This paper presents an extensive performance analysis of open-ended waveguide elements for direct radiating arrays with high scan angle (± 50º/60º). The evaluated designs are based on square and hexagonal apertures loaded with ridges. Both square and triangular lattices are considered in the framework of Ka-band downlink design requirements for future LEO mega-constellations. The parameter space defined by the monomodal condition has been explored to find an optimum value for each structure. The analyses are validated with both infinite and finite full-wave models in terms of active reflection coefficient, scan loss and cross-polar discrimination.

Steel construction is used more often these days as an alternative to the R.C.C. when light weight, high strength, large-span structures with a faster erection are required. Extensive studies have been done by researchers to study the seismic performance of reinforced concrete and steel structures, both in terms of elastic and inelastic behavior. Composite construction is also a recent advancement in the building industry with similar advantages. However, no emphasis has been given to the comparison between the inelastic behavior of steel and composite structures when subjected to lateral loads. This study compares the inelastic behavior of steel and a composite frame designed to have the same plastic moment capacity for structural members. The responses, such as the formation of hinges, story drifts, story displacements, lateral stiffness, ductility, maximum strength, energy dissipated, joint accelerations, and performance points, are compared with the aid of the building analysis and design software ETABS-18. For this, response spectrum analysis, pushover analysis and nonlinear direct integration time history analysis have been performed on both frames. For design and analysis, international codes such as IS 800-2007, IS 875 (Part I, II, IV), IS 1893-2002, AISC 360 (16 & 10) and FEMA 440 have been used. Part of this study also aims at comparing the response of these frames when subjected to near field and far field earthquakes. It can be concluded from the results that the post yield performance of the composite frame is superior to that of the steel frame when seismically excited.

In this study, a structural profiling of equid alphaherpesvirus 1 (EHV-1) transcriptome was carried out using next-generation (Illumina) and third-generation (Oxford Nanopore Technologies) sequencing platforms. We annotated the canonical mRNA molecules and their isoforms, including transcript start and end site isoforms, and splice variants. Additionally, a number of putative 5′-truncated mRNAs containing shorter in-frame ORFs were detected. We also demonstrated that EHV-1 produces a high number of non-coding transcripts, including antisense and intergenic RNAs. One of the most remarkable features of the EHV-1 is the generation of abundant fusion transcripts some of which encoding chimeric polypeptides. We observed a higher number of splicing and transcriptional overlaps than in related viruses. Additionally, we found that many upstream genes of tandem gene clusters have their own transcript end sites (TESs) besides the co-terminal TESs, which is rare in other alphaherpesviruses. We show here that the replication origins (OriS and OriL) of the virus are co-localized with promoter sequences and overlap with specific RNA molecules. Furthermore, we discovered a novel non-coding RNA (designated as NOIR) that overlaps the 5′-ends of the longer transcript variants encoded by the two main transactivator genes ORF64 and 65 bracketing the OriL. These all suggest the existence of a central regulatory system which controls the genome-wide transcription and the replication through a mechanism based on the interference between the machineries carrying out the synthesis of DNA and RNA.

This study aims to explore the link between public investment and private investment in South Africa, using time series data spanning 40 years (1980–2020). Private investment is subdivided into credit to private sector (CPS) and foreign direct investment (FDI). Several econometric methodologies were used in the study, including the unit root test, cointegration test, and Error Correction Method (ECM). The Phillips-Perron (PP) test results point out that all the variables are stationary at levels with the exception of public investment (PI) which is stationary at first difference. The co-integration test reveals that the variables have a long-run equilibrium relationship. According to the findings of the ECM, public investment has a negative relationship with private investment (as measured by credit to private sector and foreign direct investment). The conclusion implies that in South Africa, public investment crowds out private investment. Other results revealed that, RGDP crowds in credit to private sector while crowding out foreign direct investment. Finally, the ECM findings show that government consumption expenditure crowds out credit to private sector and foreign direct investment. The residuals are homoskedastic and show no serial correlation, indicating that the model is adequate, according to the test for adequacy.

This paper presents an approach to the vibration analysis of axially functionally graded non-prismatic Timoshenko beams (AFGNPTB) using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, shear moduli, and mass density) of axially functionally graded beams vary along the longitudinal axis. The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFGNPTB was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFGNPTB, considering the damping. The results obtained in this study showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

In this paper, an offshore airborne wind energy (AWE) farm consisting of three non-reversing pumping mode AWE systems is modelled and simulated. The AWE systems employ permanent magnet synchronous generators (PMSG). A direct interconnection technique is developed and implemented for AWE systems. This method is a new approach invented for interconnecting offshore wind turbines with the least number of required offshore-based power electronic converters. The direct interconnection technique can be beneficial in improving the economy and reliability of marine airborne wind energy systems. The performance and interactions of the directly interconnected generators inside the energy farm internal power grid are investigated. The results of the study conducted in this paper, show the directly interconnected AWE systems can exhibit a poor load balance and significant reactive power exchange which must be addressed. Power control strategies for controlling the active and reactive power of the AWE farm are designed, implemented, and promising results are discussed in this paper.

The article investigates the impact of the Environmental, Social, and Governance (ESG) criteria on the current tax systems worldwide. The ESG principles, although yet to be codified in hard law in most countries, are gaining increasing prominence in shaping business practices and policies. The article explores how these principles might influence the interpretation and application of existing tax rules, even without explicit legal mandates. It delves into four key areas where ESG considerations could play a significant role: the calculation of business income, transfer pricing regulations, the application of anti-avoidance rules, and the interpretation of the "business purpose" test. It argues that ESG principles, by redefining the purpose of a business beyond mere profit maximisation, could lead to a broader understanding of deductible costs, influence transfer pricing decisions, and impact the application of anti-avoidance measures. It concludes by emphasising the potential of ESG principles to shape the future of taxation, promoting a more sustainable and equitable approach to economic growth.

This study comprehensively evaluates the DNA/RNA Defend Pro (DRDP) sample collection buffer designed to inactivate and stabilize patient samples. The primary objectives encompassed assessing DRDP's efficacy in ensuring sample stability, facilitating extraction-free polymerase chain reaction (PCR), and ensuring compatibility with rapid antigen testing.Ninety-five diagnostic nasopharyngeal swab samples tested for influenza A/B, RSV A/B, and/or SARS-CoV-2 were diluted 1/10 with DRDP and anonymized. Stability testing involved incubating 31 positive samples at 4 °C, 20 °C, and 37 °C for 7 days, with regular extraction-free nucleic acid amplification testing (NAAT).Results demonstrated that DRDP guaranteed viral RNA stability at all temperatures for influenza, SARS-CoV-2 and RSV showing stability up to 7 days at 4 °C. DRDP-diluted samples exhibited robust compatibility with direct PCR, as 72 out of 88 samples positive for cobas Liat also tested positive for direct PCR. Non-concordant results could be explained by the 200-fold lower input in the extraction-free NAAT.Compared to NAAT, rapid antigen testing demonstrated lower sensitivity, as expected, while maintaining perfect specificity. Clear cutoffs between positive and negative rapid antigen testing results were observed in both cobas Liat and direct PCR analyses, validating DRDP's compatibility with these techniques. In conclusion, DRDP is an effective stabilizing medium compatible with direct PCR and rapid antigen testing and shows great potential for optimizing diagnostic processes, particularly in resource-limited or time-sensitive scenarios.

Mathematical modeling is the most important tool for constructing the theory of different kinds of two-phase flows. The review is devoted to the analysis of the advent of the approach of mathematical modeling of two-phase flows, where solid particles act mainly as the dispersed phase. The main problems and features of the study of gas-solid two-phase flows are excluded. The main characteristics of gas flows with solid particles are given and the classification of two-phase flows is developed on their basis. The Lagrangian and Euler approaches to modeling the motion of a dispersed phase (particles) are described. Much attention is paid to the consideration of numerical simulation methods that describe descriptions of turbulent gas flow at different hierarchical levels (RANS, LES, DNS), different levels of description of interphase interactions (one-way coupling (OWC), two-way coupling (TWC) and four-way coupling (FWC)), as well as at different levels of interface resolution (partial-point (PP) and particle-resolved (PR)). Excluded are examples of some studies carried out on the basis of the identified approaches, as well as their exclusion for mathematical modeling of various classes of gas-solid two-phase flows.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

This paper presents an approach to the vibration analysis of axially functionally graded (AFG) non-prismatic Euler-Bernoulli beams using the finite difference method (FDM). The characteristics (cross-sectional area, moment of inertia, elastic moduli, and mass density) of AFG beams vary along the longitudinal axis. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, differential equations were formulated with finite differences, and additional points were introduced at the beam’s ends and at positions of discontinuity (supports, hinges, springs, concentrated mass, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. Vibration analysis of AFG non-prismatic Euler-Bernoulli beams was conducted with this model, and natural frequencies were determined. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of AFG non-prismatic Euler-Bernoulli beams, considering the damping. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was always increased through a grid refinement.

Background: Objectives. The objective of this study was to compare the efficacy of direct current stimulation (DCS) applied at the transcranial, suboccipital and spinal level on experimental sensory modalities and pain outcome measures in healthy subjects. The hypothesis of this study was that systematic analysis of the efficacy of DCS on modulating evoked thermal and mechanical pain modalities and mechanisms such as endogenous pain modulation in healthy individuals would reveal sensitive outcome measures help develop this technique for the control of chronic pain. Materials and Methods. Database searches were conducted up to December 2019 for randomized controlled trials that performed sham-controlled DCS of experimental sensory modalities and pain outcomes following transcranial, suboccipital and spinal locations in healthy participants. Standardized mean differences with 95% confidence intervals were calculated for sensory modalities, including random-effect metanalysis. Results: Thirty-one studies were included for analysis (647 participants). A significant decrease in pain intensity for active vs sham transcranial stimulation was identified for pain intensity (n=158; SMD=0.79; 95% CI=0.56 to 1.02), a significant increase in heat pain threshold (n=222; SMD=1.16; 95% CI=0.95 to 1.37), and a significant increase in cold pain threshold (n = 155; SMD = 0.77, 95% CI 0.53 to 1.01). No significant modulation of pressure pain threshold was identified with DCS and only a limited number of studies focused on experimental pain modulation following neuromodulation at the suboccipital or spinal level. Conclusions: These results show significant transcranial DCS neuromodulation of pain intensity and on thermal pain modalities. Future studies should focus on endogenous pain and sensory modality modulation with sham-controlled DCS applied at transcranial, suboccipital and spinal locations.

Thin Slab Casting and Directing Rolling (TSCDR) has become a major process for flat- rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement resulting in some large grains persist in the final microstructure. In order to achieve excellent Ductile to Brittle Transaction (DBTT) and Drop Weight Tear Test (DWTT) properties in thicker gauge high strength low alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspective including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing new alloy with two phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

3D meso-scale structures that can reach up to centimeters in overall size but retain micro- or nano-features, proved to be promising in various science fields ranging from micro-mechanical metamaterials to photonics and bio-medical scaffolds. In this work we present synchronization of the linear and galvano scanners for efficient femtosecond 3D optical printing of objects at the meso-scale (from sub-μm to sub-cm spanning five orders of magnitude). In such configuration the linear stages provide stitch-free structuring at nearly limitless (up to tens-of-cm) working area, while galvo-scanners allow to achieve translation velocities in the range of mm/s-cm/s without sacrificing nano-scale positioning accuracy and preserving undistorted shape of the final print. The principle behind this approach is demonstrated, proving its inherent advantages in comparison to separate use of only linear stages or scanners. The printing rate is calculated in terms voxels/s, showcasing the capability to maintain an optimal feature size while increasing throughput. Full capabilities of this approach are demonstrated by fabricating structures that reach millimeters in size but still retain μm-scale features: scaffolds for cell growth, microlenses and photonic crystals. All this is combined into a benchmark structure: a meso-butterfly. Provided results show that synchronization of two scan modes is crucial for the end goal of industrial-scale implementation of this technology and makes the laser printing well aligned with similar approaches in nanofabrication by electron and ion beams.

Visualization of volumetric data holds great importance, particularly in medical and biomedical applications. Various imaging techniques, such as FMRI and 3D microscopy, are employed to generate volumetric data, used in medical practice, research, and teaching. Commonly utilized tools like 3D Slicer, Fiji, and MATLAB ® aid in rendering and analyzing 3D images. However, these tools may lack comprehensive rendering functionality and face challenges in handling computational demands as data sizes grow. To address these limitations, this work introduces a GPU-supported renderer with a MATLAB ® interface. This solution gives the user flexible control over rendering parameters and optimizes data transfer through a memory management system. By leveraging the computational power of NVIDIA GPUs, the renderer enables complex and high-quality renderings, enhancing speed and efficiency. It therefore facilitates the analysis and visualization of volumetric data within an integrated environment, namely MATLAB ®, streamlining their workflows. This advancement provides valuable opportunities for researchers and medical professionals to explore and comprehend volumetric data effectively.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

Transcranial direct current stimulation (tDCS) is acknowledged for its non-invasive modulation of neuronal activity in psychiatric disorders. However, its application in insomnia research yields varied outcomes depending on different tDCS types and patient conditions. Our primary objective is to elucidate its efficiency and uncover the underlying mechanisms in insomnia treatment. We hypothesized that anodal prefrontal cortex stimulation activates glutaminergic projections from the infralimbic cortex (IL) to ventrolateral preoptic area (VLPO) to promote sleep. After administering 0.06 mA of electrical currents for 8 minutes, our results indicate significant non-rapid eye movement (NREM) enhancement in naïve mice within the initial 3 hours post-stimulation, persisting up to 16-24 hours. In the insomnia group, tDCS enhanced NREM sleep bout numbers during acute stress response and improved NREM and REM sleep duration in subsequent acute insomnia. Sleep quality, assessed through NREM delta powers, remains unaffected. Interference of the IL-VLPO pathway, utilizing designer receptors exclusively activated by designer drugs (DREADDs) with the cre-DIO system, partially blocked tDCS's sleep improvement in stress-induced insomnia. This study elucidated that the activation of the IL-VLPO pathway mediates tDCS's effect on stress-induced insomnia. These findings support the understanding of tDCS effects on sleep disturbances, providing valuable insights for future research and clinical applications in sleep therapy.

The article presents an induction generator connected to the power grid using the AC / DC / AC converter and LCL coupling filter. In the converter, both from the generator side and from the power grid side, three-level inverters were used. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field Oriented Control (DFOC) method. At the same time, voltage control has been used for this solution. The MPPT algorithm has been extended to include the variable pitch range of the wind turbine blades. The active voltage balancing circuit has been used in the inverter DC voltage circuit. In the control system of the grid converter with an LCL filter, the number of measurements was limited to the measurement of power grid currents and voltages. Synchronization of control from the power grid side is ensured by the use of a PLL loop with the system of preliminary suppression of undesired harmonics (CDSC).

Chikungunya virus (CHIKV) is a mosquito-transmitted alphavirus that has re-emerged in recent decades, causing large-scale epidemics in many parts of the world. CHIKV infection leads to a febrile disease known as chikungunya fever (CHIKF), which is characterised by severe joint pain and myalgia. As many patients develop a painful chronic stage and neither antiviral drugs nor vaccines are available, the development of a potent CHIKV inhibiting drug is crucial for CHIKF treatment. A comprehensive summary of current antiviral research and development of small-molecule inhibitor against CHIKV is presented in this review. We highlight different approaches used for the identification of such compounds and further discuss the identification and application of promising viral and host targets.

The present paper investigates the effect of poverty on foreign direct investment (FDI) inflows in developing countries. It complements the important extant literature on the effect of FDI inflows on poverty by examining the issue the other way around. The analysis is conducted using a sample of 117 countries over the period 1980-2017, and the two-step system Generalized Methods of Moments (GMM) technique. It has relied on two indicators of poverty, namely poverty headcount ratio and poverty gap. Findings indicate that over the full sample, poverty influences negatively FDI inflows, including through its adverse effect on human capital (that is, both education and health). Unsurprisingly, low-income countries (considered as poorest countries in the full sample) experience a higher negative effect of poverty on FDI inflows than other countries. On another note, participation in international trade matters for the effect of poverty on FDI inflows. In fact, an increase in poverty levels results in lower FDI inflows in countries that experience low workers' productivity, a less developed financial sector, and a low level of infrastructure development. Furthermore, the effect of poverty on FDI inflows does not depend on the prevailing economic growth rate. Finally, the analysis has revealed the existence of a non-linear effect of poverty on FDI inflows for the poverty headcount indicator, but not for the poverty gap indicator. The non-linear effect of poverty headcount on FDI inflows is such that a rise in poverty headcount ratio results in lower FDI inflows, but an additional increase in poverty more than further discourages FDI inflows. The conclusion discusses the implications of these findings.

Direct Behavior Rating (DBR) as a behavioral progress monitoring tool can be designed as longitudinal assessment with only short intervals between measurement points. The reliability of these instruments has been evaluated mostly in observational studies with small samples based on generalizability theory. However, for standardized use in the pedagogical field, a larger and broader sample is required in order to assess measurement invariance between different participant groups and over time. Therefore, we constructed a DBR with multiple items to measure the occurrence of specific externalizing and internalizing student classroom behaviors on a Likert scale (1 = never to 7 = always). In a pilot study, two trained raters observed 16 primary school students and rated the student behavior over all items with a satisfactory reliability. In the main study, 108 regular primary school students, 97 regular secondary school students and 14 students in a clinical setting were rated daily over one week (five measurement points). IRT analyses confirmed the instrument’s technical adequacy, and latent growth models demonstrated the instrument’s stability over time. Further development of the instrument and study designs to implement DBRs are discussed.

The lightcone gauge is a set of what are called the observational coordinates adapted to our past lightcone. We develop this gauge by producing a perturbed spacetime metric that describes the geometry of our past lightcone where observations are usually obtained. We connect the produced observational metric to the perturbed Friedmann-Lema\^itre-Robertson-Walker metric in the standard general gauge or what is the so-called 1+3 gauge. We derive the relations between these perturbations of spacetime in the observational coordinates and those perturbations in the standard metric approach, as well as the dynamical equations for the perturbations in observational coordinates. We also calculate the observables in the lightcone gauge and re-derive them in terms of Bardeen potentials to first order. A verification is made of the observables in the perturbed lightcone gauge with those in the standard gauge. The advantage of the method developed is that the observable relations are simpler than in the standard formalism, and they are expressed in terms of the metric components which in principle are measurable. We use the perturbed lightcone gauge in galaxy surveys and the calculations of galaxy number density contrast. The significance of the new gauge is that by considering the null-like light propagations the calculations are much simpler due to the non-consideration of the angular deviations.

Weed competitive ability (WCA) is a desirable key trait for the improvement of grain yield under direct-seeded rice (DSR) and the aerobic rice ecosystem. The present study targeted screening of 167 introgression lines (ILs) of a Green Super Rice (GSR) IR2-6 population derived from a cross between Weed Tolerant Rice 1 (WTR1) as the recipient parent and Y134 as the donor parent developed at IRRI for weed competitiveness in screen house conditions (SHC). The ILs were phenotyped for WCA traits such as early seed germination (ESG) and early seedling vigor (ESV) in Petri dishes and pot experiment conditions. The results of phenotypic variance revealed ESG-related traits, especially first germination count (1st GC) that positively correlated with second germination count (2nd GC), germination percentage (GP), total dry weight (TDW), total fresh weight (TFW), and vigor index (VI-1), whereas, in ESV, all the traits were positively correlated with each other except for three traits: root dry weight (RDW), 1st GC, and GP-2. The ESG and ESV traits are vital for weed competitiveness. A 6K SNP array was used to study the genetic association for the WCA traits. Forty-four QTLs for WCA traits were mapped on all chromosomes (except on chromosomes 4 and 8) through single marker analysis (SMA). Out of 44 QTLs, 29 were associated with ESG traits and 15 with ESV traits, with LOD scores of 2.93 to 8.03 and 2.93 to 5.04 and explained phenotypic variance ranging from 7.85% to 19.9% and from 7.85% to 13.2%, respectively. However, 31 QTLs were contributed by a negative additive allele from Y134, whereas a positive additive allele was contributed by WTR1 in 13 QTLs. Among them, two QTL hotspot regions were mapped on chromosome 11 (24.7-27.9 Mb) and chromosome 12 (14.8-17.4 Mb). The majority of the QTLs related to WCA traits were grouped into two QTL hotspots: QTL hotspot-I (qAFW11.1, qFC11.1, qFC11.2, qSC11.1, qGP-111.1, qGP-111.2, qTFGS11.1, qVI-111.1, and qVI-111.2) and QTL hotspot-II (qFC12.1, qFC12.2, qSC12.1, qFC12.2, qGP-112.1, qGP-112.2, qTFGS12.1, qTFGS12.2, qVI-112.1, qIV12.2, qFC12.1, and qGC12.2), and a few of them were co-localized on chromosomes 11 and 12. Further, we fine-tuned in the genomic regions of QTL hotspots and identified a total of 13 putative candidate genes on chromosomes 11 and 12 collectively. The present study is the first report on the genetic basis of WCA-related traits and the co-localized QTLs, which could be highly valuable in future breeding programs aiming to improve WCA in rice.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

A specialized microenvironment in the bone marrow, composed of stromal cells including mesenchymal stem cells (MSCs), support hematopoietic stem cells (HSCs) self-renewal and differentiation but also regulates leukemia development and progression. The reciprocal direct interaction between MSCs and CD34+ HSCs under physiological and pathological conditions has not been well characterized yet. Here, we established a direct co-culture model between MSCs and CD34+ HSCs or MSCs and acute myeloid leukemia cells (THP-1, Molm-13, and primary cells from patients) to study cell-cell communication. Following MSCs-CD34+ HSCs co-culture, the expression of adhesion markers N-cadherin and connexin 43 increased in both cell types, forming gap junction channels. Moreover, the clonogenic potential of CD34+ HSCs was increased. However, direct contact of acute myeloid leukemia cells with MSCs reduced the expression levels of connexin 43 and N-cadherin in MSCs. The impairment in gap junction formation could be ascertained to a defect in the acute myeloid leukemia derived MSCs. Interestingly, CD34+ HSCs and acute myeloid leukemia cell lines restrained MSCs from engaging into osteoblastic differentiation upon prolonged direct cell-cell contact. In conclusion, under physiological conditions, connexin 43 and N-cadherin interaction preserves stemness of both CD34+ HSCs and MSCs, a process that is compromised in acute myeloid leukemia, pointing out to the possible role of gap junctions in modulating stemness.

Pain is a multifaceted multisystem disorder that adversely affects neuro-psychological processes. This study compares the effectiveness of central-stimulation (tDCS) and peripheral-stimulation (TENS) in pain-inhibition during a cognitive-task in healthy volunteers and to observe potential neuro-cognitive improvements. Healthy eighty volunteers went through a complete experimental protocol comprising pain-induction (CPT), administration of tDCS/TENS, EEG-data acquisition, and cognitive assessments. The protocol for this study is categorized into 04-groups: G1(Control), G2(TENS), G3(Anodal-tDCS), and G4(Cathodal-tDCS). Paired t-tests (p

The broad acceptance of electromobility depends heavily on the performance and service life of the battery technology used. Lithium-ion battery technology is currently the most promising energy storage technology for mobile applications, but the performance and capacity of the cells is extremely temperature sensitive. Especially in these new complex and powerful applications there is a significant need for thermal management. Depending on the ambient conditions, part of the effective battery energy must therefore be used to temper the system. So far, mainly active components have been used for this task. This not only reduces the overall efficiency, but also increases the weight, volume and maintenance requirements of the system. In the present work, an alternative battery temperature management system (BTMS) was developed. A concept based on latent heat storage materials was created, which uses the advantages of thermal energy storage and the design freedom of additive manufacturing technology, and its suitability for use in battery applications was checked. On the one hand, the use of systems for storing thermal energy was researched and, on the other hand, an innovative cooling concept was created considering new production possibilities.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

Transcranial direct current stimulation (tDCS) over the left Inferior Frontal Gyrus (IFG) was found to improve apraxia of speech (AOS) in post-stroke aphasia, speech fluency in adults who stutter, naming and spelling in primary progressive (PPA). This paper aims to determine whether tDCS over the left IFG coupled with AOS therapy improves speech fluency in patients with PPA more than sham. Eight patients with non-fluent PPA with AOS symptoms received either active or sham tDCS, along with speech therapy for 15 weekday sessions. Speech therapy consisted of repetition of increasing syllable-length words. Evaluations took place before, immediately after, and two months post-intervention. Words were segmented into vowels and consonants and the duration of each vowel and consonant was measured. Segmental duration was significantly shorter after tDCS than sham for both consonants and vowels. tDCS gains generalized to untrained words. The effects of tDCS sustained over two months post-treatment in trained words. Taken together, these results demonstrate that the tDCS over the left IFG facilitates speech production by reducing segmental duration. The results provide preliminary evidence that tDCS can maximize efficacy of speech therapy in non-fluent PPA with AOS.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

Background/Objectives: Post traumatic growth (PTG) has the potential to draw positive consequences from trauma. Hence, the interest of finding ways to promote PTG. Research has identified an attentional bias towards positive resilience-related words (e.g., “persistence”, “purpose”) in university students who report high PTG after experiencing adversities. Although people can respond to these experiences by showing low PTG, this bias seems to help with their struggle by making purposeful contents more accessible. Therefore, boosting attentional bias towards positive resilience-related words could help people with low PTG. Methods: In this study, the participants were thirty-six university students who had experienced bullying before entering university. Using a Stroop emotional task, they identified the color of resilience and neutral words, either positive or negative, before and after being submitted to transcranial direct current stimulation. Stimulation was targeted at the right temporal area involved in intentionality processing. Results: In the anodal condition, the results support a stimulation effect on the resilience attentional bias that could benefit participants with low PTG. A significant moderation of approach motivation for this effect was also found. Specifically, only when participants had medium or high approach motivation, did stimulation boost the attentional bias in students with low PTG. Conclusions: These results support that tDCS stimulation in this brain area is effective in enhancing resilience attentional bias in low PTG students. However, for this effect to occur it is necessary to have approach motivation, which is motivation related to goals.

Purpose: This integrated review aims to identify and analyze the multifactorial contributors to the longevity of direct restorations, focusing on tooth-, patient-, and dentist-related factors. Materials and Methods: A literature search was performed using an electronic database, PubMed/Medline, Web of Science, and Scopus, between 1980 and 2024. Titles and abstracts of papers that evaluated aspects categorized into tooth-related, patient-related, and dentist-related factors influencing restoration failure were selected and screened. Full-text assessments were conducted, and the extracted data were compiled, summarized, and synthesized. The reference lists of the collected papers were also screened, and relevant citations were included in this review. Data were gathered from clinical and laboratorial studies, systematic reviews, and meta-analyses to provide a comprehensive understanding of restoration longevity. Results: Among the tooth-related factors, multiple-surface restorations, deep margins, tooth location, and tooth vitality significantly impact restoration survival. Patient-related factors such as medical conditions, risk predictors of caries, age, sex, parafunctional habits, smoking, periodontal health, number of restorations, and socioeconomic status all play crucial roles. Regarding dentist-related factors, the decision-making process, age, experience, and dentist manual dexterity are vital aspects. Furthermore, the technique used, including isolation methods for moisture control, as well as the type of dental practice (large group vs. small practice), notably influenced the restoration survival. Conclusions: The longevity of dental restorations is influenced by a complex interplay of tooth-related, patient-related, and dentist-related factors. Strategies to improve restoration outcomes should consider all these multifactorial contributors. Continuing professional education, diligent patient guidance on the factors that influence restoration survival, careful material selection and restorative technique, and tailored individual treatment are crucial factors to reduce failure rates and improve the lifespan of restorations.

Cognitive impairment is a condition which affects aging patient populations and is becoming more prevalent as the geriatric population expands. It is categorized by the extent of cognitive decline, memory loss, functional abilities, and the capability to perform daily tasks. Based on the degree of impairment, it is classified as mild cognitive impairment or dementia. Considering the debilitating nature of cognitive decline and its impact on quality of life, prevention is key. In addition, given the gradual progression of the underlying causes of cognitive decline, early diagnosis and appropriate management has the potential to offer clinical advantages and better patient outcomes. Management options discussed vary from pharmaceutical regimens to neurosurgical interventions, with differing outcomes based on etiology of cognitive impairment.

This article investigated the Automatic Generation Control(AGC) of multi-area multi-source interconnected systems with hydropower plants, thermal power plants, and wind energy. Adaptive Neuro-fuzzy controller integrated with the cascaded proportional-integral-derivative with filter (PIDF-PIDF) is a new cascaded controller (ANF-PIDF-PIDF) that has been presented as a secondary controller for applied hybrid power systems. The recent Skill Optimization Algorithm (SOA) is employed to optimize PIDF- PIDF controller parameter gains and the Adaptive Neuro-Fuzzy controller's inputs and output scaling factors. SOA is used to update the controller parameters with integral square error (ISE) employed as the objective function. A 1% step load disturbance was considered simultaneously in all three areas. The controller's performance is evaluated and compared with and without considering the effects of wind energy sources and non-linearity for ANF-PIDF-PIDF, PIDF-PIDF, and PIDF and it was determined that the ANF-PIDF-PIDF was the most efficient. The dynamic system performance is also compared with parallel high voltage direct current (HVDC) tie-lines. The investigation clearly shows that incorporating HVDC tie-line with multi-area, multi-source provides better dynamic performance in maximum amplitude, oscillation, and settling time. Additionally, sensitivity analysis is done and the optimum controller gains does not need to be reset to uncertain values in system loading conditions. All simulation results were evaluated using MATLAB 2016b.

Increased exposure to artificial light at night can affect human health including disruption of melatonin production and circadian rhythms and extend to increased risks of hormonal cancers and other serious diseases. In addition, multiple negative impacts on fauna and flora are well documented, and it is a matter of fact that artificial light at night is a nuisance for ground-based astronomy. These impacts are frequently linked to the colour of the light or more specifically to its spectral content. Artificial light at night is often mapped by using space borne sensors, but most of them are panchromatic and thus insensitive to the colour. In this paper, we suggest a method that allows high resolution mapping of the Artificial light at night by using ground-based measurements with the LANcube system. The device separates the light detected in four bands (Red, Green, Blue, and Clear) and provides this information for six faces of a cube. We found relationships between the LANcube’s colour ratios and 1- the Melatonin Suppression Index, 2- the StarLight Index and 3- the Induced Photosynthesis Index. We show how such relationships combined with data acquisition from a LANcube positioned on the top of a car can be used to produce spectral indices maps of a whole city in a few hours.

Background and Aims: Sustained virologic response (SVR) lead to the decrease of portal hypertension, the regression of fibrosis, the improvement of the hepatic synthesis of procoagulant and anticoagulant factors. We aimed to assess the influence of SVR on coagulation parameters in HCV cirrhotic patients treated with DAAs. Methods: We performed a prospective study in the Institute of Gastroenterology and Hepatology Iasi, Romania, between January 2022 and February 2024. We included patients diagnosed with compensated and decompensated HCV-related liver cirrhosis, treated with direct antivirals (PrOD ± RBV or SOF/LED ± RBV) for 12/24 weeks. Blood samples for biochemical, immunological and coagulation tests were collected at baseline, EOT and SVR12/24. Results: We analyzed a group of 52 patients with HCV-related liver cirrhosis, predominantly female (68.0%), the degree of severity of cirrhosis placed the patients mainly in Child-Pugh classes B (40%) and C (36%). All patients achieved SVR. The MELD score decrease at EOT (13.48 ± 4.273; p =0.001), and SVR (9.88 ± 2.774; p = 0.000), compared to baseline (14.92 ± 4.707). Fibroscan values decreased at SVR (17.596 ± 3.7276; p = 0.000) compared to baseline (26.068 ± 7.0954). For all common coagulation parameters (platelets, INR, PT, fibrinogen, aPTT) there was a trend towards improvement during treatment, changes that were statistically significant for the majority of patients. Factor II low at baseline (75.40 ± 7.506), increases at EOT (87.40 ± 9.587), and later at SVR (99.12 ± 11.695; p = 0.000). FVIII values increased at baseline (175.52 ± 16.414) decrease at EOT (151.48 ± 13.703) and SVR (143.40 ± 13.937). FvW values decreased during treatment (146.84 ± 9.428 – baseline, 141.32 ± 9.690; p =0.000 – EOT, 126.68 ± 17.960 – SVR). In regards to the anticoagulant factors (PC, PS, ATIII), a significant improvement was brought on by SVR. Advanced stages of liver disease showed the most diminished FII activity, while at baseline and in Child-Pugh C patients we recorded the highest values of FVIII and FvW. Conclusions: Our study proved that the “reset” of the coagulopathy might be due to the improving of the liver function due to viral eradication secondary to AAD therapy.

The global steel industry is a major contributor to greenhouse gas emissions, and the adoption of green hydrogen in Direct Reduced Iron (DRI) production has the potential to significantly reduce CO2 emissions and support climate targets. This review explores the environmental, economic, technological, and social implications of using green hydrogen in DRI processes. The findings suggest that green hydrogen can reduce emissions by up to 90% compared to traditional methods, enhance energy security, and stimulate local economic development. However, high initial costs, energy efficiency concerns, and social acceptance issues remain significant barriers. The review also highlights the importance of integrating carbon capture and storage technologies, addressing logistical challenges, and considering the geopolitical implications of a shift towards green hydrogen. Green hydrogen presents a promising solution for decarbonising the steel industry but continued research, investment in infrastructure, and strategic planning are essential to overcome the challenges and drive widespread adoption.

Background: In Transcranial Direct Current Stimulation (tDCS) the injected current gets distributed across the brain areas. The motive is to stimulate the target region-of-interest (ROI), while minimizing the current in non-target ROIs. For this purpose, determining the appropriate current-dose for an individual is difficult. Aim: To introduce Dose-Target-Determination-Index (DTDI) to quantify the focality of tDCS and examine the dose-focality relationship in three different populations. Method: Here, we extended our previous toolbox i-SATA to the MNI reference space. After a tDCS montage is simulated for a current-dose, the i-SATA(MNI) computes the average (over voxels) current density for every region in the brain. DTDI is the ratio of average current density at target ROI to the ROI with maximum value (peak region). Ideally target ROI should be the peak region, so DTDI shall range from 0 to 1. Higher the value, the better the dose. We estimated the variation of DTDI within and across individuals using T1-weighted brain images of 45 males and females distributed equally across three age groups- (a) Young adults (20 ≥ x ˂ 40 years), (b) Mid adults (40 ≥ x ˂ 60 years), and (c) Older adults (60 ≥ x ˂ 80 years). DTDI’s were evaluated for the frontal montage with electrodes at F3 and right supra-orbital for three current doses 1mA, 2mA, and 3mA with the target ROI at left middle frontal gyrus. Result: As the dose is incremented, DTDI may show (a) increase, (b) decrease, and (c) no change across the individuals. The focality decreases with age and the decline is stronger in males. Higher current dose at older age can enhance the focality of stimulation. Conclusion: DTDI provides information on which tDCS current dose will optimize the focality of stimulation. DTDI recommended dose should be prioritised based on the age (> 40 years) and sex (especially males) of an individual. The toolbox i-SATA(MNI) is freely available.

Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

Electrical energy demand increase does evolve rapidly due to several socioeconomic factors such as industrialization, population growth, urbanization and of course the evolution of modern technologies in this 4th industrial revolution era. Such rapid increase in energy demand introduces a huge challenge in power system. Such has paved way for network operators to seek for alternative energy resources other than the conventional fossil fuel system. Hence, the penetration of renewable energy into the electricity supply mix has evolved rapidly in the past three decades. However, the grid system has to be well planned ahead to accommodate such increase in energy demand in the long run. Transmission Network Expansion Planning (TNEP) is a well ordered and profitable expansion of power facilities that meets the expected electric energy demand with an allowable degree of reliability. This paper proposes a TNEP model that minimises the network reinforcements, operational costs and costs of renewable energy penetrations, while satisfying the increase in demand. The problem is formulated as a mixed integer linear programming (MILP) problem. The developed model has been tested in several IEEE test systems in multi-period scenarios. The paper also carried out a detailed derivation of the new non-negative variables in terms of the power flow magnitudes, the bus voltage phase angles and the lines’ phase angles for proper mixed integer variables’ decomposition techniques. Moreover, this paper tends to provide additional recommendation in terms of which particular year (within 20 years of planning period) can the network operators install new line(s), new corridor(s) and/or additional generation capacity to the respective existing power networks. Such is achieved by running incremental periods simulations from base year through the planning horizon. The results show the efficacy of the developed model in solving the TNEP problem with a reduced and acceptable computation time even for large power grid system.

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.

Direct electron transfer (DET)-type bioelectrocatalysis, which couples electrode reactions and catalytic functions of redox enzymes without any redox mediator, is one of the most intriguing subjects studied over the past decades in the field of bioelectrochemistry. In order to realize the DET-type bioelectrocatalysis and to improve the performance, nanostructures of the electrode surface have to be carefully tuned for each enzyme. In addition, enzymes can also be tuned by protein engineering approach for the DET-type reaction. This review summarizes the resent progresses in this field of the research, while taking into consideration of the importance of nanostructure of electrodes as well as redox enzymes. Described are basic concepts and theoretical aspects of DET-type bioelectrocatalysis, significance of nanostructures as scaffolds for DET-type reactions, protein engineering approached for DET-type reactions, and concepts and facts of bidirectional DET-type reactions, from a cross-disciplinary viewpoint.

(1) Background: Transcription factors (TFs) are main regulators of eukaryotic gene expression. The cooperative binding of at least two TFs to genomic DNA is the widespread mechanism of transcription regulation. Massive analysis of co-occurrence of overrepresented pairs of motifs (composite elements, CEs) for different target TFs studied in ChIP-seq experiments can clarify the mechanisms of TF cooperation. (2) Methods: We focused on homotypic CEs representing the same motif models and considered only CEs with spacers. We improved the capability of the Motifs Co-Occurrence Tool (MCOT) to predict asymmetric homotypic CEs in which one of par-ticipating motifs has higher conservation than the other. We categorized the target TFs from the data of M. musculus ChIP-seq and A. thaliana ChIP-seq/DAP-seq according to the structure of DNA-binding domains (DBDs) into classes. (3) Results: For all TF classes the predominance of asymmetric CEs over both symmetric and those with no enrichment in both directions was re-vealed. Target TFs from classes Basic helix-loop-helix factors (bHLH) and Basic leucine zipper factors (bZIP) showed the highest fractions of datasets with asymmetric CEs. We showed that pioneer TFs, despite their DBD types, have a higher significance of asymmetry within homotyp-ic CEs compared to other TFs. (4) Conclusion: Asymmetry within homotypic CEs is a promising new feature decrypting the mechanisms of gene transcription regulation.

Abstract: A recent approach to radiotherapy for prostate cancer is the administration of high doses of radiation to the prostate while minimizing the risk of side effects. Thus, image-guided radiotherapy utilizes advanced imaging techniques and is a feasible strategy for increasing the radiation dose. New radioactive particles are another approach to achieving high doses and safe procedures. Prostate brachytherapy is currently considered as a combination therapy. Spacers are useful to protect adjacent organs, specifically the rectum, from excessive radiation exposure.

This paper presents an approach to the Kirchhoff-Love plate theory (KLPT) using the finite difference method (FDM). The KLPT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally in the case of KLPT, the finite difference approximations are derived based on the fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection surface. The FOPH is made for the fourth and third derivative of the deflection surface while the SOPH is made for its second and first derivative; this leads to a 13-point stencil for the governing equation. In addition, the boundary conditions and not the governing equations are applied at the plate edges. In this paper, the FOPH was made for all of the derivatives of the deflection surface; this led to a 25-point stencil for the governing equation. Furthermore, additional nodes were introduced at plate edges and at positions of discontinuity (continuous supports/hinges, incorporated beams, stiffeners, brutal change of stiffness, etc.), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at the plate edges and to satisfy the boundary and continuity conditions. First-order analysis, second-order analysis, buckling analysis, and vibration analysis of plates were conducted with this model. Moreover, plates of varying thickness and plates with stiffeners were analyzed. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. In first-order, second-order, buckling, and vibration analyses of rectangular plates, the results obtained in this paper were in good agreement with those of well-established methods, and the accuracy was increased through a grid refinement.

Apraxia of speech is a persistent speech motor disorder that affects speech intelligibility. Studies on speech motor disorders with transcranial Direct Current Stimulation (tDCS) have been mostly directed to post-stroke aphasia. Only a few tDCS studies have focused on apraxia of speech or childhood apraxia of speech (CAS), and no study has investigated individuals with CAS and people with trisomy 21 (T21, Down Syndrome). This study examined the effects of tDCS combined with a motor learning task in developmental apraxia of speech co-existing with T21 (ReBEC RBR-5435x9). The accuracy of speech sound production of nonsense words (NSWs) during Rapid Syllable Transition Training (ReST) under 10 sessions of anodal tDCS (1.5 mA, 25 cm) over the Broca’s area with cathode over the contralateral region was compared to 10 sessions of sham-tDCS and 4 control sessions in a 20-year-old male individual with T21 presenting moderate-severe childhood apraxia of speech (CAS). The accuracy for NSWs production progressively improved (gain 40%) under tDCS only (sham-tDCS and control sessions showed <20% gain). A decrease in speech severity from moderate-severe to mild-moderate indicated transfer effects in speech production. The speech accuracy under tDCS was correlated with Wernicke’s area activation (P3 current source density), which in turn, was correlated with the activation of the left supramarginal gyrus and the Sylvian Parietal Temporal Junction. Repetitive bihemispheric tDCS paired with ReST may have facilitated the speech sound acquisition in a young adult with T21 and CAS, possibly by recruiting brain regions required for the phonological working memory.

Early in the middle of the 1800s. Up until about 1900, the automotive land speed record 1 was held by an electrical vehicle. Unfortunately, internal combustion engine vehicles did not do 2 well in the market due to their high cost, limited speed, and short range in the 20th century, which 3 resulted in a global fall in their use as private motor vehicles. Since there are no fuel emissions into 4 the environment, there are important uses for electrical vehicles, Electric cars, or EVs, have a closed 5 circuit, cheap operating costs, no maintenance requirements, and excellent performance. The goal 6 of this project is to assess the current state of electric vehicles and the issues surrounding the global 7 advancement of electric vehicle technology. Because of the changing climate.8

The Van der Pol oscillator is a chaotic non-linear system. Small perturbations in initial conditions may result in wildly different trajectories. Because of its chaotic nature, controlling, or forcing, the behavior of a Van der Pol oscillator is difficult to achieve through traditional adaptive control methods. Connecting two Van der Pol oscillators together where the output of one oscillator, the driver, drives the behavior of its partner, the responder, is a proven technique for controlling the Van der Pol oscillator. Deterministic AI (DAI) is an adaptive feedback control method that leverages the known physics of the Van der Pol system to learn optimal system parameters for the forcing function. We assessed the performance of DAI employing three different online parameter estimation algorithms. Our evaluation criteria include mean absolute error (MAE) between the target trajectory and the response oscillator trajectory over time. RLS with exponential forgetting (RLS-EF) had the lowest MAE overall, with a 2.46% reduction in error. However, another method was notable. Least Mean Squares with normalized gradient adaptation (LMS-NG) had worse initial error in the first 10% of the simulation, but after that point had consistently better performance. We found that over the last 90% of the simulation, DAI with LMS-NG had a 48.7% reduction in MAE compared to feedforward alone.

Building a new power plant to address the growing demand for power due to population concentration in the metropolitan area is one of the world's major concerns. However, since a large power plant can not be located around the city due to burden of economic cost, building power plant outside metropolitan and cities is necessary. Therefore, new power generation facilities are promoting policies to provide distributed generator(DG) with a small capacity relatively near the metropolitan. When the DG (photovoltaic, wind farm, etc.) is connected with the grid using medium voltage direct current (MVDC) system, voltage sourced converter(VSC) should supply reactive power to the grid, because of fault ride through(FRT) operation in grid fault. If the voltage drop is severe, the converter should be disconnected from the grid immediately without supplying the reactive power, resulting in a considerable economic loss. In general, superconducting fault current limiter(SFCL) is introduced as a measure to enhance FRT capability. In this paper, we use trigger type SFCL which protects superconducting element and reduces low voltage. On the other hand, the active power unbalance of the DC-link and the DC voltage rise due to the reactive power supply of the grid-side converter. The rise of the DC voltage causes the P (active power), Q (reactive power) control of the converter to deviate, causing malfunction and damage of the DC equipment. Therefore, the rise of the DC voltage must be prevented. In this paper, we consider the suppression the DC voltage rising caused by the FRT operation through the active power tracking control (APTC).

This review focuses on the evidence for neurotherapeutics for Attention Deficit Hyperactivity Disorder (ADHD). EEG-Neurofeedback has been tested for about 45 years with latest meta-analyses of randomised controlled trials (RCT) showing small/medium effects compared to non-active controls only. Three small studies piloted neurofeedback of frontal activations in ADHD using functional magnetic resonance imaging or near-infrared spectroscopy, finding no superior effects over control conditions. Brain stimulation has been applied to ADHD using mostly repetitive transcranial magnetic and direct current stimulation (rTMS/tDCS). rTMS has shown mostly negative findings on improving cognition or symptoms. Meta-analyses of tDCS studies targeting mostly dorsolateral prefrontal cortex show small effects on cognitive improvements with only two out of three studies showing clinical improvements. Trigeminal nerve stimulation has shown to improve ADHD symptoms with medium effect in one RCT. Modern neurotherapeutics are attractive due to their relative safety and potential neuroplastic effects. However, they need to be thoroughly tested for clinical and cognitive efficacy across settings and beyond core symptoms and for their potential for individualised treatment.

Despite great technical capabilities, the theory of non-contact temperature measurement is usually not fully applicable to the use of measuring instruments in practice. While black body calibrations are in practice well established and easy to accomplish, this calibration protocol is never fully applicable to measurements of real objects under real conditions. Currently, the best approximation to real world radiation thermometry is grey body radiation thermometry, which is supported by most measuring instruments to date. Nevertheless, the metrological requirements necessitate traceability, therefore real body radiation thermometry is required for temperature measurements of real bodies. This article documents the current state of temperature calculation algorithms for radiation-thermometers and the creation of a traceable model for radiation thermometry of real bodies that uses a digital twin model of the system of measurement to compensate for the loss of data, caused by spectral integration, which occurs when thermal radiation is absorbed on the active surface of the sensor. To solve this problem, a hybrid model with variable scalar inputs is proposed, in which the scalar input parameters are calculated to correspond to the system of measurement. The method for calculating the effective parameters is proposed and verified with the theoretical model of non-contact thermometry. The sum of effective instrumental parameters is presented for different temperatures to show that the rule of radiation thermometry of grey bodies, according to which the sum of instrumental emissivity and instrumental reflectivity equals to 1, does not hold in radiation thermometry for real bodies. Using the derived models of radiation thermometry, the uncertainty of radiation thermometry due to the uncertainty of spectral emissivity is analysed by simulated measurements along the temperature ranges of various radiation thermometers, enabling traceable non-contact temperature measurements with known measurement uncertainty under any known conditions.

The aim of this paper is to present a comprehensive overview of the main aims and scopes in screening of botanicals, a task which thin-layer chromatography (TLC) is on an everyday basis confronted with and engaged in. Stunning omnipresence of this modest analytical technique (both in its standard format (TLC) and the high-performance one (HPTLC), either hyphenated or not) for many analysts might at a first glance appear chaotic and random, with an auxiliary rather than leading role in research, and not capable of issuing meaningful final statements. Based on these reflections, our purpose is not to present a general review paper on TLC in screening of botanicals, but a blueprint rather (illustrated with a selection of practical examples), which highlights a sovereign and important role of TLC in accomplishing the following analytical tasks: (i) solving puzzles related to chemotaxonomy of plants, (ii) screening a wide spectrum of biological properties of plants, (iii) providing quality control of herbal medicines and alimentary and cosmetic products of biological origin, and (iv) tracing psychoactive plants under forensic surveillance.

The formation and propagation of cracks occurs through irreversible dislocation movements at notches, material defects and grain boundaries. Since this process is partly thermally controlled, the resistance to dislocation movements at low temperatures increases. This slows both fatigue initiation and fatigue crack propagation. From recent experimental data, it can be seen that fatigue crack growth is accelerated below the fatigue transition temperature (FTT) that correlates with the ductile-brittle transition temperature (DBTT) found by well-known fracture mechanics tests, i.e., Charpy impact, fracture toughness, and CTOD. Hence, this study investigates the relation between FTT and DBTT in S500 high-strength steel base material and welded joints at low temperatures using fatigue crack growth, fracture toughness tests as well as scanning electron microscopy. From the tests, an almost constant decrease in fatigue crack propagation rate is determined with decreasing test temperature even below the DBTT.

Background: Transcription factors (TFs) are main regulators of eukaryotic gene expression. The cooperative binding to genomic DNA of at least two TFs is the widespread mechanism of transcription regulation. Cooperating TFs can be revealed through the analysis of co-occurrence of their motifs. Methods: We applied Motifs Co-Occurrence Tool (MCOT) that predicted pairs of spaced or overlapped motifs (composite elements, CEs) for a single ChIP-seq dataset. We improved MCOT capability for prediction of asymmetric CEs with one of participating motifs possessing higher conservation than another does. Results: Analysis of 119 ChIP-seq datasets for 45 human TFs revealed that almost for all families of TFs the co-occurrence with an overlap between motifs of target TFs and more conserved partner motifs was significantly higher than that for less conserved partner motifs. The asymmetry toward partner TFs was the most clear for partner motifs of TFs from ETS family. Conclusion: Co-occurrence with an overlap of less conserved motif of a target TF and more conserved motifs of partner TFs explained a substantial portion of ChIP-seq data lacking conserved motifs of target TFs. Among other TF families, conservative motifs of TFs from ETS family were the most prone to mediate interaction of target TFs with its weak motifs in ChIP-seq.

A retrospective cohort study was performed to determine the likelihood of malignant stroke after mechanical thrombectomy via ASPECTS-PASS score(A-P score), a novel scoring system using ASPECT score and number of arterial-passes. This prediction score is designed to help clinicians take early measures. Malignant stroke is defined as a large MCA infarct with mass effect that develops during the first 5 days following presentation and is associated with approximately 80% mortality. Previous studies have shown an association of low ASPECTS and high number of passes with poor outcome.We performed a retrospective cohort analysis on 78 patients with anterior circulation stroke who underwent mechanical thrombectomy at our hospital. We analyzed the likelihood of developing malignant stroke post thrombectomy in the first 5 days following successful recanalization (TICI ≽ 2b). Malignant stroke is defined as severe symptoms secondary to edema as evidenced by midline shift, cistern engorgement, and hemorrhagic conversion with edema. Patients with ASPECTS of 0-5 were excluded. We used two variables to predict the outcome: ASPECT score and number-of-passes. We used the equation ASPECT score minus number-of-passes (A-P) to arrive at a single number to predict the risk of malignant stroke. A-P scoring scale ranged from 0-9. Our study showed a statistically significant inverse relationship of A-P score and risk of malignant stroke. Approximately 90% of patients with A-P score < 5 developed malignant stroke in our study. A-P score can help predict malignant stroke post thrombectomy even after successful recanalization. Thus, A-P score of ≤ 5 suggests very high risk. (A-P) Score can assist clinicians to take early measures, and thereby prevent worse outcomes.