In this study, the effect of extraction conditions on the total phenolic content of clove buds was investigated. Clove buds were extracted using a deep eutectic solvents like mixtures choline chloride: lactic acid in the 1:2 molar ratio. Additionally, the HPLC-DAD method was used to determine the main components of the clove extracts, including eugenol, eugenol acetate, and β-caryophyllene. The conditions used in the extraction with choline chloride: lactic acid (molar ratio 1:2) included extraction temperature (t = 40 – 80°C), water addition (5.6 – 40%), and extraction time (30 – 90 min). Determination of the phenolic compounds was done by the Folin-Ciocalteu method. The optimum operating conditions for the total phenolic content were identified at 77°C, 30 min, and a water addition of 40%. Based on the results, the highest amount of eugenol (307.26 ± 8,44 mg/g dry raw material) was determined in clove extracts which were extracted under condition of 60°C, 22.8%, and 30 min.

Nuclear magnetic resonance (NMR) techniques are widely used to identify pure substances and probe protein dynamics. Edible oil is a complex mixture composed of hydrocarbons, which have a wide range of molecular size distribution. In this research, low field NMR (LF-NMR) relaxation characteristic data of various sample oils were analyzed. We also suggest a new method for prediction size of edible oil molecules using LF-NMR relaxation time distributions. According to the relative molecular mass, carbon chain length, transverse relaxation time of different sample oils, combined with oil viscosity and other factors, the relationship between carbon chain length and transverse relaxation time rate was analyzed. Various oils and fats in the mixed fluid are displayed, reflecting the composition information of different oils. To study the correlation between the rotation correlation time and molecular information of oil molecules. The molecular composition of the resulting fluid determines its properties, such as viscosity and phase behavior. The results show that low-field NMR can obtain information on the composition, macromolecular aggregation, and molecular dynamics of complex fluids. Measurements of grease in the free fluid state show that the relaxation time can reflect the intrinsic properties of the fluid. It is shown that the composition characteristics and states of complex fluids can be measured by low-field nuclear magnetic resonance.

As the global energy crisis continues, efficient hydrogen production is one of the hottest topics these days. In this sense, establishing catalytic trends for hydrogen production is essential for choosing proper H2 generation technology and catalytic material. Volcano plots for hydrogen evolution in acidic media are well-known, while volcano plot in alkaline media was constructed ten years ago using theoretically calculated hydrogen binding energies. Here we show for the first time that the volcano-type relationships are largely maintained in a wide range of pH values, from acidic to neutral and alkaline solutions, using theoretically calculated hydrogen binding energies on clean metallic surfaces and experimentally measured hydrogen evolution overpotentials. If metallic surfaces are exposed to high anodic potentials, hydrogen evolution can be boosted or significantly impeded, depending on the metal and the electrolyte in which the reaction occurs. Such effects are discussed here and can be used to properly tailor catalytic materials for hydrogen production via different water electrolysis technologies.

Asphaltene is a component of crude oil that, if mishandled, may create substantial transportation and industrial concerns. It is a solid by nature, with a diverse set of molecular compositions. Furthermore, the oil industry has identified emulsion generation and clogging precipitate as key concerns. The emulsified water droplets in the process are just what give the raw oil its increased viscosity; hence, power is squandered to transport the oil around. The information has been separated into sections based on simulation, solubilization, agglomeration, precipitation, and evidence of model chemicals in the literature. We have included research that investigates the bulk rheology and interfacial rheology of asphaltene to describe its interfacial activity more clearly.

Electron can tunnel between cofactor molecules positioned along biological electron transport chains up to the distance of ≃20 Å on the millisecond time scale of enzymatic turnover. This tunneling range mostly determines the design of biological energy chains facilitating cross-membrane transport of electrons. Tunneling distance and cofactors’ redox potentials become main physical parameters of this design. The protein identity, flexibility, or dynamics are missing from this picture assigning universal charge-transport properties to all proteins. This paradigm is challenged by dynamical models of electron transfer showing that the hopping rate is constant within the crossover distance R*≃12 Å, followed with an exponential tunneling falloff at longer distances. In this view, energy chains for electron transport are best designed by placing redox cofactors near the crossover distance R*. Protein flexibility and dynamics affect the magnitude of the maximum hopping rate within the crossover radius. Protein charge transport is not driven by universal parameters anymore and protein identity matters.

The reported study was devoted to the investigation of viscoelastic behavior for solid and porous ultra-high-molecular-weight polyethylene (UHMWPE) under compression. The obtained experimental stress curves were interpreted using a two-term Prony series to represent the superposition of two coexisting activation processes corresponding to long molecular (~160 s) and short structural (~20 s) time scales, respectively, leading to good statistical correlation with the observations. In the case of porous polymer, the internal strain redistribution during relaxation was quantified using Digital Image Correlation (DIC) analysis. The strongly inhomogeneous deformation of the porous polymer was found not to affect the relaxation times. In order to generalize the results to three dimensions, X-ray tomography was used to examine the porous structure at the macro- and micro-scale levels. DIC analysis revealed positive correlation between the applied force and relative density. The apparent stiffness variation for UHMWPE foams with mixed open and closed cells was described using a newly proposed three-term expression. Furthermore, the in situ tensile loading and X-ray scattering study was applied for isotropic solid UHMWPE specimens to investigate their parameters of internal structure during orientation and stress relaxation process at another mode.

Mechanical recycling of solid plastic wastes on a small-scale level can be accomplished with the correct approaches. Thermoplastics are mostly considered for mechanical recycling because of their physical properties and ease of reprocessing. This paper reviews the mechanical reprocessing techniques of selected thermoplastics (polyethylene terephthalate and polyolefins) since they constitute a significant proportion of plastics used commercially. Furthermore, necessary considerations for effective operation of small-scale plants, including energy requirements of machinery and optimisation in order to improve efficiency and product quality, are discussed. A clearer understanding and addressing of the process-related challenges will lead to successful establishment and management of small-scale mechanical recycling facilities to benefit communities. Efficient small-scale mechanical reprocessing establishments have become essential in reducing the environmental impacts of solid plastic wastes and for energy conservation.

Here, a process for leaching vanadium from calcified roasting pellets (CPVC) of vanadium-titanium iron concentrate by a two-stage sulfuric acid cycle was proposed. When the silicon removal acid concentration of the pellet in the first stage was 1.5 mol/L, the solid-liquid ratio was 6: 1, the silicon removal acid concentration of the leaching solution was 3.0 mol/L, and the standing time was 48 h, the silica gel formation time was 23 h, the filtration time was 70 s, and the loss rates of vanadium and iron were 1.52% and 0.17%, respectively. When the acid concentration was 2 mol/L, at room temperature, using a leaching time of 28 days, and a solid-liquid ratio of 5: 1 in the second stage, the total leaching rates of vanadium and iron were 75.52% and 0.71%, respectively. The concentration of vanadium in the leaching solution reached 6.80 g/L, and vanadium was directly precipitated without extraction. After secondary roasting, the crushing strength of the pellets reached 2250 N, which met the requirement for blast furnace iron making. The Eh-pH diagrams of the V-Fe-H2O system at different temperatures were plotted. Thermodynamically, it was difficult to selectively leach vanadium and iron by changing the conventional acid leaching conditions. In addition, the pellets before and after leaching were analyzed. The grade of iron in the pellets increased slightly after leaching, and the main phases in the pellets remained as Fe2O3 and Fe9TiO15. The S in the sulfuric acid solution entered the leached pellets during the acid leaching reaction and was removed by the secondary roasting of the leached pellets.

Several reviews of inhibitors of topoisomerase II literature have been published covering research before 2018. Therefore, this review is focused primarily on more recent publications with relevant points from the earlier literature. Topoisomerase II is an established target for anticancer drugs, that are further subdivided into poisons and catalytic inhibitors. Whereas most of the topoisomerase II-based drugs in clinical use are mostly topoisomerase II poisons, their mechanism of action has posed severe concern due to DNA damaging potential, including development of multi drug resistance. As a result, we are beginning to see a gradual paradigm shift towards a non-DNA damaging agents, such as the lesser studied topoisomerase II catalytic inhibitors. In addition, this review will describe some novel selective catalytic topoisomerase II inhibitors. The ultimate goal is to bring researchers up to speed by curating and delineating new scaffolds as leads for optimization and development to new potent, safe and selective agents for the treatment of cancer.

Enterococcus faecalis is a bacterium that can develop a multidrug resistance profile associated with the community as well as nosocomial-acquired infections. Among the treatment options for these infections are aminoglycosides combined with bacterial cell wall inhibitors such as beta-lactams, since E. faecalis is intrinsically resistant to aminoglycosides. One of its most representative resistance mechanisms is the expression of aminoglycoside-modifying enzymes, such as the aminoglycoside phosphotransferase type IIIa of E. faecalis (EfAPH(3')-IIIa). This enzyme acts by phosphorylating aminoglycosides in an ATP-dependent reaction, modifying the 3' position of hydroxyl groups of these antibiotics. Considering this scenario, 3,092 natural products obtained from the ZINC22 database were analyzed to select molecules with the highest affinity for the nucleotide-binding pocket of EfAPH(3')-IIIa, which could be potential aminoglycoside adjuvants. The molecules that showed the best-score results obtained from ensemble docking-based virtual screening were ZINC000000952700 (BS-1), ZINC000014793040 (BS-2) and ZINC000015498603 (BS-3). The most promising results were for BS-2, a flavone derivative, due to its improved stability profile in molecular dynamics simulation (average values of RMSD of 0.23 nm, and Rg of 1.94 nm), binding free energy calculations (average ΔG total of -35.3 nm), as well as better toxicological profile (lower probability of hepatotoxicity, carcinogenic, immunotoxicity, mutagenicity, and cytotoxicity effects), compared to BS-1 and BS-3. These results allow us to propose that a flavone derivative may act as an adjuvant to aminoglycosides in the treatment of E. faecalis infections, acting as an inhibitor in the nucleotide-binding pocket of EfAPH(3')-IIIa.

Research for novel vaccine adjuvants remains a critical need to improve the immune responses to a recombinant vaccine antigen. Emulsion adjuvants such as AS03 and MF59, particularly in the area of Influenza vaccines, have shown antigen dose sparing and allowed reduced immunizations. It was previously demonstrated that these emulsion adjuvants can be formulated using a simpler, low shear process of self-emulsification. The role of alpha tocopherol as an immunomodulator in emulsion adjuvants is evident from the success of AS03 in the on-going covid-19 pandemic. Although, it was a challenge to formulate alpha tocopherol with a low shear process to get closer to the AS03 composition, the self-emulsified version referred as self-emulsifying adjuvant systems (SE-AS) showed comparable immune responses to AS03 when co-administered with a Quadrivalent influenza virus (QIV) vaccine. In this paper, we first optimized the SE-AS with alpha tocopherol referred to as SE-AS44 to allow sterile filtration. We compared the in vitro cytokine profile with self-emulsifying adjuvant 160 (SEA160), a squalene-only self-emulsified adjuvant with composition similar to MF59. We compared SE-AS44 and SEA160 co-administered with a recombinant cytomegalovirus (CMV) pentamer antigen, which is a less immunogenic antigen, in vivo to compare the antibody and T-cell responses, in different adjuvanted groups, in C57BL/6 mice.

So far, poly(L-lactic acid), PLLA, nanosheets proved to be promising for wound healing. Such biodegradable materials are easy-to-prepare, bio-friendly, cost-effective, simple to apply and were shown to protect burn wounds and facilitate their healing. At the same time, certain metal ions are known to be essential for wound healing, which is why this study was motivated by the idea of incorporating PLLA nanosheets with Zn2+ ion containing nanoparticles. Upon being applied on wound, such polymer nanosheets should release Zn2+ ions, which is expected to improve wound healing. The work thus focused on preparing PLLA nanosheets embedded with several kinds of Zn-containing nanoparticles, their characterization and ion-release behavior. ZnCl2 and ZnO nanoparticles were chosen as model particles with different solubility in water, both types showing similar ion release dynamics in liquid medium with pH around 7.4.

In the present study, the problem of the sulfuric acid recycling from spent copper plating solution was solved using a hybrid membrane technology, including diffusion dialysis and electrodialysis. A real solution from the production of copper-coated steel wire, containing 1.45 mol/L of sulfuric acid, 0.67 mol/L of ferrous sulfate and 0.176 mol/L of copper sulfate was processed. Diffusion dialysis with anion-exchange membranes was used to separate sulfuric acid and salts of heavy metals. Then purified dilute sulfuric acid was concentrated by electrodialysis. Energy consumption for sulfuric acid electrodialysis concentration at a current density of 400 A/m2 was 162 W·h/mol with current efficiency 16 %. After processing according to the hybrid membrane scheme, the solution contained 1.13 mol/L sulfuric acid, 0.077 mol/L ferrous sulfate and 0.022 mol/L copper sulfate. The resulting acid solution with a small amount of ferrous sulfate and copper sulfate met the established requirements for a copper plating bath solution and can be reused in production.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Starch is a widespread natural polymer used in healthcare applications due to its low cost and antibacterial properties. The use of starch in its many forms and its sometimes combination with metallic nanoparticles have all contributed to the advancement of biomaterials. However, few studies have been conducted on biocomposites composed of jackfruit starch and silver nanopar-ticles (AgNPs). As a result, this research aims to study the physicochemical, morphological, and cytotoxic features of a Brazilian jackfruit (Artocarpus heterophyllus) starch-based scaffold loaded with AgNPs. Gelatinization and chemical reduction were used to synthesize the scaffold and AgNPs, respectively. X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS), and Fourier transform infrared spectroscopy (FTIR) were utilized to explore the properties. The findings supported the development of anisotropic, stable, monodispersed AgNPs. The presence of AgNPs in the scaffold matrix was revealed by XRD and SEM-EDS. AgNPs were found to modify the crystallinity, roughness, and thermal stability of the scaffold while leaving its chemical and physical characteristics unchanged. Finally, the scaffolds did not show adverse effects on the L929 cells.

In contrast to the traditional fillers, clay, in particular, natural smectite clay represents an environmentally significant alternative to improve the properties of polymers. Compared to con-ventional nanofillers, smectite clay can effectively enhance the physical and mechanical properties of polymer nanocomposites with a relatively small amount of addition (< 5 wt%). The present study focuses on investigating the reinforcing efficiency of different amounts (up to 5 wt%) of a natural Brazilian smectite clay on the mechanical and thermal properties of poly(butylene terephthalate) (PBT) nanocomposites. Natural Brazilian clay modified by addition of quaternary salt and sodium carbonate (MBClay) was infused into the PBT polymer by melt extrusion, using a twin-screw extruder. It was found that the best properties for PBT were obtained at 3.7 wt% of modified BClay. Tensile strength at break exhibited an increase of about 60 %, flexural strength increased by 24 % and flexural modulus increased by 17 %. In addition, an increase in the crystallinity percentage of PBT/BClay nanocomposite was confirmed by DSC and XRD analysis, and a gain of about 45 % in HDT was successfully achieved due to incorporation of 3.7 wt% of MBClay.

Artic root is a well-known plant adaptogen with multipotential pharmacological properties. Thin-layer chromatography (TLC) – screening followed by diode-array high-performance liquid chromatography and nuclear magnetic resonance spectroscopy proved to be a reliable and convenient method for simultaneous determination of quality of various herbal raw materials and supplements. This combination allowed for comparing and differentiating arctic root samples as well as defining their authenticity. The study provided information on the chemical and biological properties of the seven chosen samples as well as qualitative and quantitative evaluation of the quality markers: rosavin, salidroside, and p-tyrosol. The absence of rosavin, salidroside, and p-tyrosol in three samples was detected using TLC-screening and confirmed by HPLC-DAD and NMR. The paper highlighted the importance of quality control and strict regulation for herbal medicine supplements and preparations.

Nanomedicine holds great potential to devise better drug delivery systems (DDSs). However, many reported nanomedicines still fall short of commercial requirements including specific targetability, scale-up manufacturing and safety. Cell/tissue based carriers, including cell membrane vehicle and exosome, are biocompatible and targeting platforms but usually suffered from low yields and unstable reproducibility. Here in this study, we proposed the concept and preparation of reconstituted lipid nanoparticles (rLNPs) to develop highly reproducible cell/tissue based lipid nanoparticles (LNPs) for drug delivery, which holds the potential as a versatile drug delivery platform. The whole lipids of cell or tissue were firstly extracted and then prepared into rLNPs using solvent diffusion method. In this way, the preparation of ultra-small (~20 nm) rLNPs can be easily applied to both cell (mouse breast cancer cell line, 4T1) and tissue (mouse liver tissue). Our results demonstrated that mouse liver tissue derived rLNPs can be further labeled/modified with imaging, targeting or other functional moieties. Furthermore, rLNPs were highly biocompatible and capable of loading different drugs including doxorubicin hydrochloride (Dox) and curcumin (Cur). Most importantly, Dox loaded rLNPs (rLNPs/Dox) showed preferable in vitro and in vivo anticancer performance. Therefore, rLNPs might be a versatile drug delivery platform for future application in the treatment of a variety of diseases.

Transmembrane transport of small organic and inorganic molecules is one of the cornerstones of cellular metabolism. Among transmembrane transporters, solute carrier (SLC) proteins form the largest, albeit very diverse, superfamily with over 400 members. It has been early on recognized that xenobiotics can directly interact with SLCs and that this interaction can fundamentally determine their efficacy, including bioavailability and intertissue distribution. Apart from the well-established prodrug strategy, the chemical ligation of transporter substrates to nanoparticles of various chemical composition has recently been used as a means to enhance their targeting or absorption. In this review, we summarize efforts in drug design exploiting interactions with specific SLC transporters to optimize their therapeutic effects. Furthermore, we describe current and future challenges as well as new directions for the advanced development of therapeutics that target SLC transporters.

Plant secondary metabolites are organic compounds (alkaloids, flavonoids, phenolics, tannins, anthraquinones, saponins, steroids, lignins, terpenes) produced by plant for self-defense during growth and development in order to protect them from harmful agents. As population is increasing and quality of life is reducing couple with outbreak of some diseases that are posing threat on the economy, a lot of medicinal plants have attracted interest of researchers because of the usefulness of these metabolites in pharmaceuticals, food and cosmetic industries. In this review, the pharmacological activities of some medicinal plants that are rich in secondary metabolites were studied, means of identifying and quantifying using spectrophotometry and chromatography techniques were also discussed. However, this will assist to reduce the uses and dependent on the synthetic drug and the onset of the age related diseases.

Hot spring is a hot water that is naturally occurring on the surface from the underground and typically heated by subterranean volcanic activity and local underground geothermal gradient. There are four main hot springs in Rwanda such as: Kalisimbi, Bugarama, Kinigi and Nyamyumba former name Gisenyi hot springs. It is often believed that soaking in hot springs is a great way which naturally detox human skin. This research focused on the geochemical analysis of Nyamyumba hot springs located near the fresh water of Lake Kivu for the purpose of understanding its healing capacity and safety. Nyamyumba hot springs are located in the western branch of the East African Rift System and they are located near Virunga volcanic complex, explaining the rising and heating mechanism of water. The concentrations of Sulfate, Iron, Ammonia, Alkalinity, Silica, Phosphate, Salinity, Alkalinity, and Conductivity using standard procedures were measured. The results showed that hot spring water has higher concentrations of chemicals compared to Lake Kivu water and the geochemistry of these hot springs maybe associated with rock dissolution by hot water. The measured parameters were compared with World Health Organization (WHO) standards for recreational waters and it has been identified that Nyamyumba hot springs are safe to use in swimming and therapeutic activities.

Maxwell's electric equation and Schrödinger quantum equation are used to find useful expressions for the probability of electrons existence and the electrons transport. The first expression which uses special relatively also shows that the probability of the electrons existence is higher for lower energy states compared to higher energy states where the probability is low. This means that electrons transport takes place from higher energy states to lower states. This conforms to the laws of chemistry where the atom tends to be stable by forcing electrons to occupy lower energy states. The second expression used the momentum velocity relation instead of special relatively. This expression shows also electrons transport from higher to lower states. It also shows that the probability of the electrons existence is higher for lower electrons density regions and lower for higher electrons density regions. This means that the electrons transport is from higher density regions to lower density regions. This conforms to the diffusion law.

Anion exchange of the halides, Br and I, is demonstrated through the direct mixing of two pure perovskite quantum dot solutions, CsPbBr3 and CsPbI3, and is shown to be both facile and result in a completely alloyed single phase mixed halide perovskite. Anion exchange is also observed in an interlayer printing method utilizing the pure, unalloyed perovskite solutions and a commercial inkjet printer. The halide exchange was confirmed by optical absorption spectroscopy, photoluminescent spectroscopy, X-ray diffraction, and X-ray photoemission spectroscopy characterization, and indicates that alloying is thermodynamically favorable, while the formation of a clustered alloy is not favored. Additionally, a surface-to-bulk photoemission core level transition is observed for the Cs 4d photoemission feature which indicates the electronic structure of the surface is different from the bulk. Time resolved photoluminescence spectroscopy indicates the presence of multiple excitonic decay features which is argued to originate from states residing at surface and bulk environments.

Polyhedral oligomeric silsesquioxane (POSS) is a suitable nanoscale reinforcement for thermosetting polymers, such as epoxy resin systems in order to modify its mechanical, thermal, and chemical properties. The inclusion of POSS in the epoxy resin at higher loading (greater than 1 wt.%), however, introduces the ductility during the fracture behavior of these nanocomposites. Consequently, the J-integral is used to quantify the fracture behavior of these materials and characterize the crack growth resistance curve against stable crack growth. A range of nanocomposites is prepared by adding 0.5, 1, 3, 5, and 8 wt.% of glycidyl POSS into DGEBF epoxy resin cured with an amine-based curing agent. From the fracture toughness experiment the load-displacement result confirms that when the POSS reinforcement is greater than 1 wt.%, the fracture behavior of the nanocomposite changes from brittle to ductile. For both brittle and ductile nanocomposites, the addition of POSS molecules improves the crack initiation toughness. The development of POSS–POSS compliant domains are reported previously, is attributed for this change in the failure behavior. The fractured images of POSS–epoxy nanocomposites, obtained using scanning electron microscopy, show that the increase in fracture resistance at higher values of POSS loading occurs due to the extensive shear yielding. Meanwhile, the increased fracture toughness at lower values of POSS loading occurs due to crack pinning and crack deflection.

Electron beam treatment of ZnS:Cu,Br (Cu activator content 0…0.6%wt.) radioluminescent phosphors as well as charge mixture with the electron energy 900 keV and absorbed dose of 600 kGy resulted in a enhancement of brightness up to 80%. The increased brightness is due to increase of content of wurtzite phase relative to sphalerite one with formation of wurtzite/sphalerite nanocomposite structure. Transformation of crystal structure is accompanied with corresponding change in content of active surface centers characteristic for sphalerite and wurtzite phases. A model describing surface centers of ZnS:Cu,Br radioluminescent phosphor is suggested.

In this paper, we present the interaction results of 1,2-dibromo-3-isothiocyanatopropane with some pyrazoles and cytisine and salsoline alkaloids. It has been shown that the reaction results in the one-step and rather mild method for the preparation of the corresponding 1,3-thiazoline bromomethyl derivatives. The yield of this reaction is affected by the presence of a base and the order in which the reagents are added. Molecular docking of the synthesized 1,3-thiazoline derivatives for putative antibacterial activity has been carried out using the penicillin-binding target protein (PBP4) of the bacteria E. coli “Homo sapiens” and S. aureus “Homo sapiens” as an example. Molecular docking shows that the compounds have insignificant binding energies at the level of selected reference drugs (Cephalotin and Chloramphenicol). The presence of natural alkaloids in the structure of thiazoline derivatives somewhat increases the affinity of these substrates for target proteins selected.

Read-Across Structure-Activity Relationship (RASAR) is an emerging cheminformatic approach that combines the usefulness of a QSAR model and similarity-based Read-Across predictions. In this work, we have generated a simple, interpretable, and transferable quantitative-RASAR (q-RASAR) model which can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials. The data set involves 29 TiO2-based nanomaterials which contain specific amounts of noble metal precursors in the form of Ag, Au, Pd, and Pt. The data set was rationally divided into training and test sets and the Read-Across-based predictions for the test set were generated using the tool Read-Across-v4.1 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. The hyperparameters were optimized based on the training set data and using this optimized setting, the Read-Across-based predictions for the test set were obtained. The optimized hyperparameters and the similarity approach, which yields the best predictions, were used to calculate the similarity and error-based RASAR descriptors using the tool RASAR-Desc-Calc-v2.0 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. These RASAR descriptors were then clubbed with the physicochemical descriptors and were subjected to features selection using the tool Best Subset Selection v2.1 available from https://dtclab.webs.com/software-tools. The final set of selected descriptors was used to develop multiple linear regression based q-RASAR models, which were validated using stringent criteria as per the OECD guidelines. Finally, a random forest model was also developed with the selected descriptors. The final machine learning model can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials superseding previously reported models in the prediction quality.

A series of cysteine-based perfluoroaromatic (hexafluorobenzene (I) and decafluorobiphenyl (II) were synthesized and established as a chemoselective and available core to simple or more complex systems since small molecules to biomolecules with interesting properties. As proof of concept of the potential application of perfluorinated derivatives as non-cleavable linkers, some antibody-perfluorinated conjugates were prepared via thiol, demonstrating that the bioconjugation process doesn’t affect to the macromolecular entity. Besides, some molecular properties of synthesized compounds are evaluated using a combination of spectroscopic characterization (FT-IR and 19F-NMR chemical shifts) and theoretical calculations. Moreover, molecular Docking was also developed to predict cysteine-based hexafluorobenzene and decafluorobiphenyl derivatives’ affinity against topoisomerase Il and cyclooxygenase 2 (COX-2). The results suggested that mainly cysteine-based decafluorobiphenyl derivatives could be potential topoisomerase II α and COX-2 inhibitors, becoming potential anticancer agents and candidates for anti-inflammatory treatment.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

Rice is considered as the most important crop for most of the world population. Utilization of seaweed as bio-stimulant can be an alternative way to enhance rice plant growth and productivity, as well as a strategic move to reduce the use of inorganic fertilizer that is harmful to the environment. Seaweed and its derivative products have been widely used as bio-stimulant in the agricultural industry because of their potential use in increasing plant growth and productivity. Auxins, gibberellins, and cytokinin are some of growth regulators found in seaweed extract, as well as macro and micronutrients required for plant growth and development. Several studies have found that seaweed extract has a variety of favorable effects as a plant growth promoter, including early seed germination and establishment, improved nutritional quality, increased yield and crop performance, and increased tolerance to environmental stress. The purpose of this paper is to give a comprehensive overview of the impacts of several seaweed species on seed germination, crop development and production, enhancement of rice plants (Oryza sativa) nutritional quality and the modes of action of seaweed extract includes the chemical components that might be causing plant physiological changes.

This article has been studied the synthesis of a new derivative of the known alkaloid cytisine contained in the seeds of plants of Cytisus laburnum L. and Thermopsis lanceolata R.Br., both of the Lugiminosae family. The new compound has been obtained from two biologically active compounds such as isoxazole and cytisine. It has been demonstrated that the reaction led to the single-stage method under very mild conditions to obtain some 4-[(3,5-dimethyl-1,2-oxazole-4-yl)sulfonyl]amides. This class of compounds is promising to obtain the new biologically active compounds. This article has examined in detail a structure with using the 1H and 13C NMR and two-dimensional NMR spectroscopy of COSY (1H-1H), HMQC (1H-13C) and NMVS (1H-13C). As a result, the homo- and heteronuclear spin-spin couplings should be established. The X-ray diffraction analysis has determined the spatial structure of a new derivative based on cytisine alkaloid. Thus, its hemorheological activity has been studied.

The abundant use of lithium-ion batteries (LIBs) in a wide variety of electric devices and vehicles will generate a large number of depleted batteries, which contain several valuable metals such as Li, Co, Mn, and Ni present in the structure of the cathode material (LiMO2). The present work investigates chemical, technological, and environmental aspects in the treatment of such wastes, development of a methodology for the extraction of lithium, cobalt, nickel, manganese, and graphite by a carbochlorination pyrometallurgical process. Mixtures of cathode and anode materials (called black mass, mixed oxides of Li, Co, Ni, Mn, and graphite) from different LIBs, carbon black (as reducing agent), and CaCl2 (as chlorinating agent) were used. Non-isothermal thermogravimetric tests up to 850°C and isothermal tests at 700°C of the mixtures in an inert atmosphere were carried out. It was experimentally observed that the LiMO2-C-CaCl2 reaction takes place at 700°C. LiCl, Ni, and Co were obtained as final products, and to a lesser extent, CoO, NiO, and MnO2. CaCO3 was also obtained as a by-product. The obtained results show that carbochlorination is an efficient and effective alternative route for the extraction and recovery of metals from different LIBs, focused on the sustainability and circular economy

A series of N-acyl derivatives of anabasine and cytisine were prepared to discover novel natural product-based medicinal agents. All synthesized compounds were tested for antimicrobial, antifungal, antiviral and analgesic activity. The most pronounced antibacterial activity was shown by the compounds with isoxazole fragments, while adamantane derivatives showed the greatest antiviral effect. It was found that the majority of anabasine derivatives showed significant analgesic activity reducing the pain response of animals to the irritating effect of acetic acid. The presence of a high level of antimicrobial and antiviral activity in newly synthesized compounds makes it possible to consider them promising for further study of their pharmacological properties.

Iron oxide nanozymes are a form of nanomaterial with both superparamagnetic and enzyme-mimicking properties. Given the multifunctional nature of iron oxide nanozymes, it is attractive for creating iron oxide hybrid nanozymes through biomolecular modifications to imbue with auxillary properties. Such iron oxide hybrid nanozymes can be useful for rapid and cost-effective analysis of circulating tumor nucleic acids (ctNAs) in patient liquid biopsies during minimal residual disease (MRD) monitoring of cancer recurrence. Herein, the use of streptavidin-modified iron oxide hybrid nanozymes is reported for magnetic enrichment and bioelectrocatalytic sensing of three prostate cancer (PCa) ctRNA biomarkers with high detection specificity and sensitivity (10 copies) over an ultrabroad dynamic range (five orders of magnitude). Furthermore, the feasibility of ctRNA analysis for pre- and post-cancer treatment MRD monitoring is demonstrated using PCa urinary liquid biopsy samples.

Spider silk has excellent strength and elasticity in natural, researchers have been working for decades try to achieve natural spider silk outstanding mechanical properties using recombinant spider silk protein (spidroin) through artificial spinning. In this work, we chose wet spinning method to explore the relationship between concentration of coagulation bath and fiber performance. It was found that the concentration of methanol has important effect on fiber continuity, diameter and mechanical properties. Lower concentration favors spinning continuous thinner, fibers with high strain. Secondary stretching benefits spinning silk fibers with stable mechanical properties, and thermal stability. Through applying different methanol concentration and additional stretching, we obtained silk fibers with Young’s modulus of 3.052± 2.626 GPa, stress of 25.3944 ± 17.48 MPa, and strain of 140 ± 95.4%.

The preparation of sulfur-single walled carbon nanohorns active material via a simple and sustainable evaporation method for application as cathode in lithium-sulfur batteries is reported. We show that the synthesis process enables the infiltration of elemental sulfur within the carbon nanohorns thus obtaining a morphology responsible for the ameliorating of the shuttle effect. The sulfur-carbon composite is characterized in terms of structure, morphology, and composition through x-ray diffraction, transmission electron microscopy, and thermogravimetric analyses. From the electrochemical point of view, cyclic voltammetry, rate capability, and galvanostatic cycling tests are performed employing a solution of bis(trifluoromethane)sulfonimide lithium salt and lithium nitrate in a mixture of 1,2-dimethoxyethane and 1,3-dioxolane in order to evaluate the electrode design applicability within lithium-sulfur cells. In this respect, further insights are provided by the estimation of the lithium-ion diffusion coefficient through the Randles-Sevcik equation, and by electrochemical impedance spectroscopy. The obtained results reveal a remarkable cycle life lasting around 800 cycles with a stable capacity of 520 mA h g-1 for the first 400 cycles at C/4, while reaching a value around 300 mA h g-1 at the 750th cycle. These results suggest sulfur-carbon nanohorns active material as a potential candidate for the next-generation battery technology.

Ochna kibbiensis (Family: Ochnaceae) has been employed in ethnomedicine for the treatment of malaria, and inflammation among others. The aim of this study was to isolate and characterize prophylactic antimalarial agents from the leaves of O. kibbiensis against Plasmodium berghei, in vivo and in silico. The median lethal dose (LD50) of the methanol extract and its fractions (n-hexane, dichloromethane, ethylacetate and n-butanol) was determined according to Lorke’s method while the antimalarial effect of the extract and its fractions was investigated according to the method described by Peters prophylactic test using Chloroquine-sensitive Plasmodium berghei (NK65). All the extract/fractions exhibited LD50 values ≥ 5000 mg/kg with the exception of the n-butanol fraction (1702.94 mg/kg) which indicate that the plant is non-toxic. Dichloromethane fraction exhibited significant (p&lt;0.05) and dose-dependent prophylactic effect with 47.62, 85.12 and 100.0 % prophylaxis (at 500, 250 &amp; 125 mg/kg) while the least effect was observed by the n-butanol fraction with percentage prophylaxis of 64.29 and 76.19, respectively; the standard drug, pyrimethamine had 95.24 % prophylaxis. Based on the result obtained, dichloromethane fraction of O. kibbiensis was subjected to chromatographic purification which led to the isolation of a mixture of two compounds identified as stigmasterol and β-sitosterol by analysis of the NMR spectral data and comparison with existing literature; the compounds exhibited good binding affinities (- 5.129 and - 4.889 kcal/mol) against pfLDH and favorable ADMET profile. In conclusion, the leaf of O. kibbiensis have demonstrated a significant prophylactic antimalarial activity and the two known steroids (stigmasterol and β-sitosterol) isolated from the dichloromethane fraction for the first time.

Hyperaccumulator plant species growing on metal-rich soils can accumulate high quantity of metals and metalloids in aerial tissues and several proteomic studies on the molecular mechanisms at the basis of metals resistance and hyperaccumulation have been published. Hyperaccumulator are also at the basis of phytoremediation strategy to remove more efficiently metals from polluted soils or water. Arabidopsis halleri and Noccea caerulescens are both hyperaccumulators of metals and nano-metals. In this study it was assessed the change in some proteins in A. halleri and N. caer-ulescens after the growth in soil with cadmium and zinc, provided as sulphate salts (CdSO4 and ZnSO4) or sulfide quantum dots (CdS QDs and ZnS QDs). The protein extracts obtained from plants after 30 days of growth were analyzed by 2D-gel electrophoresis (2D SDS-PAGE) and identified by MALDI-TOF/TOF mass spectrometry. A bioinformatics analysis was carried out on quantitative protein differences between control and treated plants. In total, 43 proteins resulted significatively modulated in A. halleri, while 61 resulted modulated in N. caerulescens. Though these two plants are hyperaccumulator of both metals and nano-metals, at protein levels the mechanisms involved do not proceed in the same way but at the end bring to a similar physiological result.

The unique properties and morphology of liquid marbles (LMs) make them potentially useful for various applications. Non-edible hydrophobic organic polymer particles are widely used to prepare LMs. It is necessary to increase the variety of LM particles to extend their use into food and pharmaceuticals. Herein, we focus on hydrophobically modified gelatin (HMG) as a base material for the particles. The surface tension of HMG decreased as the length of alkyl chains incorporated into the gelatin and the degree of substitution (DS) of the alkyl chains increased. HMG with a surface tension of less than 37.5 mN/m (determined using equations based on the Young-Dupré equation and Kaelble-Uy theory) successfully formed LMs of water. The minimum surface tension of a liquid in which it was possible to form LMs using HMG particles was approximately 53 mN/m. We also showed that the liquid-over-solid spreading coefficient S_(L/S) is a potential new factor for predicting if particles can form LMs. The HMG particles and the new system for predicting LM formation could expand the use of LMs in food and pharmaceuticals.

Mass transfer is often the rate determining step for solid-liquid chemical reactions. Decrease of the concentration boundary layer thickness is essential to intensify the chemical reaction. Because the concentration boundary layer exists in the velocity boundary layer, force imposition in the concentration boundary layer by superimposing an electrical current and a magnetic field was proposed. Through, flow can be directly excited in the concentration boundary layer. The previous result indicates that by superimposing a DC current and a gradient magnetic field, the development of the concentration boundary layer was suppressed, because of a macro-scale flow excitation in the whole vessel. And by superimposing the gradient magnetic field with a modulate current, the development of the concentration boundary layer was further suppressed. This is because of the macro-scale flow enhancement and the excitation of a micro-scale flow near the solid-liquid interface. However, the mechanism for the micro-scale flow excitation has not been clarified. To clarify this, a uniform magnetic field was superimposed with the DC current or the modulate current. By this means, only the micro-scale flow was excited near the anode surface. The results found that the non-unform electromagnetic force distribution is the main reason for the micro-scale flow excitation.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

Organophosphorus nerve agents are amongst the most toxic chemicals known to human beings. 9 They interfere with the central nervous system, resulting in continuous muscle contractions, 10 paralysis and even death. Prohibition by many countries around the world cannot disguise the 11 remaining presence of nerve agents in stockpile storage and governmental deployment, 12 highlighting the dire need for an efficient catalyst to degrade and detoxify nerve agents by 13 hydrolysis. Metal-organic frameworks (MOFs) have raised a few eyebrows for their permanent 14 porosity, precise tunability, and lasting stability. Modern Reticular Chemistry fosters the design and 15 synthesis of well-defined crystalline MOFs with open Lewis acidic metal sites that can catalytically 16 hydrolyze nerve agents both in aqueous solution and in solid state systems, unveiling unparalleled 17 potential for MOF-based personal protection gears. In this review, a summary of the representative 18 catalytically active MOFs in nerve agent hydrolysis is discussed. MOFs are categorized by their 19 reticular structure, emphasizing the capability and mechanistic insights of each single MOF in nerve 20 agent hydrolysis. The author’s perspective on the current challenges and future directions of MOF- 21 based catalysts in real-world protection applications is also provided, which hopefully could shed some 22 light on the future development of commercially available MOF protection suits.

Uncontrollable Zn dendrite formations and parasitic side reactions on Zn electrodes induce poor cycling stability and safety issues, preventing the large-scale commercialization of Zn-ion batteries. Herein, to achieve uniform Zn deposition and suppress side reactions, an electrospun ferroelectric poly(vinylidene fluoride-co-trifluoroethylene) copolymer, a [P(VDF-TrFE)] nanofiber layer, is introduced as an artificial solid-electrolyte interface on a Cu substrate acting as a current collector. The aligned molecular structure of β-P(VDF-TrFE) can effectively suppress localized current density on the Cu surface, lead to uniform Zn deposition, and suppress side reactions by preventing direct contact between electrodes and aqueous electrolytes. The half-cell configuration formed by the newly fabricated electrode can achieve an average coulombic efficiency of 99.2% over 300 cycles without short circuiting at a current density of 1 mA cm-2 and areal capacity of 1 mAh cm-2. Stable cycling stability is also maintained for 200 cycles at a current density of 0.5 A g-1 in a full-cell test using MnO2 as a cathode.

Catalyst with high catalytic activity and good stability are desirable in the electrocatalytic oxidation of glucose. Herein, Pt concave nanocubes with high-index facets (HIFs) supported by carbon black (Pt CNC/CB) are prepared through a hydrothermal method. The experimental results demonstrate that the peak current densities in different potential regions on the Pt CNC/CB anode are 0.22, 0.20, and 0.60 mA cm−2, respectively. The glucose oxidation reaction shows superior performances in basic and neutral conditions than in acid conditions. Better stability is achieved by Pt CNC/CB than Pt concave nanocubes (Pt CNCs). Abundant surface defects with low-coordinated atom numbers, such as the steps, kinks, and edges, are served as active sites in the electrocatalytic oxidation of glucose. With the addition of carbon black, the catalytic activity can be improved by facilitating the full exposure of the active surface defects on the HIFs of Pt CNCs. Moreover, to address the aggregation of Pt CNCs, caused by the high surface energy of HIFs, the introduction of carbon material is an effective way to preserve the HIFs, and thus enhance the stability of the catalyst. Hence, the prepared Pt CNC/CB electrocatalyst has great potential to be applied in the electrooxidation of glucose.

Transparent and high-hardness materials have become the object of wide interest. Most notably, it concerns technical glasses and crystals. A notable example is a sapphire – one of the most rigid materials having impressive mechanical stability and good optical properties. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on c-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for modification inscription and various etchants (Hydrofloridic acid, Sodium Hydroxide, Potassium Hydroxide and Sulphuric and Phosphoric acid mixture) comparison. We show that regular SLE etchants such as Hydrofluoric acid or Potassium Hydroxide are unsuitable materials for selective sapphire laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270°C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. Finally, a protocol for advanced sapphire structure formation and a few exemplary structures are presented.

This study aims to develop an in-situ field repair approach, special for aircraft composite structures, to enhance the interlaminar toughness of plain woven composites (PWCs) by adding multi-walled carbon nanotubes (MWCNTs). MWCNTs are dispersed at each interface between prepreg layers by means of solvent spraying with the density is 1.58 g/m2. And then, the layers are stacked with the predefined sequence and cured at 120℃ and 1 bar pressure using the heat repairing instrument. Moreover, double cantilever beam (DCB) standard test is used to investigate the interlaminar toughening effect due to the MWCNTs. For comparison, original samples are also prepared, the results indicate that the introduction of MWCNTs can favorably enhance the interlaminar toughness of PWCs at field repair approach and the Mode I fracture energy release rate GIC increases by 102.92%. Based on finite element method (FEM) of continuum damage mechanics, the original and MWCNTs toughening specimen under DCB Mode I fracture are modeled and analyzed. The simulation and experiment are in good agreement. Finally, the toughening mechanism of MWCNTs is explored by scanning electron microscope (SEM), it is founded that a large amount of Fiber-matrix (F-M) interface debonding and matrix cracking of mountain shape are the major modes of fracture accompanied with few fiber breakage and matrix peeling off for the MWCNTs toughening specimens.

Binary mixtures of surfactants build a binary mixed micelle in which the ratio of surfactants usually differs from the initial ratio of surfactants in their binary mixture. The thermodynamic stabilization of the binary mixed micellar pseudophase about the hypothetical ideal state (intermolecular interactions between the different particles and the conformational states of the particles are identical to those of monocomponent states) is described by the molar excess Gibbs free energy (gE). The dependence of gE on the molar fraction of surfactant i (xi) from the binary mixed micelle can be described by a symmetric function (symmetry is described to the line parallel to the y-axis and passes through xi = 0.5) or by an asymmetric function. Theoretical analysis (canonical partition function, conformational analysis) examines how the presence of different polar functional groups, some of which are sterically shielded from the steroid skeleton of bile salt (surfactant), affect the symmetry of the function gE of the binary mixed micelle of the cholic acid anion (bile salt) and classical cationic surfactant (hydrophobic tail and polar head). Suppose the steroid skeleton of the bile salt contains non-sterically shielded polar groups (or the temperature is relatively high). In that case, gE is a symmetric function. At the same time, if the steroid skeleton also contains sterically shielded polar groups, then the gE function is asymmetric.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

The COVID-19 pandemic has highlighted the importance and urgent need of rapid and accurate diagnostic tests for detection and screening of this infection. In our proposal, a biosensor based on the ELISA immunoassay was developed for monitoring antibodies against SARS-CoV-2 in human serum samples. The SARS-CoV-2 nucleocapsid protein (N-protein) was selected as a specific receptor for the detection of SARS-CoV-2 nucleocapsid immunoglobulin G. Thus, the N-protein was immobilized on surface of screen-printed carbon electrode (SPCE) modified with carboxylated graphene (CG). The IgG-SARS-CoV-2 nucleocapsid concentration was quantified using a secondary antibody labelled with horseradish peroxidase (HRP) (anti-IgG-HRP) catalyzed by 3,3’,5,5’-tetramethylbenzidine (TMB) mediator by chronoamperometry. A linear response was obtained in the range of 1:1000-1:200 v/v in phosphate buffer solution (PBS) and the limit of detection calculated was of 1:4947 v/v. The chronoamperometric method showed electrical signals directly proportional to antibody concentrations due to Ag-Ab specific and stable binding reaction.

This research program investigated the effects of layer thickness (50 and 100 microns) on the microstructure and mechanical properties of electron beam powder bed fusion (EBPBF) additive manufacturing of Inconel 625 alloy. The as-built 50 and 100 micron layer thickness components were also heat treated at temperatures above 1100 oC, which produced a recrystallized grain structure containing annealing twins in the 50 micron layer thickness components, and a duplex grain structure consisting of islands of very small equiaxed grains dispersed in a recrystallized, large-grain structure containing annealing twins. The heat treated component microstructures and mechanical properties were compared with the as-built components in both the build direction (vertical) and perpendicular (horizontal) to the build direction. Vickers microindentation hardness (HV) values for the vertical and horizontal geometries averaged 227 and 220 for the as-built 50 and 100 micron layer components, and 185 and 282 for the corresponding heat treated components. The yield stress values were 387 MPa and 365 MPa for the as-built layer horizontal and vertical 50 micron layer geometries, and 330 MPa and 340 MPa for the as-built 100 micron layer components. For the heat treated 50 micron components, the yield stress values were 340 and 321 MPa for the horizontal and vertical geometries, and 581 and 489 MPa for the 100 micron layer components, respectively. The elongation for the 100 micron layer as-built horizontal components was 28% in contrast to 65% for the corresponding 100 micron heat treated layer components, an increase of 132% for the duplex grain structure. However, the coarse grains containing annealing twins and the equiaxed small grain islands in the duplex structure for the heat treated components contained continuous carbides in the grain boundaries, and this may indicate sensitization and a reduction in corrosion resistance. These findings point to the potential mechanical property advantage for heat treatment of Inconel 625 alloy 100 micron layer thickness components fabricated by EBPBF.

Tungsten fibre-reinforced tungsten composites (Wf/W) have been in development to overcome the inherent brittleness of tungsten as one of the most promising candidate for the first wall and divertor armour material in a future fusion power plant. As the development of Wf/W continues, the fracture toughness of the composite is one of the main design drivers. In this contribution the efforts on size upscaling of Wf/W based on Chemical Vapour Deposition (CVD) is shown together with fracture mechanical tests of two different size samples of Wf/W produced by CVD. Three-point bending tests according to ASTM E399 for brittle materials were used to get a first estimation of the toughness. A provisional fracture toughness value of up to 346MPam1/2 was calculated for the as-fabricated material. As the material does not show a brittle fracture in the as-fabricated state, the J-Integral approach based on the ASTM E1820 was additionally applied for this state. A maximum value of the J-integral of 41kJ/m2 (134,8MPam1/2) was determined for the largest samples. Post mortem investigations were employed to detail the active mechanisms and crack propagation.

Controlling and understanding Cu-catalyzed homocoupling reaction is crucial to prompt the development of efficient Cu-catalyzed cross-coupling reactions. The presence of a coordinating base (hydroxide, methoxide) enables the B-to-Cu(II) transmetalation from aryl boronic acid to CuIICl2 in methanol, through formation of a mixed Cu-(μ-OH)-B intermediates. A second B-to-Cu transmetalation to form bis-aryl Cu(II) complexes is disfavored. Instead, organocopper(II) dimers undergo a coupled transmetalation-electron-transfer (TET) allowing the formation of a bis-organocopper(III) complexes readily promoting reductive elimination. Based on this mechanism some guidelines are suggested to control the undesired formation of homocoupling product in Cu-catalyzed cross-coupling reactions.

Silver iodide (AgI) is a system prototype allowing the flow of ions through its structure and has a phase transition at 420 K, characterized by an abrupt change in conductivity and a high ionic conductivity. Introducing low concentrations of graphite (C) into the AgI structure produces a new material with a mixed conductivity (ionic and electronic) which increases with increasing temperature. The experimental results of the logarithm of the ionic conductivity as a function of the inverse of temperature for the (AgI)x–C(1−x) system for low carbon concentrations 0.97 ≤ x ≤ 0.99 were well fitted using a phenomenological model with a probability distribution for the charge carriers based on the carrier density

The minimum requirement for uncertainty estimation is to use only intermediate precision (R_w), especially for measurands lacking a reference measurement system such as thyroid functions tests (TFT). In this study, measurement uncertainty (MU) for TSH and FT4 from long-term internal quality control (IQC) data was estimated while reference change values (RCV) were calculated from estimated MU. Furthermore, intermediate precision (R_w) was used to establish appropriate risk-based QC frequency. Twenty fore months of third party IQC data were collected retrospectively, on the Abbott ARCHITECT i1000sr analyzer from INSTITUT PASTEUR OF MSILA laboratory, ALGERIA. The MU, RCV and sigma-metric were estimated simply from the intermediate precision (R_w), while a nomogram relating sigma performance to run size was used to establish QC frequency. The MU for the TSH and FT4 was 12% and 8% respectively. The U _one-sided for the TSH and FT4 was 10%, 6.6% respectively. MU and U _one-sided of TSH and FT4 met quality requirements for permissible uncertainty (pU %) and allowable total error (ATE %). When monitoring thyroid replacement therapy, an upward minimum change (RCV) of 54% and 22% or a downward of 35% and 18% in serum TSH and FT4 respectively, would be considered significant. Optimal QC strategy for serum TSH was selected to run 4 QC materials every 190 patients sample and to use a multi-rule (1_3s/2_2s/R_4s/4_1s). Our results suggest that MU estimation from long-term IQC alone may be acceptable for TFT to assist physician in results interpretation and to establish appropriate QC frequency.

A series of novel indole Schiff base derivatives (2a–2t) containing a 1,3,4-thiadiazole scaffold modified with a thioether group were synthesized, and their structures were confirmed using FT-IR, ¹H NMR, ¹³C NMR, andHR-MS. In addition, the antifungal activity of synthesized indole derivatives was investigated against Fusarium graminearum (F. graminearum), Fusarium oxysporum (F. oxysporum), Fusarium moniliforme (F. moniliforme), Curvularia lunata (C. lunata), and Phytophthora parasitica var. nicotiana (P. p. var. nicotianae) using the mycelium growth rate method. Among the synthesized indole derivatives, compound 2j showed the highest inhibition rates of 100%, 95.7%, 89%, and 76.5% at a concentration of 500 μg/mL against F. graminearum, F. oxysporum, F. moniliforme, and P. p. var. nicotianae, respectively. Similarly, compounds 2j and 2q exhibited higher inhibition rates of 81.9% and 83.7% at a concentration of 500 μg/mL against C. lunata. In addition, compound 2j has been recognized as a potential compound for further investigation in the field of fungicides.

Modern technologies for recycling electronic waste (e-waste) impose high economic efficiency and environmental safety requirements. Among existing technologies, hydrometallurgy is considered the most promising technology for e-waste recycling. Increasing attention to the chlorination method is associated with the complex recycling of low-grade ores containing noble metals and secondary polymetallic raw materials. In this paper, we propose a new scheme for leaching metals from computer printed circuits (PCBs) pre-crushed in a disintegrator: the processes of chlorine production and hydrochlorination are implemented in one reactor under the action of alternating current (AC) of industrial frequency (50 Hz). It was found that complete leaching of gold is achieved from fine fractions of raw materials containing 0.03% and 0.01% of the gold at an experiment duration of 2 hours, a current density of 0.66 A·cm-2, and a solid/liquid ratio of 8.6 g·L-1. Under the same conditions of the electrochemical leaching process from the fraction of raw material with a gold content of 0.08%, the degree of metal leaching is 80.5%. At the same time, with an increase in the copper content in the raw material from 1.40% to 6.13%, an increase in the degree of its leaching from 84.6% to 95.2%, respectively, is observed. These results will serve as a foundation for developing a complex technology for recovering valuable metals from PCBs.

This publication highlights the effect of mechanochemical treatment in a high-speed thermoki-netic mixer as an alternative for recycling ground tire rubber (GTR). The GTR initially has an 80% gelled fraction and presented up to 50% gel fraction in the most intensive condition (5145 rpm, s2). Processing at the lowest speed (2564 rpm, s1) resulted in greater selectivity concerning the mechanochemical treatment (K~1). In the most intense processing condition (10 min. at s2), more significant degradation was observed via random scission with a reduction of the glass transition temperature, Tg (11ºC), an increase of the soluble polymer fraction, and a more signif-icant reduction in crosslink density. The artificial neural network could describe and correlate the thermal degradation profile and processing conditions with the physicochemical characteris-tics of the GTR. The approach presented here represents an alternative for mechanochemical treatment since it can reduce the crosslink density with selectivity and in short times (1-3 min.).

Electronic structure calculations have been carried out to examine the effect of protonation and water molecules on the heme group of peroxidases in different redox (ferric, ferrous, compounds I and II) and spin states. Shared geometries, spectroscopic properties at Soret region, and thermodynamics of peroxidases are discussed. B3LYP and M06-2X density functionals with different basis sets were employed on a common molecular model of the active site (Fe-centred porphine and proximal imidazole). Computed Gibbs free energies indicate that the corresponding aquo complexes are not thermodynamically stable, supporting the five-coordinate Fe(III) centre in native ferric peroxidases, with a water molecule located at a non-bonding distance. Protonation of the ferryl oxygen of compound II is discussed in terms of thermodynamics, Fe–O bond distances, and redox properties. It is demonstrated that this protonation is necessary to account for the experimental data and computed Gibbs free energies that reveal pKa values of compound II about 8.5 – 9.0. Computation suggests that the origin of the general oxidative properties of peroxidase species, as well as their reactivity towards water and protons and Soret spectral properties, mostly resides on the iron porphyrin and its proximal ligand histidine.

Geopolymer is an emerging material alternative to Portland cement and has potential as a refractory material. Adding filler in geopolymer material is a strategy to increase the advantages of its physical and mechanical properties. It has been previously reported that adding nanoparticles can increase the compressive strength value, but there is no reported interaction between nanoparticles and geopolymer during the geopolymerization process. This study aims to study the effect of adding nano-zirconia fillers on the physical and mechanical changes of metakaolin-based geopolymers with nano-zirconia fillers. The geopolymer samples were made with 100 g of metakaolin as the base material and nano-zirconia in amounts of 2 gr, 5 gr, 10 gr, and 15 gr. Further characterization was carried out by XRD, FTIR, and SEM-EDX. This study showed that the compressive strength of the MZr05 sample increased significantly by 58.7% compared to the control sample. The test results of the structure and functional groups did not lead to any new compounds formed in the geopolymerization reaction. Therefore, the interaction of metakaolin geopolymer with nano-zirconia only creates an interfacial bonding.

Environment approachable products such as fuels and lubricants are among the best choices in several countries that contain renewable products as alternatives. To protect human life, alternative methods of saving the environment and production balance is needed to reduce the effects of the crisis and the contamination of the Environment. This research concentrated on the Manufacturing and testing of bio- grease from sugar cane filter mud vegetable oil as a lubricant for friction reduction and determining the properties of both bio grease and Mineral oil grease with environmental problems. SC filter mud oil as an alternative use for bio-grease preparation in addition to mineral oil grease. The Testing was accepted to determine the quality of the eco-friendly grease produced. For the preparation of this bio- grease, the SC Filter cake sample is taken from different sugar factory which found in Ethiopia. The sample has a moisture content of 78%. Using this sample first oil is extracted by Soxhlet apparatus, n-hexane solvent and temperature for extraction from 42 -68℃. The maximum temperature and time for extraction of oil were 68 and 7hrs respectively. The extracted oil's physical properties include color, acid value, specific graphite, saponification value, iodine value, density, and viscosity. Finally, the friction behavior in function of time for both grease at identical load, the friction coefficient vs time for SC filter Cake Grease_ Na_ MoS2 and industrial mineral one (I_ Greasily _ MoS2), grease was determined.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

Deposition/printing of materials with sub-1 μm precision and size (cross sections) is required for optical and electrical micro-devices. Crystalline c-ITO (Indium tin oxide) nanostructures were patterned on glass with a precision that formed gaps of 20-50 nm between individual disks or lines of ∼ 250 nm diameter or width. The absorbed energy density [J/cm3] followed the second order dependence on pulse energy. This facilitated high resolution and precision for nanoscale laser writing at the 515 nm laser wavelength. Patterns for optical elements such as circular gratings and micro-disks were laser printed using ITO as a resist. Unexposed amorphous a-ITO was chemically removed in aqueous 1% vol. HF solution. This use of a-ITO as solid-resist is promising for metamaterial and micro-optical applications.

N,N-dimethyl-4-nitroaniline (NNDM4NA, C8H10O2N2), is a superelastic and superplastic charge-transfer molecular crystal with a high molecular dipole moment, µ=7.95 D, which crystal-lizes in the acentric polar point group 2. Highly aligned poly-l-lactic acid (PLLA) polymer micro-fibers with embedded NNDM4NA nanocrystals were fabricated using the electrospinning tech-nique. The composite fibers display an extraordinarily high piezoelectric output response, where for a small stress of 5.0x103 Nm-2, an effective piezoelectric voltage coefficient of geff=3.6 VmN-1 was obtained. The fibers were found to display solid state blue fluorescence with a long (147 ns) life-time decay. Furthermore, the composite fibers exhibit an average increase of 67% on the Young modulus reaching 55 MPa, while the tensile strength reaches 2.8 MPa when compared with solely PLLA fibers. The results show that nanocrystals, from small organic molecules, with elastic and piezoelectric properties form hybrid functional 2-dimensional luminescent array which are me-chanical strong and generate high output voltages making them promising for applications in energy harvesting and as solid-state blue emitters.

To mitigate lithium dissolution and polysulfide shuttle effect phenomena in high energy lithium sulfur batteries (LISBs), a conductive, flexible, and easily modified polymer composite layer was applied on the anode. The polymer composite layer includes polyaniline and functionalized graphite. The electrochemical behavior of LISBs was studied by galvanostatic charge/discharge tests from 1.7 to 2.8 V up to 90 cycles and via COMSOL Multiphysics simulation software. No apparent overcharge occurred during the charge state, which suggests that the shuttle effect of polysulfides was effectively prevented. The COMSOL Multiphysics simulation provides a venue for optimal prediction of the ideal concentration and properties of the polymer composite layer to be used in the LISBs. The testing and simulation results determined that the polymer composite layer diminished the amount of lithium polysulfide species and decreased the amount of dissolved lithium ions in the LISBs. In addition, the charge/discharge rate of up to 2.0 C with a cycle life of 90 cycles was achieved. The knowledge acquired in this study was important not only for the design of efficient new electrode materials, but also for understanding the effect of the polymer composite layer on the electrochemical cycle stability.

Fresh potatoes were deep-fried in olive oil (OO) & extra virgin olive oil (EVOO) and their blends with 5%, 10% and 20% v/v sesame oil (SO). This is the first report on the use of sesame oil as natural source of antioxidant for olive oil deep-frying. Oil was evaluated for Peroxide Value (PV), Free Fatty Acids (FFA), K₂₃₂, K₂₇₀, Trolox Equivalent Antioxidant Capacity (TEAC) and Total Phenols (TP) until Total Polar Compounds (TPCs) reached 25%. Sesame lignan transformations were monitored through Reverse-phase HPLC. While TPCs in olive oils increased at a steady rate, the addition of 5%, 10% and 20% v/v SO created a time window lasting 1, 2 and 3 hours, respectively, where TPCs were constant. SO addition to OO increased the total frying time. Furthermore, the addition of SO reduced the peroxides formation rate for both OO and EVOO. EVOO was more resistant to oxidation than OO as measured by TPCs and TEAC, while frying time raised from 21.5 to 25.25 h when EVOO replaced OO. The increase in frying time for olive oil but not for extra virgin olive oil, after SO addition, is pointing out a niche market for extra virgin olive oil in deep-frying.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

The depletion and environmental problems associated with fossil fuels have encouraged us to look for alternative feedstock that do not compromise food security and the environment. Sorghum is a fast-growing crop that can be harvested twice a year and produces both food and straw that can be utilized in the production of bio-based fuels. In this study, the production of bioethanol and the effects of fermentation parameters on ethanol yield are presented. A sequential pretreatment method was employed, using dilute sulfuric acid (1%) at 125 °C in the first stage and dilute sodium hydroxide (1.25 %) at 90 °C in the second stage. The residues left after the sequential pretreatment stage were hydrolyzed using acid hydrolysis. The sugar concentration of the hydrolysates was determined using the phenol sulfuric acid method, and three hydrolysates having sugar levels of 30.42 g/L, 31.79 g/L, and 32.9875 g/L were selected for fermentation. The ethanol yield was determined after 72 hours of fermentation at 30 °C with varying inoculum sizes (5%, 10%, and 15%) and pH (4.5, 5, and 5.5). With a maximum ethanol yield of 0.617 mL/g (48.742%) produced at a sugar content of 32.9875 g/L, pH of 5, and inoculum size of 15%, statistical analysis showed that all three independent parameters affected ethanol yield. According to these findings, while raising sugar content, inoculum amount, and pH all initially result in higher ethanol yields, doing so further reduces yield. So, in order to increase ethanol yield, fermentation conditions must be carefully managed while producing ethanol from sequential acidic-alkaline pretreated sorghum straw. The strategy followed by using sequential acidic-alkaline pretreatment of sorghum straw provides prospects for efficient and effective production of biofuels from alternative feedstock.

The addition of prebiotics is one of the most important ways to improve the techno-functional properties of bread. In this study, the effects of resistant starch, polydextrose, and inulin on the wheat flour, dough, and bread properties were investigated. In farinography results, resistant starch significantly increased the development time (2:18) with a boosting effect, but polydextrose (1:48) and inulin (1:36) weakened the dough (P &lt;0.05). Inulin, polydextrose, and resistant starch had the most effect on reducing water absorption (40, 43.2, and 48.9) respectively (P &lt;0.05). According to extensography data, inulin had the best result in baking compared to other polysaccharides. In terms of baked breads, samples containing resistant starch had high moisture that could be due to starch gelatinization and moisture-retaining, which delays the staling process of bread. Inulin, polydextrose, and resistant starch prebiotic ingredients affected dough rheological properties and bread quality, and organoleptic characteristics, however, resistant starch was the best.

ZnO was synthesized by Sol gel method using zinc nitrate as precursor at different calcination temperatures. Nucleation of ZnO crystallites and their growth with rise in temperature was observed. Exciton bands and lattice imperfections affected the absorption spectra. The decrease in band gap with temperature was due to the formation of defect energy levels. Phonon assisted non-radiative transitions caused broadening of the peaks. The possibility of tuning the band gap of ZnO by changing the temperature was explored. Simulation studies showed transition to single phase with rise in temperature.

The Sulfur Dioxide (SO2) compound is a primary environmental pollutant worldwide, whereas elemental Sulfur (S) is a global commodity possessing a variety of industrial as well as commercial functions. The chemical relationship between poisonous SO2 and commercially viable elemental S has motivated this investigation using Density Functional Theory calculation of the relative transition state barriers for the 2-step Dehydro-sulfurization oxidation-reduction reaction. Additionally, doubly-charged nanoscale platelet Molybdenum Disulfide (MoS2), Armchair (6,6) Carbon Nanotube, 28-atom Graphene nanoflake (GR-28), and Fullerene C-60 are utilized as catalysts. The optimal heterogeneous and homogeneous catalysis pathways of the 2-step oxidation-reduction from SO2 to elemental S are further inspired by the biomimicry of the honeybee species multi-step bio-catalysis of pollen conversion to organic honey. Potential applications include environmental depollution, the mining of elemental sulfur, and the functionalization of novel technologies such as the recently patented aerial and amphibious Lynchpin TM drones.

Pineapple is a highly demanded fruit in international markets, thanks to its unique appearance and flavor, high fiber content, vitamins, folic acid, and minerals. It makes the pineapple production and processing market a significant source of income for producing countries, such as Costa Rica. Nowadays, its processing produces a large amount of waste with negative consequences for the environment. However, pineapple waste is an essential source of cellulose, hemicellulose, lignin, and other high-value products like enzymes (bromelain). These by-products can be obtained by pineapple waste biorefinery, generating an additional source of export goods and foreign currency, framing pineapple processing in the concept of the circular economy. This review discusses how incorporating biorefinery in the pineapple production processes can contribute to the post-COVID 19 economy in Costa Rica. Pineapple production in Costa Rica is explored, and the contamination of generated residues is delineated. Furthermore, the primary processes for by-product extraction via biorefinery, their general characteristics and applications in the medical field, and their contribution to the circular economy are presented.

Within this work we review the metal coordination effect on the photophysics of metal dipyrrinato complexes. Dipyrrinato complexes are promising candidates in the search for alternative transition metal photosensitizers for application in photodynamic therapy (PDT). These complexes can be activated by irradiation with light of a specific wavelength, after which cytotoxic reactive oxygen species (ROS) are generated. The metal coordination allows for the use of the heavy atom effect, which can enhance the triplet generation necessary for generation of ROS. Additionally, the flexibility of these complexes for metal ions, substitutions and ligands allows the possibility to tune their photophysical properties. A general overview of the mechanism of photodynamic therapy and the properties of the triplet photosensitizers is given, followed by further details of dipyrrinato complexes described in the literature that show relevance as photosensitizers for PDT. In particular, the photophysical properties of Re(I), Ru(II), Ir(III), Ni(II), Cu(II), Pd(II), Pt(II), Zn(II), Ga(III), In(III), Al(III), Sn(II), and P dipyrrinato complexes are discussed. The potential for future development in the field of (dipyrrinato)metal complexes is addressed and several new research topics are suggested throughout this work. We propose that significant advances could be made for heteroleptic bis(dipyrrinato)zinc(II) and homoleptic bis(dipyrrinato)palladium(II) complexes and their application as photosensitizers for PDT.

Grafting polyethylene glycol (PEG) on polymers surface is widely used to improve biocompatibility by reducing protein and cell adhesion. Although PEG is considered to be bioinert, its incorporation to biomaterials has shown to improve cell viability depending on the amount and molecular weight (MW) used. This phenomenon was studied here by grafting PEG of three MW onto polyurethane (PU) substrata at three molar concentrations to assess their effect on PU surface properties and on the viability of osteoblasts and fibroblasts. PEG formed a covering on the substrata which increased the hydrophilicity and surface energy of PUs. Among the results it was observed that osteoblast viability increased for all MW and grafting densities of PEG employed compared with unmodified PU. However, fibroblast viability only increased at certain combinations of MW and grafting densities of PEG, suggesting an optimal level of these parameters. PEG grafting also promoted a more spread cell morphology than that exhibited by unmodified PU; nevertheless, cells became apoptotic-like as PEG MW and grafting density were increased. These effects on cells could be due to PEG affecting culture medium pH, which became more alkaline at higher MW and concentrations of PEG. Results support the hypothesis that surface energy of PU substrates can be tuned by controlling the MW and grafting density of PEG, but these parameters should be optimized to promote cell viability without inducing apoptotic-like behavior.

This study evaluated the efficacy of experimental TEGDMA-functionalized dicalcium phosphate dihydrate (T-DCPD) filler-based resin-based composites (RBC) in preventing caries lesions around the restoration margins (secondary caries”, SC). Standardized Class-II cavities were made in sound molars having the cervical margin in dentin. Cavities were filled with a commercial resin-modified glass-ionomer cement (RMGIC) or experimental RBCs containing a BisGMA-TEGDMA resin blend and one of the following inorganic fractions: 60 wt.% Ba glass (RBC-0); 40 wt.% Ba glass, 20 wt.% T-DCPD (RBC-20); 20 wt.% Ba glass, 40 wt.% T-DCPD (RBC-40). An open-system bioreactor produced S. mutans biofilm-driven SC. Specimens were scanned using micro-CT to evaluate demineralization depths. Scanning Electron Microscopy and Energy-dispersive X-ray Spectroscopy characterized the specimens’ surfaces, while antimicrobial activity, buffering effect, and ion uptake by the biofilms were also evaluated. ANOVA and Tukey’s test were applied at p<0.05. RBC-0 and RBC-20 showed SC development in dentin, while RBC-40 and RMGIC significantly reduced the lesion depth at the restoration margin (p<0.0001). Initial enamel demineralization could be observed only around RBC-0 and RBC-20 restorations. A direct antibiofilm activity could explain SC reduction by RMGIC, while a buffering effect on biofilm’s acidogenicity explained the behavior of RBC-40. Experimental RBC with CaP-releasing functionalized T-DCPD filler could prevent SC with the same efficacy as F-releasing materials.

heterocycles are particularly common moieties within marine natural products. Specifically, tetrahydrofuranyl rings are present in a variety of compounds which present complex structures and interesting biological activities. Focusing on terpenoids, a high number of tetrahydrofuran-containing metabolites have been isolated during the last decades. They show promising biological activities, making them potential leads for novel antibiotics, antikinetoplastid drugs, amoebicidal substances or anticancer drugs. Thus, they have attracted the attention of the synthetic community, and numerous approaches to their total syntheses have appeared. Here, we offer the reader an overview of marine-derived terpenoids and related compounds, with a special focus on their isolation, structure determination, biological profiles and total syntheses.

In this review paper, the occurrence in the plant kingdom and the biological activities associated to two specific phenyl-ethanoid glycosides i.e., leucosceptoside A and leucosceptoside B, were shown and discussed. This is the first work ever done on such subject. Analysis of the literature data clearly indicates that leucosceptoside A is much more common in plants and exerts many more biological activities than leucosceptoside B even if this also presents some important elements. All of this was widely discussed in this paper.

The thermodynamic phase behavior of charged polymers is a crucial property underlying their role in biology and various industrial applications. A complete understanding of the phase behaviors of such polymer solutions remains challenging due to the multi-component nature of the system and the delicate interplay among various factors, including the translational entropy of each component, excluded volume interactions, chain connectivity, electrostatic interactions, and other specific interactions. In this work, the phase behavior of partially charged, ion-containing polymers in polar solvents is studied by further developing a liquid-state (LS) theory with local short-range interactions. This work is based on the LS theory developed for fully-charged polyelectrolyte solutions. Specific interactions between charged groups of the polymer and counterions, between neutral segments of the polymer, and between charged segments of the polymer are incorporated into the LS theory by an extra Helmholtz free energy from the perturbed-chain statistical associating fluid theory (PC-SAFT). The influence of the sequence structure of the partially charged polymer is modeled by the number of connections between bonded segments. The effects of chain length, charge fraction, counterion valency, and specific short-range interactions are explored. A computational App for salt-free polymer solutions is developed and presented, which allows easy computation of the binodal curve and critical point by specifying values for the relevant model parameters.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

Plastic waste management has become a major problem in the present times, and many countries are struggling to deal with it. The situation has become a crisis in developing nations due to a lack of proper waste management, resources, technology, and political will. The extensive usage of foam-based packaging materials such as Styrofoam as a secondary packaging material has led to environmental pollution both in land and water, in developing countries. It is important to address this problem using a sustainable approach such as biomimetic manufacturing. One such solution that is present in developed nations is mycelium-based packaging, wherein the agricultural and industrial-based cellulose waste is converted into a biocomposite with the help of a fungi root network. Such a process has the potential to convert biomass into useful products but also has an indirect effect on pollution reduction by eliminating stubble burning in nations like India. In this review, we examine the details of the manufacturing process, properties, advantages, and limitations of such composite materials. A comparison of the present status of such materials produced in the market by some of the companies across the world is presented. Finally, the challenges involved with such materials and the future directions are discussed.

Residual stresses in fiber metal laminates (FML) inevitably develop during the manufacturing process. The main contributor to these stresses is the difference in the coefficients of thermal expansion (CTE) between fibers and metal in combination with high process temperatures. To quantify these stresses, the use of specimens with an asymmetric layup is an easily adaptable method. The curvature that develops after the manufacturing of flat laminates with an asymmetrical layer stack is a measure of the level of residual stresses evolving during cure. However, the accuracy of the curvature evaluation is highly dependent on specimen design and other influencing parameters. In this work a large set of FML specimens is investigated to identify relevant influencing parameters and derive conclusions about specimen design and evaluation techniques. For certain layups and process parameters, there is a good correlation between the curvature and the stress-free temperature, which is further covered by analytical solutions for bimetals. This correlation is the basis to transfer curvature into a stress-free temperature that can consequently be used for the quantification of residual stress levels in more complex FMLs. The transfer is validated by in-situ strain measurements during cure using a strain gage technique. Based on the results, the application of asymmetric specimens for residual stress characterization in more complex laminates is presented in the form of a workflow.

One of the significant challenges today in the brain-machine interface using invasive methods is the stability of the chronic record. In recent years, polymer-based electrodes have gained notoriety for achieving mechanical strength values close to that of brain tissue, promoting a lower immune response to the implant. In this work, we fabricated fully polymeric electrodes based on PEDOT:PSS for neural recording in Wistar rats. We characterized the electrical properties and both in-vitro and in-vivo functionality of the electrodes. Also, we employed histological processing and microscopical visualization to evaluate tecidual immune response in 7, 14, and 21 days post-implant days. Electrodes with 400-micrometer channels showed a 12dB signal-to-noise ratio. Local field potentials were characterized under two conditions: anesthetized and free-moving. There was a proliferation of microglia to the tissue-electrode interface in the first days, with a decrease after 14 days. Astrocytes also migrated to the interface, but there was no continuous recruitment of these cells in the tissue, showing inflammatory stability at 21 days. The signal was not affected by this inflammatory action, demonstrating that fully polymeric electrodes can be an alternative to prolong the valuable time of neural recordings.

Epidermal Growth Factor Receptor (EGFR) tyrosine kinase is a cell surface receptor whose overexpression has been associated with different types of cancers including brain cancer (glioblastoma multiforme). The ability of the extract of Scutellaria baicalensis to inhibit the proliferation of malignant glioma cells have been reported. Thus, in this study we report the identification of 307 bioactive constituents responsible for the anti-glioblastoma multiforme effect from S. baicalensis using in silico studies such as molecular docking, binding free energy calculations, pharmacophore modelling, induced-fit docking, gene enrichment analysis, molecular dynamic simulations and ADMET predictions. A total of 307 chemical constituents of S. baicalensis were screened and the top 10 scoring compounds indicated different binding affinities ranging from -9.010 to -6.427 kcal/mol towards the EGFR tyrosine kinase; Ganhuangenin, 5,7,2',5'-tetrahydroxyflavone, (2R)-2-(2,6-dihydroxyphenyl)-3,4-dihydro-2H-chromene-5,7-diol, and tenaxin I possess higher binding affinities (-9.010 to -8.649 kcal/mol) compared to the standard ligand, erlotinib having -8.539 kcal/mol. The compounds interacted with amino acids of clinical importance such as MET 769, GLU 738, THR 766 via H-bond. The structural features involved in the interaction with the target were mostly two aromatic rings, H-bond donors and acceptors and some hydrophobic interactions which varies between the ligands. Better docking scores in the induced-fit docking further validates the inhibitory potential of the compounds against the flexible protein. All the top-scoring ligands from S. baicalensis had zero Lipinski violation and also obeyed other drug-likeness rules by Ghose, Veber, Egan, and Muegge with the exception of breviscapine. Interestingly, all the compounds are not likely to be hepatotoxic, mutagenic, or cytogenic, making them potentially safe as anti-cancer agents.

G protein-coupled receptors (GPCRs) are amongst the most pharmaceutically relevant and well-studied protein targets, yet unanswered questions in the field leave significant gaps in our understanding of their nuanced structure and function. 3D pharmacophore models are powerful computational tools in silico drug discovery, presenting myriad opportunities for the integration of GPCR structural biology and cheminformatics. This review highlights success stories in the application of 3D pharmacophore modeling to de novo drug design, discovery of biased and allosteric ligands, scaffold hopping, QSAR analysis, hit-to-lead optimization, GPCR de-orphanization, mechanistic understanding of GPCR pharmacology and elucidation of ligand-receptor interactions. Furthermore, advances in the incorporation of dynamics and machine learning will be highlighted. The review will analyze challenges in the field of GPCR drug discovery, detailing how 3D pharmacophore modeling can be used to address them. Finally, we will present opportunities afforded by 3D pharmacophore modeling in the advancement of our understanding and targeting of GPCRs.

A method is developed to identify molecular scaffolds potentially active against the Mycobacterium tuberculosis complex (MTBC). A structurally heterogeneous set of compounds active against MTBC was used to obtain a structural pattern model based on structural invariants. This model was statistically validated through a Leave-n-Out test. It successfully discriminated between active or inactive compounds over 86% in database sets and was also able to select new active chemical structures in external databases. The selection of new substituted pyrimidines, pyrimidones and triazolo[1,5-a]pyrimidines was particularly interesting because these structures could provide new scaffolds in this field. The seven selected candidates were synthesized and six of them showed activity in vitro.

Since its introduction, back in the late 1970s, the non-affine or slip parameter, ξ, has been routinely employed by numerous constitutive models as a constant parameter. However, the evidence seems to imply that it should be a function of polymer deformation. In the present work, we phenomenologically modify a constitutive model for the rheology of unentangled polymer melts [P. S. Stephanou et al. J. Rheol. 53, 309 (2009)] to account for a non-constant slip parameter. The revised model predictions are compared against newly accumulated rheological data for a C48 polyethylene melt obtained via direct non-equilibrium molecular dynamics simulations in shear. We find that the conformation tensor data are very well predicted; however, the predictions of the material functions are noted to deviate from the NEMD data, especially at large shear rates.

Hexane is a solvent used extensively in the food industry for the extraction of various products such as vegetable oils, fats, flavours, fragrances, colour additives or other bioactive ingredients. As it is classified as a "processing aid", it does not have to be declared on the label under current legislation. Therefore, although traces of hexane may be found in final products, especially in processed products, its presence is not known to consumers. However, hexane, and in particular the n-hexane isomer, has been shown to be neurotoxic to humans and has even been listed as a cause of occupational diseases in several European countries since the 1970s. In order to support the European strategy for a toxic-free environment (and toxic-free food), it seemed important to collect scientific information on this substance by reviewing the available literature. This review contains valuable information on the nature and origin of the solvent hexane, its applications in the food industry, its toxicological evaluation and possible alternatives for the extraction of natural products. Numerous publications have investigated the toxicity of hexane, and several studies have demonstrated the presence of its toxic metabolite 2,5-hexanedione (2,5-HD) in the urine of the general, non-occupationally exposed population. Surprisingly, a tolerable daily intake (TDI) has apparently never been established by any food safety authority. Since hexane residues are undoubtedly found in various foods, it seems more than necessary to clearly assess the risks associated with this hidden exposure. A clear indication on food packaging and better information on the toxicity of hexane could encourage industry to switch towards one of the numerous other alternative extraction methods already developed.

One of the modern methods of improving operating characteristics of titanium and titanium-based alloys under conditions of friction and increased contact loads is the method of ion-plasma nitriding. The effect of nitriding of VT5 alloy (Al 4,5-6,7 %, V to 1,2 %, Mo to 0,8 % − analogue 3.7115) in the plasma of a glow discharge excited in a hollow cathode on its tribological characteristics in pairs with different materials in T-1 fuel and under dry friction conditions has been studied. For research and tribological tests, samples of VT5 alloy were nitrided in the plasma of a glow discharge excited in a hollow cathode at a temperature of 975 ± 15°C and a pressure of 58 ± 2 PA in a nitrogen-argon gas mixture with a nitrogen content of 78 %. Studies of samples of VT5 alloy after nitriding showed that the surface roughness Ra was in the range of 0.58-0.64, and the surface hardness HV5 was 525 ± 20 kgf/mm² at a base hardness of 325 ± 15 kgf/mm². Tribological tests were performed on a friction machine 2070 SMT-1 according to the scheme "cube - roller". Tests under conditions of friction with oil were performed at a load of 200 N. The sliding speed during the tests was 1.3 m/s, the test time was 75 sec. The test under dry friction conditions was carried out at a load of 100 N and a sliding speed of 0.785 m/s, the test time was 30 minutes. Low wear ability in relation to the nitrided titanium alloy VT5 (<2.4x10^-4 mm³/s), as well as friction coefficients at the level of 0.08 to 0.12 in the order of their growth had bronze VB-23NTS (Pd 18–22 %, Ni 3–4 %, Zn 3–4 %, Sb 3–4 %, P 0.15–0.3) r.O10C2N3, VB-24 (Sb 4.7–6, 2 %, P 0.4–0.9), steel 1.3505, cast iron GGG80, cemented steel 20Cr3MoWV.

Since 2007, at the Electron Science Research Institute (ESRI) nano-fabrication laboratories, Edith Cowan University, Australia, we have devoted research efforts to the synthesis and characterization of bismuth-containing ferrite-garnet-type thin-film magneto-optic (MO) materials of different compositions. We report on the development and properties of highly bismuth-substituted iron-garnet thin films prepared by using radio frequency (RF) magnetron sputtering. We study the process parameters associated with the RF magnetron sputter deposition technique and investigate the results of optimizing process parameters and implementing several special techniques including the fabrication of co-sputtered nanocomposite films, all-garnet multilayer structures, applying oxygen plasma treatment on amorphous garnet layers just after the deposition process, and designing modifications of the annealing crystallization process and regimes for achieving the best MO properties. We demonstrated significant improvement in MO properties of Bi-containing ferrite-type garnet thin-film materials, including record-high MO figures of merit and improved conventional and un-conventional hysteresis loops of Faraday rotation. The attractive optical, magnetic, and magneto-optic properties obtained in highly bismuth-substituted iron garnet thin-film materials of multiple composition types are relevant in the context of manufacturing next-generation ultra-fast optoelectronic devices, such as light intensity switches and modulators, high-speed flat panel displays, and high-sensitivity sensors.

Several biomedical products, like scaffolds, implants, prostheses, and orthoses, require materials having superior physicochemical and biological properties. Polyethylene terephthalate glycol (PETG) is being increasingly used for various biomedical applications. There are a few studies on PETG-based composites, however, natural fibers like silk short fibers reinfored PETG composites have not been attempted. Being a cost-effective widely available material, PETG-Silk combination can be potential biocomposite for several biomedical applications. Here, we report a novel short silk fiber reinforced PETG composite prepared by a wet-mixing route, ensuring homogenous dispersion of the filler. Different ratios (2-10%) of short silk fibers were used to prepare composites with varied compositions. The mechanical, physicochemical, and biological properties of the prepared composites were analyzed. Thermogravimetric analysis showed that such composites are thermally stable up to 390 °C and can be used for thermal extrusion-based manufacturing. The tensile modulus of the samples increased with fiber content; however, the failure strain reduced with fiber content. Furthermore, upon annealing, the tensile modulus increased but, the failure strain of the composites decreased, XRD study revealed that heat treatment has altered the crystalline nature of the composites. Finally, we evaluated the cytocompatibility of the prepared composites to assess their suitability for various biomedical applications.

Evaluation of the mobility behavior of radionuclides in highly saline and alkaline conditions is a major concern for performance assessment of radioactive waste disposal. The aim of this study is to determine the effect of up to 2.8 mol/kgsolution content of NaNO3, onto the solubility and the sorption of U(VI) in a hardened cement-paste (HCP) prepared from an ordinary Portland cement (CEM I). To avoid the interference of the high salt concentration (and ionic strength) and because of expected low solubility of uranium under such alkaline conditions, the time-resolved laser fluorescence (TRLFS) was selected to measured accurate U(VI) concentration in solution using the standard addition method in 85% H3PO4 to limit dilution and matrix effects and allows determining of resulting [U(VI)] in solution with acceptable precision for distribution factor (Rd) both in sorption and desorption experiments. The operational solubility limit measured at high ionic strength is lowered by a factor 3 compared to the reference cementitious condition, with the Rd values decrease by ca. a factor 4. Sorption of U(VI) appears to be reversible under these conditions.

Hydrogels can provide instant relief to pain and facilitate the fast recovery of wounds. Currently the incorporation of medicinal herbs/plants in polymer matrix is being investigated due to their anti-bacterial and wound healing properties. Herein, we investigated the novel combination of chitosan (CS), chondroitin sulfate (CHI) and garlic (Gar) to synthesize hydrogels through freeze gelation process for faster wound healing and resistance to microbial growth at the wound surface. The synthesized hydrogels were characterized via Fourier transform infrared spectroscopy (FTIR), which confirmed the presence of relevant functional groups. The scanning electron microscopy (SEM) images exhibited the porous structure of the hydrogels, which is useful for the sustained release of Gar from the hydrogels. The synthesized hydrogels showed significant inhibition zones against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). Furthermore, cell culture studies confirmed the cyto-compatibility of the synthesized hydrogels. Thus, the novel hydrogels presented in this study can offer antibacterial effect during wound healing and promote tissue regeneration.

In the recent decade, metal-based conductive nano-inks comprising of nanometer-sized metallic particles of high electrical conductivity (mainly Ag and Cu) suspended in a polymer have revolutionized the field of printed electronics. The present review aims to provide an overview of the current state of research in synthesis and characterization techniques for metallic nano-inks and associated challenges. Moreover, the end of the review will discuss future perspectives in this field (from industrial and academic viewpoints).

Oxalate is a divalent organic anion that has implications across many biological and commercial processes. It is derived from plant sources, such as spinach, rhubarb, tea, cacao, nuts, and beans, and therefore is commonly found in raw or processed food products. Oxalate can also be made endogenously by humans and other mammals as a byproduct of hepatic enzymatic reactions. It is theorized that oxalate is useful for plants to store calcium and protect against herbivory. Clinically, oxalate is best known to be a major component of kidney stones, which commonly contain calcium oxalate crystals. Oxalate can induce an inflammatory response that decreases the immune system’s ability to remove renal crystals. When formulated with platinum as oxaliplatin (an anticancer drug), oxalate has been proposed to cause neurotoxicity and nerve pain. There are many sectors of industry that are hampered by oxalate, and some that depend on it. For example, calcium oxalate is troublesome in the pulp industry and the alumina industry as it deposits on machinery. On the other hand, oxalate is a common active component of rust removal and cleaning products. Due to its ubiquity, there is interest in developing efficient methods to quantify oxalate. Over the past four decades several diverse methods have been reported. These approaches include electrode-based detection, liquid chromatography or gas chromatography coupled with mass spectrometry, enzymatic degradation of oxalate with oxalate oxidase and detection of hydrogen peroxide as a product, and indicator displacement-based methods employing fluorescent or UV light-absorbing compounds. It has become clear that no single method will work best for every purpose. This review describes the strengths and limitations of each method, and may serve as a reference for investigators to decide which approach is most suitable for their work.

The effect of Mg particles on PLA's thermal, chemical, physical, and mechanical properties has been studied. The thermal and physical properties have been studied by differential scanning calorimetry, analysing the stability of the α and α’-crystals of the PLA. A colloidal route was used to introduce Mg particles inside the PLA matrix, ensuring a good dispersion of the particles. Materials with Mg contents from 0 to 10 wt.% have been prepared, with additions of polyethyleneimine (PEI) and polyethylene glycol (PEG). Fourier Transform Infrared Spectroscopy has been used to confirm the influence of Mg, PEI, and PEG on PLA properties. The mechanical properties have been measured with a universal tensile test machine on printed filaments via Fused Filament Fabrication (FFF), which were naturally aged to stable conditions. Filaments with and without a notch were studied to obtain the materials' tensile strength, elastic modulus, and fracture toughness. Different analytical models to explain the results of the PLA-Mg were studied, in which the interface strength of the PLA-Mg composites was calculated.

We describe the design and fabrication of an industrial injection moulding system which can be mounted and used on the NCD-SWEET Small-angle X-Ray Scattering Beamline at ALBA. We show how highly useful time-resolved data can be obtained using this system. We are able to evaluate the fraction of material in the mould cavity and identify the first material to solidify and how this varies with the injection tem-perature. The design follows current industrial practice and provides opportunities to collect time-resolved data at several points within the mould cavity so we can build up a 4D perspective of the morphology and its temporal development. The quantitative data obtained will prove invaluable for the optimisation of the next generation of in-jection moulding techniques. This preliminary work used results from the injection moulding of a general purpose isotactic polypropylene.

Toxic materials in waste generally contain several components of global trending pollutant categories, especially PAHs and heavy metals. Bioremediation technology for managing waste utilizing microorganisms (bacteria) has not been fully capable of breaking down these toxic materials simple and environmentally friendly chemical products. This study examines the potential application of a marine sponge symbiont consortium with high performance and efficiency in removing PAHs and heavy metal contaminants. The method is carried out through a review of some related research articles by the author and published by other re-searchers. The study results concluded that bioremediation technology development GTP, can be carried out to improve remediation efficiency. Several types of marine sponge symbiont bacteria, hydrocarbonoclastic (R-1), metalloclastic (R-2), and metallohydro-carbonoclastic (R-3), have the potential to be applied to improve the removal performance of waste. Bacterial screening be done to find and categorize R-1 bacteria, R-2; R-3 to remediate GTP. Develop of R-1 bacteria, R-2; R-3 forms of the mobile formulation are needed in the future. A crystalline consortium of bacteria preparations is needed so that they can be quickly mobilized to locations exposed to GTP. Marine sponge symbiont bacteria be traced mainly to marine sponges whose body surface is covered with mucus.

Wounds represents a medical problem that contribute importantly to patient morbidity and to the healthcare costs in several pathologies. In Hidalgo, Mexico, Bacopa procumbens plant has been traditionally used for wound healing care for several generations; in vitro and in vivo experiments were design to evaluate the effects of bioactive compounds obtained from B. procumbens aquoethanolic extract and to determine the key pathways involved in wound regeneration. Bioactive compounds were characterized by HPLC- QTOF-MS and proliferation, migration, adhesion, and differentiation studies were done on NIH/3T3 fibroblasts. Polyphenolic compounds from Bacopa procumbens (PB) regulated proliferation and cell adhesion; enhanced migration reducing the artificial scratch area; and modulated cell differentiation. PB compounds were included in a hydrogel for topical administration on rat excision wound model. Histological, histochemical and mechanical analysis showed that PB treatment accelerates wound closure in at least 48 h; reduce inflammation, increasing cell proliferation and deposition and organization of collagen in earlier times. These changes resulted in the formation of a scar with better tensile properties. Immunohistochemistry and RT-PCR molecular analyses demonstrated that treatment induces: i) overexpression of transforming growth factor beta (TGF-β); and ii) the phosphorylation of Smad 2/3 and ERK1/2, suggesting the central role of some PB to enhance wound healing, modulating TGF-β activation.

Bonding agents (BA) are key compounding ingredients for the correct formulation of composite solid rocket propellants (CSRP). In particular, the addition of BA is essential to achieve suitable mechanical properties of CSRP in terms of adequate tensile strength and elongation at break. It is shown that the polarity of each conventional BA as well as new potential BA can be measured through the Reichardt’s ET(30) polarity scale. Using this criteria it was possible to find a substitute for MAPO (tris-(methylaziridinyl)-phosphine oxide), a conventional BA with the drawback of high toxicity and high reactivity, with TTPT (tris-(pyrrolidine)-phosphine oxide), a completely safe and effective BA. In this work, many other potential BA were evaluated through the Reichardt’s ET(30) polarity scale but only a selection of the potential BA were effectively tested in a standard CSRP. Particular interesting was the evaluation of TTPT vs MAPO showing the ability of the former BA to match the mechanical properties of the latter BA.

Flammability was evaluated and the results showed the values of critical flux at extinguishment (CFE) as 49.5kW/㎡ on average, total heat release (Qt) as 0.21MJ on average, and peak heat release rate (Qp) as 0.66kW on average, which satisfied all of the thresholds presented by the IMO. Therefore, flame-retardant plywood, of which the flame-retardant performance was evaluated, was determined to be an applicable finishing material that satisfies fire safety standards.

In a continuation and extension of an earlier publication, the calculation of the refractivity and polarizability of organic molecules at standard conditions is presented, applying a commonly applicable computer algorithm based on an atom-group additivity method, where the molecules are broken down into their constituting atoms, these again being further characterized by their immediate neighbor atoms. The calculation of their group contributions, carried out by means of a fast Gauss–Seidel fitting calculus, used the experimental data of 5988 molecules from literature. An immediate subsequent ten-fold cross-validation test confirmed the extraordinary accuracy of the prediction of the molar refractivity, indicated by a correlation coefficient R^2 and a cross-validated analog Q^2 of 0.9997, a standard deviation σ of 0.38, a cross-validated analog S of 0.41, and a mean absolute deviation of 0.76%. The high reliability of the predictions has been exemplified with three classes of molecules: ionic liquids, silicon- and boron-containing compounds. The corresponding molecular polarizabilities have been calculated indirectly from the refractivity using the inverse Lorentz-Lorenz relation. In addition, it could be shown that there is a close relationship between the "true" volume and the refractivity of a molecule, revealing an excellent correlation coefficient R^2 of 0.9645 and a mean absolute deviation of 7.53%.