The effect of pH regulation on biohydrogen production was studied using suspended and immobilized mixed cultures. Four sets of experiments were conducted using suspended cells under regulated pH (Sus_R) and non-regulated pH conditions (Sus_N) as well as alginate-immobilized cells under pH regulated (Imm_R) and non-pH regulated conditions (Imm_N). Sus_R showed a peak hydrogen fraction of 44% and complete glucose degradation, compared to Sus_N with a peak hydrogen fraction of 36% and a glucose degradation of 37%. Imm_R experiments showed a peak biohydrogen fraction of 35%, while the peak hydrogen fraction observed with Imm_N was 22%. The highest hydrogen fraction was observed using suspended cells under regulated pH conditions. A 100% glucose degradation was observed in both pH regulated and non-regulated processes using immobilized cells. The rate of pH change was slower for immobilized cells compared to suspended cells suggesting a better buffering capacity under non pH regulated conditions. The study showed that biohydrogen production with suspended cells in a non-regulated pH environment resulted in early termination of the process and lower productivity.

The analysis of suspended particle size distribution in produced water for hydraulic fracturing and for water injection operations is vital for the effective development of tight reservoir formations like the Middle Bakken. Several reservoir engineering studies and industry guidelines recommend that particle sizes fall between 1/7th and 1/3rd of the square root of the formation permeability measured in millidarcies, to avoid pore throat clogging and subsequent formation damage. In the tight Bakken formation, with an average permeability of 0.04 millidarcies, the ideal particle size range for total suspended solids should fall within the 0.03 to 0.06 microns range. This study evaluates whether produced water used for hydraulic fracturing and enhanced oil recovery in the Middle Bakken meets this recommendation, as there are no established regulations in North Dakota addressing this issue. Using laser diffraction, particle size distribution was measured in treated and untreated produced water samples. The results show that current treatment methods do not reduce particle sizes to the recommended range. Treated water had particle diameters ranging from 8.5 to 40 μm, while untreated water had diameters ranging from 8.2 to 10 μm. None of the samples met the particle size requirements for safe use in hydraulic fracturing and water injection. This study highlights the inadequacy of current water recycling practices and offers empirical evidence that may guide future regulations on produced water reuse hydraulic fracturing and water injection in the Bakken.

Suspended and deposited sediments in streams can interfere with filter-feeding caddisfly larvae by reducing feeding sites and feeding efficiency, potentially lowering densities, growth rates, and secondary production of an important trout prey. We conducted field studies at multiple stream sites with differing suspended sediment loads, and a laboratory study conducted under controlled conditions, together designed to examine the role of suspended sediments in the population dynamics and behavior of Brachycentrus occidentalis (Trichoptera: Brachycentridae) larvae in a Minnesota, USA, trout stream. Stream sites that had elevated turbidities and suspended sediments also had significantly more fine bottom substrates and higher substrate embeddedness. In addition, Brachycentrus densities were reduced, growth rates were slower, secondary production was reduced, and overall benthic macroinvertebrate taxa richness was lowest at the site with the highest suspended sediment loading. Colder water temperatures at one site also influenced Brachycentrus production. In 24-hour laboratory studies conducted in recirculating aquaria, the feeding activities of Brachycentrus larvae were reduced and positioning altered under high turbidities (500 nephelometric turbidity units, NTU) relative to low turbidities (50 NTU or lower). High suspended sediment loads have adversely affected filter-feeding caddisfly larvae by embedding and burying preferred coarse feeding substrates, altering their feeding positions and movements during highest flows, and ultimately impacting densities, growth rates, and secondary production.

Spatiotemporal variations of sediments transported along rivers play a crucial role in a wide spectrum of uses, such as navigation, recreation, habitats or hydropower production. The advancement in technology has made it possible to use various indirect techniques to study and evaluate the transport of suspended sediment in fluvial environments. To investigate large-scale phenomena, remote sensing is becoming a largely utilized approach, as it allows to combine spatially-distributed and local information. Dam-induced sediment reduction occurs in large and small rivers worldwide, having profound implications on the fluvial systems. However, the systematic change of suspended sediment concentration (SSC) and its dynamic processes are not well known, and generally investigated only at the very local scale using field information. In this work, SSC maps were created by combining satellite images with local monitoring SSC data, using the Zhijiang -Chenglingji reach of the Changjiang River (China) as a case study, and analyzing how SSC dynamics changed over the period 2017-2022 in correspondence of extreme events. Multiple relationships between measured SSC and bands reflectance were tested, showing the potential of the best-performing one (R2=0.43) in mapping SSC spatiotemporal variations over an extent of dozens of kilometres, eventually providing new insights into the SSC dynamics at hotspots of the river systems, such as confluence zones, barriers, and reservoirs.

The intrinsic non-linearity and complexity of suspended sediment dynamics, which are impacted by the geographical variability of basin parameters and temporal climatic patterns, make it difficult to estimate suspended sediment concentration (SSC) accurately in hydrological processes. Deep neural networks (DNNs), a cutting-edge modeling method that can capture the innate non-linearity in hydrological systems, have emerged as a solution to this problem. Using primary data on discharge, SSC, and turbidity, the long short-term memory method of DNNs was employed in this study to simulate the discharge-suspended sediment connection for the Esopus Creek, NY, USA as the first objective. To develop effective modeling strategies, multiple scenarios of feature selection, including combinations of discharge, turbidity and SSC for preceding days, were considered. Secondly, the variations in SSC and discharge between the three USGS gages along Esopus Creek that were upper stream, lower stream, and downstream, adjacent to the pourpoint were analyzed. Statistical metrics and scenarios of feature importance were used to evaluate the effectiveness of the DNN-based models. The study shows that among 24 DNN approaches feature selection is crucial in simulating the daily SSC, and discharge and presenting novel research directions for utilizing machine learning algorithms in water quality.

In the article, were checked influences of microaeration, pH, and VSS (Volatile Suspended Solid) for sour cab-bage anaerobic digestion. Results fermentation of sour cabbage under the condition of small oxygen addition are presented in this research can be classified as dark fermentation or hydrogenotrophic anaerobic digestion. The investigations were carried out for two concentrations 5 g VSS /L and 10 g VSS /L of sour cabbage at pH 6.0. The oxygen flow rates (OFR) for 5 g VSS /L were in the range of 0.53 to 3.3 mL/h for obtaining 2% to 8% of oxygen. In cases of low pH and microaeration, ethylene production was observed at a level below 0.05% in biogas. The highest volume of hydrogen for 5 g VSS/L was obtained for flow rate 0.58 O2 mL/h, giving hydrogen concentration in biogas in the range of 0 to 20%. For VSS 5 g/L and oxygen flow rate 0.58 mL/h; 0.021 L of hydrogen is produced per gram of VSS. In this case, VSS 10 g/L and oxygen flow rate 1.4 mL/h at pH 6.0, 0.03 L of hydrogen is generated per gram. Microaeration from 0.58 mL/h to 0.87 mL/h was propitious for hydrogen production at 5 g VSS/L of sour cabbage and 1.4 mL/h for 10 g/L. Another relevant factor is the volatile suspended solid factor of sour cabbage that caused optimal hydrogen production at VSS 89.32%.

Wind is one of the factors that has a great influence on suspended matter in lakes, especially in shallow lagoons. In order to know how wind affects the water in Albufera of Valencia, a shallow coastal lagoon, the measured variables of turbidity and transparency have been correlated with the estimates by processing Sentinel-2 satellite images with the Sen2Cor processor. Data from four years of study show that most of them are light to gentle easterly breezes and moderate to fresh westerly breezes. The results obtained show significant correlations between the measured variables and those obtained from the satellite images for total suspended matter and water transparency and with the average daily wind speed. There is no significant correlation between wind and chlorophyll a. Moderate to fresh breezes resuspend the fine sediment reaching concentration values from 100 to 300 mg L-1 according to satellite data. However, it is necessary to obtain field data for the values of moderate and fresh winds, as for now there are no experimental data to verify the validity of the satellite estimates.

While the underwater submersible encounters internal solitary wave (ISW), its loadings and motions would be seriously disturbed. To investigate the interaction effect between the suspended submersible and ISW, a three dimensional ISW-submersible interaction numerical model was established based on the Computational Fluid Dynamics (CFD) method. The generation and propagation of ISW was simulated in a two-layer fluid numerical wave tank according to the eKdV theory. The standard operation equation of submersible was introduced to simulate the six degree of freedom (6DoF) motions of submersible combined with the overset dynamic mesh method. The motion simulation method of submersible was effectively validated by comparing with published experimental results on the motion responses of the slender body under the ISW. Based on the constructed numerical model, the dynamic mechanism between the suspended submersible and ISW were studied, and the effects of the initial submerged depths and the ISW amplitudes on the dynamic responses of the submersible were revealed. According to the numerical results, the motions of the submersible have been significantly determined by its initial submerged depths. The submersible located above the ISW interface has a significant motion along the propagation direction of ISW and its motion trajectory resembles a counterclockwise semi ellipse. The motions of the submersible located below the ISW interface follows with the trace of the lower layer fluid which presented as an unclosed clockwise ellipse. The corresponding motions of the submersible would be increased as the increase of the ISW amplitudes.

Concrete cracks have a detrimental effect on the strength properties and durability of the structures. So, repairing of concrete cracks to recover their strength parameters is more important task in civil engineering. To repair concrete cracks, MICP has been widely analysed in recent times; but, zero research is conducted to deeply investigate the repair effects of MICP on concrete cracks with rough surface by using the theoretic model. In current research, MICP with a novel mathematical model was attained by taking the precipitation of calcium carbonate (CaCO3), ureolysis, suspended biomass, geochemistry, transport of solute and biofilm growth. Furthermore, crack repair experiments were performed to check the workability of the new mathematical method. The outcomes revealed that the designed suspended biomass concentrations in cracks diminished step by step. The comparison in between the experimental results and calculated results verified the precision of migration behaviour of the suspended biomass. At the inlet, the solute concentrations and biofilm volume fractions was higher, causing in rise of yield amounts for calcium carbonate. The consumed solutes concentrations were higher for cracks of less rough surface, ultimately causing in smaller sonic time; and the values of sonic time for upper portions of cracks was smaller, showing good repair impacts. The recommended mathematical model provides a better tool that controls repair time and microbial metabolism process to report a new adjustive, bioremediation and biomineralization to concrete, which could provide a firm base for remediation of material in civil engineering field.

The dynamics of suspended sediment involves inherent non-linearity and complexity as a result of the presence of both spatial variability of the basin characteristics and temporal climatic patterns. As a result of this complexity, the conventional sediment rating curve (SRC) and other empirical methods produce inaccurate predictions. Deep neural networks (DNNs) have emerged as one of the advanced modeling techniques capable of addressing inherent non-linearity in hydrological processes over the last few decades. DNN algorithms are used to perform predictive analysis and investigate the interdependencies among the most pivotal water quantity and quality parameters i.e., discharge, suspended sediment concentration (SSC), and turbidity. In this study, the Long short-term memory (LSTM) algorithm of DNNs is used to model the discharge-suspended sediment relationship for the Stony Clove Creek. The simulations were run using primary data on discharge, SSC and turbidity. For the development of the DNN models and examining the effects of input vectors, combinations of different input vectors (namely discharge, and SSC) for the current and previous days are considered. Furthermore, a suitable modelling approach with an appropriate model input structure is suggested based on model performance indices for the training and testing phases. The performance of developed models is assessed using statistical indices such as root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). Statistically, the performance of DNN-based models in simulating the daily SSC performed well with observed sediment concentration series data. The study demonstrates the suitability of the DNN approach for simulation and estimation of daily SSC, opening up new research avenues for applying hybrid soft computing models in hydrology.

VNREDSat-1 is the first Vietnamese satellite allowing the survey of environmental parameters such as vegetation and water coverages, or surface water quality at medium spatial resolution (from 2.5 to 10 meters depending on the considered channel). The NAOMI sensor on board VNREDSat-1 has the required spectral bands to assess the suspended particulate matter concentration, SPM. Because recent studies have shown that the remote sensing reflectance, Rrs(), at the blue (450 – 520 nm), green (530 – 600 nm), and red (620 – 690 nm) spectral bands can be assessed from NAOMI with a good accuracy, the present study is dedicated to the development and validation of an algorithm (hereafter referred to as V1SPM) to assess SPM from Rrs() over inland and coastal waters of Vietnam. For that purpose, an in situ data set of hyper-spectral Rrs() and SPM (from 0.47 to 240.14 g.m-3) measurements collected at 205 coastal and inland stations has been gathered. Among the different approaches, including 4 historical algorithms, the polynomial algorithms involving the red-to-green reflectance ratio presents the best performance on the validation data set (MAPD of 18,7%). Compared to the use of a single spectral band, the band ratio allows to reduce the scatter around the polynomial fit as well as the impact of imperfect atmospheric corrections. Due to the lack of matchup data points with VNREDSat-1, the full VNREDSat-1 processing chain (RED-NIR and V1SPM) aiming at estimate SPM from the top-of-atmosphere signal has been applied to the Landsat-8/OLI match-up data points with relatively low to moderate SPM concentration (3.33-15.25 g.m-3) showing a MAPD of 15,8%. An illustration of the use of this VNREDSat-1 processing chain during a flooding event occurring in Vietnam is provided.

In the context of freshwater ecosystems, turbidity and suspended solids play crucial roles, with their levels significantly influenced by anthropogenic activities. This study focuses on assessing and monitoring these parameters in Albufera de Valencia using Sentinel-2 imagery. The primary aim is to establish reliable estimation algorithms that can contribute to effective ecosystem management. The study calibrated and validated algorithms for estimating turbidity and suspended solids. The R783×R705/R490 model proved to have the best performance for estimating turbidity and total solids in the Albufera. However, R783/R490 obtained a higher coefficient of de-termination for the organic part, while the R705 band was selected for the inorganic part. However, to achieve better estimates of turbidity and inorganic matter, more research is needed in the future. The implications of excessive suspended solids are underscored, including the depletion of dissolved oxygen, and reduced primary productivity due to limited light penetration and habitat availability. Collaboration between disciplines such as limnology, optics and water chemistry are crucial to advance water quality estimation models in lakes and lagoons such as Albufera. By integrating expertise and approaches from these diverse fields, new knowledge can be gained and the basis for more effective management and conservation strategies can be laid.

Artificial membrane systems can serve as models to investigate molecular mechanisms of different cellular processes, including transport, pore formation, and viral fusion. However, the current simulacrums such as SUVs, GUVs, and the supported lipid bilayers suffer from issues, namely high curvature, heterogeneity, and surface artefacts, respectively. Freestanding membranes provide a facile solution to these issues, but current systems developed by various groups use silicon or aluminium oxide wafers for fabrication that involves access to a dedicated nanolithography facility and high cost while conferring poor membrane stability. Here, we report the development, characterization and applications of an easy-to-fabricate suspended lipid bilayer (SULB) membrane platform leveraging commercial track-etched porous filters (PCTE) with defined microwell size. Our SULB system offers a platform to study the lipid composition-dependent structural and functional properties of membranes with exceptional stability in a high throughput fashion. With dye entrapped in PCTE microwells by SULB, we show that sphingomyelin significantly augments the activity of pore-forming toxin, Cytolysin A (ClyA) and the pore formation induces lipid exchange between the bilayer leaflets. Further, we demonstrate high efficiency and rapid kinetics of membrane fusion by dengue virus in our SULB platform. Our suspended bilayer membrane mimetic offers a novel platform to investigate a large class of biomembrane interactions and processes.

Because of the widespread use of bisphenol analogues (BPs) as the alternatives to bisphenol A (BPA), they have attracted considerable attention for health risk in aquatic ecosystems. The occurrence and distribution of six BPs were researched in soluble phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. Except for bisphenol Z, all BPs were detected in the two or three phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the soluble phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the soluble and colloidal phases, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude higher than SPM, suggesting that colloids have an obvious impact on regulating BPs’ environmental behaviors. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

Owing to the widespread use of bisphenol analogues (BPs) as bisphenol A (BPA) alternatives, they have been recognized to constitute a health risk for aquatic ecosystems. The occurrence and distribution of six BPs were investigated in the truly dissolved phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. With the exception of bisphenol Z, all BPs were detected in at least two phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the truly dissolved phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the truly dissolved phase and colloidal phase, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude greater than that of SPM, suggesting that colloids play an important role in regulating the environmental behaviors of BPs. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

Artisanal and Small-scale Gold Mining (ASGM) has caused several environmental impacts, resulting in significant siltation of water bodies due to the deposition of sediments on river banks. Based on this perspective, this study aims to investigate the water bodies and regions most impacted by mining activities, especially in relation to the increase in the Total Suspended Solids (TSS) caused by ASGM, focusing on the territories of Suriname and French Guiana, over the period from 2017 to 2023, through the creation of an algorithm in Google Earth Engine. The research also aims to map and describe active mining in this region using the Classification and Regression Tree (CART) method, which achieved an overall accuracy of 82% and a kappa index of 0.77. The results reveal that from 2017 to 2024 there was an increase of 148.09 km² of mining, with an average increase in TSS of up to 167 mg/l in water bodies most affected by mining activities. Finally, the continued importance of using remote sensing technologies, such as GEE, together with innovative methodological approaches, to monitor and manage natural resources in a sustainable manner is highlighted.

Urban stormwater runoff from a medium-density residential development in southeast Queensland has been monitored in the field since November 2013. A treatment train installed on the site includes rainwater tanks collecting roofwater, 200-micron mesh baskets installed in grated gully pits and two 850 mm high media filtration cartridges installed in an underground 4 m³ vault. A monitoring protocol developed by research partners, Queensland University of Technology (QUT), guided the monitoring process over a 4.5-year period. Heavy metals were included in the list of analytes during the monitoring period as the catchment is within 1 km of the environmentally-sensitive Moreton Bay, Queensland. Removal efficiencies observed at this site for the regulated pollutants; total suspended solids (TSS), total phosphorus (TP) and total nitrogen (TN) for the pit baskets were 61%, 28% and 45% respectively. The cartridge filters removed 78% TSS, 59% TP, 42% TN, 40% total copper and 51% total zinc. As the measured influent concentrations to the cartridge filters were low when compared to industry guidelines, the dataset was merged with international field results for TSS (n=39) and TP (n=32) but truncated within anticipated guideline levels. The combined dataset for the media filter demonstrates performance at 89% TSS, 66% TP and 42% TN. The total gross pollutant generation rate from the medium-density residential catchment was observed to be 0.24 m³/Ha/year, with a corresponding air-dried mass of 142.5 kg/Ha/year. Less than 2% of the gross pollutant mass was anthropogenic. The findings of this research suggest that the treatment train, and in particular the media filter, holds promise for the removal of total copper and total zinc, in addition to TSS, TP and TN, from urban stormwater runoff. Based on a maximum, low risk trigger TN concentration of 1.5 mg/L, the field test data from 4.5 years of operation and standard maintenance, suggests a 5.5-year replacement interval for the media filters.

A three-dimensional, unstructured grid, hydrodynamic and suspended-sediment transport model (i.e., SELFE-SED) was developed to simulate temporal and spatial variations of suspended sediment and was applied to the subtropical subalpine Tsuei-Feng Lake (TFL) of Taiwan. The model was validated with measured water level and suspended‑sediment concentration in 2009, 2010, and 2011. The overall model simulation results are in quantitative agreement with the observational data. The validated model was then applied to explore the most important parameter that affects the suspended-sediment concentration and to investigate the effect of wind stress on the mean current and suspended‑sediment distribution in this shallow lake. Modeling results of sensitivity analysis reveal that the settling velocity is a crucial parameter and erosion rate is less important in the suspended-sediment transport model. Remarkable lake circulation was found based on the strength of wind speed and wind direction. Strong wind would result in higher mean current in the top layer and suspended-sediment distribution in the top and bottom layers. This study demonstrated that the wind stress played a significant influence on mean circulation and suspended-sediment transport in a shallow lake.

The Suspended soils (which are also called canopy soil), associated with epiphytic plants in tropical forest canopies, have a very special type of biological cycle, morphological organization and ecological functional role. To date, only some features of these soils have been described for certain sectors of the tropics, in particular Southeast Asia. It was studies out whether the chemical composition and hydrological parameters depend significantly on the genesis of suspended soil, or they represent a single soil phenomenon with a certain supposed ecosystem function. Suspended soils are characterized by average values of hygroscopic moisture comparable with mineral soils. At the same time the maximum water holding capacity and field moisture capacity reaches hundreds and even thousands of percent which cannot but lead to mesophilization of the microclimate of the near-stem environments. In any case suspended soils are characterized by 4-10 higher values of hydrologic properties than mineral terrestrial soils of the same landscapes. The carbon content in suspended soil materials varied widely and was comparable with that of tropical forest litter and boreal peatlands . At the same time, tropical suspended soils are characterized by very low nitrogen content, which is reflected in very high carbon-to-nitrogen ratios. Such a values are typical of peats and forest litter and indicates a very low degree of humification of organic matter. Soil pH values tends to the acidic, and more often very acidic range. This corresponds well to the low content of labile forms of calcium and magnesium and corresponds to the oligotrophy of the soils. The content of mobile forms of phosphorus, potassium and ammonium nitrogen is extremely high in suspended soils. The high content of nutrients in tropical suspended soils is enormously high compared to forest soils of other climatic zones and should be noted as their most important attributive characteristic. Taking into account the high accumulative-sorption capacity of suspended soils, the low content of heavy metals in them indicates the absence of modern aerotechnogenic pollution of all the studied ecosystems. Thus, we are talking about a certain deficiency of heavy metals in the eluvial ecosystem of the tropical rain forest. This once again confirms the hypothesis that the essence of epiphytic soil formation was and is that the biotic cycle breaks away from the ground and moves evolutionarily into the middle and upper tiers of the tropical rainforest ecosystem. Tree trunks in this context represent vertically and subhorizontally oriented phase interfaces, similar to parent materials, and epiphytic soils are analogues of peat accumulations with extremely high water-holding capacity, which is of extremely important environmental significance.

This study investigated the content of macro- and microelements in the lower reaches of the Ob River (Western Siberia). Seasonal sampling was performed over a four-year period (2020-2023) during the main hydrological seasons (winter low water, spring-summer floods, and early fall low water) at three river stations. Suspended and dissolved fractions were separated by filtration through 0.45-micron nitrocellulose filters. The results revealed significant seasonal variations in the elemental content of the Ob River water, associated with changes in catchment inputs, physical and chemical conditions of the aquatic environment, and the amount and composition of incoming suspended sediment. During high water flow events in the Ob River, the concentration of suspended solids increased substantially. These included significant quantities of sparingly soluble hydrolysates such as Al, Ti, Zr, Ga. During the winter period when the Ob River was ice-covered, a 2- to 3-fold rise was observed in the concentration of Na, Mg, Ca, K, Si, Mn. Having accounted for these seasonal variations in water chemistry, we were able to refine our estimates of elemental export to the Arctic Ocean. Compared to estimates from previous studies, we observed with 2.3-fold higher dissolved loads of Mn, 2.1-fold for Zn, 1.6-fold for Fe, and 1.4-fold for Pb.

Easy to use satellite-based water quality visualizations are needed for monitoring and understanding coastal and inland waters, but to date, no publicly accessible real-time global visualization system was in place. Here we introduce the Ulyssys Water Quality Viewer (UWQV), a Sentinel Hub EO Browser Custom script designed for qualitative views of aquatic chlorophyll and suspended sediment concentrations. The viewer avoids unmixing of the chlorophyll and suspended sediment spectral signal by visualizing these parameters together, with high concentrations of suspended sediment obscuring chlorophyll if present. Cloud masking uses the Hollstein and Braaten algorithms (existing EO Browser custom script code), additionally water surfaces are masked using the Normalized Differential Water Index. Chlorophyll is estimated using reflectance line height-based indicators such as fluorescence line height and maximum chlorophyll index. Suspended sediment is visualized based on single-band reflectances at 620 or 700 nm. Data sources are Sentinel-2 and Sentinel-3 images, allowing either 20 m spatial resolution or up to daily imaging. This visualization system is easy to operate and interpret, and combined with the data service capacity of the Sentinel Hub, it is expected that UWQV will contribute to monitoring of remote water bodies and to our overall understanding of physical limnology and aquatic ecology.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

Effective discharge, which represents the flow, or range of flows, that transport the most sediment over long term, was determined based on the mean daily flow discharge and mean daily suspended sediment discharge recorded between 1994 and 2014 at four gauging stations along the Trotuș River. This study proposes an efficient method for the estimation of effective discharge based on observed values of the suspended sediment load. By employing this method the suspended sediment load is no longer either under- or overestimated as in the cases when the assessment is based on sediment rating curves. The assessment on effective discharge was performed at two distinct levels: for the entire data series during the investigated time spans and, subsequently, for flows less than the bankfull discharge. The effectiveness curves of the suspended sediment transport characteristics revealed highly multimodal characteristics with many peaks, indicating ample ranges for the effective discharges. The main effective discharge corresponded to large flood events, which are typical for the upper end of the discharge range, whereas the secondary effective discharges corresponded to sub-bankfull flows, which are more frequent. The changes that occurred in the channel bed are reflected by the temporal variations in the effective discharge.

This paper is about to estimate the suspended sediment transport amount in the streams flowing into the Sapanca Lake Basin. There are 12 subsidiary streams flowing into the Sapanca Lake Basin. With the aim of estimating the suspended sediment transport in 2012-204 in these subsidiary streams, measurements belonging the parameters such as level, cross sectioning, flow rate, temperature and suspended sediment were made monthly. Along the measurement period, weather conditions were above seasonal normal and precipitations decreased. In order to estimate the suspended sediment amount by using results of the measurement obtained, Artificial Neuron Network (ANN), Sediment Rating Curve (SRC) and Multiple Linear Regression (MLR) models were used for different scenarios. It was seen that artificial neuron networks yielded the most accurate results among the models.

Stormwater management is especially critical for urbanized landscapes that border surface waters and therefore must be monitored accurately to meet permitting requirements and mitigate environmental impact. To assess the impact of stormwater pollutants from the university grounds of a large midwestern campus, we pursued the following two objectives. First, to empirically quantify the concentration of four pollutants in campus stormwater (total suspended solids (TSS), total phosphorus (TP), total Kjeldahl nitrogen (TKN), and chlorides (Cl-)) and compare these observations to international averages and modeled values from the Source Loading and Management Model for Windows (WinSLAMM v10.5.0), used by the university for stormwater monitoring. And second, we sought to quantify the steady state infiltration rate of two porous pavements (concrete and asphalt), and two concrete porous paver surfaces (with interlocking aggregates and without) constructed by the university to mitigate environmental impact. Results showed low TSS concentrations relative to other municipalities and modeled results. The discrepancy between modeled and empirical values is argued to arise from spatial and temporal constraints of sampling. Conversely, concentrations of TP, TKN, and Cl-, were at similar levels to reference areas and WinSLAMM, with TP and TKN likely sourced from mainly organic, non-particulate sources (e.g. leaf litter). Of the four mitigation systems, the porous pavers with aggregates had the highest infiltration rate compared to the other three porous pavements, although compounding factors such as age and landcover may have influenced performance differences.

The monitoring of coastal waters using satellite data, from sensors including Sentinel-3 OLCI, has become a vital tool in the management of these water environments; especially when it comes to improving our understanding of the effects of climate change on these regions. In this study, Level-2 water products derived from different OLCI Sentinel-3 processors were validated against a comprehensive in situ dataset from the NW Baltic Sea proper region. The products validated were those of the regionally adapted Case-2 Regional Coast Colour (C2RCC) OLCI processor (v1.0 and v2.1), as well as the latest standard Level-2 OLCI case 2 (Neural Network) products from Sentinel-3’s processing baseline: Baseline Collection 003 (BC003), including “CHL_NN”, “TSM_NN”, and “ADG443_NN”. Furthermore, the effect of the current EUMETSAT system vicarious calibration (SVC) on the Level-2 water products was also validated. Results showed that the system vicarious calibration (SVC) reduces the reliability of the Level-2 OLCI products. For example, the application of these SVC gains to the OLCI data for the regionally adapted v2.1 C2RCC products resulted in RMSD increases of 36% for “conc_tsm”; 118% for “conc_chl”; 33% for “iop_agelb”; 50% for “iop_adg”; and 10% for “kd_z90max” using a ±3h validation window. The findings indicate that the current EUMETSAT SVC gains should be applied and interpreted with caution in the region of study at present. A key outcome of the paper recommends the development of a regionally specific SVC against AERONET-OC data for the region.

The optical complexity of coastal waters is mostly caused by the water discharged from land carrying optical components (such as dissolved and particulate matter) into coastal bays and estuaries, and increasing the attenuation of light. This paper aims to investigate the links between in-water optical properties in four Swedish bays (from the northern Baltic proper up to the Bothnian bay) and the land use and land cover (LULC) and the hydrology in the respective catchment of each bay. The optical properties were measured in situ over the last two decades by various research and monitoring groups while the LULC in each bay was classified using the Copernicus Land Monitoring Service based on Landsat 8 and Sentinel-3 data. The absorption coefficient of coloured dissolve organic matter at 440 nm, aCDOM (440), and its spectral slope factor, SCDOM, were mostly correlated to natural land cover classes (Wetland, Meadow) acting as sources of CDOM, while Agricultural and Urban classes seem to act as sinks. The Agricultural class was also found to be a sink for suspended particulate organic matter (SPOM) whilst Coniferous and Mixed Forests as well as Meadows acted as a sources. SPOM seems to mostly originate from Natural classes, possibly due to the release of pollen and other organic matter. Overall, the methods applied here allow for a better understanding of effects of land used and land cover on the bio-optical properties, and thus coastal water quality, on a macroscopic scale.