Self-assembling films typically used for colloidal lithography have been applied to pine wood substrates to change the surface wettability. Therefore, monodisperse polystyrene (PS) spheres have been deposited onto a rough pine wood substrate via dip coating. The resulting PS sphere film resembled a polycrystalline FCC-like structure with typical domain sizes of 5 – 15 single spheres. This self-assembled coating was further functionalized via an O2 plasma. This plasma treatment strongly influenced the particle sizes in the outermost layer, and hydroxyl as well as carbonyl groups were introduced to the PS spheres’ surfaces, thus generating a superhydrophilic behaviour.

In order to improve the performance of soft plantation wood, an environmentally friendly inorganic-organic hybrid wood modifier was developed. First, using urea and melamine as crosslinking agents, the waterborne glucose silicone resin (MUG) was prepared with glucose under the catalysis of inorganic acid and metal ions. Then MUG resin was diluted to 10% and 20% mass fraction, and compounded with sodium silicate (S) of 20% and 10% mass fraction, so the inorganic-organic hybrid G10S20 and G20S10 wood modifier were obtained respectively. Then plantation poplar wood (Populus tomentosa) were impregnated and modified with them. Their physical and mechanical properties were tested and compared with those of the wood treated with S of 20% mass fraction (S20). Infrared analysis showed that amino resin characteristic structure (CO-NH-) existed in MUG resin. The resin has good permeability. Compared with S20 modified wood, the degree of shrinkage of G10S20 or G20S10 modified wood is reduced, their moisture absorption is reduced, and their dimensional stability is improved. Waterborne glucose silicone modifier can effectively improve the wood density, modulus of elasticity, modulus of rapture and compression strength. SEM analysis showed that the cell wall of G20S10 modified wood was significantly thicker than the untreated wood, and there were columnar and granular solid substances attached in some cell cavities, ducts and corners, etc. EDX showed that the number of Si elements on the cell wall was significantly increased compared with the control, indicating that the modifier effectively entered the wood cell wall. The waterborne glucose silicone resin can greatly improve the physical and mechanical properties of wood through organic-inorganic hybridization. It is a green, non-formaldehyde, eco-friendly, low cost, compound wood modifier with broad application prospects.

Accurate expression of bracket prescription is important for successful orthodontic treatment. The aim of this study was to evaluate the accuracy of digital scan images of brackets produced by four different intraoral scanners (IOSs) in terms of the height, position, and angle of the bracket slot when scanning the surface of dental model attached with bracket materials made from different composition of materials. Brackets made from stainless steel, polycrystalline alumina, composite and composite/stainless steel slot were considered, which have been scanned from 4 different IOSs (Primescan, Trios, CS3600 and i500). SEM images were used as references. Each bracket axis was set in the reference scan image, and the axis was set identically by superimposing with the IOS image, and then only the brackets were divided and analyzed. The difference between the manufacturer's nominal torque and bracket slot base angle was 0.39 in SEM, 1.96 in Primescan, 2.04 in Trios, and 5.21 in CS3600 (P <0.001). The parallelism, which is the difference between the upper and lower angles of the slot wall, was 0.55 in SEM, 7.55 in Primescan, 6.74 in Trios3, 6.59 in CS3600, and 24.95 in i500 (p <0.001). This study evaluated the accuracy of the bracket only and it must be admitted that there is some error in recognizing slots through scanning in general

In this work, effects of 20 transition element additives on the interfacial adhesion energy and electronic structure of Al (111)/6H-SiC (0001) interfaces have been studied by first principles method. For clean Al (111)/6H–SiC (0001) interfaces, both Si-terminated and C-terminated interfaces have covalent bond characteristics. The C-terminated interface has stronger binding energy, which is mainly due to the stronger covalent bond formed by the larger charge transfer between C and Al. The results show that the introduction of many transition elements, such as 3d transitional group Mn, Fe, Co, Ni, Cu, Zn and 4d transitional group Tc, Ru, Rh, Pd, Ag, can improve the interfacial adhesion energy of the Si-terminated Al (111)/6H-SiC (0001) interface. However, for the C-terminated Al (111)/6H-SiC (0001) interface, only the addition of Co element can improve the interfacial adhesion energy. Bader charge analysis shows that the increase of interfacial binding energy is mainly attributed to more charge transfer.

Scaffolds are widely used in tissue engineering because their manufacture is based on natural and synthetic polymers, which allows them to have properties such as biocompatibility and biodegradability, creating an ideal environment for cell growth on their surface. In this context, among the polymers studied in Tissue Engineering are Chitosan (CH) and Polyvinyl Alcohol (PVA). CH is a versatile polymer obtained from de-acetylation of chitin, which is used for its high biodegradability and biocompatibility, although its mechanical properties must be improved. It has been found that one of the ways to improve the mechanical properties of CH is to mix it with other synthetic polymers such as PVA. PVA is known for its biocompatibility, biodegradability, zero toxicity and ease of preparation due to its solubility in water and excellent mechanical properties, such as tensile strength and ease in the formation of films and barriers. In this study we evaluated the capacity of scaffolds made with CH and PVA in different concentrations (2: 1, 1: 1, 1: 2, respectively) as a possible application in bone regeneration. This was made through different characterization tests such as Infrared Spectroscopy, AFM, Swelling test and Porosity test, where we obtained information about its structural and physicochemical properties. Additionally, a cellular quality control was performed on the material through the MTT assay. The Fourier transform infrared spectroscopy (FTIR) study showed that there are strong intermolecular hydrogen bonds between the chitosan and polyvinyl alcohol molecules. The Swelling and Porosity tests showed favorable results, obtaining maximum values ​​of 5519% and 72.17% respectively. MTT tests determined that the prepared materials are not cytotoxic. These findings suggest that scaffolds possess properties suitable for use in Tissue Engineering.

To combat infections on biomedical devices, antimicrobial coatings have attracted considerable attention, including coatings comprising naturally occurring antimicrobial peptides (AMPs). In this study the aim was to explore performance upon extended challenge by bacteria growing in media above samples. The AMPs LL37, Magainin 2, and Parasin 1 were covalently grafted onto a plasma polymer platform, which enables application of this multilayer coating strategy to a wide range of biomaterials. Detailed surface analyses were performed to verify the intended outcomes of the coating sequence. Samples were challenged by incubation in bacterial growth media for 5 and 20 hrs. Compared with the control plasma polymer surface, all three grafted AMP coatings showed considerable reductions in bacterial colonization even at the high bacterial challenge of initial seeding at 1x107 CFU, but there were increasing numbers of dead bacteria attached to the surface. All three grafted AMP coatings were found to be non-toxic to primary fibroblasts. These coatings thus could be useful to produce antibacterial surface coatings for biomaterials, though possible consequences arising from the presence of dead bacteria need to be studied further, and compared to non-fouling coatings that avoid attached dead bacteria.

Melt mixing is a convenient method to prepare polymer nanocomposites, but the extent of the dispersion of the solid filler reached is often limited, and may compromise the anticipated performance of these materials during service. Since the efficiency of extensional flows on dispersion is now well recognized, several mixers were designed with the aim of inducing both shear and extensional flow components. This work combines experimental and numerical data to better understand the kinetics of the dispersion of graphite nanoplates in a polypropylene melt, using a mixing device that consists of a series of stacked rings with equal outer diameter and alternating larger and smaller inner diameters, thus creating a series of converging/diverging flows. Numerical simulation of the flow using the opensource OpenFOAM software assuming both inelastic and viscoelastic responses predicted the velocity, streamlines, flow type and shear and normal stress fields for the mixer. Experimental and computed data were combined to determine the trade-off between the local degree of dispersion of the PP/GnP nanocomposite, measured as Area ratio, and the absolute average value of the hydrodynamic stresses multiplied by the local cumulative residence time. From considerations based on a theoretical approach to dispersion, the cohesive strength of the GnP agglomerates studied was estimated to be in the range 3 - 10kPa.

Diamond is a material with excellent performances which attracts the attention from researchers for decades. Pt (111), owing to its catalytic activity on diamond synthesis, is regarded to be a candidate for diamond hetero-epitaxity, which can enhance nucleation density. Molten surface at diamond growth temperature can also improve mobility and aggregation capability of primitive nuclei. Generally, (100)-oriented is welcomed for the achivement of high quality and large size diamond, since the formation of defects and twins are prevented. First-principle calculations and experimental researches were carried out for the study of transformation of orientation. The transformation from {111} to {100}-oriented diamond has been observed on Pt (111) substrate, which can be promoted by the increase of carbon source concentration and substrate temperature. The process is energetic favorable, which may provides a way towards large-scale (100) diamond films.

The folding of certain proteins (e.g., enzymes) into perfectly defined 3D conformations via multi-orthogonal interactions is critical to their function. Concerning synthetic polymers chains, the “folding” of individual polymer chains at high dilution via intra-chain interactions leads to so-called single-chain nanoparticles (SCNPs). This review article describes the advances carried out in recent years in the folding of single polymer chains into discrete SCNPs via multi-orthogonal interactions using different reactive chemical species where intra-chain bonding only occurs between groups of the same species. First, we summarize results from computer simulations of multi-orthogonally folded SCNPs. Next, we comprehensively review multi-orthogonally folded SCNPs synthesized via either non-covalent bonds or covalent interactions. Finally, we conclude by summarizing recent research about multi-orthogonally folded SCNPs prepared through both reversible (dynamic) and permanent bonds.

Abstract: This study was aimed to determine the influence of the volume fraction of steel fibers and on fracture parameters of concrete. Fifty notched steel fiber reinforced concrete (SFRC) beams and ordinary concrete beams with dimensions of 100mm×100mm×515mm were cast and tested via three-point bending test. Among them, the type of steel fiber is milling type (MF), and the volume fraction of steel fiber added is 0%, 0.5%, 0.5%, 1.5%, 1.5%, 2%, respectively. The effects of the steel fiber volume fraction (VF) on the critical stress intensity factor (KIC), fracture energy (GF), the deflection at failure(δ0), the critical crack mouth opening displacement (CMODC) and the critical crack tip opening displacement (CTODC)were studied. Through the analysis of test phenomena and test data such as load-deflection (P-δ) curve, load-crack mouth opening displacement (P-CMOD) curve and load-crack tip opening displacement (P-CTOD) curve following conclusions are drawn: With the increase of steel fiber volume fraction, some fracture parameters increase gradually and maintain a certain linear growth. The gain ratio of fracture parameters increases significantly, and the gain effect is obvious. Through this law of growth, the experimental statistical formulas of fracture energy and critical stress intensity factor are summarized.

In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP:PMMA or BCP:PVP/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

Space vehicles may be propelled by solar sails exploiting the radiation pressure coming from the sun and applied on their surfaces. This work deals with the adoption of Shape-Memory Alloy (SMA) elements in the sail deployment mechanism activated by the Joule Effect, i.e. using the same SMA elements as a resistance within suitable designed electrical circuits. Mathematical models were analyzed for the thermal analysis by implementing algorithms for the evaluation of the temperature trend depending on the design parameters. Several solar sail prototypes were built up and tested with different number, size and arrangement of the SMA elements, as well as the type of the selected electrical circuit. The main parameters have been discussed in the tested configurations and advantages discussed as well.

BioPBS is gaining attention in the biodegradable polymer market due to their promising properties such as high biodegradability and processing versatility representing a potential sustainable replacement for fossil oil-based commodities. However, there is still a need to enhance its properties for certain applications, being aesthetical and mechanical properties a challenge. The aim of the present work is to improve these properties by adding selected additives that will confer bioPBS with comparable properties to that of current counterparts such as polypropylene (PP) for specific applications in the automotive and household appliances sectors. A total of thirteen materials have been studied and compared, being twelve biocomposites containing combinations of three different additives: a commercial red colourant, itaconic acid (IA) to enhance colour fixation and zirconia (ZrO2) nanoparticles to maintain at least native PBS mechanical properties. Results show that the combination of IA and the colouring agent tends to slightly yellowish the blend due to the absorbance spectra of IA and also to modify the gloss due to the formation of IA nanocrystals that affects light scattering. In addition, for low amounts of IA (4wt.%), young modulus seems to be kept while elongation at break is even raised. Unexpectedly, a strong aging affect was found after 4 weeks. IA increases the hydrophilic behaviour of the samples and thus seems to accelerate the hydrolisation of the matrix, which is accompanied by an accused disaggregation of phases and an overall softening and rigidization effect. The addition of low amounts of ZrO2 (2wt.%) seems to provide the desired effect for hardening the surface while almost not affecting the other properties; however, higher amounts tends to form aggregates saturating the compounds. As a conclusion, IA might be a good candidate for colour fixing in biobased polymers.

In order to obtain stable super-hydrophobicity, suitable hydrophobic treatment agent should be selected according to different materials. In this paper, cotton and poly (-ethylene terephthalate) (PET) fabric was respectively coated by dodecyl methacrylate (LMA) via argon combined capacitively coupled plasma (CCP), and the surface hydrophobicity and durability of treated cotton and polyester fabrics were also discussed. An interesting phenomenon was happened that LMA coated cotton fabric (Cotton-g-LMA) had better water repellency and mechanical durability than LMA coated PET fabric (PET-g-LMA), and LMA coated hydroxyl grafted PET fabrics (PET fabrics were successively coated with polyethylene glycol (PEG) and LMA, PET-g-PEG&amp;LMA) had similar performance to those of cotton fabrics. The water contact angle (WCA) of Cotton-g-LMA, PET-g-LMA and PET-g-PEG&amp;LMA was 156 °, 153 ° and 155 °, respectively, and after 45 washing cycles or 1000 rubbing cycles, the corresponding WCA was decreased to 145 °, 88 °, 134 °and 146 °, 127 °, 143 °, respectively. Also, thermoplastic polyurethane (TPU) and polyamides-6 (PA6) fabrics were all exhibited the same properties to PET fabric. Therefore, the grafting of hydroxyl can improve the hydrophobic effect of LMA coating and the binding property between LMA and fabrics effectively without changing the wearing comfort..

In the last 10 years, carbon dots (CDs) synthesized from renewable organic resources have been gathered a considerable amount of attention in different fields for their peculiar photoluminescent properties. Moreover, the synthesis of CDs fully responds to the principles of the circular chemistry and the concept of safe-by-design. This review will focus on the different strategies for the incorporation of CDs in organic light-emitting devices (OLEDs) and on the study of the impact of CDs properties on the OLEDs performance. The main current research outcomes and highlights are summarized to guide users towards the fully exploitation of use these materials in optoelectronic applications.

The effect of the strain rate on damage in carbon black filled EPDM stretched during single and multiple uniaxial loading is investigated. This has been performed by analysing the stress-strain response, the evolution of damage by Digital Image Correlation (DIC), the associated dissipative heat source by InfraRed thermography (IR), and the chains network damage by swelling. The strain rates were selected to cover the transition from quasi-static to medium strain rate conditions. In single loading conditions, the increase of the strain rate yields in a preferential damage of the filler network while rubber network is preserved. Such damage is accompanied by a stress softening and an adiabatic heat source rise. Conversely, increasing the strain rate in cyclic loading conditions yields in a filler network accommodation and a high self-heating whose combined effect is proposed as a possible cause of the ability of filled EPDM to limit damage, by reducing cavities opening during loading and favoring cavities closing upon unloading.

Non-alcoholic fatty liver (NAFLD) is a metabolic disorder related with a chronic lipid accumulation within the hepatocytes. This disease is the most common liver disorder worldwide and it is estimated that is present in up to 25% of the world's population. However, the real prevalence of this disease and the associated disorders is unknown mainly because reliable and applicable diagnostic tools are lacking. It is known that the level of albumin, a pleiotropic protein synthetized by hepatocytes, is correlated with the correct function of the liver. The development of a complementary tool that allow the direct, sensitive, and label-free monitoring of albumin secretion in hepatocyte cell culture can provide insight about the mechanism and drugs action in NAFLD. With this aim, we have developed a simple integrated plasmonic biosensor based on gold nanogratings from periodic nanostructures present in commercial Blu-ray optical disc. This sensor allows the direct and label-free monitoring of albumin in a 2D fatty liver disease model under flow conditions using highly specific polyclonal antibody. This technology avoids both the amplification and blocking steps showing a limit of detection within pM range (≈ 0.39 ng/mL). Thanks to this technology, we identified the optimal fetal bovine serum (FBS) concentration to maximize the lipid accumulation within the cells. Moreover, we discovered that at third day from lipids challenge, the hepatocytes increased the amount of albumin secreted. These data demonstrate the ability of hepatocytes to respond to the lipid stimulation releasing more albumin. Further investigation needed to unveil the biological significance of that cell behaviour.

Three-dimensional porous nanostructures made of noble metals represent novel class of nanomaterials promising for nonlinear nanooptics and sensors. Such nanostructures are typically fabricated using either reproducible yet time-consuming and costly multi-step lithography protocols or less reproducible chemical synthesis that involve liquid processing with toxic compounds. Here, we combined scalable nanosecond-laser ablation with advanced engineering of the chemical composition of thin substrate-supported Au films to produce nanobumps containing multiple nanopores inside. Most of the nanopores hidden beneath the nanobump surface can be further uncapped using gentle etching of the nanobumps by an Ar-ion beam to form functional 3D plasmonic nanosponges. The nanopores 10-150~nm in diameter were found to appear via laser-induced explosive evaporation/boiling and coalescence of the randomly arranged nucleation sites formed by nitrogen-rich areas of the Au films. Density of the nanopores can be controlled by the amount of the nitrogen in the Au films regulated in the process of their magnetron sputtering assisted with nitrogen-containing discharge gas.

In the article we present the results concerning the impact of structural and chemical properties of zinc oxide in various morphological forms, on its gas-sensitive properties tested in an atmosphere containing a very aggressive gas such as chlorine. Two types of ZnO sensor layers obtained by two different technological methods were used. Their morphology, crystal structure, specific surface area, porosity, surface chemistry and structural defects were characterized, and then compared with gas-sensitive properties in a chlorine-containing atmosphere. To achieve this goal scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL) methods were used. The sensing properties of obtained active layers were tested by temperature stimulated conductance method (TSC). We have noticed that their response in chlorine atmosphere is not determined by the size of the specific surface or porosity. The obtained results showed that the structural defects of ZnO crystals play the most important role in chlorine detection. We demonstrated that the Cl2 adsorption is a concurrent process to oxygen adsorption. Both of them occur on the same active species (oxygen vacancies). They concentration is higher on the side planes of the zinc oxide crystal than the others. Thanks to the conducted studies authors demonstrated that to develop a new gas sensor devices not only changing of active layer chemical composition but also controlling its crystal structure and morphology could be used.

Within the study, magnetic/polyetherimide-acrylonitrile composite nanofibers membrane with effective adsorption of nickel ions in aqueous solution were established, through a simple electrospinning method. Iron oxide nanoparticles were stirred and ultrasonically dispersed into polyetherimide-acrylonitrile solution for homogenous suspension. Afterwards, the polyetherimide-acrylonitrile solution with uniform suspension of iron nanoparticles was used in electrospinning machine to produce uniform and smooth nanofibers composite membrane. The confirmation of nanoparticles incorporation into polymeric membrane were characterized by SEM, EDX, FTIR, XRD and nanoparticles aqueous stability through leach out test. The high adsorption capability of the composite membranes on nickel ions was mainly attributed to the combination of magnetic nanoparticles, polyetherimide-acrylonitrile matrix and nano-sized structure of membrane. Membrane containing magnetic nanoparticles demonstrate the maximum adsorption capabilities (102 mg/g) for nickel ions from aqueous solution. Different kinetics and isotherm models were applied to understand the adsorption behavior during adsorption process, amongst them pseudo second order kinetic and Langmuir isotherm model were well fitted. Additionally, EDX, FTIR and XRD results confirmed the presence of nickel ions onto membrane after adsorption process. Polyetherimide-acrylonitrile composite nanofibers membranes containing magnetic nanoparticles may use as an environmentally-friendly and non-toxic adsorbent for the removal of nickel ions in aqueous medium due to its ease of preparation, easy to use and stability in aqueous medium by retaining the nanoparticles inside the nanofibers membranes.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

By introducing a suitable renormalization process the charge carrier and phonon dynamics of a double-stranded helical DNA molecule is expressed in terms of an effective Hamitonian describing a linear chain, where the renormalized transfer integrals explicitly depend on the relative orientations of the Watson-Crick base pairs, and the renormalized on-site energies are related to the electronic parameters of consecutive base pairs along the helix axis, as well as to the low-frequency phonons dispersion relation. The existence of synchronized collective oscillations enhancing the π-π orbital overlapping among different base pairs is disclosed from the study of the obtained analytical dynamical equations. The role of these phonon-correlated, long-range oscillation effects on the charge transfer properties of double standed DNA homopolymers is discussed in terms of the resulting band structure.

Herein, we report results of the study of the composite ferroelectric scaffolds based on vinylidene fluoride-tetrafluoroethylene copolymer (VDF-TeFE) and polyvinylpyrrolidone (PVP) produced by electrospinning and their application as a wound-healing material. The physicochemical properties of ferroelectric composite polymer scaffolds depending on the content of PVP (in the range from 0 to 50 wt %) including morphology, composition and crystalline structure were studied. The cytotoxicity of materials and the proliferative activity of cells during their cultivation on the surface of formed scaffolds are reported. It has been found that the optimal PVP content in the VDF-TeFE composite scaffolds is 15 wt%. On a model of a full-thickness contaminated wound in vivo, it was shown that piezoelectric scaffolds based on VDF-TeFE copolymer containing 15 wt% PVP provide better wound healing results in comparison with standard gauze dressings impregnated with a solution of an antibacterial agent.

The utilisation of the industrial residual products to create new value-added materials and to reduce footprint is a modern challenge of science and industry. Development of the new multifunctional and bio-based composites is an excellent opportunity for complex utilisation of industrial residual products. The study describes the preparation and characterisation of the three-phases bio-based composites. The main components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash the cenosphere (CS). Three-phase composite prepared in the form of a block for investigation of the mechanical properties and density and a form of granules for determination of the water and oil products sorption was investigated. This work investigated the dependence of the properties on the main component DCR and CS fraction. Is found, that maximum compression strength (in block form) observed for composition without CS and DCR addition - 79.3 MPa, the second highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt% compression strength is in range 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.

Bioactive glass (BG) represents a promising biomaterial for bone healing; here injectable BG pastes biological properties were improved by 25 wt% gelatin or chitosan, as well as mechanical resistance was enhanced by adding 10 or 20 wt% 3-Glycidyloxypropyl trimethoxysilane (GPTMS) cross-linker. Composites exhibited bioactivity as apatite formation was observed by SEM and XRD after 14 days immersion in SBF; moreover, polymers did not enhance degradability as weight loss was &gt;10% after 30 days in physiological conditions. BG-gelatin-20 wt% GPTMS composites demonstrated the highest compressive strength (4.8±0.5 MPa) in comparison with 100% BG control (1.9±0.1 MPa). Cytocompatibility was demonstrated towards human mesenchymal stem cells (hMSC), osteoblasts progenitors and endothelial cells. The presence of 20 wt% GPTMS conferred antibacterial properties thus inhibiting the joint pathogens Staphylococcus aureus and Staphylococcus epidermidis infection. Finally, hMSC osteogenesis was successfully supported in a 3D model as demonstrated by alkaline phosphatase release and osteogenic genes expression.

Cranio-maxillofacial structure is a region of particular interest in the field of regenerative medicine due to both its anatomical complexity and the numerous abnormalities affecting this area. However, this anatomical complexity is what makes possible the coexistence of different microbial ecosystems in the oral cavity and the maxillofacial region, contributing to the increased risk of bacterial infections. In this regard, different materials have been used for their application in this field. These materials can be obtained from natural and renewable feedstocks or by synthetic routes with desired mechanical properties, biocompatibility and antimicrobial activity. Hence, in this review, we have focused on bio-based polymers, which by their own nature, by chemical modifications of their structure, or by their combination with other elements, provide a useful antibacterial activity as well as the suitable conditions for cranio-maxillofacial tissue regeneration. This approach has not been reviewed previously, and we have specifically arranged the content of this article according to the resulting material and its corresponding application, reviewing guided bone regeneration membranes; bone cements; and devices and scaffolds for both soft and hard maxillofacial tissue regeneration, including hybrid scaffolds, dental implants, hydrogels and composites.

With the increased scientific interest in green technologies, many researches have been focused on the production of polymeric composites containing naturally occurring reinforcing particles. Apart from increasing mechanical properties, these additions can have a wide range of interesting effects, such as increasing the resistance to bacterial and fungal colonization. In this work, different amounts of two different natural products, namely neem and turmeric, have been added to polyethylene to act as a natural antibacterial and antifungal product for food packaging applications. Microscopic and spectroscopic characterization showed that fractions up to 5% of these products can be dispersed into low-molecular weight polyethylene, while higher amounts could not be properly dispersed and resulted in an inhomogeneous, fragile composite. In vitro testing conducted with Escherichia coli, Staphylococcus aureus and Candida albicans showed a reduced proliferation of pathogens when compared to the polyethylene references. In particular, turmeric, resulted to be more effective against E. coli when compared to neem, while they had similar performances against S. aureus. Against C. albicans, only neem was able to show a good antifungal behavior, at high concentrations. Tensile testing showed that the addition of reinforcing particles reduces the mechanical properties of polyethylene, and, in the case of turmeric, it is further reduced by UV irradiation.

(1) Background: The evaluation of ventricular assist devices requires the usage of biocompatible and chemically stable materials. The commonly used polyurethanes are characterized by versatile properties making them well suited for heart prostheses applications but simultaneously they show low stability in biological environment. (2) Methods: An innovative material - copolymer of poly(ethylene-terephthalate) and dimer linoleic acid - with controlled and reproducible physico-mechanical and biological properties was developed for medical applications. Biocompatibility (cytotoxicity, surface thrombogenicity, hemolysis and biodegradation) were evaluated. All results were compared to medical grade polyurethane currently used in the extracorporeal heart prostheses. (3) Results: No cytotoxicity was observed and no significant decrease of cells density as well as no cells growth reduction was noticed. Thrombogenicity analysis showed that the investigated copolymers have the thrombogenicity potential similar to medical grade polyurethane. No hemolysis was observed (the hemolytic index was under 2% according to ASTM 756-00 standard). These new materials revealed excellent chemical stability in simulated body fluid during 180 days ageing. (4) Conclusions: The biodegradation analysis showed no changes in chemical structure, molecular weight distribution, good thermal stability and no changes in surface morphology. Investigated copolymers revealed excellent biocompatibility and great potential as materials for blood contacting devices.

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

Modified ammonium polyphosphate (MAPP) as a novel mono-component intumescent flame retardant (IFR) was prepared via the ionic exchange between ammonium polyphosphate (APP) and piperazine sulfonate, which is synthesized by self-assembly using 1-(2-Amioethyl) piperazine (AEP) and p-amino benzene sulfonic acid (ASC) as raw materials. This all-in-one IFR integrating three functional elements (carbon, acid, and gas source) showed more efficient flame retardancy and excellent smoke suppression as well as better mechanical properties than the conventional APP. The incorporation of 22.5 wt.% MAPP into polypropylene (PP) eliminated the melt dripping phenomenon and passed the UL-94 V-0 rating. The results of the cone calorimetry test (CCT) revealed that the release of heat, smoke, and CO is significantly decreased, demonstrating that this novel IFR endows PP with excellent fire safety more effectively. For PP/MAPP composites, a possible IFR mechanism was proposed based on the analysis of the pyrolysis gas and char residues.

In this paper, various Ni-P composite coatings containing toner, MoS2, and nano-SiO2 particles were deposited on steel substrates by the electroless method. Then, the electrochemical properties of these coatings after a heat treatment process were compared. The microstructural evaluations were also done by using the optical and electron microscopy methods. Both Tafel polarization and electrochemical impedance spectroscopy techniques were utilized to survey the electrochemical behavior of such coatings. The surface morphology of all coatings contained cauliflower-like nodules. The X-ray diffraction patterns showed the crystalline phases of Ni and Ni3P for all coatings after the heat-treatment step. Obtained results showed that all composite coatings exhibited lower corrosion rates with respect to Ni-P coatings. Such a reduction was about 21.6-92.2%. This behavior was attributed to the presence of reinforcement as barriers for corrosive ion diffusion through the coating plus the changes in detected phases and thickness. Electrochemical impedance spectroscopy test results also demonstrated that the increase in the polarization resistance for composites coatings was about 18.4-85.3% after 1 h immersion in a 0.6M NaCl solution; however, when the immersion time increased to 24 h, such increased resistance changed to 18.1 to 73.1%. Totally, despite the lower deposition rate, the presence of MoS2 and nano-SiO2 particles were more effective than toner particles to raise the corrosion rate of the Ni-P coating.

Deformation behavior of MXene based polymer composites with bioinspired brick and mortar structures is analyzed. MXene/Polymer nanocomposites are modeled at microscale using bioinspired configurations of nacre-mimetic brick-and-mortar assembly structure. MXenes (brick) with polymer matrix (mortar) are modeled using classical analytical methods and numerical methods based on Finite Elements (FE). The analytical methods provide less accurate estimation of elastic properties compared to numerical one. MXene nanocomposite models analyzed with FE method provide estimates of elastic constants in the same order of magnitude as literature reported experimental results with good consistency. Bioinspired design of MXene nanocomposites results in the effective Young’s modulus of the nanocomposite increase by 25.1 % and the strength (maximum stress capacity within elastic limits) increase by 42.3 %. The brick and mortar structure of the nanocomposites leads to interlocking mechanism between MXene fillers in polymer matrix, resulting in effective load transfer, good strength, and damage resistance. This is demonstrated in this paper by numerical analysis of MXene nanocomposites subjected to quasi-static loads.

Concern over potential antimony mediated toxicity from mining and smelting activities has instigated novel concepts toward removing aqueous antimony ions. The iron based adsorbent Fe3O4/HCO was found to be efficient for treating antimony-containing wastewater However, ineffective methodology for preparation limited its effective adsorption capacity and thus wider application. In this study, a new type of HCO-doped-(Fe3O4)x adsorbent was prepared by co-precipitation method for doping Fe3O4 into HCO sludge (HCO), thereby improving adsorption performance for Sb(III) and Sb(V) ions, with the maximum adsorbing capacity being 44.46 mg/g and 47.91 mg/g, respectively. According to the results of BET, SEM-EDS, XRD and XPS, it were confirmed that the FeOOH and X≡Fe-OH were formed during the preparation process, bring about the increased the surface area, thus resulting in further increase of surface area, hydroxyl groups and the net negative ionic charge. Moreover, the adsorption kinetics followed the pseudo-second-order kinetic model which indicated that adsorption process of Sb(III)/Sb(V) by HCO-doped-(Fe3O4)x adsorbent was controlled by chemical reaction. The main adsorption mechanism is that antimony ion and amorphous iron oxide X≡Fe-OH undergo coordination exchange reaction and complexation reaction with CeO2 or Ce2O3. Furthermore, HCO-doped-(Fe3O4)x could adapt to wide pH and had stable adsorption ability after regeneration. The good adsorption performance of HCO-doped-(Fe3O4)x makes it a potential applications of adsorbent for removal of antimony.

In this work, a deep characterization of the properties of K6Ta10.8O30 microrods has been performed. The starting material used to grow the microrods has been recovered from mining tailings coming from the Penouta Sn-Ta-Nb deposit, located in the north of Spain. The recovered material has been submitted to a thermal treatment to grow the microrods. Then, they have been characterized by scanning electron microscopy, X-ray diffraction, micro-Raman and micro-photoluminescence. The results of our study confirm that the K6Ta10.8O30 microrods have a tetragonal tungsten bronze-like crystal structure, which can be useful for ion-batteries and photocatalysis.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

Nowadays, the massive use of tires generates large stocks of waste material which is a serious environmental problem. The usual method used for processing wasted tires is mechanical crushing, in which fiber, steel, and rubber are separated. The aim of this research is the recycling of the obtained rubber, called also GTR (Ground Waste Tires). With this purpose, the paper analyses the mechanical properties of the composites produced by mixing GTR with several industrial polymers. These composites are characterized by the percentage of GTR in the composite and its particle size. These two variables along with seven industrial polymers define a set of composites from which the mechanical properties are analyzed and presented. From the results, it can be drawn that this proposal could be a way to enhance some polymer properties and to contribute in some way to reduce the environmental wasted tires problem.

In this study, we investigate the influence of control type and strain rate on the lifetime of specimens manufactured from 50CrMo4. This influence is described by a strain rate dependent method that uses cyclic stress strain curves to correct displacement controlled cyclic test results. The objective of this correction is to eliminate the stress related differences between displacement controlled cyclic test results and force controlled cyclic test results. The method is applied to the results of ultrasonic fatigue tests of six different combinations of heat treatment, specimen geometry (notch factor) and atmosphere. The corrected results show an improved agreement with test results obtained on conventional fatigue testing equipment with similar specimens: the standard deviation in combined data sets is significantly reduced (p=4.1%). We discuss the literature on intrinsic and extrinsic strain rate effects in carbon steels.

At present, the world is now passing a very far different time than normal situation due to the COVID-19 pandemic crisis. The global life-style and human civilization is currently progressing with down-stream that affecting almost every sectors necessary for human civilizations except the current environmental situation. To control the COVID-19 spreading, most of the countries are following lockdown process that reduces human mobility, thus reducing the CO2 emission to the environment. Though the COVID-19 pandemic is a blessing for the present environment, however, the post-COVID world will face a massive thrust of energy and only conventional energy resources may not be enough to mitigate the energy demands. Solar power generation technology mainly the photovoltaic (PV) systems and their advancement can be the leading possibilities to minimize the gap between the power demand and generation. It is now time to think how we can improve the PV power generation in future and the post-COVID world. In this encyclopaedia communication, we report on Nano-technological approach to improve the conversion efficiency of GaAs solar cells. We have designed and optimized several types of nano-structured assemblies that can be implemented to reduce the front surface incident light reflection losses thus can assist to improve the conversion efficiency of GaAs solar cells.

The current paper aims to study the impact properties of additively manufactured Maraging steel (1.2709) using laser powder bed fusion (PBF-L) processing. The specimens were manufactured using 3Dsystems ProX 300 equipment under constant specific power input, or Andrew Number. The interactions between the build strategy and parameters, such as Hatch spacing and Scan speed was, and the impact strength and fracture were investigated. The Impact energy anisotropy was also investigated parallel and perpendicular to the build direction. Instrumented impact testing was performed, and the fractography supported that the fusion zone geometry dictated the fracture behaviour. The influence from gaseous elements such as Nitrogen, Oxygen and Hydrogen was found insignificant at the levels found in the printed material.

There is an increasing clinical need to develop novel biomaterials that combine regenerative and biocidal properties. In this work, we present the preparation of silver /silica based glassy bioactive (ABG) compositions via a facile, fast (20h), and low temperature (80 °C) approach and their characterization. The fabrication process included the synthesis of the bioactive glass (BG) particles followed by the surface modification of the bioactive glass with silver nanoparticles. The microstructural features of ABG samples before and after exposure to simulated body fluid (SBF) as well as their ion release behavior during SBF test were evaluated using infrared spectrometry (FTIR), ultraviolet- visible (UV-Vis) spectroscopy, X-ray diffraction (XRD), electron microscopies (TEM and SEM) and optical emission spectroscopy (OES). The antibacterial properties of the experimental compositions were tested against Escherichia coli (E. coli). The results indicated that the prepared ABG materials possess antibacterial activity against E. coli, which is directly correlated with the glass surface modification.

Light trapping in single nanowires (NWs) are of vital importance for photovoltaic applications. However, circular NWs (CNWs) can limit its light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light trapping in single NWs with an elliptical cross-section (ENWs). We demonstrate that the ENWs exhibit significantly enhanced light trapping compared with the CNWs, which can be ascribed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the elliptical cross-section can simultaneously increase the light path length by increasing the vertical axis and reshape the LMR modes by decreasing the horizontal axis. We found that the light absorption can be engineered via tuning the horizontal and vertical axes, the photocurrent is significantly enhanced by 374.0% (150.3%, 74.1%) or 146.1% (61.0%, 35.3%) in comparison with that of the CNWs with the same diameter as the horizontal axis of 100 (200, 400) nm or the vertical axis of 1000 nm, respectively. This work advances our understanding of how to improve light trapping based on the symmetry breaking from the CNWs to ENWs and provides a rational way for designing high-efficiency single or self-assembled NW photovoltaic devices.

In this work, fluorinated graphene nanoscrolls (FGN) were synthesized via facile chemical methods under simple and mild conditions. Interestingly, the formation of the featured FGN was significantly solvent sensitive. Experimental results indicated that in the presence of aprotic solvent, for example, N,N dimethylformamide (DMF), the reaction system inclined to form the interesting FGN nanostructures. The structure and morphology of the prepared FGN were detailed characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) etc. The obtained FGN was used as a cathode material for primary lithium ion batteries with superior discharge specific capacity (eg. 979.3 mAhg-1), stable discharge platform and high energy density (eg. 2287.9 Wh kg-1), which fosters it a high density, low cost and durable candidate for cathode material for lithium ion batteries..

In this paper, the lamellar structural evolution and microvoids variations of β-iPP during the processing of two different stretching methods, sequential biaxial stretching and simultaneous biaxial stretching, were investigated in detail. It was found that different stretching methods led to significantly different lamellae deformation modes, and the microporous membranes obtained from the simultaneous biaxial stretching exhibited better mechanical properties. For the sequential biaxial stretching, abundant coarse fibers originated from the tight accumulation of the lamellae parallel to the longitudinal stretching direction, whereas the lamellae perpendicular to the stretching direction were easily deformed and separated. Those coarse fibers were difficult to be separated to form micropores during the subsequent transverse stretching process, resulting in a poor micropores distribution. However, for the simultaneous biaxial stretching, the β crystal had the same deformation mode, that is, the lamellae distributed in different directions were all destroyed, forming abundant microvoids and little coarse fibers formation.

Materials characterised by magnetorheological properties are non-classic engineering materials. A significant increase in the interest of scientific community in materials from this group can be observed over the recent several years. The results of research presented in this article are oriented on the examination of said materials’ mechanical properties. In order to do so, stress relaxation tests were conducted on cylindrical samples of magnetorheological elastomers loaded with compressive stress for various values of magnetic induction (B1 = 0 mT, B2 = 32 mT, B3 = 48 mT, and B4 = 64 mT) and temperature (T1 = 25° C, T2 = 30° C, and T3 = 40° C). The results of these tests indicate that the stiffness of examined samples increases along with the increase of magnetic field induction and decreases along with the increase of temperature. On this basis, it has been determined that: the biggest stress amplitude change caused by the influence of magnetic field was σ0ΔB = 12.7% and the biggest stress amplitude change caused by the influence of temperature was σ0ΔT = 11.3%. As a result of applying a mathematical model, it has been indicated that the stress relaxation in the examined magnetorheological elastomer for the adopted time range (t = 3600 s) has a hyperbolic decline nature. The collected test results point to examined materials being characterised by extensive rheological properties, which leads to a conclusion that it is necessary to conduct further tests in this scope.

Reinforcement corrosion due to chloride attack is of major economic significance for reinforced concrete structures. Pozzolans are known to inhibit corrosion initiation mainly by reducing concrete permeability. However, there is evidence in the literature that changes in the chemical environment in the concrete due to the pozzolans may be creating improved corrosion resistance, by themselves. In this study, the composition of a pore solution of mature hydrated cement paste containing silica-fume at different ratios was analyzed. The electrochemical behavior of reinforcing steel was studied in simulated pore solutions with silicate concentrations ranging from 0 to 35.6 mM, which are within the concentration range found by pore solution extraction to be up to 49 mM. Polished reinforcing steel specimens were used for cyclic voltammetry in simulated pore solutions with chloride concentrations of 10-20%. Better corrosion protection was found with increasing silicate concentration up to 3.56 mM. This was indicated by lower corrosion currents both in the passive state and after anodic activation. Anodic activation of steel in a 35.6 mM silicate solution with 20% NaCl yielded a higher potential than the anterior potential.

This paper reviews state of the art Additive Manufactured (AM) IN718 alloy intended for high temperature applications. AM processes have been around for decades and have gained traction in the past five years due to the huge economic benefit it brings to manufacturers. It is crucial for the scientific community to look into AM IN718 applicability in order to see a step-change in the production. Microstructural studies reveal that the grain structure plays a significant role in determining the fatigue lifespan of the material. Controlling IN718 respective phases such as the ϒ’', δ and Laves phase is seen to be crucial. Literature reviews have shown that the mechanical properties of AM IN718 were very close to its wrought counterpart when treated appropriately. Higher homogenization temperature and longer ageing were recommended to dissolve the damaging phases. Various surface enhancement techniques were examined to find out their compatibility to AM IN718 alloy that is intended for high temperature application. Laser shock peening (LSP) technology stands out due to the ability to impart low cold work which helps in containing the beneficial compressive residual stress it brings in high temperature fatigue environment.

An effective method for coating textile fabrics with porous materials is proposed, and the removal rates of nitrogen oxides (NOx), sulfur oxides (SOx), and fine dust particles in the coated textile fabrics are evaluated. The textile fabrics made of polyester are used to effectively reduce fine dust particles through static electricity. Zeolite and coconut shell activated carbon are used as porous material to reduce SOx and NOx, respectively. The effects of the epoxy content and dilution solution types on the SOx removal rate of textile fabrics coated with zeolite are evaluated to determine the optimum coating conditions. In addition, the effects of external environmental conditions, such as washing and freeze thawing, on the SOx and NOx removal rates of the textile fabrics coated with porous materials using the optimum coating conditions are examined. The test results show that the SOx removal rate of textile fabrics coated with zeolite decreases with the increase in the epoxy content. The decrease is 2.9 times larger for textile fabrics coated using deionized water than those coated using isopropyl alcohol. After one wash, the SOx removal rate decreases dramatically. However, the decrease is reduced by 16% when the epoxy content ratio is increased by 0.5%. The effects of washing and freeze thawing on the SOx and NOx removal rates of textile fabrics coated using the deionized water diluted with the epoxy content ratio of 2% are minimal. Consequently, to maintain stable SOx and NOx removal rates under external environmental conditions such as washing and freeze thawing, 98% deionized water dilution and 2% epoxy content ratio are required for the optimum coating of textile fabrics with zeolite and coconut shell activated carbon.

Porous ultra-high molecular weight polyethylene (UHMWPE) is a high performance bioinert polymer used in cranio-facial reconstructive surgery in procedures where relatively low mechanical stresses arise. As an alternative to much stiffer and costly polyether-ether-ketone (PEEK) polymer, UHMWPE finds further wide application in hierarchically structured hybrids for advanced implants mimicking cartilage, cortical and trabecular bone tissues within a single component. The mechanical behaviour of open-cell UHMWPE sponges obtained through sacrificial desalination of hot compression-moulded UHMWPE-NaCl powder mixtures shows a complex dependence on the fabrication parameters and microstructural features. In particular, similarly to other porous media it displays significant inhomogeneity of strain that readily localises within deformation bands that govern the overall response. In this article, we report advances in the development of accurate experimental techniques for operando studies of the structure-performance relationship applied to the porous UHMWPE medium with pore sizes of about 250 µm that are most well-suited for live cell proliferation and fast vascularization of implants. Samples of UHMWPE sponges were subjected to in situ compression using a micromechanical testing device within Scanning Electron Microscope (SEM) chamber, allowing the acquisition of high-resolution image sequences for Digital Image Correlation (DIC) analysis. Special masking and image processing algorithms were developed and applied to reveal the evolution of pore size and aspect ratio. Key structural evolution and deformation localisation phenomena were identified at both macro- and micro-structural levels in the elastic and plastic regimes. The motion of pore walls was quantitatively described, and the presence and influence of strain localisation zones were revealed and analysed using DIC technique.

This article focuses on the issue of motor oils used in the engines of off-road mobile machinery (NRMM), more specifically tractors. The primary goal of the paper is to determine the appropriate replacement interval for these oils. The physical properties of the examined samples were first determined by conventional instruments. Furthermore, the concentration of abrasive metals, contaminants, and additive elements were measured using an optical emission spectrometer. Lastly, the content of water, fuel, glycol, and the products of oxidation, nitration, and sulphation were determined by using infrared spectrometry. The measured values were compared to the limit values. Based on the processing and evaluation of these analyses, the overall condition of the oils was assessed and subsequently the optimal exchange interval of the examined oils was determined. In addition, a risk analysis of the outage was performed. Due to the high yields of crops, farmers can lose a significant amount of product when a tractor is not functioning during the harvest period. This loss for calculated in the paper.

We reported previously that poly (3-hydroxybutyrate) (PHB) oligomer is an effective antimicrobial agent against gram-positive bacteria, gram-negative bacteria, fungi and multi-drug resistant bacteria. In this work, it was further found that polyethylene glycol (PEG) can promote the antimicrobial effect of PHB oligomer synergistically. Three hypothetic mechanisms were proposed, that is, generation of new antimicrobial components, degradation of PHB macromolecules and dissolution/dispersion of PHB oligomer by PEG. With a series of systematic experiments and characterizations of HPLC-MS, it was deducted that dissolution/dispersion of PHB oligomer dominated the synergistic antimicrobial effect between PHB oligomer and PEG. This work demonstrates a way for promoting antimicrobial effect of PHB oligomer and other antimicrobial agents through improving hydrophilicity.

The popularity of functional gummies has increased, which is evident from the growing line of functional gummies from almost every nutraceutical companies. Sensory evaluation serves the purpose of determining which brand of functional gummy would capture the largest market share. Texture profile analysis was used to determine the mechanical properties of functional gummies. The brands of functional gummies that came under the scope of this study were denoted as Brand A, B, C, D, E, F and G. Fourier Transform Infrared Spectroscopy was utilised to detect organic material and functional groups in the functional gummies. Texture profile analysis gave valuable insights into the gummies’ mechanical properties which are cohesiveness, springiness, hardness, gumminess, and chewiness. Amongst the gummies that were studied, Brand F gummy has the highest value of cohesiveness of 0.92. Brand A gummy has a high springiness value of 1.0. Brand B gummy possesses the highest value of hardness, gumminess and chewiness of 12 532.2 g, 7617.6 N, and 6256.8 J, respectively. Qualitative sensory evaluation reveals that Brand G gummy has the best aesthetic qualities in terms of colour and appearance. Brand B gummy tastes the best while brand A gummy claims the top spot for gumminess and chewiness. Overall, the respondents in this study preferred brand A gummy over other brands.

Mining-induced water contamination remains a significant concern in many regions of the world due to the high concentrations of toxic ions often associated with it. In this study, cellulose-supported ferrihydrite composites (CNF-Fe) were prepared by seeding of ferrihydrite nanoparticles on cellulose nanofibres (CNFs) and employed for the removal of As(III), As(V) and Cr(VI) from contaminated water. The adsorbent was characterized by electron microscopy, gas adsorption, point of zero charge (pH_PZC), X-ray diffractometry (XRD), as well as infrared and Raman spectroscopy. Compared to parent CNFs, CNF-Fe adsorbents had lower crystallinity and a higher surface area: 218.76 m² g^-1. Further, with a pH_PZC of 6.3, CNF-Fe was positively charged at low pH and suitable for adsorption of anions at acidic conditions characteristic of acid mine drainage. In single-ions solutions, the removal efficiency of CNF-Fe was in the order Cr(VI)>As(V)>As(III) (i.e. 0.15, 0.12 and 0.11 mg g^-1 respectively). Adsorption kinetics followed the pseudo second-order model and isotherms were best fitted by the Freundlich, Dubinin-Radushkevich, and Temkin models. However, when CNF-Fe was applied to AMD-contaminated water (pH 2.7), Cr(VI) uptake decreased to ~39% which was likely due to competition from sulphate and selenium ions. Nevertheless, the adsorbent displayed regeneration capabilities with ~98% As and ~45% Cr desorbed after 24 hours of treatment. Together, these results suggest that cellulose supported ferrihydrite composites can be applied in treatment of mine drainage-contaminated water in conjunction with pre-treatments that limit SO₄^2- and selenium concentrations.

Tin oxide (SnO2) thin films, undoped single-layer and fluorine doped / undoped bilayer were deposited by Atmospheric Pressure Chemical Vapour Deposition (APCVD) at soda-lime glass substrate at two different temperatures (590°C and 610°C). Transport properties examined by impedance spectroscopy, DC resistivity, Hall effect and magnetoresistance measurements are correlated with structural properties examined by Scanning Electron Microscopy, Grazing Incidence X-ray Diffraction (GIXRD) and Time-of-flight Elastic Recoil Detection Analysis (TOF-ERDA). Results suggest that charge transport in the obtained samples is dominated by scattering at neutral impurities and can be correlated with preferred orientation (texture coefficient) presented in prepared samples.

Nowadays, we can observe a worldwide trend towards the development of synthetic biomaterials. Numerous researches have been carried out in order to better understand the cellular behavior involved in the inflammation and bone healing processes related to living tissues. The aim of this study is to evaluate the tissue behavior of two different types of biomaterials: synthetic nano-hydroxyapatite / beta-tricalcium phosphate and hydroxyapatite in non-critical bone defects in rat calvaria. Twenty four rats underwent surgery in which two 3 mm defects in each cavity were performed. The rats were divided into 2 groups: Group 1, using xenogen hydroxyapatite (Bio oss ™); Group 2, using synthetic nano-hydroxyapatite / beta-tricalcium phosphate (Blue Bone ™). Sixty days after the surgery, the calvaria bone defect was filled with biomaterial, the animals were sacrificed and marked with Masson's trichrome and PAS staining, and immunohistochemistry (TNF-α, MMP-9) and electron microscopy analyzes were performed. Histomorphometric analysis indicates a greater presence in the protein matrix in Group 2, in addition to higher levels of TNF-α, MMP-9. The ultrastructural analysis shows an association of material with fibroblasts in the tissue regeneration stage. Paired statistical data indicates that Blue Bone ™ can improve bone formation / remodeling when compared to biomaterials of xenogenous origin.

To expand the application scope and increase the demand for non-crimp fabrics (NCFs) as a lightweight vehicle material, the delamination and thermal strain in NCF composites must be restricted. Accordingly, to simultaneously improve the interfacial bonding and thermal stability of the NCF composites, in this study the epoxy resin, in which SiO2 nanoparticles was modified by a silane coupling agent, were infused to the stacked NCFs and between the layers of NCFs through the vacuum-assisted resin infusion molding (VARIM) process.

Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

The lack of suitable autologous grafts and poor compliance of existing prostheses have prompted the study of novel materials for vascular graft design. Polyurethanes (PUs) were used in the past because they have high compliance and properties that are similar to those of native tissue. In this work, the mechanical properties of a group of PUs in two states (non-hydrated and hydrated) were studied using uniaxial tensile tests, strain sweep tests, and multi-step creep recovery tests. Additionally, a hyper-elastic model based on the Mooney–Rivlin strain density function was fitted and used to model the performances of the PUs under physiological pressure and geometry conditions. The tensile tests revealed a softening phenomenon after hydration, which could potentially reduce patient discomfort and risk of vascular trauma. The ultimate strength values after hydration were similar to those reported for other vascular conduits. The strain sweep showed a strong strain dependency of the modulus indicating non-linear viscoelasticity. In the creep-recovery tests, increasing the polyethylene glycol(PEG) content enhanced the viscous flow, while the elastic behavior was enhanced with the largest concentration of polycaprolactone diol (PCL). On the other hand, under simulated physiological conditions, the compliance of the PUs showed a cyclic behavior with the time and pressure but was not affected by the radii and thickness variation, which could increase the graft compliance and geometry mismatch. Nevertheless, the compliance could be tuned using the material composition. This paper studied the biomechanics of a group of materials under simulated physiological conditions (Temperature, hydration, and pressure) to select those that could perform better for further vascular graft design.

Gastrointestinal tumors including pancreatic and colorectal cancers represent one of the greatest public health issues worldwide, leading to million global deaths. Recent research demonstrated that the human heavy chain ferritin (HFt) can encapsulate different type of drugs in its cavity and can bind to its receptor, CD71, in several solid and hematological tumors, thus highlighting the potential use of ferritin for tumor-targeting therapies. Here, we describe the development and characterization of a novel nanomedicine based on the HFt that is named The-0504. In particular, this novel system is a nano-assembly comprising an engineered version of HFt that entraps about 80 molecules of a potent, wide-spectrum, non-camptothecin topoisomerase I inhibitor (Genz-644282). The-0504 can be produced by a standardized pre-industrial process as a pure and homogeneously formulated product with favourable lyophilization properties. The preliminary anticancer activity was evaluated in cultured cancer cells and in a mouse model of pancreatic cancer. Overall results reported here make The-0504 a candidate for further preclinical development against CD-71 expressing deadly tumors

We report on space-selective crystallization of congruent and polar Sr2TiSi2O8 crystals in a stoichiometric SrO-TiO2-SiO2 glass induced by (1030 nm, 300 fs) femtosecond laser irradiation. This allows us to compare with non-congruent laser induced crystallization of polar LiNbO3, in non stoichiometric Li2O-Nb2O5-SiO2 glass and gain information on the mechanism of nanocrystals orientation with the laser polarization that we pointed out previously. Using scanning electron microscopy (SEM), Second-harmonic generation (SHG) and electron backscattered diffraction (EBSD), we studied the laser induced crystallization according to the laser processing parameters (pulse energy, pulse repetition rate, scanning speed). We found 1) a domain where the laser track is filled with crystals not perfectly textured (low energy), 2) a domain where an amorphous volume remain surrounded by a crystallized shell (high energy). This arises from Sr out-diffusion and may gives rise to crystallization of both SrTiO3 and Sr2TiSi2O8 phases at low speed. In the one-phase domain (at higher speed), it is found the possibility to elaborate a tube with a perfect fresnoite texture. Significant difference in size and morphology whereas crystallization threshold remains similar are discussed based on glases thermal propeties. Contrarily to Li2O-Nb2O5-SiO2 (LNS) glass, no domain of oriented nanocrystallization controlled by the laser polarization has been found in SrO-TiO2-SiO2 (STS) glass, which is attributed to the larger crystallization speed in STS glass. No nanogratings have also been found that is likely due to the congruency of the glass.

Polyhydroxyalkanoate (PHA) co-polymers show relatively higher in vivo degradation rate compared to other PHAs thus they received a great deal of attention for a wide range of medical applications. Nanoparticles (NPs) loaded with poorly water soluble anticancer drug docetaxel (DCX) were produced using poly 3-hydroxybutyrate-co-4-hydroxybutyrate, P(3HB-co-4HB), co-polymers biosynthesised from Cupriavidus sp. USMAA1020 isolated from Malaysian environment. Three co-polymers with different molar proportions of 4-hydroxybutirate (4HB) were used: 16% (PHB16), 30% (PHB30) and 70% (PHB70) 4HB-containing P(3HB-co-4HB). Blank and DCX loaded nanoparticles were then characterized for their size and size distribution, surface charge, encapsulation efficiency and drug release. Pre-formulation studies showed that an optimised formulation could be achieved through the emulsification/solvent evaporation method using PHB70 with the addition of 1.0% PVA, as stabilizer and 0.03% VitE-TPGS, as surfactant. DCX-loaded PHB70 nanoparticles (DCX-PHB70) gave the desired particle size distribution in term of average particles sizes around 150 nm and narrow particle size distribution (PDI below 0.100). The encapsulation efficiencies result showed that at 30% w/w drug-to-polymer ratio: DCX- PHB16 NPs were able to encapsulate up to 42% of DCX; DCX-PHB30 NPs encapsulated up to 46% of DCX and DCX-PHB70 NPs encapsulated up to 50% of DCX within the nanoparticles system. Approximately 60% of DCX was released from the DCX-PHB70 NPs within 7 days for 5%, 10% and 20% of drug to polymer ratio while for the 30% and 40% drug to polymer ratios, an almost complete drug release (98%) after 7 days of incubation was observed.

Cationised hemp cellulose was prepared by etherification with two quaternary ammonium salts: 3-chloro-2-hydroxypropyl trimethyl ammonium chloride (CHPTAC) and glycidyltrimethylammonium chloride (GTMAC) and examined for (i) the efficiency of Cr(VI) removal under acid mine-drainage (AMD) conditions, and (ii) antibacterial activity. Adsorbents were characterised by electron microscopy, Fourier transform infrared (FTIR), CP-MAS ¹³C nuclear magnetic resonance (NMR) spectroscopy, elemental composition and surface charge. FTIR and solid state ¹³C NMR confirmed the introduction of quaternary ammonium moieties on cellulose. ¹³C NMR also showed that cationisation decreased the degree of crystallisation and lateral dimensions of cellulose fibrils. Nevertheless, 47 % - 72% of Cr(VI) ions were removed from solutions at pH 4, by 0.1 g of CHPTAC and GTMAC-cationised cellulose, respectively. Adsorption kinetics followed the pseudo-second order model and isotherms were best described by the Freundlich and Dubinin-Radushkevich models. When GTMAC-modified cellulose was applied to AMD contaminated water (pH 2.7), however, Cr(VI) uptake removal decreased to 22% likely due to competition from Al and Fe ions. Nevertheless, cationised materials displayed considerable antibacterial effects, reducing the viability of Escherichia coli by up to 45 % after just 3 hours of exposure. Together, these results suggest that cationised cellulose can be applied in the treatment of Cr(VI)-contaminated mine water particularly if pre-treatments to reduce Fe and Al concentrations are applied.

Fabrics treated to repel water, superhydrophobic, and water and oil, superamphiphobic, have numerous industrial and consumer-level benefits. These coatings are typically non-permanent. This is largely due to chemical or physical changes of the coating to prolonged exposure to relatively harsh environments. To develop more durable fabric treatments for specific applications, it is necessary to measure the extent to which the treated fabrics retain their low-wettability after being subjected to controlled aggressive environmental conditions. In this study, plain weave fabrics made from polyester filaments and coated with silicone nanofilaments in-solution were exposed to aerodynamic icing conditions. The coated fabrics showed superhydrophobic behavior, or superamphiphobic for those that were fluorinated. The wettability of the fabrics was progressively evaluated by contact angle and roll-off-angle measurements. The fabrics were able to maintain their low-wettability characteristics after exposure to water droplet clouds at airspeeds up to 120 m/s, despite damage to the silicone nanofilaments, visible through scanning electron microscopy.

Together with display and input, storage and processing are requisite to computing. While storage technologies have improved tremendously in capacity and speed over the years, the basic principles enabling information storage into digital 1 and 0 remains the same: induction of phase change in the storage substrate. But recently, there has been much research into structural phase change material (SPCM) and exploration of its possible use in various types of memory storage applications. Despite unconventional use of structural change between amorphous and crystalline state as well as that between crystal structures for encoding information, key barriers for its widespread use remains access speed, capacity to cost ratio, and fidelity of storage. Hence, given the performance requirement of SPCM for memory applications, what are the material and design considerations that feed into translating a promising application into a practical reality? Given the important role of kinetic and thermal energy in structural organization of a phase change material, precise characterization of structural change in the material with external physical factors such as heat, voltage and current, is critical for storage material design. Next comes the precision at which individual memory cells for storing single bits of information could be defined reproducibly and at high fidelity using SPCM. In congruent with memory cell definition lies the equally important aspect of constraining the field characteristics used in modulating the phase state of the memory medium. Specifically, while heat is useful for mediating the “melting” of a crystalline material into its amorphous state, heat conduction is less useful for transferring the “switch command” from the effector to the memory material. More importantly, choice of structural phase change material for memory applications likely revolves around those where individual memory cells could be defined in a cross array format, which is amenable to high density information storage. Durability and fidelity of information storage are additional factors of design that favours selection of SPCM with phase change occurring at narrow operating windows without hysteresis over extended cycling. But, the most important requirement is speed of access. To this end, energetic cost of phase transitions might affect operation of the phase change memory at the system level: for example, usage of large current for high energy transition step may impact on device durability. Ultimately, there is a fundamental limit on the number of reproducible phase transitions in a SPCM before fidelity of information storage is no longer guaranteed. Hence, what are the drivers for uptake of phase change memories in consumer devices? Performance gains must be realized in access speed, storage capacity, form factor, and fidelity of information storage for practical application of structural phase change memories.

Nano Silicon carbide reinforced aluminum (Al/nanoSiC) metal matrix composites are attractive because of their superior properties such as high strength and stiffness, Application of aluminum in technological and structural application is growing steadily. The major limitation for metal matrix nano composites, however, is their propensity to brittle fracture. The new technologies and new materials are two basic aims for companies. In this research, the effect of addition Al/SiC nano particles on microstructure and mechanical properties of pure aluminum has been investigated. Pure aluminum powder and various fractions of SiC particles with an average diameter of 50 nm were milled by a high-energy planetary ball mill to produce nanocrystalline Al–SiC nanocomposite powders. Pressing and sintering applied to consolidate powders to tablet shape. Then the samples were rolled to cylindrical shape. The nano SiC Percentage were 0%, 2.5%, 5%, 7.5%, 10% , 12,5% and 15%. Mechanical tests such as tensile, hardness, fracture toughness and young’s modules measurement carried out to study the mechanical behavior of each alloy. Scanning electron microscopy was used to study the morphology and microstructure of nanocomposite powders and bulk samples. The role of wt% fraction of SiC nanoparticles was investigated. The results shows that the addition of SiC nano particles has significant influence on the microstructure and mechanical properties of composites and usually the optimum properties depends on wt% SiC.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

The remarkable adsorption capacity of graphene derived materials has prompted their examination in composite materials suitable for deployment in treatment of contaminated waters. In this study, crosslinked calcium alginate – graphene oxide beads were prepared and activated by exposure to pH 4 by using 0.1M HCl. The activated beads were investigated as novel adsorbents for the removal of organic pollutants (Methylene Blue dye and the pharmaceuticals Famotidine and Diclofenac) with a range of physicochemical properties. Effects of initial pollutant concentration, temperature, pH and adsorbent dose were investigated and kinetic models were examined for fit to the data. Maximum adsorption capacities q_max obtained were 1334, 35.50 and 36.35 mg g^-1 for the uptake of Methylene blue, Famotidine and Diclofenac respectively. The equilibrium adsorption had an alignment with Langmuir isotherms while the kinetics were most accurately modelled using a pseudo- first –order and second order models according to the regression analysis. Thermodynamic parameters such as ΔG^◦, ΔH^◦ and ΔS^◦ were calculated and the adsorption process was determined to be exothermic and spontaneous.

Intranasal (i.n.) administration became an alternative strategy to bypass the blood-brain barrier and improve drug bioavailability in the brain. The main goal of this work was to preliminarily study the biodistribution of mixed amphiphilic mucoadhesive nanoparticles made of chitosan-g-poly(methyl methacrylate) and poly(vinyl alcohol)-g-poly(methyl methacrylate) and ionotropically crosslinked with sodium tripolyphosphate in the brain after intravenous (i.v.) and i.n. administration to Hsd:ICR mice. After i.v. administration, the highest nanoparticle accumulation was detected in the liver, among other peripheral organs. After i.n. administration of a 10-times smaller nanoparticle dose, the accumulation of the nanoparticles in off-target organs was much lower than after i.v. injection. In particular, the accumulation of the nanoparticles in the liver was 20 times lower than by i.v. When brains were analyzed separately, intravenously administered nanoparticles accumulated mainly in the “top” brain, reaching a maximum after 1h. Conversely, in i.n. administration, nanoparticles were detected in the “bottom” brain and the head (maximum reached after 2 h) owing to their retention in the nasal mucosa and could serve as a reservoir from which the drug is released and transported to the brain over time. Overall results indicate that i.n. nanoparticles reach similar brain bioavailability, though with a 10-fold smaller dose, and accumulate in off-target organs to a more limited extent and only after redistribution through the systemic circulation. At the same time, both administration routes seem to lead to differential accumulation in brain regions and thus, they could be beneficial in the treatment of different medical conditions.

Nisin is a 3.4 kDa antimicrobial peptide, produced by Lactococcus lactis (ATCC 11454). This bacteriocin can inhibit spores gemination and gram-positive bacteria development and has gained visibility in therapeutic use. The bacterial cellulose (CB) has been considered an ideal material and with high quality applied in food and medical-pharmaceutical inputs. Because of all this benefits, it is important to know the system proceeding of CB with nisin. Therefore, it was realize nisin release profile analysis of CBs was performed; analysis of the minimum inhibitory concentration (MIC) of nisin against Escherichia coli ATCC 25922, Pseudomonas aeuroginosa ATCC 9721 and Staphylococus aureus ATCC 10390; antimicrobial stability test, for 100 days at different temperatures of 4º, 25º and 37 ° C against microorganisms: S. aureus e L. sakei. The results show that nisin is released by the CB in 4 hours of contact with medium and the MIC of nisin is 78 µg/mL for S. aureus, doesn’t have gram-negative inhibition. It had stability until 100 days against L. sakei and 60 days for S. aureus. The system proved to be efficient and CB potentiated the antimicrobial action of nisin, acting as a selective barrier for other compounds present in the standard solution, serving as protection of the peptide at different temperatures. The CB loading system can be an ideal antimicrobial stability system for nisin.

The use of cow bones for biomaterial is still limited; accordingly, the cow bones waste has low economic value. Basically, a human’s and a cow’s bones are the same in terms of their forming compound. Aluminum (Al) has the potential to combine with hydroxyapatite (HAp) to make metal matrix composites (MMC) that have the potential for biomaterials. Compatible elements to be combined with Al and HAp are magnesium (Mg), titanium (Ti), and Copper (Cu), used self-high propagating temperatures synthesis (SHS). MMC can be processed to be a useful, solid product. Applying pressure to the SHS reaction and heating process may result in biomaterial composite product consisting of some matrix materials such as Al come from cans materials used in the experiment was HAp that was processed from cow bones calcination, added by can that contained aluminum and wetting agent, namely magnesium. The exothermic temperature was 800-900°C. The compaction process was done to allow materials to be bound. Based on the ASTM F138 standard for element of biomaterials, the porosity value was below 30% and hardness level above 40 HV. Cow bones and can-based composite sample with the composition of HAp-Al-Mg: 85%-10%-5% met the standard since the hardness value was: 73.3 HV with a porosity value of 29.88%.

A super-porous hybrid platform can offer significantly increased number of reaction sites for the analytes and thus can offer advantages in the biosensor applications. In this work, a significantly improved sensitivity and selectivity of hydrogen peroxide (H2O2) cancer sensor is demonstrated by a super-porous hybrid CuO/Pt NP platform. The super-porous hybrid platform is fabricated by a physiochemical approach combining the physical vapor deposition of Pt NPs and electrochemical deposition of super-porous CuO structures by adopting a dynamic hydrogen bubble technique. Under an optimized condition, the hybrid CuO/Pt biosensor demonstrates a very high sensitivity of 2,205 µA/mM∙cm2 and a low limit of detection (LOD) of 140 nM with a wide range of H2O2 detection. This is meaningfully improved performance as compared to the CuO-based H2O2 sensors as well as to the previously reported metal oxide based H2O2 sensors. The hybrid CuO/Pt platform exhibits excellent selectivity against other interfering molecules such as glucose, fructose, dopamine, and ascorbic acid. Due to the synergetic effect of highly porous CuO structures and underlying Pt NPs, the CuO/Pt architecture offers extremely abundant active sites for the H2O2 reduction and electron transfer pathways.

The results of the bibliographic analysis show that the most explored nanomaterials in dentistry are graphene and carbon nanotubes, and their derivatives. A detailed analysis and a comparative study on their applications show that, although they are quite similar, graphene based materials seem to be more promising for most of the applications of interest in dentistry. The bibliographic study also demonstrated the potential of zeolite based materials, although the low number of studies on their applications shows that they have not been totally explored, as well as other porous nanomaterials that found important applications in medicine, such as metal organic frameworks, have not been explored. Subsequently, it is expected that the research effort will concentrate in graphene and zeolite based materials in the incoming years. Thus, present review paper presents a detailed bibliographic study, with more than 200 references, in order to describe briefly the main achievements that have been described in dentistry using nanomaterials, compare and analyze them in a critical way, with the aim of predicting the future challenges.

The selection of biomaterials for biomedical application is a significant challenge. In the last few decades, various bioabsorbable and stable biopolymers have been applied for use as biomedical devices in orthopedic applications. Ultra-high molecular weight polyethylene (UHMWPE) has been extensively used in medical implants, notably in the bearings of hip, knee, and other joint prostheses, owing to its biocompatibility and high wear resistance. For the ACL graft, synthetic UHMWPE is an ideal candidate due to its biocompatibility and its extremely high tensile strength. Despite the appeal of new advanced materials such as carbon fiber, poly-ether-ether ketone, and other load-bearing materials, UHMWPE remains a primary load-bearing candidate material for ACL reconstructions because of its extremely high strength, the simplicity of the fabrication process, its biocompatibility, and low friction. However, some significant problems are observed in UHMWPE based implants, such as wear debris, and oxidative degradation due to the generation of free radicals when exposed to irradiation with gamma rays for grafting or sterilization. Various innovative methodologies have been developed to resolve those problems and enhance the properties of UHMWPE. In this review, we will explore in detail the methods for surface functionalization of UHMWPE and will apply these findings to the case study of UHMWPE for Anterior Cruciate Ligament repair.

Dentin bonding is a key in restorative dentistry. Herein, we developed self-etching two-bottle adhesive system containing 10-methacryloyloxidecyl dihydrogen phosphate monomer (MDP) and the physical, mechanical, and biocompatible properties were evaluated. The characteristics of MDP were analyzed using nuclear magnetic resonance (NMR). The water sorption and solubility, the shear-bond strengths to dentin and enamel, and cytotoxicity tests were performed. The newly blended experimental group showed the lowest thickness and water sorption and solubility values. The shear bond strength to enamel and dentin were comparable to control groups (the three other products) all test groups showed 60% of cell viability. In this study, the properties of the newly synthesized adhesive are comparable with the others. The fundamental goal of this study is to get the MDP patent released, as it is intended for domestic production. For this purpose, this dentin adhesive was developed and compared with the commercial product.

Recent years brought great focus in the field of development of extracellular vesicles (EVs) based drug-delivery systems. Considering possible applications of EVs as a drug carriers the isolation process is a crucial step. To solve problems related with EV isolation, we created and validated a new EVs isolation method – Low Vacuum Filtration (LVF) and compared it with two commonly applied procedures - differential centrifugation (DC) and ultracentrifugation (UC). EVs isolated from endothelial cells culture media have been characterized by a) transmission electron microscopy (TEM) b) nanoparticle tracking analysis (NTA), c) western blot and d) Fourier-Transform Infrared Spectroscopy (FTIR). Additionally, the membrane surface have been imaged with Environmental Scanning Electron Microscopy (ESEM). We showed that LVF is reproducible and efficient method for EVs isolation form conditioned media. Additionally, we observed correlation between ATR-FTIR spectra quality and the EVs and proteins concentration. ESEM imaging confirmed that actual pore diameter are close to the values calculated theoretically. LVF method is an easy, fast and inexpensive EVs isolation method which allows for isolation of both ectosomes and exosomes from high volume sources with good repeatability. We think that it could be an efficient alternative for commonly applied methods.

Background: Actually, resonance frequency analysis (RFA) is the most extended method for measuring implant stability. The implant stability quotient (ISQ) is the measure obtained by the different RFA devices, however, inter- and intra- rater reliability and validity of some devices remains unknown. Methods: Thirty implants were placed in 3 different pig mandibles. ISQ was measured axial and parallel with Osstell® Beacon, Penguin® and MegaISQ® by 2 different operators and one operator performed a test-retest. Intraclass correlation coefficient was calculated to assess the intra- and inter-rater reliability. Pearson correlation coefficient was used to assess the validity. Results: The higher inter- and intra- rater reliability was obtained by Penguin® when measuring axial. The highest ISQ values were obtained using Penguin® in an axial measurement; the lowest, using the MegaISQ® in an axial measurement. The highest correlation values with the other devices were obtained by MegaISQ® measuring axially. Conclusion: Penguin® had a good reliability for measuring ISQ both inter- and intra- rater. Osstell® had good validity for measuring ISQ both axial and parallel and MegaISQ® had the best validity for measuring ISQ axial.

Water-soluble and cytocompatible polymers were investigated to enhance a transporting efficiency of biomolecules into cells in vitro. The polymers composed of 2-methacryloyloxyethyl phosphorylcholine (MPC) unit, a hydrophobic monomer unit, and a cationic monomer unit bearing an amino group were synthesized for complexation with model biomolecules, siRNA. The cationic MPC polymer was shown to interact with both siRNA and the cell membrane and was successively transported siRNA into cells. When introducing 20 − 50 mol% hydrophobic units into the cationic MPC polymer, transport of siRNA into cells. The MPC units (10 − 20 mol%) in the cationic MPC polymer were able to impart cytocompatibility, while maintaining interaction with siRNA and the cell membrane. The level of gene suppression of the siRNA/MPC polymer complex was evaluated in vitro and it was as the same level as that of a conventional siRNA transfection reagent, whereas its cytotoxicity was significantly lower. We concluded that these cytocompatible MPC polymers may be promising complexation reagent for introducing biomolecules into cells, with the potential to contribute to future fields of biotechnology, such as in vitro evaluation of gene functionality, and the production of engineered cells with biological functions.

The present novel corona virus (2019-nCoV) infection has created a global emergency situation by spreading all over the world in a large scale within very short time period. The infection induced death rate is also very high. There is no vaccine or anti-viral medicine for such infection. So at this moment a major worldwide problem is that how we can control this pandemic. On the other hand, India is a high population density country, where the corona virus disease (COVID-19) has started to spread from $1^{st}$ week of March, 2020 in a significant number of COVID-19 positive cases. Due to this high population density human to human social contact rate is very high in India. So control of the pandemic COVID-19 in early stage is very urgent and challenging problem. Mathematical models are employed in this paper to study the COVID-19 dynamics, to identify the influential parameters and to find the proper prevention strategies to reduce the outbreak size. In this work, we have formulated a deterministic compartmental model to study the spreading of COVID-19 and estimated the model parameters by fitting the model with reported data of ongoing pandemic in India. Sensitivity analysis has been done to identify the key model parameters. The basic reproduction number has been estimated from actual data and the effective basic reproduction number has been studied on the basis of reported cases. Some effective preventive measures and their impacts on the disease dynamics have also been studied. Future trends of the disease transmission has been Predicted from our model with some control measures. Finally, the positive measures to control the disease have been summarized.

Three-dimensional (3D) printing techniques have received considerable focus in the area of bone engineering due to its precise control in the fabrication of complex structures with customizable shapes, internal and external architectures, mechanical strength, and bioactivity. In this study, we design a new composition biomaterial consisting of polylactic acid (PLA), and halloysite nanotubes (HNTs) loaded with zinc nanoparticles (PLA+H+Zn). The hydrophobic surface of the 3D printed scaffold was coated with two layers of fetal bovine serum (FBS) on the sides and one layer of NaOH in the middle. Additionally, a layer of gentamicin was coated on the outermost layer against bacterial infection. Scaffolds were cultured in standard cell culture medium without the addition of osteogenic medium. This surface modification strategy improved material hydrophilicity and enhanced cell adhesion. Pre-osteoblasts cultured on these scaffolds differentiated into osteoblasts and proceeded to produce a type I collagen matrix and subsequent calcium deposition. 3D printed scaffolds formed from this composition possessed high mechanical strength and showed an osteoinductive potential. Furthermore, the external coating of antibiotics not only preserved the previous osteogenic properties of the 3D scaffold but also significantly reduced bacterial growth. Our surface modification model enabled the fabrication of a material surface that was hydrophilic and antibacterial, simultaneously, with an osteogenic property. The designed PLA+H+Zn may be a viable candidate for the fabrication of customized bone implants.

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

Dynamic thermogravimetric (TG) analysis under nitrogen environment was used to understand the thermal decomposition process of 3D printing filaments made of wood-filled polylactic acid (PLA)/starch blend. The characteristic temperatures and apparent activation energy (AAE) of the filaments with various starch contents were calculated with well-known kinetic models by Friedman, Flynn-Wall-Ozawa, Coats-Redfern and Kissinger. With the increased starch content in the filament, the onset thermal decomposition temperatures of the filaments decreased gradually from 272.4 to 155.1°C. The thermal degradation degree became smaller, and the transitional temperature interval became larger with increased starch proportion. The AAE values of the three types of filaments with different starch ratios varied between 97 kJ/mol and 114 kJ/mol, depending on material composition and method of calculation. The improved understanding of thermal decomposition behavior of PLA-starch-wood composites can help develop more biodegradable PLA/starch-based filaments for 3D printing.

This study was aimed at investigating the protective effects of glass ionomer cement (GIC) and surface pre-reacted glass ionomer (S-PRG) fillers used as dental restorative materials on demineralization of bovine enamel. GlasIonomer FX ULTRA (FXU), Fuji IX GP Extra (FIXE), CAREDYNE RESTORE (CDR) were used as GICs. PRG Barrier Coat (BC) was used as the S-PRG filler. They were incubated in a lactic acid solution (pH = 4.0) for 6 d at a temperature of 37 °C. The mineral was etched from the enamel surface, and a large number of Ca and P ions were detected in solution. The Al, F, Na, Sr, and Sr ions were released in GICs and S-RPG fillers. The Zn ion was released only in CDR and the B ion was released only in BC. The presence of apparent enamel prism peripheries was observed after 6 d of treatment for the group containing only enamel blocks. pH values for the FXU, FIXE, CDR, BC, and enamel block groups after 6 d were 6.5, 6.6, 6.7, 5.9, and 5.1, respectively. Therefore, the observed pH neutralization effect suppressed progression of caries due to the release of several ions from the restoratives.

Sterilisation and preservation of vesicle formulations are an important consideration for their viable manufacture for industry applications, particular those intended for medicinal use. Here we undertake an initial investigation of the stability of hybrid lipid – block copolymer vesicles to common sterilisation and preservation processes, with particular interest in how the block copolymer component might tune vesicle stability. We investigate two sizes of polybutadiene-block-poly(ethylene oxide) polymers (PBd12-PEO11 and PBd22-PEO14) mixed with the phospholipid POPC considering the encapsulation stability of a fluorescent cargo and the colloidal stability of vesicle size distributions. We find that autoclaving and lyophilisation cause complete loss of encapsulation stability under the conditions studied here. Filtering through 200 nm pores appears to be viable for sterilisation for all vesicle compositions with comparatively low release of encapsulated cargo, even for vesicle size distributions which extend beyond the 200 nm filter pore size. Freeze-thaw of vesicles also shows promise for preservation of hybrid vesicles with high block copolymer content. We discuss the process stability of hybrid vesicles in terms of the complex mechanical interplay between bending resistance, stretching elasticity and lysis strain of these membranes and propose strategies for future work to further enhance the process stability of these vesicle formulations.

Silver particles are prepared by dewetting Ag films coated on glass using a fiber laser. The size of the particles is controlled in the range of 92 nm ~ 1.2 μm by adjusting the thickness of the Ag film. The structural properties and surface roughness of the particles are evaluated by means of scanning electron microscopy. In addition, the antifungal activity of the Ag particles is examined using spore suspensions of Colletotrichum gloeosporioides. It is shown that the particles with a size of 1.2 μm achieve 100% inhibition of the conidia growth of the Colletotrichum gloeosporioides after a contact time of just 5 min. Furthermore, the smaller particles also achieve a good antibacterial activity given a longer contact time. Similar results are observed in spore germination and pathogenicity tests performed on mango fruit and leaves. Overall, the results confirm that the Ag particles have an excellent antifungal effect on Colletotrichum gloeosporioides.

For voltage-gated Ca2+ channel (VGCC), its α2δ subunits are traditionally considered to be auxiliary subunits that regulates VGCC trafficking to the plasma membrane. The antiepileptic, antinociceptive and anxiolytic gabapentin (GBP) has previously been shown to bind the VGCC α2δ subunits with high affinity to disrupt VGCC trafficking. Yet, the interaction between GBP and α2δ still remains poorly understood from a structural point of view. For instance, it is not clear yet what the structural implication is of α2δ-1-bound GBP against VGCC trafficking. With a set of experimental data-driven structural analysis of the VGCC α2δ-1 and its ligand GBP, this article postulates for the first time that: 1), α2δ-1 bound GBP stabilizes the α2δ-1-GBP complex structure; 2), α2δ-1 bound GBP restrains the conformational flexibility of α2δ-1; 3), α2δ-1-bound GBP establishes an electrostatic axis consisting of Q535 (Gln535)-R241 (Arg241)-GBP (gabapentin)-D452 (Asp452), which constitutes an energetically favourable contribution towards the structural stability of the α2δ-1-GBP complex and helps restrains the conformational flexibility and local structural rigidification of α2δ-1; and 4), GBP-induced local conformational inflexibility and structural rigidification of α2δ-1 is one key step in the pharmacological disruption of VGCC trafficking by GBP.

Fabrics comprised of porous fibers could provide effective passive protection against chemical and biological (CB) threats whilst maintaining high air permeability (breathability). Here, we fabricate hierarchically porous fibers consisting of regenerated silk fibroin (RSF) and activated-carbon (AC) prepared through two fiber spinning techniques in combination with ice-templating – namely cryogenic solution blow spinning (Cryo-SBS) and cryogenic wet-spinning (Cryo-WS). The Cryo-WS RSF fibers had exceptionally small macropores (as low as 0.1 µm) and high specific surface areas (SSAs) of up to 79 m2 g-1. The incorporation of AC could further increase the SSA to 210 m2 g-1 (25 wt. % loading) whilst also increasing adsorption capacity for volatile organic compounds (VOCs).

Background: The aim of the present investigation was to evaluate the clinical success of horizontal ridge augmentation in the severely atrophic maxilla (Cawood and Howell class IV) using freeze-dried custom made bone harvested from cadaver donors tibial hemiplateau and to analyze the marginal bone level gain prior dental implants placement at 9 months after bone grafting and before prosthetic rehabilitation. Methods: A 52-year-old woman received custom made bone grafts. Patient underwent CT scans 2 weeks prior and 9 months after surgery for graft volume and density analysis. Results: The clinical and radiographic bone observations showed a very low rate of resorption after bone graft and implant placement. Conclusions: The custom-made allograft material was a highly effective modality for restoring the alveolar horizontal ridge, resulting in this way to reduce the need to obtain autogenous bone from a secondary site with predictable procedure. Further studies are needed to investigate its behavior at longer time points.

Autogenous demineralized dentin matrix (ADDM), derived from human extracted tooth, is commonly used as a bone-graft substitute to reconstruct alveolar defects when placing dental implants. The purpose of this retrospective study is to examine efficacy of ADDM in terms of surgical complications and marginal bone resorption by analyzing the medical records and radiographs of patients who received ADDM graft from 2008 to 2011 in our institute. Occurrence of complications, marginal bone loss around implants were investigated with regard to the type of defect, location of bone grafting, and types of bone graft techniques. ADDM-based bone grafting was performed on 221 sites in 82 patients and 208 implants were placed afterwards: The percentage of complications after bone grafting was 15.84%, and the implant survival rate was 95.19%. All complications were resolved with conventional treatment except for the 10 cases of osseointegration failure. The average marginal bone loss was 0.31 mm at the last examination after the average follow-up period of 7.2 years. Within the limitation of this study, the results of long-term follow-up are consistent with the short-term results of relevant studies. ADDM can produce promising clinical outcomes when used for alveolar ridge augmentation around implants.

Extensive experimental and theoretical research over the past several decades has culminated in the understanding of the mechanisms behind nanoparticle-mediated enhancements on the mechanical properties of hydrogels. This information is not only crucial to realizing applications that directly benefit from developing hydrogels with high mechanical strength, but also to guide the development of strategies to further enhance hydrogel properties by combining different approaches. In our study, we investigated the effect of combining two approaches – addition of nanoparticles and crosslinking two different polymers (to create double-network hydrogels) – on the mechanical properties of hydrogels. Our studies revealed that these approaches may be combined to synthesize hydrogel composites with enhanced properties; however, both polymers in the double-network hydrogel must strongly interact with the nanoparticles to fully benefit from the addition of nanoparticles. Moreover, the concentration of hydrogel monomers used for the preparation of the double-network hydrogels had a significant effect on the extent of nanoparticle-mediated enhancements; double-network hydrogel nanocomposites prepared using lower monomer concentrations showed higher enhancements in elastic moduli compared to those prepared using high monomer concentrations. Collectively, these results demonstrate that the hypotheses previously developed to understand the role of nanoparticles on the mechanical properties of hydrogel nanocomposites may be extended to double-network hydrogel systems and guide the development of next generation hydrogels with extraordinary mechanical properties through a combination of orthogonal approaches.

Electrospinning is known to be an effective and straightforward technique to fabricate polymer non woven matrices made of nano and microfibers. Micro patterned morphology of electrospun matrices results to be outmost advantageous in the biomedical field, since it is able to mimic extracellular matrix (ECM), and favors cell adhesion and proliferation. Controlling electrospun fibers alignment is crucial for the regenerative purposes of certain tissues, such as neuronal and vascular. In this study we investigated the impact of electrospinning process parameters on fiber alignment in tubular nanofibrous matrices made of Poly (L-lactide-co-ε-caprolactone) (PLA-PCL); a Design of Experiments (DoE) approach is here proposed in order to statistically set up the process parameters. The DoE was studied keeping constants the previously set material and environmental parameters; voltage, flow rate and mandrel rotating speed were the process parameters here investigated as variables. Orientation analysis was based on ImageJ and plugin Orientation J analysis of SEM images. The results show that voltage combined with flow rate has significant impact on electrospun fiber orientation, and the greatest orientation is achieved when all the three input parameters (voltage, flow rate and mandrel rotation speed) are at their maximum value.

Levan is a fructan-type exopolysaccharide, which is produced by many microbes from sucrose via extracellular levansucrases. The hydrocolloid properties of levan depend on its molecular weight, while it is unknown why and to which extent levan is functionally diverse in dependence of its size. The aim of our study was to get deeper insights into the size-dependent, functional variability of levan. For this purpose, levans of different sizes were produced using the water kefir isolate Gluconobacter albidus TMW 2.1191 and subsequently rheologically characterized. Three levan types could be identified, which are similarly branched, but significantly differ in their molecular size and rheological properties among each other. The smallest levan (< 107 Da) produced without adjustment of the pH exhibited Newton-like flow behavior up to a specific concentration of 25% (w/v). On the contrary, larger levans (> 108 Da) produced at pH ≥ 4.5 were shear-thinning and showed a gel like behavior at ≥ 5% (w/v). A third (intermediate) levan variant was obtained via production in buffers at pH 4.0 and exhibited the properties of a viscoelastic fluid at ≥ 5% (w/v). Our study reveals that the variable size and composition of levan are controllable and more decisive for its functionality than the amount of exerted levan.

Sol-gel route represents a valuable technique to obtain functional materials, in which organic and inorganic members are closely connected. Herein four hybrid materials, containing caffeic acid entrapped in a silica matrix at 5, 10, 15 and 20 wt%, were synthesized and characterized through FT-IR and UV-Vis spectroscopy. FT-IR analysis was also performed to evaluate the ability to induce the hydroxyapatite nucleation. Despite some structural changes occurred on the phenol molecular skeleton, hybrid materials showed scavenging properties vs DPPH and ABTS+ radicals, which was dependent on the tested dose and on the caffeic acid wt%. Finally, the SiO₂/caffeic acid materials have been proposed as valuable antibacterial agents against Escherichia coli and Enterococcus faecalis.

The use of plant extracts in the synthesis of metal nanoparticles is a very attractive approach in the field of green synthesis. To benefit from the potential synergy between the biological activities of the Moringa oleifera leaves extract and metallic bismuth, our study aimed at synthesizing bismuth nanoparticles using a hydroalcoholic extract of M. oleifera leaves as a means of green synthesis that yields nontoxic products and reduces the production of wasteful material. To this end, the M. oleifera leaves extract was treated with a bismuth nitrate pentahydrate solution. A color change from light brown to dark brown indicates the synthesis of bismuth nanoparticles. The total phenolic content in the M. oleifera leaves extract used was 23.0 ± 0.3 mg gallic acid equivalent/g of dried M. oleifera leaves powder. Antioxidant property of MO synthesised bismuth Nanoparticles was evaluated and in line with the extract used in the synthesis of NPs. The physical properties of the synthesized bismuth nanoparticles were characterized using UV-Vis spectrophotometer, FT-IR spectrometer, TEM, SEM, and XRD. The synthesized bismuth nanoparticles have a size in the range of 40.4-57.8 nm with amorphous morphology. Using DPPH and phosphomolybdate assays, our findings revealed that the M. oleifera leaves extract and the synthesized bismuth nanoparticles possess antioxidant properties. Using resazurin microtiter assay, we also demonstrate that the M. oleifera leaves extract and the synthesized bismuth nanoparticles exert potent anti-bacterial activity against Escherichia coli, Klebsiella pneumoniae, Staphylococcus aureus and Enterococcus faecalis, similarly to the inhibition exerted by Moringa extract, especially against Enterococcus faecalis (MIC values for the extract: 500, 250, 250, and 250 µg/mL; MIC values for the bismuth nanoparticles: 500, 500, 500, and 250 µg/mL, respectively). Similarly, the M. oleifera leaves extract and the synthesized bismuth nanoparticles display relatively stronger anti-fungal activity against Aspergillus niger, Aspergillus flavus, Candida albicans, and Candida glabrata (MIC values for the extract: 62.5, 62.5, 125, and 250 µg/mL; MIC values for the bismuth nanoparticles: 250, 250, 62.5, and 62.5 µg/mL, respectively). Thus, the hydroalcoholic extract of M. oleifera leaves was successfully used in the synthesis of bismuth nanoparticles, showing a positive antioxidant, anti-bacterial, and anti-fungal activity. Therefore, the synthesized bismuth nanoparticles can potentially be employed in the alleviation of symptoms associated with oxidative stress and in the topic treatment of Candida infections.

Natural fibers are a gift from nature that we yet fully utilized until now. It can be classified into several groups and bast fibers are the group having the most promising performance when reinforced in polymer composites. However, numerous factors have been reported that influences mechanical properties of fiber reinforcements in the composite. In this review, bast fiber retting process and the effect of enzymatic retting on fiber and fibers reinforced polymer composites have been discussed and reviewed for the latest researches. Retting precedes mechanical processing (i.e. scutching) of the fiber from the stem and is essential for reduction of fiber breakage. All retting methods except chemical retting process are involving secretes of enzymes by bacteria or fungi under controlled (enzymatic retting) or random conditions (water and dew retting). Besides, enzymatic retting is claimed to have more environmentally friendly wastewater products, shorter retting period and controllable fiber biochemical components under mild incubation conditions. This review comprehensively assesses the enzymatic retting process for producing high-quality bast fiber and will become a reference for future development on bast fiber reinforced polymer composites.

The isolation and characterization of chitin (CHI) obtained from Vespa velutina (CHIVV) is described. Moreover, a trapping procedure is presented to selectively catch the invasive species. The chitin contents of dry Vespa velutina was observed to be 11.7 %. The physicochemical properties of CHIVV was characterized by Fourier transform infrared spectroscopy (FTIR), solid-state NMR (ssNMR), elemental analysis (EA), scanning electron microscopy (SEM) and thermogravimetric analysis (TG). Obtained CHIVV is close to pure (43, 47% C, 6.94% H, and 6.85% N) and full acetylated with a value of 95.44%. Also, lifetime and kinetic parameters such as activation E and the frequency factor A using model-free and model-fitting methods, were determined. For CHIVV the solid state mechanism that follows the thermodegradation is of type F2 (Random nucleation around two nuclei). Vespa velutina chitin should not be used at temperatures above 60ºC, since its half-life would be only one year, and from an industrial point of view it would not be profitable. Based on certain factors such as the current and probable continued abundance of Vespa velutina and the quality of the product obtained, the invasive Asian hornet is a promising alternative source of chitin.

Opium poppy (Papaver somniferum L.) is an ancient medicinal plant producing pharmaceutically important benzylisoquinoline alkaloids. In the present work we focused on the study of enzyme lipoxygenase (LOX, EC 1.13.11.12) from opium poppy cultures. LOX is involved in lipid peroxidation and lipoxygenase oxidation products of polyunsaturated fatty acids have a significant role in regulation of growth, development and plant defence responses to biotic or abiotic stress. The purpose of this study was to isolate and characterize LOX enzyme from opium poppy callus cultures. LOX was purified by ammonium sulphate precipitation followed by hydrophobic chromatography using Phenyl-Sepharose CL-4B and hydroxyapatite chromatography using HA Ultrogel sorbent. SDS-PAGE analysis and immunoblotting revealed that LOX from opium poppy cultures was a single monomeric protein showing the relative molecular weight of 83 kDa. To investigate the positional specificity of the LOX reaction, purified LOX was incubated with linoleic acid and the products were analysed by high-performance liquid chromatography. LOX converted linoleic acid primarily to 13-hydroperoxy-(9Z,11E)-octadecadienoic acids (78%) and to a lesser extent to 9-hydroperoxy-(10E,12Z)-octadecadienoic acids (22%). Characterization of LOX from opium poppy cultures provided valuable information in understanding of LOX involvement in regulation of signalling pathways leading to biosynthesis of secondary metabolites with significant biological activity.

The Wolfram (W), Silicium (Si) and Molybdenum (Mo) doped Co-Cr biomedical alloy were fabricated by additive manufacturing method, which is part of powder metadology. The mixture of Wolfram (W), Silicium (Si), Chrome (Cr) and Cobalt (Co) alloy is known good wear and corrosion resistance among of biomedical applications. By addition of Molybdenum (Mo) into the structure of alloy, the structure become more stbale also increase the corrosion and wear resistance. In addition, the effects of secondary annealing process on the alloy were investigated. The microstructure of the produced alloy was analyzed by X-ray diffraction method XRD, Energy Dispersive X-Ray Analysis EDX and scanning electron microscope SEM. Moreover, Electrochemical corrosion test, micro hardness and density measurements were performed to investigate the mechanical properties of the alloy. As a result of the analyzes, the effects of Molydenum (Mo) doped and secondary annealing on the microstructure and mechanical properties of bioalloying were determined.

In this work we produced biochar by coffee waste and use it as filler in epoxy resin composite with the aim to increase their electrical properties. The biochar and biochar based composite electrical conductivity were studied in function of applied pressure and compared with carbon black and carbon black composite. The applied pressure has the aim to investigate the behaviour of filler in powder or dispersed in composite in function of compression. Results showed that even if the coffee biochar has less conductivity if compared with carbon black in powder form, it has better conductivity in composite if compared with carbon black. Composite mechanical properties were tested and they are generally improved respect to neat epoxy resin.

The combination of eco-respectful epoxy compounds with the humins, a by-product of biomass chemical conversion technologies, allow the obtention of materials with high added value. In this work, we propose the chemical connection study of humins with two aliphatic diepoxides through the copolymerization reactions to synthesize sustainable bio-based thermosets. The mechanism insights for the crosslinking between the epoxides and humins was proposed considering the different functionalities of the humins structure. FT-IR spectroscopy, 1 D and 2 D NMR spectroscopy techniques were used to build the proposed mechanism. By these techniques, the principal chain connections and the reactivity of all the components were highlighted in the synthesized networks.

Polymeric particles made up of biodegradable and biocompatible polymers such as poly(lactic-co-glycolic acid) (PLGA) are promising tools for several biomedical applications including drug delivery. Particular emphasis is placed on the size and surface functionality of these systems as they are regarded as the main protagonists in dictating the particle behavior in vitro and in vivo. Current methods of manufacturing polymeric drug carriers offer a wide range of achievable particle sizes, however, they are unlikely to accurately control the size while maintaining the same production method and particle uniformity, as well as final production yield. Microfluidics technology has emerged as an efficient tool to manufacture particles in a highly controllable manner. Here, we report on tuning the size of PLGA particles at diameters ranging from sub-micron to microns using a single microfluidics device, and demonstrate how particle size influences the release characteristics, cellular uptake and in vivo clearance of these particles. Highly controlled production of PLGA particles with ~100 nm, ~200 nm and >1000 nm diameter is achieved through modification of flow and formulation parameters. Efficiency of particle uptake by dendritic cells and myeloid-derived suppressor cells isolated from mice is strongly correlated with particle size and is most efficient for ~100 nm particles. Particles systemically administered to mice mainly accumulate in liver and ~100 nm particles are cleared slower. Our study shows the direct relation between the particle size varied through microfluidics and the pharmacokinetics behavior of particles, which provides a further step towards the establishment of a customizable production process to generate tailor-made nanomedicines.