The on-state voltage of MOSFETs is a convenient and powerful temperature-sensitive electric parameter (TSEP) to determine the junction temperature, thus enabling device monitoring, protection, diagnostics and prognostics. The main hurdle in the use of the on-state voltage as a TSEP is the per-device characterization procedure, to be carried out in a controlled environment, with high costs. In this paper we compare two novel techniques for MOSFET junction temperature estimation: controlled shoot-through and direct heating by resistive heaters embedded in two Kapton (polyimide) films. Both allow in-place characterization of the TSEP curve with the device mounted in its final circuit and assembly, including the working heat sink. The two methods are also validated against the conventional procedure in a thermal chamber.

Forests constitute a key component of the Earth system but the sustainability of the forest reserves in the semi-arid zone is a real concern since its vegetation is very sensitive to the climate fluctuation. The understanding of the mechanisms for the interaction vegetation-climate is poorly studied in the context of African Sahel. In this study, the characteristics of the vegetation response to the fluctuations of precipitation and temperature is determined for the forest reserve of Fina. Rainfall estimates, air temperature and NDVI are used to establish the lag correlations between fluctuations of vegetation and climate variables at both seasonal and interannual bases. Results shows increasing tendency of NDVI started from the 1990s coinciding the recovery of the rainfall from the 1980s drought and the obtained correlation(r=0.66) is statistically significant (pvalue<0.01). The strongest responses of vegetation to rainfall and temperature fluctuations were found after 30 and 15 days, respectively. Moreover, at shorter time lag (e.g. 15 days) more pronounced vegetation responses to both rainfall and temperature were found in agricultural dominated land while at longer time lag (e.g. 30 days) stronger response was observed in Bare dominated land. The vegetation response to the climate fluctuation is modulated by the land use/cover dynamics. Keywords: NDVI, Rainfall, Air temperature, vegetation response, Fina Forest Reserve, Mali.

ZnO has many technological applications which largely depend on its properties that can be tuned by controlled synthesis. Ideally, the most convenient ZnO synthesis is carried out at room temperature in aqueous solvent. However, the correct temperature values are often loosely defined. In the current paper we performed synthesis of ZnO in aqueous solvent, by varying reaction and drying temperature by 10°C steps and monitored the synthesis products primarily by XRD. We found out that a simple direct synthesis of ZnO, without additional surfactant, pumping of freezing, required both a reaction (TP) and a drying (TD) temperature of 40°C. Higher temperatures also afford ZnO, but lowering any of the TP or TD below the threshold value results either in the achievement of Zn(OH)2 or in a mixture of Zn(OH)2/ZnO. A more detailed Rietveld analysis of the ZnO samples reveals a density variation with the synthesis temperature and an increase of the nanoparticles average size also verified by SEM images. The optical properties of ZnO obtained by UV-Vis reflectance spectroscopy indicate a red shift of the band gap by ~0.1 eV.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

A Hayward black hole and magnetically charged black hole based on rational nonlinear electrodynamics with the Lagrangian ${\cal L} = -{\cal F}/(1+2\beta{\cal F})$ (${\cal F}$ is a field invariant) are considered. It was shown that the metric function in both models possesses a de Sitter core without singularities as $r\rightarrow 0$. The behavior of the Hawking temperature and the heat capacity in these models are similar. The phase transitions take place when the Hawking temperature has the maximum, and black holes are thermodynamically stable at some event horizon radii when the heat capacity is positive. We show that the source of gravity in the Hayward model is questionable.

Global population is predicted to approach 10 billion by 2050, an increase of over 2 billion from today. To meet the demands of growing, geographically and socio-economically diversified nations, we need to diversity and expand agricultural production. This expansion of agricultural productivity will need to occur under increasing biotic, and environmental constraints driven by climate change. Clustered regularly interspaced short palindromic repeats-site directed nucleases (CRISPR-SDN) and similar genome editing technologies will likely be key enablers to meet future agricultural needs. While the application of CRISPR-Cas9 mediated genome editing has led the way, the use of CRISPR-Cas12a is also increasing significantly for genome engineering of plants. The popularity of the CRISPR-Cas12a, the type V (class-II) system, is gaining momentum because of its versatility and simplified features. These include the use of a small guide RNA devoid of trans-activating crispr RNA (tracrRNA), targeting of T-rich regions of the genome where Cas9 is not suitable for use, RNA processing capability facilitating simpler multiplexing, and its ability to generate double strand breaks (DSB) with staggered ends. Many monocot and dicot species have been successfully edited using this Cas12a system and further research is ongoing to improve its efficiency in plants, including improving the temperature stability of the Cas12a enzyme, identifying new variants of Cas12a or synthetically producing Cas12a with flexible PAM sequences. In this review we provide a comparative survey of CRISPR-Cas12a and Cas9, and provide a perspective on applications of CRISPR-Cas12 in agriculture.

SARS-CoV-2 virus infections in humans were first reported in December 2019, the boreal winter. The resulting COVID-19 pandemic was declared by the WHO in March 2020. By July 2020 COVID-19 is present in 213 countries and territories, with over 12 million confirmed cases and over half a million attributed deaths. Knowledge of other viral respiratory diseases suggests that the transmission of SARS-CoV-2 could be modulated by seasonally-varying environmental factors such as temperature and humidity. Many studies on the environmental sensitivity of COVID-19 are appearing online, and some have been published in peer-reviewed journals. Initially, these studies raised the hypothesis that climatic conditions would subdue the viral transmission rate in places entering the boreal summer and that southern hemisphere countries would experience enhanced disease. For the latter, the COVID-19 peak would coincide with the peak of the influenza season, increasing misdiagnosis and placing an additional burden on health systems. In this review, we assess the evidence that environmental drivers are a significant factor in the trajectory of the COVID-19 pandemic, globally and regionally. We critically assessed 42 peer-reviewed and 80 preprint publications that met qualifying criteria. Since the disease has been prevalent for only half a year in the northern, and a quarter of a year in the southern hemisphere, datasets capturing a full seasonal cycle in one locality are not yet available. Analyses based on space-for-time substitutions, i.e. using data from climatically distinct locations as a surrogate for seasonal progression, have been inconclusive. The reported studies present a strong northern bias. Socio-economic conditions peculiar to the ‘Global South’ have been omitted as confounding variables, thereby weakening evidence of environmental signals. We explore why research to date has failed to show convincing evidence for environmental modulation of COVID-19, and discuss directions for future research. We conclude that the evidence thus far suggests a weak modulation effect, currently overwhelmed by the scale and rate of the spread of COVID-19. Seasonally-modulated transmission, if it exists, will be more evident in 2021 and subsequent years.

COVID-19 is a pandemic with no cure. There is an urgent need for low-cost interventions. Macroclimate work through affecting microclimate. In many situations, man-made microclimate, such as air conditioning, may override the effect of natural macroclimate in determining SARS-CoV-2 pathogenicity. Ambient temperature (AT) has been roughly associated to SARS-CoV-2 transmission. To translate into a feasible practice in controlling COVID-19 pandemic, in-depth and implementable knowledge of AT role in SARS-CoV-2 transmission should be unveiled. This study aimed to determine if there is a ‘safe’ temperature that is comfortable to human beings while significantly inhibitory for SARS-CoV-2 pathogenicity. Data on monthly new deaths or new cases per million population (MDPM or MCPM) and monthly cumulated days with more cases than the previous day (DI) from March 2 to June 30, 2020 were collected from all 118 countries with population over five million. Monthly average AT negatively correlated with the transmission parameters. A significant decrease in transmission was observed when AT reached above 20 ºC. Monthly average (not average high) AT of countries with MDPM <2, MCPM<10, or DI<=7 was found to be between 24.54 and 26.89 ºC (25.18 ºC on average) with average standard error of 4.81. Thus, average AT <20, 20-25, >25 ºC were considered as high, medium, and low risk AT. Furthermore, MDPM in countries with AT <20 ºC were 80.93, 50.23, 13.52, and 5.05 times of those in countries with AT >25 ºC in March, April, May, and June, respectively. MDPM low-risk rates (<2) in countries with AT >25 ºC were 100, 83.33, 52.73, and 52.46%, respectively. In countries with AT <20 ºC, the trends were opposite. Setting indoor temperature to 25 ºC could decrease the need of social distancing for containing SARS-CoV-2 transmission. Ventilation and sanitizing the air with ultraviolet light in nonbusiness hours may be additionally effective. Cooling indoor temperature too low may be a reason of COVID-19 outbreak in some high AT countries. Authorities and the general population can evaluate COVID-19 risk level and manipulate microclimate to reduce the risk anywhere anytime based on local day average AT.

Soil temperature reflects the impact of local factors，such as vegetation，soil and the atmosphere of a region. Therefore, it is important to understand the regional variation of soil temperature. However, lack of observations with adequate spatial and/or temporal coverage, it would be difficult to use the observation data to study the regional variation. Based on the observation data from Nanchang and Ganzhou stations and ERA-Interim/Land reanalysis data, this study analyzed the temporal-spatial distribution characteristics of soil temperature over Poyang Lake Basin. The results showed close correlations between observation data and reanalysis data at different depths. Reanalysis data could mainly reproduce the temporal-spatial distributions of soil temperature over the Poyang Lake Basin, but generally underestimate their magnitudes. Temporally, there is an obvious warming trend in the basin. Seasonally, the temperature raised fastest in spring and slowest in summer, except for the ST4, which rising fastest in spring and slowest in winter. In terms of depths, the temperature of ST1 rises fastest. For the other layers, the warming trend is almost similar. An abrupt change of annual soil temperature at all depths occurred in 1997, and annual soil temperatures at all depths were abnormally low in 1984. Spatially, annual soil temperature decreased with latitude, except for the summer ST1. Because of the high temperature and precipitation in summer, the ST1 are higher around the lake and the river. The climatic trend of soil temperature presents the general increase trend from south to north, opposite to the distribution of soil temperature. The findings provide a basis for understanding and assessing the variation of the soil temperature over the Poyang Lake Basin.

A novel mathematical model is developed to calculate the temperature distribution on the surface and bulk of a steel plate under the laser hardening process. The model starts with the basic heat equation then it is developed into a volumetric form and is connected to the various solid existing phases. The proposed model is based on three influencing parameters of the laser hardening process which are the velocity of the laser spot and irradiation time. The results are compared with the available experimental data reported in the literature. The volumetric model provides an assessment of temperature distribution in both the vertical and horizontal axis. Laser irradiation at sufficiently high fluence can be used to create a solid-state phase change on the surface. Primary calculations show that the temperature profile has a Gaussian distribution in horizontal x and y-axis and presents an exponentially decreasing in the horizontal and vertical depth directions.

An all-weather land surface temperature (LST) product derived at the Satellite Application Facility on Land Surface Analysis (LSA-SAF) is presented. The product is based on clear-sky LST retrieved from MSG/SEVIRI infrared (IR) measurements, complemented by LST estimated with a land surface energy balance (EB) model to fill gaps caused by clouds. The EB model solves the surface energy balance mostly using products derived at LSA-SAF. The new product is compared with in situ observations made at 3 dedicated validation stations, and with a Microwave (MW) based LST product derived from AMSR-E measurements. The validation against in-situ LST indicates an accuracy of the new product between -0.8 K and 1.1 K and a precision between 1.0 K and 1.4 K, generally showing a better performance than the MW product. The EB model shows some limitations concerning the representation of the LST diurnal cycle. Comparisons with MW LST generally show higher LST of the new product over desert areas, and lower LST over tropical regions. Several other imagers provide suitable measurements for implementing the proposed methodology, which offers the potential to obtain a global, nearly gap-free LST product.

Temperature-index modeling is used to determine the magnitude of temperature depression in the northern Sawatch Range required to maintain steady-state mass balances of six reconstructed glaciers at their extent during the local Last Glacial Maximum (LLGM), dated at ~21 ka. Assuming no significant differences in precipitation compared to modern values, mean annual temperatures in the region were on average 8.8 +0.5/–0.8 °C cooler than they are today. Allowing for modest increases or decreases in precipitation, required temperature depressions only differ by ± 0.2 °C. Temperature depression in the northern Sawatch Range are consistent, although slightly greater, with those determined in other ranges in Colorado using similar approaches. The estimates presented here are, however, substantially less than those suggested by several downscaled simulations of global LGM climate, that might be due to the need for improved calibration of such downscalings, or the models from which they are derived. Our estimates of LGM temperature depression are considerably greater than that previously determined in the study area and those in two other ranges in Colorado derived using different methodologies, the latter being most likely responsible for the discrepancies.

Nowadays industrial dryers are used instead of traditional methods for drying. In designing dryers suitable for controlling the process of drying and reaching a high quality product, it is necessary to predict the instantaneous moisture loss during drying. For this purpose, ten mathematical-experimental models with a neural network model based on the kinetic data of pistachio drying are studied. The data obtained from the cabinet dryer will be evaluated at four temperatures of inlet air and different air velocities. The pistachio seeds will be placed in a thin layer on an aluminum sheet on a drying tray and weighed by a scale attached to the computer at different times. In the neural network, data are divided into three parts: educational (60%), validation (20%) and test (20%). Finally, the best mathematical-experimental model using genetic algorithm and the best neural network structure for predicting instantaneous moisture are selected based on the least squared error and the highest correlation coefficient.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

In this paper, the effect of Bi₂O₃ doping on the mechanical properties of PbO ceramic pellets was studied. For this purpose, different ratios of Bi2O3/PbO (i.e., xBi2O3–(1-x)PbO, where x is 0, 1, 3, 5, 7 wt%) were fabricated and sintered at 570, 620, and 670°C. Mechanical properties including density, hardness, flexural strength, and sintering of PbO were studied for the aforementioned compositions. Phase compositions, microstructures, and worn surfaces of the composites were characterized by scanning electron microscopy and X-ray diffraction (XRD). The XRD analysis revealed that a solid solution formed in the composite ceramic. The best suited conditions of temperature and doping of Bi₂O₃ for optimal sintering are 620°C and 3 wt%, respectively. The hardness of the 3 wt% Bi2O3–97 wt% PbO ceramic was 717 MPa, which is about four times higher than the hardness of pure PbO; in addition, the strength of the composites was 43 MPa, which is two times higher than that of pure PbO. The integrity of the composites was verified using the lead–bismuth eutectic alloy flushing experiment. Results of this research paper are important for future studies of oxygen control in the lead–bismuth eutectic alloy of lead-cooled fast reactors.

Electrodeposition of cadmium telluride (CdTe) on fluorine doped tin oxide (FTO) using two electrode configuration was successfully achieved with the main focus on the growth temperature. The electroplating temperatures explored ranges between (55 and 85)℃ for aqueous electrolytes containing 1.5 M cadmium nitrate tetrahydrate (Cd(NO3)2 •4H2O) and 0.002 M tellurium oxide (TeO2). The ensuing CdTe thin-films were characterised using X-ray diffraction (XRD), UV-Vis spectrophotometry, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and photoelectrochemical (PEC) cell measurements. The electroplated CdTe thin-films exhibit a dominant (111) CdTe cubic structure, while the crystallite size increases with the increase in the electroplating temperature. The internal strain, dislocation density and the number of crystallites per unit area decrease with increasing growth temperature. The optical characterization depicts that the CdTe samples show comparable absorbance and a resulting bandgap of 1.51±0.03 eV for as-deposited CdTe layers. A marginal increase in the bandgap and reduction in the absorption edge slope towards lower deposition temperatures were also revealed. The annealed CdTe thin-films showed improvement in energy bandgap as it tends towards 1.45 eV while retaining the aforementioned absorption edge slope trend. Scanning electron microscopy shows that the underlying FTO layers are well covered with increasing grain size observable relative to the increase in the deposition temperature. The energy dispersive X-ray analyses show an alteration in the Te/Cd relative to the deposition temperature. Higher Te ratio with respect to Cd was revealed at deposition temperature lower than 85℃. The photoelectrochemical cell study shows that both p- and n-type CdTe can be electroplated and that deposition temperatures below 85℃ at 1400 mV results in p-type CdTe layers.

Abstract: The Inconel 625 is a nickel-based alloy has been widely used in the high-temperature application. The Inconel 625 exhibits unstable plastic flow at elevated temperature characterized by serrated yielding, known as Portevin-Le Chatelier effect. The aim of this work is to evaluate the mechanical properties at high temperatures of the Inconel 625. The tensile tests were performed in the temperature range of room temperature until 1000 °C and strain rate of 2x10^-4 to 2x10^-3 s^-1. The creep tests were performed in the temperature range of 600-700 °C, in the stress range of 500-600 MPa in a constant load mode. The surface fracture was observed by optical and scanning electron microscopy. Serrated stress-strain behavior was observed in the curves obtained at 200 to 700 °C, which was associated with the dynamic strain aging effect. The yield strength and the elongation values show an anomalous behavior as a function of the test temperature. An intergranular cracking was observed specimen tensile tested at 500 °C that can be attributed to the decohesion of the carbides along the grain boundaries. The fracture surface of the specimen tensile tested at 700 °C showed the predominance of transgranular cracking with tear dimples with a parabolic shape.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

Epidemiological studies indicate an increased risk of cancer from the consumption of very hot foods and beverages. The International Agency for Research on Cancer (IARC) has already recommended threshold values for the maximum drinking temperature of very hot beverages. The contact time and the contact temperature are decisive for the risk of injury when hot media come into contact with human skin. However, measuring the contact temperature is not easily possible in practice. In the present study, a numerical simulation based on the solution of the heat conduction equation was initially used to investigate whether and for what period of time a constant contact temperature is to be expected under oral conditions. For small circular 3-cm food samples (e.g., cooked potatoes) with 2.5 mm thickness in contact with the tongue, the simulation results in a constant contact temperature of 10 s before cooling. With a thickness of 0.5 mm, the contact temperature is only maintained 1 s. Hot beverages, which spread as a thin film and thereby increase their surface area, can therefore be consumed at higher temperatures than solid foods. Furthermore, a simple test technique with a "measuring spoon" was developed. A hot sample is placed on the tongue. Orientating measurements were used to determine which contact temperature was considered to be just comfortable for any period > 10 s and for which period of less than 10 s it was still just bearable. The contact temperature, which was still perceived as tolerable for periods > 10 s, was 46.5 °C. The time spans for the higher contact temperature 48 °C were between 2 and 4 s and for 49 °C between 1 and 2 s. The course of the contact temperatures determined in the experiment over time allows to calculate the corresponding threshold values of consumption temperatures for various foods. Consumption temperatures of about 56 °C for potatoes and 60 °C for cheese are still perceived as tolerable. In view of the fact that the contact temperature is obviously the determining factor for the risk of injury from burns in the oral cavity in addition to the contact time, it makes sense to reference threshold values to the contact temperature rather than to the surface or consumption temperature of a food product, which is current customary practice. If this contact temperature is defined as a threshold value, the surface or consumption temperature for any other food can be calculated.

Renewable sources and electric distribution network can produce or make available a surplus of electric and thermal energies. The Intermediate Temperature Solid Oxide Electrolyzer (IT-SOE) fed by CO2-steam mixtures can store these electric and thermal energies producing CO-H2 mixtures with high conversion efficiency. Inside the IT-SOE, the CO2-steam mixtures are converted to CO-H2 mixtures and O2 through the cathode and anode electrochemical reactions and reverse water gas shift chemical reaction. In this article an IT-SOE stack fed by different types of steam mixtures was tested at different operating temperatures and the stack polarization and electric power curves were detected experimentally. At the highest hydrogen production operating temperature of the stack fed by steam mixtures, the experimental polarization and electric power curves of the stack fed by steam and CO2-steam mixtures were compared. A simulation model of the IT-SOE system (stack and furnace) fed by CO2-steam mixtures was formulated ad hoc and implemented in a Matlab environment and experimentally validated. At the highest hydrogen production stack operating temperature, the IT-SOE system thermal equilibrium current was evaluated through the simulation model. Moreover, the influence of this current on the IT-SOE system efficiency and the CO-H2 mixture degree of purity was highlighted.

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

Leaf temperature (T_leaf) influences photosynthesis and respiration. Currently, there is a growing interest on including lianas in productivity models due to their increasing abundance, and their detrimental effects on net primary productivity in tropical environments. Therefore, understanding the differences of T_leaf between lianas and trees is important for future of forest on whole ecosystem productivity. Here we determined the displayed leaf temperature (T_d= T_leaf – ambient temperature) of several species of lianas and their host trees during ENSO and non-ENSO years to evaluate if the presence of lianas affects the T_d of their host trees, and if leaves of lianas and their host trees exhibit differences in T_d. Our results suggest that close to midday, the presence of lianas does not affect the T_d of their host trees; however, lianas tend to have higher values of T_d than their hosts across seasons, in both ENSO and non-ENSO years. Although lianas and trees tend to have similar physiological-temperature responses, differences in T_d could lead to significant differences in rates of photosynthesis and respiration based temperature response curves. Future models should thus consider differences in leaf temperature between these life forms to achieve robust predictions of productivity.

Global climatic event on Middle Miocene triggered by geology activity is called by Mid- Miocene Climatic Optimum (MMCO). This event was widely distributed and associated with increasing temperature and CO2 content in the atmosphere. The effect of MMCO was widely known the mid-latitude region, but still limited information in low latitude sediments. This study try to perform the effect of MMCO at Cibulakan Formation in which deposited in the low latitude basin, Bogor Basin. Fifty eights samples from Cileungsi River were taken at Cibulakan Formation and quantitative nannoplankton analysis was carried out for this study. Nannoplankton shows the sensitive response with sea surface temperature changes. Increasing of total population nannoplankton indicates the rising of temperature and dropping temperature is marked by decreasing population. The effect of sea surface temperature changes relates with salinity changes as the effect of evaporation. Helicosphaera carteri and Umbilicosphaera jafari were counted to know the salinity trend at Cibulakan Formation. Sea surfaces temperature changes was observed on Early Miocene which was influenced by small scale Early Miocene glaciation and active tectonic during this period. Warming temperature taken place on Middle Miocene as the effect of warm and open sea during Mid Miocene Climatic Optimum. Afterwards, hot temperature continued on Late Miocene triggered by global increasing temperature at Pacific Ocean and widely distribution of clean water at North West Java Basin.

Terrestrial vegetation dynamics are closely influenced by a multitude of factors. This study investigated the relationships between vegetation patterns and their main influencing factors. The joint entropy method was employed to evaluate the dependence between normalized difference vegetation index (NDVI) and coupled variables in the middle reaches of Hei River basin. Based on the spatial distribution of mutual information, the whole study area was divided into five sub-regions. In each sub-region, nested statistical models were applied to model the NDVI on the grid and regional scales, respectively. Results showed that the annual average NDVI increased with a rate of 0.005/a in recent 11 years. In the desert regions, the NDVI increased significantly with an increase in precipitation and temperature, and high accuracy of retrieving NDVI model was obtained by coupling precipitation and temperature, especially in sub-region I. In the oasis regions, groundwater was also an important factor driving vegetation growth, and the rise of groundwater level contributed to the growth of vegetation. However, the relationship was weaker in artificial oasis regions (sub-region III and sub-region V) due to the influence of human activities, such as irrigation. The overall correlation coefficient between the observed NDVI and modeled NDVI was observed to be 0.97. Outcomes of this study are suitable for ecosystem monitoring, especially under the realm of climate change. Further studies are necessary and should consider more factors, such as runoff and irrigation.

For broadcast spawning invertebrates such as the crown-of-thorns starfish, early life history stages (from spawning to settlement) may be exposed to a wide range of environmental conditions, and could have a major bearing on reproductive success and population replenishment. Arrested development in response to multiple environmental stressors at the earliest stages can be used to define lower and upper limits for normal development. Here, we compared sperm swimming speeds and proportion of motile sperm and rates of fertilization and early development under a range of environmental variables (temperature: 20-36°C, salinity: 20-34 psu, and pH: 7.6-8.2) to identify environmental tipping points and thresholds for reproductive success. We also tested the effects of water-soluble compounds derived from eggs on sperm activity. Our results demonstrate that gametes, fertilization, and early development are robust to a wide range of temperature, salinity, and pH levels that are outside the range found at the geographical limits of adult distribution and can tolerate environmental conditions that exceed expected anomalies as a result of climate change. Water-soluble compounds associated with eggs also enhance sperm activity, particularly in environmental conditions where sperm motility is initially limited. These findings suggest that fertilization and embryonic development of crown-of-thorns starfish are tolerant to a wide range of environmental conditions, though environmental constraints on recruitment success may occur at later ontogenic stages.

Multivariate statistical approaches (MSA), such as principal components analysis and multidimensional scaling, seek to uncover meaningful patterns within datasets by considering multiple response variables in a concerted fashion. Although these techniques are readily used by ecologists to visualize and explain differences between study sites, they could theoretically be employed to differentiate organisms within an experimental framework while simultaneously identifying response variables that drive documented experimental differences. Therefore, MSA were used herein to attempt to understand the response of the common, Indo-Pacific reef coral Seriatopora hystrix to temperature changes using data from laboratory-based temperature challenge studies performed in Southern Taiwan. Gene expression and physiological data partitioned experimental specimens by time of sampling, treatment temperature, and site of origin upon employing MSA, signifying that S. hystrix and its dinoflagellate endosymbionts display physiological and molecular signatures that are characteristic of sampling time, site of colony origin, and/or temperature regime. These findings promote the utility of MSA for documenting biologically meaningful shifts in the physiological and/or sub-cellular response of marine invertebrates exposed to environmental change.

Machine Learning (ML) was used to assess and predict urban air temperature (Tair) considering the complexity of the terrain features in Yerevan (Armenia). The estimation was performed based on the PLSR model with a high number (30) of input variables. The relevant parameters include a newly purposed modification of spectral index IBI-SAVI, which turned out to be strongly impacting on Tair prediction together with land surface temperature (LST). Cross-validation analysis on temperature predictions across a station-centered 1000m circular area revealed quite a high correlation (R2Val = 0.77, RMSEVal = 1.58) between predicted and measured Tair from the test set. It was concluded the remote sensing is an effective tool to estimate Tair distribution where a dense network of weather stations is not available. However, further developments will include incorporation of additional weather parameters from the weather stations such as precipitation and wind speed, and the use of non-parametric ML techniques.

The distribution of impervious surface is one of the important assessment indicators for evaluating the quality of urban ecological environment. Taking Xuzhou city as an example, we study the influence of the spatial distribution of impervious surfaces on urban surface temperature, using Landsat 8 remote sensing imagery and nighttime lighting data to extract the impervious surface information from 2013 to 2022 and carry out surface temperature inversion. The study area was divided into built-up and non-built-up areas using nighttime lighting data and the relevant indices were used to establish interest zones and finally the extraction of impervious surfaces was completed using supervised classification methods. The experimental results show that the kappa coefficient is not less than 0.8562, which makes the result more reliable. By extracting the impervious surface of Xuzhou City, it was found that the impervious surface of Xuzhou City continued to increase from 2013 to 2022, in which the growth rate was faster in 2014-2016 and 2019-2021, and slowed down in 2017-2018 and 2021-2022. The expansion of impervious surface was found to be one of the reasons for the increase of urban surface temperature through stacked analysis and linear regression analysis.

Agroclimatic indicators help convey information about climate variability and change in terms that are meaningful to the agricultural sector. This study evaluated climate projections for Angola, particularly for provinces with higher agrarian potential. To this end, a set of 15 predefined agroclimatic indicators in 2041–2070 and 2071–2099, under the anthropogenic forcing scenarios RCP4 and RCP8, were compared with the historical period 1981–2010 as a baseline. Data were extracted within the geographic window of longitudes 10–24°E and latitudes 4–18°S and from five climate model chain experiments, namely MIROC-ESM-CHEM, HadGEM2-ES, IPSL-CM5A-LR, GFDL-ESM2M and NorESM1-M. The averages of the set of agroclimatic indicators, as well as their differences between historical and future periods, are discussed concerning the likely implications for agriculture in Angola. The results show significant increases in average daily maximum (2–3°C) and minimum (2–3°C) temperatures in Angola. For the future, a generally significant reduction in precipitation (and its associated indicators) is expected in all areas of Angola, with the southwest region (Namibe and Huíla) recording the most pronounced decrease, up to 300 mm, while the maximum number of consecutive dry days will increase across the country and especially in the northeast of the country. A widespread increase in temperatures is expected, which could lead to hot and dry conditions in Angola that could lead to more frequent, intense and prolonged extreme events, such as tropical nights, maximum number of consecutive summer days, warm and wet days and Warm spell duration index periods. These changes can seriously affect agriculture, water resources and ecosystems in Angola, thus requiring adaptation strategies to reduce risks and adverse effects, while ensuring the sustainability of the country's natural resources and guaranteeing its food security.

The temperature sensors play important roles in wide spreading human activities. Non-contact method has great advantages, but the detection precision encounters big challenge. In this work, a double-layer asymmetric terahertz (THz) metamaterial combined with phase transition oxide was proposed to realize non-contact temperature sensor with high sensitivity. The metamaterial exhibits band-stop filtering effects in the simulated transmission spectra. Temperature changes induce a reversible phase transition in VO2, resulting in altered conductivity. Numerical results indicate that the S21 parameter increases from -44.33 dB to -4.78 dB at a frequency of 1.22 THz as the conductivity of the VO₂ film increases from 10 to 5000 S/m, achieving a modulation depth of 89%. This work provide a great insights for the development of metamaterials based high-precision temperature measurement.

The study investigates methods to enhance the reliability of NO2 monitoring using low-cost electrochemical sensors to measure gaseous pollutants in air by addressing the impacts of temperature and relative humidity. The temperature within a plastic container was controlled using an internal mica heater, an external hot air blower or cooling packs, while relative humidity was adjusted using glycerin solutions. Findings indicated that the Auxiliary Electrode (AE) signal is susceptible to temperature and moderately affected by relative humidity. In contrast, the Working Electrode (WE) signal is less affected by temperature and relative humidity; however, adjustments are still required to determine gas concentrations accurately. Tests involving on/off cycles showed that the AE signal experiences exponential decay before stabilizing, requiring the exclusion of initial readings during monitoring activities. Additionally, calibration experiments in zero air allowed the determination of the compensation factor nT across different temperatures and humidity levels. These results highlight the importance of compensating for temperature and humidity effects to improve the accuracy and reliability of NO2 measurements using low-cost electrochemical sensors. This refinement makes the calibration applicable across a broader range of environmental conditions. However, the experiments also show a lack of repeatability of the zero calibration.

This article presents the results of analyzing emergency situations that lead to substantial economic losses during recovery efforts. Various technical solutions are explored that can identify the onset and, in some cases, the duration of natural or technical factors influencing the occurrence of such emergencies. The relevance of developing a combined protection system for wind generators is substantiated. The system comprises a three-tier structure. The first, lowest level, collects real-time data on monitored parameters. The second level stores this data, calculates missing coordinates using observers, and generates warning messages for wind generator operators about potential emergency situations. The third, highest level, includes the operator's computer. This combined protection system plays a crucial role in reducing emergency occurrences and enhancing the reliability and lifespan of wind generators.

This study examines stress distributions in adhesive joints under various loading and temperature conditions. Finite element analysis (FEA) was employed to compute the peel and shear stresses at the adhesive interface and bondline mid-section. Dependency analysis shows that mid-section peel stress significantly impacts the experimental shear strength of SLJs more than shear stress. This insight highlights the need to carefully analyze peel stress and bending moment factors. The analytical solutions proposed by Goland and Reissner were analyzed with modifications by Hart-Smith and Zhao. Hart-Smith’s approach performed more effectively, especially when the adhesive layer thickness (t_a) is 0.5 mm and the overlap length to thickness ratio (c/t_a) is ≥20. FEA revealed stress distributions at the adhesive/adherend interface and bondline mid-section. DP490 adhesive joints exhibited lower stresses than EA9696. Temperature variations significantly affected joint behavior, particularly above the adhesive’s glass transition temperature (T_g). Both EA9696 and DP490 adhesive joints displayed distinct responses to stress and temperature changes. The parabolic and biquadratic solutions for functionally graded adhesive (FGA) joints were compared. The biquadratic solution consistently yielded higher shear and peel stress values, with an increase ranging from 15% to 71% compared to the parabolic solution at various temperatures because of larger gradient of the Young's modulus distribution near the overlap ends. The ratio of peak peel stress to peak shear stress suggests selecting an adhesive with a superior peel strength or primarily reducing the peak peel stress by functionally grading is advisable, particularly if the adhesive is brittle. Comparison of stress distributions emphasize the importance of selecting adhesives based on stress type, temperature, and solution methods in optimizing adhesive bonding applications. These findings provide valuable insights for thermomechanical applications where thermal stimuli may be used for controlled debonding.

This paper presents design and optimization of a small-size electromagnetic induction heating control system powered by a 3.7V-900mAh lithium battery and featuring an LC series resonant full bridge inverter circuit, which can be used in small size materials heating applications, such as micro medical devices. The effects of resonant capacitance, inductor wire diameter, heating tube material and wall thickness are studied to maximize the heating rate of the workpiece and meantime reduce the temperature rise of the NMOS transistor. The optimal circuit configuration meeting the design requirements was finally identified via comparing the operational parameters and NMOS transistor loss under different circuit conditions. The validation experiments were conducted on a designed electromagnetic induction smoking devices. The results indicate that under an output current of 4.6A, the heating tube can reach up to the temperature target of 250℃ within 11 seconds, and all NMOS transistors stay below 50°C in a 5 minutes heating process.

This study explores the inelastic doubly differential transverse momentum spectra of the primary charged particles, (π + + π − ), (K + + K − ) and (pp̄) as a function of underlying event √ (UE) at s = 13 T eV . The particle production is measured on the basis of different angular regions like toward, transverse and away, elucidated with respect to the direction of leading particle of an event. To study the thermal freeze-out parameters, the non extensive Tsallis distribution function is used, to extract the temperature Tef f , and chemical potential µ, which provides a basis to explain the QCD matter. The Tsallis distribution function clearly describes transverse momentum spectra in pseudorapidity region of |η| < 0.8. The best fit corresponds to minimum χ2 /ndf value for the transverse momentum distribution. It is observed that effective temperature Tef f changes from away to towards and forward region.

High entropy alloys have excellent wear resistance, so they have great application prospects in the fields of wear resistance and surface protection. In this study, the wear resistance of FeNiCrCoCu high entropy alloy coating was systematically analyzed by molecular dynamics method. FeNiCrCoCu high entropy alloy was used as a coating material to adhere to the surface of Cu matrix. The friction and nano indentation simulation of this coating material were carried out by controlling the ambient temperature. The influence of temperature on its friction properties was analyzed from five aspects: lattice structure, dislocation evolution, friction coefficient, hardness and elastic modulus. The results show that with the increase of temperature, the disorder of the lattice structure increases, which leads to the increase of the tangential force and the friction coefficient in the friction process. At 300K and 600K, the ordered lattice structure of the high entropy alloy coating material is basically the same, and thus their hardness is basically the same. However, the dislocation density at 600K is significantly reduced compared with that at 300K, resulting in the increase of the elastic modulus of the material from 173GPa to 219GPa. At the temperatures of 900K and 1200k, lattice disorder take place rapidly, and dislocation density also decreases significantly, resulting in a significant decrease in the hardness and elastic modulus of the material. When the temperature reaches 900K, the wear resistance of the FeNiCrCoCu high entropy alloy coating decreases sharply. This work is of great value to the analysis of wear resistance of high entropy alloy at high temperature.

During the last 100 years the planet has increased its temperature rapidly, this climate change could bring catastrophic effects for organisms and natural systems. One of the most affected groups is the ectotherms, due to their direct dependence on the environmental temperature. In recent years several studies analyse the effects of temperature and the thermal tolerance on several species of ectotherms. However, there are species whose thermal tolerances are still unknown. Such is the case of critically endangered species the Montseny Brook Newt (Calotriton arnoldi), endemic from the Montseny massif in Spain and whose thermal biology is unknown. Its critical situation makes essential to know its tolerance to cooling, warming and thermopreferendum in water environment where the newt lives. Three experimental procedures were conducted from the western and eastern subpopulations of C. arnoldi considering four classes separately (males, females, juveniles and larvae). The results obtained showed that the CTmax of the species exceeded 31°C, with a significant difference between the two populations. We found that the species tolerates well low temperatures (&lt;1°C), because of the genera Calotriton is adapted to lives in cold waters with temperatures below 15º. Although the thermopreference of the species was expected to trend to cold temperatures, some individuals chose relatively high temperatures, obtaining a range of 11.7°C to 21.6°C. The results presented in this study are an advance in the knowledge of the thermal physiology of this species and support the importance of the temperature of the torrent on its survival. Knowing their thermal limits and their preferred temperature range will help to propose management measures that promote the conservation of streams and its riparian forest cover to mitigate the temperature increase due to climate change.

In this study, using information theory tools, we investigate the quantum degree of mixedness, particle number fluctuations, and temperature variations in the paradigmatic Lipkin model, focusing on the interplay between these factors in a system of many fermions. Our analysis reveals intriguing dependencies of quantum mixedness on the total fermion number, showcasing distinct behaviors at different temperatures. Notably, we find that the degree of quantum mixedness exhibits a strong dependence on the total fermion number, with varying trends observed across different temperature regimes. Remarkably, this dependence remains unaffected by the strength of the fermion-fermion interaction (if it does not vanish, of course), underscoring the robustness of the observed phenomena. Through comprehensive numerical simulations, we provide illustrative graphs that depict these dependencies, offering valuable insights into the fundamental characteristics of many-fermion systems. Our findings shed light on the intricate dynamics of quantum degree of mixedness and particle number fluctuations in fermionic systems, with potential implications for diverse fields ranging from condensed matter physics to quantum information science.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Background: Many clinical conditions are affected by meteorological factors and climate changes. Psychiatric disorders are large contributors to the global disease burden, but the literature on the impact of climate changes on mental health is limited. The aim of this study is to investigate the correlation between rising temperatures and admissions for acute exacerbations of psychiatric disorders. Methods: Data were collected for summer months of years 2013 to 2022. Mean monthly tempera-tures were obtained from the meteorological station of the Department of Physics of the Universi-ty of Turin. Data on patients admitted to the acute psychiatric unit of San Luigi Gonzaga Univer-sity Hospital (Turin, Italy) were extracted from the hospital registry. Linear regression analyses were used to investigate the correlation between temperature and number of admissions. Results: A total of 1600 admissions to our psychiatric ward were recorded. Mean monthly temper-ature and monthly number of admissions were directly correlated (P = 0.0020). The correlation between temperature and admissions was significant for the subgroup of admissions due to Bipo-lar Disorders (BD) (P=0.0011), but not for Schizophrenia (P=0.6070) (SCZ) or Major Depressive Disorder (MDD) (P=0.0588). Conclusions: These results confirm the impact of meteorological factors on mental disorders, and in particular on the course of BD. This provides new insights into etiopathological mechanisms and can contribute to improved follow up and relapse prevention.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

Shape-shifting polymers are widely used in various fields such as intelligent switches, soft robots and sensors, which require both multiple stimulus response functions and qualified mechanical strength. In this study, a novel near infrared light (NIR) responsible shape-shifting hydrogel system was designed and fabricated, through embedding vinylsilane modified carbon nanotubes (CNTs) into particle-double network (P-DN) hydrogels by micellar copolymerization. The dispersed brittle Poly(sodium 2-acrylamido-2-methylpropane-1-sulfonate) (PNaAMPS) network of the microgels can serves as sacrificial bonds to toughen the hydrogels, and the CNTs endow it NIR photothermal conversion ability. The results show that the CNTs embedded P-DN hydrogels present excellent mechanical strength, i. e. fracture strength of 312 kPa and fracture strain of 357%. Moreover, an asymmetric bilayer hydrogel, where the active layer contains CNTs, can achieve 0°–110° bending deformation within 10 min under NIR irradiation and can realise complex deformation movement. This study provides a theoretical and experimental basis for the design and manufacture of photoresponsive soft actuators.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

In recent years, green and healthy foods have attracted much attention. Plant-based foods have become a new trend to replace animal-derived foods. In this study, we used walnut and purple rice as the primary raw materials to produce yogurt. The process included boiling, mixing, grinding, inoculation, fermentation, and sterilization. We then analyzed the similarities and differences between the resulting walnut purple rice yogurt and unfermented walnut purple rice milk, as well as dairy-based yogurt, in terms of physical chemistry, flavor, and sensory characteristics. We also examined the similarities and differences between fermented walnut purple rice milk and conventional warm yogurt. The study results revealed that walnut purple rice yogurt exhibited greater viscosity than walnut purple rice milk and conventional dairy-based yogurt. Additionally, the former displayed enhanced stability and recovery ability. Notably, distinguishable differences were observed between the three types of yogurts in terms of the presence of unknown volatiles and the umami signal as indicated by electronic nose/tongue and GC-IMS analyses. The umami flavour of walnut purple rice yogurt surpasses that of traditional dairy-based yogurt, whilst its salty taste is lower than that of walnut purple rice milk. Despite possessing a weaker aroma than dairy-based yogurt, it is more potent than walnut purple rice milk. Additionally, its relative abundance of olefins, ketones, and alcohols enhances its unique flavour profile, surpassing both other options. Based on sensory analysis, it can be deduced that walnut purple rice yogurt has the highest overall acceptance rate.

The identified Urban Heat Island (UHI) phenomenon, coupled with diminished vegetation and anthropogenic heat release, poses a significant environmental challenge for major urban centers. Particularly worrisome is the UHI effect in hot and temperate climates such as the Mediterranean region during the summer season. This exacerbates discomfort and heightens the risks of diseases linked to high temperatures. Additionally, it contributes to environmental consequences, including elevated electricity consumption due to increased demand for cooling [1]. The utilization of Remotely Sensed imagery for estimating Land Surface Temperature has become more prevalent in various applications associated with evaluating urban micro-climates and the Urban Heat Island (UHI) phenomenon. This study presents an algorithm for the automatic mapping of Land Surface Temperature (LST) from Landsat-8 data using a vegetation index-based technique in the Google Earth Engine (GEE) platform. The primary aim is to discern patterns and trends in LST over a 5-year period, from 2017 to 2021. The application was tested in the urban area of Thessaloniki, Northern Greece, which is particularly representative of the Mediterranean urban environment. Computation of Normalized Difference Indices (NDVI, NDBI, NDWI) for the study area was also performed within the GEE platform and correlation analysis was implemented to evaluate the impact of the urban landscape on the distribution of LST.

Global climate change has induced a rise in sea surface temperature (SST), although this increase is not uniform across the world. Significant variations exist between coastal and offshore waters, particularly in regions affected by upwelling processes. This study focuses on the Canary Current Upwelling System (CCUS), stretching from Northwest Iberia to Northwest Africa. High-resolution remotely sensed SST data (0.05°) from the ODYSSEA Level 4 Sea Surface Temperature Reprocessed dataset were validated with in-situ measurements and employed to establish a regional climatological baseline for 1982 – 2012. Subsequent years were compared to this baseline to construct SST anomaly maps, revealing SST changes since 2012. The study area was further divided into sub-regions for comparative analysis. Results indicate that SST consistently increased at a higher rate offshore compared to the adjacent nearshore regions. A reference dataset spanning 1951 – 1981 was used to gauge SST variability between the two baselines. SST exhibited a 0.59°C increase from 1951 – 1981 to 1982 – 2012, with a slowing of SST trends beyond the 1982 – 2012 baseline. This research offers valuable insights into the climatological dynamics of the CCUS. These findings enhance our understanding of this critical coastal system's climatology, laying the groundwork for future investigations into evolving climate patterns in coastal regions.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

Grouting materials with good insulation and reinforcement performance are key factors in solving the temperature control problem of high temperature tunnels using curtain grouting, while existing grouting materials cannot balance their working performance and insulation performance in high-temperature environments. In response to the above issues, this article uses red mud to prepare high ground temperature red mud based grouting materials (RMGS), and conducts tests on the working performance (viscosity, setting time, compressive strength) and insulation performance (thermal conductivity, specific heat capacity) of grouting materials at different temperatures (20, 40, 60, and 80 ℃), and analyzes the variation patterns and micro mechanisms of various characteristics with temperature. The results indicate that an increase in temperature will accelerate the viscosity development and condensation of the grouting material, and lead to a decrease in thermal conductivity and specific heat capacity. In addition, an appropriate temperature can also improve the compressive strength of the material. The increase in temperature will accelerate the hydration reaction rate of the grouting material and the development of internal pores, which is the reason why temperature affects the performance of the grouting material. In engineering applications, cement slurry is suitable for static water grouting, cement-sodium silicate slurry is suitable for dynamic water grouting, and RMGS is suitable for high-temperature tunnel grouting.

This study investigated the efficacy of carvone, abscisic acid (ABA), gibberellin (GA3), and variable temperature in managing dormancy and sprouting in aeroponically grown mini-tuber potato seeds. Results showed that carvone treatment effectively reduced weight loss rate by 12.25% and decay rate by 3.33% at day 25, compared to control. ABA treatment significantly enhanced germination rate to 97.33%. GA3 treatment resulted in the longest sprouts of 14.24 mm and reduced MDA content by 23.08% at day 30, indicating its potential in shortening dormancy and maintaining membrane integrity. Variable temperature treatment showcased a balanced performance in reducing weight loss and maintaining a lower relative conductivity, indicating less cellular damage. Enzymatic activities of α-amylase, CAT, and SOD were modulated by the treatments, ensuring a balanced enzymatic environment for seed vitality. These findings provide a robust foundation for refining post-harvest management strategies to optimize germination uniformity and preserve the quality of aeroponic potato seeds during extended dormancy, promising enhanced yield and productivity in potato cultivation.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

This study presents a comprehensive investigation of the formation, composition, and behaviour of oxide layers during the high-temperature oxidation of four different steel alloys (16Mo3, 13Cr, T24 and P91) at a uniform temperature of 650 °C. The research combines CALPHAD (CALculation of PHAse Diagrams) calculations, thermogravimetric analysis (TGA) and advanced microscopy techniques, including scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), to elucidate the complex mechanisms controlling oxidation kinetics and oxide layer development. CALPHAD calculations were used to determine the thermodynamically stable phases for each steel type at 650 °C. The results showed different phase compositions, highlighting the importance of steel composition in the formation of oxide layers. Each steel grade exhibited different kinetics, with 16Mo3 steel showing the highest oxidation rate, followed by 13Cr, T24 and P91. This variability highlights the role of steel composition, particularly chromium content, in determining oxidation behaviour. These results have significant implications for temporary overheating in industrial applications and contribute to a deeper understanding of oxidation processes in steels.

Pressure-sensitive paint (PSP) has received significant attention for capturing surface pressure in recent years. One major source of uncertainty in PSP measurements, temperature dependency, stems from the fundamental photophysical process that allows PSP to extract pressure information. The motion-capturing PSP method, which involves two luminophores, is introduced as a method to reduce the measurement uncertainty due to temperature dependency. A theoretical model for the pressure uncertainty due to temperature dependency is proposed and demonstrated using a static pressure measurement with an applied temperature gradient. The experimental validation of the proposed model shows that the motion-capturing PSP method reduces the temperature dependency by 37.7% compared to the conventional PSP method. The proposed model also proves that a PSP with zero temperature dependency is theoretically possible.

Panama possesses multiple wetlands designated as protected areas and zones of internationally recognized importance, one amongst them, the Bahía de Panamá wetland Ramsar site, which represents approximately 21% of the national mangrove surface coverage. Due to the major ecological and economic relevance of mangrove ecosystems and their vulnerability to the effects of a changing climate it is considered necessary to perform in situ studies that evaluate the changes in sensitive meteorological parameters. This research was carried out with the objective of measuring air temperature and relative humidity values in a section of the Panama Bay wetland for the 2017-2018 period. This section, neighboring urban development projects, houses since the year 2015 the first tower for determining eddy covariance and measuring micrometeorological parameters in mangrove forests in Panama. We determined monthly and yearly mean values for the studied variables and determined the correlation between them with the use of Pearson’s correlation coefficient. Results show that both parameters still remain at tolerable levels for this type of ecosystems, with both years having very similar annual mean temperatures (27.47 ± 0.32°C for 2017 and 27.48 ± 0.67°C for 2018) and the annual mean relative humidity for 2018, being 85.35%.

Fibre reinforced concrete (FRC) has been used for decades in certain applications of the construction industry, such as tunnel linings and precast elements, but has experienced an important progress in recent times, boosted by the inclusion of guidelines for their use in some national and international standards. Traditional steel fibres have been studied in depth and their performance is well known although in recent years new materials have been proposed as possible alternatives. Polyolefin macro-fibres, for instance, have proven to enhance the mechanical properties of concrete and the parameters that define their behaviour (fibre length, fibre proportion or casting method, for instance) have been identified. These fibres overcome certain traditional problems related to steel fibres, such as corrosion or their interaction with magnetic fields, which can limit the use of steel in some applications. The behaviour of polyolefin fibre reinforce concrete (PFRC) has been numerically reproduced with success through an embedded cohesive crack formulation that uses a trilinear softening diagram to describe the fracture behaviour of the material. Furthermore, concrete behaves well under high temperatures or fire events, especially when it is compared with other construction materials, but the behaviour of PFRC must be analysed if the use of these fibres is to be extended. To this end, the degradation of PFRC fracture properties has been recently experimentally analysed under a temperature range between 20ºC and 200ºC. As temperature increases, polyolefin fibres modify their mechanical properties and their shape, which reduce their performance as reinforcement of concrete. In this work, those experimental results, which include results of low (3 kg/m3) and high (10 kg/m3) proportion PFRC specimens, are used as reference to study the fracture behaviour of PFRC exposed to high temperatures from a numerical point of view. The experimental load-deflection diagrams are reproduced by modifying the trilinear diagram used in the cohesive model, which helps to understand how the trilinear diagram parameters are affected by high temperature exposure. Finally, some expressions are proposed to adapt the initial trilinear diagram (obtained with specimens not exposed to high temperature) in order to numerically reproduce the fracture behaviour of PFRC affected by high temperature exposure.

We consider an $N$ fermion system at low temperature $T$ in which we encounter special particle number values $N_m$ exhibiting special traits. These values arise in focusing attention upon the degree of mixture (DM) of the pertinent quantum states. Given the coupling constant of the Hamiltonian, the DMs stay constant for all $N$-values, but experience sudden jumps at the $N_m$. For a quantum state described by the matrix $\rho$, its purity is expressed by $Tr \rho^2$ and then the degree of mixture is given by $1 - Tr \rho^2$, a quantity that coincides with the entropy $S_q$ for $q=2$. Thus, Tsallis entropy of index two faithfully represents the degree of mixing of a state, that is, it measures the extent to which the state departs from maximal purity . Macroscopic manifestations of the degree of mixing can be observed through various physical quantities. Our present study is closely related to properties of many-fermion systemsn that are usually manipulated at zero temperature. Here we wish to study the subject at finite temperature. Gibbs' ensemble is appealed to. Some interesting insights are thereby gained.

Nickel base superalloy GH4169 is a material with strong mechanical properties and is difficult to process. In order to reduce tool wear during material processing and improve workpiece surface processing quality, based on the finite element simulation software DEFORM, the influence of n, ap, and fz parameters on tool wear during carbide tool milling GH4169 was studied, and a simulation orthogonal experimental model was established, The prediction model of tool wear is obtained; The ultrasonic vibration milling is compared with ordinary milling, and the improvement degree of different coating materials on carbide tool wear is explored. The results show that the ultrasonic vibration signal is helpful to reduce tool wear, improve the surface quality of the workpiece, and improve the stability of the milling process. TIALN/TIN (WC) composite coated tools have good cutting performance, help to reduce tool temperature, reduce tool wear, and improve tool life.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

Low-temperature accumulation is one of the essential stages in the growth process of woody ornamental plants. In this study, two different low-temperature treatments, 6℃ and 10℃, were used to analyze the effects of different low-temperature treatments on dormancy release and flowering of the 'Gulihong' plant using artificial low temperatures. Based on the experimental results, four typical early-blooming Prunus mume cultivars widely planted in Yangling area of Henan Province, China, including 'Zaoyudie', 'Zaohualve', 'Nanjing gongfen', and 'Gulihong', were selected as the experimental materials. The effects of low-temperature accumulation on the flowering characteristics of different cultivars were analyzed using a 6℃ artificial low-temperature treatment. The suitable cultivation temperature for early-blooming P. mume cultivars was screened to provide a theoretical basis for further exploration of P. mume bonsai cultivation techniques. The results showed that the flowering rate, flower diameter, flowering quantity, flowering uniformity, and bud development in the 6℃ treatment were significantly better than those in the 10℃ treatment. The flowering rate and quality of different cultivars gradually increased with the accumulation of low-temperature. Therefore, chill accumulation plays a significant role in promoting flowering quality.

Increasing wind speed alleviates physiological heat strain, however, health policies have advised against using ventilators or fans under heat wave conditions with air temperatures above the typical skin temperature of 35 °C. Recent research, mostly with sedentary participants, suggests mitigating effects of wind at even higher temperatures depending on the humidity level. Our study aimed at exploring and quantifying, whether such results are transferable to moderate exercise levels, and whether the Universal Thermal Climate Index UTCI reproduces those effects. We measured heart rates, core and skin temperatures and sweat rates in 198 laboratory experiments completed by five young, semi-nude, heat-acclimated, moderately exercising males walking the treadmill with 4 km/h on the level for three hours under widely varying temperature-humidity combinations and two wind conditions. We quantified the cooling effect of increasing wind speed from 0.3 to 2 m/s by fitting generalized additive models predicting the physiological heat stress responses depending on ambient temperature, humidity and wind speed. We then compared the observed wind effects to the assessment performed by UTCI. Increasing wind speed lowered physiological heat strain for air temperatures below 35 °C, but also for higher temperatures with humidity levels above 2 kPa water vapour pressure concerning heart rate and core temperature, and 3 kPa concerning skin temperature and sweat rate, respectively. UTCI assessment of wind effects correlated positively with the observed changes in physiological responses, showing the closest agreement (r=0.9) for skin temperature and sweat rate, where wind is known for elevating the relevant convective and evaporative heat transfer. These results demonstrate the potential of UTCI for adequately assessing sustainable strategies for heat stress mitigation involving fans or ventilators depending on temperature and humidity for moderately exercising individuals.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

(1) Background: This paper investigates the epidemiological risk related to temperature before and during COVID-19 in Italy; (2) Methods: Deaths in 2015-2019 and temperatures were correlated. Excess and COVID-19 deaths were examined to estimate the relationships with temperatures; (3) Results: Annual deaths were higher during the cold months (+45,000, SD = 4,700, S = 21). The scenario worsened during COVID-19. Mortality was higher during minimum temperature periods, although the curve moderately rose in the warmest months (r = -0.75, 95% CI = [-0.87; -0.56], S = 23). COVID-19 deaths showed a decreasing seasonality. Monthly excess deaths during COVID-19 were high (+4,200, IQR = [2,800; 8,000], S = 28) with a doubt of seasonality. COVID-19 mortality was correlated with regional latitude (r = 0.86, 95% CI = [0.68; 0.94], S = 20). Discrepancies between COVID-19 and excess deaths were found. The exposed population was subject to aging; (4) Conclusions: The epidemiological risk in Italy is seasonal and geographically dependent. Low and very high temperatures can lead to mortality peaks. Therefore, COVID-19 and any other epidemiological risk must be evaluated in light of this evidence. Health systems need to be strengthened during cold and extremely hot periods. Future research should investigate these phenomena at the causal level.

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.

Global warming has been increasing heat stress threat in animals which can be monitored by Temperature Humidity Index (THI). The present study describes the relationship of THI, calculated using 35 years period weather station data, and production performances of dairy cattle in a se-lected area of Bangladesh. The month January and June were identified as the coolest and hottest, respectively. Based on this outcome, every year in the month of January and June production performances of 10 crossbred cows with homogenous characteristics were monitored for a period of 5 years. The average THIMEAN value was found 17% higher in June as compared to January, and with this increment of THIMEAN average milk production was decreased 24.4% (p<0.05). The milk fat and protein content were also reduced (p<0.05) by 14.5 and 15.2%, respectively suggesting negative correlation as like as milk production. However, ash content was increased 15.3% that indicates a positive correlation. In addition, multiple regression analysis revealed each point increase in THIMEAN and rectal temperature, there was a decrease in milk yield 0.04 and 1.17 kg ECM, respectively. In contrary, each point increase in THIMEAN resulted 0.059 C increase of rectal temperature. Taken together, THIMEAN value calculated using metrological station data has distinct relationship with the production performances of lactating crossbred dairy cows.

Silver iodide (AgI) is a system prototype allowing the flow of ions through its structure and has a phase transition at 420 K, characterized by an abrupt change in conductivity and a high ionic conductivity. Introducing low concentrations of graphite (C) into the AgI structure produces a new material with a mixed conductivity (ionic and electronic) which increases with increasing temperature. The experimental results of the logarithm of the ionic conductivity as a function of the inverse of temperature for the (AgI)x–C(1−x) system for low carbon concentrations 0.97 ≤ x ≤ 0.99 were well fitted using a phenomenological model with a probability distribution for the charge carriers based on the carrier density

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

The urban heat island (UHI) is mostly due to urbanization. This phenomenon in concert with the high temperatures caused by global climate change may profoundly affect human thermal comfort, which can influence human productivity and morbidity especially in spring/summer period. The main objective of this investigation was to determine changes in degree of thermal comfort of Mexico City’s inhabitants and compare it with the physiological equivalent temperature (PET) to evaluate whether PET and its categorization are adequate to be applied in Mexico City. A series of microclimatological measurements to estimate PET were made in four sites including the city´s center. Concomitantly, a series of surveys of thermal perception were applied to 1300 passersby. The results show that PET has increased from 1990 to 2020 from 0.1208 °C/year to 0.1498 °C/year in the study sites, besides overestimating the degree of thermal comfort of people according to the stablished categories or classes. It is concluded that it is necessary to adjust thermal stress categories. Knowing the percentage of people without thermal comfort will lead us to determine different ranges in environmental parameters to define an acceptable environment for most people.

An increase in air temperature leads to a significant transformation of the relief and landscapes of the Arctic. The rate of permafrost degradation, posing a profound change in the Arctic landscape, depends on air temperature, vegetation cover, type of soils, surface and ground waters. The existing international circumpolar programs dedicated to monitoring the temperature state of permafrost TSP (Thermal State Permafrost) and active layer thickness CALM (Circumpolar Active Layer Monitoring) are not sufficient for a comprehensive characterization of geocryological conditions. Yet, no standardized protocol exists for permafrost monitoring and related processes. Here, we propose a novel multi-parameter monitoring protocol and implement for two sites in the European part of the Russian Arctic: the Yary site along the coast of the Baydaratskaya Bay in the Kara Sea (68.9°N) within the continuous permafrost area and the Hanovey site in the Komi Re-public (67.3°N) within the discontinuous permafrost one. The protocol includes drilling boreholes, determining the composition and properties (vegetation cover and soils), snow cover measure-ment, geophysical imaging, active layer estimation and continuous ground temperature meas-urements. Ground temperature measured in 2014 – 2020 revealed that amplitudes of surface tem-perature fluctuation had no significant difference between the Yary and Hanovey sites, while that the mean annual temperatures between the areas had a considerable difference of greater than 3.0 °C. The period of the presence of the active layer changed with the year (e.g., ranging between 135 and 174 days in the Yary site), showing longer when the air temperatures in summer and the preceding winter were higher. Electrical resistivity tomography (ERT) allowed determining the permafrost distribution and active layer thicknesses. Thermometry results were consistent with our geophysical data. Analyzing the composition and properties of frozen soils helped better interpret the data of geophysical and temperature measurements. Our work by integrating the study of the soil properties, ground temperatures, and ERT allowed fully characterize these sites, suggesting that it helps better understand the thermal state in any other research sites in the European north of Russia. Our suggested monitoring protocol enables calibrating and verifying the numerical and analytical models of the heat transfer through the earth’s surface.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

Mangrove vegetation plays a vital role in habitat and nursing ground for different organisms and prevents coastal erosion caused by wave and tide action. In recent years the mangrove vegetation in Chattogram coast, Bangladesh, has been interrupted by other infrastructural development, which has a destructing effect on the surrounding environment. Land surface temperature analysis of an area helps learn about different environmental conditions, weather, and climate. It is also essential to monitor the rising temperature and global warming, the biggest threat to humanity. NDBI and NDVI are the efficient process for monitoring vegetation and build up areas of a geographical location. This study focused on those analyses to understand the importance of mangrove vegetation in the Salimpur area and surrounding coastal areas of Chattogram by studying the relationship between NDVI and NDBI, NDVI and LST, NDBI, and LST. The outcome indicates that a higher vegetation index results in lower land surface temperature during different periods, negatively correlated. This study also found a strong positive correlation between buildup index (NDBI) and land surface temperature (LST), which means Land Surface temperature was found higher in Buildup areas. The vegetation areas are greatly affected by the buildup areas. The correlation between buildup areas and vegetation areas was strongly negative, which means an increase of NDBI decreases NDVI, and a decrease of NDBI increases NDVI.

Recently, it was reported that the physical cross-linking exhibited by some biopolymers could provide multiple benefits to biomedical applications. In particular, grafting thermoresponsive polymers onto biopolymers may enhance the degradability or offer other features, as ther-mothickening behavior. Thus, different interactions will affect the different hydrogen bonds and interactions from the physical cross-linking of CMC, the lower critical solution temperatures (LCSTs), and the presence of the ions. This work focuses on the study of blends composed of poly(N-isopropylacrylamide), poly(N-ethylacrylamide), and carboxymethyl cellulose in water and water/methanol. The molecular features, the thermoresponsive behavior, and gelation phenomena are deeply studied. The ratio defined by both homopolymers will alter the final properties and the gelation of the final structures, showing that the presence of the hydrophilic groups modifies the number and contributions of the diverse hydrogen bonds.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

While the ongoing climate change is well documented, the impacts exhibit a substantial variability, both in direction and magnitude, visible even at regional and local scales. However, the knowledge of regional impacts is crucial for the design of mitigation and adaptation measures, particularly when changes in the hydrological cycle are concerned. In this paper we present hydro-meteorological trends based on observations from a hydrological research basin in Eastern Austria between 1979-2019. The analysed state variables include the air temperature, the precipitation, and the catchment runoff. Additionally, trends for the catchment evapotranspiration were derived. The analysis shows that while the mean annual temperature was decreasing and annual temperature minima remained constant, the annual maxima were rising. The long-term trends indicate a shift of precipitation to the summer with minor variations observed for the remaining seasons and at an annual scale. Observed precipitation intensities mainly increased in spring and summer between 1979-2019. The catchment evapotranspiration, computed based on catchment precipitation and outflow, showed an increasing trend for the observed time period.

Lack of due attention to the orientation of streets and establishment of urban blocks without regard for climatic characteristics and conditions of the environment have an adverse effect on thermal comfort in open urban spaces. Construction of new settlements without taking into account climatic requirements undermines thermal comfort for pedestrians and other users, especially in cold regions. Considering the coldness of the region under study and the significance of the orientation of streets in absorbing radiation and providing heat to outdoor urban spaces, this study investigates the effect of the orientation of streets on microclimatic comfort in one of the residential towns of Hamadan City in Iran. For this purpose, microclimate simulation was performed using ENVI-met software. A residential block with four different orientations (the most common orientations of its surrounding buildings) were simulated in the coldest day of winter and the hottest day of summer. The results suggest that streets have different thermal behavior in different orientations. Orientation affects mean radiant temperature (Tmrt), the duration of exposure to direct sunlight, wind speed, and physiological equivalent temperature (PET), which are all important factors in thermal comfort. Based on these findings, north-south streets in Hamedan receive more radiant temperature during winter compared to other simulated orientations and provide more desirable thermal comfort. The average PET value on a winter day at a point on the north-south passage was 4.5-8 °C warmer than other orientations. In summer, streets with intercardinal orientations (i.e., northeast-southwest and northwest-southeast) provided the lowest PET (about 2 °C cooler than other orientations) and better thermal comfort

High temperature (HT) significantly affects the crop physiological traits and reduces the 12 productivity in plants. To increase yields as well as survival of crops under HT, developing heat13 tolerant plants is one of the main targets in crop breeding programs. The present study attempted 14 to investigate the linkage of the heat tolerance between the seedling and the reproductive growth 15 stages of tomato cultivars ’Dafnis‘ and ’Minichal’. This research was undertaken to evaluate heat 16 tolerance under two experimental designs such as screening at seedling stage and screening from 17 reproductive traits in greenhouses. Survival rate and physiological responses in seedlings of 18 tomatoes with 4-5 true leaf were estimated under HT (40 °C, RH 70%, day/night, respectively) and 19 under two control and HT greenhouse conditions (day time 28 °C and 40 °C, respectively). Heat 20 stress significantly affected physiological-chemical (photosynthesis, electrolyte conductivity, 21 proline) and vegetative parameters (plant height, shoot fresh weight, root fresh weight) in all 22 tomatoes seedlings. The finding revealed that regardless of tomato cultivars the photosynthesis, 23 chlorophyll, total proline and electrical conductivity parameters were varied in seedlings during the 24 heat stress period. The heat tolerance rate of tomatoes in the seedling stage might not be associated 25 always with reproductive parameters. HT reduced the fruit parameters likeas fruit weight (31.9%), 26 fruit length (14.1%), fruit diameter (19.1%) and fruit hardness (9.1%) in compared to NT under HT 27 in heat susceptible tomato cultivar ‘Dafnis’, while in heat tolerant cultivar ‘Minichal’ fruit length 28 (7.1%) and fruit diameter (12.1%) was decreased by the affect of HT but on the contrary fruit weight 29 (3.6%) and fruit hardness (8.3%) were increased. In conclusion, screening and selection for tomatoes 30 should be evaluated at the vegetative and reproductive stages with consideration of reproductive 31 parameters.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

The use of different primary energy sources in human society has led to two major polluting emissions in the environment: energy (mostly heat), and chemical substances (mostly carbon dioxide). In this paper, the total global anthropogenic emissions of heat to the atmosphere during the industrial era (years 1850-2018) were determined and their effect on the change of global atmospheric temperature was calculated. The concept of a theoretical three-phase Earth reactor was introduced to estimate global atmospheric temperature increase caused by anthro-pogenic heat emissions. The resulting calculations closely approximated the actual atmospheric temperature change recorded during the last 170-year period. These results suggest that the temperature change of the atmosphere (global warming) is entirely due to anthropogenic heat emissions.

The efficacy of weed management depends on the correct control timing according to the seedling emergence dynamics. Since soil temperature and soil moisture are two main factors that determine weed germination, the hydrothermal time model can be used to predict their emergence. The aim of this study was to estimate the base temperature (Tb) and base water potential (Ψb) for germination of Chenopodium album, Amaranthus retroflexus, Setaria pumila and Panicum capillare collected from fields in continental Croatia and then to compare these values with those of Italian populations embedded in the AlertInf model. Germination tests were performed at seven constant temperatures (ranging from 4 to 27°C) and eight water potentials (0.00 to - 1.00 MPa). Estimated Tb and Ψb were 3.4°C, -1.38 MPa for C. album, 13.9°C, -0.36 MPa for A. retroflexus, 6.6°C, -0.71 MPa for S. pumila and 11.0°C, -0.87 MPa for P. capillare, respectively. According to the criterion of overlap of the 95% confidence intervals, only Tb of C. album, and Ψb of A. retroflexus were similar between Croatian and Italian populations. Further field experiments should be conducted in the Croatian field to monitor weed emergence patterns of C. album and to calibrate the AlerInf equation parameters.

When different strain hardening and strain rate sensitive materials are used for scaled model and prototype, the traditional pure geometrical similarity laws of solid mechanics will fail. Although correcting the basic scaling factors of velocity, density and geometry have been developed to compensate for the material distortion in recent non-geometric scaling works, it is difficult to be widely used because of its inherent indirect (depending on the structural strain and strain rate responses) and inexact (having significant prediction errors for prototype) defects. In this paper, a framework of material similarity, based on the new suggested material dimensionless numbers and the ‘Material number vs. strain/strain-rate’ function curves, are further developed, which represents the objective requirement of similarity theory for the basic mechanical properties of materials. It is demonstrated what is similitude materials of solid mechanics and how to use the best similitude materials to overcome the non-scalabilities of materials for identical or different materials. The direct and exact solution of the basic correction factors is further obtained and therefore overcomes the previous inherent indirect and inexact defects radically. Based on the similarity evaluation of different materials of the classical constitutive models, the impacted structures of circular plate and crooked plate with strain hardening and strain rate sensitive materials are verified numerically. The results show the completely different materials can be exact similitude for various structural behaviors (strain, strain rate, stress and displacement) of time and space fields after using the best similitude materials; and the basic correction factors do not depend on the structural strain and strain rate responses. As a contrast, when the non-similitude materials are used, the similarity results are very sensitive to the selection of strain/strain-rate and often leads to failed predictions. In addition, for the material elastic and temperature effects, the proposed method is also discussed to be valid.

The present study investigated the effect of different ambient temperature and relative humidity (RH) but equal temperature-humidity index (THI) on laying performance, egg quality, heterophil to lymphocyte ratio (H/L ratio), corticosterone (CORT) concentration in blood, yolk and albumen, and plasma biochemical parameters in laying hens. One hundred and twenty commercial hens (Hy-Line Brown) aged 60 weeks were allocated into 2 environmental chambers. Laying hens were subjected to either one of two thermal treatments, i.e., 26ºC and 70% RH (LH75) and 30ºC and 30% RH (HL75) for 28 days. Both thermal treatments had equal THI being 75. Neither LH75 nor HL75 affected (P > 0.05) laying performance including egg production, egg weight, egg mass, feed intake, and feed conversion ratio. Plasma biochemical parameters such as total cholesterol, high-density lipoprotein cholesterol, triglyceride, calcium, magnesium, and phosphorus was not altered (P > 0.05) by thermal treatments. As to the stress indicators, both environment regimes failed (P > 0.05) to affect blood H/L ratio and CORT levels in plasma, yolk and albumen although albumen CORT levels were elevated (P < 0.05) in LH75 vs. HL75 at days 3, 7, and 28. In conclusion, our study suggests that laying hens performed and responded equally when they were exposed to equal THI environment conditioned from either 26ºC and 70% RH or 30ºC and 30% RH. The results of this study will be served as a scientific basis for management decisions and handling under thermally challenging conditions.

It is common knowledge that increasing CO₂ concentration plays a major role in enhancement of the greenhouse effect and contributes to global warming. The purpose of this study is to complement the conventional and established theory that increased CO₂ concentration due to human emissions causes an increase of temperature, by considering the reverse causality. Since increased temperature causes an increase in CO₂ concentration, the relationship of atmospheric CO₂ and temperature may qualify as belonging to the category of “hen-or-egg” problems, where it is not always clear which of two interrelated events is the cause and which the effect. We examine the relationship of global temperature and atmospheric carbon dioxide concentration at the monthly time step, covering the time interval 1980–2019, in which reliable instrumental measurements are available. While both causality directions exist, the results of our study support the hypothesis that the dominant direction is T → CO₂. Changes in CO₂ follow changes in T by about six months on a monthly scale, or about one year on an annual scale. We attempt to interpret this mechanism by involving biochemical reactions, as at higher temperatures soil respiration, and hence CO₂ emission, are increasing.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

We investigated the characteristics of surface wind speeds and temperatures predicted by the local data assimilation and prediction system (LDAPS) operated by the Korean Meteorological Administration. First, we classified automated weather stations (AWSs) into four categories [urban flat (Uf), rural flat (Rf), rural mountainous (Rm), and rural coastal (Rc) terrains] based on the surrounding land cover and topography, and selected 25 AWSs representing each category. Then we calculated the mean bias error of wind speed (WE) and temperature (TE) using AWS observations and LDAPS predictions for the 25 AWSs in each category for a period of 1 year (January–December 2015). We found that LDAPS overestimated wind speed (average WE = 1.26 m s–1) and underestimated temperature (average TE = –0.63°C) at Uf AWSs located on flat terrain in urban areas because it failed to reflect the drag and local heating caused by buildings. At Rf, located on flat terrain in rural areas, LDAPS showed the best performance in predicting surface wind speed and temperature (average WE = 0.42 m s–1, average TE = 0.12°C). In mountainous rural terrain (Rm), WE and TE were strongly correlated with differences between LDAPS and actual altitude. LDAPS underestimated (overestimated) wind speed (temperature) for LDAPS altitudes that were lower than actual altitude, and vice versa. In rural coastal terrain (Rc), LDAPS temperature predictions depended on whether the grid was on land or sea, whereas wind speed did not depend on grid location. LDAPS underestimated temperature at grid points on the sea, with smaller TE obtained for grid points on sea than on land.

Ti-6Al-4V (TC4) titanium alloy parts were successfully fabricated by laser melting deposition (LMD)technology in this study. Proper normalizing temperatures were presented in detailed for bulk LMD specimens. Optical microscope, scanning electron microscopy, X-ray diffraction and electronic universal testing machine were used to characterize the microstructures, phase compositions, the tensile properties and hardness of the TC4 alloy parts treated using different normalizing temperature. The experimental results showed that the as-fabricated LMD speceimens microstructures mainly consisted of α-Ti phase with a small amount of β-Ti phase. After normalizing treatment, in the area of α-Ti phase, the recrystallized length and width of α-Ti phase both increased. When normalizing in the (α+β) phase field, the elongated primary α-Ti phase in the as-deposited state was truncated due to the precipitation of β-Ti phase and became a short rod-like primary α-Ti phase. In as-fabricated microstructure, the β-Ti phase was precipitated between different short rod-shaped α-Ti phases distributed as basketweave. After normalizing treatment at 990 for two hours with subsequent air cooling, the TC4 titanium alloy had significant different microstructures from original sample produced by LMD. Moreover, the mismatch of tensile and hardness property was mitigated in this heat treatment. So the normalizing treatment methods and temperature can be qualified as a prospective heat treatment of titanium alloy fabricating by laser melting deposition.

The physical environment plays an important role in the transmission of respiratory infections like Covid-19. To find relevant articles on environmental factors influencing respiratory infection outbreaks, we searched Pub med Central on the following topics: 1. Environmental pollution causing coronavirus fatality- 73 results, relevant 1 article, 2. Environmental factors affecting Covid-19, 149 results from which there were 6 relevant articles, 3. Impact of air pollution on Covid-19 fatality, 10 results, relevant 3 articles, 4. Environmental factors affecting respiratory viruses- 10646 results were obtained, 2 relevant articles. We searched Google scholar on environmental factors affecting Covid-19 transmission and found 7 relevant papers. We excluded the duplicates in each of the key words search. Date of search was on 20^th April 2020. All articles included in results were scrutinized and relevance of articles was based on their content that discussed meteorological and physical environment factors in the spread and severity of Covid-19. We have discussed factors like air pollution, smoking, air temperature, humidity and air velocity as contributing factors. If meteorological factors are conducive to spread in a particular area, we need protective measures way before a respiratory infection outbreak occurs. Covid-19 is a lesson learnt the hard way, and we must enable people to practice hygienic practices with limited resources but high level of protection that it provides. Air pollution control can prevent priming of respiratory system which shall further protect from pulmonary infections.

Estimating heat emission losses of heating systems is an important task of energy efficiency assessments in buildings. To this aim, the present international standards contain tabulated values for different emitter and control system configurations, without however explaining how to compute the effect of increased setpoint temperatures on the system losses. Moreover, the effects of each component are treated as independent, while e.g. vertical stratification and temperature control of the system are cross-related. In this paper we attempt to fill this gap by proposing a calculation method to calculate the product category specific setpoint variations for space heating emitters, accounting for the overall heat balance in the enclosure and including the cross-correlations of each component as well. The emission losses of a heating system are computed using a temperature setpoint variation method that is imposed on annual energy calculations. This complements the procedure presented in the Standard EN15316-2, also providing the possibility to use product-specific values of setpoint variations instead of tabulated values. As the main finding of the study, the calculation process is defined for a European Reference Room, namely for a specific enclosure that allows an accurate and transparent evaluation of the total setpoint variation. The product-specific values of setpoint variations are calculated from measured vertical stratification and control parameters with an annual simulation model of the European Reference Room. The total setpoint variations were simulated for a set of heat emitters and controllers in order to quantify and compare the energy performance of a new and an old type building located in Strasbourg. We find that the total setpoint variation required to overcome emission losses is up to 2.00 °C in the old building and 1.20 °C in the new building, corresponding respectively to an increase in total heating energy usage of up to 22% and 20%.

The improvement of the methane combustion activity was observed in cyclic temperature-programmed and isothermal reactions over Pd/ZrO2 catalysts by simple reduction/re-oxidation treatment. The catalytic activity increased during the initial stages of isothermal reaction, and the light-off temperature was lowered as the number of cycles increased in the cyclic temperature-programmed reaction. To reveal the origin of activation, variations in the reduction properties after the activation period were carefully investigated through CH4 temperature-programmed reduction (TPR) measurements. From the CH4-TPR results, it was confirmed that the reduction temperature decreased significantly after activation. The observation of the CH4-TPR peak at relatively low temperatures is directly proportional to the catalytic activity of CH4 combustion. It was therefore concluded that repeated reduction/re-oxidation occurred in the reactant stream, and this phenomenon allowed the combustion reaction to proceed more easily at lower temperatures.

Dengue hemorrhagic fever is an arboviral infectious disease that has occurred frequently as an extraordinary event due to its fast spread and lethal potential in Indonesia. The vector Aedes aegypti is sensitive to climate variability. This study determines the relationship between climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia from 2009 to 2017. This study used the monthly dengue hemorrhagic fever incidence obtained from the Surabaya Health Office and the monthly climate variability parameters (average temperature, rainfall, humidity) obtained from the Indonesian Agency for Meteorology, Climatology and Geophysics and website www.worldweatheronline.com. Data analysis was done using One-Sample Kolmogorov Smirnov Test and Spearman non-parametric correlation test. The results showed a correlation between all three climate variability parameters with dengue hemorrhagic fever incidence (average temperature p<0.05, r=-0.603; rainfall p<0.05, r=0.407; humidity p<0.05, r=0.7). Average temperature is negatively correlated to dengue hemorrhagic fever incidence, while rainfall and humidity are positively correlated to dengue hemorrhagic fever incidence. This study shows preliminary evidence on the correlation of climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia.

The water-rich liquid layer immobilized on the surface of the polar stationary phases is critical to the retention of polar compounds in hydrophilic interaction chromatography (HILIC). Although the presence of the adsorbed water layer has been investigated and confirmed by multiple techniques, there is a lack of quantitative measure that can be easily determined and linked to chromatographic parameters. This study proposes a simple measure termed volume ratio (the ratio of the adsorbed water layer volume and the mobile phase volume) that provides a relative, but quantitative information on the adsorbed water layer and may be linked to the phase ratio. The volume ratio can be easily determined using toluene elution volume. The volume ratio values are measured in 25 polar stationary phases in various mobile phase conditions. In addition to the acetonitrile content in the mobile phase, ammonium acetate concentration in the mobile phase and column temperature also have significant influences on the volume ratio and the adsorbed water layer.

There is increasing use of wood-based composites in industry not only because of the shortage of solid wood, but above all for their better properties such as: strength, aesthetic appearance, etc. compared to wood. Medium density fibreboard (MDF) is a wood-based composite that is widely used in the furniture industry. The goal of the research conducted was to determine the effect of the type of coating on the drill cutting blades on the value of thrust force (F_t), cutting torque (M_c), cutting tool temperature (T) and surface roughness of the hole in drilling MDF panels. In the tests three types of carbide drills (HW) were used: not coated, TiAlN coated and ZrN coated. The measurement of both the thrust force and the cutting torque was carried out using an industrial piezoelectric sensor. The temperature of the cutting tool in the drilling process was measured using an industrial temperature measurement system using a K-type thermocouple. It was found that the value of the maximum temperature of the tool in the drilling process depends not only on the cutting speed and feed rate, but also on the type of coating of the cutting tool. The value of both the cutting torque and the thrust force is significantly influenced by the value of the feed rate and the type of drill coating. The effect of varying plate density on the surface roughness of the hole and the variation of the value of the thrust force is also discussed. The results of the investigations were statistically analysed using a multi-factorial analysis of variance (ANOVA).

Dengue hemorrhagic fever is an arboviral infectious disease that has occurred frequently as an extraordinary event due to its fast spread and lethal potential in Indonesia. The vector Aedes aegypti is sensitive to climate variability. This study determines the relationship between climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia from 2009 to 2017. This study used the monthly dengue hemorrhagic fever incidence obtained from the Surabaya Health Office and the monthly climate variability parameters (average temperature, rainfall, humidity) obtained from the Indonesian Agency for Meteorology, Climatology and Geophysics and website www.worldweatheronline.com. Data analysis was done using One-Sample Kolmogorov Smirnov Test and Spearman non-parametric correlation test. The results showed a correlation between all three climate variability parameters with dengue hemorrhagic fever incidence (average temperature p<0.05, r=-0.603; rainfall p<0.05, r=0.407; humidity p<0.05, r=0.7). Average temperature is negatively correlated to dengue hemorrhagic fever incidence, while rainfall and humidity are positively correlated to dengue hemorrhagic fever incidence. This study shows preliminary evidence on the correlation of climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia.

This study presents a novel approach for the early detection of developing thunderstorms. To date, methods for the detection of developing thunderstorms usually rely on accurate atmospheric motion vectors (AMVs) for the estimation of cooling rate of convective clouds, which corresponds to the updraft strength of the cloud objects. In this study we present a method for the estimation of the updraft strength that does not rely on AMVs. The updraft strength is derived directly from the satellite observations in the SEVIRI water vapor channels. For this purpose the absolute value of the vector product of two vectors derived from the observed radiances emitted by the water vapor channels in 2 subsequent satellite images is calculated. The x and y components of the vectors consists of the temporal change of the spatial brightness temperature gradients in x- and y-direction, the z component consists of the temporal variation of the brightness temperature at pixel level. The absolute value of the vector product is referred to as normalized updraft strength (NUS). The performance of the method has been investigated for 2 summer periods in 2016 and 2017 by validation with lightning data. Values of the Critical Success Index (CSI) of about 66 % for the 2016 period and 62 % for the 2017 period demonstrate the good performance of the method. The POD values for the experiments with the highest CSI values are 90.3 for 2016 period and 87.6 for the 2017 period, respectively The corresponding FAR values are 28.2% (2016) and 32.5 % (2017), respectively. In summary, the method has the potential to reduce the forecast lead time significantly, and can be quite useful in regions without a well maintained radar network.

The relationship between city size, coastal land use and air temperature rise with distance from coast during summer day is analyzed using the meso-scale Weather Research & Forecasting (WRF) model in five coastal cities in Japan with different sizes and coastal land use (Tokyo, Osaka, Nagoya, Hiroshima and Sendai) and inland cities in Germany (Berlin, Essen and Karlsruhe). Air temperature increased as distance from the coast increased, reached its maximum, and then decreased slightly. In Nagoya and Sendai, the number of urban land use in coastal areas is less than the other three cities, where air temperature is a little lower. As a result, air temperature difference between coastal and inland urban area is small and the curve of air temperature rise is smaller than those in Tokyo and Osaka. In Sendai, air temperature in the inland urban area is the same as in the other cities, but air temperature in the coastal urban area is a little lower than the other cities, due to about one degree lower sea surface temperature influenced by the latitude. In three German cities, the urban boundary layer may not develop sufficiently because the fetch distance is not enough.

Recently Kawashima has reported that, when wetted with alkanes, several forms of graphite and single-layer graphene exhibit superconductor-like properties above room temperature under ambient pressure [AIP Adv. 2013, 3, 052132; arXiv:1612.05294; arXiv:1801.09376]. Under the assumption that these seemingly unlikely properties arise from the presence of paired electrons brought about by the alkane-wetting, we explored their implications to arrive at a probable mechanism for strong electron-pairing driven by Fermi surface nesting and acoustic phonon. This mechanism explains why alkane-wetting is essential for the graphene systems to become “superconductor-like” above room temperature and why the “T_c” of alkane-wetted pitch-based graphite fibers increases almost linearly from ~363 to ~504 K with increasing the molecular weight of alkane from heptane to hexadecane. It also provides a number of experimentally-verifiable predictions, the confirmation of which will provide a strong support for the superconductivity driven by Fermi surface nesting and acoustic phonon.

Different process parameters can alter the temperature during machining. Consequently, selecting process parameters that lead to a desirable cutting temperature would help to increase the tool life, decrease the tensile residual stress, and controls the microstructure evolution of the workpiece. An inverse computational methodology is proposed to design the process parameters for specific cutting temperature. A physics-based analytical model is used to predict the temperature induced by cutting forces. To calculate the temperature induced by the deformation in the shear zone, a moving point heat source approach is used. The shear deformation and chip formation model is implemented to calculate machining forces as functions of process parameters, material properties, and etc. The proposed model uses the analytical model to predict the cutting temperatures and applies a variance-based recursive method to guide the inverse analysis. In order to achieve the cutting process parameters, an iterative gradient search is used to adaptively approach the specific temperature by the optimization of process parameters such that an inverse reasoning can be achieved. Experimental data are used to illustrate the implementation and validate the viability of the computational methodology.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

The accurate quantification of $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios for Mössbauer spectroscopic room temperature measurements involves many steps and, when shown in a composite Mössbaur data table, does not allow enough space for more Mössbauer parameters to be presented in the composite table. So a simple formula is derived, (presented as a short communication) which users will find helpful when they have to determine corrected $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios in their room temperature Mössbauer experiments.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

Despite the ecological importance of forest tree species, our study was motivated by scarce data on dendrochronology studies limited to the northwestern part of Tajikistan due to lack of access to such a part of the country which is difficult to access. Current studies on Junipers in the northwestern part of Tajikistan identified that tree ring-based climate reconstruction is possible. Cores of Juniperus Turkestanica from Taboshar area, Sogd province were developed into 176-year tree-ring width chronology. In the current study a summer (June-September) minimum temperature reconstruction spanning AD 1840–2016 was developed, which can explain 30.0% of the instrumental variableness for the period of 1940–2015. Five warmest (1856–1866, 1869–1871, 1907–1916, 1923–1935, 1988–2016) and four coldest time periods (1840–1855, 1872–1906, 1917–1922, 1940–1984) were identified. The developed reconstruction coincides with cold and warm periods with prior investigations from tree-rings in China, Mongolia, Kyrgyzstan, Kazakhstan and Tajikistan. Spatial correlation analysis with the gridded minimum temperature data shows that the temperature reconstruction covers geographical representation over High Asia. Significant correlation was found between temperature reconstruction with summer SST, which suggests strong linkages of regional temperature variability with Indian-Ocean climate system. The obtained spectral peaks from the spectral analysis of the summer temperature reconstruction were significantly at 84.7-year (90%), 2.9-year (99%), 2.6-year (99%), 2.5-year (99%), 2.4-year (99%) and 2.2-year (99%).