Wind energy is becoming an essential source of power for countries which have the aim to reduce greenhouse gases emission and mitigate the effects of global warming. The Wind Turbines (WTs) installed around the globe is increasing significantly every year. The dramatic increase in wind power has encountered quite a few challenges, among which the major issues are availability and reliability. The unexpected failure in WTs Gearbox (GB) ultimately increases the Operation and Maintenance (O&M) cost. The identification of faults in the earlier stages before it turns to catastrophic damage to other components of WT is crucial. This research deals with the prediction of WT failures by using a Supervisory Control and Data Acquisition (SCADA) system. The main aim is to forecast the temperature of the WTs GB to predict the impending overheating of the GB at an early stage. The earlier prediction will help to optimize the maintenance period and to save maintenance expenses and, even more important, generate warnings in due time to avoid major damages or even technical disasters. In the proposed method we compared six different machine learning (ML) models based on error and accuracy of prediction. The bagging regressor is the best ML model, which results in the mean square error of 0.33 and R of 99.8 on training data. The bagging regressor is then used to predict the fault in the WT GB, which detected the anomalous behavior of WT GB 59 days earlier than the actual failure. This model also detects the extremely unusual behavior of the GB 9 days earlier than a complete failure.

Abstract: — management of the Continuous Stirred Tank Reactor (CSTR) operation has proven to be a difficult undertaking due to the complex and ever-changing nature of its behavior, which is both nonlinear and dynamic, which is further compounded by its instability. Attempts have been made to use Proportional-Integral-Derivative (PID) controllers for such processes, but the performance is often poor due to the inherent limitations of the controllers. In contrast, heuristic algorithms have been employed to tune the controllers, but these methods can only provide optimal performance for a restricted range of parameter variations. This paper presents a novel approach that involves using a conventional gain scheduling PID controller in combination with a fuzzy gain scheduling (FGS) controller method to calibrate set-point weighted PID controllers for the CSTR process. The paper outlines the design of the controllers and evaluates their performance by subjecting them to varying input signals within the given bandwidth.

In this work, a highly efficient, molybdenum disulfide (MoS2) based near infrared (NIR) heterojunction photodetector is fabricated on a Si substrate using a cost-effective and simple drop casting method. A non-stoichiometric and inhomogeneous MoS2 layer with a S/Mo ratio of 2.02 is detected using energy dispersive X-ray spectroscopy and field emission scanning electron microscope analysis. Raman shifts are noticed at 382.42 cm-1 and 407.97 cm-1, validating MoS2 thin film growth with a direct bandgap of 2.01 eV. The fabricated n-MoS2/p-Si photodetector is illuminated with a 785 nm laser at different intensities, and demonstrate the ability of the photodetector to work in both regions, the forward biased and reverse biased from above 1.5 V and less than -1.0 V. The highest responsivity, R is calculated to be 0.52 A/W while the detectivity D* is 4.08 x 10^10 Jones for an incident light intensity of 9.57 mW/cm2. The minimum rise and fall times are calculated as 1.77 ms and 1.31 ms for an incident laser power of 9.57 mW/cm^2 and 6.99 mW/cm^2 respectively at a direct current bias voltage of 10 V. The demonstrated results are promising for the low-cost fabrication of a thin MoS2 film for photonics and optoelectronic device applications.

This paper describes the indoor air pollution in urban (Lahore, Faisalabad, Gujranwala, Rawalpindi and Karachi) Pakistani regions while considering the outdoor air and the health and wellbeing of the occupants present indoors. It also aims to assess previous methodological approaches Such as Air Conditioning Systems, used by developed countries to improve air quality to demonstrate the improvements that can be made in air quality in Pakistani urban areas. This research also investigates the causes, concentration and effects of poor air quality in Pakistani urban areas such as particulate matter (PM2.5), carbon oxides (COx), nitrogen oxides (NOx), sulphur oxides (SOx) and volatile organic compounds (VOC’s). The average concentration of these pollutants in Pakistan’s indoor air is, particulate matter (PM): [100 – 250 µg/m3 for PM2.5, 200 – 600 µg/m3 for PM10] 1 – 20 ppm for carbon monoxide (CO), nitrogen oxides (NOx): [50 – 100 µg/m3 for NO2, 20 – 40 µg/m3 for NO], 20 – 50 µg/m3 for sulfur dioxide (SO2), volatile organic compounds (VOCs): 0.1 – 0.5 ppm for formaldehyde, 5 – 10 µg/m3 for benzene and 20 – 30 µg/m3 for toluene. It should be noted that these concentrations can differ depending on the origin of pollution, location, and time of day. The literature review is made up of a combination of descriptive research methods that are used to inform the research background of ambient and indoor air quality, thus the literature review provides a theoretical and methodological background about the air pollution and its improvement in different parts of the world. According to the World Air Quality Index, Pakistan is the third most polluted country in terms of average PM2.5 concentration which is 14.2 times the WHO annual air quality guideline value. As a result, it is suggested that a PM2.5 concentration reduction program be implemented in urban Pakistani regions' indoor air.

Bitumen is produced from non-renewable natural resources, continuously deplete and intrigues researchers to look for alternative binders. Annually, tons of waste engine oil (WEO) and crumb rubber (CR) are discarded unsustainably and pose a significant environmental threat. Adding these industrial waste products to asphalt provides a safe and cost-effective way for their disposal and improves the bitumen's performance in parallel. This study uses various combinations of waste engine oil and crumb rubber with 60/70 penetration grade bitumen to produce a partially synthetic bitumen. Adhesion being one of the critical characteristics of the bituminous binder has been assessed using the bitumen bond strength test along with physical and rheological properties. Results showed that waste engine oil with crumb rubber inclusion increases penetration and decreases the softening point, viscosity, complex modulus, and bonding strength. Additionally, polyphosphoric acid (PPA) in smaller dosages was also incorporated into the optimum percentage of CR + WEO to improve the properties of the binder. The results confirm that binder modification with waste engine oil and crumb rubber can be more effective with PPA. It is concluded that 35% of waste can replace the virgin binder giving a cost-effective and environmentally friendly solution.

Rhenium Disulfide (ReS2) has evolved as a novel 2D transition-metal dichalcogenide (TMD) material which has promising applications in optoelectronics and photonics because of its distinctive anisotropic attributes. In this review, we emphasize on formulating saturable absorbers (SAs) based on ReS2 to produce Q-switched and mode-locked pulsed lasers of diverse operation wavelengths like 1 μm, 1.5 μm, 2 μm, and 3 μm. We outline ReS2 synthesis techniques and integration platforms concerning solid-state and fiber-type lasers. We discuss the laser performance based on SAs attributes. Lastly, we draw conclusions and outlook by recommending additional improvements for SA devices so as to advance the domain of ultrafast photonic technology.

Organophilic nano clay is the composition of mostly clay and organic molecules designed to improve various materials' physical and chemical properties. Permanent deformation in asphalt pavements is primarily the result of inadequate compaction, excessive loading, and high temperatures. Rutting can result in aquaplaning, leading to accidents and costly maintenance and rehabilitation works that drain the economy. Such behavior of asphalt pavements may be attributable to poor selection of aggregate, asphalt binder, or substandard asphalt binders. This study used different percentages of organophilic nano clay ranging from 3.0% - 5.0% with two penetration grade bitumen, i.e., N.R.L 60-70 & N.R.L 80-100. Adding organophilic nano clay to asphalt binder significantly reduced the rutting potential under cyclic loading at high temperatures (55 °C). Ten modified formulations and two virgin bitumen specimens were prepared. The modified binders' viscosity and rutting were tested using the Rotational Viscometer and Wheel Tracker Test (W.T.T.), respectively. The results were analyzed using software for Statistical Analysis. It was recorded that organophilic nano clay-modified bitumen significantly affected rutting to interpret the results. The results indicated that rutting decreased and viscosity increased in all nano clay-modified bitumen samples, with a 4.5% O.N.C modified binder showing the most significant improvement.

The reconstructive ladder is a well-established concept in Plastic Surgery proposed to achieve wound closure using a stepladder approach from simple to complex procedures and it continues to evolve from when it was presented for the first time. We describe a new surgical technique that allows skin excision and primary wound closure avoiding donor site morbidity from skin grafts and avoiding large scars from loco-regional flaps: the parallelogram excision technique. Fifteen patients with skin lesions underwent this procedure. Six months' follow-up results showed a) good scar healing, b) total excision of lesions, and c) patient acceptance and satisfaction from the usage of this technique. We conducted a geometrical analysis of the parallelogram’s design to study the optimal geometrical condition to achieve all these three factors. We propose that the parallelogram excision of skin lesions proves to be a unique new wound closure technique that may add a new rung to the reconstructive ladder.

The global increase in population, the phenomenon of climate change, the issue of water pollution and contamination, and the inadequate management of water resources all exert heightened strain on freshwater reserves. The potential utilization of the interfacial solar steam generation (ISSG) system, which utilizes photothermal conversion to generate heat on material surfaces for wastewater purification and desalination purposes, has been successfully demonstrated. Textile materials based ISSG devices, including (woven, nonwoven and knitting) fabrics and electrospinning membranes, exhibit distinct properties such as rough surface texture, high porosity, significant surface area, exceptional flexibility, and robust mechanical strength. These characteristics, combined with their affordability, accessibility, and economic viability for widespread implementation, make them extremely attractive for applications in SSG. In this review, a comprehensive analysis of emerging concepts, advancements and applications of textile materials (woven, nonwoven, and knitting) fabrics and electro-spun membranes in the ISSG for wastewater purification and desalination is highlighted. We also emphasize significant obstacles and potential prospects in both theoretical investigations and real-world implementations, aiming to contribute to future advancements in the domain of textile based materials interfacial evaporation in wastewater purification and desalination. Furthermore, the drawbacks and the challenges of ISSG systems are also highlighted.

Convolutional neural network architectures have become increasingly complex, which has improved the performance slowly on well-known benchmark datasets in the recent years. In this research, we have analyzed the true need for such complexity. We have introduced G-Net light, a lightweight modified GoogleNet with improved filter count per layer to reduce feature overlaps and complexity. Additionally, by limiting the amount of pooling layers in the proposed architecture, we have exploited the skip connections to minimize the spatial information loss. The investigations on the proposed architecture are evaluated on three retinal vessel segmentation publicly available datasets. The proposed G-Net light outperforms other vessel segmentation architectures by reducing the number of trainable parameters..

As urban populations and transport demand expand, Pakistani metropolitan centers face traffic congestion and environmental challenges. This research aims to assess carpooling (CP) to alleviate traffic congestion, fuel demand, and pollution. This study was conducted in Islamabad, a fast-growing city with a high percentage of personal cars in Pakistan, to assess the travelers’ perceptions, and public acceptance of CP and determine the effects on traffic congestion, fuel consumption, and CO2 emissions. The investigation of travelers' perceptions towards CP was conducted through a stated preference questionnaire survey. A total of 700 responses from one million population of Islamabad were collected as per Sloven's Formula. SPSS and Smart PLS software were used for data analysis. Various factors influencing peoples’ travel perceptions, mode choice, and tendency to carpool, were categorized to evaluate the relationship between travelers’ perception and the tendency to carpool in the presence of mode choice as a mediating variable. Confirmatory factor analysis was conducted in SMART PLS to refine the number of scale items for each variable. One-way ANOVA, step-wise and mediated multiple regression analysis was conducted in SPSS to check the direct and mediating relationship between different variables. Moreover, the probability of reducing traffic congestion and assessing fuel reduction resulting from CP was also analyzed. The findings imply that travelers’ mode choice acts as a mediator between the relationship between travelers’ perception and tendency to carpool. Furthermore, results predicted that CP might reduce 0.25 million cars on the road, about 33.6% of the total private vehicles. Thereby, saving up to 546,810 barrels per year, about 3.42% of Pakistan's total petrol consumption. The findings of this study could be helpful for transport planners, environmentalists, and policymakers to implement carpool systems. Thus, reducing traffic congestion and harmful CO2 emissions and maintaining a sustainable environment.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

Voltage Source Inverters (VSI) are the integral part of Electrical Vehicles (EV) to enhance the reliability of supply power to critical loads in vehicle to load (V2L) applications. Inherent properties of sliding mode control (SMC) makes it one of the best vailable options to achieve desired voltage quality under variable load conditions. Intrinsic characteristic of robustness associated with SMC is achieved generally at the cost of unwanted chattering along the sliding surface. To manage this compromise better, optimal selection of sliding surface coefficient is applied with proposed composite exponential reaching law (C-ERL). The novelty of proposed C-ERL is associated with the intelligent mix of exponential, power and difference functions blended with rotating sliding surface selection (RSS) technique for three phase two level VSI. Moreover, proposed reaching law along with power rate exponential reaching law(PRERL), enhanced exponential reaching law(EERL) and repeatitive reaching law(RRL) are implemented on two level three phase VSI under variable load condtions. Comparative analysis of which strongly advocates the authenticity and effectiveness of proposed reaching law in achieving well regulated output voltage, with high level of robustness, reduced chattering and low %THD.

Gwadar is essential for Pakistan's financial stability. The third deep-water port in Pakistan, Gwadar, plays a significant part in trade between the Gulf countries, Africa, China, United Arab Emirates, and Cordillera Administrative Region. However, the load Shedding of 12-16 hours in Gwadar is the most concerning issue. Pakistan imports 70 MW of electricity from Iran. The wind and solar system are already installed but for a limited residential area. In Gwadar, there are enough renewable energy resources that can be utilized for electricity generation. In this context, a Techno and Economic Analysis is performed using the Hybrid Optimization Model for Multiple Energy Resources (HOMER) Pro. Two models are considered for this study. Model-1 includes PV/Wind Turbine/ and Battery while Model-2 consists of PV/Wind Turbine/Converter and Grid. The yearly energy generated by Model-1 and Model-2 is 57.37 GWh and 81.5 GWh, respectively. The levelized cost of electricity (LCOE) for Model-1 and Model-2 is respectively $0.401/kWh and $0.0347/kWh. It is shown that the simple payback of Model-1 is of 6.70 years, and the simple payback of Model-2 is 7.77 years. Due to the high LCOE of Model-1, its payback year is lesser than model-2. All of these facts indicate that Model 2 is the most optimal solution.

Background: Alzheimer’s disease (AD), the most threatening neurodegenerative diseases, is characterized by the loss of memory and language function, an unbalanced perception of space and other cognitive and physical manifestations. Pathology of the AD is characterized by neuronal loss, and the extensive distribution of senile plaques and neurofibrillary tangles (NFTs). The role of environment and the diet in the AD is being studied actively, and nutrition is certainly one of the main factors playing a prominent role in the prevention of neurodegenerative diseases. In this context, the relationship between dementia and wine use/abuse has received increased research interest in recent times, with varying and often conflicting results. Scope and approach: This review aims to critically summarize the most recent studies conducted to clarify the relationship between wine drinking and AD, as well as whether effects are influenced by quantity and/or frequency of drinking. Key findings and Conclusion: Overall, based on the interpretation of various studies, it can be concluded that there is no indication that light to moderate alcohol drinking is detrimental to cognition and dementia, and it is not possible to define whether alcohol could be used as a means to reduce risk of developing AD.

In everyday life, the birth of a number of blind people takes place and millions of people are already available. Visually impaired people struggle to walk safely and in- dependently because they have trouble detecting obstacles. In this work, we suggest a novel approach to detecting obstacles utilizing an Arduino UNO board and an ul- trasonic sensor (HC-SR04). The main goal of this research is to increase the mobility and security of blind people in a variety of settings. The suggested system makes use of the HC-SR04 ultrasonic sensor’s capability to precisely measure distance and identify nearby obstructions. As the main processor component, the Arduino UNO board processes algorithms for real-time obstacle detection while also collecting data from the sensor. The device is intended to give the visually impaired user immedi- ate aural input while informing them of the location and proximity of obstacles. To Extensive testing is done in controlled and real-world settings to assess the system’s performance and dependability. In the studies, the effectiveness of obstacle detec- tion, the system’s response time, and its practicality and usefulness for blind people are all measured. The findings show that the suggested obstacle detection method provides very accurate obstacle identification at a safe distance. Users who are blind or visually handicapped may successfully understand their surroundings thanks to the aural feedback system, which helps them to navigate by making judgments that are well-informed. Additionally, the system responds quickly, guaranteeing that the user receives real-time obstacle updates to increase safety and confidence while mov- ing. The study’s conclusions demonstrate the possibility of using the Arduino UNO board with the HC-SR04 ultrasonic sensor as a practical and affordable approach for detecting obstacles.

Phytoalexins are naturally-occurring molecules with antimicrobial activity deriving from the secondary metabolism of plants, which are synthesized in response to physical agents or stresses, phytopathogenic agents (fungi, bacteria and viruses) as well as numerous chemical compounds and biological control agents. Among these, grapevine phytoalexins, which belong to the chem-ical group of stilbenes, exhibit biocidal activity against a large number and a variety of plant pathogens. An important issue in research on these compounds is to be able to stimulate their synthesis in planta and to determine whether the induction of their production can serve as a basis for protecting that plant against its pathogens. Quite a few chemical compounds, derivatives of phytohormones bio-elicitors as well as biocontrol agents have been used to induce the synthesis of stilbene phytoalexins with the aim of conferring protection to grapevine against its main dis-eases (gray mold, downy mildew, powdery mildew and esca). This article reviews the experi-ments that have been carried out in this direction during the last thirty years and shows that the observed protective effects towards pathogens are generally linked to induction and priming of the grapevine phytoalexin response, confirming the interest of using, in a more general way, stimulation of the production of phytoalexins in plants as a basis for crop protection.

Conventional plant breeding methods exploit already existing genomic variation in plants to develop a variety in 8 to 10 years, which can decrease the genetic variability of the plant’s genome. The ever-increasing food demand for cereals crops cannot be met by traditional breeding methods. In order to increase food production in less time, there is a dire need to improve breeding methods. Several conventional and molecular breeding methods are being used to improve the crops traits. Molecular researchers have developed new genome editing tools like CRISPR/Cas9, CRISPR/Cpf1, prime editing, base editing, dcas9 epigenetic modification, and several other transgene-free genomes editing approaches. These genome editing tools can improve the desired traits precisely and efficiently. Moreover, a newly developed breeding method “Speed Breeding” has revolutionized the agriculture by shortening the crop cycle. It can produce 5-6 generations of cereals in a year. In this review, we have summarized all these conventional and molecular breeding approaches to improve cereal crops.

Aim: This analytical cross-sectional study aimed to examine whether there is a correlation between tumor differentiation and certain biomarkers in patients with hepatocellular carcinoma (HCC). Methods: Poorly differentiated (n=443), moderately differentiated (n=379), and well-differentiated (n=272) tumors were separated from the research population, along with a control group (n=364). Biopsies were used to establish the presence of HCC, and biomarker levels were analyzed using chemiluminescence immunoassays in both infected and uninfected individuals. Results: The correlation between age and tumor size was shown to be statistically significant (p0.05) across all subgroups using both descriptive and inferential statistics. Patients with hepatitis C virus and non-A, non-B hepatitis had more advanced tumors than those with other types of poorly differentiated liver cancer. Similarly, individuals with HBsAg and moderate differentiation had bigger tumors, although there was no correlation between hepatitis C and non-A, non-B. Patients with HBsAg or hepatitis C had bigger tumors in the well-differentiated group, albeit the hepatitis C connection was not statistically significant. In addition, the study stressed that tumor size increases with age and that farmers were the most commonly diagnosed profession category. Conclusions: It is clear that early detection in infected populations is crucial for improving HCC outcomes and that chemiluminescence immunoassay has the potential to be a helpful platform for biomarker research. However, the study is limited by its small sample size and its emphasis on only three tumor markers, indicating that more biomarker research is required to improve the accuracy of HCC diagnosis and prognosis.

Four new zoonotic coronaviruses outbreak occurred in the past two decades. The first coronavirus outbreak happened in 2003 and was named Severe Acute Respiratory Syndrome Coronavirus-1 (SARS-CoV-1), followed by Middle East Respiratory Syndrome Coronavirus (MERS-CoV) in 2013, and by Swine Acute Diarrhoea Syndrome (SADS) in 2017. In late December 2019, a patient from Wuhan Seafood Wholesale Market, China, was admitted to Huang's hospital with respiratory distress syndrome (RDS) of apparently unknown etiology, which later was diagnosed with SARS-CoV-2-induced coronavirus disease-19 (COVID-19). SARS-CoV-2 was identified from another clade within the subgenus Sarbecovirus of the genus Betacoronavirus. This new CoV variant showed 96.2% similarity at whole-genome level to bat coronavirus. Based on genetic studies, pangolin, bats, and snakes are suspected to be a possible intermediate host of this virus, but further research is in progress to determine how this virus appeared and what is the exact source of infection. The SARS-CoV-2 outbreak has higher transmissibility, contagiosity and pathogenicity compared to that of SARS-CoV-1 and MERS-CoV. SARS-CoV-2 swiftly spread from continent to continent and is persistently causing a shocking global public health concern albeit the rate of infected cases and mortality is relatively decreasing over time. In this review, we provide an update on the origin, transmissibility, etiology, epidemiology, and evolution of COVID-19. We also highlight the current diagnostics, therapies, and prognostics for SARS-CoV-2. Eventually, we report and provide our humble opinion about the preventive strategies to control the ongoing related pandemic situation at global and individual levels, considering the international public health emergency and possible future epidemics and pandemics.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.