In recent years, the production of cement has grown globally in a very rapid manner due to the modernization of the world we live in, and after fossil fuels and land-use change, cement production is the third-largest source of anthropogenic emissions of carbon dioxide, CO₂. Cement being the primary binding material for concrete and with the prospects for the concrete industry continues to grow so will the emissions of CO₂. Hence, a method to reduce the CO₂ production while keeping up with the progression of the concrete industry is very crucial in current times. This is where CO₂ sequestration comes in. It is a process where CO₂ is converted into a mineral which will then be trapped into the concrete forever. Required data to carry out the research between CO₂ sequestered concrete and concrete without CO₂ have been observed, obtained and tabulated as necessary. These data are then used to compare the concrete samples with one another and also prove the theoretical effects of CO₂ exposure to concrete. Hence, experimental results on the compressive strength of the concrete samples for 7, 14 and 28 days has also been tabulated, graphed and further disputed. The objective of this research is mainly to determine the compressive strength of CO₂ sequestered concrete in comparison with concrete without CO₂ in order to decrease the effects the concrete industry has on the environment. The compressive strength of concrete samples with sequestration of CO₂ gas is expected to be higher than of the concrete without CO₂.

This paper presents the results of the experimental research and numerical analysis of three reinforced concrete deep beams with openings, designed by the Strut-and-Tie method according to the EN 1992-1-1 recommendations. All tested specimens were made in full size, with the same geometric characteristics and quality of the materials. The specimens, constructed as simply supported beams, were loaded with two concentrated forces and were tested for bending until failure. Each specimen was reinforced with different reinforcement layout determined by parameter variation within the Strut-and-Tie method. Based on the results of experimental research, it was concluded that the behavior of loaded members was in agreement with the proposed forms of the Strut-and-Tie models that were used for their design.

In the past decades, Fiber Reinforced Concrete has been gaining more attention in the concrete research development. There are many advantages of the inclusion of fiber into reinforced concrete structures. It was found that the inclusion of fibers in concrete, be it synthetic or natural, resulted in the improvement of the thermal properties of concrete, as well as its strength to some extent. However, the inclusion of fibers in concrete does affects its thermo-mechanical properties. The objective of this study is to identify the potential of the addition Polypropylene and Kenaf fibers in cement mortar at different compositions (0.1%, 0.2%, and 0.3%). Eight mixes were analyzed for this purpose. Upon investigating the flow ability, compressive strength, tensile strength, and thermal conductivity of the mortar samples, it was found that the incorporation of PP and Kenaf fibers reduced the flow ability. Cement mortar samples containing 0.1% addition of PP and Kenaf fibers show the highest compressive strength compared to other percentages, while samples containing 0.3% addition of PP and Kenaf fibers show the highest tensile strength compared to other percentages. The thermal conductivity of mortar samples shows reduction when high percentages of both fibers were used.

The effects of the surface waves generated by the wind have a significant effect on the currents. A wave current coupled model plays an important role in the design of offshore structures. The interaction between fluids such as incompressible ocean waves and current and offshore structures is significant with many real-time applications in offshore engineering. These coupled models can be applied to Offshore Floating Production Operating and offloading (FPSO), Wind or current turbines and offshore pipelines. The complex issues related to the design are analyzed by using Computational Fluid Dynamics, which requires an investigation of the multiphase flow between wave and current and the structure which is considered restrictive due to the computational cost. If viscous effects are neglected then the single-phase flow models have been recommended, where wave-current interaction have been modelled successfully. Models have been developed where velocities and pressure are computed and the results can be verified with the experimental results available in the literature. In this study the existing numerical methods, mesh types are discussed along with their coupling methods. Here single-phase and multiphase models with small and medium movement are reviewed and their applications are highlighted.

Keenjhar Lake is the main source of drinking water for the metropolitan city of Karachi. The release of untreated wastewater from Kotri industrial area and other sources have made the lake water polluted. This study was subjected to determine the impacts of such pollutant sources on the water quality of Keenjhar Lake. The study involves the analysis of water quality parameters of Keenjhar Lake and its Feeding source (KB Feeder). The sampling sites were selected based on the sources of contamination. The water samples are tested for physical, chemical and microbiological parameters. The result of water analysis indicates the contamination level of the lake is quite alarming for the sites of Kotri effluent and WAPDA colony where Total Dissolved Solids (TDS), Chloride and other ionic metals were quite higher in concentration than other sites. These sites are also contaminated with Fluoride and Arsenic which are carcinogenic elements. The study reveals that the contamination level of feeding source is causing big non-reversible damage to the lake if continued to be uncontrolled. This contamination is mainly due to the release of toxic metals and ions in the KB feeder caused by human carelessness.

To enable purposeful design and implementation of automated concrete technologies, precise assessment and prediction of the complex material flow at various stages of the process chain are necessary. This paper investigates the intermediate stage of the extrusion and deposition processes in extrusion-based 3D-concrete-printing, using a numerical model based on the Particle Finite Element Method (PFEM). In PFEM, due to the Lagrangian description of motion, remeshing algorithms and the alpha shape method are used to track the free surface during large deformation scenarios. The Bingham constitutive model was used for describing the rheological behaviour of fresh concrete. This model is validated by comparing the numerically predicted layer geometries with those obtained from laboratory 3D printing experiments. Extensive parametric studies were then conducted using the numerical simulation, delineating the influence of process and material parameters on the layer geometries, the dynamic surface forces generated under the extrusion nozzle and the inter-layer interactions.

Frequent flooding from sea-level rise (SLR) is one of the immediate climate change impacts affecting low-lying and exposed coastal communities. These communities rely upon the delivery of three-waters services for wastewater, stormwater and water supply. Due to ongoing SLR, managing these networks will increasingly be a challenge. This raises the issue of how local government can reconcile maintaining levels of service as the impacts of climate change and their uncertainties worsen over the coming decades (and beyond). Can they be adapted over time to retain levels of service or will they eventually require retreat and if so at what adaptation threshold? This paper explores managed retreat of two-waters infrastructure (wastewater and stormwater) as an adaptation option using a Dynamic Adaptive Pathway Planning (DAPP) approach. In the study, we use DAPP to frame the retreat of two-water networks, developing a combination of an area specific retreat strategy, pathway portfolios, retreat phases, land use change signaling and identify pathway conflicts and synergies. Repurposing retreated areas by utilizing Water Sensitive Urban Design (WSUD) options was found to extend retreat thresholds for adjacent areas. A systematic ’routine’ developed in this study provides a structured approach for managed retreat of two-water infrastructure with the aim to reduce future disruption from flooding, signal land use changes early and allow for gradual budget adjustments by the agencies to manage expenditure over time. This approach helps inform and improve the decision-making process for the agencies and the communities they serve, by providing a stepwise process that can be communicated spatially and visually, thereby making a retreat adaptation option more manageable.

The identification of homogeneous flood regions is essential for regional flood frequency analysis. Despite the type of regionalization framework considered (e.g., region of influence or hierarchical clustering), selecting flood-related attributes to reflect flood generating mechanisms is required to discriminate flood regimes among catchments. To understand how different attributes perform across Canada for identifying homogeneous regions, this study examines five distinctive attributes (i.e., geographical proximity, flood seasonality, physiographic variables, monthly precipitation pattern, and monthly temperature pattern) for their ability to identify homogeneous regions at 186 gauging sites. We add an automatic component to enhance identification of homogeneous regions is proposed as an addition to the region of influence framework. Results are presented spatially for Canada to assess patterning of homogeneous regions. Memberships of two selected regions are investigated to provide insight into membership characteristics. Sites in eastern Canada are highly likely to identify homogeneous flood regions, while the western prairie and mountainous regions are not. Overall, it is revealed that the success of identifying homogeneous region is relevant to local hydrological complexities, to whether considered attribute reflects primary flooding mechanism, and to whether catchment sites are clustered in small geographic region. Formation of effective pooling groups affords the extension of record lengths across the Canadian domain (where gauges typically have <50 years of record), facilitating more comprehensive analysis of higher return periods floods need for climate change assessment.

The reuse of recycled crushed concrete aggregate (RCCA) and reclaimed asphalt pavement (RAP) can provide a sustainable solution for the disposal of C&amp;D materials instead of sending it to landfill. More importantly, it will save energy and reduce impact on the environment. Several states in USA are using RCCA and RAP as base materials for years, focusing on the quality of the recycled materials. The structure of Recycled Aggregate (RA) is more complex than Natural Aggregate (NA). RAs have old mortar adhered on them that forms a porous surface at interfacial transition Zone (ITZ) and prevents new cement mix from bonding strongly with the aggregates. The objective of this work was to correlate microstructural properties like micro-porosity, inter and intra aggregate pores with the unconfined compressive strength (UCS) of RAP and RCCA molds, mixed at different proportions. In this paper, the quantity of micro-pores and their effect on the strength of mixed materials is used as the basis of microstructural analysis of recycled concrete and reclaimed asphalt. Microstructural properties obtained from the analysis of scanning electron microscope (SEM) images were correlated with unconfined compressive strength. Intra-aggregate and inter-aggregate pores were studied for different ratios of cement treated mixture of RAP and RCCA. The results show that the number of pores in the mixture increases considerably by adding RAP, which eventually causes reduction in unconfined compressive strength. In addition, significant morphological and textural changes of recycled aggregates were observed by SEM image analysis.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

Aerated concrete, which is manufactured from binding material, sand, foaming agent and water, is currently being utilized in the construction industry because of its lightweight and durability. The binding material, cement, along with other materials used in the concrete produces huge carbon footprints during its fabrication. The utilization of natural aggregates name as coarse aggregates depletes the natural resources of the country. Therefore, huge amounts of agricultural wastes have led scholars to investigate the effectiveness of replacing conventional materials used in concrete with agricultural wastes. In the current study, rice husk ash (RHA) was used as supplementary cementing material, thereby reducing the amount of cement used in aerated concrete (AC) mixture will reduce carbon footprints. The experimental and numerical analysis were conducted to investigate structural behavior of reinforced RAC- B beams subjected to flexural load. Parametric study on structural performance of RAC- B beam under flexure were conducted using finite element analysis (FEA). From the experiment and FEA. Results from the parametric study showed that RAC-10%RHA-B with higher depth structurally performed better compared to RAC-B under flexure with greater load carrying capacity, lesser maximum deflection, and less cracks developing in the tension area.

Recently, the intensities of natural disasters have increased significantly owing to climate change and various other environmental factors, causing unprecedented damage. Measures must be established to reduce damage from large-scale natural disasters caused by the rapidly changing environment. The Japanese government published a hazard map manual in 2015 and obligates the creation of a hazard map as a measure to reduce high-scale storm surges. This manual presents a typhoon model based on a parametric model that is used to create a hazard map. The Myers model assuming concentric circles, which is primarily used in East Asia, is disadvantageous as it cannot consider geographic characteristics. Therefore, a new parametric model is necessary to calculate wind and pressure fields, which change according to geographic characteristics. To improve this limitation of the Myers model, we calculated the wind and pressure fields considering geographical effects by combining the Holland model, which can consider the size of a developing typhoon, and the Mascon model, which changes by geographic characteristics. To determine the gradient coefficient of the Holland model, the coefficient that changes every moment was calculated using grid point value data. The result indicated excellent reproducibility of storm surge height according to the geographic characteristics.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

Taking into account the increase in the emission of greenhouse gases produced by ships, during navigation and maneuvering in the port, a direct consequence of the increase in maritime traffic, the international community has developed a broad set of regulations to limit such emissions. The installation in commercial ports of automatic mooring systems by means of vacuum suction cups (AMS), thus reducing considerably the time required to carry out the mooring and unmooring maneuvers of ships, is a factor that is considerably influencing the decrease in Emissions of polluting gases in commercial ports with high traffic. The objective of the present work is to verify the influence of the use of the AMS on the emissions of polluting gases produced in the facilities destined to the traffic of container ships. It examines the CO2 emissions of container ships that call in the only three container ports equipped with AMS: Salalah (Oman), Beirut (Lebanon) and Ngqura (South Africa). Between them, these three ports supported the transit of 6 million TEUS in 2017. The calculation of emissions is made taking into account the time saved when performing the mooring maneuvers using the new AMS system compared with when it is not used. To do this, two different calculation methods are used: EPA and ENTEC to then compare the results of the two and thus obtain the reduction in emissions per TEU in these terminals during the mooring maneuvers. The paper concludes with a discussion on the values of the reductions in emissions obtained and the advantages of the installation of AMS in commercial ports located near population centres.

Bayesian model calibration techniques are commonly employed in the characterization of nonlinear dynamic systems, as they provide a conceptual and effective framework to deal with model uncertainties, experimental errors and procedure assumptions. This understanding has resulted in the need to introduce a model discrepancy term to account for the differences between model-based predictions and real observations. Indeed, the goal of this work is to enhance model-driven Structural Health Monitoring procedures by incorporating the posterior uncertainty linked to updated model discrepancy, and thus make relevant considerations for its use in the Structural Health Monitoring. Specifically, the Bayesian inference has been applied to the calibration of nonlinear hysteretic systems to both provide: (i) most probable values (MPV) of the parameters following the calibration, and; (ii) estimates of the model discrepancy posterior distribution. The effect of the model discrepancy in the calibration is first illustrated recurring to a single degree of freedom Bouc-Wen type oscillator, and then applied for calibrating a reference nonlinear Bouc-Wen model, deriving from real data acquired on a monitored masonry building.

Design criteria for coastal defenses exposed to wave overtopping are usually assessed by mean overtopping discharges and maximum individual overtopping volumes. However, it is often difficult to give clear and precise limits of tolerable overtopping for all kind of layouts. A few studies analyzed the relationship between wave overtopping flows and hazard levels for people on sea dikes, confirming that one single value of admissible mean discharge or individual overtopping volume is not a sufficient indicator of the hazard, but detailed characterization of flow velocities and depths is required. This work presents the results of an experimental campaign aiming at characterizing the flow characteristics associated to maximum individual overtopping volumes for an urbanized stretch of a town along the Catalan coast, where a walking and bike path and a railway run along the coastline are exposed to significant overtopping events every stormy season. The work compares different safety criteria for pedestrian. Results prove that safety of pedestrian on a sea dike can be still guaranteed even for overtopping volumes larger than 1000 l/m. Pedestrian hazard is rather proved to be linked to the combination of overtopping flow velocity and flow depth.

The complexity of the design in high-rise residential projects is a challenge for the construction industry in completing projects that fit the needs of users. Performance-Based Building Design (PBBD) appears as a design concept that can describe these needs into performance requirements. In this case designing a building can be considered as an iterative process of exploration, where desired functional properties can be created, the shapes are suggested, and evaluation processes is used, so as to bring together the shapes and functions of the building. This concept is a container for designers to produce high-performance buildings. This study aimed to identify the performance-based building design factors applied by architect designers and engineers in high-rise residential building in Surabaya. As part of this study, primary data was collected based on surveys conducted through observation and questionnaire distributed to designers who had or were involved in the high-rise residential design process in Surabaya. A total of sixty-eight respondents were included in this study. Descriptive analysis through a mean and standard deviation scatter plot was used to rank the application of PBBD. Meanwhile, factor analysis was used in the analysis of PBBD application factors. From the results of the analysis, four factors were obtained for the application of PBBD in high-rise residential buildings in Surabaya, namely; the interests of occupants, the sustainability of building operations, the design collaboration process, and the risk of loss. Future research is the influence relationships and measure the success model of PBBD at a higher level into BIM (Building Information Modeling) interoperability.

With the continuous emergence and application of new technologies, the construction of smart cities has entered the practical promotion period. Since 2012, the pilot construction of smart city has been promoted by the government in China. On the basis of these practical experiences, this paper presents an overview of the latest technologies and applications for smart city construction in China and demonstrates that smart city strategy needs to be implemented according to local conditions, adhering to the people-oriented concept and using scientific and effective top-level design and planning. The construction of smart city is comprehensive system engineering, including the integration of geographic information sharing service platform, full-cycle management and control system of urban planning, construction and social management, as well as intelligent business information management system of gardening, water conservancy, environmental protection and other industries and departments. The information system (GIS), satellite remote sensing (SRS), global navigation satellite system (GNSS), Internet of things, mobile applications, cloud computing, visualization technology ware used to promote urban construction and sustainable development, and to meet the needs of future smart city development. Results show that centralized management is very important for the construction of smart city. The government plays a major role in the construction of smart city, which will be conducive to the development of new technologies and the effective use of smart city construction resources.

River sediment from two inflow watersheds (Hongze and Tiaoxi) to Hongze and Taihu Lake in Eastern China was analyzed by the sequential extraction procedure. This study aimed to explore a spatial distribution of phosphorus fractions in river sediments and analysed the relationship between different phosphorus fractions and their environmental influence on the sediments within different watersheds in Eastern China. Five fractions of sedimentary phosphorus, including freely sorbed phosphorus, were all analyzed (NH₄Cl-P), redox-sensitive phosphorus (BD-P), bound phosphorus metal oxide (NaOH-P), bound phosphorus calcium (HCl-P) and residual phosphorus (Res-P). The order of rank of the P fractions for the river Anhe was HCl-P>NaOH-P>BD-P>NH₄Cl-P; whereas that of the Suihe river was HCl-P>BD-P>NaOH-P>NH₄Cl-P. For the rank order of the Hongze watershed, HCl-P was higher while the NH₄Cl-P contents were significantly lower. The rank order for the Dongtiaoxi river was NaOH-P > HCl-P> BD-P> NH₄Cl-P and that of Xitiaoxi river was NaOH-P> BD-P> HCl-P> NH₄Cl-P. Compared with phosphorus forms of Tiaoxi watershed, NaOH-P contents were significantly higher in the converse of HCl-P contents were significantly higher in Hongze watershed while both in NH₄Cl-P contents were significantly lower. Variations may be attributed to differential discharge of P watershed form due to land-use changes and urban river ambient conditions.

This work proposes a novel methodology for the complete characterization of fiber reinforced concrete (FRC). The method includes bending tests of prismatic notched specimens, based on the Standards for FRC, tensile and pure shear tests. The values adopted by the standards for designing FRC are the obtained from bending tests, typically fR3, even for shear and pure tension loading. This paper shows that the remaining strength of FRC, supplied by the fibers, depends on the type of loading. In the case of shear and tensile loading the prescriptions of the standards may be unsafe. In this work, the remaining halves of specimens subjected to bending test are prepared and used for shear and tension tests. This means significant savings in specimen preparation and a greater amount of information for structural use of FRC. The results provide relevant information for the design of structural elements of FRC compared with the only use of data supplied by bending tests. In addition, a video-extensometry system was used to analyze the crack generation and cracking patterns. The video-extensometry applied to shear tests allowed the assessment of the sliding values and crack opening values at the crack discontinuity. These values may be quite relevant for the study of the FRC behavior when subjected to shear according to the shear-friction model theories.

To quantify damage to reinforced concrete (RC) column members after an earthquake, an engineer needs to know the maximum applied force that was generated by the earthquake. Therefore, in this work, piezoceramic transducers are used to detect the applied force on an RC column member under dynamic loading. To investigate the use of post-embedded piezoceramic sensors in detecting the force that is applied to RC columns, eight full-size RC column specimens with various failure modes are tested under specific earthquake loadings. Post-embedded piezoceramic sensors are installed at a range of depths (70-80 mm) beneath the surface of a column specimen to examine the relationship between the signals that are obtained from them and the force applied by the dynamic actuator. The signals that are generated by the post-embedded piezoceramic sensors, which correlate with the applied force, are presented. These results indicate that the post-embedded piezoceramic sensors have great potential as tools for measuring the maximum applied force on an RC column in an earthquake. Restated, signals that are obtained from post-embedded piezoceramic sensors on an RC column in an earthquake can be used to determine the applied force and corresponding damage or residual seismic capacity.

Hydraulic fracturing has been studied by using dimensional analysis. The universal scaling law of the problem has been formulated. From this investigation, it has found that the key control variable in the process is total damage number $J=\frac{p+\frac{1}{2}\rho U^2}{\sigma_Y}$. The crack length is satisfied with the geometric similarity law if no response time is concerned, otherwise, it would not satisfy the similarity.

The most common index for representing structural condition of the pavement is the structural number. The current procedure for determining structural numbers involves utilizing falling weight deflectometer and ground-penetrating radar tests, recording pavement surface deflections, and analyzing recorded deflections by back-calculation manners. This procedure has two drawbacks: 1. falling weight deflectometer and ground-penetrating radar are expensive tests, 2. back-calculation ways has some inherent shortcomings compared to exact methods as they adopt a trial and error approach. In this study, three machine learning methods entitled Gaussian process regression, m5p model tree, and random forest used for the prediction of structural numbers in flexible pavements. Dataset of this paper is related to 759 flexible pavement sections at Semnan and Khuzestan provinces in Iran and includes “structural number” as output and “surface deflections and surface temperature” as inputs. The accuracy of results was examined based on three criteria of R, MAE, and RMSE. Among the methods employed in this paper, random forest is the most accurate as it yields the best values for above criteria (R=0.841, MAE=0.592, and RMSE=0.760). The proposed method does not require to use ground penetrating radar test, which in turn reduce costs and work difficulty. Using machine learning methods instead of back-calculation improves the calculation process quality and accuracy.

The masonry building Heritage is appreciated for its aesthetic and historical value all around the world. The widespread presence of curved elements, such as arch, vault and dome express the relevant constructive abilities in the different historical epochs. These curved elements are characterized by architectural beauty, structural strength (especially against the gravity loads), thermal comfort and fire resistance. On the other hand, curved structures required scaffolding in order to be erected. The design, the construction and the dismantling of the scaffolds is typically time-consuming and expensive. In addition, the on-site working risk is related to time-interferences (e.g. in manpower working, at the same time, over and under scaffold). This technology dates back to the Era of the Roman Empire and it is currently still used, despite its limitations and disadvantages. In the present paper, an innovative technique (recently patented), aiming for the construction of a curved structural member without scaffolds, is proposed and illustrated. It consists in a Hinged Lifting Arch (HLA), using FRP (Fiber Reinforced Polymer) bonded strips. In details, a series of blocks are cut following an arch geometry and then aligned on the ground-floor in order to bond a composite on their top surface. Moreover, the impregnation of the polymeric adhesive is not allowed at the extremities of each block. The fiber sheet is applied continuously along the entire extrados. In this sense, hinges are introduced, in fact, the FRP-connected blocks are able to easily rotate, in the opposite direction, around the contact ends (i.e. hinge). Finally, the middle block is lifted-up and the arch takes the desiderated shape. In the first experimental demonstration, the natural calcareous stone was used, even if the proposed technique is totally material-independent. Moreover, an analytical model is proposed and discussed for designing the proper aspect ratio of the blocks in order to ensure the full mutual contact when the HLA is totally lifted up. The advantages of the proposed technique are related to the absence of scaffolds and improved seismic strength against horizontal loads thanks to the presence of the FRP, which limits the occurrence of hinges at the extrados.

This work describes a new transducer prototype for continuous monitoring both in the structural and geotechnical fields. The transducer is synthetically constituted by a wire of optical fiber embedded between two fiber tapes (fiberglass or carbon fiber) and glued by a matrix of polyester resin. The fiber optical wire ends have been connected to a control unit whose detection system is based on Brillouin optical time-domain frequency analysis. Three laboratory tests were carried out to evaluate the sensor's reliability and accuracy. In each experiment, the transducer was applied to a sample of inclinometer casing sets in different configurations and with different constraint conditions. The experimental data collected were compared with theoretical models and with data obtained from the use of different measuring instruments to perform validation and calibration of the transducer at the same time. Several diagrams allow comparing the transducer and highlighting its suitability for monitoring and maintenance of structures. The characteristic of the transducer suggests its use as a mixed system for reinforcing and monitoring, especially in lifetime maintenance of critical infrastructures such as transportation and service networks, and historical heritage.

In this paper, optimum parameters of Tuned Mass Dampers (TMD) are considered to control the responses of 10-story shear building under harmonic loading and 22 set of seismic records of FEMA-P695. The criterion used to obtain the optimum parameters is to select mass ratio, the frequency (tuning) and damping ratio that would result in smallest lateral displacements. State-space equations of motion are presented to compute the structural responses by developing a MATLAB file. A 10-story shear building is presented as a case study to assess the effects of TMDs on the multi-story structures. The results indicate that using TMD can reduce structural responses up to the average 20% under earthquake excitation and up to 90% under harmonic loadings. TMDs are not always effective under any type of ground motion; therefore, being aware of the given location is significant to design TMDs properly.

The paper presents the influence of different curing conditions – wet, dry and protection against water evaporation on selected properties of concretes with different amount of recycled concrete aggregate previously subjected to atmospheric CO2 sequestration. Additionally, the eco-efficiency bi and ci indexes as well as eco-durability S-CO2 index were calculated. It was found that dry conditions deteriorate the properties of concrete, especially made of blast furnace slag cement, while protection against evaporation allows to achieve results comparable to wet conditions. Moreover, for series with the highest amount of coarse recycled aggregate and after longer period of curing, the difference between the effects of wet curing and protection against water evaporation disappears. The eco-efficiency and eco-durability indexes approach confirms the beneficial effect of blast-furnace slag cement used as a binder but on condition of proper way of curing.

The corrosion of prestressing steel in prestressed concrete bridges is a critical issue for bridge maintenance. To assess structures with corroded strands, it is necessary to define the mechanical properties of the strands and their influence on the structural behavior. In this study, corroded strands are taken from external tendons in existing bridges and tested to define the effects of corrosion on the tensile properties of the strand. Empirical equations for the tensile strength and ductility of the corroded strand are proposed using test results. The most corroded wire governs the mechanical properties of the strand. Experiments on prestressed concrete beams with a single corroded strand are conducted to investigate the structural behavior. A reduction in the flexural strength and maximum deformation is observed from the experiment. According to the section loss of a wire in a strand and its location in a beam, the flexural capacity can be evaluated using the proposed equation. The reduced ultimate strain of the corroded strand can be the governing factor of the flexural strength.

Mineral wool made from basalt fibers is frequently used as an insulating material in construction systems. In this study, both unused mineral wool, and wool obtained from the softened roofing area, were comprehensively analyzed in a laboratory using different characterization techniques. Firstly, the amount of initial water content and compressive strength at 10% deformation were determined. Secondly, microstructure and surface chemical composition were analysed by Scanning electron microscopy (SEM) equipped with energy dispersive x-ray spectroscopy (EDX). To study heterogeneities near the fiber surface and to examine cross-sectional composition, a Scanning transmission electron microscope (STEM) was used. Finally, to verify possible reasons for resin degradation, Thermogravimetry analysis and differential scanning colometry (TGA-DSC) were simultaneously carried out. The results show that natural aging under high humidity and thermal fluctuations greatly affects the surface morphology and chemical composition of fibrous composite. Phenol-formaldehyde and other hydrophobic compounds that protect fibers against moisture and give compressive resistance were found to be degraded.

This work mainly aims to identify and understand the factors influencing the switching of transportation modes among higher-education students in Joinville, Brazil when traveling to universities. Furthermore, this study evaluates the possibility of switching from individual vehicles to other modes of transport (i.e., bus, bicycle, and walking) by employing a multinomial logit model. The results indicate that students would be interested in switching from individual motor vehicles to other options. The scenarios for switching to buses presented the highest switching probability. The bus cost was the most important factor for switching. Meanwhile, the parking space reduction does not affect the student's choice, indicating that restricting available spaces should not be an isolated measure for decreasing the car mode attractiveness. Finally, the transport mode switch would occur only if alternative modes to the car or their infrastructure are improved; otherwise, students maintain their usual choices.

This study investigated the effects of freeze-thaw cycles on the mechanical properties of hardened self-compacting concrete for varying column heights. A column (100×20×300 cm) was fabricated by C30 self-compacting concrete in the laboratory and 10 cube samples (10x10x10 cm) were taken from fresh concrete as the references. After a period of 28 days, 160 core specimens (Ø67 mm in diameter) were taken from different column heights. Unit weight, water absorption, compressive strength, and freeze-thaw tests were performed on these 170 (10 reference cubic and 160 core) samples. The mechanical properties of the core specimens before freeze-thaw and after 8-56 freeze-thaw cycles were reported for varying column heights. The average compressive strength value of the reference cubic samples was determined as 40.28 MPa, while the compressive strengths of the core specimens before freeze-thaw were ranged from 40.25 MPa to 49.62 MPa, impying an increase in compressive strength values up to 23.18% compared to the reference cubic samples. Compressive strengths of the specimens subjected to 8 and 56 freeze-thaw cycles varied between 38.71‒48.07 MPa and 31.72‒39.11 MPa, respectively. Statistical analysis revealed that the compressive strength of the concrete exposed to 56 freeze-thaw cycles was significantly different from that of the other specimens.

This study investigated the effects of freeze-thaw cycles on the mechanical properties of hardened self-compacting concrete for varying column heights. A column (100×20×300 cm) was fabricated by C30 self-compacting concrete in the laboratory and 10 cube samples (10x10x10 cm) were taken from fresh concrete as the references. After a period of 28 days, 160 core specimens (Ø67 mm in diameter) were taken from different column heights. Unit weight, water absorption, compressive strength, and freeze-thaw tests were performed on these 170 (10 reference cubic and 160 core) samples. The mechanical properties of the core specimens before freeze-thaw and after 8-56 freeze-thaw cycles were reported for varying column heights. The average compressive strength value of the reference cubic samples was determined as 40.28 MPa, while the compressive strengths of the core specimens before freeze-thaw were ranged from 40.25 MPa to 49.62 MPa, impying an increase in compressive strength values up to 23.18% compared to the reference cubic samples. Compressive strengths of the specimens subjected to 8 and 56 freeze-thaw cycles varied between 38.71‒48.07 MPa and 31.72‒39.11 MPa, respectively. Statistical analysis revealed that the compressive strength of the concrete exposed to 56 freeze-thaw cycles was significantly different from that of the other specimens.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

In this paper, the results of finite element analyses of a single-layer cylindrical latticed shell under severe earthquake is presented. A 3D Finite Element model using fiber beam elements were used to investigate the collapse mechanism of this type of shell. The failure criteria of structural members are simulated based on the theory of damage accumulation. Severe earthquake of peak ground acceleration (PGA) of 500 gal was applied to the shell. The stress and defeomation of the shell were studied in detail. A three-stages collapse mechanism “double-diagonal -members-failure-belt” of this type of structure was discovered. Based on the analysis results, the measures to mitigate collapse of this type of structure is recomanded.

Solid particles immersed in a fluid can be found in many engineering, environmental or medical fields. Applications are suspensions, sedimentation processes or procedural processes in the production of medication, food or construction materials. While homogenized behavior of these applications is well understood, contributions in the field of pore-scale fully resolved numerical simulations with non-spherical particles are rare. Using Smoothed Particle Hydrodynamics (SPH) as a simulation framework, we therefore present a modelling approach for Direct Numerical Simulations (DNS) of single-phase fluid containing non-spherically formed solid aggregates. Notable and discussed model specifications are the surface-coupled fluid-solid interaction forces as well as the contact forces between solid aggregates. The focus of this contribution is the numerical modelling approach and its implementation in SPH. Since SPH presents a fully resolved approach, the construction of arbitrary shaped particles is conveniently realizable. After validating our model for single non-spherical particles, we therefore investigate the motion of solid bodies in a Newtonian fluid and their interaction with the surrounding fluid by analyzing velocity fields of shear flow with respect to hydromechanical and contact forces. Results show a dependency of the motion and interaction of solid particles on their form and orientation. While spherical particles move to the centerline region, ellipsoidal particles move and rotate due to vortexes formation in the fluid flow in between.

Silty clay modified by fly ash and crumb rubber is a kind of sustainable subgrade filler which has good anti-freeze-thaw resistance stability but wake vibration isolation performance. The objective of this study was to improve the vibration isolation of the modified soil and investigate the vibration isolation effect of the composite subgrade structure of XPS plates and the modified soil by indoor impact test. First, the vibration isolation performance of silty clay, modified soil and composite subgrade structure was respectively evaluated. Second, the effect of XPS plate’s thickness and vibration intensity on the vibration performance of the composite subgrade structure were evaluated. Third, the vibration isolation performance of the test groups under the condition of freeze-thaw cycles was assessed. The results show that the vibration isolation performance of subgrade can be effectively improved by setting XPS plates. The composite subgrade structure has certain vibration isolation effect, especially in vertical direction. Considering vibration isolation performance and costs, 5cm is the optimum XPS plates thickness. The composite subgrade structure has great vibration isolation performance under the condition of freeze-thaw cycles, so it is suitable to be applied in road subgrade in seasonal frozen regions.

A rehabilitation technique for asphalt pavements with geosynthetic is the application of impregnated nonwoven geotextiles between deteriorated and new asphalt overlays. The performance investigation of impregnated geotextiles proves that they are enhancing in mechanical and hydraulic properties. Although, the installation process may cause severe impacts on these materials’ performance. During the installation, the geotextile suffers damage due to the traffic of high load vehicles, as compactors and pavers, and the friction with granular materials found under its layer or poured above it. This paper aims to investigate how the damage caused by granular materials on nonwoven geotextiles impregnated with different asphalt emulsions effect on their strength resistance and permittivity. From two types of nonwoven geotextiles: polypropylene and polyethylene terephthalate, the comparison uses geotextiles in three conditions: not impregnated, impregnated with asphalt emulsion of rapid setting, and impregnated with asphalt emulsion changed by an elastomeric polymer. Part of the samples followed the damage according to ISO 10722 procedure, placed between three different scenarios of granular materials, applying gravel, sand, and clay. After the damage process, the samples were submitted to mechanical and hydraulic properties evaluations.

Construction and demolition waste (CDW) represents 1/3 of the weight of all-waste produced. Increasing their recycling and reutilization with recycled aggregates (RA) means closing the life cycle of construction materials. Research has been carried out on artificial aggregates from the exclusive crushing of structural concrete waste in selective demolitions (CDWRConc). This study analyses the use of recycled concrete as graded aggregate (GARConc) and in cement soil (CSRConc). The material complies with the requirements as a road base, although due to the low values of resistance to fragmentation these materials are adequate for use in sensitive road systems and other places such as urban roads and car parks. The sensitive road systems are infrastructures in places of great natural wealth and low traffic intensity, with an annual average of heavy vehicle traffic (AADTh) below 50 vhp/d. As soluble salt contents have been detected, additional waterproofing or drainage measures must be adopted to prevent water infiltration into the layers made up of CDWRHorm. Finally, the high initial values of UCS allow the temporary passage of light vehicles over CSRConc after 3 days.

This paper aims to provoke fundamental thinking and action around the value and importance of socially-equitable development to the economic advancement, resilience, and prosperity of communities, as we contend with the 21^st Century grand challenge of the changing climate and disasters. As local communities and the global community have experienced an increased frequency, intensity and duration of natural and man-made disasters over the past several decades, opportunities have also grown to identify and reap the benefits of socially-equitable economic development. Reflecting on the COVID-19 pandemic, we discuss the critical importance of socially-equitable economic development to the resilience and sustainability of communities and the infrastructure that supports them. To this end, we: (1) examine what constitutes socially-equitable economic development at different spatial scales of community; (2) explore whether socially-equitable development can occur at different scales of community; (3) explicate the importance of formally considering the inputs, processes, outputs and outcomes for socially-equitable development; (4) explain why the pursuit of equal distribution of the benefits and burdens of development is a necessary but not sufficient endeavor for socially-equitable economic development; (5) analyze the relationships between socially-equitable development, and resilient and sustainable infrastructure and communities; (6) explain why socially-equitable development should be a key component of infrastructure and community resilience strategies in the 21^st Century; and, (7) explain why socially-equitable development can ultimately be viewed as a long-term strategy for prosperity.

The Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost deviations using proprietary T/S and T/C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

For traffic management under sudden disaster in high-density areas, the first and foremost step is to prevent traffic congestion in the disaster-affected area by traffic flow control, as to provide enough and flexible traffic capacity for emergency evacuation and emergency rescue. Catastrophe border identification is the foundation and the key to traffic congestion prediction under sudden disaster. This paper uses a mathematical model to study the regional traffic flow in the high-density area under sudden fire disaster based on the Cusp Catastrophe Theory (CCT). The catastrophe border is identified by fitting the CCT-based regional traffic flow model to explore the stable traffic flow changing to the instable state, as to provide a theoretical basis for traffic flow manage and control in disaster-affected areas, and to prevent the traffic flow being caught into disorder and congestion. Based on VISSIM simulator data by building simulation scenarios with and without sudden fire disaster in a Sudoku traffic network, the catastrophe border is identified as 439pcu/lane/h, 529pcu/lane/h, 377pcu/lane/h at 5s, 10s, 15s data collection interval respectively. The corresponding relative precision, which compares to the method of Capacity Assessment Approach (CAA), is 89.1%, 92.7% and 76.5% respectively. It means that 10s data collection interval would be the suitable data collection interval in catastrophe border identification and regional traffic flow control in high-density area under sudden fire disaster.

There exists a great potential for application in soil mechanics with the use of mechanistic models such as the finite element model, and other non-local models, such as the peridynamic model, since the soil mass can be modelled as a group of particles that interact with each other. In this work, we determine the bearing capacity of deep foundations where stresses are transmitted to deep deposits, which generally present better characteristics in terms of compressibility and shear strength. One of the main elements are driven piles, which must be previously designed, made and tested before their final use. In this work, a comparison with different methods is presented. The finite element method and the peridynamic model are used. Because the effect of consolidation was not taken into account, in these examples, the assumption is made that the structures are cemented in inert soil. Likewise, it is assumed that the water table has no influence on the simulations. Failure envelopes were observed where bonds between particles present high gradients of deformation and fracture. Bearing capacities were estimated and compared with those obtained from the Terzaghi and Meyerhof methods.

Predictive simulation of concurrent debris flow using only pre-disaster information has proven to be difficult as a result of problems in predicting the location of debris-flow initiation (i.e., slope failure). However, because catchment topography has concave characteristics, with all channels in a catchment joining each other as they flow downstream, it is possible to predict damage to downstream area using relatively inaccurate initiation points. Based on this, this paper presents methodologies employing debris-flow initiation points generated randomly using statistical slope failure prediction. A many-case simulation across numerous initiation points was performed to quantify the effect of slope-failure location in terms of deviations in the predicted water level and terrain deformation. It was found that the relative standard deviation diminished as the points approached the downstream area, indicating a location-based predictability effect.

The purpose of this study was to conduct a meta-analysis that shows the influence of fiber on ultimate compressive strength and tensile strength of ultra-high performance concrete. The internet scholarly search engines and ScienceDirect article references were used to illustrate the papers concerning the experimental investigations of mechanical properties of ultra-high strength concrete with and without fiber with clearly, completely and comparative raw data. The normal concrete test results were dismissed from this search. Seven trials were identified based on the adopted inclusion and exclusion criteria above. The meta-analysis based on standardized mean difference was carried out on the basis of a fixed-effects model for the major outcomes of the ultimate compressive and tensile properties of ultra-high performance concrete. A total of 888 test specimens were enrolled in these seven trials. The combined analysis yielded a sign of a significant improvement in ultimate compressive strength and tensile strength of ultra-high strength concrete with fiber addition of 2% by concrete volume. The summary effect size of ultimate compressive strength was 2.34 while a more improvement in term of tensile strength with effect size of 2.64. By addition fiber of 2% provides a significant benefit in mechanical properties of ultra-high performance concrete.

The current study assessed the influence of Anti Stripping Agents (ASA), Ground Tire Rubber (GTR) and waste polyethylene terephthalate (PET) on performance behavior of binder and Stone Matrix Asphalt (SMA) mixtures. Through this paper, the 85/100 penetration grade bitumen was utilized as original bitumen. Also, three liquid ASA’s (ASA (A), ASA (B), ASA (C)) were used as a mixture modifier. For this purpose, softening point, penetration, rotational viscosity, Dynamic Shear Rheometer, Multi Stress Creep Recovery (MSCR) and Linear Amplitude Sweep (LAS) tests were implemented to investigate the rheological properties of modified bitumen. For evaluating the behavior of modified mixtures several tests such as; Resilient Modulus, Tensile Strength, dynamic creep, wheel track and four-point beam fatigue tests were implemented. Based on MSCR test results, utilization of mentioned polymers enhanced the elasticity of bitumens and therefore the permanent deformation resistance of binders increases. Also by the addition of PET percentage, the rutting resistance improves. Results indicated that utilization of ASAs, PET and Crumb Rubber (CR) enhance the Resilient Modulus (Mr), Indirect Tensile Strength (ITS), rutting resistance, fatigue life and Fracture Energy (FE) of asphalt mixtures. Also based on results, modification of binder by PET/CR with a ratio of 50%/50% and ASA (B) have the highest fatigue life which indicates that this mixture has highest resistance against fatigue cracking.

Humanity’s social and economic development has been challenged by a range of adversities over the millennia that have caused widespread and unimaginable suffering. At the same time, these challenges have forced humans to evolve more wisely, overcoming adversity through creativity and leading to advancements in science and technology, medicine, ethics and legal systems, and socio-political systems. The dynamics of risks and opportunities caused by COVID-19, in the built, cyber, social and economic environments, present opportunities for deepening our understanding of resilient and sustainable development and infrastructure. This article reflects on five lessons that COVID-19 is teaching us about what it means to develop sustainably through the lens of transportation: (1) sustainable development planning and analytical frameworks must be comprehensive, for long-term sustainability; (2) multi-modal transportation is a superior vision for sustainable development than any one particular mode; (3) tele-activities are part of an effective infrastructure sustainability strategy; (4) economic capital is critically important to sustainable development even when it is not a critical existential threat, and, (5) effective social capital is essential in global disaster resistance and recovery, and can and must be leveraged between fast-moving and slow-moving disasters. Resilient and sustainable infrastructure will continue to be critical to addressing evolving natural and man-made hazards in the 21^st Century.

This paper proposes a method for determining the bridge condition index (BCI) in concrete bridges, which is based on the views of bridge experts. First, eight indices were defined for a concrete bridge including structure, hydrology, safety, load impact, geotechnical and seismicity, strategic importance, facilities, and finally traffic and pavement. Each index consists of several sub-indices. Next, a series of questionnaires about the relative importance of indices and their sub-indices were prepared and distributed among bridge experts. Experts’ views were analyzed by Expert Choice software and the relative importance (weight) of each index and each sub-index was determined using the analytical hierarchy process (AHP). Then, based on experts’ views, an average score was assigned to each sub-index for any condition. Now the bridge inspectors can examine the bridge and determine the scores of sub-indices. Each index’s score is the sum of the weighted score assigned to its’ sub-indices and BCI is the sum of weighted scores assigned to indices. Higher values of BCI indicate a better condition. Therefore, bridges with lower BCI take priority in maintenance activities. To apply the proposed method, five bridges were selected in Semnan province, Iran, and BCI calculation of these bridges were conducted.

The importance of this study may be defined by using the smart techniques to earned value indicators of residential buildings projects in Republic of Iraq, only one development intelligent forecasting model was presented to predict Schedule Performance Index (SPI), Cost Performance Index (CPI), and To Complete Cost Performance Indicator (TCPI) are defined as the dependent. The approach is principally influenced by the determining numerous factors which effect on the earned value management, that involves Iraqi historical data. In addition, six independent variables (F1: BAC, Budget at Completion., F2: AC, Actual Cost., F3, A%, Actual Percentage., F4: EV, Earned Value. F5: P%, Planning Percentage., and F6: PV, Planning Value) were arbitrarily designated and satisfactorily described for per construction project. It was found that ANN has the capability to envisage the dust storm with a great accuracy. The correlation coefficient (R) has been 90.00%, and typical accuracy percentage has been 89.00%.

Facade elements are known to represent a building component with multiple performance parameters to satisfy. Among others, “advanced facades” take advantage of hybrid solutions, like the assemblage of laminated materials. In addition to enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lightening comfort and optimal thermal performance. This is the case of the structural solution developed in joint research efforts of the University of Zagreb and the University of Ljubljana, within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members, without sealing or bonded glass-to-timber surfaces. Laminated glass infilled timber frames are recognized as a new generation of structural members with relevant load-carrying capacity (and especially the enhancement of earthquake resistance of framed systems), but also energy-efficient and cost-effective solutions.

Marine clay deposits are commonly found worldwide. Considering the cost of dumping and the related environmental concerns, an alternative solution involving the reuse of soils that have poor conditions is crucial. In this research, the authors examined the durability of marine deposited clays and compiled a corresponding database. The use of slag alone as a binder, at any percentage, increased the accumulated mass loss (ALM) up to 2%. However, the use of lime as the third binder seemed to accelerate the chemical reactions associated with the hydration of clay and cementitious material and to enhance the chemical stability, i.e., samples that included both lime and slag experienced the same ALM as samples treated with cement only. Scanning electron microscopy analysis confirmed the durability improvements of these clays. The proposed unconfined compressive strength and accumulated mass loss relationship yielded practical approximation for the fine- and coarse-grained soils blended with up to three binders until 60 days of curing.

The damage caused by global warming is rapidly increasing, and its adverse effects become more evident with each passing day. Although it is known that the use of alternative binder materials in concrete would decrease this negative effect, reluctance to new composites continues. Waste use plays a vital role in sustainability studies. In this study, pure cement paste was prepared and enriched with carbon fiber. This study investigated the wide range of volume fraction of carbon fiber in cement-based composites. Two different industrial wastes, marble dust, and bottom ash were chosen and mixed with cement and four different (0.3%, 0.75%, 1.5%, and 2.5%) carbon fiber volume fractions. Based on physical, mechanical, and durability tests at 7, 28, and 56-days of curing, the composites were resistant to sulfate and seawater attack. The 0.75% carbon fiber addition seems to be an optimum volume percentage beyond which both physical and mechanical properties were adversely affected. The composites with 0.75% carbon fiber have reached 48.4 MPa and 47.2 MPa at 56-days of curing for marble dust and bottom ash mixture groups, respectively.

Extinction of natural resources builds up pressure on governments to invest in research to find more sustainable resources for construction sector. Earlier studies on mortar and concrete show that bottom ash and basalt fiber are independently alternative binder in the concrete sector. This study aims to use bottom ash and basalt fiber blends as alternative novel-based composites in pure cement paste. Strength and durability properties of two different percentages of bottom ash (40% and 50%) and three volume fractions of basalt fiber (0.3%, 0.75%, and 1.5%) were used at three curing periods (7, 28, and 56 days). In order to measure physical properties of the basalt-reinforced bottom ash cement paste composites flowability, dry unit weight, porosity and water absorption measurements at 7, 28, and 56 days of curing were performed. Furthermore, mechanical properties of composites determined by unconfined compressive strength and flexural strength tests. Finally, to assess the durability sulfate-resistance and seawater-resistance tests have been performed on composites at 28 and 56 days of curing. Results showed that addition of basalt fiber improves physical, mechanical and chemical stability properties of paste up to a limiting basalt fiber addition (0.3% volume fraction) where above an adverse effect have been monitored. It is clear that observed results can lead to development of sustainability strategies in the concrete industry by utilizing bottom ash and basalt fiber as an alternative binder.

Rapid Visual Screening (RVS) is a procedure that estimates structural scores for buildings and prioritize their retrofit and upgrade requirements. Despite the speed and simplicity of RVS, many of the collected parameters are non-commensurable and include subjectivity due to visual observations. It might cause uncertainties in the evaluation, which emphasizes the use of a fuzzy-based method. This study aims to propose a novel RVS methodology based on the interval type-2 fuzzy logic system (IT2FLS) to set the priority of vulnerable building to undergo detailed assessment while covering uncertainties and minimizing their effects during evaluation. The proposed method estimates the vulnerability of a building, in terms of Visual Damage Index, considering the number of stories, age of building, plan irregularity, vertical irregularity, building quality, and peak ground velocity, as inputs with a single output variable. Applicability of the proposed method has been investigated using a post-earthquake damage database of 28 reinforced concrete buildings from the Bingöl earthquake in Turkey.

In the field of pavement engineering, the determination of the mechanical characteristics is one of the essential process for reliable material design and highway sustainability. Early determination of mechanical characteristics of pavement is highly essential for road and highway construction and maintenance. Tensile strength (TS), compressive strength (CS) and flexural strength (FS) of roller compacted concrete pavement (RCCP) are very crucial characteristics as they are necessitated for many data from mixture proportions as input variables. In this research, the classification-based regression models named Random Forest (RF), M5rule model tree (M5rule), M5prime model tree (M5p) and Chi-square Automatic Interaction Detection (CHAID) are developed for simulation of the mechanical characteristics of RCCP. A comprehensive and reliable dataset comprising 621, 326 and 290 data records for CS, TS and FS experimental cases extracted from several open sources over the literature. The mechanical properties are developed based on influential inputs combination that processed using Principle Component Analysis (PCA). The applied PCA method as feature selection is specified that volumetric/weighted content forms of experimental variables (e.g., coarse aggregate, fine aggregate, supplementary cementitious materials, water and binder) and specimens’ age are the most effective inputs to generate the better performances. Several statistical metrics are measured to evaluate proposed classification-based regression models. RF model revealed an optimistic classification capacity of the CS, TS and FS prediction of the RCCP in comparison with the CHAID, M5rule, and M5p models. The research is extended for the results verification using Monte-carlo model for the uncertainty and sensitivity of variables importance analysis. Overall, the proposed methodology indicated a reliable soft computing model that can be implemented for the material engineering construction and design.

In an attempt to improve the quality of the agricultural drain in Egypt for its reuse again in the irrigation, low cost solution such as sand filter along with/ without other filtration media have been used in this research, As a result of that, pilot plant of sand filter mixed with other filtration media was tested for its ability to improve the sand performance in removing the suspended solids and organic matters from agricultural drain water of the Belbeis drain (in Sharkia governorate in Egypt). Only sand compared with sand with sponge and sand with Liyan Nanfang activated carbon (L.N.A.C) have been tested to find the optimum mixing sand/ medium ratio &optimum infiltration rate. The work has been done on four runs. It was found that sand mixed with sponge gave the best removal efficiency compared to that of the sand only and the sand mixed with L.N.A.C. The results presented that the concentration of CODt, CODsol and TSS was reduced from 125, 47 and 162 mg/l to 44, 34 and 28 mg/l respectively at optimum infiltration rate of 2 m³/m²/d for sand mixed with sponge.

The distributed fiber optic strain measurement based on Rayleigh scattering has recently become increasingly popular in automotive or mechanical engineering for strain monitoring and in the construction industry, especially structural health monitoring. This technology enables the monitoring of strain along the entire fiber length. This article addresses integrating optical fibers of different coatings into the concrete matrix to measure the shrinkage deformations. However, previous studies do not give a clear statement about the strain transfer losses of fiber optic sensors in this application. In this context, three different coating types were investigated regarding their strain transfer. The fibers were integrated into fine-grained concrete prisms, and the shrinkage strain was compared with a precise dial gauge. The analysis shows a high correlation between the reference method and the fiber measurement, especially with the Ormocer coating. The used acrylate coating is also consistent in the middle area of the specimen but requires a certain strain introduction length to indicate the actual strain. The main result of this study is a recommendation for fiber coatings for shrinkage measurement in fine-grain concretes using the distributed fiber optic strain measurement. In addition, the advantages and disadvantages of the measurement method are presented.

This work evaluates the surface water quality in terms of physico-chemical parameters of the Brahmani River, Odisha using statistical analysis involving the calculation of correlation coefficient and regression equation. Besides this, the work also highlights and draws attention towards the “Water Quality Index” in a simplified format which may be used at large and could represent the reliable picture of water quality. Surface water quality data is taken from OSPCB of various location i.e. Panposh D/S, Rourkela D/S, Rengali, Talcher U/S, Kamalanga D/S, Bhuban, Pattamundai and was assessed for summer, monsoon, winter for the years 2011, 2012, 2013, 2014 and 2015. Average of values, minimum of values and maximum of values of water quality parameters were obtained seasonally over the above mentioned years. Besides this, the standard deviation for the water quality parameters was also obtained for water quality parameters namely pH, Temperature, DO, TDS, Alkalinity, EC, Na+, Ca2+, Mg2+, K+, F-, Cl-, NO3-, SO42- and PO42-. Seasonal changes in various physical and chemical parameters were analysed.The values obtained were compared with the guideline values for drinking water by Bureau of Indian Standard (BIS). A systematic correlation and regression study is carried out for three seasons, showed linear relationship among different water quality parameters. This provides an easy and rapid method of monitoring water quality. Highly significant (0.8< r <1.0), moderately significant (0.6< r <0.8) and significant (0.5< r <0.6) correlations between the parameters have been worked out. High correlation coefficient has been observed between TDS,EC-Na+, Ca2+, Cl-, SO42- ; Na+- Cl-. From the collected quantities, certain parameters were selected to derive WQI for the variations in water quality of each designated sampling site. WQI of Brahmani River ranged from 36.7 to 44.1 which falls in the range of good quality of water.Panposh D/S and Rourkela D/S showed poor water quality in summer and winter season. It is shown that WQI may be a useful tool for assessing water quality and predicting trend of variation in water quality at differentlocations in the Brahmani River.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

The operation feasibility of small hydropower plants in mountainous sites is subjected to the run-of-river flow which is also depending on a high variability in precipitation and snow cover. Moreover, the management of this kind of systems has to be performed with some particular operation conditions of the plant (e.g. turbine minimum and maximum discharge) but also some environmental flow requirements. In this context, a technological climate service is conceived in tight connection with end users, perfectly answering the needs of the management of small hydropower systems in a pilot area, and providing forecast of river streamflow together with other operation data. This paper presents an overview of the service but also a set of lessons learnt related to features, requirements and considerations to bear in mind from the point of view of climate services developers. In addition, the outcomes give insight into how this kind of services could change the traditional management (normally based on the past experience), providing a probability range of future river flow based on future weather scenarios according to the range of future weather possibilities. This highlights the utility of the co-generation process to implement climate services for water and energy fields but also that seasonal climate forecast could improve the business as usual of this kind of facilities.

Dynamic analyses and seismic assessments of multi-storey buildings at urban level require large-scale simulations and computational procedures based on simplified but accurate numerical models. At this aim the present paper propos-es an equivalent non-uniform beam-like model, suitable for the dynamic analysis of buildings with asymmetric plan and non-uniform vertical distribution of mass and stiffness. The equations of motion of this beam-like model, which pre-sents only shear and torsional deformability, are derived through the application of Hamilton’s principle. The linear dy-namic behaviour is evaluated by discretizing the continuous non-uniform model according to a Rayleigh-Ritz approach based on a suitable number of modal shapes of the uniform shear-torsional beam. In spite of its simplicity, the model is able to reproduce the dynamic behaviour of low- and mid-rise buildings with a significant reduction of the computa-tional burden with respect to that required by more general models. The efficacy of the proposed approach has been tested, by means of comparisons with linear FEM simulations, on three multi-storey buildings characterized by different irregularities. The satisfactory agreement, in terms of natural frequencies, modes of vibration and seismic response, proves the capability of the proposed approach to reproduce the dynamic response of complex spatial multi storey frames.

The climate covers a series of events that deeply affect human life. It is possible to understand these events through spatial and statistical analyzes. Today, climate change, which is one of the most important of these events and the impact factors of consequences of this change, become a current issue. Drought is cited as one of the consequences of climate change and it is important to examine it with various methods as it can give negative results to both the economy and the nature. In this study, the drought status of the regions where these stations are located and the effects of drought on climate change were statistically calculated and evaluated using Standardized Precipitation Index (SPI), Percentage of Normal Index (PNI), Aridity Index (AI) and Standardized Precipitation -Evopotranspiration Index (SPEI). The precipitation data from 1981 to 2010 were obtained from Cihanbeyli, Karapınar, Çumra, Seydişehir, Kulu, Ereğli, Niğde, Karaman, Beyşehir and Aksaray meteorology stations affiliated to Turkish State Meteorological Service. At the same time, factor analysis and validity-reliability analysis were conducted to test the computability of the indices used in the study as a single index and to determine the reliability of the operations. While using exploratory factor analysis, Kaiser-Meyer-Olkin (KMO) test and Barlett test for factor analysis; Cronbach's alpha coefficient was used for reliability analysis. In our study, K-Means Cluster Analysis method was performed to determine the cutoff values of indices. According to the result of cluster analysis for the new (common) index, new clusters were created and ANOVA test was conducted to determine whether there was a difference between clusters.

Transition between free-surface and pressurized flows is an crucial phenomenon in many hydraulic systems, including water distribution systems, urban drainage systems, etc. During the transition, the force exerted on the structures changes drastically, thus it is meaningful to simulate this process. However, severe numerical oscillations are widely observed behind filling-bores, causing unphysical pressure variations and even computation failure. In this paper, some oscillation-suppressing approaches are reviewed and evaluated on a benchmark model. Then a new oscillation-suppressing approach is proposed to admit numerical viscosity when the water surface is at proximity of conduct roof which has first order accuracy. This approach adds numerical viscosity when water surface is at the proximity of conduct roof. It can sufficiently suppress numerical oscillations under an acoustic wave speed of 1000m/s and is simple to apply. In comparison with two experiments, the simulation results of this method show good agreement and little numerical oscillations. The results in this paper can help readers to choose an appropriate oscillation-suppressing method to improve the robustness and accuracy of flow regime transition simulations.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

A large number of bridges are designed and built without considering seismic actions and, differently from buildings, there are currently no comprehensive guidelines to evaluate existing bridges without performing, as in the well known incremental dynamic analysis (IDA), complex non linear dynamic analyses (RHA). Bridges are structurally very different from building but, at the same time, are sensitive to higher modes as well as many multi-storey buildings that inspired innovative pushover procedures such as the well known modal pushover analysis (MPA). In the present study the incremental modal pushover analysis (IMPA), a pushover based approach already proposed and applied on buildings by the same authors, is revised and proposed for bridges (IMPAβ). IMPAβ accounts for the effects of higher modes in order to accurately estimate the seismic response of bridges; the effect of higher modes is considered by introducing a suitable number of modes to ensure the participation of a predefined total effective modal mass. The efficiency of the proposed method is demonstrated by conducting a study on two bridges, one regular and one irregular, and the IDA analysis is employed as reference solution. Numerical results indicate good accuracy of the proposed method in assessing the seismic response and a very good accuracy if compared to other available pushover procedures available in the literature.

Escherichia coli or E. coli is a member of the fecal coliform group and is a more specific indicator of fecal contamination than other fecal coliform species, its presence indicate possibly presence of harmful bacteria which will cause diseases and it also suggests the extent as well as the nature of the contaminants. E. coli bacteria able to survive in water for 4 – 12 weeks and at present, it appears as an indicator to provide the accurate bacterial contamination of fecal matter in drinking water, because of the availability of simple, affordable, fast, sensitive and exact detection techniques. According to the laboratory experiment based techniques, 24 - 48 hours are required for the bacterial concentration to be reported. So, there is a necessity for continuous monitoring. Techniques for detection of many pathogenic bacterial strains are not yet available, sometimes days to weeks are required to get the results. To overcome the difficulties, expensive and time-consuming techniques are required to detect, count and identify the presence of specific bacterial strain. Public health relies on online monitoring of water quality that depends majorly on examination of fecal indicator bacteria, thus protection of health requires fecal pollution indicator so that it is not required to analyze drinking water to overcome the problems associated with waterborne diseases. This paper will brief the classification, sources, survival of E. coli bacteria and its correlation with basic water quality parameters in water sources.```

This study was conducted generally by aiming assessment of the hydraulic performance of water distribution systems of Addis Ababa Science and Technology University (AASTU). In line with the main objective, this study addressed, (1) pinpointing problems of existing water supply versus demand deficit (2) evaluating the hydraulic performance of water distribution system using water GEMS and (3) recommended alternative methods for improving water demand scenarios. The University’s water supply distribution network layout was a looped system and the flow of water derived by both gravity and pressurized system. The gravity flow served for the academic and administrative staffs whereas the pressurized system of the network fed the students dormitories, cafeteria’s etc. The study revealed the existence of unmet minimum pressure requirement around the student dormitories which accounts 25.64% below the country’s building code standard during the peak hour consumption. The result of the water demand projection showed an increment of 2.5 liter per capita demand (LPCD) in every five years. Hence, first, the university’s water demand was projected and then hydraulic parameters such as; pressure, head loss and velocity were modeled for both the existing and the improved water supply distribution. The finding of the study was recommended to the university’s water supply project and institutional development offices for its future modification and rehabilitation works.

This paper presents a new numerical method for multiscale modeling of composite materials. The new numerical model, called DECM, consists in a DEM (Discrete Element Method) approach of the Cell Method (CM) and combines the main features of both the DEM and the CM. In particular, it offers the same degree of detail as the CM, on the microscale, and manages the discrete elements individually such as the DEM—allowing finite displacements and rotations—on the macroscale. Moreover, the DECM is able to activate crack propagation until complete detachment and automatically recognizes new contacts. Unlike other DEM approaches for modeling failure mechanisms in continuous media, the DECM does not require prior knowledge of the failure position. Furthermore, the DECM solves the problems in the space domain directly. Therefore, it does not require any dynamic relaxation techniques to obtain the static solution. For the sake of example, the paper shows the results offered by the DECM for axial and shear loading of a composite two-dimensional domain with periodic round inclusions. The paper also offers some insights into how the inclusions modify the stress field in composite continua.

Earthquake is among the most devastating natural disasters causing severe economic, environmental, and social destruction. Earthquake safety assessment and building hazard monitoring can highly contribute to urban sustainable development through identification and insight into optimum materials and structures. While the vulnerability of structures mainly depends on the structural resistance, the safety assessment of buildings can be highly challenging. In this paper, we consider Rapid Visual Screening (RVS) method which is a qualitative procedure for estimating structural scores for buildings suitable for medium- to high-seismic cases. This paper presents an overview of the common RVS methods, i.e., FEMA P-154, IITK-GGSDMA, and EMPI. To examine the accuracy and validation, a practical comparison is performed between their assessment and observed damage of reinforced concrete buildings from a street survey in the Bingöl region, Turkey, after the 11 May 2003 earthquake. The results demonstrate that the application of RVS methods for preliminary damage estimation is a vital tool. Furthermore, the comparative analysis showed that FEMA P-154 creates an assessment that overestimates damage states and is not economically viable while EMPI and IITK-GGSDMA provide for more accurate and practical estimation, respectively.

In order to realize the sustainable utilization of water resources and the sustainable development of economy, the evaluation index system of water use efficiency system and economic development system was constructed. Entropy weight method and comprehensive evaluation method were adopted to determine the index weights and conduct comprehensive evaluation for the two systems. The coupling coordination model was used to calculate the coupling degree, coordination degree and coupling coordination degree of the two systems. The annual coupling stage and coupling coordination intensity of the two systems were analyzed and determined. The results showed that the comprehensive evaluation values of both water use efficiency system and economic development system in Jinan City increased greatly from 2008 to 2017, and showed a changing trend of ups and downs. The two systems were in the antagonistic stage, and were gradually approaching the running-in stage, indicating that they were in the state of common development. The coupling coordination degree of the two systems gradually increased in waves, progressed from the moderately to the highly coordinated coupling. In the future, if the water control path appropriate to Jinan City can be explored actively, the water-saving kinetic energy of economic development can be increased constantly, and the linkage effect between economic development and water resources utilization can be given full play to, the two systems will be in the orbit with the benign interaction and healthy harmonious development.

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

Particle size can pose a challenge to random embankment compaction control methods, where practical techniques have hardly been developed and procedural control is used instead. In order to develop new quality control procedures for slate random fill, the necessary fieldwork and laboratory tests were carried out. This involved the revision of certain methods such as the wheel-tracking or topographic settlement tests. More than six hundred in-situ density and moisture content measurements were carried out for this research. In addition, more three hundred topographic settlements and three hundred wheel-tracking carriage tests were performed. The quality control processes were completed with more than thirty plate bearing tests. Possible evidence of statistical correlations between compaction control tests were identified. An analysis of variance (ANOVA) was performed. When testing proved relationships between them, the replacement of one of them by the other was assessed by deduction. Finally, the study suggests new procedures for compaction quality control of random slate fill used in crown area.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

Densimetric Froude (Fr) is the minimum velocity required to prevent sediment deposition in pipes. Prediction of Fr is of utmost importance in numerous applications in civil engineering. In this paper through using a new hybrid method. Genetic Algorithm (GA) is used for optimum selection of membership functions of Adaptive Neuro-Fuzzy Inference System (ANFIS), and Singular Value Decomposition (SVD) method is used to compute the linear parameters of ANFIS’s results section (ANFIS-GA/SVD). Also, two different target functions are known as training error (TE) and prediction error (PE) by Pareto curve, the trade-off between these functions is selected as the optimal modeling point. First, different models will be presented using the parameters affecting Fr prediction, classifying them in different groups; then the Fr parameter will be predicted for all the different models through utilizing three different sets of data and the ANFIS-GA/SVD technique. The results of the models indicate that the best Fr prediction is obtained when independent parameters such as volumetric sediment concentration (CV), ratio of median diameter of particle size to pipe diameter (d/D), ratio of median diameter of particle size to hydraulic radius (d/R) and overall friction factor of sediment (λs) use as input variables in prediction of Fr. A sensitivity analysis is also conducted for the purpose of examining the effect of each of the dimensionless parameters on Fr prediction accuracy. Comparing the results of the suggested models with the existing regression-based equations shows that ANFIS-GA/SVD (R²=0.986, MAPE=4.397, RMSE=0.206, SI=0.053, ρ=0.026, BIAS=-0.025) is more accurate than the rest of the models.

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

A numerical study for the effect of crest width, breaking parameter and trunk permeability on hydrodynamics and flow behavior in the vicinity of rubble-mound, permeable, zero-freeboard breakwaters (ZFBs) is presented. The modified two dimensional Navier-Stokes equations for two-phase flows in porous media with a Smagorinsky model for the subgrid scale stresses were solved numerically. An immersed-boundary/level-set method was used. The numerical model was validated for the cases of wave propagation over a submerged impermeable trapezoidal bar and over a low-crested permeable breakwater. Five cases of breakwaters were examined, and the main results are: (a) The size of the crest width, B, does not notably affect the wave reflection, vorticity and currents in the seaward region of ZFBs, while wave transmission, currents in the leeward side, and mean overtopping discharge, all decrease with increasing B. A non-monotonic behavior of the wave setup is also observed. (b) As the breaking parameter decreases, wave reflection, transmission, currents, mean overtopping discharge, and wave setup decrease. This observation is also verified by relevant empirical formulas. (c) As the ZFB trunk permeability decreases, an increase of the wave reflection, currents, wave setup, and a decrease of wave transmission and mean overtopping discharge is observed.

Structural displacement is an important metric for assessing structural conditions because it has a direct relationship with the structural stiffness. Many bridge displacement measurement techniques have been developed, but most methods require fixed reference points in the vicinity of the target structure which limits field implementations. A promising alternative is to use reference-free measurement techniques that indirectly estimate the displacement by using measurements such as acceleration, and strain. This paper proposes novel reference-free bridge displacement estimation by the fusion of single acceleration with pseudo-static displacement derived from co-located strain measurements. First, we propose a conversion of the strain at the center of a beam into displacement based on the geometric relationship between strain and deflection curves with reference-free calibration. Second, an adaptive Kalman filter is proposed to fuse the displacement generated by strain with acceleration by recursively estimate the noise covariance of displacement from strain measurements which is vulnerable to measurement condition. Both numerical and experimental validations are presented to demonstrate the efficiency and robustness of the proposed approach.

This paper addresses the study of the stress field in composites continua with the multiscale approach of the DECM (Discrete Element modeling with the Cell Method). The analysis focuses on composites consisting of a matrix with inclusions of various shapes, to investigate whether and how the shape of the inclusions changes the stress field. The purpose is to provide a numerical explanation for some of the main failure mechanisms of concrete, which is precisely a composite consisting of a cement-based matrix and aggregates of various shapes. Actually, while extensive experimental campaigns detailed the shape effect of concrete aggregates in the past, so far it has not been possible to model the stress field within the inclusions and on the interfaces accurately. The reason for this lies in the limits of the differential formulation, which is the basis of the most commonly used numerical methods. The Cell Method (CM), on the contrary, is an algebraic method that provides descriptions up to the micro-scale, independently of the presence of rheological discontinuities or concentrated sources. This makes the CM useful for describing the shape effect of the inclusions, on the micro-scale. When used together with a multiscale approach, it also models the macro-scale behavior of periodic composite continua, without losing accuracy on the micro-scale. The DECM uses discrete elements precisely to provide the CM with a multiscale approach.

The high volume of water in molasses has made this study serious. The reason is that using molasses as a partial replacement without treatment significantly affects the rheological properties of the neat bitumen and increases the likelihood of moisture susceptibility of the hot-mix asphalt (HMA) pavement structure and create fractures of aggregate particles. Therefore, to use molasses as a partial replacement without affecting the structural integrity of the pavement, this study proposed a treatment method before blending it with petroleum-based bitumen. A series of experiment was conducted to accomplish the objective of this paper, including convectional tests, Fourier transform infrared (FTIR) test, amplitude and frequency sweep test, performance grade (PG) determination test, and multiple stress creep recovery (MSCR) tests. The IR spectra show that carbonyl index decreased with increasing molasses percent. There was PG improvement from the control grade to PG64 and PG70 when the base binder modified with 5-20% molasses and aged with rollingl thin film oven (RTFO) respectively. At the temperature 58oC nonrecoverable creep compliance at 3.2 kPa (Jnr3.2kPa) was decreased for each percent replacement. This led to improving the rutting potential. As well, at a temperature of 64oC the Jnr value was decreased only for 5% replacement, and then the Jnr value was gradually increased for the remaining percent replacement. Overall, this study revealed that treated molasses can be used as a partial replacement to enhance the rheological properties of the base bitumen and thus it can potentially be used to produce a sustainable bio-asphalt binder.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

Green infrastructure systems are often overdesigned. This may be a byproduct of static sizing (e.g., accounting for a design storm’s runoff volume but not exfiltration rates) or may be deliberate (e.g., buffering against performance loss through time). Regardless, overdesign may compromise plants’ access to water in systems where soil pits are embedded in infiltration beds. It could raise the storm size required for water to reach soil pits, reducing water availability between storms, which could ultimately induce plant physiological stress. This study investigated the hydrological dynamics and water relations of a tree trench system suspected to have been overbuilt and identified factors contributing to, compounding, and mitigating the risk of plant stress. Results provided strong evidence that the abovementioned processes played out. Water in the infiltration bed reached soil pits only once in three years, with that event occurring during a hydrant release. Moreover, minimal water was retained in the soil pit during the event due to the hydraulic properties of the soil media. Through a growing season, one of the two tree types frequently experienced water stress, while the other did so only rarely. These contrasting responses can likely be attributed to roots either being largely confined to the soil pits or reaching a deeper water source. Implications of these results for green infrastructure design are considered.

During the casting in a warmer tropical temperature, a setting time delay is required to maintain the workability of the concrete, commonly achieved by the addition of admixtures i.e. silica fume (SF), fly ash (FA), and Plastrocrete®. However, high sugar content Coca-Cola in niche conditions is proposed as an ingredient for delaying concrete setting time in combination with conventional admixtures. This research aims to compare the setting time of admixtures from Coca-Cola and Plastocrete® RT6 plus in concrete mixing with control data of concrete mixed with SF or FA. The second aim is to measure the compression strengths between combinations of Coca-Cola and Plastocrete® RT6 plus. Concretes were produced with admixtures of SF, FA, Plastocrete® RT6plus, or Coca-Cola. The concrete used to control was f'c20 and f'c 25, while other concrete mixes were produced with the addition of Coca-Cola at 0.15% from the weight of cement at variation of moisture treatments. The first method to produce concrete (f'c20+Plas0.23%+Cola0.15% and f'c25+Plas0.23%+Cola0.15%) did not employ water reduction. The second concrete productions (f'c25+Plas0.46%+Cola0.15% and f'c25+Plas0.46%+Cola0.15%) reduced the addition of water at 8.8% (v/w). The first concrete production method had a setting time 44% longer than control. The reduced water concrete in the second productions had a setting time 34% longer than control. Meanwhile, the Plastocrete® RT6 Plus admixture with the reduced water delayed the concrete setting time by 26% longer than control. The delayed setting time of Plastocrete® RT6 Plus admixture with reduction of water was shorter than in the treatment with Coca-Cola. The combination of the addition of Coca-Cola with Plastocrete® RT6 plus by reducing the amount of adding Coca-Cola to 0.10% with Plastocrete® RT6 plus can delay concrete setting time by 51% longer than normal concrete and increase concrete compressive strength by 13% higher than normal concrete. Mixing Coca-Cola with Plastocrete® RT6 plus not only provided an optimal delay effect on setting time but also significantly increase the compressive strength that was desired during the casting in warm tropical weather applied in building construction of Mulawarman University, Samarinda, Indonesia.

Understanding of reflection characteristics of coastal seawalls is crucial for design. Wave reflection can cause difficulties to small vessel manoeuvring at the harbour entrance and constitute damaging scouring at the toe of coastal structures. Previous studies have considered reflection characteristics of coastal seawalls under wind-generated random waves without paying attention to the effects of wave bimodality created by the presence of swell waves. The present study focuses on the influence of random wave bimodality on reflective characteristics of coastal seawalls. More than eight hundred experimental tests have been conducted to examine the reflection performance of impermeable sloping seawalls under bimodal waves. Reflection coefficients were computed from each test. Analysis of results suggests that both unimodal and bimodal waves give similar reflection characteristics. However, the reflection coefficient in bimodal sea states seems to be more prolonged than in the unimodal sea states. It was found that the reflection coefficient of coastal seawalls is strongly influenced by the seawall slope, the wave steepness, relative water depth, and the surf similarity parameters. A new empirical reflection equation to describe the influence of wave bimodality on the reflection characteristics of coastal seawalls has been formulated based on this study.

Buildings use 30-40 % of all energy resources and are thus their main consumers in modern society. Moreover, buildings require a vast amount of different raw materials. During the last two decades, several green building certifications have been created in order to consider social, economic and environmental aspects of sustainability of buildings. One of the most famous and widely used of these certifications is Leadership in Energy and Environmental Design (LEED). So far, the use of LEED has concentrated in the US and other developed countries. One reason that restricts the use of this point-based system certification in developing countries is the limited data about its costs. In this study, the extra cost of the certification process will be evaluated besides the changes needed in the design of the building to reach the points required by LEED. At the first stage, the number of points the case study earns in its current format (Scenario 1) were found out, then the cost difference of getting either the Certified (Scenario 2) or Silver (Scenario 3) level LEED certification for the building was studied. It was found that besides some technical considerations, filling the criteria of the Certified and Silver level increases the total costs of construction by 3.4% and 5.9%. Further improvement of the building’s energy efficiency would enable the attainment of a higher-level certification. The results of the study could help to promote the use of green building certifications in Western Asia.

With advances in Building Information Modeling (BIM), Virtual Reality (VR) and Augmented Reality (AR) technologies have many potential applications in the Architecture, Engineering, and Construction (AEC) industry. However, the AEC industry, relative to other industries, has been slow in adopting AR/VR technologies, partly due to lack of feasibility studies examining the actual cost of implementation versus an increase in profit. The main objectives of this paper are to understand the industry trends in adopting AR/VR technologies and identifying gaps within the industry. The identified gaps can lead to opportunities for developing new tools and finding new use cases. To achieve these goals, two rounds of a survey at two different time periods (a year apart) were conducted. Responses from 158 industry experts and researchers were analyzed to assess the current state, growth, and saving opportunities for AR/VR technologies for the AEC industry. The findings demonstrate that older generations are significantly more confident about the future of AR/VR technologies and they see more benefits in AR/VR utilization. Furthermore, the research results indicate that Residential and commercial sectors have adopted these tools the most, compared to other sectors and institutional and transportation sectors had the highest growth from 2017 to 2018. Industry experts anticipated a solid growth in the use of AR/VR technologies in 5 to 10 years, with the highest expectations towards healthcare. Ultimately, the findings show a significant increase in AR/VR utilization in the AEC industry from 2017 to 2018.

Local thermal comfort (TC) and draught rate (DR) has been studied widely. There has been more meaningful research performed in controlled boundary condition situations than in actual work environments involving occupants. TC conditions in office buildings in Estonia have been barely investigated in the past. In this paper, the results of TC and DR assessment in five office buildings in Tallinn are presented and discussed. Studied office landscapes vary in heating, ventilation and cooling (HVAC) system parameters, room units and elements. All sample buildings were less than six years old, equipped with dedicated outdoor air ventilation system and room conditioning units. The on-site measurements consisted of TC and DR assessment with indoor climate questionnaire (ICQ). The purpose of the survey is to assess the correspondence between HVAC design and the actual situation. Results show, whether and in what extent the standard-based criteria for TC is suitable for actual usage of the occupants. Preferring one room conditioning unit type or system may not guarantee better thermal environment without draught. Although some HVAC systems observed in this study should create the prerequisites for ensuring more comfort, results show that this is not the case for all buildings in this study.

Joints between walls are very important for structural analysis of each masonry building at the global and local level. This issue was often neglected in case of traditional joints and relatively squat walls. Nowadays the issue of wall joints is becoming particularly important due to the continuous strive for simplifying structures, introducing new technologies and materials. Eurocode 6 and other standards (USA, Canadian, Chinese, and Japanese) recommend inspecting joints between walls, but no detail procedures have been specified. This paper presents our own tests on joints between walls made of autoclaved aerated concrete (AAC) masonry units. Tests included reference models composed of two wall panels joined perpendicularly with a masonry bond (6 models), traditional steel and modified connectors (12 models). A shape and size of test models and structure of a test stand were determined on the basis of the analysis of the current knowledge, pilot studies and numerical analyses of FEM. The analysis referred to the morphology and failure mechanism of models. Load-displacement relationships for different types of joints were compared and obtained results were referred to results for reference models. A mechanism of cracking and failure was found to vary, and clear differences in behaviour and load capacity of each type of joints were observed. Individual working phases of joints were determined and defined, and the empirical approach was suggested to determine forces and displacement of wall joints.

Information and communication technologies play an increasingly important role in the process of acquiring knowledge from a territory and managing it at different scales. ICTs allow a rapid diffusion of data not only through institutional channels but also through social networks where the smart community share experiences and perceptions. In this sense, ICTs become strategic to support the promotion of sustainable tourism development of territories. An important tool to implement it, can be a circular smart dashboard, a decision support system in which the digital data are organized and processed to produce an information output, to be used, after the evaluation by the decision makers, as a new input for the system. The present paper deals with a wider research the authors are involved in, related to the reconversion and valorization of a former mining area towards slow tourism, as the Santa Barbara Walk (SBW), an ancient mining route in the Sulcis Iglesiente area (Sardinia, Italy) . In particular, we here focus on the design proposal of a dashboard, capable of organizing information concerning the main features of the walk, in order to facilitate a shared governance for an effective tourism promotion. The paper is based on a thorough recognition of the main characteristics of the Walk, both the material ones and the digital, immaterial ones. The SBW represents in fact a network connecting the main points of interest along the Walk. On the contrary, its digital network – consisting of intangible infrastructure and flows - is however fragmented in terms of policies and contents Also a state of disorganization in slow tourism promotion activities can be observed. The goal of this paper is to present and analysis of the area, and to propose an evaluation and planning tool as the design of a circular dashboard of the SBW.

The underground injection and geological sequestration of carbon dioxide (CO₂) is a promising approach for reducing the levels of CO₂ in the atmosphere. To mitigate the leakage of CO₂ resulting from natural fracture networks in rock masses, the sequestration process is commonly accompanied by the injection of reactive Portland cement representing a coupled hydro-chemo-mechanical process. In this work, a numerical approach based on the unified pipe network method (UPM) is presented that considers the coupled permeation and diffusion processes with chemical precipitation. Most input parameters are derived from the published literature. The proposed approach is validated through a comparison with analytical solutions, which are applied to simulate the CO₂ sequestration process in a fractured rock mass. The results indicate that the long-term sequestration effect, which is highly influenced by the fracture distribution, can be captured effectively by the model. Consequently, the presented approach can assist engineers in properly designing the arrangement of boreholes and determining the concentration of the grouting material.

The objective of this study is to conduct a mineralogical and chemical characterization of the mortars Roman archaeological site of Volubilis to rebuild spare mortars for restoration. We take samples of mortar, broken tile palate garden, and pavement mosaic Falavius Germanus houses. The analysis by X-ray diffraction reveals the coarse mortar Flavius Germanus is made of quartz and calcite with feldspar and probably, mica and dolomite in small amounts. The binder end is formed calcite and quartz. However, the broken tile mortar is formed by coarse particles, clay base mixed with a binder phase dominated by calcite. These results allowed us to reformulate spare mortars for the restoration of damaged Roman mosaics. The mortars are made up by 63.6% of lime and 36.4% of sand(with 4.19% of large grain, 71, 04% of coarse sand, 24.22%, of fine sand and 0.55% fines parts).The performance of these mortars was tested by mechanical testing.

As is well known, the main contribution of the FRP strips to the strength of load-bearing walls is an improvement in the in-plane strength. This paper deals with the possibility of applying the FRP strips in way to modify the strengthening mechanism of the FRP reinforcing system, from an in-plane to an out-of-plane strengthening mechanism. In order to achieve this goal, a second reinforcement system – derived from the CAM system (Active Confinement of Masonry) – provides connections between the FRP strips placed on the opposite sides of the wall. This new strengthening technique – called the straps/strips technique – establishes a stiffness constraint that forces the opposing FRP strips to behave like two flanges of an FRP I-beam embedded in the wall. Consequently, the use of FRP strips also improves the flexural strength of the wall. The present paper briefly summarizes the results obtained in previous works with the straps/strips technique and proposes an improvement of this strengthening technique, based on some weak-points emerged in the early experimentations. The paper also shows the results of a further experimental test, performed with the improved straps/strips technique. Finally, the similarity between FRP strips with transversal connection and concrete wythes of a sandwich panel with flexible connectors leads to interpret the behavior of the ideal I-beam in terms of composite action established between the FRP strips. This paves the way for analytical modeling of the straps/strips technique.

Estimating heat emission losses of heating systems is an important task of energy efficiency assessments in buildings. To this aim, the present international standards contain tabulated values for different emitter and control system configurations, without however explaining how to compute the effect of increased setpoint temperatures on the system losses. Moreover, the effects of each component are treated as independent, while e.g. vertical stratification and temperature control of the system are cross-related. In this paper we attempt to fill this gap by proposing a calculation method to calculate the product category specific setpoint variations for space heating emitters, accounting for the overall heat balance in the enclosure and including the cross-correlations of each component as well. The emission losses of a heating system are computed using a temperature setpoint variation method that is imposed on annual energy calculations. This complements the procedure presented in the Standard EN15316-2, also providing the possibility to use product-specific values of setpoint variations instead of tabulated values. As the main finding of the study, the calculation process is defined for a European Reference Room, namely for a specific enclosure that allows an accurate and transparent evaluation of the total setpoint variation. The product-specific values of setpoint variations are calculated from measured vertical stratification and control parameters with an annual simulation model of the European Reference Room. The total setpoint variations were simulated for a set of heat emitters and controllers in order to quantify and compare the energy performance of a new and an old type building located in Strasbourg. We find that the total setpoint variation required to overcome emission losses is up to 2.00 °C in the old building and 1.20 °C in the new building, corresponding respectively to an increase in total heating energy usage of up to 22% and 20%.

In recent decades, widespread damage to structures due to destructive earthquakes has encouraged researchers to use seismic control systems. One of the most important structures is bridges, which should maintain their service after severe earthquakes. One of the ways to control the bridge is to isolation the deck from the substructure, which results in high displacements at different points in the bridge and the residual displacements within the separator itself, thus requiring repair and replacement of these systems after severe earthquakes. Therefore, the use of new seismic separation systems on bridges has always been important. The purpose of this project is to utilize a new memory-shaped seismic separator system to investigate the seismic performance of v-shaped column bridges , in which case the effect of earthquake orientation and its effects on responses the earthquake will also be assessed. Due to the ever-increasing advances in various intelligent materials, such as shape memory alloys, and their unique capacities, such as back-centering, and high fatigue and corrosion resistance, in this study, these materials have been used as a complementary component along with lead core separators. The shape memory alloy has been used as 4 vertical rods that connect two separating parts to each other and in this research the diameter and location of these rods will be calculated using optimization algorithm in Matlab software.

In the present trend of constructing taller and longer structures, the application of lightweight aggregate concrete is becoming an increasing important advanced solution in the modern construction industry. In engineering practice, the analysis of lightweight concrete elements is performed using the same algorithms used for normal concrete elements. As an alternative to traditional engineering methods, nonlinear numerical algorithms based on constitutive material models may be used. The paper presents a comparative analysis of curvature calculations for flexural lightweight concrete elements, incorporating analytical code methods EN 1992-1 and ACI 318-14, as well as a numerical analysis using the constitutive model of cracked tensile lightweight concrete recently proposed by the authors. To evaluate the adequacy of the theoretical predictions, experimental data of 51 lightweight concrete beams tested during five different programmes were collected. A comparison of theoretical and experimental results showed that the most accurate predictions are obtained using numerical analysis and the constitutive model proposed by the authors. In the future, the latter algorithm can be used as a reliable tool for improving the design standard methods or numerical modelling of lightweight concrete elements subjected to short-term loading.

Dams design and their operation cause strong environmental alteration and therefore a long-term debate is ongoing for the scale of these projects. At the same time, the concept of Environmental Flow Assessment (EFA) is a crucial element of modified ecosystems featuring large infrastructure such as dams and reservoirs for mitigating potential environmental degradation while they operate. Nowadays, integrated scientific frameworks are required to quantify the risks caused by large infrastructure. Through the use of stochastic analysis, it is possible to quantify these uncertainties, and present a solution that incorporates long-term persistence and environmental sustainability into a balanced reservoir simulation model. In this work, an attempt is made to determine a benchmark reservoir size incorporating hydrological and ecological criteria though stochastic analysis. The primary goal is to ensure the best possible conditions for the ecosystem, and then secondarily to allow a steady supply of water for other uses. Using a synthetic timeseries based on historical inputs, it is possible to determine and preserve essential statistical characteristics of a river’s streamflow, and use these to detect the optimal reservoir capacity that maximizes environmental and local water demand reliability.

Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost variances using proprietary C-S and S-C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

Research shows that in earthquakes the ground response changes in areas where there are underground cavities. Due to the fact that subways and underground tunnels pass from beneath buildings in urban areas, these changes in ground response have a direct impact on the seismic behavior of structures. In this study, first by model validity and reliability of the results, steel structures modeling was conducted and steel structure behavior was evaluated due to Tunnel-Soil-Structure seismic interaction. Parameters studied are number of stories, soil type, tunnel depth, horizontal tunnel-structural distance and dynamic loading. Considering that one of the most important parameters of structural control is drift and story displacement, so this important factor will be considered. The results show that tunneling has a direct effect on the rate of structural displacement and increases the structural response. Also, the behavior of the structure is affected by the position of the structure at the ground level and the position of the tunnel and this should be considered during the design phase of the structures.

Information and communication technologies play an increasingly important role in the process of knowledge and management of places at different scales. ICTs allow a rapid diffusion of data not only through institutional channels but also through social networks where the smart community share experiences and perceptions. In this sense, ICTs become strategic tools to support the promotion of sustainable tourism development of territories, especially if the digital data are organised within a circular smart dashboard. This research focuses on the case study of the Santa Barbara Walk (SBW), an ancient mining route in the Sulcis Iglesiente region (Sardinia, Italy), where the authors have recognized a state of disorganization in slow tourism promotion activities. In fact, if the SBW represents a network - material infrastructure - which connects the main points of interest along the Walk, its digital network - intangible infrastructure - is fragmented in terms of policies and contents. The goal of this study is to provide a comprehensive set of data and to propose the architecture and design for a circular dashboard of the SBW, capable of organizing information concerning the main features of the walk, in order to facilitate a shared governance for an effective tourism promotion.

Phase Change Materials (PCMs) are latent heat storage media with high potential of integration in building structures and technical systems. Their solid-liquid transition is commonly utilized for thermal energy storage in building applications. It also means that some kind of encapsulation is necessary. This is often solved with metal containers that also have high thermal conductivity and resistance to mechanical damage enhancing the performance these so called latent heat thermal energy storage (LHTES) systems. However selection of suitable metal is rather challenging. It depends, among other things, on the elimination of undesirable interaction between storage medium and surrounding metal. Heat storage medium must be reliably sealed in metal container especially when the storage system is integrated in systems like domestic hot water storage tanks, where PCM leaks can negatively affect human health. The aim of this study was evaluation of interaction between selected commercially available organic and inorganic PCMs and metals. The evaluation is based on the calculation of corrosion rate and use gravimetric method for determination of the weigh variations of the metal samples. Results show that aluminium is the most suitable container material with lowest mass loss and suffered only minimal visual changes on the surface after prolonged exposure to PCMs.

The objective of this work was to evaluate the removal of phosphorus and carbon dioxide capture of a conventional septic system upgraded with a sidestream steel slag filter used in recirculation mode. A pilot scale sidestream experiment was conducted with two septic tank and drainfield systems, one with and one without a sidestream slag filter. The experimental system was fed with real domestic wastewater. Recirculation ratios of 25%, 50% and 75% were tested. Limestone soils and silica soils were used as drainfield media. The phosphorus removal efficiency observed in the second compartment of the septic tank was 30% in the slag filter upgraded system, compared to -3% in the control system. The drainfield of silica soils achieved very high phosphorus removal in both control and upgraded systems. In the drainfield of limestone soil, the slag filtration reduced the groundwater phosphorus contamination load by up to 75%. Phosphorus removal in the septic tank with a slag filter was attributed to either sorption on newly precipitated calcium carbonate or precipitation of vivianite, or both. Recirculation ratio design criteria were proposed based on simulations. Simulations showed that the steel slag filter partly inhibited biological production of carbon dioxide in the septic tank. The influent alkalinity strongly influenced the recirculation ratio needed to raise the pH in the septic tank. The control septic tank produced carbon dioxide, whereas the slag filter upgraded septic tank was a carbon dioxide sink.

In this study, to reduce the use of cement and sand, porous feldspar with excellent economic efficiency was used as a substitute in heat storage concrete layer. When cement was replaced with porous feldspar, the compressive strength was approximately 16%–63% higher compared with when cement was replaced with silicate minerals. To compensate for the reduction in strength owing to the decreased cement content, mechanical and chemical activation methods were employed. When the specific surface area of porous feldspar was increased, the unit weight was reduced by approximately 30% and the compressive strength was increased by up to 90%. When chemical activation was applied using a solidifying agent, the strength was increased by approximately 30% even though 70% of the cement content was replaced with porous feldspar. When cement and sand were replaced with porous feldspar, the compressive strength was approximately two times that of ordinary cement mortar. When the heat storage concrete layer material was replaced with porous feldspar in a pilot scale experiment, the thermal conductivity and heat storage characteristics were better than those of ordinary cement mortar, and an energy-saving effect of approximately 57% was observed, confirming the excellent applicability of porous feldspar as a building material.