The effect of the angular rolling process on the plan view pattern of the plate is studied, the rectangular influence factor and improvement method for plate angular rolling process are proposed in this paper. Finite element models are established for the conventional rolling and angular rolling processes respectively, and with DEFORM software, the numerical simulation is carried out. A characterization formula reflecting the rectangular degree of the rolled piece is constructed and the rectangular degree of the plates under different rolling process conditions are compared. Considering the actual rolling process conditions, the range of theoretically calculated rectangular rotation angles is extended to obtain the optimum rectangular rotation angle with finite element simulation method. The one-group two-pass angular rolling is separated to one-group four-pass rolling and the simulation results show that the rectangular degree of the four-pass process is better than the two-pass process. Angular rolling experiments are carried out, the actual data shows that the rectangular characteristic value of the rolled piece is 1.003 with the four-pass process, and 1.014 with the two-pass process. It verifies that with separating one-group two-pass angular rolling process to one-group four-pass angular rolling process can improve the rectangular degree of the rolled plate.

In view of the floating rectangular aerostatic guideway problem of low load capacity and stiffness, this paper puts forward a kind of closed rectangular aerostatic guideway and its optimized design. Firstly, the analytic calculation formula of a closed rectangular aerostatic guideway was deduced. The use of MATLAB software for the numerical simulation and the parameter influence analyses was carried out in terms of the gas supply pressure on load capacity and stiffness. A simulation model of the rectangular air bearing was also built using the Fluent software, and the model was used for simulation calculations. Secondly, the static performance of the rectangular air bearing was analyzed by analyzing the distribution position and number of orifices on its load capacity and stiffness. On this basis, the response surface optimization design method is used to analyze the variation law of the load capacity and stiffness of the air bearing under different restrictor structural parameters. Finally, the optimal design parameters for the rectangular air bearing are obtained. The simulation results show that the optimized rectangular air bearing designed in this paper has a good load capacity and stiffness of 644.58N and 63.405N N∙μm^(-1).

One of the most important subjects of hydraulic engineering is the reliable estimation of the transverse distribution in rectangular channel of bed and wall shear stresses. This study makes use of the Tsallis entropy, Genetic Programming (GP) and (ANFIS) methods to assess the shear stress distribution (SSD) in rectangular channel. To evaluate the results of the Tsallis entropy, GP and ANFIS models, laboratory observations were used in which shear stress was measured using an optimized Preston tube. This is then used to measure the SSD in various aspect ratios in the rectangular channel. To investigate the shear stress percentage, 10 data series with a total of 112 different data for were used. The results of the sensitivity analysis show that the most influential parameter for the SSD in smooth rectangular channel is the dimensionless parameter B/H, Where the transverse co-ordinate is B, and the flow depth is H. With the parameters (b/B), (B/H) for the bed and (z/H), (B/H) for the wall as inputs, the modeling of the GP was better than the other one. Based on the analysis, it can be concluded that the use of GP and ANFIS algorithms is more effective in estimating shear stress in smooth rectangular channels than the Tsallis entropy-based equations.

Light absorption in single nanowires (NWs) is one of the most crucial factors for photovoltaic applications. In this paper, we carried out a detailed investigation of light absorption in single rectangular NWs (RNWs). We show that the RNWs exhibit improved light absorption compared with the square NWs (SNWs), which can be attributed to the symmetry-breaking structure that can increase the light path length by increasing the vertical side and the enhanced leaky mode resonances (LMRs) by decreasing the horizontal side. We found that the light absorption in silicon RNWs can be enhanced by engineering the horizontal and vertical sides, the photocurrent is significantly increased by 276.5% or 82.9% compared with that of the SNWs with the same side length as the horizontal side of 100 nm or the vertical side of 1000 nm, respectively. This work provides an effective way for designing high-efficiency single NW photovoltaic devices based on the symmetry breaking from the SNWs to RNWs.

Two-dimensional periodic Stokes flow of viscous incompressible fluid in a rectangular cavity with constant velocities applied to the top and bottom walls is considered. The study of chaotic advection regimes is reduced to the sequential solving of two problems. To solve the first problem, the analytical method of superposition, that allows to obtain any desired accuracy of the velocity field, is used. To solve the second problem, which is associated with obtaining the trajectories of individual fluid particles, numerical calculations of the Cauchy problem were performed. An analysis of the boundary conditions accuracy was performed based on the control of local integration. The advection of the selected volume of fluid in the rectangular cavity under the periodic motion of walls for a finite period time based on piecewise spline cubic interpolation is modelled. The obtained numerical results agree with well-known experimental data.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

The paper reports an analytical study of two problems of Rayleigh-Bénard convection(RBC): one in a Newtonian liquid occupying an axi-symmetric cylindrical enclosure(CE) and second in a two-dimensional rectangular enclosure(RE). Linear stability analysis is employed to obtain information on the onset of convection in terms of a critical Rayleigh number, Ra, as a function of the aspect ratio, Ro. The nature and the flow structures of the convective cells, at the onset of convection, are predicted theoretically by plotting the streamlines for different values of Ro. Not so shallow(Ro<1 or Ro≪1), and very shallow enclosures(Ro≫1) are considered. Concepts of cell-width and the wave number are respectively used in these two types of enclosures. An explicit analytical expression for the number of cells as a function of Ro is obtained theoretically. Exact prediction of the critical value of Ra, viz., Rac, as a function of Ro is also made. These are new findings in the case of both CE and RE. The fundamental differences between the problems of CE and RE are also highlighted.

We explore the use of inverse multiquadratic (IMQ) functions as basis functions when solving the vibrational Schrödinger equation with the rectangular collocation method. The quality of the vibrational spectrum of formaldehyde (in six dimensions) is compared to that obtained using Gaussian basis functions when using different numbers of width-optimized IMQ functions. The effects of the ratio of the number of collocation points to the number of basis functions and of the choice of the IMQ exponent are studied. We show that the IMQ basis can be used with parameters where the IMQ function is not integrable. We find that the quality of the spectrum with IMQ basis functions is somewhat lower that that with a Gaussian basis when the basis size is large and for a range of IMQ exponents. The IMQ functions are, however, advantageous when a small number of functions is used or with a small number of collocation points e.g. when using square collocation.

Due to the numerous heat sources in electronic equipment, the periodic nature of stream-wise flow occurs in a cooling channel so often, necessitating the development of an effective technique to improve the heat-cooling convection in such a situation. This paper investigates thermal convection enhancement in a heated-block duct through the periodic boundary conditions using the element-by-element (EBE) treatment in a semi-implicit projection finite element method (FEM) through preconditioned conjugate gradient (PCG) solver. This paper used the time-mean Nusselt number ratio, friction factor, and thermal performance to study how installing rectangular cylinders in the channel works with periodic boundary conditions varying Reynolds numbers (100, 175, and 250). The outcomes show that the rectangular cylinders installed stream-wise above an upstream block promote thermal convection in the heated-block duct. However, increasing the number of rectangular cylinders can raise friction factor. As a result, the case for periodic boundary conditions with a rectangular cylinder above every two blocks has the best thermal performance.

Optimizing the magnetic coupling of two coils of a dynamic wireless charging power supply for electric vehicles (EVs) is a challenging and crucial task. This article examines three situations of the magnetic coupling between two identical rectangular spiral coils with the same number of turns as a function of both the horizontal (X axis) and vertical (Z axis) alignment. In the first one, the analysis of the magnetic coupling between two copper air coils is presented. However, the obtained coupling coefficient was very low with a high leakage flux which affected the performance of the charging system. In the second case, a straightforward shielding method that involves inserting a magnetic material of the ferrite type is proposed to circumvent the aforementioned problems. Unfortunately, the obtained results show that simple shielding is still only a partial and insufficient solution. In the third situation, an aluminum sheet was consequently placed on the top of the ferrite to provide an adequate shielding structure. Additionally, a 3D analysis of the proper and mutual induction parameters separating the two coils as well as a magnetic field or induction distribution is also performed using the ANSYS Maxwell software. The results highlight the significance of the enhanced structure.

This paper presents an approach to the analysis of beams with rectangular cross-sections subjected to Saint-Venant torsion using the Fourier analysis, body forces being not considered. The Saint-Venant torsion of beams, also called free torsion or unrestrained torsion, is characterized by the absence of axial stresses due to torsion; only shear stresses are developed. The solution to this torsion problem consists of finding the Prandtl stress function that satisfies the governing equation and the boundary conditions, the governing equation being such that the Laplacian of the stress function has a constant value within the cross-section. In this paper, Fourier sine series was utilized to describe the constant value of the above mentioned Laplacian, while double sine series or simple sine series was utilized to describe the Prandtl stress function. Closed-form solutions in form of infinite series were derived for shear stresses, torsional constant and warping function. Those solutions were identical to the exact solutions.

Emphasizing the importance of acoustic attenuation in maintaining compliance with stringent noise regulations and enhancing workplace safety, the analysis covers the theoretical and practical aspects of sound attenuation in a turboengine testing stand. This paper presents a preliminary analysis and also an evaluation of a procedure for projecting a noise attenuator for industrial application and especially for turboengine test stands. While primarily focusing on the static acoustic behavior of the attenuator, considerations were also made regarding flow dynamics, Mach number-dependent attenuation, pressure drop, and self-generated noise aspects to provide a comprehensive perspective in selecting the optimal design configuration. The study investigates different calculation methods for assessment of the noise reduction for linear and staggered baffles, applied on a scaled reduced model of attenuator. Thus, the critical parameters and projecting requirements necessary for effective noise reduction in high-performance turboengine testing environments will be evaluated in a down-scaled model. Key factors examined include the selection of design parameters and configurations from various options. Advanced computational methods, like analytic and finite element analysis (FEM) are utilized to predict the acoustic performance and identify potential design optimizations. Experimental validation is performed to corroborate the simulation results, ensuring the reliability and efficiency of the attenuator. The findings indicate that a well-designed sound attenuator module can significantly reduce noise levels without compromising the operational performance of the turboengine inside a test cell.

Most IoT systems meant for implementing mission-critical systems are multi-layered based. The majority of the computing is done in the services and gateway layer. The Gateway layer connects the Internal section of the IoT to the cloud through the Internet. The failure of any node between the services servers and the gateways will isolate the entire network leading to zero tolerance. A networking topology is required to connect the service servers to the gateways, yielding 100% fault tolerance. Empirical formulation of the model chosen to connect the service’s servers to gateways through routers is required to compute the fault tolerance of the network. Rectangular and Interstitial Mesh have been proposed in this paper to connect the service servers to the gateways through the servers that yield 0.999 fault tolerance of the IoT network. An empirical formulation is also presented using which the Fault tolerance of the IoT network can be computed. An enhancement of 11% in the fault tolerance capability of an IoT network has been achieved by implementing Rectangular and Interstitial Mesh in the gateway layer of the network.

In this paper, thin plate theory and moderately thick plate theory are proposed for analyzing the bending problem of rectangular plates with stepped thickness resting on elastic half-space foundation. The ground reaction is considered as an unknown coefficient and the hypothesis of Winkler foundation model and two-parameter ground model is eliminated in this method, so as to obtain the law of internal force distribution of the plate and the distribution law of contact reaction force between the stepped rectangular plate and foundation. The stepped rectangular plate is divided into upper and lower plates, and thin plate theory and moderately thick plate theory are used to obtain the analytical solution. The obtained analytical solutions in this paper are compared with results reported in other publications to verify the accuracy of this method. The effects of the elastic modulus and dimensions of the plate, and theory of plate are also considered. The analytical solutions show that it is feasible to decompose the stepped rectangular plate into two plates for analyzing the bending properties of stepped rectangular plate, and this method provide a reference for the study of multilayer stepped rectangular plates.

This paper is a thorough review of innovative architectures of electro-hydraulic servovalves that exploit actuation systems based on piezo-electric materials. The use of commercially available piezo-electric actuators, namely, piezo-stacks, amplified piezo-stacks, rectangular benders and ring benders, is very promising for the actuation of the main stages and of the pilot stages of servovalves, given the fast response and low weight of piezoelectric materials. The use of these actuators can also allow novel designs to be developed, thus helping manufacturers to overcome the typical drawbacks of commercial servovalves, such as the high complexity and the high internal leakage of the pilot stages of two stage servovalves, as well as the large size and weight of direct drive servovalves. Firstly, the piezoelectric actuators that can be used for driving servovalves are presented in the paper and their characteristics are thoroughly discussed. Then, the main novel architectures present in the literature are explained and compared with the commercial ones, and their performance parameters are discussed to draw conclusions on the prospect that some of these architectures can be used by manufacturers as future designs.

In this paper, we introduce new formulas for calculating the restoring and repulsive magnetic forces between two non-coaxial circular loops with parallel axes. These formulas are derived from a modified version of Grover’s formula for mutual inductance between the coils in question. Utilizing these formulas, we compute the restoring and repulsive magnetic forces between two non-coaxial thick coils of rectangular cross-sections with parallel axes. In these calculations, we apply the filament method and conduct investigations to determine the optimal number of subdivisions for the coils in terms of computational time and accuracy. The method presented in this paper is also applicable to all conventional non-coaxial coils, such as disks, solenoids, and non-conventional coils like Bitter coils, all with parallel axes. This paper emphasizes the accuracy and computational efficiency of the calculations. Furthermore, the new method is validated according to several previously established methods

The object of this paper is the analysis of isotropic rectangular thin plates supported (simply supported or clamped) along two opposite edges whereby the other edges have arbitrary support conditions; the plates are subjected to external bending moments, concentrated or distributed, and perpendicular to the supported edges. The standard approach to this problem is to replace the bending moment with a couple of forces infinitely close and to use the known expressions of efforts and deformations for the plate subjected to concentrated forces; the results are then related to the first derivatives of those efforts and deformations with respect to the position of application of the load. In this study, the external bending moment was expanded into a Fourier series, leading to a distributed external bending moment, and the boundary conditions and continuity equations were applied. Various types of rectangular plates were analyzed, as well as plates of infinite length whose results were identical to those in the literature. In addition, results for cantilever plates of infinite length were presented.

This paper aims to analyze arbitrarily loaded isotropic rectangular thin plates with two opposite edges supported (simply supported or clamped), from which one or both are clamped, and the other edges have arbitrary support conditions. Rectangular thin plates with two opposite edges simply supported are routinely analyzed using for the deflection the simple trigonometric series of Lévy or the double trigonometric series of Navier, while the loads are expanded in Fourier series. In this paper the flexibility method (or force method) of the linear beam theory was applied whereby the unknowns were the bending moments along the opposite edges; in this regard, the primary system was the plate simply supported along the above-mentioned opposite edges and subjected to the external loads, system solved using the Lévy solution, and the redundant system was the plate simply supported along the opposite edges and subjected to bending moments along those edges. In the redundant system, a modified Lévy solution was introduced to account for the edge moments. The compatibility equations (vanishing of the slopes at selected positions of the opposite edges) were set to determine the unknowns and so the efforts in the plate. The results obtained were in good agreement with the exact results.

The object of this paper is the bending analysis of isotropic rectangular Kirchhoff plates subjected to non-uniform heating (NUH) using the Fourier transform method. The bottom and top surfaces of the plate are assumed to have different changes in temperature, whereas the change in temperature of the mid-surface is zero. According to classical plate theory, the governing equation of the plate contains second derivatives of the NUH; these derivatives are zero by constant value of the NUH, which leads to its absence in the governing equation. This paper presented an approach by which Fourier sine transform was utilized to describe the NUH, while the double trigonometric series of Navier and the simple trigonometric series of Lévy were utilized to describe the deflection curve. Thus, the NUH appeared in the governing equation, which simplified the analysis. Rectangular plates simply supported along all edges were analyzed, bending moments, twisting moments, and deflections being determined. In addition, rectangular plates simply supported along two opposite edges were analyzed; the other edges having various support conditions (free, simply supported, and fixed).

We quantitatively investigated the statistical behaviors of semiflexible polymer chains, which are simultaneously subjected to force stretching and rectangular tube confinement. Based on the wormlike chain model and Odijk deflection theory, we derived a new deflection length, by which new compact formulas are obtained for the confinement free energy and force-confinement-extension relation. These newly derived formulas have been justified by numerical solutions of an eigenvalue problem associated with the Fokker-Planck governing equation and extensive Brownian dynamics simulations based on the so-called Generalized Bead-Rod (GBR) model. We found that, comparing to the classical deflection theory, these new formulas are valid for a much extended range of the confinement-size /persistence-length ratio, and have no adjustable fitting parameters for sufficient long semiflexible chains in the whole deflection regime.

Heat enhancement is a topic of great interest nowadays due to its different application in industries. Porous material also known as metallic foam plays a major role in heat enhancement at the expenses of pressure drop. Flow in channels demonstrate the usefulness of this technology in heat extraction. In our current study, a porous strip attached to the channels walls is proposed as an alternative for heat enhancement. The thickness of the porous strip was varied for different Reynolds number. By maintaining laminar regime and using water as fluid, we determined an optimum thickness of porous material leading to the highest performance evaluation criterion. In our current study with the aspect ratio being the porous strip thickness over the channel width, an aspect ratio of 0.2 is found to be the alternative. A 40% increase in heat enhancement is detected in the presence of porous strip when compared to a clear channel case for a Reynolds number equal to 200 and improve further as the Reynolds number increase accordingly.

The aim of this paper is the analysis of arbitrarily loaded isotropic rectangular Kirchhoff plates supported at all corner points, whereby the edges are arbitrarily supported (simply supported, clamped, or free). Analytical methods commonly used include the single trigonometric series of Lévy, the double trigonometric series of Navier, the power series expansions, etc. In this paper the deflection surface was approximated with the sum of a particular solution to the governing differential equation (GDE) and two single series. The terms of the single series were the product of an unknown function of an independent variable and a trigonometric function of the other independent variable, whereby the trigonometric functions were chosen to vanish at the corner points. On the one hand the terms of the series were required to satisfy the homogeneous GDE, leading to two uncoupled differential equations, one for each unknown function, and so the approximate solution satisfied exactly the GDE. On the other hand the boundary conditions were satisfied only at selected collocation points along the boundary, the number of collocation points in each direction corresponding to the number of terms of the associated series. Results for several plates supported at all corner points with arbitrary edge support conditions were presented and showed good agreement with the exact results, the accuracy increasing the more terms of series were considered. Cantilevered plates and plates having two adjacent edges free will be analyzed using this approach in future research.

This work is a physical review, with elements of additions and thinning, on the methods of theoretical studies of nonlinear electrophysical phenomena in crystals with ion-molecular chemical bonds (CIMB). Crystals of this class include ionic dielectrics (characterized by high ionic conductivity), layered crystals, a special case of which are hydrogen-bonded crystals (HBC), defined as proton semiconductors and dielectrics (PSD).A scientific review (comparative analysis and justification of various approximations) was carried out on the methods of constructing and solving a generalized quasi-classical kinetic equation describing the mechanism of nonlinear relaxation polarization and conductivity processes in dielectric materials with ion-molecular chemical bonds (a special case is hydrogen-bonded crystals (HBC)) in a wide temperature range (1-1550 K) and polarizing field strengths (0.1-1000 V/m) at alternating field frequencies of the order of 1 kHz - 1000 MHz. The most important variant of the equations of the kinetic theory of dielectric relaxation in this work is the generalized non-linear by polarizing field quasi-classical kinetic equation of ionic (in HBC, proton) relaxation, based on the particle number balance equation (conductivity ions) in potential wells and having (in these models) the meaning of the ion current continuity equation (in HBC, protons), solved by the method of successive approximations by decomposition into infinite power series by degrees of a small dimensionless comparison parameter. It was found that in the area of ​ ​ weak fields (0.1-1 MW/m) at temperatures T = 50 - 550 K, for a number of ionic dielectrics (including HBC and similar dielectric properties and lattice structure) the generalized quasi-classical kinetic equation transforms to the linearized Fokker – Planck equation and, in the region of low (50-100K) and higher temperatures (250-550 K) begin to manifest non-linear polarization effects due to respectively proton tunneling (in the case of HBC) and volume charge relaxation (in the case of the HBC and for a wider class of ionic dielectrics). At ultra-low (1-10 K) temperatures in the region of weak fields (0.1-1 MW/m) and ultra-high temperatures (550-1550 K) in the region of strong fields (10-1000 MW/m), the contribution of this kind of effects to polarization is significantly enhanced. The effect of nonlinearities on relaxation times for microscopic acts of proton transitions across a potential barrier (assumed to be parabolic) is investigated. Nonlinear effects at volume-charge polarization in the hydrogen-bonded crystals (HBC) in alternating electric field, in radio frequency range are investigated. From the solution of the system of nonlinear Fokker-Planck equations (macroscopic kinetic equation) and Poisson, with blocking electrodes, using Fourier series, a recurrent (convenient for use in any approximation of perturbation theory) expression is constructed for complex amplitudes of relaxation modes of volumetric charge. Complex dielectric permittivity (CDP) is calculated as a series decomposition over even frequency harmonics of a variable field. The effect of quantum proton transitions and polarizing field parameters (strength, frequency) on the nonlinear properties of proton semiconductors and dielectrics has been established.