This paper realizes early bearing fault warning through bearing fault time series prediction, and proposes a bearing fault time series prediction model based on optimized maximum correlation kurtosis deconvolution (MCKD) and long short-term memory (LSTM) recurrent neural network to ensure bearings operation reliability. The model is based on lifecycle vibration signal of the bearing, to begin, the cuckoo search (CS) is utilized to optimize the parameter filter length L and deconvolution period T of MCKD, taking into account the influence and periodicity of the bearing time series, the fault impact component of the optimized MCKD deconvolution time series is improved. Then select the LSTM learning rate α depending on deconvolution time series. Finally, the dataset obtained through various preprocessing approaches are used to train and predict the LSTM model. The average prediction accuracy of the optimized MCKD-LSTM model is 26 percent higher than that of the original time series, proving the efficiency of this method, and the prediction results track the real fault data well, according to the XI'AN JIAOTONG University XJTU-SY bearing dataset.

Human-Robot Interaction (HRI) for collaborative robots has become an active research topic recently. Collaborative robots assist the human workers in their tasks and improve their efficiency. But the worker should also feel safe and comfortable while interacting with the robot. In this paper, we propose a human-following motion planning and control scheme for a collaborative robot which supplies the necessary parts and tools to a worker in an assembly process in a factory. In our proposed scheme, a 3-D sensing system is employed to measure the skeletal data of the worker. At each sampling time of the sensing system, an optimal delivery position is estimated using the real-time worker data. At the same time, the future positions of the worker are predicted as probabilistic distributions. A Model Predictive Control (MPC) based trajectory planner is used to calculate a robot trajectory that supplies the required parts and tools to the worker and follows the predicted future positions of the worker. We have installed our proposed scheme in a collaborative robot system with a 2-DOF planar manipulator. Experimental results show that the proposed scheme enables the robot to provide anytime assistance to a worker who is moving around in the workspace while ensuring the safety and comfort of the worker.

In contrast to normal cells, tumor cells of multiple entities overexpress the Heat Shock Protein 70 (Hsp70) not only in the cytosol, but also present it on their plasma membrane in a tumor-specific manner. Furthermore, membrane-Hsp70 positive tumor cells actively release Hsp70 into lipid microvesicles termed exosomes into the blood. Due to conformational changes of Hsp70 in the lipid environment, most commercially available antibodies fail to detect membrane-bound and exosomal Hsp70. To fill this gap and to assess the role of exosomal Hsp70 in the circulation as a potential tumor biomarker, we established the novel complete Hsp70 (compHsp70) sandwich ELISA using two monoclonal antibodies (mAbs) that are able to recognize both, free and lipid-associated Hsp70 on the cell surface of viable tumor cells and exosomes. The epitopes of the mAbs cmHsp70.1 (aa 451-461) and cmHsp70.2 (aa 614-623) that are conserved among different species reside in the substrate-binding domain of Hsp70, with measured affinities of 0.42 nM and 0.44 nM, respectively. Validation of the compHsp70 ELISA revealed a high intra- and inter-assay precision, linearity in a concentration range of 1.56 to 25 ng/ml, high recovery rates of ‘spiked’ liposomal Hsp70 (>84%), comparable values between human serum and plasma samples, and no interference by food intake or age of the donors. Hsp70 concentrations in the circulation of patients with glioblastoma, squamous cell or adeno non-small cell lung carcinoma (NSCLC) at diagnosis were significantly higher than those of healthy volunteers. Hsp70 concentrations dropped concomitantly with the decrease in viable tumor mass on irradiation of patients with approximately 20 Gy (range 18 – 22.5 Gy) or after completion of radiotherapy (60 - 70 Gy). In summary, the compHsp70 ELISA presented herein provides a highly sensitive and reliable tool for measuring free and exosomal Hsp70 in liquid biopsies of tumor patients, levels of which can be used as a predictive tumor-specific biomarker, risk assessment and for monitoring therapeutic outcome.

The accurate prediction of the solar Diffuse Fraction (DF), sometimes called the Diffuse Ratio, is an important topic for solar energy research. In the present study, the current state of Diffuse Irradiance research is discussed and then three robust, Machine Learning (ML) models, are examined using a large dataset (almost 8 years) of hourly readings from Almeria, Spain. The ML models used herein, are a hybrid Adaptive Network-based Fuzzy Inference System (ANFIS), a single Multi-Layer Perceptron (MLP) and a hybrid Multi-Layer Perceptron-Grey Wolf Optimizer (MLP-GWO). These models were evaluated for their predictive precision, using various Solar and Diffuse Fraction (DF) irradiance data, from Spain. The results were then evaluated using two frequently used evaluation criteria, the Mean Absolute Error (MAE) and the Root Mean Square Error (RMSE). The results showed that the MLP-GWO model, followed by the ANFIS model, provided a higher performance, in both the training and the testing procedures.

As digitalization expands across all sectors, the economic toll of software defects on the U.S. economy reaches up to $2.41 trillion annually. High-profile incidents like the Boeing 787-Max 8 crash have shown the devastating potential of these defects, highlighting the critical importance of software testing within quality assurance frameworks. However, due to its complexity and resource intensity, the exhaustive nature of comprehensive testing often surpasses budget constraints. This research utilizes a machine learning (ML) model to enhance software testing decisions by pinpointing areas most susceptible to defects and optimizing scarce resource allocation. Previous studies have shown promising results using cost-sensitive training to refine ML models, improving predictive accuracy by reducing false negatives through addressing class imbalances in defect prediction datasets. This approach facilitates more targeted and effective testing efforts. Nevertheless, the generalizability of these models across different projects (cross-project) and programming languages (cross-language) remained untested. This study validates the model's applicability across diverse development environments by integrating various datasets from distinct projects into a unified, using a more interpretable ML approach. The results demonstrate that ML can support software testing decisions, enabling teams to identify up to seven times more defective modules with the same testing effort as a benchmark.

(1) Background: Transcription factors (TFs) are main regulators of eukaryotic gene expression. The cooperative binding of at least two TFs to genomic DNA is the widespread mechanism of transcription regulation. Massive analysis of co-occurrence of overrepresented pairs of motifs (composite elements, CEs) for different target TFs studied in ChIP-seq experiments can clarify the mechanisms of TF cooperation. (2) Methods: We focused on homotypic CEs representing the same motif models and considered only CEs with spacers. We improved the capability of the Motifs Co-Occurrence Tool (MCOT) to predict asymmetric homotypic CEs in which one of par-ticipating motifs has higher conservation than the other. We categorized the target TFs from the data of M. musculus ChIP-seq and A. thaliana ChIP-seq/DAP-seq according to the structure of DNA-binding domains (DBDs) into classes. (3) Results: For all TF classes the predominance of asymmetric CEs over both symmetric and those with no enrichment in both directions was re-vealed. Target TFs from classes Basic helix-loop-helix factors (bHLH) and Basic leucine zipper factors (bZIP) showed the highest fractions of datasets with asymmetric CEs. We showed that pioneer TFs, despite their DBD types, have a higher significance of asymmetry within homotyp-ic CEs compared to other TFs. (4) Conclusion: Asymmetry within homotypic CEs is a promising new feature decrypting the mechanisms of gene transcription regulation.

Camptothecin (CPT) is a potent anticancer drug, and its putative oral administration is envisioned although difficult due to physiological barriers that must be overcome. A comprehensive biophysical analysis of CPT interaction with biointerface models can be used to predict some pharmacokinetic issues after oral administration of this or other drugs. To that end, different models were used to mimic the phospholipid composition of normal, cancer, and blood-brain barrier endothelial cell membranes. The logD values obtained indicate that the drug is well distributed across membranes. CPT-membrane interaction studies also confirm the drug’s location at the membrane cooperative and interfacial regions. The drug can also permeate membranes at more ordered phases by altering phospholipid packing. The similar logD values obtained in membrane models mimicking cancer or normal cells imply that CPT has limited selectivity to its target. Furthermore, CPT binds strongly to serum albumin, leaving only 8.05% of free drug available to be distributed to the tissues. The strong interaction with plasma proteins, allied to the large distribution (VDSS=5.75 ± 0.932 L·Kg-1) and tendency to bioaccumulate in off-target tissues, were predicted to be pharmacokinetic issues of CPT, implying the need to develop drug delivery systems to improve its biodistribution.

Google Trends data can be informative for infectious disease incidences, including Lyme disease. However, the use of Google Trends for predictive purposes is underutilized. In this study, we tested the ability of Google Trends search data to predict monthly state-level Lyme disease case counts in the United States. We requested Lyme disease data for the years 2010-2021. We downloaded Google Trends search data on terms for Lyme disease, symptoms of Lyme disease, and diseases with similar symptoms as Lyme disease. We built mixed negative binomial models based on a training dataset (2010-2016) and tested the models on a test dataset (2017-2021). A model was built for each search term and monthly lags of search terms were included as predictors. The highest performing models had high predictive ability, indicated by low Root Mean Squared Errors (RMSEs) and close association between observed and predicted case counts. The highest performing model was for the search term “Summer Flu”, which indicates low specificity of some of the terms. We outline challenges of using Google Trends data, including data availability and a mismatch between geographic units. We discuss opportunities for Google Trends data, including prediction of additional zoonotic diseases and incorporating environmental and companion animal data.

Machine learning (ML) methods has recently contributed very well in the advancement of the prediction models used for energy consumption. Such models highly improve the accuracy, robustness, and precision and the generalization ability of the conventional time series forecasting tools. This article reviews the state of the art of machine learning models used in the general application of energy consumption. Through a novel search and taxonomy the most relevant literature in the field are classified according to the ML modeling technique, energy type, perdition type, and the application area. A comprehensive review of the literature identifies the major ML methods, their application and a discussion on the evaluation of their effectiveness in energy consumption prediction. This paper further makes a conclusion on the trend and the effectiveness of the ML models. As the result, this research reports an outstanding rise in the accuracy and an ever increasing performance of the prediction technologies using the novel hybrid and ensemble prediction models.

To minimise environmental impact, avoid regulatory penalties, and improve competitiveness, energy-intensive manufacturing firms require accurate forecasts of their energy consumption so that precautionary and mitigation measures can be taken. Deep learning is widely touted as a superior analytical technique to traditional artificial neural networks, machine learning, and other classical time series models due to its high dimensionality and problem solving capabilities. Despite this, research on its application in demand-side energy forecasting is limited. We compare two benchmarks (Autoregressive Integrated Moving Average (ARIMA), and an existing manual technique used at the case site) against three deep learning models (simple Recurrent Neural Networks (RNN), Long Short-Term Memory (LSTM), and Gated Recurrent Unit (GRU)) and three machine learning models (Support Vector Regression (SVM), Random Forest, and K-Nearest Neighbors (KNN)) for short term load forecasting (STLF) using data from a Brazilian thermoplastic resin manufacturing plant. We use the grid search method to identify the best configurations for each model, and then use Diebold-Mariano testing to confirm the results. Results suggests that the legacy approach used at the case site is the worst performing, and that the GRU model outperformed all other models tested.

Remaining service life (RSL) of pavement, as a sign of future pavement performance, has always received growing attention from pavement engineers. The RSL describes the time from the moment of pavement inspection until such a time when a major repair or reconstruction is required. The conventional approach to determining RSL involves using non-destructive tests. These tests, in addition to being costly, interfere with traffic flow and compromise users' safety. In this paper, surface distresses of pavement have been used to estimate the pavement’s RSL in order to eliminate the aforementioned problems and challenges. To implement the proposed theory, 105 flexible pavement segments were taken from Shahrood-Damghan Highway (Highway 44) in Iran. For each pavement segment, the type, severity, and extent of surface damage and pavement condition index (PCI) were determined. The pavement RSL was then estimated using non-destructive tests include Falling Weight Deflectometer (FWD) and Ground Penetrating Radar (GPR). After completing the dataset, the modeling was conducted to predict RSL using three techniques include Support Vector Regression (SVR), Support Vector Regression Optimized by Fruit Fly Optimization Algorithm (SVR-FOA), and Gene Expression Programming (GEP). All three techniques estimated the RSL of the pavement by selecting the PCI as input. The Correlation Coefficient (CC), Nash-Sutcliffe efficiency (NSE), Scattered Index (SI), and Willmott’s Index of agreement (WI) criteria were used to examine the performance of the three techniques adopted in this study. In the end, it was found that GEP with values of 0.874, 0.598, 0.601, and 0.807 for CC, SI, NSE, and WI criteria, respectively, had the highest accuracy in predicting the RSL of pavement.

Pathogenicity is unknown for the majority of human gene variants. For prioritization of sequenced somatic and germline mutation variants, in silico approaches can be utilized. In this study, 84 million non-synonymous Single Nucleotide Variants (SNVs) in the human coding genome were annotated using consensus Variant Effect Prediction (cVEP) method. An algorithm, implemented as a stacked ensemble of supervised learners, performed combination of the 39 functional, conservation mutation impact scores from dbNSFP4.0. Adding gene indispensability score, accounting for differences in the pathogenicities of the variants in the essential and the mutation-tolerant genes, improved the predictions. For each SNV the consensus combination gives either a continuous-value pathogenicity score, or a categorical score in five classes: pathogenic, likely pathogenic, uncertain significance, likely benign, benign. The provided class database is aimed for direct use in clinical practice. The trained prediction models were 5-fold cross-validated on the evidence-based categorical annotations from the ClinVar database. The rankings of the scores based on their ability to predict pathogenicity were obtained. A two-step strategy using the rankings, scores and class annotations is suggested for filtering and prioritization of the human exome mutations in clinical and biological applications of NGS technology.

The different systems in the nuclear power plants (NPP) are critical and complex which requires a continuous rigorous monitoring for both normal and abnormal conditions. However, due to the nonlinearity of the dynamic behavior of these systems, implementation of artificial intelligence within the NPP components is crucial to enhance the monitoring and the predictability of the key operating parameters trend. On the other hand, lessons learned from large nuclear accident proves that a remote real-time coordination between the different stakeholders involved in the safety of the nuclear reactor is needed. This remote feature can be implemented in the existing power plants by embedding a mobile computing networks within the plant components. This network will send early warning and transmit the NPP data on real-time to different authorities such as the regulatory authority and the decision-making committees, to enhance the interpretability of the nuclear event and deliver a collaborative decision which in return mitigate the risk associated with these events and increase the overall safety of the plant. The integration of AI and mobile computing in NPP would be most of interest in countries where nuclear reactors data are challenged to reach during an accident. For instance, during the meltdown of Chernobyl, the Soviet government covered the accident from the news in an attempt to contain the consequences but there was a spread of radioactive contamination to some other Europe countries. Therefore, in the case of such scenario the implementation of mobile computing and AI would result in different outcomes as the European countries would be notified through the mobile networking and the spread of contamination would be forecasted by the AI algorithms. In this paper, we examine the different modern AI and mobile computing technologies, the different potential application, the associated features and challenges, and future work direction.

Long unpunctuated texts containing complex linguistic sentences are a stumbling block to processing any low-resource languages. Thus, approaches that attempt to segment lengthy texts with no proper punctuation into simple candidate sentences are a vitally important preprocessing task in many hard-to-solve NLP applications. In this paper, we propose (PDTS) a punctuation detection approach for segmenting Arabic text, built on top of a multilingual BERT-based model and some generic linguistic rules. Furthermore, we showcase how PDTS can be effectively employed as a text tokenizer for unpunctuated documents (i.e., mimicking the transcribed audio-to-text documents). Experimental findings across two evaluation protocols (involving an ablation study and a human-based judgment) demonstrate that PDTS is practically effective in both performance quality and computational cost.

Solar radiation prediction is an important process in ensuring optimal exploitation of solar energy power. Numerous models have been applied to this problem, such as numerical weather prediction models and artificial intelligence models. However, well-designed hybridization approaches that combine numerical models with artificial intelligence models to yield a more powerful model can provide a significant improvement in prediction accuracy. In this paper, we propose novel hybrid machine learning approaches that exploit auxiliary numerical data. The proposed hybrid methods invoke different machine learning paradigms, including feature selection, classification, and regression. Additionally, numerical weather prediction (NWP) models are used in the proposed hybrid models. Feature selection is used for feature space dimension reduction to reduce the large number of recorded parameters that affect estimation and prediction processes. The rough set theory is applied for attribute reduction and the dependency degree is used as a fitness function. We investigate the effect of the attribute reduction process with thirty different classification and prediction models in addition to the proposed hybrid model. Then, different machine learning models are constructed based on classification and regression techniques to predict solar radiation. Moreover, other hybrid prediction models are formulated to use the output of the numerical model of Weather Research and Forecasting (WRF) as learning elements in order to improve the prediction accuracy. The proposed methodologies are evaluated using a data set that is collected from different regions in Saudi Arabia.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

The conventional method used for calculating pavement condition index (PCI) has two major drawbacks: safety problems during pavement inspection, and human error. This paper proposes a method for removing these problems. The proposed method uses surface deflection data in falling weight Deflectometer test to estimate PCI. The data used in this study were derived from 236 pavement segments taken from Tehran-Qom freeway in Iran. The data set was analyzed using multi layers perceptron (MLP) and radial basis function (RBF) neural networks. These neural networks were optimized by levenberg-marquardt (MLP-LM), scaled conjugate gradient (MLP-SCG), imperialist competitive (RBF-ICA), and genetic (RBF-GA) algorithms. After initial modeling with four neural networks mentioned, the committee machine intelligent systems (CMIS) method was adopted to combine the results and improve the accuracy of the modeling. The results of analysis have been verified by the four criteria of average percent relative error (APRE), average absolute percent relative error (AAPRE), root mean square error (RMSE) and standard error (SD). The best reported results belonged to CMIS, including APRE=2.3303, AAPRE=11.6768, RMSE=12.0056, and SD=0.0210.

Paving blocks are concrete pieces placed in exposed places to the weather, which are sub-jected to loads and wear. Hence, quality control in the manufacture of paving blocks is es-sential to guarantee the properties and durability of the product in construction projects. In Ecuador, the requirements are described in the Ecuadorian technical standard "NTE INEN 3040", and tensile splitting strength is a fundamental requirement to guarantee product quality. It is analyzed using quality control measurements such as dimensions, the weight of the fresh paving block in the vibro-compacted process, and the percentage of water absorption in order to know how the variables influence and manage to predict the tensile splitting strength to avoid product non-conformity in advance, having a timely and better control of the manufacturing process. The data was obtained from a company that can produce 30 000 units per day of rectangular paving blocks with 6 cm thickness. Mul-tivariate models such as multiple linear regression, regression trees, random forests and neural networks are performed to predict the tensile splitting strength variable through two groups of predictors; the first group is the thickness mm, width mm, length mm, mass of fresh paving block g and percentage of water absorption %. The second group of pre-dictor variables is the density of the fresh paving block kg/m3 and the percentage of water absorption %. It is concluded that the multiple linear regression method performs better in predicting the first group of predictor variables with a mean square error (MSE) of 0.110086, followed by the neural network without hidden layers resulting in an MSE of 0.112198. The best method for the second set of predictors was the neural network with-out hidden layers with a mean square error ( MSE ) of 0.112402, closely followed by the multiple linear regression model with an MSE of 0.115044.

Conclusions: Our findings suggest that the NMS-E represents a valuable preoperative diagnostic tool for endometriosis, effectively correlating with the disease's severity and surgical outcomes. Incorporating the NMS-E into clinical practice could significantly enhance the management of endometriosis by addressing current diagnostic limitations and guiding surgical planning.

The combination of artificial intelligence algorithms and numerical methods has recently become popular in the prediction of macroscopic and microscopic hydrodynamics parameters of bubble column reactors. The multi inputs and outputs machine learning can cover small phase interactions or large fluid behavior in industrial domains. This numerical combination can develop the smart multiphase bubble column reactor with the ability of low-cost computational time. It can also decrease case studies for the optimization process when big data is appropriately used during learning. There are still many model parameters that need to be optimized for a very accurate artificial algorithm, including data processing and initialization, the combination of inputs and outputs, number of inputs and model tuning parameters. For this study, we aim to train four inputs big data during learning process by an adaptive neuro-fuzzy inference system or adaptive-network-based fuzzy inference system (ANFIS) method, and we consider the superficial gas velocity as one of the input variables, while for the first time, one of the computational fluid dynamics (CFD) outputs named gas velocity is used as an output of the artificial algorithm. The results show that the increasing number of input variables improves the intelligence of the ANFIS method up to , and the number of rules during learning process has a significant effect on the accuracy of this type of modeling. The results also show that propper selection of model parameters results in more accuracy in prediction of the flow characteristics in the column structure.

Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.

In this paper, the problem of predicting future failure times based on a jointly type-II censored sample from k exponential populations is considered. The Bayesian prediction intervals and point predictors were then obtained. Generalized Bayes is a Bayesian study based on a learning-rate parameter. This study investigated the effects of the learning rate parameters on the prediction results. The loss functions of squared error, Linex, and general entropy were used as point predictors. Monte Carlo simulations were performed to show the effectiveness of the learning rate parameter in improving the results of prediction intervals and point predictors.

Commercial buildings are a significant consumer of energy worldwide. Logistics facilities, and specifically warehouses, are a common building type yet under-researched in the demand-side energy forecasting literature. Warehouses have an idiosyncratic profile when compared to other commercial and industrial buildings with a significant reliance on a small number of energy systems. As such, warehouse owners and operators are increasingly entering in to energy performance contracts with energy service companies (ESCOs) to minimise environmental impact, reduce costs, and improve competitiveness. ESCOs and warehouse owners and operators require accurate forecasts of their energy consumption so that precautionary and mitigation measures can be taken. This paper explores the performance of three machine learning models (Support Vector Regression (SVR), Random Forest, and Extreme Gradient Boosting (XGBoost)), three deep learning models (Recurrent Neural Networks (RNN), Long Short-Term Memory (LSTM), and Gated Recurrent Unit (GRU)), and a classical time series model, Autoregressive Integrated Moving Average (ARIMA) for predicting daily energy consumption. The dataset comprises 8,040 records generated over an 11-month period from January to November 2020 from a non-refrigerated logistics facility located in Ireland. The grid search method was used to identify the best configurations for each model. The proposed XGBoost models outperform other models for both very short load forecasting (VSTLF) and short term load forecasting (STLF); the ARIMA model performed the worst.

An effective process monitoring strategy is a requirement for meeting the challenges posed by increasingly complex products and manufacturing processes. To address these needs, this study investigates a comprehensive scheme based on classical machine learning methods, deep learning algorithms, and feature extraction and selection techniques. In a first step, a novel deep learning architecture based on convolutional neural networks (CNN) and gated recurrent units (GRU) is introduced to predict the local weld quality based on mid-wave infrared (MWIR) and near-infrared (NIR) image data. The developed technology is used to discover critical welding defects including lack of fusion (false friends), sagging and lack of penetration, and geometric deviations of the weld seam. Additional work is conducted to investigate the significance of various geometrical, statistical, and spatio-temporal features extracted from the keyhole and weld pool regions. Furthermore, the performance of the proposed deep learning architecture is compared to that of classical supervised machine learning algorithms, such as multi-layer perceptron (MLP), logistic regression (LogReg), support vector machines (SVM), decision trees (DT), random forest (RF) and k-Nearest Neighbors (kNN). Optimal hyperparameters for each algorithm are determined by an extensive grid search. Ultimately, the three best classification models are combined into an ensemble classifier that yields the highest detection rates and achieves the most robust estimation of welding defects among all classifiers studied, which is validated on previously unknown welding trials.

Prediction models in mobility and transportation maintenance systems have been dramatically improved through using machine learning methods. This paper proposes novel machine learning models for an intelligent road inspection. The traditional road inspection systems based on the pavement condition index (PCI) are often associated with the critical safety, energy and cost issues. Alternatively, the proposed models utilize surface deflection data from falling weight deflectometer (FWD) tests to predict the PCI. Machine learning methods are the single multi-layer perceptron (MLP) and radial basis function (RBF) neural networks as well their hybrids, i.e., Levenberg-Marquardt (MLP-LM), scaled conjugate gradient (MLP-SCG), imperialist competitive (RBF-ICA), and genetic algorithms (RBF-GA). Furthermore, the committee machine intelligent systems (CMIS) method was adopted to combine the results and improve the accuracy of the modeling. The results of the analysis have been verified through using four criteria of average percent relative error (APRE), average absolute percent relative error (AAPRE), root mean square error (RMSE), and standard error (SD). The CMIS model outperforms other models with the promising results of APRE=2.3303, AAPRE=11.6768, RMSE=12.0056, and SD=0.0210.

Accurate prediction of mercury content emitted from fossil-fueled power stations is of utmost importance for environmental pollution assessment and hazard mitigation. In this paper, mercury content in the output gas of power stations’ boilers was predicted using an adaptive neuro-fuzzy inference system (ANFIS) method integrated with particle swarm optimization (PSO). The input parameters of the model include coal characteristics and the operational parameters of the boilers. The dataset has been collected from 82 power plants and employed to educate and examine the proposed model. To evaluate the performance of the proposed hybrid model of ANFIS-PSO model, the statistical meter of MARE% was implemented, which resulted in 0.003266 and 0.013272 for training and testing, respectively. Furthermore, relative errors between acquired data and predicted values were between -0.25% and 0.1%, which confirm the accuracy of the model to deal nonlinearity and representing the dependency of flue gas mercury content into the specifications of coal and the boiler type.

Background: Transcription factors (TFs) are main regulators of eukaryotic gene expression. The cooperative binding to genomic DNA of at least two TFs is the widespread mechanism of transcription regulation. Cooperating TFs can be revealed through the analysis of co-occurrence of their motifs. Methods: We applied Motifs Co-Occurrence Tool (MCOT) that predicted pairs of spaced or overlapped motifs (composite elements, CEs) for a single ChIP-seq dataset. We improved MCOT capability for prediction of asymmetric CEs with one of participating motifs possessing higher conservation than another does. Results: Analysis of 119 ChIP-seq datasets for 45 human TFs revealed that almost for all families of TFs the co-occurrence with an overlap between motifs of target TFs and more conserved partner motifs was significantly higher than that for less conserved partner motifs. The asymmetry toward partner TFs was the most clear for partner motifs of TFs from ETS family. Conclusion: Co-occurrence with an overlap of less conserved motif of a target TF and more conserved motifs of partner TFs explained a substantial portion of ChIP-seq data lacking conserved motifs of target TFs. Among other TF families, conservative motifs of TFs from ETS family were the most prone to mediate interaction of target TFs with its weak motifs in ChIP-seq.

This study investigates the latest advancements in utilizing machine learning techniques for predicting financial market movements. Financial markets are complex systems influenced by numerous factors, making accurate predictions challenging but highly valuable. The research explores various machine learning approaches, including supervised learning, unsupervised learning, reinforcement learning, and deep learning, to enhance the accuracy and reliability of financial market forecasts. The study provides a comprehensive review of current methodologies, highlighting key innovations and their applications in financial market prediction. Techniques such as neural networks, support vector machines, random forests, and ensemble methods are examined in the context of their ability to analyze vast amounts of financial data, identify patterns, and generate actionable insights. Additionally, the research delves into the integration of alternative data sources, such as social media sentiment, news articles, and macroeconomic indicators, to improve prediction models. Through empirical analysis and case studies, the study demonstrates the effectiveness of advanced machine learning models in predicting stock prices, currency exchange rates, and commodity prices. It also discusses the challenges associated with these techniques, including overfitting, data quality issues, and the need for interpretability in model outputs. Findings suggest that machine learning techniques can significantly enhance the predictive power of financial models, offering more accurate and timely insights for investors and financial analysts. The study concludes with recommendations for future research directions, emphasizing the importance of model transparency, the incorporation of diverse data sets, and the continuous adaptation of machine learning algorithms to evolving market conditions.

This article presents a comprehensive study on enhancing grid resilience through advanced forecasting and optimization techniques in the context of power outages. Power outages pose significant challenges to modern societies, affecting various sectors such as industries, households, and critical infrastructures. The research combines statistical analysis, machine learning algorithms, and optimization methods to address this issue to develop a holistic approach for predicting and mitigating power outage events. The proposed methodology involves the use of Monte Carlo simulations in MATLAB for future outage prediction, Long Short-Term Memory (LSTM) networks for forecasting solar irradiance and load profiles, and a hybrid LSTM-Particle Swarm Optimization (PSO) model to improve accuracy. Furthermore, the role of Battery State of Charge (SoC) in enhancing system resilience is explored. The study also assesses the techno-economic advantages of a grid-tied microgrid integrated with solar panels and batteries over conventional grid systems. The results highlight the potential of the proposed approach in strengthening grid resilience, reducing downtime, and fostering sustainable energy utilization.

With the availability of wearable health monitoring sensor modules like 3-Lead Electrocardiogram (ECG), Pulse Oximeter (SpO2), Galvanic Skin Response (GSR), Hall effect sensor (for measuring Respiratory Rate), Blood Pressure and Temperature measuring and sensing elements, it has now become possible to device a composite health status monitoring kit that can measure vital signs and other physiological parameters pertaining to human health in real time. Traditionally, the physiological parameters along with vital signs related examination was possible only in a hospitalized or ambulatory environment, however due to advances in sensing and embedded system technology and miniaturization of data acquisition and processing elements health monitoring has become possible even when individuals remain engaged in their day to day activities at the convenience of space and location. The patients or individuals subject to monitoring may suffer from a traumatic experience due to their medical condition and may need emergent incidence response and the critical care team may have to prepare for the treatment only after the patient arrives, which often is too late, as in case of cardiac arrests or severe injuries. The research focused on real-time health status monitoring and trauma scoring using standard physiological parameters along with standard telemetry protocols to make the critical care team aware of an emergent situation and prepare for a medical emergency. Vital signs and physiological parameters (heart rate, temperature, respiratory rate, and blood pressure, SpO2) were measured in real time from human subjects non-invasively. In order to enable monitoring of the patients engaged in day to day activities, errors due to the motion were removed using stationary wavelet transform correction (correlation coefficient of 0.9 after correction) and signals from various sensors were denoised, filtered and were encoded in a format suitable for further data analysis. A composite sensor kit capable of monitoring vital signs and physiological parameters can be very useful in incident response when an individual undergoes a traumatic experience related to stroke, cardiac arrest, fits or even injury, as along with monitoring information the kit can calculate scores related to trauma like the Injury Severity Score (ISS), National Early Warning Signs (NEWS), Revised Trauma Score (RTS). Trauma Injury Severity Score (TRISS), Probability of Survival (Ps) score. An open access database of vital signs and physiological parameters from Physionet, MIMIC 2 Numerics (mimicdb/numerics) database was used to calculate NEWS and RTS and to generate correlation and regression models using the vital signs/physiological parameters for a clinical class of patients with respiratory failure and admitted to Intensive Care Unit (ICU). NEWS and RTS scores showed no significant correlation (r = 0.25, p<0.001) amongst themselves, however together NEWS and RTS showed significant correlation with Ps (blunt) (r = 0.70, p<0.001). RTS and Ps (blunt) scores showed some correlation (r = 0.63, p<0.001) and NEWS score showed significant correlation (r = 0.79, p<0.001) with Ps (blunt) scores. Furthermore, since individuals have to be monitored regardless of location, these kits have to have a built-in capability to locate the individual so that the incident response team can locate the individual based on Global Positioning System coordinates (GPS). A Quantum GIS (Geographical Information System) application using real-time GPS coordinates (OpenStreetMap coordinates) was used to calculate the shortest path using QGIS Network Analysis tool to demonstrate the calculation of shortest path and direction to locate the nearest service provider in shortest time. Along with locating the nearest healthcare service provider, it would help if the critical care team could be made aware of the physiological parameters and trauma scores using standard protocols accepted across the globe. The physiological parameters from the sensors along with the calculated trauma scores were encoded according to a standard Systematized Nomenclature of Medicine-Clinical Terms (SNOMED-CT) coding system and International Code of Diseases (ICD) codes and the trauma information was logged to Electronic Health Records (EHR) using Fast Health Interoperability Resources (FHIR) servers. FHIR servers provided interoperable web services to log the event information in real time. It could be concluded that analytical models trained on existing datasets can help in analyzing a traumatic experience or an injury and the information can be logged using a standard telemetry protocol as a telemedicine initiative. These scores enable the healthcare service providers to estimate the extent of trauma and prepare for medical emergency procedures and find applications in general and military healthcare.

As renewable energy generation prediction system has been introduced into the energy trading market, making a model to accurately predict the quantity of solar photovoltaic (PV) energy generation has become a significant problem. Moreover, to encourage an accurate prediction of the quantity of energy generation, an incentive system has been implemented for those who predict the quantity of solar PV energy under the error rate of 8%. Therefore, it has become more important to investigate and analyze current prediction technology numerically and develop more advanced prediction system. In this study, we tried to develop a better model to improve the accuracy of solar PV energy generation quantity by comparing three models made with gradient boosting machine (GBM), Model 1, Model 2, Model 3 respectively. Model 1 was built with the whole training data set without any additional preprocessing. After conducting some additional preprocessing procedure to predict solar energy generation more accurately, we made Model 2 with the whole training data set and Model 3 with only upper 10% of energy generation capacity. To compare the accuracy of three models, normalized mean absolute error (nMAE) was used as an evaluation index. The nMAE of Model 1 was 9.64% while the Model 2 showed 8.41%. Also, Model 3, which was constructed with the training set of upper 10% energy generation capacity, outperformed with the nMAE of 8.08%. For further study, to check the effectiveness of models constructed with GBM, a time series model, autoregressive integrated moving average (ARIMA), was also built and the nMAE was compared.

Following the coronavirus disease 2019 (COVID-19) pandemic, several studies have examined the possibility of correlating the virulence of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), the virus that causes COVID-19, to the climatic conditions of the involved sites; however, inconclusive results have been generally obtained. Although either air temperature or humidity cannot be independently correlated with virus viability, a strong relationship between SARS-CoV-2 virulence and the specific enthalpy of moist air appears to exist, as confirmed by extensive data analysis. Given this framework, the present study involves a detailed investigation based on the first 20–30 days of the epidemic before public health interventions in 30 selected Italian provinces with rather different climates, here assumed as being representative of what happened in the country from North to South, of the relationship between COVID-19 distributions and the climatic conditions recorded at each site before the pandemic outbreak. Accordingly, a correlating equation between the incidence rate of the pandemic and the average specific enthalpy of atmospheric air was developed, and an enthalpy-based seasonal virulence risk scale was proposed as a tool to predict the potential danger of COVID-19 spread due to the persistence of weather conditions favorable to SARS-CoV-2 viability. For practical applications, a conclusive risk chart expressed in terms of coupled temperatures and relative humidity (RH) values was provided, showing that safer conditions occur in case of higher RH at the highest temperatures, and of lower RH at the lowest temperatures. The proposed risk scale was in agreement with the available infectivity data in the literature for a number of cities around the world.

Predicting change from multivariate time series has relevant applications ranging from medical to engineering fields. Multisensory stimulation therapy in patients with dementia aims to change the patient’s behavioral state. For example, patients who exhibit a baseline of agitation may be paced to change their behavioral state to relaxed. This study aims to predict changes in behavioral state from the analysis of the physiological and neurovegetative parameters to support the therapist during the stimulation session. In order to extract valuable indicators for predicting changes, both handcrafted and learned features were evaluated and compared. The handcrafted features were defined starting from the CATCH22 feature collection, while the learned ones were extracted using a Temporal Convolutional Network, and the behavioral state was predicted through Bidirectional Long Short-Term Memory Auto-Encoder, operating jointly. From the comparison with the state-of-the-art, the learned features-based approach exhibits superior performance with accuracy rates of up to 99.42% with a time window of 70 seconds and up to 98.44% with a time window of 10 seconds.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (Cc) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, Cc was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e0). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate Cc such as Oedometer test. This study presents a novel prediction model for Cc of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate Cc based on LL, PL, and e0. The performance of developed GEP-based model was evaluated through coefficient of determination (R2), root mean squared error (RMSE), and mean average error (MAE). High R2 and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R2, RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining Cc of fine-grained soils.

The sustainability of the planet and its inhabitants is in dire danger and is among the highest priorities on global agendas such as the Sustainable Development Goals (SDGs) of the United Nations (UN). Solar energy -- among other clean, renewable, and sustainable energies -- is seen as essential for environmental, social, and economic sustainability. Predicting solar energy accurately is critical to increasing reliability and stability, and reducing the risks and costs of the energy systems and markets. Researchers have come a long way in developing cutting-edge solar energy forecasting methods. However, these methods are far from optimal in terms of their accuracies, generalizability, benchmarking, and other requirements. Particularly, no single method performs well across all climates and weathers due to the large variations in meteorological data. This paper proposes SENERGY (an acronym for Sustainable Energy), a novel deep learning-based auto-selective approach and tool that, instead of generalising a specific model for all climates, predicts the best performing deep learning model for GHI forecasting in terms of forecasting error. The approach is based on carefully devised deep learning methods and feature sets through an extensive analysis of deep learning forecasting and classification methods using ten meteorological datasets from three continents. We analyse the tool in great detail through a range of metrics and methods for performance analysis, visualization, and comparison of solar forecasting methods. SENERGY outperforms existing methods in all performance metrics including Root Mean Square Error (RMSE), Mean Absolute Error (MAE), Mean Absolute Percentage Error (MAPE), Forecast Skills (FS), Relative Forecasting Error, and the normalised versions of these metrics. The proposed auto-selective approach can be extended to other research problems such as wind energy forecasting and predict forecasting models based on different criteria (in addition to the minimum forecasting error used in this paper) such as the energy required or speed of model execution, different input features, different optimisations of the same models, or other user preferences.

This paper provides a review of an emerging field in the food processing sector, referring to efficient and safe food supply chains, ’from farm to fork’, as enabled by Artificial Intelligence (AI). Recent advances in machine and deep learning are used for effective food production, energy management and food labeling. Appropriate deep neural architectures are adopted and used for this purpose, including Fully Convolutional Networks, Long Short-Term Memories and Recurrent Neural Networks, Auto-Encoders and Attention mechanisms, Latent Variable extraction and clustering, as well as Domain Adaptation. Three experimental studies are presented, illustrating the ability of these AI methodologies to produce state-of-the-art performance in the whole food supply chain. In particular, these concern: (i) predicting plant growth and tomato yield in greenhouses, thus matching food production to market needs and reducing food waste or food unavailability; (ii) optimizing energy consumption across large networks of food retail refrigeration systems, through optimal selection of systems that can get shut-down and through prediction of the respective food de-freezing times, during peaks of power demand load; (iii) optical recognition and verification of food consumption expiry date in automatic inspection of retail packaged food, thus ensuring safety of food and people’s health.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (C_c) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, C_c was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e₀). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate C_c such as oedometer test. This study presents a novel prediction model for C_c of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate C_c based on LL, PL, and e₀. The performance of developed GEP-based model was evaluated through coefficient of determination (R²), root mean squared error (RMSE), and mean average error (MAE). High R² and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R², RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining C_c of fine-grained soils.Keywords: evolutionary model, gene-expression programming (GEP), prediction, soil compression index, estimation, soil engineering, soil informatics, civil engineering, machine learning, data science, big data, soft computing, deep learning, forecasting, subject classification codes, construction informatics, computational intelligence (CI), artificial intelligence (AI), estimation

This study advances the field of solar irradiance nowcasting by introducing a discrete-level classification approach, diverging from traditional continuous measurement methods. Grounded in a need for cost-effective and modular solutions, the research employs high-resolution computer vision coupled with a deep learning framework to predict Direct Normal Irradiance (DNI). By harnessing the capabilities of a Logitech C900 1080p HD camera and an NVIDIA Jetson module, the study achieves real-time data processing, pivotal for CSP systems' operational efficiency. The core of the methodology is the ResNet-50 convolutional neural network, refined via transfer learning on a bespoke dataset, culminating in a predictive accuracy of 85.78%. This discrete classification model contrasts with conventional, costly instruments like the MS-57, offering a novel and accessible alternative for DNI estimation. Such innovation not only demonstrates high predictive accuracy but also signifies a shift towards less resource-intensive and more adaptable solar energy forecasting tools, contributing a significant leap towards optimizing renewable energy systems.