry.

Immunoglobulin G (IgG), a type of antibody, represents approximately 75% of serum antibodies in humans, and is the most common type of antibody found in blood circulation Consequently, the development of simple, fast and reliable systems for IgG detection are of considerable interest which can be achieved using electrochemical sandwich-type immunosensors. In this study we have developed an immunosensor sub-strate using an inexpensive and very simple fabrication method based on ZnO nanorods obtained through the electrodeposition of ZnO. The ZnO nanorods were treated by electrodepositing a layer of reduced gra-phene oxide to ensure an easy immobilization of the antibodies. On this substrate, the sandwich configura-tion of the immunosensor was built through different incubation steps, that were all optimized. The im-munosensor is electrochemically active thanks to the presence of gold nanoparticles tagging the secondary antibody, therefore it has been used to measure the current density of the hydrogen development reaction which is indirectly linked to the concentration of H-IgG antigens. In this way the calibration curve was constructed obtaining a linear range of 1-100 ng / ml with a detection limit of few ng / mL and good sensi-tivity.

CoO-ZnO-based composites have attracted considerable attention for the development of energy storage devices because of their multifunctional characterization and ease of integration with existing components. This paper reports the synthesis of CoO@ZnO (CZ) nanostructures on Ni foam by the CBD method for facile and eco-friendly supercapacitor applications. The formation of a CoO@ZnO electrode functioned with cobalt, zinc, nickel and oxygen groups was confirmed by X-ray diffraction, X-ray photoelectron spectroscopy, low and high-resolution of scanning electron microscopy, and transmission electron microscopy. The as-synthesized hierarchical nanocorn skeleton-like structure of CoO@ZnO-3h (CZ3h) electrode delivered a higher specific capacitance of 1136 F/g at a current density of 3 A/g with outstanding cycling stability, showing 98.3% capacitance retention over 3000 cycles in an aqueous 2 M KOH electrolyte solution. This retention was significantly better than that of other prepared electrodes, such as CoO (CO), ZnO (ZO), CoO@ZnO-1h (CZ1h), and CoO@ZnO-7h (CZ7h) (274, 383, 240 and 537 F/g, respectively). This superior capacitance was attributed to the ideal surface morphology of CZ3h, which is responsible for the rapid electron/ion transfer between the electrolyte and electrode surface area. The enhanced features of the CZ3h electrode highlight potential applications in high performance supercapacitors, solar cells, photocatalysis, and electrocatalysis.

This paper proposes a theoretical silicon dioxide (SiO2) solar cell based dielectric metamaterial unit surface consisting of zinc oxide (ZnO) periodic nanorods of bandgap energy of 2.2-2.4eV. It evaluates the absorptive efficiency of the film using S-parameter and Z-parameter testing of magnitude, return/insertion loss, and impedance matching with respect to a frequency band of 0.0014-10.5THz. Terahertz applications of the result are considered due to potential scope for infrared (IR) and microwave (MW) spectral selectivity with ZnO. Calculations of input n-impedance and loss tangents are also presented with emphasis on the exhibition of antireflection to gauge the performance of the thin-film meta-surface in tandem solar cells. The data for the reflectance parameters of this structure, primarily the S11 loss and impedance matching (dB/dB10) are compared to those of prior investigations with different metamaterial coatings on SiO2 solar photovoltaic cells, as well as ZnO nanorods used in photovoltaic applications, to ascertain the cylindrical meta-surface structure with the preset thicknesses of the study being an effective anti-reflector. Application can be extended to other broadband domains requiring plasmonic graded refractive surfaces, in further work.