The art work of this present paper is to show properly conditions and aspects to reach stability in the process control, as also to avoid instability, by using digital PID controllers, with the intention of help the industrial community. The discussed control strategy used to reach stability is to manipulate variables that are directly proportional to their controlled variables. To validate and to put the exposed principles into practice, it was done two simulations of a continuous fermentation tank process start-up with the yeast strain S. Cerevisiae NRRL-Y-132, in which the substrate feed stream contains different types of sugar derived from cane bagasse hydrolysate. These tests were carried out through the resolution of conservation laws, more specifically mass and energy balances, in which the fluid temperature and level inside the tank were the controlled variables. The results showed the facility in stabilize the system by following the exposed proceedings.

Several factors influence traffic congestion and overall traffic dynamics. Simulation modeling has been utilized to understand the traffic performance parameters during traffic congestions. This paper focuses on driver behavior of route selection by differentiating three distinguishable decisions, which are shortest distance routing, shortest time routing and less crowded road routing. This research generated 864 different scenarios to capture various traffic dynamics under collective driving behavior of route selection. Factors such as vehicle arrival rate, behaviors at system boundary and traffic light phasing were considered. The simulation results revealed that shortest time routing scenario offered the best solution considering all forms of interactions among the factors. Overall, this routing behavior reduces traffic wait time and total time (by 69.5% and 65.72%) compared to shortest distance routing.

The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

Industrial manipulators and parallel robots are often used for tasks like drilling or milling, that require three translational, but only two rotational degrees of freedom (“3T2R”). While kinematic models for specific mechanisms for these tasks exist, a general kinematic model for parallel robots is still missing. This paper presents the definition of the rotational component of kinematic constraints equations for parallel robots based on two reciprocal sets of Euler angles for the end-effector orientation and the orientation residual. The method allows to completely remove the redundant coordinate in 3T2R tasks and to solve the inverse kinematics for general serial and parallel robots with the gradient-descent algorithm. The functional redundancy of robots with full mobility is exploited using nullspace projection.

This paper aims at providing a multisource data analysis, including direct data collection, focussed on daily average distances covered with motorised mobility. Its results can be used as a basis for policies involving a shift towards new propulsions, electric motors or hybrid electric vehicles (HEV) for road vehicles. A number of variables influence the propensity of drivers to acquire or use electric traction, even the option of plug-in hybrid electric vehicles (PHEV). This paper addresses one of such variable: the compliancy of electric traction regarding both hybrid plug-in solutions and full-electric vehicles, in addition to the autonomy of batteries (range), with the daily travels by road vehicles, mainly by automobiles. We want to understand whether the constraints leading towards a greater independence from crude oil rather than constraints concerning emissions, mainly in urban contexts, might be compliant with the habitual daily trips of drivers. We also want to understand if these daily trips have varied much during recent years and the consequences they may have on operational costs of plug-in automobiles. We are well aware that the average distances do not represent the actual daily runs of vehicles; yet similar distributions of daily distances for different case studies indicate that a high percentage of trips respond to certain features. After introducing a general overview of road-motorised mobility in Italy, the paper compares data from other studies to provide an indication of average daily driving distances. This reveals how different recent analyses converge on a limited range of average road distances covered daily by Italians, which is compliant with ranges allowed by electric batteries, provided that their low energy density in comparison with that of oil-derived fuels do not imply a significant increase in vehicle mass. Subsequently, average distances in some EU Countries are taken from the literature, and the results are also compared with U.S. data. The study extends the analysis of trends on the use of automobiles and road-vehicles to the international context by also addressing average daily distances covered for freight transport in some EU Countries, thereby providing a further basis for comparison and for understanding whether the daily motorised mobility can be considered as a stable phenomenon. Finally, an analysis is provided of the economic operational advantages from using plug-in vehicles. The main aim of this paper is thereafter to investigate the average daily motorised mobility of single vehicles – so not an aggregated motorised mobility as collected by some statistics – by using private motorised vehicles in Italy, with related trends; thereafter, to compare these data with those obtained from other countries, making use of both existing research studies and directly collected data; the final aim is to understand both the compliance of daily activities based on the use of automobiles with the autonomy of batteries (range) and to calculate some economic outcomes.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

This study contributes to the literature by exploring challenges to implementing ISO 20000-1 in an emerging economy context, and suggests ways to overcome these challenges. A survey-based methodology was adopted. The data were analyzed using principal component analysis. The results indicated that senior management support was the most significant challenge for the successful implementation of IT Service Management (ITSM) systems. Other significant challenges were the justification of significant investment, premium customer support, co-operation and co-ordination among IT support teams, proper documentation, and effective process design The findings help managers introduce IT service management system (ISO 20000-1:2011) as well as improving IT service delivery system in IT support organizations for managing big data in an emerging economy. In the future, cross-firm and cross-country studies on challenges to ISO 20000 can be conducted. Also, interpretive structural model (ISM) can be formulated to examine the interrelationships among the identified challenges to ISO 20000.

In laser-assisted milling, higher temperature in shear zone softens the material potentially resulting in a shift of mean residual stress, which significantly affects the damage tolerance and fatigue performance of product. In order to guide the selection of laser and cutting parameters based on the preferred mean residual stress, inverse analysis is conducted by predicting residual stress based on guessed process parameters, which is defined as the forward problem, and applying iterative gradient search to find process parameters for next iteration, which is defined as the inverse problem. An analytical inverse analysis is therefore proposed for the mean residual stress in laser-assisted milling. The forward problem is solved by analytical prediction of mean residual stress after laser-assisted milling. The residual stress profile is predicted through the calculation of thermal stress, by treating laser beam as heat source, and plastic stress by first assuming pure elastic stress in loading process, then obtaining true stress with kinematic hardening followed by the stress relaxation. The variance-based recursive method is applied to solve inverse problem by updating process parameters to match the measured mean residual stress. Three cutting parameters including depth of cut, feed per tooth, and cutting speed, and two laser parameters including laser-tool distance and laser power, are updated with respected to the minimization of resulting residual stress and measurement in each iteration. Experimental measurements are referred on the laser-assisted milling of Ti-6Al-4V grade 5 and ELI. The percentage difference between experiments and predictions is less than 5% for both materials, and the selection is completed within 50 loops.

Considering the manufacturing of automotive components, there exists a dilemma around the substitution of traditional Cast Iron (CI) with lighter metals. Nowadays, aluminium alloys, being lighter compared to traditional materials, are considered as a more environmentally friendly solution. However, the energy required for the extraction of the primary materials and manufacturing of components is usually not taken into account in this debate. In this study, an extensive literature review has been performed to estimate the overall energy required for the manufacturing of an engine cylinder block using (a) cast iron and (b) aluminium alloys. Moreover, data from over 100 automotive companies, ranging from mining companies to consultancy firms, have been collected in order to support the soundness of this investigation. The environmental impact of the manufacturing of engine blocks made of these materials is presented with respect to the energy burden; the “cradle-to-grave approach” has been implemented to take into account the energy input of each stage of the component lifecycle starting from the resource extraction and reaching to the end-of-life processing stage. Our results indicate that although aluminium components contribute towards reduced fuel consumption during their use phase, the vehicle distance needed to be covered in order to compensate for the up-front energy consumption related to the primary material production and manufacturing phases is very high. Thus, the substitution of traditional materials with lightweight ones in the automotive industry should be very thoughtfully evaluated.

In a thin-volume photobioreactor where a concentrated suspension of microalgae is circulated throughout the established spatial irradiance gradient, microalgal cells experience a time-variable irradiance. Deploying this feature is the most convenient way of obtaining the so-called “flashing light” effect, improving biomass production in high irradiance. This work investigates the light flashing features of sloping wavy photobioreactors, a recently proposed type, by introducing and validating a Computational Fluid Dynamics model. Two characteristic flow zones (straight top-bottom stream and local recirculation stream), both effective toward light flashing, have been found and characterised: a recirculation-induced frequency of 3.7 Hz and straight flow-induced frequency of 5.6 Hz were estimated. If the channel slope is increased, the recirculation area becomes less stable while the recirculation frequency is nearly constant with flow rate. The validated CFD model is a mighty tool that could be reliably used to further increase the flashing frequency by optimising the design, the dimensions, the installation and the operational parameters of the sloping wavy photobioreactor.

Nitride and carbide are the second phases which play an important role in the performance of bearing steel, and their precipitation behavior is complicated. In this study, TiN-MC_x precipitations in GCr15 bearing steels were obtained by non-aqueous electrolysis, and their precipitation mechanisms were studied. TiN is the effective heterogeneous nucleation site for Fe₇C₃ and Fe₃C, therefore, MC_x can precipitate on the surface of TiN easily, its chemistry component consists of M₃C and M₇C₃ (M = Fe, Cr, Mn) and Cr₃C₂. TiN-MC_x with high TiN volume fraction, TiN forms in early stage of solidification, and MC_x precipitates on TiN surface after TiN engulfed by the solidification advancing front. TiN-MC_x with low TiN volume fraction, TiN and MC_x form in late stage of solidification, TiN can not grow sufficiently and is covered by a large number of precipitated MC_x particles.

Cloud-based CNC is an emerging paradigm of Industry 4.0 where computer numerical control (CNC) functionalities are moved to the cloud and provided to manufacturing machines as a service. Among many benefits, C-CNC allows manufacturing machines to leverage advanced control algorithms running on cloud computers to boost their performance at low cost, without need for major hardware upgrades. However, a fundamental challenge of C-CNC is how to guarantee safety and reliability of machine control given variable Internet quality of service, especially on public Internet networks. We propose a three-tier redundant architecture to address this challenge. We then prototype tier one of the architecture on a 3D printer successfully controlled via C-CNC over public Internet connections, and discuss follow-on research opportunities.

In the fashion field, the use of electroplated small metal parts such as studs, clips and buckles is widespread. The plate is often made of precious metal, such as gold or platinum. Due to the high cost of these materials, it is strategically relevant and of primary importance for manufacturers to avoid any waste by depositing only the strictly necessary amount of material. To this aim, Companies need to be aware of the overall number of items to be electroplated so that it is possible to properly set the parameters driving the galvanic process. Accordingly, the present paper describes a Machine Vision-based method able to automatically count small metal parts arranged on a galvanic frame. The devised method relies on the definition of a proper acquisition system and on the development of image processing-based routines. Such a system is then implemented on a counting machine is meant to be adopted in the galvanic industrial practice to properly define a suitable set or working parameters (such as current, voltage and deposition time) for the electroplating machine and, thereby, to assure the desired plate thickness from one side and to avoid material waste on the other.

Exoskeleton robots are a rising technology in industrial contexts to assist humans in onerous applications. Mechanical and control design solutions are intensively investigated to achieve a high performance human-robot collaboration (e.g., transparency, ergonomics, safety, etc.). However, the most of the investigated solutions involve high-cost hardware, complex design solutions and standard actuation. In the presented work, an industrial exoskeleton for lifting and transportation of heavy parts is proposed. A low-cost mechanical design solution is proposed, exploiting compliant actuation at the shoulder joint to increase safety and transparency in human-robot cooperation. A hierarchic model-based controller is then proposed (including the modeling of the compliant actuator) to actively assist the human while executing the task. An inner optimal controller is proposed for trajectory tracking, while an outer fuzzy logic controller is proposed to online deform the task trajectory on the basis of the human’s intention of motion. A gain scheduler is also designed to calculate the optimal control gains on the basis of the performed trajectory. Simulations have been performed in order to validate the performance of the proposed device, showing promising results. The prototype is under realization.

Future cyber-physical systems may extend over broad geographical areas, like cities or regions, thus requiring the deployment of large real-time networks. A strategy to guarantee predictable communication over such networks is to synthesize an offline time-triggered communication schedule. However, this synthesis problem is computationally hard (NP-complete), and existing approaches do not scale satisfactorily to the required network sizes. This article presents a segmented offline synthesis method which substantially reduces this limitation, being able to generate time-triggered schedules for large hybrid (wired and wireless) networks. We also present a series of algorithms and optimizations that increase the performance and compactness of the obtained schedules while solving some of the problems inherent to segmented approaches. We evaluate our approach on a set of realistic large-size multi-hop networks, significantly larger than those considered in the existing literature. The results show that our segmentation reduces the synthesis time up to two orders of magnitude.

The development of hydrogen plasma smelting reduction as a CO₂ emission-free steel-making process is a promising approach. This study presents a concept of the reduction of hematite using hydrogen thermal plasma. A laboratory scale and pilot scale hydrogen plasma smelting reduction (HPSR) process are introduced. To assess the reduction behavior of hematite, a series of experiments has been conducted and the main parameters of the reduction behavior, namely the degree of hydrogen utilization, degree of reduction and the reduction rate are discussed. The thermodynamic aspect of the hematite reduction is considered and the pertinent calculations have been carried out using FactSage^TM 7.2. The degree of hydrogen utilization and the degree of reduction were calculated using the off-gas chemical composition. The contribution of carbon, introduced from the graphite electrode, ignition pin and steel crucible, to the reduction reactions was studied. The degree of reduction of hematite, regarding H₂O, CO and CO₂ as the gaseous reduction products, is determined. It is shown that the degree of hydrogen utilization and the reduction rate were high at the beginning of the experiments, then decreased during the reduction process owing to the diminishing of iron oxide. Conducting experiments with the high basicity of slag B₂=2 led to a decrease of the phosphorus concentration in the produced iron.

When a railway vehicle moves on a curved rail, sliding contact occurs between the rail head side and wheel flange, which wears the wheel flange down. The thinned flange needs to be restored above the required minimum thickness for structural safety. In this study, a new process and welding wire for restoring worn-out railway wheels by submerged arc welding was developed. To characterize the properties of the restored wheel, dilatometric analysis of phase transformation, SEM/EDX analyses, hardness measurement, and residual stress measurement using the X-ray diffraction method were performed. Finally, wear tests with full-size wheel/rail specimens were carried out. It was confirmed that the weld metal was composed of bainitic microstructures as intended, and welding defects were not observed. The wear amount of the restored wheel was greater than that of the base material, but it was less than half of the wear depth of the weld-repaired wheel with ferritic–pearlitic microstructures. The developed process seems applicable to industry.

Engineering the supply chain requires a design that possesses the flexibility of a complex adaptive system, consisting of interlinking architecture, with external dimensions and system germane internal elements. The complexity of the subject, the multiple environments, dimensions, elements and concepts, require a research that does not set any limits to the conceptual, analytical or empirical nature of the existing approaches present in practice. This present the rational for applying a taxonomy approach to investigate the integration engineering of supply chain architecture, design and engineering, and building a framework for integrating the existing supply chain approaches. The objectives of this paper are to critically analyse the key supply chain concepts and approaches, to assess the fit between the research literature and the practical issues of supply chain architecture, design and engineering, and to develop a methodology that could be used by practitioners when integrating supply chain architecture and design with strategy engineering. Taxonomy approach is applied to consider criteria for strategy architecture, hierarchical strategy design, strategy engineering, and integration of supply chain architecture, design and engineering as a conceptual system. The results from this paper derived with the findings that the relationship between supply chain architecture, design and engineering is weak and challenges remain in the process of adapting and aligning operations. This paper also derived with a novel approach for addressing these obstacles, based on a new methodology. The novelty that derives from this paper is a methodology for integrating supply chain architecture, design and engineering, with criteria that enable decomposing and building a digital (new and non-existent) supply chain as a system. The paper revealed a number of tools and mechanism which enabled the development of a new methodology for integrating the architecture, design and engineering of a supply chain. The review derived with improvements to current and existing theories for analysing interdependencies within and between their individual contexts. This issue is addressed with a hierarchical method for network design, applied for building and combining the integration criteria.

This paper outlines a new methodology for developing strategy for supply chain integration of Autonomous Electrical Vehicles (AEV) to the Internet of Things (IoT). The methodology consists of external architecture and internal design that anticipates the business strategy in the development process. The methodology is designed to anticipate the impact of developments in new road transport technologies, such as Tesla Truck or Tesla Pickup. Since the methodology is designed to anticipate the impact of non-existing technologies, it represents green-field analysis. Green-field is defined as a new and non-existent operation. Green-field strategy architecture in this paper is presented as a process of accepting the world and acting upon that version of the world. The results of the analysis are presented as pathways and outcomes, emerging from the interrelated relationship between AEV and IoT. The emerging methodology is applied through two case studies to evaluate the impact to environment, performance and operationalisation. The methodology proposes architecture and design for integrating AEV and IoT in the supply chain strategy, and a set of new evaluation criteria that promote acceptance of Artificial Intelligence (AI) in the design process. The main contribution to knowledge is a new methodology for integrating AEV and the IoT to the supply chains. The paper applies interplay between inductive and deductive case study and grounded theory approach to build upon the concept of supply chain architecture and contribute to knowledge to the topic of formulating green-field integrated AEV- IoT supply chain strategy.

The Internet-of-Things (IoT) enables enterprises to obtain profits from data but triggers data protection questions and new types of cyber risk. Cyber risk regulations for the IoT however do not exist. The IoT risk is not included in the cyber security assessment standards, hence, often not visible to cyber security experts. This is concerning, because companies integrating IoT devices and services need to perform a self-assessment of its IoT cyber security posture. The outcome of such self-assessment need to define a current and target state, prior to creating a transformation roadmap outlining tasks to achieve the stated target state. In this article, a comparative empirical analysis is performed of multiple cyber risk assessment approaches, to define a high-level potential target state for company integrating IoT devices and/or services. Defining a high-level potential target state represent is followed by a high-level transformation roadmap, describing how company can achieve their target state, based on their current state. The transformation roadmap is used to adapt IoT risk impact assessment with a Goal-Oriented Approach and the Internet of Things Micro Mart model. The main contributions from this paper represent a transformation roadmap for standardisation of IoT risk impact assessment; and transformation design imperatives describing how IoT companies can achieve their target state based on their current state with a Goal-Oriented approach. Verified by epistemological analysis defining a unified cyber risk assessment approach. These can be used for calculating the economic impact of cyber risk; for international cyber risk assessment approach; for quantifying cyber risk; and for planning for impact of cyber-attacks, e.g. cyber insurance. The new methods presented in this paper for applying the roadmap include: IoT Risk Analysis through Functional Dependency; Network-based Linear Dependency Modelling; IoT risk impact assessment with a Goal-Oriented Approach; and a correlation between the Goal-Oriented Approach and the IoTMM model.

This paper developed a new theory for supply chain architecture, and engineering design that enables integration of the business and supply chain strategies. The architecture starts with individual supply chain participants and derives insights into the complex and abstract concept of green-field integration design. The paper presented a conceptual system for depicting the interactions between business and supply chain strategy engineering. The system examines the decisions made when engineering the business strategy, with regards to the supply chain design. The system derived with a new understanding of how strategies are integrated, and what are the implications for engineering successful strategies. The study revealed that supply chain design is not considered in great detail before architecting the business strategies. Thus, companies consequentially experience supply chain problems that are likely to be detrimental to the growth potentials. The paper also derived with the findings that proactive and pre-emptive involvement of supply chain participants in the strategy engineering process, would lead to a more robust strategic design.

The focus of this paper is on supply chain strategy formulation. A conceptual theory approach is used for investigating and identifying the relationship between multiple elements, dimensions, forces and factors that influence and affect the supply chain strategy formulation in Greenfield context, specific to the slate mining industry. The research study involved secondary data review and series of 20 qualitative interviews, followed by 2 group discussions, one with mining and transportation experts external to the supply chain and one group discussion with supply chain internal experts. Through critical analysis, a number of problems emerge and the process of addressing these problems, results in a new framework for evaluating the relationship between business and supply chain strategy, specific to Greenfield project and integration design context.

A Micro holes in a diamond are presented by using a homemade femtosecond (fs) Yb:KGW laser. An fs laser source was used emitting pulse duration of 230 fs at 1030 nm wavelength, whereas the spot size amounted to 8.9 μm. Parameters like pulse energy, and pulse number were varied over a wide range in order to evaluate their influence both on the micro hole geometry like hole diameter, circularity, taper angle, and on the drilling quality. Hourglass-shaped micro holes whose diameters decrease and increase again after a certain depth have important applications. The results demonstrate the feasibility of extending the drilling of an hourglass-shaped hole in a diamond sample, which has similar diameters at the hole entrance (92 μm) and exit (95 μm), but a much smaller diameter (28 μm) at a certain waist section inside the hole.

Objective:The application of information technology (IT( is fundamental in the hospitals to stay competitive.In this regard, recognizing the main risks to the implementation of IT in hospitals can provide vastopportunities to improve its efficiency and help to make strategic decisions. This study aimed tosearch for the main risks of implementation of IT projects in the hospitals of Tehran. Methods: This was a practical and cross-sectional study which was conducted in the 18 hospitals of Tehran,Iran, 2018; in which a sample of 65 members were studied. The required data were collected using a questionnaire to examine seven main risks, including market, project management, human resources, technical, organizational, financial, strategic risks. The collected data were analyzed using SPSS 19.0. Additionally, the method used to test the risks in this study was structural equation modeling, which was ran using LISREL 9.30. Results: The results showed that among the seven main risks of to the implementation of IT in hospitals, the highest and lowest means were related to the human resource risks and the market risks, respectively. Also, according to the SEM, human resource risks and market risks had the highest and lowest effects, respectively. Conclusion: Announcing the use of IT in the hospitals, holding conferences about new IT developments with employees, suitable training, encouraging them to use IT tools, providing a motivating atmosphere to use IT tools for employees, are a few effective ways of overcoming the human resource risks.

The NCO functional group of 3-isocyanatoproply triethoxysilane (IPTS) and the OH functional group of DOPO-BQ were used to conduct an addition reaction. Following completion of the reaction, triglycidyl isocyanurate (TGIC) was introduced to conduct a ring-opening reaction. Subsequently, a sol-gel method was used to take place a hydrolysis- condensation reaction on TGIC-IPTS-DOPO-BQ to form a hyperbranched nitrogen–phosphorous–silicon (HBNPSi) flame retardant. This flame retardant was incorporated into a polyurethane (PU) matrix to prepare a hybrid material. Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), limiting oxygen index (LOI), UV-VIS spectrophotometry, and Raman analysis were conducted to structure characterization and analyzed transparency, thermal stability, flame retardancy, and residual char to understand the flame retardant mechanism of prepared hybrid materials. After the flame retardant was added, the maximum degradation rate decreased from −36 wt%/min to −17 wt%/min, the integral procedure decomposition temperature (IPDT) increased from 348 ℃ to 488 ℃, and the char yield increased from 0.7 to 8.1 wt%. The aforementioned results verified that thermal stability of PU can be improved after adding HBNPSi. The LOI analysis indicated that the pristine PU was flammable because the LOI of pristine PU was only 19. When the content of added HBNPSi was 40%, the LOI value was 26; thus the PU hybrid became nonflammable.

Digital technologies have changed the way supply chain operations are structured. In this article, we develop design principles to show determining factors for an Internet-of-Things approach within Supply Chain Management. From the design principles, the article derives a new model for the Industrial Internet of Things supply chains. The focus is on Small and Medium Enterprises (SMEs). This research design results in a new process of compounding knowledge from existing supply chain models and adapting the cumulative findings to the concept of supply chains in the Industrial Internet of Things. The paper outlines the design principles for developing cognition in the process of integrating SME’s digital supply chains in the Industrial Internet of Things (IIoT) and the Industry 4.0 (I4.0).

In this paper we describe many important aspects connected with lubricants, namely: the most cheapest organic lubricant in the word, how effectively save lubricant between pairs of friction, what kind of rational shapes for the lubricant must be, what it will be connected with wear and tear using the new organic lubricant (for this purpose formulas and curves are shown in computer program MathCad with calculation). Moreover, there is one physical model which helps to catch car exhausted gases. In conclusion, some recommendations will be given to realize them into the practice during the operation for the different mechanisms including ecology.

The dye effluent is usually difficult to be degraded by conventional wastewater treatment in leather industry. In order to develop efficient and cost-effective treatment methods, we evaluate the effect of white-rot fungus immobilization for dye decolorisation in this paper. The Phanerochaete chrysosporium BKM-F-1767 was used for immobilization. This research found that the white-rot fungus immobilization had an obviously decolorisation effect in dye wastewater treatment, and plant carriers such as sorghum stalk and corn cob were helpful to the growth of Phanerochaete chrysosporium in white-rot fungus immobilization. Due to the stability and recyclability, the white-rot fungus co-immobilization was considered as the most suitable treatment for decolorisation of dye effluent which enjoyed the advantages of both adsorption immobilization and entrapment immobilization. Furthermore, the dye decolorisation evaluation was carried out to find the most suitable carrier for co-immobilization, and it found that sorghum stalk - calcium-alginate gel spherical particle (SS-CGPB) has better decolorisation effect than corn cobs - calcium-alginate gel spherical particle (CC-CGPB), and the dye decolorisation rate was 86.77%. After 5 cycles, the dye decolorisation rate was 85.87% which indicated the SS-CGPB preserved functional integrity successfully. By further analyzing the biodegradation process with white-rot fungus immobilization, the intermediate products were observed and the degradation pathway of acid golden yellow dye molecular was proposed. The results showed that the C-N single bonds attached to the central benzene in the dye molecule were attacked and destroyed in white-rot fungus co-immobilization treatment, thus the structure of dye molecule could be successfully degraded into small molecules which would be more easily treated by conventional treatment methods. Therefore, the white rot fungus co-immobilization might be appropriate for pre-treatment as an important biotechnology for the advanced treatment of dye effluent.

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

The energy efficiency of grinding depends on the appropriate selection of cutting conditions, grinding wheel and workpiece material. Additionally, the estimation of specific energy consumption is a good indicator to control the energy consumed during the grinding process. Consequently, this study develops a model of material removal rate to estimate the specific energy consumption based on the measurement of active power consumed in a plane surface grinding of C45K with different thermal treatments and AISI 304. This model identifies and evaluates the power dissipated by sliding, ploughing and chip formation in a industrial-scale grinding process. Furthermore, the instantaneous positions of the abrasive grains during cutting are described to study the material removal rate. The estimation of specific chip formation energy is similar to that described by other authors in laboratory scale, which allows to validate the model and experiments. Finally, the results show that the energy consumed by sliding is the main phenomenon of energy dissipation in industrial-scale grinding process, where it is denoted that sliding energy by volume unity decreases as the depth of cut and speed of workpiece increase.

Two major sample configurations are adopted in all the instruments for fabric hand measurement, flat sample as in KES and FAST types machines, and wrinkled sample as in PhabrOmeter. This paper compares the two sample types to examine which one if any offers a better coverage and reflection of the fabric sensory attributes. Fabrics have unique behaviors of drape, wrinkle and tactile sense which are entirely due to the simultaneous occurrence of both in-plane membrane deformation and out-of-plane bending deformation in multiple curvature. Such singular deformation mode cannot be detected by any machines using flat sample, whereas during a PhabrOmeter test, the fabric sample genuinely produces drape, wrinkle in addition to other related deformations. This paper then introduced the theoretical research pertaining to the measurement. Then a split sample experiment is conducted to demonstrate the importance of the internal connections in fabric during drape and wrinkle processes. As such fabric interconnection will be barely disclosed during tests using flat samples, another important advantage of PhabrOmeter is hence clearly shown.

In the industrial sector, the financial gain is generally considered at the cost of environmental degradation. The environmental protection and economic benefit are common conflicting objectives in many optimization problems. In any multi-criteria problem, the most challenging part is to optimize the conflicting goals. But if these objectives become non-conflicting, then the problem can be solved with ease. This paper is all about minimizing the environmental impact of industrial processes while maximizing the net economic benefit. There is a general misconception of linking the environmental protection with a financial loss. This is not always true; the Eco-Efficiency or Cleaner Production Technology (CPT) is a perfect example to disprove this notion. Economics of CPT regarding water savings for the textile-processing sector in Pakistan has been analyzed in this paper. Changes in water use before and after the implementation of water conserving technologies in the textile sector of Pakistan from a study conducted by the Cleaner Production Institute (CPI) are utilized to perform a cost-benefit analysis. Direct financial benefits that could be achieved through the application of these technologies are presented only. Other environmental benefits, though not described here, are of no less importance. The study results reveal that very high potential of water savings exists for most of the investments on CPT.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In-process EBM monitoring for quality assurance purposes has been a popular research area. Electronic imaging has recently been investigated as one of the in-process EBM data collection methods, alongside thermal/ optical imaging techniques. Despite certain capabilities of an electronic imaging system have been investigated, experiments are yet to be carried out to benchmark one of the most important features of any imaging systems – spatial resolution. This article addresses this knowledge gap by: (1) proposing an indicator for the estimation of spatial resolution which includes the Backscattered Electrons (BSE) information depth, (2) estimating the achievable spatial resolution when electronic imaging is carried out inside an Arcam A1 EBM machine, and (3) presenting an experimental method to conduct edge resolution evaluation with the EBM machine. Analyses of experimental results indicated that the spatial resolution was of the order of 0.3mm-0.4mm when electronic imaging was carried out at room temperature. It is believed that by disseminating an analysis and experimental method to estimate and quantify spatial resolution, this study has contributed to the on-going quality assessment research in the field of in-process monitoring of the EBM process.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In EBM process monitoring, data analysis for processed layer quality evaluation is currently focused on the extraction of information from the raw data collected in-EBM process, i.e. thermal/ optical / electronic images, and the comparison between the collected data and the Computed Tomography (CT)/ microscopy images generated post-EBM process. This article postulates that a stack of bitmaps could be generated from the 3D model at a range of Z heights during file preparation of the EBM process, and serve as a reference image set. In-EBM process comparison between that and the workpiece images collected during the EBM process could then be used for quality assessment purposes. In addition, despite the extensive literature on 3D model slicing and contour generation for AM process preparation, no methods regarding image generation from cross sections of the 3D models have been disseminated in details. This article aims to address this by presenting a piece of 3D model-image generation software. The software is capable of generating binary 3D model reference images with user-defined Region-of-Interest (ROI) of the processing area, and Z heights of the model. It is envisaged that this 3D model-reference image generation ability opens up new opportunities in quality assessment for the in-process monitoring of the EBM process.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.

There is increasing use of wood-based composites in industry not only because of the shortage of solid wood, but above all for their better properties such as: strength, aesthetic appearance, etc. compared to wood. Medium density fibreboard (MDF) is a wood-based composite that is widely used in the furniture industry. The goal of the research conducted was to determine the effect of the type of coating on the drill cutting blades on the value of thrust force (F_t), cutting torque (M_c), cutting tool temperature (T) and surface roughness of the hole in drilling MDF panels. In the tests three types of carbide drills (HW) were used: not coated, TiAlN coated and ZrN coated. The measurement of both the thrust force and the cutting torque was carried out using an industrial piezoelectric sensor. The temperature of the cutting tool in the drilling process was measured using an industrial temperature measurement system using a K-type thermocouple. It was found that the value of the maximum temperature of the tool in the drilling process depends not only on the cutting speed and feed rate, but also on the type of coating of the cutting tool. The value of both the cutting torque and the thrust force is significantly influenced by the value of the feed rate and the type of drill coating. The effect of varying plate density on the surface roughness of the hole and the variation of the value of the thrust force is also discussed. The results of the investigations were statistically analysed using a multi-factorial analysis of variance (ANOVA).

To improve the effect of multi-point stretch forming of sheet metal, it is proposed in this paper to replace fixed ball head with swinging ball head. According to the multi-point dies with different arrangements, this research establishes the finite element models of the following stretch forming, i.e. fixed ball heads with conventional arrangement, swinging ball heads with conventional arrangement, swinging ball heads with declining staggered arrangement, and swinging ball heads with parallel staggered arrangement and then numerical simulation is performed. The simulation results show that by replacing fixed ball head with swinging ball head, the surface indentation of the formed part was effectively suppressed, the stress and tension strain distribution of the formed part was improved and the forming quality was improved; that the thickness of the elastic pad was reduced, the springback was reduced and the forming accuracy was improved; and that when the ball head was applied to multi-point die with staggered arrangement, better forming result was achieved, where the best forming result was achieved in combining the swinging ball heads with the multi-point die with parallel staggered arrangement. The forming experiments were carried out, and the experimental results were consistent with the trend of numerical simulation results, which verified the correctness of the numerical simulation.

The increased consumption of food requiring thermoformed packaging means that the packaging industry demands customized solutions in terms of shapes and sizes to make the packaging unique. In particular, the food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product features they contain. However, in turn, the differentiation of products is sought through the geometry and final finish of the product, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve physical properties, however they also affect the final aesthetics of the product. In accordance with this, this research study analyses by studying the mechanical properties of different relief geometries that can affect not only the aesthetics but also their strength. For this purpose, tensile and compression tests have been carried out. The results provide comparative data on the reliefs studied and show that there are different shapes, sizes and layout.

In the context of food packaging design, customization enhances the value of a product by meeting the needs of the consumer. Personalization is also linked to adaptation. This makes it possible to improve the properties of the packaging from various points of view: functional, aesthetic, economic and ecological. Currently the functional and formal properties of packaging are not investigated among themselves, however the study of both properties are the basis for creating a new concept of personalized and sustainable product. In accordance with this approach, the conceptual design procedure of packaging with personalized and adapted geometries based on the digitization of fresh food is proposed in this work. This study is based on the application of advanced technologies for the design and development of food packaging, in this case apples, in order to improve the quality of the packaging. The results obtained show that it is possible to use advanced technologies in the early stages of product design in order to obtain competitive products adapted to new emerging needs.

Low-cost RGB-D cameras are increasingly used in several research fields including human-machine interaction, safety, robotics, biomedical engineering and even Reverse Engineering applications. Among the plethora of commercial devices, the Intel RealSense cameras proved to be among the best suitable devices, providing a good compromise between cost, ease of use, compactness and precision. Released on the market in January 2018, the new Intel model RealSense D415 has a wide acquisition range (i.e. ~160-10000 mm) and a narrow field of view to capture objects in rapid motion. Given the unexplored potential of this new device, especially when used as a 3D scanner, the present work aims to characterize and to provide metrological considerations on the RealSense D415. In particular, tests are carried out to assess the device performances in the near range (i.e. 100-1000 mm). Characterization is performed by integrating the guidelines of the existing standard (i.e. the German VDI/VDE 2634 part 2 normative) with a number of literature-based strategies. Performance analysis is finally compared against latest close-range sensors, thus providing a useful guidance for researchers and practitioners aiming to use RGB-D cameras in Reverse Engineering applications.

The use of high strength to weight ratio laminated composites is emerging in marine industry and applications as a very efficient solution for improving productivity. Nevertheless, delamination between the layers is a limiting factor for the wider application of laminated composites, as it reduces the stiffness and strengths of the structure. Interleaving nanofibrous mats between layers of composite laminates has been proved to be an effective method for improving composites delamination resistance. This paper aims to characterize the effect of interleaved nanofiber on mode I interlaminar properties and failure mechanisms when subjected to static and fatigue loadings. For this purpose, virgin and nanomodified woven laminates were subjected to Double Cantilever Beam (DCB) specimens. Static and fatigue tests were performed and the tests were monitored by acoustic emission technique. The mechanical results showed a 130% increase of delamination toughness for nanomodified specimens in the static loadings and more crack growth resistance in the fatigue loading. The AE results revealed that different type of failure mechanisms was the cause of these improvements for the modified specimens compared with the virgin ones.

Facing with errors of a product after machining was a big title in this field. That will affect to product’s quality with unpredictable situation when products is in use for some particular application such as in medical facilities. Improving the precision of machine tools by exploring temperature on multiple points and measuring differential locations of the spindle is going to be executed in this study. A temperature measurement tool and a software running on Windows platform have been developed and combining with Non-bar system in order to support analyzing the temperature rising with the changes of length of the spindle to find the compensation solution based on eccentricity and length distortion. In this study, the whole tests have done on UX300 five – axis CNC machine tools for this investigation and the errors after applying compensation function have reduced 70% at least, with respect to the errors after machining without using compensation function.

This report describes the collection of a large dataset (6930 measurement) on dimensional error in the fused deposition modeling (FDM) additive manufacturing process for full-density parts. Three different print orientations were studied, as well as seven raster angles (0°, 15°, 30°, 45°, 60°, 75°, and 90°) for the rectilinear infill pattern. All measurements were replicated ten times on ten different samples to ensure a comprehensive dataset. Eleven polymer materials were considered: acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high-temperature PLA, wood-composite PLA, carbon-fiber-composite PLA, copper-composite PLA, aluminum-composite PLA, high-impact polystyrene (HIPS), polyethylene terephthalate glycol-enhanced (PETG), polycarbonate, and synthetic polyamide (nylon). The samples were ASTM-standard impact testing samples, since this geometry allows the measurement of error on three different scales; the nominal dimensions were 3.25mm thick, 63.5mm long, and 12.7mm wide. This dataset is intended to give engineers and product designers a benchmark for judging the accuracy and repeatability of the FDM process for use in manufacturing of end-user products.

This work studied the corrosion of welded pipes and how welding destroyed surface film of pipes. Surface reaction of a welded pipe is key to understanding phenomena and important factors during the corrosion. This paper presents experiment and CFD modeling approaches of a welded pipe corrosion under salt vapor condition. The pipes were welded at currents of 60 A,70 A and 80 A to observe the effect of welding current on corrosion. A welded pipe is a stainless-steel ASTM A312 grade 304L and period of experiment about 0-600 hours that they are tested in vertical and horizontal alignments. In CFD software, there is not direct model of corrosion but it can use surface reaction and create add-on species and chemical reaction technique for imitating the corrosion mechanism. The modeling approaches of corrosion have presented in 3-dimensional transient times in CFD simulation. Surface reactions were performed by Species Model which involve site species. Site species in Species Model took place at gas-solid interfaces and in this case are salt vapor and surface pipe. Chemical reaction rate on the surface controls lost weight of a welded pipe and the model can be validated with experiment. In conclusion, in period 0-600 hours error between CFD modeling and experiment have error trend decreased. The error at 600 hours is 6% both of vertical pipe and horizontal pipe test. The modeling approaches closely with the performed experiment and can be accepted. Moreover, the model is able to predict corrosion of a welded pipe of different sizes and their lost weight after 600 hours without experiment. Also the model can predict lifetime of pipe.

Face milling is a well known commercial process highly used in heavy industries that consumes high amount of power. Besides power issue, modern manufacturing industries are aiming for per part cost reduction keeping the product quality unimpaired. Unexpectedly if the part is rejected in any stage of manufacturing, the cost of manufacturing dramatically increases. Major cause of part rejection is excessive tool wear that imparts poor surface profile or catastrophic tool failure that causes adherence of broken tool debris onto machined surface. Furthermore, the tool wear is associated with sliding distance (frictional distance) and the tool life quantifies the cost of tools. As such, from the perspective of manufacturing industries it is imperative to optimize the surface quality parameter, cost of part, power consumption, and material removal – this is exactly what is accomplished here. By this work, it is possible to conserve power consumption, produce parts with lower cost, manufacture with uncompromising surface quality and enhanced material removal rate. Moreover, as intermediate factors of interest, the influences of sliding distance, tool life and tool flank wear on the overall machining performance are evaluated. The multi-objective optimization by Grey Relational Analysis (GRA) revealed that for improved product performance and fast manufacturing (case 1) optimum results are: feed per tooth fz = 0.25 mm/tooth, cutting speed vc = 392.6 m/min and cutting length l = 0.5 mm; for resource conservation (case 2) the optimum results are: feed per tooth fz = 0.125 mm/tooth, cutting speed vc = 392.6 m/min, cutting length l = 0.5 mm.

As an essential synthetic material used in continuous casting of steels, mold fluxes improve the surface quality of steel slabs. In this study, a CaO-SiO₂-Na₂O based low-fluorine mold flux was solidified by an improved water-cooled copper probe with different temperatures of molten flux and different probe immersion times. The heat flux through solid films and the film structures were calculated and inspected, respectively. The results indicate: large internal cracks (formed in the glassy layer of films during solidification) were observed, the formation and evolution of those cracks contributed to the the unstable heat flux density. The roughness of the surface in contacted with the water-cooled copper probe formed as films were still glassy and the roughness have no causal relationship with crystallization or devitrification. Combeite with columnar and faceted dendritic shapes is the main crystal in the film.

Machines for direct digital inkjet printing on cylindrical containers are a new technology out on the market. Their commercialization in the industrial sector has been affected by their high precision. This leads to the use of mechanisms with narrow manufacturing tolerances and to the search for topologies that have the least accumulated error without affecting quality. Machines with topologies to work on flat substrates have printing and productivity problems working on cylindrical substrates. This research paper presents the qualitative design of a direct digital inkjet printer working over cylindrical substrates comparing five mechanical topologies; three topologies with radial distribution and two topologies with parallel distribution. The aim of these topologies is to find the precision, quality and efficiency of the printer taking into account the restrictions present in its construction. Each topology has separate constitutive mechanisms, it is analyzed the tolerance ranges between the print head and the substrate whose cumulative error maximizes the inkjet print resolution to determine precision. From five Topologies, number 1, 2 and 5 meet the requirements. the topology 2 meets the requirements but it is not able to be developed due to current technological limitations.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

Many manufacturing sectors require high surface finishing. After machining operations such as milling or drilling, undesirable burrs or insufficient edge finishing may be generated. For decades, many finishing processes have been handmade-basis; this fact is accentuated when dealing with complex geometries especially for high value-added parts. In recent years, it’s a tendency of trying to automate as far as possible this kind of processes, repeatability and time/money savings are main purposes. Based on that idea, the aim of this work is to check new tools and strategies for finishing aeronautical parts, especially critical engine parts made on Inconel 718, a very ductile nickel alloy. Automating edge finishing of chamfered holes is a complicated but really important goal. In this paper, flexible abrasive tools were used for this purpose. A complete study of different abrasive possibilities was carried out, mainly focusing on roughness analysis and final edge results obtained.

The incorporation of plastic matrix composite materials into structural elements of the aeronautical industry requires contour machining and drilling processes along with metallic materials prior to final assembly operations. These operations are usually performed using conventional techniques, but they present problems derived from the nature of each material that avoid implementing One Shot Drilling strategies that work separately. In this work, the study focuses on the evaluation of the feasibility of Abrasive Waterjet Machining (AWJM) as a substitute for conventional drilling for stacks formed of Carbon Fiber Reinforced Plastic (CFRP) and aluminum alloy UNS A97050 through the study of the influence of abrasive mass flow rate, traverse feed rate and water pressure in straight cuts and drills. For the evaluation of the straight cuts, Stereoscopic Optical Microscopy (SOM) and Scanning Electron Microscopy (SEM) techniques are used inspection techniques have been used. In addition, the kerf taper through the proposal of a new method and the surface quality in different cutting regions have been evaluated. For the study of holes, the macrogeometric deviations of roundness, cylindricity and straightness have been evaluated. Thus, this experimental procedure reveals the conditions that minimize deviations, defects, and damage in straight cuts and holes obtained by AWJM.

The optimization of the production process of metal mines has been traditionally driven only by economic benefits while ignoring resource efficiency. However, it has become increasingly aware of the importance of resource efficiency since mineral resource reserves continue to decrease while the demand continues to grow. To better utilize the mineral resources for sustainable development, this paper proposes a multi-objective optimization model of the production process of metal mines considering both economic benefits and resource efficiency. Specifically, the goals of the proposed model are to maximize the profit and resource utilization rate. Then, the fast and elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II) is used to optimize the multi-objective optimization model. The proposed model has been applied to the optimization of the production process of a stage in the Huogeqi Copper Mine. The optimization results provide a set of Pareto-optimal solutions that can meet varying needs of decision makers. Moreover, compared with those of the current production indicators, the profit and resource utilization rate of some points in the optimization results can increase respectively by 2.99% and 2.64%. Additionally, the effects of the decision variables (geological cut-off grade, minimum industrial grade and loss ratio) on objective functions (profit and resource utilization rate) were discussed using variance analysis. The sensitivities of the Pareto-optimal solutions to the unit copper concentrate price were studied. The results show that the Pareto-optimal solutions at higher profits (with lower resource utilization rates) are more sensitive to the unit copper concentrate prices than those obtained in regions with lower profits.

The UK food industry faces significant challenges to remain sustainable. With major challenges such as Brexit on the horizon, companies can no longer rely on a low labour cost workforce to maintain low production costs and achieve economic sustainability. Smart Systems (SS) is being seen as an approach towards achieving significant improvements in both economic and environmental sustainability. However, there is little evidence to indicate whether UK food companies are prepared for the implementation of such systems. The purpose of this research is to explore the applicability of Smart Systems in UK food manufacturing companies and, to identify the key priority areas and improvement levers for the implementation of such systems. A triangulated primary research approach is adopted and includes a questionnaire, follow up interviews and visits to thirty-two food manufacturing companies in the UK. The questionnaire and interviews are guided by the development of a unique measuring instrument created by the authors that is focusses upon SS technologies and systems. This paper makes an original contribution in that it is one of few academic studies to explore the implementation of SS in the industry and, provides a new perspective on the key drivers and inhibitors around its implementation. Findings suggest that the current turbulence in the industry could be bringing food companies closer to the adoption of such systems, hence it is a good time to define and develop the optimum SS implementation strategy.

Mixing is considered as a critical process parameter (CPP) during process development due to its significant influence on reaction selectivity and process safety. Nevertheless, mixing issues are difficult to identify and solve owing to their complexity and dependence on knowledge of kinetics and hydrodynamics. In this paper, we proposed an optimization methodology using Computational Fluid Dynamics (CFD) based compartmental modelling to improve mixing and reaction selectivity. More importantly, we have demonstrated that through the implementation of surrogate-based optimization, the proposed methodology can be used as a computationally non-intensive way for rapid process development of reaction unit operations. For illustration purpose, reaction selectivity of a process with Bourne competitive reaction network is discussed. Results demonstrate that we can improve reaction selectivity by dynamically controlling rates and locations of feeding in the reactor. The proposed methodology incorporates mechanistic understanding of the reaction kinetics together with an efficient optimization algorithm to determine the optimal process operation and thus can serve as a tool for quality-by-design (QbD) during product development stage.

Retail buildings can provide energy flexibility to the grid with the possibility of load shifting and building automation systems. Demand response is a collective innovation in the smart grid domain. Various stakeholders should be involved in the demand response activities to ensure the success. The owners or senior management of retail buildings need to consider the stakeholders who are directly influenced by the demand response participation, e.g. customers and employees. Meanwhile, demand response activities are influenced by various factors, such as energy market structure, policy, etc. Therefore, this paper investigates the demand response readiness for retail buildings with three aspects: energy control preferences, stakeholder engagement, and cross-national differences. A questionnaire is designed and collected with store managers in Denmark (N=51) and the Philippines (N=36). The result shows that: 1) retail stores are much readier to participate in the implicit demand response by manual energy control compared to the utility control or building automation. Meanwhile, store managers have significant concerns about business activities and indoor lighting compared to other aspects; 2) the statistically significant influential factors for retail stores to participate in the demand response are related to whether the DR participation matches the company goals, influences business operation, and whether retail stores are lack of related knowledge; 3) retail stores believe that stakeholders should be informed about the DR activities but not involved in; 4) there are significant differences regarding the energy control preferences and concerns between retail stores in Denmark and the Philippines, but no significant difference regarding the stakeholder engagement.

Hybrid machine tools combining additive and subtractive processes have arisen as a solution to the increasing manufacture requirements, boosting the potentials of both technologies, while compensating and minimizing their limitations. Nevertheless, the idea of hybrid machines is relatively new and there is a notable lack of knowledge in the field. Therefore, in the present paper, an insight into the advancements of hybrid machines is given, identifying their real capabilities, together with the latest developments from an industrial context. In addition, the current situation and future perspectives of hybrid machines from the point of view of process planning, monitoring and inspection are discussed. Finally, the challenges that must be overcome and the opportunities that the hybrid machines will provide in the forthcoming years are presented.

In this paper, the fatigue response of Fused Filament Fabrication (FFF) Acrylonitrile butadiene styrene (ABS) parts is studied. Different building parameters (layer height, nozzle diameter, infill density, and printing speed) were chosen to study their influence on the lifespan of cylindrical specimens according to a design of experiments (DOE) using the Taguchi methodology. The same DOE was applied on two different specimen sets using two different infill patterns: rectilinear and honeycomb. The results show that infill density is the most important parameter for both studied patterns. The specimens manufactured with the honeycomb pattern show longer lifespans. The best parameter set associated to that infill was chosen for a second experimental phase, in which the specimens were tested under different maximum bending stresses to construct the Wöhler curve associated to this 3D printing configuration. The results of this study are useful to design and manufacture ABS end-use parts that are expected to work under oscillating periodic loads.

The present work aims at the comprehensive application of stochastic and optimization tools with the support of Information and Communication Technologies (ICT) through a case study in a logistics process for electronic goods; simulation and Response Surface Methodology (RSM) are applied for this purpose. The problem to be evaluated is to define an optimal distribution cost for products shipped to wholesale customers located in different cities in Mexico from a manufacturing plant in Tijuana, Mexico. The factors under study are the product allocation for each distribution center, finished good inventory level and on time deliveries, which are supposed to be significant to get the objective. The methodology applied for this problem considers the design of a discrete event simulation model to represent virtually the real life of logistics process, which is considered a complex system due to different activities are interrelated to carry it out. This model is used to execute the different experiments proposed by the RSM. The results obtained from simulation model were analyzed with the RSM to define the mathematical model that allows identifying the parameters of the factors in order to optimize the process. The findings prove how the ICT facilitate the application of stochastic tools with the purpose of process optimization.

Sustainability in material purchasing is a growing area of research. Goods purchasing decisions strongly affect transportation path flows, vehicle consolidation, inventory levels and related obsolescence costs. Within a global sourcing context, companies experience the need of new decision making approaches capable to consider a large variety of factors, also linked with society and environment. Environmental impact assessment has become a key requirement for materials purchasing and transportation decisions since global warming is a rising concern both in academic and industrial researches. In fact, it is well known that the freight transport industry is responsible for large amounts of carbon emissions contributing to global warming. In this paper, we initially analyse and compare the environmental economic policies established by the International Governments in relation to the carbon trading systems adopted. Then, we develop a multi-objective lot sizing approach useful in practice to define the sustainable quantity to purchase when a Cap and Trade mitigation policy is present. We further analyse the model behaviour according to different carbon price values by demonstrating that carbon prices are still far too low to motivate managers towards sustainable purchasing choices.

Although distributed additive manufacturing can provide high returns on investment the current markup on commercial filament over base polymers limits deployment. These cost barriers can be surmounted by eliminating the entire process of fusing filament by 3-D printing products directly from polymer granules. Fused granular fabrication (FGF) (or fused particle fabrication (FPF)) is being held back in part by the accessibility of low-cost pelletizers and choppers. An open-source 3-D printable invention disclosed here provides for precise controlled pelletizing of both single thermopolymers as well as composites for 3-D printing. The system is designed, built and tested for its ability to provide high tolerance thermopolymer pellets from a number of sizes capable of being used in a FGF printer. In addition, the chopping pelletizer is tested for its ability to chop multi-materials simultaneously for color mixing and composite fabrication as well as precise fractional measuring back to filament. The US$185 open-source 3-D printable pelletizer chopper system was successfully fabricated and has a 0.5 kg/hr throughput with one motor, and 1.0 kg/hr throughput with two motors using only 0.24 kWh/kg during the chopping process. Pellets were successfully printed directly via FGF and indirectly after being converted into high-tolerance filament in a recyclebot.

The use of commodity polymers such as polypropylene (PP) is key to open new market segments and applications for the additive manufacturing industry. Technologies such as powder-bed fusion (PBF) can process PP powder; however, much is still to learn concerning process parameters for reliable manufacturing. This study focusses in the process-property relationships of PP using laser-based PBF. The research presents an overview of the intrinsic and the extrinsic characteristic of a commercial PP powder as well as fabrication of tensile specimens with varying process parameters to characterize tensile, elongation at break, and porosity properties. The impact of key process parameters, such as power and scanning speed are systematically modified in a controlled design of experiment. The results were compared to the existing body of knowledge; the outcome is to present a process window and optimal process parameters for industrial use of PP. The computer tomography data revealed a highly porous structure inside specimens ranging between 8.46% and 10.08%, with porosity concentrated in the interlayer planes in the build direction. The results of the design of experiment for this commercial material show a narrow window of 0.122 ≥ Ev ≥ 0.138 J/mm³ led to increased mechanical properties while maintaining geometrical stability.

This paper provides an overview of the new CPAM Project on Additive Manufacturing (AM) in design and simulation, focusing on topology & lattice structure optimization for a light-weighting advantage. This industry/academia collaboration project aims to utilize existing hardware and software tools, and investigate the practical limits of the technologies, providing eventual guidelines for general use. This will provide a solid foundation for the practical use of metal AM optimized solid and latticed structures especially for Ti6Al4V parts. Two case studies are demonstrated here, one a purely topology optimized design, and one also incorporating lattice optimized design, both from Ti6Al4V and load-bearing components, to be utilized in the Nelson Mandela University (NMU) Eco-Car Project in competition, late in 2018. This paper presents the Design for Additive Manufacturing (DfAM) process, the challenges met iro applying a DfAM design mindset, and a unique final voxel-based smoothing step finishing off the design process. Detailed structural integrity assessment of these parts are included - the question remains: can Additive Manufacturing help win the race?

Due to the upward trend in the globalization of sustainability issues and the intense competitive environment, it is evident that higher education institutions need new strategic approaches to succeed. To this end, the inquiry for this paper has been made into the debate about student relationship management. Going through the literature indicates that institutions have mainly perceived the concept as a technological initiative for solving the problems in individual domains, accompanied by uncoordinated efforts. Thus, the aims of this study are to theoretically present critical success factors of this strategic approach and to empirically examine the recognized factors. To do so, confirmatory factor analysis that is a quantitative analytic method was performed. The results and analyses revealed that there has been a significant correlation between the four critical success factors including knowledge management, student relationship management technology, student orientation, and employees’ involvement. It was also found that these factors are significantly correlated with the construct of student relationship management success. The findings have consequently highlighted that in addition to the technological tool, the role of knowledge management, employees’ involvement, and student orientation appeared to be particularly important for the implementation of the application.

Biomimicry in additive manufacturing often refers to topology optimization and the use of lattice structures, due to the organic shape of the topology-optimized designs, and the lattices often looking similar to many light-weight structures found in nature such as trabecular bone, wood, sponges, coral, to name a few. Real biomimetic design however involves the use of design principles taken in some way from natural systems. In this work we use a methodology whereby high resolution 3D analysis of a natural material with desirable properties is “reverse-engineered” and the design tested for the purpose. This allows more accurate replication of the desired properties, and adaption of the design parameters to the material used for production (which usually differs from the biological material). One such example is the impact-protective natural design of the glyptodont body armour. In this paper we report on the production of body armour models in metal (Ti4Al4V) and analyze the resulting mechanical properties, assessing their potential for impact protective applications. This is the first biomimetic study using metal additive manufacturing to date.

This paper presents the latest developments in microCT, both globally and locally, for supporting the additive manufacturing industry. There are a number of recently developed capabilities which are especially relevant to the non-destructive quality inspection of additive manufactured parts; and also for advanced process optimization. These new capabilities are all locally available but not yet utilized to their full potential, most likely due to a lack of knowledge of these capabilities. The aim of this paper is therefore to fill this gap and provide an overview of these latest capabilities, showcasing numerous local examples.

In the world industry plant, solid and solid metals are always in contact even their motions not independent. Modeling of rolling die contact with slab primarily needs to describe the Tribology of contact phenomena. Consideration of continuum theory of rolling contact how a contact region is formed between rolling die and slab, and how the tangential force is distributed over the contact area with coefficient of friction is important. The central concern of numerical model is used in this work to indicate a set of equations, derived from the contact principle, that transfer the physical event into the mathematical equations including the laws of nature, such as newton’s laws, boundary conditions, state of stresses and their derivatives at particular time and locations. In this paper the elasticity stress behavior of rolling die contact with slab for number of cyclic loads is modeled. The model is including new proposed constitutive equations for discontinuity of the velocity, pressure distribution in rolling contact from the enter side to exit side of the neutral point. To verify the model, finite element simulation and experimental data from the literature are considered. The results show good agreement with finite element simulation and experimental data.

During the last decades, the production systems have developed different strategies to increase their competitiveness in the global market. In a manufacturing and services systems, Lean Manufacturing has been consolidated through the correct implementation of its tools. The present paper presents a case study developed in a Food Packer company where a Simulation Model was considered as an alternative to reduce the waste time generated by the poor distribution of operations and transportation areas for a product within the factory. As a matter of fact, the company has detected problems on the layout distribution that prevents to fulfill the market demand. In addition, the principal aim was to create a simulation model to test different hypothetical scenarios and alternative designs for the layout distribution without modifying its facilities. Moreover, the implemented methodology was based on classical models of simulation projects and a compendium of the manufacturing systems optimization by simulation process used during the last ten years. Also, a mathematic model supported by the Promodel ® simulation software was developed considering the company characteristics; along with the model development, it was possible to compare the production system performance from the percentage of used locations, the percentage of resources utilization, the number of finished products, and the level of Work in Process (WIP). Finally, the verification and validation stages were performed before running the scenarios in the real production area. The results generated by the implementation of the project represent an increase of 68% in the production capacity and a reduction of 5% in the WIP. In addition, both outcomes are associated with the resources management, which were reassigned to other production areas.

This paper presents a novel method of restoring the electron beam (EB) measurements that are degraded by linear motion blur. This is based on a Fuzzy Inference System (FIS) and Wiener inverse filter, together providing autonomy, reliability, flexibility and real-time execution. This system is capable of restoring highly degraded signals without requiring the exact knowledge of EB probe size. The FIS is formed of three inputs, eight fuzzy rules and one output. The FIS is responsible to monitor the restoration results, grade their validity and choose the one that yields to a better grade. These grades are produced autonomously by analyzing results of Wiener inverse filter. To benchmark the performance of the system, ground truth signals obtained using an 18 um wire probe are compared with the restorations. Main aims are therefore a) Provide unsupervised deblurring for device independent EB measurement; b) Improve the reliability of the process; c) Apply deblurring without knowing the probe size. These, further facilitates the deployment and manufacturing of EB probes and probe independent and accurate EB characterization. It also makes restoration of previously collected EB measurements easier, where the probe sizes are not known or recorded.

Defects are considered one of the wastes in manufacturing systems that negatively affect the delivery times, cost and quality of products leading to manufacturing companies facing a critical situation with the customers and to not comply with the IPC-A-610E standard for the acceptability of electronic components. This is the case is a manufacturing company located in Tijuana, Mexico. Due to an increasing demand on the products manufactured by this company, several defects have been detected in the welding process of electronic boards, as well as in the components named Thru-Holes. It is for this reason that this paper presents a lean manufacturing application case study. The objective of this research is to reduce at least 20% the defects generated during the welding process. In addition, it is intended to increase 20% the capacity of 3 double production lines where electronic boards are processed. As method, the PDCA cycle, is applied. The Pareto charts and the flowchart are used as support tools. As results, defects decreased 65%, 79% and 77% in three analyzed product models. As conclusion, the PDCA cycle, the Pareto charts, and the flowchart are excellent quality tools that help decrease the number of defective components.

This paper focuses on the non-destructive dielectric measurement for low-loss planar materials with a thickness of less than 3 mm using a large coaxial probe with an outer diameter of 48 mm. The aperture probe calibration procedure required only to make a measurement of the half-space air and three offset shorts. The reflection coefficient for the thin material is measured using a Keysight E5071C network analyzer from 0.3 MHz to 650 MHz and then converted to a relative dielectric constant and tangent loss via closed form capacitance model and lift-off calibration process. Measurement error of dielectric constant, Δε_r is less than 2.5 % from 1 MHz to 400 MHz and the resolution of loss tangent, tan δ measurement is capable of achieving 3×10^-3.

In this work a research on pulsed electrochemical micromachining of Stainless Steel is presented. A suitable equipment to study the process is described as well as a fitting procedure to machine and measure the variables involved. A tool of Tungsten with a tip of about 5 mm diameter sunk in an electrolyte of NaNO₃ is used for the process. The pulse on-time must be maintained in the order of ns to achieve a good current confinement, since the tool is active. Some experiments were made to assess the most important variables of the process, as current confinement, surface roughness, material removal rate and efficiency. It is observed that the current confinement get worse when the pulse on-time increases, as well as surface roughness. The material removal rate and the efficiency increase with the voltage amplitude and the pulse on-time. The voltage amplitude must be higher than 12 V so that the phenomenon of passivation disappears. There is a compromise in the choice of the variables, so a suitable combination of parameters is determined so that a good material removal rate with an acceptable result is achieved.

A university canteen is a queueing system characterised by non-stationary time of arrival with limited resources where the arrival rate is time dependent and has different pattern of arrival for different time interval. This means at certain time of the day, the arrival rate is much higher than other time and for a university canteen, the arrival rate of customer during the lunchtime is much higher and the food (resources) is limited. Non-stationary time dependent queueing system is not easily modelled mathematically hence such queueing systems are modelled using simulation tools such as ARENA. In order to model a non-stationary time dependent queueing system with limited resources and solve queueing problems using ARENA, researchers have to depend on their knowledge and experience in identifying the appropriate and relevant parameters for the system and make modifications to these parameters of the system to solve queueing problems by means of trial and error. Hence, this research work explores the potentials of applying a systematic problem solving tool, TRIZ to help users to make better decisions in deriving solutions to improve a non-stationary time dependent queueing system with limited resources. A case study was carried out to minimize the waiting time of the customers at the cafeteria of the Faculty of Engineering, Universiti Putra Malaysia (UPM), which has queueing problems for years during lunchtime. TRIZ was applied in this case study and the results showed that TRIZ can assist researchers to derive a solution model that lead to shorter waiting time without incurring additional cost and resources.

The issues of metallic scrap management and its utilization in manufacturing plants are nowadays intensely considered to address essential sustainability guidelines. Efficient recycling procedure for shop floor metallic scrap is not yet available because of abundance and contamination of nonmetallic constituents. Other ferrous metallic scrap are melted and purified during secondary steelmaking to get products in the form of blooms and billets are obtained. This study illustrates the potential of powder technology (powder metallurgy (PM) and metal injection molding (MIM)) based process for solid-state recycling and attainment of usable products. Industrially downgraded grinding sludge is pulverized and used as a raw material. Results showed properties of sintered parts are significantly improved due to in-situ reduction and densification during sintering. Recyclability Index (RI) was created to compare the effect of process variables on obtained products. Based on RI, recycled ferrous parts have about 70% comparable properties with equivalent pure iron parts. Complex reduction and sintering behavior in MIM, particularly, diffusion and pore volume kinetics limits applicability of MIM with this recycling approach. However, few industrial parts were developed and manufactured by PM based approach to validate the applicability of this novel recycling-cum-manufacturing process for the production of porous parts.

This study investigated the breakdown trend in an automated production with an aim to recommend the application of Reliability-centered maintenance (RCM) for an improved productivity via a new preventive maintenance (PM) program. Individual Section-forming machine (ISM): a glass blowing machine for making glass bottles was used as the case study of an automated production system. The machine parts and the working mechanisms were analysed with a special focus on methods of processes and procedures that will enable the ISM maintenance department run more effective and achieve its essential goal of ensuring effective machine operation and reducing machine downtime. In this work, information is provided on the steps and procedures to identify critical components of the ISM using Failure Modes and Effect Analysis (FMEA) as a tool to develop an optimal maintenance program based on the reliability data of the equipment’s functional components. A relationship was established between the failure rate of the machine components and the maintenance costs such that using the recommended PM program, an evidence of improvement in the machine’s availability, safety and cost-effectiveness will result into an increase in the company’s profit margin.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

This work explores an additive-manufacturing-enabled combination-of-function approach for design of modular products. AM technologies allow the design and manufacturing of nearly free-form geometry, which can be used to create more complex, multi-function or multi-feature parts. The approach presented here replaces sub-assemblies within a modular product or system with more complex single parts that are designed and manufactured using AM technologies. This approach can increase the reliability of systems and products by reducing the number of interfaces, as well as allowing the optimization of the more complex parts during the design. The smaller part count and the ability of users to replace or upgrade the system or product parts on-demand should reduce user risk, life-cycle costs, and prevent obsolescence for the user of many systems. This study presents a detailed review on the current state-of-the-art in modular product design in order to demonstrate the place, need and usefulness of this AM-enabled method for systems and products that could benefit from it. A detailed case study is developed and presented to demonstrate the concepts.

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

Remanufacturing is a viable option to extend the useful life of an end-of-use product or its parts, ensuring sustainable competitive advantages under the current global economic climate. Challenges typical to remanufacturing still persist, despite its many benefits. According to the European Remanufacturing Network a key challenge is lack of accurate, timely and consistent product knowledge as highlighted in a 2015 survey of 188 European remanufacturers. With more data being produced by electric and hybrid vehicles, this adds to the information complexity challenge already experienced in remanufacturing. Therefore, it is difficult to implement real-time and accurate remanufacturing for the shop floor; there are no papers that focus on this within an electric and hybrid vehicle environment. To address this problem this paper attempts to (1) identify the required parameters/ variables needed for fuel cell remanufacturing by means of interviews (2) rank the variables by Pareto analysis (3) develop a casual loop diagram for the identified parameters/ variables to visualise its impact on remanufacturing (4) model a simple stock and flow diagram to simulate and understand data and information-driven schemes in remanufacturing.

This paper reports on the production and mechanical properties of Ti6Al4V micro-lattice structures, with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the mechanical properties and manufacturability of such thin-strut lattices, this paper also reports on the in-situ deformation imaging of micro-lattice structures with 6 unit cells in every direction. LPBF lattices are of interest for medical implants, due to the possibility of creating structures with an elastic modulus close to that of the bones and small pore sizes which allow effective osseointegration. In this work four different cubes were produced by laser powder bed fusion and subsequently analyzed using microCT, compression testing and one selected lattice was subjected to in-situ microCT imaging during compression. The in-situ imaging was performed at 4 steps during yielding. The results indicate that mechanical performance (elastic modulus and strength) correlate well with actual density and that this performance is remarkably good, despite the high roughness and irregularity of the struts at this scale. In-situ yielding is visually illustrated.

The article presents a cyber-physical system for acquiring, processing and reconstructing images from measurement data. The technology was based on process tomography, intelligent measurement sensors, machine learning, Big Data, Cloud Computing, Internet of Things as a solution for Industry 4.0. Industrial tomography enables observation of physical and chemical phenomena without the need of internal penetration and allows real-time monitoring of production processes. The application includes specialized intelligent devices for tomographic measurements and dedicated algorithms for solving the inverse problem. The work focuses mainly on electrical tomography and image reconstruction using deterministic methods and machine learning, the reconstruction results were compared, different measurement models were used. The researches were carried out for synthetic data and laboratory measurements. The main advantage of the proposed system is the possibility of spatial data analysis and their high processing speed. The presented research results show that the process tomography gives the possibility to analyse the processes taking place inside the facility without disturbing the production, analysis and detection of obstacles, defects and various anomalies. Knowing the characteristics of a given solution, the application allows you to choose the appropriate method to reconstruct the image.

This research aimed, within the scope of the anthropotechnological approach, analyze the technology transfer, performed via the offset policy in the field of public health, called the Radiotherapy Expansion Plan, from the Health Ministry. The objective of this policy is to create and improve accredited organizations, concerning the oncological treatment, specifically in the insertion of radiotherapeutic equipment. This process is divided into two stages: the insertion of the radiotherapy equipment, and the compensations provided for in the commercial agreement. To meet this purpose, the research started from understanding the theoretical and methodological approaches of the fields of study of anthropotechnology, technology transfer and offset policy. In this sense, there was used the methodological strategy of the case study, supported by applied research, with a qualitative and exploratory approach. External and internal environments of a specific situation were analyzed, located in the State of Paraná, which received the radiotherapy equipment. It was verified that the initiatives of insertion of radiotherapeutic equipment in the context of the Expansion Plan have undergone numerous confrontations, inserted in the contextual and organizational particularities that affect its development and effectiveness. There are challenges that require responses from a set of organizations involved, in order to implement the trade agreement established by the offset policy, highlighting the first stage as a process of technology transfer. Thus, the situation located in the State of Paraná consistently consolidated the insertion of the radiotherapy equipment. It allowed its disclosure as a reference situation, and based on the dimensions and indicators analysis provided by anthropotechnology, made possible the comprehensionof the technology transfer involved in the process.

Transient liquid phase (TLP) bonding of Al-6063 and UNS S32304 was performed using copper foil as an interlayer between the base metals. A compression load was applied normal to the specimens. Metallurgical examination of the produced joints showed three distinct regions including a reaction zone, diffusion affected zone and the base metals. The diffusion of copper into aluminum resulted in an Al-Cu eutectic structure. However, the oxide layer on the aluminum surface controlled the dissolution behavior of copper and the extent of its wettability with the base metals. Although voids and intermetallic compounds were detected at the interfaces of the processed joints, a defect free joint was produced at 570°C. In addition, the results from corrosion tests showed that the use of copper as an interlayer decreased the corrosion resistance of the joints. However, increase in thickness of the joining reaction zone with increasing bonding temperature was observed to increase corrosion resistance.

Technology development changes society and society demands new and innovative technology development. We analyze technology to understand society and technology itself. Many researches have been introduced in various fields. Most of them were about patent analysis. This is because detailed and accurate results of research and development are patented. In this paper, we study on new patent analysis method based on count data model and Bayesian regression analysis. Using count data model, we analyze the technological keywords extracted from the collected patent documents. We use the posterior distribution of Bayesian statistics to reflect the experience and knowledge of the relevant technological experts in the analysis model. Moreover, we apply the proposed model to finding sustainable technologies. Finding and developing sustainable technologies is an important activity for companies and research institutes to maintain their technological competitiveness. To illustrate how our modeling could be applied to real domain, we carry out a case study using the patent documents related to artificial intelligence.

The Circular Economy has been of growing significance within academic, policymaking and industry groups. Latest developments in the field of Circular Economy has led to an expansion of CE studies focused on interrogating CE as a paradigm, its relationship with sustainability and concepts and definitions of the Circular Economy. Research has also identified the significant potential of applying circular approaches to areas of the economy, including manufacturing and Industry 4.0, which, with data, is enabling latest the advances in digital technologies. This is the first review paper to integrate the fields of CE and digital technologies resulting in a framework which provides directions for policymakers and guidance for future research. To achieve this, we conduct a systematic literature review of the empirical literature related to digital technologies, industry 4.0 and circular approaches, from the point of the 9 Rs. The systematic literature review (SLR) is based on peer-reviewed articles published between 2000-2018. The findings reveal that while research on the circular economy has been on an annual rise, research on digital technologies enabled circular economy is still relatively an untouched area of research across all nine (9) circular approaches. As such this is an area rife for further research. This paper also presents illustrative charts and graphs to summarize the current trends in circular economy research in manufacturing. From this, a framework for future circular economy research for manufacturing for digital technologies is proposed.

The differential gear train and speed regulating motor constitute the variable ratio transmission for grid-connected wind turbine with differential speed regulation. The synchronous generator in the system can accessing the power grid without frequency converter. The transmission can realize the mode of variable speed constant frequency that the wind rotor speed is varying and the generator rotor speed is constant. The power control method is studied under the different wind speed which is lower or higher than rated wind speed with using the relational expression of utilization rate of wind energy Cp, pitch angle β and the tip speed ratio λ. The SIMULINK software is used to build the 1500 kW wind turbine model with differential speed regulation. Some different wind speed is made as input. The feasibility of power control method for grid-connected wind turbine with differential speed regulation is verified by the comparison between the simulation results and the theoretical value of the key parameters.

Abstract: Unusual methane emission and spontaneous combustion of coal induced by the air leakage are both hazards during mining. The most common practice has been to improve mine safety is sealing the mining fractures. In this paper, the methane and geology, coal spontaneous combustion characteristics and the coexistence of methane emission and spontaneous combustion of coal were analyzed. The preparation system of inorganic solidified foam (ISF) in field applications is studied and the working principle of generating device consists of foam generator and mixer was expounded. The technical plan of site construction is that the foam fluids was injected to respectively seal the mining fractures behind hydraulic supports, the cavities of air return corner, and the fractures nearby the coal pillar. After the foam fluids injection, the two stress values in the coal pillar eventually maintained above 15.5Mpa and 13Mpa, respectively. It indicated that the ISF can enhance the bearing stress ability of the coal pillar by transforming the stress state from two dimensional to three dimensional. The methane concentration in the air return corner and air return roadway declined significantly to 0.63% and 0.25%. The differential pressure inside and outside of the 4301(1) goaf fluctuated between -100pa to 150pa and the concentration of CO and O2 declined to 9ppm and 6%. The CO concentration in the air return corner finally reached a stable level of 6ppm. What that all means, the foam fluids can seal the air leakage and inhibit spontaneous combustion of coal effectively.

Computational fluid dynamics (CFD) has, in the last decade, being an essential problem solving tool in industries such as pharmaceutical, pulp, petrochemical as well as Oil and Gas processing. The use of CFD for mixer design is unpopular in many countries in Africa. Therefore, this study investigates the characteristics of Brine-Surfactant mixing in a horizontal pipeline using CFD. The CFD is conducted by AnsysFluent software (licensed). A T-junction pipe is created and meshed with unstructured tetrahedral elements using design modeler. Discretization is done by Finite Volume Method (FVM), cell-centered scheme with Second-Order Upwind Scheme. The pressure term is introduced into the continuity equation by SIMPLE (Semi-Implicit Method for Pressure Linked Equations) algorithm. The kinetic epsilon model, also known as k-e model is administered to define the properties of the fluid and geometry, such as velocity, species mole fraction, pipe diameter. The boundary conditions is selected based on filed data. The rate of fluid flow in the primary region is 650 bbl/day at 400psi in 4in diameter pipeline, which is 100m long. The numerical simulation was based upon the governing equations such s continuity, Navier’s stoke, energy as well as specie transport equations. The findings shows that higher concentration results in increased mixing time, while 2% conc. of surfactant reaches homogeneity in 20 minutes at 72 meters of the pipe length. The result validated with field detail and the empirical result from literature, and is consistent. This study provide insight on industrial mixer design, chemical injection system, as well as gas pipeline design and optimization, especially in multiphase scale transport.

In the manufacturing industry, cutting tool failure is a probable fault which causes damage to the cutting tools, workpiece quality and unscheduled downtime. It is very important to develop a reliable and inexpensive intelligent tool wear monitoring system for use in cutting processes. A successful monitoring system can effectively maintain machine tools, cutting tool and workpiece. In the present study, the tool condition monitoring system has been developed for Die steel (H13) milling process. Effective design of experiment and robust data acquisition system ensured the machining forces impact in the milling operation. Also, ANFIS based model has been developed based on cutting force-tool wear relationship in this research which has been implemented in the tool wear monitoring system. Prediction model shows that the developed system is accurate enough to perform an online tool wear monitoring system in the milling process.

The aim of this paper is to explore the watertightness behaviour for high pressure applications using Multijetfusion technology and polyamide 12 as a material. It reports an efficient solution for manufacturing functional prototypes and final parts for water pressure applications. It provides manufacturing rules to engineers in the pressurized product development process up to 10 MPa of nominal pressure. The research findings show manufacturers the possibility of using additive manufacturing as an alternative to traditional manufacturing. Water leakage was studied using different printing orientations and wall thickness for a range of pressure values. An industrial ball valve was printed and validated with the ISO 9393 standard also meeting tolerance requirements. This paper is a pioneering approach to the additive manufacturing of high performance fluid handling components. This approach solves the problem of leakage caused by porosity in additive manufacturing technologies

Manufacturing of grinding wheels is continuously adapting to new industrial requirements. New abrasives and new wheel configurations, together with wheel wear control allow for grinding process optimization. However, the wear behavior of the new abrasive materials is not usually studied from a scientific point of view due to the difficulty to control and monitor all the variables affecting the tribochemical wear mechanisms. In this work an original design of pin on disk tribometer is developed in a CNC grinding machine. An Alumina grinding wheel with special characteristics is employed and two types of abrasive are compared: White Fused Alumina (WFA) and Sol-Gel Alumina (SG). The implemented tribometer reaches sliding speeds of between 20 and 30 m/s and real contact pressures up to 190 MPa. The results show that the wear behavior of the abrasive grains is strongly influenced by their crystallographic structure and the tribometer appears to be a very good tool for characterizing the wear mechanisms of grinding wheels, depending on the abrasive grains.

The use of the LMD technology as a manufacturing and repairing technique in industrial sectors like the die and mold and aerospace is increasing within the last decades. Research carried out in the field of LMD process situates argon as the most usual inert gas, followed by nitrogen. Some leading companies have started to use helium and argon as carrier and shielding gas, respectively. There is therefore a pressing need to know how the use of different gases may affect the LMD process due to there is a lack of knowledge with regard to gas mixtures. The aim of the present work is to evaluate the influence of a mixture of argon and helium on the LMD process by analyzing single tracks of deposited material. For this purpose, special attention is paid to the melt pool temperature, as well as to the characterization of the deposited clads. The increment of helium concentration in the gases of the LMD processes based on argon will have three effects. The first one is a slightly reduction of the height of the clads. Second, an increase of the temperature of the melt pool. Last, smaller wet angles are obtained for higher helium concentrations.

Stem cells derived from dental tissues—dental stem cells—are flavored due to their easy acquisition. Among them, dental pulp stem cells (DPSCs) extracted from the dental pulp have many advantages such as high proliferation and highly purified population. Although their ability for neurogenic differentiation has been highlighted and neurogenic differentiation using electrospun nanofibers (NFs) has been performed, graphene-incorporated NFs have never been applied for DPSC neurogenic differentiation. Here reduced graphene oxide (RGO)-polycaprolactone (PCL) hybrid electrospun NFs were developed and applied for enhanced neurogenesis of DPSCs. First, RGO-PCL NFs were fabricated by electrospinning with incorporation of RGO and alignments, and their chemical and morphological characteristics were evaluated. Furthermore, in vitro NF properties such as influence on the cellular alignments and cell viability of DPSCs were also analyzed. The influences of NFs on DPSCs neurogenesis was also analyzed. The results confirmed that an appropriate concentration of RGO promoted better DPSC neurogenesis. Furthermore, the use of random NFs facilitated contiguous junctions of differentiated cells, whereas the use of aligned NFs facilitated aligned junction of differentiated cells along the direction of NF alignments. Our findings showed that RGO-PCL NFs can be a useful tool for DPSC neurogenesis, which will help regeneration in neurodegenerative and neurodefective diseases.

The present work proposes a novel manufacturing technique based on the combination of Laser Metal Deposition, Laser Beam Machining and Laser Polishing processes for the complete manufacturing of complex parts. Therefore, the complete process is based on the application of a laser heat source both for the building of the preform shape of the part by additive manufacturing and for the finishing operations. Their combination enables to manufacture near-net-shape parts and afterwards, remove the excess material via laser machining, which has resulted to be capable of eliminating the waviness resulting from the additive process. Besides, surface quality is improved via laser polishing to reduce the roughness of the final part. Therefore, conventional machining operations are eliminated, what results in a much cleaner process. In order to validate the capability of this new approach, the dimensional accuracy and surface quality of the resulting parts are evaluated. The process has been validated on an Inconel 718 test part, where a previously additively built up part has been finished by means of laser machining and laser polishing.

A numerical model was developed for predicting the bead geometry and microstructure in Laser Beam Welding of 2 mm thickness Inconel 718 sheets. The experiments were carried out with a 1 kW maximum power fiber laser coupled with a galvanometric scanner. Wobble strategy was employed for sweeping 1 mm wide circular areas for creating the weld seams and a specific tooling was manufactured for supplying protective Argon gas during the welding process. The numerical model takes into account both the laser beam absorption and the melt-pool fluid movement along the bead section, resulting in a weld geometry that depends on the process input parameters, such as feed rate and laser power. The microstructure of the beads was also estimated based on the cooling rate of the material. Features as bead upper and bottom final shapes, weld penetration and dendritic arm spacing were numerically and experimentally analyzed and discussed. The results given by the numerical analysis agree with the tests, making the model a robust predictive tool.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

During the recent decades, global warming by greenhouse gas evolution has attracted worldwide attention and evermore strict regulations thereon have become institutionalized as international policies. In the process, more environment-friendly power generation technologies have been developed utilizing fossil fuels with a view to timely commercialization. As one of such “clean coal” technology, Integrated Gasification Fuel Cell system is a promising power generation means and COS hydrolysis reactor is installed downstream of coal syngas to remove acidic gas constituents such as H2S and COS. The most significant design parameters affecting performance of the COS hydrolysis reactor were selected to be GHSV, (catalytic) reaction temperature, and length ratio and numerical modeling was performed considering heat and fluid flow transfer as well as chemical reaction kinetics. Effect of the selected design parameters on the variation of conversion rate and reactant gas mixture concentration were comprehensively investigated to predict performance of COS hydrolysis reactor. Stochastic modeling of reactor performance was finally performed using Monte Carlo simulation and linear regression fitting.

Interviews from strength and conditioning coaches across all levels of athletic competition identified their two biggest concerns with the current state of wearable technology: (a) the lack of solutions that accurately capture data "from the ground up" and (b) the lack of trust due to inconsistent measurements. The purpose of this research is to investigate the use of liquid metal sensors, specifically Liquid Wire sensors, as a potential solution for accurately capturing ankle complex movements such as plantar flexion, dorsiflexion, inversion, and eversion. Sensor stretch linearity was validated using a Micro-Ohm Meter and a Wheatstone bridge circuit. Sensors made from different substrates were also tested and discovered to be linear at multiple temperatures. An ankle complex model and computing unit for measuring resistance values were developed to determine sensor output based on simulated plantar flexion movement. The sensors were found to have a significant relationship between the positional change and the resistance values for plantar flexion movement. The results of the study ultimately confirm the researchers' hypothesis that liquid metal sensors, and Liquid Wire sensors specifically, can serve as a mitigating substitute for inertial measurement unit (IMU) based solutions that attempt to capture specific joint angles and movements.

To enhance industrial competitiveness and increase productivity, every country has strived to create a smart factory by introducing technologies such as Internet of Things, big data and artificial intelligence into production line and build cyber-physical system for the purpose of promoting manufacturing efficiency. For mission assignment, production line management or manufacturing field analysis, the location information of employee, machine and material is very essential. To promote manufacturing efficiency, of course, the location information became more important. A Bluetooth low energy (BLE) positioning system for the manufacturing is developed in this research. A "Tag tracking" mechanism is addressed and adopted, which uses Beacon to catch the location information and a BLE receiver is also used to receive the broadcasting information from Beacon. The position information from the BLE receiver will be compared with the data in the database for calculating the location of the target. The status of the target may also be obtained by using the data from the BLE receiver. Comparing with the mobile device, this method can reduce energy consumption and make the maintenance simple and easy. In the real applications, the target may not be limited to human. The "Regional label positioning technology" is also investigated in this research. Defining a suitable zone location and arranging BLE receiver location, and positioning analysis theory are the key factors included in this developed technology. The developed system will be tested for real industry applications. The test results show that the feasibility of this technology.

A via ferrata (from the German “klettersteig”, hereinafter VF) is a sports route located on forest and mountains vertical rock walls equipped with steps, chains, artificial dams, bridges and other fixed elements and which have a steel cable (safety cable) all the way along allowing users to secure their progress and avoid possible falls [1]. This article aims to analyse the state of the art of the VF sector in Spain, especially in terms of the regulations of obligatory compliance, in addition to defining the basic characteristics of the installations to ensure that these are safe for users, providing a previously non-existent summary of the most important recommendations regardless of the country where they are installed.

In this article, a novel hybrid welding process called plasma-TIG coupled arc welding was proposed to improve the efficiency and quality of welding by utilizing the full advantage of plasma and TIG welding processes. The two arcs of plasma and TIG were pulled into each other into one coupled arc under the effect of Lorentz force and plasma flow force during welding experiments. The arc behavior of coupled arc was studied by means of it’s arc profile, arc pressure and arc force conditions. The coupled arc pressure distribution measurements were performed. The effects of welding conditions on coupled arc pressure were evaluated and the maximum coupled arc pressure was improved compared with single-plasma arc and single-TIG arc. It was found that the maximum arc pressure was mainly determined by plasma arc current and plasma gas flow. According to the results, the proposed coupled arc welding process have both advantages of plasma arc and TIG method, and it has a broad application prospect.

Hot rolling tests of a low-alloy steel were conducted at a rolling temperature of 850 ℃ under different lubrication conditions, including benchmarks (dry condition and water) and water-based nanolubricants containing different concentrations of nano-TiO₂ from 1.0 to 8.0 wt%. The effects of nanolubricants on rolling force, surface roughness, thickness of oxide scale and microstructure were systematically investigated through varying nano-TiO₂ concentrations. The results show that the application of nanolubricants can decrease the rolling force, surface roughness and oxide scale thickness of rolled steels, and refine ferrite grains. In particular, the nanolubricant containing an optimal concentration (4.0 wt%) of nano-TiO₂ demonstrates the best lubrication performance, owing to the synergistic effect of lubricating film, rolling, polishing and mending generated by nano-TiO₂.