The application of photopolymerization 3D printing technology in the field of piezoelectric ceramics can achieve high precision, customization, and personalized design of piezoelectric ceramics, providing a better technical means for the fine processing of ceramic materials. We have studied the preparation of PZT piezoelectric ceramic 3D printing slurry, as well as the analysis of forming errors of printed green bodies, debinding process, and sintering. We successfully printed and sintered various porous honeycomb structures of D-type and G-type using a PZT slurry with a solid content of 55 wt.%.

Considering that the electric refrigeration temperature range of 0.94BNT-0.06BT ceramic materials is 100~140˚C, the electric refrigeration performance of the 0.94BNT-0.06BT ceramic material system was modified by LiNbO3 doping to reduce the cooling temperature. As a result, the refrigeration temperature range of the 0.94BNT-0.06BT ceramic material system was lowered to 25~80 ˚C, achieving its cooling effect near room temperature, and in this temperature range, the adiabatic temperature changes ∆T>0.6K.

The beneficial effects of Lanthanide incorporation into 0.94Na0.5Bi0.5TiO3-0.06BaTiO3 (BNT-BT) matrix on its functional properties were investigated. The conventional solid-state method was used for synthesizing samples. The structural refinement revealed that all samples crystallized in R3c rhombohedral symmetry. Raman spectroscopy study was carried out using green laser excitation and revealed that no clear perceptible variation in frequency is observed. Dielectric measurements unveiled that the introduction of rare earth obstructed the depolarization temperature promoted in BNT-BT with decreasing the diffusive phase transition with increasing the lanthanide size. Only Dysprosium addition showed comparable diffusion constant and dielectric behavior as the unmodified composition. Further, the comparison of the obtained ferroelectric hysteresis and strain-electric field loops revealed that only Dy-phase exhibited interesting properties comparing parent composition. In addition, the incorporation of lanthanides Ln3+ into the BNT-BT matrix led to the development of luminescence characteristics in the visible and near infrared regions, depending on the excitation wavelengths. The simultaneous occurrence of photoluminescence and ferroelectric/piezoelectric properties opens up possibilities for BNT-BT-Ln to exhibit multifunctionality in a wide range of applications.Keywords: Sodium Bismuth Titanate; structural refinement; dielectric properties; ferroelectric properties; piezoelectric properties; Photoluminescence.

The effects of the dielectric constant of the powder phase on lead zirconate titanate (PZT)/PZT sol-gel composite films were investigated to tailor their electrical properties. Three types of PZT powders were used to fabricate three different PZT/PZT sol-gel composite films. The PZT powders had the same electromechanical coupling coefficient but different relative dielectric constants. The PZT/PZT films were fabricated on a 3 mm-thick titanium substrate using an automatic spray coating system, and their properties were investigated. The relative dielectric constants of the PZT/PZT films were successfully controlled by tailoring the properties of the PZT powder phase. However, the piezoelectric constants showed a tendency different to those of the raw powders, because of the poor poling degree. This was overcome by conducting poling at a high temperature.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

Energy harvesting is an emerging topic recently. This harvested energy is used to operate wireless sensors for different industrial monitoring and automation. To maximize the harvested energy in spinning systems, the harvester should vibrate at resonance for different spinning frequencies which can be achieved by active fitting. In this research, a novel methodology was developed by actively customizing the length of vibrating element beam to manipulate its natural frequency according to the spinning frequency. Different models were investigated numerically and experimentally to verify the proposed methodology. COMSOL Multiphysics software V5.1 was used to develop the numerical model, then and tip deformation and voltage difference results were benchmarked. The numerical model was verified experimentally by attaching a piezoelectric MIDE PPA 1021 which its vibrating length was varied by changing the supporting length from 0 mm to 12 mm to a spinning object having variable frequency from 0-200 Hz. It is found that the MIDE PPA 1021 beam vibrated at its resonance throughout the specified spinning frequencies. The proposed harvester can be applied in battery-free sensors being used in automotives, wind-mills blades, and rotating machinery.

With the depletion of natural resources, it has become a topic of great concern to address the unsustainable way of life. In this study, we investigate the use of piezoelectric material - to generate electricity in schools. The use of these piezoelectric materials in floor tiles could enable us to generate energy from the footsteps of the children in school. The goal is to be able to power lights and fans in classrooms and reduce the consumption of conventional electricity - produced through the combustion of coal and other natural resources. The primary method of research is to develop a prototype with different choices of material and configurations of piezoelectric transducers to maximize power generation in a typical school setting. The results showed that the energy generated from one step needs to be improved by a factor of 100 for a typical classroom to generate enough power for a light and a fan. The research found that current technology although promising is incapable of producing enough power via piezoelectric tiles in a school setting.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

This study fabricated piezoelectric fibers of polyvinylidene fluoride (PVDF) with graphene using near-field electrospinning (NFES) technology. A uniform experimental design table U*7 (7^4 ) was applied, considering weight percentage (1-13 wt%), distance between needle and disk collector (2.1-3.9 mm), and applied voltage (14.5-17.5 kV). We optimized the parameters using electrical property measurements and the Kriging response surface method. Adding 13 wt% graphene significantly improved electrical conductivity, increasing from 17.7 μS/cm for pure PVDF to 187.5 μS/cm. The fiber diameter decreased from 21.4 μm in PVDF/1% graphene to 9.1 μm in PVDF/13% graphene. Adding 5 wt% graphene increased the β-phase content by 6.9%, reaching 65.4% compared to pure PVDF fibers. Material characteristics were investigated using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), contact angle measurements, and tensile testing. Optimal parameters included 3.47 wt% graphene, yielding 15.82 mV voltage at 5 Hz and 5 N force (2.04 times pure PVDF). Force testing showed a sensitivity (S) of 7.67493 log(mV/N). Fibers were attached to electrodes for piezoelectric sensor applications. Results affirmed enhanced electrical conductivity, piezoelectric performance, and mechanical strength. The optimized piezoelectric sensor could be applied to measure physiological signals, such as attaching it to the throat under different conditions to measure the output voltage. The force-to-voltage conversion facilitated subsequent analysis.

Nowadays, the most advanced micromachined microphones on the market are based on a capacitive coupling principle. Capacitive micro-electro-mechanical systems-based (MEMS) microphones resemble their millimetric counterparts, both in function and in performances. The most advanced MEMS microphones reached a competitive level compared to commonly used measuring microphones in most of the key performance parameters except the acoustic overload point (AOP). In an effort to find a solution for measurement of high-level acoustic fields, microphones with piezoelectric coupling principle have been proposed. Such novel microphones exploit the piezoelectric effect of a thin layer of aluminum nitride, which is incorporated in their diaphragm structure. In these microphones fabricated with micromachining technology, no fixed electrode is necessary, in contrast to capacitive microphones. This specificity significantly simplifies both the design and the fabrication and opens the door for a new improvement of the acoustic overload point as well as harsh environmental applications. Several variations of piezoelectric structures together with an idea leading to electrically controlled sensitivity of MEMS piezoelectric microphone are discussed in the paper.

Piezoelectric cantilever harvesters have a large power output at their natural frequency, but in some applications the frequency of ambient vibrations is different from the harvester’s frequency and/or ambient vibrations are periodic with some harmonic components. To cope with these operating conditions harvesters with integrated trimming devices (ITDs) are proposed. Some prototypes are developed with the aid of an analytical model and tested with an impulsive method. Results show that a small trimming device can lower the main resonance frequency of a piezoelectric harvester of the same extent as a larger tip mass and moreover generates at high frequency a second resonance peak. A multi-physics numerical FE model is developed for predicting the generated power and for performing stress-strain analysis of harvesters with ITDs. The numerical model is validated on the basis of experimental results. Several configurations of ITDs are conceived and studied. Numerical results show that harvesters with ITDs are able to generate relevant power at two frequencies owing to the particular shape of the modes of vibration. The stress in the harvesters with ITDs is smaller than the stress in the harvester with a tip mass trimmed to the same frequency.

In this paper the possibility of harvesting energy from the vibrations of a plate is analyzed. The harvester takes the form of a cantilever dynamic vibration absorber equipped with a piezoelectric layer and tuned by means of a tip mass to the first mode of vibration of the plate. A mathematical model of the coupled system composed of the plate and the harvester is presented. The validity of the proposed harvester is proved by means of simulations carried out with the modal expansions approach. Simulation results highlighting the effect of harvester tuning and location are presented as well. Then the validity of the harvester is confirmed by experimental tests carried out both with a concentrated impulsive load and with a distributed pressure load. Simulations and experimental tests show that the cantilever piezoelectric dynamic vibration absorber generates open circuit voltage an order of magnitude larger than the one generated by the same piezoelectric layer when directly bonded to the plate surface.

A compact 2-DOF (two degrees of freedom) piezoelectric-driven platform for 3D cellular bio-assembly systems has been proposed based on “Z-shaped” flexure hinges. Multiple linear motions with high resolution both in x and y directions are achieved. The “Z-shaped” flexure hinges and the parallel-six-connecting-rods structure are utilized to obtain the lowest working stress while compared with other types of flexure hinges. In order to achieve the optimized structure, matrix-based compliance modeling (MCM) method and finite element method (FEM) are used to evaluate both the static and dynamic performances of the proposed 2-DOF piezoelectric-driven platform. Experimental results indicate that the maximum motion displacements for x stage and y stage are lx=17.65 μm and ly=15.45 μm, respectively. The step response time for x stage and y stage are tx=1.7 ms and ty =1.6 ms, respectively.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

This study presents the design and implementation of a piezoelectric power harvesting device to capture vibrational strength from pipelines to autonomous strength IoT devices. The gadget utilizes key components along with the PPA-1001 piezoelectric sensor, STM32F103C8T6 microcontroller, and LTC-3588 energy harvesting strength delivery. Experimental results verified the gadget's performance in harvesting strength within a specific frequency variety of 10 Hz to 50 Hz, with the foremost overall performance at 30 Hz. The device generated the highest voltage of 3.3V, delivering a strength output of 2.18 mW, which is sufficient to power low-strength electronic gadgets. The device maintained solid performance across a temperature range of 20°C to 35°C, underscoring its robustness in various environmental situations. The findings highlight the capacity of this generation to offer a sustainable power source for far-off pipeline tracking, contributing to stronger protection and operational efficiency.

This work presents the study of a reproducible acoustic emission method based on the launching of a metallic sphere and low-cost piezoelectric diaphragm. For this purpose, tests were first conducted on a carbon fiber-reinforced polymer structure, and then on an aluminum structure for comparative analysis. The Pencil Lead Break (PLB) tests were also conducted for comparisons with the proposed method. Different launching heights and elastic deformations of the structures were investigated. The results show higher repeatability for the sphere impact method, as the PLB is more affected by human inaccuracy, and it was also effective in damage detection.

The technological development of piezoelectric materials is crucial for developing wearable and flexible electromechanical devices. There are many inorganic materials with piezoelectric effects, such as piezoelectric ceramics, aluminum nitride, and zinc oxide. They all have very high piezoelectric coefficients and large piezoelectric response ranges. The characteristics of high hardness and low tenacity make inorganic piezoelectric materials unsuitable for flexible devices that require frequent bending. Polyvinylidene fluoride (PVDF) and its derivatives are the most popular materials used in flexible electromechanical devices in recent years and have high flexibility, high sensitivity, high ductility, and a certain piezoelectric coefficient. Owing to increasing the piezoelectric coefficient of PVDF, researchers are committed to optimizing PVDF materials and enhancing their polarity by a series of means to further improve their mechanical–electrical conversion efficiency. This paper reviews the latest PVDF-related optimization materials, related processing and polarization methods, and the applications of these materials such as those in wearable functional devices, chemical sensors, biosensors, and flexible actuator devices for flexible micro-electromechanical devices. We also discuss the challenges of wearable devices based on flexible piezoelectric polymer, consider where further practical applications could be.

Satellites are subject to various severe vibration during different phases of flight. The concept of satellite smart adapter is proposed in this study to achieve active vibration control of launch vehicle on satellite. The satellite smart adapter has 18 active struts in which the middle section of each strut is made of piezoelectric stack actuator. Comprehensive conceptual design of the satellite smart adapter is presented to indicate the design parameters, requirements and philosophy applied which are based on the reliability and durability criterions to ensure successful functionality of the proposed system. The coupled electromechanical virtual work equation for the piezoelectric stack actuator in each active strut is drived by applying D'Alembert's principle. Modal analysis is performed to characterize the inherent properties of the smart adapter and extraction of a mathematical model of the system. Active vibration control analysis was conducted using fuzzy logic control with triangular membership functions and acceleration feedback. The control results conclude that the proposed satellite smart adapter configuration which benefits from piezoelectric stack actuator as elements of its 18 active struts has high strength and shows excellent robustness and effectiveness in vibration suppression of launch vehicle on satellite.

PZT-Poly(vinylidene fluoride) composites were prepared by hot-pressing method. Before addition, PZT particles were firstly modified with two different coupling agents. The micromorphology, microstructure, dielectric properties, and piezoelectric properties of the composites were characterized and investigated. Results indicated that PZT particles were homogeneously dispersed in the PVDF matrix by the addition of coupling agents. The electric properties of PZT-PVDF composites with NDZ-101 were the best. Especially when the volume ratio of the titanate coupling agent NDZ-101 was 1%, the piezoelectric strain constant d33 of PZT-PVDF composites reached maximum value 19.23pC/N; its relative dielectric constant εr was 67.45; at the same time its dielectric loss tanδ was 0.0766.

N,N-dimethyl-4-nitroaniline (NNDM4NA, C8H10O2N2), is a superelastic and superplastic charge-transfer molecular crystal with a high molecular dipole moment, µ=7.95 D, which crystal-lizes in the acentric polar point group 2. Highly aligned poly-l-lactic acid (PLLA) polymer micro-fibers with embedded NNDM4NA nanocrystals were fabricated using the electrospinning tech-nique. The composite fibers display an extraordinarily high piezoelectric output response, where for a small stress of 5.0x103 Nm-2, an effective piezoelectric voltage coefficient of geff=3.6 VmN-1 was obtained. The fibers were found to display solid state blue fluorescence with a long (147 ns) life-time decay. Furthermore, the composite fibers exhibit an average increase of 67% on the Young modulus reaching 55 MPa, while the tensile strength reaches 2.8 MPa when compared with solely PLLA fibers. The results show that nanocrystals, from small organic molecules, with elastic and piezoelectric properties form hybrid functional 2-dimensional luminescent array which are me-chanical strong and generate high output voltages making them promising for applications in energy harvesting and as solid-state blue emitters.

In this paper, we present a study of various ZnO/SiO2-stacked thin film structures for flexible micro-energy harvesting devices. Two groups of micro-energy harvesting devices, SiO2/ZnO/SiO2 micro-energy generators (SZS-MGs) and ZnO/SiO2/ZnO micro-energy generators (ZSZ-MGs), were fabricated by stacking both SiO2 and ZnO thin films, and the resulting devices were characterized. With a particular interest in the fabrication of flexible devices, all the ZnO and SiO2 thin films were deposited on ITO-coated PEN substrates using an RF magnetron sputtering technique. The effects of the thickness and/or position of the SiO2 films on the device performance were investigated by observing the variations of output voltage in comparison with that of a control sample. As a result, compared to the ZnO single-layer device, all the ZSZ-MGs showed much better output voltages, while all the SZS-MG showed only slightly better output voltages. Among the ZSZ-MGs, the highest output voltages were obtained from the ZSZ-MGs where the SiO2 thin films were deposited using a deposition power of 150 W. Overall, the device performance seems to depend significantly on the position as well as the thickness of the SiO2 thin films in the ZnO/ SiO2-stacked multilayer structures, in addition to the processing conditions.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

The field of power harvesting has experienced significant growth over the past few years due to the ever-increasing desire to produce portable and wireless electronics with extended lifespans. The present work aims to introduce an approach to harvesting electrical energy from a mechanically excited piezoelectric element and investigates a power analytical model generated by a smart structure of type polyvinylidene fluoride(PVDF) that can be stuck onto fabrics and flexible substrates, although we report the effects of various substrates and investigates the sticking of these substrates on the characterization of the piezoelectric material.

Since fine powders tend strongly to adhesion and agglomeration, their processing with conventional methods is difficult or impossible. Typically, in order to enable the handling of fine powders, chemicals are added to increase the flowability and reduce adhesion. This contribution shows that instead of additives also vibrations can be used to increase the flowability, to reduce adhesion and cohesion, and thus to enable or improve processes such as precision dosing, mixing, and transport of very fine powders. The methods for manipulating powder properties are described in detail and prototypes for experimental studies are presented. It is shown that the handling of fine powders can be improved by using low-frequency, high-frequency or a combination of low- and high-frequency vibration.

This article reviews recent innovations in piezoelectric actuators, then indicates the future research targets. In the materials, the piezoelectric performances of relaxor-lead titanate (PZN-PT, PMN-PT) single crystals have been improved significantly by an AC electric poling technique. Also new loss characterization techniques facilitate developing high-power density piezoelectrics. The RMS vibration velocity reaches 0.6 m/s in the k₃₁ mode in lead zirconate titanate (PZT) nowadays, which corresponds to power density 30 W/cm³. Pb-free materials are urged due to the recent political regulation on toxic materials. In device designs, the original multilayer actuators (MLA) with Ag/Pd electrode have been switched to the ones with Cu or pure Ag, in order to suppress the heat generation, then to enhance the device power density. Piezoelectric micro-electro-mechanical-systems (MEMS’s) started to utilize the <1 0 0> oriented epitaxial films of rhombohedral PZT compositions, which exhibits enhanced piezoelectric properties. Also for higher-power applications, aero-sol deposition (AD) methods have been introduced to 10 -thick films. Regarding drive/control techniques in piezo-actuators, three developments are on-going, that is, “negative capacitance” power supplies for driving off-resonance (pseudo-DC) piezo-actuators, capacitive AC power supplies for efficiently driving resonance piezo-actuators, and DC/DC converters for harvesting electric energy from high-impedance piezoelectric devices under noise vibration. The applications of piezoelectric actuators in the 21^st century seem to be oriented toward “politico-engineering” with four keywords, “cooperation, protection, reduction, and continuation”. The sustainability technologies include the following piezoelectric items: (a) Pb-free piezoelectrics, (b) ultrasonic technology for decomposing hazardous materials, (c) reduction of contamination gas, (d) piezoelectric energy harvesting, and (e) device improvement with high energy-efficiency. On the other hand, the following crisis technologies have been developed with piezoelectrics: (a) detection and neutralization technologies of infectious/epidemic diseases such as anthrax, (b) autonomous unmanned underwater, aerial, and land vehicles with piezoelectric actuators, (c) pin-point target weapons, (d) high voltage supplies with piezoelectric transformers, and (e) compact energy sources for remote actuating/sensing systems.

The purpose of this research work was to synthesis bio-derived nanocomposite films by incorporating Na0.5Bi0.5TiO3 (NBT) nanoparticles into Chitosan matrix. The NBT nanoparticles were synthesized using a traditional solid-state technique. Then, through a solution casting approach, flexible composite films were fabricated using Chitosan polymer. The morphology and structural assessments were carried out utilizing scanning electron microscopy (SEM), X-ray diffraction and fourier transform infrared technique. The SEM micrographs showed that NBT nanoparticles were randomly distributed and interconnected with other particles, forming interconnected grains with substantial interspaces within the matrix. The spectral response between 300 and 800 nm of the composites is mainly governed by light scattering of NBT particles with diameter sizes in the 100 - 400 nm range and the bandgap of the NBT phase. The dielectric studies demonstrated that the composite films exhibited higher dielectric values compared to the pure Chitosan film. Besides, the increase of NBT amount was found to increase the dielectric values. Additionally, local piezoelectric measurements reveal the expected piezoelectric and ferroelectric behavior for the NBT particles dispersed into the polymer matrix, as locally probed by Piezoresponse Force Microscopy. The studied system bears interest for advanced biocompatible opto- and piezo-electric materials.

In this paper, we present a finite element simulation of an adaptive piezoelectric fluid-membrane lens modeled in COMSOL Multiphysics. The simulation couples the piezoelectric effect with the fluid dynamics to model the interaction between piezoelectric forces and fluid forces. Also, the simulation is extended to model the thermal expansion of the fluid. Finally, we compare the simulation and experimental results of the adaptive lens refractive power at different actuation levels and temperatures.

In review, the operating principles of the most common bio sensing devices, detection methods and the identification sensitivity of analyzed molecules were shown. The central focus was done on hybridization analysis of nucleic acids (NA), which are considered to be one of the most important analytes in terms of diagnostic point of view. Constructions enabling to transfer the fact of formation of nucleotide probe/target complex in to detectable signal by optical, electrochemical or micromechanical (piezoelectric) sensors were presented in this review.

Piezoelectric nanotransducers may offer key advantages in comparison with conventional piezoelectrics, including more choices for types of mechanical input, positions of the contacts, dimensionalities and shapes. However, since piezo-semiconductive nanostructures are generally much easier to fabricate and integrate into functional systems than insulating materials, modeling becomes significantly more intricate and the effects of free charges have been considered only in a few studies. The available reports are complicated by the absence of proper nomenclature and figures of merit. Besides, some analyses are incomplete. For instance, the local piezopotential and free charges within axially strained conical piezo-semiconductive nanowires have only been systematically investigated for very low doping (1016 cm-3) and under compression. Here we give the definitions for the enhancement, depletion, base and tip piezopotentials, their characteristic lengths and both the tip-to-base and the depletion-to-enhancement piezopotential-ratios. As an example, we use these definitions for analyzing the local piezopotential and free charges in n-type ZnO truncated conical nanostructures with different doping levels (intrinsic, 1016 cm-3, 1017 cm-3) for both axial compression and traction. The definitions and concepts presented here may offer insight for designing high performance piezosemiconductive nanotransducers.

With demand for the long-term continued use of existing building facilities, structural health monitoring and damage detection are attracting interest from society. Sensors of various types have been practically applied in the industry to satisfy this need. Among the sensors, piezoelectric sensors are an extremely promising technology by virtue of their cost advantages and durability. Although they have been used in aerospace and civil engineering, their application for building engineering remains limited. Remarkably, recent catastrophic seismic events have further rein-forced the necessity of rapid damage detection and quick judgment about the safe use of facilities. Faced with these circumstances, this study was conducted to assess the applicability of piezoelectric sensors to evaluate building components. Specifically, this study emphasizes structural damage caused by earthquakes. After first applying to cyclic loading tests to composite beam component specimens and steel frame subassemblies with a folded roof plate, the prospective damage posi-tions were also found using finite element analysis. Crack propagation and buckling locations were predicted adequately. The piezoelectric sensors provided output when the concrete slab showed tensile cracks, or when the folded roof plate experienced local buckling. Furthermore, damage expansion and progression were detected multiple times during loading tests. Results showed that the piezoelectric sensors can detect structural damage of building components, demonstrating their potential for use in inexpensive and stable monitoring systems.

Statistical based reconstruction methods and signal processing tooling techniques are implemented and used to detect delaminations or debondings within composite items. From literature it appears that, although a single procedure for the estimation of the structural health is a fast solution, a multiple analysis based on different reconstruction methods or different damage parameters could provide more detailed information about the location and the severity of possible failures. This work discusses the advantage of using cross-correlation analysis in a data-driven approach based on ultrasonic guided waves (GW) tomographic technique and piezoelectrics (PWAS) in pitch-catch configuration. In this sense, this work evidences an improvement in damage detection when the cross-correlation is included as part of the GW-based system for damage assessment approach. The specimens used as test structures to demonstrate the validity of the methodology derive from an aircraft wing test article where damages are specified as skin delamination produced by low energy impact.

Owing to the escalating adoption of IoT systems across various domains, the demand for mobile and wireless power sources has surged. Although conventional batteries typically serve as energy storage components, the current low-power consumption devices necessitate eco-friendly alterna-tives. In this study, we designed, fabricated, and characterized an energy harvesting device that repurposes mechanical vibrations. A three-beam design was employed to harvest energy across a broader range of potential frequencies. Finite element models were simulated to ascertain the first bending moment for both sets of beams. A nanostructured piezoelectric multilayer film made of ZnO was deposited onto an AISI 304 steel substrate, and a photosensitive resin seismic mass was implemented. Low-cost techniques generating minimal environmental waste were leveraged in the fabrication process. The piezoelectric film was deposited using a spray nebulization technique involving recycled materials and cost-effective equipment. Micrographs of the layers unveiled the presence of nanospheres with diameters of 250 nm. Employing a custom-made shaker, output voltages of 1.08 V and 180 mV, and power outputs of 1.849 µW and 16.2 nW were achieved for each set of beams. The electrical characterization was conducted using a custom-made shaker, repurposing materials for this objective.

The ordered Ca3TaGa3Si2O14 and disordered La3Ga5SiO14 crystals of the lantangallium silicate family were grown by the Czochralski method. The independent coefficients of thermal expansion of crystals αc and αa were determined by X-ray powder diffraction based on the analysis of X-ray diffraction spectra measured in the temperature range of 25÷1000°C. It is shown that in the temperature range of 25÷800°C the thermal expansion coefficients are linear. At temperatures above 800°C there is a nonlinear character of the thermal expansion coefficients associated with a decrease in the Ga content in the crystal lattice of the lantangallium silicate family crystals.

Abstract: Background: Non-invasive acquistion of beat-to-beat pulse transit time (PTT) via piezoelectric/piezocapacitive sensors (PES/PCS) may expand perioperative hemodynamic monitoring. This study evaluated the ability for PTT via PES/PCS to correlate with systolic, diastolic, and mean invasive blood pressure (SBPIBP, DBPIBP, and MAPIBP) and to detect SBPIBP fluctuations. Methods: PES/PCS and IBP measurements were performed in 20 patients undergoing abdominal, urological, and cardiac surgery. A Pearson’s correlation analysis (r) between 1/PTT and IBP was performed. The predictive ability of 1/PTT with changes in SBPIBP was determined by area under the curve (reported as AUC, sensitivity, specificity). Results: Significant correlations between 1/PTT and SBPIBP were found for PES (r=0.64) and PCS (r=0.55) (p<0.01), as well as MAPIBP/DBPIBP for PES (r=0.6/0.55) and PCS (r=0.5/0.45) (p<0.05). A 7% decrease in 1/PTTPES predicted a 30% SBPIBP decrease(0.82, 0.76, 0.76), while a 5.6% increase predicted a 30% SBPIBP increase (0.75, 0.7, 0.68). A 6.6% decrease in 1/PTTPCS detected a 30% SBPIBP decrease (0.81, 0.72, 0.8), while a 4.8% 1/PTTPCS increase detected a 30% SBPIBP increase (0.73, 0.64, 0.68). Conclusions: Non-invasive beat-to-beat PTT via PES/PCS demonstrated significant correlations with IBP and detected significant changes in SBPIBP. Thus PES/PCS as a novel sensor technology may augment intraoperative hemodynamic monitoring during major surgery.

In this study, a preload monitoring method using impedance signatures obtained from a piezoelectric-based smart interface is presented for bolted girder connections. Firstly, the background theory of the piezoelectric-based smart interface and its implementation into health monitoring of bolted connections are outlined. A simplified electro-mechanical (EM) impedance model of a smart interface-embedded bolted connection system is formulated to interpret mechanistic understanding of EM impedance signatures under the effect of bolt preload. Secondly, finite element modeling of a bolted connection is carried out to show the numerical feasibility of the presented method and to predetermine the sensitive frequency band of impedance signatures. Finally, impedance measurements are conducted on a lab-scaled bolted girder connection to verify the predetermined sensitive frequency range and to assess the bolt preload changes in the test structure.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

In this paper, a resonant system that produces a movement of low amplitude and ultrasonic frequency is used to achieve the vibration assistance in a ball-burnishing process. A full vibration characterization of this process performed in a lathe was done. It is carried out by a new tool designed in the research group of the authors. Its purpose is to demonstrate that the machine and the tool do not have any resonance problem during the process and to prevent possible failures. The analysis of this dynamic behaviour permits to validate the suitability of the tool when it is anchored to a numerical control lathe. This is very important for its future industrial implementation. It is also intended to confirm that the system adequately transmits vibrations through the material. To do this, a methodology to validate the dynamic tool behaviour was developed. Several techniques that combine the usual and ultrasonic vibration ranges through static and dynamic measurements were merged: vibration and acoustic emission measurements. An operational deflection shape (ODS) exercise has been also performed. Results show the suitability of the tool used to transmit the assistance vibrations, and that no damage is produced in the material in any case.

A high-performance Lead-free Piezoelectric Energy Harvester (LPEH) based on a Ba0.85Ca0.15Ti0.90Zr0.10O3 + CuO 0.3 wt% (BCTZC0.3) composite was fabricated by sintering at 1450℃. The BCTZC0.3 composite, which has an enhanced high-energy-conversion constant (〖d_33×g〗_33), shows improved piezoelectric power-generation performance when compared with conventional piezoelectric energy harvesters. The BCTZC0.3-based LPEH produces instantaneous maximum power of 8.2 mW and an energy density of 107.9 mW/cm3 in a weak magnetic field of 250 μT. This energy harvester can be used to charge a capacitor and operate a wireless sensor network (WSN) system to provide temperature sensing and radio-frequency (RF) transmission in a 250 μT magnetic field. The proposed LPEH is a promising green-energy device for potentially self-powering WSN systems when applied.

First of all the paper presents a solid solution of piezoelectric ceramic that was synthesized according to the general formula Pb(1-x)Srx(Ti0.48Zr0.52)(1-y)NbyO3 with x = 0.05 and y = 0.02, using wet ceramic processing technology and using an oxide mix as prime material. The effects of dopants (Sr2+ and Nb5+) on phase constitution, on microstructure and on the dielectric and piezoelectric properties were determinate. The Zr/Ti ratio was chosen near the morphotropic phase boundary of the PZT system in studied composition. The XRD data revealed that the PZT doped composition had tetragonal perovskite structure. Secondly the paper presents the design of the novel piezo-motor based on a surface wave which translates the linear extension of different piezoelectric segments of a piezoelectric cylinder into a rotational bending movement. This rotational bending of the piezoelectric cylinder is then transformed into a continuous rotation of the rotor through a calculated contact. The design of the motor takes advantage of the high piezoelectric constants of the developed material in an optimal way in order to increase the energetic efficiency. A brief mathematical model of electromechanical answer of piezoelectric materials is presented as it was used in the modeling of the material during the numerical simulations.

Ultrasound, as mechanical waves with frequencies exceeding 20 thousand hertz, has found wide applications in medicine, physiotherapy, and more recently in agriculture. This study aimed to investigate the impact of ultrasound on potato yield and its parameters, particularly on seed potato yield, quantity, mass, and multiplication coefficient of potato tubers. The research was based on a three-year field experiment, utilizing the randomized block design in a split-split-plot arrangement, in the central-eastern region of Poland. The primary factor were technologies: a) technology with employing ultrasonic pre-planting treatment, b) traditional cultivation without this treatment. The secondary factors were potato varieties. Sonication of tubers was conducted using a bath-type ultrasonic device equipped with piezoe-lectric transducers. Results revealed a significant influence of cultivation technology, cultivar, and weather conditions on seed tubers yield, quantity, and multiplication coefficient of potato tubers. However, genetic traits of the examined varieties and random factors significantly affected the individual seed tuber mass and the number of shoots emerging from a single tuber. Future Outlook: Future research could focus on further optimizing ultrasound application techniques in potato cultivation, considering diverse varieties and environmental conditions. Additionally, it would be worthwhile to analyze the long-term effects of ultrasound on tuber seed potato quality and their ability to adapt to changing climatic and soil conditions. Furthermore, studies investi-gating the impact of ultrasound on other plant species could broaden our understanding of po-tential benefits in agriculture.

The detection and analysis of small molecules, typically defined as molecules under 1000 Da, is of growing interest ranging from the development of small molecule drugs and inhibitors to the sensing of toxins and biomarkers. However, due to challenges such as their small size and low mass, many biosensing technologies struggle to have the sensitivity and selectivity for the detection of small molecules. Notably, their small size limits the usage of labeled techniques that can change the properties of small molecule analytes. Furthermore, the capability of real-time detection is highly desired for small molecule biosensors’ application in diagnostics or screening. This review highlights recent advances in label-free real-time biosensing technologies utilizing different types of transducers to meet the growing demand for small molecule detection.

Concrete-filled steel tube (CFST) members have been widely used in the field of civil engineering due to their advanced superior mechanical properties. However, internal defects such as concrete core voids and interface debonding are likely to weaken the load-carrying capacity and stiffness of these members, which affects safety and serviceability of CFST structures. Visualizing the inner defects of concrete core in CFST members have been a critical need in civil engineering construction, a travel time tomography (TTT) is introduced to quantitatively identify and visualize the sizes and positions of CFST members in this paper. Moreover, a parameter analysis is performed to investigate the relationship between TTT imaging qualities and influence factors, e.g. inversion parameters, defect sizes and positions. The effectiveness and accuracy of the TTT algorithm are verified by several numerical examples and the results demonstrate that TTT can identify the sizes and positions of concrete core void defects in CFST members efficiently and several inversion parameters including model weighting matrix and inversion grid size really pose a significant impact on the imaging results of CFST members. In addition, several optimum parameters are recommended to benefit the future study of the promising TTT approach for CFST members.

The work presents a Structural Health Monitoring (SHM) electronic system with real-time ac-quisition and processing for the determination of impact location in laminates. The novelty of this work is the quantitative evaluation of impact location errors using the Lamb wave guided mode S0, captured and processed in real-time by up to eight piezoelectric sensors. The differential time of arrival is used to minimize an error function for the position estimation. The impact energy is correlated to the amplitudes of the antisymmetric (A0 ) mode and the electronic design is de-scribed to avoid saturation for signal acquisition. The same electronic is designed to acquire symmetric (S0 ) low level signals by adequate gain, bandwidth and signal to noise ration. Such signals propagate into a 1.4mm thick aluminum laminate at the group velocity of 5150m/s with frequency frequency components above 270kHz and can be discriminated from the A0 mode to calculate accurately the differential arrival time. The results show that the error is not improved better than S0 wavelength in impact localization by using six out of eight sensors connected to the electronic system.

A new circuit model of the self-powered device for heart rate measurement is presented in this paper. This device consists of piezoelectric energy harvester (PEH), power management circuit (PMC) with energy storage, microcontroller, Photoplethysmography (PPG) sensor, and Wi-Fi module. The PEH is placed under the insole to harvest the pressure energy from human foot-step to generate ac power. In our model, a PEH is represented by sine voltage source, where its parameters were taken from experiments with 20 volunteers. The PMC is simplified by a switch with gain δ placed in series with the main circuit. The model of the main circuit is RC elements in parallel, where C is the capacitance of the storage device, and R is the equivalent parallel resistance of the microcontroller, PPG sensor, and Wi-Fi modules, respectively. The value of R depends on the power and current absorbed by those modules during sleep, deep sleep, sense, and transmit modes which collected from the datasheet. Finally, the proposed circuit model of the self-powered device was built and simulated in SPICE. The simulation results were compared with the laboratory experiment using commercial devices. Based on the results, the proposed model had small gaps compared to the real self-powered devices in terms of average current, voltage, power and efficiency.

We mainly describe the influence factors of captured power by huge wave energy harvesters, which the vertical motion of buoy can transform ocean’s potential energy into piezoelectric energy power by waves. By means of semi-analytical solutions and theoretical analysis, related environmental coefficients are analyzed firstly and find the most appropriate wave frequency and geometric structure as reference. Secondly, the numerical results also discuss the impact trend of hydrodynamic parameters and geometric volume on motion, voltage and power with qualitative agreement. The simulation data confirm that structure parameters of the modified model could markedly deliver sufficient power to ocean high electrical equipment with long-time stability.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&amp;O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&amp;O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

The composition of fine-ground lead zirconate-titanate powder Pb(Zr_0.52Ti_0.48)O₃, suspended in PZT and bismuth titanate (BiT) solutions, is deposited on the curved surface of IN718 and IN738 nickel-based supper alloy substrates up to 100 µm thickness. Photochemical metal organic and infiltration techniques are implemented to produce smooth, semi-dense, and crack-free random orientated thick piezoelectric films as piezo-sensors, free of any dopants or thickening polymers. Every single layer of the deposited films is heated at 200 °C with 10 wt.% excess PbO, irradiated by UV lamp (365 nm, 6 watt) for 10 minutes, pyrolyzed at 400 °C, and subsequently annealed at 700 °C for one hour. This process is repeated successively until reaching the desired thickness. Au and Pt thin films are deposited as the bottom and top electrodes using evaporation and sputtering methods, respectively. PZT/PZT and PZT/BiT composite films are then characterized and compared to similar PZT and BiT thick films deposited on the similar substrates. The effect of composition and deposition process is also investigated on the crystalline phase development and microstructure morphology as well as dielectric, ferroelectric and piezoelectric properties of piezo-films. The maximum remnant polarization of P_r = 22.37 ± 0.01, 30.01 ± 0.01 µC/cm², the permittivity of ε_r = 298 ± 3, 566 ± 5 and piezoelectric charge coefficient of d₃₃ = 126, 148 m/V were measured versus the minimum coercive field of E_c = 50, 20 kV/cm for the PZT/PZT and PZT/Bit thick films, respectively. The thick film piezo-sensors are developed to be potentially used at frequency bandwidth of 1–5 MHz for rotary structural health monitoring and also in other industrial or medical applications as a transceiver.

This paper presents a demonstration of the feasibility of fabricating micro-cantilever harvesters with extended stress distribution and enhanced bandwidth by exploiting an M-shaped two-degrees-of-freedom design. The measured mechanical response of the fabricated device displays the predicted dual resonance peak behavior with the fundamental peak at the intended frequency. This design has the features of high energy conversion efficiency in a miniaturized environment where the available vibrational energy varies in frequency. It makes such a design suitable for future large volume production of integrated self powered sensors nodes for the Internet-of-Things.

Piezoelectric ultrasonic motors (USMs) are actuators that use ultrasonic frequency piezoelectric vibration generated waves to transform electrical energy into rotary or translating motion. USMs are paid more attention because they offer distinct qualities over traditional magnet-coil-based motors, such as miniaturization, great accuracy, speed, non-magnetic nature, silent operation, straightforward construction, broad temperature operations, and adaptability. This review study focuses on the principle of USMs and their classifications, characterization, fabrication methods, applications, and future challenges. Firstly, the classifications of USMs, especially, standing wave, traveling wave, hybrid mode, multi degree of freedom USMs are summarized, and their respective functioning principles are explained. Secondly, the finite element modelling analysis for design and performance predictions, the conventional and nano/micro fabrication methods, and, the various characterization methods are presented. Thirdly, their advantages, such as high accuracy, small size, and silent operation and their benefits over conventional motors for the different specific applications are examined. In addition, the substantial contributions to a variety of tech-nical fields like surgical robots, industrial, aerospace, and biomedical applications are introduced. Finally, their future prospects and challenges in USMs development, with an emphasis on downsizing, increasing efficiency, and new materials are outlined.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

Ultrasonic imaging & NDE applications can greatly improve their signal-to-noise ratios (SNR) by driving each transducer (composing piezoelectric arrays) with a spike giving pulsed power of k-Watts, repetitively at a PRF = 5000 spikes/s, by using a HV capacitive-discharge generator. However very-high levels, of pulsed intensities (3-10 A) and voltages (300-700 V) must be considered for a rigorous spike modeling. Even though the consumed "average" power will be small, the intensity through each transducer achieves several amperes, so the pulsed powers delivered by each HV generator can attain levels higher than in CW high-power ultrasonic applications: e.g., up to 5 kW / spike. This is concluded here from a transient modeling of the loaded generator. Then, unforeseen phenomena rise: intense brief pulses of driving power & emitted force in transducers, and non-linearities in driver semiconductors, because their characteristic curves only include linear ranges. But fortunately, piezoelectric devices working in this intense regime do not show serious heating problems, because the average power remains being moderate. Intensity, power and voltage, driving a broadband transducer from a HV capacitive pulser, are calculated to drastically improve (in ≅ 40 dB) the ultrasonic net dynamic range available, with emitted forces ≅ 250 Newtons pp and E/R received pulses of 70 V pp.

A novel effective vibrational mode was discovered in the conventional transducer with an array of orthogonal (square) regular piezoelectric rods in 1-3 piezocomposite, containing the damping backing and front matching layers. The operational resonance in the structure was determined as the Surface Acoustic Wave (SAW) on the backing boundary excited by the adjacent piezo-rods, with its frequency typically near 3 times lower the fundamental half-lambda conventional piezocomposite resonance. Pulse-echo sensitivity and transmitting sound-pressure-level (SPL) in air showed that the signal strength is roughly comparable to the industrial similar air transducers at the frequency range 100…700 kHz, where at these frequencies the lateral and longitudinal piezoelement dimensions in the conventional transducer design are typically close to each other causing interference with unwanted coupling modes. As was determined theoretically and proved in experiments, the backing SAW resonance effect in the transducer performance is inherent just to the regular periodic 1-3 piezocomposite structure, and does occur neither with randomly located/oriented piezo-rods, nor in the homogeneous piezo-plate at least with the same lateral cross-section as the connected to it backing. The purpose of the article is to investigate a newly discovered operational vibrational mode of a SAW type in 1-3 regular piezocomposite, other than piezoelectric resonance. The investigated phenomena can improve the transceiver sensitivity, bandwidth, providing lower drive voltage, and smaller and lighter weight ultrasonic transducers. Based on the piezocomposites with thickness’ 1…1.5 mm (rod resonance near 2…3 MHz), pillar width 0.2…0.8 mm, kerf width 0.1…0.4 mm, the transceivers with an operating frequency from 140 kHz to 650 kHz were designed and fabricated with a conventional backing of a mixture of high-density tungsten powder and epoxy, and a matching layer of a mixture of low-density glass bubbles and epoxy. Experimental evaluation of their acoustical performance showed expected characteristics suitable for practical applications.

Surgical navigation has evolved as a vital tool in maxillofacial surgery, offering precise and patient-specific data. This study explores the clinical applications and accuracy of intraoperative tool tracking in maxillofacial surgery. The research includes 37 patients with various pathologies who underwent surgery assisted by a surgical navigation system using tracked instruments. The study showcases two representative cases: one involving coronoid hyperplasia with mouth opening deficit and another addressing nose-orbital-ethmoidal-frontal ossifying fibroma resection. The results indicate that surgical navigation with tracked instruments provides high precision (<1.5 mm error), reduced surgical time, and less invasive approaches. The study highlights the potential for reproducible outcomes and increased safety, especially in complex cases. Despite some limitations, the synergy between surgical navigation and tracked instruments offers a promising approach in maxillofacial surgery, expanding its applications beyond current practices.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

This review article is focused on the analysis of the state of the art of sensors for guided 9 ultrasonic waves for the detection and localization of impacts, therefore of interest for the structural 10 health monitoring (SHM). The recent developments in sensor technologies are then reported and 11 discussed through the many references in recent scientific literature. The physical phenomena re-12 lated to impact event and the main physical quantities are then introduced to discuss their im-13 portance in the development of the hardware and software components for SHM systems. An im-14 portant aspect of the article is the description of the different ultrasonic sensor technologies cur-15 rently present in the literature and what advantages and disadvantages they could bring, in relation 16 to the various phenomena investigated. In this context, the analysis of the front-end electronics is 17 deepened, the type of data transmission both in terms of wired and wireless technology and in terms 18 of online and offline signal processing. The integration aspects of sensors for the creation of net-19 works with autonomous nodes with the possibility of powering through energy harvesting devices 20 and the embedded processing capacity is also studied. Finally, the emerging sector of processing 21 techniques using deep learning and artificial intelligence concludes the review by indicating the 22 potential for the detection and autonomous characterization of the impacts.