Fluorinated compounds and co-enzymes are being widely researched and employed throughout research community because of their versatile physical, chemical and biological properties. In this work, we synthesized NiS-NiO/S-g-C3N4, a highly effective photocatalyst for C(sp3)-F bond activation and the regeneration of coenzyme (1,4-NADH) employing a new and ecologically acceptable route. The obtained photocatalyst exhibited important photocatalytic properties, such as good solar light harvesting ability, suitability of the optical band-gap, and facilitating efficient charge migrations. As a result, the newly designed NiS-NiO/S-g-C3N4 photocatalyst shows the excellent yield for regenerations of 1,4-NADH (51%). Further, a method of combining C(sp3)-F bond activation with photocatalysis has been demonstrated that represents a very powerful and sustainable approach, that can be a major breakthrough for the field of pharmaceutical.

The recent provision of energy-harvesting capabilities to wireless sensor networks has entailed the redefinition of design objectives. Specifically, the traditional goal of maximizing network lifetime has been replaced by optimizing network performance, namely delay and throughput. The present paper contributes to this reformulation by considering the routing problem for the class of time-driven energy-harvesting WSN (EH-WSN) under regular or quasi-periodic energy sources. In particular, this paper shows that the minimum hop count (MHC) criterion maximizes the average duty cycle that can be sustained by nodes in this type of scenarios. This is a primary objective in EH-WSN, since large duty cycles lead to enhanced performance. Based on a previous result, a general expression is first obtained which gives mathematical form to the relationship between duty cycle and traffic load for any node in a time-driven EH-WSN fed by a regular energy source. This expression reveals that the duty cycle achievable by a node decreases as its traffic load increases. Then, it is shown that MHC minimizes the average traffic load over the network, and thus it maximizes the average duty cycle of nodes. This result is numerically validated via simulation by comparison with other well-known routing strategies. Accordingly, this paper suggests assigning top priority to the MHC criterion in the development of routing protocols for time-driven EH-WSN under regular energy sources.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

Of all the renewable energy sources, solar photovoltaic (PV) power is estimated to be a popular source due to several advantages such as its free availability, absence of rotating parts, integration to building such as rooftops, and less maintenance cost. The nonlinear current-voltage (I–V) characteristics and power generated from a PV array primarily depend on solar insolation/irradiation and panel temperature. The extracted PV output power is influenced by the accuracy with which the nonlinear power–voltage (P–V) characteristic curve is traced by the maximum power point tracking (MPPT) controller. In this paper, a bio-inspired roach infestation optimization (RIO) algorithm is proposed to extract the maximum power from the PV system (PVS). To validate the usefulness of the RIO MPPT algorithm, MATLAB/Simulink simulations are performed under varying environmental conditions, for example, step changes in solar irradiance, and partial shading of the PV array. Furthermore, the search performance of the RIO algorithm is examined on different unconstrained benchmark functions, and it is that realized that the RIO algorithm has improved convergence characteristics in terms of finding the optimal solution than Particle swarm optimization (PSO). The results demonstrated that the RIO-based MPPT performs remarkably in tracking with high accuracy as the PSO-based MPPT.

This paper presents a microgrid distributed energy resources (DERs) for a rural standalone system. It is made up of solar photovoltaic (solar PV) system, battery energy storage system (BESS), and wind turbine coupled to permanent magnet synchronous generator (WT-PMSG). The DERs are controlled by maximum power point tracking (MPPT) based proportional intergral (PI) controllers for both maximum power tracking and error feedback compensation. The MPPT uses the perturb and observe (P&O) algorithm for tracking the maximum power point of the DERs. The PI gains are tuned using the Ziegler-Nichol’s method. The developed system was built and simulated in MATLAB/Simulink under two conditions - constant load, and step load changes. The controllers enabled the BESS to charge even during conditions of varying load and other environmental factors such as change of irradiance and wind speed. The reference was tracked very well by the output voltage of the DC grid. This is a useful research for electrifying the rural islanded areas, too far from the grid.

The world is in the grips of the COVID-19 pandemic. Public health measures that can reduce the risk of infection and death in addition to quarantines are desperately needed. This article reviews the roles of vitamin D in reducing risk of respiratory tract infections, knowledge about the epidemiology of influenza and COVID-19, and how vitamin D supplementation might be a useful measure to reduce risk. Through several mechanisms, vitamin D can reduce risk of infections. Those mechanisms include inducing cathelicidins and defensins that can lower viral replication rates and reducing concentrations of pro-inflammatory cytokines that produce the inflammation that injures the lining of the lungs, leading to pneumonia, as well as increase concentrations of anti-inflammatory cytokines. Several observational studies and clinical trials reported that vitamin D supplementation reduced risk of influenza, whereas others did not. Evidence supporting the role of vitamin D in reducing risk of COVID-19 includes that the outbreak occurred in winter, a time when 25-hydroxyvitamin D [25(OH)D] concentrations are lowest; that the number of cases in the Southern Hemisphere near the end of summer are low; that vitamin D deficiency has been found to contribute to acute respiratory distress syndrome, and that case-fatality rates increase with age and with chronic disease comorbidity, both of which are associated with lower 25(OH)D concentration. To reduce risk of infection, it is recommended that people at risk of influenza and/or COVID-19 consider taking 10,000 IU/d of vitamin D₃ for a few weeks to rapidly raise 25(OH)D concentrations, followed by 5000 IU/d. The goal should be to raise 25(OH)D concentrations above 40–60 ng/ml (100–150 nmol/l). For treatment of people who become infected with COVID-19, higher vitamin D₃ doses might be useful. Randomized controlled trials and large population studies should be conducted to evaluate these recommendations.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

Supermarkets in Port Harcourt (PH) city, Nigeria, predominantly rely on diesel electricity generation due to grid instability, leading to high cost of electricity prices. Although solar photovoltaic (PV) systems have been proposed as an alternative, these supermarkets have yet to adopt them, mainly due to high investment costs and a lack of awareness of the long-term financial and environmental benefits. This paper examines the technical and economic practicality of a PV system for these supermarkets using the PVsyst software and a spreadsheet model. Solar resources showed that PH has a daily average solar radiation and temperature of 4.21 kWh/m2/day and 25.73℃, respectively. Market Square, the supermarket with the highest peak power demand of 59.8 kW, and a 561 kWh/day load profile, was chosen as a case study. A proposed PV system with a power capacity of 232 kW, battery storage capacity of 34,021 Ah, a charge controller size of 100 A/560V, and an inverter with a power rating of 60V/75 kW has been designed to meet the load demand. The economic analysis showed a $266,936 life cycle cost, $0.12 per kWh levelized cost of electricity (LCOE), 4-year simple payback time, and a 20.5% internal rate of return (IRR). The PV system is feasible due to its positive net present value (NPV) of $165,322 and carbon savings of 582 tCO2/year.

The need to address climate change and establish sustainable urban environments has driven increased efforts in Europe to develop climate-neutral cities. This study highlights the importance of integrating solar energy technologies and nature-based solutions as key strategies to achieve climate neutrality. By examining current practices, emerging trends, and case examples, it explores the benefits, challenges, and prospects associated with the integration of solar energy and nature-based solutions in urban contexts. The study presents a pioneering approach to assess the urban heat and climate change mitigation benefits of combining building-integrated photovoltaics and nature-based solutions specifically within the European context. The results emphasize the synergistic relationship between nature-based components and solar conversion technology, identifying effective combinations for different climatic zones. In warmer regions of Southern Europe, strategies like rooftop photovoltaics on cool roofs, photovoltaics shadings, green walls, and urban trees have demonstrated effectiveness. Conversely, mid- and high-latitude European cities have seen positive impacts through the integration of rooftop photovoltaics and photovoltaics facades with green roofs and green spaces. As solar cell conversion efficiency improves, the environmental impact of photovoltaics is expected to decrease, facilitating their integration into urban environments. The study emphasizes the importance of incorporating water bodies, cool pavements, spaces with high sky-view factors, and effective planning in urban design to maximize resilience benefits. It also highlights the significance of prioritizing mitigation actions in low-income regions and engaging citizens in the development of social photovoltaics positive energy houses, resilient neighbourhoods, and green spaces. By adopting these recommendations, European cities can lead the way in creating climate-neutral urban environments that prioritize clean energy, nature-based solutions, and the overall well-being of residents. The findings underscore the need for a multidisciplinary approach that combines technological innovation, urban planning strategies, and policy frameworks to effectively achieve climate neutrality in European cities.

The diverse socio-economic and environmental impacts that the set-up of a new photovoltaic installation has must be weighed carefully in order to reach the best possible solution. Among the different photovoltaic systems there are several classification criteria, depending on the technology, application and the size of the modules that define them. The size (installed nominal capacity) stands out as an impartial and critical measure in the decision making process. In this article we use a multi-criteria decision making method to analyse the responses of five experts to a detailed questionnaire in which several different criteria are correlated with various photovoltaic installation sizes. The limitation associated to the low number of experts is addressed with a robustness and sensitivity analysis. With this study we seek first, to apply and demonstrate the feasibility of a methodology which combines technical information with multi-criteria decision making methods, and second, to obtain a clear result oriented that increases the benefits of a forthcoming photovoltaic installation of modules in distributed generation adding up to 1GW total peak power in standard conditions. We observe a consistent result in which smaller photovoltaic modules are the ideal solution that maximises the socio-economic benefits of any installation. If a decision has to be taken about the type of photovoltaic plant to be installed, the conclusion is clear: given a certain size, small, easily scalable installations are the best solution for stake-holders, for the inhabitants, and for the environment.

In this paper, the overall performance of Cu-(In,Ga)-Se₂ (CIGSe) solar cells was improved in the ultraviolet (UV)–visible wavelength region by two-segment process. In which, adjusting DC sputtering powers (20–40 W) for absorbers (segment I), and metal-alloy compositions (CdS, ZnO/CdS, ZnMgO/CdS and ZnMgO) for buffers (segment II) were explored and characterized. Upon choosing the optimal-30-W CIGSe-absorber (with 0.95-CGI ratio) sputtered by the segment-I process, the Cu-rich film can distinctly boost grain growth, thus reducing the trap state density. After segment-II process as the toxic-CdS alternative, the optimal Zn_0.9Mg_0.1O-alloy buffer can reach the best conversion efficiency (η = 8.70%) was attained for the environmental protection. Meanwhile, and the overall internal/external quantum efficiencies (IQE/EQE) were improved by 13.15%, respectively for the 2.48–3.62-eV bandgap (short wavelength) range. The developed photovoltaic (PV) module (with 9 optimum-CIGSe cells) exhibits acceptable stability with a variance within ±5% over the 60-day experiment. This discovery in PV-device research contributes to a new scientific understanding of renewable energy. Furthermore, this study undeniably enhances the progress of practical applications for PV-modules in alignment with sustainable development goals. It also actively supports the development of eco-friendly communities.

Addressing global environmental problem, water splitting to produce hydrogen fuel by solar energy is getting so much attention. In the water splitting, the essential problem to solve is the development of efficient　catalysts for oxygen production. In this paper, having the prospect for a practical application of photocatalysts to artificial photosynthesis, molecular mechanisms in the current literature are briefly reviewed. At first, recent progress in the function of Mn cluster at the natural photosystem II is briefly described. The kinds of devices in which oxygen evolution reaction (OER) catalysts are used were designated; water electrolyzers, photoelectrodes, and photocatalysts. Some methods for analyzing molecular mechanism in OER catalysis, emphasized by FTIR method, are shown briefly. After describing common OER mechanisms, the molecular mechanisms are discussed for TiO2 and BiVO4 photoelectrodes with our novel data, followed by presenting of co-catalysts IrO2, RuO2, NiO2, and other metal oxides for OER catalysts. Recent reports describing OER catalysts of perovskites, layered double hydroxides (LDH), metal-organic frameworks (MOF), single atom catalysts, as well as metal complexes are reviewed. Finally, by comparing with natural photosystem, the requiring factors to improve the activity of the catalysts for artificial photosynthesis will be discussed.

As renewable energy generation prediction system has been introduced into the energy trading market, making a model to accurately predict the quantity of solar photovoltaic (PV) energy generation has become a significant problem. Moreover, to encourage an accurate prediction of the quantity of energy generation, an incentive system has been implemented for those who predict the quantity of solar PV energy under the error rate of 8%. Therefore, it has become more important to investigate and analyze current prediction technology numerically and develop more advanced prediction system. In this study, we tried to develop a better model to improve the accuracy of solar PV energy generation quantity by comparing three models made with gradient boosting machine (GBM), Model 1, Model 2, Model 3 respectively. Model 1 was built with the whole training data set without any additional preprocessing. After conducting some additional preprocessing procedure to predict solar energy generation more accurately, we made Model 2 with the whole training data set and Model 3 with only upper 10% of energy generation capacity. To compare the accuracy of three models, normalized mean absolute error (nMAE) was used as an evaluation index. The nMAE of Model 1 was 9.64% while the Model 2 showed 8.41%. Also, Model 3, which was constructed with the training set of upper 10% energy generation capacity, outperformed with the nMAE of 8.08%. For further study, to check the effectiveness of models constructed with GBM, a time series model, autoregressive integrated moving average (ARIMA), was also built and the nMAE was compared.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .