This research illustrates modification of multi-walled carbon nanotubes (MWCNT) by ZrO2/Pb to construct nanocomposites (MWCNT/ZrO2/Pb-NCs) by simple precipitation technique and subsequently examine its ability for adsorption of Amido black (AB) and Eosin B (EB) dyes in binary system. The present nanocomposites investigation by FESEM, XRD, FTIR, and EDX analysis, reveal its as-synthesized crystalline nature with cubic morphology and average particle size 30–50 nm. The present nano-adsorbent represent high efficiency for AB and EB adsorption from aqueous solution, while dependency of variables including pH, initial concentration of dyes, contact time and MWCNT/ZrO2/Pb-NCs mass were analyzed by central composite design (CCD). The predicted maximum removal percentage was 95% removal for both dyes is consequence of adjustment of operational conditions at pH of 6.0; 0.05 g MWCNT/ZrO2/Pb-NCs; 15 min stirring at 15 mg L-1 for both dyes. The Langmuir as applicable for representation and description of reveal data of adsorption with adsorption capacity of 15.46 and 16.92 mg g-1 for AB and EB, respectively. Pseudo-first order model owing to its high correlation coefficient and closeness of experimental and theoretical data well represented behavior of corresponding adsorption system. Mechanism examination strongly proof high contribution of external mass transference as the main rate-controlling step. The successful regeneration of MWCNT/ZrO2/Pb-NCs suggested their usefulness in wastewater treatment and its ability of environmental management.

The food additive sorbic acid is considered as an effective preservative for certain cereal products, and propionic acid is commonly added in bakery wares, e.g. bread and fine bakery wares. The aim of this study is to develop and validate a new nuclear magnetic resonance spectroscopy (¹H NMR) method for routine screening and quantification of sorbic and propionic acids in bread and several bakery products for quality control purposes. Results showed that none of the screened samples contained higher concentrations than regulatory maximum limits. However, for some samples, labelling of preservatives was lacking or they were used in food categories, for which the use is not approved. It can be concluded that the developed NMR method can be used for routine screening of bakery products.

It is important to increase the quality of health and medicine. A wearable system for continuous monitoring of the patient is important to overcome this issue. Thus a patient with Arrhythmia due to its low cost and success in saving the life of the patient was the right option for the care partner. In addition, the device will provide a consumer with a smart smartphone application with accurate pulse beat and body temperature data in real time. MAX 30100 and LM35 are primarily used for the detection of human heart and temperature. The performance of these sensors is generated by an arrhythmia algorithm in the esp32 segment.

The color of a thin copper oxide layer formed on a copper plate was transformed from reddish-brown into blue-purple by irradiation with 5 keV Ar+ ions to a fluence as low as 1 1015 Ar+ cm–2. In the unirradiated copper oxide layer, the copper valence state of Cu2+ as well as Cu+ and/or Cu0 was included as indicated by the presence of a shake-up satellite line in a photoemission spectrum. While for the irradiated one, the satellite line decreased in intensity, indicating that irradiation resulted in the reduction from Cu2+ to Cu+ and/or Cu0. Furthermore, nuclear reaction analysis using a 16O(d, p)17O reaction with 0.85 MeV deuterons revealed a significant loss of oxygen (51015 O atoms cm–2) in the irradiated layer. Thus, the chromatic change observed in the present work originated in the irradiation-induced reduction of a copper oxide.

Pancreatic cancer is a fatal disease with mortality rate of 5% and a with a limited survival rate of 5 years. Despite of the extensive efforts that has been made to cure the disease it still has been considered as ‘undruggable’. It is characterized by epithelial to dense stromal tumor formation however due to lack of diagnosis options and treatment test available to detect the disease to the point at which resection of the tumor is possible, it makes it the fourth leading cause of cancer related death. The unavailable information regarding the early detection of biological markers along with the increased invasive tumor, the inherit chemoresistance against medication radiation and chemotherapy stubbornly fail the therapeutic options available. These associated problems made the scientists to reevaluate the approaches that are currently in practice and take a step back to fully understand the basic biological pathways that are involved in the pancreatic cancer, the heterogeneity of the tumor itself along with expression and a number of mutations that are observed at different locations. Clinical trial along with new approaches are nowadays focus of research to treat this tumor. The review paper describes the basic cellular pathways involved in pancreatic cancer, the gene mutations and their expression having effect on the pathology of the diseases along with treatment options that are available to treat the tumor. These efforts will help with the expansion of our knowledge to undergo the clinical trial and the synthesis of novel medicines for the prognosis of the disease.

The innovation of the new psychoactive substances (NPS) market requires the rapid identification of new substances that can be a risk to public health, in order to reduce the damage due to their use. Twelve seized products suspected to contain illicit substances were analyzed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gas chromatography coupled to mass spectrometry (GC-MS), and nuclear magnetic resonance spectroscopy (NMR). Synthetic cathinones (SCat) were found in all products, either as a single component or in mixtures. Infrared spectra of all products were consistent with the molecular structure of SCat, showing an intense absorption band at 1700–1674 cm‐1, corresponding to the carbonyl stretching, a medium/strong peak at 1605-1580 cm-1, indicating stretching vibrations in the aromatic ring (C=C) and bands with relative low intensity at frequencies near 2700–2400 cm-1, corresponding to an amine salt. It was possible to identify a total of eight cathinone derivatives by GC-MS and NMR analysis: 4’-methyl-α-pyrrolidinohexanophenone (MPHP), α-pyrrolidinohexanophenone (α-PHP), 3-fluoromethcathinone (3-FMC), methedrone, methylone, buphedrone, N-ethylcathinone, and pentedrone. Among the adulterants found in these samples, caffeine was the most frequently detected substance, followed by ethylphenidate. These results highlight the prevalence of SCat in seized materials of the Portuguese market. Reference standards are usually required for confirmation, but when reference materials are not available, the combination of complementary techniques is fundamental for a rapid and an unequivocal identification of such substances.

Red mud is a hazardous waste of alumina industry that contains high amounts of iron, aluminum, titanium and REEs. One of the promising methods for the extraction of iron from red mud is car-bothermic reduction with the addition of sodium salts. This research focuses on the process of hy-drochloric high-pressure acid leaching using 10–20% HCl of two samples of non-magnetic tailings obtained by 60-minute carbothermic roasting of red mud at 1300 °C and the mixture of 84.6 wt. % of red mud and 15.4 wt. % Na2SO4 at 1150 °C, respectively, with subsequent magnetic separation of metallic iron. An influence of temperature, leaching duration, solid-to-liquid-ratio and acid con-centration on dissolution behavior of Al, Ti, Mg, Ca, Si, Fe, Na, La, Ce, Pr, Nd, Sc, Zr were studied. Based on the investigation of the obtained residues, mechanism of passing of valuable elements into the solution was proposed. It has shown that 90% Al, 91% Sc and above 80% of other REEs can be dissolved under optimal conditions; Ti can be extracted into the solution or the residue depending on the leaching temperature and acid concentration. Based on the research results, novel flowsheets for red mud treatment were developed.

The conversion of CO2 into more synthetically flexible CO is an effective and potential method for CO2 remediation, utilization and carbon emission reduction. In this paper, the reaction of carbon-carbon dioxide (Boudouard reaction) was performed in a microwave fixed bed reactor using semi-coke (SC) as both the microwave absorber and reactant and was systematically compared with that heated in a conventional thermal field. The effects of the heating source, SC particle size, CO2 flow rate and additives on CO2 conversion and CO output were investigated. By microwave heating (MWH), CO2 conversion reached more than 99 %, while by conventional heating (CH), the maximum conversion of CO2 was approximately 29% at 900 °C. Meanwhile, for the reaction with 5 wt% Barium Carbonate added as a promoter, the reaction temperature was significantly reduced to 750 °C with almost quantitative conversion of CO2. Further kinetic calculations showed that the apparent activation energy of the reaction under microwave heating was 46.3 kJ/mol, which was only one-third of that observed under conventional heating. The microwave-assisted Boudouard reaction with catalytic barium carbonate is a promising method for carbon dioxide utilization.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

As a candidate for bifunctional asymmetric catalysts containing a half-sandwich C–N chelating Ir(III) framework (azairidacycle), a dinuclear Ir complex with an axially chiral linkage is newly designed. An expedient synthesis of chiral 2,2’-bis(aminomethyl)-1,1’-binaphthyl (1) from 1,1-bi-2-naphthol (BINOL) was accomplished by a three-step process involving nickel-catalyzed cyanation and subsequent reduction with Raney-Ni and KBH4. The reaction of (S)-1 with an equimolar amount of [IrCl2Cp*]2 (Cp* = 5-C5(CH3)5) in the presence of sodium acetate in acetonitrile at 80 °C gave a diastereomeric mixture of new dinuclear dichloridodiiridium (5) through the double C–H bond cleavage, as confirmed by 1H NMR spectroscopy. A loss of the central chirality on the Ir centers of 5 was demonstrated by treatment with KOC(CH3)3 to generate the corresponding 16e amidoiridium complex 6. The following hydrogen transfer from 2-propanol to 6 provided diastereomers of hydrido(amine)iridium with retaining the bis(azairidacycle) architecture. The dinuclear chlorido(amine)iridium 5 can serve as a catalyst precursor for the asymmetric transfer hydrogenation of acetophenone with a substrate to catalyst ratio of 200 in the presence of KOC(CH3)3 in 2-propanol, leading to (S)-1-phenylethanol with up to 67% ee.

The work focused on the development of high-temperature electrical insulation coatings for film photovoltaics. The idea was into replacing the electroconductive metal dispersed phase in siloxane high-temperature coating to ceramic particles with phonon thermal conductivity. The slurry of industrial composition based on polysiloxane lacquer and thermally conductive paste containing zinc oxide was centrifuged to obtain a thin, optically transparent coating with the destruction temperature of over 600 °C. Topology, electrical properties, and thermal conductivity of the resulting film were investigated. The mathematical model of thermal processes in films in the course of heating was figured out. Quantitatively the relation of thermal conductivities of a control sample and a sample with a heat-conducting filler was established. The effectiveness of using this technology is shown.

This paper presents an advanced microstructural analysis of the AlSiMg, Ti64 and N700 powders used for additive manufacturing. The internal microstructure of the regular and irregular powder grains were characterized down to atomic resolution by using scanning electron microscopy and high resolution scanning transmission electron microscopy.The accretionary forms on top of the irregular AlSiMg powder grains exhibit a slightly coarse microstructure with a network of eutectic Si consisting of nano-crystallites, suggestinga slower cooling than the grain itself that contain a predominately amorphous Si network. A nm thin amorphous C layer on the surface of some Ti64 plasma atomized powder grains promoted the attachment of satellites and growth of envelopes. In case of gas atomized N700 powder grains, we identified thin oxide and carbon amorphous layers as well as metal segregations at the interface between the grain body and the accretionary forms.

Synthesis of zeolite T with a variety of desired characteristics necessitate extensive work in the formulation and practical experiments either by conventional hydrothermal methods or aided with different approaches and synthesis techniques such as secondary growth or microwave irradiation. The objectives of this review are to adduce the potential work in zeolite T (Offretite-Erionite) synthesis evaluating determining factors affecting the synthesis and quality of the zeolite T crystals. Attention is given to the extensive studies that interconnect with other significant findings.

“Clickase” single-chain nanoparticles (Ck-SCNPs) are folded, enzyme-mimetic unimolecular polymeric nano-objects containing copper (Cu) ions able to catalyze the azide-alkyne Huisgen cycloaddition reaction in water and/or selected organic solvents, often in the presence of a reductant. Herein, we investigate the effect of morphology on catalytic activity of Ck-SCNPs synthesized by means of two different routes. An amphiphilic random copolymer composed of oligo(ethylene glycol) methyl ether methyl methacrylate (OEGMA) and 2-acetoacetoxy ethyl methacrylate (AEMA) units was used as precursor of these Ck-SCNPs. Folding was promoted through metal complexation between Cu(II) ions and beta-ketoester-containing AEMA moieties. The first route resulted in Ck-SCNPs1 containing Cu ions homogeneously distributed within each nanoparticle, whereas the second one promoted intra-chain clustering of Cu ions inside Ck-SCNPs2. A model fluorogenic “click” reaction between 9-(azidomethyl)anthracene and phenylacetylene, which was catalyzed either by Ck-SCNPs1 or Ck-SCNPs2, was used to unravel the effect of morphology on catalytic activity. This work paves the way to improve the catalytic activity of metallo-folded SCNPs through control of the intra-chain distribution of catalytic sites.

We report the synthesis and characterization of Poly Methyl-Meth-Acrylate (PMMA)/Poly vinylalcohol (PVA) polymeric blend doped with different concentrations of Copper oxide (CuO) nanoparticles (NPs). The (PMMA-PVA)/CuO nanocomposite hybrid thin films (wt. % = 0%, 2%, 4%, 8%, and 16%) of CuO NPs are deposited on glass substrates via dip-coating technique. The transmittance (T%), reflectance (R%), the absorption coefficient (α), the optical constants [refractive index (n), extinction coefficient (k)], optical dielectric functions [ɛ',ɛ''] are investigated and interpreted. Tauc, Urbach, Spitzer-Fan, and Drude models are employed to calculate the optical bandgap energy (Eg) and the optoelectronic parameters of the nanocomposite thin films. The refractive index and optical bandgap energy of of (PMMA-PVA) polymeric thin film are found to be (1.5 to 1.85) and 4.101 eV, respectively. Incorporation of specific concentrations of CuO-NPs in (PMMA-PVA) polymeric thin films leads to a noticeable decrease in the optical bandgap energy and to an increase of the refractive index. Moreover, Fourier Transform Infrared Spectroscopy (FTIR) transmittance spectra are measured and analyzed for undoped and doped polymeric thin films to pinpoint the major vibrational modes in the spectral range (500 and 4000 cm-1), as well as, the nature of network bonding in both systems. Thermal stability of thin films is investigated by performing thermogravimetric analysis (TGA). The TGA thermograms confirm that both doped polymeric thin films are thermally stable at temperatures below 110°C which enables them to be attractive for a wide range of optical and optoelectronic applications. Our results indicate that optical, vibrational and thermal properties of both polymeric thin films can be tuned for specific applications by the appropriate corporation of particular concentrations of CuO-NPs.

When the antioxidants in our immune system cannot neutralize or convert Reactive oxygen species into safe molecules at the rate at which it is produced then this imbalance is termed as “oxidative stress”. It is related with a wide array of diseases that includes cancer, diabetes, cardiovascular diseases, hypertension etc. These ROS species however are utmost essential for the proper functioning of human body which are produced as a consequence of partial oxidation of cellular metabolism performing essential functions such as protein phosphorylation, activation of several transcriptional factors, apoptosis, immunity, and differentiation. The sources by which these are produced can be broadly classified are intrinsic and extrinsic sources. There are variety of natural antioxidant enzymes of human body that combat against this oxidative stress. The extrinsic sources of ROS include the use of natural plants, extracted flavonoids and vitamins. In this review we will briefly explain how the sources of ROS, its essential function in human body, its elevation and associated damage to organs and effect on various diseases, and a hope of finding a way of how this oxidative stress can be exploited for therapeutic potential.

Hybrid scaffolds based on bioactive glass (BAG) particles (<38µm), covalently linked to the gelatin (G*), using 3-glycidoxypropyltrimethoxysilane (GPTMS), have been studied for bone bioengineering. In this study, two glass compositions (13-93 and 13-93B20 [where 20% of the SiO2 was replaced with B2O3]) were introduced in the gelatin matrix. The Cfactor (Gelatin/GPTMS molar ratio) was kept constant at 500. The hybrids obtained were found to be stable at 37°C, in solution; condition at which pure gelatin is liquid. All hybrids were characterized by in vitro dissolution in TRIS solution (for up to 4 weeks) and Simulated Body Fluid (SBF) (for up to 2 weeks). Samples processed with 13-93B20 exhibit a faster initial dissolution and significantly faster precipitation of a hydroxyapatite (HA) layer. The faster ion release and HA precipitation recorded from the G*/13-93B20 samples, is attributable to the higher reactivity of borosilicate compared to the silicate glass. MC3T3-E1 cells behavior, in direct contact with the hybrids, was investigated, showing that the cells were able to proliferate and spread on the developed biomaterials. Tailoring the glass composition allows to better control the material’s dissolution, biodegradability, and bioactivity. Bioactive (especially with 13-93B20 BAG), and biocompatible, the hybrids are promising for bone application.

One method of creating a brass coating is through electrodeposition, which is most often completed in cyanide galvanic baths. Because of the toxicity of cyanides, many are working on the development of cyanide-free baths, which are promising but not satisfactory to replace the classic methods. The purpose of the study was to explore a new generation of non-aqueous cyanide-free baths based on 1-ethyl-3-methylimidazolium acetate ionic liquids. The study involved the formation of copper, zinc, and brass coatings. The influence of the bath composition, cathodic current density, and temperature was determined. The obtained coatings were characterized by their morphology, chemical composition, roughness, and corrosion resistance. It was found that the structure of the obtained coatings is strongly dependent on the process parameters. The three main structures observed were fine-grained, porous, and olive-like. To the best knowledge of the authors, it is the first time the olive-like structure was observed in the case of an electrodeposited coating. The Cu-Zn coatings consisted of 19–96 at.% copper and exhibited relatively strong corrosion resistance. High improvement of corrosion properties was found in the case of copper and brass coatings with an olive-like structure.

A multilevel factorial design of 23 with 12 experiments was developed for the preparation of cellulose nanocrystals (CNC) from Agave tequilana Weber var. Azul bagasse. The studied parameters were acid type (H2SO4 and HCl), acid concentration (60 and 65 wt% for H2SO4, 2 and 8N for HCl) temperature (40 and 60°C for H2SO4, 50 and 90°C for HCl), and hydrolysis time (40, 55 and 70 min for H2SO4, 30, 115 and 200 min for HCl). The obtained CNC were physical and chemically characterized using dynamic light scattering (DLS), atomic force microscopy (AFM), Fourier-transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XDR) techniques. The size and morphology of A. tequilana CNC strongly depend on the acid type and hydrolysis parameters. The shortest CNC were obtained with H2SO4 (65 wt%, 40 °C, and 70 min) had a length of 137 ± 68 nm, width 33 ± 7 nm, and height 9.1 nm, whereas the shortest CNC obtained with HCl (2 N, 50 °C and 30 min) had a length of 216 ± 73 nm, width 69 ± 17 nm, and height 8.9 nm. CNC prepared from H2SO4 resulted shorter and thinner than those obtained with HCl. The total sulfate groups content in CNC obtained with H2SO4 increase with time agree to CSG=aebt, and increases with temperature and acid concentration.

A novel hybrid material based on Polyvinyl alcohol-Chitosan (PVA-Cs) was made, reinforced with conductive polymer fillers such as polypyrrole (PPy), Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS), carbon black (CB) and multi-wall carbon nanotubes (MW CNT). Our proposal is to use these fillers, which have not been studied in this context before, for obtaining composite materials, and to characterize them for the development of applications in microelectronics. FTIR analysis made evident the different func-tional groups present in the matrix and the fillers used. The use of quaternary mixtures (4 fillers) increased the contact angle, which increased the degree of hydrophobicity of the biocomposite. The Nyquist diagram of the analyzed samples showed a decrease in resistance and energy diffu-sion; the latter due to the transfer of electrons caused by the conductive polymers CB and the MWCNT. In the mechanical tension tests, Young's modulus values of 18.386 MPa were obtained, in contrast with the material matrix of PVA-Cs, which showed values of 11.628 MPa. Further-more, morphological analysis by SEM showed that the materials obtained were homogeneous, with no phase formation. The materials obtained showed higher electrical conductivity in the presence of the OH and NH2 groups, which could have possible applications in biopolymer elec-trodes.

Following the general aim of recapitulating the native mechanical properties of tissues and organs in vitro, the field of materials science and engineering has benefited from recent progress in developing compliant substrates with similar physical and chemical properties. In particular, in the field of mechanobiology, soft hydrogels can now reproduce the precise range of stiffnesses of healthy and pathological tissues to study the mechanisms behind cell response to mechanics. However, it was shown that biological tissues are not only elastic but also relax at different timescales. Cells can indeed perceive and actually need this dissipation because it is a critical signal integrated with other signals to define adhesion, spreading and even more complicated functions. The mechanical definition of hydrogels used in mechanobiology is however commonly limited to the elastic stiffness (Young’s modulus) and this value is known to depend greatly on the measurement conditions that are rarely reported. Here, we report that a simple relaxation test performed under well defined conditions can provide all the necessary information to characterize soft materials mechanically, by fitting the dissipation behavior with a generalized Maxwell model (GMM). The method was validated using soft polyacrylamide hydrogels and proved to be very useful to unveil precise mechanical properties of gels that cells can sense and offer a set of characteristic values that can be compared with what is typically reported from microindentation tests.

The paper describes the research findings on dynamic and mechanical properties of composite elastomers with high permeability magnetic filling agent capable of rapidly and reversibly changing its properties when exposed to an external magnetic field, which makes it a perspective material for application in a wide range of engineering areas. The research has analyzed the trends in the strength properties of the materials obtained through the use of filling agents of different fineness, content, and structural organization in the final polymer, under different conditions. This allowed to obtain the correlations between the influence of the filler's relative fineness on the dynamic and mechanical properties of composite polymers, and to estimate the trends in the parameters describing the material strength under the complex magnetic and thermal influence. The results obtained by the authors allowed to ground the composition and structural organization of the final material with the best set of dynamic and mechanical properties.

Nano medicine seeks to deliver a valuable set of research tools and clinically useful devices in the near future. The current medical field is in dire need of new commercial applications in the pharmaceutical industry that may include advanced drug delivery systems, new therapies, and in vivo imaging. Here in this experimental study, the nano materials used in DNA biosensors like silver nano dots were incorporated as nano biosensors are used for both therapeutic and diagnostic applications. The most important step while preparing a DNA biosensor is the immobilization of DNA probe on the surface of a sensing device such as an electrode. The amount of immobilized DNA probe will influence the accuracy sensitivity, selectivity and life of a DNA biosensor directly. Because of the high surface to volume ratio and excellent biological compatibility, nano materials can enlarge the sensing surface area to increase the amount of immobilized DNA and the DNA mixed with nano materials can keep its biologically activity well.In this study,silver nano dots created in our lab were functionalized with thio nucleides and were used as nano sensor probes in bio bar code assays.

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

Directed Energy Deposition (DED) is a process that enables high-speed deposition with a sub-millimeter thickness using laser technology. Thus far, defect studies on additive manufacturing, including DED, have focused mostly on preventing pores and crack defects that reduce fatigue strength. On the other hand, evaporation products, fumes and spatters, generated by the high energy have often been neglected despite being some of the main causes of porosity and defects. In high-quality metal deposition, the problems caused by evaporation products are difficult to solve, but they have not yet caught the attention of metallurgists and physicists. This review examines the effect of the laser, material, and process parameters on the evaporation products to help obtain a high-quality metal film layer in thin-DED.

Abstract: As a low-input crop, Miscanthus offers numerous advantages that, in addition to agricultural applications, permits its exploitation for energy, fuel, and material production. Depending on the Miscanthus genotype, season, and harvest time as well as plant component (leaf versus stem), correlations between structure and properties of the corresponding isolated lignins differ. Here, a comparative study is presented between lignins isolated from M. x giganteus, M. sinensis, M. robustus and M. nagara using a catalyst-free organosolv pulping process. The lignins from different plant constituents are also compared regarding their similarities and differences regarding monolignol ratio and important linkages. Results showed that the plant genotype has the weakest influence on monolignol content and interunit linkages. In contrast, structural differences are more significant among lignins of different harvest time and/or season. Analyses were performed using fast and simple methods such as nuclear magnetic resonance (NMR) spectroscopy. Data was assigned to four different linkages (A: b-O-4 linkage, B: phenylcoumaran, C: resinol, D: b-unsaturated ester). In conclusion, A content is particularly high in leaf-derived lignins at just under 70 % and significantly lower in stem and mixture lignins at around 60 % and almost 65 %. The second most common linkage pattern is D in all isolated lignins, the proportion of which is also strongly dependent on the crop portion. Both stem and mixture lignins, have a relatively high share of approximately 20 % or more (maximum is M. sinensis Sin2 with over 30 %). In the leaf-derived lignins, the proportions are significantly lower on average. Stem samples should be chosen if the highest possible lignin content is desired, specifically from the M. x giganteus genotype, which revealed lignin contents up to 27 %. Due to the better frost resistance and higher stem stability, M. nagara offers some advantages compared to M. x giganteus. Miscanthus crops are shown to be very attractive lignocellulose feedstock (LCF) for second generation biorefineries and lignin generation in Europe.

FeIFeI Fe2(S2C3H6)(CO)6(µ-CO) (1a-CO) and its FeIFeII cationic species (2a+-CO) are the simplest model of the CO-inhibited [FeFe] hydrogenase active site, which is known to undergo CO photolysis within a temperature- dependent process whose products and mechanism are still a matter of debate. Using Density Functional Theory (DFT) and Time-Dependent Density Functional Theory (TDDFT) computations, the ground state and low-lying excited state potential energy surfaces (PESs) of 1a-CO and 2a+-CO have been explored aimed at elucidating the dynamics of the CO photolysis yielding Fe2(S2C3H6)(CO)6 (1a) and Fe2(S2C3H6)(CO)6+ (2a+), two simple models of the catalytic site of the enzyme. Two main results came out from these investigations. First, a-CO and 2a+-CO are both bound with respect to any CO dissociation with lowest free energy barriers around 10 kcal mol-1, suggesting that at least 2a+-CO might be synthetized. Second, focusing on the cationic form, we found at least two clear excited state channels along the PESs of 2a+-CO that are unbound with respect to equatorial CO dissociation.

(1) Background: Bacterial reinfection and root fracture are the main culprits related to root canal treatment failure. This study aimed to assess the utility of quercetin solution as an adjunctive endodontic irrigant that strengthen root canal dentin with commitment anti-biofilm activity and bio-safety. (2) Methods: Based on a noninvasive dentin infection model, dentin tubules infected with Enterococcus faecalis (E. faecalis) were irrigated with sterile water (control group), and 0, 1, 2, 4 wt% quercetin-containing ethanol solutions. The live and dead bacteria proportions within E. fae-calis biofilms were analyzed using confocal laser scanning microscopy (CLSM). Elastic modulus and hydroxyproline release and X-ray photoelectron spectroscopy (XPS) characterization was tested on irrigant-treated demineralized dentin to evaluate irrigants’ biostability. The cytotoxicity of irrigants was tested by CCK-8 assay. (3) Results: Quercetin increased the proportion of dead bacteria volumes within E. faecalis, and improved the flexural strength of dentin collagen com-pared to control group. The XPS characterization revealed an increase in C-O peak area under both C1s and O1s narrow-scan spectra. The CCK-8 assay confirmed no cytotoxicity of quercetin solutions. (4) Conclusions: Quercetin exhibited anti-biofilm activity, collagen-stabilizing effect as well as cytocompatibility, supporting quercetin as a potential candidate for endodontic irrigant.

This article discusses the issue of hardened steel machining. Many components in the engineering industry use hardening as the final heat treatment. These components usually occupy a significant position in a given assembly unit. They guarantee the correct operation of the entire technical equipment in total cooperation with other components. The quality of these components depends on the integrity of their surface. The production of these parts is usually carried out by traditional technological procedures. An example of such a technology is clearly grinding. However, this article discusses the application of other finishing technologies using tool material made of cubic boron nitride (CBN). The technology used is finishing turning with subsequent tumbling technology. The subject of the evaluation is the integrity of the surface. In this part of the experiments, there are mainly individual parameters of surface roughness. Compared components are bearing rings, in this case the inner surface of the housing ring.

Ti6Al4V samples obtained by selective laser melting were subjected to acid treatment, chemical oxidation in hydrogen peroxide solution and subsequent thermochemical treatment. The effect of temperature and time of acid etching of Ti6Al4V samples on surface roughness, morphology, topography and chemical and phase composition after the thermochemical treatment was studied. The surfaces were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and contact profilometry. Pore and protrusion sizes were measured. Acid etching modified the elemental composition and surface roughness of the alloy. Temperature had a greater influence on the morphology, topography and surface roughness of samples than time. Increases in roughness values were observed when applying successive chemical oxidation and thermochemical treatment compared to the values observed on surfaces with acid etching. After the thermochemical treatment, the samples with acid etching at a temperature of 80 °C showed a multiscale topography. In addition, a network-shaped structure was obtained on all surfaces, both on their protrusions and pores previously formed during the acid etching.

One-step reactive melt processing (REx) via radical reaction was evaluated with the aim of improving the rheological properties of poly(ε-caprolactone) (PCL). In particular, a water-assisted REx was designed under the hypothesis of increasing crosslinking efficiency with water as a low viscous medium in comparison with a slower PCL macroradicals diffusion in the melt state. To assess the effect of dry vs. water-assisted REx on PCL, its structural, thermo-mechanical and rheological properties were investigated. Water-assisted REx resulted in increased PCL gel fraction compared to dry REx (from 1 to 34 %), proving the rationale under the formulated hypothesis. From dynamic mechanical analysis and tensile tests, the crosslink did not significantly affect the PCL mechanical performance. Dynamic rheological measurements showed that higher PCL viscosity was reached with increasing branching/crosslinking and the typical PCL Newtonian behavior was shifting towards a progressively more pronounced shear thinning. A complete transition from viscous- to solid-like PCL melt behavior was recorded, demonstrating that higher melt elasticity can be obtained as a function of gel content by controlled REx. Improvement in rheological properties offers the possibility of broadening PCL melt processability without hindering its recycling by melt processing.

Long-chain branched metallocene-catalyzed high-density polyethylenes (LCB-mHDPE) were solution blended to obtain blends with varying degrees of branching. A high molecular LCB-mHDPE was mixed with low molecular LCB-mHDPE are varying concentrations, whose rheological behavior is similar but whose molar mass and molar mass distribution is significantly different. Those blends were characterized rheologically to study the effects of concentration, molar mass distribution, and long-chain branching level of the low molecular LCB-mHDPE. Owing to the ultra-long relaxation times of the high molecular LCB-mHDPE, the blends started behaving clearly more long-chain branched than the base materials. The thermorheological complexity showed an apparent increase in the activation energies Ea determined from G’, G”, and especially δ. Ea(δ), which for LCB-mHDPE is a peak function, turned out to produce even more pronounced peaks than observed for regular LCB-mPE and also LCB-mPE with broader molar mass distribution. Thus, it is possible to estimate the molar mass distribution from the details of the thermorheological complexity.

We investigated the properties of architected materials made from UV-cured urethane elastomers and the use of such materials for insoles. The durability and reliability of various materials currently used in medical insoles were compared with those of architected materials with microlattice. The results show that architected materials made from UV-cured urethane elastomers have high impact resilience and grip, and the hardness can easily be changed by adjusting the column diameter of the unit cell. Compared with the foam materials used for medical insoles today, these architected materials also demonstrate superior UV resistance, suggesting that, after being washed in water, they can be air-dried outdoors.

Glycosphingolipids (GSL) represent a highly heterogeneous class of lipids with many cellular functions, implicated in a wide spectrum of human diseases. Their isolation, detection, and comprehensive structural analysis is a challenging task due to the structural diversity of GSL molecules. In this work, GSL subclasses are isolated from human plasma using an optimized monophasic ethanol–water solvent system capable to recover a broad range of GSL species. Obtained deproteinized plasma is subsequently purified and concentrated by C18-based solid-phase extraction (SPE). The hydrophilic interaction liquid chromatography (HILIC) coupled to electrospray ionization linear ion trap tandem mass spectrometry (ESI-LIT-MS/MS) is used for GSL analysis in the human plasma extract. Our results provide an in-depth profiling and structural characterization of glycosphingolipid and some phospholipid subclasses identified in the human plasma based on their retention times and the interpretation of tandem mass spectra. The structural composition of particular lipid species is readily characterized based on the detailed interpretation of MS and MS/MS spectra and further confirmed by specific fragmentation behavior following predictable patterns, which yields to the unambiguous identification of 154 GSL species within 7 lipid subclasses and 77 phospholipids representing the highest number of GSL species ever reported in the human plasma. The developed HILIC-ESI-MS/MS method can be used for further clinical and biological research of GSL in the human blood or other biological samples.

Biofilms play a crucial role in the development of Candida-associated denture stomatitis. Inhibition of microbial adhesion to PMMA and phosphate containing PMMA has been examined in this work. C. albicans and mixed salivary microbial biofilms were compared on naked and salivary pre-conditioned PMMA surfaces in the presence or absence of antimicrobials (cetyl pyridinium chloride [CPC], KSL-W, histatin 5 [his 5]). Polymers with varying amounts of phosphate (0-25%) were tested using four C. albicans oral isolates as well as mixed salivary bacteria and 24 h biofilms were assessed for metabolic activity and confirmed using Live/Dead staining and confocal microscopy. Biofilm metabolism was reduced as phosphate density increased (15%: P=0.004; 25%: P=0.001). Loading of CPC on 15% phosphated disks showed a substantial decrease (P=0.001) in biofilm metabolism in the presence or absence of a salivary pellicle. Salivary pellicle on uncharged PMMA enhanced the antimicrobial activity of CPC only. CPC also demonstrated remarkable antimicrobial activity on mixed salivary bacterial biofilms under different conditions displaying the potent efficacy of CPC (350 µg/ml) when combined with an artificial protein pellicle (Biotene half strength).

In this work, kinetics of the reaction between 5,10,15,20-tetrakis(N-methylpyridium-4-yl)porphyrin and Ni2+ species were investigated in aqueous solution at 25 ±1 ºC in I = 0.10 M (NaNO3). Speciation of Ni2+ was carried out in I = 0.10 M (NaNO3) in order to provide the distribution of the Ni2+ species with different solution pH. The experimental data have been compared with the speciation diagram constructed from the values of hydrolysis constants of Ni2+ ion. Speciation data showed that the hexaaquanickel(II), [Ni(H2O)6]2+, ions take place in hydrolysis reactions through formation of [Ni(OH2)6-n(OH)n]2-n species with solution pH. Based on the speciation of Ni2+ and pH dependent rate constants, rate expression can be written as: d[Ni(TMPyP)4+]/dt = (k1[Ni2+(aq)] + k2[Ni(OH)+(aq)] + k3[Ni(OH)2o(aq)] + k4[Ni(OH)3-(aq)])[H2TMPyP4+], where k1, k2, k3 and k4 were found to be k1 = (0.62 ± 0.22) × 10-2; k2 = (3.60 ± 0.40) × 10-2; k3 = (2.09 ± 0.52) × 10-2, k4 = (0.53 ± 0.04) × 10-2 M-1s-1 at 25 ±1 °C, respectively. Kinetic results showed that monohydroxo, [Ni(H2O)5(OH)]+, is the most reactive among the [Ni(OH2)6-n(OH)n]2-n species. The enhanced reactivity has been ascribed to the formation of hydrogen bonding between oxygen atom of hydroxyl group of the [Ni(H2O)5(OH)]+ species and the pyrrolic hydrogen atom of the [H2TMPyP]4+. The rate of formation of [Ni(II)TMPyP]4+ complex was to be 3.99 × 10-2 M-1s-1 in I = 0.10 M, NaNO3 (25 ± 1 ºC). Ionic strength effect on the reaction rate is suggested that the net charge of the tetracationic porphyrin is to be +3.6 on the basis of Brønsted-Bjerrum equation. The UV-Vis and fluorescence data revealed that [Ni(II)TMPyP]4+ and H2(TMPyP)4+ interact with DNA, and UV-Vis results suggest that Ni(II)-porphyrin and free base porphyrin interact with DNA via outside binding with self-stacking and intercalation, respectively. Mechanism of kinetics of formation of the [Ni(II)TMPyP]4+ complex in aqueous medium is discussed. An investigation of application of the [Ni(II)TMPyP]4+ complex along with other metalloporphyrins such as Zn2+-, Ru2+-, Pt2+-, [Au(III)TMPyP]5+ as anti-COVID-19 agents is now in progress under international collaboration.

We present new results in positron annihilation lifetime spectroscopy (PALS), thermo-optical dilatometry and microscopy, which are indicating a strong correlation between grain-boundaries and mass transport during the sintering process of carbonyl iron powder. In this particular system we were able to show that the change in particle shape and size with increasing temperature yields an anisotropy in shrinkage, which manifests itself in a higher shrinkage perpendicular to the compaction axis. In the intermediate stage of sintering, where the major mass transport occurs, the average distance between two grain boundaries could be determined to (3,73 ± 0,18) μm at T = 744°C. This is in good agreement with previous calculations of positron pathways in defect free particles. Furthermore, due to sintering temperatures far above the annealing temperature of dislocations in iron, the existence of dislocations in the bulk of the particles is very unlikely. These claims are reflected by the collected positron data, which exhibit a clear grain boundary signal of ∼ 250ps while no vacancy or dislocation signal (typically ∼ 160 ps) is evident in the intermediate stage of sintering.

Focused electron beam induced deposition is a versatile tool for the direct fabrication of complex-shaped nanostructures with unprecedented shape fidelity and resolution. While the technique is well-established for various materials, the direct electron beam writing of silver is still in its infancy. Here, five different silver carboxylates, three fluorinated: [Ag2(µ-O2CCF3)2], [Ag2(µ-O2CC2F5)2], [Ag2(µ-O2CC3F7)2] and two containing hydrogen: [Ag2(µ-O2CCMe2Et)2] and [Ag2(µ-O2CtBu)2] were examined and compared as potential precursors for focused electron beam induced deposition. All of the compounds show high sensitivity to electron dissociation and efficient dissociation of Ag-O bonds. The as-deposited materials showed high silver content from 42 at.% to above 70at.% and silver nano-crystal formation with impurities of carbon and fluorine incorporated between metal grains. A correlation of the number of carbon atoms in the precursor ligands and silver content of the deposited structures was found. The highest silver contents were achieved for compounds with the shortest CF chains. The deposited silver content depends on the balance of electron induced ligand co-deposition and thermal ligand desorption. Low electron flux is advantageous for high silver content. Our findings demonstrate that silver carboxylates constitute a promising group of precursors for focused electron beam nanoprinting of high silver content materials.

89Zr-radiolabelled proteins functionalised with desferrioxamine B are a cornerstone of diagnostic positron emission tomography. In the clinical setting, 89Zr-labelled proteins are produced manually. Here, we explore the potential of using a microfluidic photochemical flow reactor to prepare 89Zr-radiolabelled proteins. The light-induced functionalisation and 89Zr-radiolabelling of human serum albumin ([89Zr]ZrDFO-PEG3-Et-azepin-HSA) was achieved by flow photochemistry with a decay-corrected radiochemical yield (RCY) of 31.2±1.3% (n = 3) and radiochemical purity &gt;90%. In comparison, a manual batch photoreactor synthesis produced the same radiotracer in a decay-corrected RCY of 59.6±3.6% (n = 3) with an equivalent RCP &gt;90%. The results indicate that photoradiolabelling in flow is a feasible platform for the automated production of protein-based 89Zr-radiotracers, but further refinement of the apparatus, and optimisation of the method is required before the flow process is competitive with manual reactions.

Self-assembling peptide P11-4 is amphiphilic and pH-triggered with demonstrated effectivity repairing early carious lesions in enamel. However, P11-4 effects on dentin biomineralization and repair remain unexplored. Thus, cytocompatibility and effectiveness of P11-4 inducing mineralization and migration of odontoblast-like cells (MDPC-23) were investigated. MDPC-23 were seeded in contact with P11-4(0.5µg/ml and 1µg/ml), Dentin Matrix Protein 1 (DMP1 0.5µg/ml and 1 µg/ml) or Calcium hydroxide (Ca(OH)2 100µg/ml) solutions. Cytotoxicity was verified using MTT (n=6/group). Mineralization was tested using Alizarin Red (n=4/group). Cell migration was assessed by light microscopy (n=2/group). MTT and Alizarin Red data were compared using Krus-kal-Wallis and Mann-Whitney (α=0.05). P11-4 (0.5µg/ml and 1µg/ml) and DMP1 (0.5µg/ml and 1µg/ml) presented the highest cytocompatibility; Ca(OH)2 presented the lowest. DMP1 1µg/ml exhibited the highest mineralization ability, with no difference to P11-4 1µg/ml. Ca(OH)2 presented lower values than DMP1 1µg/ml (p<0.05), but similar to P11-4 1µg/ml. P11-4 and DMP1 at 0.5 µg/ml showed induced less mineralization than P11-4 and DMP1 at 1µg/ml (p<0.05), with no difference to Ca(OH)2. All materials stimulated cell migration, however, lower concentrations of DMP1 and P11-4 provided better results. P11-4 is cytocompatible, induces mineralization and MDPC-23 migration like DMP1. P11-4 could be an alternative for dentin mineralization and tooth repair.

A gold nanostructured film modified glassy carbon electrode (Au_film/GCE) was developed for the determination of chromium (VI) in water sample. GCE was immersed into HAuCl₄ solution (10^-3M) and electrodeposition of thin gold layer was conducted at –0.4 V (vs Ag/AgCl) for 10 min. The strong affinity between Au and Cr species resulted with increasing of Cr (VI) signal, compared with the bare glassy carbon electrode. The electrodepositing time, type of supporting electrolyte, pH, the scan rate, modulation amplitude, and modulation time were optimized using differential pulse anodic stripping voltammetry (DP-ASV). The calibration graph using accumulation time of 120 s was linear from 10 to 120 µgL^-1 with a sensitivity 1.3 x 10^-2 µA/µgL^-1. Under optimum experimental conditions, a good correlation coefficient R²=0.9971, and a low detection limit 5.5 µg/L Cr (VI) was obtained. The signal was reproducible with a relative standard deviation ±4.5 %. The developed Au_film/GCE sensor was applied for the Cr (VI) determination of in sewage water samples.

In spite of unique structural, spectroscopic and redox properties, the synthetic variants of the planar, antiaromatic hexaphyrin (1.0.1.0.1.0) derivatives 2, has been limited due to the low yields and difficulty in access to the starting material. A chemical modification of the meso-substituents could be good alternative overcoming the synthetic barrier. Herein, we report a regio-selective nucleophilic aromatic substitution (SNAr) of meso-pentafluorophenyl group in rosarrin 2 with catechol. The reaction afforded benzodioxane fused rosarrin 3 as single product with high yield. The intrinsic antiaromatic character of the starting rosarrin 2 retained throughout the reactions. Clean, two electron reduction was achieved by treatment of 3 with SnCl2•2H2O affording 26pi-electron aromatic rosarrin 4. The synthesized compounds exhibited noticeable changes in photophysical and redox properties compared with starting rosarrin 2. .

Classical k-ratio models, e.g. ZAF and phi(rho z), used in electron probe microanalysis (EPMA) assume a homogeneous or multi-layered material structure, which essentially limits the spatial resolution of EPMA to the size of the interaction volume where characteristic x-rays are produced. We present a new model for characteristic x-ray emission that avoids assumptions on the material structure to not restrict the resolution of EPMA a-priori. Our model bases on the spherical harmonic (PN) approximation of the Boltzmann equation for electron transport in continuous slowing down approximation. PN models have a simple structure, are hierarchical in accuracy and well-suited for efficient adjoint-based gradient computation, which makes our model a promising alternative to classical models in terms of improving the resolution of EPMA in the future. We present results of various test cases including a comparison of the PN model to a minimum entropy moment model as well as Monte-Carlo (MC) trajectory sampling, a comparison of PN-based k-ratios to k-ratios obtained with MC, a comparison with experimental data of electron backscattering yields as well as a comparison of PN and Monte-Carlo based on characteristic X-ray generation in a three-dimensional material probe with fine structures.

The aims of this work were to examine the new electrode, based on polymer bacteria modified aluminum electrode for simultaneous production of electricity and degradation of phenol. This electrode is based aluminum modified by bacteria inserted in the polymer matrix, developed in situ on the surface. This electrode, designated subsequently by bacteria-polymer-aluminum, Showed stable response and was characterized with voltametric methods, as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The experimental results revealed that the prepared electrode could be a feasible for degradation of hazardous phenol pollutants. The sensor was successfully applied to the determination of phenol in a real sample with satisfactory results.

The wide interest in developing green energy technologies stimulates the scientific community to seek, for devices, new substitute material platforms with low environmental impact, ease of production and processing and long-term stability. The synthesis of metal oxide (MO) semiconductors fulfils these requirements and efforts are addressed at optimizing their functional properties, through improvement of charge mobility or energy level alignment. Two MOs have rising perspectives for application in light harvesting devices, mainly for the role of charge selective layers but also as light absorbers, namely MoO3 (an electron blocking layer) and Co3O4 (a small band gap semiconductor). The need to achieve better charge transport has prompted us to attempt doping strategies with vanadium (V) ions that, when combined with oxygen in V2O5, produce a high work function MO. We report on subcritical hydrothermal synthesis of V-doped mesostructures of MoO3 and of Co3O4, in which a tight control of the doping is exerted by tuning the relative amounts of reactants. We accomplished a full analytical characterization of these V-doped MOs that unambiguously demonstrates incorporation of the vanadium ions in the MO crystal lattice, as well as effects on the optical properties and work function. We foresee a promising future use of these materials as charge selective materials in energy devices based on multilayer structures.

The excellent properties of nanomaterials have been confirmed in many fields, but the effects on plants are still unclear. In this study, we have found that bismuth vanadium promoted the growth of taproots and the development of lateral roots, increased the roots activity by regulating the expression of polyamine or hormone-related genes and reducing the accumulation of reactive oxygen species in Arabisdopsis thaliana. Meantime, BV had higher antimicrobial effect than that of graphene oxide (GO). These results showed us a new perspective possibility of nanomaterials assisting the development of plants and crops, which is expected to become one of the ways to solve the problem of controlling and promoting the development of plants and crops.

With the aim of profitable conversion of carbon dioxide (CO2) in an efficient, economical and sustainable manner, we developed a CuBr/ionic liquid (1-butyl-3-methylimidazolium acetate) catalytic system which could efficiently catalyze the three-component reactions of propargylic alcohols, 2-aminoethanols, and CO2 to produce 2-oxazolidinones and α-hydroxy ketones. Remarkably, this catalytic system employed lower metal loading (0.0125-0.5 mol%) but exhibited the highest turnover number (2960) ever reported, demonstrating its excellent activity and sustainability. Moreover, our catalytic system could efficiently work under 1 atm of CO2 pressure and recycle among the metal-catalyzed systems.

The paper presents attribute based characterization of nanomaterials method for computer storage and retrieval as knowledgebase. The knowledgebase permits indepth understanding and comparison between nanomaterials available with the scientists and product developers to satisfy their research and development (R & D) needs. Techniques for order preference by similarity to ideal solution (TOPSIS) is proposed to evaluate nanomaterials in the presence of multiple attributes. The method normalizes attributes to nullify the effect of different units and their values in the range of 0 to 1. The relative importance of different attributes for different applications is considered. The weight vector is derived using Eigen value formulation. The positive and negative benchmark solutions are derived. Euclidean distance of alternatives from these best and worst solution leads to the development of proximity /goodness/suitability index for ranking. Final decision is taken by decision makers by SWOT analysis and short and long term strategies of the organisation. The methodology is illustrated with the help of an example and step-by-step procedure. Results, discussion and conclusion highlights the importance and practical application.

Therapeutic options for the highly pathogenic human Severe Acute Respiratory Syndrome-Coronavirus 2 (SARS-CoV-2) causing the current pandemic Coronavirus disease (COVID-19) are urgently needed. COVID-19 is associated with viral pneumonia and acute respiratory distress syndrome causing significant morbidity and mortality. The proposed treatments for COVID-19, such as hydroxychloroquine, remdesivir and lopinavir/ritonavir, have shown little or no effect in the clinic. Additionally, bacterial and fungal pathogens contribute to the SARS-CoV-2 mediated pneumonia disease complex. The antibiotic resistance in pneumonia treatment is increasing at an alarming rate. Therefore, carbon-based nanomaterials (CBNs), such as fullerene, carbon dots, graphene, and their derivatives constitute a promising alternative due to their wide-spectrum antimicrobial activity, biocompatibility, biodegradability and capacity to induce tissue regeneration. Furthermore, the antimicrobial mode of action is mainly physical (e.g. membrane distortion), which is characterized by a low risk of antimicrobial resistance. In this review, we evaluated the literature on the antiviral activity and broad-spectrum antimicrobial properties of CBNs. CBNs had antiviral activity against 12 enveloped positive-sense single-stranded RNA viruses similar to SARS-CoV-2. CBNs with low or no toxicity to the humans are promising therapeutics against COVID-19 pneumonia complex with other viruses, bacteria and fungi, including those that are multidrug-resistant.

This work investigates the influence of strain rate on the stress/strain behaviour of Scalmalloy. This material is an aluminium-scandium-magnesium alloy, specifically developed for additive manufacturing. The bulk yield stress of the material processed by Selective Laser Melting is approximately 340 MPa which can be increased by heat-treating to approximately 530 MPa. These numbers, combined with the low mass density of 2.7 g/cm3, make Scalmalloy an interesting candidate for lightweight crash-absorbing structures. As this application is inherently dynamic, it is of interest to study the loading rate sensitivity, which is difficult to predict: Al-Sc alloys exhibit classic strain rate sensitivity with an increased yield stress at elevated strain rates. However, Al-Mg alloys are known to show the contrary effect, they exhibit less strength as strain rate is increased. To answer the question how these effects combine, we study the dynamic behaviour at four different strain rates ranging from 10−3 /s to 1000 /s using servo-hydraulic and Split-Hopkinson testing methods. The resulting data is analysed in terms of strain rate sensitivity of tensile strength and failure strain. A constitutive model based on a simplified Johnson-Cook approach is employed to simulate the tensile tests and provides good agreement with the experimental observations.

Finding new ways for the preparation of cross-linked structures is a significant problem in terms of materials for biomedical application, lithium batteries electrolytes, and etc. Within this work we have studied the possibility to utilize hydrosilylation and Piers-Rubinsztajn reactions to obtain cross-linked model phosphazene compounds, containing eugenoxy and guaiacoxy groups. It was shown that Piers-Rubinsztajn reaction cannot be efficiently used to prepare tailored polymer-matrix, due to the catalyst deactivation by nitrogen atoms of phosphazene units. A number of cross-linked phosphazene-based materials was obtained with the use of hydrosilylation reaction and their properties were studied by NMR spectroscopy, FTIR, DSC, and TGA. This work showed a perspective for the use of eugenoxy functional groups for the preparation of three-dimensional hybrid phosphazene/siloxane-based materials for various applications.

Fired bricks have shown tremendous potential as a construction material due to their properties. However, their use required some specifications in terms of quality, resistance, and durability. In developing countries, the lack of tools to make test specimens leads to many defects in these brick specimens responsible for low durability and weak precision during mechanical tests and shrinkage. In this study, a simple and traditional method of making test bricks is presented. This simple method allows the production of bricks with the required properties. This method is especially efficient for a firm or semi-soft pastes consistency. The handmade pastes do not stick into the walls of the mold like the case of steel molds and it gives specimens with standard shape, smooth surface, and sharp edges. The resulting fired bricks exhibit high mechanical strength comparable and even better than those of conventional methods.

In this work, the ternary titanium, copper and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by x-ray diffraction (XRD), nanoindentation (modulus and hardness) and Atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel.

Recently, two chicken breast fillet abnormalities, termed Wooden Breast (WB) and Spaghetti Meat (SM), have become a challenge for the chicken meat industry. The two abnormalities share some overlapping morphological features, including myofiber necrosis, intramuscular fat deposition, and collagen fibrosis, but display very different textural properties. WB has a hard, rigid surface, while the SM has a soft and stringy surface. Connective tissue is affected in both WB and SM, and accordingly, this study's objective was to investigate the major component of connective tissue, collagen. The collagen structure was compared with normal (NO) fillets using histological methods and Fourier transform infrared (FTIR) microspectroscopy and imaging. The histology analysis demonstrated an increase in the amount of connective tissue in the chicken abnormalities, particularly in the perimysium. The WB displayed a mixture of thin and thick collagen fibers, whereas the collagen fibers in SM were thinner, fewer, and shorter. For both, the collagen fibers were oriented in multiple directions. The FTIR data showed that WB contained more β-sheets than the NO and the SM fillets, whereas SM fillets expressed the lowest mature collagen fibers. This insight into the molecular changes can help to explain the underlying causes of the abnormalities.

This paper presents a method to determine material constants of a standard basketball shell together with the development of a virtual numerical model of a basketball. Material constants were used as the basis for the hyperelastic material model in the strain energy function (SEF). Material properties were determined experimentally by strength testing in uniaxial tensile tests. Additionally, the digital image correlation technique (DIC) was applied to measure strain in axial planar specimens, thus providing input stress-strain data for the Autodesk software. Analysis of testing results facilitated the construction of a hyperelastic material model. The optimal Ogden material model was selected. Two computer programmes by Autodesk were used to construct the geometry of the virtual basketball model and to conduct simulation experiments. Geometry was designed using Autodesk Inventor Professional 2017, while Autodesk Simulation Mechanical 2017 was applied in simulation experiments. Simulation calculations of the model basketball bounce values were verified according to the FIBA recommendations. These recommendations refer to the conditions and parameters which should be met by an actual basketball. A comparison of experimental testing and digital calculation results provided insight into the application of numerical calculations, designing of structural and material solutions for sports floors.

The implementation of gold-hydrogel core-shell nanomaterials in novel light-driven technologies requires the development of well-controlled and scalable synthesis protocols with precisely tunable properties. Herein, new insights are presented concerning the importance of using the concentration of gold cores as a control parameter in the seeded precipitation polymerization process to modulate – regardless of core size – relevant fabrication parameters such as encapsulation yield, particle size and shrinkage capacity. Controlling the number of nucleation points results in the facile tuning of the encapsulation process, with yields reaching 99% of gold cores even when using different core sizes at a given particle concentration. This demonstration is extended to the encapsulation of bimodal gold core mixtures with equally precise control on the encapsulation yield, suggesting that this principle could be extended to encapsulating cores composed of other materials. These findings could have significant impact on the development of stimuli-responsive smart materials.

The calculation of the vapour pressure of organic molecules at 298.15K is presented using a commonly applicable computer algorithm based on the group-additivity method. The basic principle of this method rests on the complete breakdown of the molecules into their constituting atoms, further characterized by their immediate neighbour atoms. The group contributions are calculated by means of a fast Gauss-Seidel fitting algorithm using the experimental data of 2036 molecules from literature. A ten-fold cross-validation procedure has been carried out to test the applicability of this method, which confirmed excellent quality for the prediction of the vapour pressure, expressed in log(pa), with a cross-validated correlation coefficient Q2 of 0.9938 and a standard deviation  of 0.26. Based on these data, the molecules' standard Gibbs free energy G°vap has been calculated. Furthermore, using their enthalpies of vaporization, predicted by an analogous group-additivity approach published earlier, the standard entropy of vaporization S°vap has been determined and compared with experimental data of 1129 molecules, exhibiting excellent conformance with a correlation coefficient R2 of 0.9598, a standard error  of 8.14 J/mol/K and a medium absolute deviation of 4.68%.

A phosphate/molybdate and cerium-modified phosphate/molybdate conversion coatings were deposited on a carbon steel surface and their protective and self-healing abilities were evaluated. Surface morphology and inner structure of the coatings were examined using FE-SEM-FIB and TEM techniques, chemical composition and element distribution depth profiles in conversion layers were determined using EDX measurements, whereas XPS was applied for the analysis of Mo and Ce oxidation states. Voltammetric measurements and EIS were performed to assess the corrosion behavior of the samples. The higher protective and stronger self-healing abilities were found for phosphate/molybdate/cerium conversion coating deposited in a sulphate-containing solution. This was attributed to higher values of both: total cerium and Ce(IV) content in the conversion layer as well as to lower number of structural defects in the coating. It was demonstrated that the micro-structural characteristics of protective coatings are also important in determining self-healing abilities.

Shiga toxigenic E. coli (STEC) are an important cause of foodborne disease globally with many outbreaks linked to the consumption of contaminated foods such as leafy greens. Existing methods for STEC detection and isolation are time-consuming. Rapid methods may assist in preventing contaminated products from reaching consumers. This proof-of-concept study aimed to determine if a metabolomics approach could be used to detect STEC contamination in spinach. Using untargeted metabolic profiling, the bacterial pellets and supernatants arising from bacterial and inoculated spinach enrichments were investigated for the presence of unique metabolites that enabled categorization of three E. coli risk groups. A total of 109 and 471 metabolite features were identified in bacterial and inoculated spinach enrichments, respectively. Supervised OPLS-DA analysis demonstrated clear dis-crimination between bacterial enrichments containing different risk groups. Further analysis of the spinach enrichments determined that pathogen risk groups 1 and 2 could be easily discriminated from the other groups, though some clustering of risk groups 1 and 2 was observed, likely representing their genomic similarity. Biomarker discovery identified metabolites that were significantly associated with risk groups and may be appropriate targets for potential biosensor development. This study has confirmed that metabolomics can be used to identify the presence of pathogenic E. coli likely to be implicated in human disease.

Named herein “CytroCell”, the cellulosic material obtained via hydrodynamic cavitation of citrus processing waste in water is cellulose of low crystallinity, high porosity, good water holding capacity and good dispersibility in water. These properties, here demonstrated for the first time for lemon and grapefruit CytroCell, open the route to mass scale production of a useful functional material from a cheap and abundant biowaste. The process, indeed, does not require any pre-treatment of the raw material, and does not use acid, alkali, chemical oxidants or enzymes.

Astola Island is the first marine protected area of Pakistan acknowledged 2017, June 15. It is a rich biodiversity hotspot, Ramsar site inhabiting endangered species like Green turtle, Hawksbill turtle, and Arabian Humpback whale. A saw-scaled Russell’s viper is endemic to Island. Marine ecology of Astola Island is affected by plastic pollution resulting in coral destruction, ocean acidification, global warming, fishing nets blockage, water pollution, and coastal erosion. Zeolite catalyst synthesized from environmentally friendly way by coal fly ash to degrade collected plastic waste from Island into useful products in pyrolysis reactor. The synthesized catalyst functionalized further with three type of organosilane(1) Octyltriethoxysilane(OS),(2)Phenyltriethoxysilane(PS)(3)Vinyltriethoxysilane(VS).Zeolite functionalize with octyltriethoxy silane (ZO) shows the highest performance in plastic pyrolysis, resulting in lower degradation temperature, low residue and more product formation may be due to having long chain hydrocarbon and acidic sites. Plastic recycling is the promising solution to tackle plastic blooming issue. Which is negatively impacting all the compartments of ecosystem especially marine environment.

The widely adopted temperature for solid solution heat treatment (ST) for the conventionally fabricated Inconel 718 is 1100 °C for a hold time of 1 h or less. This ST scheme is however not enough to dissolve Laves and annihilate dislocations completely in samples fabricated with Laser metal powder bed fusion (L-PBF) additive manufacturing (AM)-Inconel 718. In spite this, the highest hardness obtained after aging for ST temperatures (970 - 1250 °C) is at 1100 °C/1h [1]. The unreleased residual stresses in the retained lattice defects are potentially affecting other properties of the material. Hence, this work aims to investigate if a longer hold time of ST at 1100 °C will lead to complete recrystallization while maintaining the strength after aging or not. For this study, L-PBF-Inconel 718 samples were ST at 1100 °C at various hold times (1, 3, 6, 9, 16 or 24 h) and aged to study the effects on microstructure and hardness. In addition, a sample was directly aged to study the effects of bypassing ST. The samples (ST and aged) gain hardness by 43 – 49 %, depending on hold time. A high density of annealing twins evolved during 3 h of ST and the quantity only slightly varies for longer ST.

Graphene and borophene are highly attractive two-dimensional materials with outstanding physical properties. In this study we employed a combined atomistic continuum multiscale modeling to explore the effective thermal conductivity of polymers nanocomposites made of PDMS polymer as the matrix and graphene and borophene as nanofillers. We first conduct classical molecular dynamics simulations to investigate the interfacial thermal conductance between graphene/PDMS and borophene/PDMS interfaces. Acquired results confirm that the interfacial thermal conductance between nanosheets and polymer increases from the single-layer to multilayered nanosheets and finally converges. The data provided by the atomistic simulations were then used in the finite element method simulations to evaluate the effective thermal conductivity of polymer nanocomposites at continuum level. We explore the effects of nanofillers type, their volume content, geometry aspect ratio and thickness on the nanocomposites effective thermal conductivity. As a very interesting finding, we show that borophene nanosheets, despite almost two orders of magnitude lower thermal conductivity than graphene, can yield very close enhancement in the effective thermal conductivity in comparison with graphene, particularly for low volume content and small aspect ratios and thicknesses. We conclude that for the polymer-based nanocomposites, significant improvement in the thermal conductivity can be reached by improving the bonding between the fillers and polymer or in another word enhancing the thermal conductance at the interface. By taking into account the high electrical conductivity of borophene, our results suggest borophene nanosheets as promising nanofillers to simultaneously enhance the polymers thermal and electrical conductivity.

Sparkling wine producing and consumption are in constant increase in the last decade and show no sign of slowing. Prior consumption, origin, grape variety, occasion, price and sensorial perception are factors that typically influence wine consumers’ purchasing and consumption behavior. The presence of volatile compounds in sparkling wines, with direct impact on their organoleptic characteristics, is influenced by several factors, such as the base-wine characteristics, grapes cultivar conditions, the used yeasts, the aging stage or wine-making practices. For this study, five sparkling wines variants from Muscat Ottonel grape variety were obtained. For the experimental samples, the grapes were processed by applying secondary fermentation in bottles. The base-wine was obtained through reverse osmosis and had a predetermined alcoholic concentration (10.5 % vol.). This study aimed to analyze the influence of different commercial yeasts (IOC FIZZ™, IOC DIVINE™, LEVULIA CRISTAL™, IOC 18-2007™) on the volatile composition of experimental sparkling wines. The obtained sparkling wines were characterized by the physical-chemical parameters (according to OIV methods of analysis) and volatile fraction (using gas-chromatography). Data showed an important impact on the concentration of the volatile compounds (p &lt; 0.05), depending on the type of inoculated yeast for the second fermentation and only a minor influence on the physical-chemical parameters was registered.

In this paper, the definition of information entropy of Smoluchowski coagulation equation for Brownian motion is introduced based on coagulation probability. The expression of entropy is the function of geometric average particle volume and standard deviation with lognormal distribution assumption. The asymptotic solution with moment method shows that the entropy is a monotone increasing function of time, which is equivalence to the entropy based on particle size distribution. the result reveals that the present definition of entropy of Smoluchowski coagulation equation are inadequate because the particle average volume at equilibrium cannot be determined from the principle of maximum entropy. This provides a basis for further exploring the global properties of Smoluchowski coagulation equation.

The environmental and economic concern is the biggest challenge that concrete industry is facing today. Advancement in utilization of wastes in concrete as a mixture reduces usage of natural resources. Phyllite is a kind of foliated metamorphic rock generates during underground mining .Phyllite was calcined at 850 to 900oC in furnace and ground in ball mill. In this study, cement was partially replaced by weight with calcined phyllite to make M30 grade of concrete with 0% (Control mix), 2%, 4%, 6%, 8%, & 10%, (which are designated as M1, M2, M3, M4, M5 and M6). The laboratory tests such as slump value, compressive strength, flexural strength, water absorption, chloride ion penetration and durability in acidic and basic medium were conducted on the phyllite concrete and results are compared with the control mix. Through results it is concluded that cement can be replaced in concrete at the tune of 8% with Calcine Phyllite (CP) without affecting the strength and durability. The aim of the experiment is to find the maximum content of mines calcined Phyllite that can be used as a partial replacement of cement without compromising the quality on any of the characteristics of concrete.

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect based devices, biological applications, and nitrogen-vacancy color center based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and future outlook in this area.

The effect of Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results demonstrate that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites in the weld metal, and significantly improve the toughness. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. Excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties.

Intensive development of many industries, including textile, paper or plastic, which consume large amounts of water and generate huge amounts of wastewaters containing toxic dyes, contribute to pollution of the aquatic environment. Among many known methods of wastewater treatment, adsorption techniques are considered as the most effective. In the present study the weakly basic anion exchangers such as Amberlyst A21, Amberlyst A23 and Amberlyst A24 of the polystyrene, phenol-formaldehyde and polyacrylic matrices were used for C.I. Direct Yellow 50 removal from aqueous solutions. The equilibrium adsorption data were well fitted to the Langmuir adsorption isotherm. Kinetic studies were described by the pseudo-second order model. The pseudo-second order rate constants were in the range of 0.0609-0.0128 g/mg·min for Amberlyst A24, 0.0038-0.0015 g/mg·min for Amberlyst A21 and 1.1945-0.0032 g/mg·min for Amberlyst A23, and decreased with the increasing initial concentration of dye from 100-500 mg/L, respectively. There were observed auxiliaries (Na2CO3, Na2SO4, anionic and non-ionic surfactants) impact on the dye uptake. The polyacrylic resin Amberlyst A24 can be promising sorbent for C.I. Direct Yellow 50 removal as it is able to uptake 666.5 mg/g of the dye compared to the phenol-formaldehyde Amberlyst A23 of the 284.3 mg/g capacity.

This paper investigates the photocatalytic characteristics of Ag Nanowire (AgNW)/TiO2 and AgNW/TiO2/Graphene oxide (GO) nanocomposites. Samples were synthesized by the direct coating of TiO2 particles on the surface of silver nanowires. As-prepared AgNW/TiO2 and AgNW/TiO2/GO nanocomposites were characterized by electron microscopy, X-ray diffraction, UV/visible absorption spectroscopy, and infrared spectroscopy. Transmission electron microscope (TEM) images confirmed the successful deposition of TiO2 nanoparticles on the surface of AgNWs. The photocatalytic activity of synthesized nanocomposites was evaluated using Rhodamine B (RhB) in an aqueous solution as the model organic dye. Results showed that synthesized AgNW/TiO2/GO nanocomposite has superior photocatalytic activities when it comes to the decomposition of RhB.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

The association between human and cat (F. catus) is well known. This domestic animal is also known for its malodorous urine and feces. The complexity of the odorous urine and feces impacts human life by triggering the human sensory organ in a negative way. The objective of this research was to identify the volatile organic chemicals (VOCs) and associated odors in cat urine and feces using gas chromatography-mass spectrometry and simultaneous sensory analysis of fresh and aged samples. The solid-phase microextraction (SPME) technique was used to pre-concentrate the VOCs emitted from urine or feces samples. Twenty-one compounds were identified as emitted from fresh urine, whereas 64 compounds were emitted from fresh feces. A contrasting temporal impact was observed on the emission of VOCs for urine and feces. On aging, the emission increased to 36 detected chemicals for stale urine, whereas only 17 chemicals were detected in stale feces. Not all compounds were malodorous; some compounds had a pleasant hedonic smell to the human nose. Although trimethylamine, low molecular weight organic acids, and ketones were contributors to the odor to some extent, phenolic compounds and aromatic heterocyclic organic N compounds generated the most intense odors and substantially contributed to the overall malodor, as observed by this study. This work might be useful to formulate cat urine and feces odor remediation approaches to reduce odor impacts.

Various techniques have been used to “clean-up” industrial phosphoric acid: precipitation, flotation, activated charcoal or clay treatment. To address membrane processes potential in phosphoric acid clarification process, this study explores the advantage of membrane techniques as new route for phosphoric acid clarification in an eco-efficient way through the use of “regenerated spent membrane”. Regeneration of the spent membranes was performed on of 0.15 m2 active area regeneration. These membrane samples were used to study the phosphoric acid clarification at a laboratory scale. They were immersed in an oxidizer for at most seven days. The samples were characterized systematically before immersion in an oxidant media. In this study, the potential to regenerate spent membranes and application of this media to clarify the 29% P2O5 phosphoric acid was demonstrated. This study shows, by tests that the reverse osmosis (RO) membranes achieve an abatement of 70% and 65% for solids and organic materials, respectively. These positive results will pave the way for implementing these membranes phosphoric acid treatment process. Moreover, besides being economically advantageous, the use of the spent membrane is likely an environmentally friendly route (no waste, no organic solvent and effluent to be regenerated later on).

Silicone RTV-based engineering rubber composite products have been widely used for several applications in various fields as a major component such as structure, automotive, and medical. In its application, the rubber composite product is placed in an open area that is directly exposed to sunlight and rain. It has a significant negative impact on changes in chemical and rheological properties, making the product life of rubber composite products shorter. Therefore, in this study, changes in the chemical and rheological properties of both isotropic and anisotropic magnetorheological elastomer (MRE) treated with accelerated weathering were studied compared to untreated specimens with specimens that had been treated. MRE specimens with 40% by weight CIP were prepared with no current excitation and another sample were made under 1.5 T of magnetic flux density. Each specimen was treated in an accelerated weathering machine Q-Sun Xe-1 Xenon Test Chamber with a UV light exposure cycle for 102 minutes and 18 minutes of UV light combined with water spray for 24 hours followed by a condensation cycle of 4 hours in a dark period. Material characterization was carried out using FTIR and Rheometer to determine the changes in chemical and rheological properties. The morphological analysis results showed that the surface was rough and more cavities occurred after being given weather treatment. Rheometer test results showed a decrease in storage modulus in each MRE specimen that had been treated compared to untreated MRE specimens. Meanwhile, FTIR testing showed a change in wave peak between untreated and treated MRE specimens.

In this study, a summary of the processes performed on the SPL for recycling, reduction in toxicity and treatment were examined on an industrial and laboratory scale. In writing this research, an attempt has been made to address the useful processes that have taken place in this field. Spent pot lining or SPL is a type of solid waste that is produced in the aluminum production process. After 3 to 8 years, the cathode blocks become problematic and can no longer be used, and need to be replaced due to adverse effects on cell function. SPL is known to be a hazardous waste to nature due to its fluoride and cyanide content. Research has shown that SPL ingredients have destructive and very dangerous effects on human DNA, which is why they are so important to maintain and recycle.

Primary hyperoxalurias (PHs) are a group of inherited alterations of the hepatic glyoxylate metabolism. PHs classification based on gene mutations parallel a variety of enzymatic defects, and all involve the harmful accumulation of calcium oxalate crystals that produce systemic damage. These geographically widespread rare diseases have a deep impact in the life quality of the patients. Until recently, treatments were limited to palliative measures and kidney/liver transplants in the most severe forms. Efforts made to develop pharmacological treatments succeeded with the biotechnological agent lumasiran, a siRNA product against glycolate oxidase, which has become the first effective therapy to treat PH1. However, small molecule drugs have classically been preferred since they benefit from experience and have better pharmacological properties. The development of small molecule inhibitors designed against key enzymes of glyoxylate metabolism is on the focus of research. Enzyme inhibitors are successful and widely used in several diseases and their pharmacokinetic advantages are well known. In PHs, effective enzymatic targets have been determined and characterized for drug design and interesting inhibitory activities have been achieved both in vitro and in vivo. This review describes the most recent advances towards the development of small molecule enzyme inhibitors in the treatment of PHs, introducing the multi-target approach as a more effective and safe therapeutic option.

Recently, significant events took place that added immensely to the sociotechnical pressure for developing sustainable composite recycling solutions, namely (1) a ban on composite landfilling in Germany in 2009, (2) the first major wave of composite wind turbines reaching their End-of-Life (EoL) and being decommissioned in 2019-2020, (3) the acceleration of aircraft decommissioning due to the COVID-19 pandemic, and (4) the increase of composites in mass production cars, thanks to the development of high volume technologies based on thermoplastic composites. Such sociotechnical pressure will only grow in the upcoming decade of 2020s as other countries are to follow Germany by limiting and banning landfill options, and by the ever-growing number of expired composites EoL waste. The recycling of composite materials will therefore play an important role in the future, in particular for the wind energy, but also for aerospace, automotive, construction and marine sectors to reduce environmental impacts and to meet the demand. The scope of this manuscript is a clear and condensed yet full state-of-the-art overview of the available composite recycling technologies of both low and high Technology Readiness Levels (TRL). TRL is a framework that has been used in many variations across industries to provide a measurement of technology maturity from idea generation (basic principles) to commercialization. In other words, this work should be treated as a technology review providing guidelines for the sustainable development of the industry that will benefit the society. The authors propose that one of the key aspects for the development of sustainable recycling technology is to identify the optimal recycling methods for different types of composites. Why is that the case can be answered with a simple price comparison of E-glass fibers (~2 $/kg) versus a typical carbon fiber on the market (~20 $/kg) – which of the two is more valuable to recover? However, the answer is more complicated than that – the glass fiber constitutes about 90% of the modern reinforcement market, and it is clear that different technologies are needed. Therefore, this work aims to provide clear guidelines for economically and environmentally sustainable End-of-Life (EoL) solutions and development of the composite material recycling.

Heterogeneous distribution of delivery or treatment modalities within the tumor mass is a crucial limiting factor for a vast range of theranostic applications. Understanding the interactions between a nanomaterial and the tumor microenvironment will help to overcome challenges associated with tumor heterogeneity as well as the clinical translation of nanotheranostic materials. This study aims to evaluate the influence of protein surface adsorption on gold nanoparticle (GNP) biodistribution using high resolution Computed Tomography (CT) preclinical imaging in C57BL/6 mice harboring Lewis Lung Carcinoma (LLC) tumors. LLC provides a valuable model for study due to its highly heterogenous nature which makes drug delivery to the tumor challenging. By controlling the adsorption of proteins on the GNP surface, we hypothesize that we can influence the intratumoral distribution pattern and particle retention. We performed an in vitro study to evaluate the uptake of GNPs by LLC cells and an in vivo study to assess and quantify the GNP biodistribution by injecting concentrated GNPs citrate stabilized or passivated with Bovine Serum Albumin (BSA) intratumorally into LLC solid tumors. Quantitative CT and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES) results both confirm the presence of particles in the tumor 9 days post-injection (n=8 mice/group). Significant difference is highlighted between citrate-GNP and BSA-GNP groups (**p < 0.005, Tukey’s multiple comparisons test), confirming the protein corona of GNPs modifies intratumoral distribution and retention of the particles. In conclusion, our investigations show that the surface passivation of GNPs influences the mechanism of cellular uptake and intratumoral distribution in vivo highlighting the spatial heterogeneity of the solid tumor.

Plant proteins being considered to become the most important protein source of the future, they must be able to replace the animal-derived proteins currently in use as technofunctional food ingredients. This poses challenges because plant proteins are oftentimes storage proteins with a high molecular weight and low water solubility. One promising approach to overcome these limitations is the glycation of plant proteins. The covalent bonding between the proteins and different carbohydrates created via the initial stage of the Maillard reaction can improve the technofunctional characteristics of these proteins without the involvement of potentially toxic chemicals. However, compared to studies with animal-derived proteins, glycation studies on plant proteins are currently still underrepresented in literature. This review provides an overview of the existing studies on the glycation of the major groups of plant proteins with different carbohydrates using different preparation methods. Emphasis is put on the reaction conditions used for glycation as well as the modifications to physicochemical properties and technofunctionality. Different applications of these glycated plant proteins in emulsions, foams, films, and encapsulation systems are introduced. Another focus lies on the reaction chemistry of the Maillard reaction and ways to harness it for controlled glycation and to limit the formation of undesired advanced glycation products. Finally, challenges related to the controlled glycation of plant proteins to improve their properties are discussed.

The elimination of superoxide radical anions (O2•−) by 5-amino-2-hydroxybenzoic acid (mesalazine, 5-ASA), 4-amino-2-hydroxybenzoic acid (4-ASA), and related compounds used for ulcerative colitis treatment was investigated using cyclic voltammetry and electron spin resonance (ESR) analyses aided by density functional theory (DFT) calculations. Quasi-reversible O2/O2•− redox was found to be modified by the compounds, suggesting that an acid-base reaction in which a hydroperoxyl radical (HO2•) is formed from O2•− occurs. However, the deprotonated 5-ASA anion can eliminate O2•− through proton-coupled electron transfer (PCET), forming a radical product. This electron transfer (ET) was confirmed by ESR analysis. The 4-aminophenol moiety in 5-ASA plays an important role in the PCET involving two proton transfers and one ET based on -conjugation. The electrochemical and DFT results indicated that O2•− elimination by 5-ASA proceeds efficiently viathrough the PCET mechanism after deprotonation of the 1-carboxyl group. Thus, 5-ASA may act as an anti-inflammatory agent in the alkali intestine through PCET-based O2•− elimination.

Levels of synthetic musk fragrances (SMFs) and various personal care products (PCPs) were measured in the Han River and its tributaries in Seoul, Korea. The most abundant SMF in all river and PCP samples was 4,6,6,7,8,8-hexamethyl-1,3,4,7-tetrahydrocyclopenta[g]isochromene (HHCB), followed by 1-(3,5,5,6,8,8-hexamethyl-6,7-dihydronaphthalen-2-yl)ethanone (AHTN), musk ketone (MK), and 1,1,2,3,3-pentamethyl-2,5,6,7-tetrahydroinden-4-one (DPMI). There was a significant correlation between the SMF concentration in the PCPs and the Han River samples. Moving from upstream to downstream in the Han River, the median SMF concentration was 6.756, 2.945, 0.304, and 0.141 μg/L in the sewage treatment plant (STP) influent, effluent, tributaries, and mainstream, respectively, implying that effective SMF removal was achieved during the sewage treatment process, followed by dilution in the receiving water. Four STPs using advanced biological treatment processes had removal efficiencies of 55.8%, 50.6%, 43.3% for HHCB, AHTN, and MK, respectively. The highest SMF concentrations in the tributaries were observed at locations close to the STPs. Our study confirmed that the main source of SMFs in the receiving water were sewage effluent containing untreated SMFs, which are largely originated from household PCPs, especially hair care products (e.g., shampoo) and perfumes.

The current paper is focused on the rapidly developing field of nano-/micro three-dimensional production of inorganic materials. The fabrication method includes laserlithography of hybrid organic-inorganic materials with subsequent heat treatment lead-ing to a variety of crystalline phases in 3D structures. In this work, it was examineda series of organometallic polymer precursors with different silicon (Si) and zirconium (Zr) molar ratios, ranging from 9:1 to 5:5, prepared via sol-gel method. All mixtureswere examined for perspective used in 3D laser by manufacturing by fabricating nano-and micro-feature sized structures. Their deformation and surface morphology wereevaluated depending on chemical composition and crystallographic phase. The appear-ance of a crystalline phase was proven using single-crystal X-ray diffraction analysis,which revealed a lower crystallization temperature for microstructures compared tobulk materials. Fabricated 3D objects retain a complex geometry without any distortion after heat treatment up to 1400^oC. Under the proper conditions, a zircon phase (ZrSiO₄ - a highly stable material) can be observed. In addition, the highest newrecord of achieved resolution below 60 nm has been reached. The proposed prepara-tion protocol can be used to manufacture micro/nano-devices with high precision andresistance to high temperature and aggressive environment.

A novel type of phosphazene containing additive that act both as catalyst and as flame retardant for benzoxazine binders is presented in this study. The synthesis of a derivative of hexachlorocyclotriphosphazene (HCP) and meta-toluidine was carried out in the medium of the latter, which made it possible to achieve complete substitution of chlorine atoms in the initial HCP. Thermal and flammability characteristics of modified compositions are revealed. The modifier catalyzes the process of curing and shifts the beginning of reaction from 222.0 C for pure benzoxazine to 205.9 C for composition with 10 phr of modifier. The additive decreases the glass transition temperature of compositions. Achievement of the highest category of flame resistance (V-0 in accordance with UL-94) is ensured both by increasing the content of phenyl residues in the composition and by the synergistic effect of phosphorus and nitrogen. Brief research of the curing kinetics disclosed the complex nature of the reaction. An accurate two-step model is obtained using extended Prout-Tompkins equation for both steps.

The oral administration of (R)-3-hydroxybutyl-(R)-3-hydroxybutyrate, allows inducing a beneficial level of blood ketone bodies without the adverse effects due to the adhesion to a ketogenic diet. Several studies documented the therapeutic effectiveness of the (R)-3-hydroxybutyl (R)-3-hydroxybutyrate in treating neurodegenerative diseases as well as its boosting activity of athletic and cognitive performances during prolonged physical exercises. Further studies considering this ketone body ester for therapy of other pathologies are also underway. In the present work, we describe the synthesis of (R)-3-hydroxybutyl-(R)-3-hydroxybutyrate through the enantioselective transesterification of racemic ethyl 3-hydroxybutyrate with (R)-1,3-butanediol catalyzed by immobilized Candida antarctica lipase B (CAL-B). The enantiopure (R)-1,3-butanediol was in turn obtained from the kinetic resolution of the racemate by CAL-B catalyzed acetylation with vinyl acetate. The economy of the synthetic procedure has been improved by recycling the unreacted (S) enantiomers of the ethyl 3-hydroxybutyrate and 1,3-buatnediol after stereochemical inversion achieved by tosylation and SN2 with ammonium acetate. The overall procedure allows to incorporate up to 70% of the starting racemic reagents into the final product.

Due to the rapid development of nanotechnologies, materials, in particular , solid dispersions (SDs), which are actively introduced into the life of modern man, have been obtained. Special progress in this area is observed in industry and medicine. The use of SDs in agriculture is lagging far behind, despite the growing number of scientific papers on this topic. At the same time, the prospects for the introduction of SDs in the agro-industrial complex are obvious. The review presents the results of research on the development of innovative preparations based on SD to protect plants from diseases and pests of cultivated plants, as well as parasiticides to protect animal health based on modern achievements of nanotechnology. One of these technologies is the methods of mechanochemistry, which improve the properties of poorly soluble biologically active substances by their joint mechanical treatment with water-soluble polymers and auxiliary substances.

In recent years, many studies have highlighted the consistent finding of amoxicillin in waters destined for wastewater treatment plants, in addition to superficial waters of rivers and lakes in both Europe and North America. In this paper, the amoxicillin degradation pathway was investigated by simulating the chlorination process normally used in a wastewater treatment plant to reduce similar emerging pollutants at three different pH values. The structures of 16 isolated degradation byproducts (DPs), one of which was isolated for the first time, were separated on a C-18 column via a gradient HPLC method. Then, combining mass spectrometry (MALDI-MS/TOF) and nuclear magnetic resonance, we compared commercial standards and justified a proposed formation mechanism beginning from the parent drug. Microbial growth inhibition bioassays with Escherichia coli, Klebsiella pneumoniae, and Staphylococcus aureus were performed to determine the potential loss of antibacterial activity in isolated degradation byproducts. An increase of antibacterial activity in the DPs was observed compared to the parent compound.

Sewage sludge was utilized into biochar using the slow pyrolysis method. The biochar was then being used for ammonium removal. The sewage sludge biochar was produced at temperature of 550°C, 600°C, 650°C, 700°C and 750°C. A few characterization tests were carried out to study about the physical and chemical properties of the biochar. For instance, moisture and ash content analysis, FTIR spectroscopy, pH Zero Point Charge, biochar yield and SEM. As the pyrolysis temperature increased, the moisture content of SSB decreased while the ash content increased. The FTIR spectra of sewage sludge biochar showed that there were various organic functional groups on the surface of the biochar which were responsible for ammonium adsorption. Furthermore, through pH Zero Point Charge analysis, pH 7.0 was the most optimum pH for the adsorption test of ammonium. The optimum adsorbent dosage was 0.01g while optimum contact time was 150 minutes. Furthermore, 1.2ppm was the most optimum concentration for adsorption process. Based on the result of the characterization tests, SSB700 was the most effective biochar for ammonium adsorption. Based on the result of kinetic and isotherm analysis, the adsorption of ammonium ions usign sewage sludge biochar was a monolayer chemisorption process.

The utilisation of the industrial residual products to develop new value-added materials and to reduce footprint is one of the critical challenges of science and industry. Development of the new multifunctional and bio-based composites materials is an excellent opportunity for the effective utilisation of industrial residual products. Keeping the different issues in mind, in this work, we describe the manufacturing and characterisation of the three-phases bio-based composites. The key components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash, i.e. the cenosphere (CS). The three-phase composite prepared in the form of a block were investigated for their mechanical properties and density. The three-phase composite was prepared in the form a) of a block were investigated for their mechanical properties, and density and b) a form of granules for determination of the water and oil products sorption were investigated. We have also investigated the dependence of the properties on the DCR and CS fraction. It has been found, that maximum compression strength (in block form) observed for composition without CS and DCR addition was- 79.3 MPa, while the second-highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt%, the compression strength is in the range from 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.

As a result of this work, a previously unreported benzoxazine monomer based on 3,3'-dichloro-4,4'-diaminodiphenylmethane was obtained, characterized by 1H and 13C NMR spectroscopy, and its thermal and rheological properties were studied. A comparison between the properties of benzoxazines based on diamines (3,3'-dichloro-4,4'-diaminodiphenylmethane and 4,4’-diaminodimethylmethane). The effect of the reaction medium on the structure of the oligomeric fraction and the overall yield of the main product was studied. The synthesized monomers can be used as thermo- and fire-resistant binders for polymer composite materials, as well as hardeners for epoxy resins.

The synthesis of additives for thinning mineral suspensions based on sodium polyacrylate was carried out. The effect of molecular weight regulators on the molecular weight characteristics of the polymer and the effect of such polymers on the rheological properties of suspensions was studied. Sodium acrylate polymers are synthesized by free radical polymerization in aqueous solution using molecular weight regulators. The molecular weight characteristics of the polymeric samples were estimated by viscometry using Mark-Houwink-Kuhn-Sakurada (MHKS) equation. Synthesized polymers were used as thinners ceramic slurries, prepared according to the recipe of the enterprises producing ceramic products. The thinning ability of polymer samples with different molecular weights was estimated using an Engler viscometer from the time of the ceramic slurry flow. The influence of the type and amount molecular weight regulator on polyacryates was revealed. It was found that molecular weight synthesized samples was in the range of 21000 - 91000. It was determined that samples with a molecular weight of 28000 - 35000 synthesized using mercaptoethanol (at a dosage of 0.5-1.5% by weight of the monomer) provide optimal fluidity to the ceramic slurry.

New pharmaceutically acceptable salts of trazodone for the treatment of central nervous system disorders are synthesized and described. Each salt (trazodone hydrogen bromide and trazodone 1-hydroxy-2-naphthoate) was obtained by two or three different methods leading to the same crystalline form. Although trazodone salts are poorly crystalline, single-crystal X-ray diffraction data for trazodone 1-hydroxy-2-naphthoate were collected and analyzed as well as compared to the previously described crystal structure of commercially available trazodone hydrochloride. The powder samples of all new salts were characterized by Fourier transform infrared spectroscopy and 13C solid-state nuclear magnetic resonance spectroscopy. Spectroscopic studies were supported by gauge including projector augmented wave (GIPAW) calculations of carbon chemical shielding constants. The main goal of our research was to find salts with better physicochemical properties and to make an attempt to associate them with both the anion structure and the most prominent interactions exhibited by the protonated trazodone cation. The dissolution profiles of trazodone from tablets prepared from various salts with lactose monohydrate were investigated. The studies revealed that salts with simple anions show a fast release of the drug while the presence of more complex anion, more strongly interacting with the cation, effects a slow-release profile of the active substance and can be used for the preparation of the tables with a delay or prolonged mode of action.

Abstract: Age-related macular degeneration (AMD) is the leading cause of central blindness in developed countries. It affects people mainly over the age of 50 years. It is a disease of the macula, an area of the retina responsible for sharp central vision. It particularly affects the Bruch’s membrane (BM); a layer in the retina that acts as the basement upon which retinal pigment epithelial cells (RPE) attach and survive. The pathology of AMD is not fully understood, but age is considered the main risk factor. There are two forms; nonexudative, leading to the end-stage of the disease, called nonexudative (or dry) AMD (90% of cases) where fatty deposits called drusen form under the RPE on top of the BM lifting off the RPE, and neovascular (or wet) AMD (10% of cases) where abnormal new blood vessels grow and push through the BM, bleeding in and disrupting the RPE. Neovascular AMD is well controlled with regular antiangiogenic drug injections of anti-vascular endothelial growth factor (anti-VEGF) into the eye, whereas there is no current treatment for nonexudative AMD. Many research groups across the world are working on a treatment for nonexudative AMD. This review discusses the research currently being conducted including cell therapies, development of cell transplantation membranes, targeting other disease structures in affected retina (i.e. drusen), and drug delivery to the retina using nanoparticles. Finally, we include our research contributing to the field; developing a bioactive membrane intended to function two-fold: target diseased structures and transplant healthy RPE to the desired area.

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO2 thin films were elucidated using real-time synchrotron radiation imaging, its structure determined using grazing incidence X-ray diffraction (GIXRD), its morphology imaged using the field emission scanning electron microscopy (FESEM), and its surface topography examined using the atomic force microscope (AFM) in contact mode. Cubical white spots were detected, identified as Ag, while the TiO₂ thin film resembles a porous ring-like structure with each ring coalescing and forming channels. Junction growth is directly proportional with time under continuous heating conditions (annealing), and its growth orientations and patterns were seemingly random.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.

This study aimed to assess the response of 3D printed PLA scaffolds biomimetically coated with apatite on human primary osteoblast spheroids and evaluate the biological response to its association with Bone Morphogenetic Protein 2 (rhBMP-2) in rat calvaria. PLA scaffolds were produced via 3D printing, soaked in simulated body fluid (SBF) solution, and characterized by physical-chemical, morphological, and mechanical properties. The in vitro biological response was assessed with human primary osteoblast (HOb) spheroids. The in vivo analysis was conducted through the implantation of 3D printed PLA scaffolds either alone, covered by apatite (PLA-CaP) or PLA-CaP loaded with rhBMP-2 (PLA-CaP+rhBMP-2) on critical-sized defects (8 mm) of rat calvaria. Increased cell adhesion and in vitro release of growth factors (PDGF, bFGF, VEGF) was observed for PLA-CaP scaffolds when pre-treated with FBS. PLA-CaP+BMP2 presented higher values of newly formed bone (NFB) than other groups at all experimental periods (p&lt;0.05), attaining 44.85% of NFB after 6 months. These findings indicate that functionalization of PLA scaffolds with biomimetic apatite can improve its biological properties in the presence of complex biological media. Its association with BMP2 may enhance bone repair, suggesting this strategy as a promising candidate for bone tissue engineering.

An ability of different molecular potentials to reproduce the properties of 2D molybdenum disulphide polymorphs is examined. Structural and mechanical properties, as well as phonon dispersion of the 2H, 1T and 1T’ single-layer MoS2 (SL MoS2) phases, were obtained using density functional theory (DFT) and molecular statics calculations (MS) with Stillinger-Weber, REBO, SNAP, and ReaxFF interatomic potentials. Quantitative systematic comparison and discussion of the results obtained are reported.

Sickle cell disease (SCD) is the most common hereditary disorder of hemoglobin (Hb) that affects approximately a millions people worldwide. It is characterized by a single nucleotide substitution on the β-globin gene, leading to the production of abnormal sickle hemoglobin with multi-system consequences. Mutated Hb leads to profound changes in: i) red blood cell metabolism and physiology; ii) endothelial signaling; and iii) immune response. Oxidative stress is an important hallmark of SCD. It plays a key role in the pathophysiology of hemolysis, vessel occlusion and the following organ damage in sickle cell patients. For this reason, reactive oxidizing species and the (end)-products of their oxidative reactions have been proposed as markers of both tissue pro-oxidant status and disease severity. Although more studies are needed to clarify their role, antioxidant agents have been shown to be effective in reducing pathological consequences of the disease by preventing oxidative damage in SCD, i.e. by decreasing the oxidant formation or repairing the induced damage. An improved understanding of oxidative stress will lead to targeted antioxidant therapies that should prevent or delay the development of organ complications in this patient population.

Vanadium containing slurry is a by-product of vanadium pentoxide by hydrometallurgical methods from vanadium slag. It is promising technogenic raw material for vanadium production. The phase analysis of vanadium-containing slurry by X-ray diffraction method has shown that it contains vanadium in spinel form (FeO∙V2O3). The various oxidation roasting methods for slurry treatment have been studied for increasing vanadium extraction into the solution. It has shown that the most effective additive is 1% CaCO3 at a roasting temperature of 1000 °C. The oxidation roasting of vanadium-containing slurry with the additive led to increase acid-soluble form of V2O5 from 1.5 to 3.7% and decrease the content of FeO∙V2O3 from 3 to 0.4%. These results have confirmed the efficiency of the application of oxidation roasting to convert vanadium compounds into acid-soluble forms. The conversion mechanism of spinel to acid-soluble phases during oxidation roasting with additives was investigated by thermogravimetric analysis and thermodynamic simulation. It has shown that the formation of acid-soluble calcium vanadates during oxidation roasting without additives occurs at temperatures above 800 °C, but СаСО3 addition allows to reduce this temperature to 600 °C.

The flow behavior of the administrated fluid matrices demands careful assessments for stability as consumed by individuals with dysphagia. In the present study, we incorporate tapioca starch (TS), hydroxypropyl distarch phosphate (HDP), and xanthan gum (XG) as thickeners into different nectars (300±20 mPa.s) undergoing thermal processing and evaluated their stability. The thickened nectars presented better water holding and oil binding capacities at 25 ℃ than 4 ℃, and the nectars with TS provided the best results for both capacities as well as the highest solubility index and swelling power (p<0.05). All prepared nectars appeared to be shear-thinning fluids with yield stress closely fitting the power law and Casson models. XG-contained nectars presented a higher yield stress and consistency index. Matrices thickened by HDP exhibited a higher viscoelastic property compared to those thickened by TS during thermal processing. TS nectars presented viscous behavior, whereas HDP and XG nectars presented elastic behavior at 80 ℃ processing. The 3-min thermal processing HDP-nectars remained stable and met dysphagia-friendly requirements under 4 ℃ storage for 28 days regardless of the types of fluid bases (distilled water, sport drink, or orange juice). The employed thickeners present adequate physicochemical properties to be potentially utilized for producing dysphagia-friendly formulations.

Earth-abundant transition metals like iron, nickel, copper, molybdenum, and vanadium have been identified as essential constituents of the cellular gas metabolism in all kingdoms of life. Associated with biological macromolecules, gas-processing metalloenzymes (GPMs) are formed that catalyse a variety of redox reactions. This includes the reduction of O₂ to water by cytochrome c oxidase (‘complex IV’), the reduction of N₂ to NH₄ by nitrogenase, as well as the reduction of protons to H₂ (and oxidation of the later) by hydrogenase. GPMs perform at ambient temperature and pressure, in the presence of water, and often extremely low educt concentrations, thus serving as natural examples for efficient catalysis. Facilitating the design of biomimetic catalysts, biophysicist thrive to understand the reaction principles of GPMs making use of various techniques. In this perspective, I will introduce Fourier-transform infrared spectroscopy in attenuated total reflection configuration (ATR FTIR) for the analysis of GPMs like cytochrome c oxidase, nitrogenase, and hydrogenase. Infrared spectroscopy provides information about the geometry and redox state of the catalytic cofactors, the protonation state of amino acid residues, the hydrogen-bonding network, and protein structural changes. I developed an approach to probe and trigger the reaction of GPMs by gas exchange experiments, exploring the reactivity of these enzymes with their natural reactants. This allows recording sensitive ATR FTIR difference spectra with seconds time resolution. Finally yet importantly, infrared spectroscopy is an electronically non-invasive technique that allows investigating protein samples under biologically relevant conditions, i.e., at ambient temperature and pressure, and in the presence of water.