A novel configuration for a super-wide impedance planar antenna is presented based on a 2 × 2 microstrip patch antenna (MPA). The antenna comprises a symmetrical arrangement of four-square patches that are interconnected to each other with cross-shaped high impedance microstrip lines. The antenna array is exciting through a single feedline connected to one of the patches. The proposed antenna array configuration overcomes the main drawback of conventional MPA of narrow bandwidth that is typically <5%. The antenna exhibits a super-wide frequency bandwidth from 20 GHz to 120 GHz for S₁₁<−15 dB, which corresponds to a fractional bandwidth of 142.85%. The antenna’s performance of bandwidth, impedance match, and radiation gain were enhanced by etching slots on the patches. The slotted microstrip patch essentially acts like a left-handed capacitance to exhibit metamaterial properties over a given frequency range. With the inclusion of the slot the maximum radiation gain and efficiency of the MPA have increased to 15.11 dBi and 85.79% at 80 GHz, which show an improvement of 2.58 dBi and 12.54%, respectively. The dimension of each patch antenna is 30 × 30 mm². The results show that the proposed MPA is useful for various communications existing and emerging systems such as ultra-wideband (UWB) communications, RFID systems, massive multiple-output multiple-input (MIMO) for 5G, and radar systems.

A novel quasi-twisted miniaturized wideband Branch Line Coupler (BLC) is proposed. The design is based on bisecting the conventional microstrip line BLC transversely and folding bisected sections on double-layered substrates with a common ground plane in between. The pair of quarter wavelength horizontal parallel arms is converted to a Z-shape meandered microstrip line in the designed structure. On the other hand, the pair of quarter wavelength vertical arms are cut by half into two lines and converted to a periodically loaded slow wave structure. The bisected parts of BLC are placed on the opposite side of the doubled-layer substrate and connected through four vias passing through the common ground plane. This technique enabled a compact BLC size of 6.4×18 mm2, which corresponds to a surface area miniaturization by ~50% as compared to the classical BLC size of 10×23 mm2 at 6GHz, Moreover, the attained relative bandwidth is 73.9% (4.6-10 GHz) for S11, and 75.8% (4.5-10 GHz) for S33 as compared to 41% for the ordinary BLC at the same resonant frequency. The circuit is constructed on a double-layered low-cost FR4 substrate with a relative permittivity of 4.3, and a loss tangent of 0.025. An isolation of -13dB was realized in both S13 and S31 demonstrating an excellent performance. The transmission coefficients between input/output ports S21, S41, S23, and S43 are between -3.1dB to -3.5dB at the frequency of 6GHz. Finally, the proposed BLC provides phase differences between output ports of 90.5o and 94.8o at the frequency of 6GHz when the input ports 1 and 3 are excited, respectively. The presented design offers the potential of being utilized as a unit cell for building a Butler-matrix (BM) for sub-6GHz 5G beamforming networks.

Load transfer through orthopaedic joint implants is poorly understood. The longer-term outcomes of these implants are just starting to be studied, making it imperative to monitor contact loads across the entire joint implant interface to elucidate the force transmission and distribution mechanisms exhibited by these implants in service. This study proposes and demonstrates the design, implementation, and characterization of a 3D-printed smart polymer sensor array using conductive polyaniline (PANI) structures embedded within a polymeric parent phase. The piezoresistive characteristics of PANI were studied to characterize the sensing behaviours inherent to these embedded pressure sensor arrays. PANI's stable response to a continuous load, its stability throughout loading and unloading cycles, and its repeatable and linear response to incremental loading cycles together with the accuracy of these measurements were investigated. It is demonstrated that this specially developed multi-material additive manufacturing process for polyaniline is an attractive approach for the fabrication of implant components having embedded smart-polymer sensors for the measurement and analysis of joint loads in orthopaedic implants.

Detecting, tracking, and classifying unmanned aerial vehicles (UAVs) in a swarm presents significant challenges due to their small and diverse radar cross-sections, multiple flight altitudes, velocities, and close trajectories. To overcome these challenges, adjustments of the radar parameters and/or position of the radar (for airborne platforms) are often required during runtime. The runtime adjustments help to overcome the anomalies in the detection, tracking, and classification of UAVs. The runtime adjustments are performed either manually or through fixed algorithms, each of which can have its limitations for complex and dynamic scenarios. In this work, we propose the use of multi-agent reinforcement learning (RL) to carry out the runtime adjustment of the radar parameters and position of the radar platform. The radar used in our work is a multibeam multifunction phased array radar (MMPAR) placed onboard UAVs. The simulations show the cognitive adjustment of the MMPAR parameters and position of the airborne platform using RL helps to overcome anomalies in the detection, tracking, and classification of UAVs in a swarm. A comparison with other artificial intelligence (AI) algorithms shows that RL performs better due to runtime learning of the environment through rewards.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.

5G low-earth orbit satellite communications offer enhanced wireless coverage beyond the reach of 5G terrestrial networks, with important implications, particularly for automated and connected vehicles. Such wireless automotive mass-market applications demand well-designed compact user equipment antenna terminals offering non-terrestrial jointly with terrestrial communications. The antenna should be low-profile, conformal, and meet specific parameter values for gain and operational frequency bandwidth, tailored to the intended applications, in line with the aesthetic design requirements of passenger cars. This work presents an original concept for a dual-band nested circularly polarized automotive user terminal that operates at the S-band frequencies around 3.5 GHz and Ka-band frequencies around 28 GHz, namely within the 5G new-radio bands n78 and n257, respectively. The proposed terminal is designed to be integrated into the plastic components of a passenger vehicle. The arrays consist of 2×2 aperture-coupled corner-truncated microstrip slot patch antenna elements for the n78 band and of 4×4 single-layer edge-truncated microstrip circular slot patch antenna elements for the n257 band. The embedded arrays offer, across the two bands, respectively 9.9 and 13.7 dBi measured realized gain and 3-dB axial ratio bandwidths of 100 and 1500 MHz for the n78 and n257 bands along the broadside direction. Detailed link budget calculations anticipate uplink data rates of 21 and 6 Mbit/s, respectively, deeming it suitable for various automotive mobility and internet-of-things applications.

In order to enhance the gain of antenna suitable for the airplane mounted platform, a conformal tightly coupled antenna array is investigated in this paper. Especially, three-dimensional (3-D) inkjet printing technique is used to implement the conformal property. The printing of antenna substrate and radiation layer is implemented by combining the fused deposition modelling and microdroplet injection molding technologies based on the existing 3-D printer. Here, through a unique combination of 3-D and 2-D inkjet printing of dielectric material and metallic ink, respectively, we demonstrate a monolithically integrated to a nonplanar antenna for the first time. Antenna measurements show that the complete characterization of this new process in terms of minimum feature sizes and achievable conductivities. This antenna configuration offers a high-gain performance with low-cost and rapid fabrication technique by using 3-D printing. The voltage standing wave ratio and radiation patterns are tested after adding the newly designed feed structure. Results shown the design process much efficient. Both antenna element and the array with good properties, which are in very good agreement with the specially mounted platform.

Wireless power transfer promises to revolutionize the way we use and power mobile devices. However, low transfer efficiencies prevent this technology from seeing wide scale real-world adoption. The aim of this work is to use quasioptics to develop a system composed of a dielectric lens fed by a phased array to reduce spillover losses, increasing the beam efficiency, while working on the antenna system’s Fresnel zone. The DC-RF electronics, digital beamforming and beam-steering by an FPGA, and radiating 4x4 microstrip patch phased array have been developed and experimented upon, while the lens has been designed and simulated. This paper details these preliminary results, where the phased array radiation pattern was measured, showing that the beam is being generated and steered as expected, prompting the lens construction for the complete system experimentation.

The ability to monitor Sprained Ankle Rehabilitation Exercises (SPAREs) in home environments can help therapists to ascertain if exercises have been performed as prescribed. Whilst wearable devices have been shown to provide advantages such as high accuracy and precision during monitoring activities, disadvantages such as limited battery life, users' inability to remember to charge and wear the devices are often the challenges for their usage. Also, video cameras, which are notable for high frame rates and granularity, are not privacy-friendly. This paper, therefore, proposes the use and fusion of unobtrusive and privacy-friendly sensing solutions for data collection and processing during SPAREs in home environments. Two Infrared Thermopile Array (ITA-32) thermal sensors and two Frequency Modulated Continuous Wave (FMCW) Radar sensors were used to simultaneously monitor 15 healthy participants during SPAREs which involved twisting their ankle in 4-fundamental movement patterns namely (i) extension, (ii) flexion, (iii) eversion and (iv) inversion. Experimental results indicated the ability to identify thermal blobs of participants performing the 4 fundamental movement patterns of the human ankle. Cluster-based analysis of data gleaned from the ITA-32 sensors and the FMCW Radar sensors indicated average classification accuracy of 96.9% with K-Nearest Neighbours, Neural Network, AdaBoost, Decision Tree, Stochastic Gradient Descent and Support Vector Machine, amongst others.

IoT system becomes hot topic nowadays for smart home, IoT helps devices to communicate together without human intervention inside home, so it is offering many challenges. A new smart home IoT platform powered using electromagnetic energy harvesting is proposed in this paper. It contains a high gain transmitted antenna array and efficient circular polarized array rectenna system to harvest enough power from any direction to increase life time of the batteries used in IoT system. Optimized energy consumption, the software with adopting the Zigbee protocol of the sensor node and low power microcontroller are used to operate in lower power modes. The proposed system has an 84.6 days lifetime which is approximately 10 times the lifetime for similar system. On the other hand, the proposed power management circuit operated at 0.3 V DC to boost the voltage to ~3.7V from radio frequency energy harvesting and manage battery level to increase the batteries lifetime. A predictive indoor environment monitoring system is designed based on a novel hybrid system to provide a non-static plan, approve energy consumption and avoiding failure of sensor nodes in smart home.

A fundamental aspect in the evolution of Time-to-Digital Converters (TDCs) implemented within Field-Programmable Gate Arrays (FPGAs), given the increasing demand for detection channels, is the optimization of resource utilization. This study reviews the principal methodologies employed for implementing low-resource TDCs in FPGAs. It outlines the foundational architectures and interpolation techniques utilized to bolster TDC performances without unduly burdening resource consumption. Low-resource Tapped Delay Line, Vernier Ring Oscillator, and Multi-Phase Shift Counter TDCs, including the use of SerDes, are reviewed. Additionally, novel low-resource architectures are scrutinized, including Counter Gray Oscillator TDCs and interpolation expansions using Voltage-Temperature-Consumption stable IODELAYS. Furthermore, the advantages and limitations of each approach are critically assessed, with particular emphasis on resolution, precision, non-linearities, and, especially, resource utilization. A comprehensive summary table encapsulating existing works on low-resource TDCs is provided, offering a comprehensive overview of the advancements in the field.

HIV-associated neurocognitive disorders (HAND) persist under antiretroviral therapy as a complex pathology that has been difficult to study in cellular and animal models. Therefore, we generated an ex vivo human brain slice model of HIV-1 infection from surgically resected adult brain tissue. Brain slice cultures processed for flow cytometry showed >90% viability of dissoci-ated cells within the first three weeks in vitro, with parallel detection of astrocyte, myeloid, and neuronal populations. Neurons within brain slices showed stable dendritic spine density and mature spine morphologies in the first weeks in culture, and they generated detectable activity in multi-electrode arrays. We infected cultured brain slices using patient-matched CD4+ T-cells or monocyte-derived macrophages (MDMs) that were exposed to a GFP-expressing R5-tropic HIV-1 in vitro. Infected slice cultures expressed viral RNA and developed a spreading infection up to 9-days post-infection, which were significantly decreased by antiretrovirals. We also detected infected myeloid cells and astrocytes within slices and observed minimal effect on cellular via-bility over time. Overall, this human-centered model offers a promising resource to study the cel-lular mechanisms contributing to HAND (including antiretroviral toxicity, substance use, and aging), infection of resident brain cells, and new neuroprotective therapeutics.

This paper presents a new approach to suppress interference between neighbouring radiating elements resulting from surface wave currents. The proposed technique will enable the realization of low-profile implementation of highly dense antenna configuration necessary in SAR and MIMO communication systems. Unlike other conventional techniques of mutual coupling suppression where decoupling slab is located between the radiating antennas the proposed technique is simpler and only requires embedding linear slots near the periphery of the patch. Attributes of this technique are (i) significant improvement in the maximum isolation between the adjacent antennas by 26.7 dB in X-band, & >15 dB in Ku and K-bands; (ii) reduction in edge-to-edge gap between antennas to 10 mm (0.37λ); and (iii) improvement in gain by >40% over certain angular directions, which varies between 4.5 dBi to 8.2 dBi. The proposed technique is simple to implement at low-cost.

The extensive use of engineered nanoparticles (ENPs) such as zinc oxide nanoparticles (ZnO NPs) in various commercial fields has spurred significant concern about its possible toxicological effects of ZnO NPs on human health and eco-system. Therefore, it is substantial to understand the aggregation phenomena which could attenuate this effect. This data article provides information on aggregation of ZnO NPs under the influence of various parameters of water chemistry. Moreover, Taguchi orthogonal array L27(313) design matrix was used to evaluate the effect of multiple parameters in aqueous solution. The data were obtained from single beam UV-Vis spectrophotometer (Optizen 2120 UV, Mecasys, Korea) using Optizenview 4.2.5 PC interference software, Fourier transform infrared spectrometer (FT/IR-4700, spectroscopy, JASCO Analytical Instruments, Easton, USA) and particle electrophoresis (NanoZS, Zetasizer, Malvern Instruments Ltd, Worcestershire, UK). The dataset draws attention on dominant parameters influencing aggregation of ZnO NPs in water. The analysis of variance (ANOVA) data revealed that electrolyte concentration, type and natural organic matter (NOM) concentration were the most significant parameters. Furthermore, FT-IR data presents a possible mechanism of ZnO NPs stabilization in the presence of different NOM. This data will be helpful for the development of environmental risk assessment strategies and prediction of fate and mobility of other ENPs in the aquatic environment.

This paper aims to present a smart high speed battery charger, powered by a photovoltaic module array, for a LiFePO4 battery as a solar energy storage device. With a battery charging strategy, the presented battery charger involves a Buck converter as the core equipped with a simple maximum power point (MPP) tracker. Considering complexity reduction and easy hardware implementation, a constant voltage MPP tracking approach is adopted such that the maximum amount of output power can be delivered to the load in response to an arbitrary change in the solar radiation. A smart two-stage charging strategy, with a constant current mode followed by a constant voltage mode, is employed in such a way that the battery charge process can be accelerated largely, while the damage caused by overcharging can be prevented. In the end, the performance of this proposal is validated experimentally.

We are introducing a highly efficient 48-channel ultrasound beamforming system ideal for ultrasound endoscopy applications. The system includes a transmitter and a receiver, which allow for low-area, high-resolution imaging acquisition. The transmitter uses a charge redistribution HV (high voltage) scheme to generate three-level pulses that actuate the transducer, implemented with the standard CMOS process for optimal cost and power savings. Meanwhile, the receiver features a sub-array structure and a delay generator that reduces area usage. To achieve high-resolution ultrasound imaging acquisition with low computational power, we developed the Shift Coherence Factor (SCF) algorithm, which is hardware-friendly. This approach delivers a lateral resolution over 20% better than the conventional delay and sum (DAS) algorithm, with a contrast ratio of over 30 dB. The system was implemented in a 180 nm standard CMOS process with an area of 24.98 mm2, power consumption of 8.23 mW per channel, achieving a delay resolution of 8.33 ns, and a low-area implementation of 0.52 mm2 per channel. The system offers high-quality imaging acquisition with minimal additional area and power consumption, which has great potential for 3D imaging or catheterized ultrasound systems.

Iterative Stochastic decoding is an alternative to standard fixed-point decoding of Low-density parity check codes (LDPC) to reduce inter-node routing. In this paper, we propose a Flexible Field-Programmable Gate Array (FPGA)-Based Stochastic decoding (SD) hardware architecture for LDPC codes in the Fifth-Generation (5G) New Radio (NR) Standard that supports decoding of set of various code rates. This decoder’s runtime flexibility is desirable to switch a better performing code rate automatically based on the channel conditions without the extra time needed for reprogramming of FPGA. An offline design method is implemented to generate the hardware description language (HDL) code description of the decoder for the required code-rate set, which is further synthesized and integrated into the Xilinx Kintex-7 series FPGA board to determine the hardware resource utilisation and processing throughput. The Synopsys design tools were employed during both the simulation and synthesis stages, in combination with TSMC 65-nm CMOS standard cell technology, to facilitate comparative analysis. Compared with state-of-the-art designs, the proposed architecture reduces hardware utilization by up to 26% and achieved energy efficiency by 52%.

DNA origami has emerged in recent years as a powerful technique for designing and building 2D and 3D nanostructures. While the breadth of structures that have been produced is impressive, one of the remaining challenges, especially for DNA origami structures intended to carry out useful biomedical tasks in vivo, is to endow them with the ability to detect and respond to molecules of interest. Target molecules may be disease indicators or cell surface receptors, and the responses may include conformational changes leading to release of therapeutically relevant cargo. Nucleic acid aptamers are ideally suited to this task and are beginning to be used in DNA origami designs. In this review we consider examples of uses of DNA aptamers in DNA origami structures and summarise what is currently understood regarding aptamer-origami integration. We review three major roles for aptamers in such applications: protein immobilisation, triggering of structural transformation, and cell targeting. Finally, we consider future perspectives for DNA aptamer integration with DNA origami.

Petrochemical plants use on-stream inspection more often to detect and monitor the corrosion on the equipment and piping system. Compared to ultrasonic thickness gauging and pulse-echo A-scan, phased array corrosion mapping has better coverability and can scan a large area to detect general and localized corrosion. This paper's objective is to obtain documentary evidence on the accuracy of corrosion detection from 30°C to 250°C on A36 low-carbon steel by carrying out simulation experiments every 10°C steps. A minimum of three sets of phased array corrosion mapping data in each temperature were collected to study and evaluate the detectability. The data evidence could enhance the confidence level of the plant's end users to use the phased array mapping in the future during an inspection. The experiments were found to be insufficiently thorough despite addressing the initial concerns, leaving more area for discussion in further studies, such as expanding the investigation to thicker carbon steel, stainless steel, and wedge materials.

Loss of photoreceptors in retinal degenerative diseases also impacts the inner retina: bipolar cell dendrites retract, neurons rewire and protein expression changes. ON-bipolar cells represent an attractive target for optogenetic vision restoration. However, above-described maladaptations may negatively impact the quality of restored vision. To investigate this question, we employed human post-mortem retinas and transgenic rd1_Opto-mGluR6 mice expressing the optogenetic construct Opto-mGluR6 in ON-bipolar cells and carrying the retinal degeneration rd1 mutation. We found significant changes in delayed rectifier potassium channel expression in ON-bipolar cells of degenerative retinas. In particular, we found an increase in Kv1.3 expression already in early stages of degeneration. Immunohistochemistry localized Kv1.3 channels specifically to OBC axons. In whole-cell patch-clamp experiments, ON-bipolar cells in the degenerated murine retina were less responsive, which could be reversed by application of the specific Kv1.3 antagonist Psora-4. Notably, Kv1.3 block significantly increased the amplitude and kinetics of Opto-mGluR6-mediated light responses in ON-bipolar cells of the blind retina and increased the signal-to-noise ratio of light-triggered responses in retinal ganglion cells. We propose that reduction of Kv1.3 activity in the degenerated retina, either by pharmacological block or by KCNA3 gene silencing, could improve the quality of restored vision.

Recently, there has been, on the one hand, an increase in the complexity of digital device designs and, on the other hand, an increase in the requirements for the development time and the reliability of the designs. One of the directions of solving this problem is developing new techniques for designing digital devices.This paper proposes a new technique for designing digital devices based on finite state machines with datapath (FSMD), when the functioning of the device is described in the form of an algorithm state machine with datapath (ASMD) charts. The new technique is called ASMD-FSMD. Different digital device design techniques are compared to each other using design examples of a synchronous multiplier on field programmable gate array (FPGA). The efficiency of the ASMD-FSMD technique compared to the traditional approach in terms of area and performance was investigated. The ASMD-FSMD technique, compared to the traditional one, reduces the area from 28.6% to 39.7% and increases the speed for some designs to 17.6%. In addition, using the ASMD-FSMD technique significantly reduces design time and increases design reliability. In conclusion, recommendations for using the ASMD-FSMD technique are made.

Current prenatal genetic evaluation showed a significantly increase in non-invasive screening and the reduction of invasive diagnostic procedures. To evaluate the diagnostic efficacy on detecting common aneuploidies, structural chromosomal rearrangements and pathogenic copy number variants (pCNV), we performed a retrospective analysis on a case series initially analyzed by aneuvysion fluorescence in situ hybridization (FISH) and karyotyping then followed by array comparative genomic hybridization (aCGH). Of the 386 cases retrieved from the past decade, common aneuploidies were detected in 137 cases (35.5%), other chromosomal structural rearrangements were detected in four cases (1%), and pCNV were detected in five cases (1.3%). The relative frequencies for common aneuploidies suggested a under detection of sex chromosome aneuploidies. Approximately 9.5% of cases with common aneuploidies showed a mosaic pattern. Inconsistent results between FISH and karyotyping were noted in cases with pseudo-mosaicism introduced by culture artifact or variable cellular proliferation from cells with mosaic karyotypic complements under in vitro cell culture. Based on findings from this case series, cell-based FISH and karyotyping should be performed to detect common aneuploidies, structural chromosomal abnormalities, and mosaic pattern. DNA-based aCGH and reflex FISH should be performed to detect and confirm genomic imbalances and pCNV. Practice points to ensure the diagnostic accuracy and efficacy were summarized.

Functional Near Infrared Spectroscopy (fNIRS) systems for e-health applications usually suffer of poor signal detection mainly due to a low end-to-end signal to noise ratio of the electronics chain. Lock-In Amplifiers (LIA) historically represent a powerful technique helping to improve performances in such circumstances. In this work it has been designed and implemented a digital LIA system, based on a Zynq® Field Programmable Gate Array (FPGA), trying to explore if this technique might improve fNIRS system performances. More broadly, FPGA based solution flexibility has been investigated, with particular emphasis applied to digital filter parameters, needed in the digital LIA, and it has been evaluated its impact on the final signal detection and noise rejection capability. The realized architecture was a mixed solution between VHDL hardware modules and software ones, running within a softcore microprocessor. Experimental results have shown the goodness of the proposed solutions and comparative details among different implementation will be detailed. Finally a key aspect taken into account throughout the design was its modularity, allowing an ease increase of the input channels while avoiding the growth of the design cost of the electronics system.

This study addresses the pressing energy constraints in nations like Bangladesh by proposing the implementation of photovoltaic (PV) microgrids. Given concerns about environmental degrada-tion, limited fossil fuel reserves, and volatile product costs, renewable energy sources are gaining momentum globally. Our research focuses on a grid-connected solar PV system model at Char Jazira, Lalpur, Natore, Rajshahi, Bangladesh. Through PVsyst simulation software, we assess the performance ratio (PR) and system losses, revealing an annual solar energy potential of 3375 MWh at Standard Test Condition (STC) efficiency. After considering losses, the system generates 2815 MWh annually, with 2774 MWh exported to the grid. We analyze an average PR of 78.63% and calculate a levelized cost of energy (LCOE) of 2.82 BDT/kWh [1 USD = 110 BDT]. The financial assessment indicates a cost-effective LCOE for the grid-connected PV system, with an annual gross income of 27744 BDT from selling energy to the grid and operating costs of 64060.60 BDT/year. Remarkably, this initiative can prevent 33074.061 tCO2 emissions over the project’s 25-year lifespan.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.