Polydimethylsiloxane with hydroxy groups was functionalized to form functionalized polydimethylsiloxane, which subsequently underwent an addition reaction with isophorone diisocyanate to form the prepolymer. Next, 3-aminopropyltriethoxysilane (APTS) reacted with 3-glycidoxypropyltrimethoxysilane (GPTS) to produce bridged polysilsesquioxanes, and the sol–gel technology was employed to form hyperbranched polysiloxane nanoparticles with hydroxy groups, which was used as the additive. The hyperbranched polysiloxane and the prepolymer containing NCO functional groups then underwent an addition reaction to produce the hybrid materials. Fourier-transform infrared spectroscopy and 29Si nuclear magnetic resonance were used to characterize the structure of the polyurethane hybrid. Regarding thermal stability, after the hyperbranched polysiloxane nanoparticles was introduced, the integral procedural decomposition temperature increased from 348 ºC for polyurethane matrix to 859 ºC for the hybrid material. The results revealed that the thermal stability of the hybrid material substantially increased by approximately 247%.

This study analyzed the structural changes of semicrystalline polylactide (PLA) in the form of spun-bonded mulching nonwoven, during outdoor composting. The investigation was carried out at the microstructural, supramolecular and molecular levels using scanning electron microscopy (SEM), wide-angle X-ray diffraction (WAXD) and the viscosity method, respectively. The results showed the varying degree of influence of the climatic condition, prepared compost mixtures and time on the molecular, supramolecular and micromorphological structure of PLA spun-bonded mulching nonwoven and its degradation rate. The obtained experimental results revealed how the popular outdoor composting method, realized under two different European climatic conditions (in Poland and in Bulgary), affects the degradation of PLA nonwoven, designed for agriculture use.

The effects of carbon fiber hybridisation on the thermal properties of woven kenaf reinforced epoxy composites kenaf fibre were studied. Woven kenaf hybrid composites at the different weave designs of plain and satin, and fabric count of 5 × 5 and 6 × 6 were manually prepared by vacuum infusion technique. Thermal properties of pure carbon fibre and hybrid composites were conducted by using thermogravimetric analyser (TGA) and differential scanning calorimeter (DSC). It was found that at high kenaf fibre content showed better thermal stability while the highest thermally stable was found in pure carbon fibre composite. The TG and DTG results showed that the amount of residue decreased in plain-designed hybrid composite compared to satin-designed hybrid composite. The DSC data revealed that the presence of woven kenaf increase decomposition temperature.

Vitrimers are covalent network materials, comparable in structure to classical thermosets. Unlike normal thermosets, they possess a chemical bond swap mechanism that makes their structure dynamic and suitable for activated welding and even autonomous self-healing. The central question in designing such materials is the trade-off between autonomy and material stability: The swap mechanism facilitates the healing but it also facilitates creep, which makes the perfectly stable self-healing solid a hard goal to reach. Here, we address this question for the case of self-healing vitrimers made from star polymers. Using coarse-grained molecular dynamics simulations, we study the adhesion of two vitrimer samples and find that they bond together on timescales that are much shorter than the stress relaxation time. We show that the swap mechanism allows the star polymers to diffuse through the material through coordinated swap events, but the healing process is much faster and does not depend on this mobility.

This review is focused on current state-of-the-art research on electroactive-based materials and their synthesis, as well as their physicochemical and biological properties. Special attention is paid to pristine intrinsically conducting polymers (ICPs) and their composites with other organic and inorganic components, well-defined micro- and nanostructures, and enhanced surface areas compared with those of conventionally prepared ICPs. Hydrogels, due to their defined porous structures and being filled with aqueous solution, offer the ability to increase the amount of immobilized chemical, biological or biochemical molecules. When other components are incorporated into ICPs, the materials form composites; in this particular case, they form conductive composites. The design and synthesis of conductive composites result in the inheritance of the advantages of each component and offer new features because of the synergistic effects between the components. The resulting structures of ICPs, conducting polymer hydrogels and their composites, as well as the unusual physicochemical properties, biocompatibility and multi-functionality of these materials, facilitate their bioapplications. The synergistic effects between constituents have made these materials particularly attractive as sensing elements for biological agents, and they also enable the immobilization of bioreceptors such as enzymes, antigen–antibodies, and nucleic acids onto their surfaces for the detection of an array of biological agents. Currently, these materials have unlimited applicability in biomedicine. In this review, we have limited discussion to three areas in which it seems that the use of ICPs and materials, including their different forms, are particularly interesting, namely, biosensors, delivery of drugs and tissue engineering.

The preparation and thermal properties of polypropylene foils, filled with ceramic microparticles, talc or boron nitride, are described. A slow, linear increase of thermal conductivity with volume percent of filler up to 30 vol % is detected. Reduction of the foil thickness bellow 200 micrometers leads to a significant increase of thermal conductivity. Specific thermal capacities of foils are temperature dependent, they decrease with filler incorporation.

Polypropylene (PP) foam has a great deal of application since it normally exhibits non-uniform cell size distribution, low cell density, and cracked cells. In this study, a small amount of fluoroelastomer (FKM) was used as a nucleating agent to prepare well-defined microporous PP foam by supercritical CO₂. It was observed that solid FKM was present as the nanoscale independent phase in PP matrix and the FKM could induce a mass of CO₂ aggregation, which significantly enhanced the diffusion rate of CO₂ in PP. The resultant PP/FKM foams exhibited much smaller cell size (～24 μm), and more than 16 times cell density (3.2×10⁸ cells/cm³) as well as a much more uniform cell size distribution than that of the neat PP foam. PP/FKM foams possessed major concurrent enhancement in their tensile stress and compressive stress compared to neat PP foam. We believed that the added FKM played a key role in enhancing the heterogeneous nucleation, combined with the local strain field variation in the multiple-phase system, which was responsible for the considerably improved cell morphology of PP foaming. This paper provides a deep understanding of the scCO₂ foaming behavior of PP in the presence of FKM.

Synergistic effect of different fillers is widely utilized in polymer technology. The combination of various types of fillers is used to improve various properties of polymer composites. In this paper a synergistic effect of flame retardants was tested for the improvement of ceramizable composites performance. The composites were based of styrene-butadiene rubber (SBR) used as polymer matrix. Three different types of flame retardants were tested for synergistic effect: Mica (phlogopite) high aspect-ratio platelets along with low softening point temperature glass frit (featuring ceramization effect) and melamine cyanurate, a commonly used flame retardant promoting carbonaceous char. In order to characterize the properties of the composites, combustibility, viscoelastic properties and mechanical properties before and after ceramization were tested. The results obtained show that the synergistic effect of ceramization promoting fillers and melamine cyanurate is especially visible with respect to the flame retardant properties resulting in a significant improvement of fire resistance of the composites.

Two region asymmetric polymers PR2F and PR1F with three repeat units of A-D-A, π-D-A, and π-D-π along the polymer backbone were attained by polymerizing different fluorinated benzothiadiazole-thiophene units, FBT-T and 2FBT-T units (A–π), with benzodithiophene unit (D), respectively. Here, the new region asymmetric polymers were in contrast to the traditional polymers featuring a D–A or D–π–A–π backbone. Both the region asymmetric polymers showed a low lying of HOMO energy level in relation to that of the PC61BM acceptor and then obtained the high open-circuit voltage of ~1 V in both PR2F and PR1F devices. Bulk-heterojunction devices based on PR2F with difluorinated BT exhibited an appreciable power conversion efficiency (PCE) of 4.73% due to the relatively high and balanced charge carrier mobilities, while the mono-fluorinated BT polymer PR1F-based devices gave a lower PCE of 2.92%. These results indicate that the region asymmetric conjugated polymer is a promising class of materials for polymer solar cell applications, and it is significant to further understand the influence of polymer structure on optoelectronic properties.

Dynamic mechanical analysis (DMA) is a versatile technique that complements the information given by the more traditional thermal analysis techniques such as differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and thermal mechanical analysis (TMA). Dynamic constants such as storage modulus, loss modulus, and loss factor are temperature dependent and provide information about interfacial bonding between reinforced fibre and polymer matrix of composite material. To study the above mentioned properties at the glass transition region, for unidirectional fibrous composites reinforced with continuous fibers a reliable model was applied. In particular, the composite material was considered as composed of three phases with the intermediate phase between matrix and fibres, the interphase, to have variable properties depending on those of main phases and the mode of preparation of the overall material. The glass transition temperature is defined as the point at which the specific volume versus temperature curve changes abruptly slope marking the region between rubbery polymer and glassy polymer nature. Hence, the behaviour of unidirectional fibrous composites was investigated at this region. Examination of the glass transition temperature, which constitutes an upper limit for the structurally important glassy region through the loss factor, was performed by its consideration as a combination of glass transition temperature of matrix and interphase.

In this work, an enzymatic sensor, based on a bionanocomposite film consisting of a polyelectrolyte complex (PEC) [Chitosan/kappa-carrageenan] doped with gold nanoparticles (AuNPs) encapsulating glucose oxidase (GOD) deposited on a gold electrode (Au) for glucose sensing, is described. Using the electrocatalytic synergy of AuNPs and GOD as a model of enzyme, the variation of the current (µA) as a function of the log of the glucose concentration (log [glucose]), shows 3 times higher sensitivity for the modified electrode (283.9) compared to that of the PEC/GOD modified electrode (93.7), with a detection limit of about 5 µM and a linearity range between 10µM and 7mM. The response of the PEC/AuNPs/GOD based biosensor also presents good reproducibility, stability and negligible interfering effects from ascorbic acid, uric acid, urea and creatinine. The applicability of the PEC/AuNPs/GOD based biosensor was tested in glucose-spiked saliva samples and acceptable recovery rates were obtained.

Polymers in highly confined geometries can display complex morphologies including ordered phases. A basic component of a theoretical analysis of their phase behavior in confined geometries is the knowledge of the number of possible single-chain conformations compatible with the geometrical restrictions and the established crystalline morphology. While the statistical properties of unrestricted self-avoiding random walks (SAWs) both on and off-lattice are very well known, the same is not true for SAWs in confined geometries. The purpose of this contribution is a) to enumerate the number of SAWs on the simple cubic (SC) and face-centered cubic (FCC) lattices under confinement for moderate SAW lengths, and b) to obtain an approximate expression for their behavior as a function of chain length, type of lattice, and degree of confinement. This information is an essential requirement for the understanding and prediction of entropy-driven phase transitions of model polymer chains under confinement. In addition, a simple geometric argument is presented that explains, to first order, the dependence of the number of restricted SAWs on the type of SAW origin.

We quantitatively investigated the statistical behaviors of semiflexible polymer chains, which are simultaneously subjected to force stretching and rectangular tube confinement. Based on the wormlike chain model and Odijk deflection theory, we derived a new deflection length, by which new compact formulas are obtained for the confinement free energy and force-confinement-extension relation. These newly derived formulas have been justified by numerical solutions of an eigenvalue problem associated with the Fokker-Planck governing equation and extensive Brownian dynamics simulations based on the so-called Generalized Bead-Rod (GBR) model. We found that, comparing to the classical deflection theory, these new formulas are valid for a much extended range of the confinement-size /persistence-length ratio, and have no adjustable fitting parameters for sufficient long semiflexible chains in the whole deflection regime.

Electrically conductive polymer composites are in high demand for modern technologies, however, the intrinsic brittleness of conducting conjugated polymers and the moderate electrical conductivity of engineering polymer/carbon composites have highly constrained their applications. In this work, super high electrical conductive polymer composites were produced by a novel hot embossing design. The polydimethylsiloxane (PDMS) composites containing short carbon fiber (SCF) exhibited an electrical percolation threshold at 0.45 wt%, and reached a saturated electrical conductivity of 49 S/m at 8 wt% of SCF. When reduced the sample thickness from 1.0 mm to 0.1 mm by the hot embossing process, a compression-induced percolation threshold occurred at 0.3 wt%, while the electrical conductivity was further enhanced to 378 S/m at 8 wt% SCF. Furthermore, the additional of a second nanofiller of 1 wt%, such as carbon nanotube or conducting carbon black further increased the electrical conductivity of the PDMS/SCF (8 wt%) composites to 909 S/m and 657 S/m, respectively. The synergy of the densified conducting filler network by the mechanical compression and the hierarchical micro-/nanoscale filler approach has realize super high electrical conductive yet mechanical flexible polymer composites for modern flexible electronics applications.

Three kinds of hydrophobic groups grafted starches of maleic anhydride grafted starch (MAH-g-starch), lactic acid grafted starch (LA-g-starch), and methyl acrylate grafted starch (MA-g-starch) were prepared by in-situ solid phase polymerization. The results of Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) were confirmed successful grafting. The grafting ratios of MAH-g-starch, LA-g-starch and MA-g-starch were 6.50%, 12.45%, and 0.57%, respectively. Influenced by the grafting ratio, LA-g-starch had the best hydrophobic properties and the largest molecular weight, and those for MA-g-starch was the worst. The surfaces of grafted starches were covered with graft polymer, with obvious surface roughness and bond degree of MAH-g-starch and LA-g-starch. The crystalline structure of grafted starches showed some damage, with LA-g-starch exhibiting the greatest decrease in crystallinity, and less of a change for MA-g-starch. Overall, the grafting reaction improved thermoplasticity, with LA-g-starch the most improved, followed by MAH-g-starch, and then MA-g-starch.

Evaluating new, promising organic molecules to make next-generation organic optoelectronic devices necessitates the evaluation of charge carrier transport performance through the semi-conducting medium. In this work, we utilize quantum chemical calculations (QCC) and kinetic Monte Carlo (KMC) simulations to predict the zero-field hole mobilities of ~100 morphologies of the benchmark polymer poly(3-hexylthiophene), with varying simulation volume, structural order, and chain-length polydispersity. Morphologies with monodisperse chains were generated previously using an optimized molecular dynamics force-field and represent a spectrum of nanostructured order. We discover that a combined consideration of backbone clustering and system-wide disorder arising from side-chain conformations are correlated with hole mobility. Furthermore, we show that strongly interconnected thiophene backbones are required for efficient charge transport. This definitively shows the role "tie-chains" play in enabling mobile charges in P3HT. By marrying QCC and KMC over multiple length- and time-scales, we demonstrate that it is now possible to routinely probe the relationship between molecular nanostructure and device performance.

In this work, nylon 6/ P(N-phenylmaleimide-alt-styrene) blends were prepared by melt blending, and the mechanical, heat-resistant, crystallographic and dynamical mechanical properties of nylon 6/ P(N-phenylmaleimide-alt-styrene) blends with different contents were investigated and analyzed. The results showed that the mechanical properties decreased with increasing PNS, while the heat deflection temperature (HDT), relative crystallinity (Xn), and storage modulus (G’) increased with increasing PNS. The results of differential Scanning Calorimetry (DSC) proved the PNS played the positive role of nucleating PA6. And the results of dynamic mechanical analysis (DMA) proved the PNS could improve the rigidity of PA6/PNS blends. From the SEM, these PNS domains were between 0.2 and 4 μm in diameter. The experimental results indicated that the addition of PNS improved the rigidity of PA6/PNS blends, and then improved the heat-resistant property.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

The article describes the study of the properties of polytetrafluoroethylene, modified using natural layered silicates—serpentinite. It is shown that the introduction of a small amount of layered silicates significantly increases the tribological characteristics of the material. The additional introduction of magnesium nano-spinels facilitated the formation of an intercalated polymer-silicate nanocomposite.

Fibre-reinforced composite structures under complex loads exhibit gradual damage behaviour with a degradation of effective mechanical properties and change of their structural dynamic behaviour. Damage manifests itself as spatial increase of inter-fibre failure and delamination-growth, resulting in local changes of stiffness. These changes affect not only the residual strengths but more importantly the structural dynamic behaviour. In case of composite rotors, this can lead to catastrophic failure if an eigenfrequency coincides with the rotational speed. The description and analysis of the gradual damage behaviour of composite rotors therefore provides the fundamentals for a better understanding of unpredicted structural phenomena. The gradual damage behaviour on the example of composite rotors and the resulting damage-dependent dynamic behaviour is experimentally investigated under propagating damage for combined out-of-plane and in-plane loads. A novel observation is reported, where monotonic increase of damage results in non-monotonic frequency shift of significant amount of eigenfrequencies.

Structural vibration induced by dynamic load or natural vibration is a nonnegligible factor in failure analysis. Based on vibrating boundary condition, impact resistance of shape memory alloy reinforced composites is investigated. In this investigation, modified Hashin’s failure criterion, Brinson’s model and visco-hyperelastic model are implemented into the numerical model to charactering the mechanical behavior of glass fiber/epoxy resin laminates, SMAs and interphase, respectively. First, fixed boundary condition is maintained in simulation to verify the accuracy of material parameters and procedures by comparing with experimental data. Then, a series of vibrating boundaries with different frequencies and amplitudes are applied during the simulation process to reveals the effect on impact resistances. The statistics of absorbed energy and contact force indicate that impact resistance of the composite under high frequency and large amplitude is lower than that under low frequency and small amplitude, and summarized by a mathematical expression.

We develop an optimized force-field for poly(3-hexylthiophene) (P3HT) and demonstrate its utility for predicting thermodynamic self-assembly. In particular, we consider short oligomer chains, model electrostatics and solvent implicitly, and coarsely model solvent evaporation. We quantify the performance of our model to determine what the optimal system sizes are for exploring self-assembly at combinations of state variables. We perform molecular dynamics simulations to predict the self-assembly of P3HT at ~350 combinations of temperature and solvent quality. Our structural calculations predict that the highest degrees of order are obtained with good solvents just below the melting temperature. We find our model produces the most accurate structural predictions to date, as measured by agreement with grazing incident X-ray scattering experiments.

Hybrid woven kenaf-carbon composite were fabricated in this study using epoxy resin as matrix. Effects of different fabric material namely weave designs (plain and satin) and fabric counts (5×5 and 6×6) on the properties of laminated woven kenaf polymer composite were evaluated. This study evaluates the mechanical and morphological properties of hybrid fabric kenaf-carbon from kenaf yarn of 500tex. Kenaf and carbon fabrics were used in this work, where vacuum infusion technique was selected to prepare the composite and epoxy resin was used as a matrix. The fibre weight content is 30% and four specimens were prepared for each samples and tested for their tensile, flexural, and impact strengths. The morphological properties of composites were analysed through the scanning electron microscope (SEM). The results revealed that plain woven fabric is favourable in terms of tensile and impact strengths compared to satin woven fabric. Meanwhile, 5×5 of fabric count gives better flexural modulus than composite fabricated with 6×6 fabric count. The morphologies of the fractured surface investigated by SEM demonstrated better adhesion properties and less fibre pull-out on plain woven fabric.

Fire behavior of natural rubber latex foam under different thickness conditions(d=1,2and 5cm)were explored though a little of experiments by using the self-built small scale experimental platform. It can be shown that the flame spread law of thermally thin and thermally thickness are different. Natural rubber latex foam with thickness of 2cm show higher fire risk, which value of flame spread rate, maximum flame height, maximum mass loss rate and maximum temperature is 0.00293m/s, 851.875mm, 1.83g/s, 948K,repectively.That may because the thickness of residue formed of thermally thick materials is larger than the thin one, obstructing the contact of the natural rubber latex foam with fresh air .In addition, a special phenomenon is noticed that during the second stage, the bottom unburned zone located in the four edges(thermally thin material) and middle player(thermally thick material).

Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

The recyclability of polystyrene, acrylonitrile butadiene styrene, polystyrene and polyvinylchloride waste and using them as a source for 3D printing were studied. Filaments of about 3 mm in diameter were extruded successfully with a small-size extruder. The processed filaments were tested on a broad range of parameters - glass transition temperature, tensile properties and a pyrolysis scenario were obtained. The measured parameters were compared with parameters of virgin counterparts presented in the literature. In order to estimate the toxicity of the recycled material, elemental analysis of the samples was done.

In this study is reported the optical, structural and dielectric properties of Poly (vinyl alcohol) thin films membranes with embedded ZnO nanoparticles (PVA/ZnO) obtained by solution casting method at low temperature of deposition. Fourier Transform Infrared spectra showed the characteristics peaks, which correspond to O-H and Zn-O bonds present in the hybrid material. The X-ray diffraction patterns indicated the presence of ZnO structure into the films. The composite material showed low absorbance and a wide band gap energy from 5.6 to 5.9 eV. The surface morphology for the thin films of PVA/ZnO was studied by Atomic Force Microscopy and Scanning Electron Microscopy. The dielectric properties of the nanocomposites were measured from low to high frequencies, the results showed a high dielectric constant (ε) in the order of 10⁴ at low frequency and values from ε ≈ 2000 to 100 in the range of 1KHz-1MHz respectively, the properties of PVA/ZnO such as the high permittivity and the low temperature of processing make it a suitable material for potential applications in the development of flexible electronic devices.

The possibility of using additive manufacturing (AM) in the medicine area has created a new opportunities in health care. This has contributed to a sharp increase in demand for 3D printers, their systems and materials that are adapted to strict medical requirements. We described herein a medical-grade thermoplastic polyurethane (S-TPU), which was developed and then formed into a filament for Fused Deposition Modeling (FDM) 3D printers during a melt-extrusion process. S-TPU consisting of aliphatic hexamethylene 1,6-diisocyanate (HDI), amorphous α,ω-dihydroxy(ethylene-butylene adipate) (PEBA) and 1,4 butandiol (BDO) as a chain extender, was synthesized without the use of a catalyst. The filament properties were characterized by rheological, mechanical, physico-chemical and in vitro biological properties. The tests showed biocompatibility of the obtained filament as well as revealed no significant effect of the filament formation process on its properties. This study may contribute to expanding the range of medical-grade flexible filaments for standard low-budget FDM printers.

Amine containing polymers are extensively studied as special carriers for short-chain RNA (13–25 nucleotides) which are applied as gene silencing agent in gene therapy of various diseases including cancer. Elaboration of the oligonucleotide carriers requires knowledge about peculiarities of oligonucleotide - polymeric amine interaction. Critical length of the interacting chains is the important parameter which allows to design sophisticated constructions containing oligonucleotide binding segments, solubilizing, protective and aiming parts. We studied interaction of (TCAG)n, n=1-6 DNA oligonucleotides with polyethylenimine and poly(N-(3-((3-(dimethyl­amino)propyl)(methyl)amino)propyl)-N-methylacrylamide). Critical length for oligonucleotides in interaction with polymeric amines is 8-12 units and complexation at these length can be accompanied by "all-or-nothing" effects. New dimethylacrylamide based polymers with grafted polyamine chains were obtained and studied in complexation with DNA and RNA oligonucleotides. The most effective interaction and transfection activity into A549 cancer cells was found for a sample with average number of nitrogens in polyamine chain equal to 27, i.e. for a sample in which all grafted chains are longer the critical length for polymeric amine - oligonucleotide complexation.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

Over the past decades, research has escalated on the use of polylactic acid (PLA) as replacement for petroleum-based polymers. This is due to its valuable properties, such as renewability, biodegradability, biocompatibility and good thermomechanical properties. Despite possessing good mechanical properties comparable to conventional petroleum-based polymers, PLA suffers from some shortcomings such as low thermal resistance, heat distortion temperature and rate of crystallization, thus different fillers have been used to overcome these limitations. In the frame work of environmentally friendly processes and products, there has been growing interest on the use of cellulose nanomaterials viz. cellulose nanocrystals (CNC) and nanofibers (CNF) as natural fillers for PLA towards advanced applications other than short-term packaging and biomedical. Cellulosic nanomaterials are renewable in nature, biodegradable, eco-friendless and they possess high strength and stiffness. In the case of eco-friendly processes, various conventional processing techniques, such as melt extrusion, melt-spinning, and compression moulding, have been used to produce PLA composites. This review addresses the critical factors in the manufacturing of PLA-cellulosic nanomaterials by using conventional techniques and recent advances needed to promote and improve the dispersion of the cellulosic nanomaterials. Different aspects, including morphology, mechanical behavior and thermal properties, as well as comparisons of CNC- and CNF reinforced PLA, are also discussed

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

In this present study, 3-pentadecyl-phenol was selected as a modifier to prepare a foamable phenolic resin with excellent performance, which was successfully prepared by in-situ modification. Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance (¹H NMR, ¹³C-NMR) were used to test and characterize the molecular structure of the modified resin. The results showed that 3-pentadecyl-phenol successfully modified the molecular structure of phenolic resin with a reduction in resin gel time. The effect of changing the added amount of 3-pentadecyl-phenol on the mechanical properties, microstructure and flame retardancy of the modified foam was investigated. The results showed that when the amount of added 3-pentadecyl-phenol was 15% of the total amount of phenol, this resulted in the best toughness of the modified foam, which could be increased to 300% compared to the bending deflection of the unmodified phenolic foam. The cell structure showed that the modified phenolic foam formed a more regular and dense network structure and the closed cell ratio was high. Furthermore, the compressive strength, bending strength, and limited oxygen index were improved, while the water absorption rate was lowered. However, the foam density could be kept below 40 mg/cm³, which does not affect the load.

In this paper, ground tire rubber (GTR) was mechano-chemically modified with road bitumen 160/220 and subsequently treated using a microwave radiation. The combined impact of bitumen 160/220 content and microwave treatment on short-term devulcanization of GTR were studied by thermal camera, wavelength dispersive X-ray fluorescence spectrometry (WD-XRF), static headspace and gas chromatography-mass spectrometry (SHS-GC-MS), thermogravimetric analysis combined with Fourier transform infrared spectroscopy (TGA-FTIR), oscillating disc rheometer and static mechanical properties measurements. The obtained results showed that bitumen plasticizer prevent oxidation of GTR during microwave treatment and simultaneously improves processing and thermal stability of obtained reclaimed rubber.

Simulation programs contain Computational Fluid Dynamics - CFD codes and are a useful tool used for gas flow through porous materials. Conducting numerical simulations allows for detailed analysis of hydrodynamic phenomena. The results of numerical modeling should always be verifiable based on experimental data. Only their compliance with the results of experimental tests is a determinant of the correctness of the applied method. As part of the work, experimental studies of hydrodynamics of gas flow through an isotropic porous material were carried out and numerical simulation for material of the same shape was used. In the CFD modeling Kolmogorov's hypothesis for the transport of kinetic energy of turbulence k and transport of dissipation rate of kinetic energy of turbulence ε was used.

The reinforcing ability of the fillers results in significant improvements in properties of polymer matrix at extremely low filler loadings compared to conventional fillers. In view of this, present review article describes the different methods used in preparation of different rubber nanocomposites reinforced with nanodimensional individual carbonaceous fillers, such as graphene, expanded graphite, single walled carbon nanotubes, multiwalled carbon nanotubes and graphite oxide, graphene oxide and hybrid fillers consisting combination of individual fillers. This is followed by review of mechanical properties (tensile strength, elongation at break, Young modulus, and fracture toughness) and dynamic mechanical properties (glass transition temperature, crystallization temperature, melting point) of these rubber nanocomposites. Finally, Payne and Mullin Effects have also been reviewed in rubber filled with different carbon based nanofillers.

Here, we present a series of novel block copolymers (BCP) from bio-derived monomers, poly(lactic acid)-block-poly(2,5-furandimethylene succinate) (PLA-b-PFS), in which the furan groups from PFS block can be crosslinked with bis(maleimido) triethylene glycol (M2) through a Diels-Alder reaction. This dynamic crosslinking reaction leads to a network structure for enhancing the mechanical properties compared to their linear BCP analogous. Decreasing the crosslinking density leads to a decrease of glass transition temperature of BCPs and a transition from glassy to rubbery-like behavior at room temperature. This allows a wide tunablity of both elastic moduli and yields of the materials. For the lowest crosslinking density. the material exhibits an over 50% self-healing efficiency at room temperature after five days, attributed to the low Tg (15.2 C) from the introduction of PFS block, allowing sufficient chain mobility for structure re-organization. Moreover, with the appropriate selection of crosslinking density (PLA-b-PFS/M2 (6/1)), it also shows an excellent shape memory property with a high recovery rate of 96.3% and a fixity rate of 97.3%. The permanent shape can be rewriteable due to the reversibility of Diels-Alder reaction. With these advanced functionalities and ease in large-scale fabrication, the PLA-b-PFS/M2 shows great promises for self-healing coatings or films with shape memory properties in a wide variety of applications such as packaging materials

Most of the phase change materials (PCMs) have been limited to use as functional additions or sealed in containers, and extra auxiliary equipment or supporting matrix is needed. The emergence of 3D printing technique has dramatically advanced the developments of materials and simplified production processes. This study focuses on a novel strategy to model thermal energy storage crystalline gels with three-dimensional architecture directly from liquid resin without supporting materials through light-induced polymerization 3D printing technique. A mask-projection stereolithography printer was used to measure the 3D printing test, and the printable characters of crystalline thermal energy storage P(SA-DMAA) gels with different molar ratios were evaluated. For the P(SA-DMMA) gels with small fraction of SA, the 3D fabrication was realized with higher printing precision both on mili- and micro-meter scales. As a comparison of 3D printed samples, P(SA-DMAA) gels made by other two methods, post-UV curing treatment after 3D printing and UV curing using conventional mold, were prepared. The 3D printed P(SA-DMAA) gels shown high crystallinity. Post–UV curing treatment was beneficial to full curing of 3D printed gels, but did not lead to the further improvement of crystal structure to get higher crystallinity. The P(SA-DMAA) crystalline gel having the highest energy storage enthalpy that reached 69.6 J·g⁻¹ was developed. Its good thermoregulation property in the temperature range from 25 to 40 °C was proved. The P(SA-DMAA) gels are feasible for practical applications as one kind of 3D printing material with thermal energy storage and thermoregulation functionality.

In this work we have investigated the role of various additives (emulsifier, anti-dripping agent) and formulation procedure (pre- dispersion of solid additives in polyol via milling) which influence the flame retardancy of 6,6′-[ethan-1,2-diylbis(azandiyl)]bis(6H-dibenzo[c,e][1,2]oxaphosphin-6-oxid) (EDA-DOPO) containing flexible polyurethane foams. For comparison, the flame retardancy of two additional structurally analogues bridged 9, 10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) based compounds i.e. ethanolamine-DOPO (ETA-DOPO) and ethylene glycol-DOPO (EG-DOPO) were also evaluated together with EDA-DOPO in flexible PU foams of various formulations. The flame retardancy of three bridged-DOPO compounds depends on the type of PU formulation. For certain PU formulation containing EDA-DOPO, lower fire performance was observed. Addition of emulsifier and polytetrafluoroethylene (PTFE) to these PU formulations influenced positively the flame retardancy of EDA-DOPO/PU foams. In addition, dispersion of EDA-DOPO and PTFE via milling in polyol improved the flame retardancy of the PU foams. Mechanistic studies performed using pyrolysis combustion flow calorimetry (PCFC) and its coupling to FTIR showed no difference in the combustion efficiency of the bridged-DOPO compounds in PU foams. From these PCFC experiments we can conclude that these bridged-DOPO compounds and their decomposition products may work primarily in the gas phase as flame inhibitors. Physiochemical behavior of additives in PU formulation responsible for the improvement in the flame retardancy of PU foams was further investigated by studying the dripping behavior of the PU foams in UL 94 HB test. A high-speed camera was used to study the dripping behavior in the UL 94 HB test and results indicate a considerable reduction of a total number of melt drips and flaming drips for the flame retardant formulations. This reduction in melt drips and flaming drips during the UL 94 HB tests help PU foams achieve higher fire classification.

Free volume is an extremely important intrinsic defect in polymers. Structurally, the free volume is the randomly distributed holes in the polymer molecular chain segments. From the perspective of molecular movement, it is also the space needed for the movement of molecular segments. In proton exchange membrane fuel cells, the free volume is also the space needed for the directional conduction of protons. Irradiation grafting sulfonated polyvinylidene fluoride (PVDF) is one of the methods to produce proton exchange membrane with good proton channel rate. Using the LYS-1 program, based on the linear absorption coefficient and backscatter coefficient models, the percentage of annihilated positrons in PVDF in the two-layer model and the three-layer model was studied, and comparing the two fitting results it is determined that the model closest to the positron annihilation percentage required by the PALS experiment is the two-layer model, which allows the percentage of positrons that are annihilated in PVDF films with a thickness of 100 μm to reach 46% using the high energy positron source ⁴⁴Ti without using the positron moderator. Using positron annihilation lifetime spectrum (PALS) analysis methods, based on Eldrup's classical model of free volume, the influence of absorbed doses of α particles on the free volume and crystallinity of PVDF was investigated, respectively. Based on the two test results the model of cross-linking and degradation of polyvinylidene fluoride irradiated by α particles was determined. Afterwards, X-ray diffraction (XRD) methods was used to study the change of PVDF crystal area before and after irradiation. The XRD results are consistent with the results measured by PALS.

Water pollution in developing countries affects the public health of humans and the environment. It is therefore essential to develop environmentally friendly biopolymer, sustainable and low-cost membranes. Biopolymer nanofiber membranes are made by an electrospinning process of polylactic acid (PLLA) with additives. The main objective of this study is to manufacture biodegradable nanofiber membranes for use in filtering the suspended elements in wastewater at the level of drinkable or in agricultural fields. It is known that PLLA is brittle and therefore it is difficult to apply in industry. To solve this problem and enhance its flexibility. Flexible biopolymer polypropylene carbonate (PPC) and plasticizer are the addition in PLLA to reduce its glass transition and enhance its crystallization by adding Poly(3-hydroxy butyrate) PHB. In this work, 20 wt% of PPC was added to PLLA matrix to improve its elasticity and elongation at break. DSC shows that the addition of PPC, PHB, and TEC did affect the thermal properties like T_g, T_cc and T_m of the PLLA blends. The position of the T_g, T_cc, and T_m is shifting, the consequence the chain mobility is increased, therefore the crystallinity is enhanced. Electrospun fibers of PLLA/PPC/PHB/TEC were successfully manufactured. Tensile tester showed the increase in elongation at break of PLLA blend films, the elongation at break increases by 285 times. It observed with the increasing the elongation at break, a decrease in stress strength. After improving the mechanical properties with the higher elongation at break values, this blend is optimal for filtrations process.

Lightning strike can cause a considerable damage in aircraft parts made from semiconducting materials such as Carbon Fiber Reinforced Plastics (CFRPs). Therefore, in recent years, the lightning strike phenomenon has attracted the interest of the academic community and the aircraft industry. Until now, the problem has been addressed mainly experimentally, while the reported numerical works are very limited. In the present work, a coupled electro-thermal FE model has been developed using the ANSYS commercial FE code to simulate the lightning strike damage in unidirectional CFRP laminates due to the Joule heat flux phenomenon. The model is based on the SOLID69 thermoelectric element and applies a non-linear, time-transient analysis. The main input to the model is the thermal-electrical properties of the composite material which vary with temperature. Using the model, a parametric study on the effect of mesh density and peak intensity on the thermal damage has been performed. Three electrical lightning strikes of low (10 kA), medium (30 kA) and high peak intensity (40 kA) have been applied according to the SAE ARP 5412 standard. The electro-thermal model has been validated against a numerical model from the literature. The numerical results reveal that the increase of peak intensity leads to the increase of the area and penetration depth of matrix thermal damage (pyrolysis) as well as to the increase of the area of fiber damage (deterioration and ablation). Through progressive damage modeling, the residual tensile strength of the CFRP plate after being subjected to lightning strike of different peak intensity has been predicted. Lightning strike initial damage has been simulated by translating the thermal field into degradation of elastic properties of the lamina. The results show an increase in the accumulated matrix damage and a decrease of tensile strength due to the initial lightning strike damage. For the maximum peak intensity of 40 kA, a decrease in tensile strength of 4.8% has been predicted

This article discusses the results of a series of experiments on pulse ultrasonic cure monitoring of carbon fiber reinforced plastics applied to the pultrusion process. The aim of this study is to validate the hypothesis that pulse ultrasonic cure monitoring can be applied a) for profiles having small cross sections such as 7x0.5 mm and b) within the environment of the pultrusion process. Ultrasonic transducers are adhesively bonded to the pultrusion tool as actuators and sensors. The time-of-flight and the amplitude of an ultrasonic wave are analyzed to deduce the current curing state of the epoxy matrix. The experimental results show that ultrasonic cure monitoring is indeed applicable even to very thin cross sections. However, significant challenges can be reported when the techniques are used during the pultrusion process.

Polyurethane (PU) foam adhesives were prepared from castor oil as a polyol with isocyanate poly (4,4′-methylene diphenyl isocyanate) (PMDI) using a solvent-free process. The NCO/OH molar ratio used for the preparation of PU foams was 1.5. Water, organosiloxane and dibutyltin dilaurate were blowing agent, surfactant and catalyst, respectively. Effects of the ratio of blowing agent and catalyst were adjusted to optimize the properties. The results show that 4 wt% of castor oil of catalyst and blowing agent minimizes water absorption and maximizes volume expansion in the PU foams. FT-IR analysis shows that urethane bond was formed by hydroxyl group of castor oil and –NCO group of isocyanate PMDI. More blowing agent and catalyst could improve the volume expansion ratio and reduce water retention of PU foams. It was found that Moso bamboo charcoal (Phyllostachys pubescens) or/and China fir wood particle (Cunninghamia lanceolate) composites with setting densities of 500 and 600 kg/m³ can be prepared from optimized castor oil-based PU foam adhesive at 100 °C for 5 min under a pressure of 1.5 MPa. Increasing the amount of bamboo charcoal decreases the equilibrium moisture content, water absorption and internal bonding strength of the composite. Notably, bamboo charcoal composite exhibits excellent dimensional stability. The optimized density and bamboo charcoal percentages of the composite were 500 kg/m³ and 50 to 100%. The castor oil-based PU composites containing bamboo charcoal fulfilled the CNS 2215 standards for particleboard. This dimensionally stable, low-density bamboo charcoal composite has high potential to replace current indoor building materials.

The effect of hybrid carbon fillers of multi-walled carbon nanotubes (CNT) and carbon black (CB) on the electrical and morphological properties of polystyrene (PS) nanocomposites were systematically investigated in microinjection molding (μIM). The polymer nanocomposites with three different filler concentrations (i.e. 3, 5 and 10 wt%) at various weight ratios of CNT/CB (100/0, 30/70, 50/50, 70/30, 0/100) were prepared by melt blending, then followed by μIM under a defined set of processing conditions. A rectangular mold insert which has three consecutive zones with decreasing thickness along the flow direction was adopted to study abrupt changes in mold geometry on the properties of resultant microparts. The distribution of carbon fillers within microparts was observed by scanning electron microscope, which was correlated with electrical conductivity measurements. Results indicated that there is a flow-induced orientation of incorporated carbon fillers and this orientation increased with increasing shearing effect along the flow direction. High structure CB is found to be more effective than CNT in terms of enhancing the electrical conductivity, which was attributed to the good dispersion of CB in PS and their ability to form conductive networks via self-assembly. Morphology observations indicated that there is a shear-induced depletion of CB particles in the shear layer, which is due to the marked difference of shear rates between the shear and core layers of the molded microparts. Moreover, an annealing treatment is beneficial to enhance the electrical conductivity of CNT-containing microparts.

Abstract: We have filled a 24 mm diameter glass sphere with a transparent polymer-gel that is radio-fluorogenic, i.e. it becomes (permanently) fluorescent when irradiated, with an intensity proportional to the local dose deposited. The gel consists of >99.9% tertiary-butyl acrylate (TBA) pre-polymerized to ~15% conversion, and ~100 ppm maleimido-pyrene (MPy). Its dimensions and physical properties are close to those of the vitreous body of the human eye. We have irradiated the gel with a 3 mm diameter, 200 kVp X-ray beam with a dose rate of ~1 Gy/min. A 3D (video) view of the beam within the gel has been constructed from tomographic images obtained by scanning the sample through a thin sheet of UV light. To minimize optical artifacts, the cell was immersed in a square tank containing a refractive-index-matching medium. The 20%-80% penumbra of the beam was determined to be ~0.4 mm. The research was a preparatory investigation of the possibility of using the method to monitor the millimetre diameter proton pencil beams used in ocular radiotherapy.

Bamboo plastic composites have become a hot research topic and a key focus of research. However, the many strong, polar, hydrophilic hydroxyl groups in bamboo flour (BF) results in poor interfacial compatibility between BF and hydrophobic polymers. Maleic anhydride-esterified (MAH-e-BF) and lactic acid-esterified bamboo flour (LA-e-BF) were prepared using an in situ solid-phase esterification method with BF as the raw material and maleic anhydride or lactic acid as the esterifying agent. Fourier transform infrared spectroscopy results confirmed that BF esterification with maleic anhydride and lactic acid was successful, with the esterification degrees of MAH-e-BF and LA-e-BF at 21.04 and 14.36%%, respectively. Esterified BF was characterized by scanning electron microscopy, contact angle testing, X-ray diffractometry, and thermogravimetric analysis. The results demonstrated that esterified BF surfaces were covered with graft polymer and the surface roughness and bonding degree of MAH-e-BF clearly larger than those of LA-e-BF. The hydrophobicity of esterified BF was significantly higher than BF and the hydrophobicity of MAH-e-BF better than LA-e-BF. The crystalline structure of esterified BF showed some damage, with MAH-e-BF exhibiting a greater decrease in crystallinity than LA-e-BF. Overall, the esterification reaction improved BF thermoplasticity, with the thermoplasticity of MAH-e-BF appearing better than LA-e-BF.

The capacity of 3D printing (3DP) technologies to initiate speedy polymerization of solvent free resins accounts for their utility in the manufacturing of medical devices. Nonetheless, independent biological evaluation of 3D printed materials is recommended due to the unique parameters of the manufacturing process, which can influence their physical, chemical, and biological properties. In this study, E-Shell 450 material indicated for 3DP of hearing aid shells and inner ear devices was examined for biological safety using zebrafish bioassays adapted to OECD fish embryo test. In addition, the proprietary material was characterized for composition using headspace gas-chromatography mass spectrometry (GC-MS). To initiate test, newly fertilized zebrafish eggs were cultured on non-treated and ethanol-treated materials in glass petri dishes with ultrapure water, incubated at 28.5°C and assessed for developmental endpoints of toxicity at 24h interval until 96h. Data confirmed non-treated material was extremely toxic in bioassays within 24h whereas ethanol-treated material showed a relative lower toxicity possibly due to ethanoic-aqueous interactions as observed by GC-MS. With the current influx of 3D printing materials, users are urged to exercise caution. Operators must also take cognizance of the potential toxicity of the chemicals used in 3DP and implement safety measures to limit their exposure.

High porosity and mass transport properties of microfiltration polymeric membranes benefits nutrients supply to cells when used as scaffolds in interstitial perfusion bioreactors for tissue engineering. High nutrients transport is assumed when pore size and porosity of the membrane are in the micrometric range. The present work demonstrates that the study of membrane fouling by proteins present in the culture medium, though not done usually, should be included in the routine testing of new polymer membranes for this intended application. Two poly(ε-caprolactone) microfiltration membranes presenting similar average pore size (~0.7µm) and porosity (>80%) but different external surface porosity and pore size have been selected as case study. The present work demonstrates that a membrane with lower surface pore abundance and smaller external pore size (~0.67 µm), combined with adequate hydrodynamics and tangential flow filtration mode is usually more convenient to guarantee high flux of nutrients. On the contrary, having large external pore size (~1.70µm) and surface porosity would incur in important internal protein fouling that could not been prevented with the operation mode and hydrodynamics of the perfusion system. Additionally, the use of glycerol in the drying protocols of the membranes might cause plasticization and a consequent reduction of mass transport properties due to membrane compaction by the pressure exerted to force perfusion. Therefore, preferentially, drying protocols that omit the use of plasticizing agents are recommended.

Electrospun nanofiber-supported thin film composite membranes are among the most promising membranes for seawater desalination via forward osmosis. In this study, a high-performance electrospun polyvinylidenefluoride (PVDF) nanofiber-supported TFC membrane was successfully fabricated after molecular layer-by-layer polyelectrolyte deposition. Negatively-charged electrospun polyacrylic acid (PAA) nanofibers were deposited on electrospun PVDF nanofibers to form a support layer consisted of PVDF and PAA nanofibers. This resulted to a more hydrophilic support compared to the plain PVDF nanofiber support. The PVDF-PAA nanofiber support then underwent a layer-by-layer deposition of polyethylenimine (PEI) and PAA to form a polyelectrolyte layer on the nanofiber surface prior to interfacial polymerization, which forms the selective polyamide layer of TFC membranes. The resultant PVDF-LbL TFC membrane exhibited enhanced hydrophilicity and porosity, without sacrificing mechanical strength. As a result, it showed high pure water permeability and low structural parameter values of 4.12 Lm⁻²h⁻¹bar⁻¹ and 221 µm, respectively, significantly better compared to commercial FO membrane. Layer-by-layer deposition of polyelectrolyte is therefore a useful and practical modification method for fabrication of high performance nanofiber-supported TFC membrane.

Herein, we present preparation of solid polymer electrolyte (SPE) comprising of PEO, NaPF₆ and varying fraction of Succinonitrile (SN) by standard solution cast technique. The morphological features and structural properties were studied by the FESEM, XRD, respectively. FTIR was performed to study the interactions between polymer host, salt, and SN. Impedance spectroscopy, Transference number measurements, LSV and CV were used to examine the electrochemical properties. The complex permittivity/conductivity & modulus were studied to understand the dielectric properties by evaluating the dielectric strength, relaxation time, hopping frequency and dc conductivity. Based on the experimental results an interaction mechanism is presented.

In this paper, an icosahedral non – body centered model to simulate the periodic structure of homogeneous particulate composites, by predicting the particle arrangement, is presented. This model has yielded three different variations which correspond at three different deterministic particle configurations. In addition, the concept of boundary interphase between matrix and inclusions was taken into account. Thus, the influence of particle vicinity was examined in parallel with the interphase concept on the thermomechanical properties of the overall material. Next, by the use of this model the authors derived a closed – form expression to estimate the thermal conductivity of this type of composites. To test the validity of the model, the theoretical values arising from the proposed formula were compared with other theoretical predictions obtained from several accurate formulae found in the literature and an adequate accordance was observed.

Polyurethanes are materials with a strong structure-property relationship. The goal of this research was to study the effect of a polyol blend composition of polyurethanes on its properties using a mixture design and setting mathematic models for each property. Water absorption, hydrolytic degradation, contact angle, tensile stretch, hardness and modulus were studied. Additionally, Thermal stability was studied by thermogravimetric analysis. Area under the curve was used to evaluate the effect of polyol blend composition on thermal stability and kinetics of water absorption and hydrolytic degradation. Least squares were used to calculate the regression coefficients. Models for the properties were significant, and lack of fit was not (P<0.05). Fit statistics suggest both good fitting and prediction. Water absorption, hydrolytic degradation and contact angle were mediated by the hydrophilic nature of the polyols. Tensile strength, modulus and hardness could be regulated by the molecular weight and hydroxyl index of the polyols. Regression of DTG curves from thermal analysis showed improvement of thermal stability with the increase of PCL and PE. An ANOVA test of the model terms demonstrated that three component effects on bulk properties like water absorption, hydrolytic degradation, hardness, tensile strength and modulus, and the PEG*PCL interaction with the contact angle, which is a surface property. Mixture design application allowed for an understanding of the structure-property relationship through mathematic models.

The separator membrane is an essential component of lithium-ion batteries, separating the anode and cathode and controlling the number and mobility of the lithium ions. Among the polymer matrices most investigated for battery separators are poly(vinylidene fluoride) (PVDF) and its copolymers poly(vinylidene fluoride-co-trifluoroethylene) (PVDF-TrFE), poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), and poly(vinylidene fluoride-cochlorotrifluoroethylene) (PVDF-CTFE), due to their excellent properties such as high polarity and the possibility of controlling the porosity of the materials through binary and ternary polymer/solvent systems, among others. This review presents the recent advances on battery separators based on poly(vinylidene fluoride) (PVDF) and its copolymers for lithium-ion batteries. It is divided in the following sections: single polymer and co-polymers, surface modification, composites and polymer blends. Further, a critical comparison between those membranes and other separator membranes is presented, as well as the future trends on this area.

Decomposition of natural and synthetic polymeric materials (peat, humates, biochar, strongly swelling hydrogels and other soil conditioners) in a biologically- and chemically- active soil environment inevitably leads to their degradation and ability to improve the structure, water-retention, absorptive capacity and actual fertility of artificial soil constructions in urbanized ecosystems and agro landscapes (constructozems). Quantitative assessment of the biodegradation process using field and laboratory incubation experiments, as well as mathematical modeling, showed the possibility of significant (up to 30-50% per year) losses of organic matter of constructozems and a corresponding deterioration in their quality. Incubation experiments with the analysis of carbon dioxide emission for polymeric materials under given thermodynamic conditions allow to estimate the potential rates of their decomposition (half-life) and their dependence on the dose of inhibitors of microbial activity. Special nomographs provide an opportunity to determine the optimum depth of the arrangement of organic components in soil constructions to ensure their stable functioning during a fixed operating time in urban conditions. The results of the study are useful for geo-engineers and landscaping practitioners.

We investigated the structural evolution of the two-phase blends of polycarbonate (PC) and poly(methyl methacrylate) (PMMA) at various blend compositions by simultaneous biaxial stretching using optical microscopy and SEM observation. The spherical PMMA domains and PC matrix in 30/70 PC/PMMA were enlarged uniformly at all in-plane direction, while the anisotropic-shaped co-continuous structure in 50/50 PC/PMMA was deformed to crosshatched one by in-plane bimodal orientation. In 70/30 PC/PMMA, the phase inversion was found to occur by simultaneous biaxial stretching; i.e., the spherical PMMA domains were changed to crosshatched matrix by in-plane bimodal orientation due to coalescence of the PMMA domains during the stretching. Owing to the phase inversion, the surface hardness estimated by pencil hardness test became harder from 2B to 2H with increasing the strain from 1.0 to 2.0.

Abstract: We review the development and application of an organic polymer-gel capable of producing fixed, three-dimensional fluorescent images of complex radiation fields. The gel consists for more than 99% of γ-ray-polymerized (~15% conversion) tertiary-butyl acrylate (TBA) containing ~100 ppm of a fluorogenic compound, e.g. maleimido-pyrene (MPy). The radio-fluorogenic effect depends on copolymerization of the MPy into growing chains of TBA on radiation-induced polymerization. This converts the maleimido residue, which quenches the pyrene fluorescence, into a succinimido moeity (SPy), which doesn't. The intensity of the fluorescence is proportional to the yield of free-radicals formed and hence to the local dose deposited. Because the SPy moieties are built into the cross-linked polymer matrix the image is fixed. The method of preparing the gel and imaging the radiation-induced fluorescence are presented and discussed. The effect is illustrated with fluorescent images of the energy deposited in the gel by beams of X-rays, electrons and protons as well as a radioactive isotope.

The kinetics and optimal efficacy conditions of photoinitiated polymerization are theoretically presented. Analytic formulas are derived for the crosslink time, crosslink depth and efficacy function. The roles of photosensitizer (PS) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented . For optimal efficacy, a strategy via controlled PS concentration is proposed, where re-supply of PS in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced.

Solvent-free, single-ion conducting electrolytes are sought after for use in electrochemical energy storage devices. Here, we investigate the ionic conductivity and how this property is influenced by segmental mobility and conducting ion number in crosslinked single-ion conducting polyether-based electrolytes with varying tethered anion and counter-cation types. Crosslinked electrolytes are prepared by the polymerization of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) methyl ether acrylate, and ionic monomers. The ionic conductivity of the electrolytes is measured and interpreted in the context of differential scanning calorimetry and Raman spectroscopy measurements. A lithiated crosslinked electrolyte prepared with PEG₃₁DA and STFSI monomers is found to have a lithium ion conductivity of 3.2 × 10^-6 and 1.8 × 10⁻⁵ S/cm at 55 and 100 °C, respectively. The percentage of unpaired anions for this electrolyte was estimated at about 23% via Raman spectroscopy. Despite the large variances in metal cation – STFSI binding energies as predicted via DFT and large variations in ionic conductivity, STFSI-based crosslinked electrolytes with the same charge density and varying cations (Li, Na, K, Mg, and Ca) were estimated to all have unpaired anion populations in the range of 19 to 29%.

Aiming to improve the flame retardancy performance of natural rubber (NR), we developed a novel flame retardant synergistic agent through grafting of MCM-41 to graphene oxide (GO)，named as GO-NH-MCM-41，as an assistant of intumescent flame retardants (IFR). The structure of GO-NH-MCM-41 was characterized by FTIR, TEM and SEM tests, which confirmed that a fine grafting had been applied between GO and MCM-41. The flame retardancy of NR/IFR/GO-NH-MCM-41 composites was evaluated by limited oxygen index (LOI), UL-94 and cone calorimeter test. The LOI value of NR/IFR/GO-NH-MCM-41 reached to 26.3%; the UL-94 ratings improved to V-0 rating. Moreover, the addition of GO-NH-MCM-41 obviously decreased the peak heat release rate (PHRR) and the total heat release (THR) of the natural rubber composites. And the addition of GO-NH-MCM-41 increased the thickness of char residue. The images of SEM indicated the char residue were more compact and continuous. The degradation of GO-NH-MCM-41 based NR composites completed with a mass loss of 35.57% at 600 ℃. The tensile strength and the elongation at break of NR/IFR/GO-NH-MCM-41 composites were 13.9 MPa and 496.7%, respectively. The results of rubber process analyzer (RPA) reached the maximum value, probably due to a better network of the fillers in the matrix.

Metamaterials, man-made composites scaled smaller than the wavelength, have demonstrated a huge potential in their applications in acoustics, opening up for sub--wavelength acoustic absorbers, acoustic invisibility, perfect acoustic mirrors and acoustic lenses for hyper focusing, acoustic illusions and enabling new degrees of freedom in the control of the acoustic field. The zero, or even negative, refractive sound index of metamaterials offers possibilities in control of the acoustic pattern and sound at sub--wavelength scales. Despite the tremendous growth of the research on acoustic metamaterials during the last decade, the potential of metamaterial-based technologies in aeronautics is still not fully explored and its utilization is still in its infancy. Thus the principal concepts mentioned above could very well provide means to develop devices that would allow the mitigation of the impact of the civil aviation noise on the community. This paper gives a review of the state of the art of the most relevant works on acoustic metamaterials, analyzing them against their potential applicability in aeronautics, and in this process identifying possible implementation areas and interesting metabehaviors. It also identifies some technical challenges and possible future directions for research with the goal of unveiling the potential of metamaterials technologies in aeronautics.

An immiscible blend of poly(hydroxy ether of bisphenol-A) (phenoxy) and poly(1,4-butylene terephthalate) (PBT) with phase separation was observed in as-blended samples. However, compatibilization of the phenoxy/PBT blends can be promoted through chemical exchange reactions of phenoxy with PBT upon annealing. In contrast to the as-blended samples, the annealed phenoxy/PBT blends had a homogeneous phase with a single T_g that could be enhanced by annealing at 260°C. Infrared (IR) spectroscopy demonstrated that phase homogenization could be promoted by annealing of the phenoxy/PBT blend, where alcoholytic exchange occurred between the dangling hydroxyl group in phenoxy and the carbonyl group in PBT in the heated blends. The alcoholysis reaction changes the aromatic linkages to aliphatic linkages in carbonyl groups, which initially led to the formation of a graft copolymer of phenoxy and PBT with an aliphatic/aliphatic carbonyl link. The progressive alcoholysis reaction resulted in the transformation of the initial homopolymers into block copolymers and finally into random copolymers, which promoted phase compatibilization in blends of phenoxy with PBT. Due to the fact that the amount of copolymers increased upon annealing, crystallization of PBT was inhibited by alcoholytic exchange in the blends.

In this paper, an upper bound of the longitudinal elastic modulus of unidirectional fibrous composites is proposed according to strength of materials approach, on the premise that the fiber is much stiffer than the matrix. In the mathematical derivations, the concept of boundary interphase between fiber and matrix was also taken into account and the main objective of this work is the attainment of an upper bound for the interphase stiffness with respect to fiber concentration by volume. The novel element here is that the authors have not taken into consideration any specific variation law to approximate the interphase modulus. The theoretical results arising from the proposed formula were compared with those obtained from some reliable theoretical models as well as with experimental data found in the literature, and a satisfactory agreement was observed.

Resides derived from liquefaction of oil palm trunk in the presence of polyhydric alcohol with different liquefaction temperature and time were characterized to provide a new approach to understand some fundamental aspects of the liquefaction reaction. Higher temperature and longer reaction time resulted in lower residue content, indicating more decomposition of components of oil palm trunk. The amorphous polymer comprised of lignin, hemicellulose, starch, and cellulose with non-crystalline structure are firstly degraded at low liquefaction temperature, followed by the decomposition of crystalline region of cellulose. Although it was relatively difficult to destroy the ordered structure of cellulose, most of them could be liquefied via prolonging reaction time or enhancing reaction temperature. Nevertheless, it was found that re-condensation of liquefied products occurred during the liquefaction process when higher temperature of 180 oC was used after 60 min, leading to the gradual increase of residue content with increase of reaction time.

The Aminofunctional starch/Carboxylated nitrile butadiene rubber (ANS/XNBR) latex films were prepared with control (0), 5, 10, 15, and 20 phr of ANS loadings. The films were subjected to soil burial test for 8 weeks, which recovered every two weeks to quantify the degraded properties. The control (week 0) and biodegraded films were subjected to physical tests (crosslink density, tensile, and tear strength tests) and biodegradation quantification (mass loss retention, and water vapor transmission rates). The optimum physical properties of ANS/XNBR films were subjected to further assessment of its degradation properties which include morphological (optical and scanning electron microscopes (SEM)), Fourier transform infrared (FTIR) analysis, and thermogravimetric analysis (TGA) respectively. Overall, mechanical properties of biodegraded ANS/XNBR latex films decreased as biodegradation period elapses. The biodegradation assessment via water vapor transmission rates and mass loss analyses indicates the high degree of biodegradation rates were observed with higher loading of ANS/XNBR latex films. Morphological analyses via optical microscope shows the transformation of the films surface opacity during biodegradation test. SEM images depicted the microorganism remains on the film surfaces. For FTIR analysis, the most significant changes in the spectras of the films appeared in the region of 790–3000 cm⁻¹. TGA thermograph shows the thermal retention of the materials decreased, as the biodegradation period elapses for optimum ANS/XNBR latex films. From the results obtained, ANS/XNBR latex films shows optimum degradation and mechanical properties at 10 phr filler loading.

Furfuryl alcohol (FA) is a biobased monomer derived from lignocellulosic biomass. The present work describes its polymerization in presence of protic polar solvents, i.e. water or isopropyl alcohol (IPA), using maleic anhydride (MA) as acidic initiator. The polymerization was followed from the liquid to the rubbery state by combining DSC and DMA data. In the liquid state, IPA disrupts the expected reactions during all the FA polymerization due to a stabilization of the furfuryl carbenium center. This causes the initiation of the polymerization at higher temperature, which is also reflected by higher activation energy. In water system, the MA opening allows to start the reaction at lower temperature. A higher pre-exponential factor value is obtained in that case. The DMA study of final branching reaction occurring in the rubbery state has highlighted continuous increase of elastic modulus until 290 °C. This increasing tendency of modulus was exploited to obtain activation energy dependences (Eα) of FA polymerization in the rubbery state.

Engineering of drug nanocarriers combining fine-tuned mucoadhesive/mucopenetrating properties is currently being investigated to ensure more efficient mucosal drug delivery. Aiming to improve the transmucosal delivery of hydrophobic drugs, we designed a novel kind nanogel produced by the self-assembly of amphiphilic chitosan graft copolymers ionotropically crosslinked with sodium tripolyphosphate. In this work, we synthesized for the first time chitosan-g-poly(methyl methacrylate) nanoparticles thiolated by the conjugation of N-acetyl cysteine. First, we confirmed that both non-crosslinked and crosslinked nanoparticles in the 0.05-0.1% w/v concentration range display very good cell compatibility in two cell lines that are relevant to oral delivery, Caco2 cells that mimic the intestinal epithelium and HT29-MTX cells that produce mucin. Then, we evaluated the effect of crosslinking, nanoparticle concentration and thiolation on the permeability in vitro utilizing monolayers of (i) Caco2 and (ii) Caco2:HT29-MTX cells (9:1 cell number ratio). Results confirmed that the ability of the nanoparticles to cross Caco2 monolayer was affected by the crosslinking. In addition, thiolated nanoparticles interact more strongly with mucin, resulting in a decrease of the apparent permeability coefficient (Papp) compared to the pristine nanoparticles. Moreover, for all the nanoparticles, higher concentration resulted in lower Papp suggesting indicating that the transport pathways could undergo saturation.

A composite flocculant P(AM–DMDAAC) was synthesized by the copolymerization of acrylamide (AM) and dimethyl diallyl ammonium chloride (DMDAAC). Using microwave (MV) assistance with ammonium persulfate as initiator, the synthesis provided short reaction time and better solubility product. Nuclear magnetic resonance spectroscopy (1H NMR and 13C NMR), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and differential thermal analysis-thermo gravimetric analyzer (DTA-TGA) were used to determine the structure and morphology of P(AM–DMDAAC). Parameters affecting the intrinsic viscosity ([η]) of P(AM–DMDAAC), such as microwave time, mass ratio of DMDAAC to AM, initiator ammonium persulfatedosage, sodium benzoate dosage, bath time, reaction temperature and pH value were examined. Results showed that the optimum synthesis conditions were microwave time 1.5 min, m(DMDAAC): m(AM) is 4:16, 0.5 wt‰ initiator, 0.4 wt‰ EDTA, 0.3 wt‰ sodium benzoate, 2 wt‰ urea, 4 h bath time, 4.0h reaction time and pH 2. To study the removal of phenol by P(AM–DMDAAC), the influence of flocculant dose, pH value and the stirring speed were investigated, with optimization providing 99.8 % removal.

Reactive energetic plasticizers (REPs) coupled with hydroxy-telechelic poly(glycidyl azide-co-tetrahydrofuran) (PGT)-based energetic polyurethane (PU) binders for use in solid propellants and plastic-bonded explosives (PBXs) were investigated. The generation of gem-dinitro REPs along with a terminal alkyne stemmed from a series of finely designed approaches to not only satisfy the common demands as conventional energetic plasticizers but prevent the migration of plasticizers. The miscibility and rheological behavior of a binary mixture of PGT/REP with various REP fractions were quantitatively determined by differential scanning calorimetry (DSC) and rheometer, respectively, highlighting the promising performance of REPs in the formulation process. The kinetics on the distinct reactivity of propargyl vs. 3-butynyl species of REPs towards the azide group of the PGT prepolymer in terms of Cu-free azide-alkyne 1,3-dipolar cycloaddition (1,3-DPCA) was studied by monitoring 1H nuclear magnetic resonance spectroscopy and analyzing the activation energies (Ea) obtained using DSC. The thermal stability of the finally cured energetic binders with the incorporation of REPs indicated that the thermal stability of the REP/PGT-based PUs was maintained independently of the REP content. The tensile strength and modulus of the PUs increased with increasing the REP content. In addition, the energetic performance and sensitivity of REP and REP triazole species was predicted.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

Herein, we introduce a boron nitride nanosheet (BNNS)-reinforced cellulose nanofiber (CNF) film as a sustainable oxygen barrier film that can potentially be applied in food packaging. Most of commodity plastics are oxygen-permeable. CNF exhibits an ideal oxygen transmittance rate (OTR) of <1 cc/m²/day in highly controlled conditions. A CNF film typically fabricated by the air drying of a CNF aqueous solution reveals an OTR of 19.08 cc/m²/day. The addition of 0-5 wt% BNNS to the CNF dispersion before drying results in a composite film with highly improved OTR, 4.7 cc/m²/day, which is sufficient for meat and cheese packaging. BNNS as a 2D nanomaterial increases the pathway of oxygen gas and reduces the chances of pin-hole formation during film fabrication involving water drying. In addition, BNNS improves the mechanical properties of the CNF films (Young’s modulus and tensile strength) without significant elongation reductions, probably due to the good miscibility of CNF and BNNS in the aqueous solution. BNNS addition also produces negligible color change, which is important for film aesthetics. An in vitro cell experiment was performed to reveal the low cytotoxicity of the CNF/BNNS composite. This composite film has great potential as a sustainable high-performance food packaging material.

Poly(2,6-dimethyl phenyl oxide) (PPO) is known for its low dissipation factor. To achieve insulating materials with low dissipation factor for high-frequency communication application, a monomer-type benzoxazine (P-APPO) and a main-chain-type benzoxazine (BPA-APPO) were prepared from an amine end-capped oligo (2,6-dimethyl phenylene oxide) (APPO). The APPO was prepared from a nucleophilic substitution of a phenol-end capped oligo (2,6-dimethyl phenylene oxide) (a commercial product, SA 90) with fluoronitrobenzene, and followed by catalytic hydrogenation. After self-curing or curing with a dicyclopentadiene-phenol epoxy (HP 7200), thermosets with high-T_g and low-dissipation factor can be achieved. Furthermore, the resulting epoxy thermosets show better thermal and dielectric properties than those of epoxy thermoset cured from its precursor SA90, demonstrating it is a successful modification in simultaneously enhancing the thermal and dielectric properties.

The functionalization of polymeric substances is of great interest for the development of innovative materials for advanced applications. For many decades, the functionalization of chitosan has been a convenient way to improve its properties with the aim to prepare new materials with specialized characteristics. In the present article, we summarize the latest methods for the modification and derivatization of chitin and chitosan, trying to introduce specific functional groups under experimental conditions, which allow a control over the macromolecular architecture. This is motivated because an understanding of the interdependence between chemical structure and properties is an important condition for proposing innovative materials. New advances in methods and strategies of functionalization such as click chemistry approach, grafting onto copolymerization, coupling with cyclodextrins and reactions in ionic liquids are discussed.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

Polyamides (PAs) are one of the most important engineering polymers; however, the difficulty in dissolving them hinders their applications. Formic acid (FA) is the most common solvent for PAs, but it has industrial limitations. In this contribution, we proposed a new solvent system for PAs by replacing a portion of the FA with urea and calcium chloride (FAUCa). Urea imparts the hydrogen bonding and calcium ion from the calcium chloride, as a Lewis acid was added to the system to compensate for the pH decrease due to the addition of urea. The results showed that the proposed solvent (FAUCa) could readily dissolve PAs, resulting in less decrease in the mechanical properties during the dissolution. The composite prepared using the FAUCa has almost the same properties like the one prepared using the FA solution. The solution was applied on a polyamide 66 fabric to make an all-polyamide composite coated-fabric, which then was characterized. The FAUCa solution had a higher viscosity than the one prepared using the neat FA solvent, which can be an advantage in the applications which needs higher viscosity like preparing the all-polyamide composite coated-fabric. A more viscouse solution makes a denser coating which will increase the water-/gas-tightness. In conclusion, using the FAUCa solvent has two merits: 1. replacement of 40 % of the FA with less harmful and environmentally-friendly chemicals and 2. enabling for the preparation of more viscouse solutions, which makes denser coating.

In this paper, the influence of the various degradation conditions, on the molecular and supramolecular structure of polybutylene succinate (PBS) and polybutylene succinate adipate (PBSA) copolymer during degradation time is described. Experiment was carried out by the use injection molded samples and normalized conditions of biodegradation in soil, composting and artificial weathering. Materials were studied by using size-exclusion chromatography (SEC) coupled with multiangle laser light scattering (MALLS) detection and wide-angle X-ray diffraction (WAXD). Additionally, the physical and mechanical properties of the samples were determined. The performed experiments clearly show difference impact of selected degradation condition on the macroscopic, supramolecular and molecular parameters of studied aliphatic polyesters. The structural changes in PBS and PBSA explain the observed changes in the physical and mechanical properties of the obtained injection molded samples.

The aim of this work is the preparation of contact active antimicrobial films by blending copolymers with quaternary ammonium salts and polyacrylonitrile as matrix material. A series of copolymers based on acrylonitrile and methacrylic monomers with quaternizable groups were designed with the purpose of investigating the influence of their chemical and structural characteristics on the antimicrobial activity of these surfaces. The biocide activity of these systems was studied against different microorganisms, such as the Gram-positive bacteria Staphylococcus aureus and the Gram-negative bacteria Pseudomona aeruginosa and the yeast Candida parapsilosis. The results confirmed that parameters such as flexibility and polarity of the antimicrobial polymers immobilized on the surfaces strongly affect the efficiency against microorganisms. In contrast to the behavior of copolymers in water solutions, when they are tethered to the surface, the active cationic groups are less accessible and then the mobility of the side chain is critical for a good contact with the microorganism. Blend films composed of copolymers with high positive charge density and chain mobility present up to a more than 99.999% killing efficiency against the studied microorganisms.

Mixtures of methacrylic polymers are the most common materials for making composites to be used as resins for dental and cosmetic applications. Some of these mixtures are composed by poly (ethyl methacrylate) (PEMA) and poly (methyl methacrylate) (PMMA), which constitute a solid component to be mixed with a liquid component made out of methacrylate monomers. The reaction between the thermal initiator benzoyl peroxyde (BPO) present in the solid component and the activator of the polymerization process, N,N-dimethyl-p-toluidine (DMT) present in the liquid component, gives rise to thermoset materials. In the present study, different liquid formulations composed by a mixture of two methacrylic monomers, ethyl methacrylate (EMA) and triethylene glycol dimethacrylate (TEGDMA) for cosmetic applications, were prepared and characterized, using a commercial powder (POW) composed by PEMA and PMMA. With the aim of improving workability during final application of the material, it was necessary to slow down the polymerization rate of liquid formulations. Their thermal behaviour was investigated by DSC in order to check the polymerization rate. Thermal stability of final materials was determined by TGA. DMTA, microindentation hardness and impact tests were performed on final materials, to assess their performance with respect to standard formulation. The combination of thermal and mechanical properties allows choosing which formulations could be suitable for use in cosmetics.

The effect of configuration of an asymmetric bulky initiator 2,2’-[1,1’-binaphtyl-2,2’-diyl- bis-(nitrylomethilidyne)]diphenoxy aluminum isopropoxide (Ini) on structure of copolymer of asymmetric monomer L,L-lactide (Lac) with symmetric comonomer trimethylene carbonate (Tmc) was studied using polarimetry, dilatometry, SEC and ¹³C NMR. When the S-enantiomer of Ini was used the distribution in copolymer chains at the beginning of polymerization is statistical, with alternacy tendency, changing next through a gradient region to homoblocks of Tmc. When, however, R-Ini was used, the product formed was a gradient oligoblock one, with Tmc blocks prevailing at the beginning, changing to Lac blocks dominating at end part of chains. Initiation of copolymerization with the mixture of both initiator enantiomers (S:R = 6:94) gave multiblock copolymer, of similar features but shorter blocks. Analysis of copolymerization progress required complex analysis of dilatometric data, assuming different molar volume contraction coefficients for units located in different triads. Comonomer reactivity ratios of studied copolymerizations were determined.

With huge varieties of fabrics, the first challenge for any performance evaluation is to categorize the vast types of the products into fewer, more homogeneous and thus akin groups. Classification or sorting is arguably the first step of any scientific investigation, and comparison of product quality is meaningful only when conducted within a group of comparable products. A new criterion termed fabric linear density λ is first proposed in this paper so that fabrics can in general be divided into 4 groups. The derivation and validation of this parameter are provided. The importance of fabric drape is almost self-evident, but there is still no effective ways to measure this fabric attribute. The Cusick Drapemeter suffers from its low repeatability and low sensitivity, and is hence not widely or frequently used. The PhabrOmeter, along with the fabric linear density λ, is proposed and demonstrated in this study as a much more efficient alternative for fabric drape test. By actually testing 40 various fabrics, the principle, procedure and results of this method is presented in this paper.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

In this work, the apparent shear strength at the interface between a bamboo fiber and the surrounding poly(lactic acid) (PLA) matrix is quantified. A method for processing pull-out test samples within a controlled embedded length is proposed and the details of the test procedure are presented, along with a critical discussion of the results. Two series of samples are considered: untreated and mercerized bamboo fibers from the same batch, embedded in the same polyester matrix. Electron and optical microscopy are used to observe the fiber-matrix interface before and after the test, and to identify the failure mode of each sample, especially as regards the occurrence of fibrillation in the fiber bundles. The values of apparent interfacial shear strength are calculated only for regular fibers successfully pulled out from the matrix, and reported with their statistical variations. Mercerization, whose efficiency was proven by Fourier Transform InfraRed (FTIR) spectroscopy, did not appear though to improve the quality of the interface (τ_app = 7.0 ± 3.1 MPa for untreated fibers and τ_app = 5.3 ± 2.4 MPa for treated fibers).

The feasible, reliable and selective multi-template molecularly imprinted polymers (MT-MIPs) based on SBA-15 (SBA-15@MT-MIPs) for the selective separation and determination of the trace level of ginsenoside Rb₁ (Rb₁), ginsenoside Rg₁ (Rg₁) and notoginsenoside R₁ (R₁) (Panax notoginseng saponins, PNS) from biological samples were developed. The polymers were constructed by SBA-15 as support, Rb₁, Rg₁, R₁ as multi-template, acrylamide (AM) as functional monomer and ethylene glycol dimethacrylate (EGDMA) as cross-linker. The new synthetic SBA-15@MT-MIPs were satisfactorily applied to solid-phase extraction (SPE) coupled with high performance liquid chromatography (HPLC) for the separation and determination of trace PNS in plasma samples. Under the optimized conditions, the limits of detection (LODs) and quantitation (LOQs) of the proposed method for Rb₁, Rg₁ and R₁ were in the range of 0.63-0.75 ng mL^-1 and 2.1-2.5 ng mL^-1, respectively. The recoveries of R₁, Rb₁ and Rg₁ were obtained between 93.4% and 104.3% with relative standard deviations (RSDs) in the range of 3.3-4.2%. All results show that the obtained SBA-15@MT-MIPs could be a promising prospect for the practical application in the selective separation and enrichment of trace PNS in the biological samples.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

As the interface between human and machine becomes blurred, hydrogel incorporated electronics and devices have emerged to be a new class of flexible/stretchable electronic and ionic devices due to their extraordinary properties, such as soft, mechanically robust and biocompatible. However, heat dissipation in these devices could be a critical issue and remains unexplored. Here, we report the experimental measurements and equilibrium molecular dynamics simulations of thermal conduction in polyacrylamide (PAAm) hydrogels. The thermal conductivity of PAAm hydrogels can be modulated by both the crosslinking density and water content in hydrogels. The crosslinking density dependent thermal conductivity in hydrogels varies from 0.33 to 0.51 Wm^-1K^-1, giving a 54% enhancement. We attribute the crosslinking effect to the competition between the increased conduction pathways and the enhanced phonon scattering effect. Moreover，water content can act as filler in polymers which lead to nearly 40% enhancement in thermal conductivity in PAAm hydrogels with water content vary from 23 to 88 wt%. Furthermore，we find the thermal conductivity of PAAm hydrogel is insensitive to temperature in the range of 25 ^oC – 40 ^oC. Our study offers fundamental understanding of thermal transport in soft materials and provides design guidance for hydrogel-based devices.

All-polyamide composite coated fabric (APCCF) materials were developed and used as the material of construction of textile bioreactors as a replacement of traditional costly steel-/concreate-based bioreactors. Then, APCCF-bioreactor was used to cultivate filamentous fungus Neurospora intermedia to produce ethanol and fungal biomass. The results showed similar performance of the fungus cultivated in stain-less steel bioreactors. Techno-economical analysis for a 5000-m³ APCCF bioreactor for fermentation facility would lead to a reduction of the annual production cost of the facility by $128,000,000 compared to similar stainless-steel processes. The comparative analyses (including mechanical and morphological analyses, density measurements and techno-economical analysis) revealed that the APCCF is a better candidate for material of construction of the textile bioreactor. The APCCF is a 100% recyclable single polymer composite which was prepared from textile production line waste.

Fluorophore molecules can be monitored by fluorescence spectroscopy and microscopy which are highly useful and widely used techniques in cell biology, biochemistry and medicine (e.g., biomarker analysis, immunoassays, cancer diagnosis). Several fluorescent micro- and nanoparticle systems based on block copolymer micelles and cross-linked polymer networks, quantum dots, -conjugated polymers, and dendrimers have been evaluated as optical imaging systems. In this review, we highlight recent advances in the construction of fluorescent single-chain nanoparticles (SCNPs) which are valuable artificial soft nano-objects with tunable, small size (as small as 3 nm). In particular, the main methods currently available to endow SCNPs with fluorescent properties are discussed in detail, showing illustrative examples.

Enzymes are the most efficient catalysts known working in an aqueous environment near room temperature. The folding of individual polymer chains to functional single-chain nanoparticles (SCNPs) offers many opportunities for the development of artificial enzyme-mimic catalysts showing both high catalytic activity and specificity. In this review, we highlight recent results obtained in the use of SCNPs as bioinspired, highly-efficient nanoreactors (3–30 nm) for the synthesis of a variety of nanomaterials (inorganic nanoparticles, quantum dots, carbon nanodots), polymers and chemical compounds, as well as nanocontainers for CO₂ capture and release.

In this paper, a geometric body-centered model to simulate the periodic structure of unidirectional fibrous composites is presented. To this end, three prescribed configurations are introduced to predict in a deterministic manner the arrangement of internal and neighboring fibers inside the matrix. Thus, three different representative volume elements (RVEs) are established. Furthermore, the concept of the interphase has been taken into account, stating that each individual fiber is encircled by a thin layer of variable thermomechanical properties. Next, these three unit cells are transformed in a unified manner to a coaxial multilayer cylinder model. This advanced model includes the influence of fiber contiguity in parallel with the interphase concept on the thermomechanical properties of the overall material. Then, by the use of this model, the authors propose explicit expressions to evaluate the longitudinal and transverse thermal conductivity of this type of composite. The theoretical predictions were compared with experimental results, as well as with theoretical values yielded by some reliable formulae derived from other workers, and a reasonable agreement was found.

Due to the fact that abrasive media can deform flexibly in abrasive flow machining (AFM) making this method easily to polish the complex holes and the curved surface of the hard machining shapes. Although abrasive media dominate the polishing behavior in AFM process, the mechanism of the abrasive media are not easy to understand because of the high viscous gels, therefore, many finishing works need lots of time to design AFM process. Power laws of the abrasive gels is studied here to evaluate the non-Newtonian flow of abrasive gels in complex holes polishing firstly, at the mean time different abrasive gels are utilized to finish the complex holes to follow the results by non-Newtonian flow calculation. Moreover, traditional AFM has difficulty to achieve a uniform roughness of radial distribution in the complex holes polishing because of the non-uniform abrasive forces. So a helical passageway is proposed to create a multiple motion of abrasive medium and to obtain the even surface of the complex holes in AFM process.

The aim of this study was to using a lignin based resin (LB) to improve the performance of the soy flour based adhesive. Soy flour (SF), polyamidoamine-epichlorohydrin (PAE), LB was used to develop a plywood adhesive. The solid content and viscosity of the adhesive, functional groups, thermo-stability, and crystallinity of the cured adhesive were characterized and the performance of the resultant adhesive was evaluated by fabricating three-ply plywood. Results showed using LB and PAE mixture to modify SF adhesive improves dry and wet bond strength by 66.3 and 184.2%. PAE contributed more for the wet bond strength improvement and the LB contributed more for the dry bond strength. The improvement was attributed to: 1) LB/PAE reacted with the functions of the soy protein and form a cross-linking network; 2) Polycondensation reaction between LB molecules further improved crosslinking density of the adhesive and formed a interpenetration structure with crosslinked protein; 3)The easy penetration of LB on wood surface and formed more interlock with wood. The denser structure created by LB and PAE mixture improved the thermal stability and decreased the crystallinity of cured adhesive. The usage of the LB and PAE mixture increased solid content by 35.5%, meanwhile, makes its viscosity acceptable for the industrial application.

The present study investigates the failure mechanisms of industrial fiber materials, using a custom designed fiber cutting performance test bench. The fracture morphologies of single PA6 fibers are examined by scanning electron microscopy. The analysis reveals that fiber cutting can be distinguished according to four distinct stages of fiber failure represented by shearing, cutting, brittle fracture, and tensile failure, which are the result of different mechanisms active during the processes of crack initiation, extension and fracture. The results of fractographic analysis are further verified by an analysis of the blade assembly speed with respect to time over the entire fracture failure process based on high-speed camera data. The results of fractographic analysis and blade assembly speed are fully consistent.

We demonstrated an ITO-free, highly transparent organic solar cell with the potential to be integrated into window panes for energy harvesting purposes. A transparent, conductive ZnO/Ag/ZnO multilayer electrode and a Ag:Ca thin film electrode were used in this transparent device as the bottom and top electrode, respectively. To further improve the transmittance of the solar cell, the thickness of the top ZnO layer was investigated by both experiment and simulation. An average visible transmittance of > 60% was reached, with a maximum transmittance of 73% at 556 nm. Both top and bottom illumination of the solar cell generated comparable power conversion efficiencies, which indicates the wide application of this solar cell structure. In addition, we fabricated distributed Bragg reflector mirrors with sputtered SiO2 and TiO2, which efficiently increased the power conversion efficiency over 20% for the solar cells on glass and PET substrates,

Rigid polyurethane foams were synthesized using a renewable polyol from the simple physical mixture of castor oil and crude glycerol. The effect of the catalyst and blowing agent in the foams properties was evaluated. The use of physical blowing agent (cyclopentane and n-pentane) allowed obtaining foams with smaller cells in comparison with the foams produced with a chemical blowing agent (water). The increase of water content caused a decrease of density, thermal conductivity, compressive strength and Young's modulus, which indicates that the increment of CO₂ production contributes to the formation of larger cells. Higher amount of catalyst in the foam formulations caused a slight density decrease and an increase small significance of thermal conductivity, compressive strength and Young's modulus values. These green foams presented properties that indicate a great potential to be used as thermal insulation, as density (23 - 41 kg m^-3), thermal conductivity (0.0128 – 0.0207 W m^-1 K^-1), compressive strength (45 - 188 kPa) and Young's modulus (3 - 28 kPa). These biofoams are also environmental friendly alternatives and can aggregate revenue to biodiesel industry, contributing for reduction of this fuel prices.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.