We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

Based on collected power generation data associated with solar irradiance, PV system conversion efficiency and cell temperature, an hourly solar PV power estimation model by a parallel artificial neural network (ANN) and particle swarm optimization (PSO) algorithm is proposed. Weight matrices related to different seasons and geographic areas for estimation power generations have been trained by real measured operation data. The parallel PSO algorithm with heuristic global optimization technique assists the ANN training process to get near optimal solutions precisely. The accuracy and reliability of estimation is audited by actual details of photovoltaic power stations in various regions and scales. The results of estimation model can not only assist the electricity dispatcher to explicitly monitor the trend of solar power generation in different areas, but also coordinate with traditional power plants to meet load demand more accurately. The presented model will bring benefits to power dispatching for larger scales of intermittent and unstable solar power generation.

The provision requirement of 10% openings of the total floor area stated in the Uniform Building by Law 1984 Malaysia has been practiced by designers for building plan submission approval. However, the effectiveness of thermal performance in landed residential buildings, despite the imposition by the by-law, has never been empirically measured and proven. Although terraced houses in Malaysia have dominated 40.9% of the total property transaction in 2019, such mass production with typical designs hardly provides its occupants with thermal comfort due to the static outdoor air condition and lack of external windows, where the conventional ventilation technique does not work well, even for houses with an air well system. Consequently, the occupants need to rely on mechanical cooling, which is a high energy-consuming component contributing to outdoor heat dissipation and therefore urban heat island effect. Thus, encouraging more effective natural ventilation to eliminate excessive heat from the indoor environment is critical. Since most of the research focuses on simulation modelling lacking sufficient empirical validation, this paper drawing on field measurement investigates natural ventilation performance in terraced housing with an air well system. More importantly, the key concern as to what extent the current air well system serving as a ventilator is effective to provide better thermal performance in the single storey terraced house is to be addressed. By adopting an existing single storey air welled terrace house, the existing indoor environmental conditions and thermal performance were monitored and measured using scientific equipment, namely HOBO U12 air temperature and air humidity, the HOBO U12 anemometer and the Delta Ohm HD32.3 Wet Bulb Globe Temperature meter for a six-month duration. The findings show that the air temperature of the air well ranged from 27.48°C to 30.92°C, while the mean relative humidity were from 72.67% to 79.25%. The mean air temperature for a test room (single sided ventilation room) ranged from 28.04°C to 30.92°C with a relative humidity of 70.16% to 76%. These empirical findings are of importance, offering novel policy insights and suggestions to potentially revising the existing building code standard and by laws; since the minimum provision of 10% openings has been revealed to be less effective to provide a desired thermal performance and comfort, mandatory compliance with, and the necessity for, the bylaw requirement should be revisited and further studied.

Seed bank survival underpins plant population persistence but studies on seed bank trait-environment interactions are few. Changes in environmental conditions relevant to seed banks occur in desert ecosystems owing to solar energy development. We developed a conceptual model of seed bank survival to complement methodologies using in-situ seed bank packets. Using this framework, we quantified the seed bank survival of two closely related annual desert plant species, one rare (Eriophyllum mohavense) and one common (Eriophyllum wallacei) and the seed bank-environment interactions of these two species in the Mojave Desert within a system that emulates microhabitat variation associated with solar energy development. We tracked 4,860 seeds buried across 540 seed packets and found, averaged across both species, that seed bank survival was 21% and 6% for the first and second growing seasons, respectively. After two growing seasons, the rare annual had a significantly greater seed bank survival (10%) than the common annual (2%). Seed bank survival, across both species, was significantly greater in Shade (10%) microhabitats compared to Runoff (5%) microhabitats and Control microhabitats (3%). Our study confers insight into this early life-stage across rare and common congeners and their environmental interactions using a novel conceptual framework for seed bank survival.

Desalination accounts for 1% of the total global water consumption and is an energy-intensive process, with the majority of operational expenses attributed to energy consumption. Moreover, at present, a significant portion of the power comes from traditional fossil fuel-fired power plants and the greenhouse gas emissions associated with power production along with concentrated brine discharge from the process, pose a severe threat to the environment. Due to the dramatic impact of climate change, there is a major opportunity to develop sustainable desalination processes to combat the issues of brine discharge, greenhouse gas emissions along with a reduction in energy consumption per unit of freshwater produced. Nanotechnology can play a vital role to achieve specific energy consumption reduction as nanofluids application increases the overall heat transfer coefficient enabling the production of more water for the same size desalination plant. Furthermore, concentrated brine discharge harms the marine ecosystems, and hence, this problem must also be solved to support the objective of sustainable desalination. Several studies have been carried out in the past several years in the field of nanotechnology applications for desalination, brine treatment and the role of renewable energy in desalination. This paper aims to review the major advances in this field of nanotechnology for desalination. Furthermore, a hypothesis for developing an integrated solar thermal and nanofluid sustainable desalination system, based on the cyclic economy model is proposed.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus 13 voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ 14 constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources 15 on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar 16 PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed 17 using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of 18 simulation and statistical results of EO with other optimization techniques showed that EO is more effective 19 and superior.

A large body of evidence reports about the positive effects of physical activity in pathophysiological conditions associated with aging. Physical exercise, alone or in combination with other medical therapies, unquestionably causes reduction of symptoms in chronic non-transmissible diseases often leading to significant amelioration or complete healing. The molecular basis of this exciting outcome, however, remain largely obscure. Epigenetics, exploring at the interface between environmental signals and the remodelling of chromatin structure, promises to shed light on this intriguing matter possibly contributing to the identification of novel therapeutic targets. In this review, we shall focalize on the role of sirtuins (Sirts) a class III histone deacetylases (HDACs) which function has been frequently associated, often with a controversial role, to the pathogenesis of aging-associated pathophysiological conditions including cancer, cardiovascular, muscular, neurodegenerative, bones and respiratory diseases. Numerous studies, in fact, demonstrate that Sirt-dependent pathways are activated upon physical and cognitive exercises linking mitochondrial function, DNA structure remodelling and gene expression regulation to designed medical therapies leading to tangible beneficial outcomes. However, in similar conditions, other studies assign to sirtuins a negative pathophysiological role. In spite of this controversial effect, it is doubtless that studying sirtuins in chronic diseases might lead to an unprecedented improvement of life quality in the elderly.

In a recent paper, we extended previous studies on solar-terrestrial relationships by investigating the origin of the March 2012 heatwave in northeast USA. In the present study we check the possible relationship of solar activity with the early March 2012 bad weather in northeast Thrace, Greece. To this end, we examined data from various remote sensing instrumentation monitoring the Sun (SDO satellite), the Interplanetary Space (ACE satellite), the Earth’s magnetosphere (Earth based measurements, NOAA-19 satellite), the top of the clouds (TERRA and AQUA satellites) and the near ground atmosphere. Our comparative data analysis suggests that: (i) the winter-like weather (rainfall, fast winds, decreased temperature) in Thrace started on 6 March 2012, on the same day as the heatwave starting in USA, (ii) during the March 2012 winter-like event in Thrace (6-15 March), the ACE satellite recorded enhanced fluxes of solar energetic particles (SEPs), while SOHO and PAMELA recorded solar protons at very high energies (> 500 MeV), (iii) Thrace experienced particularly intense cyclonic circulation, during periods of magnetic storms on 8 - 10 and 12-13 March, which occurred after the arrival at ACE of two interplanetary shock waves, on March 8 and March 11, respectively, (iv) at the beginning of the two above mentioned periods large atmospheric electric fields were recorded, with values ranging between ~-2000V/m - ~1800V/m on 8 March, (v) the winter-like 8-10 March 2012 weather occurred after the detection of the main SEP event related with a coronal mass ejection released in the interplanetary space as a result of intense solar flare activity observed by SDO on 7 March 2012, (vi) the 8-10 March weather was related with a deep drop of ~630C in the cloud top temperature measured by MODIS/TERRA, which favors strong precipitation. Finally, we analyzed data from the electric power network in Thrace (~410N) and we found, for the first time sudden voltage changes of ~3.5kV in the electric grid in Greece, during the decay phase of the March 2012 superstorm. We discuss the winter-like March 2012 event in Thrace in terms of solar cosmic ray influence on the low troposphere mediated by positive NAO. Finally, we infer that the novel finding of the geomagnetic effects on the electric power grid in Thrace may open a new window into space weather applications research.

This paper defines the two main causes of global warming in the UK and seeks to cut climate change using green hydrogen made from renewable electricity sources. Combustion vehicles powered by fossil gasoline and diesel emit a third of UK climate-warming CO2 while buildings heated by natural gas provide a quarter. First, current UK grid problems are defined: Electricity grid, gas grid and petroleum grid. Then experiments on the private energy community of Keele University allow electrolysis demonstrations producing green hydrogen for buildings and vehicle refueling. Next, the model supply chain is planned and tested. Finally, experiments and calculations are outlined, analyzing the optimum system design criteria proposed. We conclude that economic green hydrogen can displace diesel and gasoline in vehicle transport, while also displacing natural gas for combined heat and power in buildings. In addition, the prospect in 2023 is that profits can now be made all along the green hydrogen supply chain, such that new businesses involved in clean communities can beat the National Grid monopoly and other large dominant fossil grid companies.

Fluorophores with a tetraphenylethylene (TPE) core are attracting increasing interest because of their aggregation-induced emission (AIE) behaviour, which makes them particularly suitable when dispersed in thin-layer films. We propose the synthesis and use of a novel TPE fluorophore (hereafter called TPE-BPAN) decorated with two dimethylamino push groups and a 4-biphenylacetonitrile pull moiety. In tetrahydrofuran solutions, TPE-BPAN showed a broad absorption spectrum, and an intense emission is observed when a non-solvent as water is added in amounts of 70% and above. We selected and synthetized five different polymer matrices for TPE-BPAN with decreasing polarity: a) poly(methylmetacrylate) homopolymer (PMMA); b), c), and d) three copolymers of methyl methacrylate and cyclohexyl methacrylate at different compositions (P(MMA-co-CHMA) 75:25, 50:50, 25:75 mol%); e) poly(cyclohexyl methacrylate) homopolymer (PCHMA). The presence of a less polar comonomer as cyclohexyl methacrylate appeared to enhance the emission behaviour of TPE-BPAN, which displayed the highest quantum yield (QY) in P(MMA-co-CHMA) 75:25 in all the range of concentration studied from 0.4 wt.% to 2.0 wt.%. Further reduction in polarity lowered QY to the values of PMMA films; also, lower adhesion to the glass and a marked fragility of the films were observed. Referring to the P(MMA-co-CHMA) 75:25 films, QY values decreased from over 40% at 0.4 wt.% to about 30% at 2.0 wt.%, which is still helpful for energy harvesting applications such as luminescent solar concentrators (LSC). LSC performances were not significantly affected by the matrix's lower polarity and resulted in around one-third of the state-of-the-art due to the lower QY of TPE-BPAN. The theoretical investigation on density functional theory (DFT) clarified the origin of the observed AIE and the role played by the environment in modulating the photophysical behaviour.

According to the Cosmological Principle the Universe is isotropic and no preferred direction would be seen by an observer that might be stationary with respect to the expanding cosmic fluid. However, because of observer’s partaking in the solar system peculiar motion, there would appear in some of the observed properties of the Cosmos a dipole anisotropy, which could in turn be exploited to determine the peculiar motion of the solar system. The dipole anisotropy in the Cosmic Microwave Background Radiation (CMBR) has given a peculiar velocity vector 370 km s−1 along l=264∘,b=48∘. However, some other dipoles, for instance, from the number counts, sky brightness or redshift distributions in large samples of distant Active Galactic Nuclei (AGNs), have yielded values of the peculiar velocity many times larger than that from the CMBR, though surprisingly, in all cases the directions agreed with the CMBR dipole. Here we determine our peculiar motion from a sample of 0.28 million AGNs, selected from the Mid Infra Red Active Galactic Nuclei (MIRAGN) sample comprising more than a million sources. From this, we find a peculiar velocity, which is more than four times the CMBR value, although the direction seems to be within ∼2σ of the CMBR dipole. A genuine value of the solar peculiar velocity should be the same irrespective of the data or the technique employed to estimate it. Therefore, such discordant dipole amplitudes, might mean that the explanation for these dipoles, including that of the CMBR, might in fact be something else. But, the observed fact that the direction in all cases, is the same, though obtained from completely independent surveys using different instruments and techniques, by different sets of people employing different computing routines, might nonetheless indicate that these dipoles are not merely due to some systematics, otherwise why would they all be pointing along the same direction. It might instead suggest a preferred direction in the Universe, implying a genuine anisotropy, which would violate the Cosmological Principle, the core of the modern cosmology.

We have defined M cycles as modified form of Gleissberg cycles to study the quasi-periodic secular changes in sunspot activity. Using direct and proxy observations for more than 1200 years we have provided evidence for the influence of the above M cyles on the monsoon rainfall variability and occurrences of major droughts in India. The solar cycle averages of All Indian summer monsoon rainfall (AISMR) and probability of observation of below or above normal AISMR is found to show correlated variations with changes in amplitude of sunspot cycles during the years 1901-2018 AD. Major droughts in India show a preference to occur during minima and declining phases of the M cycles during the years 650-2018 AD . We could generally find low probability of occurrence of droughts in India during the medieval solar maximum epoch ( 1100-1250 AD) and during most of the prolonged sunspot minima periods including the Maunder minima. The evolution of mean Indian summer monsoon rainfall during 650-1900 AD is studied using proxy data from multiple sources with maxima during the 12^th century and minima during 14^th and 19^th centuries. The association of Indian droughts with El-Nino and the possibilities of long term prediction of Indian summer monsoon rainfall variability will be also discussed

A series of D–π–A diketopyrrolopyrrole (DPP)-based small molecules have been designed for organic light-emitting diodes (OLEDs) and organic solar cells (OSCs) applications. Appling the PBE0/6-31G(d,p) method, the ground state geometry and relevant electronic properties were investigated. The first excited singlet state geometry and the absorption and fluorescent spectra were simulated at the TD-PBE0/6-31G(d,p) level. The calculated results reveal that the photophysical properties are affected through the introduction of different end groups. Furthermore, the electronic transitions corresponding to absorption and emission exhibit intramolecular charge transfer feature. It was disclosed that the designed molecules act not only as luminescent for OLEDs, but also donor materials in OSCs. Moreover, they also can be used as potential electron transfer materials using for OLEDs and OSCs.

Despite a global push in the development and implementation of widespread alternative energy use, significant disparities exist across given nation-states. These disparities reflect both technical and economic factors, as well as the social, political, and ecological gaps between how communities see energy development and national/global policy goals. Known as the “local-national gap,” many nations struggle with fostering meaningful conversations about the role of alternative energy technologies within communities. Mitigation of this problem first requires understanding the distribution of existing alternative energy technologies at the local level of policymaking. Using the State of Georgia, U.S.A. as a case study, we present a model for analyzing how existing adoption trends enable/limit conversation at the scale of local governance (i.e., county governments). Leveraging existing work on the Gini Coefficient as a metric for measuring energy inequity, we argue these tools can be applied to analyze where gaps exist in ongoing solar adoption trends. As we demonstrate, communities that adopt solar tend to be concentrated in a few counties, indicating existing conversations are limited to a circumscribed set of social networks. This information and the model we demonstrate can enable focused qualitative analyses of existing solar trends, not only amongst high-adoption areas but within communities where little to no adoption has occurred.

We present observations from evaluation of internal environmental quality of industrial halls with priority on daylighting in combination with the integral lighting. The physical parameters related to indoor lighting in large industrial halls in winter and summer periods were analyzed using in situ measurements and computational methods. These are part of a comprehensive research on indoor environmental quality of industrial halls with the aims of saving energy and providing a comfortable environment for the workers while improving the productivity. The results showed that the procedures used for evaluation of residential or office buildings may not be used for industrial buildings. We also observed that the criteria of occupants’ comforts for indoor industrial buildings may differ from those of other kinds of buildings. Based on these results, an adequate attention is required for designing the industrial buildings. For this reason, appropriate evaluation methods and criteria should be created. We found the measured values of daylight factor very close to the skylight component of the total illumination. The skylight component was observed on average 30% that of the measured daylight factor values. Although the daylight is not emphasized when designing the industrial buildings and its contribution is small, but it is very important for the workers psychology and physiology. The workers must feel a connection with the exterior environment; otherwise, their productivity decreases.

The document sets out three differentiated proposals for the transport of medicines through RPAS with their respective regulations, adapted to different operational categories: open category, special category and military scope. In the open category, an economical and efficient solution is prioritized for urban and rural areas, complying with weight and height regulations, in addition to guaranteeing the stability and quality of medications during transportation. The special category allows more complex operations and in more adverse conditions, such as densely populated areas and long routes, incorporating advanced security measures and training for personnel. In the military field, RPAS are used in conflict zones and hard-to-reach areas, ensuring the safe and rapid delivery of medical supplies under extreme conditions. Success stories in different countries are highlighted, demonstrating significant improvements in delivery times and risk reduction for health personnel.

We delve into the axion-dilaton model within the supergravity framework, with a specific focus on the intricacies of domain wall construction and stability. Employing holographic vitrification, we unravel the dynamics of domain wall formation in gauge theories featuring periodic vacuum structures. Our model, incorporating a QCD-like axion term and a stabilizing dilaton, undergoes scrutiny for conductivity variations under weak disorder. The investigation reveals the model's resilience, manifesting near-perfect conductivity under mild disorder conditions. However, the rigorous mathematical motivation for the holographic setup demands further elucidation. The scattered nature of our results prompts the necessity for a more systematic interpretation of QCD phenomena and conductivity transitions. This study contributes to the mathematical understanding of the axion-dilaton model's behavior, highlighting the imperative for a refined holographic framework and a more coherent interpretation of observed phenomena.

The application of the latest technological innovations has been promoted worldwide to increase farm productivity, including in salt farming. This research aims to determine the determinants of adoption decisions for salt production technology called geomembrane and estimate the adoption impact on technical efficiency. The data in this study is cross-sectional from 215 small-scale salt farmers on Madura Island, East Java, Indonesia. The data was analyzed using logistic regression to identify which factors influenced farmers’ decisions to use geomembrane. The influence of adoption on farmers' technical efficiency was then assessed using propensity score matching (PSM) and data envelopment analysis (DEA). The findings indicate that age and the dummy variables of gender, land ownership, profit-sharing involvement, and membership in the People's Salt Business Group (KUGAR) all had a significant impact on adoption rates. The findings of controlling matched samples using the PSM process reveal that geomembrane application improves and greatly increases farmers' technical efficiency. Those who used geomembranes displayed greater technical efficiency than those who did not. These findings imply that salt production technology should be promoted more to increase productivity, especially geomembrane adoption, through outreach and dissemination of information, including for landowners involved in the profit-sharing system.

Wetlands, which is composed of soil, vegetation and water, has sufficient water supply and is sensitive to climate change. This study analyzed the coupling degree between wetlands and atmosphere, and discussed the influence of environmental factors (solar radiation and water vapor pressure deficit) on latent heat flux by using the experimental data from the Maduo Observatory of Climate and Environment of the Northwest Institute of Eco-Environment and Resource, CAS and WRF model. The results showed, during the vegetation growthing season, the average value of Ω (decoupling factor) is 0.38 in alpine wetlands, indicating the coupling between wetlands and atmosphere is poor; Solar radiation is the main factor influencing the latent heat flux in the results of both observation data analysis and model simulation, and solar radiation and water vapor pressure deficit still have an opposite reaction to latent heat flux; when solar radiation and water vapor pressure deficit increase by 30%, the average daily amount of latent heat flux increases from 5.57 MJ·m-2 to 7.50 MJ·m-2 and decreases to 5.17 MJ·m-2, respectively. This study provides a new research approach for the study of the parameterization of latent heat flux and evapotranspiration under the context of global climate change.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

Downward short-wave (SW) solar radiation is the only essential energy source powering the atmospheric dynamics, ocean dynamics, biochemical processes, etc. on our planet. Clouds are the main factor limiting the SW flux over the land and the Ocean. For the accurate meteorological measurements of the SW flux one needs expensive equipment - pyranometers. For some cases where one does not need golden-standard quality of measurements, we propose estimating incoming SW radiation flux using all-sky optical RGB imagery which is assumed to incapsulate the whole information about the SW flux. We used DASIO all-sky imagery dataset with corresponding SW downward radiation flux measurements registered by an accurate pyranometer. The dataset has been collected in various regions of the World Ocean during several marine campaigns from 2014 to 2022, and it will be updated. We demonstrate the capabilities of several machine learning models in this problem, which are multilinear regression, Random Forests, Gradient Boosting and convolutional neural networks (CNN). We also applied the inverse target frequency (ITF) re-weighting of the training subset and the approach of pre-classification in order to raise the SW flux approximation quality. We found that the CNN is capable of approximating downward SW solar radiation with higher accuracy compared to existing empiric parameterizations. We also found that the ITF reweighting of the training subset increases the approximation quality substantially. The estimates of the SW radiation flux using all-sky imagery may be of particular use in case of the need for the fast radiative budgets assessment of a site.

Free and open source hardware (FOSH) development has been shown to increase innovation and reduce economic costs. This article reviews the opportunity to use FOSH like a sanction to undercut imports and exports from a target criminal country. A formal methodology is presented for selecting strategic national investments in FOSH development to improve both national security and global safety. In this methodology, first the target country that is threatening national security or safety is identified. Next, the top imports from the target country as well as potentially other importing countries (allies) are quantified. Hardware is identified that could undercut imports/exports from the target country. Finally, methods to support the FOSH development are enumerated to support production in a commons-based peer production strategy. To demonstrate how this theoretical method works in practice it is applied as a case study to the current criminal military aggressor nation, who is also a fossil fuel exporter. The results show there are numerous existing FOSH and opportunities to develop new FOSH for energy conservation and renewable energy to reduce fossil fuel energy demand. Widespread deployment would reduce the concomitant pollution, human health impacts, and environmental desecration as well as cut financing of military operations.

We live in the world that is completely entangled on energy and thus, Humankind can no longer do without it, power. With electricity being the main form of energy today, this has increased the complexity of our life today. In Uganda, electricity generation is mainly through hydropower which put the country in the bottleneck of over dependence on one source of energy. Yet, there are many energy systems out there that country can diversify its electricity generation. Therefore, the need to understand, the level of development and utilization of various energy systems has been the underlying question for this present study. Comprehensive literature survey was conducted from the electronic databases including ScienceDirect, Wiley, Sage, Scopus, Taylor & Francis, and Google Scholar. The publications in form of reports, conference papers, working papers, discussion papers, journal articles, book sections and textbooks were considered in this study. In total, 11 energy systems including human and animal energy, solid biomass (firewood), hydropower, wind, geothermal, solar, nuclear, peat, coal, petroleum, and non-solid biomass (methanol, hydrogen, ethanol, biodiesel, and biogas) are described. The current and the future development and utilization of these energy systems has been described. The challenges with their development and utilization were elaborated and the solution the challenges were presented. The hydropower with River Nile being the main river for large hydropower plant construction is the dominance energy system in Uganda. Nuclear energy will be the salvation for the country’s electric energy supply in the near future. Therefore, Uganda needs to bet big on nuclear energy.

In this study, a high energy conversion efficient dye-sensitized solar cells (DSSC) was successfully fabricated by attaching a double anti-reflection (AR) layer which is composed of a subwavelength moth-eye structured polymethyl methacrylate (PMMA) film and a polydimethylsiloxane (PDMS) film. The efficiency is up to 6.79%. The moth-eye structured PMMA film was fabricated by using anodic aluminum oxide (AAO) template which is simple, low-cost and scalable. The nano-pattern of AAO template has been precisely reproduced onto PMMA film. The photoanode is composed of Titanium dioxide (TiO₂) nanoparticles (NPs) with diameter of 25 nm deposited on the fluorine-doped tin oxide (FTO) glass substrate and the sensitizer N3. The double AR layer can effectively improve the short-circuit current density (JSC) and conversion efficiency from 14.77 to 15.79 mA/cm² and from 6.26% to 6.79%, respectively.

As Chronic Non-Communicable Diseases (CNCD) increase, preventive approaches become more crucial. In this review, Calorie Restriction (CR) effects on human beings were evaluated, comparing benefits and risks of different CR diets: classic CR vs ketosis-inducing diets, including Intermittent Fasting (IF), Classic Ketogenic Diet (CKD), Fasting Mimicking Diet (FMD), Very-Low-Calorie Ketogenic Diet (VLCKD) and Spanish Ketogenic Mediterranean Diet (SKMD). Special emphasis on Insulin Resistance (IR) was placed, as it mediates Metabolic Syndrome (MS), a risk factor for CNCD, and predicts MS diagnosis. CR is the most robust intervention known to increase lifespan and health span, with high evidence and known biochemical mechanisms. CR improves cardiometabolic risk parameters, boosts exercise insulin sensitivity response, and there may be benefits of implementing moderate CR on healthy young and middle-aged individuals. However, there is insufficient evidence to support long-term CR. CKD is effective for weight and MS management, and may have additional benefits such as prevention of muscle loss and appetite control. SKMD has extreme significance benefits for all the metabolic parameters studied. Studies show inconsistent benefits of IF compared to classic CR. More studies are required to study biochemical parameters, reinforce evidence, identify risks, and seek effective and safe nutritional CR approaches.

Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

Energy efficiency is, in principle, a simple idea: an output of human value, for example, vehicle-km traveled, divided by the needed input energy. Efficiency improvements are regarded by many as an important means of mitigating not only climate change, but also other environmental problems. Accordingly, many countries have efficiency ratings for appliances and efficiency standards for road vehicles. Despite the vast number of articles published on energy efficiency, few question whether it is a useful or accurate measure in its present form. This review addresses this lack, by a critical review of the literature, not only in energy efficiency, but in other areas of research, such as ‘energy services’, that can help broaden the scope of this idea, both geographically and conceptually. These shortcomings are illustrated in case studies of road passenger transport and buildings. The main findings are that energy efficiency inevitably has an ethical dimension, that feedbacks are more widespread than generally considered, and that conventional efficiency measures omit important energy input items, particularly those concerned with mining of the materials needed for renewable energy plants. Finally, the key results of this review are summarized, and its limitations are discussed, as is the future research needed to overcome these shortcomings.

Based on four major cosmological and astrophysical coincidences, it seems possible to develop a new model of Hubble-Hawking Universe having light speed expansion. Considering the analysis of 740 super novae data, it is possible to consider a constant rate of cosmic expansion. As there is no physical reasoning for the observed speed of light and all the cosmological observations are completely based on speed of light-by considering ‘light speed expansion’ as a characteristic nature of the universe, big bang, inflation, dark energy, quintessence and lambda term like ideal and unidentified concepts can be reviewed and relinquished at fundamental level and a practical model of expanding universe can be developed with ease and clarity. In this context, we would like to emphasize the point that, traditional definition of cosmic red shift is absolutely wrong. In terms of energy of photon, true cosmic red shift must be defined as - ratio of loss of energy in photon to the energy of photon at galaxy. We encourage the reader to see Figure 1 and Table 1 pertaining to light travel distances prepared with $\left(\frac{z}{1+z}\right)\left(\frac{c}{H_0}\right)\cong z_{new}\left(\frac{c}{H_0}\right)$. For data comparison, readers are encouraged to visit https://cosmocalc.icrar.org/ and http://www.atlasoftheuniverse.com/cosmodis.c. It may be noted that, considering 200 million solar masses as a cut off for ordinary gravity, dark matter can be considered as an effect of power law based super gravity of galactic baryonic mass. It is well believed that, Hawking’s findings about black holes are the most important contributions to physics in recent decades. Hence, we appeal the science community to recommend our Hubble-Hawking model for further research and study.

Solar power innately has issues with weather, grid demand and time of day, which for the case of concentrating solar power (CSP) can be mitigated through use of thermal energy storage. Nuclear reactors, including lead-cooled fast reactors (LFRs), can load follow, but have high fixed and low operating costs which can make this economically unattractive. We investigate potential synergies through coupling CSP and LFR together in a single supercritical CO$_2$ Brayton cycle and/or using the same thermal energy storage. Combining these cycles allows for the LFR to thermally charge the salt storage in the CSP cycle during low demand periods to be dispatched when grid demand increases. The LFR/CSP coupling into one cycle is modeled to find the preferred location of the LFR heat exchanger, CSP heat exchanger, sCO$_2$-to-salt heat exchanger (C2S), turbines, and recuperators within the supercritical CO$_2$ Brayton cycle. Three cycle configurations have been studied: two-cycle configuration, which uses CSP and LFR heat for dedicated turbocompressors, has the highest efficiencies but with less component synergies; a combined cycle with CSP and LFR heat sources in parallel is the simplest with the lowest efficiencies; and a combined cycle with separate high temperature recuperators for both the CSP and LFR is a compromise between efficiency and component synergies. Additionally, four thermal energy storage charging techniques are studied: the turbine positioned before C2S, requiring a high LFR outlet temperature for viability; the turbine after the C2S, reducing turbine inlet temperature and therefore power; the turbine parallel to the C2S producing moderate efficiency; and a dedicated circulator loop. While all configurations have pros and cons, use of a single cycle offers component synergies with limited efficiency penalty. Using a turbine in parallel with the C2S heat exchanger is feasible but results in a low charging efficiency, while a dedicated circulator loop offers flexibility and near perfect heat storage efficiency but increasing cost with additional cycle components.

The paper introduces and describes the recent and still ongoing development activities performed in Luxembourg for In-Orbit Attach Mechanisms for (Drag) Sails Modules to be operated from Space Tugs. After some preparatory work aiming at understanding the possible operational aspects, three designs have been completed for their 3D (Metal and Plastic) Printing. The Plastic-printed prototype underwent a series of automated tests where a robotic arm, equipped with an advanced force sensor, replicated four docking scenarii in ideal and degraded modes. The observation of the forces and torques behaviors at and after impact allowed to characterize the typical patterns for the various contacts but also, to identify a type of impact potentially dramatic for the safety of the docking and its equipment: in case of off-axis approach, “point” contacts shall be avoided as they instantaneously transfer the total kinetic energy in a small area that could break.

Due to its spatio-temporal variability, the mismatch between the weather and demand patterns challenges the design of highly renewable energy systems. A principal component analysis is applied to a simplified networked European electricity system with a high share of wind and solar power generation. It reveals a small number of important mismatch patterns, which explain most of the system's required backup and transmission infrastructure. Whereas the first principal component is already able to reproduce most of the temporal mismatch variability for a solar dominated system, a few more principal components are needed for a wind dominated system. Due to its monopole structure the first principal component causes most of the system's backup infrastructure. The next few principal components have a dipole structure and dominate the transmission infrastructure of the renewable electricity network.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.

Effective solar forecasting has become a critical topic in the scholarly literature in recent years due to the rapid growth of photovoltaic energy production worldwide and the inherent variability of this source of energy. Due to the technological and econonomic limitations of energy storage solutions, using other, mosty conventional, sources to cover energy shortfalls and at the same time utilising solar surpluses production becomes necessary. The need to optimize energy systems, ensuring power continuity, and balancing energy supply and demand has led to the development of various forecasting methods and approaches based on meteorological data or photovoltaic plant characteristics. This article presents the results of a meta-review of the solar forecasting literature, including the current state of knowledge and methodological discussion. It presents a comprehensive set of forecasting methods, evaluates current classifications, and proposes a new synthetic typology. The article emphasizes the increasing role of artificial intelligence (AI) and machine learning (ML) techniques in improving forecast accuracy, alongside traditional statistical and physical models. It explores the challenges of hybrid and ensemble models, which combine multiple forecasting approaches to enhance performance. The paper addresses the emerging trends in solar forecasting research, such as the integration of big data and advanced computational tools. Additionally, from a methodological perspective, the article outlines a rigorous approach to the meta-review research procedure, addresses the scientific challenges associated with conducting bibliometric research, and highlights best practices and principles. This includes defining research questions, selecting eligibility criteria, literature search, data extraction, synthesis, and assessing bias and quality. The article contributes to the solar forecasting field by providing up-to-date knowledge, along with insights on the emerging trends, future research directions, and anticipating implications for the theory and practicce.

Buildings’ thermal energy needs are inherently linked to climate conditions. Consequently, it is crucial to evaluate how climate changes affect these energy demands. Despite extensive analysis, a comprehensive assessment involving a diverse range of building types has not been consistently conducted. The primary objective of this research is to perform a coherent evaluation of the influence of climate changes, construction element properties, and the Heating, Ventilation, and Air Conditioning (HVAC) system type of control on the energy requirements of six buildings (residential, services, and commercial). The buildings are considered located in a temperate Mediterranean climate. Our focus is on the year 2070, considering three distinct climatic scenarios: (i) maintaining the current climate without further changes, (ii) moderate climate changes, and (iii) extreme climate changes. The buildings are distributed across three different locations, each characterized by unique climatic conditions. Buildings’ envelope features a traditional External Thermal Insulation Composite System (ETICS) and expanded polystyrene (EPS) serves as thermal insulation material. Two critical design factors are explored: EPS thickness ranging from 0 (no insulation) to 12 cm; and horizontal external fixed shading elements varying lengths from 0 (absence) to 150 cm. Six alternative setpoint ranges are assessed for the HVAC system control: three based on the Predicted Mean Vote (PMV) and three based on indoor air temperature (Tair). Results were obtained with a validated in-home software tool. They show that, even under extreme climate conditions, the application of thermal insulation remains energetically favorable, however its relative importance diminishes as climate severity increases. Then, proper insulation design remains important for energy efficiency. The use of external shading elements for glazing (e.g., overhangs, louvers) proves beneficial in specific cases. As climate changes intensify, the significance of shading elements grows. Thus, strategic placement and design are necessary for good results. The HVAC system’s energy consumption depends on the level of thermal comfort requirements, on the climate characteristics and on the building’s type of use. As climate change severity intensifies, energy demands for cooling increase, while energy needs for heating decrease. However, it’s essential to recognize that the impact of climate changes on HVAC system energy consumption significantly depends on the type of building.

Accurate short-term solar irradiance forecasting is crucial for the efficient operation of solar energy driven photovoltaic (PV) power plants. In this research, we introduce a novel hybrid ensemble forecasting model that amalgamates the strengths of machine learning tree-based models and deep learning neuron-based models. The hybrid ensemble model integrates the interpretability of tree-based models with the capacity of neuron-based models to capture complex temporal dependencies within solar irradiance data. Furthermore, stacking and voting ensemble strategies are employed to harness the collective strengths of these models, significantly enhancing prediction accuracy. This integrated methodology is enhanced by incorporating pixels from satellite images provided by the European Organization for the Exploitation of Meteorological Satellites (EUMETSAT). These pixels are converted into structured data arrays and employed as exogenous inputs in the algorithm. The primary objective of this study is to improve the accuracy of short-term solar irradiance predictions, spanning a forecast horizon up to 6 hours ahead. The incorporation of EUMETSAT satellite image pixels data enables the model to extract valuable spatial and temporal information, thus enhancing the overall forecasting precision. This research also includes detailed analysis of the derivation of GHI using satellite images. The study was carried out and the models tested across three distinct locations in Austria. A detailed comparative analysis was carried out for traditional Satellite (SAT) and Numerical Weather Prediction (NWP) models with hybrid models. Our findings demonstrate a higher skill score for all of the approaches compared to smart persistent model and consistently highlight the superiority of the hybrid ensemble model for short-term prediction window of 1 to 6 hours. This research underscores the potential for enhanced accuracy of the hybrid approach to advance short-term solar irradiance forecasting, emphasizing its effectiveness at understanding the intricate interplay of the meteorological variables affecting solar energy generation worldwide. The results of this investigation carry noteworthy implications for advancing solar energy systems, thereby supporting the sustainable integration of renewable energy sources into the electrical grid.

This research introduces Genus-Physiognomy-Ecosystem (GPE) mapping at a prefecture level through machine learning of multi-spectral and multi-temporal satellite images at 10m spatial resolution, and later integration of prefecture wise maps into country scale for dealing with 88 GPE types to be classified from a large size of training data involved in the research effectively. This research was made possible by harnessing entire archives of Level-2A product, Bottom of Atmosphere reflectance images collected by MultiSpectral Instruments onboard a constellation of two polar-orbiting Sentinel-2 mission satellites. The satellite images were pre-processed for cloud masking and monthly median composite images consisting of 10 multi-spectral bands and 7 spectral indexes were generated. The ground truth labels were extracted from extant vegetation survey maps by implementing systematic stratified sampling approach and noisy labels were dropped out for preparing a reliable ground truth database. Graphics Processing Unit (GPU) implementation of Gradient Boosting Decision Trees (GBDT) classifier was employed for classification of 88 GPE types from 204 satellite features. The classification accuracy computed with 25% test data varied from 65-81% in terms of F1-score across 48 prefectural regions. This research produced seamless maps of 88 GPE types first time at a country scale with an average 72% F1-score. In addition, mapping of solar panels and vegetation disturbance are added.

Based on measured astronomical position data of heavenly objects in the Solar System and other planetary systems, all bodies in space seem to move in some kind of elliptical motion with respect to each other, whereas objects follow parabolic escape orbits while moving away from Earth and bodies asserting a gravitational pull, and some comets move in near-hyperbolic orbits when they approach the Sun. In this article, it is first mathematically proven that the “distance between points on any two different circles in three-dimensional space” is equivalent to the “distance of points on a vector ellipse from another fixed or moving point, as in two-dimensional space.” Then, it is further mathematically demonstrated that “distance between points on any two different circles in any number of multiple dimensions” is equivalent to “distance of points on a vector ellipse from another fixed or moving point”. Finally, two special cases when the “distance between points on two different circles in multi-dimensional space” become mathematically equivalent to distances in “parabolic” or “near-hyperbolic” trajectories are investigated. Concepts of “vector ellipse”, “vector hyperbola”, and “vector parabola” are also mathematically defined. The mathematical basis derived in this Article is utilized in the book “Everyhing Is A Circle: A New Model For Orbits Of Bodies In The Universe” in asserting a new Circular Orbital Model for moving bodies in the Universe, leading to further insights in Astrophysics.

Many Caribbean island nations have historically been heavily dependent on imported fossil fuels for both power and transportation, while at the same time being at an enhanced risk from the impacts of climate change, although their emissions represent a very tiny fraction of the global total responsible for climate change. Small island developing states (SIDS) are among the leaders in advocating for the ambitious 1.5°C Paris Agreement target and the transition to 100% sustainable, renewable energy systems. In this work we present three central results. First, we show through GIS mapping of all Caribbean islands the potential for near-coastal deep-water as a resource for Ocean Thermal Energy Conversion (OTEC) and couple these results with an estimate of the countries for which OTEC would be most advantageous due to a lack of other dispatchable renewable power options. Second, hourly data have been utilized to explicitly show the trade-offs between battery storage needs and dispatchable renewable sources such as OTEC in 100% renewable electricity systems, both in technological and economic terms. Finally, the utility of near-shore, open-cycle OTEC with accompanying desalination is shown to enable a higher penetration of renewable energy and lead to lower system levelized costs than those of a conventional fossil fuel system.

As renewable energy generation prediction systems have been introduced into the energy trading market, accurate prediction of solar photovoltaic (PV) energy generation has become a crucial challenge for ensuring stable trade of variable energy. Therefore, it is essential to quantitatively investigate and analyze current prediction technology and develop more advanced prediction systems. In this study, three models for predicting PV energy generation were investigated. Multiple regression, random forest, and gradient boosting machine (GBM) models were con-structed for 15 utility-scale power plants throughout South Korea. Model performance was evaluated in terms of root mean square error (RMSE) and mean absolute error (MAE). The multiple regression-based model had an RMSE of 12.00% and MAE of 9.06%. The random forest model had an RMSE of 11.69% and MAE of 8.61%. The GBM model had an RMSE of 11.34% and MAE of 8.18%, indicating its superior accuracy among the three models in predicting PV energy generation. These findings provide valuable insights that may contribute to the development of advanced PV energy generation models and their application in grid operations.

Perovskite solar cells have shown significant progress, but their commercialization remains hindered by lead-based toxicity. Many nontoxic perovskite-based solar cells have demonstrated potential such as Cs2AgBi0.75Sb0.25Br6, but their power-conversion efficiency is inadequate. To address this issue, some researchers are focusing on emerging acceptor-donor-acceptor'-donor-acceptor (A-DA'D-A) type non-fullerene acceptors (NFAs) for Cs2AgBi0.75Sb0.25Br6 to find effective electron transport layers for high-performance photovoltaic responses with low voltage drops. In this comparative study, four novel A-DA'D-A types NFAs such as BT-LIC, BT-BIC, BT-L4F, and were used as an electron transport layer (ETL) for the proposed devices, FTO/PEDOT: PSS/ Cs2AgBi0.75Sb0.25Br6/ETL/Au. Comprehensive simulations were conducted to optimize the devices. The simulations showed that all optimized devices exhibit photovoltaic responses, with the BT-BIC device having the highest power conversion efficiency (13.2%) and the BT-LIC device having the lowest (6.8%). The BT-BIC as ETL provides fewer interfacial traps and better band alignment, enabling greater open-circuit voltage for efficient photovoltaic responses.

In this paper, the performance of Cu-(In,Ga)-S2 (CIGS2) solar cells with adjusting composite CGI-ratio absorber is explored and compared through an improved three-stage co-evaporation technique. For co-evaporating CIGS2 absorber as a less toxic alternative to Cd-containing film, we analyse the effect of the CGI-ratio stoichiometry and crystallinity, and explore its opto-electric sensing characteristic of individual solar cell. The results of this research signify the potential of high-performance CIGS2-absorption solar cells for photovoltaic (PV)-module industrial applications. For the optimal CIGS2-absorption film (CGI=0.95), the Raman main-phase signal (A1) falls at 291 cm-1, which is excited by the 532-nm line of Ar+-laser. Using photo-luminescence (PL) spectroscopy, the corresponding main-peak bandgaps measured is 1.59 eV at the same CGI-ratio film. Meanwhile, the best conversion efficiency (=3.212%) and the average external quantum efficiency (EQE=51.1% in the visible-wavelength region) of photo-electric properties were achieved for the developed CIGS2-solar cells (CGI=0.95). The discoveries of this CIGS2-absorption PV research provide a new scientific understanding of solar cells. Moreover, this research undeniably contributes to a major advancement towards practical PV-module applications and can help more to build an eco-friendly community.

Fluorinated compounds and co-enzymes are being widely researched and employed throughout research community because of their versatile physical, chemical and biological properties. In this work, we synthesized NiS-NiO/S-g-C3N4, a highly effective photocatalyst for C(sp3)-F bond activation and the regeneration of coenzyme (1,4-NADH) employing a new and ecologically acceptable route. The obtained photocatalyst exhibited important photocatalytic properties, such as good solar light harvesting ability, suitability of the optical band-gap, and facilitating efficient charge migrations. As a result, the newly designed NiS-NiO/S-g-C3N4 photocatalyst shows the excellent yield for regenerations of 1,4-NADH (51%). Further, a method of combining C(sp3)-F bond activation with photocatalysis has been demonstrated that represents a very powerful and sustainable approach, that can be a major breakthrough for the field of pharmaceutical.

The recent provision of energy-harvesting capabilities to wireless sensor networks has entailed the redefinition of design objectives. Specifically, the traditional goal of maximizing network lifetime has been replaced by optimizing network performance, namely delay and throughput. The present paper contributes to this reformulation by considering the routing problem for the class of time-driven energy-harvesting WSN (EH-WSN) under regular or quasi-periodic energy sources. In particular, this paper shows that the minimum hop count (MHC) criterion maximizes the average duty cycle that can be sustained by nodes in this type of scenarios. This is a primary objective in EH-WSN, since large duty cycles lead to enhanced performance. Based on a previous result, a general expression is first obtained which gives mathematical form to the relationship between duty cycle and traffic load for any node in a time-driven EH-WSN fed by a regular energy source. This expression reveals that the duty cycle achievable by a node decreases as its traffic load increases. Then, it is shown that MHC minimizes the average traffic load over the network, and thus it maximizes the average duty cycle of nodes. This result is numerically validated via simulation by comparison with other well-known routing strategies. Accordingly, this paper suggests assigning top priority to the MHC criterion in the development of routing protocols for time-driven EH-WSN under regular energy sources.

Long-span steel structure trusses are widely used in factory buildings, but with the growth of service time and the increase of dynamic load fatigue, a considerable part of the long-span truss with dynamic load appears serious transverse cracks at the bottom of the middle span and oblique deformation of the abdomen in the operation process. The U-shaped cracks at the bottom and belly, as well as the mid-span down deflection of the main truss, reduced the functional function of the factory building truss structure, and had to limit the original crane load, which affected the normal safety and durability of the structure. Therefore, the application principle of the variable axial force cable system in the long-span factory building truss structure and 3D3S software modeling [1] were used. Analyzing and studying the reinforcement method of large-span powerhouse truss can provide practical experience for subsequent similar projects. In view of the above phenomenon, the large-span powerhouse trusses of Hongcheng Powerhouse 1 and No.2 located in Tonglu, Zhejiang Province are used as the research object, and the variable axial force cable method is proposed to strengthen and lift the load. Considering the span of large-span powerhouse truss, the cable system with 22m controlling force of 400kN is proposed to be selected for powerhouse 1, and the cable system with variable axial force of 24m is proposed to be selected for Powerhouse 2. The force model of large-span truss is established by using the finite element method commonly used to analyze the force of truss. Under two working conditions, The influence of reinforcement effect is analyzed and compared from three aspects: stiffness, bearing capacity and stability. And the phenomenon of uneven stress distribution is analyzed. The stress distribution characteristics of each node are understood by simulating the most disadvantageous node plates with the greatest internal force before and after reinforcement.

This study delves into the intricate interplay between cosmology and gravity in dilaton-based models, enhancing our understanding. Exploring boundary theories coupled to gravity, we derive a four-dimensional effective theory from the cosmological constant. Dilaton gravity is then scrutinized, revealing elegant solutions and insights into brane embedding. The analysis extends to probe scalar fields, employing the WKB approximation in both conformal and non-conformal cases. In summary, this work contributes to a nuanced understanding of the complex relationship between cosmology and gravity in dilaton-based frameworks.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

Of all the renewable energy sources, solar photovoltaic (PV) power is estimated to be a popular source due to several advantages such as its free availability, absence of rotating parts, integration to building such as rooftops, and less maintenance cost. The nonlinear current-voltage (I–V) characteristics and power generated from a PV array primarily depend on solar insolation/irradiation and panel temperature. The extracted PV output power is influenced by the accuracy with which the nonlinear power–voltage (P–V) characteristic curve is traced by the maximum power point tracking (MPPT) controller. In this paper, a bio-inspired roach infestation optimization (RIO) algorithm is proposed to extract the maximum power from the PV system (PVS). To validate the usefulness of the RIO MPPT algorithm, MATLAB/Simulink simulations are performed under varying environmental conditions, for example, step changes in solar irradiance, and partial shading of the PV array. Furthermore, the search performance of the RIO algorithm is examined on different unconstrained benchmark functions, and it is that realized that the RIO algorithm has improved convergence characteristics in terms of finding the optimal solution than Particle swarm optimization (PSO). The results demonstrated that the RIO-based MPPT performs remarkably in tracking with high accuracy as the PSO-based MPPT.

This paper presents a microgrid distributed energy resources (DERs) for a rural standalone system. It is made up of solar photovoltaic (solar PV) system, battery energy storage system (BESS), and wind turbine coupled to permanent magnet synchronous generator (WT-PMSG). The DERs are controlled by maximum power point tracking (MPPT) based proportional intergral (PI) controllers for both maximum power tracking and error feedback compensation. The MPPT uses the perturb and observe (P&O) algorithm for tracking the maximum power point of the DERs. The PI gains are tuned using the Ziegler-Nichol’s method. The developed system was built and simulated in MATLAB/Simulink under two conditions - constant load, and step load changes. The controllers enabled the BESS to charge even during conditions of varying load and other environmental factors such as change of irradiance and wind speed. The reference was tracked very well by the output voltage of the DC grid. This is a useful research for electrifying the rural islanded areas, too far from the grid.

The world is in the grips of the COVID-19 pandemic. Public health measures that can reduce the risk of infection and death in addition to quarantines are desperately needed. This article reviews the roles of vitamin D in reducing risk of respiratory tract infections, knowledge about the epidemiology of influenza and COVID-19, and how vitamin D supplementation might be a useful measure to reduce risk. Through several mechanisms, vitamin D can reduce risk of infections. Those mechanisms include inducing cathelicidins and defensins that can lower viral replication rates and reducing concentrations of pro-inflammatory cytokines that produce the inflammation that injures the lining of the lungs, leading to pneumonia, as well as increase concentrations of anti-inflammatory cytokines. Several observational studies and clinical trials reported that vitamin D supplementation reduced risk of influenza, whereas others did not. Evidence supporting the role of vitamin D in reducing risk of COVID-19 includes that the outbreak occurred in winter, a time when 25-hydroxyvitamin D [25(OH)D] concentrations are lowest; that the number of cases in the Southern Hemisphere near the end of summer are low; that vitamin D deficiency has been found to contribute to acute respiratory distress syndrome, and that case-fatality rates increase with age and with chronic disease comorbidity, both of which are associated with lower 25(OH)D concentration. To reduce risk of infection, it is recommended that people at risk of influenza and/or COVID-19 consider taking 10,000 IU/d of vitamin D₃ for a few weeks to rapidly raise 25(OH)D concentrations, followed by 5000 IU/d. The goal should be to raise 25(OH)D concentrations above 40–60 ng/ml (100–150 nmol/l). For treatment of people who become infected with COVID-19, higher vitamin D₃ doses might be useful. Randomized controlled trials and large population studies should be conducted to evaluate these recommendations.

We introduce the linear subgroup of volume-preserving diffeomorphism as the underlying symmetry to construct an action within the effective field theory framework and the Schwinger-Keldish formalism. The formulated action is posited to effectively incorporate dissipative effects into the Navier-Stokes equations.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

Supermarkets in Port Harcourt (PH) city, Nigeria, predominantly rely on diesel electricity generation due to grid instability, leading to high cost of electricity prices. Although solar photovoltaic (PV) systems have been proposed as an alternative, these supermarkets have yet to adopt them, mainly due to high investment costs and a lack of awareness of the long-term financial and environmental benefits. This paper examines the technical and economic practicality of a PV system for these supermarkets using the PVsyst software and a spreadsheet model. Solar resources showed that PH has a daily average solar radiation and temperature of 4.21 kWh/m2/day and 25.73℃, respectively. Market Square, the supermarket with the highest peak power demand of 59.8 kW, and a 561 kWh/day load profile, was chosen as a case study. A proposed PV system with a power capacity of 232 kW, battery storage capacity of 34,021 Ah, a charge controller size of 100 A/560V, and an inverter with a power rating of 60V/75 kW has been designed to meet the load demand. The economic analysis showed a $266,936 life cycle cost, $0.12 per kWh levelized cost of electricity (LCOE), 4-year simple payback time, and a 20.5% internal rate of return (IRR). The PV system is feasible due to its positive net present value (NPV) of $165,322 and carbon savings of 582 tCO2/year.

The need to address climate change and establish sustainable urban environments has driven increased efforts in Europe to develop climate-neutral cities. This study highlights the importance of integrating solar energy technologies and nature-based solutions as key strategies to achieve climate neutrality. By examining current practices, emerging trends, and case examples, it explores the benefits, challenges, and prospects associated with the integration of solar energy and nature-based solutions in urban contexts. The study presents a pioneering approach to assess the urban heat and climate change mitigation benefits of combining building-integrated photovoltaics and nature-based solutions specifically within the European context. The results emphasize the synergistic relationship between nature-based components and solar conversion technology, identifying effective combinations for different climatic zones. In warmer regions of Southern Europe, strategies like rooftop photovoltaics on cool roofs, photovoltaics shadings, green walls, and urban trees have demonstrated effectiveness. Conversely, mid- and high-latitude European cities have seen positive impacts through the integration of rooftop photovoltaics and photovoltaics facades with green roofs and green spaces. As solar cell conversion efficiency improves, the environmental impact of photovoltaics is expected to decrease, facilitating their integration into urban environments. The study emphasizes the importance of incorporating water bodies, cool pavements, spaces with high sky-view factors, and effective planning in urban design to maximize resilience benefits. It also highlights the significance of prioritizing mitigation actions in low-income regions and engaging citizens in the development of social photovoltaics positive energy houses, resilient neighbourhoods, and green spaces. By adopting these recommendations, European cities can lead the way in creating climate-neutral urban environments that prioritize clean energy, nature-based solutions, and the overall well-being of residents. The findings underscore the need for a multidisciplinary approach that combines technological innovation, urban planning strategies, and policy frameworks to effectively achieve climate neutrality in European cities.

The diverse socio-economic and environmental impacts that the set-up of a new photovoltaic installation has must be weighed carefully in order to reach the best possible solution. Among the different photovoltaic systems there are several classification criteria, depending on the technology, application and the size of the modules that define them. The size (installed nominal capacity) stands out as an impartial and critical measure in the decision making process. In this article we use a multi-criteria decision making method to analyse the responses of five experts to a detailed questionnaire in which several different criteria are correlated with various photovoltaic installation sizes. The limitation associated to the low number of experts is addressed with a robustness and sensitivity analysis. With this study we seek first, to apply and demonstrate the feasibility of a methodology which combines technical information with multi-criteria decision making methods, and second, to obtain a clear result oriented that increases the benefits of a forthcoming photovoltaic installation of modules in distributed generation adding up to 1GW total peak power in standard conditions. We observe a consistent result in which smaller photovoltaic modules are the ideal solution that maximises the socio-economic benefits of any installation. If a decision has to be taken about the type of photovoltaic plant to be installed, the conclusion is clear: given a certain size, small, easily scalable installations are the best solution for stake-holders, for the inhabitants, and for the environment.

In this paper, the overall performance of Cu-(In,Ga)-Se₂ (CIGSe) solar cells was improved in the ultraviolet (UV)–visible wavelength region by two-segment process. In which, adjusting DC sputtering powers (20–40 W) for absorbers (segment I), and metal-alloy compositions (CdS, ZnO/CdS, ZnMgO/CdS and ZnMgO) for buffers (segment II) were explored and characterized. Upon choosing the optimal-30-W CIGSe-absorber (with 0.95-CGI ratio) sputtered by the segment-I process, the Cu-rich film can distinctly boost grain growth, thus reducing the trap state density. After segment-II process as the toxic-CdS alternative, the optimal Zn_0.9Mg_0.1O-alloy buffer can reach the best conversion efficiency (η = 8.70%) was attained for the environmental protection. Meanwhile, and the overall internal/external quantum efficiencies (IQE/EQE) were improved by 13.15%, respectively for the 2.48–3.62-eV bandgap (short wavelength) range. The developed photovoltaic (PV) module (with 9 optimum-CIGSe cells) exhibits acceptable stability with a variance within ±5% over the 60-day experiment. This discovery in PV-device research contributes to a new scientific understanding of renewable energy. Furthermore, this study undeniably enhances the progress of practical applications for PV-modules in alignment with sustainable development goals. It also actively supports the development of eco-friendly communities.

Addressing global environmental problem, water splitting to produce hydrogen fuel by solar energy is getting so much attention. In the water splitting, the essential problem to solve is the development of efficient　catalysts for oxygen production. In this paper, having the prospect for a practical application of photocatalysts to artificial photosynthesis, molecular mechanisms in the current literature are briefly reviewed. At first, recent progress in the function of Mn cluster at the natural photosystem II is briefly described. The kinds of devices in which oxygen evolution reaction (OER) catalysts are used were designated; water electrolyzers, photoelectrodes, and photocatalysts. Some methods for analyzing molecular mechanism in OER catalysis, emphasized by FTIR method, are shown briefly. After describing common OER mechanisms, the molecular mechanisms are discussed for TiO2 and BiVO4 photoelectrodes with our novel data, followed by presenting of co-catalysts IrO2, RuO2, NiO2, and other metal oxides for OER catalysts. Recent reports describing OER catalysts of perovskites, layered double hydroxides (LDH), metal-organic frameworks (MOF), single atom catalysts, as well as metal complexes are reviewed. Finally, by comparing with natural photosystem, the requiring factors to improve the activity of the catalysts for artificial photosynthesis will be discussed.

As renewable energy generation prediction system has been introduced into the energy trading market, making a model to accurately predict the quantity of solar photovoltaic (PV) energy generation has become a significant problem. Moreover, to encourage an accurate prediction of the quantity of energy generation, an incentive system has been implemented for those who predict the quantity of solar PV energy under the error rate of 8%. Therefore, it has become more important to investigate and analyze current prediction technology numerically and develop more advanced prediction system. In this study, we tried to develop a better model to improve the accuracy of solar PV energy generation quantity by comparing three models made with gradient boosting machine (GBM), Model 1, Model 2, Model 3 respectively. Model 1 was built with the whole training data set without any additional preprocessing. After conducting some additional preprocessing procedure to predict solar energy generation more accurately, we made Model 2 with the whole training data set and Model 3 with only upper 10% of energy generation capacity. To compare the accuracy of three models, normalized mean absolute error (nMAE) was used as an evaluation index. The nMAE of Model 1 was 9.64% while the Model 2 showed 8.41%. Also, Model 3, which was constructed with the training set of upper 10% energy generation capacity, outperformed with the nMAE of 8.08%. For further study, to check the effectiveness of models constructed with GBM, a time series model, autoregressive integrated moving average (ARIMA), was also built and the nMAE was compared.

This research aimed to determine the most viable locations for establishing solar energy facilities in Yemen through the utilization of the Analytical Hierarchy Process (AHP), Best-Worst Method (BWM), and Geographic Information System (GIS). A total of twelve key criteria were meticulously selected and evaluated based on their impact on the appropriateness of sites for solar power plants. These criteria were amalgamated using a weighted overlay tool, resulting in a map that classified regions as either optimal, highly suitable, or suitable. The findings of the study indicated that the eastern, southern, and northern parts of Yemen are prime candidates for solar energy installations due to their moderate climate and flat topography. On the other hand, the western regions were deemed less favorable. The breakdown of site classifications revealed that 38% of areas were optimal, 61% were highly suitable, and only 1% were considered suitable, based on the assigned weights from the AHP and BWM methodologies. Moreover, a sensitivity analysis was carried out to evaluate the impact of adjusting the weights of Global Horizontal Irradiance (GHI) and slope on site classifications. A minor increase in the weights of GHI (from 30% to 31%) and slope (from 10% to 11%) resulted in a significant alteration in the suitability categories, highlighting the importance of weight adjustments in multi-criteria decision-making processes. In conclusion, the study emphasizes the effectiveness of AHP, BWM, and GIS in assessing site suitability for solar energy facilities, as well as the significance of sensitivity analyses. These approaches provide valuable insights for decision-makers, aiding in strategic planning and fostering sustainable energy development in Yemen.

The hybridization of conventional thermal power plants by incorporation of renewable energy systems has witnessed widespread adoption in recent years. This trend aims not only to mitigate carbon emissions but also to enhance the overall efficiency and performance of these power generation facilities. However, calculating the performance of such intricate systems using fundamental thermodynamic equations proves to be both laborious and time-intensive. Nevertheless, possessing accurate and real-time insights into their performance is of utmost significance to ensure optimal plant operation, facilitate decision-making, and streamline power production planning. In this paper, we delve into the application of machine learning techniques, particularly hybrid methodologies, to predict the performance of power plants. Specifically, we employ three approaches: the Adaptive Neuro-Fuzzy Inference System (ANFIS), the ANFIS optimized via Particle Swarm Optimization (ANFIS-PSO), and the ANFIS optimized through Genetic Algorithm (ANFIS-GA). These techniques are alternatively applied to a complex hybrid thermal power plant, namely an Integrated Solar Combined Cycle Power Plant (ISCCPP). This ISCCPP comprises a steam turbine section, a gas turbine section, and a concentrated solar power system utilizing troughs as collectors. The energy transfer fluid, in conjunction with exhaust from the gas turbine section, heats water within a vessel or steam generator, producing steam to propel the steam turbine's rotor. Electricity generation is facilitated by both gas and steam turbines, which are coupled to a generator. The findings of this study underscore the accuracy and appropriateness of ANFIS-based models in evaluating and predicting the performance of intricate hybrid power plants. The ANFIS model exhibited an impressive overall coefficient of correlation of 0.9991. Notably, the integration of evolutionary algorithms (PSO and GA) into the ANFIS framework elevated model performance, yielding correlation coefficients of 0.9994 for ANFIS-PSO and 0.9997 for ANFIS-GA. It is noteworthy that ANFIS-GA demonstrated superior predictive capability. The modeling framework developed in this research offers valuable support to designers, energy managers, and decision-makers. It provides a robust and dependable tool to assess the performance of hybrid thermal power plants, which are poised for a global surge in numbers amid the ongoing energy transition.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .