During the last 25 years the scientific community has coexisted with the most fascinating protocol due to Quantum Physics: quantum teleportation (QTele), which would have been impossible if quantum entanglement, so questioned by Einstein, did not exist. In this work, a complete architecture for the teleportation of Computational Basis States (CBS) is presented. Such CBS will represent each of the possible 24 classical bits commonly used to encode every pixel of a 3-color-channel-image (red-green-blue, or cyan-yellow-magenta). For this purpose, a couple of interfaces: classical-to-quantum (Cl2Qu) and quantum-to-classical (Qu2Cl) are presented with two versions of the teleportation protocol: standard and simplified.

In-situ nanoindentation experiment has been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiment in characterizing nonlinear material properties of 3D integrated microelectronic devices with through-silicon-vias (TSVs). The elastic, plastic, and interfacial fracture behavior of the copper via and matrix-via interface have been characterized using small scale specimens prepared with focused-ion-beam (FIB) and nanoindentation experiment. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7 to 83.7 degrees. The mixed-mode fracture strengths were extracted using the linear elastic fracture mechanics (LEFM) analysis and a fracture criterion was obtained by fitting the extracted data with the power-law function. The vectorial interfacial strength and toughness were found to be independent with mode-mix.

Wind tunnels are devices that enable researchers to study the flow over objects of interest, the forces acting on them and their interaction with the flow, which is nowadays playing an increasingly important role due to noise pollution. Since the first closed circuit wind tunnel with variable cross-section was built in G¨ottingen, its Prandtl configuration has little change. The wind tunnel with Prandtl configuration has four corners and vanes, more than 50% of the total pressure loss are caused by the corners and vanes. How to reduce the total pressure loss is a world class problem in the wind tunnel design. This study attempts to propose a novel configuration of wind tunnel, where the corners have been replaced by semi-circular tunnel. Sun wind tunnel 2 has only two corners and vanes, while Sun wind tunnel 1 has no corners and vanes at all. It is expected the new wind tunnel can reduce the total pressure loss from 50% to 10%.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

From a thermodynamic point of view, living cell life is no more than a cyclic process. It starts with the newly separated daughter cells and restarts when the next generations grow as free entities. In this cycle the cell changes its entropy. In cancer the growth control is damaged. In this paper we analyze the role of the volume-area ratio in cell in relation to the heat exchange between cell and its environment in order to point out the effect on the cancer growth. The result holds to a possible control of the cancer growth based on the heat exchanged by the cancer towards its environment, and the membrane potential variation, with the consequence of controlling the ions fluxes and the related biochemical reactions. This second law approach could represent a starting point for a possible future support for the anticancer therapies, in order to improve their effectiveness for the untreatable cancers.

Objective: The purpose of this study is to compare the effects of stretching methods for flexibility, muscle activation, and pressure pain threshold in ballet dancers, and to suggest an effective stretching method. Methods: Thirty-three ballet dancers were randomized to a static stretching group (n=11), muscle energy technique stretching group (n=11), and vibration-assisted stretching group (n=11). The angle of hip joint extension in arabesque, the activation of rectus femoris in Devéloppé, and the pressure pain threshold on rectus femoris in sitting position were measured to compare the effects of different stretching methods. Results: Hip joint extension angles increased in all stretching methods (p<0.05), however, vibration-assisted stretching and muscle energy technique stretching were more effective than static stretching (p<0.05). The activation of the rectus femoris decreased in all groups (p<0.05), but the muscle energy technique stretching group and the vibration-assisted stretching group showed a significant decrease compared to the static stretching group (p<0.05). The pressure pain threshold showed significant improvement only in the static stretching group (p<0.05), and the vibration-assisted stretching group (p<0.05). Conclusion: Vibration-assisted stretching compared to static stretching and muscle energy technique stretching is a beneficial method for flexibility, muscle activation, and pressure pain threshold in ballet dancers.

The study sought to determine solar irradiation in Homa Bay County which can be tapped and utilized in improving lives of residents of the region by converting the solar thermal energy in Home Bay to other forms of energy such as electric form, mechanical form and light. The study was done by assessing the local atmospheric conditions which included sunshine duration data and air temperature records for the period of two years and the data obtained subjected to statistical analysis to determine the localized characteristics of the resource. The characteristics that were examined include; seasonal and annual power expectations as well as resource reliability. The solar irradiance of Home County was found to be 768.0 W/m².

The development of new target stations for radioisotope production based on a dedicated 70~MeV commercial cyclotron is described. Currently known as the South African Isotope Facility (SAIF), this initiative will free the existing separated-sector cyclotron (SSC) at iThemba LABS (near Cape Town) to mainly pursue research activities in nuclear physics and radiobiology. It is foreseen that the completed SAIF facility will realize a three-fold increase in radioisotope production capacity compared to the current programme based on the SSC.

In this paper, the far field and near field optical responses of a gold nanoparticle are studied and simulated numerically. The electromagnetic field was excited by an electric dipole located near one end of the nanorod, which is used to model the emission of a quantum dot. Another excitation method was also simulated in which an incident plane wave is used. The excitation of dark plasmon modes of the gold nanorod is presented. The Poynting equation was solved numerically to study the influence of the gold nanorod on the dipole radiative power. In addition, the extinction cross section of the gold nanoparticle illuminated by the incident plane wave was calculated to estimate the amount of the scattered and absorbed light.

This letter attempts to find splashing height of liquid-filled container drop impact to a solid surface by dimensional analysis (DA). Two solutions were obtained by both traditional DA and directed DA without solving any governing equations. It is found that the directed DA can provide much more useful information than the traditional one. This study shows that the central controlling parameter is called splash number $\mathrm{Sp}=\mathrm{Ga} \mathrm{La}^\beta=(\frac{gR^3}{\nu^2})(\frac{\sigma R}{\rho \nu^2})^\beta$, which is the collective performance of each quantity. The splash height is given by $ \frac{h}{H}=(\frac{\rho\nu^2}{\sigma R})^\alpha f[\frac{gR^3}{\nu^2}(\frac{R\sigma}{\rho\nu^2})^\beta]=\frac{1}{\mathrm{La}^\alpha}f(\mathrm{Ga}\cdot \mathrm{La}^\beta)$. From the physics of the splashing number, we can have a fair good picture on the physics of the liquid splashing as follows: the jets propagation will generate vortex streets from the container bottom due to sudden pressure increasing from drop impact (water-hammer effect), which will travel along the container sidewall to the centre of the container and subsequently excite a gravity wave on the liquid surface. The interaction between the gravitational force, surface force and viscous force is responsible for creating droplet splash at the liquid surface.

In this paper, we examine the mathematical and physical consistencies of the three primary couple stress theories: original Mindlin-Tiersten-Koiter couple stress theory (MTK-CST), modified couple stress theory (M-CST) and consistent couple stress theory (C-CST). As has been known for many years, MTK-CST suffers from some fundamental inconsistencies, such as the indeterminacy of the couple-stress tensor. Therefore, despite the fact that MTK-CST has a fundamental position in the evolution of size-dependent continuum mechanics, it is not a reliable theory within continuum mechanics, for example, in developing new size-dependent multi-physics formulations. We also observe that M-CST not only inherits all inconsistences from the original MTK-CST, but also suffers from new additional inconsistencies, such as the introduction of a new non-physical governing equation. These inconsistencies refute the claim of those who state that the couple-stress tensor may be chosen symmetric. Therefore, the apparent success of MTK-CST and M-CST in describing a size-effect for some problems, such as two-dimensional plate and beam bending, is not enough to justify these theories as suitable for general cases. In fact, the symmetric couple-stresses in M-CST create torsional or anticlastic deformation, not bending. On the other hand, C-CST, with a skew-symmetric couple-stress tensor, is the consistent continuum mechanics suitable for solving different size-dependent solid, fluid and multi-physics problems.

Complex human behavior, including interlimb and interpersonal coordination, has been studied from a dynamical system perspective. We review the applications of a dynamical system approach to a sporting activity, which includes continuous, discrete, and switching dynamics. Continuous dynamics identified switching between in- and anti-phase synchronization, controlled by an interpersonal distance of 0.1 m during expert kendo matches, using a relative phase analysis. As discrete dynamics, return map analysis was applied to the time series of movements during kendo matches, and six coordination patterns were classified. Furthermore, state transition probabilities were calculated based on the two states, which clarified the coordination patterns and switching behavior. We introduced switching dynamics with temporal inputs to clarify the simple rules underlying the complex behavior corresponding to switching inputs in a striking action as a non-autonomous system. As a result, we determined that the time evolution of the striking action was characterized as fractal-like movement patterns generated by a simple Cantor set rule with rotation. Finally, we propose a switching hybrid dynamics to understand both court-net sports, as strongly coupled interpersonal competition, and weakly coupled sports, such as martial arts.

An increase of seismic activity is often observed before large earthquakes. Events responsible for this increase are usually named foreshock and their occurrence probably represents the most reliable precursory pattern. Many foreshocks statistical features can be interpreted in terms of the standard mainshock-to-aftershock triggering process and are recovered in the Epidemic Type Aftershock Sequence ETAS model. Here we present a statistical study of instrumental seismic catalogs from four different geographic regions. We focus on some common features of foreshocks in the four catalogs which cannot be reproduced by the ETAS model. In particular we find in instrumental catalogs a significantly larger number of foreshocks than the one predicted by the ETAS model. We show that this foreshock excess cannot be attributed to catalog incompleteness. We therefore propose a generalized formulation of the ETAS model, the ETAFS model, which explicitly includes foreshock occurrence. Statistical features of aftershocks and foreshocks in the ETAFS model are in very good agreement with instrumental results.

3D meso-scale structures that can reach up to centimeters in overall size but retain micro- or nano-features, proved to be promising in various science fields ranging from micro-mechanical metamaterials to photonics and bio-medical scaffolds. In this work we present synchronization of the linear and galvano scanners for efficient femtosecond 3D optical printing of objects at the meso-scale (from sub-μm to sub-cm spanning five orders of magnitude). In such configuration the linear stages provide stitch-free structuring at nearly limitless (up to tens-of-cm) working area, while galvo-scanners allow to achieve translation velocities in the range of mm/s-cm/s without sacrificing nano-scale positioning accuracy and preserving undistorted shape of the final print. The principle behind this approach is demonstrated, proving its inherent advantages in comparison to separate use of only linear stages or scanners. The printing rate is calculated in terms voxels/s, showcasing the capability to maintain an optimal feature size while increasing throughput. Full capabilities of this approach are demonstrated by fabricating structures that reach millimeters in size but still retain μm-scale features: scaffolds for cell growth, microlenses and photonic crystals. All this is combined into a benchmark structure: a meso-butterfly. Provided results show that synchronization of two scan modes is crucial for the end goal of industrial-scale implementation of this technology and makes the laser printing well aligned with similar approaches in nanofabrication by electron and ion beams.

We study the effect of polymer coating, pressure, temperature and light on the electrical characteristics of monolayer WSe₂ back-gated transistors with quasi-ohmic Ni/Au contacts. We prove that the removal of a layer of poly(methyl methacrylate) or a decrease of the pressure change the device conductivity from p to n-type. We demonstrate a gate-tunable Schottky barrier at the contacts and measure a barrier height of ~70 meV in flat-band condition. We report and discuss a temperature-driven change in the mobility and the subthreshold slope which we use to estimate the trap density at the WSe₂/SiO₂ interface. We study the spectral photoresponse of the device, that can be used as a photodetector with a responsivity of ~0.5 AW^-1 at 700 nm wavelength and 0.37 mW/cm² optical power.

This paper presents the design, fabrication and characterization of Schottky erbium/silicon photodetectors working at 1.55 µm. These erbium/silicon junctions are carefully characterized using both electric and optical measurements at room temperature. A Schottky barrier ΦB of ~673 meV is extrapolated; the photodetectors show external responsivity of 0.55 mA/W at room temperature under a 8 V of reverse bias applied. In addition, the device performance is discussed in terms of normalized noise and noise equivalent power. To the best of our knowledge, these are the first Er/Si photodetectors designed for operation in free space at 1.55 µm. The proposed devices will pave the way towards development of Er-based photodetectors and light sources to be monolithically integrated in the same silicon substrate and both operating at 1.55 µm.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

Optofluidics, a research discipline combining optics with microfluidics, currently aspires to revolutionize the analysis of biological and chemical samples e.g. for medicine, pharmacology, or molecular biology. In order to detect low concentrations of analytes in water, we developed an optofluidic device containing a nanostructured substrate for surface enhanced Raman spectroscopy (SERS). The geometry of the gold surface allows localized plasmon oscillations to give rise to the SERS effect, in which the Raman spectral lines are intensified by the interaction of the plasmonic field with the electrons in the molecular bonds. The SERS substrate was enclosed in a microfluidic system, which allowed transport and precise mixing of the analyzed fluids, while preventing contamination or abrasion of the highly sensitive substrate. To illustrate its practical use, we employed the device for quantitative detection of persistent environmental pollutant 1,2,3-trichloropropane in water in submillimolar concentrations. The developed sensor allows fast and simple quantification of halogenated compounds and it will contribute towards the environmental monitoring and enzymology experiments with engineered haloalkane dehalogenase enzymes.

Imaging living cells by atomic force microscopy (AFM) promises not only high-resolution topographical data, but additionally, mechanical contrast, which are not obtainable with other microscopy techniques. Such imaging is however challenging, as cells need to be measured with low interaction forces to prevent either deformation or detachment from the surface. Off-resonance modes which periodically probe the surface have been shown to be advantageous, as they provide excellent force control combined with large amplitudes, which help reduce lateral force interactions. However, the low actuation frequency in traditional off-resonance techniques limits the imaging speed significantly. Using photothermal actuation, we probe the surface by directly actuating the cantilever. Due to the much smaller mass that needs to be actuated, the achievable measurement frequency is increased by two orders of magnitude. Additionally, photothermal off-resonance tapping retains the precise force control of conventional off-resonance modes and is therefore well suited to gentle imaging. Here we show how photothermal off-resonance tapping can be used to study live cells by AFM. As an example of imaging mammalian cells, the initial attachment, as well as long term detachment of a human thrombocytes are presented. The membrane disrupting effect of the antimicrobial peptide CM-15 is shown on the cell wall of E. coli. Finally, the dissolution of the cell wall of B. subtilis by lysozyme is shown. Taken together, these evolutionarily disparate forms of life exemplify the usefulness of PORT for live cell imaging in a multitude of biological disciplines.

In order to alter and adjust the shape of the membrane, cells harness various mechanisms of curvature generation. Many of these curvature generation mechanisms rely on the interactions between peripheral membrane proteins, integral membrane proteins, and lipids in the bilayer membrane. One of the challenges in modeling these processes is identifying the suitable constitutive relationships that describe the membrane free energy that includes protein distribution and curvature generation capability. Here, we review some of the commonly used continuum elastic membrane models that have been developed for this purpose and discuss their applications. Finally, we address some fundamental challenges that future theoretical methods need to overcome in order to push the boundaries of current model applications.

Long-term durability of the vacuum edge-seal plays a significant part in retrofitting triple vacuum glazing (TVG) to existing buildings in achieving towards zero-energy buildings (ZEB) target. Vacuum pressure decrement with respect to time between panes affect the thermal efficiency of TVG. This study reports a 3D finite element model, with validated mathematical methods and comparison, for the assessment of the influence of vacuum pressure diminution on the thermal transmittance (U value) of TVG. The centre-of-pane and total U values of TVG calculated to be 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ at the cavity vacuum pressure of 0.001 Pa. The results suggests that a rise in cavity pressure from 0.001 Pa to 100 kPa increases the centre-of-pane and total U values from 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ to 2.4 Wm⁻²K⁻¹ and 2.58 Wm⁻²K⁻¹, respectively. The temperature descent on the surfaces of TVG between hot and cold sides’ increases by decreasing the cavity vacuum pressure from 50 kPa to 0.001 Pa. To maintain the cavity vacuum pressure of 0.001 Pa for over 20 years of life span in the cavity of 10 mm wide edge sealed triple vacuum glazing, non-evaporable getters will maintain the cavity vacuum pressure that will enable the long-term durability to TVG.

Quality control (QC) may be a lengthy and tedious process. As a result, most data users use data from meteorological services without performing data quality checks. The South African Weather Service (SAWS) re-established the national solar radiometric network comprising of 13 new stations within the six climatic zones of the country. This study reports on the performance results of the Baseline Surface Radiation Network (BSRN) QC procedures applied to the solar radiation data within the SAWS radiometric network. The overall percentage performance of the SAWS solar radiation network based on BSRN QC methodology is 97.79%, 93.64%, 91.6% and 92.23% for Long Wave Downward Irradiance (LWD), Global Horizontal Irradiance (GHI), Diffuse Horizontal Irradiance (DHI) and Direct Normal Irradiance (DNI) respectively with operational problems largely dominating the percentage of bad data. The overall average performance of the Surface Solar Radiation Dataset – Heliosat (SARAH) data records for the GHI estimation for all the stations showed a Mean Bias Deviation (MBD) of -8.28 Wm^-2, a Mean Absolute Deviation (MAD) of 9.06 Wm^-2 and the Root Mean Square Deviation (RMSD) of 11.02 Wm^-2. The correlation (quantified by R²) between ground-based and SARAH-derived GHI time series was ~ 0.98. The established network has the potential of providing high quality minute solar radiation data sets (GHI, DHI, DNI and LWD) and auxiliary hourly meteorological parameters vital for scientific and practical applications in renewable energy technologies in South Africa.

Background: This study aims to compare the impact of early and late post-discharge cardiopulmonary rehabilitation on the outcomes of intensive care unit (ICU) survivors. Methods: The retrospective, cohort study used a sub-database of the Taiwan National Health Insurance Research Database (NHIRD) that contains information of all patients had ICU admission between 2000 and 2012. Early group was defined if patients had received cardiopulmonary rehabilitation within 30 days after ICU discharge, and late group was define as if patients had received cardiopulmonary rehabilitation between 30 days and one year after ICU discharge. The end points were mortality and re-admission during the 3-year follow-up. Results: Among 2136 patients received cardiopulmonary rehabilitation after ICU discharge, 994 was classified early group and other 1142 patients were classified as late group. Overall, early group had a lower mortality rate (6.64% vs 10.86%, p = 0.0006), and a lower ICU readmission rate (47.8% vs 57.97%, p < 0.0001) than late group after 3-year follow-up. Kaplan-Meier analysis showed that early group had significantly lower mortality (p=0.0009) and readmission rate (p<0.0001) than late group. In multivariate analysis, the risk of ICU readmission was found to be independently associated with late group (HR, 1.28; 95% CI, 1.13-1.47). Conclusions: Early post-discharge cardiopulmonary rehabilitation among ICU survivors has the long-term survival benefit and significantly decreases the readmission rate.

Physics behind collimated highly directional nature of lasers, and factors that keep the seven coloured waves that form white light together during their journey from Sun to Earth, in the face of the natural disruptive forces, is not fully understood. Energy levels were measured, in terms of alterations in induced current and voltage, in beams from a red laser, white LED light and the Sunlight before and during their disruption by diffusers (frosted glass for the lasers) and diffractors (diffraction grating for the white light) using a photovoltaic solar cell panel attached to a digital multimeter. Results show that disruption of the beams results in release of extra energy named as ‘Latent Light Binding’ Energy’. It is hypothesized that the ‘binding’ energy keeps laser waves firmly bound together both end-on and side-on enabling laser beams to travel long distances in collimated manner. Likewise, the 7 coloured waves that constitute white light are kept together, probably side-on, in their journey from the Sun to the Earth. The observation that diffraction of sunbeam is associated with increased power generation provides a new lead to improve harnessing of solar energy, where, currently, the focus is mainly on improving efficiency of photovoltaic cell.

A simplified version of the quantum teleportation protocol is presented in here. Its experimental confirmation will have deep implications for a better understanding of Quantum Entanglement with a particular projection on Quantum Communications.

In this research, we developed a wearable temperature-sensing element by dip dyeing threads in poly (3, 4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) (p-type conducting polymer) solution. The PEDOT:PSS was used to dye the textile and it exhibited negative temperature coefficient characteristics in which the resistance decreases as the temperature increases. The fabricated temperature-detection thread achieved a sensitivity of 167.1 W/°C with 99.8% linearity in the temperature range of -50 to 80 °C. We anticipate that temperature sensors that apply our technology will be made as stitch- or textile-type for wearable devices, and they will be widely adopted for different applications such as in fitness, leisure, healthcare, medical treatment, infotainment, industry, and military applications, among others.

We report on the study of energy-harvesting performance in medium-size (400 cm²) glass-based semitransparent solar concentrators employing edge-mounted photovoltaic modules. Systems using several different types of glazing system architecture and containing embedded diffractive structures are prepared and characterized. The technological approaches to the rapid manufacture of large-area diffractive elements suitable for use in solar window-type concentrators are described. These elements enable the internal deflection and partial trapping of light inside glass-based concentrator windows. We focus on uncovering the potential of pattern-transfer polymer-based soft lithography for enabling both the improved photon collection probability at solar cell surfaces, and the up-scaling of semitransparent solar window dimensions. Results of photovoltaic characterization of several solar concentrators employing different internal glazing-system structure and diffractive elements produced using different technologies are reported and discussed.

The aim of this study is to investigate, by means of experimental measurements and full-wave simulations, the dominant factors for the very high-resolution (VHR) radar image speckles from exponential correlated rough surfaces. A Ka-band radar system was used to collect the return signal from such a surface sample fabricated by 3D printing, and that signal was further processed into images at different resolution scales, where the image samples were obtained by horizontally turning around the surface sample. To cross-validate the results and to further discuss the VHR speckle properties, full wave simulations by full 3D Finite Difference Time Domain (FDTD) method were conducted with 1600 realizations for the speckle analysis. At the considered very high resolution, speckle statistics show divergence from the fully developed Rayleigh distribution. The factors that impact on the high-resolution speckle properties from exponential correlated rough surface, are analyzed in views of the equivalent number of scatterers theory and scattering scales, respectively. From the data results and extended discussions, it is evident that both of the above factors matter for VHR speckle of backscattering, from the exponential correlated rough surface as a good representative for the ground surface.

This work reports measurements of calcified gallstone elemental compositions using laser-induced optical emission spectroscopy. The experimental results support the importance of the magnesium concentration in gallstone growth. Granular stones reveal an increased magnesium concentration at the periphery of the granules, suggesting the inhibition of further growth. Non-granular gallstones reveal lower overall magnesium concentrations but with higher values near the center.

We investigate on the plasmons of monolayer MoS₂ in the presence of spin-orbit interactions (SOIs) under the random phase approximation. The theoretical study shows that two new and novel plasmonic modes can be achieved via inter spin sub-band transitions around the Fermi level duo to the SOIs. The plasmon modes are optic-like, which are very different from the plasmon modes reported recently in monolayer MoS₂, and the other two-dimensional systems. The frequency of such plasmons increases with the increasing of the electron density or the spin polarizability, and decreases with the increasing of the wave vectors q. Our results exhibit some interesting features which can be utilized to the plasmonic and terahertz devices based on monolayer MoS₂.

The development of efficient luminescent systems, such as microcavities, solid state lasers, integrated optical amplifiers, optical sensors is the main topic in glass photonics. The building blocks of these systems are glass-ceramics activated by rare earth ions because they exhibit specific morphologic, structural and spectroscopic properties. Among various materials that could be used as nanocrystals to be imbedded in silica matrix, tin dioxide presents some interesting peculiarities, e.g. the presence of tin dioxide nanocrystals allows increase in both solubility and emission of rare earth ions. Here, we focus our attention on Er³⁺ - doped silica – tin dioxide photonic glass-ceramics fabricated by sol-gel route. Although the SiO₂-SnO₂:Er³⁺ could be fabricated in different geometrical systems: thin films, monoliths and planar waveguides we herein limit ourselves to the monoliths. The effective role of tin dioxide as luminescence sensitizer for Er³⁺ ions is confirmed by spectroscopic measurements and detailed fabrication protocols are discussed.

Optical tweezers offer a non-contact method for selecting single cells and translocating them from one microenvironment to another. We have characterized the optical tweezing of yeast S. cerevisiae and can manipulate single cells at velocities up to 0.77 mm/s using laser powers of 40 mW from a 785 nm diode laser. We have fabricated and tested three cell isolation devices; a micropipette, a PDMS chip and laser machined fused silica chip and we have isolated single bacteria, yeast and cyanobacteria cells. The most effective isolation was achieved in PDMS chip, where single yeast cells were grown and observed for 18 hours without contamination. The duration of budding in S. cerevisiae was not affected by the laser parameters used, but the time from tweezing until the first budding event began increased with increase laser energy (laser power x time). Cells tweezed using 25 mW for 1 minute were viable after isolation. We have constructed a micro-consortium of yeast cells, and a co-culture of yeast and bacteria, using optical tweezers in combination with the PDMS network of channels and isolation chambers, which may impact on both industrial biotechnology and understanding pathogen dynamics.

In this letter, it is proposed that cryogenic quantum bits could operate based on the nonlinearity due to the quantum capacitance of two-dimensional Dirac materials, and in particular graphene. The anharmonicity of a typical superconducting quantum bit is calculated and the sensitivity of quantum bit frequency and anharmonicty with respect to temperature are found. Reasonable estimates reveal that a careful fabrication process could reveal the expected properties, thus putting the context of quantum computing hardware into new perspectives.

A study of photovoltaic solar window technologies is reported, focusing on their structural features, functional materials, system development, and suitability for use in practical field applications, e.g. public infrastructures and agricultural installations. Energy generation performance characteristics are summarized and compared to theory-limit predictions. Working examples of pilot-trial solar window-based installations are described. We also report on achieving electric power outputs of about 25 W_p/m² from clear and transparent large-area glass-based solar windows.

Current smartphones incorporate different types of sensors that allow us to know our spatial position, they give us information about pressure, speed, acceleration, time, acoustic level, and other different physical magnitudes. These smartphones measure each component of the magnetic field, bearing in mind that any current perpendicular to a magnetic field produces a small potential difference, transversal to the said current, being this voltage easily measurable by Hall sensors. With the implementation of three Hall sensors, and an appropriate app, we can measure the three components of the magnetic field vector, and with this we can obtain information and deduce properties of the physical systems considered. In this paper we are exploring the use of smartphones in a physics laboratory for freshman students. To do this, we have measured, using Hall sensors, the magnetic field created by a linear quadrature, and we have obtained, first of all, its dependence on the distance between the quadrupole and the magnetic sensor. The second purpose of this work is to show that the laboratory is a powerful tool that increases the significant learning of freshman students through advanced technological tools.

Internal and mesoscopic variables differ from each other fundamentally: both are state space variables, but mesoscopic variables are additional equipped with a distribution function introducing a statistical item into consideration which is missing in connection with internal variables. Thus, the alignment tensor of liquid crystal theory can be introduced as an internal variable or as one generated by a mesoscopic background using the microscopic director as mesoscopic variable. Because the mesoscopic variable is part of the state space, the corresponding balance equations change into mesoscopic balances, and additionally an evolution equation of the mesoscopic distribution function appears. The flexibility of the mesoscopic concept is not only demonstrated for liquid crystals, but is also discussed for dipolar media and flexible fibers.

Li-ion cell designs, component integrity and manufacturing processes all have critical influence on the safety of Li-ion batteries. Any internal defective features that induce a short circuit, can trigger a thermal runaway: a cascade of reactions, leading to a device fire. As consumer device manufacturers push aggressively for increased battery energy, instances of field failure are increasingly reported. Notably Samsung made a press release in 2017 following a total product recall of their Galaxy Note 7 mobile phone, confirming speculation that the events were attributable to the battery and its mode of manufacture. Recent incidences of battery swelling on the new iPhone 8 have been reported in the media, and the techniques and lessons reported herein may have future relevance. Here we look deeper into the key components of one of these cells and confirm evidence of cracking of electrode material in tightly folded areas, combined with a delamination of surface coating on the separator, which itself is an unusually thin monolayer. We report microstructural information about the electrodes, battery welding attributes and thermal mapping of the battery whilst operational. The findings point to the most likely combination of events and highlights the impact of design features, whilst providing structural considerations most likely to have led to the reported incidences relating to this phone.

Resistive patch array incorporating with metallic backplane provided an effective way to the achievement of broadband metamaterial absorbers(MAs). When loading metallic metamaterial to resistive MA, the outstanding construction helps realize more flexible and diversified forms of broadband absorption. In this paper, we attempted to load metallic resonators(MRs) to resistive MA in the three-dimensional construction, which benefits further enhancement of lower-frequency absorption. Simulation showed that the partial absorption band was separated to lower frequency, while the rest of broadband absorption was unaffected. Meanwhile, after combining multi-unit of the proposed MAs, the stair-stepping broadband absorption was also achieved. At last, three samples were fabricated. The agreements between simulations and experimental results demonstrated that resistive MA loaded with MRs provided an effective way for further enhancement of lower-frequency absorption with almost no change of the absorbing structure and areal density. Thus, it is worthy to expect a wide range of applications to emerge inspired from the proposed attempt.

This paper deals with bistatic subsurface probing of a horizontally layered dielectric half-space by means of ultra-wideband electromagnetic pulses. A receiver collects reflections from the air-ground interface and from the gradients of dielectric permittivity in the half-space. This scenario is of interest for ground penetrating radar (GPR) applications. For the analytical description of the received signal, we developed and implemented a novel time-domain version of the coupled-wave Wentzel–Kramers–Brillouin approximation. Our solution is in very good agreement with finite-difference time-domain results, radically accelerates calculations, and effectively accounts for the protracted return signals observed in the lower part of the GPR spectrum. The paper includes results showing the application of the proposed technique to two case studies: in particular, the method was employed for the post-processing of experimental radargrams collected on Lake Chebarkul, in Russia, and to simulate GPR probing of the Moon surface, to detect smooth gradients of the dielectric permittivity in lunar regolith.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

Osteoarthritis (OA) is a common joint disorder found mostly in elderly people. The role of mechanical behavior in the progression of OA is complex and remains unclear. The stress-relaxation behavior of human articular cartilage in clinically defined osteoarthritic stages may have importance in diagnosis and prognosis of OA. In this study we investigated differences in the biomechanical responses among human cartilage of ICRS grades I, II and III using polymer dynamics theory. We collected 24 explants of human articular cartilage (eight each of ICRS grade I, II and III) and acquired stress-relaxation data applying a continuous load on the articular surface of each cartilage explant for 1180 s. We observed a significant decrease in Young’s modulus, stress-relaxation time, and stretching exponent in advanced stages of OA (ICRS grade III). The stretch exponential model indicated that significant loss in hyaluronic acid polymer might be the reason for the loss of proteoglycan in advanced OA. This work encourages further biomechanical modelling of osteoarthritic cartilage utilizing these data as input parameters to enhance the fidelity of computational models aimed at revealing how mechanical behaviors play a role in pathogenesis of OA.

Background: Modern MEG devices include 102 sensor triplets containing one magnetometer and two planar gradiometers. The first processing step is often a signal space separation (SSS), which provides a powerful noise reduction. A question commonly raised by researchers and reviewers is which data should be employed in source reconstruction: (1) magnetometers only, (2) gradiometers only, (3) magnetometers and gradiometers together. The MEG community is currently divided about the proper answer and strong arguments in favor and against these three approaches often expressed. Methods: First, we provide theoretical evidence that both gradiometers and magnetometers contain the same information after SSS, and argue that they both result from the backprojection of the same SSS components. Then, we compare beamforming source reconstructions from magnetometers and gradiometers in real MEG recordings before and after SSS. Results: Without SSS, the correlation between source time series extracted from magnetometers and gradiometers was high, with Pearson correlation coefficient r=0.5-0.8. After SSS, these correlation values increased dramatically, reaching over 0.90 across all cortical areas. Conclusions: After SSS, almost identical source reconstructions (r>0.9) can be obtained with magnetometers and gradiometers, as long as regularization is selected appropriately to account for the different properties in magnetometers and gradiometers covariance matrices.

We overview recent progress in growth aspects of group III-nitride heterostructures for deep ultraviolet (DUV) light-emitting diodes (LEDs), with particular emphasis on the growth approaches for attaining high-quality AlN and high Al-molar fraction AlGaN. The discussion commences with the introduction of the current status of group III-nitride DUV LEDs and the remaining challenges. This segues into discussion of LED designs enabling high device performance followed by the review of advances in the methods for the growth of bulk single crystal AlN intended as a native substrate together with a discussion of its UV transparency. It should be stated, however, that due to the high-cost of bulk AlN substrates at the time of this writing, the growth of DUV LEDs on foreign substrates such as sapphire still dominates the field. On the deposition front, the heteroepitaxial growth approaches incorporate high-temperature metal organic chemical vapor deposition (MOCVD) and pulsed-flow growth, a variant of MOCVD, with the overarching goal of enhancing adatom surface mobility, and thus epitaxial lateral overgrowth which culminates in minimization the effect of lattice- and thermal-mismatches. This is followed by addressing the benefits of pseudomorphic growth of strained high Al-molar fraction AlGaN on AlN. Finally, methods utilized to enhance both p- and n-type conductivity of high Al-molar fraction AlGaN are reviewed.

In this paper, a novel integrated high precision vacuum microelectronic accelerometer is put forward based on the theory of field emission, the accelerometer consists of sensitive structure and interface ASIC. The sensitive structure has a mass of a cathode cone tips array, a folded beam, an emitter electrode and a feedback electrode. The sensor is fabricated on a double side polished (1 0 0) N-type silicon wafer, the tips array of cathode are shaped by wet etching with HNA (HNO3, HF and CH3COOH) and metalized by TiW/Au thin film. The structure of sensor is released by ICP process finally. The interface ASIC was designed and fabricated based on the P-JFET high voltage bipolar process. The accelerometer is tested through static field rollover test, and the test results show the integrated vacuum microelectronic accelerometer has good performances, which sensitivity is 3.081V/g and non-linearity is 0.84% in the measuring range of −1g~1g.

A linear stability analysis of the parallel uniform flow in a horizontal channel with open upper boundary is carried out. The lower boundary is considered as an impermeable isothermal wall, while the open upper boundary is subject to a uniform heat flux and it is exposed to an external horizontal fluid stream driving the flow. An eigenvalue problem is obtained for the two-dimensional transverse modes of perturbation. The study of the analytical dispersion relation leads to the conditions for the onset of convective instability as well as to the determination of the parametric threshold for the transition to absolute instability. The results are generalised to the case of three-dimensional perturbations.

A highly-integrated experimental system for plasma decomposition of fuels was built. Experiments were conducted and confirmed that macromolecular chain hydrocarbons were cracked by large-gap dielectric barrier discharge under the excitation of a microsecond-pulse power supply. Alkanes and olefins with a C atom number smaller than 10 as well as hydrogen were found in the cracked products of n-decane (n-C10H22). The combination of preheating and plasma decomposition had strong selectivity for olefins. Under strong discharge conditions, micromolecular olefins were found in the products. Moreover, there was a general tendency that micromolecular olefins gradually accounted for higher percentage of products at higher temperature and discharge frequency.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

The modeling of flood-induced bend scour near embankment toes can provide important information for river engineering, embankment safety warnings, and emergency action management. During the rainy seasons, short-term general scour and bend scour are the most common causes for the failure of reinforced concrete embankments in Taiwan. To gain a deeper understanding of the scouring process near levee foundations, this study proposed a straightforward and practical method for bend scour simulation. The proposed simulation method is subdivided into three stages: two-dimensional flow simulation, general scour estimation, and bend scour estimation. A new bend-scour computation equation is proposed and incorporated into a two-dimensional hydraulic finite-volume model for simulating the evolution of bend scour depth around embankment toes. The proposed method is applied to simulate the temporal evolution of bend scouring near the Shuideliaw Embankment on the Cho-Shui River in Taiwan, where serious failure occurred during the June 2012 monsoon. Field data were gathered using the numbered-brick technique at the Shuideliaw Embankment to demonstrate the accuracy of the proposed method. The results of the bend scour simulations compared reasonably well with field measurements, indicating close agreement in terms of water levels and bend scour depths near the Shuideliaw Embankment. The proposed method was found to quickly estimate the maximum short-term general scour and bend scour depths for further enhancement of the safety of the embankment toe.

A lead zirconate titanate [PZT;Pb(Zr_0.52Ti_0.48)O₃] layer embedded infrared (IR) detector decorated with wavelength-selective plasmonic crystals has been investigated for high-performance non-dispersive infrared (NDIR) spectroscopy. A plasmonic IR detector with an enhanced IR absorption band has been designed based on numerical simulations, fabricated by conventional microfabrication techniques, and characterized with a broadly tunable quantum cascade laser. The enhanced responsivity of the plasmonic IR detector at specific wavelength band has improved the performance of NDIR spectroscopy and pushed the limit of detection (LOD) by an order of magnitude. In this paper, a 13 fold enhancement in the LOD of a methane gas sensing using NDIR spectroscopy is demonstrated with the plasmonic IR detector.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

The variability of ozone over Egypt has been studied in this work. Higher values of coefficient of variation (COV) at eight stations occur at winter while lowest values occur at summer. The COV is function of latitude in annual, winter and spring where it decreases gradually from the north to south of Egypt. The trend analysis of ozone over the eight stations indicates negative trends over northern stations for both annual and seasonal time series with the greatest one at winter. The horizontal distribution of ozone trend values is negative over all Egypt in winter while it positive over middle and south Egypt in the other seasons. The long-term variability of the behavior of the annual ozone shows positive trend values in ozone are the dominant features during the period 1979- 1989 at the most stations. Negative trend values in ozone are the dominant features during the period 1990- 2014 at all stations. The Mann–Kendall test confirms that there is an abrupt change towards decreasing of ozone occurs in 1981, 1984, 2012, 1999, 2000, 1998 and 2010, while a change towards increasing of ozone appears in 2006, 2014, 1993 and 1989.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.