Afghanistan is overwhelmed with food insecurity that is a large percentage of the population lacks reliable access to food supplies. Grains play a vital role in the country's food security due to their importance in terms of consumption and production quantity. This paper estimates cereal self-sufficiency and then makes a food balance forecast of the three major food crops cultivated in Afghanistan over six-decades. Descriptive statistics and coarse metric techniques were employed to determine cereal self-sufficiency and food balance forecast. The econometric analysis demonstrated that (1) Afghanistan is not yet self-sufficient in meeting grain consumption, and the production and consumption ratio declined from 0.9 to 0.55 from 1979 to 2030. (2) The gap of theoretical food imbalance will increase, and by the year 2030, cereal production will likely be sufficient for only 49.8 percentage of inhabitants, leaving a high shortage equivalent to the amount required by 24.4 million people. By evaluating the quantitative food balance and the growing population change, this study presents an analysis of the emerging threat to Afghanistan's food security and suggests a solution for food security, should increase the size of public agricultural expenditure, improve the level of agriculture infrastructure, and continue to introduce a policy to achieve higher yield.

Modern day construction is widely influenced using concrete-steel composite columns. A lot of research on concrete-steel composite columns is being carried out around the world. The rapid growth in concrete-steel composite construction has widely decreased the use of conventional reinforced cement concrete construction (R.C.C), and the steel construction practices. The concrete-steel composite construction has obtained an extensive receiving around the globe. As Pakistan is a developing country, so, it is relatively a new concept for its construction industry when compared with the developed countries around the globe. Although, the R.C.C construction is suitable and economical for construction of framing systems of low-rise buildings, however, the increased dead load, span restrictions, less stiffness and risky formwork makes it uneconomical and unviable when it comes across the construction of intermediate to high-rise buildings. This research is an effort to learn the cost effectiveness, increased or decreased stiffness, and change on the functionality of the composite construction for intermediate to high-rise buildings constructed in Pakistan. A Base + Ground + 11 storey commercial building is selected for this study. A comparison is made between conventional R.C.C columns structure and concrete-encased composite columns structure. The equivalent static nonlinear analysis is performed using ETABS 2017 software. Although, for Base + Ground + 11 storey building, the construction cost of concrete-encased composite structure is 7.7% more than the conventional R.C.C columns structure, but the concrete-encased composite structure will have 13.013% more constructed floor area. This increased floor area helps to settle the cost difference between the two structures.

Mathematical literacy is a very hot issue in the development of mathematics learning, apart from mathematical literacy, another interesting thing is the entrepreneurial spirit that must be given from an early age, especially for vocational students. This research was conducted at SMK Rosma Karawang in the Department of Computer and Network Engineering, West Java Province with the XI grade students. The teaching materials developed by applying the principles of the development model developed with the ADDIE model consist of analysis, design, development, implementation and evaluation. This research and development model is considered suitable for developing teaching tools and materials which is used for the purposes of the learning process. Based on the results of data analysis and processing that have been carried out in this study, the development of teaching materials using the ADDIE model has met the appropriate and valid criteria by media, language and media expert valuators. Another result of developing this teaching material besides meeting the eligibility criteria is that the teaching materials developed are able to increase mathematical literacy and instill entrepreneurial spirit for students.

Astringency is an important sensory characteristic of food and beverages containing polyphenols. However, astringency perception in elderly people has not been documented. The aim of the present work was to evaluate sensitivity to astringency as a function of age and salivary flow. Fifty-four panellists, including 30 elderly people (age=75±4.2 years) and 24 young people (age=29.4±3.8 years), participated in this study. Astringency sensitivity was evaluated by the 2-alternative forced choice (2-AFC) procedure using tannic acid solutions. Whole saliva was collected for 5 min before and after sensory tests. The results showed that the astringency threshold was significantly higher in the elderly group than in the young group. Moreover, a negative correlation between salivary flow and threshold was observed in the young group only. These results showed a difference in oral astringency perception as a function of age for the first time. This difference can be linked to salivary properties that differ as a function of age.

Since the launch of Protein Data Bank (PDB) in 1971, Cartesian coordinate system (CCS) has been the default approach to specify atomic positions in biomolecular experimental structures with X, Y and Z. In 2020, a local spherical coordinate system (LSCS) approach was proposed as an alternative to CCS, i.e., ρ, θ and φ. Recently, the continued application of deep learning technology in protein structure prediction (PSP) saw a leap forward in the accuracy of PSP, as evidenced by AlphaFold of Google’s DeepMind. However, there still is room for the improvement of the performances of PSP algorithms to date. Given that geometrically, CCS and LSCS are like the two sides of a coin, this short article puts forward a hypothesis that the time is now ripe to end the half-a-century burial of ρ, θ and φ in PDB, and use them as LSCS features for the design of novel PSP algorithms in future.

Different machine learning models (multiple linear regression, vector support machines, artificial neural networks and random forests) are applied to predict the monthly global irradiation (MGI) from different input variables (latitude, longitude and altitude of meteorological station, month, average temperatures, among others) of different areas of Galicia (Spain). The models were trained, validated and queried using data from three stations, and each best machine model was checked in two independent stations. The results obtained confirmed that the best ML methodology is the ANN model which presents the lowest RMSE value in the validation and querying phases 122.6·10kJ/(m2∙day) and 113.6·10kJ/(m2∙day), respectively, and predict conveniently for independent stations, 201.3·10kJ/(m2∙day) and 209.4·10kJ/(m2∙day), respectively. Given the good results obtained, it is convenient to continue with the design of artificial neural networks applied to the analysis of monthly global irradiation.

Within the framework of multiblock data analysis, a unified approach of supervised methods is discussed. It encompasses multiblock redundancy analysis (MB-RA) and multiblock partial least squares (MB-PLS) regression. Moreover, we develop new supervised strategies of multiblock data analysis, which can be seen as variants of one or the other of these two methods. They are respectively refered to as multiblock weighted redundancy analysis (MB-WRA) and multiblock weighted covariate analysis (MB-WCov). The four methods are based on the determination of latent variables associated with the various blocks of variables. They are derived from clear optimization criteria whose aim is to maximize either the sum of the covariances or the sum of squared covariances between the latent variable associated with the response block of variables and the block latent variables associated with the various explanatory blocks of variables. We also propose indices to help better interpreting the outcomes of the analyses. The methods are illustrated and compared based on simulated and real datasets.

On estimation scales ranging from 0.1 nm to 100 nm, the nanoscale is part of the capacitance components of the physical-synthetic and natural environment. Dimensionality, morphology, structure, uniformity, and agglomeration are all used to classify nanoparticles. Its functionality and effect on the environment and species are influenced by its shape and morphology. The priority research is to determine the effects of nanoparticles on any biological entity that is necessary when designing nanotechnology-based biotechnological and biomedical products. Bacteria have a remarkable ability to reduce metal ions, making them one of the most promising candidates for nanoparticle biosynthesis. Nanoparticles have been researched in the biomedical field for antimicrobial, biosensor, diagnostic imaging, and drug delivery applications. These natural technologies appear to be capable of producing stable nanoparticles with well-defined dimensions, morphologies, and compositions by optimizing reaction conditions and selecting the best bacteria. This work includes a list of the most commonly used microorganisms and associated Nanoparticles, as well as a discussion of current biotechnology and biomedical developments.

In the past decades, regenerative medicine applied on skin lesions has been a field of constant improvement for both human and veterinary medicine. The process of healing cutaneous wound injuries implicates a well-organized cascade of molecular and biological processes. However, sometimes the normal process fails and can result in a chronic lesion. In addition, wounds are considered an increasing clinical impairment, due to the progressive ageing of the population, as well as the prevalence of concomitant diseases, such as diabetes and obesity, that represent risk aggravating factors for the development of chronic skin lesions. Stem cells regenerative potential has been recognized worldwide, including towards skin lesion repair, Tissue engineering techniques have long been successfully associated with stem cell therapies, namely the application of 3D bioprinted scaffolds. With this review we intend to explore several stem cell sources with promising aptitude towards skin regeneration, as well as different techniques used to deliver those cells and provide a supporting extracellular matrix environment, with effective outcomes. Furthermore, different studies are discussed, both in vitro and in vivo, towards their relevance in the skin regeneration field.

Living organisms with developed endocrine systems react in a complex way to environmental changes. Changing atmospheric pressure causes different blood pressures or hormone levels; carcinogenic radiation modifies the structure of DNA. Charged particles and ions act as neurotransmitters and block certain types of protein channels and receptors. A high concentration of carbon dioxide has an indirect effect on both blood pressure and neuron activity. The bioelectric nature of living tissues highlights the complexity of the connection between the dynamic physical environment and biological systems. Recent results from studies on the interactions and connections mentioned above are reviewed in this paper.

The inaccurate estimates of linear prediction coefficient (LPC) and noise variance introduce bias in Kalman filter (KF) gain and degrades speech enhancement performance. The existing methods proposed a tuning of the biased Kalman gain particularly in stationary noise condition. This paper introduces a tuning of the KF gain for speech enhancement in real-life noise conditions. First, we estimate noise from each noisy speech frame using a speech presence probability (SPP) method to compute the noise variance. Then construct a whitening filter (with its coefficients computed from the estimated noise) and employed to the noisy speech, yielding a pre-whitened speech, from where the speech LPC parameters are computed. Then construct KF with the estimated parameters, where the robustness metric offsets the bias in Kalman gain during speech absence to that of the sensitivity metric during speech presence to achieve better noise reduction. Where the noise variance and the speech model parameters are adopted as a speech activity detector. The reduced-biased Kalman gain enables the KF to minimize the noise effect significantly, yielding the enhanced speech. Objective and subjective scores on NOIZEUS corpus demonstrates that the enhanced speech produced by the proposed method exhibits higher quality and intelligibility than some benchmark methods.

Olfactory ensheathing cells (OECs) are the glial cells that accompany axons from the olfactory epithelium to their targets in the olfactory bulb. They possess unique features that have made them the subject of much study as being potentially useful in cell-based therapeutic approaches to CNS repair. Investigation of OECs has demonstrated antigenic and morphological heterogeneity in their population. No marker specific to and selective for OECs have yet been identified, and many of the markers used are variably expressed by other glial cells. Even among OECs, these markers appear to vary in vivo (depending on their anatomical location, contact with other cells, and developmental timing) and in vitro. The variation across the population of OECs has compromised their isolation and characterization. It has also made the task of identifying meaningful subpopulations - with greater or lesser therapeutic utility - dependent on identifying the source of their variability. Such information would aid in both the harvest and experimental manipulation of OECs to optimize their therapeutic effect. One way to understand the nature of this variability is to seek its potential causes in vivo. This must begin with an examination of the structure of the olfactory nerve. Here, the structure and development of the primary olfactory projection are thoroughly reviewed with an emphasis on OECs and the cells with which they make contact. The relevant experimental results are also discussed. The weight of anatomical evidence indicates that the structural variations described in different locations and across species are mostly the result of spatiotemporal developmental factors. As such, the formation of the olfactory projection is mediated primarily by the source tissue, the olfactory epithelium. Cell-autonomous development is common elsewhere, and suits the evolutionary age and importance of olfaction, as well as its continued regenerative capacity. Our findings provide a more systematic anatomical understanding of this nerve. That understanding indicates that variation in axon ensheathment by OECs is an inherent feature arising from the flexibility of the ensheathing program. This perspective, along with the anatomical data reviewed here, can inform more carefully controlled laboratory investigations designed to uncover the detailed mechanisms governing OEC biology.

Nanotechnology is an emerging field of modern science based on the use of nanoparticles (NPs) with a huge potential in many sectors, including nanomedicine. Their small size confers them unique properties because they are subject to physical laws that are in the middle between classical and quantum physics. In this context, NPs project plays a pivotal role because the composition, size, shape and surface proprieties need to be carefully considered for their optimal design and application. As reported in this review, NPs are classified in inorganic (metallic NPs; quantum dots; carbon-based nanostructures; mesoporous silica nanoparticles) and organic (liposomes and micelles, dendrimers and polymer nanoparticles) ones. Here, we report an accurate description of the potential of each NPs type focusing on their multiple areas of application like theranostics drug delivery, imaging, tissue engineering, antimicrobial techniques and nanovaccines, and therefore they represent a promise to revolutionize the new era of nanomedicine, especially in cancer research.

This paper aims to provide an overall review of degradation, damage evolution and fatigue models in the literature of various engineering materials, mostly metals, and composites.

In recent years, many researchers have begun to shift their focus onto the synthesis of nanomaterials as this field possesses immense potential that may provide incredible technological advances in the near future. The downside of conventional synthesis techniques, such as co-precipitation, sol-gel and hydrothermal methods, is that they necessitate the use of toxic chemicals, produce harmful by-products and require a considerable amount of energy; therefore, more sustainable fabrication routes are sought after. Biological molecules have been previously utilised as precursors to nanoparticle synthesis, thus eliminating the negative factors involved in traditional methods. In addition, transition-metal nanoparticles possess a wide scope of applications due to their multiple oxidation states and large surface areas; thereby allowing for a higher reactivity when compared to their bulk counterpart and rendering them an interesting research topic. However, this field is still relatively unknown and unpredictable. Therefore, this review aims to obtain a better understanding on the plant-mediated synthesis process of the major transition-metal and transition-metal oxide nanoparticles, and how different parameters affect their unique properties.

Burnout is common in many countries and is associated with several other problems, such as depression, anxiety, insomnia and memory deficits, and prospectively it predicts long-term sick-leave, cardiovascular disease and death. Clinical burnout or its residual symptoms often last several years and a common assumption is that recovery takes a long time by nature despite full time sick-leave and absence of work stress. Literature suggests models that hypothetically explain the development, but not maintenance, of the syndrome. Based on cognitive and behavioral principles and stress theory this paper describes a theoretical model explaining how clinical burnout can develop and be maintained. While the development of clinical burnout is mainly explained by prolonged stress reactions and disturbed recovery processes due to work related stressors, maintenance of the syndrome is particularly explained by prolonged stress reactions and disturbed recovery processes due to the new context of experiencing burnout and being on sick-leave. Worry about acquired memory deficits, passivity and excessive sleep, shame, fear of stress reactions, and the perception of not being safe are examples of responses that can contribute to the maintenance. The model has important implications for research and how to intervene clinical burnout.

The Evolutionary history and domestication of Camels are largely unexplored because of the lack of well dated early archaeological records. However, limited records suggest that domestication of Camels likely happened in the late second millennium BCE. Over the time, camels have helped human for their basic needs like meat, milk, wool, dung to long routes transportation. This multifaceted animal has helped the mankind to connect through continents and in trade majorly through the Silk route. In India, both dromedary and Bactrian camels are found and their habitat is entirely different from each other, dromedaries inhabit in hot deserts and Bactrians are found mostly in cold places (Nubra Valley, Ladakh). Fewer studies on Indian dromedaries have been conducted but no such studies are done on Bactrian camels. It is needed to study the genetics of Bactrian camels to find out their genetic affinity and evolutionary history with other Bactrians found in different parts of the world. Furthermore, parallel studies on humans and Bactrian camel are required to understand the co-evolution and migration pattern of humans during their dispersal in different time periods.

In a large variety of organisms, antimicrobial peptides (AMPs) are primary defences against pathogens. BP100 (KKLFKKILKYL-NH2), a short, synthetic, and cationic AMP, is active against bacteria and displays low toxicity towards eukaryotic cells. BP100 acquires an α-helical conformation upon interaction with membranes and increases membrane permeability. Despite the volume of information available, the mechanism of action of BP100, the selectivity of its biological effects, and its applications are far from consensual. In this work, we synthesized a fluorescent BP100 analog containing naphthalimide linked to its N-terminal end, Napht-BP100 (Napht-AAKKLFKKILKYL-NH2). The fluorescence properties of naphthalimides, especially their spectral sensitivity to microenvironment changes, are well established, and their biological activities against different types of cells are known. A wide variety of techniques were used to demonstrate that a-helical Napht-BP100 was bound and permeabilized POPC and POPG LUV. Napht-BP100, different from that observed for BP100, was bound to, and permeabilized POPC LUV. With zwitterionic (POPC) and negatively charged (POPG) containing LUVs, membrane surface high peptide/lipid ratios triggered complete disruption of the liposomes in a detergent-like manner. This disruption was driven by charge neutralization, lipid aggregation, and membrane destabilization. Napht-BP100 also interacted with double-stranded DNA, indicating that this peptide could also affect other cellular processes in addition to membrane destabilization. Napht-BP100 showed superior antibacterial activity, increased hemolytic activity compared to BP100, and may constitute an efficient antimicrobial agent for dermatological use. By conjugating BP100 and naphthalimide antimicrobial properties, Napht-BP100 was bound more efficiently to the bacterial membrane and could destabilize the membrane and enter the cell by interacting with its cytoplasm- exposed DNA.

This paper presents a framework for the motion planning and control of redundant manipulators with the added task of collision avoidance. The algorithms that were previously studied and tested by the authors for planar cases are here extended to full mobility redundant manipulators operating in a three-dimensional workspace. The control strategy consists of a combination of off-line path planning algorithms with on-line motion control. The path planning algorithm is used to generate trajectories able to avoid fixed obstacles, detected before the robot starts to move; it is based on the potential fields method combined with a smoothing interpolation that exploits Bézier curves. The on-line motion control is designed to compensate for the motion of the obstacles and to avoid collisions along the kinematic chain of the manipulator; it is realized by means of a velocity control law based on the null space method for redundancy control. A term of the control law takes into account the speed of the obstacles as well as their position. In order to test the algorithms, a set of simulations are presented: the robot KUKA LBR iiwa is controlled in different cases, where fixed or dynamic obstacles interfere with its motion. Simulations are also used to estimate the required computational effort in order to verify the transferability to a real system.

Lake Chapala is a natural ecosystem of Mexico, declared Ramsar site, currently, is an area with importance in the agricultural sector, tourism, and important source of drinking water in the Metropolitan area of Guadalajara, considered as a thermo regulatory body. This study used tools such as Rhtest, as well as analyzing extreme climate indices using RClimdex. In addition, the relationship with the change in water surface of Lake Chapala was assessed through the NDWI index, using Landsat images, between 1985 and 2018. According to the obtained results, the signs of climatic variability are detected in the study region, which, directly affects the basin runoff and water levels in the lake, as well as, the factor of water overexploitation in the basin, so it is considered that the lake conditions mostly depend on the type of management that is given to the resource. Finally, the results will help the understanding of climate variability and its water resources influence of the Lerma Chapala basin, which will assist in future research.

Single-stand selective monofunctional uracil DNA glycosylase 1 (SMUG1) works to remove uracil and certain oxidized bases from DNA during base excision repair (BER). This review provides a historical characterization of SMUG1 and 5-hydroxymethyl-2'-deoxyuridine (5-hmdU) one important substrate of this enzyme. Biochemical and structural analyses provide remarkable insight into the mechanism of this glycosylase revealing SMUG1 has a unique helical wedge which influences damage recognition during repair. Rodent studies suggest that, while SMUG1 shares substrate specificity with another uracil glycosylase UNG2, loss of SMUG1 can have unique cellular phenotypes. This review highlights the multiple roles SMUG1 may play in preserving genome stability, and how the loss of SMUG1 activity may promote cancer. Finally, we discuss recent studies indicating SMUG1 has moonlighting functions beyond BER, playing a critical role in RNA processing including the RNA component of telomerase.

Background: A Few preclinical studies have shown that Knee osteoarthritis (KOA) is linked to gut microbiome dysbiosis and chronic inflammation. This pilot study was designed to look at the gut microbiome composition in KOA patients and normal individuals with or without vitamin D deficiency (VDD, serum vitamin D <30 ng/ml). Methods: This pilot study was conducted prospectively in 24 participants. The faecal samples of all the participants were taken for DNA extraction. The V3-V4 region of 16s rRNA was amplified and the library was prepared and sequenced on the Illumina Miseq platform. Results: The mean (±SD) age was 45.5 (±10.2) years with no defined co-morbidities. Of 447 total Operational Taxonomic Units (OTUs), a differential abundance of 16 nominally significant OTUs between the groups were observed. Linear discriminate analysis (LEfSe) revealed a significant difference in bacteria among the study groups. Pseudobutyrivibrio and Odoribacter were specific for VDD while Parabacteroides, Butyricimonas, and Gordonibacter were abundant in the KOA_VDD group and Peptococcus, Intestimonas, Delftia, and Oribacterium were abundant in the KOA group. About 80% of bacterial species were common among different groups and hence labeled as core bacterial species. However, the core microbiome of KOA and VDD groups were not seen in the KOA_VDD group, suggesting that these bacterial groups were affected by the interaction of the KOA and VDD factors. Conclusion: Parabacteroides, Butyricimonas, Pseudobutyrivibrio, Odoribacter, and Gordonibacter are the predominant bacteria in vitamin D deficient patients with or without KOA. Together these results indicate an association between the gut microbiome, vitamin D, and knee osteoarthritis.

Sago (Metroxylon spp.) is an important crop in Maluku. This study aims to identify the biodiversity of sago palm and understorey vegetation around sago clumps in Maluku. The research was carried out in six sago area from September 2015 to October 2016. The Sago Plant identification was carried out through the growth phase of sago, i.e. seedlings, saplings, weaning, trunks, and ripening. Vegetation observation was done in radius 100 m2 surrounding sago clumps. The result shows that Metroxylon rumphii Mart type. (Tuni sago), M. sagus Rottb. (Molat sago) and M. Silvester Mart. (Ihur Sago) dominates sago palms area in Seram and Ambon Islands, Maluku. There are significant morphological differences between the types of sago, especially in stem height, midrib width, leaf midrib colour, number of thorns, and flower stalk length, as well as the difference of carbohydrate content. Understorey vegetation of each observation sites diverse consist of 15 families and 20 species. The families that dominate the vegetation under the sago palms are Araceae, Thelypteridaceae, and Athyriaceae. The types of plants from Araceae are taro types and broadleaf, while those from the Thelypteridaceae and Athyriaceae families are types of ferns.

The destruction of natural habitat for cropland and pastures represents a major threat to global biodiversity. Despite widespread societal concern about biodiversity loss associated with food production, consumers access to quantitative estimates of the impact of crop production on the world’s species has been very limited compared to assessments of other environmental variables such as greenhouse gas emissions or water use. Here, we present a consistent dataset of the biodiversity footprints of pastures and 175 individual crops at country level. The data were generated by combining maps of the global distribution of agricultural areas in the year 2000 with spatially explicit estimates of the biodiversity loss associated with the conversion of natural habitat to farmland. Estimates were derived for three common alternative measures of biodiversity – species richness, threatened species richness, and range rarity – of the world’s mammals, birds, and amphibians. Our dataset provides important quantitative information for food consumers and policy makers, allowing them to take evidence-based decisions to reduce the biodiversity footprint of global food production.

This article represents survey data of historical and architectural documentation of Sri Radha Binod Ashrama locally known as the Panishail temple. Temple architecture is a common feature of traditional religious architecture practice in Bangladesh. This article is a historical and architectural investigation of a less known and mixed type of Hindu temple style in the Bengal region. The Panishail temple complex has a collection of structures that include tomb, temples, and residences aged between fifty to two hundred years. Over the ages, these heritage buildings have displayed a unique architectural style of ancient Bengal and still serving as a living sacred landscape heritage. However, like most of the ancient monuments of Bangladesh, Panishail structures inside this complex stand against the threat of decay and anthropogenic destruction with no effort to conserve them. There is a need for immediate action of research, exploration and preservation to save this historic landmark. This research aims to investigate historic and physical features of the temple complex through a systematic survey and documentation effort. This research will lay a foundation for future conservation intervention on this site. Moreover, this work will significantly contribute to historic temple architecture study in Bangladesh.

Cannabis is one of the oldest cultivated crops in the history for food, fiber and drugs for thousands of years. Extension of cannabis genetic variation developed in a wide- ranging choice of varieties with various complementary phenotypes and secondary metabolites. Cannabis grow practices is very diverse, especially indoor cultivation factors, such as different lighting conditions, pot size, humidity, fertilizers. These growth factors influence a lot on the production of cannabinoids. For medical or pharmaceutical purposes, ratio of CBD or THC is very important. Plants traits and metabolic compounds are related to various conditions produced by microbes. Investigating this crosstalk between plants and microbes can play a vital role not only for stimulating the biosynthetic and signaling pathways of the host plants for the production of agronomically or pharmaceutically essential metabolic compounds but also against pathogens. This study emphasis on decoding the crosstalk between cannabis and associated microbes in the belowground environmental niches that would unravel the complexity of stabilizing cannabinoid production.

Sewage sludge was utilized into biochar using the slow pyrolysis method. The biochar was then being used for ammonium removal. The sewage sludge biochar was produced at temperature of 550°C, 600°C, 650°C, 700°C and 750°C. A few characterization tests were carried out to study about the physical and chemical properties of the biochar. For instance, moisture and ash content analysis, FTIR spectroscopy, pH Zero Point Charge, biochar yield and SEM. As the pyrolysis temperature increased, the moisture content of SSB decreased while the ash content increased. The FTIR spectra of sewage sludge biochar showed that there were various organic functional groups on the surface of the biochar which were responsible for ammonium adsorption. Furthermore, through pH Zero Point Charge analysis, pH 7.0 was the most optimum pH for the adsorption test of ammonium. The optimum adsorbent dosage was 0.01g while optimum contact time was 150 minutes. Furthermore, 1.2ppm was the most optimum concentration for adsorption process. Based on the result of the characterization tests, SSB700 was the most effective biochar for ammonium adsorption. Based on the result of kinetic and isotherm analysis, the adsorption of ammonium ions usign sewage sludge biochar was a monolayer chemisorption process.

For the KdV-Burgers equations on cylindrical and spherical waves the development of a regular profile starting from an equilibrium under a periodic perturbation at the boundary is studied. The equations describe a medium which is both dissipative and dispersive. Symmetries, invariant solutions and conservation laws are investigated. For an appropriate combination of dispersion and dissipation the asymptotic profile looks like a periodical chain of shock fronts with a decreasing amplitude (sawtooth waves). The development of such a profile is preceded by a head shock of a constant height and equal velocity which depends on spatial dimension as well as on integral characteristics of boundary condition; an explicit asymptotic for this head shock and a median of the oscillating part is found.

A mechanical ventilation system is a big support for breathing complications, in which an external solution is quite necessary to keep oxygen compensation in the patients. Its knowledge is well widespread and different equipment has been developed. However, they are very expensive and their quantity in medical centers is not sufficient, especially in Peru. Hence, it has been required to develop new methods to provide oxygen by a low cost equipment; Protofy, a research group from Spain, designed one of the first low cost mechanical ventilation systems which was medically validated by its government. In this sense, a redesign of the mechanical ventilation system was carried out according to the local requirements and available technology, a different airbag resuscitator with different properties and geometry, but maintaining its working concept based on a cam compression mechanism. Sensors and a display were added to improve the performance with a control algorithm for the rotation frequency and to show the ventilation curves over time to the medical staff. It was necessary to develop a mathematical model to relate the behavior between ventilation curves for a patient and physical variables of the design, especially in the epidemic COVID 19, that many countries are dealing with at the time research is being conducted. The mechanical ventilation system was redesigned, fabricated, and tested measuring its ventilation curves over time. Results indicate that this redesign provides a sturdy equipment able to work during a longer lifetime than the original. The replicability of the ventilation curves behavior is assured, while the mechanism dimensions are adapted for a particular airbag resuscitator. The mathematical model of the whole system can predict satisfactorily the ventilation curves over time and was used to provide the air pressure, volume, and flow as a function of the rotation angle measured by sensors.

Pomegranate extract (PG-E) has been reported to exert a protective effect in skin due to its antioxidant activity. Ingredients rich in phenolic compounds are unstable in extract solutions and, therefore, the use of a suitable nanosystem to encapsulate this type of extract could be necessary in different biotechnological applications. Thus, we investigated the capacity of Brassica oleracea L. (cauliflower) inflorescence vesicles (CI-vesicles) to encapsulate PG-E and determined the stability and the antioxidant capacity of the system over time. In addition, the protective effect against UV radiation and heavy metals in HaCaT cells was also tested. The CI-vesicles had an entrapment efficiency around 50% and accelerated stability tests did not show significant changes in the parameters tested. The results for the HaCaT cells show the non-cytotoxicity of the CI-vesicles containing PG-E and their protection against heavy metals (lead acetate and mercuric chloride) and UV-B radiation through a reduction of oxidative stress. The reduction of the percentage of deleted mtDNA (mtDNA4977, “common deletion”) in UV-treated HaCaT cells due to the presence of CI-vesicles containing PG-E indicates the mechanism of protection. Therefore, the effects of CI-vesicles loaded with PG-E against oxidative stress support their utilization as natural cosmeceuticals to protect skin health against external damage from environmental pollution and UV radiation.

Phosphorus is essential and non-substitutable chemical element required for the cellular processes of all living organisms. The main source of phosphorus in the biosphere is phosphate rock. With more than 700 Mt P2O5, Estonia holds the largest sedimentary phosphate rock deposits in European Union. Estonian phosphate rock is principally sandstone that holds abundant remains of phosphatic brachiopod shells and compared to other sedimentary rocks, is particularly outstanding by its remarkably low content of hazardous heavy metals such as Cd and saturated by valuable elements present in the rock such as rear earth elements (REEs).

We present the hardware of a cheap multi-sensor magnetometric setup, where a relatively large set of magnetic field components is measured in several positions by calibrated magnetoresistive detectors. The setup is developed to map the (inhomogeneous) field generated by a known magnetic source, which is measured and then discerned from the background (homogeneous) geomagnetic field. The data output from this hardware can be successfully and reliably used to retrieve the position and orientation of the magnetic source with respect to the sensor frame, together with the orientation of the frame with respect to the environmental field. Possible applications of the setup are briefly discussed, and a synthetic description of the methods of data elaboration and analysis is provided.

The expression microarray technique was performed to investigate the differences in gene expression between Czech Large White pigs and wild boars in the longissimus lumborum et thoracis and biceps femoris muscle tissues. The NREP gene (neuronal regeneration related protein homolog) was selected for detailed study as an expressional and functional candidate gene. NREP plays a role in the transformation of neural, muscle and fibroblast cells and in smooth muscle myogenesis. Quantitative real-time PCR results confirmed that the porcine NREP gene was expressed in both skeletal muscles and significantly overexpressed in Czech Large White pigs compared to wild boars (P &lt; 0.05). We identified 9 polymorphic sites in genomic DNA of NREP gene. Six of these polymorphisms were in complete linkage disequilibrium and therefore only 4 polymorphisms were informative. Associations of these 4 polymorphisms (HF571253:g.103G&gt;A, HF571253:g.134G&gt;A, HF571253:g.179T&gt;C and HF571253:g.402_409delT) with meat performance traits were assessed in Czech Large White pigs. New polymorphisms in NREP gene were significantly associated with parameters of daily weight gain, lean meat and backfat thickness in Czech Large White pigs. Our primary study suggested that porcine NREP may play an important role in skeletal muscle growth, fat metabolism and meat performance traits.

The zebrafish Danio rerio is suitable to study gametes as a model organism. There were &gt; 70% of zebrafish spermatozoa activated, because they were contaminated with urine or excrement. The movement of spermatozoon in water was propagated along the flagellum at 16 s after sperm activation, then damped from the end of the flagellum for 35 s and fully disappear at 61 s after activation. For artificial fertilization, milt must be added to an extender, which stops the movement of sperm and keeps the sperm motionless until fertilization. E400 was shown to be the most suitable extender as it allows to store sperm for fertilization for 6 to 12 h at 0-2oC. Sperm motility decreased only to 36% at 12 h post stripping (HPS) for E400 extender and to 19% for Kurokura extender. To achieve an optimal level of fertilization and hatching, a test tube with a well-defined amount of 6,000,000 spermatozoa in E400 extender per 100 eggs and 100 µl of activation solution has proved to be more successful than using a Petri dish. The highest fertilization and hatching rates reached 80% and 40-60%, respectively, with milt stored for 1.5 h in E400 extender at 0-2oC.

Density Functional Theory (DFT) full potential linearized augmented plane wave (FP-LAPW) method with the Modified Becke-Johnson (mBJ) approximation is used to perform spin polarised calculations of the transition metal perovskites MoScO₃ and WScO₃. Both depict half metallic behaviour with semiconducting and metallic in the minority and majority spins respectively. MoScO₃ and WScO₃ have indirect R− Γ band gaps in the minority spin channels of 3.61 and 3.82eV respectively. Moreover, they both show substantial magnetic moments of 2.99μ_B. In addition, we calculate the dielectric function, optical conductivity and the optical constants, namely, the refractive index, the reflectivity, the extinction and absorption coefficients.

Multiple sclerosis (MS) is a chronic autoimmune disease that affects the central nervous system (CNS) characterized by varying degrees of demyelination of uncertain etiology, and is associated with specific environmental and genetic factors. Upon recognition of CNS antigens, the immune cells initiate an inflammatory process which leads to destruction and deterioration of the neurons. Innate immune cells such as macrophages, dendritic cells and natural killer cells are known to play critical roles in the pathogenesis of MS. Also, the activation of peripheral CD4+ T cells by CNS antigens leads to their extravasation into the CNS causing damages that exacerbates the disease. This could be accompanied by dysregulation of T regulatory cells and other cell types functions. Experimental autoimmune encephalomyelitis (EAE) is a mouse model used to study the pathophysiology of MS disease. In this review, we highlight the roles of innate and adaptive immune players in the pathogenesis of MS and EAE.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

BACKGROUND: Manufacturing costs, along with operational performance, are among the major factors determining the selection of the propulsion system for unmanned aerial vehicles (UAVs), especially for aerial targets and cruise missiles. OBJECTIVES: In this paper, the design requirements and operating parameters of small turbofan engines for single-use and reusable UAVs are analysed to introduce alternative materials and technologies for manufacturing their compressor blades, such as sintered titanium, a new generation of aluminium and an alloy based on titanium aluminides. METHODS: To assess the influence of severe plastic deformation (SPD) on the hardening efficiency of the proposed materials, the alloys in the coarse-grained and submicrocrystalline states were studied. Changes in physical and mechanical properties of materials were taken into account. The thermodynamic analysis of the compressor was performed in a finite element analysis system (ANSYS) to determine the impact of gas pressure and temperature on the aerodynamic surfaces of compressor blades of all stages. RESULTS: Based on thermal and structural analysis, the stress and temperature maps on compressor blades and vanes were obtained, taking into account the physical and mechanical properties of advanced materials and technologies of their processing. The safety factors of the components were established based on the assessment of their stress-strength reliability. Thanks to nomograms, the possibility of using the new materials and the technologies was confirmed in view of the permissible operating temperature and safety factors of blades. CONCLUSIONS: The proposed alternative materials and production technologies for the compressor blades and vanes meet the design requirements of the turbofan at lower manufacturing costs.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Introduction: Various studies have widely documented how weight (being overweight, underweight or obese) plays a significant role in increasing health problems and adversely affects the quality of life. Out of all the weight-related issues, obesity is the number one contributing factor for causing health problems. To overcome this factor, a trial was conducted where a drug 'Lite plus’ (Garcinia Cambogia and Green Coffee bean) was given to a select number of people for a period of three months. Materials and Methods: 'Lite Plus' is a drug which contains Garcinia cambogia 500 mg + Green Coffee Bean Extract 400 mg, with a recommended dosage of 2 tablets/day with or before meals for 3 months. Most of the patients included in our study were females suffering from obesity-related problems such as PCOs and Infertility. During the trial, all patients were given the recommended dosage of 'Lite plus', while those with diabetes had the dose amended accordingly. Results: As a result of this trial, it was found that the use of 'Lite Plus' was very effective in decreasing weight/BMI with continuous use. After 6 weeks, out of the 250 respondents participating in the trial, 232 got a reduction in their BMI, and after 12 weeks (end of the trial), 29 respondents (11.6%) reached the desired level of BMI. Conclusion: Garcinia cambogia and Green Coffee bean are effective and safe in weight reduction.

The current paper aims to study the impact properties of additively manufactured Maraging steel (1.2709) using laser powder bed fusion (PBF-L) processing. The specimens were manufactured using 3Dsystems ProX 300 equipment under constant specific power input, or Andrew Number. The interactions between the build strategy and parameters, such as Hatch spacing and Scan speed was, and the impact strength and fracture were investigated. The Impact energy anisotropy was also investigated parallel and perpendicular to the build direction. Instrumented impact testing was performed, and the fractography supported that the fusion zone geometry dictated the fracture behaviour. The influence from gaseous elements such as Nitrogen, Oxygen and Hydrogen was found insignificant at the levels found in the printed material.

With the year 2020, the world faced a new threat that affects all areas of life, negatively affects production in all areas, and paralyzes social life. The measures and restrictions taken by the country's governments to prevent the epidemic from spreading rapidly in the society with the effect of the Covid-19 virus, which first appeared in China and spread all over the world, brought a new lifestyle. Covid-19 has been much the impact on electricity use and electricity production in the period in Turkey as in other countries. There was a sharp decline in commercial and industrial electricity use. The coronavirus effect has also been reflected in the electricity demand and the consumption amount has undergone a great negative change. Due to the enactment of measures against the new type of coronavirus (COVID-19) epidemic and the partial or full-time curfews, electricity consumption was moved to homes, supermarkets, and hospitals in April 2020 from places where mass consumption is intense, such as industry, workplaces, and educational institutions. In this study, Covid-19 period, the first cases were examined electricity production and consumption in Turkey as of the date it is seen throughout, in comparison with electricity consumption data in the same month of the previous years corresponding to this period, the effects on electricity generation and consumption habits of this period were examined.

The energy E takes the place of the gravitational mass m_G to produce gravity [1]. We wonder whether the inertial mass m_i in the inertial force is also replaced by E. The experiments to measure the inertial force and weight of a carrier are presented. Now we can test the principle of equivalence and study foundations of physics in condensed matter.

Recently, Kim-Kim [13] have introduced polyexponential functions as an inverse to the polylogarithm functions, and constructed type 2 poly-Bernoulli polynomials. They have also introduced unipoly functions attached to each suitable arithmetic function as a universal concept. Inspired by their work, in this paper, we introduce a new class of the Frobenius-Genocchi polynomials. We derive the diverse formulas and identities covering some summation formulas, derivative formula and correlations with Bernoulli polynomials and numbers, Stirling numbers of the both kinds, degenerate Frobenius-Genocchi polynomials and degenerate Frobenius-Euler polynomials. Moreover, by using the unipoly function as following Kim-Kim's work in <cite>Kim1</cite>, we consider degenerate unipoly-Frobenius-Genocchi polynomials and investigate some formulas and relationships with Daehee numbers, degenerate Frobenius-Genocchi numbers and Stirling numbers of the first kind. Finally, we obtain an Gaussian integral representation of the Frobenius-Genocchi polynomials in terms of the 2-variable Hermite polynomials.

Cadherins are a group of membrane proteins responsible for cell adhesion. They are crucial for cell sorting and recognition during the morphogenesis, but also play many other roles such as assuring tissue integrity and resistance to stretching, mechanotransduction, cell signaling, regulation of cell proliferation, apoptosis, survival, carcinogenesis, etc. Within the cadherin superfamily, the E- and N-cadherin have been especially well studied. They are involved in many aspects of sexual development and reproduction, such as germline development and gametogenesis, gonad development and functioning, and fertilization. E-cadherin is expressed in the primordial germ cells, (PGCs) and also participates in PGC migration to the developing gonads where they become enclosed by the N-cadherin-expressing somatic cells. The differential expression of cadherins is also responsible for the establishment of the testis or ovary structure. In the adult testes, the N-cadherin is responsible for the integrity of the seminiferous epithelium, regulation of sperm production, and the establishment of the blood-testis barrier. Sex hormones regulate the expression and turnover of N-cadherin influencing the course of spermatogenesis. In the adult ovaries, E- and N-cadherin assure the integrity of ovarian follicles and the formation of corpora lutea. Cadherins are expressed in the mature gametes, and facilitate the capacitation of sperm in the female reproductive tract, and gamete contact during fertilization. The germ cells and accompanying somatic cells express a series of different cadherins, however, their role in gonads and reproduction is still unknown. In this review, we show what is known and unknown about the role of cadherins in the germline and gonad development, and suggest the topics for future research.

In this paper, we introduce a new type of degenerate poly-Fubini polynomials and numbers, are called degenerate poly-Fubini polynomials and numbers, by using the degenerate polylogarithm function and derive several properties on the degenerate poly-Fubini polynomials and numbers. In the last section, we also consider the degenerate unipoly-Fubini polynomials attached to an arithmetic function, by using the degenerate polylogarithm function and investigate some identities of those polynomials. In particular, we give some new explicit expressions and identities of degenerate unipoly polynomials related to special numbers and polynomials.

Osteopetrosis is a group of rare inheritable disorders of the skeleton characterized by increased bone density. The disease is remarkably heterogeneous in clinical presentation and often misdiagnosed. Therefore, genetic testing and molecular pathogenicity analysis are essential for precise diagnosis and new targets for preventive pharmacotherapy. Mutations in the CLCN7 gene give rise to the complete spectrum of osteopetrosis phenotypes and are responsible for about 75% of cases of autosomal dominant osteopetrosis. In this study, we report the identification of a novel variant in the CLCN7 gene in a patient diagnosed with osteopetrosis and provide evidence for its significance (likely deleterious) based on extensive comparative genomics, protein sequence and structure analysis. A set of automated bioinformatics tools used to predict consequences of this variant identified it as deleterious or pathogenic. Structure analysis revealed that the variant is located at the same “hot spot” as the most common CLCN7 mutations causing osteopetrosis. Deep phylogenetic reconstruction showed that not only Leu614Arg, but any non-aliphatic substitutions in this position are evolutionarily intolerant, further supporting the deleterious nature of the variant. The present study provides further evidence that reconstructing a precise evolutionary history of a gene helps predicting phenotypical consequences of variants of uncertain significance.

Since the early 1980s, a large number of research works on enzymes from the red king crab hepatopancreas have been conducted. These studies have been relevant both from a fundamental point of view for studying the enzymes of marine organisms and in terms of the rational management of nature to obtain new and valuable products from the processing of crab fishing waste. Most of these works were performed by Russian scientists due to the area and amount of waste of red king crab processing in Russia (or the Soviet Union). However, the close phylogenetic kinship and the similar ecological niches of commercial crab species and the production scale of the catch provide the bases for the successful transfer of experience in the processing of red king crab hepatopancreas to other commercial crab species mined worldwide. This review describes the value of recycled commercial crab species, discusses processing problems, and suggests possible solutions to these problems. The main emphasis is placed on the enzymes of the hepatopancreas as the most highly salubrious product of waste processed from red king crab fishing.

ZnS-CdS composite nano-powder doped with (0.01 mol %) Cobalt has been collected by a co-precipitation process at 300 K. The sample is characterized by structural, combined spectroscopic methods and magnetic studies. The prepared samples were belonging to cubic structure no impurity phases were observed. Doping of cobalt increase the neighborhood strain assessment and a decreases lattice constants decides from x-ray diffraction data. The crystallite size is 10.42nm. From UV-absorption and EPR studies revealed that the energy band gap of Co2+ doped ZnS-CdS composite nanopowder and extension of sp-d exchange interactions and common d-d transitions. The variation in the energy bandgap varies as a function of cobalt concentration is due to structural modification. Photoluminescence spectrum reveals the defect-related emissions and shows the formation of luminescence. FT-IR spectrum confirmed the feature vibrational manner of Zn, Cd, O–H and sulfide ions are in the host lattice. The doping-induced magnetic properties are studied by vibrating sample magnetometer which matches with the theoretical values besides ferromagnetic nature. Magnetic studies confirm the ferromagnetic nature of the material. Surface morphology and chemical homogeneity studies were carried out by using SEM with EDAX. Transmission electron microscope recommends the crystalline nature of nanoparticles, with average particle size is of the order of 20-100nm.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

A simplified nonlinear dispersive system of BBM-type, initially derived by D. Mitsotakis, is employed here in order to model the generation and propagation of surface water waves over variable bottom. The simplification consists in applying the so-called Boussinesq approximation. Using the finite element method and the FreeFem++ software, we solve numerically this system for three different complexities for the bathymetry function: a flat bottom case, a variable bottom in space, and a variable bottom both in space and in time. The last case is illustrated with the Java 2006 tsunami event. This article is designed rather as a tutorial paper even if it contains the description of completely new adaptation techniques.

COVID-19 has created anxiety not only in individuals but also in health organizations, and countries worldwide. Not a single industry is left un-influenced and loss is being estimated in billions of dollars. The widespread of this pandemic disease has challenged researchers all over the world. Some of the researchers are working to invent its cure while, others are applying computing technologies to stop its spread, by analyzing and identifying patterns for prediction and forecasting. This is by no doubt the hottest area of research for the last 100 years. This survey has targeted the research published in computing sub-domains to combat the pandemic. The survey has clustered the scientific efforts into logical groups: surveillance, metrological effects, social media analytics, image processing and business and economy, analysis and modeling. It will serve as a leading source for the followings: researchers who want to identify what has been achieved in different computing sub-domains, those who need fresh authenticated datasets openly accessible for different research contexts and what are future directions in this area of research. The findings of analysis and modeling can be also useful for government agencies who want to set priorities and formulate policies.

(1) Background: The importance of this article is to analyze the technological developments in the field of the Internet and Internet technologies and to determine their significance for the sustainable development which will result in the emergence of the Society 5.0; (2) The authors used automated content analysis for the analysis of 552 articles published in 306 scientific journals indexed by SCII and/or SCI - EXPANDED (Web of Science (WOS) platform) between the years 1996 and 4/2020. The goal of the research was to present the relationship between the internet and sustainable development. (3) Results: The results of the analysis show that the top four most important themes in the selected journals were “development”, “information”, “data”, and “business and services”. (4) Conclusions: Our research approach emphasizes the importance of the culmination of scientific innovation with the conceptual, technological and contextual frameworks of the internet and internet technology usage and its impact on sustainable development and emergence of the Society 5.0

Serum transferrin (sTf) plays a pivotal role in regulating iron biodistribution and homeostasis within the body. The molecular details of sTf Fe(III) binding, blood transport, and cellular delivery through transferrin receptor-mediated endocytosis are generally well-understood. Emerging interest exists in exploring sTf complexation of nonferric metals as it facilitates the therapeutic potential and toxicity of several of them. This review explores recent X-ray structural and physiologically relevant metal speciation studies to understand how sTf partakes in the bioactivity of key non-redox active hard Lewis acidic metals. It challenges preconceived notions of sTf structure function correlations that were based exclusively on the Fe(III) model by revealing distinct coordination modalities that nonferric metal ions can adopt and different modes of binding to metal-free and Fe(III)-bound sTf that can directly influence how they enter into cells and, ultimately, how they may impact human health. This knowledge informs on biomedical strategies to engineer sTf as a delivery vehicle for metal-based diagnostic and therapeutic agents in the cancer field. It is the intention of this work to open new avenues for characterizing the functionality and medical utility of nonferric-bound sTf and to expand the significance of this protein in the context of bioinorganic chemistry.

OVOL proteins (OVOL1 and OVOL2), vertebrate homologs of Drosophila OVO, are critical regulators of epithelial lineage determination and differentiation during embryonic development in tissues such as kidney, skin, mammary epithelia, testis. OVOL inhibits EMT and can promote MET; moreover, they can regulate the stemness of cancer cells, thus playing an important role during cancer cell metastasis. Due to their central role in differentiation and maintenance of epithelial lineage, OVOL overexpression has been shown to be capable of reprogramming fibroblasts to epithelial cells. Here, we review the roles of OVOL mediated epithelial differentiation across multiple contexts – embryonic development, cancer progression, and cellular reprogramming.

Seafood is considered one of the main food allergen sources by the European Food Safety Authority (EFSA). It comprises several distinct groups of edible aquatic animals including fish and shellfish such as crustacean and mollusks. Recently the EFSA recognized the high risk of food allergy over the world and established the necessity of developing new methodologies for its control. Consequently, accurate, sensitive and fast detection methods for seafood allergy control and detection in food products are highly recommendable. In this work, we present a comprehensive review of the applications of the proteomics methodologies for the detection and quantification of seafood allergens. For that, two consecutive proteomics strategies (Discovery and Targeted Proteomics) applied for the study and control of seafood allergy are reviewed in detail. In addition, future directions and new perspectives were also provided.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

Background & Motivation: Stroke outcomes following revascularization therapy (intravenous thrombolysis, IVT, and/or mechanical thrombectomy, MT) depend critically on time from stroke onset to treatment. Different service configurations may prioritise time to IVT or time to MT. In order to evaluate alternative acute stroke care configurations, it is necessary to estimate clinical outcomes given differing times to IVT and MT. Method: Model using an algorithm coded in Python. This is available at https://github.com/MichaelAllen1966/stroke_outcome_algorithm. Results: We demonstrate how the code may be used to estimate clinical outcomes given varying times to IVT and MT. Conclusion: Python code has been developed and shared to enable estimation of clinical outcome given times to IVT and MT. Here we share pseudocode and links to full Python code.

Multipartite entanglement is a resource for application in disparate protocols, of computing, communication and cryptography. Nested entanglement provides resource-states for quantum information processing. In this paper, Matryoshka quantum resource-states, which contain nested entanglement patterns, has been studied. A novel scheme for the generation of such quantum states has been proposed using an anisotropic XY spin-spin interaction-based model. The application of the Matryoshka GHZ-Bell states for n-qubit teleportation is reviewed and an extension to more general Matryoshka ExhS-Bell states is posited. An example of Matryoshka ExhS-Bell states is given in the form of the genuinely entangled seven-qubit Xin-Wei Zha state. Generation, characterisation and application of this seven-qubit resource state in theoretical schemes for quantum teleportation of arbitrary one, two and three qubits states, bidirectional teleportation of arbitrary two qubit states and probabilistic circular controlled teleportation are presented.

The involvement of macular function in its preganglionic elements, during the neurodegenerative process of multiple sclerosis (MS), is controversial. In this case-control observational and retrospective study, we assessed multifocal electroretinogram (mfERG) responses from 41 healthy Controls, 41 relapsing-remitting MS patients without optic neuritis (ON) (MS-noON Group), 47 MS patients with ON: 27 with full recovery of high-contrast best corrected visual acuity (BCVA) (MS-ON-G Group) and 20 with poor recovery of BCVA (MS-ON-P Group). MfERG N1 and P1 implicit times (ITs), and N1-P1 response amplitude densities (RADs) were measured from concentric rings (R) with increasing foveal eccentricity: 0-5° (R1), 5-10° (R2), 10-15° (R3), 15-20° (R4), 20- 25° (R5), and from retinal sectors [superior, nasal, inferior and temporal] between 0-15° and 0- 25°. In MS-ON-P Group, mean mfERG RADs detected from R1 (0-5°) and from the central nasal quadrant (0-15°) were significantly reduced (p<0.01) with respect to those of Control, MS-noON and MS-ON-G Groups. No other significant differences between Groups for any mfERG parameters were found. Our results suggest that in MS, exclusively after ON with poor recovery of BCVA, the neurodegenerative process can induce dysfunctional mechanisms involving photoreceptors and bipolar cells of the fovea and of the more central nasal macular area.

During the current COVID-19 pandemic caused by SARS-CoV-2, clinicians and scientists are working assiduously to unravel its pathophysiology and find effective treatments. An impressive number of papers has been published on SARS-CoV-2, exposing the complexity of the disease, the tendency of scientists to form hypotheses within their area of expertise, and the lack of orchestration of research. Hypotheses and research findings mainly complement each other, though sometimes controversies can be discerned among various theories and study results. Our overview aims to portray the ‘big picture’ of COVID-19, visualising the interwovenness of different pathophysiological pathways, with a focus on cytokine-induced pathology, the sequelae of ACE2 downregulation, and thrombosis associated with microvascular injury. It aids in overseeing the effects of repurposed drugs on intended targets, but also alerts to the (adverse) effects on interacting pathways. The overview shows how comorbidities probably increase susceptibility to (severe) COVID-19 and provides the possible pathophysiological origin of signs, symptoms, and biochemical abnormalities.

In this paper, modelling designing and simulation of a simple voltage amplidyne system is done using robust control theory. In order to increase the performance of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers are used. The open loop response of the voltage amplidyne system shows that the system can amplify the input 7 times. Comparison of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers to track a desired step input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed voltage amplidyne system with H ∞ optimal control synthesis controller in improving the percentage overshoot and the settling time.

The commercial cultivation of microalgae began in the 1960s and Chlorella was one of the first target organisms. The species has long been considered a potential source of renewable energy, an alternative for phytoremediation, and more recently, as a growth and immune stimulant. However, Chlorella vulgaris, which is one of the most studied microalga, has never been comprehensively profiled chemically. In the present study, comprehensive profiling of the Chlorella vulgaris metabolome grown under normal culture conditions was carried out, employing tandem LC-MS/MS to profile the ethanolic extract and GC-MS for fatty acid analysis. The fatty acid profile of C. vulgaris was shown to be rich in omega-6, -7, -9, and -13 fatty acids, with omega-6 being the highest, representing more than sixty percent (>60%) of the total fatty acids. This is a clear indication that this species of Chlorella could serve as a good source of nutrition when incorporated in diets. The profile also showed that the main fatty acid composition was that of C₁₆-C₁₈ (>92%), suggesting that it might be a potential candidate for biodiesel production. LC-MS/MS analysis revealed carotenoid constituents comprising violaxanthin, neoxanthin, lutein, β-carotene, vulgaxanthin I, astaxanthin, and antheraxanthin, along with other pigments such as the chlorophylls. In addition to these, amino acids, vitamins, and simple sugars were also profiled, and through mass spectrometry-based molecular networking, 48 phospholipids were putatively identified.

At present time world is facing from the coronavirus disease known as Covid-19. The first case of the coronavirus was reported in the December, 2019 in the Wuhan city of China which is known as the major transportation hub of China. After the spread of Covid-19 many countries have shut down their sea ports and airports. They have banned the import and export activities. Also, China is the major distributor of the raw materials which affect the manufacturing activities across the globe due to lockdowns. India is the developing country due to the Covid-19 spread the cases reported in the India government has lockdown the country for 41 days which affected the manufacturing activities and majorly it affects the supply chains and economy of the country. In the present paper we have discussed the effect of Covid-19 on Indian economy and on supply chains in India. There are total of 18 critical barriers are found out which affected the supply chains in the India. It is expected that this study will helpful the researchers to develop the conceptual models to overcome from this issue.

The sudden pervasive of severe acute respiratory syndrome Covid-19 has been leading the universe into a prominent crisis. It has influenced each zone, for example, industrial area, horticultural zone, Public transportation, economic zone, and so on. So as to see how Covid-19 affected the globe, we conducted an investigation characterizing the effects of the pandemic over the world using Machine Learning (ML) method. Prediction is a typical data science exercise that helps the administration with function planning, objective setting, and anomaly detection. We propose an additive regression model with interpretable parameters that can be naturally balanced by experts with domain intuition about the time series. We focus on global data beginning from 22^nd January 2020, till 26^th April 2020 and performed dynamic map visualization of Covid-19 expansion globally by date wise and predicting the spread of virus on all countries and continents. The major advantages of this work include accurate analysis of country-wise as well as province/state-wise confirmed cases, recovered cases, deaths, prediction of pandemic viral attack and how far it is expanding globally.

Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) as the current coronavirus pandemic is an infectious disease that initially confirmed in China in late December 2019. In this study, we analyzed 131 complete sequences of SARS-CoV-2 from Asia. Our results show that there are fifteen major mutations in Asia which most of them are co-evolved. There were five groups based on co-mutations which three of them resulted in clade G including (241C>T, 3037C>T, 14408C>T, and 23403A>G), (28881G>A, 28882G>A, 28883G>C and 23403A>G) and (25563G>T and 23403A>G). Co-mutations in (8782C>T and 28144T>C) and (1397G>A, 28688T>C, 29742G>T and 11083G>T) were clustered in clade S and a new clade outside of GISAID classification, respectively. Sequences with a mutation in 26144G>T had low variability without any co-mutation which formed clade V. In this study, we showed that Most of the circulated viruses in Asia collected in five co-mutation groups which may affect the transmissibility and vaccine designing strategies.

Let f : V → V be a Cohomological Expanding Mapping¹ of a smooth complex compact homogeneous manifold with $ dim_{\mathbb{C}}(\Vc)=k \ge 1$ and Kodaira Dimension $\leq 0$. We study the dynamics of such mapping from a probabilistic point of view, that is, we describe the asymptotic behavior of the orbit $ O_{h} (x) = \{h^{n} (x), n \in \mathbb{N} \quad \mbox{or}\quad \mathbb{Z}\}$ of a generic point. Using pluripotential methods, we have constructed in our previous paper \cite{Armand4} a natural invariant canonical probability measure of maximal Cohomological Entropy $ \nu_{h} $ such that ${\chi_{2l}^{-m}} (h^m)^\ast \Omega \to \nu_h \qquad \mbox{as} \quad m\to\infty$ for each smooth probability measure $\Omega $ in $\Vc$ . We have also studied the main stochastic properties of $ \nu_{h}$ and have shown that $ \nu_{h}$ is a smooth equilibrium measure , ergodic, mixing, K-mixing, exponential-mixing. In this paper we are interested on equidistribution problems and we show in particular that $ \nu_{h}$ reflects a property of equidistribution of periodic points by setting out the Third and Fourth Main Results in our study. Finally we conjecture that $$\nu_h:=T_l^+ \wedge T_{k-l}^-,$$ $$\dim_\HH(\nu_h)= \Psi h_{\chi}(h) , $$ $$\dim_\HH( \mbox{Supp} T_l^+) \geq 2(k-l) + \frac{\log \chi_{2l}}{\psi_l},$$ $$|\langle \nu_m^x-\nu_h,\zeta\rangle|\leq M \Big[1+\log^+{1\over D(x,\Tc)}\Big]^{\beta/2}\|\zeta\|_{\Cc^\beta} \gamma^{-\beta m/2}$$ and $$|\langle \nu_m^x-\nu_h,\zeta\rangle|\leq M \Big[1 +\log^+{1\over D(x,E_\gamma)}\Big]^{\beta/2}\|\zeta\|_{\Cc^\beta} \gamma^{-\beta m/2}.$$

A precise understanding of the genes and associated genomes of SARS-CoV2 is important for various reasons such as discovering origin of the virus and virulence and so on. A thorough descriptive understanding of the SARS-CoV2 genomes and other coronavirus of the beta-coronavirus genus is primarily important. In this article, a set of ten genomes of four CoVs and their associated genes are considered for this present study. A spatial representations of nucleotide bases including purine-pyrimidine representations of the different genes of the corresponding genomes are quantified using Hurst exponent, Shannon entropy and density estimation of different nucleotides including GC content, in order to draw a comparison and contrast among the ten genomes of different types of CoVs which include MERS, SARS-CoV, HKU1 (Human Coronavirus) and associated their genes.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

Plasma Electrolytic Oxidation (PEO) is a surface treatment, similar to anodizing, that produces thick oxide films on the surface of metals. In the present work, PEO coatings were obtained on zinc-aluminized (ZA) carbon steel using as electrolyte a solution containing sodium silicate and potassium hydroxide, and working with high current densities and short treatment times in DC mode. The surface morphology resulted the typical one of PEO layers, with the presence of a lot of pores and micro-cracks. Considering the cross section, the thickness of the coating was strongly influenced by the process parameters, with different dissolution grades of the ZA layer depending on the current density and treatment time. The PEO layer resulted mainly composed by aluminum and zinc oxides and silicates. The corrosion resistance was remarkable increased in the samples with the PEO coating.

The tumor organoid (tumoroid) model in three-dimensional (3D) culture systems has been developed to reflect more closely the in vivo tumors than 2D-cultured tumor cells. Notably, extracellular vesicles (EVs) are efficiently collectible from the culture supernatant of gel-free tumoroids. Matrix metalloproteinase (MMP) 3 is a multi-functional factor playing crucial roles in tumor progression. However, roles of MMP3 within tumor growth and EVs have not unveiled. Here, we investigated the protumorigenic roles of MMP3 on integrities of tumoroids and EVs. We generated MMP3-knockout (KO) cells using the CRISPR/Cas9 system from rapidly metastatic LuM1 tumor cells. Moreover, we established fluorescent cell lines with palmitoylation signal-fused fluorescent proteins (tdTomato and enhanced GFP). Then we confirmed the exchange of EVs between cellular populations and tumoroids. LuM1-tumoroids released large EVs (300-1000 nm) and small EVs (50-200 nm) while the knockout of MMP3 resulted in the additional release of broken EVs from tumoroids. The loss of MMP3 leads to a significant reduction in tumoroid size and to the development of the necrotic area within tumoroids. MMP3 and CD9 (a category-1 EV marker tetraspanin protein) were significantly down-regulated in MMP3-KO cells and their EV fraction. These weakened phenotypes by MMP3 KO were markedly rescued by the addition of MMP3-rich EVs or conditioned medium (CM) collected from LuM1-tumoroids, which caused a dramatic rise in the expression of MMP3, CD9, and Ki-67 (a marker of proliferating cells) in the MMP3-null/CD9-low tumoroids. Notably, MMP3 enriched in tumoroids-derived EVs and CM deeply penetrated into recipient MMP3-KO tumoroids, resulting in a remarkable enlargement of solid tumoroids, while MMP3-null EVs did not. These data demonstrate that EVs can mediate molecular transfer of MMP3 resulting in increasing the proliferation and CD9+ tumorigenesis, indicating crucial roles of MMP3 in tumor progression.

Marine clay deposits are commonly found worldwide. Considering the cost of dumping and the related environmental concerns, an alternative solution involving the reuse of soils that have poor conditions is crucial. In this research, the authors examined the durability of marine deposited clays and compiled a corresponding database. The use of slag alone as a binder, at any percentage, increased the accumulated mass loss (ALM) up to 2%. However, the use of lime as the third binder seemed to accelerate the chemical reactions associated with the hydration of clay and cementitious material and to enhance the chemical stability, i.e., samples that included both lime and slag experienced the same ALM as samples treated with cement only. Scanning electron microscopy analysis confirmed the durability improvements of these clays. The proposed unconfined compressive strength and accumulated mass loss relationship yielded practical approximation for the fine- and coarse-grained soils blended with up to three binders until 60 days of curing.

The popularity of deep reinforcement learning (DRL) methods in economics have been exponentially increased. DRL through a wide range of capabilities from reinforcement learning (RL) and deep learning (DL) for handling sophisticated dynamic business environments offers vast opportunities. DRL is characterized by scalability with the potential to be applied to high-dimensional problems in conjunction with noisy and nonlinear patterns of economic data. In this work, we first consider a brief review of DL, RL, and deep RL methods in diverse applications in economics providing an in-depth insight into the state of the art. Furthermore, the architecture of DRL applied to economic applications is investigated in order to highlight the complexity, robustness, accuracy, performance, computational tasks, risk constraints, and profitability. The survey results indicate that DRL can provide better performance and higher accuracy as compared to the traditional algorithms while facing real economic problems at the presence of risk parameters and the ever-increasing uncertainties.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

The magnetic field of the earth plays an important role in the ecosystem, and the magnetic field of celestial bodies is also important in the formation of cosmic large-scale structures, but the origin and evolution of the celestial magnetic field is still an unresolved mystery. Many hypotheses to explain the origin have been proposed, but there are some insurmountable difficulties for each one. At present, the theory widely accepted in scientific society is the dynamo model, it says that, the movement of magnetofluid inside celestial bodies, which can overcome the Ohmic dissipative effect and generate persistent weak electric current and macroscopic magnetic field. However, this model needs an initial seed magnetic field, and the true values of many physical parameters inside the celestial body are difficult to obtain, and there is no stable solution to the large range of fluid motion. These are all difficulties for the dynamo model. Furthermore, it is difficult for the dynamo to explain the correlation between the dipole magnetic field and angular momentum of a celestial body. In this paper, by calculating the interaction between spin of particles and gravity of celestial body according to Clifford algebra, we find that a rotational celestial body provides a field $\Omega^\alpha$ for spins, which is similar to the magnetic field of a dipole, and the spins of charged particles within the celestial body are arranged along the flux line of $\Omega^\alpha$, then a macroscopic magnetic field is induced. The calculation shows that the strength of $\Omega^\alpha$ is proportional to the angular momentum of the celestial body, which explains the correlation between the magnetic intensity and angular momentum. The results of this paper suggest that further study of the effects of internal variables such as density, velocity, pressure and temperature of a celestial body on $\Omega^\alpha$ may provide some new insights into the origin and evolution of celestial magnetic field.

Despite the long and extensive history of 3D technology, it has recently attracted the attention of researchers. This technology has become the center of interest of young people because of the real feelings and sensations it creates. People see their environment as 3D because of their eye structure. In this study, it is hypothesized that people lose their perception of depth during sleepy moments and that there is a sudden transition from 3D vision to 2D vision. Regarding these transitions, the EEG signal analysis method was used for deep and comprehensive analysis of 2D and 3D brain signals. In this study, a single-stream anaglyph video of random 2D and 3D segments was prepared. After watching this single video, the obtained EEG recordings were considered for two different analyses: the part involving the critical transition (transition-state) and the state analysis of only the 2D versus 3D or 3D versus 2D parts (steady-state). The main objective of this study is to see the behavioral changes of brain signals in 2D and 3D transitions. To clarify the impacts of the human brain’s power spectral density (PSD) in 2D-to-3D (2D_3D) and 3D-to-2D (3D_2D) transitions of anaglyph video, 9 visual healthy individuals were prepared for testing in this pioneering study. Spectrogram graphs based on Short Time Fourier transform (STFT) were considered to evaluate the power spectrum analysis in each EEG channel of transition or steady-state. Thus, in 2D and 3D transition scenarios, important channels representing EEG frequency bands and brain lobes will be identified. To classify the 2D and 3D transitions, the dominant bands and time intervals representing the maximum difference of PSD were selected. Afterward, effective features were selected by applying statistical methods such as standard deviation (SD), maximum (max), and Hjorth parameters to epochs indicating transition intervals. Ultimately, k-Nearest Neighbors (k-NN), Support Vector Machine (SVM), and Linear Discriminant Analysis (LDA) algorithms were applied to classify 2D_3D and 3D_2D transitions. The frontal, temporal, and partially parietal lobes show 2D_3D and 3D_2D transitions with a good classification success rate. Overall, it was found that Hjorth parameters and LDA algorithms have 71.11% and 77.78% classification success rates for transition and steady-state, respectively.

In this paper, we compare the performance between systems of ordinary and (Caputo) fractional differential equations depicting the susceptible-exposed-infectious-recovered (SEIR) models of diseases. In order to understand the origins of both approaches as mean-field approximations of integer and fractional stochastic processes, we introduce the fractional differential equations as approximations of some type of fractional nonlinear birth--death processes. Then, we examine validity of the two approaches against empirical courses of epidemics; we fit both of them to case counts of three measles epidemics that occurred during the pre-vaccination era in three different locations. While FDEs appear more flexible in fitting empirical data, our ODEs offered better fits to two out of three data sets. Important differences in transient dynamics between these modeling approaches are discussed.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.

Designing and development of agricultural robot is always a challenging issue, because of robot intends to work an unstructured environment and at the same time, it should be safe for the surrounded plants. Therefore, traditional robots cannot meet the high demands of modern challenges, such as working in confined and unstructured workspaces. Based on current issues, we developed a new tomato harvesting wire-driven discrete continuum robot arm with a flexible backbone structure for working in confined and extremely constrained spaces. Moreover, we optimized a tomato detaching process by using newly designed gripper with passive stem cutting function. Moreover, by designing the robot we also developed ripe tomato recognition by using machine learning. This paper explains the proposed continuum robot structure, gripper design, and development of tomato recognition system.

In the present paper four passive micromixers designs (G1, G2, G3 and G4) inspired on distillation columns trays were proposed. The devices performance was assessed by numerical simulations. The mixing performance was investigated for a Reynolds number range from 0.01 to 100 and channel height of 200 µm, 500 µm and 1000 µm for oil/ethanol flow. G1 and G4 designs provided high mixing index (> 0.975). The G1 device achieved superior mixing performance with a moderate pressure drop (about 0.5 MPa) due to the induced flow recirculation pattern for a relative high flow rate of 0.21 L/min, highlighting the potential use of such microdevice for scale-up and numbering-up of microdevices in modular chemical plant processing.

Fucoidan is a brown algae-derived polysaccharide having several biomedical applications. This study simultaneously compares the anticancer activities of crude fucoidans from Fucus vesiculosus and Sargassum filipendula, and effects of low (LMW, 10-50kDa), medium (MMW, 50-100kDa) and high (HMW, >100kDa) molecular weight fractions of S. filipendula fucoidan against osteosarcoma cells. Glucose, fucose and acid levels were lower and sulphation was higher in F. vesiculosus crude fucoidan compared to S. filipendula crude fucoidan. MMW had highest the levels of sugars, acids and sulphation among molecular weight fractions. There was a dose dependent drop in focal adhesion formation and proliferation of cells for all fucoidan-types, but F. vesiculosus fucoidan and HMW had the strongest effects. G1-phase arrest was induced by F. vesiculosus fucoidan, MMW and HMW, however F. vesiculosus fucoidan treatment also caused accumulation in sub G1-phase. Mitochondrial damage occurred for all fucoidan-types, however F. vesiculosus fucoidan led to mitochondrial fragmentation. Annexin V/PI, TUNEL and cytochrome c staining confirmed stress induced apoptosis-like cell death for F. vesiculosus fucoidan but features of stress-induced necrosis-like cell death for S. filipendula fucoidans. There was also variation in penetrability of different fucoidans inside the cell. These differences in anti-cancer activity of fucoidans are applicable for osteosarcoma treatment.

In this work, some numerical radius inequalities based on the recent Dragomir extension of Furuta's inequality are obtained. Some particular cases are also provided.

Modularity is arguably one of the most influential theses guiding research on brain and cognitive function since phrenology. This paper considers the following question: is modularity entailed by recent Bayesian models of brain and cognitive function, especially the predictive processing framework? It starts by considering three of the most well-articulated arguments for the view that modularity and predictive processing work well together. It argues that all three kinds of arguments for modularity come up short, albeit for different reasons. The analysis in this paper, although formulated in the context of predictive processing, speaks to broader issues with how to understand the relationship between functional segregation and integration and the reciprocal architecture of the predictive brain. These conclusions have implications for how to study brain and cognitive function. Specifically, when cognitive neuroscience works within an acyclic Markov decision scheme, adopted by most Bayesian models of brain and cognitive function, it may very well be methodologically misguided. This speaks to an increasing tendency within the cognitive neurosciences to emphasise recurrent and reciprocal neuronal processing captured within newly emerging dynamical causal modelling frameworks. The conclusions also suggest that functional integration is an organising principle of brain and cognitive function.

Paper recycling has increased in recent years. A principal consequence of this process is the problem of addressing polymeric components known as stickies. A deep characterization of stickies sampled over one year in a recycled paper industry in México was performed. Based on their chemical structure, an enzymatic assay was performed using lipases. Compounds found in stickies by Fourier-Transform Infrared spectrometry were poly (butyl-acrylate), dioctyl phthalate, poly (vinyl-acetate), and poly (vinyl-acrylate). Pulp with 4% consistency and pH=6.2 was sampled directly from the mill once macro stickies were removed. Stickies were quantified by counting the tacky macrostructures in the liquid fraction of the pulp using a Neubauer chamber before the paper was made, and they were analyzed with rhodamine dye and a UV lamp. Of the two enzymes evaluated, the best treatment condition used Lipase 30G at a concentration of 0.44 g/L, which produced a 35.59% decrease in stickies. SebOil DG showed a smaller stickies reduction of 21.5% when used at a concentration of 0.33 g/L. Stickies in kraft paper processes were actively controlled by the action of lipases, and future research should focus on how this enzyme recognizes its substrate and should apply synthetic biology to improve lipase specificity.

Accumulating evidence suggests that mast cells should play critical roles in disruption and maintenance of intestinal homeostasis, although it remains unknown how they affect local microenvironment. Interleukin-9 (IL-9) was found to play critical roles in intestinal mast cell accumulation induced in various pathological conditions, such as parasite infection and oral allergen-induced anaphylaxis. Newly recruited intestinal mast cells trigger inflammatory responses and damage epithelial integrity through release of a wide variety of mediators including mast cell proteases. We established a novel culture model (mucosal mast cell-like cultured mast cells, MMC-like MCs), in which murine IL-3-dependent bone marrow-derived cultured mast cells (BMMCs) were further cultured in the presence of stem cell factor and IL-9. In MMC-like MCs, drastic up-regulation of Mcpt1 and Mcpt2 was found. Although histamine storage and tryptase activity were significantly downregulated in the presence of SCF and IL-9, it was entirely reversed when mast cells were co-cultured with a murine fibroblastic cell line, Swiss 3T3. MMC-like MCs underwent degranulation upon IgE-mediated antigen stimulation, which was found to less sensitive to lower concentrations of IgE in comparison with BMMCs. This model might be useful for investigation of the spatiotemporal changes of newly recruited intestinal mast cells.

In the year 2017, about 89 percent of the total energy consumed in the US was produced using non-renewable energy sources, and about 43 percent of tenant households were cost-burdened. Local governments are in a unique position to facilitate green affordable housing that could reduce cost burdens, environmental degradation, and environmental injustice. Nonetheless, limited studies have made progress on costs and benefits of green affordable housing to guide decision-making, particularly in small communities. This study investigates density bonus options for green affordable housing by analyzing construction costs, sale prices, and spillover effects for green certifications and affordable housing units. The authors employ construction costs and sale data from 422 Low-Income Housing Tax Credit (LIHTC) projects and 11,418 Multiple Listing Service (MLS) transactions in Virginia. Using hedonic regression analyses controlling for mediating factors, we find that the new construction of market-rate green certified houses is associated with small upfront costs but large and statistically significant price premiums. The construction of market-rate green certified houses has large and statistically significant spillover effects on existing non-certified houses. Existing non-certified affordable housing units show small and statistically insignificant negative price impacts on transactions of surrounding properties. The magnitude of social benefits associated with green building justifies the local provision of voluntary programs for green affordable housing where housing is expensive relative to its basic costs of production to promote sustainable development.

This paper details the evolution of access network sharing models from legacy DSL to the most recent fibre-based technology and the main challenges faced from a technical and business perspectives. We first give an overview of existing access sharing models, that span physical local loop unbundling and virtual unbundled local access. We then describe different types of optical access technologies and highlight how they support network sharing. Next, we examine how the concept of SDN and network virtualization has been pivotal in enabling the idea of “true multi-tenancy”, through the use of programmability, flexible architecture and resource isolation. We give examples of recent developments of cloud central office and OLT virtualization. Finally, we provide an insight into the role that novel business models, such as blockchain and smart contract technology, could play in 5G networks. We discuss how these might evolve, to provide flexibility and dynamic operations that are needed in the data and control planes.

We present organic, diamagnetic materials based on structurally simple (hetero-) tolane derivatives. They form crystalline thin-film aggregates that are suitable for Faraday rotation (FR) spectroscopy. The resulting new materials are characterized appropriately by common spectroscopic (NMR, UV-Vis), microscopy (POM), and XRD techniques. The spectroscopic studies give extremely high FR activities thus makes these materials promising candidates for future practical applications. Other than a proper explanation, we insist in the complexity of designing efficient FR materials starting off from single molecules.

Polyvinyl guanidineacetic (PVG) was prepared by the chemical grafting between poly(vinyl alcohol) (PVA) and guanidineacetic acid. The results showed that the guanidineacetic groups were successfully introduced into the polyvinyl alcohol by fourier transform infrared (FTIR) and thermogravimetry (TG). The effects of the amount of catalyst and reaction time on the PVG grafting rate were investigated. The PVG/NWF composite membrane as a heterogeneous catalyst for biodiesel production was successfully prepared by the solvent phase inversion. The effects of mass ratio of methanol/soybean oil and reaction temperature on the conversions using the composite membrane for transesterification were studied. And the reusability of the composite membrane and the kinetics of the reaction catalyzed by the composite membrane were also investigated. The conversions obtained from the model are in good agreement with the experimental data.

In this paper, we investigate the Hawking radiation process by using the quantum tunneling phenomenon of massive spin-1 (W-bosons) and spin-0 particles from (2+1) dimensional Black Hoke with quintessential and magnetic field. For this purpose, using Hamilton-Jacobi ansatz, we apply the WKB approximation to the field equations of massive charged vector particles. We get the required tunneling rate of radiated particles and obtain their corresponding Hawking temperature $T_h$. In order to study the quantum gravity effects, we utilize the generalized Proca and Klein-Gordan equations incorporating the generalized uncertainty principle (GUP) and recover the accompanying quantum corrected temperature $T'_{h}$.

Roaming complexity in terrains and unexpected environments poses significant difficulties in robotic exploration of an area. In a broader sense, robots have to face two common tasks during exploration namely walking on the drylands and swimming through the water. This research aims to design and develop an amphibious robot, which incorporates webbed duck feet design to walk on different terrains, swim in water and tackle obstructions on its way. The designed robot is compact and easy-to-use and also has the abilities to work autonomously. Such a mechanism is implemented by designing a novel robotic webbed foot consisting of two hinged plates. Due to the design, the webbed feet are able to open and close with the help of water pressure. The Klann linkage has been used to convert rotational motion to walking and swimming as an animal’s gait. Because of its amphibian nature, the designed robot can be used for exploring the tight caves, closed spaces and moving on uneven challenging terrains such as sand, mud or water. The presented model and design of the amphibious robot has been inspired by the working principle of duck feet. The propulsion generated through this feet system has been observed to be better and more controlled then the initial design and prototype of designed duck feet robot reported in [1]. The direction of movement can be managed, and the speed can be controlled using a larger contact area with water. Since duck is able to roam on both land and water, their feet movement during walking and swimming is adopted in designing the robot’s four legs. Klann linkage is used to mimic such duck feet motion and the control mechanism of the feet is driven by DC motors and DC servo motors which are governed by an Arduino microcontroller. The robot is capable of sensing the presence of water through conductive sensors and detects obstacles using ultrasonic sensor while walking. Due to its amphibian nature and other features in movement, the robot is capable of traversing diversified terrains. It is envisaged that the proposed design will be appreciated in the industry to design amphibious robots in near future.

Sustainability, as well as a concept related to a development model, is becoming a real guide to drive the governance choices of value chains. A sustainable policy has the objective of perpetuating production models over time while maintaining the environmental, economic and social dimensions that characterize a given production process. It is therefore important to measure the sustainability of a production system in its environmental, social and economic components and to understand the ongoing trends under the pressure of agricultural policies, market dynamics and innovation pattern introduced along the time in a production system. The purpose of the article is to assess the evolution of the level of sustainability of Parmigiano Reggiano production system under the effect of 20 years of innovation mechanism which impact on product quality, value chain performance and rural development. To this aim the paper discuss a holistic framework that allows the representation of stakeholder’s role considering the value chain and the territorial dimension. The paper discus also the use of dimensional indicators and propose a use of synthetic indexes to provide an overall picture of the evolution of sustainability of specific production system.

Assessment of drugs toxicity and associated biomarker genes is one of the most important tasks in the pre-clinical phase of drug development pipeline as well as in the toxicogenomic studies. There are few statistical methods for the assessment of doses of drugs (DDs) toxicity and their associated biomarker genes. However, these methods consume more time for computation of the model parameters using the EM (Expectation-Maximization) based iterative approaches. To overcome this problem, in this paper, an attempt is made to propose an alternative approach based on hierarchical clustering (HC) for the same purpose. There are several types of HC approaches whose performance depends on different similarity/distance measures. Therefore, we explored suitable combinations of distance measures and HC methods based on Japanese Toxicogenomics Project (TGP) datasets for better clustering/co-clustering between DDs and genes as well as to detect toxic DDs and their associated biomarker genes. We observed that Word’s HC method with each of Euclidean, Manhattan and Minkowski distance measures produces better clustering/co-clustering results. For an example, in case of glutathione metabolism pathway (GMP) dataset LOC100359539/Rrm2, Gpx6, RGD1562107, Gstm4, Gstm3, G6pd, Gsta5, Gclc, Mgst2, Gsr, Gpx2, Gclm, Gstp1, LOC100912604/Srm, Gstm4, Odc1, Gsr, Gss are the biomarker genes and Acetaminophen_Middle, Acetaminophen_High, Methapyrilene_High, Nitrofurazone_High, Nitrofurazone_Middle, Isoniazid_Middle, Isoniazid_High are their regulatory (associated) DDs explored by our proposed co-clustering algorithm based on the distance and HC method combination Euclidean: Word. Similarly, for the PPAR signaling pathway (PPAR-SP) dataset Cpt1a, Cyp8b1, Cyp4a3, Ehhadh, Plin5, Plin2, Fabp3, Me1, Fabp5, LOC100910385, Cpt2, Acaa1a, Cyp4a1, LOC100365047, Cpt1a, LOC100365047, Angptl4, Aqp7, Cpt1c, Cpt1b, Me1 are the biomarker genes and Aspirin_Low, Aspirin_Middle, Aspirin_High, Benzbromarone_Middle, Benzbromarone_High, Clofibrate_Middle, Clofibrate_High, WY14643_Low, WY14643_High, WY14643_Middle, Gemfibrozil_Middle, Gemfibrozil_High are their regulatory DDs. These results are validated by the available literature and functional annotation.

3D-printing with foam concrete, which is known for its distinct physical and mechanical properties, has not yet been purposefully investigated. The article at hand presents a methodological approach for the mixture design of 3D-printable foam concretes and a systematic investigation of the potential application of this type of material in digital construction. Three different foam concrete compositions with water-to-binder ratios between 0.33 and 0.36 and having densities of 1100 to 1580 kg/m³ in the fresh state were produced with a pre-foaming technique using a protein-based foaming agent. Based on the fresh-state tests, including 3D-printing as such, an optimum composition was identified and its compressive and flexural strengths were characterised. The printable foam concrete showed compressive strength above 10 MPa and low thermal conductivity, which make it suitable for 3D-printing applications, while fulfilling both load-carrying and insulating functions.

In this work the general problem of the characterization of the topological phase of an open quantum system is addressed. In particular, we study the topological properties of Kitaev chains and ladders under the perturbing effect of a current flux injected into the system using an external normal lead and derived from it via a superconducting electrode. After discussing the topological phase diagram of the isolated systems, using a scattering technique within the Bogoliubov-de Gennes formulation, we analyze the differential conductance properties of these topological devices as a function of all relevant model parameters. The relevant problem of implementing local spectroscopic measurements to characterize topological systems is also addressed by studying the system electrical response as a function of the position and the distance of the normal electrode (tip). The results show how the signatures of topological order affect the electrical response of the analyzed systems, a subset of such signatures being robust also against the effects of a moderate amount of disorder. The analysis of the internal modes of the nanodevices demonstrates that topological protection can be lost when quantum states of an initially isolated topological system are hybridized with those of the external reservoirs. The conclusions of this work could be useful in understanding the topological phases of nanowire-based mesoscopic devices.

Upland lakes (ULs) of the Carajás, southeastern Amazonia, have been intensively studied to their evolution during the Quaternary, as well as the development of the associated biota. In this review, several classical and modern approaches from structural geology to the pollen rain and sedimentary data which cover an area of around 41,300 km² were compiled. Multi-elemental geochemistry indicates that the detrital sediments derived from weathered crusts and soils, while the sedimentary organic matter represent autochthonous (siliceous sponge spicules, algae, macrophytes) and allochthonous (C3 plants and freshwater DOC) sources. Modern pollen rain suggests that even small lakes and canga areas can reflect forest signal, which depends on the topographic control and prevailing wind direction on pollen deposition. Integrated data of the sedimentary cores indicate that the active lakes never dried up during the last 50 ka cal BP. However, subaerial exposure occurs on filled lakes such as ST02 Lake during the LGM, LB3 and R2 lakes at the mid-Holocene due to drier paleoclimate conditions. Considering the organic proxies, only LB3 Lake presents expansion of C4 canga (montane savanna) plants since ULs of the Serra da Bocaína does not present siderites. Siderite formation on ULs deposits also points to drier paleoenviromental conditions, interrupting predominantly wet conditions. However, there is no evidence for widespread expansion of savanna into Southeastern Amazonia during the late Pleistocene and Holocene.

In this paper, we introduce a new class of Laguerre-based Hermite-Fubini numbers and polynomials and investigate some properties of these polynomials. We establish summation formulas of these polynomials by summation techniques series. Furthermore, we derive symmetric identities of Laguerre-based Hermite-Fubini numbers and polynomials by using generating functions.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

In this article, our main purpose is to establish a new extension of Mittag-Leffler function by using the known extended beta function $\mathbf{B}_{\omega}(a,b;p)$ introduced in [1]. It led to a novel extension of the applicability of Mittag-Leffler function that introduced them as distributions defined for a specific set of functions. We also, investigate some of its important properties, namely recursion relation, Mellin transform and differential formulas.