As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

An in-depth study of the failure of granular materials, which is known as a mechanism to generate defects, can reveal the facts about the origin of the imperfections such as cracks in the carbon anodes. The initiation and propagation of the cracks in the carbon anode, especially the horizontal cracks below the stub-holes, reduce the anode efficiency during the electrolysis process. In order to avoid the formation of cracks in the carbon anodes, the failure analysis of coke aggregates can be employed to determine the appropriate recipe and operating conditions. In this paper, it will be shown that a particular failure mode can be responsible for the crack generation in the carbon anodes. The second-order work criterion is employed to analyze the failure of the coke aggregate specimens and the relationships between the second-order work, the kinetic energy, and the instability of the granular material are investigated. In addition, the coke aggregates are modeled by exploiting the discrete element method (DEM) to reveal the micro-mechanical behavior of the dry coke aggregates during the compaction process. The optimal number of particles required for the failure analysis in the DEM simulations is determined. The effects of the confining pressure and the strain rate as two important compaction process parameters on the failure are studied. The results reveal that increasing the confining pressure enhances the probability of the diffusing mode of the failure in the specimen. On the other hand, the increase of strain rate augments the chance of the strain localization mode of the failure in the specimen.

Deformation behavior of MXene based polymer composites with bioinspired brick and mortar structures is analyzed. MXene/Polymer nanocomposites are modeled at microscale using bioinspired configurations of nacre-mimetic brick-and-mortar assembly structure. MXenes (brick) with polymer matrix (mortar) are modeled using classical analytical methods and numerical methods based on Finite Elements (FE). The analytical methods provide less accurate estimation of elastic properties compared to numerical one. MXene nanocomposite models analyzed with FE method provide estimates of elastic constants in the same order of magnitude as literature reported experimental results with good consistency. Bioinspired design of MXene nanocomposites results in the effective Young’s modulus of the nanocomposite increase by 25.1 % and the strength (maximum stress capacity within elastic limits) increase by 42.3 %. The brick and mortar structure of the nanocomposites leads to interlocking mechanism between MXene fillers in polymer matrix, resulting in effective load transfer, good strength, and damage resistance. This is demonstrated in this paper by numerical analysis of MXene nanocomposites subjected to quasi-static loads.

Production of electricity using hydro-kinetic tidal turbines has many challenges that must to be overcome to ensure reliable, economic and practical solutions. Energy from flowing water is converted by a system comprising: the turbine rotor blades, a gearbox, an electrical generator, control systems, power electronics, export cables, and a connection to the electricity grid. To date these have often been modelled using simulations of independent systems, lacking bi-directional, real-time, coupling. This approach leads to critical effects being missed. Turbulence in the flow, results in large velocity fluctuations around the blades, causing rapid variation in the shaft torque and generator speed, and consequently in the voltage seen by the power electronics and consequently the export power quality. The resulting poor quality power may be unacceptable to the grid. Conversely, grid frequency and voltage changes can also cause the generator speed to change, resulting in changes to the shaft speed and torque and consequently changes to the lift and drag forces acting on the blades. Clearly, fully integrated, bi-directional, models are needed. Here we present two fully coupled models which use different approaches to model the hydrodynamics of rotor blades. The first model uses Blade Element Momentum Theory (BEMT), resulting in an efficient tool for turbine designers. The second model also uses BEMT combines this with an actuator line model of the blades coupled to an unsteady computational fluid dynamics (CFD) simulation. This simulation, implemented in OpenFOAM, uses an energy balance to compute the shaft speed. Both the BEMT and CFD models are coupled to an Open Modellica model of the electro-mechanical system. Both models have been used to simulate the performance of a 1.2m diameter, scale model, of a three bladed horizontal axis tidal turbine tested in the University of Edinburgh FloWave Ocean Energy Research Facility. The turbulent flow around the blades and the mechanical-electrical variables during the stable period of operation are analysed. Time series and tabulated average values of mechanical thrust, power, torque, and rotational speed as well as electrical variables of generator power, electromagnetic torque, voltage and current are presented for the coupled system simulation. The relationship between the mechanical and electrical variables and the results from both tidal turbine approaches are discussed. Our comparison shows that while the BEMT model provides an effective design tool (leading to slightly more conservative designs), the CFD/BEMT simulations provide more accurate predictions of the blade loads which can be especially important in assessing fatigue on the blades (though at an increased computational cost).

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

One challenging problem is the representation of three-dimensional datasets that vary with time. These datasets can be though as a cloud of points that gradually deforms. But point-wise variations lack of information about the overall deformation pattern, and more importantly, about the extreme deformation locations inside the cloud. The present article applies a technique in computational mechanics to derive the strain-rate state of a time-dependent and three-dimensional data distribution, by which one can characterize its main trends of shift. Indeed, the tensorial analysis methodology is able to determine the global deformation rates in the entire dataset. With the use of this technique, one can characterize the significant fluctuations in a reduced multivariate description of an urban system and identify the possible causes of those changes: calculating the strain-rate state of a PCA-based multivariate description of an urban system, we are able to describe the clustering and divergence patterns between the districts of the city and to characterize the temporal rate in which those variations happen.

For many years, the programmable positioners have been widely applied in structures of modern electro-pneumatic final control elements. The positioner consists of an electro-pneumatic transducer, embedded controller and measuring instrumentation. Electro-pneumatic transducers that are used in positioners are characterized by a relatively short mean time-to-failure. The practical and economical method of a reasonable prolongation of this time is proposed in this paper. It is principally based on assessment and minimizing the effort of the embedded controller. For this purpose, were introduced: the control value variability, mean-time and the cumulative controller's effort. The diminishing of controller effort has significant practical repercussions, because it reduces the intensity of mechanical wear of the final control element components. On the other hand, the reduction of the cumulative effort is important in the context of process economy due to limitation of the consumption of energy of compressed air supplying the final control element. Therefore, the minimization of introduced effort factors has an impact on increasing the functional safety and economics of the controlled process. As a result of the performed simulations, the recommendations regarding the selection of the structure and tuning of positioner controller were elaborated. The simulations were performed in the Matlab-Simulink environment with the use of the liquid level control system in which a phenomenological model of a final control element was deployed. It has been proven that under appropriate conditions, it is possible to extend significantly the lifetime of the final control element and simultaneously enhance the control quality factors.

Cogging torque is a pulsating, parasitic and undesired torque ripple intrinsic of the design of a permanent magnet synchronous generator (PMSG), which should be minimized due to its adverse effects: vibration and noise. In addition, as aerodynamic power is low during start-up at low wind speeds in small wind energy systems, the cogging torque must be as low as possible to achieve a low cut-in speed. A novel mitigation technique using compound pre-slotting, based on a combination of magnetic and non-magnetic materials, is investigated. The finite element technique is used to calculate the cogging torque of a real PMSG design for a small wind turbine, with and without using compound pre-slotting. The results show that cogging torque can be reduced by a factor of 48% with this technique, while avoiding the main drawback of the conventional pre-slotting technique: the reduction of induced voltage due to leakage flux between stator teeth. Furthermore, through a combination of pre-slotting and other cogging torque optimization techniques, 84%, cogging torque can be eliminated for a given design.

The regulation of hepatic very-low-density lipoprotein (VLDL) secretion plays an important role in the pathogenesis of dyslipidemia and fatty liver diseases. VLDL is controlled by hepatic microsomal triglyceride transfer protein (MTTP). Mttp is regulated by carbohydrate response element binding protein (ChREBP) and small heterodimer partner (SHP). However, it is unclear whether both coordinately regulate Mttp expression and VLDL secretion. Here, adenoviral overexpression of ChREBP and SHP in rat primary hepatocytes induced and suppressed Mttp mRNA, respectively. However, Mttp induction by ChREBP was much more potent than suppression by SHP. Promoter assays of Mttp and the liver type pyruvate kinase gene revealed that SHP and ChREBP did not affect the transactivity of each other. Mttp mRNA and protein levels of Shp^/– mice were similar to those of wild-type; however, those of Chrebp^–/–Shp^–/– and Chrebp^–/– mice were much lower. Consistent with this, the VLDL particle number and VLDL secretion rates in Shp^–/–- mice were similar to wild-type, but were much lower in Chrebp^–/– and Chrebp^–/–Shp^–/–- mice. These findings suggested that ChREBP rather than SHP regulates VLDL secretion and that ChREBP and SHP do not affect the transactivities of each other.

We use Matlab 3D finite element fluid flow/transport modelling to simulate localized wellbore temperature events of order 0.05-0.1oC logged in Fennoscandia basement rock at ~ 1.5km depths. The temperature events are approximated as steady-state heat transport due to fluid draining from the crust into the wellbore via naturally occurring fracture-connectivity structures. Flow simulation is based on the empirics of spatially-correlated fracture-connectivity fluid flow widely attested by well-log, well-core, and well-production data. Matching model wellbore-centric radial temperature profiles to a 2D analytic expression for steady-state radial heat transport with Peclet number Pe ≡ r0φv0/D (r0 = wellbore radius, v0 = Darcy velocity at r0, φ = ambient porosity, D = rock-water thermal diffusivity), gives Pe ~ 10-15 for fracture-connectivity flow intersecting the well, and Pe ~ 0 for ambient crust. Darcy flow for model Pe ~ 10 at radius ~ 10 meters from the wellbore gives permeability estimate κ ~ 0.02Darcy for flow driven by differential fluid pressure between least principal crustal stress pore pressure and hydrostatic wellbore pressure. Model temperature event flow permeability κm ~ 0.02Darcy is related to well-core ambient permeability κ ~ 1µDarcy by empirical poroperm relation κm ~ κ exp(αmφ) for φ ~ 0.01 and αm ~ 1000. Our modelling of wellbore temperature events calibrates the concept of reactivating fossilized fracture-connectivity flow for EGS permeability stimulation of basement rock.

Alena Tensor is a recently discovered class of energy-momentum tensors that provides mathematical framework in which, as demonstrated in previous publications, the description of a physical system in curved spacetime and its description in flat spacetime with fields are equivalent. The description of a system with electromagnetic field based on Alena Tensor can be used to reconcile physical descriptions. 1) In curvilinear description, Einstein Field Equations were obtained with Cosmological Constant related to the invariant of the electromagnetic field tensor, which can be interpreted as negative pressure of vacuum, filled with electromagnetic field. 2) In classical description for flat spacetime, three densities of four-forces were obtained: electromagnetic, gravity, and the force responsible for the Abraham-Lorentz effect (radiation reaction force). Obtained connection of Einstein tensor with gravity and radiation reaction force, after transition to curvilinear description, excludes black hole singularities. There was obtained Lagrangian density and generalized canonical four-momentum, containing electromagnetic four-potential and a term responsible for other two forces. In this description charged particles cannot remain at complete rest and should have spin, their energy results from the existence of the energy of the magnetic moment and the density of this energy is part of the Poyting four-vector. The distribution of charged matter was expressed as polarization-magnetization stress-energy tensor, what may explain why gravity is invisible in QED. 3) In quantum picture, QED Lagrangian density simplification was obtained, and the Dirac, Schrödinger and Klein-Gordon equations may be considered as approximations of the obtained quantum solution. Farther use of Alena Tensor in unification applications was also discussed.

The direct detection of dark matter constituents, in particular the weakly interacting massive particles (WIMPs), is central to particle physics and cosmology. In this paper we develop the formalism for WIMP-Nucleus induced transitions from isomeric nuclear states. We specialize it in the case of the experimentally interesting target 180 Ta

The Aether Physics Model (APM) presents a radical reinterpretation of fundamental physics, offering potential solutions to long-standing problems in Quantum Mechanics and General Relativity. This paper explores the core concepts and equations of the APM, demonstrating how they provide a unified framework for understanding the nature of space, time, matter, and fundamental forces. We examine the implications of the APM's quantized Aether structure, the role of the Singularity and Gforce, and the reinterpretation of fundamental constants and forces. The model's predictions regarding dark matter, neutron content in stable matter, and the unification of forces are discussed, along with potential experimental tests. Additionally, we introduce the loxodrome concept and toroidal particle topology as central elements in explaining fundamental particles and forces. While speculative, the APM offers a thought-provoking alternative to standard physics models and warrants further investigation.

Fine particulate matter (PM_2.5) can enter the lungs and cause premature death in millions of people worldwide every year. More and more international scholars are paying attention to the potential harm of PM_2.5 and how to reduce its negative impact. Reducing air pollution and its negative impacts is an important function of green spaces. Many scholars have conducted research on the impact of green spaces on PM_2.5. This article attempts to comprehensively review past related research. This is undoubtedly beneficial for people to better understand the impact of green spaces on PM_2.5 and optimize green spaces accordingly to reduce PM_2.5 concentration. This article first provides a detailed introduction to the impact of plants on PM_2.5 pollution from the perspective of the mechanism of action. Then, this article provides a review of the different impacts of green space types and morphological factors on the surrounding environment PM_2.5. In addition, this article outlines the range of the impact of green spaces on PM_2.5 in the environment. This article categorizes green spaces into different types such as road green spaces, commercial and residential green spaces, and parks and squares, and explores the impact of green spaces on PM_2.5 in the environment. This article analyzes the impact of various parts of a single plant on PM_2.5 in the environment from a single plant perspective. Finally, this article analyzes which factors in the surrounding environment can affect the impact of green spaces on PM_2.5 pollution in the environment. A review of relevant research is also beneficial for people to have a more comprehensive understanding of current research progress and guide future research to better carry out.

In this paper, we explore the hypothesis that topological defects formed in the quark-gluon plasma (QGP) of the early universe, specifically flux tubes and domain walls, could serve as stable dark matter candidates. Theoretical analysis of the QCD vacuum structure reveals that these defects can form due to nontrivial topological configurations, with the Lagrangian density incorporating topological terms. We model the formation and stability of flux tubes and domain walls, estimating their energy densities and dynamics within the QGP. Flux tubes, with energy per unit length approximately given by $\mu \approx \frac{\sigma}{g_s^2}$, and domain walls, characterized by a surface energy density $\sigma_{\text{DW}} \sim \Lambda_{\text{QCD}}^3$, exhibit unique gravitational signatures. These signatures include distinct gravitational lensing patterns due to their linear and planar mass distributions, making them detectable through astrophysical surveys. Furthermore, their minimal interaction with conventional matter aligns well with observational constraints on dark matter properties. We discuss potential experimental approaches for detecting these defects, including high-energy collider experiments and detailed analysis of gravitational lensing data. Our findings suggest that topological defects in the QGP provide a compelling and novel solution to the dark matter problem, offering a new direction for both theoretical investigation and experimental verification.

Urban air pollution is a significant threat to both the environment and public health. Primarily originating from traffic emissions, particulate matter is identified as the most prevalent and toxic pollutant in cities. In recent years, street vegetation has emerged as a nature-based solution to improve urban air quality. However, to achieve this goal, proper placement of vegetation is crucial. This study critically investigates how different street tree placement strategies affect the local air quality, based on a model calibrated using existing air quality measurements from one of the most polluted streets in Glasgow. We then test the local air quality effects of tree orientation, spacing, shape, porosity, size, species, and wind directions. The findings suggest that trees effectively enhance air quality, particularly when implemented on the leeward side of the street. To achieve optimal effectiveness, the spacing of trees require careful alignment with the aspect ratio, as haphazard planting could lead to unfavorable results. The insights on improving air quality in Glasgow's street canyons, complements the objectives of the ‘Glasgow Avenues Programme’ and can be included in its Low Emission Zones to co-benefit the environment and the wellbeing of the local community.

In this study, we adopt a unique approach by utilizing the responses of human autonomic systems to gauge the abundance of pollutants in inhaled air. Air pollution has numerous impacts on human health on a variety of time scales. This study uses biometric observations of the human autonomic response on the second timescale to investigate how the human body autonomically responds to inhaled pollutants in microenvironments, including particulate matter. PM1 and PM2.5, carbon dioxide (CO2), nitrogen dioxide (NO2), and nitric oxide (NO) on small temporal and spatial scales. These pollutants are exemplars of the wider human exposome. We compare two experimental approaches that use a similar methodology, employing a biometric suite to capture the physiological responses of cyclists and sensors to monitor the pollutants in the air surrounding them. We employ machine learning algorithms to estimate the levels of these pollutants and decipher the body’s automatic reactions to them. We observed high precision in predicting PM1, PM2.5 and CO2 using a limited set of biometrics from participants. Although the predictions for NO2 and NO were reliable at lower concentrations, the precision varied throughout the data range. This discrepancy suggests the potential to improve our models with more comprehensive data collection or advanced machine learning techniques.

Machine learning has become more prevalent as a tool used for biogeochemical analysis in agricultural management. However, a common drawback of machine learning models is the lack of interpretability, as they are black boxes that provide little insight into agricultural management. To overcome this limitation, we compared three tree-based models (decision tree, random forest, and gradient boosting) to explain soil organic matter content through Shapley additive explanations (SHAP). Here, we used nationwide data on field crops, soil, terrain, and climate across South Korea (n = 9,584). Using the SHAP method, we identified common primary controls of the models, for example, regions with precipitation levels above 1400 mm and exchangeable potassium levels exceeding 1 cmol+ kg-1, which favor enhanced organic matter in the soil. Different models identified different impacts of nutrients on the organic matter level in the soil. The SHAP method is practical for assessing whether different machine learning models yield consistent findings in addressing these inquiries. Increasing the explainability of these models means determining essential variables related to soil organic matter management and understanding their associations for specific instances.

Soil moisture reserve is a key factor in maintaining soil fertility and all other related ecosystem services (including carbon sequestration, soil biodiversity, soil erosion control). In semiarid blown-sand areas under aridification water preservation is a particularly crucial task for agriculture. The international Diverfarming project (2017–2022) within the EU Horizon 2020 Program focused on the impacts of crop diversification and low-input practices in all pedoclimatic regions of Europe. In the three-year experiment conducted in the Pannonian region the impacts of intercropping asparagus with different herbs on some provisioning and regulating ecosystem services were evaluated in the Kiskunság sand regions. Relying on the findings based on a range of measured physical and chemical soil parameters and on crop yields and qualitative properties, advice was formulated for farmers. The message drawn from the experiment is somewhat ambiguous. The local farmer agrees that crop diversification improves soil quality, but he denies that it would directly influence farm competitiveness, which primarily depends on cultivation costs (such as fertilization, plant protection and labour). Further analyses are needed to prove the long-term benefits of diversification through enriching soil microbial life and the possible reduction of fertilizer use while water demand is kept at a low level and the same crop quality is ensured.

The cyclic universe theory is a model of cosmic evolution according to which the universe undergoes endless cycles of expansion and cooling, each beginning with a big bang and ending in a big crunch. In this paper, the researcher finds a unique property of Space-time, this particular and marvelous nature of space shows us that space can shrink, expand, and stretch. This property of space is caused the size of the Universe changing over time: growing or shrinking. The observed accelerated expansion, which relates the stretching of Shrunk space for the new theory, is derived. This model is based on three underlying notions: First, the Big Bang was not the beginning of Space-time, but rather at the very beginning fraction of a second there was an infinite force of infinite Shrunk space in the cosmic singularity, that force gave rise to the big bang and caused the rapidly growing of space-time, and all other forms of energy are transformed into matter and radiation and a new period of expansion and cooling begins. Second, there was a previous phase leading up to it, with multiple cycles of contraction and expansion that repeat indefinitely. Third, the two principal long-range forces are the gravitational force and the repulsive force generated by shrunk space. They are the two most fundamental quantities in the universe that govern cosmic evolution. They may provide the clockwork mechanism that operates our eternal cyclic universe. The space will not continue to expand forever, no need however, for dark energy and dark matter. This model of Space-time and its unique properties enables us to describe a sequence of events from the Big Bang to the Big Crunch.

We discuss the neutron skins of 48Ca and 208Pb. We review and critically examine modern predictions and empirical constraints, with special attention to the dierent interpretations of the ndings from the PREX-II experiment and the recently reported value of the neutron skin in 48Ca extracted from the CREX experiment. We argue that, in the spirit of the ab initio philosophy, the path to understanding the behavior of dense neutron-rich matter must not circumvent fundamental nuclear forces. Based only on that argument, a thick neutron skin in 208Pb is highly unlikely.

The question of whether some neutrinos are tachyons remains unresolved although various evidence from cosmic ray and other data exists that the electron neutrino has an effective $m_\nu^2\approx -0.25 eV^2,$ which would require that one or more mass states is also tachyonic. In 2013 the $3+3$ model of the neutrino masses, which includes one tachyonic mass state, was proposed based on supernova SN 1987A neutrino data. Here we update evidence for tachyonic electron neutrinos and the $3+3$ model and discuss one test which could prove conclusive. The update of earlier evidence includes many new elements, including new data which makes the earlier cosmic ray evidence more robust, new results on cosmic ray composition, the ankle of the spectrum, leptonic cosmic ray data, and the statistical significance of finding the three large neutrino masses stipulated in the $3+3$ model. Barring a galactic supernova, which occur only around twice a century, a decisive test of the $3+3$ model could involve observing an extragalactic supernova neutrino burst, that is a cluster of neutrinos in a specific time window well beyond what chance would predict. Even though existing searches for such bursts have yielded only upper limits on the extragalactic supernova frequency within a certain distance, it is shown that the choice of a one-day window for possible neutrino clusters in time might be far more sensitive. A search using a one day time window could be done using existing data, and if a signal is found it would confirm the $3+3$ model. Of course, the absence of any day-long neutrino burst would not disprove the model, since it could mean only that the nearest supernova during the period when detectors were active was simply too far to be detected. Finally, apart from testing the 3 + 3 model, an alternative type of search is suggested using existing hadronic cosmic ray data (from the IceCube Collaboration) that might verify the tachyonic neutrino hypothesis.

Post-traumatic stress disorder (PTSD) is a chronic psychiatric disorder that occurs following exposure to traumatic events. The prevalence of PTSD is estimated to be 5-10% worldwide, and it is associated with significant distress and disability. Recent evidence suggests that PTSD may be a risk factor for the development of subsequent neurodegenerative disorders, including Alzheimer’s dementia and Parkinson’s disease. Identification of biomarkers known to be associated with neurodegeneration in patients with PTSD would shed light on the pathophysiological mechanisms linking these disorders, and would also help in the development of preventive approaches aimed at reducing the risk of neurodegenerative disorders in PTSD. In the current review, the PubMed and Scopus databases were searched for studies aimed at identifying genetic, biochemical, neuroimaging or behavioral markers associated with neurodegeneration in patients with PTSD. Out of a total of 342 citations retrieved, 29 relevant studies were identified for inclusion in the review. The results of these studies suggest that several potentially relevant biological markers, including cerebral cortical thinning, disrupted white matter integrity, specific genetic polymorphisms, immune-inflammatory alterations, vitamin D deficiency, metabolic syndrome and parasomnias, may be associated with an increased risk of neurodegeneration in patients with PTSD. Though many of these results need replication, they highlight a number of biological pathways that plausibly link PTSD with neurodegenerative disorders, and suggest potentially valuable avenues for prevention and early intervention in this patient population.

In the article, the fireball formed in the collision of relativistic nuclei is considered as a quantum object. Based on this, an attempt is made to explain the difference in the measurements of hyperon yields in the two experiments - NA49 and NA57. Using the basic principles of quantum mechanics, it was shown that a fireball can have two quantum states - with and without ignited Quark-Gluon Plasma (QGP). With an increase of the collision energy of heavy ions, the probability of QGP ignition increases. At the same time, the probability of the formation of fireball without QGP ignition also remains nonzero even at nuclear collision energies that are much higher than the threshold QGP formation energy, which may be erroneously considered to be fixed and which is intensively sought in modern heavy ion accelerators. Thus, at SPS energy of heavy ion collisions \sqrt{s_{NN}} = 17.3 GeV, which is much higher than the assumed threshold energy of QGP formation in the region around or slightly above of \sqrt{s_{NN}} = 3 GeV, only half of the central collisions of heavy ions bring to the formation of a fireball consisted of deconfined matter (quarks and gluons), the remaining half of the collisions lead to the formation of a fireball from only hadronic matter (mesons, nucleons, hyperons etc.).

Background. Diesel exhaust particles (DEPs) have a great impact on general increase of atopic diseases worldwide. However, it is still unknown whether DEPs induce systemic B-cell IgE class switching in secondary lymphoid organs or locally in lungs, in inducible bronchial-associated lymphoid tissue (iBALT). The aim of this work was to identify the exact site of DEPs mediated B-cell IgE class switching and pro-allergic antibodies production. Methods. We immunized BALB/c mice with different OVA doses (0.3 and 30 µg) intranasally in the presence and absence of two types of DEPs, SRM1650B and SRM2786. We used low (30 µg) and high (150 µg) DEPs doses in our study. Results. Only high DEP dose induced IgE production regardless of particle type. Local IgE class switching was stimulated upon treatment with both types of particles with both low and high antigen doses. Despite the similar ability of two standard DEP samples to stimulate IgE production, their ability to induce iBALT formation and growing, was markedly different upon co-administration together with low antigen doses. Conclusion. DEPs induced local IgE class switching takes place in pre-existing iBALTs, independently of de novo iBALT formation, at least in the case of SRM1650B co-administrated with low antigen doses.

Degraded soils causing from natural and human affects are universal in arid and semi-arid regions all over the world. Bentonite and humic acid (BHA) are increasingly being tested to remediate these degraded lands with potential benefits on crop production and soil health. The objective of this paper was to determine the residual effects four to five years after a one-time BHA application at six rates on (i) dynamic changes in soil properties, and (ii) oat crop productivity parameters, in a dryland farming ecosystem. With increasing rates of one-time BHA application, soil profile water storage displayed a piecewise linear increase plus plateau, whereas soil electrical conductivity, pH and bulk density were all reduced significantly (P < 0.05) in the 0-20 cm and 20-60 cm layers. The improved soil environments gave rise to an increased activity of soil enzymes urease, invertase and catalase that respectively reached the peak values of 97%, 37% and 32% at the rates of 21 to 24 Mg BHA ha-1. These conversely boosted soil nutrient turnover, leading to a 40% higher soil available P. Compared with the control treatment, application of BHA at the estimated optimum rate (roughly 24 Mg ha-1) increased grain yield by 20%, protein yield by 62%, water use efficiency by 41%, and partial factor productivity of N by 20%. Results of this study showed for the first time that a one-time BHA application would be a new and effective strategy to combat land degradation, drought, and promote a sustainable soil micro-ecological environment in dryland agroecosystem under a varying climate scenario.

Herein is introduced a simple scalar field model derived from classical based kinetic energy, gravitational potential energy, and Special Relativity’s rest mass energy. By applying a classical orbit over the scalar field, relativistic effects are predicted. The scalar field is then applied to a classical model of the Hydrogen atom resulting in a relativistic effect equal to the binding energy of the Hydrogen atom. In addition, the model derives the fine structure constant due to the gravitational effect. The relativistic effects are then discretized in increments equal to the model’s gravitational induced constant. The discretization produces the Hydrogen atom spectral emissions and an angular moment equal to Planck’s reduced constant. The model is not presented as a replacement for current theory, rather it is for inspection and illustration of how a simplistic model may offer a fundamental bridge between the more complex, time proven theories of General Relativity and Quantum Mechanics.

The combination of organic matter, iron oxide, and clay minerals is of great significance for the adsorption of copper ions (Cu). The purpose of this study is to explore the characteristics of Cu adsorption and laws governing Cu complexation to organic–inorganic, organic–clay mineral, and iron-oxide–clay mineral complexes in the sediments in the estuary of plateau fault and sinking lake——Dianchi Lake. In this study, Cu adsorption tests were performed on the three complexes, in order to study the kinetic behavior of adsorption, Langmuir and Freundlich isotherm models were used. The samples before and after adsorption were characterized via scanning electron microscope (SEM), Fourier infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Our results show that, the Freundlich isotherm models model was able to describe adsorbent behavior in comparison to the Langmuir models. During the Cu adsorption process, the iron-oxide–clay mineral complex is able to adsorb Cu, via coordination exchange, through the –OH contained therein. Organic-matter–clay mineral complexes bonded to the surfaces of clay minerals by replacing the hydroxyl groups with functional groups (carboxyl groups or phenolic hydroxyl groups) contained in the organic matter. Organic–inorganic composites then adsorbed Cu through the coordination exchange of –OH in the polar functional groups of alcohols, phenols, and carboxylic acids. The adsorption capacity of Cu in these three sediment complexes was observed to have the following order: organic–inorganic complex &gt; organic-matter–clay mineral complex &gt; iron-oxide–clay mineral complex. The semi-quantitative analysis results of Fourier Infrared Spectroscopy show that the organic matter (changes in the peak area of functional groups such as carboxyl groups) in the organic-inorganic composite material has an important effect on the amount of copper ions adsorbed by clay minerals.

Life cycle assessment (LCA) is being included formally in EcoDesign regulations. Especially product carbon footprint will be mandatory in Europe. However, life cycle impact assessment including global warming potential (GWP) in LCA is hampered by several challenges. One of these is lack of water vapor characterization indexes for GWP. A life cycle inventory profile for air transport fuel including water vapor emissions is evaluated with state-of-the-art practice, i.e. EF Method and ILCD 2011 Midpoint+ and neglecting water vapors high altitude GWP compared to carbon dioxide. Then the characterization factor in GWP100 for water vapor and alternate normalization for particulates are introduced. The results are compared. The main findings are that the EF method and ILCD both generate rather realistic results for Particulate Matter and Respiratory Inorganics mid-point indicators, respectively, but the amount of premature deaths should be better allocated to different specific emissions, and that water vapor may dominate the GWP100 result over the usual carbon dioxide. LCIA mid-points need measurable and understandable bases. The common knowledge of water vapor’s GWP100 should not be neglected in LCIA for air transport and beyond where relevant.

Time evolution operators of a strongly ionizing medium are calculated by a time-dependent unitary transformation (TDUT) method. The TDUT method has been employed in quantum mechanical system composed of discrete states. This method is especially helpful for solving molecular rotational dynamics in quasi-adiabatic regimes because the strict unitary nature of the propagation operator allows us to set the temporal step size large; a tight limitation on the temporal step size ($\delta t <<1$) can be circumvented by the strict unitary nature. On the other hand, in a strongly ionizing system where the Hamiltonian is not Hermitian, the same approach cannot be directly applied because it is demanding to define a set of field-dressed eigenstates. In this study, the TDUT method was applied to the ionizing regime using the Kramers-Henneberger frame, in which the strong-field-dressed discrete eigenstates are given by the field-free discrete eigenstates in a moving frame. Although the present work verifies the method for a one-dimensional atom as a prototype, the method can be applied to three-dimensional atoms, and molecules exposed to strong laser fields.

The aim of this study was to develop a basic model to predict enteric methane emission from dairy cows and to update operational calculations for the national inventory in Norway. Basic models were developed using a database with 63 treatment means from 19 studies. The database included records for enteric CH4 production (MJ/day), dry matter intake (DMI), and dietary nutrient composition. The basic models were evaluated against an external database (n=36, from ten studies) along with other extant models. When evaluated by low root mean square prediction errors and high concordance correlation coefficients, the developed basic models that included DMI, dietary concentrations of fatty acids and neutral detergent fiber performed slightly better in predicting CH4 emissions than extant models. In order to propose country-specific values for the CH4 conversion factor Ym (% of gross energy intake partitioned into CH4) and thus to carry out the national inventory for Norway, the existing operational model was updated for the prediction of Ym over a wide range of feeding situations using energy corrected milk and dietary concentrate share as predictor variables. Input values of Ym were updated based on the results from the basic models. The predicted Ym ranged from 6.22 to 6.72%. In conclusion, the prediction of CH4 production from dairy cows was improved with the help of newly published data, which enabled an update of the operational model for calculating the national inventory of CH4 in Norway.

The sustainable production of food faces formidable challenges. Foremost is the availability of arable soils, which have been ravaged by the overuse of fertilizers and detrimental soil management techniques. As such, maintenance of soil quality, and reclamation of marginal soils, has become an increasingly important endeavor. Recently, there has been emerging interest in the use of biochar, a carbon rich, porous material thought to improve various aspects of soil performance. Biochar (BC) is produced through the thermochemical decomposition of organic matter at high temperature in an oxygen limited environment, in a process known as pyrolysis. Importantly, the source of organic material, or ‘feedstock,’ used in this process and different parameters of pyrolysis, especially temperature, determine the chemical and physical properties of biochar. Incorporation of BC impacts soil-water relations, tilth and nutrient status, pH, soil organic matter (SOM), and microbial activity. Soil amendment with BC has been shown to have an overall positive impact on soil health and crop productivity; however, initial soil properties need to be considered prior to the application of BC. There is an urgent need to understand the effects of long-term field application of BC and how it influences the soil microcosm. This knowledge will facilitate predictable enhancement of crop productivity and meaningful carbon sequestration.

A reduced-dimension (RD) method based on the proper orthogonal decomposition (POD) technology and the linearized Crank-Nicolson mixed finite element (CNMFE) scheme for solving the 2D nonlinear Extended Fisher-Kolmogorov (EFK) equation is proposed. The method reduces CPU runtime and error accumulation by reducing the dimension of the unknown CNMFE solution coefficient vectors. For this purpose, The CNMFE scheme of the EFK equation is established and the uniqueness, stability and convergence of the CNMFE solutions are discussed. Subsequently, the matrix-based RDCNMFE scheme is derived by applying the POD method. Furthermore, the uniqueness, stability and error estimates of the linearized RDCNMFE solution are proved. Finally, numerical experiments are carried out to validate the theoretical findings. In addition, we contrast the RDCNMFE method with the CNMFE method, highlighting the advantages of the dimensionality reduction method.

Aiming at the problems of high cost of manual pulling, low reliability of existing pulling devices, high breaking rate and high leakage rate in the process of cotton stalk reuse after leaving the field in Xinjiang cotton area, a loosening soil and root-cutting cotton stalk pulling the setting machine has been researched and designed, established the root-cutting force model, calculated and optimized the key parameters of the V-shaped root-cutting knife, and determined the range of slide cutting angle, cutting edge angle and soil entry angle. The shoveling process simulation of V-shaped root-cutting knife and root-soil complex was constructed, and the working mechanism of V-shaped root-cutting knife was clarified. In order to verify the reliability and operation performance of the V-shaped root-cutting knife, the slide cutting angle, cutting edge angle and soil entry angle were used as the test factors, the response surface test of three-factors and three-levels was carried out with root-breaking force and mean value of the cutting resistance as the test index. The test results were analyzed by variance analysis, the significant of influencing factors on the root-breaking force are in a descending order as: slide cutting angle, cutting edge angle, soil entry angle; the degree of influence on the mean value of the cutting resistance are as follows: slide cutting angle, soil entry angle, cutting edge angle. In order to make the V-shaped root-cutting knife achieve the optimal working state, the parameters of the test index were optimized, and the optimal design parameters of the V-shaped root-cutting knife were set as follows: the slide cutting angle was 48.3°, cutting edge angle was 43.4°, and soil entry angle was 26.2°. The field uprooting test showed that the average pass rate of root breakage was 94.8% and the average pull-out rate of the cotton stalk was 93.2%. This study provides theoretical guidance for the development of root breaking mechanism of cotton straw harvester.

Total ankle replacement (TAR) implants are an effective option to restore the range of motion of the ankle joint for arthritic patients. An effective tool for analyzing these implants’ mechanical performance and longevity in-silico is finite element analysis (FEA). ABAQUS FEA was used to statically analyze the von Mises stress and contact pressure on the articulating surface of the bearing component in two newly installed fixed-bearing total ankle replacement implants (the Wright Medical INBONE II and the Exactech Vantage). This ultra-high molecular weight polyethylene (UHMWPE) bearing commonly fails and is the cause for surgeon revisions. Six different FEA models for various gait percentages during stance (10%-60%) were created. They varied in magnitude of the compressive load and the ankle dorsiflexion/plantarflexion angle. The results indicated that the von Mises stress and contact pressure distributions increased as compressive load increased, and the largest magnitudes occurred at high dorsiflexion angles (15-30°). High magnitudes occurred in regions where the thickness of the bearing was the least. Additionally, high contact pressures were examined in areas near the talar component's edge or at the bearing's edges. To the author’s knowledge, this is the first study available to the research community that analyzes the Vantage implant with FEA. This study lays an essential foundation for future researchers in presenting a thorough literature review of TAR and methods for a simple FEA model setup. This study provides valuable information that can be beneficial to medical company designers and orthopedic surgeons in understanding the stress response and contact pressure of TAR implants during use.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

This study explores the significance of active suspension systems for vehicles with lower chassis compared to conventional ones, aiming at the development of future automobiles. Conventional linear MR (Magneto-Rheological) dampers were found inadequate in ensuring sufficient vibration control because the vehicle's chassis becomes lowered in the unmanned vehicles or purposed based vehicles. As an alternative, a rotary type of MR damper is proposed in this work. The proposed damper is designed based on pre-specified design parameters through mathematical modeling and magnetic field analyses. Subsequently, a prototype of the rotary MR damper identical to the design is fabricated, and effectiveness is shown through experimental investigations. In configuring the experiments, a proportional-integral (PI) controller is employed for current control to reduce the response time of the damper. The results presented in this work provides useful guidelines to develop a new type of MR damper applicable to various types of future vehicles’ suspension systems with low distance from the tire to the body floor.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

This study identifies the facies and degrees of hydrothermal alteration related to the low sulphida-tion epithermal Kestanelik Au deposit in the Biga Peninsula metallogenic province through petro-graphic studies and analysis of geochemical characteristics, such as mass changes, molar element ratios, and alteration indices. The gold mineralization is located in silicified zones containing veins and stockwork veinlets of quartz. These zones are found within the Permian-Upper Cretaceous aged Çamlıca basement metamorphics and Eocene aged Kestanelik granodiorite of the Karabiga Massif on the Biga Peninsula. The mineralization is influenced by tectonic structures such as quartz veins and faults. In the Kestanelik Au deposit, common hydrothermal alteration occurs mainly in the metamorphics and granodiorite, and less often in volcanic rocks. Based on miner-alogical and geochemical studies conducted on altered samples, four different alteration facies were defined as silicic, sericitic, argillic and propylitic, which show remarkable differences in the behaviour of REE, Si, K, Al, Na and Ca elements. The characterization of rocks subjected to hy-drothermal alteration that are most influenced by diverse K metasomatism with the largest K gains and losses of Na-Ca, is illustrated by molar element ratio plots. Depending on the severity of K-metasomatism, gold mineralization rises with increasing K trends towards gold ore veins. In the Kestanelik Au field, the alteration types of argillic, sericitic, propylitic and adularia from the alter-ation zones enclosing the Au ore veins, were revealed by the alteration index and chlo-rite-carbonate-pyrite index. Mass changes in the altered rocks indicate that there are gains in Si, K, Al, and losses in Na and Ca with the increasing intensity of alteration towards the Kestanelik ore veins. The results confirm the presence of silicic and K-metasomatic (sericite and argillic) propylit-ic (Fe-rich chloride) alteration zoning extending from the inner regions to the outer regions, which characterize the epithermal ore systems. It has been revealed from the data obtained in this study that the intensity of potassium metasomatism that occurs in acidic rocks is greater than that found in intermediate and mafic rocks. The hydrothermal fluids that cause alteration in Kestanelik Au mineralization and host rocks had low contents of REE due to REE mobilization, and the kaolini-zation of feldspars and micas, and the chloritization of biotite and feldspars, may cause negative Eu anomalies.

Cretan lyra is a stringed instrument very popular on the island of Crete, Greece and an important part of its musical tradition. For stringed musical instruments, the air mode resonance plays a vital part in their sound, especially in the low frequency range. For this study, the air mode resonance of a Cretan lyra is investigated with the use of finite element method (FEM). Two different FEM acoustic models were utilized: first, a pressure acoustics model with the Cretan lyra body treated as rigid was used to provide an approximate result; secondly, an acoustic-structure interaction model was applied for a more accurate representation. In addition, acoustic measurements were performed to identify the air mode resonance frequency. Results of this study reveal that the acoustic-structure interaction model has a 3.7% difference regarding the actual measurements of the resonance frequency. In contrast, the pressure acoustics solution is approximately 13.8% too high compared with the actual measurements. Taken together, findings of this study support the idea that utilizing FEM acoustic-structure interaction models could possibly predict more accurately the vibroacoustic behavior of musical instruments, which in turn can enable the determination of key aspects that can be used to control the instrument’s tone and sound quality.

We overview recent findings achieved in the field of model-driven development of additively manufactured porous materials for development of a new generation of bioactive implants for orthopedic applications. Porous structures produced of biocompatible titanium alloys by selective laser melting can present a promising material to design scaffolds with regulated mechanical properties and with capacity to be loaded with pharmaceutical products. Adjusting pore geometry, one could control elastic modulus and strength/fatigue properties of the engineered structures to be compatible with bone tissues, thus preventing the stress shield effect when replacing a diseased bone fragment. Adsorption of medicals by internal spaces would make it possible to emit the antibiotic and anti-tumor agents into surrounding tissues. We critically analyze the recent advances in the field featuring model design approaches, virtual testing of the designed structures, capabilities of additive printing of porous structures, biomedical issues of the engineered scaffolds and so on. A special attention is paid to highlight the current troubles in the field and the ways of their solutions.

The degradation of Proton-exchange membrane fuel cell (PEMFC) gasket materials is crucial in electric vehicles as it can cause hazardous hydrogen fuel leaks, which are usually due to high temperatures, pressures, and hydrogen fuel exposure. Degradation of gasket materials in PEMFC presents a critical concern for electric vehicle safety due to potential hydrogen fuel leaks. This study utilizes finite element analysis (FEA) to assess the suitability of gasket materials for PEMFC applications, focusing on aging and tensile conditions. The dual degradation framework, incorporating contact pressure and von Mises stress, is employed to evaluate Liquid Silicon Rubber (LSR) and Ethylene Propylene Diene Monomer (EPDM) materials. Under aging techniques, the Yeoh model exhibits the least Mean Absolute Percentage Error (MAPE) and computational cost of 0.27 seconds, while the Ogden model records the highest computational cost of 0.89 seconds. In evaluating MAE, Root Mean Square Error (RMSE), and R-squared metrics, LSR and EPDM materials demonstrate respective averages of 0.25%, 0.275%, 0.945%, and 0.815%, 0.685%, 0.77%. Tensile testing (Uniaxial) reveals RMSE and MAE values of 0.30%, 0.40%, and 0.50%, 0.40%, respectively. FEA proves instrumental in identifying suitable gasket materials for PEMFC applications. LSR emerges as the superior choice, demonstrating enhanced FEA modelling performance under aging and tensile conditions. These findings contribute valuable insights to the design and development of improved gasket materials, bolstering the safety and reliability of electric vehicles.

The Apetala2/ethylene response factor superfamily refers to a group of transcription factors that share a conserved AP2 DNA binding domain. These factors have been found to have different roles in plant responses to both biotic and abiotic stresses. Samples of hexaploid wheat, tetraploid pasta (or durum wheat), and diploid wheat progenitors were selected. The 29 dehydration-responsive element binding transcription factors in these samples were downloaded from NCBI GenBank for six different countries: Iran, China, Italy, France, Afghanistan, and Azerbaijan. The AP2 domain sequences were identified from the dehydration-responsive element binding transcription factors using PROSITE, ProDom, and SMART software. Next, all sequences were aligned using Multalin and Jalview software. The aligned sequences were then analyzed to identify amino acid locations, types, and frequencies. The multiple alignments showed that approximately 76% of the amino acid residues in the AP2 domains are conserved. According to the amino acid analysis, alanine, serine, and glutamic acid are the most abundant amino acids found in three motifs. The performed phylogenetic analysis illustrates the role of geographical effects on the transcription factor sequences of bread wheat in the Middle East. Significant differences were found between Iranian and Chinese transcription factor sequences. Moreover, genetic variation was observed in the transcription factors of Italian sequences found in pasta and wheat progenitors. Motif structures play a critical role in the domain organization of wheat proteins to enhance the characteristics of assorted metabolic pathways. The structure of the AP2 domain was analyzed by several programs, I-TASSER for instance, to identify the α-helix, β-sheets, and the regions of some significant amino acids in the 3-D model.

The main objective of the paper is to investigate the wave propagation behaviour in composites using numerical and experimental methods. Specifically, the study focuses on the actuation of waves by two PZT transducers placed on the surface and embedded at different positions within the composites, namely the quarter and middle positions. The numerical analysis provides simulated results, while the experimental analysis involves practical testing. The paper demonstrates that the numerical results are consistent with the experimental findings. It is observed that when the PZT transducers are placed at deeper positions within the composites, the peak amplitude of the first wave packet for the A0 mode decreases. Overall, the paper contributes to the understanding of wave propagation in composites by comparing the effects of different positions of PZT transducers, both on the surface and embedded within the material. The findings highlight the influence of transducer placement on wave characteristics, particularly the reduction in peak amplitude with deeper transducer positioning.

Variable Angle Tow (VAT) laminates offer a promising alternative to classical straight fiber composites in terms of design and performance. However, analyzing these structures can be more complex due to the introduction of new design variables. Carrera's Unified Formulation (CUF) has been successful in previous works for buckling, vibrational, and stress analysis of VAT plates. Typically, one-dimensional (1D) and two-dimensional (2D) CUF models are used, with a linear law describing the fiber orientation variation in the main plane of the structure. The objective of this article is to expand the CUF 2D plate finite elements family to perform free vibration analysis of composite laminated plate structures with curvilinear fibers. The primary contribution is the application of Reissner's Mixed Variational Theorem (RMVT) to a CUF finite element model. The Principle of Virtual Displacements (PVD) and RMVT are both used as variational statements for the study of monolayer and multilayer VAT plates dynamic behavior. The proposed approach is compared to Abaqus three-dimensional (3D) reference solutions, classical theories and literature results to investigate the effectiveness of the developed models. Results demonstrate that mixed theories provide the best approximation of the reference solution in all cases.

This paper proposes a new structure of the dual-rotor hybrid-excited axial-flux permanent magnet vernier machine (DR-HEAFPMVM) with the modular stator and the consequent-pole PM (CPM) rotor for low-speed, high torque density applications such as in-wheel electric vehicles. The tooth-wound non-overlapping armature windings and direct current (DC) excitation windings are respectively arranged in stator main-teeth and split-teeth to obtain the modulated and adjustable air-gap flux densities, which result in the high torque density and outstanding flux-weakening capability. First, the design consideration, operation principle, and the air-gap flux density distributions of the proposed machine are elaborated based on the air-gap permeance function. Then, the influence of the pole ratios (PRs) and the DC excitation currents on the main electromagnetic performances of the DR-HEAFPMVM, such as the flux-weakening capability, back-electromotive force (back-EMF), on-load electromagnetic torque, loss distribution, and efficiencies, is investigated using the 3-D finite-element method (FEM). Results verify the feasibility of the flux adjustment of the DC excitation windings equipped in the split-tooth, and the design with a pole ratio of 8/1 tends to have higher torque density, higher machine efficiency, and considerable flux-weakening capability compared with the other two PRs.

(1) The article is devoted to the development of a theoretical and algorithmic basis for numerical modeling of the spontaneous potential method (SP) as applied to the study of sandy-argillaceous reservoirs. (2) In terms of coupled flows, we consider a physical-mathematical model of SP signals from an electrochemical source, with regard to the case of fluid-saturated shaly sandstone. (3) An algorithm for 2D finite-element modeling of SP signals was developed and implemented in software, along with its internal and external testing with analytical solutions. The numerical SP modeling was carried out, with determining the dependences on the reservoir thickness and porosity, the amount of argillaceous material and the type of minerals. We performed a comparative analysis of the simulated and field SP data, using the results of laboratory core examinations taken from wells in a number of fields in the Latitudinal Ob Region of Western Siberia. (4) The results of the study may be used either for the development of the existing SP techniques, by providing them with a consistent computational model, or for the design of new experimental approaches.

To enable purposeful design and implementation of automated concrete technologies, precise assessment and prediction of the complex material flow at various stages of the process chain are necessary. This paper investigates the intermediate stage of the extrusion and deposition processes in extrusion-based 3D-concrete-printing, using a numerical model based on the Particle Finite Element Method (PFEM). In PFEM, due to the Lagrangian description of motion, remeshing algorithms and the alpha shape method are used to track the free surface during large deformation scenarios. The Bingham constitutive model was used for describing the rheological behaviour of fresh concrete. This model is validated by comparing the numerically predicted layer geometries with those obtained from laboratory 3D printing experiments. Extensive parametric studies were then conducted using the numerical simulation, delineating the influence of process and material parameters on the layer geometries, the dynamic surface forces generated under the extrusion nozzle and the inter-layer interactions.

In this paper, we present a comprehensive 4D study of the early stage of plastic deformation in a polycrystalline binary AlLi alloy. The entire microstructure is mapped with X-ray diffraction contrast tomography and a set of bulk grains is further studied via X-ray topotomography during mechanical loading. The observed contrast is analyzed with respect to the slip system activation and the evolution of the orientation spread is measured as a function of applied strain. The experimental observations are augmented by the mechanical response predicted by crystal plasticity finite element simulations to analyze the onset of plasticity in details. Simulation results show a general agreement of the individual slip system activation during loading and that comparison with experiments at the length scale of the grains may be used to fine tune the constitutive model parameters.

The superharmonic imaging of tissue has the potential for high spatial and contrast resolutions, compared to the fundamental and second harmonic imaging. For this technique, the spectral bandwidth of an ultrasound transducer is divided for transmission of ultrasound and reception of its superharmonics (i.e., higher than the second harmonic). Due to the spectral division for the transmission and reception, transmitted ultrasound energy is not sufficient to induce superharmonics in media without using contrast agents, and it is difficult that a transducer has a -6-dB fractional bandwidth of higher than 100%. For the superharmonic imaging of tissue, thus, multi-frequency array transducers are the best choice if available; transmit and receive elements are separate and have different center frequencies. However, the construction of a multi-frequency transducer for intravascular ultrasound (IVUS) imaging is particularly demanding because of its small size of less than 1 mm. Here, we report a recently developed dual-element focused IVUS transducer for the third harmonic imaging of tissue, which consists of a 35-MHz element for ultrasound transmission and a 105-MHz element for third harmonic reception. For high quality third harmonic imaging, both elements were fabricated to have the same focus at 2.5 mm. The results of tissue mimicking phantom tests demonstrated that the third harmonic images produced by the developed transducer had higher spatial resolution and deeper imaging depth than the fundamental images.

The aim of this work was to determine if the development of low-cost or no-cost finite element analysis (FEA) software has advanced to the point where it can be used in place of trusted commercial FEA packages for linear static structural analyses using isotropic material models. Nonlinear structural analysis will be covered in a separate paper. Several suitable packages were identified, these underwent a process of systematic elimination when they were unable to meet the minimum imposed qualitative criteria. Three packages were chosen to be subjected to performance benchmarking, namely: Code_Aster/Salome Meca; Mecway and Z88 Aurora. SimScale, a browser-based analysis package was included as well because it met all the baseline criteria and has the potential to offer a completely cloud-based approach to computer aided engineering, potentially reshaping the way an engineering business views its operational capabilities. This paper presents the test cases and simulation results for packages that fall under the linear static structural analysis type.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

Air pollution, particularly fine particulate matter (PM2.5), poses a significant threat to public health, especially in rapidly urbanizing areas like Lagos State. Despite the severity of the issue, there is a lack of comprehensive data on PM2.5 levels and the Air Quality Index (AQI) in Lagos. This study leverages data from AirQo, an innovative air quality monitoring network using low-cost sensors, to provide a detailed assessment of PM2.5 concentrations and AQI across eight locations in Lagos State, Nigeria. This approach offers real-time, continuous monitoring, filling a critical data gap in the region's air quality management efforts. This study uses AirQo data to assess the concentration levels and spatial distribution of PM2.5 and AQI across the selected eight locations. Data on PM2.5 concentrations were obtained from AirQo sensors deployed across the eight strategic locations in Lagos. The spatial distribution of PM2.5 levels and AQI were analyzed, and the results were compared with national and international air quality standards. The findings revealed that PM2.5 levels (minimum – 6.28 µg/m3 (Ikeja) and maximum - 204.68 µg/m3 (Banana Island) in many areas of Lagos exceed annual WHO and national air quality guidelines, indicating significant health risks. The spatial analysis identified pollution hotspots, particularly in densely populated and industrial regions. The data suggested vehicular emissions and industrial activities as major contributors to high PM2.5 levels. This study underscores the severe air quality issues in Lagos State, emphasizing the need for immediate and targeted interventions to mitigate PM2.5 pollution. The use of AirQo sensors proved effective in providing accurate and timely data for air quality assessment. It is recommended that Lagos State implements stricter emission controls, promotes cleaner technologies, and enhances public transportation systems to reduce traffic-related pollution. Additionally, expanding the air quality monitoring network and incorporating more environmental data will provide a more comprehensive understanding of air pollution impacts, thereby facilitating better policy and public health decisions.

HIGHLIGHTS Special relativity has been successfully used to describe the behaviour of particles (Rossi & Hall, 1941), but there is no observation of special relativity in our world. On the contrary, there are at least two paradoxes based on special relativity: the twin paradox (Langevin, 1911) and Ehrenfest's paradox (1909). This paper is presenting a first experiment, based on Ehrenfest's paradox, where an effect of special relativity was expected but not observed. The validity of special relativity in our macro world will be questioned and an alternative will be offered. ABSTRACT After presenting the history of special relativity, the non-simultaneity of special relativity is questionned in our macro world. In addition, some incompatibilities between light clocks and the application of Lorentz transformation are presented. All this indicates some issues with special relativity which appears to be correct only for particles and would be invalid in our macro world. A new theory is presented based on an adaptation of special relativity; this new theory solves the anomalies and could be a solution to the twin paradox. This paper also presents a new experiment and its observation. The preliminary result shows that special relativity has no effect in our macro world and therefore supports the new theory. A lack of special relativistic effects has been observed in the universe (Davis et al., 2004); that is another observation where special relativity doesn't work. That second observation is also explained with the new theory.

This paper, based on the "Unified Theory of Forces," rigorously proves the formula of de Broglie's wave function. This helps us better understand the following important issues: 1) Theoretically prove and understand the essence of de Broglie's wave function; 2) Prove that when the particle's momentum P is determined, the greater the mass of the particle, the more concentrated its wave function distribution, and the weaker the interference effect; 3) Correct the spatial distribution of the wave function of free particles, proving that the wave function of free particles is strictly constrained within a finite spatial range, which is consistent with the facts we observe.

The Midwestern region of the United States has been experiencing periodic forage shortages due to frequent droughts, a growing livestock population, and reliance on traditional farming practices. This study evaluated the dry matter yield (DMY), forage nutritive value, water use efficiency (WUE), and economic viability of forage soybean [Glycine max (L.) Merr.] in a no-till winter wheat-based rainfed cropping system in the Midwest, USA. The research aimed to identify alternative summer forage crops that are drought-resilient, require lower inputs, mitigate seasonal gaps, and provide higher DMY and forage nutritive value compared to traditional forages. A four-year field experiment in a randomized complete block design with four replications assessed these parameters at various growth stages and planting dates. Results showed that forage soybean had a high DMY (~13 Mg ha-1), especially when optimally planted and harvested at the R3 stage. Forage nutritive value, including crude protein (CP), in vitro dry matter digestibility (IVDMD), and relative feed value (RFV), was highest at early vegetative stages (V2-V3), meeting livestock nutritional requirements. Forage soybean also demonstrated good WUE (21 kg ha-1 mm-1), making it suitable for water-limited regions. Economic analysis indicated substantial net profits ($322 per hectare), confirming its economic viability. The study concludes that forage soybean is a promising summer forage option for Midwest growers, offering high-quality forage, efficient water use, and economic benefits. Further research, particularly animal feeding trials, is recommended to validate its potential for widespread adoption in cropping systems.

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

Leaf mass per area (LMA) is a key structural parameter that reflects the functional traits of leaves and plays a vital role in simulating the material and energy cycle of plant ecosystems. In this study, vertical whorl-by-whorl sampling of LMA was conducted in a young Larix principis-rupprechtii plantation during the growing season at the Saihanba Forest Farm. The vertical and seasonal variations in LMA were analysed. Subsequently, a predictive model of LMA was constructed. The results revealed that the LMA varied significantly between different crown whorls and growing periods. In the vertical direction of the crown, the LMA decreased with increasing crown depth, but the range of LMA values from the tree top to the bottom was, on average, 30.4 g/m2, which was approximately 2.5 times greater in the fully expanded phase than in the early leaf-expanding phase. The LMA exhibited an allometric growth trend that increased during the leaf-expanding phase and then tended to stabilize. However, the range of LMA values throughout the growing period was, on average, 40.4 g/m2. Among the univariate models, the leaf dry matter content (LDMC) performed well (Ra2=0.45, RMSE=13.48 g/m2) in estimating the LMA. The correlation between LMA and LDMC significantly differed at different growth stages and at different vertical crown whorls. The dynamic predictive model of LMA constructed with the RDINC and DOY as independent variables was reliable in both the assessments (Ra2=0.68, RMSE=10.25 g/m2) and the validation (MAE=8.05 g/m2, FI=0.682). Dynamic simulations of crown LMA provide a basis for elucidating the mechanism of crown development and laying the foundation for the construction of an ecological process model..

We present a summary of the main results within the Scale Invariant Vacuum (SIV) paradigm based on the Weyl Integrable Geometry (WIG) as an extension to the standard Einstein General Relativity (EGR). After a brief review of the mathematical framework, where we also highlight the connection between the weak-field SIV equations and the notion of un-proper time parametrization within the reparametrization paradigm, we continue with the main results related to early Universe; that is, applications to inflation, Big Bang Nucleosynthesis, and the growth of the density fluctuations within the SIV. In the late time Universe the applications of the SIV paradigm are related to scale-invariant dynamics of galaxies, MOND, dark matter, and the dwarf spheroidals where one can find MOND to be a peculiar case of the SIV theory. Finally, within the recent time epoch, we highlight that some of the change in the length-of-the-day (LOD), about 0.92 cm/yr, can be accounted for by SIV effects in the Earth-Moon system.

Matter grows and self-assembles to produce complex structures such as virus capsids, carbon fullerenes, proteins, glasses, etc. Due to its complexity, performing pen-and-paper calculations to explain and describe such assemblies is cumbersome. Many years ago, Richard Kerner presented a pen-and-paper path integral approach to understand self-organized matter. Although successfully addressed many important problems including the yield of fullerene formation, the glass transition temperature of doped chalcogenide glasses, the fraction of boroxol rings in B2O3 glasses, the first theoretical explanation for the empirical recipe of window and Pyrex glass and the understanding of virus capsid self-assembly, still is not the primary choice when tackling similar problems. The reason lies in the fact that it diverges from mainstream approaches based on the energy landscape paradigm and non-equilibrium thermodynamics. In this context, a critical review is presented, demonstrating that the Richard Kerner method is, in fact, a clever way to identify relevant configurations. Its equations are simplified, common physical sense versions to those found in the energy landscape kinetic equations. Subsequently, the utilization of equilibrium Boltzmann factors in the transition Markov chain probabilities is analyzed within the context of local two-level energy landscape models kinetics. This analysis demonstrates that their use remains valid when the local energy barrier between reaction coordinate states is small compared to the thermal energy. This finding places the Richard Kerner model on par with other more sophisticated methods and, hopefully, will promote its adoption as an initial and useful choice for describing the self-agglomeration of matter.

Several mathematicians and physicists are working all over the globe to get a unified theory. However, most of them are discarding Einstein’s view at the very first step of their theories. This article provides a brief description about this. Also, on the basis of Koga’s theory we point out two reasons which might have caused Einstein’s failure to get a unified theory.

To study and monitor the adverse health consequences from using electronic cigarettes, a user’s puff topography, which are quantification parameters of the user’s vaping habits, plays a central role. In this work, we introduce a topography sensor to measure the mass of total particulate matter generated in every puff and to estimate the nicotine yield. The sensor is compact and low-cost, and is integrated into the electronic cigarette device to promptly and conveniently monitor the user’s daily puff topography. The topography sensor is comprised of a photometric sensor and a pressure sensor. The photometric sensor measures the mass concentration of the aerosol, based on scattering of near-infrared light from airborne particles, while the pressure sensor measures the flow rate. The topography sensor was experimented under various conditions with a wide range of atomizer power, puff duration, and inhalation pressure. The sensor’s accuracy was validated by comparing the sensor’s readings with reference measurements, and the results matched closely with the trends reported by existing studies on electronic cigarettes. An example application of tracking a user’s puff topography was also demonstrated. Our topography sensor holds great promise in mitigating health risks of vaping, and in promoting quality control of electronic cigarette products.

Low pasture biomass production and fodder scarcity are among the major challenges affecting productivity of dairy cattle farms in Sri Lanka. As a potential solution to this, two Napier hybrid cultivars CO-5 and Sampoorna were recently introduced and a field experiment was conducted to evaluate their growth, dry matter production and nutritional composition during May to September 2020. Plant measurements and samples were collected at five harvest intervals (4, 6, 8, 10 and 12 weeks after planting), with the plant samples subjected to biomass and nutritional assessments. The number of tillers and leaf length differed (P=0.01) between the two cultivars at 4 weeks harvesting interval (HI) whilst number of leaves differed at 12 HI respectively. Dry matter yield increased (P=0.16) almost linearly whilst crude protein declined exponentially with CO-5 greater than Sampoorna (P=0.057; 9.3% vs 8.7%), with increasing harvesting intervals respectively. In-vitro Organic Matter Digestibility and In-vitro Metabolizable Energy contents were similar across weeks 4, 6 and 8 but then decreased. This study demonstrates that higher dry matter yields (12.54 t/ha) can be obtained by harvesting both cultivars at 12 HI, but from a nutritional perspective harvesting at 6 HI during Yala season of the year would be optimum for farmers.

We present a summary of the main results within the Scale Invariant Vacuum (SIV) paradigm as related to the Weyl Integrable Geometry. After a brief review of the mathematical framework, we will highlight the main results related to inflation within the SIV [9], the growth of the density fluctuations [8], and the application of the SIV to scale-invariant dynamics of Galaxies, MOND, Dark Matter, and the Dwarf Spheroidals [7]. The connection of the weak-field SIV results to the un-proper time parametrization within the reparametrization paradigm is also discussed [14].

In this paper we will find that, according to holographic principle {\cite{Holografico}} and thus considering Universe as the ensemble of $\aleph$ information bits or minimum particles of mass $m_{g}$, the contribution to galactic rotation curves can be due the rest of the visible Universe through a non-local collective gravitational interaction of all particles within the Universe's horizon, as a consequence of which all particles are gravitationally entangled and form a unified statistical ensemble. Therefore, we can to describe this global effect in terms of standard local Newtonian gravity within galaxies for the explanation of flatness galactic rotation curves as a possible alternative to the dark matter or MOND hypothesis. We will find a solution for the baryonic Tully-Fischer relation: $M_{b} = A v_{f}^4 \iff A = \left[a_{0}G \right]^{-1}$ with $a_{0} = \frac{cH_{0}}{2\pi}$, where $H_{0}$ is the Hubble constant at present Time $t_{0}$ and $M_{b}$, $G$ and $c$ are the galaxy baryonic mass, gravitational constant and constant speed of light in vacuum respectively. Also we will find the mass discrepancy-acceleration relation, thus obtaining a possible solution for each of the three laws of rotationally supported galaxies proposed in ({\cite{McGaugh}},{\cite{McGaugh1}}).

This work aimed to study the spatial variability of particulate matter deposition flux in urban-industrial environments. The main objective was to identify areas with higher deposition flux and associate the variability with climatological variables and with possible surrounding emitting sources. The method for collecting the deposited particles was based on the standard NF X 43-007. Sampling for particulate matter took place between April 2015 and February 2016, through seven sampling campaigns. Maps of the spatial dispersion for the particulate matter were obtained through statistics and geostatistics techniques. Elemental identification by scanning electron microscopy (SEM) was also used in two sampling campaigns. The results show that the sampling campaigns that took place during hot and dry periods, 2nd and 3rd, present higher deposition flux: 2.04 g/(m2 x month) and 1.72 g/(m2 x month), respectively. Lower deposition fluxes were registered in the 6th and 7th campaigns: 0.23 g/(m2 x month) and 0.24 g/(m2 x month), respectively. It was also observed a recurrent high deposition at specific sampling points which may be due to both the nearby road traffic and the presence of chimneys. SEM analysis allowed to associate repetitive element deposition, at the same sampling point, to the same emitting source.

The study of the concentrations and effects of fine particulate matter in urban areas have been of great interest to researchers in recent times. This is due to the acknowledgment of the far-reaching impacts of fine particulate matter on public health. Remote sensing data have been used to monitor the trend of concentrations of particulate matter by deriving aerosol optical depth (AOD) from satellite images. The Center for International Earth Science Information Network (CIESIN) has released the second version of its global PM_2.5 data with improvement in spatial resolution. This paper revisits the study of spatial and temporal variations in particulate matter in Saudi Arabia by exploring the cluster analysis of the new data. Cluster analysis of the PM_2.5 values of Saudi cities is performed by using Anselin local Moran’s I statistic. Also, the analysis is carried out at the regional level by using self-organizing map (SOM). The results show an increasing trend in the concentrations of particulate matter in Saudi Arabia, especially in some selected urban areas. The eastern and south-western parts of the Kingdom have significantly clustering high values. Some of the PM2.5 values have passed the threshold indicated by the World Health Organization (WHO) standard and targets posing health risks to Saudi urban population.

Since general relativity (GR) has already established that matter can simultaneously have two different values of mass depending on its context, we argue that the missing mass attributed to non-baryonic dark matter (DM) actually obtains because there are two different values of mass for the baryonic matter involved. The globally obtained "dynamical mass'' of baryonic matter can be understood as a small perturbation to a background spacetime metric even though it's much larger than the locally obtained "proper mass". Having successfully fit the SCP Union2.1 SN Ia data without accelerating expansion or a cosmological constant, we employ the same ansatz to compute dynamical mass from proper mass and explain galactic rotation curves (THINGS data), the mass profiles of X-ray clusters (ROSAT and ASCA data) and the angular power spectrum of the cosmic microwave background (Planck 2015 data) without DM. We compare our fits to modified Newtonian dynamics (MOND), metric skew-tensor gravity (MSTG) and scalar-tensor-vector gravity (STVG) for each data set, respectively, since these modified gravity programs are known to generate good fits to these data. Overall, we find our fits to be comparable to those of MOND, MSTG and STVG. While this favorable comparison does not establish the validity of our proposition, it does provide confidence in using the fits to pursue an underlying action. Indeed, the functional form of our ansatz reveals an interesting structure in these fits.

The basic helix loop helix (bHLH) transcription factors play crucial roles in plant growth, development, and stress responses. However, their identification and insight understanding in rubber trees remain largely uncovered. In this study, the bHLH gene family was explored and characterized in rubber trees using systematic bioinformatics approaches. In total, 180 bHLH genes were identified in the rubber tree genome, distributed unevenly across 18 chromosomes, and phylogenetic analysis classified these genes into 23 distinct subfamilies. Promoter regions revealed a high density of cis-elements responsive to light and hormones. Enrichment analysis indicated involvement in numerous biological processes, including growth, development, hormone responses, abiotic stress resistance, and secondary metabolite biosynthesis. Protein interaction network analysis identified extensive interactions between HbbHLH genes and other functional genes, forming key clusters related to iron homeostasis, plant growth, and stomatal development. Expression profiling of HbbHLH genes have demonstrated varied responses to endogenous and environmental changes. RT-qPCR of eleven HbbHLH genes in different tissues and under ethylene, jasmonic acid, and cold treatments revealed tissue-specific expression patterns and significant responses to these stimuli, highlighting the roles of these genes in hormone and cold stress responses. These findings establish a framework for exploring the molecular functions of bHLH transcription factors in rubber trees.

Background/Objectives: Dental implants have become a cornerstone of restorative dentistry, providing a long-lasting method for tooth replacement. The level of osseointegration has a big impact on the biomechanical stability at the bone-implant contact (BIC), which determines how long these implants will work. However, the exact consequences of changing osseointegration levels on different implant designs, especially in bones with variable densities, are not well known. Three short dental implants were tested in this study: BioMet 3iT3, Straumann® Standard Plus Short Regular Neck (SPS-RN), and Straumann® Standard Plus Short-Wide Neck (SPS-WN). 3D finite element analysis (FEA) was used to look at how well they worked biomechanically. This paper tests the implants at four stages of osseointegration: 25%, 50%, 75%, and 100% in both high-density (Bone Type III) and low-density (Bone Type IV) cancellous bone. It also created and examined realistic CAD models under static occlusal loading conditions to assess stress distribution and major strains at the bone-implant contact.; Results: The study discovered that as osteointegration increases, von Mises stress and principal strains go down significantly for all implant types. The SPS-WN implant had the lowest strain values, especially for bone with low density. These reductions demonstrate increased mechanical stability as the bone-implant inter-face becomes more capable of dispersing mechanical stresses, minimizing the potential for localized deformation and bone resorption.; Conclusions: The results highlight the importance of achieving optimum osseointegration to reduce mechanical stress and increase the lifespan of dental implants. The SPS-WN type implant performed better in biomechanical tests than the others, especially when bone conditions were not ideal. This makes it a great choice for clinical applications that need long-term implant success.

A number of regolith-hosted REE occurrences have recently been discovered in the Esperance region in southern Western Australia. This paper summarizes major characteristics of the REE mineralization and discusses contributing factors and potential controls. The main aim is to explain why there is a lack of highly sought-after ion-adsorption clay type REE deposits across the region despite the presence of the regolith-hosted REE mineralization on a regional scale. Local mineralization mostly occurs as continuous flat-lying enrichment “blankets” within the residual regolith developed over Archaean–Proterozoic granite gneisses and granitoids with elevated REE content. The enriched horizon is commonly located in the lower saprolite and saprock and is accompanied by an overlying REE-depleted zone. This distribution pattern, together with the data on HREE fractionation and the presence of the supergene REE minerals, indicate chemogenic type enrichment formed by supergene REE mobilization into groundwater, downward transport and accumulation in the lower part of the weathering profile. Residual REE accumulation processes due to bulk rock volume and mass reduction during weathering also contribute to mineralization. It is proposed that climate and groundwater chemistry are the critical controls on the distribution of REEs in the weathering profile and on their speciation in the enrichment zone. Cenozoic aridification of climate in southwest Australia heavily overprinted pre-existing REE distributions in the weathering profile. Acidic (pH &lt;4), highly saline groundwaters intensely leached away any relatively weakly bound, adsorbed or colloidal REE forms, moving them downward. Dissolved RREs precipitated as secondary phosphates in neutral to alkaline environment at lower Eh near the base of the weathering profile forming the supergene enrichment zone. Low denudation rates, characteristic of areas of low relief under the arid climate, are favorable for the preservation of the existing weathering profiles with REE mineralization.

The purpose of this finite element analysis (FEA) was to evaluate the stress experienced by both the prosthetic components and the bone in relation to varying cement thicknesses ranging from 20 to 60 μm, utilized in the attachment of a zirconia crown on a conometric cap. The study focused on two distinct types of implants (Cyroth and TAC, AoN Implants, Grisignano di Zocco, Italy) featuring a Morse cone connection. Detailed three-dimensional (3D) models were created to repre-sent the bone structure (cortical and trabecular) and the prosthetic components, encompassing the crown, cement, cap, abutment, and the implant. The two implants were placed in a 1.5 mm sub-crestal position and subjected to an inclined load of 200 N at 45° on the crown. The results re-vealed that an increase in cement thickness resulted in a reduction of von Mises stress on the cor-tical bone for both Cyroth and TAC implants, while the decrease in stress on the trabecular bone was relatively less pronounced. However, the TAC implant exhibited a higher stress field and de-formation in the apical area compared to the Cyroth implant. In summary, this study investigated the impact of cement thickness on stress transmission across prosthetic components and peri-implant tissues by means of FEA analysis, indicating that the 60 μm cement layer manifested higher stress values nearing the material strength limit.

In this paper, a multi-patch weakly singular isogeometric boundary element method (WSIGABEM) for two-dimensional elastostatics is proposed. Since the method based on the weakly singular boundary integral equation, the quadrature techniques, dedicated for the weakly singular and regular integrals, are applied in the method. A new formula for the generation of collocation points is suggested to take the full advantage of the multi-patch technique. The generated collo-cation points are essentially inside the patches without any correction. If the boundary conditions are assumed to be continuous in every patch, no collocation point lies on the discontinuous boundaries, thus simplifying the implementation. The multi-patch WSIGABEM is verified by the simple examples with analytical solutions. The feature of the present multi-patch WSIGABEM is investigated by the comparison with the traditional IGABEM. Furthermore, the combination of the present multi-patch WSIGABEM and the particle swarm optimization algorithm results in a shape optimization method in two-dimensional elastostatics. By changing some specific control points and their weights, the shape optimizations of the fillet corner, the spanner and the arch bridge are verified to be effective.

Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

Road-embedded inductive power transfer (IPT) systems have the potential to accelerate the electrification of the transportation sector. For these systems to be economically viable however, they need to have a similar durability and lifespan compared to that of asphalt roads. One area that has lacked investigation is thermally induced stresses in a primary IPT pad, which is caused by the increase in temperature of the pad when it is energized and the differing thermal expansion of the materials within. This paper presents an experimental and a finite-element based methodology for investigating the thermal-mechanical behaviour of a ¼-scale double-D pad, which was energized while suspended in air, as well as energized when embedded in pavement. A focus was placed on the measurement and prediction of strains in the magnetic ferrite cores because of their brittleness. Ferrite strains were measured using a combination of resistive strain gauges and non-metallic Fibre Bragg Grating (FBG) sensors. Coupled electromagnetic-thermal-structural simulations were conducted to predict temperature and strains in the system, with temperature-dependent properties obtained through physical testing. At an ambient temperature of 50°C, the temperature in the middle of the copper litz wire coil was predicted to be 100°C in both the suspended and embedded case. There was excellent correlation to experimental results, with a difference of less than 10% for most temperature measurements. When energized, the pad was predicted to experience an upward bow due to its temperature rise, resulting bending strains in the ferrite cores. At an ambient temperature of 50°C, maximum tensile strain in the ferrites of the embedded pad was measured to be 62 microstrain (με), with a root-mean square error that was 18 με across three sensors. The experimental and validated numerical methodology can be applied to full-scale operational IPT pads to analyse and improve their thermal-mechanical performance.

This research endeavors to illuminate the path toward efficient and optimized propeller design by delving into the realm of aerodynamics. Propellers, as vital mechanical marvels, constitute the core of numerous propulsion systems, spanning from aircraft and marine vessels to wind turbines. The pursuit of enhanced propeller efficiency and performance holds paramount importance in industries where propulsion assumes a critical role, underscoring the indispensable need for a profound understanding of aerodynamics. Through meticulously crafted theoretical insights and their practical applications, this study embarks on a journey into the fascinating realm of propeller aerodynamics. While the paper primarily addresses the aerodynamic aspects of propeller design and optimization, it serves as a foundational guide for those seeking to comprehend the intricacies of propeller engineering.The research journey commences with an in-depth exploration of the fundamental principles governing propeller performance. It unveils the intricate dynamics of airflow surrounding propeller blades, shedding light on their proficiency in generating thrust, lift, and torque. The bedrock of the theoretical insights is a comprehensive analysis encompassing airfoil profiles, blade geometry, and the underlying principles of blade element theory. In navigating the ensuing pages, the study embarks on the task of demystifying the intricate methods and calculations that propel the design and optimization of propellers. Leveraging cutting-edge methodologies, the research systematically assesses the aerodynamic characteristics of propellers across various operational conditions. These invaluable insights empower the tailoring of propeller designs with precision, aligning them seamlessly with specific performance objectives. The aim is not only to impart a comprehensive understanding of propeller aerodynamics but also to provide actionable insights for engineers and researchers striving to enhance propeller efficiency. This research endeavor serves as a guiding light for both propeller enthusiasts and professionals alike. It not only enriches the broader discourse on propeller technology but also equips readers with the requisite knowledge and tools to embark on their own quests for optimized propeller design. As propulsion technologies continue their evolution, the steadfast principles elucidated herein will persist, guiding future innovations and advancements in the realm of propeller engineering. This paper serves as a profound resource, offering new researchers a comprehensive understanding of propellers and their intricate design processes.

In recent years, there has been a growing interest in the preoperative modeling of fluid-structure interaction in the treatment of cerebral aneurysms. In this study, we investigate two cases involving laminar incompressible fluid flow interacting with hyperelastic materials (a vertical flap and aneurysm walls) under the effect of fluid flow. We present a finite element method (FEM) for these prototypical two-dimensional ($2D$) configurations, taking into account the complex flows and deformation of the variant's structure models. We use an Arbitrary Lagrangian-Eulerian (ALE) formulation in a continuum, fully monolithic coupled way, and discretize the fluid and solid domains using the quadratic LBB stable $P_2P_1$ finite element pair to approximate the displacement, velocity, and pressure spaces independently. The resulting discretized form of the nonlinear algebraic system is linearized using a variant of Newton's procedure, and the Jacobian matrices are approximated via the divided difference method. The resulting linear systems are solved using a direct solver MUMPS. We evaluate hydrodynamic forces such as drag and lift coefficients for nonlinear elastic material models, including Saint-Venant Kirchoff, Neo-Hookean, and Mooney-Rivlin (2 parameters) separately. To gain more physical insight into the problem, we verify the computed results by comparing the velocity, viscosity, and pressure fields. Our aim is to qualitatively analyze the changes in the mechanics of the wall behavior of the elasticity of the flap vs. the complexity of deformation, interface, details for prototypical flow situations, corresponding displacement, and deformation. We also provide a physical interpretation of blood flow magnitude and basic hemodynamic phenomena of wall shear stresses (WSS) in aneurysma and the range of deformation. Overall, this study presents a comprehensive approach to modeling fluid-structure interaction in cerebral aneurysms, which could help in the development of more effective treatment strategies.

How complex morphological patterns form is an intriguing question in developmental biology. However, the mechanisms that generate complex patterns remain largely unknown. Here we sought to identify the genetic mechanisms that regulate the tan (t) gene in a multi-spotted pigmentation pattern on the abdomen and wings of Drosophila guttifera. Previously, we showed that yellow (y) gene expression completely prefigures the abdominal [1] and wing [2] pigment patterns of this species. In the current study, we demonstrate that the t gene is co-expressed with the y gene in nearly identical patterns, both transcripts foreshadowing the adult abdominal and wing melanin spot patterns. We identified cis-regulatory modules (CRMs) of t, one of which drives reporter expression in six longitudinal rows of spots on the developing pupal abdomen, while the second CRM activates the reporter gene in a spotted wing pattern. Comparing the abdominal spot CRMs of y and t, we found a similar composition of putative transcription factor binding sites that are thought to regulate the complex expression patterns of both terminal pigmentation genes y and t. In contrast, the y and t wing spots appear to be regulated by distinct upstream factors. Our results suggest that the D. guttifera abdominal and wing melanin spot patterns have been established through the co-regulation of y and t, shedding light on how complex morphological traits may be regulated through the parallel coordination of downstream target genes.

We present a finite element model updating technique for soil-structure system identification of the Millikan Library building using the seismic data recorded during the 2002 Yorba Linda earthquake. A detailed finite element (FE) model of the Millikan Library building is developed in OpenSees and updated using a sequential Bayesian estimation approach for joint parameter and input identification. A two-step system identification approach is devised. First, the fixed-base structural model is updated to estimate the structural model parameters (including effective elastic modulus of structural components, distributed floor mass, and Rayleigh damping parameters) and some uncertain components of the foundation-level motion. Then, the identified structural model is used for soil-structure model updating wherein the Rayleigh damping parameters, the stiffness and viscosity of the soil subsystem (modeled using a substructure approach), and the foundation input motions (FIMs) are estimated. The identified model parameters are compared with state-of-practice recommendations. While a specific application is made for the Millikan Library, the present work offers a framework for integrating large-scale FE models with measurement data for model inversion. By utilizing this framework for different civil structures and earthquake records, key structural model parameters can be estimated from the real-world recorded data, which can subsequently be used for assessing and improving, as necessary, state-of-the-art seismic analysis and structural modeling techniques. This paper presents an effort towards using real-world measurements for large-scale FE model updating in the soil and structure, uniform soil time domain for joint parameter and input estimation, and thus paves the way for future applications in system identification, health monitoring and diagnosis of civil structures.

Ischemic stroke is one of the most disabling diseases and a leading cause of death globally. Despite advances in medical care, the global burden of stroke continues to grow, as no effective treatments to limit or reverse ischemic injury to the brain are available. However, recent preclinical findings have revealed the potential role of transient receptor potential cation 6 (TRPC6) channels as endogenous protectors of neuronal tissue. Activating TRPC6 in various cerebral ischemia models has been found to prevent neuronal death, whereas blocking TRPC6 enhances sensitivity to ischemia. Evidence has shown that Ca2+ influx through TRPC6 activates cAMP response element-binding protein (CREB), an important transcription factor linked to neuronal survival. Additionally, TRPC6 activation may counter excitotoxic damage resulting from glutamate release by attenuating the activity of NMDA receptors of neurons by posttranslational means. Unresolved though, are the roles of TRPC6 channels in non-neuronal cells such as astrocytes and endothelial cells. Moreover, TRPC6 channels may have detrimental effects on the blood-brain barrier, although their exact role in neurovascular coupling requires further investigation. This review discusses evidence-based cell-specific aspects of TRPC6 in the brain to assess the potential targets for ischemic stroke management.

The paper is dedicated to the topical problem of examining permafrost state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we propose and scientifically substantiate a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings and constructions.

Fire is a significant threat to human life and civil infrastructures. Builders and architects are hankering for safer and sustainable alternatives of concrete that do not compromise with their design intent or fire safety requirements. The aim of the present work is to improve the residual compressive performance of concrete in the post-fire exposure, by incorporating by-products from urban residues. Based on sustainability and circular economy motivations, the attention is focused on rubber tire fly ash, aged brick powder, and plastic (PET) bottle residuals used as partial sand replacement. The selected by-products from urban residues are used for the preparation of Cement-Based Composites (CBCs) in two different proportions (10 % and 15 %). The thermal CBC behaviour is thus investigated under realistic fire scenarios (i.e., Direct Flame (DF) for 1 hour (1h)), by following the ISO 834 standard provisions, but necessarily resulting in non-uniform thermal exposure for the cubic specimens. The actual thermal exposure is further explored with a Finite Element (FE) model, giving evidence of thermal boundaries effects. The post-fire residual compressive strength of heated concrete and CBC samples is hence experimentally derived, and compared to unheated specimens in ambient conditions. From the experimental study, the enhanced post-fire performance of CBCs with PET bottle residual is generally found superior to other CBCs or concrete. The structure-property relation is also established, with the support of Scanning Electron Microscopy (SEM) micrographs. Based on existing empirical models of literature for the prediction of the compressive or residual compressive strength of standard concrete, newly developed empirical relations for both concrete and CBCs are assessed.

Modeling fluid flow in three-dimensional (3D) Discrete Fracture Networks (DFNs) is of relevance in many engineering applications, such as hydraulic fracturing, oil/gas production, geothermal energy extraction, nuclear waste disposal and CO₂ sequestration. A new Boundary Element Method (BEM) technique with discontinuous quadratic elements and a parallel Domain Decomposition Method (DDM) is presented herein for the simulation of the steady-state fluid flow in 3D DFN systems with wellbores, consisting of planar fractures having arbitrary properties and wellbore trajectories. Numerical examples characterized by DFNs of increasing complexity are investigated to evaluate the accuracy and efficiency of the presented technique. The results show that accurate solutions can be obtained with less nodes than with mesh-based methods (e.g. Finite Element Method). In addition, the DDM algorithm used provides a quite fast convergence. The simulation results of the fluid flow around intersections among traces (linear intersections between fractures), intersections between traces and a fracture boundaries, and wellbore intersections is accurate. Source code is available at : https://github.com/BinWang0213/PyDFN3D.

This study presents a new form of velocity distribution in laminar liquid flow in rectangular microchannels using the eigenfunction expansion technique. Darcy friction factor and Poiseuille number are also obtained analytically. Due to the symmetry of the solutions, the effects of changing the aspect ratio from 0 to ∞ are also discussed. Using finite element method (FEM), the obtained analytical results are further compared with the 3D numerical simulations for the rectangular microchannels with different range of aspect ratio and pressure gradient, and excellent agreements were found. These findings provide additional insights in interpreting the results of the pressure-driven flows in finite aspect ratio microchannels, in which very precise comparison with the macroscale theory is crucial.

The amount and spatial distribution of foliage in a tree canopy have fundamental functions in ecosystems as they affect energy and mass fluxes through photosynthesis and transpiration. They are usually described by the Leaf Area Index (LAI) and the Leaf Area Density (LAD), which can be measured through a variety of methods, including voxel-based methods applied to LiDAR point clouds. A theoretical study recently compared the numerical errors arising from different voxel-based estimation methods for Plant Area Density (PAD) based on Beer’s law-based, contact frequency and Maximum-Likelihood Estimation, showing that the bias-corrected Maximum Likelihood Estimator was theoretically the most efficient. However, this earlier study i) ignored wood volumes; ii) neglected vegetation clumping inside the voxel; iii) ignored instrument characteristics in terms of effective footprint, iv) was limited to a single viewpoint. In practice, retrieving LAD from PAD is not straightforward, vegetation is not randomly distributed in volumes of interest, beams are divergent and forestry plots are usually sampled from more than one viewpoint, to mitigate the effect of occlusion. In the present short communication, we extend the previous efficient formulation to actual field conditions to i) account for the presence of both wood volumes and wood hits, ii) rigorously include correction terms for vegetation and instrument characteristics, iii) integrate multiview data. A numerical comparison with other methods commonly used to combine information from different viewpoints led to error reduction, especially in poorly-explored volumes, which are frequent in actual canopies. Beyond its concision, completeness and efficiency, this new formulation -which can be applied to multiview TLS, but also UAV LiDAR scanning - can help reducing errors in LAD estimation.

Cardiovascular risk factors (CRFs) such as hypertension, high cholesterol, and diabetes are increasingly implicated in cognitive decline and cerebral small vessel disease (cSVD). White matter hyperintensities (WMH), a hallmark of cSVD, are strongly linked to cognitive impairment, but their underlying mechanisms remain unclear. Blood-brain barrier (BBB) dysfunction has been proposed as a potential contributor to WMH development. This study aimed to explore the relationships between CRFs, BBB integrity, and WMH burden. We analyzed 155 participants from the Biomarkers and Cognition Study, Singapore, assessing CRFs through blood tests for glucose and lipid profiles, alongside blood pressure measurements. WMH volume was quantified using MRI, and an in vitro assay evaluated the impact of plasma on BBB integrity using human brain microvascular endothelial cells. Results showed that plasma from participants with higher WMH burden correlated with increased BBB disruption, which was further associated with higher blood pressure, elevated blood glucose, and lipid levels. Both periventricular and subcortical WMH were linked to BBB disruption. These findings suggest that CRFs contribute to BBB dysfunction, promoting WMH development and cognitive decline in cSVD. Further research is needed to clarify the precise mechanisms driving these associations.

HTLV-1-associated myelopathy/tropical spastic paraparesis (HAM/TSP) is a chronic progressive neurological disorder and shares many radiological and clinical features with other more prevalent myelopathies. Here, we quantified spinal cord and brain volumes in adults with HAM/TSP in comparison with healthy volunteers (HVs) and participants diagnosed with multiple sclerosis (MS). Clinical disability and MRI were assessed in 24 HVs, 43 HAM/TSP, and 46 MS participants. Spinal cord cross-sectional area (SCCSA) and brain tissue volumes were measured and compared. HAM/TSP participants had significantly lower SCCSA at C2-3 (54.0±8 mm2), C4-5 (57.8±8 mm2), and T4-9 (22.7±4 mm2) and significantly elevated brain white matter hyperintensity (WMH) fraction (0.004±0.008) was compared to HVs (C2-3: 69.4±8 mm2, C4-5: 75.1±9 mm2, T4-9: 34.1±4 mm2; all p &lt; 0.0001; and WMH: 0.0004±0.0007; p &lt; 0.001). In HAM/TSP, SCCSA at all levels but not WMH showed the significant correlation with clinical disability scores. Brain white matter hyperintensities in HAM/TSP, therefore, may not be related to clinical disability. SCCSA and WMH in our limited MS cohort were higher than the HAM/TSP cohort (67.6±8 mm2, 72.7±9 mm2, 33.4±5 mm2; p &lt; 0.0001). Principal component analysis suggested that SCCSA and WMH may be used to differentiated HAM/TSP from MS. Understanding these differences may help establish early diagnostic criteria for HAM/TSP patients.

The spin-torsion theory is a gauge theory approach to gravity that expands upon Einstein's general relativity (GR) by incorporating the spin of microparticles. In this study, we further develop the spin-torsion theory to examine spherically symmetric and static gravitational systems that involve free-falling macroscopic particles. We posit that the quantum spin of macroscopic matter becomes noteworthy on cosmic scales. We further assume that the Dirac spinor and Dirac equation adequately capture all essential physical characteristics of the particles and their associated processes. A crucial aspect of our approach involves substituting the constant mass in the Dirac equation with a scale function, allowing us to establish a connection between quantum effects and the scale of gravitational systems. This mechanism ensures that the quantum effect of macroscopic matter is scale-dependent and diminishes locally, a phenomenon not observed in microparticles. For any given matter density distribution, our theory predicts an additional quantum term, the quantum potential energy (QPE), within the mass expression. QPE induces time dilation, distance contraction, and thus mimics a gravitational well. When applied to cosmology, our theory yields a static cosmological model. The QPE serves as a counterpart to the cosmological constant introduced by Einstein to balance gravity in his static cosmological model. The QPE also offers a plausible explanation for the origin of the Hubble redshift (traditionally attributed to the universe's expansion). The predicted luminosity distance-redshift relation aligns remarkably well with SNe Ia data from the cosmological sample of SNe Ia. In the context of galaxies, QPE functions as the equivalent of dark matter. The predicted circular velocities align well with the rotation curve data from the SPARC (Spitzer Photometry and Accurate Rotation Curves database) sample. Importantly, our conclusions in this paper are reached through a conventional approach, with the sole assumption of the quantum effects of macroscopic matter on large scales, without the need for additional modifications or assumptions.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

The star matter composed of nucleons deep inside the compact star like a neutron star is believed to be very dense and various new types of concepts and physical phenomena due to the nontrivial strong correlations are naturally expected. Peudo-conformality in dense star matter has been discussed recently assuming the hidden underlying scale symmetry, which is partly supported by the recent discussions of infrared conformal window of QCD. It is found that the appearance of dilaton and the dilatonic mean field calculation of nucleonic matter lead to the density independent nucleon mass at higher density regime than normal nuclear matter density. Non-vanishing constant nucleon mass can be considered as a chiral invariant mass of the parity doublet model, in which the chiral symmetry is manifested even in the massive nucleon sector provided with a parity doubling. In this paper we will discuss how the chiral and scale symmetry are correlated to lead the parity doublet symmetry inside the core of the compact star. A simple schematic model is adopted. The star matter at T=0 is basically composed of the nucleons. As a first approximation, they can be treated as free fermions with the effective mass filled up to fermi surface. There is a nontrivial feature due to the interplay between vector meson and nucleon(or equivalently dilaton, χ). The trace of energy momentum tensor approaches density independent, the pseudo-conformal phase. Local fluctuations inside the star matter will be travelling with the speed of sound which depends on the equation of state. In the pseudo-conformal phase, the speed of sound approaches to the conformal velocity for the scale symmetric matter, vc=13c. The excitations of the parity doublets in the compact star matter as an emerging phenomena in pseudo-conformal phase will be discussed in connection to the chiral symmetry. The possible implication on the corespondence of hadrons to quark degrees of freedom will be briefly discussed.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

The human body contains 60-70% of water, depending on age. As a body fluid, it is not only a medium in which physical and chemical processes take place, but it is also one of the active mediators. Water is the richest substance with non-covalent hydrogen bonds. Water molecules, by themselves (in vacuum), are diamagnetic, but when organized into clusters, become diamagnetic or paramagnetic. Also, biomolecules (DNA, collagen, clathrin, and other proteins) have non-covalent hydrogen bonds in their structure. The interaction, as well as signal transmission, between water and biomolecules is achieved through the vibrations of covalent and non-covalent hydrogen bonds, which determine the state and dynamics of conformational changes of biomolecules. Disruptive conformational changes of biomolecules, cells, and tissues lead to their dysfunctionality, so they are a frequent cause of many disorders and diseases. For example, the rearrangement of hydrogen bonding due to mitochondrial disease mutation in cytochrome bc1 disturbs heme bH redox potential and spin state. In order to prevent and repair the dysfunctional conformational changes, a liquid substance was developed based on the second derivative of the C₆₀ molecule (SD-C₆₀), which has classical and quantum properties. Characterization of SD-C₆₀ by UV-VIS-NIR, FTIR, TEM, and AFM/MFM was done and it is shown that SD-C₆₀ water layers generate vibrations with near-zero phase dispersion which are transmitted through the Fibonacci’s water chains to biomolecules. In comparison to previously published SD-C₆₀ derivate (3HFWC, size until 10 nm, and 1-5 water layers), improved formulation (3HFWC-W, size 10-25 nm, and 6-9 water layers) showed multiplied cytotoxic activity against melanoma cell lines of different aggressiveness. Apart from this, the mode of action was preserved and based on induction of senescence rather than cell death. Importantly, high selectivity toward malignant phenotype was detected. Observed effects can be ascribed to a machinery of hydrogen bonds, which are generated in SD-C₆₀ and transmitted through water to biomolecules. This approach may open a new field in science and healthcare - a “water-based nanomedicine”.

In this work, we examine the deflection angle of black hole in effective loop quantum gravity in non-plasma medium via the geometrical technique of Gibbons and Werner in weak field limits. For this, we attain the optical metric and calculate the Gaussian optical curvature and then we apply the Gauss-Bonnet theorem. We also study the influence of the plasma and dark matter mediums on the deflection angle. Further, we obtain the deflection angle by using Keeton and Petters method. We also calculate the Hawking temperature via Gauss-Bonnet theorem. In addition, we determine the fermionic greybody bounds. Moreover, we discuss the graphical behaviour of the bending angle and bounds on the greybody factor. We also examine that the results obtained for the black hole in effective loop quantum gravity are reduces to the Schwarzschild black hole solutions when dimensionless non-negative parameter $A_{\lambda}=0$.

Every day around 93% of children under the age of 15 (1.8 billion children) breathe outdoor air that is so polluted it puts their health and development at serious risk. Due to the pandemic, however, ventilation of buildings using outdoor air has become an important safety technique to prevent the spread of COVID-19. With the mounting ev-idence suggesting that air pollution is impactful to human health and educational out-comes, this contradictory guidance may be problematic in schools with higher air pol-lution levels, but keeping kids COVID-19 free and in school to receive their education is now more pressing than ever. To understand if all schools in an urban area are ex-posed to similar outdoor air quality and if school infrastructure protects children equally indoors, we installed research grade sensors to observe PM2.5 concentrations in indoor and outdoor settings to understand how unequal exposure to indoor and out-door air pollution impacts indoor air quality among high- and low-income schools in Salt Lake City, Utah. Based on this approach, we found that during atmospheric inver-sions and dust events, there was a lag ranging between 35 to 73 minutes for the out-door PM2.5 concentrations to follow a similar temporal pattern as the indoor PM2.5. This lag has policy and health implications and may help to explain the rising concerns re-garding reduced educational outcomes related to air pollution in urban areas. These data and resulting analysis show that poor air quality may impact school settings, and the potential implications with respect to environmental inequality.

HU is the Hypergeometrical Universe Theory (HU)[1-8], proposed in 2006, where the Universe is a Lightspeed Expanding Hyperspherical Hypersurface and Gravitation is an absolute-velocity-dependent, epoch-dependent force. Here we introduce the Big Pop Cosmogenesis and show our calculations associated with the Equation of State of the Universe. This article is the first in a series of articles[9-22] supporting the paradigm shift.

This study presents a methodology to reveal traces of viral particles, as aerosol with known chemical and molecular structure, in a sample by means of photon and electron interactions. The method is based on Monte Carlo simulations and on the analysis of photon-electron fluxes-spectra through energy channels counts as a function of different aerosol viral concentrations in the air sample and looking at the peculiar photon/electron interactions with the potential abnormal atomic hydrogen (H), oxygen (O), carbon (C), and phosphorus (P) compositions present in the air sample as a function of living and nonliving matter with PO4 group RNA/DNA strands in a cluster configuration.

Depending on the characteristics of the industrial area, toxicity evaluation of human body, risk assessment and health impact assessment may directly cause cancer due to air pollution. Environmental data collection is from August 2018 to January 31, 2019, and the average, minimum, and maximum values of air pollution data respectively. According to the global data on global trends using the Big Data, high blood pressure is confirmed at 33rd place in the world, and myocardial infarction among the environmental diseases is confirmed to be lower than Korea. Disease that occurred in Jeolla province industrial complex considering the characteristics of our country was identified as representative. Air pollutants are considered to be the causes of allergic diseases in Korea. PM10 was found to be higher than the control area (28.8804348 (㎍ / ㎥), 31.7065217 (㎍ / ㎥) and 32.8532609 (㎍ / ㎥). The mean concentrations of PM2.5 in the middle and high exposure areas were lower than those of the control areas, but the highest in the intermediate exposure areas was 16.5978261 (㎍ / ㎥), 16.1086957 (㎍ / ㎥) and 17.1847826 (㎍ / ㎥) respectively. The relationship between the major variables of environmental exposure in Yeosu was confirmed to be correlated with high blood pressure, chronic obstructive pulmonary disease (COPD), bronchitis, cerebrovascular, diabetes, thyroid disease, sinus infection, anemia and pneumonia.