Traditionally, neutron scattering is an essential method for the analysis of spin structures and spin excitations in bulk materials. Over the last 30 years, polarized neutron scattering in terms of reflectometry has also contributed largely to the analysis of magnetic thin films and magnetic multilayers. More recently it has been shown that polarized neutron reflectivity is, in addition, a suitable tool for the study of thin films laterally patterned with magnetic stripes or islands. We provide a brief overview of the fundamental properties of polarized neutron reflectivity, considering different domain states, domain fluctuations, and different domain sizes with respect to the neutron coherence volume. The discussion is exemplified by a set of simulated reflectivities assuming either complete polarization and polarization analysis, or a reduced form of polarized neutron reflectivity without polarization analysis. Furthermore, we emphasize the importance of the neutron coherence volume for the interpretation of specular and off-specular intensity maps, in particular when studying laterally non-homogeneous magnetic films. Finally, experimental results, fits, and simulations are shown for specular and off-specular scattering from a magnetic film that has been lithographically patterned into a periodic stripe array. These experiments demonstrate the different and mutually complementary information that can be gained when orienting the stripe array parallel or perpendicular to the scattering plane.

This paper aims to review the challenges, toxicity, and routes of synthesis and usage of silver nanoparticles in different applications but also highlighting their sustainability from both medical and environmental issues. Regarding their toxicity, it is known that silver nanoparticles can destroy over 650 microorganisms comparing with antibiotics. Supplementary, will be presented in a comparative manner some conventional synthesis routes (physical and chemical methods) and green synthesis routes using plant extracts. The approach using plant extracts have various advantages comparing with physical, chemical and microbial synthesis methods because there is no need to use chemicals, wasteful purifications and high energy requirements. The paper presents an overview on “green nanotechnology” focused on using either biological micro-organisms or plant extracts as an alternative to the classical chemical and physical methods. An important issue discussed in the paper is an overview of the synthesis routes of silver nanoparticles, some expected applications of silver based active agents and their toxicity and challenges that must be overcome. Also, it needs to focus our attention on the dismissal of silver nanoparticles into the environment and especially in water systems, fact which suggests that this issue must be fully understood and applied the law.

The development of innovative materials is one of the most important focuses of research in heritage conservation. Eligible materials can not only protect the physical and chemical integrity of artworks, but also preserve their artistic and aesthetic features. Recently, as one of the hot research topics in materials science, biomimetic superhydrophobic materials have gradually attracted the attention of conservation scientists due to their unique properties. In fact, ultra-repellent materials are particularly suitable for hydrophobization treatments on outdoor artworks. Owing to their excellent hydrophobicity, superhydrophobic materials can effectively prevent the absorption, penetration of liquid water as well as the condensation of water vapor, thus greatly relieving water-induced decay phenomena. Moreover, in presence of liquid water, the superhydrophobic surfaces equipped with self-cleaning property can clean the dirt, dust deposited spontaneously, thereby restoring the artistic features simultaneously. In the present paper, besides the basic principles of wetting on solid surfaces, materials and methods reported for preparing bioinspired ultra-repellent materials, the recently proposed materials for art conservation are also introduced and critically reviewed. Lastly, the current status and the problems encountered in practical application are also pointed out, and the focus of future research is prospected as well.

In order to develop waterborne silicate anticorrosive coatings to replace solvent-based anticorrosive coatings used widely in ship’s industry, epoxy modified silicate emulsions were synthesized with different content of epoxy resin, then aqueous silicate zinc-rich coatings were prepared with synthesized silicate emulsion, triethylamine and zinc powder. The influence of the content of epoxy on the properties and chemical structure of modified emulsion, mechanical properties of silicate coatings, and the corrosion behavior of silicate zinc-rich coatings in 3.5% NaCl solution were investigated. The coating samples on steel were measured by immersion test, Tafel polarization test and electrochemical impedance spectroscopy (EIS) test with different immersion time. The results showed that epoxy modified silicate emulsions were successfully synthesized. With the increase of epoxy content, the viscosity and the solid content of modified emulsion increases, the impact resistance of the silicate coating raises, the pencil hardness decreases, but the adhesion is not affected. Epoxy modification can reduce to s certain extent the corrosion driving force of zinc rich coating and increase the impedance of the zinc-rich coating decreases with the increase of immersion time in 3.5% NaCl solution. With the increase of the epoxy content, the resistance value of the zinc-rich coating increases, indicating the ability of the coating to resist corrosive media is enhanced.

Graphene-oxide (G) was prepared by the Hummers’ method. A G-COOH layer was synthesised using chloroacetic acid and G. To fabricate carboxylated graphene-RuO2 (G-COORu) nano¬¬-composites, RuO2 nano particles were grown on graphene layers using a one-step thermal method, -COOH(G-COOH), and RuCl3. All materials were characterised using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, 13C-nuclear magnetic resonance as well as X-ray photoelectron, Fourier-transform infrared spectroscopy, and Raman. The electrochemical characteristics of the G-COORu supercapacitors were analysed using electrochemical impedance spectroscopy, cyclic voltammetry, constant current charge–discharge tests, and Nyquist impedance plots. The supercapacitors exhibit a specific capacitance of ~125 F g-1 at 100 mA cm-2 within the potential range of 0–1.0 V. The method used here provides a simple approach for the deposition of RuO2 nano particles on graphene layers and can be widened to the fabrication of other classes of hybrids based on G layers for specific technical applications.

Starting from December 2019, coronavirus disease 2019 (COVID-19) has emerged as a once-in-a-century pandemic with deadly consequences, which urgently calls for new treatments, cures and supporting apparatuses. Remdesivir was reported by World Health Organization (WHO) as the most promising drug currently available for the treatment of COVID-19. Here, we use molecular dynamics simulations and free energy perturbation methods to study the inhibition mechanism of remdesivir to its target SARS-CoV-2 virus RNA-dependent RNA polymerase (RdRp). In the absence of a crystal structure of the SARS-CoV-2 RdRp, we first construct the homology model of this polymerase based on a previously available structure of SARS-CoV NSP12 RdRp (with a sequence identify of 95.8%). We then build the putative binding mode by aligning the remdesivir + RdRp complex to the ATP bound poliovirus RdRp. The putative binding structure is further optimized with molecular dynamics simulations and demonstrated to be stable, indicating a reasonable binding mode for remdesivir. The relative binding free energy of remdesivir is calculated to be -8.28 ± 0.65 kcal/mol, much stronger than the natural substrate ATP (-4.14 ± 0.89 kcal/mol) which is needed for the polymerization. The ~800-fold improvement in the K_d from remdesivir over ATP indicates an effective replacement of APT in blocking of the RdRp binding pocket. Key residues D618, S549 and R555 are found to be the contributors to the binding affinity of remdesivir. These findings demonstrate that remdesivir can potentially act as a SARS-CoV-2 RNA-chain terminator, effectively stopping its RNA reproduction, with key residues also identified for future lead optimization and/or drug resistance studies.

Molecular engineering research is the fundamental way and the only way for the development of biomaterials. Based on molecular engineering, the biocompatibility of natural conformation and polymer biomaterials was studied. In this paper, we discuss that natural conformation is the basis of protein biological function, and that the synergistic action of peptide chain and side group is the motive force for protein to construct natural conformation and complete biological function. On the basis of the influence of the adsorption of polymer biomaterials on the natural conformation of proteins, the relationship between biocompatibility of biomaterials and protein conformation is further explained. Studies have shown that bismuth molecular materials can only be applied in the market and have their functionality if they have good biocompatibility. Therefore, the biocompatibility evaluation of new materials has important practical significance.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

With the increasing resistance of bacteria to current antibiotics, novel compounds are urgently needed to treat bacterial infections. Streptozotocin (STZ) is a natural product that has broad-spectrum antibiotic activity, albeit with limited use because of its toxicity to pancreatic β cells. In an attempt to derivatize STZ through structural modification at the C3 position, we performed the synthesis of three novel STZ analogues by making use of our recently developed regioselective oxidation protocol. Keto-STZ (2) shows the highest inhibition of bacterial growth (MIC and viability assays), but is also the most cytotoxic compound. Pre-sensitizing the bacteria with GlcNAc increased the antimicrobial effect, but did not result in complete killing. Interestingly, allo-STZ (3) revealed moderate concentration-dependent antimicrobial activity and no cytotoxicity towards β cells, and deoxy-STZ (4) showed no activity at all.

In many instances paints interlayers delamination is attributed either to environmental or to application reasons. The composition as well as the structure, including morphology are always given for granted. The resin to pigment ratio, the surfactants, the quality of pigments and fillers (dimensions, shape, wettability, reactivity, homogeneity of distribution…) are not clearly required, defined and consequently checked. A fundamental article appeared in 1949 defining PVC and CPVC. In the following, it was quoted several times but not many improvements in the subject were shown: the subject was considered as obvious and unquestionable. We have tested some cases of coating delamination from big steel structures where other causes were either absent or not dominating if paint features were not taken into account. Many features of paint composition and structure were analyzed with both SEM and EDAX and a comparison with a carefully formulated paint was carried out.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

Static (SLS) and dynamic (DLS) light scattering techniques are assessed for their capacity to detect colloidal particles with diameters between d = 0.1 and 0.8 µm at very low concentrations in seawater. The detection limit of the apparatus was determined using model monodisperse spherical polystyrene latex particles with diameters 0.2 µm and 0.5 µm. It is shown that the concentration and size of colloids can be determined down to about 10^-6 g/L. Seawater obtained from different locations in western Europe was characterized using light scattering. It was found that seawater filtered through 0.45 µm pore size membrane filters was within the experimental error the same as that of ultrapure Milli-Q water containing the same amount of sea salt and no colloids could be detected with DLS. When the seawater was filtered through 0.8 µm pore size filters, colloidal particles were detected. The measurements show that the concentration of colloids in the seawater samples is not higher than 10^-6 g/L and that they have an average diameter of about 0.6 µm. We stress that these particles are not necessarily nanoplastics.

In this research, low-fat dried Chinese sausage was formulated with mango peel pectin (MPP) extracted by microwave assisted extraction (MAE) (0%, 5%, 10% and 15% (w/w). The extractable yield of pectin attained from peel of Nam Dok Mai variety was achieved at 13.85% using 700-watt power. The extracted MPP were of high equivalent weight (1,485.78 mg/mol), degree esterification (77.19%) and methoxyl content (19.33%) with the structure of more porosity as compared to that of the conventional method. Spectrum scans by Fourier transform infrared spectrophotometer (FT-IR) advised that the extracted MPP gave the similar wave number profiles as the commercial pectin. Quality attributes of the Chinese sausages were accessed and compared with the control formula (CTRL). At higher concentrations of MPP, the product had positively increased colour intensity. The texture profile of the sausage illustrated that only the hardness value was comparable with the CTRL, while springiness, cohesiveness, gumminess and chewiness were statistically lower (p < 0.05). Furthermore, the sensory evaluation by experienced panellists (n=12) indicated that 5% MPP similarly represented overall acceptability with the CTRL. Consequently, MPP can be effectively applied at low level as fat replacement in Chinese sausage allowing colour improvement and product of healthier option.

In this paper, we present a preliminary study and conceptual idea concerning 3D printing water-sensitive glass by exemplifying with a borosilicate glass with high alkali and alkaline oxide contents using direct ink writing. The investigated material was prepared in the form of a glass frit, which was further ground in order to obtain a fine powder of desired particle size distribution. In a following step, inks were prepared by mixing the fine glass powder with Pluoronic F-127 hydrogel. The acquired pastes were rheologically characterized and printed using a Robocasting device. DSC experiments were performed for base materials and the obtained green bodies. After sintering, SEM and XRD analyses were carried out in order to examine microstructure and the eventual presence of crystalline phase inclusions. Results confirmed that obtained inks exhibit stable rheological properties despite the propensity of glass to undergo hydrolysis and could be adjusted to desirable values for 3D printing. No additional phase was observed, supporting the suitability of the designed technology for the production of water sensitive glass inks. SEM micrographs of the sintered samples revealed the presence of closed porosity, which may be the main reason of light scattering.

Lamellar eutectic structure of Al_0.7CoCrFeNi high-entropy alloy (HEA) is emerging as a promising candidate for structural applications because of its high strength-ductility combination. The alloy consists of a fine-scale lamellar fcc+B2 microstructure with high flow stresses >1500 MPa under quasi-static conditions. The response to shear loading was not investigated so far. This is the first report on the shear deformation of an eutectic structured HEA and effect of precipitation on shear deformation. The dynamic shear response (DSR) of the eutectic HEA was examined in two microstructural conditions, with and without the presence of L1₂ precipitates. A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local DSR of the alloy. The adiabatic shear bands (ASBs) in two different microstructural conditions were characterized after deformation at dynamic strain rates. The adiabatic shear localization occurs at low strains for the high strength material, and the eutectic microstructure does not delay cracking. The width of ASBs and the extent of plastic deformation around them has been correlated with the rate of straining. Dynamic recrystallization within ASBs and profuse twinning around it was observed. Local mechanical response of individual lamellae before and after shear deformation was examined using nano-indentation.

A shrimp oil rich in omega-3 lipids and carotenoids is obtained in remarkably high 5 wt% yield extending to pink shrimp processing waste (head and carapace) the circular economy approach to extract fish oil from fish processing by-products using d-limonene. Biobased limonene, a powerful antimicrobial and antioxidant agent, is an excellent solvent for both lipids and astaxanthin-based carotenoids preventing oxidative degradation during the extraction cycle including solvent and oil separation at 85°C. A new low cost route is established to extract valued marine oil from biowaste annually made available in over 2.2 million tonnes.

Sterilisation and preservation of vesicle formulations are an important consideration for their viable manufacture for industry applications, particular those intended for medicinal use. Here we undertake an initial investigation of the stability of hybrid lipid – block copolymer vesicles to common sterilisation and preservation processes, with particular interest in how the block copolymer component might tune vesicle stability. We investigate two sizes of polybutadiene-block-poly(ethylene oxide) polymers (PBd12-PEO11 and PBd22-PEO14) mixed with the phospholipid POPC considering the encapsulation stability of a fluorescent cargo and the colloidal stability of vesicle size distributions. We find that autoclaving and lyophilisation cause complete loss of encapsulation stability under the conditions studied here. Filtering through 200 nm pores appears to be viable for sterilisation for all vesicle compositions with comparatively low release of encapsulated cargo, even for vesicle size distributions which extend beyond the 200 nm filter pore size. Freeze-thaw of vesicles also shows promise for preservation of hybrid vesicles with high block copolymer content. We discuss the process stability of hybrid vesicles in terms of the complex mechanical interplay between bending resistance, stretching elasticity and lysis strain of these membranes and propose strategies for future work to further enhance the process stability of these vesicle formulations.

Owing to the reduction of rupture instability and the avoidance of wrinkle defect, hydrodynamic deep drawing (HDD) process is gradually becoming attractive for fabricating lightweight and complicated products. Meanwhile, since metallic material presents anisotropic deformation behavior, it is necessary to select an appropriate constitutive model for the prediction of plastic deformation behavior of applied material with high precision. In the present research, several anisotropic yield criteria namely, Hill’48, Yld2000-2d and BBC2005 are implemented to investigate the effect of yield functions on the prediction accuracy of the critical process window and deformation behavior for HDD process of 2024 and 5754 aluminum alloys. Material constants in the yield criteria are determined by applying uniaxial and equi-biaxial tension tests and optimizing an error-function by using the Levenberg-Marquardt algorithm. Furthermore, the process window diagram is computed utilizing the stress analytical model combined material properties with workpiece geometrical features. Numerical simulation results of predicted material anisotropic parameters, process window and HDD deformation for aluminum alloys are compared with the experimental data. Through the comparison of diverse yield criteria based on materials anisotropic coefficients, critical process window prediction, earing profile, and thickness distribution, it is revealed that the Yld2000-2d and the BBC2005 yield criteria can offer more precise models of material behavior in planar anisotropy properties for HDD process of 2024 and 5754 aluminum alloys.

Future, flexible thermal energy conversion systems require new, demand-optimized high-performance materials. The High performance Ferritic (HiperFer) stainless steels, under development at the Institute of Microstructure and Properties of Materials (IEK-2) at Forschungszentrum Jülich GmbH in Germany, provide a balanced combination of fatigue, creep and corrosion resistance at reasonable price. This paper outlines the scientific background of alloy performance development, which resulted in an age-hardening ferritic, stainless steel grade. Furthermore, technological properties are addressed and the potential concerning application is estimated by benchmarking versus conventional state of the art materials.

The article describes synthesis of aminoorgano-functionalized silica as a perspective material for catalysis application. The amino groups have electron donor properties valuable for metal chemical state of palladium. So presence of electron donor groups is important for increasing of catalysts stability. The research is devoted to investigation of silica amino-modified support influence on activity and stability of palladium species in 4-nitroaniline hydrogenation process. A series of catalysts with different supports such as SiO2, SiO2-C3H6-NH2 (amino-functionalized silica), γ-Al2O3 and activated carbon were studied. The catalytic activity was studied in the hydrogenation of 4-nitroaniline to 1,4-phenylenediamine. The catalysts were characterized by scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and pulse chemisorption of hydrogen. The 5 wt. % Pd/SiO2-C3H6-NH2 catalyst exhibited the highest catalytic activity for 4-nitroaniline hydrogenation with 100% conversion and 99% selectivity with respect to 1,4-phenylenediamine.

The paper introduces a valuable new description of fatigue strength in relation to material properties and thus a new perspective on the overall understanding of the fatigue process. Namely, a relation between the endurance limits and the accompanying values of the critical resolved shear stress (CRSS) for various metallic materials has been discovered by means of a multiscale approach for fatigue simulation. Based on the uniqueness of the relation, there is a strong indication that it is feasible to relate the endurance limit to the CRSS, and not to the ultimate strength as often done in the past.

Atomic force microscopy (AFM) has been extensively used for the nanoscale characterization of polymeric materials. The coupling of AFM with infrared spectroscope (AFM-IR) provides another advantage to the chemical analyses and thus helps to shed light upon the study of polymers. In this perspective paper, we review recent progress in the use of AFM-IR in polymer science. We describe first the principle of AFM-IR and the recent improvements to enhance its resolution. We discuss then the last progress in the use of AFM-IR as a super-resolution correlated scanned-probe IR spectroscopy for chemical characterization of polymer materials dealing with polymer composites, polymer blends, multilayers and biopolymers. To highlight the advantages of AFM-IR, we report here several results in studying crystallization of both miscible and immiscible blends as well as polymer aging. Then, we demonstrate how this novel technique can be used to determine phase separation, spherulitic structure and crystallization mechanisms at the nanoscale, which have never been achieved before. The review also discusses future trends in the use of AFM-IR in polymer materials, especially in polymer thin film investigation.

Nanoparticle (NP)–surfactants formed by the self-assembly of NPs and end-functionalized polymers at the hydrophilic/hydrophobic interface have a wide range of applications in many fields. In this study, the influence of density of amino groups, NPs dimension and pH on the interaction between end-functionalized polymers and NPs were extensively investigated. Single amino-terminated polystyrene (PS-NH2, Mw ≈ 0.6k, 2.5k, 3.5k, 3.9k) and diamino-terminated polystyrene (H2N-PS-NH2, Mw ≈ 1.1k, 2.8k) were prepared using reversible addition–fragmentation chain transfer polymerization and atom transfer radical polymerization. NPs with different dimensions (zero-dimensional carbon dots with sulfonate groups, one-dimensional cellulose nanocrystals with sulfate groups and two-dimensional graphene with sulfonate groups) in the aqueous phase were added into the toluene phase containing the aminated PS. The influence of pH and the molecular weight of amino-terminated PS on the interfacial tension between two phases were investigated. The results indicate that aminated PS exhibited the strongest interfacial activity after compounding with sulfonated NPs at a pH of 3. Terminating PS with amino groups on both ends leads to better performance in in reducing the water/toluene interfacial tension than modifying the molecular structure of PS on a single end. The dimension of sulfonated NPs also contributed significantly to the reduction of the water/toluene interfacial tension. The minimal interfacial tension was 4.49 mN/m after compounding PS-NH2 with sulfonated zero-dimensional carbon dots. Molecular dynamics simulation on the evolution of the water/toluene interface in the presence of sulfonated carbon dots and H2N-PS-NH2 revealed that these opposite charged substances moved towards the interface in an extreme short time and orderly assembled in a thermodynamic equilibrium.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS₃), a layered semiconductor that attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS₃ in air above 300 °C gradually converts it into TiO₂, a semiconductor with a wide bandgap of 3.2 eV with applications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS₃ nanoribbons and its influence on the optoelectronic properties of TiS₃-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS₃ devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase of the bandgap of titanium oxysulfide (TiO_2-xS_x) when increasing the amount of oxygen and reducing the amount of sulfur.

With increasing interest in the use of additive manufacturing techniques in the construction industry, static rheological properties of fresh concrete have necessarily come into focus. In particular, the knowledge and control of static yield stress (SYS) and its development over time are crucial for mastering formwork-free construction, e.g. by means of layered extrusion. Furthermore, solid understanding of the influences of various concrete constituents on the initial SYS of the mixture and the structural build-up rate is required for purposeful material design. This contribution is concentrated on the effect of aggregates on these rheological parameters. The volume fraction of aggregates was varied in the range of 35 to 55 % by volume under condition of constant total surface area of the particles. The total surface area per unit volume of cement paste was equal to 5.00, 7.25 and 10.00 m²/l, conditioned on the constant volume fraction of aggregates. Both variations were enabled by changing the particle size distributions of the aggregates while holding the cement paste composition constant for all concrete mixtures. To characterise the SYS and the structural build-up, constant shear rate tests with a vane-geometry rotational rheometer were performed. It was found that in the ranges under investigation the variation in volume fraction had a more pronounced effect on the static rheological properties of concrete than did the variation in surface area. An accurate mathematical description of the relationship between the initial SYS of concrete and the relative volume fraction of aggregate based on the Chateau-Ovarlez-Trung model was proposed. Challenges in deriving a similar relationship for the structural build-up rate of concrete were highlighted.

In-situ grown C_0.3N_0.7Ti and SiC, which derived from non-oxide additives Ti₃SiC₂, are proposed to densify silicon nitride (Si₃N₄) ceramics with enhanced mechanical performance. Remarkable increase of density from 79.20% to 95.48% could be achieved for Si₃N₄ ceramics with 5vol% Ti₃SiC₂. The capillarity of decomposed Si from Ti₃SiC₂, and in-situ reaction between nonstoichiometric TiC_x and Si₃N₄ were believed to be responsible for densification of Si₃N₄ ceramics. An obvious enhancement of flexural strength and fracture toughness for Ti₃SiC₂ doped Si₃N₄ ceramics was observed. The maximum flexural strength of 795 MPa for Si₃N₄ composites with 5vol% Ti₃SiC₂ and maximum fracture toughness of 6.97 MPa^.m^1/2 for Si₃N₄ composites with 20vol% Ti₃SiC₂ are achieved when mixed powders are hot-press sintered at 1700℃. Pull out of elongated Si₃N₄ grains, crack bridging, crack branching and crack deflection were demonstrated to dominate enhance fracture toughness of Si₃N₄ composites.

Curcumin and trans-cinnamaldehyde are acrolein-based Michael acceptor compounds that are commonly found in domestic condiments, and known to cause cancer cell death via redox mechanisms. Based on the structural features of these compounds we designed and synthesized several 2-cinnamamido-N-substituted-cinnamamide (bis-cinnamamide) compounds. One of the derivatives, (Z)-2-[(E)-cinnamamido]-3-phenyl-N-propylacrylamide 1512 showed a moderate antiproliferative potency (HCT-116 cell line inhibition of 32.0 µM), good selectivity profile (no inhibition of normal cell lines), and proven cellular activities leading to apoptosis. SAR studies led to more than 10-fold increase in activity. Our most promising compound, [(Z)-3-(1H-indol-3-yl)-N-propyl-2-[(E)-3-(thien-2-yl)propenamido)propenamide] 4112 killed colon cancer cells at IC50 = 0.89 µM (Caco-2), 2.85 µM (HCT-116) and 1.65 µM (HT-29), while exhibiting much weaker potency on C-166 and BHK normal cell lines (IC50 = 71 µM and 77.6 µM, respectively). Cellular studies towards identifying the compounds mechanism of cytotoxic activities revealed that apoptotic induction occurs in part as a result of oxidative stress. Importantly, the compounds showed inhibition of cancer stem cells that are critical for maintaining the potential for self-renewal and stemness. The results presented here show discovery of covalently-acting Michael addition compounds that potently kill cancer cells by a defined mechanism, with minimal effect on normal noncancerous cell.

The purpose of this study is to check out the involvement of entropy in Mpemba effect. Provided that preheating of the water the cooling duration is reduced, we theoretically show that water gains more entropy when warmed and re-cooled to the original temperature.

Coronavirus disease 2019 (COVID-19) has been first appeared in Wuhan, China but its fast transmission, led to its widespread prevalence in various countries and make it a global concern. In addition, lack of a definitive treatment is another concern that needs to be attention. Researchers have come up with several options, which are not certain, but protease inhibitor and some antiviral agent are in the forefront. In this study a virtual screening procedure employing docking of different databases including 1615 FDA approved drugs was used to identify new potential small molecule inhibitors for protease protein of COVID-19. The docking result indicates that among all, simeprevir (Hepatitis C virus (HCV) NS3/4A protease inhibitor) could fit well to the binding pocket of protease and because of some other positive features including ADME profile, might be a helpful treatment option for COVID-19.

Carbon dioxide has become a global challenge, where the emissions have become more than what could be handled. In this regard, conversion of CO2 to value added chemicals and thus recycling CO2 became a viable option. One of these options is the use of a process in strong development: oxycombustion. However, the gases resulting from this process contain some traces of impurities that can hinder the recovery of CO2 such as NO and CO. This work has therefore focused on the study of the reaction of NO reduction by CO in an oxidizing medium, using catalytic materials based on various supported noble metals. These materials were extensively characterized by a variety of methods including BET surface area measurements, hydrogen chemisorption, Transmission Electron Microscopy (TEM) and H2 temperature programmed reduction (H2-TPR). The obtained results show that the catalytic behaviour of M/Al2O3 catalysts in CO oxidation and NO reduction with CO in oxidative conditions depends mainly on the nature of the metal. The best result for these both reactions is obtained with Pt/Al2O3 catalyst. The Pt nanoparticles existing in the metallic form (Pt°) showed by TPR could explain the activity.

Behavior of supported alloyed and de-alloyed platinum-copper catalysts, which contained 14% - 27% wt. of Pt, was studied in the reactions of methanol electrooxidation (MOR) and oxygen electroreduction (ORR) in 0.1 M HClO4 solutions. Alloyed PtCux/C catalysts were prepared by a multistage sequential deposition of copper and platinum onto a Vulcan XC72 dispersed carbon support. De-alloyed PtCux-y/C catalysts were prepared by PtCux/C materials pretreatment in acid solutions. The effects of the catalysts initial composition and the acid treatment condition on their composition, structure, and catalytic activity in MOR and ORR were studied. Functional characteristics of platinum-copper catalysts were compared with those of commercial Pt/C catalysts when tested, both in an electrochemical cell and in H2/Air membrane-electrode assembly (MEA). It was shown that the acid pretreatment of platinum-copper catalysts practically does not have negative effect on their catalytic activity, but it reduces the amount of copper passing into the solution during the subsequent electrochemical study. The activity of platinum-copper catalysts in the MOR and the current-voltage characteristics of the H2/Air PEMFC MEAs measured in the process of their life tests were much higher than those of the Pt/C catalysts.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

The anodic polarization response of magnesium alloy AZ31 was characterized during exposure to aerated 0.1M NaCl solutions with millimolar additions of NaVO₃, Na₃PO₄, Na₂HPO₄, NaF and various pairings to assess their ability to inhibit corrosion kinetics and retard localized corrosion. Each of the candidate inhibitors reduced the corrosion rate of the alloy to some degree. A Na₃PO₄ - NaVO₃ pair produced a powerful inhibiting response decreasing the corrosion rate to about 10^-7 A/cm², which was two orders of magnitude lower than the uninhibited control case. A Bliss Independence assessment indicated that this inhibitor pair acted synergistically. A Na₂HPO₄ - NaVO₃ pair reduced the corrosion rate to 10^-6 A/cm² but was not assessed to be acting synergistically. The NaVO₃ - NaF pair did not reduce the corrosion rate significantly compared to the control case and was an antagonistic pairing. SEM imaging showed film formation due to exposure, which appears to be the origins of the observed inhibition. The resistance to localized corrosion was assessed as the difference in the breakdown potential and the corrosion potential with larger values indicating a lower probability of localized corrosion during free corrosion exposures. Effects of the inhibitors on this characteristic were mixed, but each of the inhibitor pairs yielded potential differences in excess of 100mV. A conceptual conversion coating process based on a mixture of vanadate and phosphate compounds were demonstrated. A fluoride-bearing formulation produced coatings whose total impedance was increased by a factor or 2 compared to an uncoated control. A fluoride-free formulation produced coatings whose corrosion resistance was increased by more than a factor of 3.

Silver particles are prepared by dewetting Ag films coated on glass using a fiber laser. The size of the particles is controlled in the range of 92 nm ~ 1.2 μm by adjusting the thickness of the Ag film. The structural properties and surface roughness of the particles are evaluated by means of scanning electron microscopy. In addition, the antifungal activity of the Ag particles is examined using spore suspensions of Colletotrichum gloeosporioides. It is shown that the particles with a size of 1.2 μm achieve 100% inhibition of the conidia growth of the Colletotrichum gloeosporioides after a contact time of just 5 min. Furthermore, the smaller particles also achieve a good antibacterial activity given a longer contact time. Similar results are observed in spore germination and pathogenicity tests performed on mango fruit and leaves. Overall, the results confirm that the Ag particles have an excellent antifungal effect on Colletotrichum gloeosporioides.

Chemical variability in the components of T. vogelii essential oils from eastern Uganda was identified using principal component analysis (PCA) and Agglomerative hierarchical clustering (AHC). Based on the profiles of the compounds of farnesene family three chemotypes were found: farnesol (chemotype 1), springene (β- Springene and α-Springene) and the β-Farnesene were distinctive in chemotype 2 and a mixed variety of farnesol and the Springene. In the three cases, alkybenzenes; o-xylene, m-xylene and ethylbenzene were significant components in the oil. 1,4-dihydroxy-p-menth-2-ene, 5,9-undecadien-2-one, 6,10-dimethyl, and 3-cyclohexen-1-carboxaldehyde,3,4-dimethyl were other prominent constituents. The yields of the essential oils did not vary significantly however the chemical composition varied with harvesting time during the rainy and dry seasons. In choice repellency tests, chemotype 1 and chemotype 2 were more active against Sitophilus zeamais than mixed chemotype. Farnesol was found to be effective only at a higher concentration as a repellent against S. zeamais. However, further study that aims to optimize and standardize the varieties and harvesting period needed for recommendation to smallhold farmers.

In order to obtain makhwean (MK) fruit essential oil of constant aromatic profile during raw material sourcing, evaluation of relationship between genotype, phenotype and chemical profiles are necessary. Three specimens of the MK (MK1-3) distributed in Northern Thailand were genetically and morphologically compared with other Zanthoxylum spices known locally as mamaad (MM) and makwoung (MKO), respectively. MM was taxonomical confirmed as Z. armatum based on plant structure and leaf characteristic (Odd-pinnately compound leaf). MKO and MK were identified as Z. rhetsa and Z. myriacanthum using number of petals and anthers. Genetic sequencing by Internal Transcribed Spacer (ITS) sequence and Random Amplified Polymorphic DNA moreover, divided these Zanthoxylum spps. into three groups accordingly to their species viz., MM, MKO and MK. Essential oil of the dried fruits from these samples was extracted and analysed for physical and chemical profiles. Cluster analysis (PCA-biplot) of volatile compositions was able to separate 1) MK1 and MK3 with limonene as leading component, 2) MK2 and MKO related with sabinene and β-philandrene, 3) MM with linalool. By using odour attribute representatives, the essential oil of MKO and MK1-3 were closely related possessing fruity, woody and citrus aromas, while the MM was sweet/ floral. In summary for MK raw material sourcing, plant genotyping played the most important role to odour characteristics than growing locations, thus plant species confirmation should be first considered.

Metallic nanoparticles (NPs), among polymeric NPs, liposomes, micelles, quantum dots, dendrimers, or fullerenes, are becoming more and more important due to their potential use in the novel medical therapies. Titanium dioxide (titanium(IV) oxide, titania, TiO2) is an inorganic compound that owes its recent rise in scientific interest to photoactivity. After the illumination in aqueous media with UV light, TiO2 produces an array of reactive oxygen species (ROS). The capability to produce ROS and thus induce cell death has found application in the photodynamic therapy (PDT) for the treatment of a wide range of maladies, from psoriasis to cancer. Titanium dioxide NPs were studied as photosensitizing agents in the treatment of malignant tumors as well as in photodynamic inactivation of antibiotic-resistant bacteria. Both TiO2 NPs themselves, as well as their composites with other molecules, can be successfully used as photosensitizers in PDT. Moreover, various organic compounds can be grafted on TiO2 NPs, leading to hybrid materials. These nanostructures can reveal increased light absorption allowing their further use in targeted therapy in medicine. In order to improve efficient anticancer therapy, many approaches utilizing titanium dioxide were tested. The most significant studies are discussed in this review.

The paper presents a synthesis of deep eutectic solvents (DESs) based on choline chloride (ChCl) as hydrogen bond acceptor and phenol (Ph), glycol ethylene (EG), and levulinic acid (Lev) as hydrogen bond donors in 1:2 molar ratio. DESs were successfully used as absorption solvents for removal of dimethyl disulfide from (DMDS) from model biogas steam. Several parameters affecting the absorption capacity and absorption rate has been optimized including kind of DES, temperature, the volume of absorbent, model biogas flow rate, and initial concentration of DMDS. Furthermore, reusability and regeneration of DESs by means of adsorption and nitrogen barbotage followed by the mechanism of absorptive desulfurization by means of density functional theory (DFT) as well as FT-IR analysis were investigated. Experimental results indicate that the most promising DES for biogas purification is ChCl:Ph, due to high absorption capacity, relatively long absorption rate, and easy regeneration. The research on the absorption mechanism revealed that van der Waal interaction is the main driving force for DMDS removal from model biogas.

On the system Au(III)-HCl-A324H⁺Cl^-, liquid-liquid extraction experiments were used to define the extraction equilibrium and the corresponding extraction constant, and the facilitated transport of this precious metal, from HCl solutions, across a flat-sheet supported liquid membrane was investigated, using the ionic liquid as carrier, as a function of hydrodynamic conditions, concentration of gold(III) (0.01-0.1 g/L), and HCl (0.5-6 M) in the feed phase, and carrier concentration (0.023-0.92 M) in the membrane. An uphill transport equation was derived considering aqueous feed boundary layer diffusion and membrane diffusion as controlling steps. The aqueous diffusional resistance (Δf) and the membrane diffusional resistance (Δm) were estimated from the proposed equation, being their values 241 s/cm an 9730 s/cm, respectively. The performance of the present carrier was compared against results yielded by other ionic liquids, and also it was investigated the influence that other metals had on gold(III) transport both from binary or quaternary solutions. Gold was finally recovered from receiving solutions as zero valent gold nanoparticles.

Over the last decades, the coated glass products, and especially the low-emissivity coatings have become a common building material used in modern architectural projects. More recently, these material systems became common in specialized glazing systems featuring solar energy harvesting. Apart from achieving the stability of optical parameters in multilayer coatings, it is also important to have improved control over the design of visual color properties of the coated glass. We prepare metal-dielectric composite (MDC) based multilayer thin-film structures using the RF-magnetron sputtering deposition and report on their optical and chromaticity properties in comparison with these obtained using pure metal-based Dielectric/Metal/Dielectric (DMD) trilayer structures of similar compositions. Experimentally achieved Hunter L, a, b values of MDC-based multilayer building blocks of coatings provide a new outlook on the engineering of future-generation optical coatings with better color consistency and developing approaches to broaden the range of achievable color coordinates and better environmental stability.

The effect of the addition of maleated polyethylene (MAPE) to compounds of natural rubber (NR) and Teline monspessulana flour (TMF) previously mercerized was investigated. Two factors were analyzed: A. concentration of MAPE with five levels 2; 4; 6; 8; 10 phr (parts per hundred rubber), B. concentration of TMF with two levels 25 and 40 phr. The effect of MAPE on compatibility between NR and HTM was evaluated by tensile testing the compounds. The mixing was performed in a laboratory scale mill. The test tubes were obtained by cutting or die-cutting crosslinked peroxide sheets, these were obtained during the compression molding process. Analysis indicate that the MAPE coupling agent improved the compatibility between HTM and NR, this effect was evidenced by the values of tensile strength and elongation at break. However, the gel content determination indicates that the addition of 10 phr of MAPE crosslinking decreases due to competition with coupling reaction MAPE - HTM.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

Hydrogen evolution reaction (HER) is one of the most important reaction in electrochemistry. This is not only because it is the simplest way to produce high purity hydrogen and the fact that it is the side reaction in many other technologies. HER actually shaped current electrochemistry because it was in focus of active research for so many years (and it still is). The number of catalysts investigated for HER is immense, and it is impossible to overview them all. In fact, it seems that the complexity of the field overcomes the complexity of HER. The aim of this review is to point out some of the latest developments in HER catalysis, current directions and some of the missing links between a single crystal, nanosized supported catalysts and, recently emerging, single atom catalysts for HER

Under pure diffusive growth conditions, layered peritectic solidification is possible. In reality, the competitive growth of the primary alfa-phase and the peritectic beta-phase revealed some complex peritectic solidification morphologies due to thermo-solutal convection. The binary organic components TRIS-NPG were used as model system for metal-like solidification. The transparency of the high-temperature non-faceted phases allows studying the dynamic of the solid/liquid interface which lead to peritectic solidification morphologies. Investigations were carried out by using the Bridgman technic for process conditions where one or both phases solidify in a non-planar manner. Different growth conditions were observed which led to competitive peritectic growth morphologies. Additionally, the competitive growth was solved numerically to interpret the observed transparent solidification patterns.

To design and optimize liquid-assisted processes such as reactive infiltration for fabricating refractory SiC/ZrSi₂ composites, basic investigations on the interfacial phenomena occurring when liquid Si-based alloys are in contact with C and SiC substrates, are key steps. Indeed, targeted wettability studies may provide helpful indications for finding the suitable set of operating conditions to succeed the fabrication of composites via the reactive infiltration and for predicting the key influencing mechanisms. The wettability of glassy carbon (GC) by two different Si-rich Si-Zr alloys as a function of the Si-content has been investigated by the sessile drop method at T = 1450°C. The more relevant results obtained in terms of equilibrium contact angle values, spreading kinetics, reactivity and developed interface microstructures are reported in the paper and compared with the behaviour previously observed in the Si-27Zr/GC system. The increase of Si-content only weakly affected the overall phenomena observed at the interface, which from the practical point of view means that even the Si-Zr alloys with higher Si-content, as respect to the eutectic alloy (Si-27Zr), could be potentially used as infiltrant materials.

In this paper, the effect of preheating on the mechanical properties and micro structure of similar friction stir welded AA6061 aluminum alloys sheets was investigated. Aluminum alloy 6061 sheets with a thickness of 5 mm and threaded cylindrical pins were used. Rotation and traverse speeds were 1200 rpm and 75 mm/min, respectively. The results of tensile tests performed on the welded samples showed that compared to the non-preheated samples, preheating had increased the strength and elongation of the joints by 58% and 46%, respectively. In the present study, during the welding process preheating cause emerged heat with lower slope from stir zone. This phenomenon may result in Increase the deformation resistance of material and consequently decrease of grain size. This grain refinement can improve the mechanical properties of welds. Accordingly, hardness and strength of the material will be increased.

Nanoparticles (NPs) have various applications in medicine, cosmetics, optics, catalysis, environmental purification, and other areas nowadays. With an increasing annual production of NPs, the risks of their harmful influence to the environment and human health is rising. Currently, our knowledge about the mechanisms of interaction between NPs and living organisms is limited. Additionally, poor understanding of how physical and chemical characteristic and different conditions influence the toxicity of NPs restrict our attempts to develop the standards and regulations which might allow us to maintain the safe living conditions. The marine species and their habitat environment are under continuous stress due to anthropogenic activities which result in the appearance of NPs in the aquatic environment. Our study aimed to evaluate and compare biochemical effects caused by the influence of different types of carbon nanotubes, carbon nanofibers, and silica nanotubes on four marine microalgae species. We have evaluated the changes in growth-rate, esterase activity, membrane polarization, and size changes of microalgae cells using flow cytometry method. Our results demonstrated that toxic effects caused by the carbon nanotubes strongly correlated with the content of heavy metal impurities in the NPs. More hydrophobic carbon NPs with less ordered structure had a higher impact on the red microalgae P. purpureum because of higher adherence between the particles and mucous covering of the algae; silica NPs caused significant inhibition of microalgae growth-rate predominantly produced by mechanical influence.

An improved method for Fluctuation Enhanced Sensing (FES) is introduced. We enhanced the old binary fingerprinting method, where the fingerprint bit values were ± 1, by introducing ternary fingerprints utilizing a reference odor. In the ternary method, the fingerprint bit values are -1, 0, and +1 where the 0 value stands for the situation where the slope of the spectrum is identical to that of the reference odor. The application of the reference odor spectrum makes the fingerprint relative to the reference. This feature increases the information entropy of the fingerprints. The method is briefly illustrated by sensing bacterial odor in cow manure isolates.

The present study focuses on the synthesis, characterization, and investigation of a p-n heterojunction photocatalysis. Titanium dioxide (TiO2) can’t alone induce the photocatalytic water splitting due to its wide bandgap, which decreases its catalytic activity in the visible light. To make redshift of absorptivity for the TiO2, Nickel (Ni)-doped Graphene (rGO) supported TiO2 was synthesized. Several characterization techniques have been employed to validate the composition and the light absorption ability of the prepared photocatalysts including TEM, SEM, EDS, XRD, XPS, and UV-Vis spectroscopy. The characterization revealed successful doping of the Ni and TiO2 on the rGO nanosheet. Moreover, the UV-Vis spectroscopy indicated a significant shift of light absorption toward the visible spectrum. The photon-induced evolution of H2 was remarkably enhanced using the prepared Ni-rGO/TiO2 nanocomposite. Furthermore, the optimum ratio of rGO: TiO2: Ni in the hybrids was 10:1:4, while the higher Ni ratio would decrease the photocatalytic activity. The stability of the photocatalyst was also verified during 8 cycles of photocatalytic reactions. The kinetic study revealed the nature of the integrated reaction and the controlling step governing the reaction sequence. .

For voltage-gated Ca2+ channel (VGCC), its α2δ subunits are traditionally considered to be auxiliary subunits that regulates VGCC trafficking to the plasma membrane. The antiepileptic, antinociceptive and anxiolytic gabapentin (GBP) has previously been shown to bind the VGCC α2δ subunits with high affinity to disrupt VGCC trafficking. Yet, the interaction between GBP and α2δ still remains poorly understood from a structural point of view. For instance, it is not clear yet what the structural implication is of α2δ-1-bound GBP against VGCC trafficking. With a set of experimental data-driven structural analysis of the VGCC α2δ-1 and its ligand GBP, this article postulates for the first time that: 1), α2δ-1 bound GBP stabilizes the α2δ-1-GBP complex structure; 2), α2δ-1 bound GBP restrains the conformational flexibility of α2δ-1; 3), α2δ-1-bound GBP establishes an electrostatic axis consisting of Q535 (Gln535)-R241 (Arg241)-GBP (gabapentin)-D452 (Asp452), which constitutes an energetically favourable contribution towards the structural stability of the α2δ-1-GBP complex and helps restrains the conformational flexibility and local structural rigidification of α2δ-1; and 4), GBP-induced local conformational inflexibility and structural rigidification of α2δ-1 is one key step in the pharmacological disruption of VGCC trafficking by GBP.

This paper addresses investigation of guided-wave excitation by angle-beam wedge piezoelectric transducers in multi-layered composite plate structure with orthotropic symmetry of the material. The aim of the present study is to determine the capability of such actuators to provide the controlled generation of an acoustic wave of a desirable type with the necessary wavelength, propagation distance and directivity. The studied CFRP panel is considered as homogenous with effective elastic moduli and anisotropic structural damping, whose parameters were determined experimentally. According to the results of dispersion analysis and taking into account the data of wave attenuation in a highly damping CFRP composite, the two types of propagating waves A0 and S0 were considered theoretically and experimentally in the frequency range 10 - 100 kHz. Using the results of a previous study, the structure of the wedge actuator was reconstructed to develop its finite element (FE) model, and a modal analysis was carried out, which revealed the most intense natural vibration modes and their eigenfrequencies within the used frequency range. Both experimental and numerical studies of the generation, propagation, directivity and attenuation of waves in the orthotropic composite panel under study revealed the influence of the angular orientation of the actuator on the formation of wave patterns and allowed to determine the capabilities of the wave's directivity control.

In this paper, the effect of multi-pass friction stir processing on the mechanical properties of AZ91 alloy has been studied. For the numerical investigation, this process has been simulated with the three-dimensional numerical modeling based on the ABAQUS/Explicit. This simulation involves the Johnson-Cook models for defining the material behavior during this intense plastic deformation and investigating the fracture criterion. The tool plunging and stirring phases in the two-pass process has been simulated. To prevent too much distortion of elements during modeling, the Arbitrary Lagrangian-Eulerian technique for automatically re-meshing of distorted elements has been used. The model was calibrated using the experimental results from the previous works. This model can predict the transient temperature distribution and residual stress field during FSP on AZ91. The results show that the maximum temperature in the advancing-side region is more than that in the retreating-side region. In addition, numerical results show that at the end position of the process, the tool during the lift-up leaves the keyhole region in the compressive stress state. The experimental results investigated the effect of multi-pass FSP on the microstructure, microhardness, tensile and creep properties of AZ91 magnesium alloy. The FSP is performed by applying 50% overlapping. The tensile, and creep tests are conducted at several temperatures from 25 to 210 °C. The optical microscopy and scanning electron micrograph (SEM) were used to study the microstructure of the samples after performing multi-pass friction stir processing. The experimental results indicate that on average, the tensile strength, microhardness, and creep strength of the processed samples increased by about 29, 23, and 38 %, respectively compared to the unprocessed ones.

NMR spectral datasets, especially in systems with limited samples, can be difficult to interpret if they contain multiple chemical components (phases, polymorphs, molecules, crystals, glasses, etc…) and the possibility of overlapping resonances. In this paper, we benchmark several blind source separation techniques for analysis of NMR spectral datasets containing negative intensity. For benchmarking purposes, we generated a large synthetic datasbase of quadrupolar solid-state NMR-like spectra that model spin-lattice T1 relaxation or nutation tip/flip angle experiments. Our benchmarking approach focused exclusively on the ability of blind source separation techniques to reproduce the spectra of the underlying pure components. In general, we find that FastICA (Fast Independent Component Analysis), SIMPLISMA (SIMPLe-to-use-Interactive Self-modeling Mixture Analysis), and NNMF (Non-Negative Matrix Factorization) are top-performing techniques. We demonstrate that dataset normalization approaches prior to blind source separation do not considerably improve outcomes. Within the range of noise levels studied, we did not find drastic changes to the ranking of techniques. The accuracy of FastICA and SIMPLISMA degrades quickly if excess (unreal) pure components are predicted. Our results indicate poor performance of SVD (Singular Value Decomposition) methods, and we propose alternative techniques for matrix initialization. The benchmarked techniques are also applied to real solid state NMR datasets. In general, the recommendations from the synthetic datasets agree with the recommendations and results from the real data analysis. The discussion provides some additional recommendations for spectroscopists applying blind source separation to NMR datasets, and for future benchmark studies. Applications of blind source separation to NMR datasets containing negative intensity may be especially useful for understanding complex and disordered systems with limited samples and mixtures of chemical components.

The ever-rising demands for energy dense electrochemical storage systems have been driving interests in beyond Li-ion batteries such as those based on lithium and magnesium metals. These high energy density batteries suffer from several challenges, several of which stem from the flammability/volatility of the electrolytes and/or instability of the electrolyte with either the negative, positive electrode or both. Recently, hydride-based electrolytes have been paving a path towards overcoming these issues. Namely, highly performing solid state electrolytes have been reported and several key challenges in multivalent batteries were overcome. In this review, the classes of hydride-based electrolytes reported for energy dense batteries are discussed. Future perspectives are presented to guide research directions in this field.

The combination of chemical cross-linking and mass spectrometry is currently a progressive technology for deriving structural information of proteins and protein complexes. In addition, chemical cross-linking is a powerful tool for stabilizing macromolecular complexes for single particle cryo-electron microscopy. Broad pallets of cross-linking chemistry, currently available for the majority of cross-linking experiments, still rely on the amine-reactive N-hydroxysuccinimide esters targeting mainly N-termini and lysine side chains. These cross-linkers are divided into two groups: water soluble and water insoluble; and research teams prefer one or another speculating on the benefits of their choice. However, the effect of cross-linker polarity on the outcome of cross-linking reaction has never been studied. Herein, we use both polar (bis(sulfosuccinimidyl) glutarate) and non-polar (disuccinimidyl glutarate) cross-linkers and systematically investigated the impact of cross-linker hydrophobicity on resulting distance constraints, using bovine serum albumin as a model protein.

The calculation of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, applying a universal computer algorithm based on the atom-groups additivity method, using refined atom groups. The atom groups are defined as the molecules' constituting atoms and their immediate neighbourhood. In addition, the hydroxy group of alcohols are further subdivided to take account of the different intermolecular interactions of primary, secondary and tertiary alcohols. The evaluation of the groups' contributions has been carried out by means of a fast Gauss-Seidel fitting calculus using experimental data from literature. Plausibility has been tested immediately after each fitting calculation using a 10-fold cross-validation procedure. For the heat capacity of liquids, the respective goodness of fit of the direct (R2) and the cross-validation calculations (Q2) of 0.998 and 0.9975, and the respective standard deviations of 8.2 and 9.16 J/mol/K, together with a medium absolute percentage deviation (MAPD) of 2.69%, based on the experimental data of 1133 compounds, proves the excellent predictive applicability of the present method. The statistical values for the heat capacity of solids are only slightly inferior: for R2 and Q2, the respective values are 0.9915 and 0.9875, the respective standard deviations are 12.19 and 14.13 J/mol/K and the MAPD is 4.65%, based on 732 solids. The predicted heat capacities for a series of liquid and solid compounds has been directly compared to those received by a complementary method based on the "true" molecular volume [1] and their deviations elucidated.

Fabrics comprised of porous fibers could provide effective passive protection against chemical and biological (CB) threats whilst maintaining high air permeability (breathability). Here, we fabricate hierarchically porous fibers consisting of regenerated silk fibroin (RSF) and activated-carbon (AC) prepared through two fiber spinning techniques in combination with ice-templating – namely cryogenic solution blow spinning (Cryo-SBS) and cryogenic wet-spinning (Cryo-WS). The Cryo-WS RSF fibers had exceptionally small macropores (as low as 0.1 µm) and high specific surface areas (SSAs) of up to 79 m2 g-1. The incorporation of AC could further increase the SSA to 210 m2 g-1 (25 wt. % loading) whilst also increasing adsorption capacity for volatile organic compounds (VOCs).

In this work, magnetic CuFe₂O₄/Ag nanoparticles activated by porous covalent organic frameworks (COF) was fabricated to evaluate the heterogenous reduction of 4-nitrophenol (4-NP). The core-shell CuFe₂O₄/Ag@COF was successfully prepared by polydopamine reduction of silver ions on CuFe₂O₄ nanoparticles, followed by COF layer condensation. With integrating the intrinsic characteristics of the magnetic CuFe₂O₄/Ag core and COF layer, the obtained nanocomposite exhibited features of high specific surface area (464.21 m² g^-1), ordered mesoporous structure, strong environment stability, as well as fast magnetic response. Accordingly, the CuFe₂O₄/Ag@COF catalyst showed good affinity towards 4-NP via π-π stacking interactions and possessed enhanced catalytic activity compared with CuFe₂O₄/Ag and CuFe₂O₄@COF. The pseudo-first-order rate constant of CuFe₂O₄/Ag@COF (0.77 min^-1) is 3 and 5 times higher than CuFe₂O₄/Ag and CuFe₂O₄@COF, respectively. The characteristics of bi-catalytic CuFe₂O₄/Ag and the porous COF shell of CuFe₂O₄/Ag@COF made a contribution to improve the activity of 4-NP reduction. The present work demonstrated a facile strategy to fabricate COF activated nano-catalysts with enhanced performance in the fields of nitrophenolic wastewater treatment.

Direct electron transfer (DET)-type bioelectrocatalysis, which couples electrode reactions and catalytic functions of redox enzymes without any redox mediator, is one of the most intriguing subjects studied over the past decades in the field of bioelectrochemistry. In order to realize the DET-type bioelectrocatalysis and to improve the performance, nanostructures of the electrode surface have to be carefully tuned for each enzyme. In addition, enzymes can also be tuned by protein engineering approach for the DET-type reaction. This review summarizes the resent progresses in this field of the research, while taking into consideration of the importance of nanostructure of electrodes as well as redox enzymes. Described are basic concepts and theoretical aspects of DET-type bioelectrocatalysis, significance of nanostructures as scaffolds for DET-type reactions, protein engineering approached for DET-type reactions, and concepts and facts of bidirectional DET-type reactions, from a cross-disciplinary viewpoint.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

Background: The aim of the present investigation was to evaluate the clinical success of horizontal ridge augmentation in the severely atrophic maxilla (Cawood and Howell class IV) using freeze-dried custom made bone harvested from cadaver donors tibial hemiplateau and to analyze the marginal bone level gain prior dental implants placement at 9 months after bone grafting and before prosthetic rehabilitation. Methods: A 52-year-old woman received custom made bone grafts. Patient underwent CT scans 2 weeks prior and 9 months after surgery for graft volume and density analysis. Results: The clinical and radiographic bone observations showed a very low rate of resorption after bone graft and implant placement. Conclusions: The custom-made allograft material was a highly effective modality for restoring the alveolar horizontal ridge, resulting in this way to reduce the need to obtain autogenous bone from a secondary site with predictable procedure. Further studies are needed to investigate its behavior at longer time points.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

Autogenous demineralized dentin matrix (ADDM), derived from human extracted tooth, is commonly used as a bone-graft substitute to reconstruct alveolar defects when placing dental implants. The purpose of this retrospective study is to examine efficacy of ADDM in terms of surgical complications and marginal bone resorption by analyzing the medical records and radiographs of patients who received ADDM graft from 2008 to 2011 in our institute. Occurrence of complications, marginal bone loss around implants were investigated with regard to the type of defect, location of bone grafting, and types of bone graft techniques. ADDM-based bone grafting was performed on 221 sites in 82 patients and 208 implants were placed afterwards: The percentage of complications after bone grafting was 15.84%, and the implant survival rate was 95.19%. All complications were resolved with conventional treatment except for the 10 cases of osseointegration failure. The average marginal bone loss was 0.31 mm at the last examination after the average follow-up period of 7.2 years. Within the limitation of this study, the results of long-term follow-up are consistent with the short-term results of relevant studies. ADDM can produce promising clinical outcomes when used for alveolar ridge augmentation around implants.

The incorporation of nanomaterials on (bio)sensors based on composite materials has led to important advances in analytical chemistry field due to the extraordinary properties that these materials offer. Nanodiamonds (NDs) are a novel type of material that has raised much attention, as they have the possibility of being produced on large scale by using relatively inexpensive synthetic methodologies. Moreover, NDs present some other interesting features as suitability for fluorescence due to surface functionalization and a proved biocompatibility, which makes them well suited for biomedical applications. In addition, NDs can be modified with metallic nanoparticles (NP), such as silver or gold, in order to combine the special features of both. The aim of this research work is the nanostructuration of novel sensing devices using NDs combined with silver (Ag@NDs) and gold (Au@NDs) nanoparticles. A complete morphological and electrochemical characterization as function of the prepared nanocomposite composition have been performed in order to improve the electroanalytical properties of the developed (bio)sensors.

Molecularly imprinted polymers (MIPs) can often bind target molecules with high selectivity and specificity. When used as MIPs, conductive polymers may have unique binding capabilities; they often contain aromatic rings, which have a great tendency to undergo covalent and hydrogen bonding interactions with similarly structured target (or template) molecules. In this work, an electrochemical method was used to optimize the synthetic self-assembly of poly(aniline-co-metanilic acid) and testosterone, forming testosterone-imprinted polymers (TIPs) on sensing electrodes. The linear sensing range for testosterone ranged from 0.1 to 100 pg/mL, and the limit of detection was as low as ~pM. Random urine samples were collected and diluted 1000 fold to measure testosterone concentration using the above TIP sensors in comparison with a commercial ARCHITECT ci 8200 system. The testosterone concentrations in the tested samples were in the range of 0.33± 0.09 to 9.13±1.33 ng/mL. The mean accuracy of the TIP-coated sensors was 90.3 ±7.0 %.

Chiroptical responses have been an essential tool over the last decades for chemical structural elucidation due to their exceptional sensitivity to geometry and intermolecular interactions. In recent times, there has been an increasing interest for the search of more efficient sensing by the rational design of tailored chiroptical systems. In this Review article, advances on chiroptical systems towards their implementation in sensing applications are summarized. Strategies to generate chiroptical responses are illustrated. Theoretical approaches to assist in the design of these systems are discussed. Development of efficient chiroptical reporters in different states of matter, essential for the implementation in sensing devises, is reviewed. In the last part, remarkable examples of chiroptical sensing applications are highlighted.

There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

PEBAX-2533/metal salt/Al salt membranes were prepared for mixed olefin/paraffin separation. PEBAX-2533 with 80% ether group and 20% amide group was suggested as the polymer matrix for comparison of separation performance according to the functional group ratio in copolymer PEBAX. In addition, Al salts were used to stabilize metal ions for a long time as additives. High permeance was expected with the proportion of high ether groups since these functional groups provided relatively permeable regions. As a result, the PEBAX-2533 composite membrane showed a selectivity of 5 (propylene/propane) with 10 GPU. However, the permeance of membrane was not unexpectedly improved and the selectivity was reduced. The result was analyzed by SEM, FT-RAMAN and TGA, including FT-IR. The reduction in separation performance was determined by FT-IR. From these results, in order to stabilize the metal ions interacting with the polymer through Al(NO3)3, it was concluded that specific ratio of amide group was needed in PEBAX as polymer matrix.

Extensive experimental and theoretical research over the past several decades has culminated in the understanding of the mechanisms behind nanoparticle-mediated enhancements on the mechanical properties of hydrogels. This information is not only crucial to realizing applications that directly benefit from developing hydrogels with high mechanical strength, but also to guide the development of strategies to further enhance hydrogel properties by combining different approaches. In our study, we investigated the effect of combining two approaches – addition of nanoparticles and crosslinking two different polymers (to create double-network hydrogels) – on the mechanical properties of hydrogels. Our studies revealed that these approaches may be combined to synthesize hydrogel composites with enhanced properties; however, both polymers in the double-network hydrogel must strongly interact with the nanoparticles to fully benefit from the addition of nanoparticles. Moreover, the concentration of hydrogel monomers used for the preparation of the double-network hydrogels had a significant effect on the extent of nanoparticle-mediated enhancements; double-network hydrogel nanocomposites prepared using lower monomer concentrations showed higher enhancements in elastic moduli compared to those prepared using high monomer concentrations. Collectively, these results demonstrate that the hypotheses previously developed to understand the role of nanoparticles on the mechanical properties of hydrogel nanocomposites may be extended to double-network hydrogel systems and guide the development of next generation hydrogels with extraordinary mechanical properties through a combination of orthogonal approaches.

Natural products have been used for the treatment of human diseases since ancient history. Over time, due to the lack of precise tools and techniques for the separation, purification, and structural elucidation of active constituents in natural resources there has been a decline in financial support and efforts in characterization of natural products. Advances in the design of chemical compounds and the understanding of their functions is of pharmacological importance for the biomedical field. However, natural products regained attention as sources of novel drug candidates upon recent developments and progress in technology. Natural compounds were shown to bear an inherent ability to bind to biomacromolecules and cover an unparalleled chemical space in comparison to most libraries used for high-throughput screening. Thus, natural products hold a great potential for the drug discovery of new scaffolds for therapeutic targets such as Sirtuins. Sirtuins are Class III histone deacetylases that have been linked to many diseases such as Parkinson`s disease, Alzheimer’s disease, type II diabetes, and cancer linked to aging. In this review, we examine the revitalization of interest in natural products for drug discovery and discuss natural product modulators of Sirtuins that could serve as a starting point for the development of isoform selective and highly potent drug-like compounds.

Meteorites represent the recoverable portions of asteroids occurring between Mars and Jupiter within the solar system that reach the surface of the Earth. Meteorites are rare extraterrestrial objects studied extensively to improve understanding of planetary evolution. In this work, calibration-free laser-induced breakdown spectroscopy (CF-LIBS) evaluates quantitative elemental and molecular analysis of the Dergaon meteorite, an H 4-5 chondrite fall sample, Assam, India. Spectral signatures of H, N, O, Na, Mg, Al, Si, P, K, Ca, Ti, Cr, Mn, Fe, Co, Ni, Ir, are measured. Along with the atomic emission, this work reports as well molecular emission from FeO molecules. The concentration of the measured elements obtained using CF-LIBS are in close agreement with earlier reports. The elements H, N and O and their concentrations are estimated using CF-LIBS for the first time. This study applies laser spectroscopy to establish presence of Ni, Cr, Co, and Ir in meteorites. Elemental analysis forms the basis for establishment of potential molecular composition of the Dergaon meteorite. Moreover, the elemental analysis approach bodes well for in-situ analyses of extraterrestrial objects including applications in planetary rover missions.

Hybrid materials of conjugated polymer and titanium(IV) oxide have attracted considerable attention concerning potential benefits, including (i) efficient exploitation of visible light, (ii) high adsorption capacity for organic contaminants, (iii) effective charge carriers separation. The new class of the photocatalysts is promising for the removal of environmental pollutants in both aqueous and gaseous phases. For the first time, in this study, the PANI/TiO₂ hybrid composite was used for the degradation of phenol in water and toluene in the gas phase. Polyaniline-TiO₂ was prepared by in-situ polymerization of aniline on the TiO₂ surface. The obtained hybrid material was characterized by diffuse reflectance spectroscopy (DR/UV-Vis), X-ray diffraction (XRD), fast-Fourier transformation spectroscopy (FTIR), photoluminescence (PL) spectroscopy, microscopy analysis (SEM/TEM) and thermogravimetric analysis (TGA). An insight into the mechanism was shown based on the photodegradation analysis of charge carriers scavengers. Polyaniline is an efficient TiO2 photosensitizer for photodegradation in visible light (λ> 420 nm). The trapping experiments revealed that mainly h+ and ˙OH were reactive oxygen species responsible for phenol degradation. Furthermore, the PANI-TiO₂ hybrid nanocomposite was used in gypsum plaster to study the self-cleaning properties of the obtained building material. The effect of PANI-TiO₂ content on hydrophilic/hydrophobic properties and crystallographic structure of gypsum was studied. The obtained PANI-TiO₂ modified gypsum plaster had improved photocatalytic activity in the reaction of toluene degradation under Vis light.

The non-structural protein NS3/4A protease is a critical factor for hepatitis C virus (HCV) maturation that requires activation by NS4A. Synthetic peptide mutants of NS4A were found to inhibit NS3 function. The bridging from peptide inhibitors to heterocyclic peptidomimetics of NS4A has not been in consideration in literature, and therefore, we decided to explore this strategy to develop a new class of NS3 inhibitors. In this report, a structure-based design approach was used to convert the bound form of NS4A into 1H-imidazole-2,5-dicarboxamide derivatives as first generation peptidomimetics. This scaffold mimics the buried amino acid sequence Ile-25` to Arg-28` at the core of NS4A21`-33` needed to activate the NS3 protease. Some of the synthesized MOC compounds were able to compete with and displace NS4A21`-33` for binding to NS3. For instance, N5-(4-guanidinobutyl)-N2-(n-hexyl)-1H-imidazole-2,5-dicarboxamide (MOC-24) inhibited the binding of NS4A21`-33` with a competition IC50 of 1.9 ± 0.12 µM in a fluorescence anisotropy assay, stabilized the denaturation of NS3 by increasing the aggregation temperature by ΔTagg 0.6 ± 0.140 ℃. MOC-24 also inhibited NS3 protease activity in a fluorometric assay. Molecular dynamics simulations rationalized the structure-activity relationship (SAR) differences between the active MOC-24 and the inactive MOC-26. Our data shows that MOC compounds are possibly the first examples of NS4A peptidomimetics that demonstrated promising activities against NS3 proteins.

Electrospinning is known to be an effective and straightforward technique to fabricate polymer non woven matrices made of nano and microfibers. Micro patterned morphology of electrospun matrices results to be outmost advantageous in the biomedical field, since it is able to mimic extracellular matrix (ECM), and favors cell adhesion and proliferation. Controlling electrospun fibers alignment is crucial for the regenerative purposes of certain tissues, such as neuronal and vascular. In this study we investigated the impact of electrospinning process parameters on fiber alignment in tubular nanofibrous matrices made of Poly (L-lactide-co-ε-caprolactone) (PLA-PCL); a Design of Experiments (DoE) approach is here proposed in order to statistically set up the process parameters. The DoE was studied keeping constants the previously set material and environmental parameters; voltage, flow rate and mandrel rotating speed were the process parameters here investigated as variables. Orientation analysis was based on ImageJ and plugin Orientation J analysis of SEM images. The results show that voltage combined with flow rate has significant impact on electrospun fiber orientation, and the greatest orientation is achieved when all the three input parameters (voltage, flow rate and mandrel rotation speed) are at their maximum value.

Microalloying of low carbon steel with niobium (Nb) and titanium (Ti) is standardly applied in high-strength low-alloy (HSLA) steels enabling austenite conditioning during thermo-mechanical controlled processing (TMCP), which results in pronounced grain refinement in the finished steel. The metallurgical effects of microalloying elements are related solute drag and precipitate particle pinning, both acting on the austenite grain boundary thereby delaying or suppressing recrystallization of the deformed grain. In that respect it is important to better understand the precipitation kinetics as well as the precipitation sequence in a typical Nb-Ti-microalloyed steel. Various characterization methods have been utilized in this study for tracing microalloy precipitation after simulating different austenite TMCP conditions in a Gleeble apparatus. Atom probe tomography (APT), scanning transmission electron microscopy in a focused ion beam equipped scanning electron microscope (STEM-on-FIB) and electrical resistivity measurements provide complementary information on the precipitation status and are correlated with each other. It will be demonstrated that accurate electrical resistivity measurements can monitor the general consumption of solute microalloys (Nb) during hot working which was complemented by APT measurements of the steel matrix. On the other hand, STEM revealed that a large part of Nb-containing particles during hot working are co-precipitated with titanium during cooling from the austenitizing temperature. Precipitates that form during cooling or isothermal holding can be distinguished from strain-induced precipitates by corroborating STEM measurements with APT results. APT specifically allows obtaining detailed information about the chemical composition of precipitates as well as the distribution of elements inside the particle. Electrical resistivity measurement, on the contrary, provides macroscopic information on the progress of precipitation and can be calibrated by APT. The current paper highlights the complementarity of these methods and shows first results within the framework of a larger study on strain-induced precipitation.

The transport of indium(III), from HCl solutions, across a supported liquid membrane in flat-sheet configuration was investigated, being the carrier the ionic liquid HA324H+Cl- (derived from the tertiary amine Hostarex A324 and hydrochloric acid). Different variables affecting the metal transport: hydrodynamic conditions in the source and receiving phases, metal and HCl concentrations in the source phase, and carrier concentration in the membrane phase, were investigated. Also the transport of indium(III) using carriers of various nature: ionic liquids, alcohol, ketone, phosphine oxide and phosphoric ester, was compared. The metal transport was modelled describing the transport mechanism as: diffusion across the source diffusion layer, a fast interfacial chemical reaction, and diffusion of the InCl4--carrier complex through the membrane support. Diffusional parameters for the transport of indium(III), from the experimental data and the model, were estimated.

Since the 1960s Rare earths (REs) applications gradually have expanded to everyday life. REs have great strategic importance in industrial and technological development, so it is expected an increase in their demand. Among the REs the European Commission considered Cerium and Lanthanum as critical raw materials. This research article studies the adsorption of Ce and La onto two carbon nanomaterials, multiwalled carbon nanotubes (MWCNT) and carboxylic functionalized multiwalled carbon nanotubes (MWCNT_ox). The latter has slightly more affinity for REs than MWCNT. The recovery percentage for Ce were 89 and 98% and in the case of for La were 99 and 92% using 0.8 g of MWCNT and 0.2 g of MWCNT_ox respectively. The adsorption process fits a pseudo second-order kinetic model and the Langmuir isotherm best represented the metal uptake.

Plastics are naturally hydrophobic materials so, in order to employ flotation for the separation of plastic mixtures, the use of appropriate wetting agents is mandatory. In this work, the effect of pretreatment with alkaline solutions of sodium hydroxide on the floatability of four plastics (PET, PS, PMMA and PVC) was studied. The influence of NaOH concentration, treatment time and temperature of the alkaline solution, and influence of particle size was analyzed. Results showed that alkaline treatment had a strong effect on PET floatability, some effect on floatability of PMMA and PVC and no effect on floatability of PS. Plastics floatability decreased with the increase of NaOH concentration, temperature and treatment time of the alkaline solution. Based on flotation behavior of simple plastics, flotation separation after alkaline treatment of bi-component mixtures of PET with PS and PVC was achieved efficiently. The best separation was obtained for PET/PS mixture, a floated with a grade of 98% in PS and a sunk with a grade of 100% in PET. PET/PMMA mixture led to the worst separation. For PET/PMMA and PET/PVC mixtures, flotation separation improved with the decrease of the particles size.

Vulcanized Rubber, as elastomer, is difficult to recycle. Today, the main end of life routes of tyres and other rubber products are landfilling, incineration in e.g. cement plants, and grinding to a fine powder, with huge quantities lacking sustainable recycling of this valuable material. Devulcanization, i.e. the breaking up of sulfur bonds by chemical, thermo-physical or biological means, is a promising route that has been investigated for more than 50 years. This review article presents and update on the state-of-the art in rubber devulcanization. This review article addresses established devulcanization technologies and novel processes described in the scientific and patent literatures. It is expected that the public discussion of environmental impacts of thermoplastics will soon spill over to thermosets and elastomers. Therefore, the industry needs to develop and market solutions proactively. Tyre recycling through devulcanization has a huge lever, since approx. 30 million tons of tyres are discarded annually.

The purpose of this study was to investigate the effect of chitosan (CS) and Alginate (Alg) polymers concentrations and CaCl2 concentration on metronidazole (MET) drug loading (LE), size particles and zeta potential. Nanocomposites were prepared by ionotropic pregelation method. A (21 *31 *21) *3= 36 full factorial design (FFD) was used to predict statistical equation and responses. The MET-CS-AlgNPs nanocomposites were characterized by X-ray diffraction, Fourier-transform infrared spectroscopy, thermal gravimetric analysis, scanning electron microscope and in vitro drug release studies. All data indicated the presence of drug into MET-CS-AlgNPs nanocomposites. The release profile of MET-CS-AlgNPs nanocomposites was found to be sustained

Efficient oxygen evolution reaction (OER) electrocatalysts are highly desired in the field of water electrolysis and rechargeable metal-air batteries. In this study, a chelate polymer, composed of copper (II) and dithiooxamide, was used to derive an efficient catalytic system for OER. Upon potential sweep in 1M KOH, copper (II) centers of the chelate polymer were transformed to CuO and Cu(OH)2. The carbon-dispersed CuO nanostructures formed a nanocomposite which exhibits an enhanced catalytic activity for OER in alkaline media. The nanocomposite catalyst has overpotential of 280 mV (at 1 mA/cm2) and a Tafel slope of 81 mV/dec in 1M KOH solution. It has a seven-fold higher current than IrO2/C electrode, per metal loading. A catalytic cycle is proposed, in which, CuO undergoes electrooxidation to Cu2O3 that further decomposes to CuO with releasing oxygen. This work reveals a new method to produce an active nanocomposite catalyst for OER in alkaline media using a non-noble metal chelate polymer and a porous carbon. This method can be applied to the synthesis of transition metal oxide nanoparticles used in the preparation of composite electrodes for water electrolyzers and can be used to derive cathode materials for aqueous-type metal-air batteries.

In this experimental report the biocompatibility of elastomeric scaffold structures made via stereolithography employing table-top 3D printer (Ember, Autodesk) and commercial resin FormLabs Flexible (FormLabs) was studied. The samples were manufactured using standard printing and development protocol, which is known to inherit cytotoxicity due to remaining non-polymerized remaining monomers, despite the polymerized material being fully biocompatible. Additional steps were taken to remedy this problem: the fabricated structures were soaked in isopropanol and methanol for different conditions (temperature, duration) in order to leach out the non-polymerized monomers. Also printed structures were UV exposed to assure maximum polymerization degree of the material. Post-processed structures were seeded with myogenic stem cells and the number of live cells was evaluated as an indicator for the material biocompatibility. The straightforward post-processing protocol enhances the biocompatibility by 7 times after 7 days soaking in isopropanol and methanol and is comparable to control (glass and polystyrene) samples. This proposes the approach as a novel and simple method to be widely applicable for dramatic cytotoxicity reduction of optically 3D printed micro-/nano-scaffolds for biomedical applications.

Galectin-3 is considered a cancer biomarker and bioindicator of fibrosis and cardiac remodeling, and, therefore, it is desirable to develop convenient methods for its detection. Herein, an approach based on the development of multivalent electrochemical probes with high galectin-3 sensing abilities is reported. The probes consist of multivalent presentations of lactose–ferrocene conjugates scaffolded on poly(amido amine) (PAMAM) dendrimers and gold nanoparticles. Such multivalent lactose–ferrocene conjugates are synthesized by coupling of azidomethylferrocene-lactose building blocks on alkyne-functionalized PAMAM, for the case of the glycodendrimers, and to disulfide‐functionalized linkers that are then used for the surface modification of citrate-stabilized gold nanoparticles. The binding and sensing abilities towards galectin 3 of both ferrocene-containing lactose dendrimers and gold nanoparticles have been evaluated by means of isothermal titration calorimetry, UV-vis spectroscopy, and differential pulse voltammetry. The highest sensitivity by electrochemical methods to galectin-3 was shown by lactosylferrocenylated gold nanoparticles, which are able to detect the lectin in nanomolar concentrations.

History is often thought to be dull and boring – where large numbers of facts are memorized for passing exams. But the past informs the present and future, especially in delineating the context surrounding specific events that, in turn, help provide a deeper understanding of their causes and implications. Scientific progress (whether incremental or breakthroughs) is built upon prior work. Chronological examination of computational chemistry’s evolution reveals the existence of major “epochs” (e.g., transition from semi-empirical methods to first principles calculations), and the centrality of key ideas (e.g., Schrodinger equation and Born Oppenheimer approximation) in potentiating progress in the field. The longstanding question of whether computing power (both capacity and speed) or theoretical insights play a more important role in advancing computational chemistry was examined by taking into account the field’s development holistically. Specifically, availability of large amount of computing power at declining cost, and advent of graphics processing unit (GPU) powered parallel computing are enabling tools for solving hitherto intractable problems. On the other hand, this essay argues (using Born Oppenheimer approximation as an example) that theoretical insights’ role in unlocking problems through simple (but insightful) assumptions is often overlooked. Collectively, the essay should be useful as a primer for appreciating major development periods in computational chemistry, from which counterfactual questions illuminate the relative importance of theoretical insights and advances in computer science in moving the field forward.

A New monogalactosyldiacylglycerol (MGDG), a known monogalactosylmonoacylglycerol (MGMG) and a known polyunsaturated fatty acid methyl ester (PUFAME) were isolated from the marine dinoflagellate Karenia mikimotoi. The planar structure of the glycolipids was elucidated using MS and NMR spectroscopic analyses and comparisons to the known glycolipid to confirm its structure. The isolation of PUFAME strongly supports the polyunsaturated fatty acid fragment of these glycolipids. The relative configuration of the sugar was deduced by comparisons of 3JHH values and proton chemical shifts with those of known glycolipids. All isolated compounds MGDG, MGMG and PUFAME (1-3) were evaluated for their antimicrobial and anti-inflammatory activity. All compounds modulated macrophage responses, with compound 3 exhibiting the greatest anti-inflammatory activity.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

TiC–high Mn steel-bonded carbide with a cellular structure was designed and fabricated by powder metallurgy techniques using coarse and fine TiC particles as the hard phase. This preparation process was carefully investigated and optimized. The microstructure of the TiC steel-bonded carbide was observed using a scanning electron microscope. Results showed that there are two types of microstructures in the TiC steel-bonded carbide: the coarse-grained TiC and fine-grained TiC. The transverse rupture strength and impact toughness of the alloy reach maximum values 2231 MPa and 12.87 J/cm2, respectively when the starting weight ratio of MP-A (containing coarse TiC particles) to MP-B (containing fine TiC particles) is 60:40. Hence, this study serves as a feasible example of how to prepare a high-strength and high-toughness TiC–high Mn steel-bonded carbide.

This study compared the mineral content and bioactive properties of flowers and fruit coming from wild elderberry plants with those of flowers and fruit harvested from elderberry cultivars grown in an orchard. Elderberry fruit and flowers were analysed for the content of selected minerals, phenolic compounds and anthocyanins and for antioxidant activity. Mineral content was determined by atomic absorption spectrometry method, while antioxidant activity and the content of polyphenols and anthocyanins were determined by spectrophotometric methods. Flowers were found to contain more total ash and to have much higher content of most of minerals, except magnesium, which was present in high concentrations in fruit. Fruit showed significantly higher antioxidant activity than flowers, whereas the total phenolic content varied depending on the growing location / cultivar. The material obtained from selected cultivars growing in an orchard had higher antioxidant activity and polyphenol and anthocyanin content than the material obtained from wild plants. Fruit of the ‘Haschberg’ cultivar and flowers of the ‘Sampo’ cultivar had the best bioactive properties of the studied samples.

This paper studies the use of zinc oxide nanoparticles (ZnO-NPs) synthesized using an extract of convolvulus leaves and expired ZnCl₂, as an efficient inhibitor for carbon steel corrosion in 1M HCl solution. ZnO-NPs are characterized by Fourier-transform infrared spectrophotometer (FTIR) and UV–Vis analysis. The technique of weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) has also been used to investigate the prevention of carbon steel corrosion in 1M HCl. The results showed that the efficiency of restraint increased when the concentration of ZnO-NPs was raised to 91% and that the inhibition efficiency is still high despite its decrease at high temperature, and it acts as a mixed-type inhibitor A sample of carbon steel with the protective inhibitor layer on top was immersed for 20 hours and observed; an increase in the charge transfer resistance (Rct) and stability of the inhibitor was noticed after 6 hours. Adsorption isotherm models demonstrated that the inhibitor adsorption mechanism on the carbon steel surface followed Langmuir, more than Freundlich and Temkin, behavior. The thermodynamic parameters showed that the adsorption process is a mixed adsorption, spontaneous, and exothermic. The results illustrated that the acid medium was a strong inhibitor of carbon steel corrosion. Scanning electron microscope (SEM) showed that the ZnO-NPs formed a good protective film on the carbon steel surface.

Highly sensitive multicomponent materials designed for the recognition of hazardous compounds request control over interfacial chemistry. The latter is key parameter in the construction of the sensing (macro)molecular architectures. In this work, multi-walled carbon nanotubes (in short, CNTs) were deposited on diazonium-modified flexible ITO electrodes prior to electropolymerization of pyrrole. This three step process, including diazonium electroreduction, deposition of CNTs and electropolymerization, provided adhesively bonded polypyrrole-wrapped CNT composite coatings on aminophenyl-modified flexible ITO sheets. The aminophenyl (AP) groups were attached to ITO by electroreduction of the in situ generated aminobenzenediazonium compound in aqueous, acidic medium. For the first time, polypyrrole (PPy) was electrodeposited in the presence of both benzenesulfonic acid (dopant) and ethylene glycol-bis(2-aminoethylether)-tetraacetic acid (EGTA) which acts as a chelator. The flexible electrodes were characterized by XPS, Raman and scanning electron microscopy (SEM) which provided strong supporting evidence for the wrapping of CNTs by the electrodeposited PPy. Indeed, the CNT average diameter increased from 182.6 nm to 274.8, 35.65.9 and 17520.1 after 1, 5 and 10 of electropolymerization of pyrrole. The PPy/CNT/NH2-ITO films generated by this strategy exhibit significantly improved stability and higher conductivity compared to a similar PPy coating without any embedded CNTs as assessed by from electrochemical impedance spectroscopy measurements. The potentiometric response was linear in the 10-83×10-7 mol.L-1 Pb(II) concentration range and the detection limit was 2.9×10-9 mol.L-1 at S/N=3. The EGTA was found to drastically improve selectivity for Pb(II) over Cu(II). To account for this improvement, density functional theory (DFT) was employed to calculate the EGTA-metal ion interaction energy which was found to be -374.6 and -116.4 kJ/mol for Pb(II) and Cu(II), respectively, considering solvation effects. This work demonstrates the power of a subtle combination of diazonium coupling agent, CNTs, chelators and conductive polymers to design high-performance electrochemical sensors for environmental applications.

High-frequency near-infrared diode laser provides high peak output, low heat accumulation, and efficient biostimulation. Although these characteristics are considered suitable for osteoarthritis (OA) treatment, the effect of high-frequency near-infrared diode laser in in vitro or in vivo OA models has not yet been reported. Therefore, we aimed to assess the biological effects of high-frequency near-infrared diode laser irradiation on IL-1β-induced chondrocyte inflammation in an in vitro OA model. Normal Human Articular Chondrocyte-Knee (NHAC-Kn) cells were stimulated with human recombinant IL-1β and irradiated with high-frequency near-infrared diode laser (910 nm, 4 or 8 J/cm2). The mRNA and protein expression of relevant inflammation- and cartilage destruction-related proteins was analyzed. IL-1β treatment significantly increased the mRNA levels of IL-1β, IL-6, TNF-α, MMP-1, MMP-3, and MMP-13. High-frequency near-infrared diode laser irradiation significantly reduced the IL-1β-induced expression of IL-1β, IL-6, TNF-α, MMP-1, and MMP-3. Similarly, high-frequency near-infrared diode laser irradiation decreased the IL-1β-induced increase in protein expression and secreted levels of MMP-1 and MMP-3. These results highlight the therapeutic potential of high-frequency near-infrared diode laser in OA.

The objective of this study was to synthesize 9-/13-position substituted berberine derivatives and evaluated their cytotoxic and photocytotoxic effects against three human cancer cell lines. Among all the synthesized compounds, 9-O-dodecyl- (5e), 13-dodecyl- (6e) and 13-O-dodecyl-berberine (7e) exhibited stronger growth inhibition against three human cancer cell lines, (HepG2, HT-29 and BFTC905), in compare with structurally related berberine (1). These three compounds also showed the photocytotoxicity in human cancer cells in a concentration-dependent and light dose-dependent manner. Through flow cytometry analysis, we found out a lipophilic group at 9-/13-position of berberine may have facilitated its penetration into test cell and hence enhanced its photocytotoxicity on human liver cancer cell HepG2. Further, in cell cycle analysis, 5e, 6e and 7e induced HepG2 cells to arrest at S phase and caused apoptosis upon irradiation. In addition, photodynamic treatment of berberine (1) and its derivatives 5e, 6e and 7e again showed a significant photocytotoxic effects on HepG2 cells, induced remarkable cell apoptosis, greatly increased intracellular ROS level and the loss of mitochondrial membrane potential. These results over and again confirmed that berberine derivatives 5e, 6e and 7e greatly enhanced photocytotoxicity. Taking together, the test data led us to conclude that berberine derivatives with a dodecyl group at 9-/13-position could be great candidates for the anti-liver cancer medicines developments.

The interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC) has been extensively utilized to synthesize nanofiltration (NF) membranes. However, it is still a huge challenge to monitor the IP reaction, because of the fast reaction rate and the formed ultra-thin film. Herein, two effective strategies were applied to reduce the IP reaction rate: (1) the introduction of hydrophilic interlayers between the porous substrate and the formed polyamide layer, and (2) the addition of macromolecular additives in the aqueous solution of PIP. As a result, in situ Fourier transform infrared (FT-IR) spectroscopy was firstly used to monitor the IP reaction of PIP/TMC with hydrophilic interlayers or macromolecular additives in the aqueous solution of PIP. Moreover, the formed polyamide layer growth on the substrate was studied in a real-time manner. The in situ FTIR experimental results confirmed that the IP reaction rates were effectively suppressed and that the formed polyamide thickness was reduced from 138 ± 24 nm to 46 ± 2 nm according to TEM observation. Furthermore, an optimized NF membrane with excellent performance was consequently obtained, which included boosted water permeation of about 141–238 (L/m²·h·MPa) and superior salt rejection of Na₂SO₄ > 98.4%.

Levan is a fructan-type exopolysaccharide, which is produced by many microbes from sucrose via extracellular levansucrases. The hydrocolloid properties of levan depend on its molecular weight, while it is unknown why and to which extent levan is functionally diverse in dependence of its size. The aim of our study was to get deeper insights into the size-dependent, functional variability of levan. For this purpose, levans of different sizes were produced using the water kefir isolate Gluconobacter albidus TMW 2.1191 and subsequently rheologically characterized. Three levan types could be identified, which are similarly branched, but significantly differ in their molecular size and rheological properties among each other. The smallest levan (< 107 Da) produced without adjustment of the pH exhibited Newton-like flow behavior up to a specific concentration of 25% (w/v). On the contrary, larger levans (> 108 Da) produced at pH ≥ 4.5 were shear-thinning and showed a gel like behavior at ≥ 5% (w/v). A third (intermediate) levan variant was obtained via production in buffers at pH 4.0 and exhibited the properties of a viscoelastic fluid at ≥ 5% (w/v). Our study reveals that the variable size and composition of levan are controllable and more decisive for its functionality than the amount of exerted levan.

Azo dyes are the most widely used synthetic dyes in the printing and dyeing process. However, the discharge of untreated azo dyes poses potential threat for human health and aqueous ecosystem. Herein, we fabricated a novel heterogenous catalyst - activated carbon fiber-supported ferric alginate (FeAlg-ACF) . Together with peroxymonosulfate (PMS) and visible light, this photocatalytic oxidation system was used to remove an azo dye - azophloxine. The results indicated that the proposed catalytic oxidation system can remove 100% azophloxine within 24 min, while under the same system, the removal rate was only 92 % and 84 % when ferric alginate was replaced with ferric citrate and ferric oxalate respectively, which showed the superiority of activated carbon fiber-supported ferric alginate. The degradation of azophloxine is achieved by the active radicals (SO4•− and •OH) released from PMS and persistent free radicals from activated carbon fiber. After treating for 24 min, the total organic carbon of azophloxine solution (50 μmol/L) decreased from 1.82 mg/L to 79.3 μg/L and the nitrate concentration of ions increased from 0.3 mg/L to 8.6 mg/L. That is, up to 93.5% azophloxine molecules were completely degraded into inorganic compounds. Consequently, potential secondary contamination by intermediate organic products during catalytic degradation was prohibited. The azophloxine removal ratio was kept almost constant after seven cycles, indicating the recyclability and longevity of this system. Furthermore, the azophloxine removal was still promising at high concentrations of Cl-, HCO3-, CO32-. Therefore, our proposed system is potentially effective to remove dye pollutants from seawater. It provides a feasible method for the development of efficient and environmental friendly PMS activation technology combined with FeAlg-ACF, has significant academic and application value.

Excessive CO₂ emissions and alternative energy fuels are two major difficult issues. The utilization of CO₂ into fine chemicals is an optimal route. Diethyl carbonate (DEC) is an extremely versatile chemical intermediate. DEC is used in gasoline, pharmaceutical, chemical and other fields. DEC synthesis from CO₂ and ethanol is a typical green synthetic route. Ni-Cu@Na₃PW₁₂O₄₀ catalysts were synthesized by two novel methods of supported and mixed. The catalyst prepared by mixed method showed nice catalytic performance. It was confirmed that water removal was the key to improving conversion efficiency. In the presence of dehydrating agent of ethylene, ethanol conversion increased from ca. 3% to ca. 40%. Propylene oxide (PO) was participated in the reaction and ethanol conversion continued to reach to ca.90% while DEC selectivity dropped by half. Under optimal conditions, our Ni-Cu@Na₃PW₁₂O₄₀ catalyst effectively solved the two major issues above.

Microbial growth has been of prime importance to the researchers in health and biotechnology industries. It has been known to be closely associated to the secretion of extracellular polymeric substances that help in the formation of colonies. Inter-microbial communication happens within such colonies by means of extracellular electron transfer mediated by the aforementioned polymeric substances. Conventionally, different phases of microbial growth are monitored with the aid of a traditional UV-Visible spectrophotometer by measuring the optical density of the liquid medium at 280 nm. In this paper, we have developed an alternative novel way to sense different growth phases employing electrochemical means i.e. two-terminal cyclic voltammetry. This cyclic voltammetry relies on the extracellular electron transfer mechanism taking place via the polymeric substances secreted by the microorganisms, measured by the temporal area changes in the current-voltage hysteresis curves in the inoculated nutrient broth. This work paves a new way to detect the biological activity in the medium, which can be directly correlated to the population of microorganisms. It would be of immense interest to scientists and researchers working in the field of microbiology as well as in development of biosensors, electrochemical sensors etc. which would be helpful in absence of traditional spectrophotometers.

The presented study is focused on the impact of binding zones locations at immunochromatographic test strips into analytical parameters of multiplex lateral flow assay. Due to non-equilibrium conditions for such assays the duration of immune reactions influences significantly on analytical parameters, and the integration of several analytes into one multiplex strip may cause essential decrease of sensitivity. To choose the best location of binding zones, we have tested reactants for immunochromatographic assays of lincomycin, chloramphenicol, and tetracycline. The influence of the distance to the binding zones on the intensity of coloration and limit of detection (LOD) was rather different. Basing on the obtained data, the best order of binding zones was chosen. In comparison with non-optimal location the LODs were 5-10 fold improved. The final assay provides LODs 0.4, 0.4 and 1.0 ng/mL for lincomycin, chloramphenicol, and tetracycline, respectively. The proposed approach can be applied for multiassays of other analytes.