The current study assessed the influence of Anti Stripping Agents (ASA), Ground Tire Rubber (GTR) and waste polyethylene terephthalate (PET) on performance behavior of binder and Stone Matrix Asphalt (SMA) mixtures. Through this paper, the 85/100 penetration grade bitumen was utilized as original bitumen. Also, three liquid ASA’s (ASA (A), ASA (B), ASA (C)) were used as a mixture modifier. For this purpose, softening point, penetration, rotational viscosity, Dynamic Shear Rheometer, Multi Stress Creep Recovery (MSCR) and Linear Amplitude Sweep (LAS) tests were implemented to investigate the rheological properties of modified bitumen. For evaluating the behavior of modified mixtures several tests such as; Resilient Modulus, Tensile Strength, dynamic creep, wheel track and four-point beam fatigue tests were implemented. Based on MSCR test results, utilization of mentioned polymers enhanced the elasticity of bitumens and therefore the permanent deformation resistance of binders increases. Also by the addition of PET percentage, the rutting resistance improves. Results indicated that utilization of ASAs, PET and Crumb Rubber (CR) enhance the Resilient Modulus (Mr), Indirect Tensile Strength (ITS), rutting resistance, fatigue life and Fracture Energy (FE) of asphalt mixtures. Also based on results, modification of binder by PET/CR with a ratio of 50%/50% and ASA (B) have the highest fatigue life which indicates that this mixture has highest resistance against fatigue cracking.

Abstract: Measures to counteract AMD generation need to start at the mineral surface, inhibiting mineral-oxidizing, acidophilic microbes. Laboratory and long-term field tests with pyrite-containing mining wastes, where Carbonaceous Phosphate Mining Waste (CPMW) was added, resulted in low acidity, and near neutral drainage. The effect was reproducible, nd confirmed by several independent research groups. This was shown to involve an organic coating, likely a biofilm. The biofilm formation was confirmed when CPMW was added to lignite coal waste with an initial pH of 1. Forty five days after the addition, the coal waste was dominated by heterotrophic microorganisms in biofilms. A review of the scientific literature supports that CPMW has physical and chemical characteristics which are capable of inducing a strong inhibitory effect on sulphide oxidation by forming an organic coating over the mineral surface. CPMW characteristics appear to provide the cornerstone of a new technology for the reduction of sulphide oxidation in mine wastes. An hypothesis for testing this technology is presented which could result in an economical and sustainable approach to mine waste and water management.

This study investigates the role of sustainable inventory management within supply chains, exploring strategies, benefits, challenges, and implications for organizations. Through qualitative research involving semi-structured interviews with supply chain professionals from diverse industries, key themes emerged. Sustainable practices such as green logistics, waste minimization, and ethical sourcing were identified as critical strategies to reduce environmental impact and enhance operational efficiency. Technological advancements, including AI, IoT, and blockchain, facilitate real-time monitoring, predictive analytics, and transparency, supporting data-driven decision-making in inventory management. Benefits include cost reduction, improved brand reputation, regulatory compliance, and risk mitigation, positioning organizations favorably in a competitive landscape shaped by environmental regulations and consumer expectations. Challenges such as cost constraints, regulatory complexities, and organizational inertia necessitate strategic investments, collaborative efforts, and leadership commitment to overcome. The study underscores the importance of integrating environmental, social, and economic considerations into supply chain practices to foster sustainability and resilience. Looking forward, the study advocates for a holistic approach to sustainable supply chain management, emphasizing innovation, stakeholder engagement, and capacity building. By aligning organizational values with societal expectations and regulatory frameworks, businesses can navigate complexities, drive positive environmental and social impacts, and achieve sustainable growth. This research contributes insights into current practices and future directions for sustainable inventory management, informing strategies that balance profitability with environmental stewardship and societal responsibility.

Cereal wastes such as rice bran and cereal dust are valuable yet underutilised by-products of grain processing. This study aimed to bio-convert these wastes into bacterial cellulose (BC), an emerging sustainable and renewable biomaterial, via an inexpensive solid-state fermentation (SSF) pre-treatment using three mould isolates. Medium substitution by directly using untreated rice bran or cereal dust did not significantly increase the yield of bacterial cellulose produced by a novel Novacetimonas sp. isolate (NCBI accession number PP421219) compared to the standard Hestrin-Schramm (HS) medium. In contrast, rice bran fermented with Rhizopus oligosporus yielded the highest bacterial cellulose (1.55 ± 0.6 g/L dry weight) compared to the untreated control (0.45 ± 0.1 g/L dry weight), demonstrating up to 22 % increase in yield. Using the SSF process, the media production costs were reduced by up to 90% compared to standard HS medium. Physicochemical characterisation using SEM, EDS, FTIR, XPS, XRD, and TGA were performed to gain insights into the internal structure, morphology, and chemical bonding of different produced BC, which revealed comparable biopolymer properties between BC produced in standard and waste-based media. Hence, our findings demonstrate the effectiveness of fungal SSF for transforming abundant cereal waste into BC, providing a circular economy solution to reduce waste and convert them into by-products to enhance the sustainability of the cereal industry.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Plant waste biomass is the most abundant renewable energy resource on Earth. The main problem of utilising this biomass in anaerobic digestion is the long and costly stage of degrading its complex structure into simple compounds. A promising solution to this problem are fungi of the Trichoderma genus, which show a high capacity to produce hydrolytic enzymes capable of degrading lignocellulosic biomass. This article discusses the structure of plant waste biomass and the problems resulting from its structure in the digestion process. It presents the methods of pre-treatment of lignocellulose with a particular focus on biological solutions. Based on the latest research findings, key parameters related to the application of Trichoderma sp. as a pre-treatment method are discussed. In addition, the possibility of using the digestate from agricultural biogas plants as a carrier for the multiplication of the Trichoderma sp. fungi, which are widely used in many industries, was discussed.

Municipal Solid Waste Management (MSWM) struggles with significant policy and operational challenges, particularly concerning recyclables collection routes and fleet composition. Within the European Union, phasing out traditional fuel-based vocational vehicles, like garbage trucks, in favor of zero-emission alternatives is mandatory to achieve sustainable development objectives. Integrating electric solid waste collection vehicles into municipal fleets presents challenges due to differences in range, capacity, and noise levels. The emission is even more crucial in the systems where recyclables are collected separately, which requires a greater number of trips to be performed. This study addresses MSWM’s strategic aspect by minimizing the total cost of replacing waste collection vehicles while meeting emission constraints. The Fleet Transition Problem (FTP) was formulated and solved using a MARKAL-based approach. The objective of the FTP and a mixed integer linear program used to solve it is minimizing the overall cost of fleet modernization throughout a multi-phase planning horizon so that the sustainable transition of the fleet can be assured. Computational experiments affirmed the model’s effectiveness in strategizing fleet transition. This research outlines a multi-period model for transitioning to a zero-emission fleet and demonstrates the FTP’s potential for strategic decision-making. Notably, the study observes a consistent reduction in permissible emissions across the planning horizon.

The concept of biorefinery constitutes a significant contributing factor to the emerging transition towards a sustainable bioeconomy. In such a context, replacing oil and petrochemicals by biomass may involve several feedstocks, platforms, processes, technologies, as well as final products. This paper concentrates in the complex process of transferring the concept of biorefinery from laboratory to industry, and sheds light on the techno-economic, and complexity management dimensions involved in this endeavor. Towards this end, adopting a systems perspective, the paper presents a structured and comprehensive framework, comprising of the definition of the transformation process, business model development, technoeconomic assessment and strategic positioning and viability assessment, which may be employed to facilitate the engineering at-large and launch of a biorefining venture in a circular bioeconomy context. The framework is applied in the context of a biorefinery plant in a specific region in Southern Greece, which is based on the valorisation of olive mill wastewater (a ‘strong’ and quite common industrial waste in Mediterranean Basin), and produces biopolymers (PHAs) and bioenergy (H2).

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

Abstract: The promotion of sustainable packaging is part of the European Green Deal and plays a key role in the EU’s social and political strategy. One option is the use of renewable resources and biomass waste as raw materials for polymer production. Lignocellulose biomass from annual and perennial industrial crops and agricultural residues are a major source of polysaccharides, proteins, and lignin, and can also be used to obtain plant-based extracts and essential oils. Therefore, these biomasses are considered as potential substitute for fossil-based resources. Here, the status quo of bio-based polymers is discussed and evaluated in terms of properties related to packaging applications such as gas and water vapor permeability as well as mechanical properties. So far, their practical use is still restricted due to lower performance in fundamental packaging functions that directly influence food quality and safety, the length of shelf life and thus the amount of food waste. Besides bio-based polymers, this review focuses on plant extracts as active packaging agents. Incorporating extracts of herbs, flowers, trees, and their fruits is inevitable to achieve desired material properties that are capable to prolong the food shelf life. Finally, the adoption potential of packaging based on polymers from renewable resources is discussed from a bioeconomy perspective.

The slate aggregate has long been perceived as a substandard, low quality waste material with its physical and chemical properties not being competitive with those of the primary aggregates. It is assumed that the slate aggregate particles are not strong, that is not durable and will not compact. This research aims to address those claims and review the available literature on the performance of the slate aggregate. The review inaugurates by analysing the physical, chemical and mechanical properties of slate, before expanding into a literature review of laboratory testing’s on the effect of moisture content on density, compaction and layer thickness of slate aggregate.The paper reviews case studies of construction projects in North Wales, where the slate aggregate has been used for general fill and road building for many years. Some of the case studies include the A55 coastal road and duelling of the A5 in Anglesey (WRAP, 2004), where slate aggregate was successfully used as sub-base. The paper also investigates why many civil engineers are reluctant to use the slate aggregate and regard the material as sub-standard, flaky aggregate. The research paper reviews the potential usages and various products the slate aggregate is suitable for and satisfies the requested standards. The final topic reviewed is the cost of transporting slate aggregate compared with the cost of transport for primary aggregate and the introduction of the Primary Aggregates Tax (Parliament of the United Kingdom, 2011). The last topic includes a critical analyses of the claims that the slate aggregate a commercially viable construction material despite its remote location (Woodward et al, 2004). The transportation cost and the supply chain complexities must be evaluated prior to considering the long-term sustainability of the product (Radanliev et al^1-6, 2014, 2015, 2016).

The next-generation "Industrial Internet of Things" (IIoT) will support "Machine-to-Machine" (M2M) communications for smart Cyber-Physical-Systems and Industry 4.0, and require guaranteed cyber-security. This paper explores hardware-enforced cyber-security for critical infrastructures. It examines a Quantum-Safe "Software-Defined Deterministic IIoT" (SDD-IIoT), with a new forwarding-plane (sub-layer-3a) for deterministic M2M traffic flows. A "Software-Defined-Networking" (SDN) control-plane controls many "SDD Wide Area Networks" (SDD-WANs), realized with FPGAs. The SDN control-plane provides an "Admission-Control/Access-Control" system for network-bandwidth, using collaborating Artificial Intelligence (AI) rule-based "Zero Trust Architectures" (ZTAs). Hardware-enforced access-control eliminates all congestion, BufferBloat, and DoS/DDoS attacks in the forwarding-plane, reduces buffer-sizes by 100,000+ times, and supports ultra-reliable and uItra-low-latency communications in the SDD-WANs. The SDD-WANs can: (i) Encrypt/Authenticate M2M flows using Quantum-Safe ciphers, to withstand attacks by Quantum Computers; (ii) Implement "Guaranteed Intrusion Detection Systems" in FPGAs, to detect cyber-attacks embedded within billions of IIoT packets/second; (iii) Provide guaranteed immunity to external cyber-attacks against critical infrastructure, and exceptionally-strong immunity to internal cyber-attacks; (iv) Save $US100s of billions annually by exploiting FPGAs; and (v) Enable "Quantum Key Distribution" (QKD) Networks by providing a programmable forwarding-plane with "authenticated classical channels" and full-immunity to DoS/DDoS attacks. Extensive experimental results for an SDD-WAN over the European Union are reported.

This study examines the attitudes and practices of dentists and dental students towards envi-ronmental issues within their professional context. Data was selected based on their responses on a Google Forms e-questionnaire, designed specifically for the study. The sample consisted of 78 professional dentists and 75 dental students in Greece and their attitudes towards environmental protection, awareness of the environmental impact of dental practices, and factors influencing the adoption of environmentally friendly practices were assessed. Results reveal generally positive attitudes towards environmental protection, with students demonstrating higher levels of proper waste management practices. Dentists express awareness of their environmental impact but ex-hibit varying levels of engagement in eco-friendly practices. Factors such as moral consciousness and believing in the severity of climate change significantly influence environmental awareness in dental practice. Notably, dental students exhibit greater environmental awareness compared to practicing dentists. These findings emphasize the importance of integrating environmental edu-cation into dental curricula and continuing education programs to foster sustainable practices in dental care. Future research could explore interventions to enhance environmental consciousness among practicing dentists and assess the long-term impact of environmental education initiatives on dental care sustainability.

This study provides a detailed investigation into the pathways through which microplastics from urban sources are transported to marine ecosystems, their distribution across different environments, and their impacts on marine life. Utilizing a combination of water and sediment sampling across urban, riverine, and marine environments, the research quantitatively assesses the concentration and types of microplastics present, and evaluates the ecological consequences of their accumulation in marine ecosystems. The findings reveal a significant concentration of microplastics in all examined environments, with the highest levels detected in urban areas, closely linked to industrial activities and inadequate waste management practices. The study documents a variety of microplastic polymers, with polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET) being the most prevalent. A substantial impact on marine organisms was observed, including evidence of microplastic ingestion across a wide range of species and indications of stress and physical damage to coral reefs. Seasonal variations indicate that microplastic concentrations peak during periods of high rainfall, suggesting urban runoff as a critical pathway for microplastic transport. The study concludes with recommendations for improving waste management practices, enhancing public awareness and engagement in plastic recycling efforts, and implementing policies aimed at reducing the production and use of single-use plastics. This research underscores the urgent need for coordinated actions to mitigate the pervasive issue of microplastic pollution, highlighting the role of urban management and policy interventions in safeguarding marine ecosystems.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

White-rot fungi (WRF) have specific enzymes to degrade lignocellulosic and phenolic compounds. Therefore, their direct application could be an alternative to biodegrade complex lignocellulosic biomass such as olive mill solid waste (OMSW). The aim of this study was to evaluate the capacity of A. discolor and S. hirsutum to grow in OMSW as the sole substrate under static conditions and evaluate the phenolic removal compounds and lignin degradation. The lignolytic enzyme activity was determined, as was the phenolic compound removal. At the same time, lignin degradation and structural changes were evaluated by confocal laser scanning microscopy (CLSM) and scanning electron microscope (SEM), respectively. Both strains were able to grow using OMSW as the sole substrate without adding other nutrients, oxygen and/or agitation. The higher ligninolytic enzyme activity was found at day 8, and the highest phenolic removal (more than 80% with both strains) was reached after 24 days of incubation. The CLSM analysis confirmed lignin degradation through the drop in lignin fluorescence from 3967 for untreated OMSW to 235 and 221 RFU after 24 days of treatment by A. discolor and S. hirsutum respectively. The results indicate that both WRF could be suitable candidates to design an in-situ pretreatment step of OMSW, as long as in future research the WRFs have the same performance in non-sterile conditions.

Poland is the 3^rdproducer of mushrooms in the world. Mushroom production in Poland accounts for nearly 25% of the total production in the EU, and it is still growing. One type of waste generated during mushroom production is mushroom spent compost (MSC), with a 5:1 (MSC: mushrooms) production rate. We investigated valorizing the MSC to produce fuel via torrefaction (‘roasting’, a.k.a. low-temperature pyrolysis). Specifically, we developed models for the MSC torrefaction kinetics using thermogravimetric analyses (TGA) and the effects of torrefaction temperature (200~300 °C) and process duration time (20~60 min) on the resulting biochar (fuel) properties. The estimated activation energy value of MSC torrefaction was 22.3 kJ^.mol^-1. The highest higher heating value(HHV) = 17.9 MJ^.kg^-1d.m. was found for 280 °C (60 min torrefaction time). The temperature of torrefaction significantly (p<0.05) increased the HHVfor constant process duration. The torrefaction duration time significantly (p<0.05) increased the HHVfor 220 °C and decreased HHVfor 300 °C. The highest mass yield 98.5% was found for 220 °C (60 min), while the highest energy yield was found for 280 °C (60 min). In addition, estimations of the value (€132.3·Mg^-1d.m. or 27.7 €·Mg^-1w.m) and quantity of resulting biochar (from torrefied MSC with 65.3% moisture content) were made based on the 280°C (60 min) torrefaction variant, assuming the price of commercially available coal fuel. We have shown a concept for an alternative utilization of abundant biowaste (MSC). The initial economic evaluation showed that MSC torrefaction might be profitable. This research provides a basis for alternative use of an abundant biowaste and can help charting improved, sustainable mushroom production.

Is it true that the nuclear technology applied to electric energy generation offers a clean, safe, reliable and affordable i.e. sustainable alternative? Yes it is, but its impact on the environment strongly depends on the implementation bearing residual risks due to a human factor, technical failures or natural catastrophes. A full response is therefore difficult and can first be given when the wicked multi-disciplinary problems get well formulated and “solved”. These problems have multi-dimensional nature lying at the interface between: necessary R&D effort, the industrial deployment and the technology impact in view of the environmental sustainability including the management of produced hazardous waste. This enormous complexity indicates that just a description of the problem might represent a problem. The paper proposes a holistic approach to assess the nuclear energy systems potential with respect to sustainable performance applying Multi-criteria decision analysis with a suitable objective tree and a multi-level criteria structure and examines the trading-off techniques for ranking of the alternatives. The framework proposes a multi-criteria and multi-stakeholders treatment which can be used as a pre-decisional support towards an implementation of nuclear fuel cycles adapted to national preferences and priorities. Proposed approach addresses some aspects of the environmental footprint of nuclear energy systems. Advanced nuclear fuel cycles, previously investigated by the NEA/OECD expert group WASTEMAN, are analyzed as a case study. Sustainability facets of waste management, resource utilization and economics are in focus.

Marine litter, comprising persistent and human-made solid materials discarded in marine environments, poses a severe threat to Nigeria's coastal and marine ecosystems. Despite existing international, regional, and national regulations, ineffective enforcement and compliance have led to widespread environmental degradation (UNEP, 2021). This study examines the factors contributing to the proliferation of marine litter in Nigeria, focusing on regulatory gaps, insufficient waste management infrastructure, and the lack of public awareness. The findings reveal that the marine ecosystem is deteriorating due to inadequate waste disposal practices and limited understanding of the impacts of marine litter on both the environment and human health (UNEP, 2021). The paper concludes with recommendations for improving regulatory enforcement, enhancing public education, and investing in waste management infrastructure to address the growing crisis of marine litter. Throughout this article, the limited information on the impacts of marine pollution across Africa is highlighted, emphasizing the value of these insights despite their scarcity.

Industrial fires at facilities including waste management sites, warehouses, factories, chemical works and fuel storage depots are relatively frequent occurrences. Often, these fires occur adjacent to urban communities and result in ground-level airborne pollutant concentrations that are well above guideline values. Land, water, livestock and crops may also be contaminated by the emissions and by firefighting activities. Moreover, impacted communities tend to have a higher proportion of minority ethnic populations, individuals with underlying health vulnerabilities, as well as those of lower socio-economic status. Nevertheless, this is an aspect of air quality that is under-researched, and so this review aims to highlight the public health hazards associated with industrial fires and the need for an effective, coordinated, public health response. We also review the range of monitoring techniques that have been utilised in such fires and highlight the role of dispersion modelling in predicting plume trajectories and in estimating population exposure. We recommend establishing 1-h guideline values for particulate matter to facilitate timely public health interventions and we highlight the need to review regulatory and technical controls for sites prone to fires, particularly in the waste sector.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Traditionally there is a gap between reactor operation and the consideration of nuclear waste in the final disposal. Fuel is produced and fuel must be disposed of in the view of the reactor operator, fuel has to be cleaned in the reprocessing and new solid fuel has to be produced in the view of the chemist. iMAGINE is designed to overcome this separation through the breakthrough development applying an optimized, integrative approach from cradle to grave of nuclear energy production as a first step to come as close as possible to the vision of zero waste nuclear power. It is described here the first time all in three the steps: reactor, fuel cycle, waste, providing the ratio behind each of the choices taken to come to the overall solution to open the discussion and thinking process on what could be achieved by a really innovative approach to integrated nuclear energy production. The opportunities regarding the handling of the remaining waste will be discussed with a view on the expectation of the final disposal community, the study ‘Nuclear waste from small modular reactors’, and the IAEA report ‘waste from innovative types of reactors and fuel cycles - a preliminary study. The aim of the is not to find answers to each of the raised points, but to identify first potential approaches and potentially promising ways to go, as well as to stimulate a discussion among experts. In the best case this could lead to a change of track for nuclear to become an even more sustainable and at least as important, trusted technology to help solve the net-zero challenge.

UV-A (ca. 365 nm wavelength, a.k.a. 'black light') photocatalysis has been investigated to comprehensively mitigate odor and selected air pollutants in the livestock environment. This study was conducted to confirm the performance of UV-A photocatalysis on the swine farm. The objectives of this research were to (1) scale-up of the UV-A photocatalysis treatment, (2) evaluate the mitigation of odorous gases from swine slurry pit, and (3) test different UV sources, (4) evaluate the effect of suspended particulate matter (PM), and (5) conduct preliminary economic analyses. We tested UV-A photocatalysis at a mobile laboratory-scale capable of treating ~0.2 - 0.8 m3·s-1 of barn exhaust air. The targeted gaseous emissions of barn exhaust air were significantly mitigated (p < 0.05) up to 40% reduction of measured odor; 63%, 44%, 32%, 40%, 66%, and 49% reduction of dimethyl disulfide, isobutyric acid, butanoic acid, p-cresol, indole, and skatole, respectively; 40% reduction of H2S; 100% reduction of O3; and 13% reduction of N2O. The PM mitigation effect was not significant. Formaldehyde levels did not change, and a 21% generation of CO2 was observed. The percent reduction of targeted gases decreased as the airborne PM increased. Simultaneous chemical and sensory analysis confirmed that UV-A treatment changed the overall nuisance odor character of swine barn emissions into weaker manure odor with 'toothpaste and 'mint' notes. The smell of benzoic acid generated in UV-A treatment was likely one of the compounds responsible for the less-offensive overall odor character of the UV-treated emissions. Results are needed to inform the design of a farm-scale trial, where the interior barn walls can be treated with the photocatalyst, and foul air will be passively treated as it moves through the barn.

Environmental impact associated with odor and gaseous emissions from animal manure is one of the challenges for communities, farmers, and regulatory agencies. Microbe-based manure additives treatments are marketed and used by farmers for mitigation of emissions. However, their performance is difficult to assess objectively. Thus, comprehensive, practical, and low-cost treatments are still in demand. We have been advancing such treatments based on physicochemical principles. The objective of this research was to test the effect of the surficial application of a thin layer (¼"; 6.3 mm) of biochar on the mitigation of gaseous emissions (as the percent reduction, % R) from swine manure. Two types of biochar were tested: highly alkaline and porous (HAP) biochar made from corn stover and red oak (RO), both with different pH and morphology. Three 30-day trials were conducted with a layer of HAP and RO (2.0 & 1.65 kg∙m^-2, respectively) applied on manure surface, and emissions of ammonia (NH₃), hydrogen sulfide (H₂S), greenhouse gases (GHG), and odorous volatile organic compounds (VOCs) were measured. The manure and biochar type and properties had an impact on the mitigation effect and its duration. RO significantly reduced NH₃ (19-39%) and p-cresol (66-78%). H₂S was mitigated (16~23%), but not significantly for all trials. Significant (66~78%) reductions for p-cresol were observed for all trials. The phenolic VOCs had relatively high % R in most trials but not significantly for all trials. HAP reduced NH₃ (4~21%) and H₂S (2~22%), but not significantly for all trials. Significant % R for p-cresol (91~97%) and skatole (74~95%) were observed for all trials. The % R for phenol and indole ranged from (60~99%) & (29~94%) but was not significant for all trials. The impact on GHGs, isobutyric acid, and the odor was mixed with some mitigation and generation effects. However, larger-scale experiments are needed to understand how biochar properties and the dose and frequency of application can be optimized to mitigate odor and gaseous emissions from swine manure. The lessons learned can also be applicable to surficial biochar treatment of gaseous emissions from other waste and area sources.

This article attempts to identify factors impacting on the quantity of municipal waste in Polish 2478 communes (LAU-2), taking into account the variability of particular determinants influence depending on their regional diversification. The analysis covers the years 2005-2018. The dependent variable is the volume of municipal waste in kg per capita, whereas the group of determinants include: economic and human development, uncontrolled dumping sites, population density, population at the working age, migration, tourism, urbanization, dwellings and housing, retail sales, entities, education and investments in waste management; The geographically weighted regression with spatial error term (GWR-SEM) was employed in this study. The model enabled not only the specification of the waste production determinants, but also the analysis of the variability in the strength and direction of dependencies occurring between the examined variables in individual communes. The results proved that the higher the level of education the less waste is generated (in the north-central Poland); the business entities and working-age population are crucial for the waste quantity in communes of eastern Poland; the factors most considerably as to regional range affecting the waste quantity are urban and business development; as to strength–higher education and the share of working age individuals;

In this study, the effects of food waste (FW) compost, vermicompost, and chemical fertilizers on the growth of organic red radish and soil quality are investigated to promote sustainable agriculture. Utilizing a comparative approach, it assesses the impacts of these fertilizers on various plant growth metrics and soil characteristics, highlighting the potential of converting FW into nutrient-rich amendments as a sustainable alternative to chemical fertilizers. The results indicate a significant variation in fresh weight among different treatments. For example, the FV 25% treatment demonstrated a relatively high mean fresh weight of 7.9664, while the CO 50% treatment yielded a much lower mean fresh weight of 0.2589. These numbers underscore the potential efficacy of specific FW treatments in enhancing plant growth, with VC 50% and FV 25% showing considerable promise in increasing crop yield. The study concludes that FW compost and vermicompost significantly enhance plant growth and soil quality, advocating for their use as sustainable and environmentally friendly alternatives to chemical fertilizers. The findings emphasize the importance of selecting appropriate fertilizer types and concentrations to optimize agricultural productivity and environmental sustainability, supporting the incorporation of FW into agricultural systems as a beneficial resource.

Coffee processing generates a huge amount of waste which contains many natural products. Here, we report the discovery of a panel novel cell-penetrating and metal-ion binding microproteins designated coffeetide cC1a-c and cL1-6 from the husk of two popular coffee plants, Coffea canephora and Coffea liberica, respectively. Combining sequence determination and database search, we showed that the prototypic coffeetide cC1a is a 37-residue, eight-cysteine microprotein with a hevein-like cysteine motif but without a chitin-binding domain. NMR determination of cC1a revealed a compact structure that confers it resistance to heat and proteolytic degradation. Disulfide mapping together with chemical synthesis revealed that cC1a has a ginsentide-like, and not a hevein-like, disulfide connectivity. In addition, transcriptomic analysis showed that the 98-residue micrcoproten-like coffeetide precursor contains a three-domain arrangement like ginsentide precursors. Molecular modeling together with experimental validation revealed a Mg2+ and Fe3+ binding pocket at the N-terminus formed by three glutamic acids. Importantly, cC1a is amphipathic with a continuous stretch of 19 apolar amino acids, and which enables its cell penetration to target intracellular proteins, despite being highly negatively charged. Our findings suggest that coffee by-products could provide a source of ginsentide-like bioactive peptides that have potential to target intracellular proteins.

The use of mixed-state ionic beams in collision dynamics investigations is examined. Using high resolution Auger projectile spectroscopy involving He-like ($1s^2\thinspace^1\!S, 1s2s\thinspace^{3,1}\!S$) mixed-state beams, the spectrum contributions of the $1s2s\thinspace^3\!S$ metastable beam component is effectively separated and clearly identified. This is performed with a technique that exploits two independent spectrum measurements under the same collision conditions, but with ions having quite different metastable fractions, judiciously selected by varying the ion beam charge-stripping conditions. Details of the technique are presented together with characteristic examples. In collisions of 4 MeV B$^{3+}$ with H$_2$ targets, the Auger electron spectrum of the separated $1s2s\thinspace^{3}S$ boron beam component allows for a detailed analysis of the formation of the $1s2s(^3\!S)nl \thinspace^2\!L$ states by direct $nl$ transfer. In addition, the production of hollow $2s2p\thinspace^{1,3}\!P$ doubly- and $2s2p^2\thinspace^2\!D$ triply-excited states, by direct excitation and transfer-excitation processes, respectively, can also be independently studied. In similar mixed-state beam collisions of 15 MeV C$^{4+}$ with H$_2$, He, Ne and Ar targets, the contributions of the $1s^2$, $1s2s\thinspace^{3,1}S$ beam components to the formation of the $2s2p\thinspace^{3,1}\!P$ states by double-excitation, $1s\rightarrow2p$ excitation and transfer-loss processes can be clearly identified, facilitating comparisons with theoretical calculations.

Effective waste elimination is critical for the success of construction projects. Although several studies have focused on various aspects of construction waste, limited efforts have investigated the dynamic effect of Making-Do (MD) practices on productivity, rework, defects, and materials wastage. From a lean construction perspective, this study aims to address MD waste using the Last Planner System (LPS) and BIM. First, the casual structure that can cause MD in construction projects was expressed in a casual loop diagram (CLD), and thematic analysis uncovered the strategies of LPS-BIM to eliminate MD identified by reviewing the literature. Secondly, twenty-five strategies from the LPS and BIM strategies to address MD using Structural Equation Modeling (SEM) were assessed. Subsequently, a system dynamics model (SDM) for investigating LPS-BIM strategies on MD decisions in a construction project was formulated based on the underlying causal loop diagrams and the mathematical relations among the variables. Finally, the model was applied to three projects, and simulations for four LPS-BIM scenarios were carried out. The findings show that dynamic interactions among diverse production planning and control factors are critical in evaluating MD impacts on a construction project. The results demonstrate that the LPS-BIM approach resulted in an average 43.8% reduction in the tasks performed with MD, 45.3% of constraints, 66.5% of construction waste, increasing 13.7% completion rate, and 29.3% cost reduction, demonstrating that LPS-BIM as a more efficient solution for MD mitigation and construction planning.

Currently, there is increasing industrial demand for rare earth elements (REE) as these elements are now integral to the manufacture of many carbon-neutral technologies. The depleting REE ores and increasing mining costs are prompting to look for alternative sources for these valuable metals, particularly from waste streams. Although REE concentrations in most of the alternate resources are lower than current REE ores, some sources such as marine sediments, coal ash, and industrial wastes like red mud are looking promising with significant concentrations of REE in them. This review focuses on the alternative resources for REE such as ocean bottom sediments, continental shelf sediments, river sediments, stream sediments, lake sediments, phosphorites deposits, industrial waste products like red mud, and phosphogypsum, coal, coal fly ash, and related materials, waste rock sources from old and closed mines, acid mine drainage, and recycling of e-waste. Possible future Moon exploration and mining for REE and other valuable minerals are also discussed. It is evident that REE extractions from both primary and secondary ores alone are not adequate to meet the current demand, and sustainable REE recovery from the alternative resources described here is also necessary to meet the growing REE demand. An attempt is made to identify the potential of these alternative resources and sustainability challenges, benefits, and possible environmental hazards to meet the growing challenges in meeting the future REE requirements.

This paper responds to the research question, “can urban farming help Nepali cities become more sustainable”? Especially after the Covid-19 pandemic, urban residents have begun to realize that food transported from long distances could not always be reliable. Urban farming can help produce fresh food locally and avoid long-distance transportation, and refrigeration. This practice also helps reduce greenhouse gases through plant carbon use efficiency (CUE). Urban farming not only helps city-dwellers towards achieving self-reliance in food production but also in vegetation carbon dynamics (VCD) while supporting the circular economy. Urban farming consists of edible landscapes, which can also be an aesthetic public space. As urban lands command higher prices than agricultural land, urban farming usually happens on residential yards, roofs, balconies, community gardens, and dedicated areas in public parks. Rainwater harvesting, and redirecting can help irrigate urban farms which can be part of rain gardens. The national census of 2021 (CBS 2022, p5) identifies that 66 percent of Nepal’s population live in urban areas. However, the World Bank (2018), shows that only 21 of Nepal’s population was projected to live in urban areas in 2021. It is not debatable that the urbanization process in Nepal is on the rise. Thus, urban agriculture can play an important role to supplement the residents’ food needs. Many cities in Nepal have already successfully adapted to urban farming where residents grow food on their building site, balconies, and rooftop often growing plants on pots, vases, and other types of containers. The UN-Habitat, with the support of European Union and local agencies, has published a rooftop farming training manual (2014) showing the feasibility of urban farming in Nepal.The paper discusses how Public Private Partnership (PPP) can promote urban agriculture and make the process more effective and attractive to urban farming households. It also analyzes how a PPP approach also facilitates the use of better technology, advisory support, and use of research extension activities. This paper draws on literature review, secondary data (e.g., from National Census Nepal 2021) and authors’ professional experiences related to best practices in the areas to analyze the benefits and challenges related to urban farming in Arizona, USA. The paper will provide recommendations for Nepali cities to maximize the benefit provided by urban farming. It is expected to be useful to Nepali policy makers, and government agencies, and nonprofit organizations which promote sustainability, and organic farming.

Recent studies have demonstrated silk fibroin’s ability to extend the shelf life of foods by mitigating the hallmarks of spoilage, namely oxidation and dehydration. Due to the potential for this protein to become more widespread, its safety was evaluated comprehensively. First, a bacterial reverse mutation test (Ames test) was conducted in five bacterial strains. Second, an in vivo erythrocyte test was conducted with Sprague Dawley rats at doses up to 1,000mg/kg-bw/day. Third, a range-finder study was conducted with Sprague Dawley rats at the highest consumption amount given solubility and oral gavage volume constrains (500mg/kg-bw/day). Fourth, a 28-day study in Sprague Dawley rats was conducted at the 500mg/kg-bw/day amount. Fifth, an in vitro pepsin digestion assay was performed to assess the potential for protein allergenicity. Sixth, allergenic potential was further assessed using liquid chromatography-mass spectroscopy for detection of allergenic insect proteins. Seventh, the protein sequences were subjected to bioinformatic analyses. Together, these studies raise no mutagenic, carcinogenic, toxicological, or allergenic concerns with the oral consumption of silk fibroin.

Clock Network Design (CDN) is a critical step while designing any Integrated-Circuits (ICs). It holds vital importance in the performance of entire circuit. Due to continuous scaling, 3D ICs stacked with TSV are gaining importance, with an objective to continue with the Moore's law. Through-Silicon-Via (TSV) provides the vertical interconnection between two die, which allows the electrical signal to flow through it. 3D ICs has many advantages over conventional 2D planar ICs like reduced power, area, cost, wire-length etc. The proposed work is mainly focused on power reduction and obstacle avoidance for 3D ICs. Various techniques have already been introduced for minimizing clock power within specified clock constraints of the 3D CND network. Proposed 3D Clock Tree Synthesis (CTS) is a combination of various algorithms with an objective to meet reduction in power as well as avoidance of obstacle or blockages while routing the clock signal from one sink to other sink. These blockages like RAM, ROM, PLL etc. are fixed during the placement process. The work is carried out mainly in three steps- first is Generation of 3D Clock tree avoiding the blockages, then Buffering and Embedding and finally validating the results by SPICE simulation. The experimental result shows that our CTS approach results in significant 9% reduction in power as compare to the existing work.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

The demand for improving the nuclear waste management has since long been identified as one of the major hurdles for widespread use of nuclear energy. Nuclear waste management, through partitioning and transmutation (P&T) has been researched since the 1990ies with partitioning being a pre-requisite for the process. Recently, an innovative approach of reactors directly operating on spent nuclear fuel, iMAGINE, has been proposed which could deliver on the aims of P&T as a side effect to more efficient nuclear energy production in the future. The results shown here confirm that it is possible to achieve the aims of P&T without prior partitioning, but it is certainly less efficient since the high concentration of MAs, required for efficient burning, are impossible to obtain in a short operational time. The proposed nuclear waste management approach will be a long-term effort when it is accomplished without partitioning/separation technologies. However, none of the analyses contradicts this effort – the key points are a) when the technology for treating the waste is possible and reliable, the time horizon will not be a major concern b) the waste management is now intrinsically linked with energy production instead of requiring dedicated costly facilities, delivering a promising economic basis c) the waste management is now associated with long-term energy production and massively improved resource utilization. In summary, the objectives of P&T are achievable without prior partitioning – this is a ground-breaking result. However, the approach will require continued nuclear energy production for a very long time. In case of a nuclear phase-out decision, a much more efficient transmutation scenario would have to be envisaged as already discussed several years ago for Germany.

The study on graphs emerging from different algebraic structures like groups, rings, fields, vector spaces, etc. is a prominent area of research in mathematics, as algebra and graph theory are two mathematical fields that focuses on creating and analysing structures. There are numerous studies linking algebraic structures and graphs, which began with the introduction of Cayley graphs of groups. Several algebraic graphs have been defined on rings, which have huge-growing literature. In this article, we systematically review the literature on some variants of Cayley graphs that are defined on rings, to understand the research in this area.

We present an overview over eight brightly luminescent Cu(I) dimers of the type Cu2X2(PN)3 with X = Cl, Br, I and P^N = 2-diphenylphosphino-pyridine (Ph2Ppy), 2-diphenylphosphino-pyrimidine (Ph2Ppym), 1-diphenylphosphino-isoquinoline (Ph2Piqn) including three new crystal structures (Cu2Br2(Ph2Ppy)3, 1-Br, Cu2I2(Ph2Ppym)3, 2-I, and Cu2I2(Ph2Piqn)3, 3-I). However, we mainly focus on their photo-luminescence properties. All compounds exhibit combined thermally activated delayed fluorescence (TADF) and phosphorescence at ambient temperature. Emission color, decay time, and quantum yield varies over large ranges. For deeper characterization, we select Cu2I2(Ph2Ppy)3, 1-I, showing a quantum yield of 81 %. DFT and SOC-TDDFT calculations provide insight into the electronic structures of the singlet S1 and triplet T1 states. Both stem from metal+iodide-to-ligand charge transfer transitions. Evaluation of the emission decay dynamics, measured from 1.2 ≤ T ≤ 300 K, gives ∆E(S1-T1) = 380 cm-1 (47 meV), a transition rate of k(S1→S0) = 2.25×106 s-1 (445 ns), T1 zero-field splittings, transition rates from the triplet substates, and spin-lattice relaxation times. We also discuss the interplay of S1-TADF and T1-phosphorescence. The combined emission paths shorten the overall decay time. For OLED applications, utilization of both singlet and triplet harvesting can be highly favorable for improvement of the device performance.

This article seeks to strengthen efforts in technological developments based on the classification of PET plastic that positively impacts sustainable development and contributes to suitable solutions in collection centers in Mexico. Three experiment designs and machine learning tools for data processing were developed. For the experimentation, three factors were considered: the bottle's size, the amount of liquids inside the bottle, and the label on the bottle. The first experiment was to identify the distance of the sensor from post-consumer PET bottles. The second experiment was to determine the detection ability of the sensor with different levels of liquids inside the bottles, and the third was to determine the detection ability on the bottle labels. A digital lux meter on a microcontroller was developed to monitor illuminance on post-consumer PET plastic when it contains liquid as it passes through a conveyor belt for processing at an average rate of three bottles per second. With the implemented methodology, liquids were satisfactorily detected inside the transparent PET bottles when they had beverages between 25% and 100% of their capacity. Finally, this paper highlights that it is possible to implement an affordable design to identify bottles with liquids for collection centers.