This work aims to investigate systematically the influence of process temperature and biomass-to-water ration on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas analyzer. For constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases a smooth growth. By variation of biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total carboxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentrations of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio.

In this paper an overview of waste materials in underground coal mines is presented, whereas waste materials can be of anthropogenic or geogenic origin. Complex interactions with mine water and waste materials take place, especially during mine water level rebound. Bearing in mind that under the increasing societal pressure most, if not all underground coal mines are going to be closed rather sooner than later, it is important to understand these interactions and to predict the composition and dynamics of mine water lever rebound in underground coal mines to prevent adverse effects to the environment, especially receiving waters and drinking water resources. The second part of this article focusses on the experiences gained in the Ruhr area, a closed underground coal mining region in Western Germany, where mine water rebound has been ongoing for decades. In this regard, the modelling program DMT-Boxmodel has been developed and applied to predict the hydrodynamics and hydrogeochemical development of the water rebound. As an example, simulation results of water rebound as well as solute and PCB transport in central province of Ruhr mining area are compared to the monitoring data, and predictions over 3 decades are given. The experiences gained in the mine water management in Ruhr area can be applied in mining areas worldwide.

Molecular hydrogen (H2) has been shown to have antioxidant and anti-inflammatory activities that may reduce the development and progression of many diseases. In this study, Hydrogen-rich water (HRW) was obtained by reacting hybrid magnesium-carbon hydrogen storage materials with water. Then the effects of intake of HRW on the activities of xenobiotic-metabolizing enzymes, membrane transporters, and oxidative stress in rats were investigated. Rats were given HRW ad libitum for 4 weeks. Results showed that intake of HRW had no significant effect on the activities of various cytochrome P450 (CYP) enzymes (CYP1A1, 1A2, 2B, 2C, 2D, 2E1, 3A, 4A), glutathione-S-transferase and UDP-glucuronosyltransferase. Except for a slight lower plasma glucose concentration, intake of HRW had no effect on other plasma biochemical parameters in rats. P-Glycoprotein and multidrug resistance-associated protein (Mrp)2 protein expressions in liver were elevated after intake of HRW. However, HRW had no significant effects on glutathione, glutathione peroxidase, or lipid peroxidation in liver. Results from this study suggest that consumption of HRW may not affect xenobiotic metabolism or oxidative stress in liver. However, intake of HRW may increase the efflux of xenobiotics or toxic substances from the liver into bile by enhancing the expression of p-glycoprotein and Mrp2 protein.

The state of Veracruz has ample water resources. However, due to population and industrial growth, there has been an increase in the discharge of wastewater into surface water bodies. To analyze the water quality in the Bobos River, Veracruz, and its sustainability, researchers collected nine samples from nine different points in the reservoir. They measured various parameters such as temperature, pH, dissolved oxygen, conductivity, total nitrogen, nitrate, chemical oxygen demand, total phosphorus, phosphate, dissolved solids, and fecal coliforms. The results showed that the river's water quality is at risk. The concentration of pollutants such as chemical oxygen demand and fecal coliforms is high. Conductivity values ranged from 0.26 to 3.81 mS. If preventive and corrective measures are not taken, the river's ability to purify pollutants will be severely compromised. This study evaluates the physical, chemical, and microbiological characteristics of the water in Bobos River. It specifically investigates the influence of the nearby citrus industry on the river's water quality. The study also aims to promote environmental sustainability.

The future of the Colorado River water supply (WS) affects millions of people and the U.S. economy. A recent study suggested a cross-basin correlation between the Colorado River and its neighboring Great Salt Lake (GSL). Following that study, the feasibility of using the previously developed multi-year prediction of the GSL water level to forecast the Colorado River WS was tested. Time-series models were developed to predict the changes in WS out to 10 years. Regressive methods and the GSL water level data were used for the depiction of decadal variability of the Colorado River WS. Various time-series models suggest a decline in the 10-year-averaged WS since 2013 before starting to increase around 2020. Comparison between this WS prediction and the WS projection published in a 2012 government report (derived from climate models) reveals a widened imbalance between supply and demand by 2020. Further research to update similar multi-year prediction of the Colorado River WS is needed. Such information could aid in management decision making in the face of future water shortages.

The surface planarity and asperity removal behaviors of atomic scale under the ultrathin water environment was studied for the nanoscale process by molecular dynamics simulation. The monolayer atomic removal was achieved under the noncontact and monoatomic layer contact conditions with different water film thickness, and the newly formed surface is relatively smooth and no deformed layer and plastic defects exist. The nanoscale processing is governed by the interatomic adhering action during which the water film transmits the loading forces to Cu surface and thereby result in the migration and removal of surface atoms. With scratching depth ≥ 0.5 nm, the abrasive particle squeezed out the water film from scratching region and scratched Cu surface directly, leading to the surface quality deterioration mainly governed by the plowing action. This study brings the goals of “0 nm planarity, 0 residual defects and 0 polishing pressure” closer to us in the nanoscale process for the development of ultra-precision manufacture technology.

There are numerous approaches to model an influence of manufacturing parameters on the dissolution and disintegration of solid dosage forms. A modern approach for modelling and simulating complex and heterogeneous systems such as pharmaceutical tablets focuses on computationally-intensive finite-element or discreet element methods. Industrial challenges such as Process Analytical Technology (PAT) and Quality by Design are stimulating computer-based technologies to design, control and improve the quality of pharmaceutical compacts and their performance. In this study the disintegration and dissolution model based on the numerical solutions of the Noyes-Whitney equation and cellular automata supported disintegration model are proposed and evaluated. The results from in vitro release studies of the mefenamic acid formulations were compared to the calculated release patterns from the tablet structures obtained from microtomography experiments and the purely algorithmically created virtual tablets.

A complete halt on all anthropogenic activities and human movement due to COVID-19 lockdown has provided a great opportunity to assess the impact of human activities on coastal marine ecosystems. The current study assessed the concentration of the metals in water samples of the largest brackish water lagoon of Asia; the Chilika lagoon in the state of Odisha, India between pre-COVID-19 and post-COVID-19 lockdown scenarios. Monthly water samples (n=30 stations) from 0.3 m depth were collected from three sectors of the lagoon seasonally; pre-monsoon, monsoon, and post-monsoon. In addition to various physical parameters [pH, salinity, alkalinity, (DO) dissolved oxygen, (TDS) total dissolved solids, and (EC) electrical conductivity] the collected water samples were analysed for 18 trace metals (Al, As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sr, Th, Tl, U, V). Most of the physical parameters showed a significant variation between pre-and post-COVID-19 scenarios, except for pH and DO. The concentration of five metals (Be, Cd, Co, Ni, and Pb) remained below detection limits in all water samples. The impact of COVID-19 lockdown on the concentration of the metal in the water samples was noticed along with the three sectors of the lagoon. However, eight metals (Al, As, Cr, Fe, Mn, Th, U, and V) were significantly different between the COVID-19 scenarios and the remaining five metals were not statistically significant. The mean concentration of Al, As, Fe, Th, and V were higher in the pre-COVID-19 scenarios, whereas only Cr and Mn were higher in the post-COVID-19 scenarios. The mean concentration of U was similar among both COVID-19 scenarios, even though there were seasonal and sectoral differences. The seasonal influence of riverine influx was more evident on metal concentration during the monsoon season, whereas the difference between sectors was more prominent during the post-monsoon season. An increased number of correlations between physical parameters and metal concentration were observed in the post-monsoon season and post-COVID-19 scenario. This study provides evidence that the imposition of COVID-19 lockdown reduced metal influx in the water column and improved the water quality of the Chilika lagoon. Our results can be used as baseline for metal concentration in surface waters of the lagoon.

Mediterranean coastal lagoons and their peripheral areas often provide a collection of habitats for many species, and they often face significant threats from anthropogenic activities. Diverse human activities in such areas directly affect the spatio-temporal dynamic of surface water and its ecological characteristics. Monitoring the surface water dynamic, and understanding the impact of human activities are of great significance for coastal lagoon conservation. The Regional Natural Park of Narbonne includes a typical Mediterranean lagoon complex where surface water dynamic and its potential link with local diverse human activities has not yet been studied. In this context, based on all the available Landsat images covering the study area during 2002-2016, this study identified the water and non-water classes for each satellite observation by comparing three widely used water indices (i.e., NDVI, NDWI and MNDWI) and using the Otsu method. The yearly water frequency index was then computed to present the spatio-temporal dynamic of surface water for each year, and three water dynamic scenarios were also identified for each year: permanent water (PW), non-permanent water (NPW) and non-water (NW). The spatial and inter-annual variation in the patterns of the three water scenarios were characterized by computing the landscape metrics at scenario-level quantifying area/edge, shape, aggregation and fragmentation. Finally, the quantitative link between different land use and land cover (LULC) types derived from the LULC maps of 2003, 2012 and 2015 and the surface water dynamic scenarios was established in each of the 300 m x 300 m grid cells covering the study area to determine the potential impact of human activities on the surface water dynamic. In terms of the inter-annual variation during 2002-2016, PW presented an overall stability, and NPW occupied only a small part of the water surface in each year and presented an inter-annual fluctuation. NPW had a smaller patch size, with lower connectivity degree and higher fragmentation degree. In terms of spatial variation during 2002-2016, NPW often occurred around PW, and its configurational features varied from place to place. Moreover, PW mostly corresponded to natural lagoon, and salt marsh (as a part of lagoons), and NPW had a strong link with arable land (agricultural irrigation) and salt marsh (salt production), sand beach/dune, coastal wetlands and lagoon for the LULC maps of 2003, 2012 and 2015. However, more in-depth analysis is required for understanding the impact of sand beach/dune, coastal wetlands and lagoon on surface water dynamics. This study covers the long-term variations of surface water patterns in a Mediterranean lagoon complex having intense and diverse human activities, and the potential link between LULC types and the water dynamic scenarios was investigated on different dates. The results of the study should be useful for environmental management and protection of coastal lagoons.

The effects of acidic electrolyzed water (AEW) on the microbiological and physicochemical properties of fresh-cut red cabbages were studied. The fresh-cut red cabbages and artificially inoculated red cabbages with Salmonella Typhimurium DT104 were washed with distilled water (DW) and different available chlorine concentration (ACC) of AEW for different times. AEW treatments significantly reduced the populations of native aerobic bacteria, molds and yeasts, and artificially inoculated S. Typhimurium DT104 compared to the DW treated and untreated red cabbage samples. The effectiveness of AEW treatments was greatly enhanced with increasing ACC and treatment times. S. Typhimurium DT104 were not detected in the washing water after the red cabbages treated by AEW. The surface color, pH, and total phenolic contents were did not significantly change when the red cabbages were washed with DW and 100 ppm AEW for 3 min. The anthocyanin contents and antioxidant activities of red cabbage were significantly reduced by 18.5% for cyanidin, 22.1% for pelargonidin, and 11.2% for DPPH radical scavenging activity, the impacts on the nutritional benefits of red cabbage were considered as limited and acceptable. The optimal process condition of AEW for washing red cabbage was 100 ppm for 3 min. In these conditions, most of the native microflora were inactivated, and artificial inoculated S. Typhimurium DT104 on the red cabbage were reduced by 40.2% (3.67 log CFU/g) and with minimal losses of nutrients and antioxidant activity, as well as no requirement of discontinuation treatment on the washing water.

Temperature and pH can expedite the ability of pathogens to cause diseases in cold-water corals (CWCs). The present study employed a combination of histology and polymerase chain reaction diagnostic techniques to investigate potential pathogens present in the CWCs Lophelia pertusa and Madrepora oculata in the Porcupine Bank Canyon (PBC), NE Atlantic. No pathogen was observed in the Madrepora samples. Neither histology nor standard PCR detected Vibrio spp. in the corals, although using Illumina technology, V. shilonii was observed in some L. pertusa samples in low abundances (0.22%). A Rickettsiales-like organisms (RLOs) occurred at a prevalence of 8.0% and at a low infection intensity of 1 - 4. Lophelia showed a few RLOs infection from the PBC canyon head (2.7%) and high infections in the south branch (5.3%). Similarly, unidentified cells observed in L. pertusa from the south branch (4.0%) were more common than those found in the canyon head (1.3%) with a prevalence of 5.3%. Although the route of pathogen infection is unclear, a likely mode of entry could be associated with particulate availability and the feeding strategies of the scleractinian corals. This suggest that L. pertusa invests energy into an enhanced immune function and reduced susceptibility to global pathogens despite a changing ocean environment.

The order Nymphaeales, consisting of three families with a record of eight genera, has gained significant interest from botanists probably due to its position as a basal-angiosperm. The phylogenetic relationships within the order have well been studied and resolved; however, a few controversial nodes still remain in the Nymphaeaceae including the position of the genus Nuphar. The position of the genus Nuphar and the monophyly of the Nymphaeaceae family remain uncertain. This study adds to the increasing number of completely sequenced plastid genomes of the Nymphaeales and applies large chloroplast gene data set in reconstructing the intergeneric relationships within the Nymphaeaceae. Five complete chloroplast genomes were newly generated, including a first one for the monotypic genus Euryale. Using a set of 66 protein coding genes from the chloroplast genomes of 17 taxa, the phylogenetic position of Nuphar was determined and a monophyletic Nymphaeaceae family was obtained with a convincing statistical support from both partitioned and unpartitioned data schemes. Although genomic comparative analyses revealed a high degree of synteny among the chloroplast genomes of the ancient angiosperms, key minor variations were evident particularly in the contraction/expansion of the Inverted Repeat regions and in RNA editing events. Genome structure, gene content and arrangement were highly conserved among the chloroplast genomes.

Reducing the costs of repairing concrete structures damaged due to the appearance of cracks and reducing the number of people involved in the process of their repair is the subject of a multitude of experimental studies. Special emphasis should be placed on research involving industrial by-products, the disposal of which has a negative environmental impact, as is the case in the research presented in this paper. The basic idea was to prepare a mortar with added granulated blast furnace slag from Smederevo Steel Mill and then treat artificialy produced cracks with a Sporosarcina pasteurii DSM 33 suspension under the conditions of sterile demineralized and water from Danube river in order to simulate natural conditions. The results show a bio-stimulated healing efficiency of 32.02% in sterile demineralized water and 42.74% in Danube water already after 14 days. The SEM images clearly show calcium carbonate crystals as the main compound that has started to fill the crack, and the crystals are much more developed under the Danube water conditions. As a special type of research, microscopic images of cracks were classified into those with and without the presence of bacterial culture. By applying convolutional neural networks (ResNet 50), the classification success rate was 91.55%.

Groundwater monitoring and water level predictions have been a challenging issue due to the complexity of groundwater movement. Simplified numerical simulation models have been used to represent the groundwater system; these models however only provide the conservative approximation of the system and may not always capture the local variations. Several other efforts such as coupling groundwater models with hydrological models and using geostatistical methods are being practiced to accurately predict the groundwater levels. In this study, we present a novel application of geostatistical tool on residuals of groundwater model. Kriging method was applied on the residuals of the numerical model (MODFLOW) generated by the TWDB (Texas Water Development Board) for the Edwards-Trinity (Plateau) aquifer. The study was done for the years 1995 through 2000 where 90% of the observation data was used for model simulation followed by cross-validation with the remaining 10% of the observations. The kriging method reduced the average absolute error of approximately 31 m (for MODFLOW simulation) to less than 5 m. Also, the residuals’ average standard error reduced from 9.7 to 4.7. This implies that the mean value of residuals over entire period can be a good estimation for each year separately. The use of kriging technique thus can provide with improved monitoring of groundwater levels resulting in more accurate potentiometric surface maps.

This work aims to investigate systematically the influence of process temperature, bio-mass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale, as well as at 200, 225, and 250 °C, 2 °C/min, bio-mass-to-water ratio of 1:10, in laboratory scale. The elemental composition (C, H, N, S) of solid phase determined to compute the HHV. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas an-alyzer. For the experiments in pilot scale with constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential de-cay with temperature, while that of liquid and gaseous phases a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied be-tween 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total car-boxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentra-tions of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfu-ral, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments in laboratory scale with constant biomass-to-water ratio of 1:10, the yields of solid ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with tem-perature, but also a lower degradation grade. The chemical composition of main organic compounds (furfu-ral, HMF, phenols, cathecol, and acetic acid) dissolved in the aqueous phase in laboratory scale shows the same behavior of those in obtained in pilot scale.

The relationship between Climate Change and Water is an obvious and key issue within the Sustainable Development Goals. This study aims to investigate the social representation created around this relationship in three different territorial contexts in order to evaluate the influence of the territory on the perception of the risk of Climate Change and its relationship with water. By means of a questionnaire completed by 1709 university students, the climatic literacy of the individual was evaluated in order to relate it to other dimensions on the relationship between Climate Change and Water (information, training previous on climate change and pro-environmental attitudes) in their different dimensions in three different territorial contexts. The results show that the socio-cultural context influences the social representation of Climate Change, but not from the climatological condition, so that it is reasonable to think that the social representation of this relationship is favoured by a common culture around this relationship.

A single geological carbon dioxide (CO2) storage within salinity aquifer as a paramount stratagem in the context of forthcoming CO2 sequestration initiatives. Within the expansive tapestry of terrestrial salinity aquifers in China, replete with nuances in mineral composition and structural diversity, a paradigm distinct from the marine sedimentary basins of North America, a labyrinthine stratigraphic environment of elevated complexity unfolds. Consequently, conspicuous lacunae and insufficiencies manifest within the existing knowledge reservoir pertaining to CO2-water-rock (mineral) reaction mechanisms. Notably, a conspicuous dearth of insights prevails concerning the dissolution kinetics inherent to individual minerals embroiled in these reactions. The present investigation undertakes a scrupulous exploration into the dissolution and erosive processes manifest within four emblematic terrestrial minerals in conjunction with CO2. Furthermore, the study meticulously scrutinizes the evolution of ionic composition and pH within the formation water throughout the trajectory of the geochemical reactions. To accomplish this, a simulation apparatus is configured to emulate conditions germane to temperature, pressure, and mineralization characteristics characteristic of a prototypical salinity aquifer reminiscent of the Daqing oilfield in China. The findings that emerge from this scrutiny reveal that the erosive action of CO2 fluid begets varying degrees of dissolution within the four minerals under investigation. Moreover, our meticulous inquiry lays bare that, in the terminal phases of the reaction process, feldspar precipitates secondary minerals, characterized primarily by dawsonite, in response to the aquatic milieu typifying the profound salinity stratum of terrestrial sedimentation. This milieu is notably enriched with Na+ ions and NaHCO3. This phenomenon suggests that feldspar, under these specific conditions, assumes the mantle of a mineral amenable to carbon sequestration, thus enriching the reservoir for CO2 mineralization within the salinity stratum of terrestrial sedimentation.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

Global warming leads in general to a reduction in precipitations and non-rainfall water contributions such as dew. The present study, carried out in Gujarat (India) for 17 years between 2005 and 2021, shows however a rare increase of the rain falls and dew condensation, the latter related to an increase in relative humidity and a decrease in wind amplitudes. Rain was obtained from meteo stations. Dew was calculated from an energy model and meteo data from 15 meteo stations (14 in India and 1 in Pakistan) and compared to early and dedicated measurements in 13 sites. Maps of dew, rain and their relative contributions during the period are provided. They show that, while rain mainly occurs during the monsoon (June to September), dew forms during the dry season (October to April). This water resource was mapped over the Gujarat state of India by using a kriging process. According to the site, the dew/rain ratios can represent between 4.6% (Ahmedabad) to 37.2% (Jamnagar) on the whole period of 17 years. This positive evolution, which is observed since 2015-2017, is likely to continue in the future.

Photoelectrocatalytic water splitting by using various TiO₂ nanostructures is a promising approach to generate hydrogen without harmful byproducts. However, their effective performance is restricted by some drawbacks such as high rapid electron-hole pair recombination and backward reaction producing H₂O. Thus in this study, the probability of enhancing hydrogen generation rate by adding methanol as a sacrificial agent to the anodic chamber of a two-compartment photoelectrochemical cell is investigated. Herein, one-dimensional elongated TiO₂ nanorods that were fabricated via a facile one-pot hydrothermal method are utilized as potent photoanode. Voltammetric characterizations confirm that addition of alcoholic sacrificial agent has a significant effect on photoelectrochemical properties of TiO₂ nanorods which by adding 10 wt% of methanol, the photocurrent density and photoconversion efficiency increased from 0.8mA.cm^-2 to 1.5mA.cm^-2 and from 0.28% to 0.45%, respectively. The results of photoelectrocatalytic water splitting indicated that the hydrogen generation rate in the presence of methanol was about 1.2 times higher than that from pure water splitting. These enhancements can be attributed to the key role of methanol. Methanol molecules not only inhibit the electron-hole pair recombination but also accelerate the hydrogen generation rate by sharing their hydrogen atoms.

This study inscribes itself in the global discussion on the nurturing of pro-environmental behaviors among young people for a sustainable future. Here we focus on students' interest in Ecosystem Services and Sustainability to explain their awareness and optimism about the environmental issues of air pollution, water shortage and green gas emission in 50 countries around the world. To this end, we use the cross-sectional survey data of the OECD's Program for International Student Assessment (PISA) 2015, along with seemingly unrelated bi-variate weighted ordered Probit modeling with country specific effects. The results show that in addition to factors such as age, gender, immigration status, and economic, social and cultural status, interest in the biosphere is a significant determinant of students' environmental awareness and optimism. In fact, a one level increase in students' interest in ecosystem services and sustainability raises on average their awareness level by 15.3% for the issue of air pollution, 15.7% for the issue of water shortage, and 24.6% for the issue of green gas emission. Although students' interest in the biosphere seems to not have a significant effect on their expectations about the issue of green gas emission, it does however raise their level of optimism by 0.8% for the issue of air pollution, and 0.2% for the issue of water shortage. Furthermore, every one level increase in students' environmental awareness leads to 17.3% more optimism about the issue of air pollution, 15.8% more optimism about the issue of water shortage, and 17.4% more optimism about the issue of green gas emission. Therefore, relying on the Theory of Planned Behavior (TPB), our results imply that governments and policy makers can successfully leverage young people interests in the biosphere to effectively achieve their goals for sustainability.

The management of urban water has evolved from single-function systems to more sustainable designs promoting society and nature as inputs to engineer novel infrastructure. In transdisciplinary research, co-design refers to a design thinking strategy in which people jointly frame a problem-solution. This article presents a conceptual framework to assess a case study focusing on the process of co-design and implementation of green infrastructure as a prototype for stormwater management. The evaluation is carried out from a self-reflective post-implementation perspective. Research activities are translated into the framework to evaluate conditions shaping the trajectory of the prototype. As a result, key aspects driving the research regarding levels of stakeholder participation and dimensions of power are identified. Planning resilient co-design strategies to retrofit urban spaces is necessary to avoid unintended consequences, especially at the initial experimental stages. This study aims to contribute to the continuous improvement of pilot strategies in urban spaces by providing a framework for a structured evaluation of research experiences.

Researches are moving to iron and ammonia elimination from ground water. Here, we are using poly acrylic–poly acrylamide hydrogel which grafted with 3-chloroaniline. This copolymer was synthesized by addition polymerization. Effect of agitation time, dosage and adsorbents temperature on the removal process sensitivity has been investigated. The copolymer was described experientially and theoretically. Isothermal, kinetic adsorption models and were discussed. This hydrogel could be regenerated efficiently (98.3%removal of iron and 100% removal of ammonia). Density functional theory DFT method using B3LYP/6-311G(d,p),LANL2DZ level of the theory were managed to investigate stationary states of grafted co-polymer and the complexation energy of the hydrogel with the studied cations. NBO analysis is using DFT to investigate the negative centers on the hydrogel. The complexation energy showed selectively of hydrogel to studied cations.

Seasonal snowpacks, characterized by their snow water equivalent (SWE), play a major role in the hydrological cycle, snow melt contributions to floods and the subsequent availability of water resources downstream. Accurately estimating SWE and understanding its spatial and temporal variations presents a considerable challenge, particularly within mountainous regions characterized by complex terrain and limited observational data. Seeking to enhance the performance of the widely used Soil and Water Assessment Tool (SWAT), we report a new approach characterising snowpack behaviour incorporating both modelled and remotely sensed derived SWE calibration data. We focus on the Chenab River Basin (CRB) a headwater catchment of the Indus Basin, globally significant in terms of human inhabitants and intensifying flood risk due to climate change. We conducted a thorough assessment of five satellite-derived and reanalysis-based precipitation datasets: ERA5-Land, CMORPH, TRMM, APHRODITE, and CPC UPP. This reveals significant levels of uncertainty in global precipitation products when compared to reference data from observed stations as well as in the resulting simulated streamflow from the SWAT model. Subsequently, we expanded the scope of the SWAT model to encompass the spatial and temporal simulation of SWE. This was achieved by incorporating information from remotely sensed and modelled SWE products, manually adjusting snow parameters in R-SWAT for both the main basin and at sub-basin scales. Integrating SWE from reference snow products into the calibration process, alongside streamflow data, substantially enhanced modelling accuracy to simulate SWE compared to the conventional auto-calibration and single-variable approaches reliant solely on streamflow data. This approach results in considerable improvement in SWE predictions and to some extent in streamflow simulation in catchments dominated by snow. This research highlights the potential of remote sensing and modelled SWE parameterisation in the absence of in-situ snowpack data in high-altitude environments. An improved understanding of SWE behaviour is vital for predicting hydrological responses spanning hazards to water resources in the populous downstream regions of the Indus Basin, especially in the face of climate change.

We evaluated the transcriptional response of interferon (IFN)-related genes in rock bream iridovirus (RBIV)-infected rock bream under high-, low-, or no-mortality conditions induced by different stocking water temperatures. Under the high susceptibility condition (group A, water temperature 26 °C, 100% mortality), only the Mx gene was expressed early, with prolonged expression, and with heavy viral loads of approximately 106–107 major capsid protein gene copies/μL from 4 to 10 days post infection (dpi). However, IRF1, IRF3, IRF8, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56 were activated at later time points (8 dpi) and then quickly decreased (10 dpi). For the low susceptibility condition, the water temperature was set at 23 °C for 7 days (group B) and then reduced to 17 °C. Group B exhibited a 28% mortality rate, in which persistent and effective antiviral responses were observed for long periods of time. In particular, at 20 and 22 dpi, when virus replication was peaked at approximately 107/μL, the expressions of most of the IFN-related genes (IRF1, IRF3, IRF8, Mx, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56) were significantly higher in group B than in the control group. Moreover, prolonged and higher levels of IRF3 (at least 30 dpi), IRF8 (at least 30 dpi), ISG15 (at least 30 dpi), PKR (at least 28 dpi), Viperin (at least 30 dpi), and IFI44 (at least 30 dpi) were also observed in the recovery stage of infection. Under the no-susceptibility condition at 17 °C (0% mortality), significantly elevated levels of IRF3, Mx, ISG15, and PKR were observed mostly until 20 dpi. The findings indicate that RBIV infection can induce an efficient IFN-mediated antiviral immune response in low- and no-susceptibility conditions. The findings could be valuable for effective control of viral pathogens in fish.

The Southwest Alpine Canyon Area of China was one of the regions in the world that suffered from severe soil erosion. The focus of this research was to understand the response of land use change on soil loss by water erosion in alpine canyon on Southeast Tibet, we analyzed the characteristics of temporal and spatial dynamics of land use in the Niyang River Basin from 1990 to 2020 using GIS and statistical methods, assessed the spatial and temporal change characteristics of soil erosion in the Niyang River Basin using RUSLE model. For this purpose, the meteorological, soil, topographic, remote sensing data were collected. The results showed the area of cropland and construction land in the Niyang River Basin increased to 2.4 and 6.1 times the original from 1990 to 2020, respectively, the area of forest and water continued to decrease. Grassland, unused land and forest have always been the dominant land types in the Niyang River Basin. Tolerable soil erosion was distributed in the flat areas of the valley terraces in the main stream and its tributaries, slight soil erosion was mainly distributed in the flat areas at high altitudes, and moderate, severe, very severe and destructive soil erosion was sporadically distributed in the Niyang River Basin. The areas of tolerable and slight soil erosion exceeded 82% of the total area, The area of severe, very severe and destructive soil erosion was less than 6%, but the total soil loss amount of severe, very severe and destructive erosion was more than 27%. From 1990 to 2020, the soil erosion area decreased from 9219.34 km2 to 8,090.84 km2 in Niyang River Basin, more than 85% of the soil erosion class has not changed, and the change of total soil loss amount also shows a significant reduction trend as a whole. 99% of the total soil loss amount in the Niyang River basin is generated by grassland, forest and unused land. The conversion of various land use types to cropland will cause the enhancement in soil erosion grade. We recommend that the focus of soil erosion control in the Niyang River Basin is to protect grassland, forest and carry out scientific farming.

River flow prediction is a pivotal task in the field of water resource management during the era of rapid climate change. The highly dynamic and evolving nature of the climatic variables e.g., precipitation has a significant impact on the temporal distribution of the river discharge in recent days making the discharge forecasting even more complicated for diversified water-related issues e.g., flood prediction and irrigation planning. To predict the discharge, various physics-based numerical models are used using numerous hydrologic parameters. Extensive lab-based investigation and calibration are required to reduce the uncertainty involved in those parameters. However, in the age of data-driven predictions, several deep learning algorithms showed satisfactory performance in dealing with sequential data. In this research, Long Short-term Memory (LSTM) neural network regression model is trained using over 80 years of daily data to forecast the discharge time series up to 3 days ahead of time. The performance of the model is found satisfactory through the comparison of the predicted data with the observed data, visualization of the distribution of the errors and Root Mean Squared Error (RMSE) value of 0.09. Higher performance is achieved through the increase in the number of epochs and hyper parameter tuning. This model can be transferred to other locations with proper feature engineering and optimization to perform univariate predictive analysis and potentially be used to perform real-time river discharge prediction.

The optical complexity of coastal waters is mostly caused by the water discharged from land carrying optical components (such as dissolved and particulate matter) into coastal bays and estuaries, and increasing the attenuation of light. This paper aims to investigate the links between in-water optical properties in four Swedish bays (from the northern Baltic proper up to the Bothnian bay) and the land use and land cover (LULC) and the hydrology in the respective catchment of each bay. The optical properties were measured in situ over the last two decades by various research and monitoring groups while the LULC in each bay was classified using the Copernicus Land Monitoring Service based on Landsat 8 and Sentinel-3 data. The absorption coefficient of coloured dissolve organic matter at 440 nm, aCDOM (440), and its spectral slope factor, SCDOM, were mostly correlated to natural land cover classes (Wetland, Meadow) acting as sources of CDOM, while Agricultural and Urban classes seem to act as sinks. The Agricultural class was also found to be a sink for suspended particulate organic matter (SPOM) whilst Coniferous and Mixed Forests as well as Meadows acted as a sources. SPOM seems to mostly originate from Natural classes, possibly due to the release of pollen and other organic matter. Overall, the methods applied here allow for a better understanding of effects of land used and land cover on the bio-optical properties, and thus coastal water quality, on a macroscopic scale.

Drought is one of the most serious abiotic stressors in the environment, restricting agricultural production by reducing plant growth, development, and productivity. To investigate such a complex and multifaceted stressor and its effects on the plants, a systems biology-based approach is necessitated, entailing the generation of co-expression networks, identification of highly-priority transcription factors (TFs) dynamic mathematical modeling, and computational simulations. Here, we studied a high-resolution drought transcriptome of Arabidopsis. We revealed distinct temporal transcriptional signatures and demonstrated the involvement of specific biological pathways. Generation of a large-scale co-expression network followed by network centrality analyses identified 117 TFs that possess critical properties of hubs, bottlenecks, and high clustering coefficients nodes. Dynamic transcriptional regulatory modeling on integrated TF-target and transcriptome datasets uncovered major transcriptional events during the course of drought stress. Mathematical transcriptional simulations allowed us to ascertain the activation status of major TFs as well as the transcriptional intensity and amplitude of their target genes. Finally, we validated our predictions by providing experimental evidence of gene expression under drought stress for a set of four TFs and their major target genes using qRT-PCR. Taken together, we provided a systems-level perspective on the dynamic transcriptional regulation during drought stress in Arabidopsis and uncovered numerous novel TFs that can potentially be used in future genetic crop engineering programs.

This work presents the first evidence that dissolved globular proteins change the arrangement of hydrogen bonds in water, with different proteins showing quantitatively different effects. Using ATR-FTIR (Attenuated Total Reflection – Fourier Transform Infrared) spectroscopic analysis of OH-stretch bands, we obtain quantitative estimates of the relative amounts of the previously reported four subpopulations of water structures coexisting in a variety of aqueous solutions. Where solvatochromic dyes can measure the properties of solutions of non-ionic polymers, the results correlate well with ATR-FTIR measurements. In protein solutions to which solvatochromic dye probes cannot be applied, NMR (Nuclear Magnetic Resonance) spectroscopy was used for the first time to estimate the hydrogen bond donor acidity of water. We found strong correlations between the solvent acidity and arrangement of hydrogen bonds in aqueous solutions for several globular proteins. Even quite similar proteins are found to change water properties in dramatically different ways.

It is crucial to forecast the water demand accurately for supplying water efficiently and stably in a water supply system. In particular, accurately forecasting short-term water demand helps in saving energy and reducing operating costs. With the introduction of the Smart Water Grid (SWG) in a water supply system, the amount of water consumption is obtained in real time through an advanced metering infrastructure (AMI) sensor, which can be used for forecasting the short-term water demand. The models widely used for water demand forecasting include the autoregressive integrated moving average, radial basis function-artificial neural network, quantitative multi-model predictor plus, and long short-term memory. However, there is a lack of research on assessing the performance of models and forecasting the short-term water demand by applying the data on the amount of water consumption by purpose and the pipe diameter of an end-use level of the SWG demonstration plant in each demand forecasting model. Therefore, in this study, the short-term water demand was forecasted for each model using the data collected from the AMI, and the performance of each model was assessed. The Smart Water Grid Research Group installed ultrasonic-wave-type AMI sensors in the block 112 located in YeongJong Island, Incheon, and the actual data used for operating the SWG demonstration plant were adopted. The performance of the model was assessed by using the residual, root mean square error (RMSE), normalized root mean square error (NRMSE), Nash–Sutcliffe efficiency (NSE), and Pearson correlation coefficient (PCC) as indices. The water demand forecast was slightly underestimated in models that employed the assessment results based on the RMSE and NRMSE. Furthermore, the forecasting accuracy was low for the NSE due to a large number of negative values; the correlation between the observed and forecasted values of the PCC was not high, and it was difficult to forecast the peak amount of water consumption. Therefore, as the short-term water demand forecasting models using only time and the amount of water consumption have limitations in reflecting the characteristics of consumers, a water supply system can be managed more precisely if other factors (weather, customer behavior, etc.) influencing the water demand are applied.

Aquathermolysis is a promising method to upgrade heavy oil in reservoir conditions. However, application of catalysts can significantly promote transformation of the heavy fragments (resins and asphaltenes) and heteroatom-containing compounds of crude oil mixture into low-molecular-weight hydrocarbons. In this paper, the comparison study of the catalytic performance of the water-soluble metal salts such as NiSO4 and FeSO4 on the aquathermolytic upgrading of heavy oil samples produced from Ashal’cha reservoir was carried out at a temperature of 300 °C for 24 hours. Iron nanoparticles contributed to the highest viscosity reduction degree - 60% in contrast to the viscosity of the native crude oil sample. The viscosity alteration is reasoned by the changes in the group composition of heavy oil after catalytic (FeSO4) aquathermolysis, where the content of resins and asphaltenes were reduced by 17% and 7%, respectively. Moreover, the aquathermolytic upgrading of heavy oil in the presence of FeSO4 led to an increase in the yield of gasoline fraction by 13% and diesel fraction by 53%. The H/C ratio, which represents the hydrogenation of crude oil, increased from 1.52 (before catalytic upgrading) to 1.99 (after catalytic upgrading). The results of Chromatomass (GC-MS) and Fourier-infrared (FT-IR) spectroscopies confirmed the intensification of destructive hydrogenation of resins and asphaltenes in the presence of the water-soluble catalysts. According to XRD and SEM-EDX results, the metal salts are thermally decomposed during the aquathermolysis process into the oxides of corresponding metals and particularly sulfided by the sulfur-containing aquathermolysis products.

Proton exchange membrane water electrolyzers (PEMWEs) for water electrolysis have received tremendous attention due to their immediate response, high proton conductivity, low ohmic losses and gas crossover rate. However, design high activity, economical and long-term durable electrocatalysts in an acidic environment is still the bottleneck to realize the large-scale commercialization of PEMWEs. Iridium-based materials represent one of the most promising classes of oxygen evolution reaction (OER) catalysts due to their intrinsic stability in acid media over ruthenium-based counterparts. However, only a few innovative approaches have been developed to synthesizing iridium-based catalysts (IBCs) in the past decade, mainly due to achieving high activity may deteriorate the stability of IBCs. Accordingly, various engineering strategies of optimizing IBCs have been proposed to address this issue, including doping engineering, morphology engineering, crystal phase engineering and support engineering. Herein, a critical overview focusing on various synthesis and modulation strategies of IBCs is presented, based on an in-depth understanding of the relationship between electronic structures, charge redistribution and activity as well as stability of the electrocatalysts. In addition, the unprecedented achievements in PEMWEs are summarized. The reaction mechanisms and future perspectives are critically discussed to inspire more rational design of IBCs toward practical applications.

Polluted rivers are a primary problem in Changhua County, Taiwan, due to rapid and massive developments in agriculture and industry. In this study, samples consisted of water influent from the Yangzi-Cuo River, Ci-Tong Jiao, Changhua County. Ecology technology, a combination of gravel contact oxidation and surface flow constructed wetlands, was employed to enhance the water quality. Ecology technology is a useful and ordinary process that focuses on original treatment of pollution through chemical, physical, and biological procedures based on the mediums of soil, plant, water, and microorganisms from pure environments. Moreover, this study aimed to minimize the river pollution index (RPI) of the Yangzi-Cuo River by using combinations of gravel contact oxidation and surface flow constructed wetlands. The inflow volume of the water samples in situ was found to be 1534–2261 cubic meters per day (CMD). The pollution in the water sample mostly involved suspended solid (SS), ammoniacal nitrogen (NH₃–N), total phosphorus (TP), total nitrogen (TN), and biochemical oxygen demand (BOD), and the values of the above indexes were found to be 10.0–26.7 mg/L, 0.9–14.0 mg/L, 1.2–14.1 mg/L, 11.1–18.2 mg/L, and 0.5–3.6 mg/L, respectively. Efficiencies of pollution elimination in SS, NH₃–N, TP, TN, and BOD were found to be 24.2–93.1%, 58.3–86.2%, 5.2–85.0%, 59.4–77.2%, and 46.3–76.4%, correspondingly, after purification treatment via ecology technology. Thus, ecology technology is a valid means of purification treatment for polluted rivers.

Irrigation and fertilization are indispensable links in the jujube planting industry in southern Xinjiang, China. However, the water and fertilizer integration effects on jujube growth and fruit quality remain unclear. A two-year water and fertilizer optimization coupling test was conducted to determine the optimal water- and nutrient-supply scheme. The three-factor randomized block experiment included water (W), nitrogen (N), and phosphorus (P). According to the principal component analysis of each index, each treatment’s comprehensive score was obtained. Using yield and economic regression models, the theoretical value and yield value of the optimal economic benefit are inferred. When W, N, and P were applied together, the fruit quality and yield of each treatment significantly differed, and the vitamin C, soluble sugar, and sugar–acid ratio increased significantly with an increase in nitrogen fertilizer. However, the titratable acid decreased. An increase in irrigation and nitrogen application significantly increased fruit yield. The comprehensive score was the highest in the N3P3W2 treatment, which improved fruit quality, and the lowest in the N4P3W2 treatment. When the amounts of N, P, and W were 275.56 kg·hm-2, 413.66 kg·hm-2, and 7278.19 m3·hm-2, respectively, the theoretical economic benefit was the best. The N4P3W2 treatment is the optimal treatment.

Fourier transform infrared (FTIR) absorption spectroscopy of cold molecules and clusters in supersonic slit jet expansions complements and extends more sensitive action spectroscopy techniques and provides important reference data for the latter. We describe how its major drawback, large substance and carrier gas consumption, can be alleviated by one to two orders of magnitude via direct and continuous recycling of the gas mixture. This is achieved by a combination of dry rotary lobe and screw pump compression. The signal-to-noise ratio is boosted by the established buffered giant gas pulse technique with full interferogram synchronization. The buildup of water impurities typically limits the recycling gain, but is turned into a feature for the study of hydrate complexes of volatile molecules. Continuous operation with a single gas filling over several days becomes practical and useful. Decadic absorbances in the low ppm range are detectable and the mid infrared range can be recorded simultaneously with the near infrared. The less straightforward hydration number assignment of spectral features in direct absorption spectroscopy is supported by a gradual water buildup at a rate of less than 0.5 mg/h. A recent reassignment proposal for the water dimer OH stretching spectrum is refuted and vibrational spectra of vacuum-isolated 18O-water clusters are presented for the first time. Methanol docking on asymmetric ketones is used to illustrate the advantages and limitations of the recycling concept. Previous assignments of the hydrate complex of 1-phenylethanol are confirmed. Additional features of the setup await testing and refinement, but the recycling technique already substantially widens the applicability of direct absorption spectroscopy of neutral molecular clusters. It may be attractive for other high-throughput jet spectrometers.

Riparian restoration is an important objective for landscape managers seeking to redress the widespread degradation of riparian areas and the ecosystem services they provide. This study investigated the long-term outcomes of ‘one-off’ restoration activities undertaken in the Upper Murrumbidgee Catchment, NSW, Australia. The objective of the restoration was to protect and enhance riparian vegetation and control erosion, and consequently reduce sediment and nutrient delivery into the Murrumbidgee River. To evaluate the outcomes 10 years after restoration, rapid riparian vegetation and geomorphological assessments were undertaken at 29 sites spanning the four different restoration methods used (at least five replicates per treatment), as well as at nine comparable untreated sites. We also trialed the use of aerial imagery to compare width of riparian canopy vegetation and projective foliage cover prior to restoration with that observed after 10 years. Aerial imagery demonstrated the width of riparian canopy vegetation and projective foliage cover increased in all restored sites, especially those with native plantings. The rapid assessment process indicated that 10 years after riparian restoration, the riparian vegetation was in a better condition at treated sites compared to untreated sites. Width of riparian canopy vegetation, native mid-storey cover, native canopy cover and seedling recruitment were significantly greater in treated sites compared to untreated sites. Geomorphological condition of treated sites was significantly better than untreated sites, demonstrating the importance of livestock exclusion to improve bank and channel condition. Our findings illustrate the value of ‘one-off’ restoration activities in achieving long-term benefits for riparian health. We have demonstrated that rapid assessments of the vegetation and geomorphological condition can be undertaken post-hoc to determine the long-term outcomes, especially when supported with analysis of historical aerial imagery.

Using co-precipitation to synthesize (CeO2)0.95(Y2O3)0.05 (YDC) and solid reaction method to synthesize (CeO2)0.75(ZrO2)0.25 (ZDC), and the characterization for both crystal structure and micro-structure of the two materials was conducted with X-ray diffraction (XRD) and scanning electron microscope (SEM) methods. Prepare the YDC and ZDC based limited current O2 sensor by employing platinum pasting bonding method. Sensing characteristics of the sensor were obtained at different conditions and study on the impact of temperature, O2 concentration as well as water vapor pressure on the sensing characteristics had been conducted. XRD results show that the phase structure of both YDC and ZDC is cubic phase. SEM results show that both YDC and ZDC layers are dense layers, which are then qualified to be the composition materials of the sensor. This limited current O2 sensor shows good sensing performance and conforms to the Knudsen model. Log(IL•T) depends linearly on 1000/T with R2 of 0.9904, IL depends linearly on x(O2) with R2 of 0.9726 and sensing characteristics are not affected by p(H2O).

Mushrooms have long rich history in folk medicine, traditional and functional foods due to high content of dietary myco-nutrients. Currently, there is increased interest in finding appropriate food-grade green ex-traction systems capable of extracting these bioactive compounds from dietary mushrooms for applica-tions in various food, pharmacological or nutraceutical formulations. Herein, we evaluated a modified Swiss water process (SWP) method using alkaline and acidic pH at low and high temperature under pressurized conditions as a suitable green food grade solvent to obtained extracts enriched with my-co-nutrients (dietary phenolics, total antioxidants (TAA), vitamins, and minerals) from Chaga. Ultra-high performance liquid chromatography coupled to high resolution accurate mass tandem mass spectrometry (UHPLC-HRAMS-MS/MS) was used to assess the phenolic compounds and vitamin levels in the extracts, while inductively coupled plasma mass spectrometry (ICP-MS) was used to determine the mineral con-tents. Over twenty phenolic compounds were quantitatively evaluated in the extracts and the highest total phenolic content and antioxidant activity was observed at pH11.5 at 100°C. The most abundant phenolic compounds present in Chaga extracts included phenolic acids such as protocatechuic acid 4-glucoside (0.7-1.08µg/mL), syringic acid (0.62-1.18µg/mL), and myricetin (0.68-1.3µg/mL). Vitamins are being reported for the first time in Chaga. pH 2.5 at 100°C treatment shows superior effects in extracting the B vitamins whereas pH 2.5 at 60 and 100°C treatments were outstanding for extraction of total fat-soluble vitamins. Vitamin E content was the highest for the fat-soluble vitamins in the Chaga extract under acidic pH (2.5) and high temp. (100°C) and ranges between 50 to 175 µg/100g Chaga. Antioxidant minerals ranged from 85.94 µg/g (pH7 at 100°C) to 113.86 µg/g DW (pH2.5 at 100°C). High temperature 100°C and a pH of 2.5 or 9.5. The treatment of pH11.5 at 100°C was the most useful for recovering phenolics and antioxidants from Chaga including several phenolic compounds reported for the first time in Chaga. SWP is being proposed herein for the first time as a novel, green food-grade solvent system for the extraction of myco-nutrients from Chaga and have potential applications as a suitable approach to extract nutrients from other matrices. Chaga extracts enriched with bioactive myconutrients and antioxidants may be suitable for further use or applications in the food and nutraceutical industries.

In this paper, mesoporous electrodes consisted of Sb-doped SnO2 deposited onto Ti plates controlled corroded under acidic medium were synthesized by spin-coating method, and morpho structurally characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrodes were electrochemical testing in the degradation/mineralization by electrooxidation (EO) of doxorubicin (DOX) as single-component and multi-component together with capecitabine (CCB)-from cytostatic class and humic acid (HA)-from natural organic matter (NOM) class in the absence/the presence of activated carbon (AC) as particulate electrode. The best mineralization efficiency of 67 % was achieved for DOX mineralization using Sb-doped SnO2 deposited onto Ti plate controlled corroded with oxalic acid in electrooxidation process. The presence of AC within the electrolysis process generated a synergy effect of 52.75 % for TOC parameter removal, which is in accordance and quite better than the result reported in the literature. The aspects related to the complex mechanism of DOX degradation and mineralization are discussed. The superiority of AC assisted electrooxidation, as electrochemical filtering (EF), was proved considering simultaneous degradation and mineralization of mixture of doxorubicin, capecitabine and humic acid.

Geo-information about the spectral variability of the water-leaving radiance is the key to the validation of satellite and in situ measurements and the development of regional algorithms. In this study, using cluster analysis, five trends were identified that are characteristic of various phenomena in the northwestern part of the Black Sea (summer and winter blooms, turbid waters, river runoff). Typical values of the remote sensing reflectance coefficient are calculated for each case. Additionally, the standard values of the color indices for each cluster are calculated. It is shown that the ratio of the color index CI(412/443 nm) is slightly variable and equals 0.8±0.07.This can be a reference point for recovering incorrect (negative) satellite Rrs(λ) values in the shortwave region. In a similar way, the color index was calculated according to the MODIS and VIRS data, it was shown that on days with a turbid atmosphere (high AOT values), the standard deviation of the color index is 30%. For days with a clear atmosphere, the color index is close to the in situ results.

The main focus of this work is to extend the knowledge about the complexity of issues of oxidative stress. Natural compounds play a serious role in multiple aspects of both human, leading to clear health-promoting effects. This work is focused on the potential application cosmetic formulations containing including but not limited to of clove water and isolated clove oils on their aid in the control of the diseases. The aim of our work was to prepare to evaluate cosmetic formulations containing clove oil, eugenol or new eugenol ester derivative (eugenyl dichloroacetate - EDChA) but also cosmetic formulations containing the aqueous phase obtained after separation of essential oil following the clove buds steam distillation. To evaluate the antioxidants transdermal delivery system, in vitro permeation experiments in a Franz diffusion cell were performed using pig skin. The antioxidative capacity of the cosmetic formulations obtained was determined by the DPPH free radical reduction method. In the next stage, the antioxidant activity (DPPH, ABTS, and Folin–Ciocalteu methods) of the fluid that penetrated through pig skin and of the fluid obtained after skin extraction, were also evaluated. For comparison, studies of cosmetic formulation containing alone dichloroacetic acid (DChAA) were as well carried out. The obtained cosmetic formulations were characterized by of antioxidant activity estimated after 24 hours of conducting the experiment, which indicates long-term protection against reactive oxygen species (ROS) in the deeper layers of the skin. The results of this work contribute to the development of cosmetic formulations with antioxidant potential, emphasizing that the water phases are waste from the process of cloves steam distillation and are not used to prepare cosmetic formulations. The use of waste water from the clove buds steam distillation process is environmentally friendly and not allows us to waste, containing however valuable biologically active compounds (furfural, methyl salicylate, 4-allilofenol, eugenol, α- and β-caryophyllene, eugenyl acetate, β-caryophyllene oxide). Together, these results suggest that cosmetic formulations may be potential drug candidates for chemopreventive, antineoplastic and antimutagenic therapy.

In an attempt to improve the quality of the agricultural drain in Egypt for its reuse again in the irrigation, low cost solution such as sand filter along with/ without other filtration media have been used in this research, As a result of that, pilot plant of sand filter mixed with other filtration media was tested for its ability to improve the sand performance in removing the suspended solids and organic matters from agricultural drain water of the Belbeis drain (in Sharkia governorate in Egypt). Only sand compared with sand with sponge and sand with Liyan Nanfang activated carbon (L.N.A.C) have been tested to find the optimum mixing sand/ medium ratio &optimum infiltration rate. The work has been done on four runs. It was found that sand mixed with sponge gave the best removal efficiency compared to that of the sand only and the sand mixed with L.N.A.C. The results presented that the concentration of CODt, CODsol and TSS was reduced from 125, 47 and 162 mg/l to 44, 34 and 28 mg/l respectively at optimum infiltration rate of 2 m³/m²/d for sand mixed with sponge.

Relying on Random Utility Theory (RUT) as the guiding mechanism for the Data Generating Process (DGP), this paper uses households consumption choices on cooking fuel, drinking water, and sanitation from the 2014 United States Agency for International Development's (USAID) Demographic and Health Survey (DHS) data on Burkina Faso, to characterize and investigate the inter-linkages between health consciousness and environmental consciousness, and their relationship with wealth in a low income country context. We achieve this by specifying sequentially three econometric modeling frameworks: the first one being independent binary probit (IBP) models to describe each choice process, followed by a fully parametric trivariate probit (FPTP) model to account for choice dependency, and finally by a semi-parametric trivariate probit (SPTP) model to further relax the linearity assumption. Based on the Akaike Information criteria (AIC) and the estimated Trivariate model correlation coefficients, the SPTP framework is found to be the best specification for describing the observed consumption behaviors. The results show that increased wealth level raises households health and environmental consciousness, while leaving the relative preference ordering over the elements in the household consumption basket unchanged.

Bisphenol A is a remarkable chemical compound for its many applications mainly in the plastics industry, but also for its toxic effects on the environment and human health. BPA (4,4-isopropylidenediphenol) is an anthropogenic compound, moderately soluble in water (120 – 300 mg/l) at room temperature, and highly soluble in alkaline solutions, ethanol and acetone. BPA can bioconcentrate, bioaccumulate and biomagnify through food webs until it reaches humans. To prevent this, effective strategies are sought to allow its removal from the environment, through physico-chemical or enzymatic methods, advanced oxidation, adsorption and biodegradation, ultrasonic degradation. This article shows a comparative study regarding adsorption of BPA on Active carbon and zeolitic tuff, ZTC. In this paper, the characterization of the zeolitic tuff Rupea adsorbent, was carried out from an elemental and mineralogical point of view, pore size and elemental distribution, using SEM, EDAX, and XRD analysis. The pore size varies from 30 nm to 10 µm, atomic ratio Si/Al≥4, and the 80 % of mineralogical composition represent Ca Clinoptilolite zeolites Ca Clinoptilolite zeolite ((Na1.32K1.28Ca1.72Mg0.52)(Al6.77Si29.23O72)(H2O)26.84). Also, a comparative study of the adsorbtion capacity of bisphenol A from synthetic solutions on activated carbon type - Norit GAC 830 W, GAC, as well as on Clinoptilolite-type zeolitic tuff, ZTC, Rupea, was carried out. The experiments were carried out at a temperature of 20 ºC, a pH of 4.11; 6.98 and 8.12, and ionic strength being assured using KCl of 0.01 M, and 0.1 M. The adsorption capacities of GAC and ZTC tend to 115 mg/g and 50 mg/g respectively, at 8.12 pH and ionic strength of 0 M. The Langmuir mathematical model most faithfully describes the adsorption equilibrium of BPA. The maximum adsorption capacity for both adsorbents increases with increasing pH, and decreases with increasing ionic strength.

Water, soil/sediment, and 36 fish samples were collected at three major sites along Flint Creek in 2015-2016 and analyzed for total organic carbon (TOC), dissolved organic carbon (DOC), total mercury (tHg), and other water quality indicators. This study was a follow-up to a 2012 study that revealed elevated tHg levels in fish, resulting in a public health advisory. This study revealed tHg concentrations in water below the detection limit (0.0002 ppm); while, tHG in soil/sediment ranged from < 0.0133 ppm to 0.0682 ppm dry weight. No temporal trends existed, but tHG tended to increase with TOC. Mercury levels in sediment were below the threshold effects level suggested as a preliminary screening level by the National Oceanic and Atmospheric Administration (acute = 1.4, chronic = 0.77 ppb). In summary, tHg levels were low; posing little risk to drinking water. Soil/sediment levels were generally higher and could pose risk to aquatic species.

The Latin American Giant Observatory (LAGO) is a ground-based extended cosmic rays observatory designed to study transient astrophysical events, the role of the atmosphere on the formation of secondary particles, and space-weather-related phenomena. With the use of a network of Water Cherenkov Detectors, LAGO measures the secondary particle flux, a consequence of the interaction of astroparticles impinging on the Earth with the atmosphere. These interactions yield a flux of secondary particles that can be grouped into three distinct basic constituents: the electromagnetic, muonic, and hadronic components. In this work we extend our previous research by using detailed simulations of the expected atmospheric response to the primary flux and the corresponding response of our WCDs to atmospheric radiation. After implemented OPTICS, a density-based clustering algorithm, to identify patterns in data collected by a single WCD, we have further refined our approach by implementing a method that categorizes and differentiates particle groups using advanced unsupervised machine learning techniques. Our analysis demonstrates that applying our enhanced methodology can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout LAGO distributed detection network and other astroparticles observatories for semi-automated, onboard and real-time data analysis. When a particle enters a Water Cherenkov Detector (WCD), it generates a measurable signal characterized by unique features correlating to the particle’s type and the detector’s specific response. The resulting charge histograms from these signals provide valuable insights into the flux of primary astroparticles and their key characteristics. However, this data is insufficient to effectively distinguish between the contributions of different secondary particles. This research extends our previous investigations, wherein we implemented OPTICS, a density-based clustering algorithm, to identify patterns in data collected by a single WCD. We have further refined our approach by implementing a method that categorizes and differentiates particle groups using advanced unsupervised machine learning techniques. This methodology facilitates the differentiation among particle types and utilizes the detector’s nuanced response to each particle type, thus pinpointing the principal contributors within each group. In this work, we utilize OPTICS to analyze simulated data, further validating the proposed method. We created a simulated dataset by combining the outputs of the ARTI and MEIGA frameworks. This dataset simulates the expected WCD signals produced by the flux of secondary particles during one day at the LAGO site in Bariloche, Argentina, situated at 865 meters above sea level. To achieve this, real-time magnetospheric and local atmospheric conditions for February and March of 2012 were analyzed, and the resultant atmospheric secondary-particle flux was integrated into a specific MEIGA application featuring a comprehensive Geant4 model of the WCD at this LAGO location. The output from MEIGA was modified for effective integration into our machine learning pipeline. Our analysis demonstrates that applying our enhanced methodology can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout the LAGO distributed detection network for semi-automated, onboard and real-time data analysis. Our analysis demonstrates that OPTICS can accurately identify the originating particle with a high degree of confidence on a single-pulse basis, highlighting its precision and reliability. These promising results suggest the feasibility of implementing machine-learning-based models throughout the LAGO distributed detection network for semi-automated, onboard data analysis.

Two different silica conformations (Xerogels and Nanoparticles) both formed by the mediation of dendritic poly (ethylene imine) were tested at low pHs on the problematic uranyl cation sorption. The effect of crucial factors i.e., temperature, electrostatic forces, adsorbent composition, accessibility of the pollutant to the dendritic cavities and MW of the organic matrix was investigated to conclude the optimum formulation for water purification under these conditions. This was attained with the aid of UV-Visible and FTIR spectroscopy, dynamic light scattering (DLS), ζ-potential; Brunauer–Emmett–Teller (BET) porosimetry, Thermo Gravimetric Analysis (TG) and Scanning Electron Microscopy (SEM) Results highlighted that both adsorbents have extraordinary sorp-tion capacity. Xerogels are cost-effective since they approximate the performance of na-noparticles with much lesser organic content. Furthermore, they are more practicable materials since they may penetrate the pores of a metal or ceramic solid substrate in the form of a precursor, gel-forming solution.

Modeling the reaction time required for the removal of chemical oxygen demand (COD) from wastewater is important because can be an indicator of harmful pollutants that may pose risks to human health.. Here, we evaluate the use of an inverse artificial neural network (ANNi) to optimize the removal of COD from aqueous herbicide solutions using sonophotocatalysis as the treatment process.. This algorithm takes the operating conditions as input and estimates the optimal reaction time to reach the required effluent COD. This model was validated by comparison with both experimental measurements and simulated analysis, resulting in low error (0.5%), high Pearson correlation (R2 = 0.9956), and short computing time (less than one minute). The results for the proposed methodology (ANNi-GAs) were efficient and attractive in a reasonable way providing a satisfactory picture of the relationships between the optimal input parameters. Such parameters control the degradation process of herbicides online and can be used to predict the behavior of COD removal, thus taking actions to reduce the impact of aqueous treatment with alazine and gesaprim herbicides on aquatic, soil biota, and human health. Therefore, this technique constitutes a promising framework for predicting the environmental impact of herbicides within a tolerable degree of error.

Droughts have a substantial effect on water resources, agriculture, and ecosystems on a worldwide scale. In the Mekong Delta of Vietnam, droughts exacerbated by climate change are significantly endangering the region's agricultural sustainability and output. Conventional forecasting techniques frequently do not capture the intricate dynamics of meteorological phenomena associated to drought effectively, prompting the exploration of more advanced methodologies. This work utilises artificial intelligence, par-ticularly machine learning methods like Gradient Boosting and Extreme Gradient Boosting (XGBoost), to enhance drought pre-diction in the Mekong Delta. The study utilises data from 11 meteorological stations spanning from 1990 to 2022 to create and evaluate Machine Learning models based on several climatic factors. We utilise Gradient Boosting and XGBoost algorithms to estimate the Standardised Precipitation-Evapotranspiration Index (SPEI) and evaluate their effectiveness in comparison to con-ventional forecasting techniques. The results show that Machine Learning, particularly XGBoost, surpasses traditional approaches in predicting SPEI accuracy at various time scales. XGBoost demonstrates skill in understanding the complex relationships between climatic factors, with R² values falling between 0.90 and 0.94 for 1-month forecasts. The progress highlights the potential of Machine Learning in improving drought management and adaptation tactics, proposing the incorporation of Machine Learning forecasting models into decision-making processes to enhance drought resistance in susceptible areas.

Groundwater is a vital resource for human welfare. However, due to various factors, groundwater pollution is one of the main environmental concerns facing. Yet, it is challenging to simulate groundwater quality dynamics due to the insufficient representation of nutrient percolation processes in the soil and Water Assessment Tool model. The objectives of this study were extending the SWAT module to predict groundwater quality. The results proved a linear relationship between observed and calculated groundwater quality considering No3 and TDS with R2, NSE and PBIAS values in the satisfied ranges, albeit underestimation and overestimation were observed due to limited data availability. These results highlight that nitrate and TDS concentrations and variability in groundwater may used as a tool in surface water quality that have to be assumed for designing adaptive management scenarios. Hence, extended SWAT model could be a powerful tool for future regional to global scale modelling of nutrient loads supporting effective surface and groundwater management.

In this research, an attempt was made to reduce the dimension of wavelet-ANFIS/ANN (artificial neural network/adaptive neuro-fuzzy inference system) models toward reliable forecasts as well as to decrease computational cost. In this regard, the principal component analysis was performed on the input time series decomposed by a discrete wavelet transform to feed the ANN/ANFIS models. The models were applied for dissolved oxygen (DO) forecasting in rivers which is an important variable affecting aquatic life and water quality. The current values of DO, water surface temperature, salinity, and turbidity have been considered as the input variable to forecast DO in a three-time step further. The results of the study revealed that PCA can be employed as a powerful for dimension reduction of input variables and also to detect inter-correlation of input variables. Results of the PCA-Wavelet-ANN models are compared with those obtained from Wavelet-ANN models while the earlier one has the advantage of less computational time than the later models. Dealing with ANFIS models, PCA is more beneficial to avoid Wavelet-ANFIS models creating too many rules which deteriorate the efficiency of the ANFIS models. Moreover, manipulating the Wavelet-ANFIS models utilizing PCA leads to a significant decreasing in computational time. Finally, it was found that the PCA-Wavelet-ANN/ANFIS models can provide reliable forecasts of dissolved oxygen as an important water quality indicators in rivers.

Flushing tap water is often promoted as a simple and low cost approach to reducing water lead exposures. This study evaluated lead reduction when prevailing flush guidelines (30 seconds-2 minutes) are implemented in a city compliant with lead-associated water regulations (New Orleans, LA). Water samples (n=1,497) collected from a convenience sample of 376 residential sites (2015-2017) were analyzed for lead in samples collected: at 1) first draw (n=375), and after incremental flushes of 2) 30-45 seconds (n=375), 3) 2.5-3 minutes (n=373), and 4) 5.5-6 minutes (n=218). There was no significant reduction when compared to the first draw lead level, until the 6 minute flush (p<0.05); but most sites (52%) still had detectable lead (≥1 ppb) after 6 minutes. Older homes (pre-1950) and low occupancy sites had significantly higher WLLs (p<0.05).Each sample type had health-based standard exceedances at over 50% of sites sampled (max: 58 ppb). While flushing is an effective short-term approach to remediate high lead, prevailing flush recommendations are an inconsistently effective exposure prevention measure that can often inadvertently increase exposures. Public health messages should be modified to ensure appropriate application of flushing for specific cities, while acknowledging its short-comings and practical limitations.

A paddle wheel aerator is developed in this research, which includes a wireless sensor network for measuring the water quality in the aquaculture of marine shrimp ponds. It can also move to the desired position to fill oxygen and measure water quality. A basic requirement is good standard water quality to prevent shrimp from epidemics and improve production. The water quality paddle wheel aerator applies a microcontroller and sensors to measure eight parameters of water quality. These water quality parameters are observed on the web application via an IoT module. The movement system of the water-quality paddle wheel aerator consists of a LiDAR, GPS, and remote RF signal. Each item of data is recorded immediately on the cloud server while the water-quality paddle wheel moves in the marine shrimp farm. The controlled paddle wheel aerator is harnessed automatically to enhance precisely the spatial monitoring resolution of the measurement system installed, which is needless for a multiple measurement system with high cost of investment. Also, farmers can access real data through the Line application. Hence, they are able to plan and control a good environment for aquaculture, preventing the occurrence of various epidemics and decomposing organic matter in the pond.

(1) Background: The definition of value addition is based on the process or processes which are used to transform physically the initial raw material in the final food or non-food article. Diversification can enhance the possibility of increased gains. The aim of this work is to give a reliable description of value addition when speaking of coconut-based beverages among all possible derivatives; (2) Methods: a systematic review of main papers on the argument has been critically examined and discussed; (3) Results: Processing degree is a consequence of consumers’ requests. Three different drivers for value addition have been considered: packaging, durability, and size options; sensorial features; and sustainability. Results of this investigation have highlighted the added value of several products because of recyclable packaging materials, intermediate or long durability expectations, different available sizes, and good or excellent sensorial performances; (4) Conclusions: There are different value-added coconut-based beverages with interesting perspectives. On the other side, sustainability and eco-friendly policies may be a problem for those products which are produced similarly to non-coconut based beverages. The opportunity of certified organic and/or fair-trade products could help the industry of coconuts in the next future. More research is still needed in this ambit.

The accuracy of estimating changes in terrestrial water storage (TWS) using Gravity Recovery and Climate Experiment (GRACE) level-2 products is limited by the leakage effect resulting from post-processing and the weaker signal magnitude in adjacent areas. TWS anomaly in Dnieper River basin, where characteristic with medium scale and adjacent weak TWS anomaly, is estimate in this work. Two categories of leakage error repaired method (including forward modeling, Data-driven, single and multiple scaling factor) are employed. Root mean square error (RMSE) and Nash-Sutcliffe Efficiency (NSE) are used to evaluate the efficiency of methods. Compare to independent methods, TWS anomaly inverted by multiple scaling factor depending on CPC Soil Moisture model is more accurate in terms with RMSE 2.32 and NSE 0.88, which scaling factors corresponding to trend term 1.02, annual term 1.04, and semi-annual term 1.14. Further, comprehensive climate insights behind of the TWS anomaly were confirmed. The temperate continental climate of this River basin is shown, according to the variation of TWS anomaly in spatial domain. Snowmelt is significant role in TWS anomaly of Dnieper River basin, which is accord with the precipitation record and the 14 years temperature spatial distribution of February. Overall, we compare TWS anomaly recovered by single and multiple scaling method, the leakage signal originates mainly from semi-annual term of the TWS anomaly.

As the core components of water jet propulsion system, water jet pump, directly affect the ship's propulsion performance. 3D reverse design method can effectively suppress the impeller secondary flow to get better performing hydraulic models. Aiming at fast and efficient optimization of the impellers, we parameterize the impellers and runner, and coupled with optimization algorithms and numerical calculations. It is an efficient and feasible way to coupling optimization based on multi-parameter, multi-objective and optimization algorithms, and parameterizing the impellers and guide vane geometry based on the 3D model designed by 3D reverse design method. In this paper, the waterjet propulsion pump is taken as the research object. According to the design method of the waterjet propulsion pump hydraulic model, the traditional axial flow blade design method, the modern ternary design theory of the blades, and the parametric three-dimensional reverse design method are selected to constructing an optimal design optimization strategy for the impeller of water-jet propulsion pump based on multi-parameter and multi-object genetic algorithm. Under the design conditions, the optimized pump efficiency reaches 89.28%, which is 1.24% higher than the original hydraulic model. The optimized pump head is 13.51 m, which is 0.39m more than the original hydraulic model. Under the design condition, the test measured head is 13.26m, the numerical calculation result is 1.88% higher than the test result, the test measured efficiency is 87.1%, the numerical calculation result is 2.5% higher than the test result. From the test results, the optimized impeller has higher hydraulic performance. Experiments have shown that it is feasible to optimize the design strategy.

This research aims to develop an inexpensive ocean observation instrument with a project name is NOBEL (Nusantara Oceanography Backdoor Experiment Laboratory)-BOX. The device can be installed on all types of vessels and placed in a specific area to map the water conditions, providing accurate data for managing a marine area specifically to water quality. The principle of NOBEL-BOX is to attach sensors in a container connected to a microcontroller and then measure directly. The method employed includes experimental design, laboratory and field tests, and data evaluation to produce the necessary system and instruments. The design process involves the construction of the instrument and the fabrication of the device. This process includes creating three-dimensional sketches/drawings, designing microcontrollers and data transmission systems, and power capacity. The sensors attached to this device are surface water temperature, air temperature, salinity, dissolved oxygen, pH, and TDS. The testing phase includes data validation, testing of the device in the laboratory, and field testing. The laboratory and field tests showed that the device worked and provided data that can be used to analyze the seawater condition spatially and over time.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

Declining water supply is the main cause of rising water fee for agricultural use. Moreover, in non-technical irrigation, poor irrigation infrastructure exacerbates water scarcity. Thus, the purpose of this study is to identify farmer willingness to pay for non-technical irrigation and its determinants. Structured questionnaire was used to collect data from 100 farmers. Contingent valuation method was employed to elicit farmer WTP and multiple linear regression was used to find its determinants. The result shows that farmer average WTP is Rp 3,055,168 /ha/year. It accounts for 20 percent of total farmer revenue and almost 20 times fee for technical irrigation. Economic and technical variables are the significant determinants of WTP while social variables seem insignificant to WTP. This result indicates high economic value of water, and to improve irrigation management we recommend establishing irrigation infrastructure gradually by mobilizing farmer resources (capital and management) and strengthening WUA.

The COVID-19 pandemic is adversely impacting food and nutrition security and requires urgent attention from policymakers. Sustainable intensification of agriculture is one strategy that attempts to increase food production without adversely impacting the environment, by shifting from water-intensive crops to other climate-resistant and nutritious crops. This paper focuses on the Indian state of Andhra Pradesh by studying the impact of shifting 20% of the area under paddy and cotton cultivation to other crops like millets and pulses. Using FAO’s CROPWAT model, along with monsoon forecasts and detailed agricultural data, we simulate the crop water requirements across the study area. We simulate a business-as-usual base case and compare it to multiple crop diversification strategies using various parameters – food, calories, protein production, as well as groundwater and energy consumption. Results from this study indicate that reduced paddy cultivation decreases groundwater and energy consumption by around 9-10%., and a calorie deficit between 4-8% - making up this calorie deficit requires a 20-30% improvement in the yields of millets and pulses. We also propose policy interventions to incentivize the cultivation of nutritious and climate-resistant crops as a sustainable strategy towards strengthening food and nutrition security while lowering the environmental footprint of food production.

The prevalence of corona virus and the novel COVID-19 disease in the entire globe has exacerbated different impact on socioeconomic spectrum in the world, including water use pattern. Thus a research was conducted to examine the comparative use of water during pre- and post-COVID-19 lockdown pattern among post-primary schools in Iwo, Osun State, Nigeria. A survey was conducted among fifteen schools which were randomly selected, but with eight public and seven private schools for the investigation. Both descriptive and inferential statistical techniques were used in data analysis. The results revealed that the major source of water to the schools investigated is ground water which is obtained through hand-dug wells and boreholes. It was further discovered that there was increase in water use during post-COVID-19 lockdown era as a result of the directive by the government that clean water should be provided for hand-washing by all schools regardless of the owner to curtail the spread of COVID-19 disease in the country. One sample t-test also revealed that there was a significant difference in water use at (p<0.01) level. It is recommended that the government and other stakeholders in water sector to ensure that all-time and non-seasonal dependent source of water be provided rather than ground water source which is susceptible to variations in water yields from seasonal variations. This will enable continuous clean water supply, for all purposes, including COVID-19 protocols.

Water borne pathogens present a threat to human health and their disinfection from water poses a challenge, prompting search for newer methods and newer materials. Disinfection of Gram-negative bacterium Escherichia coli and Gram-positive coccal bacterium Staphylococcus aureus in aqueous matrix was achieved within 60 and 90 minutes respectively at 35⁰C using solar-photocatalysis mediated by sonochemically synthesized Ag@ZnO core-shell nanoparticles. The efficiency of the process increased with increase in temperature and at 55⁰C the disinfection could be achieved in 45 and 60 min respectively for the two bacteria. A new ultrasound assisted chemical precipitation technique was used for the synthesis of Ag@ZnO core-shell nanoparticles. The characteristics of the synthesized material were established using physical techniques. The material remained stable even at 400o C. Disinfection efficiency of the Ag@ZnO core-shell nanoparticles was confirmed in case of real world water samples from pond, river, municipal tap and was found to be better than that of pure ZnO and TiO2 (Degussa P25). When the nanoparticle based catalyst was recycled and reused for subsequent disinfection experiments, its efficiency did not change remarkably even after three cycles. The sonochemically synthesized Ag@ZnO core-shell nanoparticles have a good potential for application in solar photocatalytic disinfection of water borne pathogens.

In contrast to “frank” pathogens, like Salmonella entrocolitica, Shigella dysenteriae, and Vibrio cholerae, that always have a probability of disease, “opportunistic” pathogens are organisms that cause an infectious disease in a host with a weakened immune system and rarely in a healthy host. Historically, drinking water treatment has focused on control of frank pathogens, particularly those from human or animal sources (like Giardia lamblia, Cryptosporidium parvum, or Hepatitis A virus), but in recent years outbreaks from drinking water have increasingly been due to opportunistic pathogens. Characteristics of opportunistic pathogens that make them problematic for water treatment include: 1) they are normally present in aquatic environments, 2) they grow in biofilms that protect the bacteria from disinfectants, and 3) under appropriate conditions in drinking water systems (e.g., warm water, stagnation, low disinfectant levels, etc.) these bacteria can amplify to levels that can pose a public health risk. The three most common opportunistic pathogens in drinking water systems include Legionella pneumophila, Mycobacterium avium, and Pseudomonas aeruginosa. This report focuses on these organisms to provide information on their public health risk, occurrence in drinking water systems, susceptibility to various disinfectants and other operational practices (like flushing and cleaning of pipes and storage tanks). In addition, information is provided on a group of nine other opportunistic pathogens that are less commonly found in drinking water systems, including Aeromonas hydrophila, Klebsiella pneumoniae, Serratia marcescens, Burkholderia pseudomallei, Acinetobacter baumannii, Stenotrophomonas maltophilia, Arcobacter butzleri, and several free-living amoebae including Naegleria fowleri and species of Acanthamoeba. The public health risk for these microbes in drinking water is still unclear, but in most cases, efforts to manage Legionella, mycobacteria, and Pseudomonas risks will also be effective for these other opportunistic pathogens. The approach to managing opportunistic pathogens in drinking water supplies focuses on controlling the growth of these organisms. Many of these microbes are normal inhabitants in biofilms in water, so the attention is less on eliminating these organisms from entering the system and more on managing their occurrence and concentrations in the pipe network. With anticipated warming trends associated with climate change, the factors that drive the growth of opportunistic pathogens in drinking water systems will likely increase. It is important, therefore, to evaluate treatment barriers and management activities for control of opportunistic pathogen risks. Controls for primary treatment, particularly for turbidity management and disinfection, should be reviewed to ensure adequacy for opportunistic pathogen control. However, the major focus for the utility’s opportunistic pathogen risk reduction plan is the management of biological activity and biofilms in the distribution system. Factors that influence the growth of microbes (primarily in biofilms) in the distribution system include, temperature, disinfectant type and concentration, nutrient levels (measured as AOC or BDOC), stagnation, flushing of pipes and cleaning of storage tank sediments, and corrosion control. Pressure management and distribution system integrity are also important to the microbial quality of water but are related more to the intrusion of contaminants into the distribution system – rather than directly related to microbial growth. Summarizing the identified risk from drinking water, the availability and quality of disinfection data for treatment, and guidelines or standards for control showed that adequate information is best available for management of L. pneumophila. For L. pneumophila the risk for this organism has been clearly established from drinking water, cases have increased worldwide, and it is one of the most identified causes of drinking water outbreaks. Water management best practices (e.g., maintenance of a disinfectant residual throughout the distribution system, flushing and cleaning of sediments in pipelines and storage tanks, among others) that have been shown to be effective for control of L. pneumophila in water supplies. In addition, there are well documented management guidelines available for the control of the organism in drinking water distribution systems. By comparison, management of risks for Mycobacteria from water are less clear than for L. pneumophila. Treatment of M. avium is difficult due to its resistance to disinfection, the tendency to form clumps and attachment to surfaces in biofilms. Additionally, there are no guidelines for management of M. avium in drinking water and one risk assessment study suggested a low risk of infection. The role of tap water in the transmission of the other opportunistic pathogens is less clear and in many cases actions to manage L. pneumophila (e.g., maintenance of a disinfectant residual, flushing, cleaning of storage tanks, etc.) will also be beneficial in helping to manage these organisms as well.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

Water electrolysis is a compelling technology for the production of environmentally-friendly hydrogen, minimizing carbon emissions. The electrolysis process of water heavily relies on the effective and steady oxygen evolution reaction (OER) taking place at the anode. Herein, we in-troduce a highly promising catalyst for OER called CoSe2@NiFeOOH arrays, which are supported on a nickel foam. This catalyst, referred to as CoSe2@NiFeOOH/NF, is fabricated through a two-step process involving the selenidation of a Co-based porous metal organic framework and subsequent electrochemical deposition on a nickel foam. The CoSe2@NiFeOOH/NF catalyst demonstrates outstanding activity for the OER in an alkaline electrolyte. It exhibits a low over-potential (η) of 254 mV at 100 mA cm−2, a small Tafel slope of 73 mV dec−1, and excellent high stability. The high performance of CoSe2@NiFeOOH/NF can be attributed to the combination of the high conductivity of the inner layer and the synergistic effect between CoSe2 and NiFeOOH. This study offers an effective method for the fabrication of highly efficient catalysts for the OER.

Climate change is a threat to mining and other industries, especially those involving water supply and management by inducing or amplifying some climatic parameters such as changes in precipitation regimes and temperature extremes. Using the latest NASA NEX-GDDP-CMIP6 datasets, this study quantifies the level of climate change that may affect the development of two mine sites (Site1 and Site2) in northeast Kazakhstan. The study analyses the daily precipitation and maximum and minimum temperature a of a number of global circulation models (GCM) over three future time periods, 2040s, 2060s and 2080s, under two shared socioeconomic pathway (SSP) scenarios, SSP245 and SSP585, against the baseline period 1981- 2014. The analyses revealed that: (1) Both maximum and minimum temperature will increase under both SSP in those time periods, with the rate of change for minimum temperature being higher than maximum temperature. (2) The mean annual precipitation will increase by an average rate of 7% and 10.5% in 2040s for SSP245 and 17.5% and 7.5% for SSP585 in 2080s at Site1 and Site2, respectively. It is also observed that summer months will experience drier condition whilst all other months will increase in precipitation. (3) The values of 24-hour precipitation with 10-year return period will also increase under both SSP scenarios and future time periods for most of the studied GCM and at both mine sites. These predicted changes should be considered as design criteria adjustments for project water supply and water management structures.

Pipe leakage is an inevitable phenomenon in water distribution networks (WDNs), leading to energy waste and economic damage. Leakage events can be reflected quickly by pressure values, and the deployment of pressure sensors is significant for minimizing the leakage ratio of WDNs. Concerning the restriction of realistic factors, including project budgets, available sensor installation locations, and sensor fault uncertainties, a practical methodology is proposed in this paper to optimize pressure sensor deployment for leak identification in terms of these realistic issues. Two indexes are identified to evaluate the leak identification ability, that is, detection coverage rate (DCR) and total detection sensitivity (TDS), and the principle is to determine priority to ensure an optimal DCR and retain the largest TDS with an identical DCR. Leakage events are generated by a model simulation and the essential sensors for maintaining the DCR are obtained by subtraction. In the event of a surplus budget, and if we suppose the partial sensors have failed, then we can determine the supplementary sensors that can best complement the lost leak identification ability. Moreover, a typical WDN Net3 is employed to show the specific progress, and the result shows that the methodology is largely appropriate for real projects.

The Umbulan Water Supply Project is categorized by the Shipping Infrastructure Acceleration Committee in the list of Accelerated National Strategic Projects through Presidential Regulation Number 3 of 2016 concerning the Acceleration of the Implementation of National Strategic Projects, targeted to operate in mid-2019. This is what will be the focus of the stakeholders of the Umbulan Water Supply Project. This study was to identifying and analyzing networks among stakeholders. Method: This study used a qualitative approach with exploratory methods combined with meta-analysis identification design Identification of stakeholder mapping in the context of early detection of stakeholder involvement in the implementation of the Umbulan Water Supply Project at various levels starting from the National, Provincial (East Java), District/City (Pasuruan, Sidoarjo, Surabaya, to Gresik), Sub-District (Winongan, Gondang Wetan, and Pohtjentrek). The conclusion of this study was based on in-depth interviews and focus group discussions in describing the determination of stakeholders which were divided into two, namely primary stakeholder and secondary stakeholder, and outline the result of the indicators analysis on the stakeholder network of Umbulan Water Supply Project.

Control And Data Acquisition (SCADA) systems currently monitor and collect a huge among of data from all kind of processes. In practice, due to sensor failures or to communication errors, in the long-time running, some data may be lost. When it happens, given the nature of these failures, information is lost in bursts, that is, sets of consecutive samples, which besides can be very long. Data completion is a critical step, which must be done with the utmost rigour in order to not propagate errors in the rest of the processing chain stages. Some Big Data techniques do not work if the data series are incomplete, due to the loss of some data. When this occurs it is necessary to fill out the gaps of the historical data with a reliable data completion method. This paper presents an ad-hoc method to replenish the data lost by a SCADA system in case of long bursts. The data correspond to levels of drinking water tanks of a Water Network company that present patterns on a daily and a weekly scale. A method based on tensors is used to take advantage of the data structure. A specially designed \textit{tensorization} is employed to deal with bursts of missed data, applying a twice tensor decomposition and a signal continuity correction. Statistical tests are realized, which consist of apply the data reconstruction algorithms, by deliberately removing bursts of data in verified historical database servers, to be able to evaluate the real effectiveness of the tested methods. For this application, the presented approach outperforms the other techniques found in the literature.

Fisheries in Cambodia play an important role in supporting household food security and livelihoods throughout the country. Inland fisheries production is largely dependent on numerous ecosystem services, particularly the flood waters of the Tonle Sap Lake basin, which has been degraded from increased fishing pressure because of population growth and a rising demand for fish. To address the dual problem of food insecurity and overfishing, an integrated food security and climate change program involved the promotion of small-scale aquaculture through semi-intensive pond management. The objective of this study is to examine perceptions of small-scale aquaculture by participants in this program in order to assess the potential for aquaculture to contribute to household food security and conservation of the Tonle Sap Lake ecosystem. Focus group discussions and a household survey were conducted among current and previous fish farmers. Results demonstrate that most farmers continue to practice small-scale aquaculture as a means to supplement household food availability and income. Numerous barriers to adoption of small-scale aquaculture were identified, including access to water, prices of commercial fish feed, selling price of fish in markets, and concerns about profitability. Seasonal water scarcity is the most prominent challenge in promoting aquaculture technologies, so aquaculture development should be expanded in areas where there are abundant supplies of water, or where use of water storage techniques are feasible. Aquaculture technology appears to have the potential to contribute to food security, nutrition, and household income, and the expansion of the practice of small-scale aquaculture has the potential to reduce fishing pressure on the wild fisheries of the Tonle Sap Lake.

This study was carried out at Kita-mura near Bibai located in central Hokkaido, Japan, with the intention of investigating the effects of different agronomical managements on CH4 emissions from paddy fields on mineral soil over peat under farmers’ actual management conditions in the snowy temperate region. Four fields were studied, including two fields with twice drainage (D1-M and D2-M) and also a single-drainage field (D3-S) under single-cropping yr-1 and a paddy-fallow-paddy crop rotation as their systems. The other field was under single cropping yr-1 with continuous flooding (CF-R) in the pattern of soybean (upland crop)-fallow-paddy. The mineral-soil thickness of these soil-dressed peatland fields varied from 20 to 47 cm. The amount of crop residues leftover in the fields ranged from 277 to 751 g dry matter m−2. Total CH4 emissions ranged from 25.3 to 116 g CH4-C m−2 per growing season. There was a significant relationship between crop-residue carbon (C) and total CH4 emissions during the rice-growing season. This study, therefore, CH4 fluxes from paddy soils in that there was a strong interaction between readily available C source for methanogens and anaerobic conditions created by water management. Despite the differences in water regime and soil type, the average values of straw’s efficiency on CH4 production in this study were significantly higher than those of southern Japan and statistically identical with central Hokkaido. Our results suggest that the environmental conditions of central Hokkaido in association with crop-residue management had a significant influence on CH4 emission from paddy fields on mineral soil over peat. Rotation soybean (upland)-to-paddy followed by drainage twice practices also largely reduces CH4 emission. However, mineral-soil dressing on peat could have a significant impact to suppress CH4 emission from beneath the peat reservoir.

A four stage semi-pilot scale RFR reactor with ceramic disks as support for TiO₂ modified with silver particles was developed for the removal of organic pollutants. The design presented in this article is an adaptation of the rotating biological reactors (RBR) and its coupling with the modified catalyst provides additional advantages to designs where a catalyst in suspension is used. The optimal parameter of rotation was 54 rpm and the submerged surface of the disks offer a total contact area of 387 M². The modified solid showed a decrease in the value of its bandgap compared to commercial titanium. The system has a semi-automatic operation with a maximum reaction time of 50 h. Photo-activity tests show high conversion rates at low concentrations. The results conform to the Langmuir heterogeneous catalysis model.

Evaluating the performance of water indices and mapping the spatial distribution of water-related ecosystems are important for monitoring surface water resources. This is particularly the case for Ethiopia since there is limited information available on water resources development over time despite its relevance for the people and ecosystems. To address this problem, this paper evaluates the performance of seven water indices for country-scale surface water detection based on high spatial and multi-temporal resolution Sentinel-2 data, processed using the Google Earth Engine cloud computing system. Results show that the water index (WI) and automatic water extraction index with shadow (AWEIsh) are the most accurate ones to extract surface water. Comparisons are based on qualitative visual inspections and quantitative accuracy indicators. For the latter, WI and AWEIsh obtained kappa coefficients of 0.96 and 0.95, respectively, and an overall accuracy of 0.98 each. Both indices accounted for similar spatial coverages of surface waters with 82,650 km2 (WI) and 86,530 km2 (AWEIsh) for the whole of Ethiopia.

Permeable pavements have been the subject of numerous studies in recent decades. The possibility of dissipating stormwater more smoothly and generating numerous benefits to the environment and users makes the use of permeable pavements an excellent possibility of integration into sustainable and resilient water management systems in cities. In Brazil, numerous studies on the quantity and quality of infiltrated water, permeability of the coating, clogging, environmental burden, feasibility, among other characteristics, have been researched. Within this theme, the Federal University of Santa Catarina (UFSC) has contributed with ten papers in the research of permeable pavements in the last six years, which address various topics about the effectiveness and applicability of permeable pavements. This paper reviews the studies conducted at UFSC on permeable pavements and discusses the different results within the main issues found. In general, the selected documents addressed seven themes in the studies: potential for potable water savings, clogging, quantity and quality of the water infiltrated into the pavement, Life Cycle Assessment (LCA) and its variants, and hydraulic and structural design details. More specifically, many selected papers assess the potential use of stormwater harvested through permeable pavements in non-potable uses of buildings. The possibility of aligning the benefits of green infrastructure with the rational use of water expands the advantages of the system and can help prevent future water scarcity, as well as reduce the environmental impacts of paving.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

With the development of the city, a large number of water networks in the built-up areas of Bangkok have been filled and hardened, resulting in poor urban flooding and aggravating flooding, causing loss of life and property of citizens. In this paper, on the basis of combing the current water networks and open space potential flood storage points in the built-up areas of Bangkok, the complex network diagram of the water system in the built-up areas of Bangkok is constructed by combining the theory of complex networks and analyzing the attribute parameters of the network and the characteristic parameters of the open space storage nodes and water system paths, and finding that the water system network in the built-up area of Bangkok has complex network characteristics such as robustness, clustering and hierarchy. By exploring the key storage points and water system connection paths, the researchers initially constructed a flood safety pattern in the built-up area of Bangkok with 145 key nodes and 127 river paths as the backbone, and conceptualized the development study of the flood safety pattern in both horizontal and vertical directions. The urban flood safety pattern based on complex network theory proposed in this paper provides a case reference and methodological ideas to scientifically solve the game conflict between the demand for construction land for urban development and the construction area of urban open space storage points and water storage network under the increasingly severe flooding situation.

Well placement optimization in a given geological setting for a fractured geothermal reservoir is a prerequisite for enhanced geothermal operations. High computational cost associated in the framework of fully coupled thermo-hydraulic-mechanical (THM) processes in a fractured reservoir simulation, makes the well positioning as a missing point in developing a field scale investigation. Here, in this study, we shed light on this topic through examining different injection-production well (doublet) position in a given real fracture network. Water and CO2 are used as working fluids for geothermal operations and importance of well positions are examined using coupled THM numerical simulations for both the fluids. Results of this study are examined through the thermal breakthrough time, mass flux and the energy extraction potential to assess the impact of well position in a two-dimensional reservoir framework. Almost ten times of the difference between the final amount of heat extraction is observed for different well position but with the same well spacing and geological characteristics. Furthermore, stress field is be a strong function of well position that is important with respect to the possibility of unwanted stress development. As part of the MEET project, this study recommends to perform similar well placement optimization study for each fracture set in a fully coupled THM manner before a field well drilling.

Flood events are becoming more severe, causing significant problems to human communities, including physical, psychological, and material damage. For both flood forecasting in emergency response situations and flood mapping, georeferencing and data curation are paramount in the context of prevention or preparedness. Hence, data display, data management, and articulation with numerical simulation results must occur on GIS platforms. Our research is motivated by recent advances in Web and GIS technologies, social sensing and high-performance computing, and an envisaged wider availability of remote sensing data. This paper presents and discusses an innovative Web GIS platform named "RiverCure Portal" or "RCP" for short. This platform combines observations and hydrodynamic modelling tools to support various stages of the flood risk management cycle, including operational response, emergency preparedness, and risk assessment. RCP is a multi-organisation, multi-context digital platform with flexible configuration features to define and support multiple sensor types and modelling options, satisfying the various needs of different organisations and stakeholders. In addition, this paper discusses the RiverCure Approach, which encompasses the following tasks directly supported by the RCP platform: defining the context and involved geometries, associating sensors to the context, pre-processing and generating the context mesh, defining the simulation event, running the simulation event, and analysing the results from the simulation event. Thus, the RCP streamlines and simplifies data analysis and simulation procedures to meet decision-makers' needs. The novelties discussed in this paper include the design and discussion of a Web GIS platform that allows (i) to manage flood data and results of simulations at several contextual levels by different stakeholders such as domain experts, decision-makers, researchers, or students; (ii) to process and curate sensed data obtained from physical and social sensors; and (iii) update the state and values of the parameters of simulation tools through continuous data assimilation techniques for forecasting purposes. Finally, this paper supports the explanation and discussion with a running example, "Águeda 2016 flood" event, which dataset is publicly available for further study and experimentation.

In recent years, many studies have highlighted the consistent finding of amoxicillin in waters destined for wastewater treatment plants, in addition to superficial waters of rivers and lakes in both Europe and North America. In this paper, the amoxicillin degradation pathway was investigated by simulating the chlorination process normally used in a wastewater treatment plant to reduce similar emerging pollutants at three different pH values. The structures of 16 isolated degradation byproducts (DPs), one of which was isolated for the first time, were separated on a C-18 column via a gradient HPLC method. Then, combining mass spectrometry (MALDI-MS/TOF) and nuclear magnetic resonance, we compared commercial standards and justified a proposed formation mechanism beginning from the parent drug. Microbial growth inhibition bioassays with Escherichia coli, Klebsiella pneumoniae, and Staphylococcus aureus were performed to determine the potential loss of antibacterial activity in isolated degradation byproducts. An increase of antibacterial activity in the DPs was observed compared to the parent compound.

Safety of source water streams is an urgent environmental issue, while protections in monsoon controlled subtropical regions face difficulties because of the lack of small scaled observation and analysis in small source water catchments. Basing on continuous weekly water quality data (2014-2017) in Pingqiao River Catchment, the annual average values of TN, NO₃, NH₄ and TP are 3.36, 1.64, 0.28 and 0.02 (mg/L) respectively. During dry, normal and wet seasons, the variability of parameters is over 35%, which indicates an obvious seasonality. Multiple methods are combined in order to assess the water quality and find the driving factors during dry, normal and wet seasons. This study suggests precipitation and fertilization are the mainly seasonal factors, which can make water quality better in wet season than dry season due to the dilution effect. The mechanism between seasonality and compound of nutrients can also be traced by log(TN:TP), and log(NO₃:NH₄). Among six main land use types (forest, tea plantation, cropland (paddy), urban, bare soil and water), the former three ones are influential mostly during dry and wet season. Tea plantation has the largest nutrients discharge amount per area, which is similar to cropland in dry season. By contrary, forest has the double power in reducing nitrogen release in wet and normal seasons. When transformed into paddies, croplands can lower the phosphorus concentration. Conclusions of this study can be used in southeastern China and similar regions on source water protection and agricultural plans.

Degraded soils causing from natural and human affects are universal in arid and semi-arid regions all over the world. Bentonite and humic acid (BHA) are increasingly being tested to remediate these degraded lands with potential benefits on crop production and soil health. The objective of this paper was to determine the residual effects four to five years after a one-time BHA application at six rates on (i) dynamic changes in soil properties, and (ii) oat crop productivity parameters, in a dryland farming ecosystem. With increasing rates of one-time BHA application, soil profile water storage displayed a piecewise linear increase plus plateau, whereas soil electrical conductivity, pH and bulk density were all reduced significantly (P < 0.05) in the 0-20 cm and 20-60 cm layers. The improved soil environments gave rise to an increased activity of soil enzymes urease, invertase and catalase that respectively reached the peak values of 97%, 37% and 32% at the rates of 21 to 24 Mg BHA ha-1. These conversely boosted soil nutrient turnover, leading to a 40% higher soil available P. Compared with the control treatment, application of BHA at the estimated optimum rate (roughly 24 Mg ha-1) increased grain yield by 20%, protein yield by 62%, water use efficiency by 41%, and partial factor productivity of N by 20%. Results of this study showed for the first time that a one-time BHA application would be a new and effective strategy to combat land degradation, drought, and promote a sustainable soil micro-ecological environment in dryland agroecosystem under a varying climate scenario.

Pistol shrimps generate cavitation bubbles. Cavitation impacts due to bubble collapses are harmful phenomena, as they cause severe damage to hydraulic machineries, such as pumps and valves. However, cavitation impacts can be utilized for mechanical surface treatment to improve the fatigue strength of metallic materials, which is called “cavitation peening”. Through conventional cavitation peening, a cavitation is generated by a submerged water jet, i.e., a cavitating jet or a pulsed laser. The fatigue strength of magnesium alloy when treated by the pulsed laser is larger than that of the jet. In order to drastically increase the processing efficiency of cavitation peening, the mechanism of pistol shrimp (specifically when used to create a cavitation bubble), i.e., alpheus randalli, was quantitatively investigated. It was found that a pulsed water jet generates a cavitation bubble when a shrimp snaps its claws. Furthermore, two types of cavitation generators were developed, namely, one that uses a pulsed laser and one that uses a piezo actuator, and this was achieved by mimicing a pistol shrimp.

Manufactured sand and natural sand have great differences in terms of physical properties, chemical composition, and so on. In the mix ratio design of manufactured sand concrete, the traditional common concrete ratio cannot be used. The water-cement ratio playing a crucial role in the mix ratio design. The optimum water-cement ratio can not only improve concrete performance, it can also reduce cement consumption and costs. The present study examines the working performance indicators and mechanical performance indicators of manufactured sand concrete using Fujian granite with three strength grades (C35, C40 and C50) at different water-cement ratios. The impact of water-cement ratio on the operational and mechanical performance of manufactured sand concrete with different strength grades is analyzed and summarized. Revised sentence: The findings suggest that the workability of Fujian granite concrete is directly influenced by the water-cement ratio. Additionally, the water-cement ratio indirectly affects the mechanical properties of manufactured sand concrete. Finally, when changing the water-cement ratio, cube compressive strength, splitting tensile strength and bending strength exhibit similar trends. The optimal water-cement ratio for C35 concrete is determined to be 0.39, considering the workability and mechanical properties of Fujian granite manufactured sand concrete. Similarly, the optimal water-cement ratio for C40 concrete is 0.34, while for C50 concrete it is 0.32.

For efficient electrode development in an electrolysis system, Fe₂O₃, MnO, and heterojunction Fe₂O₃-MnO materials were synthesized via a simple sol-gel method. These particles were coated on a Ni-foam electrode, and the resulting material was used as an electrode to be used during an oxygen evolution reaction (OER). A 1000-cycle OER test in a KOH alkaline electrolyte indicated that the heterojunction Fe₂O₃-MnO/NF electrode exhibited the most stable and highest OER activity: it exhibited a low overvoltage (n) of 370 mV and a small Tafel slope of 66 mV/dec. X-ray photoelectron spectroscopy indicated that the excellent redox performance contributed to the synergy of Mn and Fe, which enhanced the OER performance of the Fe₂O₃-MnO/NF electrode. Furthermore, the effective redox reaction of Mn and Fe indicated that the structure maintained stability even under 1000 repeated OER cycles.

Here are analysed data taken in two hydrocarbon fields ("A" and "B"), located in the western part of Sava Depression (North Croatia). They are in the secondary phase of production. The selected reservoirs "L" (in the “A” Field) and "K" (“B”) are of the Lower Pontian (Upper Miocene) age and belong to Kloštar-Ivanić Formation. Due to strong tectonics, there are numerous tectonic block, relatively rarely sampled with well and laboratory tests. Here are selected two variables for interpolation - reservoirs permeabilities and the injected volumes of field water. The following interpolation methods are described, compared and applied: Nearest Neighbourhood, Natural Neighbour (the first time in the Sava Depression) and Inverse Distance Weighting. The last one has been proven as the most appropriate for datasets with size lower than 20 points.

This article aims at investigating the complex relationship between the local population and its natural and urban environment. The study of area which, is previously dominated by cereal cultivation, facing profitability challenges due to climate change, water scarcity Rapid urban expansion and overexploitation of aquifers, influenced by changes in agricultural practices, are disrupting the local ecosystem. The study relies on three interconnected indicators: population growth, climate change effects on agriculture, and the NDVI (Normalized Difference Vegetation Index) reveal the impact of these factors on agricultural practices. Google Earth Engine was employed to determine urbanization and greenness indices using scripts. Key findings include a shift towards intensive and protected agriculture, driven by individual and collective choices of official and unofficial actors, deviating from government directives. Additionally, the study highlights the unsustainability of this new agricultural direction, as the available water re-sources cannot meet the demands, potentially leading to recurrent agricultural shortages. The study underscores the importance of incorporating agricultural production into future urban planning and development programs to maintain a renewed balance between built environ-ments and agriculture on the outskirts of cities.

Reductions in water availability and increasing rainfall variability are generating a narrative of growing competition for water in the Mediterranean basin. In this article, we explore the distribution and importance of water resources in the Muga River Basin (Catalonia, Spain) based on key stakeholders’ perceptions. We performed a sociocultural evaluation of the main water ecosystem services in the region through stakeholder interviews and participatory mapping. The basin was generally perceived as a hotspot of ecosystem services, but we detected varying opinions and considerable differences in the perceptions of importance and spatial distribution of water ecosystem services. These discrepancies were linked to the varying levels of stakeholders’ dependence on water. Our findings are important for contributing to correct water planning and management in the river basin, which is a complex water social system marked by conflicts between different stakeholder groups vying for the same resource. This complex situation requires bottom-up strategies to create transparent, participatory decision-making models.

The fundamental mechanism underlying negative-ion catalysis involves bond-strength breaking in the transition state (TS). Doubly-charged atomic/molecular anions are proposed as novel dynamic tunable catalysts and demonstrated in water oxidation to peroxide. Density Functional Theory TS calculations have found tunable energy activation barrier reduction ranging from 0.030 eV to 2.070eV, with Si²ˉ, Pu²ˉ, Pa²ˉ and Sn²ˉ the best catalysts; the radioactive elements usher in new application opportunities. C₆₀²ˉ reduces significantly the standard C₆₀ˉ TS energy barrier while graphene increases it, behaving like cationic systems. Rank-ordered catalysts according to their reaction barrier reduction efficiency, variation across charge states and systems reveal their tunable and wide applications, ranging from water purification to biocompatible anti-viral and anti-bacterial sanitation systems.

Energy demand has exponentially increased with the increase in the world population and ur-banization. Renewable energy is clean, renewable, and environmentally friendly. Hydrogen production through Proton Exchange Membrane (PEM) electrolyzer is an efficient way to produce renewable energy. The efficiency and energy consumption of the PEM electrolyzer depends on the feed water quality. In this report, we study the effect of pH, TDS, and conductivity on hydrogen production as well as energy consumption during the process. pH values (3, 7, 9), TDS values (300ppm, 600ppm, 900ppm), and conductivity values (30mS/cm, 70mS/cm, 100mS/cm) were studied to understand and optimize the hydrogen production using PEM electrolyzer. The in-vestigations showed that hydrogen production is significantly affected by pH, total dissolved solids, and conductivity, and the best levels of each variable were identified by extensive testing. The findings show both the scientific significance of proton exchange electrolysis in meeting the growing energy demands of society as well as the importance of knowing the influence that di-verse conditions have on the creation of hydrogen. Our research, in general, contributes to the expanding body of scientific knowledge on the topic of the effective production of hydrogen and offers useful insights for the continuation of investigation in this field.

Today, the style of light construction materials used in building is one of the most important factors in reducing building's dead load and better performance of the structures in the earthquake. One of the ways to reduce the structure weight is to use lightweight blocks instead of using traditional materials. The main purpose of this research is to compare density, compressive strength and water absorption volume of non-load-bearing lightweight blocks made of natural and artificial lightweight aggregates. Scoria lightweight aggregates of Sanandaj, Ghorveh mine, pumice in Tabriz, Bostanabad mine, and Leca in Leca enterprise have been used to make the samples. Given the importance of the materials used, grading of coarse-grained materials has been conducted based on the standard of 7657 and grading of fine materials have been conducted based on the standard of 302.The experiments' results show that Scoria blocks due to hard texture, and high mechanical resistance of their lightweight aggregates, have had higher compressive strength, and density and lower water absorption volume compared to pumice and Lika lightweight aggregate blocks. Pumice blocks despite having desirable compressive strength and lower density compared to the two other blocks have higher water absorption volume, and do not meet the standard conditions. This same factor causes it faces with less interest. Among these Lika blocks with density of 1151.94 (kg per cubic meter) below 2000 kilograms per cubic meter of Iran density standard of 7782 (28-day compressive strength of 2.57 MPa), higher than 2.5 MPa of Iran compressive strength standard of 7782 (and water absorption volume of 282.92 kg per cubic meter) below 288 kilograms per cubic meter of Iran water absorption volume standard of 7782 (as a non-load-bearing lightweight block) have been diagnosed desirable.

In the field of climate change adaptation, the future matters. Amongst others, river futures justify the way adaptation projects materialize in rivers. In this paper, we challenge the ways in which dominant paradigms and expert claims monopolise the truth concerning policies and designs of river futures, side-lining and delegitimizing alternative river futures. Currently, limited work is done to critically reflect on the power of river futures in the context of climate change adaptation. We conceptualized the power of river futures through river imaginaries: collectively performed and publicly envisioned reproductions of riverine socionatures, mobilized through truth claims of social life and social order. Through the Border Meuse project case study, a climate change adaptation project in a stretch of the river Meuse in the south of the Netherlands and a proclaimed success story of climate adaptation in Dutch water management, we elucidated how three river imaginaries: a modern river imaginary, a market-driven imaginary and an eco-centric river imaginary, merged and materialized as an eco-modern river imaginary. Importantly, not only the river futures merged, also their aligned truth regimes merged. To this end, we argue that George Orwell’s famous quote “Who controls the past, controls the future: who controls the present, controls the past” can be extended to ‘Who controls the future, controls how we see and act in the present, and how we rediscover the past’.

Regeneration is crucial for forest continuity in natural and managed stands. Analyzing intra-annual dynamics improves the understanding between growth and climate, identifying survival thresholds. The objective was to determine microclimate constraints (rainfall, air and soil temperatures) over Nothofagus antarctica regeneration growing at closed, open, and edge forests in Patagonia. We measured stand characteristics (forest structure, understory, soil properties, animal use), microclimate, and daily growth of regeneration using dendrometers (n = 6) during two growing seasons. We found significant differences in the studied variables (e.g. overstory, light, soil, understory, animal use). These changes defined microclimate across overstory gradient (e.g. soil moisture), influencing the daily growth across seasons (lag, exponential, stationary). Rainfall influenced more than temperature. Daily growth in closed forests indicating shrinkage (-0.0082 mm day-1 without rain, and -0.0008 mm day-1 with 0.0-0.2 mm day-1 rainfall), while above 0.2 mm day-1 rainfall, growth always increased. Open forests presented shrinkage during days without rain (-0.0051 mm day-1), showing positive growths according rainfall. Edge forests always presented positive daily growths. The resilience of regeneration under these changed conditions was related with overstory. Main outputs indicated that regeneration was vulnerable during non-rainy days, suggesting the needs of long-term monitoring to develop better silvicultural proposals.

Background: Instrument-assisted soft tissue mobilization (IASTM) is thought to alter fluid dynamics in human soft tissue. The aim of this study was to investigate the influence of IASTM on the thoracolumbar fascia (TLF) on the water content of the lumbar myofascial tissue. Methods: 21 healthy volunteers were treated with IASTM. Before and after the procedure and 5 and 10 minutes later, lumbar bioimpedance was measured by bioimpedance analysis (BIA) and TLF stiffness by indentometry. Tissue temperature was recorded at the measurement time points using an infrared thermometer. Results: Bioimpedance increased significantly from 58.3 to 60.4 Ω (p < 0.001) at 10-minute follow-up after the treatment. Temperature increased significantly from 36.3 to 36.6° Celsius from 5 to 10 minutes after treatment (p = 0.029), while lumbar myofascial stiffness did not change significantly (p = 0.84). Conclusions: After the IASTM intervention, there was a significant increase in bioimpedance, likely due to a decrease in water content in myofascial lumbar tissue. Further studies in a randomized control trial design are needed to extrapolate the results in healthy subjects to a symptomatic population as well and to confirm the reliability of BIA in myofascial tissue.

Many industrial processes, several natural processes involving non-living matter, and all the processes occurring within living organisms take place in solution. This means that the molecules playing active roles in the processes are present within another medium, called solvent. The solute molecules are surrounded by solvent molecules and interact with them. Understanding the nature and strength of these interactions, and the way in which they modify the properties of the solute molecules, is important for a better understanding of the chemical processes occurring in solution, including possible roles of the solvent in those processes. Computational studies can provide a wealth of information on solute-solvent interactions and their effects. Two major models have been developed to this purpose: a model viewing the solvent as a polarizable continuum surrounding the solute molecule, and a model considering a certain number of explicit solvent molecules around a solute molecule. Each of them has its advantages and challenges, and one selects the model that is more suitable for the type of information desired for the specific system under consideration. These studies are important in many areas of chemistry research, from the investigation of the processes occurring within a living organism to drug design and to the design of environmentally benign solvents meant to replace less benign ones in the chemical industry, as envisaged by the green chemistry principles. The paper presents a quick overview of the modelling approaches and an overview of concrete studies, with reference to selected crucial investigation themes.

The shallow water equations are widely applied for the simulation of flow routing in rivers and floodplains, as well as for flood inundation mapping. From a mathematical point of view, they are a hyperbolic system of nonlinear partial differential equations, whose numerical integration is sometimes computationally burdensome. For this reason, the interest of many researchers has been focused on the study of simplified forms of the original set of equations, which requires less computational effort. One of the most commonly applied simplifications consists in neglecting the inertial terms, which changes the hyperbolic model to a parabolic one. The effects of such a choice on the outputs of the simulations of flooding events are controversial and an important topic of debate. In the present paper, two numerical models, recently proposed for the solution of the complete and zero-inertia forms of the shallow waters equations, are applied to several unsteady flow routing scenarios. We simulate synthetic and laboratory studies, starting from very simple geometries and moving towards complex topographies. Analyzing the role of the terms in the momentum equations, we try to understand the effect, on the computed results, of neglecting the inertial terms in the zero-inertia formulation. We analyze the computational costs.

Organic farming has positive, impact on environment, soil health, and healthy food quality. Worldwide demand for organic foods is increasing by leaps and bounds in recent years. The present investigation was undertaken during 2014 to 2018 to evaluate the effect of cowpea (Vigna unguiculata) co-culture with maize (Zea mays L.) on productivity enhancement over prevailing maize-fallow system, and to assess the feasibility of inclusion of short duration winter crops after maize with appropriate residue management practices on productivity and soil health. The experiment comprised of six cropping systems in main plot and three soil moisture conservation (SMC) measures options in sub plot. Results indicated that the inclusion of second crop in place of fallow and cowpea co-culture with maize increased average maize grain yield by 6.2 to 23.5% as compared to that of maize-fallow (MF). Use of maize stover mulch (MSM) + weed biomass mulch (WBM) increases maize grain yield by 19.1 and 6.5% over those of MSM and no mulch (NM), respectively. Various soil moisture conservation (SMC) measures had significant (p=0.05) effect on crop yields and water productivity. Double cropping system had significantly (p=0.05) higher amount of soil available NPK, soil organic carbon (SOC), microbial biomass carbon (MBC) and dehydrogenase activity (DHA) at 0-15 cm and at 15-30 cm depth than those under MF. The SWC measures of MSM+WBM had significantly higher available N, SOC, and MBC by 5.5, 4.8 and 8.1% than those under NM, respectively. Correspondingly, soils under MSM and MSM+WBM had 2.24 and 2.99% lower bulk density (ρb) in 0-15 cm and 2.21 and 2.94% lower ρb in 15-30 cm than that of NM. The energy use efficiency (EUE) was significantly higher under MCV (7.90%) over rest of the cropping sequences. MSM+WBM and MSM recorded 25.1 and 16.6% higher net energy over NM, respectively. The net return (INR 159.99×103/ha) and B:C ratio (2.86) were significantly higher with MCV system followed by MCR cropping sequence. MSM+WBM had significantly higher net return (INR 109.44×103/h), B:C ratio (2.46) over those under MSM (INR 97.6×103/h) and NM (INR 78.61×103/h). Overall the cowpea co-culture with maize and inclusion of short cycle winter crops along with MSM+WBM in maize-based cropping systems was found productive in terms of crop and water, profitable, energy efficient and sustained the soil health.

This paper presents the results of a comparison of the seasonal dynamics of carbon dioxide content in the atmosphere and the phenological phases of various water bodies located in the boreal and subarctic zones for 2012–2020. Six large freshwater areas were selected as research objects: Lake Baikal, Lake Ladoga, Gulf of Ob, Lake Huron, Great Bear Lake and Great Slave Lake. In addition, four areas of wetlands in Western Siberia were studied. The CO2 concentration in the air column over water bodies was obtained from CAMS global greenhouse gas reanalysis data. These data represent three-dimensional fields of aerosols and chemical components in the atmosphere, with complete coverage of the globe. The phenological phases of the water bodies were determined using data from the MIRAS microwave radiometer of the SMOS satellite. The comparison and analysis performed showed that the concentration of CO2 in the atmosphere over the studied water bodies has a seasonal cyclical nature. The minimum concentration corresponds to the summer period due to strong photosynthesis of phytoplankton and swamp vegetation, which results in the absorption of carbon dioxide. The maximum CO2 concentration over the water bodies corresponds to the end of the winter – the beginning of the spring period, when photosynthesis processes are minimal. During this period, CO2 is being accumulated in water bodies and subsequently emitted. In freezing lakes located in the boreal zone, in addition to a stable spring maximum of CO2, a strong short-term release of carbon dioxide is sometimes observed, also corresponding to the stage of destruction of the ice cover. It is associated with the release of CO2 accumulated over the winter period, which was “sealed” in the ice and in the water column under the ice. The absence of such a release in the waters of the subarctic zone is explained by the lower biological productivity of these reservoirs compared to the waters of the boreal zone.

The extracts from the aerial parts of Helianthus salicifolius A. Dietr and Helianthus tuberosus L. collected in June were obtained using carbon dioxide supercritical fluid extraction with water as co-solvent. The antimicrobial activity in vitro of these extracts were determined against the reference species of Gram-positive and Gram-negative bacteria as well as fungi, representing by the yeast species of Candida spp. The following parameters were estimated: minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) or minimum fungicidal concentration (MFC). Both extracts were found to possess antimicrobial activity with MIC = 0.62-5 mg mL-1 for bacteria and MIC = 5-10 mg mL-1 for yeasts, showing bactericidal (MBC/MIC = 2-4) or fungicidal effect (MFC/MIC = 1-2 ). The highest activity was observed against S. aureus ATCC 29213 (MIC = 0.62 mg mL-1 for H. salicifolius extract; MIC = 2.5 mg mL-1 for H. tuberosus extract). Bactericidal effect of both extracts against S. aureus ATCC 29213 was confirmed by time-kill assay. Higher antioxidant activity was found for H. tuberosus extract (EC50 = 0.332 mg mL-1) as compared to that of H. salicifolius (EC50 = 0.609 mg mL-1). The total polyphenol content (TPC) expressed as gallic acid equivalents (GAE) was 13.75 ± 0.50 mg GAE (g of H. salicifolius extract)-1 and 33.06 ± 0.80 mg GAE (g of H. tuberosus extract)-1. There was a correlation between the antioxidant potential of both extracts and TPC but not between antistaphylococcal activity and TPC. The obtained data suggest potential application of these extracts as the natural preparations with the biocidal activity, including those with antistaphylococcal activity. Besides, both extracts may be regarded as potential natural conservants in cosmetics as well as natural preservatives in food.

With the rapid development of urbanization, the chemical evolution of groundwater is significantly affected by human activities. However, the driving mechanisms of groundwater chemical evolution at different stages of urbanization remain unclear, severely impacting the implementation of groundwater protection. This study investigated the driving mechanisms of groundwater chemical evolution based on the long-term series (from 1985 to 2015) of hydrochemical data from 19 groundwater monitoring sites in rapidly urbanizing areas (Shijiazhuang, Hebei Province, China). The results show that the concentrations of various chemical components in groundwater gradually increase with the acceleration of urbanization process, especially NO3-, which has increased from 13.7 mg/L in the primary stage of urbanization (PSU) to 65.1mg/L in the advanced stage of urbanization (ASU), exceeding the WHO drinking water standard (50mg/L), indicating that the groundwater chemistry has been significantly affected by human activities. It is interesting to find that the main hydrochemical types have changed from HCO3•SO4-Ca•Mg type water in the PSU to SO4•HCO3-Ca•Mg type water in the ASU. It is worth noting that there were obvious differences in driving factors of groundwater chemical evolution at different urbanization stages. In the PSU, the driving factors of groundwater chemical evolution were carbonate and rock salt dissolution, cation exchange, and industrial activities. However, in the intermediate stage and advanced stage, the driving factors of groundwater chemical evolution were changed to carbonate and gypsum dissolution, groundwater over-exploitation, agricultural fertilization, and domestic sewage. Based on the above conclusions, it is suggested that future groundwater management should control the amount of agricultural fertilizers, apply scientific fertilization, and prohibit the discharge of various types of non-compliant sewage, while strengthening the supervision of groundwater extraction to reduce the impact of urbanization development on the groundwater chemical evolution process.